DATA SHEET
Summit X670-G2 Series
Scalable Advanced 10Gb Aggregation and Data Center Switch with
ExtremeXOS™ Modular Operating System
BENEFITS
BUSINESS ALIGNMENT
• X670-G2-48x-4q – 48 ports of 1/10Gb
SFP+ with 4 ports of 10/40Gb QSFP+
• X670-G2-72x – 72 ports of 1/10Gb SFP+
in 1 RU form factor
OPERATIONAL EFFICIENCY
• Full ExtremeXOS® feature set
supporting switching, routing, SDN,
Data Center Bridging, MPLS, and Audio
Video Bridging
• SummitStack™ support enables flexible
Product Overview
The Summit X670-G2 product family provides high density 10 Gigabit Ethernet and
40 Gigabit Ethernet switching in a small 1RU form factor. With its versatile design,
the Summit X670-G2 provides high density Layer 2/3 10Gb networking with low
latency cut-through switching, and IPv4 and IPv6 unicast and multicast routing to
stacking configurations with entire
enable enterprise aggregation and core backbone deployment in AC-powered and
stackable Summit product line
DC-powered environments.
• IEEE 1588 PTP Timing with integrated
timing output ports
• All configurations provide non-blocking,
line rate performance
The Summit X670-G2 simplifies network operation with the ExtremeXOS modular
operating system (OS), which is used among all Extreme Networks Summit and
BlackDiamond Ethernet switches. The high availability ExtremeXOS operating
system provides simplicity and ease of operation through the use of one OS
• Low latency cut-through mode
everywhere in the network.
• Front-to-Back or Back-to-Front
The Summit X670-G2 comes in two models:
airflow
• X670-G2-48x-4q – 48 ports of 1/10Gb SFP+ with 4 ports of 10/40Gb QSFP+
• X670-G2-72x – 72 ports of 1/10Gb SFP+ in 1 RU form factor
The Summit X670-G2-48x-4q supports four QSFP+ ports of 40 GbE. Each 40
Gigabit Ethernet port can be independently configured as 40 Gigabit Ethernet or 4
x 10 Gigabit Ethernet.
The X670-G2-72x model supports 72 ports of native 1Gb/10Gb SFP+ ports in a
single compact system without the requirement to use break-out cables to achieve
high density 10Gb connections.
High-Performance Stacking
The Summit X670-G2 supports 4 different methods of stacking: SummitStack-V,
SummitStack-V80, SummitStack-V160, and SummitStack-V320.
SummitStack-V—Flexible Stacking Over 10 Gigabit Ethernet
ExtremeXOS supports the SummitStack-V capability using 2 of the native 10
GbE ports on the faceplate as stacking ports, enabling the use of standard
cabling and optics technologies used for 10 GbE SFP+, SummitStack-V provides
long-distance stacking connectivity of up to 40 km while reducing the cable
complexity of implementing a stacking solution. SummitStack-V is compatible
X670 G2 – Data Sheet
1
with Summit X440, X460, X460-G2, X480, X670, X670V
and X770 switches running the same version of ExtremeXOS.
SummitStack-V enabled 10 GbE ports must be physically
direct-connected.
SummitStack-V80/V160/V320—Flexible Stacking Over 40
Gigabit Ethernet
GREEN DESIGN – LOW POWER CONSUMPTION
WITH OPTIMIZED COOLING OPTIONS
The Summit X670-G2 series is designed to be environmentally
green. System power consumption is very low at both highload and idle situations through the power-efficient hardware
design. The power supplies are also highly efficient, which
minimizes the loss of power and unnecessary heat generated
The Summit X670-G2-48x-4q also supports high-speed
by the power supply. Summit X670-G2 series switches can be
80Gbps,160 Gbps, and 320Gbps stacking using QSFP+ ports,
used in AC or DC powered environments.
which is ideal for demanding applications where a high volume
of traffic traverses through the stacking links, yet bandwidth
is not compromised through stacking. SummitStack-V80,
-V160, and -V320 can support passive copper cables (up to
5m), active multi-mode fiber cable (up to 100m), and QSFP+
optical transceivers for 40 GbE up to 10km. With SummitStack,
the Summit X670-G2-48x-4q provides a flexible stacking
solution inside the data center or central office to create a
DESIGNED FOR CLOUD DATA
CENTERS – VEPA, XNV, DCB,
OPENFLOW, OPENSTACK
Summit X670-G2 has a variety of features that fit your data
center needs:
virtualized switching infrastructure across rows of racks.
DIRECT ATTACH (VEPA)
Intelligent Switching and MPLS/H-VPLS Support
can support Direct Attach (VEPA), which eliminates the
Summit X670-G2 supports sophisticated and intelligent Layer
virtual switch layer, simplifying the network and improving
2 switching, as well as Layer 3 IPv4/IPv6 routing including
performance. Direct Attach enables data center simplification
With the optional feature pack, Summit X670-G2 switches
policy-based switching/routing, Provider Bridges, bidirectional
by reducing network tiers from 4 or 5 tiers to just 3 or 2 tiers,
ingress and egress Access Control Lists, and bandwidth
depending on the size of the data center.
control by 8 Kbps granularity both for ingress and egress.
To provide scalable network architectures used mainly for
Carrier Ethernet network deployment, Summit X670-G2
supports MPLS LSP-based Layer 3 forwarding and Hierarchical
VPLS (H-VPLS) for transparent LAN services. With H-VPLS,
transparent Layer 3 networks can be extended throughout the
Layer 3 network cloud by using a VPLS tunnel between the
regional transparent LAN services typically built by Provider
Bridges (IEEE 802.1ad) technology
1588 Precision Time Protocol (PTP)
Summit X670-G2 offers Boundary Clock (BC), Transparent
Clock (TC), and Ordinary Clock (OC) for synchronizing phase
and frequency and allowing the network and the connected
devices to be synchronized down to microseconds of accuracy
over Ethernet connection.
Audio Video Bridging (AVB)
The X670-G2 series supports IEEE 802.1 Audio Video Bridging to
enable reliable, real-time audio/video transmission over Ethernet.
AVB technology delivers the quality of service required for
EXTREMEXOS NETWORK VIRTUALIZATION
(XNV)
To further enhance data center operations, Summit X670-G2
switches support XNV (ExtremeXOS Network Virtualization),
which is natively supported in the ExtremeXOS operating
system and is a licensable feature pack for Ridgeline, a
network and service management application, sold separately.
XNV provides insight, control and automation for virtualized
data centers.
DATA CENTER BRIDGING (DCB)
The Summit X670-G2 series supports Data Center Bridging
features such as Priority Flow Control (PFC), Enhanced
Transmission Selection (ETS) and Data Center Bridging
eXchange (DCBX) for data center convergence.
PFC
Summit X670-G2 switches support Priority-based Flow
Control (PFC, or IEEE 802.1Qbb), which allows network traffic
to be controlled independently based on Class of Service. PFC
today's high-definition and time-sensitive multimedia streams.
allows network traffic that requires lossless throughput to
Low Latency Switching for Cluster Computing
perform better without PFC can continue as normal.
be prioritized,while other traffic types that do not require or
Summit X670-G2 can achieve latency less than 600
nanoseconds and supports cut-through switching for latencysensitive cluster computing.
X670 G2 – Data Sheet
2
SOFTWARE DEFINED NETWORKING
(SDN) OPENFLOW
ExtremeXOS implementations of OpenFlow APIs allow an
external OpenFlow-based SDN controller to access and
control the forwarding plane of ExtremeXOS network devices.
ExtremeXOS-based switches offer a programming interface
through OpenFlow to enable a high degree of automation
in provisioning network services for many upper layer
businesscritical applications running the OpenFlow-based
SDN controller.
OPENSTACK
ExtremeXOS-based switches also allow for integration with
the OpenStack open source cloud computing platform for
public and private clouds through the Extreme Networks
Quantum plugin. The plugin provides a scalable, automated,
rich APIdriven system that enables networking-as-a- service
model managing data center interconnect solutions and large
multitenant networks.
VIRTUAL ROUTERS
In a virtualized environment there is a requirement to support
multiple tenants. In an effort to isolate tenants from each other,
logical separation is established at Layer 3 and Layer 2 level.
ExtremeXOS supports multiple, isolated Layer 3 forwarding
domains by way of Virtual Routers.
ENTERPRISE CORE CLASS SCALABILITY
Modular Operating System for NonStop Operation
LOADABLE SOFTWARE MODULES
The modular design of the ExtremeXOS OS allows the adding
or upgrading of individual software modules dynamically
without requiring a system reboot, leading to higher
availability in the network.
PREEMPTIVE MULTITASKING AND PROTECTED
MEMORY
Summit X670-G2 series switches allow each of many
applications— such as Open Shortest Path First (OSPF)
and Spanning Tree Protocol (STP)—to run as separate OS
processes that are protected from each other. This drives
increased system integrity and inherently protects against
cross-platform DoS attacks.
PROCESS MONITORING AND RESTART
ExtremeXOS increases network availability using process
monitoring and restart. Each independent OS process is
monitored in real time. If a process becomes unresponsive or
stops running, it can be automatically restarted.
Rich OAM Suite – CFM, Y.1731, BFD
Summit X670-G2 series switches supports a rich suite of
protocols to help with Operations, Administration and
The Summit X670-G2 series offers more cost-effective
Maintenance. Connectivity Fault Management (CFM) allows
10 Gigabit Ethernet switches, for both small-sized core
detection, verification, and isolation of connectivity failures
backbone and traditional three-tier network architectures.
in virtual bridged LAN. Y.1731 is largely similar to CFM but
Summit X670-G2 series can support 10 Gigabit Ethernet
also supports performance management by way of frame
campus aggregations with its core class routing and
delay and frame delay variation measurements. Bidirectional
switching scalability.
ONE OPERATING SYSTEM
Extreme Networks simplifies network operation by
offering one common OS – ExtremeXOS – throughout the
BlackDiamond and Summit portfolio. From 10/100 Mbps
switching products such as Summit X430 and Summit X440
to the multi-10 gigabit core backbone BlackDiamond modular
Forwarding Detection (BFD) is a hello protocol that provides
the rapid detection of failures in the forwarding path and helps
the separation of control plane connectivity from forwarding
plane connectivity. By having multiple control plane protocols
like OSPF or MPLS rely on BFD to detect forwarding plane
connectivity failures, network operators can benefit from
simpler network profiling and planning, and consistent and
predictable re-convergence times.
chassis switches, all switches can run the same version of
the OS, which helps deploy, operate and maintain your entire
network and reduce operating costs.
X670 G2 – Data Sheet
3
MPLS
On the Summit X670-G2 series switches MPLS can be enabled,
if needed, by way of an optional feature pack. MPLS provides
the ability to implement traffic engineering and multi-service
networks, and improve network resiliency. The MPLS protocol
suite provides the ability to deploy services based on L2VPNS
(VPLS/VPWS), BGP-based L3VPNS; LSP Establishment based
MULTI-SWITCH LAG (M-LAG)
M-LAG can address bandwidth limitations and improve
network resiliency, in part by routing network traffic around
bottlenecks, reducing the risks of a single point of failure, and
allowing load balancing across multiple switches.
HARDWARE REDUNDANCY
on LDP, RSVP-TE, Static provisioning; Integrated OAM tools
Summit X670-G2 series switches support a dual redundant
like VCCV, BFD and CFM; And MPLS Fast Reroute to support
AC/DC power supply to provide high availability. The power
rapid local convergence around network failures.
supply can be hot-swapped and replaced should it fail. Summit
X670-G2 also supports standardized N+1 redundant hot-
High Availability Network Protocols
swappable fan units.
ETHERNET AUTOMATIC PROTECTION
SWITCHING (EAPS)
Robust IP and MAC Security
Framework
EAPS allows the IP network to provide the level of resiliency
and uptime that users expect from their traditional voice
network. EAPS is more adaptable than Spanning Tree or Rapid
Spanning Tree protocols and can achieve sub-second recovery
that delivers consistent failover regardless of the number
of VLANs, network nodes or network topology in Extreme
Networks-recommended configurations.. EAPS functionality
increases network recovery time, which results in significant
reduction in Voice-over IP call drop rates and improvement in
digital video performance in supported solution configurations.
SPANNING TREE/RAPID SPANNING TREE
PROTOCOLS
Summit X670-G2 supports Spanning Tree (802.1D), Per VLAN
Spanning Tree (PVST+), Rapid Spanning Tree (802.1w) and
Multiple Instances of Spanning Tree (802.1s) protocols for
Layer 2 resiliency.
SOFTWARE-ENHANCED AVAILABILITY
Software-enhanced availability allows users to remain
connected to the network even if part of the network
infrastructure is down. Summit X670-G2 continuously checks
for problems in the uplink connections using advanced
Layer 3 protocols such as OSPF, VRRP and Extreme Standby
Router Protocol (ESRP, supported in Layer 2 or Layer 3), and
dynamically routes traffic around the problem.
EQUAL COST MULTIPATH
MEDIA ACCESS CONTROL (MAC) LOCKDOWN
MAC security allows the lockdown of a port to a given MAC
address and limiting the number of MAC addresses on a
port. This capability can be used to dedicate ports to specific
hosts or devices such as VoIP phones or printers and avoid
abuse of the port—a capability that can be especially useful
in environments such as hotels. In addition, an aging timer
can be configured for the MAC lockdown, protecting the
network from the effects of attacks using (often rapidly)
changing MAC addresses.
IP SECURITY
ExtremeXOS IP security framework helps protect the network
infrastructure, network services such as DHCP and DNS and
host computers from spoofing and man-in-the-middle attacks.
It also protects the network from statically configured and/or
spoofed IP addresses and builds an external trusted database
of MAC/ IP/port bindings providing the traffic’s source from a
specific address for immediate defense.
IDENTITY MANAGEMENT
Identity Manager allows network managers to track users
who access their network. User identity is captured based
on NetLogin authentication, LLDP discovery and Kerberos
snooping. ExtremeXOS uses the information to then report on
the MAC, VLAN, computer hostname, and port location of the
user. Further, Identity Manager can create both roles and policies,
Equal Cost Multipath (ECMP) routing allows uplinks to be
and then bind them together to create role-based profiles based
load balanced for performance and cost savings while also
on organizational structure or other logical groupings, and
supporting redundant failover. If an uplink fails, traffic is
apply them across multiple users to allow appropriate access
automatically routed to the remaining uplinks and connectivity
to network resources. In addition, support for Wide Key ACLs
is maintained.
further improves security by going beyond the typical source/
LINK AGGREGATION (802.3AD)
destination and MAC address as identification criteria access
mechanism to provide filtering capabilities.
Link aggregation allows trunking of up to 32 links on a
single logical connection, for up to 320 Gbps of redundant
bandwidth per logical connection.
X670 G2 – Data Sheet
4
Threat Detection and Response
CLEAR-FLOW SECURITY RULES ENGINE
CLEAR-Flow Security Rules Engine provides first-order threat detection and
mitigation, and mirrors traffic to security appliances for further analysis of
suspicious traffic in the network.
SFLOW
Summit X670-G2 series supports hardware-based sFlow® sampling that provides the
ability to sample application-level traffic flows on all interfaces simultaneously.
PORT MIRRORING
To allow threat detection and prevention, Summit X670-G2 supports many-to-one
and one-to-many port mirroring. This allows the mirroring of traffic to an external
network appliance such as an intrusion detection device for trend analysis or for
utilization by a network administrator for diagnostic purposes. Port mirroring can
also be enabled across switches in a stack.
LINE-RATE INGRESS AND EGRESS ACLS
ACLs are one of the most powerful components used in controlling network
resource utilization as well as in protecting the network. Summit X670-G2 series
supports up to 4,096 ingress ACLs and 1,024 egress ACLs per system based on
Layer 2-, 3- or 4-header information such as the MAC or IP source/ destination
address. ACLs are used for filtering the traffic, as well as classifying the traffic flow
to control bandwidth, priority, mirroring, and policy-based routing/switching.
DENIAL OF SERVICE PROTECTION
Summit X670-G2 series effectively handles Denial of Service (DoS) attacks. If the
switch detects an unusually large number of packets in the CPU input queue, it
assembles ACLs that automatically stop these packets from reaching the CPU. After
a period of time these ACLs are removed, and reinstalled if the attack continues.
ASIC-based LPM routing eliminates the need for control plane software to learn new
flows, allowing more network resilience against DoS attacks.
SECURE AND COMPREHENSIVE NETWORK MANAGEMENT
As the network becomes a foundation of the enterprise application, network
management becomes an important piece of the solution. Summit X670-G2
supports comprehensive network management through Command Line Interface
(CLI), SNMP v1, v2c, v3, and ExtremeXOS ScreenPlay embedded XML-based Web
user interface. With a variety of management options and consistency across
other Extreme Networks modular and stackable switches, Summit X670-G2 series
switches provide ease of management for demanding converged applications.
Extreme Networks has developed tools that simplify and help in efficiently
managing your network. Ridgeline network and service management provides
fault, configuration, accounting, performance and security functions, allowing more
effective management of Extreme Networks products, solutions and thirdparty
devices in a converged network.
Supported Protocols and Standards
A list of supported protocols and standards is available on the
Extreme Networks website at:
http://www.extremenetworks.com/go/xos
X670 G2 – Data Sheet
5
GENERAL SPECIFICATIONS
PHYSICAL SPECIFICATIONS
PERFORMANCE AND SCALE
SUMMIT X670-G2-48X-4Q
Summit X670-G2-48x-4q - 1280Gbps switch bandwidth, 952Mpps
forwarding rate
Height: 1.73 Inches/4.4 cm
Summit X670-G2-72x - 1440Gbps switch bandwidth, 1071Mpps
forwarding rate
Width: 17.4 Inches/44.1 cm
Depth: 19.2 Inches/48.7 cm
9216 Byte maximum packet size (Jumbo Frame)
Weight: 12.85 lbs/5.83 kg
Store-and-Forward and Cut-Through switching support
SUMMIT X670-G2-72
Less than 600 nanoseconds latency
Height: 1.73 Inches/4.4 cm
128 load sharing trunks, up to 32 members per trunk
Width: 17.4 Inches/44.1 cm
4096 VLANS (Port, Protocol, IEEE 802.1Q)
Depth: 19.2 Inches/48.7 cm
4096 ingress and 1024 egress ACL rules per switch
Weight: 15.42 lbs/7.0 kg
FORWARDING TABLES
SUMMIT X670 FAN MODULE
Layer 2 / MAC Addresses: 288K
Height: 1.65 Inches/4.2 cm
IPv4 Host Addresses: 136K
Width: 1.65 Inches/4.2 cm
IPv4 LPM Entries: 16K
Depth: 3.98 inches /10.1 cm
IPv6 Host Addresses: 48K
Weight: 0.357 lbs./0.162 kg
IPv6 LPM Entries: 8K
OPERATING SPECIFICATIONS
CPU, MEMORY
Operating Temperature Range: 0° C to 45° C (32° F to 113° F)
1GHz 64-bit CPU
Operating Humidity: 10% to 95% relative humidity, non-condensing
2GB DDR3 ECC SDRAM
Operating Altitude: 0-3,000 meters (9,850 feet)
4GB eMMC Flash Memory
Operational Shock (Half Sine): 30 m/s2 (3 g), 11ms, 60 Shocks
QOS, RATE LIMITING
Operational Random Vibration: 3-500 MHz @ 1.5g rms
4096 ingress bandwidth meters and 1024 egress meters
STORAGE AND TRANSPORTATION (PACKAGED)
Ingress and egress bandwidth policing/rate limiting per flow/ACL
Transportation Temperature: -40° C to 70° C (-40° F to 158° F)
8 QoS egress queues/port
Humidity: 10% to 95% RH, non-condensing
Egress bandwidth rate shaping per egress queue and per port
Packaged Shock (Half Sine): 180 m/s2 (18 G), 6ms, 600 shocks
Rate Limiting Granularity: 8 Kbps – 1Mbps
Packaged Sine Vibration: 5-62 Hz @ Velocity 5mm/s, 62-500 Hz @ 0.2G
LED INDICATOR
Packaged Random Vibration: 5-20 Hz @ 1.0 ASD w/-3dB/oct. from 20200 Hz
Per port status LED including power status
System Status LEDs: management, fan and power
EXTERNAL PORTS – X670-G2-48X-4Q
48 ports 10GBASE-X SFP+ (1Gb/10Gb dual speed)
4 ports 40GBASE-X QSFP+ (10G/40G dual speed)
One RJ-45 RS-232c Serial port (control port)
One 10/100/1000BASE-T out-of-band management port
EXTERNAL PORTS – X670-G2-72X
72 ports 10GBASE-X SFP+ (1Gb/10Gb dual speed)
One RJ-45 RS-232c Serial port (control port)
One 10/100/1000BASE-T out-of-band management port
POWER SUPPLY SUPPORT
Summit 550W AC PSU - Front-Back and Back-Front airflow options
Summit 550W DC PSU - Front-Back and Back-Front airflow options
14 drops min on sides & corners @ 42” (<15 kg box)
REGULATORY/SAFETY
NORTH AMERICAN SAFETY OF ITE
UL 60950-1 2nd Ed, 2011-12-19, Listed Device (U.S.)
CSA 22.2 #60950-1-07 2nd Ed, 2011-12. (Canada)
Complies with FCC 21CFR 1040.10 (U.S. Laser Safety)
CDRH Letter of Approval (U.S. FDA Approval)
EUROPEAN SAFETY OF ITE
EN 60950-1:2006 2nd Ed. TUV-R GS
EN 60825-1:2007 (Lasers Safety)
2006/95/EC Low Voltage Directive
INTERNATIONAL SAFETY OF ITE
CB Report & Certificate per IEC 60950-1:2005 2nd Ed., + National
Differences
AS/NZS 60950-1 (Australia/New Zealand)
X670 G2 – Data Sheet
6
EMI/EMC STANDARDS
POWER SUPPLY SPECIFICATIONS
NORTH AMERICA EMC FOR ITE
SUMMIT 550W AC PSU
FCC CFR 47 part 15 Class A (U.S.A.)
PHYSICAL SPECIFICATIONS
ICES-003 Class A (Canada)
Height: 1.57 inches (4.0 cm)
EUROPEAN EMC STANDARDS
Width: 3.07 inches (7.8 cm)
EN 55022:2010 Class A
Depth: 13.31 Inches (33.8 cm)
EN 55024:12020
Weight 3.64 lb (1.65 kg)
Class A includes IEC 61000-4-2, 3, 4, 5, 6, 11
POWER SPECIFICATIONS
EN 61000-3-2:2006+A2:2009 (Harmonics)
Voltage input range 90 to 264 V
EN 61000-3-3: 2008 (Flicker)
Nominal input ratings 100 to 240 V, 50 to 60 Hz, 8 A
ETSI EN 300 386 v1.6.1, 2012-09 (EMC Telecommunications)
2004/108/EC EMC Directive
Nominal input current at full loads
•7.5 A @ 90 V (low-line)
•3.7 A @ 230 V (high-line)
INTERNATIONAL EMC CERTIFICATIONS
Line frequency range 47 to 63 Hz
CISPR 22: 2008, (Ed 6.0) Class A (International Emissions)
Maximum inrush current 15 A
CISPR 24:2010 Class A (International Immunity)
Output 12 V, 45 A max, 540 Watts 3.3 V, 3 A max, 9.9 Watts
IEC/EN 61000-4-2:2009 Electrostatic Discharge, 8kV Contact, 15 kV Air,
Criteria A
Maximum continuous DC output shall not exceed 550 Watts
IEC/EN 61000-4-3:2006+A1: 2008+A2:2010, Radiated Immunity, 802500MHz, 5-20V/m, Criteria A
EN 55024:1998+A1:2001+A2:2003 Class A (International Immunity)
IEC/EN 61000-4-4:2012 Transient Burst, 2 kV, Criteria A
IEC/EN 61000-4-5:2006 Surge, 2 kV L-L, 4 kV L-G, Level 3, Criteria A
IEC/EN 61000-4-6:2009 Conducted Immunity, 0.15-80 MHz, 10V/m
unmod. RMS, Criteria A
IEC/EN 61000-4-11:2004 Power Dips & Interruptions, >30%, 25 periods,
Criteria C
COUNTRY SPECIFIC
VCCI:2003-04, Class A (Japan Emissions)
ACMA (C-Tick) (Australia emissions)
BSMI (Taiwan EMC)
CCC Mark (China)
KCC Mark EMC (Korea)
TELECOM STANDARDS
EN/ETSI 300 386:2008 (EMC Telecommunications)
EN/ETSI 300 019 (Environmental for Telecommunications)
IEEE 802.3 MEDIA ACCESS STANDARDS
Power supply input socket IEC 320 C14
Power cord input plug IEC 320 C13
Power supply cord gauge 18 AWG (0.75 mm2) up to 6 feet or 2 meters or
16 AWG (1.0 mm2) over 6 feet
Efficiency 84% typical at full load, high line
SUMMIT 550W DC PSU
PHYSICAL SPECIFICATIONS
Height: 1.57 inches (4.0 cm)
Width: 3.07 inches (7.8 cm)
Depth: 13.31 Inches (33.8 cm)
Weight 2.58 lb (1.17 kg)
POWER SPECIFICATIONS
Nominal Input -48 to -60 VDC, 24 A
DC Voltage Input Range -35 to -75 V
Inrush Current 21A peak
Minimum wire size 14 AWG (1.5 mm2) copper stranded
DC Output 12 V , 45 A/3.3 V, 3 A
DC Output Power (W) 550 W
IEEE 802.3ab 1000BASE-T
IEEE 802.3z 1000BASE-X
IEEE 802.3ae 10GBASE-X
IEEE 802.3ba 40GBASE-X
ENVIRONMENTAL STANDARDS
EN/ETSI 300 019-2-1 v2.1.2 (2000-09) – Class 1.2 Storage
EN/ETSI 300 019-2-2 v2.3.1 (2013-04) – Class 2.3 Transportation
EN/ETSI 300 019-2-3 v2.3.1 (2013-04) – Class 3.1e Operational
EN/ETSI 300 753 (1997-10) – Acoustic Noise
ASTM D3580 Random Vibration Unpackaged 1.5G
X670 G2 – Data Sheet
7
Power Consumption
SWITCH MODEL
MINIMUM HEAT
DISSIPATION
MINIMUM POWER
CONSUMPTION
MAXIMUM HEAT
DISSIPATION
MAXIMUM POWER
CONSUMPTION
Summit X670-G2-48x-4q
325 BTU/hr
95 W
768 BTU/hr
225 W
Summit X670-G2-72x
325 BTU/hr
95 W
939 BTU/hr
275 W
SWITCH MODEL
ACOUSTIC INFORMATION
Summit X670-G2-48x-4q
Dual 550W AC PS with Front to Back (FB) air flow
Bystander Sound Pressure*
• 60.2 dB(A), 0°C to 45°C
Declared Sound Power (LWAd)**
• 7.3 bels, 0°C to 45°C
Dual 550W DC PS with Front to Back (FB) air flow
Bystander Sound Pressure*
• 61.3 dB(A), 0°C to 45°C
Declared Sound Power (LWAd)**
• 7.4 bels, 0°C to 45°C
Dual 550W AC PS with Back to Front (BF) air flow
Bystander Sound Pressure*
• 58.3 dB(A), 0°C to 35°C
• 70.1 dB(A), 45°C
Declared Sound Power (LWAd)**
• 7.0 bels, 0°C to 35°C
• 8.4 bels, 45°C
Dual 550W DC PS with Back to Front (BF) air flow
Bystander Sound Pressure*
• 55.0 dB(A), 0°C to 35°C
• 68.8 dB(A), 45°C
Summit X670-G2-72x
Declared Sound Power (LWAd)**
• 6.5 bels, 0°C to 35°C
• 8.1 bels, 45°C
Dual 550W AC PS with Front to Back (FB) air flow
Bystander Sound Pressure*
• 58.9 dB(A), 0°C to 35°C
• 62.5 dB(A), 45°C
Declared Sound Power (LWAd)**
• 7.3 bels, 0°C to 35°C
• 7.6 bels, 45°C
Dual 550W DC PS with Front to Back (FB) air flow
Bystander Sound Pressure*
• 58.5 dB(A), 0°C to 35°C
• 62.4 dB(A), 45°C
Declared Sound Power (LWAd)**
• 7.3 bels, 0°C to 35°C
• 7.6 bels, 45°C
Dual 550W AC PS with Back to Front (BF) air flow
Bystander Sound Pressure*
• 59.8 dB(A), 0°C to 35°C
• 72.6 dB(A), 45°C
Declared Sound Power (LWAd)**
• 7.3 bels, 0°C to 35°C
• 8.2 bels, 45°C
Dual 550W DC PS with Back to Front (BF) air flow
Bystander Sound Pressure*
• 56.4 dB(A), 0°C to 35°C
• 73.0 dB(A), 45°C
Declared Sound Power (LWAd)**
• 6.7 bels, 0°C to 35°C
• 8.3 bels, 45°C
* Bystander Sound Pressure is presented only for comparison to other products.
**Declared Sound Power is presented in accordance with ISO-7779:2010(E), ISO 9296:2010 per
ETSI/EN 300 753:2012-01
X670 G2 – Data Sheet
8
Supported System Configurations
Fan modules and power supplies must be ordered with all base models. A full
complement of fan modules is required. A single power supply is required with an
optional second power supply for redundancy. AC and DC power supplies can be
mixed in a system. Air flow direction of fan modules and power supplies must match.
FAN MODULES
Base Model
17111
X670 fan module
Front-Back
AC POWER SUPPLIES
17112
X670 fan module
Back-Front
10925
550W AC PSU FrontBack
DC POWER SUPPLIES
10927
550W AC PSU
Back-Front
10926
550W DC PSU
Front-Back
10928
550W DC PSU BackFront
1 or 2
17310 Summit
3
1 or 2
1
X670-G2-48x-4q-
1
1 or 2
Base-Unit
3
1 or 2
1
1
1 or 2
17300 Summit
5
1 or 2
1
X670-G2-72x-BaseUnit
1
1 or 2
5
1 or 2
1
1
Warranty
• One Year
• For warranty details, visit http://www.extremenetworks.com/go/warranty
X670 G2 – Data Sheet
9
Ordering Information
PART NUMBER
PRODUCT NAME
PRODUCT DESCRIPTION
17300
Summit X670-G2-72x-Base-Unit
72 10GBASE-X SFP+, ExtremeXOS Advanced Edge License,
unpopulated dual PSU power slot and 5 unpopulated fan airflow
slots
17310
Summit X670-G2-48x-4q-Base-Unit
48 10GBASE-X SFP+ and 4 40GBASE-X QSFP+, ExtremeXOS
Advanced Edge License, unpopulated dual PSU power slot , and 3
unpopulated fan airflow slots
17111
Summit X670 fan module FB
Fan module for Summit X670 series switches, Front-to-Back
airflow
17112
Summit X670 fan module BF
Fan module for Summit X670 series switches, Back-to-Front
airflow
10925
Summit 550W AC PSU FB
550W AC Power Supply module for Summit switches, Front-toBack airflow
10926
Summit 550W DC PSU FB
550W DC Power Supply module for Summit switches, Front-toBack airflow
10927
Summit 550W AC PSU BF
550W AC Power Supply module for Summit switches, Back-toFront airflow
10928
Summit 550W DC PSU BF
550W DC Power Supply module for Summit switches, Back-toFront airflow
17131
Summit X670 Series Core License
Summit X670 Series Core License
17133
Summit X670 MPLS Feature Pck
Summit X670 MPLS Feature Pack
17134
Summit X670 OpenFlow FeaturePack
ExtremeXOS SDN - OpenFlow Feature Pack for Summit X670
series switches
17135
X670 AVB
ExtremeXOS Audio Video Bridging Feature Pack for Summit X670
series switches
17136
X670-G2 Timing 1588 PTP
ExtremeXOS Network Timing Feature Pack for Summit X670-G2 enables 1588v2 PTP (Precision Time Protocol)
11011
Direct Attach Feature Pack
Direct Attach Feature Pack
16499
Summit X670-3rd Party Optics License
ExtremeXOS 3rd Party Optics (40G and 100G) Feature-Pack for
Summit X670
10319
QSFP+ SR4 module
40 Gigabit Ethernet QSFP+ SR4 optical module, MPO connector,
100m MMF link length
10320
QSFP+ LR4 module
40 Gigabit Ethernet QSFP+ LR4 optical module, LC connectors,
10km SMF link length
10311
QSFP+ passive copper cable, 0.5M
40 Gigabit Ethernet QSFP+ passive copper cable assembly, 0.5m
length.
10312
QSFP+ passive copper cable, 1.0M
40 Gigabit Ethernet QSFP+ passive copper cable assembly, 1m
length.
103131
QSFP+ passive copper cable, 3.0M
40 Gigabit Ethernet QSFP+ passive copper cable assembly, 3m
length.
103231
QSFP+ passive copper cable, 5.0M
40 Gigabit Ethernet QSFP+ passive copper cable assembly, 5m
length.
10315
10m QSFP+ Active Optical Cable
40 Gigabit Ethernet QSFP+ active optical cable assembly, 10m
length.
10316
20m QSFP+ Active Optical Cable
40 Gigabit Ethernet QSFP+ active optical cable assembly, 20m
length.
10318
100m QSFP+ Active Optical Cable
40 Gigabit Ethernet QSFP+ active optical cable assembly, 100m
length.
10321
QSFP+ - 4xSFP+ fan-out cbl, 3m
QSFP+ to 4 x SFP+ fan-out copper cable, 3m
10301
SR SFP+ module
10GBASE-SR SFP+, 850nm, LC Connector, transmission length of
up to 300m on MMF
10302
LR SFP+ module
10GBASE-LR SFP+, 1310nm, LC Connector, transmission length of
up to 10km on SMF
10309
ER SFP+ module
10GBASE-ER SFP+, 1550nm, LC Connector, transmission length of
up to 40km on SMF
10310
ZR SFP+ module
10GBASE-ZR SFP+, 1550nm, LC connector, transmission length up
to 80km on SMF
10304
SFP+ Cable Assembly 1M
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link
lengths of 1m
X670 G2 – Data Sheet
10
PART NUMBER
PRODUCT NAME
PRODUCT DESCRIPTION
10305
SFP+ Cable Assembly 3M
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link
lengths of 3m
103061
SFP+ Cable Assembly 5M
10GBASE-CR SFP+ pre-terminated twin-ax copper cable with link
lengths of 5m
10051H
1000BASE-SX SFP, Hi
1000BASE-SX SFP, MMF 220 & 550 meters, LC connector,
Industrial Temp
10052H
1000BASE-LX SFP, Hi
1000BASE-LX SFP, MMF 220 & 550 meters, SMF 10km, LC
connector, Industrial Temp
10053H
1000BASE-ZX SFP, Hi
1000BASE-ZX SFP, SMF 70km, LC connector, Industrial Temp
10070H2
10/100/1000BASE-T SFP, Hi
10/100/1000BASE-T SFP module, CAT5 cable 100m link, RJ45connector for Giga Bit Ethernet SFP Port, Industrial Temp
1 - Not supported for SummitStack links
2 - Only 1Gb speed supported with 10070H when used with X670-G2
POWER CORDS
In support of the Extreme Networks Green Initiatives, power cords can be ordered seperately but need to be specified at the time order. Please refer to www.
extremenetworks.com/product/powercords/ for details on power cord availability for this product.
http://www.extremenetworks.com/contact
Phone +1-408-579-2800
©2014 Extreme Networks, Inc. All rights reserved. Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc.
in the United States and/or other countries. All other names are the property of their respective owners. For additional information on Extreme Networks Trademarks
please see http://www.extremenetworks.com/company/legal/trademarks/. Specifications and product availability are subject to change without notice. 8882-1014
WWW.EXTREMENETWORKS.COM
X670 G2 – Data Sheet
11