Samsung UN22C4010 Setup guide

Quick Setup Guide
Step 2: Connect Antenna or Cable
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
Step 3: Connect External Devices
Connecting an AV device (DVD / Blu-ray player, cable/satellite box, etc.)
VHF/UHF Antenna
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Best Connection
Connect Ant In to
Antenna Cable (Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
or
Use a 75 ohm (round) cable.
Use one of the connections below to
connect your TV to an external A/V
device.
We recommend using HDMI for the
highest picture quality.
HD connection (up to 1080p)
Using an HDMI Cable
HDMI OUT
HDMI Cable (Not Supplied)
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Very Good Connection
HD connection (up to 1080p)
Step 1: Install the Stand
Step 4: Run Plug & Play
Follow the steps below to connect the TV to the stand.
✎✎NOTE
xx Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
xx Make sure that at least two persons lift and move the LED TV.
xx Stand the product up and fasten the screws. If you fasten the screws with
the LED TV placed down, it may lean to one side.
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the MENU button. To turn on your TV, press the POWER
button on the remote or on the TV. To run Plug & Play, follow these steps:
the language for the On Screen
Display (OSD), and then press the
ENTERE button.
1 Insert the stand body into the stand
base.
2 Screw the stand base to the stand 3 Slide the TV onto the stand
body.
body.
3 Select Antenna Source to
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
Select Language of the OSD.
Menu Language
:
Good Connection
English
Français
U Move E Enter
:
Digital Cable System
:
Analog Cable System
:
Audio Cable
(Not Supplied)
Cable
Auto
Search
memorize. If Antenna Source is
Cable or Auto, you must select
U Move E Enter
your cable system type. After
selecting source, select Search; then press the ENTERE button on your
remote.
Connecting an audio device (Home Theater, etc.)
Connecting a PC
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connect your TV to a PC to use it as a Monitor.
Analog Audio connection
1 Connect the Guide Stand to the
Stand using four screws (M4 X
L12) as shown
s
s
s
Stand
AUDIO OUT
Digital Audio connection
2 With your TV upright, connect the
TV to the Stand as shown.
3 Fasten three screws (M4 X L8) at
position 1, and then fasten three
screws (M4 X L8) at position 2.
s
s
s
s
Front
s
s
s
s
Rear
1
OPTICAL
7 Select the time zone in which you live, and then press the ENTERE button.
8 After the time zone screen, The connection method for best HD screen
Using a D-Sub Cable
Audio Cable
(Not Supplied)
AUDIO OUT
Analog Audio connection
D-Sub Cable (Not Supplied)
Amplifier / DVD home theater
Audio Cable (Not Supplied)
AUDIO IN
Using an EX-Link Cable Connection
Digital Audio connection
s
9 The Enjoy your TV. screen appears. Then press the ENTERE button.
If You Want to Rerun Plug & Play
1. Press the SOURCE button on your remote, then select TV mode.
PC OUT
Using an Audio Cable
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
s
2
Digital Audio System
Optical Cable (Not Supplied)
ENTERE button.
Rear
Audio Cable
(Not Supplied)
Using an Optical Cable
5 After the TV has memorized the channels, choose the Clock Mode. Select
6 Select the daylight savings time setting: Off or On, and then press the
s
Using a HDMI to DVI Cable
DVI OUT
✎✎ If you select Manual, the clock setting screen appears.
s
HDMI to DVI Cable
(Not Supplied)
headphone
minutes.
Auto if you have a digital channel in your area. Select Manual if you don’t, or
if you have a cable or satellite box. When done, press the ENTERE button.
HD connection
Using a Headphone
4 The TV memorizes the available channels. This process can take up to 45
Guide Stand
DVD / Blu-ray player / Cable Box / Satellite
receiver / VCR
Device
AUDIO OUT
VIDEO OUT
Air
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
Screws (M4 X L12)
Using an Audio/Video Cable
DVD / Blu-ray player / Cable Box / Satellite receiver / VCR
DVD / Blu-ray player
COMPONENT OUT
AUDIO OUT
Component Cable
(Not Supplied)
✎✎If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Top view
Audio/Video connection (480i only)
Using a Component Cable
Plug & Play
Anrenna Source
Lowest Quality Connection
Component connection (up to 1080p)
Español
what kind of cable system you have, contact your cable company.
UN26C4000
Device
AUDIO OUT
Video Cable (Not Supplied)
✎✎Most cable systems are Standard (STD) systems, If you are not sure about
LOCK
C
DVI OUT
Plug & Play
2 Select Home Use, and then
press the ENTERE button. If
you select Store Demo, the TV
will reset your picture and audio
settings every 30 minutes.
Using a HDMI to DVI Cable
HDMI to DVI Cable (Not Supplied)
1 Using your remote control, select
UN19C4000, UN22C4000, UN22C4010
REELLE
EAAASSE
E
DVD / Blu-ray player
/ HD Cable Box / HD
Satellite receiver (STB)
Device
Available Devices: External devices that support EX-Link.
Using an Optical Cable
Digital Audio System
EX-LINK: Connector for service only.
Optical Cable (Not Supplied)
OPTICAL
2. Press the MENU button on your remote to display the menu.
3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE
button.
4. Press ENTERE again to select Plug & Play.
[QSG]BN68-02628A-01Eng.indd 1
2010-09-03 오후 6:46:05
Step 5: Remote Control
Changing Channels and Adjusting the Volume
Remote Control Buttons and Functions
✎✎This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons.
PRE-CH
Change the channels by pressing the Channel button on the remote.
Adjust the volume by pressing the Volume button
on the remote.
✎✎If your TV is attached to a cable or satellite box, change the channel using
the box’s remote.
CH LIST
MENU
MEDIA.P
Turns the TV on and off.
POWER
SOURCE
✎✎You can also change the channels by pressing the z
TOOLS
Displays and selects the available video sources.
Press to directly access channels.
Press to select additional channels
(digital) being broadcasted by the same
station. For example, to select channel
“54-3”, press “54”, then press “-” and “3”.
PRE-CH
Changes channels.
CH LIST
Brings up the OSD.
Displays the channel list on the screen.
MENU
Displays Favorite Channel Lists on the screen.
Displays Media Play.
MEDIA.P
FAV.CH
Quickly select frequently used functions.
TOOLS
INFO
Displays information on the TV screen.
EXIT
Selects the on-screen menu items and changes the values
seen on the menu.
Exits the menu.
Returns to the previous menu.
Buttons used in the Channel list, Media Play menu,
etc.
RETURN
A
B
C
SOURCE
EXIT
SLEEP
MTS
P.MODE
P.SIZE
CC
Use these buttons in Media Play and Anynet+ modes.
(�: Controls recording for Samsung recorders that have
the Anynet+ feature)
S.MODE: Press to select the sound mode.
SLEEP: Automatically shuts off the TV at a preset time.
MTS: Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
P.MODE: Press to select the picture mode.
P.SIZE: Selects the picture size.
CC: Controls the caption decoder.
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote upward as shown in the
figure to the right.
2. Install two AAA batteries.
✎✎ Make sure to match the + and - ends of the batteries to
the diagram in the battery compartment.
PRE-CH
Viewing the On Screen Menus
To view the On Screen Menus, follow these steps:
1. With the power on, press the MENU button on
your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel, Setup,
Input, Application, and Support.
Your TV has three preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
To change the Picture mode, press the P.MODE button on your remote. The first
time you press it, your TV displays the current setting. Thereafter, each time you
press the P.MODE button, you change the mode of the picture on the screen.
The Picture Modes are listed and described in the table below:
Mode
Dynamic
CH LIST
MENU
MEDIA.P
TOOLS
FAV.CH
CH LIST
MENU
Movie
Description
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
For a bright, detailed picture in a normally lit room.
For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
1. With the TV on, press the TOOLS button on your remote. The Tools menu
appears.
MEDIA.P
FAV.CH
INFO
2. Using the ▲ or ▼ on your remote, select Picture Mode.
TOOLS
INFO
RETURN
EXIT
3. On the Picture mode menu, use the ◄ or ► on your remote to select the
Picture Mode you want.
2. Press the ▲ or ▼ button on your remote to select a menu option, and then
press the ENTERE button.
4. Press the EXIT button to exit the menu.
3. When done using the menu, press the EXIT button on your remote to exit.
Setting the Clock
RETURN
A
B
C
EXIT
D
S.MODE
A
B SLEEPC
MTS
D
P.MODE
S.MODE
P.SIZE
SLEEP
CC
MTS
P.MODE
P.SIZE
CC
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.SIZE button on your remote. The first time
you press it, your TV displays the current setting. Thereafter, each time you press
the P.SIZE button, you change the size of the picture on the screen.
The following sizes are available:
Before you can use your TV’s On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1. Turn on your TV, press the MENU button on your remote, then select Setup →
Time.
2. Select Clock Mode, and then press the ENTERE button.
3. Choose Auto or Manual.
xx If you select Auto, the current time will be set automatically using the time
from a digital channel.
xx If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
4. Press the RETURN button on your remote when done.
16:9 Wide screen
Install the Batteries into the Remote
Changing the Picture Mode
Standard
Changing the Screen Size
D
S.MODE
3. Replace the cover.
POWER
RETURN
Returns to the previous channel.
Cuts off the sound temporarily.
Adjusts the volume.
INFO
To watch a movie on your Blu-ray player or watch
POWER
SOURCE
your favorite TV show, you must select the correct
A
B
C
D
HDMI
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
S.MODE
SLEEP
MTS
input. Sources can be connected to your TV through
HDMI
P.SIZE
P.MODE
the HDMI, DVI, Component, Composite, or D-sub connections, or through theCC
Antenna or Cable In connections.
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the SOURCE button on your remote. Each time
you press the SOURCE button, you change to a different source.
PRE-CH
HDMI
Selects the HDMI mode directly.
Selecting a Source
FAV.CH
button on the front panel of your TV and adjust the volume by pressing the y button.
Zoom 1
4:3 Standard screen
Zoom 2
Wide Fit
Screen Fit
✎✎Screen Fit displays the full image without any cut-off when HDMI (720p /
1080i / 1080p) or Component (1080i / 1080p) signals are inputted.
Connecting a USB Device for Media Play
You can enjoy photo,
music, and movie files
stored on a USB device
by connecting it to the TV
and using the Media Play
feature. For Media Play
operating instructions,
please see your Owner’s
Manual.
MediaPlay
Videos
SUM
Device
Device Mode E Enter R Return
1. Turn on your TV.
2. Connect a USB device containing photo, music and/or movie files to the USB
1 or USB2 (HDD) jack on the side of the TV.
3. When the Input selection screen appears, press the ENTERE button on your
remote to select Media Play (USB).
BN68-02628A-01
[QSG]BN68-02628A-01Eng.indd 2
2010-09-03 오후 6:46:08