quickstart guide
TSW-730
1
7” Room Scheduling Touch Screen
2
Change the Button Inserts or Button Covers
The Crestron® TSW-730 Touch Screen ships with 10 “hard key” push buttons for
quick access to commonly used functions. Optional, custom engravable button
covers are available (TSW-730-BTNO-[B, W]-S and custom engraving sold
separately). For a clean appearance, either column of buttons may be removed
and covered using the no-button covers provided.
To change the inserts or covers, use the following procedure:
1.
Insert a small, slot head screwdriver into the appropriate hole on the bottom of
the touch screen to release its cover. Refer to the following illustration.
Insertion Points for Button Cover Releases
Install the Touch Screen
The TSW730 touch screen installs simply and easily into a standard electrical box or
onto virtually any flat surface.
3.
Carefully position the front of the touch screen over the back panel and gently
snap it into place.
A tabletop enclosure, the TSW-730-TTK and swivel mount, SMK-4SM/730 are also
available (both sold separately). For mounting onto a flat surface, use the
TSW-730-MSMK Multi-Surface Mounting Kit (sold separately).
4.
Use two of the included #04-40 x 1/4” screws to secure the touch screen, as
shown in the following illustration:
The TSW-730 is supplied with screws for installation into an electrical box.
Mounting in a U.S. Electrical Box
a.
For standard applications, use the Phillips screws (2007152 or 2007160).
b.
For secure applications, use the security type Torx screws (2025311 or
2025312) along with the included Torx screwdriver bit (2025915).
Secure the Touch Screen
To mount the TSW-730 into a U.S. electrical box, use the following procedure:
1.
Insert screwdriver to release covers
2.
With the bottom of the cover released, gently remove it from the touch screen.
3.
If removing the button insert, after releasing and removing the button cover,
use a small slot head screwdriver to press and gently lift the button insert from
the touch screen. Refer to the following illustration for the press and lift points
on the button insert.
Insertion Point for Separation of Back Panel
Insert screwdriver to separate back of touch screen
2.
Touch Screen with Button Inserts
Insert a small slot head screwdriver into the hole shown in the following
illustration and gently separate the back of the touch screen.
Screws (2) #04-40 x 1/4”
Use the four included #06-32 x 1 x 1/2” screws (2031703) to attach the back
panel to the electrical box, as shown in the following illustration.
Mounting the Touch Screen into an Electrical Box
For standard applications: Phillips
(2007152 or 2007160)
For secure applications: security type Torx
(2025311 or 2025312)
U.S. Electrical Box
Use screwdriver
to release button insert
Gently place the new cover in position and press it into place.
Touch Screen with No-Button Covers
Screws (4) #06-32 x 1 1/2”
(2031703)
TSW-730
1
For regulatory compliance information, refer to Doc. 7413.
www.crestron.com
QUICKSTART DOC. 7412C (2034621, Sheet 1 of 2)
04.14
Specifications subject to
change without notice.
888.273.7876
201.767.3400
TSW-730
4.
quickstart guide
TSW-730
2
7” Room Scheduling Touch Screen
3
Install the Touch Screen (Continued)
Mounting in a U.K. Electrical Box
To mount the TSW-730 into a U.K. electrical box, use the following procedure:
1.
2.
Insert a small slot head screwdriver into the hold shown in the illustration in step 1,
in the middle column on the previous page, to gently separate the back of the
touch screen.
4
Hardware Hookup
Establish Communication
Make the necessary connections as called out in the illustration below.
Apply power after all connections have been made.
Use Crestron Toolbox™ for communicating with the TSW-730; refer to the Crestron
Toolbox help file for details.
When making connections to the TSW-730, use Crestron power supplies for
Crestron equipment.
There is a single method of communication: TCP/IP communication.
Hardware Connections for the TSW-730
Ethernet Communication
Use the two included #4B x 3/4” screws (2019088) to attach the back panel to
the electrical box, as shown in the following illustration.
N
LA
Power
Injector
TSW-730
E
PO
PoE
Mounting the Touch Screen into a U.K. Electrical Box
4
3
2
1
ink
Upl
ON itch
TR et Sw
ES r Ethern
CRPower ove
E-5
-PO
-SW
CEN
U.K. Electrical Box
PC Running
Crestron Toolbox
DC
48V
er
Pow
ON
ES
TR
CR
120 Volts
The TSW-730 connects to PC via Ethernet:
Occupancy Sensor Input:
From Room Occupancy Sensor
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN
1.
Use the Device Discovery Tool (click the
icon) in Crestron Toolbox to
detect all Ethernet devices on the network and their IP configuration. The
tool is available in Toolbox version 1.15.143 or later.
2.
Click on the TSW-730 to display information about the device.
NOTE: To prevent overheating, do not operate this product in an area that
exceeds the environmental temperature range listed in the table of
specifications. Refer to section ➑ “Specifications” on page 4 for details.
Screws (2) 4B, 3/4”
(2019088)
TSW-730
Carefully position the front of the touch screen over the back panel and
gently snap it into place.
4.
Use two of the included #04-40 x 1/4” screws to secure the touch screen, as
shown in the illustration in step 3, in the last column on the previous page:
a.
For standard applications, use the Phillips screws (2007152 or
2007160).
b.
For secure applications, use the security type Torx screws (2025311 or
2025312) along with the included Torx screwdriver bit (2025915).
TSW-730
2
3.
For regulatory compliance information, refer to Doc. 7413.
www.crestron.com
QUICKSTART DOC. 7412C (2034621, Sheet 1 of 2)
04.14
Specifications subject to
change without notice.
888.273.7876
201.767.3400
quickstart guide
TSW-730
5
7” Room Scheduling Touch Screen
6
Configure the Touch Screen
7
Dimensions
TSW-730 Overall Dimensions (Front, Side and Rear Views)
NOTE: The only connection required to configure the touch screen is power.
Refer to section ➌ “Hardware Hookup” on page 2 for details.
Along with its Occupancy Sensor Input (refer to section ➑ “Specifications” for
details), the TSW-730 has a LAN PoE port.
8.76 in
(223 mm)
NOTE: The TSW-730 can take up to 120 seconds to boot to a display after initial
power up.
Pinout Reference
LAN PoE
Pin 1 Pin 8
The main setup menu is the starting point for configuring the TSW-730. To enter the
setup menu, touch the screen while applying power to the unit.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
touch screen defaults to the main setup menu.
Yellow
LED
4.75 in
(121 mm)
PIN
1
2
3
4
5
6
7
8
The setup screens enable basic configuration procedures prior to regular operation of
the touch screen.
During regular operation of the touch screen, there are two ways to activate the setup
functions:
1.
Place a button on the project main page and assign the reserved join number
(17242) that activates setup.
2.
Press hard keys 1, 2, 3, and 4, on the left side of the touch screen display, in
sequence twice (press 1, 2, 3, 4, 1, 2, 3, 4) within a 5 second period.
0.86 in
(22 mm)
1.25 in
(32 mm)
0.39 in
(10 mm)
Green
LED
DESCRIPTION
TX+ / V(A)TX- / V(A)RX+ / V(A)+
NC / V(B)+
NC / V(B)+
RX- / V(A)+
NC / V(B)NC / V(B)-
Button Numbering
1
2
3
4
7.30 in
(186 mm)
The main setup menu is displayed.
1.82 in
(46 mm)
3.25 in
(83 mm)
3.80 in
(97 mm)
NOTE: For details on configuring the TSW-730, refer to the TSW-730 Configuration
Guide (Doc. 7414) at www.crestron.com/manuals.
3
For regulatory compliance information, refer to Doc. 7413.
www.crestron.com
QUICKSTART DOC. 7412C (2034621, Sheet 2 of 2)
04.14
Specifications subject to
change without notice.
888.273.7876
201.767.3400
TSW-730
4.74 in
(121 mm)
quickstart guide
TSW-730
8
7” Room Scheduling Touch Screen
Specifications
Touch Screen Display
Connectors (Continued)
Display Type: TFT Active matrix color LCD
Size: 7 inch (178 mm) diagonal
Aspect Ratio: 15:9 WVGA
Resolution: 800 x 480 pixels
Brightness: 300 nits (cd/m2)
Contrast: 350:1
Color Depth: 18-bit, 262k colors
Illumination: Edgelit LED
Viewing Angle: ±70° horizontal, ±65° vertical
Touch Screen: Projected Capacitive
Occupancy Sensor Input: (4) captive screw terminals comprising (2) voltage sensing inputs (referenced to GND) with 24 Vdc
power output3;
Input Voltage Range: 0-30 Vdc
Sensing Threshold: •18Vdc Vdc active, ”10Vdc inactive
Maximum DC Load: 4 watts @ 24 Vdc, provides operating power for up to (4) Crestron GLS Series occupancy sensors3
Power Requirements
Power over Ethernet: IEEE 802.3at Type 2 PoE+ powered device
x
16 watts if using an 802.3at Type 2 PSE (Power Sourcing Equipment) with LLDP advanced power management
x
Class 4 (25.5. W) if using an 802.3at Type 2 PSE without LLDP
x
Class 3 (12.95 W) if using an 802.3af (or 802.3at Type 1) PSE (no power available for external occupancy sensors)3
Buttons
Hard Keys: (10) Optional push buttons, translucent backlit, for scheduling functions (default) or programmable for any function
Feedback/Backlight: (1) red and (1) green LED per hard key, for room status indication (default) or programmable for custom
feedback and backlighting
Reset: (1) Recessed push button behind pinhole for hardware reset
Proximity Sensor
Environmental
Temperature: 32° to 112° F (0° to 45° C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 35 Btu/h
Enclosure
Type: Active infrared beam and receiver
Range: 3-4 feet
Wakes the touch screen and backlight
Construction: Plastic, smooth black or white finish
Front Bezel: Plastic, hard buttons installed with pre-labeled button covers, custom engraving sold separately,
“no-button” covers also included
Mounting: Surface mount over a 2-gang electrical box or plaster ring, 2-gang UK (BS 4662) electrical box or rectangular cutout;
choice of standard or security screws provided; optional multi-surface and tabletop mounting kits sold separately
Memory
LPDDR2 RAM: 1 GB
Flash: 4 GB
Maximum Project Size: 512 MB
Dimensions
Height: 4.75 in (121 mm)
Width: 8.76 in (223 mm)
Depth: 1.25 in (32 mm)
Graphics Engine
Supports Smart Graphics™ 1
Weight
Crestron Fusion® Language Support
19 oz (518 g)
Chinese (Simplified), Chinese (Traditional), Dutch (Netherlands), English (US), English (UK), French, German, Italian, Japanese,
Russian, Spanish
Communications
Video2
1.
2.
3.
Supports Smart Graphics only. Not compatible with “traditional” UI projects.
Enabled through custom programming. Not used for typical room scheduling applications.
To supply 24 Vdc power for external occupancy sensors via the Occupancy Sensor input port, the TSW-730 must be
powered using an IEEE 802.3at Type 2 PoE+ PSE. The TSW-730 may be powered by an 802.3af or 802.3at Type 1 PoE
PSE if no occupancy sensors are connected or if the occupancy sensors are not powered by the TSW-730.
Streaming Formats: H.264 (MPEG-4 part 10 AVC), MJPEG
Audio2
Features: Built-in microphone and speakers, Rava™ SIP Intercom
Audio Feedback Formats: MP3
The specific patents that cover Crestron products are listed at patents.crestron.com.
Connectors
Crestron, the Crestron logo, Crestron Fusion, Rava, and Smart Graphics are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
LAN PoE: (1) 8-wire RJ-45 with (2) LED indicators
10BASE-T/100BASE-TX Ethernet port, Power over Ethernet Plus compliant3
Green and yellow LEDs indicate Ethernet port status
4
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
For regulatory compliance information, refer to Doc. 7413.
www.crestron.com
QUICKSTART DOC. 7412C (2034621, Sheet 2 of 2)
04.14
Specifications subject to
change without notice.
888.273.7876
201.767.3400
TSW-730
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3af and 802.3at
compliant
NOTES