Cisco WRP400 User guide

USER GUIDE
Wireless-G
Broadband Router
with 2 Phone Ports
Model No: WRP400
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Linksys
www.linksys.com
Linksys International
www.linksys.com/international
Glossary
www.linksys.com/glossary
Network Security
www.linksys.com/security
Copyright and Trademarks
Linksys is a registered trademark or
trademark of Cisco Systems, Inc. and/
or its affiliates in the U.S. and certain
other countries. Copyright © 2007
Cisco Systems, Inc. All rights reserved.
Other brands and product names are
trademarks or registered trademarks
of their respective holders.
Wireless-G Broadband Router with 2 Phone Ports
Table of Contents
Chapter 1: Product Overview
4
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Placement Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Wireless Security Checklist
7
General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3: Advanced Configuration
8
Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup > DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setup > MAC Address Clone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wireless > Wireless MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Applications and Gaming > Single Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . 20
Applications and Gaming > Port Range Forward . . . . . . . . . . . . . . . . . . . . . . . . . 21
Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .22
Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Administration > Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Administration > Config Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Access to the Voice Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Voice > Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Voice > System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Voice > User 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Voice > Admin Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Wireless-G Broadband Router with 2 Phone Ports
ii
Table of Contents
Chapter 4: Interactive Voice Response Menu
34
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Menu Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appendix A: Troubleshooting
35
Appendix B: Specifications
37
Appendix C: Warranty Information
39
Appendix D: Regulatory Information
40
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Safety Notices and Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . . 41
Telepermit Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) . . 42
CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Technical Documents on www.linksys.com/international . . . . . . . . . . . . . . . . . . . . 44
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Wireless-G Broadband Router with 2 Phone Ports
iii
Product Overview
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Linksys Wireless-G Broadband
Router with 2 Phone Ports. The Router lets you access
the Internet via a wireless connection or through one of
its four switched ports. You can also use the Router to
share resources such as computers, printers and files. The
built‑in phone adapter enables Voice-over-IP (VoIP) calls
even while you are using the Internet.
Front Panel
Wireless (Green) The Wireless LED lights up
when the wireless feature is enabled. It flashes
when the Router is actively sending or receiving
data over the network.
Ethernet 1-4 (Green) These numbered LEDs,
corresponding with the numbered ports on the
Router’s back panel, serve two purposes. If the
LED is solidly lit, the Router is connected to a
device through that port. It flashes to indicate
network activity over that port.
Internet (Green) The Internet LED lights up
and stays on when there is a connection made
through the Internet port. It flashes to indicate
network activity over the Internet port.
Back Panel
USB The USB port is reserved for future use.
Wi-Fi Protected Setup (White/Orange) If you
have client devices, such as wireless adapters,
that support Wi-Fi Protected Setup, then you
can use Wi-Fi Protected Setup to automatically
configure wireless security for your wireless
network(s).
To use Wi-Fi Protected Setup, refer to your
wireless adapter’s documentation.
The Wi-Fi Protected Setup button lights up
white and stays on while wireless security is
enabled on your wireless network(s). The button
flashes orange if there is an error during the
Wi‑Fi Protected Setup process. Make sure the
client device supports Wi-Fi Protected Setup,
and then try again.
Internet The Internet port is where you will
connect your cable or DSL Internet connection.
Phone 1-2 The Phone ports connect standard
analog telephones to the Router.
Ethernet 1, 2, 3, 4 These Ethernet ports (1, 2, 3,
4) connect the Router to wired computers and
other Ethernet network devices.
Power The Power port is where you will
connect the power adapter.
Power (Green/Red) The Power LED lights up
green and stays on while the Router is powered
on. When the Router goes through its selfdiagnostic mode during every boot-up, the LED
will flash. When the diagnostic is complete, it
will be solidly lit green. If the LED lights up red,
make sure the correct power adapter is used.
If the LED remains red, contact your Internet
Service Provider (ISP) or Internet Telephony
Service Provider (ITSP) for support.
Phone 1-2 (Green) The Phone 1 or 2 LED lights
up and stays on when an active line is registered
to the corresponding port on the Router’s back
panel. The LED slowly flashes when voicemail
messages are waiting.
Wireless-G Broadband Router with 2 Phone Ports
Product Overview
Chapter 1
Side Panel
Vertical Placement
The Router has a stand on the panel opposite to the
antenna. Rotate the stand 90 degrees, and place the
Router on a level surface near an electrical outlet.
Reset There are two ways to reset the Router’s
factory defaults. Either press and hold the Reset
button for approximately ten seconds, or restore
the defaults from the Administration > Factory
Defaults screen of the Router’s web-based
utility. (The Factory Defaults screen allows
you to restore the Router and voice defaults
separately.)
NOTE: Restoring the voice defaults
may require your login (the default
user name and password are admin). If
the defaults do not work, contact your
ITSP for more information.
Stand To place the Router in a vertical position,
rotate the stand 90 degrees.
Placement Positions
There are three ways to physically install the Router. The
first way is to place the Router horizontally on a surface.
The second way is to stand the Router vertically on a
surface. The third way is to mount the Router on a wall.
Horizontal Placement
The Router has four rubber feet on its bottom panel. Place
the Router on a level surface near an electrical outlet.
Wall-Mounting Placement
The Router has four wall-mount slots on its back panel.
The distance between two adjacent slots is 60 mm
(2.36 inches).
Two screws are needed to mount the Router.
4-5 mm
1-1.5 mm
2.5-3.0 mm
Suggested Mounting Hardware
†Note: Mounting hardware illustrations are not
true to scale.
NOTE: Linksys is not responsible for damages
incurred by insecure wall-mounting hardware.
Follow these instructions:
1. Determine where you want to mount the Router. Make
sure that the wall you use is smooth, flat, dry, and
sturdy. Also make sure the location is within reach of
an electrical outlet.
2. Drill two holes into the wall. Make sure the holes are
60 mm (2.36 inches) apart.
Wireless-G Broadband Router with 2 Phone Ports
Product Overview
Chapter 1
3. Insert a screw into each hole and leave 3 mm
(0.12 inches) of its head exposed.
4. Maneuver the Router so two of the wall-mount slots
line up with the two screws.
5. Place the wall-mount slots over the screws and slide
the Router down until the screws fit snugly into the
wall-mount slots.
60 mm
Print this page at 100% size. Cut along
the dotted line, and place on the wall
to drill precise spacing.
Wall Mounting Template
Wireless-G Broadband Router with 2 Phone Ports
Wireless Security Checklist
Chapter 2
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This is
the name of your wireless network, and can be up to 32
characters in length. To distinguish your wireless network
from other wireless networks that may exist around you,
you should change the default wireless network name to
something easily recognizable, but do not use personal
information (such as your Social Security number) because
this information may be available for anyone to see when
browsing for wireless networks.
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalency Privacy (WEP) offer different levels of security
for wireless communication.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
•
Password protect all computers on the network and
individually password protect sensitive files.
•
Change passwords on a regular basis.
•
Install anti-virus software and personal firewall
software.
•
Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
2. Change the default password
For wireless products such as access points and routers,
you will be asked for a password when you want to change
their settings. These devices have a default password set
by the factory. The Linksys default password is admin.
Hackers know these defaults and may try to use them
to access your wireless device and change your network
settings. To thwart any unauthorized changes, customize
the device’s password so it will be hard to guess.
3. Enable MAC address filtering
Linksys routers give you the ability to enable Media Access
Control (MAC) address filtering. The MAC address is a
unique series of numbers and letters assigned to every
networking device. With MAC address filtering enabled,
wireless network access is provided solely for wireless
devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home
so that only those computers can access your wireless
network.
Wireless-G Broadband Router with 2 Phone Ports
Additional Security Tips
•
Keep wireless routers, access points, or gateways away
from exterior walls and windows.
•
Turn wireless routers, access points, or gateways
off when they are not being used (at night, during
vacations).
•
Use strong passphrases that are at least eight characters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
WEB: For more information on wireless
security, visit www.linksys.com/security
Advanced Configuration
Chapter 3
Chapter 3:
Advanced Configuration
After setting up the Router with the Setup Wizard (located
on the CD-ROM), the Router will be ready for use. However,
if you’d like to change its advanced settings, use the
Router’s web-based utility. This chapter describes each
web page of the utility and each page’s key functions. You
can access the utility via a web browser on a computer
connected to the Router.
The web-based utility has these main tabs: Setup, Wireless,
Security, Access Restrictions, Applications & Gaming,
Administration, Status, and Voice. Additional tabs will be
available after you click one of the main tabs.
NOTE: When first installing the Router, you
should use the Setup Wizard on the Setup CDROM. If you want to configure advanced settings,
use this chapter to learn about the web-based
utility.
Setup > Basic Setup
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on
your computer, and enter the Router’s default IP address,
192.168.15.1, in the Address field. Then press Enter.
NOTE: If you place the Router behind a primary
router with the IP address of 192.168.15.1, then
the Router will automatically assume a new
default IP address, 192.168.16.1.
A login screen appears. The first time you open the
web-based utility, use the default user name and
password, admin. (You can set a new password from the
Administration tab’s Management screen.) Click OK to
continue.
Internet Setup
The Internet Setup section configures the Router to your
Internet connection. Most of this information can be
obtained through your Internet Service Provider (ISP).
Internet Connection Type
Select the type of Internet connection your ISP provides
from the drop-down menu. These are the available types:
•
Automatic Configuration - DHCP
•
Static IP
•
PPPoE
•
PPTP
•
L2TP
•
Telstra Cable
Automatic Configuration - DHCP
By default, the Router’s Internet Connection Type is set
to Automatic Configuration - DHCP, which should be
kept only if your ISP supports DHCP or you are connecting
through a dynamic IP address. (This option usually applies
to cable connections.)
Login Screen
Setup > Basic Setup
Internet Connection Type > Automatic Configuration - DHCP
The first screen that appears is the Basic Setup screen. This
allows you to change the Router’s general settings.
Wireless-G Broadband Router with 2 Phone Ports
Advanced Configuration
Chapter 3
Static IP
If you are required to use a permanent IP address to
connect to the Internet, select Static IP.
Keep Alive: Redial Period If you select this option,
the Router will periodically check your Internet
connection. If you are disconnected, then the Router
will automatically re-establish your connection. To use
this option, select Keep Alive. In the Redial Period field,
you specify how often you want the Router to check
the Internet connection. The default Redial Period is
30 seconds.
PPTP
Internet Connection Type > Static IP
Point-to-Point Tunneling Protocol (PPTP) is a service that
applies to connections in Europe only.
Internet IP Address This is the Router’s IP address, when
seen from the Internet. Your ISP will provide you with the
IP address you need to specify here.
Subnet Mask This is the Router’s Subnet Mask, as seen
by users on the Internet (including your ISP). Your ISP will
provide you with the Subnet Mask.
Default Gateway Your ISP will provide you with the IP
address of the ISP server.
DNS 1-3 Your ISP will provide you with at least one DNS
(Domain Name System) server IP address.
PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol
over Ethernet) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoE. If they do, you will have
to enable PPPoE.
Internet Connection Type > PPTP
Internet IP Address This is the Router’s IP address, as
seen from the Internet. Enter the IP address provided by
your ISP.
Subnet Mask This is the Router’s Subnet Mask, as seen
by users on the Internet (including your ISP). Enter the
Subnet Mask provided by your ISP.
Default Gateway Enter the IP address of the ISP server,
which is provided by your ISP.
User Name and Password Enter the User Name and
Password provided by your ISP.
Internet Connection Type > PPPoE
User Name and Password Enter the User Name and
Password provided by your ISP.
Service Name (Optional) If provided by your ISP, enter
the Service Name.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 5 minutes.
Wireless-G Broadband Router with 2 Phone Ports
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 5 minutes.
Keep Alive: Redial Period If you select this option, the
Router will periodically check your Internet connection. If
you are disconnected, then the Router will automatically
re-establish your connection. To use this option, select
Keep Alive. In the Redial Period field, you specify how often
you want the Router to check the Internet connection. The
default value is 30 seconds.
Advanced Configuration
Chapter 3
L2TP
L2TP is a service that applies to connections in Europe and
Israel.
Internet Connection Type > L2TP
Server IP Address This is the IP address of the L2TP
Server. Enter the IP address provided by your ISP.
User Name and Password Enter the User Name and
Password provided by your ISP.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 5 minutes.
Keep Alive: Redial Period If you select this option,
the Router will periodically check your Internet
connection. If you are disconnected, then the Router
will automatically re-establish your connection. To use
this option, select Keep Alive. In the Redial Period field,
you specify how often you want the Router to check
the Internet connection. The default Redial Period is
30 seconds.
Telstra Cable
Telstra Cable is a service used in Australia only.
your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is 5 minutes.
Keep Alive: Redial Period If you select this option,
the Router will periodically check your Internet
connection. If you are disconnected, then the Router
will automatically re-establish your connection. To use
this option, select Keep Alive. In the Redial Period field,
you specify how often you want the Router to check
the Internet connection. The default Redial Period is
30 seconds.
Optional Settings
Some of these settings may be required by your ISP. Verify
with your ISP before making any changes.
Optional Settings
Host Name and Domain Name These fields allow you to
supply a host and domain name for the Router. Some ISPs,
usually cable ISPs, require these names as identification.
You may have to check with your ISP to see if your
broadband Internet service has been configured with a
host and domain name. In most cases, leaving these fields
blank will work.
MTU MTU is the Maximum Transmission Unit. It specifies
the largest packet size permitted for Internet transmission.
Select Manual if you want to manually enter the largest
packet size that is transmitted. To have the Router select
the best MTU for your Internet connection, keep the
default setting, Auto.
Size When Manual is selected in the MTU field, this option
is enabled. Leave this value in the 576 to 1500 range. The
default size depends on the Internet Connection Type:
•
DHCP or Static IP: 1500
•
PPPoE: 1492
Internet Connection Type > Telstra Cable
•
PPTP or L2TP: 1460
Heart Beat Server This is the IP address of the Heart Beat
Server. Enter the IP address provided by your ISP.
•
Telstra Cable: 1500
User Name and Password Enter the User Name and
Password provided by your ISP.
Connect on Demand: Max Idle Time You can configure
the Router to cut the Internet connection after it has been
inactive for a specified period of time (Max Idle Time). If
Wireless-G Broadband Router with 2 Phone Ports
Network Setup
The Network Setup section changes the settings on the
network connected to the Router’s Ethernet ports. Wireless
setup is performed through the Wireless tab.
10
Advanced Configuration
Chapter 3
Router IP
This presents both the Router’s Local IP Address and
Subnet Mask as seen by your network.
Router IP
DHCP Server Setting
•
Select Clients from DHCP Table Click the Select
check box to reserve a client’s IP address. Then click
Add Clients.
•
Manually Adding Client To manually assign an IP
address, enter the client’s name in the Enter Client
Name field. Enter the IP address you want it to have in
the Assign IP Address field. Enter its MAC address in the
To This MAC Address field. Then click Add.
Clients Already Reserved
The settings allow you to configure the Router’s Dynamic
Host Configuration Protocol (DHCP) server function. The
Router can be used as a DHCP server for your network. A
DHCP server automatically assigns an IP address to each
computer on your network. If you choose to enable the
Router’s DHCP server option, make sure there is no other
DHCP server on your network.
A list of DHCP clients and their fixed local IP addresses
will be displayed at the bottom of the screen. If you
want to remove a client from this list, click Remove.
Click Save Settings to apply your changes, or click
Cancel Changes to cancel your changes. To view the
most up-to-date information, click Refresh. To exit this
screen, click Close.
Starting IP Address Enter a value for the DHCP server
to start with when issuing IP addresses. Because the
Router’s default IP address is 192.168.15.1, the Starting
IP Address must be 192.168.15.2 or greater, but smaller
than 192.168.15.253. The default Starting IP Address is
192.168.15.100.
DHCP Server Setting
DHCP Server DHCP is enabled by factory default. If you
already have a DHCP server on your network, or you don’t
want a DHCP server, then select Disabled (no other DHCP
features will be available).
DHCP Reservation Click this button if you want to assign
a fixed local IP address to a MAC address.
DHCP Reservation
You will see a list of DHCP clients with the following
information: Client Name, Interface, IP Address, and
MAC Address.
Maximum DHCP Users Enter the maximum number of
computers that you want the DHCP server to assign IP
addresses to. This number cannot be greater than 253.
The default is 50.
IP Address Range Displayed here is the range of available
IP addresses.
Client Lease Time The Client Lease Time is the amount
of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the
amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the time is up, the user will
be automatically assigned a new dynamic IP address. The
default is 0 minutes, which means one day.
Static DNS 1-3 The Domain Name System (DNS) is how the
Internet translates domain or website names into Internet
addresses or URLs. Enter at least one DNS server IP address,
which is provided by your ISP. If you wish to use another,
enter that IP address in one of these fields. You can enter up
to three DNS server IP addresses here. The Router will use
these for quicker access to functioning DNS servers.
WINS The Windows Internet Naming Service (WINS)
manages each PC’s interaction with the Internet. If you
use a WINS server, enter that server’s IP address here.
Otherwise, leave this blank.
Time Setting
DHCP Reservation
Wireless-G Broadband Router with 2 Phone Ports
Time Zone Select the time zone in which your network
functions from this drop-down menu.
11
Advanced Configuration
Chapter 3
Automatically adjust clock for daylight saving
changes Select this option if you want the Router to
automatically adjust for daylight saving time. This option
is enabled by default.
DynDNS.org
Time Server Address If you want to use the Router’s
default Network Time Protocol (NTP) server, keep the
default, Auto. If you want to specify the NTP server, select
Manual, and enter the URL or IP address of the NTP server
you want to use.
Resync Timer The timer controls how often the Router
resyncs with the NTP server. Enter the number of seconds
you want the interval to be, or keep the default, 3600
seconds.
Setup > DDNS > DynDNS
User Name Enter the User Name for your DDNS account.
Time Setting
Password Enter the Password for your DDNS account.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Host Name The is the DDNS URL assigned by the DDNS
service.
Setup > DDNS
System Select the DynDNS service you use: Dynamic,
Static, or Custom. The default selection is Dynamic.
The Router offers a Dynamic Domain Name System (DDNS)
feature. DDNS lets you assign a fixed host and domain
name to a dynamic Internet IP address. It is useful when
you are hosting your own website, FTP server, or other
server behind the Router.
Mail Exchange (Optional) Enter the address of your mail
exchange server, so e-mails to your DynDNS address go to
your mail server.
Before you can use this feature, you need to sign
up for DDNS service with a DDNS service provider,
www.dyndns.org or www.TZO.com. If you do not want to
use this feature, keep the default setting, Disabled.
DDNS
DDNS Service
If your DDNS service is provided by DynDNS.org, then
select DynDNS.org from the drop-down menu. If your
DDNS service is provided by TZO, then select TZO.com.
The features available on the DDNS screen will vary,
depending on which DDNS service provider you use.
Backup MX This feature allows the mail exchange server
to be a backup. To disable this feature, keep the default,
Disabled. To enable the feature, select Enabled. If you
are not sure which setting to select, keep the default,
Disabled.
Wildcard This setting enables or disables wildcards
for your host. For example, if your DDNS address is
myplace.dyndns.org and you enable wildcards, then
x.myplace.dyndns.org will work as well (x is the wildcard).
To disable wildcards, keep the default, Disabled. To enable
wildcards, select Enabled. If you are not sure which setting
to select, keep the default, Disabled.
Internet IP Address The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Status The status of the DDNS service connection is
displayed here.
Update To manually trigger an update, click this button.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless-G Broadband Router with 2 Phone Ports
12
Advanced Configuration
Chapter 3
Clone Your PC’s MAC Click this button to clone the MAC
address of the computer you are using.
TZO.com
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > Advanced Routing
This screen is used to set up the Router’s advanced
functions. Operating Mode allows you to select the
type(s) of advanced functions you use. Dynamic Routing
automatically adjusts how packets travel on your network.
Static Routing sets up a fixed route to another network
destination.
Setup > DDNS > TZO
E-mail Address, TZO Key, and Domain Name Enter the
settings of the account you set up with TZO.
Internet IP Address The Router’s Internet IP address is
displayed here. Because it is dynamic, it will change.
Status The status of the DDNS service connection is
displayed here.
Update To manually trigger an update, click this button.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Setup > MAC Address Clone
A MAC address is a 12-digit code assigned to a unique
piece of hardware for identification. Some ISPs will require
you to register a MAC address in order to access the
Internet. If you do not wish to re-register the MAC address
with your ISP, you may assign the MAC address you have
currently registered with your ISP to the Router with the
MAC Address Clone feature.
Setup > Advanced Routing
Advanced Routing
NAT
Enabled/Disabled If this Router is hosting your network’s
connection to the Internet, keep the default, Enabled. If
another router exists on your network, select Disabled.
When the NAT setting is disabled, dynamic routing will be
enabled.
Dynamic Routing (RIP)
Setup > MAC Address Clone
MAC Address Clone
Enabled/Disabled This feature enables the Router to
automatically adjust to physical changes in the network’s
layout and exchange routing tables with the other
router(s). The Router determines the network packets’
route based on the fewest number of hops between
the source and the destination. When the NAT setting is
enabled, the Dynamic Routing feature is automatically
disabled. When the NAT setting is disabled, this feature
is available. Select Enabled to use the Dynamic Routing
feature.
Enabled/Disabled To have the MAC address cloned,
select Enabled.
Static Routing
MAC Address Enter the MAC address registered with
your ISP here.
A static route is a pre-determined pathway that network
information must travel to reach a specific host or network.
Wireless-G Broadband Router with 2 Phone Ports
13
Advanced Configuration
Chapter 3
Enter the information described below to set up a new
static route.
Route Entries To set up a static route between the Router
and another network, select a number from the dropdown list. Click Delete This Entry to delete a static route.
Wireless > Basic Wireless Settings
The basic settings for wireless networking are set on this
screen.
Enter Route Name Enter a name for the Route here,
using a maximum of 25 alphanumeric characters.
Destination LAN IP The Destination LAN IP is the address
of the remote network or host to which you want to assign
a static route.
Subnet Mask The Subnet Mask determines which
portion of a Destination LAN IP address is the network
portion, and which portion is the host portion.
Gateway This is the IP address of the gateway device that
allows for contact between the Router and the remote
network or host.
Interface This interface tells you whether the Destination
LAN IP address is on the LAN and Wireless (Ethernet and
wireless networks) or the Internet (WAN).
Click Show Routing Table to view the static routes you
have already set up.
Wireless > Basic Wireless Settings
There are two ways to configure the Router’s wireless
network(s), manual and Wi-Fi Protected Setup. To manually
configure the wireless settings, use the Basic Wireless
Settings screen.
If you have client devices, such as wireless adapters, that
support Wi-Fi Protected Setup, then you can use Wi‑Fi
Protected Setup to automatically configure wireless
security for your wireless network(s). To use Wi-Fi Protected
Setup, refer to your wireless adapter’s documentation.
NOTE: If you have client devices that do not
support Wi-Fi Protected Setup, click the Wireless
Security tab. Note the security settings, and then
manually enter them on those devices.
Advanced Routing > Routing Table
Routing Table
For each route, the Destination LAN IP address, Subnet
Mask, Gateway, and Interface are displayed. Click
Refresh to update the information. Click Close to exit
this screen.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless Network
Network Mode From this drop-down menu, you can
select the wireless standards running on your network(s).
If you have Wireless-G and Wireless-B devices in your
network(s), keep the default setting, Mixed. If you have
only Wireless-G devices, select Wireless-G only. If you
have only Wireless-B devices, select Wireless-B only.
Wireless Channel Select the channel you want to use.
To allow the Router to select the best available wireless
channel, keep the default, Auto.
SSID1/2 The SSID is the network name shared among all
devices in a wireless network. The Router can support up
to two wireless networks. By default, one wireless network
is enabled, and you can create a second wireless network.
Wireless-G Broadband Router with 2 Phone Ports
14
Advanced Configuration
Chapter 3
Configure the following settings for each wireless
network:
•
Wireless Network Name (SSID) The default
wireless network uses this name: “linksys” followed
by the last four digits of the Router’s wireless MAC
address. To rename the default wireless network,
enter a unique Wireless Network Name, which is
case-sensitive and must not exceed 32 characters
(use any of the characters on the keyboard).
To create a second wireless network, enter a unique
Wireless Network Name in the SSID2 setting. (To
activate this network, select Network Enabled.)
Security Mode
Select the security method for your wireless network.
Proceed to the appropriate instructions. If you do not
want to use wireless security, keep the default, Disabled.
WPA Personal
NOTE: If you are using WPA, always remember
that each device in your wireless network MUST
use the same WPA method and shared key, or
else the network will not function properly.
NOTE: Your ISP or ITSP may control the SSID2
settings. Contact your ISP or ITSP for more
information.
•
SSID Broadcast Enabled When wireless clients
survey the local area for wireless networks to associate
with, they detect the SSID broadcast by the Router. If
you want to broadcast the SSID, keep the check box
selected. If you do not want to broadcast the SSID,
deselect the check box.
•
Network Enabled To enable the wireless network,
select the check box. To disable the wireless network,
deselect the check box.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Wireless Security
The Wireless Security screen configures the security
of your wireless network(s). The Router supports the
following wireless security mode options: WPA Personal,
WPA Enterprise, WPA2 Personal, WPA2 Enterprise, and
WEP. (WPA stands for Wi-Fi Protected Access, which is a
security standard stronger than WEP encryption. WEP
stands for Wired Equivalent Privacy.) These options
are briefly discussed here. For detailed instructions on
configuring wireless security for the Router, refer to
“Chapter 2: Wireless Security.”
Security Mode > WPA Personal
WPA Algorithms WPA supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm, TKIP or AES. The default is TKIP.
WPA Shared Key Enter a WPA Shared Key of 8-63
characters.
Group Key Renewal Enter a Group Key Renewal period,
which instructs the Router how often it should change the
encryption keys. The default is 3600 seconds.
WPA2 Personal
NOTE: If you used Wi-Fi Protected Setup to
configure your wireless network(s), then wireless
security has already been set up. Do not make
changes to the Wireless Security screen.
Wireless Security
Select a SSID Select the appropriate SSID. (If you enabled
the second wireless network on the Basic Wireless Settings
screen, then set up wireless security for each SSID.)
Security Mode > WPA2 Personal
WPA Algorithms WPA2 supports two encryption
methods, TKIP and AES, with dynamic encryption keys.
Select the type of algorithm, AES or TKIP + AES. The
default is TKIP + AES.
WPA Shared Key Enter a WPA Shared Key of 8-63
characters.
Wireless-G Broadband Router with 2 Phone Ports
15
Advanced Configuration
Chapter 3
Group Key Renewal Enter a Group Key Renewal period,
which instructs the Router how often it should change the
encryption keys. The default is 3600 seconds.
WPA Enterprise
This option features WPA used in coordination with a
RADIUS server. (RADIUS stands for Remote Authentication
Dial-In User Service. This option should only be used when
a RADIUS server is connected to the Router.)
Security Mode > WPA2 Enterprise
WPA Algorithms WPA2 supports two encryption
methods, TKIP and AES, with dynamic encryption keys.
Select the type of algorithm, AES or TKIP + AES. The
default is TKIP + AES.
RADIUS Server Address Enter the IP address of the
RADIUS server.
Security Mode > WPA Enterprise
WPA Algorithms WPA supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
type of algorithm, TKIP or AES. The default is TKIP.
RADIUS Server Address Enter the IP address of the
RADIUS server.
RADIUS Port Enter the port number of the RADIUS
server. The default value is 1812.
Shared Key Enter the key shared between the Router
and the server.
RADIUS Port Enter the port number of the RADIUS
server. The default value is 1812.
Shared Key Enter the key shared between the Router
and the server.
Key Renewal Timeout Enter a Key Renewal Timeout
period, which instructs the Router how often it should
change the encryption keys. The default is 3600 seconds.
WEP
WEP is a basic encryption method, which is not as secure
as WPA.
Key Renewal Timeout Enter a Key Renewal Timeout
period, which instructs the Router how often it should
change the encryption keys. The default is 3600 seconds.
WPA2 Enterprise
This option features WPA2 used in coordination with a
RADIUS server. (It should only be used when a RADIUS
server is connected to the Router.)
Security Mode > WEP
Encryption Select a level of WEP encryption, 64 bits 10
hex digits or 128 bits 26 hex digits. The default is 64 bits
10 hex digits.
Passphrase Enter a Passphrase to automatically generate
WEP keys. Then click Generate.
Wireless-G Broadband Router with 2 Phone Ports
16
Advanced Configuration
Chapter 3
Key 1-4 If you did not enter a Passphrase, enter the WEP
key(s) manually.
TX Key Select which TX (Transmit) Key to use. The default
is 1.
MAC Address Filter List
Wireless Client List Click this to open the Wireless Client
List screen.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses of
the wireless devices transmitting within your network’s radius.
Wireless Client List
Wireless Client List
This screen shows the online and offline devices of the
wireless network(s). The device information includes
Client Name, IP Address, MAC Address, and Status.
Select Save to MAC Address Filter List for any device
you want to add to the MAC Address Filter List. Then
click Add.
To retrieve the most up-to-date information, click
Refresh. To exit this screen and return to the Wireless
MAC Filter screen, click Close.
MAC 01-40 Enter the MAC addresses of the devices
whose wireless access you want to block or allow.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Advanced Wireless Settings
Wireless > Wireless MAC Filter
Wireless MAC Filter
Select a SSID Select the appropriate SSID. (If you enabled
the second wireless network on the Basic Wireless Settings
screen, then set up wireless MAC filtering for each SSID.)
The Advanced Wireless Settings screen is used to set up
the Router’s advanced wireless functions. These settings
should only be adjusted by an expert administrator as
incorrect settings can reduce wireless performance.
Wireless MAC Filter To filter wireless users by MAC address,
either permitting or blocking access, select Enabled. If you
do not wish to filter users by MAC address, keep the default
setting, Disabled.
Access Restriction
Prevent Select this to block wireless access by MAC
address. This button is selected by default.
Permit Select this to allow wireless access by MAC
address. This button is not selected by default.
Wireless-G Broadband Router with 2 Phone Ports
Wireless > Advanced Wireless Settings
17
Advanced Configuration
Chapter 3
Advanced Wireless
Security > Firewall
Authentication Type The default is set to Auto, which
allows either Open System or Shared Key authentication
to be used. With Open System authentication, the sender
and the recipient do NOT use a WEP key for authentication.
With Shared Key authentication, the sender and recipient
use a WEP key for authentication. Select Shared Key to
only use Shared Key authentication.
The Firewall screen is used to configure a firewall that can
filter out various types of unwanted traffic on the Router’s
local network.
Transmission Rate The rate of data transmission should
be set depending on the speed of your wireless network(s).
You can select from a range of transmission speeds, or you
can select Auto to have the Router automatically use the
fastest possible data rate and enable the Auto-Fallback
feature. Auto-Fallback will negotiate the best possible
connection speed between the Router and a wireless
client. The default is Auto.
CTS Protection Mode The Router will automatically
use CTS (Clear-To-Send) Protection Mode when your
Wireless‑G products are experiencing severe problems and
are not able to transmit to the Router in an environment
with heavy 802.11b traffic. This function boosts the
Router’s ability to catch all Wireless-G transmissions but
will severely decrease performance. The default is Auto.
Beacon Interval Enter a value between 1 and 65,535
milliseconds. The Beacon Interval value indicates the
frequency interval of the beacon. A beacon is a packet
broadcast by the Router to synchronize the wireless
network(s). The default value is 100.
DTIM Interval This value, between 1 and 255, indicates
the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing
clients of the next window for listening to broadcast
and multicast messages. When the Router has buffered
broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Its clients
hear the beacons and awaken to receive the broadcast
and multicast messages. The default value is 1.
RTS Threshold Should you encounter inconsistent data
flow, only minor reduction of the default value, 2347, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The Router sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of
2347.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless-G Broadband Router with 2 Phone Ports
Security > Firewall
Firewall
SPI Firewall Protection To use firewall protection, keep
the default, Enabled. To turn off firewall protection, select
Disabled.
Internet Filter
Filter Anonymous Internet Requests This feature
makes it more difficult for outside users to work their
way into your network. This feature is selected by default.
Deselect the feature to allow anonymous Internet
requests.
Filter Internet NAT Redirection This feature uses port
forwarding to block access to local servers from local
networked computers. Select this feature to filter Internet
NAT redirection. It is not selected by default.
Filter IDENT (Port 113) This feature keeps port 113 from
being scanned by devices outside of your local network.
This feature is selected by default. Deselect this feature to
disable it.
Web Filter
Proxy Use of WAN proxy servers may compromise the
Router’s security. Denying Proxy will disable access to any
WAN proxy servers. Select this feature to enable proxy
filtering. Deselect the feature to allow proxy access.
Java Java is a programming language for websites. If you
deny Java, you run the risk of not having access to Internet
sites created using this programming language. Select
this feature to enable Java filtering. Deselect the feature
to allow Java usage.
18
Advanced Configuration
Chapter 3
ActiveX ActiveX is a programming language for websites.
If you deny ActiveX, you run the risk of not having access to
Internet sites created using this programming language.
Select this feature to enable ActiveX filtering. Deselect the
feature to allow ActiveX usage.
Cookies A cookie is data stored on your computer and
used by Internet sites when you interact with them. Select
this feature to filter cookies. Deselect the feature to allow
cookie usage.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Security > VPN Passthrough
The VPN Passthrough screen allows you to enable VPN
tunnels using IPSec, PPTP, or L2TP protocols to pass through
the Router’s firewall.
Access Restrictions > Internet Access
Security > VPN Passthrough
VPN Passthrough
IPSec Passthrough Internet Protocol Security (IPSec) is
a suite of protocols used to implement secure exchange
of packets at the IP layer. To allow IPSec tunnels to pass
through the Router, keep the default, Enabled.
PPTP Passthrough Point-to-Point Tunneling Protocol
(PPTP) allows the Point-to-Point Protocol (PPP) to be
tunneled through an IP network. To allow PPTP tunnels to
pass through the Router, keep the default, Enabled.
L2TP Passthrough Layer 2 Tunneling Protocol is the
method used to enable Point-to-Point sessions via the
Internet on the Layer 2 level. To allow L2TP tunnels to pass
through the Router, keep the default, Enabled.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Internet Access Policy
Access Policy Access can be managed by a policy. Use the
settings on this screen to establish an access policy (after
Save Settings is clicked). Selecting a policy from the dropdown menu will display that policy’s settings. To delete a
policy, select that policy’s number and click Delete This
Policy. To view all the policies, click Summary.
Summary
The policies are listed with the following information:
No., Policy Name, Access, Days, Time of Day, and status
(Enabled). To enable a policy, select Enabled. To delete
a policy, click Delete. Click Save Settings to save your
changes, or click Cancel Changes to cancel your changes.
To return to the Internet Access Policy screen, click Close.
Access Restrictions > Internet Access
The Internet Access screen allows you to block or allow
specific kinds of Internet usage and traffic, such as Internet
access, designated services, and websites during specific
days and times.
Wireless-G Broadband Router with 2 Phone Ports
19
Advanced Configuration
Chapter 3
6. Decide which days and what times you want this policy
to be enforced. Select the individual days during which
the policy will be in effect, or select Everyday. Then
enter a range of hours and minutes during which the
policy will be in effect, or select 24 Hours.
7. You can block websites with specific URL addresses.
Enter each URL in a separate URL field.
8. You can also block websites using specific keywords.
Enter each keyword in a separate Keyword field.
Summary
Status Policies are disabled by default. To enable a policy,
select the policy number from the drop-down menu, and
select Enabled.
To create a policy, follow steps 1-11. Repeat these steps to
create additional policies, one at a time.
1. Select a number from the Access Policy drop-down
menu.
2. Enter a Policy Name in the field provided.
3. To enable this policy, select Enabled.
4. Click Edit List to select which computers will be
affected by the policy. The List of PCs screen appears.
You can select a PC by MAC address or IP address. You
can also enter a range of IP addresses if you want this
policy to affect a group of computers. After making your
changes, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes. Then
click Close.
9. You can filter access to various services accessed
over the Internet, such as FTP or telnet. (You
can block up to three applications per policy.)
From the Applications list, select the application you
want to block. Then click the >> button to move it to
the Blocked List. To remove an application from the
Blocked List, select it and click the << button.
10. If the application you want to block is not listed
or you want to edit a service’s settings, enter the
application’s name in the Application Name field. Enter
its range in the Port Range fields. Select its protocol
from the Protocol drop-down menu. Then click Add.
To modify a service, select it from the
Application list. Change its name, port range,
and/or protocol setting. Then click Modify.
To delete a service, select it from the Application list.
Then click Delete.
11. Click Save Settings to save the policy’s settings. To
cancel the policy’s settings, click Cancel Changes.
Applications and Gaming > Single Port
Forwarding
The Single Port Forwarding screen allows you to customize
port services for common applications on this screen.
When users send these types of requests to your network via
the Internet, the Router will forward those requests to the
appropriate servers (computers). Before using forwarding,
you should assign static IP addresses to the designated
servers (use the DHCP Reservation feature on the Basic Setup
screen).
List of PCs
5. Select the appropriate option, Deny or Allow,
depending on whether you want to block or allow
Internet access for the computers you listed on the List
of PCs screen.
Wireless-G Broadband Router with 2 Phone Ports
20
Chapter 3
Advanced Configuration
that use Internet access to perform functions such as
videoconferencing or online gaming. Some Internet
applications may not require any forwarding.)
When users send these types of requests to your network via
the Internet, the Router will forward those requests to the
appropriate servers (computers). Before using forwarding,
you should assign static IP addresses to the designated
servers (use the DHCP Reservation feature on the Basic Setup
screen).
If you need to forward all ports to one computer, click the
DMZ tab.
Applications and Gaming > Single Port Forwarding
Single Port Forwarding
Common applications are available for the first five
entries. Select the appropriate application. Then enter the
IP address of the server that should receive these requests.
Select Enabled to activate this entry.
For additional applications, complete the following fields:
Application Name Enter the name you wish to give the
application. Each name can be up to 12 characters.
External Port Enter the external port number used by
the server or Internet application. Check with the Internet
application documentation for more information.
Applications and Gaming > Port Range Forward
Port Range Forward
To forward a port, enter the information on each line for
the criteria required.
Internal Port Enter the internal port number used by
the server or Internet application. Check with the Internet
application documentation for more information.
Application Name In this field, enter the name you
wish to give the application. Each name can be up to 12
characters.
Protocol Select the protocol used for this application,
either TCP, UDP, or Both.
Start~End Port Enter the number or range of port(s)
used by the server or Internet applications. Check
with the Internet application documentation for more
information.
To IP Address For each application, enter the IP address
of the PC that should receive the requests. If you assigned
a static IP address to the PC, then you can click DHCP
Reservation on the Basic Setup screen to look up its static
IP address.
Enabled For each application, select Enabled to enable
port forwarding.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Applications and Gaming > Port Range
Forward
The Port Range Forward screen allows you to set up public
services on your network, such as web servers, ftp servers,
e-mail servers, or other specialized Internet applications.
(Specialized Internet applications are any applications
Wireless-G Broadband Router with 2 Phone Ports
Protocol Select the protocol used for this application,
either TCP, UDP, or Both.
To IP Address For each application, enter the IP address
of the PC running the specific application. If you assigned
a static IP address to the PC, then you can click DHCP
Reservation on the Basic Setup screen to look up its static
IP address.
Enabled Select Enabled to enable port forwarding for
the applications you have defined.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
21
Advanced Configuration
Chapter 3
Applications & Gaming > Port Range
Triggering
The Port Range Triggering screen allows the Router to
watch outgoing data for specific port numbers. The IP
address of the computer that sends the matching data is
remembered by the Router, so that when the requested
data returns through the Router, the data is pulled back
to the proper computer by way of IP address and port
mapping rules.
Applications and Gaming > DMZ
DMZ
Any PC whose port is being forwarded must have its DHCP
client function disabled and should have a new static IP
address assigned to it because its IP address may change
when using the DHCP function.
Enabled/Disabled To disable DMZ hosting, select
Disabled. To expose one PC, select Enabled. Then
configure the following settings:
Applications and Gaming > Port Range Triggering
Port Range Triggering
Application Name Enter the application name of the
trigger.
Triggered Range For each application, enter the starting
and ending port numbers of the triggered port number
range. Check with the Internet application documentation
for the port number(s) needed.
Source IP Address If you want any IP address to be the
source, select Any IP Address. If you want to specify an IP
address or range of IP addresses as the designated source,
select and complete the IP address range fields.
Destination If you want to specify the DMZ host by IP
address, select IP Address and enter the IP address in
the field provided. If you want to specify the DMZ host
by MAC address, select MAC Address and enter the MAC
address in the field provided. To retrieve this information,
click DHCP Client Table.
Forwarded Range For each application, enter the starting
and ending port numbers of the forwarded port number
range. Check with the Internet application documentation
for the port number(s) needed.
Enabled Select Enabled to enable port triggering for the
applications you have defined.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Applications and Gaming > DMZ
The DMZ feature allows one network computer to be
exposed to the Internet for use of a special-purpose
service such as Internet gaming or videoconferencing.
DMZ hosting forwards all the ports at the same time to
one PC. The Port Range Forwarding feature is more secure
because it only opens the ports you want to have opened,
while DMZ hosting opens all the ports of one computer,
exposing the computer to the Internet.
Wireless-G Broadband Router with 2 Phone Ports
DMZ > DHCP Client Table
DHCP Client Table
The DHCP Client Table lists computers and other
devices that have been assigned IP addresses by
the Router. The list can be sorted by Client Name, IP
Address, and MAC Address. To select a DHCP client, click
Select. To retrieve the most up-to-date information,
click Refresh. To exit this screen and return to the DMZ
screen, click Close.
22
Advanced Configuration
Chapter 3
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
select Manual, and enter the appropriate number in the
field provided.
Applications and Gaming > QoS
Category
Quality of Service (QoS) ensures better service to
high-priority types of network traffic, which may
involve demanding, real-time applications, such as
videoconferencing.
There are four categories available. Select one of the
following: Application, Online Games, MAC Address,
or Ethernet Port. Proceed to the instructions for your
selection.
Application
Applications Select the appropriate application. If you
select Add a New Application, follow the Add a New
Application instructions.
Priority Select the appropriate priority: High, Medium,
Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Add a New Application
Applications and Gaming > QoS
QoS (Quality of Service)
Wireless
QoS > Add a New Application
Enter a Name Enter any name to indicate the name of
the entry.
No Acknowledgement If you want to disable the Router’s
Acknowledgement feature, so the Router will not re-send
data if an error occurs, then select Enabled. Otherwise,
keep the default, Disabled.
Port Range Enter the port range that the application will
be using. For example, if you want to allocate bandwidth
for FTP, you can enter 21-21. If you need services for an
application that uses from 1000 to 1250, you enter 10001250 as your settings. You can have up to three ranges
to define for this bandwidth allocation. Port numbers
can range from 1 to 65535. Check your application’s
documentation for details on the service ports used.
Internet Access Priority
Select the protocol TCP, UDP, or Both.
WMM Support If you have other devices that support
Wi‑Fi Multimedia (WMM) on your network, select Enabled.
Otherwise, keep the default, Disabled.
In this section, you can set the bandwidth priority for a
variety of applications and devices. There are four levels
priority: High, Medium, Normal, or Low. When you set
priority, do not set all applications to High, because this will
defeat the purpose of allocating the available bandwidth.
If you want to select below normal bandwidth, select Low.
Depending on the application, a few attempts may be
needed to set the appropriate bandwidth priority.
Priority Select the appropriate priority: High, Medium
(Recommend), Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Online Games
Enabled/Disabled To use the QoS policies you have set,
keep the default, Enabled. Otherwise, select Disabled.
Upstream Bandwidth To allow the Router to control the
maximum bandwidth for upstream data transmissions,
keep the default, Auto. To manually set the maximum,
Wireless-G Broadband Router with 2 Phone Ports
QoS > Online Games
23
Advanced Configuration
Chapter 3
Game Select the appropriate game. If you select Add a
New Game, follow the Add a New Game instructions.
Ethernet Port
Priority Select the appropriate priority: High, Medium
(Recommend), Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Add a New Game
QoS > Ethernet Port
Ethernet Select the appropriate Ethernet port.
Priority Select the appropriate priority: High, Medium
(Recommend), Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Summary
QoS > Add a New Game
This lists the QoS entries you have created for your
applications and devices.
Enter a Name Enter any name to indicate the name of
the entry.
Priority This column displays the bandwidth priority of
High, Medium, Normal, or Low.
Port Range Enter the port range that the application will
be using. For example, if you want to allocate bandwidth
for FTP, you can enter 21-21. If you need services for an
application that uses from 1000 to 1250, you enter 10001250 as your settings. You can have up to three ranges
to define for this bandwidth allocation. Port numbers
can range from 1 to 65535. Check your application’s
documentation for details on the service ports used.
Name This column displays the application, device, or
port name.
Select the protocol TCP, UDP, or Both.
Edit Click this button to make changes.
Priority Select the appropriate priority: High, Medium
(Recommend), Normal, or Low.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Administration > Management
MAC Address
The Administration > Management screen allows the
network’s administrator to manage specific Router
functions for access and security.
Information This column displays the port range or
MAC address entered for your entry. If a pre-configured
application or game was selected, there will be no valid
entry shown in this section.
Remove Click this button to remove an entry.
QoS > MAC Address
Enter a Name Enter a name for your device.
MAC Address Enter the MAC address of your device.
Priority Select the appropriate priority: High, Medium
(Recommend), Normal, or Low.
Click Add to save your changes. Your new entry will appear
in the Summary list.
Wireless-G Broadband Router with 2 Phone Ports
24
Advanced Configuration
Chapter 3
Web Utility Access HTTP (HyperText Transport Protocol)
is the communications protocol used to connect to servers
on the World Wide Web. HTTPS uses SSL (Secured Socket
Layer) to encrypt data transmitted for higher security.
Select HTTP or HTTPS. HTTP is the default.
Remote Upgrade If you want to be able to upgrade the
Router remotely, from outside the local network, select
Enabled. (You must have the Remote Management
feature enabled as well.) Otherwise, keep the default,
Disabled.
Allowed Remote IP Address If you want to be able to
access the Router from any external IP address, select Any
IP Address. If you want to specify an external IP address or
range of IP addresses, then select the second option and
complete the fields provided.
Remote Management Port Enter the port number that
will be open to outside access.
NOTE: When you are in a remote location
and wish to manage the Router, enter
http://<Internet_IP_address>:port
or
https://<Internet_IP_address>:port,
depending on whether you use HTTP or HTTPS.
Enter the Router’s specific Internet IP address in
place of <Internet_IP_address>, and enter the
Remote Management Port number in place of
the word port.
Administration > Management
Management
Router Access
To ensure the Router’s security, you will be asked for your
password when you access the Router’s web-based utility.
The default is admin.
Router Password Enter a new password for the Router.
Re-enter to confirm Enter the password again to
confirm.
Web Access
Web Utility Access HTTP (HyperText Transport Protocol)
is the communications protocol used to connect to servers
on the World Wide Web. HTTPS uses SSL (Secured Socket
Layer) to encrypt data transmitted for higher security.
Select HTTP or HTTPS. HTTP is the default.
Web Utility Access via Wireless If you are using the
Router in a public domain where you are giving wireless
access to your guests, you can disable wireless access to
the Router’s web-based utility. You will only be able to
access the utility via a wired connection if you disable
the setting. Keep the default, Enabled, to allow wireless
access to the utility, or select Disabled to block wireless
access to the utility.
Remote Access
Remote Management To permit remote access of the
Router, from outside the local network, select Enabled.
Otherwise, keep the default, Disabled.
Wireless-G Broadband Router with 2 Phone Ports
UPnP
Universal Plug and Play (UPnP) allows Windows XP and Vista
to automatically configure the Router for various Internet
applications, such as gaming and videoconferencing.
UPnP If you want to use UPnP, keep the default, Enabled.
Otherwise, select Disabled.
Allow Users to Configure Keep the default, Enabled,
if you want to be able to make manual changes to the
Router while using the UPnP feature. Otherwise, select
Disabled.
Keep UPnP Configurations After System Reboot If
you enable the Allow Users to Configure option, then this
option will be available. Select Enabled, if you want to
keep UPnP configuration settings after the Router reboots.
Otherwise, keep the default, Disabled.
Allow Users to Disable Internet Access Select Enabled,
if you want to be able to prohibit any and all Internet
connections. Otherwise, keep the default, Disabled.
Multimedia Streaming
RTSP Support If you are experience issues with videoon-demand applications, select Enabled to improve
multimedia transmissions. Using this option, the Router
will establish channels with the Real Time Streaming
25
Advanced Configuration
Chapter 3
Protocol) RTSP server, which is located at the ISP. Otherwise,
keep the default, Disabled.
IGMP
Internet Group Multicast Protocol (IGMP) is used to
establish membership in a multicast group and is
commonly used for multicast streaming applications. For
example, you may have Internet Protocol Television (IPTV)
with multiple setup boxes on the same local network.
These setup boxes have different video streams running
simultaneously, so you should use the IGMP feature of the
Router.
Support IGMP Version Select the version you want to
support, IGMP v1, IGMP v2, or IGMP v3. If you are not
sure which version to select, keep the default, IGMP v2.
IGMP Proxy Keep the default, Enabled, if you want
to allow multicast traffic through the Router for your
multimedia application devices. Otherwise, select
Disabled.
Immediate Leave Select Enabled, if you use IPTV
applications and want to allow immediate channel
swapping or flipping without lag or delays. Otherwise,
keep the default, Disabled.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Log
The Router can keep logs of all traffic for your Internet
connection.
Log > View Log
Log
•
Type Select Incoming Log, Outgoing Log, Security
Log, or DHCP Client Log.
•
<Type> Log The Incoming Log will display a temporary
log of the source IP addresses and destination
port numbers for the incoming Internet traffic. The
Outgoing Log will display a temporary log of the
local IP addresses, destination URLs/IP addresses, and
service/port numbers for the outgoing Internet traffic.
The Security log will display the login information for
the web-based utility. The DHCP Client Log will display
the LAN DHCP server status information.
Click Refresh to update the log. Click Clear to clear all
the information that is displayed.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Diagnostics
The diagnostic tests (Ping and Traceroute) allow you to
check the connections of your network devices, including
connection to the Internet.
Administration > Log
Log
Log To disable the Log function, keep the default,
Disabled. To monitor traffic between the network and the
Internet, select Enabled. With logging enabled, you can
choose to view temporary logs.
View Log To view the logs, click View Log.
Wireless-G Broadband Router with 2 Phone Ports
Administration > Diagnostics
26
Advanced Configuration
Chapter 3
Diagnostics
Ping Test
The Ping test checks the status of a connection.
IP or URL Address Enter the address of the PC whose
connection you wish to test.
Packet Size Enter the packet size you want to use. The
default is 32 bytes.
Times to Ping Enter many times you wish to test it.
Start to Ping To run the test, click this button. The Ping
Test screen will show if the test was successful. Click Close
to return to the Diagnostics screen.
Diagnostics > Traceroute
Administration > Factory Defaults
The Administration > Factory Defaults screen allows
you to restore the Router’s configuration to its Router
and/or voice factory default settings.
Diagnostics > Ping
Traceroute Test
The Traceroute test tests the performance of a
connection.
IP or URL Address Enter the address of the PC whose
connection you wish to test.
Start to Traceroute To run the test, click this button. The
Traceroute Test screen will show if the test was successful.
Click Close to return to the Diagnostics screen.
Administration > Factory Defaults
NOTE: Restoring factory defaults deletes custom
settings. Note your custom settings before
restoring the factory defaults.
Factory Defaults
Restore Router Factory Defaults To reset the Router
settings to the default values, select Yes. Then click Save
Settings. Any custom Router settings you have saved will
be lost when the default settings are restored.
Restore Voice Factory Defaults To reset the voice
settings to the default values, select Yes. Then click Save
Settings. Any custom Voice settings you have saved will
be lost when the default settings are restored.
NOTE: Restoring the voice defaults may require
your login (the default user name and password
are admin). If the defaults do not work, contact
your ITSP for more information.
Wireless-G Broadband Router with 2 Phone Ports
27
Advanced Configuration
Chapter 3
On the Firmware Upgrade screen, click Save Settings to
apply your changes, or click Cancel Changes to cancel
your changes.
Administration > Firmware Upgrade
The Firmware Upgrade screen allows you to upgrade the
Router’s firmware. Do not upgrade the firmware unless
you are experiencing problems with the Router or the new
firmware has a feature you want to use.
If you want to upgrade the Router’s firmware, then you may
need a user name and password available only from your
ISP or ITSP. Contact your ISP or ITSP for more information.
Administration > Firmware Upgrade
Username & Password
Please select a file to upgrade Click Browse and select
the extracted firmware upgrade file.
If you see the Username & Password screen, enter the User
Name and Password provided by your ISP or ITSP. Then
click Save Settings.
Start to Upgrade After you have selected the
appropriate file, click this button, and follow the on-screen
instructions.
Administration > Config Management
The Config Management screen allows you to back up or
restore the Router’s settings using a configuration file.
Administration > Username & Password
NOTE: The Router may lose the settings you
have customized. Before you upgrade its
firmware, use the Config Management screen
to back up the Router’s settings. Refer to the
Administration > Config Management section for
more information.
Administration > Config Management
Backup Configuration
Firmware Upgrade
Backup To save the Router’s settings in a configuration file,
click this button and follow the on-screen instructions.
Before upgrading the firmware, download the Router’s
firmware upgrade file from the Linksys website,
www.linksys.com. Then extract the file.
Restore Configuration
To use this option, you must have previously backed up its
configuration settings.
Please select a file to restore Click the Browse button
and select the Router’s configuration file.
Restore To restore the Router’s configuration settings,
click this button and follow the on-screen instructions.
Status > Router
The Router screen displays information about the Router.
Wireless-G Broadband Router with 2 Phone Ports
28
Advanced Configuration
Chapter 3
Status > Local Network
Local Network
Local MAC Address The MAC address of the Router’s
local, wired interface is displayed.
Status > Router
Router Information
Firmware Version The version number of the Router’s
current firmware is displayed.
Current Time The time set on the Router is displayed.
Internet MAC Address The Router’s MAC address, as
seen by your ISP, is displayed.
Router Name The name of the Router is displayed.
Host Name If required by your ISP, this was entered on
the Basic Setup screen.
Domain Name If required by your ISP, this was entered
on the Basic Setup screen.
Internet Connection
Router IP Address The Router’s IP address, as it appears
on your local network, is displayed.
Subnet Mask The Subnet Mask of the Router is
displayed.
DHCP Server
DHCP Server The status of the Router’s DHCP server
function is displayed.
Start IP Address For the range of IP addresses used by
devices on your local network, the starting IP address is
displayed.
End IP Address For the range of IP addresses used by
devices on your local network, the ending IP address is
displayed.
DHCP Clients Table Click this button to view a list of
computers that are using the Router as a DHCP server.
This section shows the current network information.
It varies depending on the Internet connection type
selected on the Basic Setup screen.
Click Refresh to update the on-screen information.
Status > Local Network
The Local Network screen displays information about the
local, wired network.
DHCP Clients Table
DHCP Client Table
The DHCP Client Table lists computers and other
devices that have been assigned IP addresses by
the Router. The list can be sorted by Client Name, IP
Address, Interface, MAC Address, and Expires Time
(how much time is left for the current IP address). To
Wireless-G Broadband Router with 2 Phone Ports
29
Advanced Configuration
Chapter 3
remove a DHCP client, click Delete. To retrieve the
most up-to-date information, click Refresh. To exit
this screen and return to the Local Network screen,
click Close.
Status > Wireless Network
The Wireless Network screen displays information about
your wireless network(s).
enter the user name and password provided by your ITSP.
Contact your ITSP for more information. (The factory
default Admin Login name and password are admin.)
NOTE: In most cases, you do not need to use
the administrative screens. Contact your ITSP for
more information.
Voice > Info
The Info screen displays Voice over Internet Protocol (VoIP)
information about the Router.
Status > Wireless Network
Wireless Network
Dynamic Channel Selection The setting is displayed.
Channel The channel of the wireless network(s) is
displayed.
Mode The wireless mode is displayed.
Wireless Network 1-2
Status information for each wireless network is displayed.
Wireless MAC Address The wireless MAC address of the
Router’s local, wireless interface is displayed.
Network Name (SSID) The network name, which is also
called the SSID, is displayed.
Security The wireless security method is displayed.
SSID Broadcast The status of the SSID Broadcast feature
is displayed.
Voice > Info
Access to the Voice Screens
Product Information
There are two level of access, user and Admin Login. When
you click the Voice tab, the Info screen is automatically
displayed. If you set a User Password on the System screen,
then you will be asked to enter it before the Info screen is
displayed.
Product Name The model number of the Router is
displayed.
The Admin Login allows access to more advanced settings.
To access administrative screens, click Admin Login, and
Wireless-G Broadband Router with 2 Phone Ports
Serial Number The serial number of the Router is
displayed.
Software Version The version number of the Router
software is displayed.
30
Chapter 3
Hardware Version The version number of the Router
hardware is displayed.
MAC Address The MAC address of the Router is
displayed.
Client Certificate The status of the client certificate,
which indicates that the Router has been authorized by
your ITSP, is displayed.
System Status
Current Time The current date and time of the Router are
displayed.
Elapsed Time The amount of time elapsed since the last
reboot of the Router is displayed.
RTP Packets Sent The number of RTP packets sent by the
Router is displayed.
RTP Bytes Sent The number of RTP bytes sent by the
Router is displayed.
Advanced Configuration
Last Called Number The last number called is displayed.
Last Caller Number The number of the last caller is
displayed.
Mapped SIP Port The port number of the NAT mapped
SIP port is displayed.
Calls 1 and 2 have the same status information available.
Call 1/2 State The status of the call is displayed.
Call 1/2 Tone The type of tone used by the call is
displayed.
Call 1/2 Encoder The codec used for encoding is
displayed.
Call 1/2 Decoder The codec used for decoding is
displayed.
Call 1/2 FAX The status of the fax pass-through mode is
displayed.
Call 1/2 Type The direction of the call is displayed.
RTP Packets Recv The number of RTP packets received
by the Router is displayed.
Call 1/2 Remote Hold This indicates whether the far end
has placed the call on hold.
RTP Bytes Recv The number of RTP bytes received by the
Router is displayed.
Call 1/2 Callback This indicates whether the call was
triggered by a call back request.
SIP Messages Sent The number of SIP messages sent by
the Router is displayed.
Call 1/2 Peer Name The name of the internal phone is
displayed.
SIP Bytes Sent The number of SIP bytes sent by the
Router is displayed.
Call 1/2 Peer Phone The phone number of the internal
phone is displayed.
SIP Messages Recv The number of SIP messages received
by the Router is displayed.
Call 1/2 Duration The duration of the call is displayed.
SIP Bytes Recv The number of SIP bytes received by the
Router is displayed.
External IP The external IP address used for NAT mapping
is displayed.
Line 1/2 Status
Lines 1 and 2 have the same status information available.
Hook State The status of the Internet phone line’s
readiness is displayed. “On” indicates that it is ready for
use, while “Off” indicates that it is in use.
Registration State The status of the line’s registration
with the ITSP is displayed.
Last Registration At The last date and time the line was
registered are displayed.
Next Registration In The number of seconds until the
next registration is displayed.
Message Waiting This indicates whether you have new
voicemail waiting.
Call Back Active This indicates whether a call back
request is in progress.
Wireless-G Broadband Router with 2 Phone Ports
Call 1/2 Packets Sent The number of packets sent is
displayed.
Call 1/2 Packets Recv The number of packets received
is displayed.
Call 1/2 Bytes Sent The number of bytes sent is
displayed.
Call 1/2 Bytes Recv The number of bytes received is
displayed.
Call 1/2 Decode Latency The number of milliseconds for
decoder latency is displayed.
Call 1/2 Jitter The number of milliseconds for receiver
jitter is displayed.
Call 1/2 Round Trip Delay The number of milliseconds
for delay is displayed.
Call 1/2 Packets Lost The number of packets lost is
displayed.
Call 1/2 Packet Error The number of invalid packets
received is displayed.
Call 1/2 Mapped RTP Port The number of the NAT
mapped RTP port is displayed.
31
Advanced Configuration
Chapter 3
Call 1/2 Media Loopback The Media Loopback feature
allows the ITSP to test the quality of the connection to the
Router. The status of the feature is displayed.
Voice > System
The System screen displays the User Password setting.
Voice > System
System Configuration
User Password Enter the password for user access to the
Voice screens. (By default, there is no password.)
Miscellaneous Settings
No settings are displayed.
Click Save Settings to apply your change, or click Cancel
Changes to cancel your change.
Voice > User 1/2
The User 1 and 2 screens display similar settings. The User 1
screen displays settings for users of phone line 1, and the
User 2 screen displays settings for users of phone line 2.
Voice > User 1
Call Forward Settings
Enter the call forwarding numbers you want to use.
Cfwd All Dest Enter the number for the Call Forward All
Service feature (when you want to forward all calls).
Cfwd Busy Dest Enter the number for the Call Forward
Busy feature (when the line is busy).
Cfwd No Ans Dest Enter the number for the Call Forward
No Answer feature (when the line is not answered).
Cfwd No Ans Delay Enter the number of seconds to wait
before the Call Forward No Answer feature is triggered.
The default is 20.
Selective Call Forward Settings
Enter the caller numbers that will be forwarded to specific
phone numbers.
Cfwd Sel1-8 Caller Enter the caller number pattern to
trigger the Call Forward Selective (1-8) feature.
Cfwd Sel1-8 Dest Enter the forward number for the Call
Forward Selective (1-8) feature.
Cfwd Last Caller Enter the caller number that is actively
forwarded to the Cfwd Last Dest number when the Call
Forward Last activation code is used.
Cfwd Last Dest Enter the forward number for the Cfwd
Last Caller feature.
Wireless-G Broadband Router with 2 Phone Ports
32
Chapter 3
Block Last Caller Enter the ID of the caller blocked via
the Block Last Caller service.
Accept Last Caller Enter the ID of the caller accepted via
the Accept Last Caller service.
Advanced Configuration
VMWI Ring Splash Len Enter the duration of the ring
splash when new messages arrive before the VoiceMail
Waiting Indication (VMWI) signal is applied. The range is 0
to 10.0 seconds. The default is 0.
Speed Dial Settings
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Speed Dial 2-9 Enter the phone number for each Speed
Dial setting.
Voice > Admin Login
Supplementary Service Settings
CW Setting Select whether you want to use the Call
Waiting feature for all calls, yes or no. The default is yes.
Block CID Setting Select whether you want to block
Caller ID for all calls, yes or no. The default is no.
Block ANC Setting Select whether you want to block
anonymous calls, yes or no. The default is no.
The Admin Login allows access to more advanced settings.
To access administrative screens, click Admin Login, and
enter the user name and password provided by your ITSP.
Contact your ITSP for more information. (The factory
default Admin Login name and password are admin.)
NOTE: In most cases, you do not need to use
the administrative screens. Contact your ITSP for
more information.
DND Setting Select whether you want to use the Do Not
Disturb (DND) feature, yes or no. The default is no.
CID Setting Select whether you want to enable Caller ID
generation, yes or no. The default is yes.
CWCID Setting Select whether you want to enable Caller
ID for Call Waiting, yes or no. The default is yes.
Dist Ring Setting Select whether you want to use the
Distinctive Ring feature, yes or no. The default is yes.
Message Waiting Select whether you want to use the
Message Waiting feature, yes or no. The default is no.
Distinctive Ring Settings
Ring1-8 Caller Enter the caller number pattern to play
Distinctive Ring/Call Waiting Tone (1-8).
Ring Settings
Default Ring Select the default ringing pattern for all
callers. The default is 1.
Default CWT Select the default CWT pattern for all callers.
The default is 1.
Hold Reminder Ring Select the ring pattern that will
remind you of a call on hold when the phone is on-hook.
The default is 8.
Call Back Ring Select the ring pattern for call back
notification. The default is 7.
Cfwd Ring Splash Len Enter the duration of the ring
splash when a call is forwarded. The range is 0 to 10.0
seconds. The default is 0.
Cblk Ring Splash Len Enter the duration of the ring
splash when a call is blocked. The range is 0 to 10.0
seconds. The default is 0.
Wireless-G Broadband Router with 2 Phone Ports
33
Interactive Voice Response Menu
Chapter 4
Chapter 4:
Interactive Voice
Response Menu
Overview
This chapter explains how to use the Interactive Voice
Response (IVR) Menu to configure the Router’s network
settings. Use your telephone’s keypad to enter your
commands and select choices, and the Router will use
voice responses.
Action
Command Choices Description
****
Use this command
to enter the IVR
Menu. Ignore
Special Information
Tones (SITs) or other
tones until you
hear, “Configuration
menu. Please enter
the option followed
by the # (pound)
key, or hang up to
exit.”
Check DHCP 100
The IVR announces
whether DHCP is
enabled or disabled.
Enter IVR
Menu
To access the IVR Menu:
1. Use a telephone connected to the Phone 1 or 2 port of
the Router. (You can only access the IVR Menu through
an analog telephone, not any of the Internet phones.)
2. Press **** (in other words, press the star key four
times).
3. Wait until you hear the Router’s response,
“Configuration menu. Please enter the option followed
by the # (pound) key, or hang up to exit”.
Menu Commands
Refer to the following table that lists actions, commands,
menu choices, and descriptions. After you select an
option, press the # (pound) key. To exit the menu, hang
up the telephone.
If the menu is inactive for more than one minute, the
Router will time out. To re-enter the menu, press ****.
Check IP
Address
110
The IVR announces
the current IP
address of the
Router.
Check
Subnet
Mask
120
The IVR announces
the current subnet
mask of the Router.
Check Static
Gateway IP
Address
130
The IVR announces
the current gateway
IP address of the
Router.
Check MAC
Address
140
The IVR announces
the MAC address
of the Router in
hexadecimal string
format.
Check
Firmware
Version
150
The IVR announces
the version number
of the firmware
running on the
Router.
Factory
Reset of the
Router
73738
Warning:
All custom
settings
will be lost,
including
the network
and service
provider
data.
Wireless-G Broadband Router with 2 Phone Ports
Confirm - After the
Press 1.
Router requests
Cancel - confirmation, press
1 to confirm.
Press *
(star).
After you hear,
“Option successful”,
hang up the phone.
The Router will
reboot, and all
settings will be reset
to their defaults.
34
Troubleshooting
Appendix A
Appendix A:
Troubleshooting
Your computer cannot connect to the Internet.
When you are on an Internet phone call, words are
dropped intermittently.
Follow these instructions until your problem is solved:
•
If you are using the Router’s wireless function and
a cordless phone, they may be using the same
frequency and may interfere with each other. Move
the cordless phone farther away from the Router.
•
There may be heavy network activity, particularly if you
are running a server or using a file sharing program.
Try to limit network or Internet activity during
Internet phone calls. For example, if you are running
a file sharing program, files may be uploaded in the
background even though you are not downloading
any files, so make sure you exit the program before
making Internet phone calls.
•
There may not be enough bandwidth available
for your Internet phone call. You may want to test
your bandwidth using one of the bandwidth tests
available online. If necessary, access your Internet
phone service account and reduce the bandwidth
requirements for your service. For more information,
refer to the website of your ITSP.
Follow these instructions until your computer can connect
to the Internet:
•
Make sure that the Router is powered on. The Power
LED should be green and not flashing.
•
If the Power LED is flashing, then power off all of your
network devices, including the modem, Router, and
computers. Wait 30 seconds. Then power on each
device in the following order:
•
1.
Cable or DSL modem
2.
Router
3.
Computer
Check the cable connections. The computer should
be connected to one of the ports numbered 1-4 on
the Router, and the modem must be connected to the
Internet port on the Router.
You do not hear a dial tone, and the Phone 1 or 2 LED is
not lit.
Follow these instructions until your problem is solved:
•
Make sure the telephone is plugged into the
appropriate port, Phone 1 or 2.
•
Disconnect and re-connect the RJ-11 telephone cable
between the Router and telephone.
•
Make sure your telephone is set to its tone setting
(not pulse).
•
Make sure your network has an active Internet
connection. Try to access the Internet, and check to
see if the Router’s Internet LED is lit. If you do not
have a connection, then power off all of your network
devices, including the modem, Router, and computers.
Wait 30 seconds. Then power on each device in the
following order:
•
1.
Cable or DSL modem
2.
Router
3.
Computers and other devices
The modem does not have an Ethernet port.
The modem is a dial-up modem for traditional dial-up
service. To use the Router, you need a cable/DSL modem
and high-speed Internet connection.
You cannot use the DSL service to connect manually to
the Internet.
After you have installed the Router, it will automatically
connect to your Internet Service Provider (ISP) or Internet
Telephony Service Provider (ITSP), so you no longer need
to connect manually.
The DSL telephone line does not fit into the Router’s
Internet port.
The Router does not replace your modem. You still need
your DSL modem in order to use the Router. Connect
the telephone line to the DSL modem, insert the setup
CD into your computer, and then follow the on‑screen
instructions.
Verify your account information and confirm that the
phone line is registered with your Internet Telephony
Service Provider (ITSP).
Wireless-G Broadband Router with 2 Phone Ports
35
Appendix A
Troubleshooting
When you double-click the web browser, you are
prompted for a username and password. If you want to
get rid of the prompt, follow these instructions.
Launch the web browser and perform the following steps
(these steps are specific to Internet Explorer but are similar
for other browsers):
1.
Select Tools > Internet Options.
2.
Click the Connections tab.
3.
Select Never dial a connection.
4.
Click OK.
The Router does not have a coaxial port for the cable
connection.
The Router does not replace your modem. You still need
your cable modem in order to use the Router. Connect your
cable connection to the cable modem, insert the setup
CD into your computer, and then follow the on‑screen
instructions.
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same
on both the computer and the Router. If you have enabled
wireless security, then make sure the same security
method and key are used by both the computer and the
Router.
You need to modify the settings on the Router.
To access the web-based utility, follow these instructions:
1. Launch the web browser on your computer, and enter
the Router’s default IP address, 192.168.15.1, in the
Address field. Then press Enter.
NOTE: If you place the Router behind a primary
router with the IP address of 192.168.15.1, then
the Router will automatically assume a new
default IP address, 192.168.16.1.
2. A login screen appears. The first time you open the
web-based utility, use the default user name and
password, admin. (You can set a new password from
the Administration tab’s Management screen.) Then
click OK.
3. Click the appropriate tab to change the settings.
WEB: If your questions are not addressed here,
refer to the Linksys website, www.linksys.com.
Wireless-G Broadband Router with 2 Phone Ports
36
Specifications
Appendix B
Appendix B:
Specifications
IP Multicast / IGMP v1, v2, v3/
IGMP Proxy
Voice Features
Voice Algorithms
G.711 (a-law and µ-law)
Model
WRP400
G.726 (16/24/32/40 kbps)
* Note: Many specifications are programmable within a
defined range or list of options. Please see the SPA ATA
Administration Guide for details. The target configuration
profile is uploaded to the WRP400 at the time of
provisioning.
G.729 AB
G.723.1 (6.3 kbps, 5.3 kbps)
Call Forwarding:
No Answer/Busy/Unconditional
Data Networking MAC Address (IEEE 802.3)
Support for Two Simultaneous Calls
IPv4 - Internet Protocol v4 (RFC 791)
Upgradeable to v6 (RFC 1883)
SIP TLS (Transport Layer Security)
Call Transfer
ARP - Address Resolution Protocol
Call Waiting/Hold/Retrieve
DNS - A Record (RFC 1706),
SRV Record (RFC 2782)
Three-way Conferencing
DHCP Client - Dynamic Host
Configuration Protocol (RFC 2131)
Call ID Number & Name (Primary
Line & On Call Waiting)
DHCP Server - Dynamic Host
Configuration Protocol (RFC 2131)
Call-ID Block (Prevent Send out the
Caller ID)
Anonymous Call Blocking
PPPoE Client - Point to Point
Protocol over Ethernet (RFC 2516)
Distinctive Ringing
ICMP - Internet Control Message
Protocol (RFC792)
Do not Disturb Setting
Repeat Dialing on Busy
TCP - Transmission Control Protocol
(RFC793)
Call Return
Emergency Call Support
UDP - User Datagram Protocol
(RFC768)
Dial Plan
Speed Dial
RTP - Real Time Protocol (RFC 1889)
(RFC 1890)
Auto-Attendant
RTCP - Real Time Control Protocol
(RFC 1889)
Multi-Room Meet-Me Conference
In-Band/ SIP-INFO DTMF Translation
TFTP
RTSP
HTTP
Provisioning,
Administration,
& Maintenance
Web Browser Administration &
Configuration via Integral Web Server
NAT (RFC 1631)
Reverse NAT
Telephone Key Pad Configuration
with Interactive Voice Prompts
SDP
SNTP - Simple Network Time
Protocol (RFC 2030)
Automated Provisioning & Upgrade
via HTTP, TFTP, HTTPS
Type of Service - TOS
(RFC 791/1349)
Asynchronous Notification of
Upgrade Availability via NOTIFY
Non-Intrusive, In-Service Upgrades
QoS - Packet Prioritization by Type
Report Generation & Event Logging
Router or Bridge Mode of
Operation
Stats in BYE Message
Syslog & Debug Server Records
MAC Address Cloning
Port Forwarding
Per Line and Purpose Configurable
Syslog and Debug Options
Wireless-G Broadband Router with 2 Phone Ports
37
Specifications
Appendix B
Physical Interfaces 4 100Base-T RJ-45 Ethernet Port
(IEEE 802.3)
2 RJ-11 FXS Phone Ports - For
Analog Circuit Telephone Device
USB 2.0 (reserved for future use via
firmware upgrade)
Buttons
Reset, WPS
Subscriber Line
Interface Circuit
(SLIC)
Ring Voltage: 40-90 Vpk
Ring Frequency: 20 to 25Hz
Ring Waveform: Trapezoidal with
1.2 to 1.6 Crest Factor
Maximum Ringer Load: 3 REN
On-Hook/Off-Hook Characteristics:
On-Hook Voltage (Tip/Ring):
- 46 to -56V
Off-Hook Current:
18 to 25mA
Terminating Impedance:
600 ohm Resistive
270 ohm + 750ohm//150nF
Complex Impedance
Frequency Response: 300 – 3400Hz
Regulatory
Compliance
FCC (Part 15 Class B), CE, ICES-003,
RoHS
Number of
Antennas
Connector type
Indicator Lights/
LEDs
Power, Ethernet, Wireless, Phone 1,
Phone 2, Internet, WPS
Documentation
Quick Installation and User Guide are
Downloaded from www.linksys.com
Linksys SPA ATA Administration
Guide - Service Providers Only
Linksys Provisioning Guide - Service
Providers Only
Security Features Password-Protected Configuration
for Web Access
Denial of Service (DoS) Prevention
URL Filtering, and Keyword, Java,
ActiveX, Proxy, Cookie Blocking
VPN Passthrough for IPSec, PPTP,
and L2TP Protocols
64, 128 bits WEP with Passphrase
WEP Key Generation
SSID Broadcast Disable
Access Restriction by MAC and IP
Addresses
Wi-Fi Protected Setup (WPS),
Wi-Fi Protected Access™ (WPA),
Wi-Fi Protected Access™ 2 (WPA2)
Security Key Bits
64, 128
Environmental
Dimensions
5.51" x 5.51" x 1.06"
(140 x 140 x 27 mm)
1
Weight
10.05 oz (285 g)
Fixed
Power
External, Switching, 5VDC, 2A
FCC, CE, CB, IC, UL,
Wi-Fi (802.11b + WPA2,
802.11g + WPA2, WMM)
RF Pwr (EIRP)
in dBm
(Average, not Including Antenna)
Certification
802.11g: Typ. 18 dBm @ Normal
Temp Range (with PA)
Operating Temp. 0 to 40°C (32 to 104°F)
Storage Temp.
-20 to 70°C (-4 to 158°F)
802.11b: Typ: 20 dBm @ Normal
Temp Range (with PA)
Antenna Gain
in dBi
Operating
Humidity
10 to 85%, Relative Humidity,
Noncondensing
2 dBi
Storage Humidity 5 to 90% Noncondensing
UPnP able/cert
Yes
Power Supply
Switching Type (100-240V) Automatic
DC Input Voltage: +5 VDC at
2.0 A Max.
Power Consumption: 7.9 watts
(Average)
Power Adapter: 100-240V - 50-60Hz
(26-34VA) AC Input, 1.8 m Cord
Detachable (y/n) No
Wireless-G Broadband Router with 2 Phone Ports
38
Appendix C
Appendix C:
Warranty Information
Contact your service provider if the warranty support
issues are to be handled by them as per your service
agreements.
Limited Warranty
Linksys warrants to You that, for a period of one year
(the “Warranty Period”), your Linksys Product will be
substantially free of defects in materials and workmanship
under normal use. Your exclusive remedy and Linksys’
entire liability under this warranty will be for Linksys at
its option to repair or replace the Product or refund Your
purchase price less any rebates. This limited warranty
extends only to the original purchaser.
Warranty Information
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
OUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty or
remedy provided under this Agreement fails of its essential
purpose. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to You.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
If the Product proves defective during the Warranty
Period call Linksys Technical Support in order to obtain
a Return Authorization Number, if applicable. BE SURE
TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN
CALLING. If You are requested to return the Product, mark
the Return Authorization Number clearly on the outside
of the package and include a copy of your original proof
of purchase. RETURN REQUESTS CANNOT BE PROCESSED
WITHOUT PROOF OF PURCHASE. You are responsible
for shipping defective Products to Linksys. Linksys pays
for UPS Ground shipping from Linksys back to You only.
Customers located outside of the United States of America
and Canada are responsible for all shipping and handling
charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF NONINFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do
not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to You. This
warranty gives You specific legal rights, and You may also
have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been
altered, except by Linksys, (b) has not been installed,
operated, repaired, or maintained in accordance with
instructions supplied by Linksys, or (c) has been subjected
to abnormal physical or electrical stress, misuse,
negligence, or accident. In addition, due to the continual
development of new techniques for intruding upon and
attacking networks, Linksys does not warrant that the
Product will be free of vulnerability to intrusion or attack.
Wireless-G Broadband Router with 2 Phone Ports
39
Regulatory Information
Appendix D
Appendix D:
Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
•
Do not use this product near water, for example, in a
wet basement or near a swimming pool.
•
Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
WARNING: This equipment will be inoperable
when main power fails.
WARNING: Many Internet phone service
providers do not support calls to emergency
service numbers (000 in Australia or 111 in New
Zealand). An alternative phone should be used
to make emergency calls.
WARNING: To ensure compliance with
explosure limits to radiofrequency fields, the
antenna of the WRP400 should be no closer
than 20 cm from the body during use.
Industry Canada Statement
This Class B digital apparatus complies with Canadian
ICES-003 and RSS210.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation
of the device. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the EIRP is not more than required for successful
communication.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator and your
body.
Industry Canada Radiation Exposure Statement
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. IEEE
802.11b or 802.11g operation of this product in the USA is
firmware-limited to channels 1 through 11.
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
Safety Notices and Information
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
•
Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
Wireless-G Broadband Router with 2 Phone Ports
40
Appendix D
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme aux
normes NMB-003 et RSS210 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
1. il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif. Afin de réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure
au niveau requis pour obtenir une communication
satisfaisante.
Avis d’Industrie Canada concernant l’exposition
aux radiofréquences :
Regulatory Information
Avis de non-responsabilité concernant les
appareils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
Telepermit Statement
The cabling between the phone port and the phone shall
not exceed 100 metres.
Ce matériel est conforme aux limites établies par IC
en matière d’exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 20 cm entre l’antenne
et le corps de l’utilisateur.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Wireless-G Broadband Router with 2 Phone Ports
41
Regulatory Information
Appendix D
Declaration of Conformity with Regard to
EU Directive 1999/5/EC (R&TTE Directive)
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen
en andere van toepassing zijnde bepalingen
van de Richtlijn 1999/5/EC.
Compliance Information for 2,4-GHz and 5-GHz Wireless
Products Relevant to the EU and Other Countries Following
the EU Directive 1999/5/EC (R&TTE Directive)
Malti
[Maltese]:
Dan l-apparat huwa konformi mal-ħtiġiet
essenzjali u l-provedimenti l-oħra rilevanti
tad-Direttiva 1999/5/EC.
Magyar
[Hungarian]:
Ez a készülék teljesíti az alapvető
követelményeket
és
más
1999/5/EK
irányelvben
meghatározott
vonatkozó
rendelkezéseket.
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de
grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Urządzenie jest zgodne z ogólnymi
wymaganiami oraz szczególnymi warunkami
określonymi Dyrektywą UE: 1999/5/EC.
Português
[Portuguese]:
Este equipamento está em conformidade com
os requisitos essenciais e outras provisões
relevantes da Directiva 1999/5/EC.
Română
[Romanian]
Acest echipament este in conformitate
cu cerintele esentiale si cu alte prevederi
relevante ale Directivei 1999/5/EC.
Това оборудване отговаря на съществените
Български
изисквания и приложими клаузи на
[Bulgarian]
Директива 1999/5/ЕС.
Česky
[Czech]:
Toto zařízení je v souladu se základními
požadavky a ostatními odpovídajícími
ustanoveními Směrnice 1999/5/EC.
Dansk
[Danish]:
Dette udstyr er i overensstemmelse med
de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Deutsch
[German]:
Dieses Gerät entspricht den grundlegenden
Anforderungen
und
den
weiteren
entsprechenden Vorgaben der Richtlinie
1999/5/EU.
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele
nõuetele ja teistele asjakohastele sätetele.
English:
This equipment is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami
in ostalimi relevantnimi pogoji Direktive
1999/5/EC.
Español
[Spanish]:
Este equipo cumple con los requisitos
esenciales asi como con otras disposiciones
de la Directiva 1999/5/CE.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so základnými
požiadavkami a inými príslušnými nariadeniami
direktív: 1999/5/EC.
Ελληνική
[Greek]:
Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε
τις ουσιώδεις απαιτήσεις και άλλες σχετικές
διατάξεις της Οδηγίας 1999/5/EC.
Suomi
[Finnish]:
Français
[French]:
Cet appareil est conforme aux exigences
essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
Tämä laite täyttää direktiivin 1999/5/EY
olennaiset vaatimukset ja on siinä asetettujen
muiden laitetta koskevien määräysten
mukainen.
Svenska
[Swedish]:
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og
öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Denna utrustning är i överensstämmelse med
de väsentliga kraven och andra relevanta
bestämmelser i Direktiv 1999/5/EC.
Italiano
[Italian]:
Questo apparato é conforme ai requisiti
essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/CE.
Latviski
[Latvian]:
Šī iekārta atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
[Lithuanian]:
Šis įrenginys tenkina 1999/5/EB Direktyvos
esminius reikalavimus ir kitas šios direktyvos
nuostatas.
Wireless-G Broadband Router with 2 Phone Ports
For all products, the Declaration of Conformity (DofC) is
available through one or more of these options:
•
A pdf file is included on the product’s CD.
•
A print copy is included with the product.
•
A pdf file is available on the product’s webpage.
Visit www.linksys.com/international and select your
country or region. Then select your product.
If you need any other technical documentation, see the
“Technical Documents on www.linksys.com/international”
section, as shown later in this appendix.
42
Regulatory Information
Appendix D
The following standards were applied during the
assessment of the product against the requirements of
the Directive 1999/5/EC:
•
Radio: EN 300 328 and/or EN 301 893 as applicable
•
EMC: EN 301 489-1, EN 301 489-17
•
Safety: EN 60950 and either EN 50385 or EN 50371
Dynamic Frequency Selection (DFS) and Transmit Power
Control (TPC) are required for operation in the 5 GHz
band.
DFS: The equipment meets the DFS requirements as
defined in ETSI EN 301 893. This feature is required by
the regulations to avoid interference with Radio Location
Services (radars).
TPC: For operation in the 5 GHz band, the maximum power
level is 3 dB or more below the applicable limit. As such,
TPC is not required.
CE Marking
For the Linksys Wireless-N, -G, -B, and/or -A products,
the following CE mark, notified body number (where
applicable), and class 2 identifier are added to the
equipment.
or
or
National Restrictions
This product may be used in all EU countries (and other
countries following the EU directive 1999/5/EC) without
any limitation except for the countries mentioned below:
Ce produit peut être utilisé dans tous les pays de l’UE (et dans
tous les pays ayant transposés la directive 1999/5/CE) sans
aucune limitation, excepté pour les pays mentionnés cidessous:
Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti
gli altri paesi che seguono le direttive EU 1999/5/EC) senza
nessuna limitazione, eccetto per i paesii menzionati di
seguito:
Das Produkt kann in allen EU Staaten ohne Einschränkungen
eingesetzt werden (sowie in anderen Staaten die der EU
Direktive 1999/5/CE folgen) mit Außnahme der folgenden
aufgeführten Staaten:
In the majority of the EU and other European countries,
the 2,4- and 5-GHz bands have been made available
for the use of wireless local area networks (LANs). The
table labeled “Overview of Regulatory Requirements for
Wireless LANs” provides an overview of the regulatory
requirements applicable for the 2,4‑ and 5-GHz bands.
Later in this document you will find an overview of
countries in which additional restrictions or requirements
or both are applicable.
The requirements for any country may evolve. Linksys
recommends that you check with the local authorities for
the latest status of their national regulations for both the
2,4- and 5-GHz wireless LANs.
Overview of Regulatory Requirements for Wireless LANs
or
Check the CE label on the product to find out which
notified body was involved during the assessment.
Frequency
Band (MHz)
Max Power Level
(EIRP) (mW)
2400-2483.5
100
5150-5350†
200
5470-5725†
1000
Indoor
ONLY
Indoor &
Outdoor
X
X
X
†Dynamic Frequency Selection and Transmit Power Control are
required in the frequency ranges of 5250-5350 MHz and 5470-5725
MHz.
The following countries have restrictions and/or
requirements in addition to those given in the table
labeled “Overview of Regulatory Requirements for
Wireless LANs”:
Denmark
In Denmark, the band 5150 - 5350 MHz is also allowed for
outdoor usage.
I Danmark må frekvensbåndet 5150 - 5350 også anvendes
udendørs.
Wireless-G Broadband Router with 2 Phone Ports
43
Regulatory Information
Appendix D
France
Product Usage Restrictions
For 2,4 GHz, the product should not be used outdoors
in the band 2454 - 2483,5 MHz. There are no restrictions
when used in other parts of the 2,4 GHz band when used
indoors. Check http://www.arcep.fr/ for more details.
This product is designed for indoor usage only. Outdoor
usage is not recommended, unless otherwise noted.
Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé
en extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de
restrictions pour des utilisations en intérieur dans d’autres
parties de la bande 2,4GHz. Consultez http://www.arcep.fr/
pour de plus amples détails.
This product is designed for use with the standard, integral
or dedicated (external) antenna(s) that is/are shipped
together with the equipment. However, some applications
may require the antenna(s), if removable, to be separated
from the product and installed remotely from the device
by using extension cables. For these applications, Linksys
offers an R‑SMA extension cable (AC9SMA) and an R-TNC
extension cable (AC9TNC). Both of these cables are 9
meters long and have a cable loss (attenuation) of 5 dB. To
compensate for the attenuation, Linksys also offers higher
gain antennas, the HGA7S (with R-SMA connector) and
HGA7T (with R-TNC connector). These antennas have a
gain of 7 dBi and may only be used with either the R-SMA
or R-TNC extension cable.
Applicable Power Levels in France
Location
Frequency
Range (MHz)
Power (EIRP)
Indoor
(No restrictions)
2400-2483.5
100 mW (20 dBm)
Outdoor
2400-2454
2454-2483.5
100 mW (20 dBm)
10 mW (10 dBm)
Italy
This product meets the National Radio Interface and
the requirements specified in the National Frequency
Allocation Table for Italy. Unless this 2,4-GHz wireless LAN
product is operating within the boundaries of the owner’s
property, its use requires a “general authorization”. Please
check http://www.comunicazioni.it/it/ for more details.
Questo prodotto è conforme alla specifiche di Interfaccia
Radio Nazionali e rispetta il Piano Nazionale di ripartizione
delle frequenze in Italia. Se non viene installato all’interno
del proprio fondo, l’utilizzo di prodotti Wireless LAN a 2,4 GHz richiede una “Autorizzazione Generale”. Consultare http://www.comunicazioni.it/it/ per maggiori dettagli.
Latvia
2,4 GHz Restrictions
Combinations of extension cables and antennas resulting
in a radiated power level exceeding 100 mW EIRP are
illegal.
Third-Party Software or Firmware
The use of software or firmware not supported/provided
by Linksys may result that the equipment is no longer
compliant with the regulatory requirements.
Technical Documents on
www.linksys.com/international
Follow these steps to access technical documents:
1. Enter http://www.linksys.com/international in your
web browser.
2. Select the country or region in which you live.
3. Click the Products tab.
The outdoor usage of the 2,4 GHz band requires an
authorization from the Electronic Communications Office.
Please check http://www.esd.lv for more details.
4. Select the appropriate product category.
2,4 GHz frekveču joslas izmantošanai ārpus telpām
nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv.
7. Select the type of documentation you want from the
More Information section. The document will open
in PDF format if you have Adobe Acrobat installed on
your computer.
Notes:
1. Although Norway, Switzerland and Liechtenstein are
not EU member states, the EU Directive 1999/5/EC has
also been implemented in those countries.
2. The regulatory limits for maximum output power are
specified in EIRP. The EIRP level of a device can be
calculated by adding the gain of the antenna used
(specified in dBi) to the output power available at the
connector (specified in dBm).
Wireless-G Broadband Router with 2 Phone Ports
5. Select the product sub-category, if necessary.
6. Select the product.
NOTE: If you have questions regarding
the compliance of this product or you
cannot find the information you need,
please contact your local sales office or visit
www.linksys.com/international
44
Appendix D
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with
this notice for all electronic products bearing the following
symbol:
Regulatory Information
Ceština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Wireless-G Broadband Router with 2 Phone Ports
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
45
Appendix D
Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο
αγοράσατε το προϊόν.
Wireless-G Broadband Router with 2 Phone Ports
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
46
Appendix D
Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika
li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Wireless-G Broadband Router with 2 Phone Ports
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
47
Appendix D
Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenčina (Slovene) - Okoljske informacije za stranke
v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,
označene s tem simbolom – na izdelku in/ali na embalaži – med
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.
Vaša odgovornost je, da to in preostalo električno in elektronsko
opremo odnesete na posebna zbirališča, ki jih določijo
državne ustanove ali lokalna uprava. S pravilnim odlaganjem
in recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer
ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksys.com
7102310A-JL
Wireless-G Broadband Router with 2 Phone Ports
48