Demco 55 GALLON SKID MOUNT LAWN AND GARDEN SPRAYER Operating instructions

12-04
AS20008, Rev 3
DOING OUR BEST TO PROVIDE YOU THE BEST
55 GALLON SKID MOUNT
LAWN AND GARDEN SPRAYER
OPERATORS MANUAL
ASSEMBLY
CALIBRATION
OPERATION
REPLACEMENT PARTS
READ complete manual CAREFULLY
BEFORE attempting operation.
DEMCO • Dethmers Mfg. Co. • 4010 320th St. • P.O. Box 189 • Boyden, IA 51234
PH: (712) 725-2311 • Toll Free: 1-800-543-3626 • FAX: 1-800-845-6420
www.demco-products.com
Page 1
Thank you for purchasing a Demco sprayer. We feel you have made a wise choice and hope you are
completely satisfied with your new piece of equipment. If you have any questions regarding applications
of certain solutions or chemicals, contact your chemical supplier and follow chemical manufacturer
recommendations as well as all licensing and use restrictions or regulations.
WARNING:
TO AVOID PERSONAL INJURY OR PROPERTY DAMAGE, OBSERVE
FOLLOWING INSTRUCTIONS:
Chemicals are dangerous. Know exactly what you're going to do and what
is going to happen before attempting to work with these products. Improper
selection or use can injure people, animals, plants and soil.
Always wear protective clothing such as coveralls, goggles and gloves when
working with chemicals or sprayer.
Be sure to dispose of all unused chemicals or solutions in a proper and
ecologically sound manner.
GENERAL INFORMATION
1. Unless otherwise specified, high-strength (grade5)
(3 radial-line head markings) hex head bolts are
used throughout assembly of this sprayer.
3. When placing a parts order, refer to this manual for
proper part numbers and place order by PART NO.
and DESCRIPTION.
2. Whenever terms "LEFT" and "RIGHT" are used in
this manual it means from a position behind the
sprayer and facing forward.
Table of Contents
General information ............................................................................................................. 2
Warranty Registration ........................................................................................................ 3-4
Safety, Signal Words ........................................................................................................... 5
Equipment Safety Guidelines .............................................................................................. 6
Lighting and Marking ........................................................................................................... 6
Safety Sign Locations ......................................................................................................... 7
Safety Sign Care ................................................................................................................ 8
Before Operation ............................................................................................................... 8-9
During Operation ................................................................................................................. 9
Following Operation ........................................................................................................... 10
Highway and Transport Operations ..................................................................................... 10
Performing Maintenance .................................................................................................... 11
Bolt Torque ......................................................................................................................... 12
Frame Assembly Parts Breakdown and List ....................................................................... 13
Gas Engine/Roller Pump Plumbing Parts Breakdown (w/ 12’ Boom) .................................. 14
Gas Engine/Roller Pump Plumbing Parts List and Operating Instructions (w/ 12’ Boom) .... 15
Gas Engine/Roller Pump Plumbing Parts Breakdown (w/ Truss T Boom) ............................ 16
Gas Engine/Roller Pump Plumbing Parts List and Operating Instructions (w/ Truss-T) ....... 17
Diaphragm Pump Plumbing Parts Breakdown .................................................................... 18
Diaphragm Pump Parts List, Operation and Maintenance Instructions ............................... 19
Electric Pump Plumbing Parts Breakdown and Parts List .................................................. 20
12’ Boom (DB12) Assembly Parts Breakdown and List ...................................................... 21
Truss T Boom Mounting Assembly Parts Breakdown and List ............................................ 22
Spray Wand (30L22425 18) Parts Breakdown and List ....................................................... 23
Roller Pump (C4101) Parts Breakdown and List ................................................................. 23
Electric Pump (8000 543 150) Parts Breakdown and List ................................................... 23
Optional Electric Pump (2088 343 135) Parts Breakdown and List ..................................... 23
Optional Electric Pump (10983) Parts Breakdown and List ................................................. 24
Diaphragm Pump (D19GR) Parts Breakdown and List ........................................................ 25
By-Pass Valve (8460) Parts Breakdown and List ................................................................ 26
Direct-o-valve (6B1) Parts Breakdown and List .................................................................. 26
Tee Valve (AA171) Parts Breakdown and List ..................................................................... 26
Sprayer Checklist .............................................................................................................. 27
Page 2
Warranty Registration
Dethmers Manufacturing Company
4010 320th Street • Box 189 • Boyden, Iowa 51234
Toll Free 800-54DEMCO (800-543-3626) • FAX 800-845-6420
www.demco-products.com
❍
❍
❍
❍
❍
Ag
RV
Rental
Brakes
Marine
Very
Satisfied
Satisfied
Dissatisfied
Very
Dissatisfied
How satisfied are you with our product?
❍
❍
❍
❍
How satisfied are you with the dealership/distributor sales staff?
Dealer/Distributor Name
City
❍
❍
❍
❍
How satisfied are you with the company sales staff?
❍
❍
❍
❍
How satisfied are you with the delivery?
❍
❍
❍
❍
Did you have any contact with a Demco Representative?
If YES, how satisfied were you?
YES
❍
NO
❍
❍
❍
I would recommend this product to my family and friends.
YES
NO
Would you purchase again from DEMCO?
YES
NO
Since taking delivery, have you been contacted by the dealer?
YES
NO
Did you have any problems with this DEMCO product?
If YES, are you satisfied with the company’s resolution of your problem?
YES
❍
NO
❍
❍
❍
State
Why did you purchase this product?
Please list the specific source of information prompting this purchase.
After purchasing this product, do you see any needed product improvement?
If yes, what improvement?
What other products would you like to see DEMCO offer?
Comments
Owner’s Name:
City:
Mailing Address:
State:
Zip Code:
Model#:
Serial #:
Purchase Date:
Owner’s Signature:
Please return to DETHMERS MFG. CO. By FAX or tri-folding this form to the backside, it is pre-addressed.
Page 3
Postage
Dethmers Manufacturing Company
4010 320th Street, Box 189
Boyden, Iowa 51234
Page 4
SAFETY
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS
MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING
YOUR PERSONAL SAFETY AND SAFETY OF OTHERS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
THIS SYMBOL MEANS
ATTENTION
BECOME ALERT
YOUR SAFETY IS INVOLVED!
SIGNAL WORDS
Note use of the following signal words DANGER,
WARNING, and CAUTION with safety messages.
Appropriate signal word for each has been selected
using the following guidelines:
DANGER:
Indicates an imminently hazardous situation that,
if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations typically for machine components which,
for functional purposes, cannot be guarded.
WARNING:
Indicates a potentially hazardous situation that, if
not avoided, could result in death or serious injury,
and includes hazards that are exposed when
guards are removed. It may also be used to alert
against unsafe practices.
CAUTION:
Indicates a potentially hazardous situation that, if
not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
If you have questions not answered in this manual , require additional copies, or if your manual is damaged,
please contact your dealer or Dethmers Mfg. Co., P.O. Box 189, 4010 320th Street, Boyden, IA 51234
ph: (712) 725-2311 or (712) 725-2302 Toll Free: 1-800-543-3626 Fax: (712) 725-2380
http://www.demco-products.com
Page 5
SAFETY...YOU CAN LIVE WITH IT
EQUIPMENT SAFETY GUIDELINES
Every year many accidents occur which could have been avoided by a few seconds of
thought and a more careful approach to handling equipment. You, the operator, can avoid
many accidents by observing the following precautions in this section. To avoid personal
injury, study the following precautions and insist those working with you, or you yourself,
follow them.
In order to provide a better view, certain illustrations in this manual may show an assembly
with a safety shield removed. However, equipment should never be operated in this condition.
Keep all shields in place. If shield removal becomes necessary for repairs, replace shield
prior to use.
Replace any caution, warning, danger or instruction safety decal that is not readable or is
missing. Location of such decals is indicated in this booklet.
Do not attempt to operate this sprayer under the influence of alcohol or drugs.
Review safety instructions with all users.
Operator should be a responsible adult. DO NOT ALLOW PERSONS TO OPERATE OR
ASSEMBLE THIS UNIT UNTIL THEY HAVE DEVELOPED A THOROUGH UNDERSTANDING
OF SAFETY PRECAUTIONS AND HOW IT WORKS.
To prevent injury or death, use a tractor equipped with a roll over protective system (ROPS).
Do not paint over, remove, or deface any safety signs or warning decals on your sprayer.
Observe all safety signs and practice instructions on them.
Never exceed limits of a piece of machinery. If its ability to do a job, or to do so safely is in
question-DON'T TRY IT.
LIGHTING AND MARKING
It is the responsibility of customer to know lighting and marking requirements of local highway
authorities and to install and maintain sprayer to provide compliance with regulations. Add
extra lights when transporting at night or during periods of limited visibility.
Page 6
SAFETY SIGN LOCATIONS
Types of safety sign and locations on equipment are shown in the illustration below. Good
safety requires that you familiarize yourself with various safety signs, type of warning, and
area or particular function related to that area, that requires your SAFETY AWARENESS.
WARNING
To prevent serious injury or death
This decal is located near the sprayer
lid. Replacement part # is AB21014.
ï Refer to chemical supplier and manufacturer recommendations as well as all
licensing restrictions or regulations.
ï Always wear recommended protective clothing when working with chemicals or
sprayer.
ï Be sure to dispose of all unused chemicals or solutions in proper and ecologically
sound manner. Improper use can injure people, animals, plants and soil.
04/99
Page 7
AB21014
SAFETY SIGN CARE
• Keep safety signs clean and legible at all times.
• Replace safety signs that are missing or have become illegible.
• Replacement parts that displayed a safety sign should also display current sign.
• Safety signs are available from your distributor, dealer parts department, or factory.
How to install safety signs:
• Be sure that installation area is clean and dry.
• Decide on exact position before you remove backing paper.
• Remove smallest portion of split backing paper.
• Align decal over specified area and carefully press small portion with
exposed sticky backing in place.
• Slowly peel back remaining paper and carefully smooth decal into place.
• Air pockets can be pierced with a pin and smoothed out using piece of backing paper.
BEFORE OPERATION:
• Carefully study and understand this manual.
• Do not wear loose-fitting clothing which may catch in moving parts.
• Always wear protective clothing and substantial shoes.
• It is recommended that suitable protective hearing and eye protection be worn.
• The operator may come in contact with certain materials which may require specific safety
equipment relative to handling of such materials. (Examples: extremely dusty, molds,
fungus, bulk fertilizers, etc.)
• Give sprayer a visual inspection for any loose bolts, worn parts, or cracked welds, and make
necessary repairs. Follow maintenance safety instructions included in this manual.
• Be sure there are no tools lying on or in equipment
• Do not use sprayer until you are sure that area is clear, especially around children and
animals.
• Don't hurry learning process or take sprayer for granted. Ease into it and become familiar
with your new equipment.
• Practice operation of your equipment and its attachments. Completely familiarize yourself
and other operators with its operation before using.
• Use a tractor equipped with Roll Over Protection System (ROPS) and fasten your seat belt
prior to starting engine.
• Manufacturer does not recommend usage of a tractor with ROPS removed.
Page 8
• Move tractor wheels to widest recommended settings to increase stability.
• Do not allow anyone to stand between tongue or hitch and towing vehicle when
backing up to sprayer.
DURING OPERATION
• Beware of bystanders, PARTICULARLY CHILDREN! Always look around to make sure that it
is safe to start engine of towing vehicle or move sprayer. This is particularly important with
higher noise levels and quiet cabs, as you may not hear people shouting.
• NO PASSENGERS ALLOWED- Do not carry passengers anywhere on or in the tractor or
sprayer.
• Keep hands and clothing clear of moving parts.
• Do not clean, lubricate, or adjust your sprayer while it is moving.
• When halting operation, even periodically, set tractor or towing vehicles brakes, disengage
PTO, shut off engine, and remove ignition key.
• Be especially observant of operating area and terrain- watch for holes, rocks, or other hidden
hazards. Always inspect area prior to operation.
-
DO NOT operate near edge of drop-offs or banks.
-
DO NOT operate on steep slopes as overturn may result.
-
Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.
• Pick the most level possible route when transporting across fields. Avoid edges of ditches,
gullies, and steep hillsides.
• Be extra careful when working on inclines.
• Periodically clear sprayer of brush, twigs, or other materials to prevent buildup of dry
combustible materials.
• Maneuver tractor or towing vehicle at safe speeds.
• Avoid overhead wires. Contact with overhead lines could cause serious injury or death.
• Avoid loose gravel, rocks, and holes; they can be dangerous for sprayer operation or movement.
• Allow for unit length when making turns.
• Do not walk or work under raised components or attachments unless securely supported.
• Keep all bystanders, pets, and livestock clear of work area.
• Never stand alongside of unit with engine running or attempt to start engine and/or operate
machine while standing alongside of unit.
• Never leave running equipment attachments unattended.
• As a precaution, always recheck hardware on equipment following every 100 hours of operation.
Correct all problems. Follow maintenance safety procedures.
Page 9
FOLLOWING OPERATION
• Following operation, or when unhitching, stop tractor or towing vehicle, set brakes,
disengage PTO and all power drives, shut off engine and remove ignition key.
• Store unit in an area away from human activity.
• Do not park equipment where it will be exposed to livestock for long periods of time. Damage and
livestock injury could result.
• Do not permit children to play on or around stored unit.
• Make sure all parked machines are on a hard, level surface and engage all safety devices.
HIGHWAY AND TRANSPORT OPERATIONS
• Adopt safe driving practices:
-
Keep brake pedals latched together at all times. NEVER USE INDEPENDENT BRAKING
WITH MACHINE IN TOW, LOSS OF CONTROL AND/OR UPSET OF UNIT CAN RESULT.
- Always drive at a safe speed relative to local conditions and ensure that your speed is low
enough for an emergency stop. Keep speed to a minimum.
- Reduce speed prior to turns to avoid risk of overturning.
- Always keep tractor or towing vehicle in gear to provide engine braking when going
downhill. Do not coast.
- Do not drink and drive!
• Comply with state and local laws governing highway safety and movement of farm machinery.
• Use approved accessory lighting flags and necessary warning devices to protect operators of
other vehicles on highway during transport. Various safety lights and devices are available
from your dealer.
• Use of flashing amber lights is acceptable in most localities. However, some localities prohibit
their use. Local laws should be checked for all highway lighting and marking requirements.
• When driving a tractor and sprayer under 20 mph (40 kph) day or night, use flashing amber warning
lights and a slow moving vehicle (SMV) identification emblem.
• Plan your route to avoid heavy traffic.
• Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow
bridges, intersections, etc.
• Be observant of bridge loading ratings. Do not cross bridges rated lower than gross weight at
which you are operating.
• Watch for obstructions overhead and side to side while transporting.
• Always operate equipment in a position to provide maximum visibility at all times. Make
allowances for increased length and weight of sprayer when making turns, stopping, etc.
Page 10
REMEMBER
Your best assurance against accidents is a careful and responsible operator. If there is any
portion of this manual or function you do not understand, contact your local authorized dealer
or manufacturer.
PERFORMING MAINTENANCE
• Good Maintenance is your responsibility. Poor maintenance is an invitation to trouble.
• Make sure there is plenty of ventilation. Never operate engine of towing vehicle in a closed
building. Exhaust fumes may cause asphyxiation.
• Before working on this machine, stop towing vehicle, set brakes, disengage PTO and all
power drives, shut off engine and remove ignition key.
• Be certain all moving parts and attachments have come to a complete stop before
attempting to perform maintenance.
• Always use a safety support and block wheels. Never use a jack to support machine.
• Always use proper tools or equipment for job at hand.
• Use extreme caution when making adjustments.
• Follow torque chart on page 12 in this manual when tightening bolts and nuts.
• Never use your hands to locate a hydraulic leak on attachments. Use a small piece of
cardboard or wood. Hydraulic fluid escaping under pressure can penetrate skin.
• Openings in skin and minor cuts are susceptible to infection from hydraulic fluid.
Without immediate medical treatment, serious infection and reactions can occur.
• When disconnecting hydraulic lines, shut off hydraulic supply and relieve all hydraulic
pressure.
•
Replace all shields and guards after servicing and before moving.
•
After servicing, be sure all tools, parts and service equipment are removed.
•
Do not allow grease or oil to build up on any step or platform.
•
When replacing bolts refer to owners manual.
•
Refer to bolt torque chart on page 10 for head identification marking.
•
Where replacement parts are necessary for periodic maintenance and servicing,
genuine factory replacement parts must be used to restore your equipment to original
specifications. Manufacturer will not claim responsibility for use of unapproved parts or
accessories and other damages as a result of their use.
•
If equipment has been altered in any way from original design, manufacturer does
not accept any liability for injury or warranty.
•
A fire extinguisher and first aid kit should be kept readily accessible while performing
maintenance on this sprayer.
Page 11
BOLT TORQUE
TORQUE DATA FOR STANDARD NUTS, BOLTS, AND CAPSCREWS.
Tighten all bolts to torques specified in chart unless otherwise noted. Check tightness of bolts
periodically, using bolt chart as guide. Replace hardware with same grade bolt.
NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout
assembly of equipment.
Bolt Torque for Standard bolts *
Torque Specifications
“A”
1/4”
5/16”
3/8”
7/16”
1/2”
9/16”
5/8”
3/4”
7/8”
1”
GRADE 2
lb-ft (N.m)
GRADE 5
lb-ft (N.m)
GRADE 8
lb-ft (N.m)
6
10
20
30
45
70
95
165
170
225
9
18
30
50
75
115
150
290
420
630
12
25
45
80
115
165
225
400
650
970
(8)
(13)
(27)
(40)
(60)
(95)
(130)
(225)
(230)
(300)
(12)
(25)
(40)
(70)
(100)
(155)
(200)
(390)
(570)
(850)
(16)
(35)
(60)
(110)
(155)
(220)
(300)
(540)
(880)
(1310)
Bolt Torque for Metric bolts *
“A”
Torque figures indicated are valid for
non-greased or non-oiled threads and
heads unless otherwise specified.
Therefore, do not grease or oil bolts or
capscrews unless otherwise specified
in this manual. When using locking
elements, increase torque values
by 5%.
* GRADE or CLASS value for bolts
and capscrews are identified by their
head markings.
6
7
8
10
12
14
16
18
20
22
24
CLASS 8.8
lb-ft (N.m)
CLASS 9.8
lb-ft (N.m)
CLASS 10.9
lb-ft (N.m)
9
15
23
45
78
125
194
268
378
516
654
10
18
25
50
88
140
216
-----
13
21
31
61
106
170
263
364
515
702
890
(13)
(21)
(31)
(61)
(106)
(169)
(263)
(363)
(513)
(699)
(886)
GRADE-2 GRADE-5
(14)
(24)
(34)
(68)
(118)
(189)
(293)
-----
GRADE-8
CLASS 8.8 CLASS 9.8 CLASS 10.9
8.8
Page 12
9.8
10.9
(17)
(29)
(42)
(83)
(144)
(230)
(357)
(493)
(689)
(952)
(1206)
FRAME ASSEMBLY PARTS BREAKDOWN AND PARTS LIST
3
17
16
5
19
3
14
15
5
12
5
19
4
10
13
3
9
18
3
3
9
18
5
5
18
6
11
3
FRAME ASSEMBLY PARTS LIST
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
-
PART
NO.
04340
04341
00907
00004
02592
04339
04346
04348
04347
02645
00095
04352
02802
04342
04344
04345
05034
00059
5316
04353
05785
QTY.
2
1
20
4
20
2
1
1
2
2
1
2
4
4
1
1
1
1
6
2
1
2
DESCRIPTION
Frame Side Channel
Engine/Pump Mount Plate
3/8"-16 UNC x 1" Hex Head Bolt gr. 5
5/16" Flatwasher
3/8"-16 UNC Nylon Insert Locknut
Frame Mounting Bracket
Left Hand Boom Mount
Right Hand Boom Mount (not shown)
Boom Mounting Arms
23" Saddle
55 gal. tank
3/8” x 3/4” Square Head Set Screw
5/16"-18 UNC x 4" Hex Head Bolt
5/16"-18 UNC Nylon Insert Locknut
Tank Top Mount
Hand Wand Mount
Valve Mount
Valve Mount Plate
3/8” Flatwasher
Strap Assembly
Strap
"L" Bracket
1
3
5
7
5
3
2
5
8
Please order replacement parts by PART NO. and DESCRIPTION.
Page 13
55 GALLON SPRAYER with GAS ENGINE DRIVEN ROLLER PUMP
PLUMBING BREAKDOWN for 12' BOOM
38
15
37
D
34
35
15
12
44
26
43
to 10
bo
om
36
C
16
10
9
42
6
40
27
41
39
6
6
13
40
5
13
6
12
2
7
8
B
9
6
12
10
11
4
3
A
12
15
22
12
13
10
17
1
10
19
12
14
16 10
13
18
29
20
12
12
21
15
15
32
23
25
30
24
NOTE: USE THREAD SEALANT ON
ALL THREADED FITTINGS
Page 14
45
31
28
33
GAS ENGINE DRIVEN ROLLER PUMP PLUMBING PARTS LIST
PARTS LIST
REF.
PART
NO.
NO.
1.
P55 23A
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
PL5A
5044 - 1
M1200
BEL1212
B6H
120RB
BEL3412
UV075FP
BM3400
T34F
B12H
340RB
EL114 34
BEL3434
BTT34
RVF34 80
RVF34C
RVF34GV
RVF380
RVF34B
QTY
DESCRIPTION
1 55 gallon Tank (incl. lid, agitation and
outlet fittings).
1 5î cover for tank
1 Single Agitation Wand Assembly
1 1/2" MPT Short Nipple
1 1/2" MPT x 1/2" Hose Barb Elbow
6 3/8" Hose Clamp
1/2" I.D Rubber Hose
1 3/4" MPT x 1/2" Hose Barb Fitting
3 3/4" Poly Ball Valve
6 3/4" Short Nipple
1 3/4" FPT x 3/4" Hose Barb Tee
8 3/4" Hose Clamp
3/4" I.D Rubber Hose
1 1-1/4" MPT x 3/4" Hose Barb Elbow
5 3/4" MPT x 3/4" Hose Barb Elbow
2 3/4" FPT Tee
3/4" Line Strainer w/80 mesh screen
1 3/4" Strainer Cup
1 Viton O-ring for 3/4" Strainer
1 80 Mesh Screen for 3/4" Strainer
1 Strainer Bowl
Please order replacement parts by PART NO. and DESCRIPTION.
REF.
PART
NO.
NO.
QTY
C4101GE 1
21.
C4101
1
22.
GE3HP
1
23.
02660
1
24.
04305
2
25.
00036
2
26.
04055
4
27.
02772
4
28.
02653
1
29.
02990
1
30.
02802
5
31.
04880
1
32.
07174
4
33.
00372
4
34.
05034
1
35.
8460
1
36.
6B1
1
AB6B1
37.
160GB
1
38.
00214
4
39.
A3438
1
40.
380RB
41.
A1438
1
42.
A1238
1
43. 30L22425 18 1
44. 5500 18PP 1
45.
01872
2
DESCRIPTION
Roller Pump w/3.5 HP Gas Engine
Roller Pump
3.5 HP Gas Engine (Horizontal Shaft)
Roller Pump Mounting Bracket
5/16"-18 UNC x 1/2" Hex Head Bolt
5/16" Lockwasher
1/4"-20 UNC x 1" Hex Head Bolt
1/4"-20 UNC Nylon Insert Locknuts
Pump Shaft Shield
5/16"-18 UNC x 1" Hex Head Bolt
5/16"-18 UNC Nylon Insert Locknut
Pump/Engine Coupler
1/4"-20 UNC x 3/4" Sq. Head Set Screw
5/16"-18 UNC x 1-1/2" Hex Head Bolt
6B1 Valve Mounting Plate
3/4" MPT Pressure Relief Valve
3/4" FPT Direct - o - valve
Direct - o - valve Repair Kit (see pg. 23)
160 lb. Brass Pressure Gauge
1/4" Flatwasher
3/4" MPT x 3/8" Hose Barb Fitting
3/8" I.D Rubber Hose
1/4" MGHT x 3/8" Hose Barb Fittinig
1/2" MPT x 3/8" Hose Barb Fitting
Spray Wand
Adjustable Tip (ordered separate)
Rubber Bumper
OPERATING INSTRUCTIONS
1. Fill tank with water.
2. Open the valve in the pump intake line. (A)
3. Open the pressure relief valve. (C)
4. Open Direct - o - valve. (D)
5. Open the agitation valve. (B)
6. Start engine and run pump.
7. Slowly close the pressure relief valve (C) until the desired
spraying pressure is reached with the boom spraying.
8. If adequate spraying pressure cannot be reached, slowly close the
agitation valve until the desired spraying pressure is reached.
9. Check for leaks.
10. Follow recommendation for chemical mixing and handling.
NOTE: Contact local authorized Briggs and Stratton dealer for replacement gas engines and parts.
Model no. and type no. of engine required to order parts from your Briggs and Stratton dealer.
Page 15
GAS DRIVEN ROLLER PUMP PLUMBING PARTS
BREAKDOWN FOR TRUSS-T BOOM
37
D
15
39
36
12
43
39
C
40
35
13
6 12
45 41
6 13
26
to
42
34 41
38
9
15
44
12
13
bo
6
13
om
42
41
5
6
12
6
2
7
8
B
9
6
12
10
11
4
3
A
12
15
22
12
13
10
17
1
10
19
12
14
16
10
13
18
29
20
12
12
21
15
15
32
23
25
30
24
NOTE: USE THREAD SEALANT ON
ALL THREADED FITTINGS
Page 16
27
31
28
33
GAS ENGINE DRIVEN ROLLER PUMP PLUMBING PARTS LIST
REF.
PART
NO.
NO.
1.
P55 23A
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
PL5A
5044 -1
M1200
BEL1212
B6H
120RB
BEL3412
UV075FP
BM3400
T34F
B12H
340RB
EL114 34
BEL3434
BTT34
RVF34 80
RVF34C
RVF34GV
RVF380
RVF34B
C4101
QTY
DESCRIPTION
1 55 gallon Tank (incl. lid, agitation and
outlet fittings).
1 5î cover for tank
1 Single Agitation Wand Assembly
1 1/2" MPT Short Nipple
1 1/2" MPT x 1/2" Hose Barb Elbow
6 3/8" Hose Clamp
1/2" I.D Rubber Hose
1 3/4" MPT x 1/2" Hose Barb
3 3/4" Poly Ball Valve
4 3/4" Short Nipple
1 3/4" FPT x 3/4" Hose Barb Tee
14 3/4" Hose Clamp
3/4" I.D Rubber Hose
1 1-1/4" MPT x 3/4" Hose Barb Elbow
5 3/4" MPT x 3/4" Hose Barb Elbow
1 3/4" FPT Tee
3/4" Line Strainer w/80 mesh screen
1 3/4" Strainer Cup
1 Viton O-ring for 3/4" Strainer
1 80 Mesh Screen for 3/4" Strainer
1 Strainer Bowl
1 Roller Pump
Please order replacement parts by PART NO. and DESCRIPTION.
REF.
PART
NO.
NO.
QTY
C4101GE 1
22.
GE3HP
1
23.
02660
1
24.
04305
2
25.
00036
2
26.
A1438
1
27.
01872
2
28.
02653
1
29.
02990
1
30.
02802
5
31.
04880
1
32.
07174
4
33.
00372
4
34.
04345
1
35.
8460
1
36.
AA17I
1
37.
160GB
1
38.
00523
2
39. BA1234
3
40.
02592
2
41.
A3438
3
42.
380RB
43. 30L22425 18 1
44. 5500 18PP 1
45.
00059
2
46.
F3400
1
DESCRIPTION
Roller Pump w/3.5 HP Gas Engine
3.5 HP Gas Engine (Horizontal Shaft)
Roller Pump Mounting Bracket
5/16"-18 UNC x 1/2" Hex Head Bolt
5/16" Lockwasher
1/4" MGHT x 3/8" Hose Barb
Rubber Bumper
Pump Shaft Shield
5/16"-18 UNC x 1" Hex Head Bolt
5/16"-18 UNC Nylon Insert Locknut
Pump/Engine Coupler
1/4"-20 UNC x 3/4" Sq. Head Set Screw
5/16"-18 UNC x 1-1/2" Hex Head Bolt
Valve Mounting Plate
3/4" MPT Pressure Relief Valve
3/4" FPT Tee Valve
160 lb. Brass Pressure Gauge
3/8"-16 UNC x 1-1/4" Hex Head Bolt
1/2" MPT x 3/4" Hose Barb
3/8"-16 UNC Nylon Insert Locknut
3/4" MPT x 3/8" Hose Barb
3/8" I.D Rubber Hose
Spray Wand
Adjustable Tip (ordered separate)
3/8î washer
FTG, Plug, .75î MPT, Poly Hex
OPERATING INSTRUCTIONS
1. Fill tank with water.
2. Open the valve in the pump intake line. (A)
3. Open the pressure relief valve. (C)
4. Open Tee-valve. (D)
5. Open the agitation valve. (B)
6. Start engine and run pump.
7. Slowly close the pressure relief valve (C) until the desired
spraying pressure is reached with the boom spraying.
8. If adequate spraying pressure cannot be reached, slowly close the
agitation valve until the desired spraying pressure is reached.
9. Check for leaks.
10. Follow recommendation for chemical mixing and handling.
NOTE: Contact local authorized Briggs and Stratton dealer for replacement gas engines and parts.
Need model no. and type no. of engine to order parts from your Briggs and Stratton dealer.
Page 17
DIAPHRAGM PUMP PLUMBING PARTS BREAKDOWN
33
9
20
29
38
30
28
37
31
15
to
35
bo
32
34
15
om
7
9
9
10
27
36
8
9
10
5
2
9
10
9
10
8
8
7
9
14
4
13
3
10
12
23
15
7
1
13
16
21
40
13
41
11
12
6
15 17
18
20
26
19
24
42
13
14
25
39
NOTE: USE THREAD SEALANT ON
ALL THREADED FITTINGS
Page 18
22
DIAPHRAGM PUMP PLUMBING PARTS LIST
REF.
PART
NO.
NO.
1.
P55 23A
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
PL5A
5044 -1
M1200
EL1238
580RB
UV075FP
A3438
B6H
380RB
EL114 34
BEL3434
B12H
340RB
BM3400
RVF34 80
RVF34C
RVF34GV
RVF380
RVF34B
BTT34
REF.
PART
NO.
NO.
21.
A3458
22. 9910D19GRGI
23.
GE3HP
GH4HP
24.
00372
25.
02802
26.
05596
27.
02772
28.
6B1
29. 160GBF
30.
04055
31.
00214
32.
A1238
33.
EL3438
34.
05034
35.
F3400
36.
A1438
37. 30L22425 18
38. 5500 18PP
39.
B24H
40.
02990
41.
02801
QTY
DESCRIPTION
1 55 gallon Tank (incl. lid, agitation and
outlet fittings).
1 5î cover for tank
1 Single Agitation Wand Assembly
1 1/2" MPT Short Nipple
1 1/2" MPT x 3/8" Hose Barb Elbow
5/8" I.D Rubber Hose
3 3/4" Poly Ball Valve
3 3/4" MPT x 3/8" Hose Barb
10 3/8" Hose Clamp
3/8" I.D Rubber Hose
1 1-1/4" MPT x 3/4" Hose Barb Elbow
3 3/4" MPT x 3/4" Hose Barb Elbow
4 3/4" Hose Clamp
3/4" I.D Rubber Hose
4 3/4" Short Nipple
3/4" Line Strainer w/80 mesh screen
1 3/4" Strainer Cup
1 Viton O-ring for 3/4" Strainer
1 80 Mesh Screen for 3/4" Strainer
1 Strainer Bowl
2 3/4" FPT Tee
QTY
1
1
1
1
4
5
1
4
1
1
4
4
1
1
1
1
1
1
1
2
1
1
DESCRIPTION
3/4" MPT x 5/8" Hose Barb
Diaphragm Pump w/Gear Reducer
3.5 HP Gas Engine (Horizontal Shaft)
4 HP Gas Engine (Horizontal Shaft)
5/16"-18 UNC x 1-1/2" Hex Head Bolt
5/16"-18 UNC Nylon Insert Locknut
Tee Mount Bracket
1/4"-20 UNC Nylon Insert Locknuts
Direct - o - Valve
160 lb. Brass Pressure Gauge
1/4"-20 UNC x 1" Hex Head Bolt
1/4" Flatwasher
1/2" MPT x 3/8" Hose Barb Reducer
3/4" MPT x 3/8" Hose Barb Elbow
6B1 Valve Mounting Plate
3/4" MPT Plug
1/4" MGHT x 3/8" Hose Barb
Spray Wand
Adjustable Tip (ordered separate)
1-1/4" Hose Clamp
.313 NC x 1 GR5 Hex bolt
Nut .313 NC Lock, Nylon Insert
Please order replacement parts by PART NO. and DESCRIPTION.
OPERATION INSTRUCTIONS
1. Be sure oil is halfway up the clear oil sight tube. If
necessary, fill to correct level with 30 weight nondetergent motor oil.
2. Make sure the suction hose barb is tightly screwed onto
the suction union, and that there are no air leaks on the
inlet side of the pump.
3. Check the charge pressure on the pulsation damper
before starting the pump. The pressure is checked with
a standard automotive air gauge. The pressure should
be at approximately 20% of the maximum operating
pressure with a minimum charge of 10 PSI.
4. Allow the pump to start under low pressure by removing
restrictions on the outlet of the pump. The restriction on
the pump is removed by rotating the red knob on the
control unit so that the letter A on the knob is in the 12
o'clock position.
5. Start pump and let run for approximately one minute at
low pressure. Stop pump and check the oil level in sight
glass. Add 30 weight non-detergent oil if necessary.
6. Adjust pump to desired pressure by changing the relief
valve setting on the control unit, relief valve or unloader.
First back out relief valve adjustment knob to zero. Then
rotate red bypass selector knob so that the letter C is in
the 12 o'clock position. Adjust pressure by rotating relief
valve adjustment knob to desired pressure.
MAINTENANCE INSTRUCTIONS
1. After use, flush pump with clean water.
2. Change oil and diaphragms every 500 hours. To drain
oil from the pump, remove cap from oil sight tube, turn
pump upside down and rotate the shaft until oil stops
flowing out. To fill pump with oil, slowly pour oil into sight
tube while turning the pump shaft. Turning the pump
shaft purges all the air out of the crankcase. Always
change oil when replacing diaphragms.
3. For winter storage or if a freezing condition will be
encountered, flush pump with a 50/50 mixture of water
and antifreeze.
NOTE: Contact local authorized Briggs and Stratton dealer for replacement gas engines and parts.
Need model no. and type no. of engine to order parts from your Briggs and Stratton dealer.
Page 19
ELECTRIC PUMP PLUMBING PARTS BREAKDOWN
32
17
19
16
20
21
4
13
14
23
25
30
FASTEN SWITCH (#30) AND
MOUNT (#31) TO PLATE # 26
OR TO A CONVIENIENT
LOCATION NEAR THE
24
TRACTOR SEAT
18
4
31
30
28
4
29
14
22
26
27
4
22
2
22
5
to
1
3
4
5
4
bo
om
6
8
7
9 11
10
12
13
4
14
33
15
ELECTRIC PUMP PLUMBING PARTS LIST
REF.
PART
NO.
NO.
QTY.
DESCRIPTION
1.
P55 23
1 55gal. Poly Tank
2.
PL5A
1 5î cover for tank
3.
BEL3412
1 3/4" MPT x 1/2" Hose Barb Elbow
4.
B6H
8 3/8" Hose Clamp SS
5.
120RB
1/2" I.D Rubber Hose
6.
8027
1 Swivel Nut
7. K8400 1/2 1 1/2" Hose Barb
8.
8079NY
1 50 Mesh Poly Strainer
9.
NB1614
1 1/4" MPT x 11/16" Nozzle Thread
10.
RB3814
1 3/8" MPT x 1/4" FPT Reducer Fitting
11. 8000 543 150 12 Volt Electric Pump
- 2088 343 135 12 Volt Electric 3gpm Pump
10983
1 12 Volt Electric 5gpm Pump
12.
00336
4 1/4"-20 UNC x 1-1/4" Hex Head Bolt
13.
00214
4 1/4" Flatwasher
14.
02772
7 1/4"-20 UNC Nylon Insert Locknut
15.
EL3812
1 3/8" MPT x 1/2" Hose Barb
16.
BTT12G
1 1/2" FPT Tee (Tapped for Gauge)
REF.
PART
NO.
NO.
QTY.
17.
60GB
1
18.
00955
1
19.
M1238
1
20.
03900
1
21.
EL3838
1
22.
380RB
23.
BEL1212
1
24. 5500 6 PP 1
25.
A1238
1
26.
05034
1
27.
A1438
1
28. 30L22425 18 1
29.
04055
1
30.
01013
1
31.
04755
1
32.
04764
1
33.
05020
2
DESCRIPTION
60 lb. Pressure Gauge
1/4"-20 UNC x 1" x 2” Round U-bolt
1/2" MPT x 3/8" Reducer Nipple
3/8" FPT x 3/8" FPT Valve
3/8" MPT x 3/8" Hose Barb
3/8" I.D. Rubber Hose
1/2” MPT x 1/2” Hose Barb Elbow
Adj. Tip for Spray Wand (ordered separate)
1/2" MPT x 3/8" Hose Barb
Valve Mounting Plate
1/4" MGHT x 3/8" Hose Barb Fitting
18" Hand Spray Wand
1/4”-20 UNC x 1” Hex Head Bolt Gr.5
Toggle Switch/ Nut
Switch Mount
10í Wiring Harness for electric pump
Bullet conector F/ 16-18 Ga x .180î male
Please order replacement parts by PART NO. and DESCRIPTION.
Page 20
12 FOOT BOOM PARTS BREAKDOWN
16
22
27
23
21 20
24
10
17
12
29
5
3
4
4
5
14
16
11
1
2
7
17
16
16
15
18
9
12 FOOT BOOM PARTS LIST
PART
NO.
02678
00909
00004
02802
02529
02592
02636
02637
02638
16
3
28
6
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
19
26
8
13
6
1
18
25
QTY.
DESCRIPTION
2 Boom Mounting Plate
2 5/16"-18 UNC x 1-3/8" Sq. U-bolt
4 5/16" Flatwasher
4 5/16"-18 UNC Nylon Insert Locknut
2 3/8"-16 UNC x 1-1/2" Round U-bolt
6 3/8"-16 UNC Nylon Insert Locknut
1 Center Boom Section
1 Right Boom Section
1 Left Boom Section
REF.
PART
NO.
NO.
QTY.
10.
00340
2
11.
00009
2
12.
01564
2
13.
00357
2
14.
00640
2
15.
T38
1
16.
B6H
9
17.
380RB
18.
NHT11
3
19.
NTT38
2
20
B12H
B11 114
4
21.
00337
2
22.
00068
1
23.
00062
1
24. 4193APP50 4
25.
AN1.5
4
26.
8027
4
27.
NTL38
2
28.
00059
4
29.
00967
2
DESCRIPTION
Wing Hinge Pin
Cotter Pin (1/8" x 1")
Spring
3/8"-16 UNC X 4-1/2" Tension Bolt
1/2”-13 UNC Jam Nut
3/8" Insert Tee
3/8" Gear Clamp
3/8" I.D Rubber Hose
Hose Tie
3/8" Tee Nozzle Fitting w/nut
Nozzle Nut (Included with item #19)
1-1/4" Boom Clamp Assy. (#21-#23)
1-1/4" Boom Clamp
1/4"-20 UNC x 3/4" Hex Head Bolt
1/4"-20 UNC Nut
5 PSI Ball Check Valve
Flood Jet Spray Tip
11/16" FPS Swivel Nut
3/8" Elbow Spray Nozzle Fitting (w/nut)
3/8" Flatwasher
1/2”-13 x 1-1/4” Hex Head Bolt Gr.5
Please order replacement parts by PART NO. and DESCRIPTION.
TRUSS-T BOOM PARTS BREAKDOWN
1
2
8
7
1
3
2
2
6
3
3
2
TRUSS T BOOM PARTS LIST
6
6
3
4
5
6
Page 21
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
PART
NO.
04347
00909
02678
00059
02592
05678
00004
02802
QTY.
2
4
4
8
8
4
8
8
DESCRIPTION
Boom Mounting Brackets
3/8"-16 UNC x 1-3/8" Round U-bolt
Boom Mounting Plate
3/8" Flatwasher
3/8"-16 UNC Nylon Insert Locknut
5/16"-18 UNC x 1-1/2" Sq. U-bolt
5/16" Flatwasher
5/16"-18 UNC Nylon Insert Locknut
SPRAY WAND PARTS BREAKDOWN
2
1
1
13
2
4
3
15
5
12
7
6
8
14
16
17
19
18
21 22
20
24
23
24
25
26
11
9
10
30L 22425 18
SPRAY WAND PARTS BREAKDOWN
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
PART
NO.
19684 1NYB
17013 1ZP
19818 1ZP
19819SS
19816
22138 302SS
19815
19810
19805DEL
19806FRP
17703FRP
19820 420SS
17720 420SS
7622INP
REF.
NO.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
DESCRIPTION
Housing Assembly
Screw
Screw
Washer
Spring Retainer
Spring
Spring Guide
Trigger Guide
Lock Spring Ring
Trigger Lock
Trigger
Roll Pin
Roll Pin
#6 Burr
PART
NO.
7489 302SS
7484INP
19811
*19812AL
*14255 1BU
22427 18SS
7679 1
*7678
22136
7715 18
*7490BRTF
5500 6PP
DESCRIPTION
Trigger Stop Spring
Stem Nut
Packing Screw
Gasket
Packing Cup
Stem 18"
Stem Guide Nut
Stem End
Inlet Body
18" Wand Extension
Valve Seat Sub Assembly
Adjustable Tip (ordered separately)
Not included with wand above.
Parts Kit (includes all items with *)
AB30L
Please order replacement parts by PART NO. and DESCRIPTION.
(C4101) ROLLER PUMP PARTS LIST
3
4
9
10
11
6
5
8
4
3
2
1
7
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
PART
NO.
QTY.
DESCRIPTION
1800 0001
1 Bearing Retainer Ring
0600
1 Name Plate (specify pump model #.)
BAC 37
2 Sealed Ball Bearing
*2107 0002 2 Viton Seal (standard)
0200 4101C 1 End Plate (cast iron)w/standard seal
*1720 0104 1 O-ring Gasket for End Plate
2200 0009
4 End Plate Screw
0300 4101C 1 Rotor (cast iron)and Shaft Assembly
0500 6600
1 Shaft ONLY
2230 0002
1 Rotor Set Screw
*1002 0002 4 Polypropylene Rollers (standard)
0100 4101
1 Body (cast iron) w/standard seal
3430 0158
1
Repair Kit: contains items marked (*)
Please order replacement parts by PART NO. and DESCRIPTION.
Page 22
STANDARD ELECTRIC PUMP (8000 543 150) PARTS BREAKDOWN
2
3
1
4
5
ELECTRIC PUMP (8000 543 150) PARTS LIST
REF.
NO.
1.
2.
3.
4.
5.
PART
NO.
94 382 09
94 378 00
94 391 09
94 395 06
94 385 03
DESCRIPTION
Pumphead complete w/viton parts
Upper Housing Kit
Viton Valve Kit
Santoprene Diaphragm Kit
Lower Housing Drive assembly
3.0 degree Cam
6.
94 370 03
Motor and Base Assembly
Please order replacement parts by PART NO. and DESCRIPTION.
6
OPTIONAL 3 G.P.M. ELECTRIC PUMP (2088 343 135) PARTS BREAKDOWN
OPT. ELECTRIC PUMP (2088 343 135) PARTS LIST
REF.
NO.
1.
2.
3.
4.
5.
PART
NO.
94 230 36
94 232 05
94 238 04
94 370 03
94 231 30
6.
RVB12 80
DESCRIPTION
Switch / Check valve and Upper Housing Kit
Valve Plate assembly
Diaphragm / Drive assembly
Motor
Complete Pump Head assembly (includes
parts #1,2,3) (Replaces all previous switch designs)
1/2" FPT x 1/2" Hose Barb Bowl Filter
Please order replacement parts by PART NO. and DESCRIPTION.
3
4
6
2
5
1
Page 23
5 G.P.M. ELECTRIC PUMP (10983) PARTS BREAKDOWN
OPT. ELECTRIC PUMP (10983) PARTS LIST
REF.
PART
NO.
NO.
DESCRIPTION
1.
120RB
1/2î I.D. Rubber Hose
2.
11055
Valve Housing Assembly
3.
11056
Lower Housing Assembly
4.
B6H
3/8î Hose Clamp
5.
11054
Upper Housing Assembly
6.
RVB12 80
1/2" MPT x 1/2" Hose Barb Bowl Filter
7.
BA1212
1/2" MPT x 3/8" Hose Barb
8.
BEL1212
1/2" MPT x 1/2" Hose Barb Elbow
9.
11984
Micro Switch (Inside Case)
Please order replacement parts by PART NO. and DESCRIPTION.
6
4
3
1
2
4
7
5
8
9
Page 24
DIAPHRAGM PUMP (D19GR) PARTS BREAKDOWN
49
6
70 71
76
63
72 1
73
48
13
58
75
68
5
74
8
77
69
2
10
12
11
14
46
45
51
67
13
24
23
25
21
22
13
15
29
26
41
42
44
50
17
61
47
52
66
65
64
57
13
18
9
54
53
66
68
3
55
56
40
43
30
31
32
27
34
37
36
39 38
35
28
16
DIAPHRAGM PUMP (D19GR) PARTS LIST
REF.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
34.
35.
36.
37.
38.
39.
40.
PART
REF.
PART
NO.
QTY.
DESCRIPTION
NO.
NO.
QTY.
DESCRIPTION
41. 9910 800670
1
5/8" Bypass Barb
9910 800380
2
O-ring
42. 9910 800680
1
Barb Nut
9910 800020
1
Front Housing
43. 9910 770140
1
O-ring
9910 800171
1
Crankshaft for G.R. Version
44. 9910 800480
1
Indicator Scale
9910 800160
1
Spacer Washer
45. 9910 800440
1
Relief Valve Seat Holder
9910 800150
2
Spring Locking Clip
46. 9910 800450
1
Tension Spring
9910 800370
2
Retainer Knob
47. 9910 800460
1
Relief Valve Plunger
9910 800200
1
Seal
48. 9910 800470
1
Adjustment Cap (Relief Valve)
9910 800180
1
Roller Bearing
49. 9910 480550
1
Retainer Ring
9910 800120
2
Piston
50. 9910 800010
1
Pump Body
9910 800140
2
Connecting Rod
51. 9910 800330
1
Cap for Oil Sight Glass
9910 800130
2
Connecting Rod Pin
52. 9910 800190
1
Accumulator Diaphragm
9910 480370
1
Roller Bearing
53. 9910 800230
1
Accumulator Head
9910 480440
7
O-ring
54. 9910 800650
1
Air Valve Assembly
9910 680360
1
Oil Tube Bolt
55. 9910 390340
1
O-ring
9910 800220
7
Head Bolt
56. 9910 540290
4
Bolt (8MA x 35)
9910 800100
2
Head
57. 9910 800210
2
O-ring
9910 800090
2
Diaphragm Retaining Bolt
58. 9910 800360
2
Valve Cap
9910 800350
2
Diaphragm Supporting Washer
59. 9910 800590
1
Key
9910 800085
2
Diaphragm
60. 9910 800311
1
Base Plate
9910 800110
2
Piston Sleeve
61. 9910 809060
1
Complete Relief Valve Assembly
9910 740290
1
O-ring
9910 800320
1
Oil Sight Glass
63. 9910 809050
2
Complete Valve Assembly
9910 800520
2
Barb Nut
64.
2
Check Valve Cage (Inlet)
9910 390180
1
O-ring
65. 9910 800060
4
Poppet
9910 550450
1
Barb Nut
66.
4
Tension Spring
9910 800340
1
5/8" Inlet Elbow Hose Barb
67.
2
Check Valve Seat
9910 800540
1
1/2" Outlet Hose Barb
68. 9910 200540
4
O-ring
9910 800400
1
Relief Valve Body (w/Valve Seat)
69.
2
Check Valve Cage (Outlet)
9910 550331
2
Lockwasher
70. 9910 620301
2
Plug
9910 800410
2
Bolt (6MA x 40)
71. 9910 390440
4
Nut
9910 800430
1
Floating Valve
72. 9910 800280
1
Gear
9910 800500
1
Locking Bolt
73. 9910 800810
1
Driver Gear
9910 800510
1
Locking Bolt Cap
74. 9910 800820
1
Body
9910 390330
1
Locking Pin
75. 9910 800800
1
Locating Bolt
9910 800560
1
O-ring
76. 9910 480820
1
Seal
9910 800490
1
Positioning Rod
77. 9910 620440
4
Bolt
9910 800530
1
3/8" Outlet Hose Barb
Please order replacement parts by PART NO. and DESCRIPTION.
Page 25
(8460) BYPASS VALVE PARTS BREAKDOWN
(8460) BYPASS VALVE PARTS LIST
REF.
NO.
1.
* 2.
* 3.
4.
* 5.
6.
7.
8.
9.
10.
* 11.
12.
* 13.
14.
15.
16.
17.
18.
10
9
8
7
8
6
4
5
3
2
14
1
18
13
12
11
15
16
17
PART
NO.
DESCRIPTION
8367AL
Guide Sleeve, aluminum
8373SS
Outside Spring, stainless steel
8374SS
Inside Spring, stainless steel
8371AL
Spring Retainer, aluminum
8369NY
Washer, nylon
8368SS
Adjusting Nut, stainless steel
8362AL
Bonnet, aluminum
7688ICP
Screw, steel cadium plated (4 req'd.)
5898AL
Lock Nut, aluminum
5896ALSS Adjusting Stem (sub. assembly)
8366FA
Diaphragm, fairprene
8365 304SS Stop Spring, stainless steel, type 304
8364NY
Back-up seat, nylon
8477SS
Screw, stainless steel
8389 304SS Chamber Insert, ss, type 304
8361 3/4NY Body, nylon (for 8460 3/4)
9017IZP
Clamp Plate, steel, zinc plated
8400 1/4
Pipe Plug, nylon
AB8460
Repair Kit (includes items with *)
Please order replacement parts by PART NO. and DESCRIPTION.
(6B1) DIRECT-O-VALVE PARTS BREAKDOWN
1
(6B1) DIRECT-O- VALVE PARTS LIST
REF.
PART
NO.
NO.
DESCRIPTION
1.
36301NY
Handle (Nylon)
*2.
36308SS
Groove Pin (Stainless Steel)
3.
36302PP
Body Insert (Polypropylene)
*4. 7717 2 108VI O-ring (Viton)
5.
36307SS
Washer (Type 316, Stainless Steel)
*6. 7717 2 209VI O-ring (Viton)
7.
36306SS
Spring (Type 316, Stainless Steel)
*8.
36305
Stem (Stainless Steel & Polyethylene)
9.
36303PP
Body (Polypropylene)
10.
36309SS
Retaining Clip (Stainless Steel)
AB6B1
Spare Parts Kit (includes items with *)
2
3
4
5
6
7
8
9
Please order replacement parts by PART NO. and DESCRIPTION.
10
(AA17I) TEE VALVE PARTS LIST
(AA17I) TEE VALVE
PARTS BREAKDOWN
5
4
1
3
9
6
10
11
13 14 15
8
7
12
16
17
9
2
18
19
20
22
21
REF.
PART
NO.
NO.
1.
8012 1/2SS
2.
6849IZP
2.A
15490SS
* 3.
7206IZP
* 4.
6976IZP
5.
12128IZP
* 6.
12127CE
7.
12129CE
8.
6972SS
* 9.
7980IZP
10.
12126AL
* 11.
6975BU
* 12.
5809LEA
13.
12130SS
14.
7254SS
15.
7987SS
16.
6971AL
17.
6973SS
18.
6959SS
19.
6956CE
20.
6934 6AL
* 21.
6958POL
22.
7262AL
AB17
DESCRIPTION
1/16" x 1/2" Cotter Pin, stainless steel
Handle, steel & zinc plated
Rivet, stainless steel
Rivet, steel, zinc plated
Handle Washer, steel, zinc plated
Selector Shield, steel, zinc plated
Selector Shield Tip, celcon
Spacer, celcon
Main Stem, stainless steel
Screw, steel, zinc plated (8 required)
Cover Plate, aluminum
Gasket, buna-N
Packing, thermo-leather (5 required)
Packing Gland, stainless steel
Main Spring, stainless steel
Washer, stainless steel
Selector Cam, aluminum
Guide Nut, stainless steel
Valve Spring, stainless steel (3 reqíd.)
Valve Stem, celcon (3 required)
Body, aluminum
Seat Plate, polyethylene (3 required)
Outer Adapters, aluminum ( required)
Spare Parts Kit (includes items with *)
Please order replacement parts by PART NO. and DESCRIPTION.
Page 26
SPRAYER CHECKLIST:
Downtime in fields caused by field breakdowns is costly and time consuming. Many breakdowns
can be eliminated by periodic equipment maintenance. By spending a little time running over this
checklist before seasonal spraying application time and following proper after-season care, you
can save time and money later on.
!
WARNING: To Prevent Serious Injury Or Death
•
Keep hands, feet, and loose clothing away from rotating parts.
•
Wear protective clothing recommended by your chemical and
fertilizer manufacturer when working with chemicals.
Check Before Going To The Field :
After Season Care:
1.
NOTE: It is important that when cleaning sprayer you
wear proper safety equipment. See your chemical or
fertilizer package for this information.
NOZZLES
Check tip for excessive wear by checking for grooves in
or near tip opening. Check nozzle spacing by starting at
center and working outwards. Check boom for proper
height.
2.
HOSES
Check all hoses for worn or soft spots. Be sure all hose
clamps are tightened and hoses are not kinked or
pinched. Check for leakage in any lines.
3.
TANK
Remove and clean agitator orifices. Check orifices for
excessive wear by checking for grooves in or near orifice
opening. Inspect fitting and grommets to insure they are
in good condition.
4.
5.
6.
7.
1.
After spraying chemicals, run water mixed with cleaners through tank, pump and all hose hookups. If wettable
powder dries out in system, it is very difficult to put back
into suspension and can cause malfunction, damage or
injury.
2.
When cleaned, tank should have all openings closed or
covered to keep dirt from blowing in.
3.
Pump should be flushed with soluble oil and pump ports
plugged to keep out moisture and air.
4.
CONTROLS
Check for leakage, plugging, or wear on all valves,
fittings, etc. Clean off any build up of foreign material.
Disassemble tips and rinse with water or cleaning
solution. (Appropriate for chemical sprayed).
5.
Clean tip opening with a wooden toothpick. Never use
wire or a hard object that could distort opening.
PUMP
Check to be sure pump turns freely.
6.
Be sure to dispose of all unused chemicals or solutions
in a proper and ecologically sound manner.
FRAME
Be sure all bolts are tightened.
6.
Water rinse and dry tips before storing.
REPLACEMENT PARTS
Replace all worn or damaged parts.
NOTE: DETHMERS MANUFACTURING COMPANY
does not and will not make any recommendations
concerning the application of various chemicals or
solutions. These recommendations relate to either
amount or procedure of materials applied. If you
have any questions regarding application of certain
chemicals or solutions, contact your chemical
supplier and follow chemical manufacturer
recommendations.
Page 27
DETHMERS MFG. COMPANY
P.O. BOX 189
4010 320th St., BOYDEN, IA. 51234
PH: (712) 725-2311
FAX: (712) 725-2380
TOLL FREE: 1-800-54DEMCO (1-800-543-3626)
www.demco-products.com
Page 28