English
Owner’s Manual
Italiano
Mode d'emploi
Français
Bedienungsanleitung
Deutsch
Owner’s Manual
Gebruikershandleiding
Português
Manual do proprietário
Nederlands
Manual del usuario
Español
Manuale dell'utente
Owner’s Manual
The BA-330 is a portable amp that provides stereo playback from a single unit.
It’s designed for high-quality sound, featuring up to 30W (15W + 15W) of output, four 6.5 inch (16 cm) speakers and two tweeters.
Take it anywhere
English
High quality portable stereo-output amp
You can run the BA-330 on batteries in an outdoor situation where there’s no AC outlet,
or use the included AC adaptor indoors when AC power is available.
An indicator tells you the remaining amount of battery power (p. 10).
Power-saving mode (Eco-mode) ➝ p. 10
You can switch to a power-saving mode that reduces the maximum 30W output to 15W.
This is convenient for extended use outdoors.
Easy transportation
Deutsch
Dual power supply (batteries or AC adaptor) for any location ➝ p. The wide range of inputs also allows stereo input.
Mini-concert with two guitarists ➝ p. 1
You can connect two microphones and two electric acoustic guitars for a
mini-concert with two guitarists.
Français
A variety of uses
You can connect a keyboard in stereo, along with a microphone for vocals.
Lectures or presentations ➝ p. 1
The BA-330 is a good amplification choice for a lecture or presentation.
Italiano
Keyboardist-singer ➝ p. 13
You can connect your portable audio player or CD player for
stereo playback, and independently adjust the volume of the
background music.
Español
Karaoke or background music for an event or dance
➝ p. 13
Feedback prevention ➝ p. 1
The microphone inputs provide an anti-feedback function, which suppresses acoustic feedback.
Built-in effects ➝ p. 9
Effects such as reverb and delay can be switched on/off independently for each input.
Português
Convenient functions
When the BA-330 is placed in a low position, such as on the floor, you can use the arm stand to
change its angle for greater clarity from the speaker.
It can also be mounted on a separately available speaker stand.
Connect a second unit for more output (Stereo Link) ➝ p. 1
You can increase the output by connecting two BA-330 units.
This type of setup also allows you to use up to four mic inputs and eight stereo inputs
(including AUX).
Copyright © 009 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Nederlands
Adjustable monitoring angle (Arm Stand) ➝ p. 15
USING THE UNIT SAFELY
Thank you, and congratulations on your choice of the Roland BA-330 battery powered stereo portable Amplifier.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2 ; p. 5). These sections provide
important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp
of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
INSTRUCTIONS FOR THE PREVENTION OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
About
WARNING and
WARNING
CAUTION
CAUTION Notices
About the Symbols
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The
symbol alerts the user to important instructions or
warnings. The specific meaning of the symbol is determined
by the design contained within the triangle. In the case of
the symbol at left, it is used for general cautions, warnings,
or alerts to danger.
Used for instructions intended to alert the
user to the risk of injury or material damage should the unit be used improperly.
The
symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must not
be done is indicated by the design contained within the
circle. In the case of the symbol at left, it means that the
unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with respect
to the home and all its furnishings, as
well to domestic animals or pets.
The
symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated
by the design contained within the circle. In the case of the
symbol at left, it means that the power-cord plug must be
unplugged from the outlet.
- - - - - - - - - - - - - - - - - - - - - - - - - -ALWAYS OBSERVE THE FOLLOWING- - - - - - - - - - - - - - - - - - - - - - - - - - WARNING
•
Connect mains plug of this model to a mains socket outlet
with a protective earthing connection.
•
Do not open (or modify in any way) the unit or its AC
adaptor.
•
Do not attempt to repair the unit, or replace parts within
it (except when this manual provides specific instructions
directing you to do so). Refer all servicing to your retailer,
the nearest Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
•
Never install the unit in any of the following locations.
• Subject to temperature extremes (e.g., direct sunlight in
an enclosed vehicle, near a heating duct, on top of heatgenerating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness.
•
This unit should be used only with a rack or stand that is
recommended by Roland.
WARNING
•
When using the unit with a rack or stand recommended by
Roland, the rack or stand must be carefully placed so it is
level and sure to remain stable. If not using a rack or stand,
you still need to make sure that any location you choose for
placing the unit provides a level surface that will properly
support the unit, and keep it from wobbling.
•
Be sure to use only the AC adaptor supplied with the unit.
Also, make sure the line voltage at the installation matches
the input voltage specified on the AC adaptor’s body. Other
AC adaptor’s may use a different polarity, or be designed
for a different voltage, so their use could result in damage,
malfunction, or electric shock.
•
Use only the attached power-supply cord. Also, the supplied
power cord must not be used with any other device.
•
Do not excessively twist or bend the power cord, nor
place heavy objects on it. Doing so can damage the cord,
producing severed elements and short circuits. Damaged
cords are fire and shock hazards!
•
This unit, either alone or in combination with an amplifier
and speakers, may be capable of producing sound levels that
could cause permanent hearing loss. Do not operate for a
long period of time at a high volume level, or at a level that is
uncomfortable. If you experience any hearing loss or ringing
in the ears, you should immediately stop using the unit, and
consult an audiologist.
USING THE UNIT SAFELY
WARNING
Protect the unit from strong impact.
(Do not drop it!)
•
Do not force the unit’s power-supply cord to share an outlet
with an unreasonable number of other devices. Be especially
careful when using extension cords—the total power
used by all devices you have connected to the extension
cord’s outlet must never exceed the power rating (watts/
amperes) for the extension cord. Excessive loads can cause
the insulation on the cord to heat up and eventually melt
through.
Please be sure to read and adhere to the cautionary notices
contained in the instructions that came with this product.
Please note that, depending on the manner in which BA-300
performances are carried out, you may encounter situations
where the BA-300 falls off the stand or the stand topples
over, even though you have followed all of the instructions
and advice contained within the product’s manual. For this
reason, you should always perform a safety check each time
you use the stand.
•
Always grasp only the plug on the AC adaptor cord when
plugging into, or unplugging from, an outlet or this unit.
•
At regular intervals, you should unplug the AC adaptor
and clean it by using a dry cloth to wipe all dust and other
accumulations away from its prongs. Also, disconnect the
power plug from the power outlet whenever the unit is
to remain unused for an extended period of time. Any
accumulation of dust between the power plug and the power
outlet can result in poor insulation and lead to fire.
•
Try to prevent cords and cables from becoming entangled.
Also, all cords and cables should be placed so they are out of
the reach of children.
•
Before using the unit in a foreign country, consult with your
retailer, the nearest Roland Service Center, or an authorized
Roland distributor, as listed on the “Information” page.
•
Never climb on top of, nor place heavy objects on the unit.
•
Batteries must never be recharged, heated, taken apart, or
thrown into fire or water.
•
Never handle the AC adaptor or its plugs with wet hands
when plugging into, or unplugging from, an outlet or this
unit.
•
Before moving the unit, disconnect the AC adaptor and all
cords coming from external devices.
•
Before cleaning the unit, turn off the power and unplug the
AC adaptor from the outlet (p. 7).
•
Whenever you suspect the possibility of lightning in your
area, disconnect the AC adaptor from the outlet.
•
English
•
Deutsch
This (ST-A95) for use only with Roland stand (or cart) ST-A95.
Use with other stands (or carts) is capable of resulting in
instability causing possible injury.
Français
•
•
Italiano
In households with small children, an adult should provide
supervision until the child is capable of following all the rules
essential for the safe operation of the unit.
The unit and the AC adaptor should be located so their
location or position does not interfere with their proper
ventilation.
Español
•
Immediately turn the power off, remove the AC adaptor from
the outlet, and request servicing by your retailer, the nearest
Roland Service Center, or an authorized Roland distributor,
as listed on the “Information” page when:
• The AC adaptor, the power-supply cord, or the plug has
been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been spilled onto
the unit; or
• The unit has been exposed to rain (or otherwise has
become wet); or
• The unit does not appear to operate normally or exhibits
a marked change in performance.
•
Never expose alkaline batteries or nickel-metal hydride
batteries to excessive heat such as sunshine, fire or the like.
Português
•
Do not allow any objects (e.g., flammable material, coins,
pins); or liquids of any kind (water, soft drinks, etc.) to
penetrate the unit.
Nederlands
•
CAUTION
USING THE UNIT SAFELY
CAUTION
•
If used improperly, batteries may explode or leak and cause
damage or injury. In the interest of safety, please read and
observe the following precautions (p. 6).
•
Carefully follow the installation instructions for batteries,
and make sure you observe the correct polarity.
•
Avoid using new batteries together with used ones. In
addition, avoid mixing different types of batteries.
•
Remove the batteries whenever the unit is to remain
unused for an extended period of time.
•
If a battery has leaked, use a soft piece of cloth or paper
towel to wipe all remnants of the discharge from the
battery compartment. Then install new batteries. To
avoid inflammation of the skin, make sure that none
of the battery discharge gets onto your hands or
skin. Exercise the utmost caution so that none of the
discharge gets near your eyes. Immediately rinse the
affected area with running water if any of the discharge
has entered the eyes.
•
Never keep batteries together with metallic objects such
as ballpoint pens, necklaces, hairpins, etc.
•
Used batteries must be disposed of in compliance with
whatever regulations for their safe disposal that may be
observed in the region in which you live.
•
Should you remove screws, keep them in a safe place out
of children’s reach, so there is no chance of them being
swallowed accidentally.
•
Do not remove the speaker grille and speaker by any means.
Speaker not user replaceable. Shock hazardous voltages and
currents are present inside the enclosure.
Important Notes
Power Supply: Use of Batteries
Maintenance
•
•
To clean the unit, use a dry, soft cloth; or one that is slightly dampened. Rubbing too hard in the same area can damage the finish.
•
Never use benzine, thinners, alcohol or solvents of any kind, to avoid
the possibility of discoloration and/or deformation.
Should you prefer to use batteries, please use the alkaline batteries
or nickel-metal hydride batteries.
•
When installing or replacing batteries, always turn off the power on
this unit and disconnect any other devices you may have connected.
This way, you can prevent malfunction and/or damage to speakers or
other devices.
When connecting / disconnecting all cables, grasp the connector itself—never pull on the cable. This way you will avoid causing shorts,
or damage to the cable’s internal elements.
•
To avoid disturbing your neighbors, try to keep the unit’s volume at
reasonable levels (especially when it is late at night).
•
When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to
use equivalent packaging materials.
•
Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables
can cause the sound level to be extremely low, or impossible to hear.
For information on cable specifications, contact the manufacturer of
the cable.
•
Using the unit near power amplifiers (or other equipment containing
large power transformers) may induce hum. To alleviate the problem,
change the orientation of this unit; or move it farther away from the
source of interference.
•
This device may interfere with radio and television reception. Do not
use this device in the vicinity of such receivers.
•
Noise may be produced if wireless communications devices, such as
cell phones, are operated in the vicinity of this unit. Such noise could
occur when receiving or initiating a call, or while conversing. Should
you experience such problems, you should relocate such wireless
devices so they are at a greater distance from this unit, or switch
them off.
•
Do not expose the unit to direct sunlight, place it near devices that
radiate heat, leave it inside an enclosed vehicle, or otherwise subject
it to temperature extremes. Also, do not allow lighting devices that
normally are used while their light source is very close to the unit
(such as a piano light), or powerful spotlights to shine upon the same
area of the unit for extended periods of time. Excessive heat can
deform or discolor the unit.
•
When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation)
may form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using the
unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
•
Do not allow rubber, vinyl, or similar materials to remain on the unit
for long periods of time. Such objects can discolor or otherwise
harmfully affect the finish.
•
Do not paste stickers, decals, or the like to this instrument. Peeling
such matter off the instrument may damage the exterior finish.
•
Depending on the material and temperature of the surface on which
you place the unit, its rubber feet may discolor or mar the surface.
You can place a piece of felt or cloth under the rubber feet to prevent
this from happening. If you do so, please make sure that the unit will
not slip or move accidentally.
Italiano
Placement
Español
Before connecting this unit to other devices, turn off the power to all
units. This will help prevent malfunctions and/or damage to speakers
or other devices.
Português
•
Nederlands
•
English
Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and connectors.
Rough handling can lead to malfunctions.
The AC adaptor will begin to generate heat after long hours of consecutive use. This is normal, and is not a cause for concern.
Français
•
•
•
Additional Precautions
Deutsch
Do not connect this unit to same electrical outlet that is being used
by an electrical appliance that is controlled by an inverter (such
as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the
electrical appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not practical to
use a separate electrical outlet, connect a power supply noise filter
between this unit and the electrical outlet.
Steps to Take Before Powering Up
When using batteries
* We recommend that you keep batteries installed in the unit even
though you’ll be powering it with the AC adaptor. That way, you’ll be
able to continue a performance even if the cord of the AC adaptor
gets accidentally disconnected from the unit.
Installing batteries
* To prevent malfunction or speaker damage when installing or
replacing batteries, you must switch off this unit’s power before
connecting it to other equipment.
+
-
+
+
-
-
+
Remove two screws.
.
Remove the battery
cover.
* Do not allow any foreign metal objects to touch the terminals of
the battery case. Doing so may cause the batteries to short and the
battery case may overheat or catch fire.
Regarding the batteries
Batteries that can be used
Use 8 AA alkaline batteries or AA nickel-metal hydride batteries.
+
1.
+
-
-
+
3.
+
-
* The BA-330 is not able to recharge nickel-metal hydride batteries.
Insert the batteries,
taking care to orient
them as shown in the
illustration.
Batteries must be charged using a separately sold, commercially
available charger.
Battery life (varies according to conditions of use)
mAlkaline
MAX about 8 hours
ECO about 12 hours
mNickel-metal hydride
MAX about 10 hours
Removing the battery case
Although you can replace the batteries while the battery case is
still attached, it’s easier to replace the batteries if you remove the
battery case.
1.
ECO about 15 hours
* Be aware that if nickel-metal hydride batteries are used, the battery
life-span will decrease as charging cycles are repeated.
* When operating on battery power only, the unit’s indicator (p. 10)
will become blink when battery power gets too low. Replace the
battery as soon as possible.
Remove two screws.
Cautions Regarding Batteries
* Carefully follow the installation instructions for batteries, and make
sure you observe the correct polarity.
* Avoid using new batteries together with used ones. In addition,
avoid mixing different types of batteries.
* Carefully read and observe all cautions and instructions that
accompany the batteries you use.
.
Remove the battery
case.
* If using nickel-metal hydride batteries, you must use the
combination of batteries and charger specified by the manufacturer.
* Remove the batteries whenever the unit is to remain unused for an
extended period of time.
* If a battery has leaked, use a soft piece of cloth or paper towel to
wipe all remnants of the discharge from the battery compartment.
Then install new batteries. To avoid inflammation of the skin, make
sure that none of the battery discharge gets onto your hands or
skin. Exercise the utmost caution so that none of the discharge gets
near your eyes. Immediately rinse the affected area with running
water if any of the discharge has entered the eyes.
* Never keep batteries together with metallic objects such as
ballpoint pens, necklaces, hairpins, etc.
Steps to Take Before Powering Up
When using the AC adaptor
Connecting the AC adaptor
.
Connect the included power
cord to the included AC adaptor.
Deutsch
Make sure that the [POWER]
switch is turned off.
Connect the AC adaptor to the
[DC IN] jack.
Insert it until you hear it click into place.
Français
Power cord (included)
AC adaptor
(included)
AC outlet
Español
Italiano
Connect the power cord to an
AC outlet.
Português
.
Nederlands
3.
1.
English
* You must use the included AC adaptor. Using any other AC adaptor may cause malfunction or fire.
Simple Operation Guide
Powering up and producing sound
1.
.
Set all volume
controls to “0.”
Connect your microphones, instruments, portable audio player,
or other equipment.
For details on connections, refer to “Example connections” (p. 9).
1. Make sure that the volume knobs of all connected devices are set to “0.”
. Switch on power to the connected equipment.
3.
.
Set the volume of each
channel to the middle
position.
5.
Switch on the
BA-330’s power.
Use the MASTER [VOLUME]
to adjust the volume.
Also adjust the volume of the connected equipment.
* Turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to
speakers and other devices.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before
making any connections.
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
* Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some
sound when the power is switched on, but this is normal, and does not indicate a malfunction.
Applying an effect
1.
.
Turn on the [EFFECT] switch
for the channels to which
you want to apply an effect.
Turn the [EFFECT] knob
to adjust the type and
amount of effect.
Adjusting the tone quality
Adjusting the tone of each channel
Turn the [TONE] knob of the channel
that you want to adjust.
Adjusting the high and low ranges
of the overall sound (Equalizer)
Use the [LOW] knob to boost or
cut the low-frequency range.
Use the [HIGH] knob to boost or
cut the high-frequency range.
Example Connections
Sound module
Musical instrument
(Electric acoustic guitar,
etc.)
Musical instrument
(Electric acoustic guitar,
etc.)
Synthesizer, etc.
Français
Deutsch
English
Microphone
Rhythm Machine
PCS-33
Red
White
L
L
CD player, etc.
FS-5U
Effect On/Off
Portable audio
player, etc.
FS-5L
Mute On/Off
FS-
Effect On/Off Mute On/Off
Español
R
Foot switches
Mixer, etc.
STEREO
LINK IN
Português
STEREO
LINK OUT
Set the FS-5L’s or FS-5U’s polarity switch
as shown below.
When making the connection using the FS-6,
set the POLARITY and MODE switches as
shown below.
B
A
Nederlands
R
Italiano
or
PCS-31
Other BA-330
* When connection cables with resistors are used, the volume level of equipment connected to the inputs may be low. If this happens,
use connection cables that do not contain resistors.
9
Controls and connectors
Control panel
CH1, CH2 only (monaural)
[MIC/INSTRUMENT]
switch
Set this to the appropriate position according to
whether a microphone or an instrument (a lineoutput device) is connected to CH1 and CH2.
Microphone: Set to “MIC”
Instrument: Set to “INSTRUMENT”
CH3/CH4, CH5/CH6 (stereo)
CH3/CH4 and CH5/CH6 are stereo.
Connect the following
equipment
•
•
•
•
•
Keyboards
Line-level devices
Guitars
CD players
Portable audio players, etc.
CH1, CH2 (monaural)
CH3/CH4, CH5/CH6 (stereo)
CH1, CH2 only
[ANTI-FEEDBACK] switch
Acoustic feedback will be
suppressed if this is “ON.”
For more about the antifeedback function, refer to
“Eliminating feedback” (p. 14).
Power supply related
[BATTERY CHECK/MUTE] switch
[TONE] knob
When switched on, the
indicator blinks, and
sound will no longer be
produced from the
BA-330’s speakers or
from LINE OUT.
This adjusts the tone of the instrument connected to each channel. Turning the knob toward
the right makes the tone brighter.
[EFFECT] switch
BATTERY indicator
Turning this “ON” allows the reverb, delay, or wide
effect to be applied to the channel.
When you press the
[CHECK/MUTE] switch,
this indicator shows the
amount of power remaining in the batteries.
CH [VOLUME] knob
* The remaining battery power
indication is only an approximation.
This adjusts the volume of the device connected
to each channel.
Turning the knob toward the right increases the
volume.
* The level knobs of unused channels should be
set to “0.”
Full charge
Light
Blink
Light out
Low charge
Please insert
new batteries.
Internal speakers overall
[EFFECT] knob
EQUALIZER
This knob selects the
effect type and adjusts
its depth for channels
whose [EFFECT] switch
is “ON.”
This lets you adjust the tone
by boosting or cutting the
low and high ranges independently.
Effect type
REVERB
This produces the pleasant reverberation that
accompanies a performance in a concert hall.
DELAY
This produces an echo-like effect by delaying
the sound.
WIDE
This extends the sound field to the outer edge
of the speakers, producing the sensation of being surrounded by sound.
10
[LOW] knob
This adjusts the low-frequency tone.
[HIGH] knob
This adjusts the high-frequency tone.
MASTER [VOLUME] knob
This adjusts the overall
volume of the output from
the BA-330’s speakers.
[OUTPUT POWER] switch
If this is set to “ECO,”
the volume from the
BA-330’s speakers will
be reduced, allowing
extended use when running on batteries.
With the “ECO” setting,
the maximum output
will be 15W.
[POWER] switch
This turns the BA-330’s
power on/off.
When this is on, the
POWER indicator will light.
Controls and connectors
Jack panel
Connect the following equipment
Input (INPUT) jack CH3/CH4: stereo
CH5/CH6: stereo
Connect the following equipment
• Microphone
• Musical instrument (Guitar, etc.)
•
•
•
•
•
If something is connected to both the XLR
connector and phone connector at the same
time, the phone jack will be given priority.
Wiring diagrams for these jacks are shown below. Make connections
after first checking the wiring diagrams of other equipment you
intend to connect.
TIP
HOT
RING
COLD
SLEEVE GND
HOT
GND
COLD
Keyboards
Line-level devices
Guitar
CD player
Portable audio player, etc.
If you’re using a monaural source, connect it to
L/MONO (CH4 or CH6).
You can place your
portable audio
player here.
* This will accommodate a player
of up to the following size.
English
Input (INPUT) jacks CH1, CH2: monaural
Width: 144 mm
Depth: 22 mm
AC adaptor (DC IN) jack
Deutsch
Input (AUX IN) jack
Connect the following equipment
Connect the included AC adaptor here.
* You can also connect the
commercially available cable
for an external power device.
Use the [LEVEL] knob to adjust the
volume.
The RCA phono jacks and mini-jack can be
used simultaneously.
Output (LINE OUT) jacks
FOOT SW jack
These jacks are used when you want to
connect two BA-330 units to create a
stereo system with greater output power.
For details, refer to “Connecting an additional unit to increase the output (Stereo
Link)” (p. 14).
Connect these jacks to your
mixer or recorder.
If you’re outputting in monaural,
connect the L/MONO jack.
You can use a foot switch to turn MUTE
(FS-5L) and EFFECT (FS-5U) on/off.
For details, refer to p. 9.
The EQUALIZER knobs and the
MASTER [VOLUME] knob do not
affect the LINE OUT jacks.
If only one foot switch is connected
using a monaural cable, only the MUTE
function can be switched.
Nederlands
Português
Español
Stereo link (STEREO LINK) jacks
Italiano
Français
• CD player
• Portable audio player, etc.
• Computer, etc.
11
Various Applications
Mini-concert with two guitarists
Using just a single BA-330, two singer-instrumentalists can connect two microphones and two guitars, and perform a mini-concert.
You can also apply reverb to the microphones and guitars.
Microphone 1
Microphone 2
Connection
Microphone 1 Microphone 2 Guitar 1
Guitar 1
Guitar 2
Guitar 2
Try it out
Apply reverb to the microphones and guitars
1.
Turn the [EFFECT] switch
“ON.”
.
Use the [EFFECT] knob
to adjust the amount
of reverb.
BA-330
Range of reverb
Lecture or presentation
You can connect your computer as well as your microphone so that the sound from your computer will also be heard by the audience, making your
presentation more effective.
Connection
Microphone
Computer
Microphone
Computer
BA-330
12
Various Applications
Vocalist with keyboard
You can connect your keyboard in stereo, and sing and play along with an accompaniment provided from your portable audio player.
Portable audio player
Connection
BA-330
Keyboard
Microphone
Microphone
R
L
Keyboard
English
Portable audio player
Try it out
1.
Turn the CH1 [EFFECT] switch
“ON.”
.
Use the [EFFECT] knob to
adjust the amount of reverb.
Deutsch
Apply reverb to the Microphone
Français
Range of reverb
Karaoke or background music for an event or dance
You can connect an audio device to provide background music for an event. You can also connect a microphone and enjoy karaoke.
Connection
background music for dance
Try it out
* This will
accommodate
a player of up
to the following
size.
Portable audio player
BA-330
Try it out
Connection
BA-330
Portable audio player
1.
Turn the CH1
[EFFECT] switch “ON.”
.
Use the [EFFECT]
knob to adjust the
amount of delay.
Português
Portable audio player
Apply delay to the Microphone
By applying a small
amount of delay, you can
achieve an echo-like effect.
Nederlands
Microphone
Español
Width: 144 mm
Depth: 22 mm
Portable audio player
Karaoke
Italiano
You can place your portable
audio player here.
13
Convenient Features
Suppressing feedback
What is feedback?
Feedback occurs when sound that’s being output from a speaker
enters a microphone or pickup and is amplified and output again
from the speaker, producing an unpleasant oscillation (a squealing
or howling noise).
Connecting an additional unit to
increase the output (Stereo Link)
By connecting two BA-330 units you can create a stereo PA system
with greater output power (30W + 30W).
This function is called “Stereo Link.”
You can connect Stereo Link in either of the following two ways.
• If using the input jacks of only one of the units
Using the anti-feedback function
Use one cable with a 1/4” phone plug
• If you want to use the input jacks of both units
Use two cables having 1/4” phone plugs
What is the anti-feedback function?
This function suppresses the feedback that can occur between a
guitar or microphone and the amplifier. It does so by attenuating
the sound of the frequency at which feedback is occurring.
Connection when using the input jacks of
only one unit
The BA-330 lets you suppress feedback by using a single switch.
1. Turn the [ANTI-FEEDBACK] switch “ON.”
The anti-feedback function will be applied to the microphones or
guitars connected to the CH1 and CH2 inputs.
We recommend that you turn the anti-feedback function “ON” before you begin performing, since this will prevent feedback during
your performance.
If you want to connect input sources
to the BA-330 (L)
Up to 6 input devices can be connected.
L
R
CH 1−6
AUX IN
The anti-feedback function will be optimized each time you
turn on the BA-330’s power.
Howling could be produced depending on the location of
microphones relative to speakers. This can be remedied by:
1. Changing the orientation of the microphone(s).
1. Connect the devices to the BA-330 (L).
2. Relocating microphone(s) at a greater distance from
speakers.
. Connect the STEREO LINK OUT R jack on the BA-330 (L)
3. Lowering volume levels.
and the STEREO LINK IN jack on the BA-330 (R).
3. Turn on both BA-330 (L) and BA-330 (R).
. Adjust the volume levels on all devices.
5. Adjust the BA-330 (L) and BA-330 (R) volume levels separately using their [VOLUME] knobs.
If you want to connect input sources
to the BA-330 (R)
As described in “Connecting input devices to the L-channel
BA-330,” connect the R-channel unit’s STEREO LINK OUT L jack to the
L-channel unit’s STEREO LINK IN jack.
14
Convenient Features
Connections that allow the input jacks of
both units to be used
This arrangement lets you play in stereo, making maximum use of
the two BA-330s’ mixer functions (with 12 inputs).
Using a stand
Using the BA-330’s stand
When using the BA-330 on floors, or in other low-lying positions,
then setting up and using the arm stand can make it easier to hear
the sound from the speakers.
Using the arm stand
L
R
1. Turn the BA-330 over and raise the arm stand.
CH 1−6
AUX IN
AUX IN
Arm stand
Deutsch
English
CH 1−6
1. Connect the devices to the BA-330 (L) and BA-330 (R).
. Connect the STEREO LINK OUT R jack on the BA-330 (L)
and the STEREO LINK IN jack on the BA-330 (R).
. Place the BA-330 on a flat and level surface.
3. Connect the STEREO LINK OUT L jack on the BA-330 (R)
Français
and the STEREO LINK IN jack on the BA-330 (L).
. Turn on both BA-330 (L) and BA-330 (R).
5. Adjust the volume levels on all devices.
Italiano
. Adjust the BA-330 (L) and BA-330 (R) volume levels separately using their [VOLUME] knobs.
CAUTION
• When using the arm stand, always be sure to place it so the BA-330
remains level.
• When not using the arm stand, fold it up.
• Never lift up and carry the BA-330 by holding the folding stand.
• Never place any objects on top of the BA-330 when using the arm
stand. Also, never sit or lean on the folding stand.
Português
• When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
• When folding the folding stand, be careful not to pinch your fingers.
Nederlands
Adjust the L and R volume levels separately using their MASTER
[VOLUME] knobs. You can adjust the EQUALIZER ([LOW]/[HIGH]
knobs) independently for the L and R sides. Basically, they should be
set to the same positions, but you can adjust each one as necessary
to suit the needs of a particular setup.
Español
Adjusting the volume and tone quality
15
Convenient Features
Using a speaker stand (Option: ST-A95)
By using a speaker stand (Option: ST-A95), you can mount the BA-330 at the optimal height for use as a monitor speaker or simple PA device.
Attachment procedure
WARNING
Always have at least one other person assist you when
mounting the BA-330 on a speaker stand, or when adjusting the
height of the stand while the BA-330 remains mounted on it.
• The BA-330 is designed to be used in combination with the speaker
stand manufactured by Roland (ST-A95). Please do not use any
other stands.
Be careful not to pinch your fingers, when you assemble.
• Before use, adjust the speaker stand to a height of 130 cm (51-3/16”)
or less and a leg spread of 98 cm (38-5/8”) or more, as shown in the
figure below.
Upper tube
Stopper
Height adjustment knob
Tripod knob
Tripod
130 cm or less
(51-3/16”)
1. Loosen tripod knob and open the tripod.
After opening the tripod, tighten the tripod knob again.
* The distance between lower ends of the tripod should be 98cm
as shown in figures on the below. If the tripod is not opened wide
enough, the stand may be unstable.
98 cm or more (38-5/8”)
Diameter:
112 cm or more
(44-1/8”)
• Using a speaker stand that does not meet the specifications at left
or that is adjusted to a height over 130 cm (51-3/16”), or a leg spread
of less than 98 cm (38-5/8”) may result in damage to equipment or
injury due to the stand tipping over.
• When using BA-330 with a speaker stand, the speaker stand must be
carefully placed so it is level and sure to remain stable.
Leg spread: 98 cm or
more (38-5/8”)
. Loosen height adjustment knob and make upper tube
longer.
3. Set up upper tube at the required height and insert the
stopper into the hole in upper tube (refer to following
figure).
Stopper
* Use the ST-A95 only with the stopper inserted into upper tube.
. Tighten height adjustment knob.
5. Fit the hole on the BA-330 onto upper tube.
16
• Cables connected to BA-330 should be given enough slack to prevent accidents that might result from someone tripping over them.
• To prevent accidents due to falls, do not place any object on the
BA-330 when it’s mounted on a speaker stand.
Appendix
Block Diagram
INPUT
CH1(MIC/INST)
L
R
TONE
MIC/INST
Select
LOW
TONE
POWER AMP
ANTIFEEDBACK
L
EQUALIZER
R
MIC/INST
Select
VOLUME
VOLUME
CH3/CH4 (STEREO)
L (MONO)
SPEAKER
HIGH
VOLUME
TONE
English
CH2(MIC/INST)
EFFECT
REVERB
DELAY
WIDE
LINE OUT
L (MONO)
CH5/CH6 (STEREO)
VOLUME
TONE
R
L (MONO)
VOLUME
Français
STEREO LINK OUT
R
Deutsch
R
L
AUX IN
L
Italiano
R
R
STEREO
LEVEL
Nederlands
Português
Español
STEREO LINK IN
17
Appendix
Main Specifications
BA-330:BATTERY POWERED STEREO PORTABLE
AMPLIFIER
Rated Power Output
15 W + 15 W
Nominal Input Level (1 kHz)
CH 1, CH 2 MIC: -50 dBu
CH 1,CH 2 INST: -20 dBu
CH 3/CH 4, CH 5/CH 6: -20 dBu
AUX IN: -10 dBu
STEREO LINK IN: -10 dBu
Nominal Output Level (1 kHz)
LINE OUT: -10 dBu
STEREO LINK OUT: -10 dBu
Connectors
CH 1, CH 2
Input Jacks (XLR type, 1/4” TRS phone type)
CH 3/CH 4, CH 5/CH 6
Input Jack L/MONO (1/4” phone type)
Input Jack R (1/4” phone type)
AUX IN
Input Jacks (Stereo miniature phone type, RCA phono type)
Output
LINE OUT Jack L/MONO (1/4” phone type)
LINE OUT Jack R (1/4” phone type)
STEREO LINK
STEREO LINK OUT Jacks L/MONO, R (1/4” phone type)
STEREO LINK IN Jack (1/4” phone type)
FOOT SWITCH
Speakers
16 cm (6.5 inches) x 4
Tweeter x 2
Controls
POWER Switch
Channel Controls
CH1,CH2
MIC/INSTRUMENT Switch
EFFECT Switch
TONE Knob
VOLUME Knob
CH3/CH4,CH5/CH6
EFFECT Switch
TONE Knob
VOLUME Knob
Master Controls
Equalizer
LOW Knob
HIGH KNOB
FOOT SWITCH Jack (1/4” phone type)
DC IN
DC IN Jack
Power Supply
DC 12 V: Dry Battery (LR6 (AA) type) x 8 or AC Adaptor
Current Draw
410 mA
* Expected battery life under continuous use:
m Alkaline
MAX about 8 hours
ECO about 12 hours
m Nickel-metal hydride
MAX about 10 hours
ECO about 15 hours
These figures will vary depending on the actual conditions of
use.
Dimensions
VOLUME Knob
414.6 (W) x 322.5 (D) x 508.6 (H) mm
ANTI FEEDBACK Switch
16-3/8 (W) x 12-3/4 (D) x 20-1/16 (H) inches
EFFECT Knob
BATTERY CHECK/MUTE Switch
OUTPUT POWER Switch
AUX IN Controls
LEVEL Knob
Indicator
BATTERY, BATTERY CHECK/MUTE, POWER
Weight
13.8 Kg
30 lbs 7 oz
(Excluding Battery)
Accessories
AC Cord, AC Adaptor, Owner’s Manual
Options
Carrying Bag (CB-BA330), Speaker Stand (ST-A95)
Foot Switch:BOSS FS-5L (MUTE), BOSS FS-5U (EFFECT)
BOSS FS-6
Connection Cable: PCS-31, PCS-33
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
18
Information
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar Al Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (022)-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
T.O.M.S. Sound & Music (Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
TEL: (011)417 3400
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing 100011
CHINA
TEL: (010) 6426-5050
HONG KONG
Tom Lee Music Co., Ltd. Service
Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
INDIA
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
Jl. Cideng Timur No. 15J-15O
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
VIET NAM
VIET THUONG CORPORATION
386 CACH MANG THANG TAM ST.
DIST.3,
HO CHI MINH CITY
VIET NAM
TEL: 9316540
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
CURACAO
URUGUAY
NORWAY
JORDAN
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
Roland Scandinavia Avd. Kontor
Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
MUSIC HOUSE CO. LTD. FREDDY
FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
VENEZUELA
POLAND
EASA HUSAIN AL-YOUSIFI &
SONS CO.
Al-Yousifi Service Center
P.O.Box 126 (Safat) 13002
KUWAIT
TEL: 00 965 802929
SINGAPORE
DOMINICAN REPUBLIC
SWEE LEE MUSIC COMPANY
PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
TAIWAN
ECUADOR
ROLAND TAIWAN ENTERPRISE
CO., LTD.
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
100-108 Soi Verng Nakornkasem,
New Road,Sumpantawongse,
Bangkok 10100 THAILAND
TEL: (02) 224-8821
OCEANIA
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
MARTINIQUE
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
BARBADOS
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 211
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
COSTA RICA
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar de
los Padres 01780 Mexico D.F.
MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De Instrumentos
Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868) 638 6385
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
EUROPE
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CROATIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb
TEL: (1) 466 8493
CZECH REP.
ROLAND POLSKA SP. Z O.O.
ul. Kty Grodziskie 16B
03-289 Warszawa, POLAND
TEL: (022) 678 9512
PORTUGAL
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
SYRIA
Technical Light & Sound Center
PO BOX 13520 BLDG No.17
ABDUL WAHAB KANAWATI.ST
RAWDA DAMASCUS, SYRIA
TEL: (011) 223-5384
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen, SWITZERLAND
TEL:(061)975-9987
UKRAINE
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo, UKRAINE
TEL: (03131) 414-40
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
GREECE/CYPRUS
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
aDawliah Universal Electronics
APL
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952
SAUDI ARABIA
TEL: (03) 8643601
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
SWITZERLAND
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
OMAN
SAUDI ARABIA
SPAIN
DENMARK
Chahine S.A.L.
George Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
DAN Acoustic s.r.o.
Povazská 18.
SK - 940 01 Nové Zámky
TEL: (035) 6424 330
SWEDEN
LEBANON
QATAR
SLOVAKIA
CZECH REPUBLIC DISTRIBUTOR
s.r.o
Voctárova 247/16
CZ - 180 00 PRAHA 8,
CZECH REP.
TEL: (2) 830 20270
KUWAIT
MIDDLE EAST
BAHRAIN
Moon Stores
No.1231&1249 Rumaytha
Building Road 3931, Manama 339
BAHRAIN
TEL: 17 813 942
IRAN
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021)-2285-4169
ISRAEL
TURKEY
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
TEL: (04) 3360715
NORTH AMERICA
CANADA
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way Richmond B.
C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6 CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
As of Jan. 1, 2009 (ROLAND)
For the U.K.
THIS APPARATUS MUST BE EARTHED
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or
by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
WARNING:
IMPORTANT:
For EU Countries
This product complies with the requirements of EMC Directive 2004/108/EC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For C.A. US (Proposition 65)
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For China
For EU Countries
*
5
1
0
0
0
0
9
4
7
0
1
-
0
1
*