GE Monogram® 18" Dishwasher ZBD1850NII

GE Monogram® 18" Dishwasher
ZBD1850NII
ZBD1850NII
OVERALL DIMENSIONS
17 1/2" (44.5)
26 13/16"
(68.0)
32 1/2" min
35" max
5 11/16" min
8 3/16" max
(82.5 - 88.9)
(14.5 - 20.9)
Toe kick
height
FRONT VIEW
22 1/2" (57.2)
SPECIFICATIONS
Overall Width
17 1/2" (44.5 cm)
Overall Height
32 1/2" (82.6 cm) Min
35" (88.9 cm) Max
32 1/2" min
35" max
(82.6 - 88.9)
Height at rear
Overall Depth
22 1/2" (57.2 cm)
Door Clearance
25 5/8" (14.3 cm)
Overall Dishwasher Capacity
8 Place Settings
Minimum Cabinet Width
17 5/8" (44.8 cm)
Minimum Cabinet Depth
24" (61 cm)
SIDE VIEW
Cutout Width
17 5/8" (44.8 cm) Min
18" (45.7 cm) Max
17 1/2" (44.5)
Cutout Height
32 1/2" (82.6 cm) Min
35" (88.9 cm) Max
Electrical Requirements
9.0 A
Hose Length
No more than
10' (3 m)
Voltz/Hertz/Amps
115 V, 60 Hz,
15 or 20 amp circuit
Shipping Weight
78 lb (35 kg)
3"
(7.6)
2" (5.1)
TOP VIEW
OPEN DISHWASHER
DOOR SHOWING
DOOR CLEARANCE
Dimensions in parentheses
are in centimeters unless
otherwise noted.
2" (5.1)
min
clearance
to wall
25 5/8"
(65.1)
2" (5.1)
min
clearance
to wall
Product Specification Created 3/14
ZBD1850NII
GE Monogram 18" Dishwasher
®
ZBD1850NII
INSTALLATION
NOTES
A T
he dishwasher drain
hose must be no more
than 10 feet in length
for proper drainage.
24" (61.0)
min cutout depth
32 1/2"
B A
reduced-height
installation (32-1/2"
min.) beneath a 34"
countertop can be
accomplished by
screwing in the rear legs
flush with the bottom
support, removing the
front leveling legs and
adding shims to level.
(82.55) min
underside of
counter to floor
Can be adjusted
up to 35" (88.9)
4"(10.2)
C
6"
(15.2)
ELECTRIC/
WATER
C W
ater and electrical
must be routed through
the back wall shown in
shaded area.
FLUSH CUTOUT INSTALLATION
D T
o prevent siphoning,
an air gap or high drain
loop must be used.
E A
custom panel
installation template
(Pub. No. 31-30244)
is available from
GE Parts and
Accessories
(US 800.626.2002,
Canada 800.561.3344).
CUSTOM PANEL
17 5/8" (44.8) Min
cutout width
18" (45.7) Max
cutout width
26 13/16"
(68.0)
5"
5"
(12.7)
(12.7)
C
6" (15.2)
4" (10.2)
ELECTRIC/
WATER
INSTALLATION CUTOUT FRONT VIEW
17 1/2" (44.5)
E
Product Specification Created 3/14
GE Monogram® 18" Dishwasher
ZBD1850NII
CUSTOM DISHWASHER DOOR PANEL TEMPLATE
GE PUB. NO. 31-30244
SPECIAL NOTES
Top of Panel
2-5/32"
(5.5 cm)
2-5/32"
(5.5 cm)
7-11/16"
(19.5 cm)
7-11/16"
(19.5 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
3/4" Thick Custom Panel
Template Instructions for 18"
Top Control Integrated Profile and
Monogram Dishwasher Models
STEP 4 INSTALL MOUNTING SCREWS AND SPACERS
The custom panel should be sized to your installation situation. See Step 1. For easier
installation, the custom panel and custom handle should be attached before installing the
dishwasher. Use this template to locate mounting screws and spacers on the custom panel.
IMPORTANT
• A custom handle must be installed onto the custom
panel. Install the custom handle 4-1/2" max. from
the top of the panel.
WIDTH
• The top of the custom panel must be
with the top of the door. The 1/2"minimumgap
betweenthe top of the door and the bottomof
the countertopmust be maintained.
IMPORTANT: To ensure optimum door balance
performance, the custom panel must not weigh
more than 8 lbs.
Panel width must be 17-1/2" (44.4 cm).
• If the panel widthis less than 17-1/2",it will
not cover the dishwasher frame.
Countertop
1/2" minimum
Spacer
Screws must be counter
sunk into panel
4 1/2" Max.
from top
of panel
Handle
Le panneau de finition doit avoir des dimensions appropriées pour l’installation. Consulter l’étape 1.
Pour faciliter l’installation, le panneau de finition et la poignée de finition doivent être montés avant la mise
en place du lave-vaisselle. Utiliser ce gabarit pour déterminer l’emplacement des vis de montage et
des rondelles sur le panneau de finition.
IMPORTANT
Custom
door panel
ÉTAPE 1
•
Secure
the panel to the door by inserting
the top metal spacers and bottombrackets
into the matchingslots on the dishwasher
Dishwashdoor and control panel.
er door
•
Make
sure bothmetal spacers and both
brackets engage the slots.
•
Press
the panel against the door and push
downwarduntil the metal spacers and brackets
are fully engagedinto the slots. The panel should
align evenly with the top and sides.
Trim Around
Dotted Line
HAUTEUR
Place
the custom panel on a
surface with the
appearance side down.
•
Locate
the vertical center of the panel at the top.
•
aUse
carpenter's square to draw a centerline from
top to bottom.
WARNING: Do not overtightenscrews. Excessive
tighteningof the screws could damagedoor edges.
•
•
IMPORTANT: If the template is not aligned with the top
edge of the panel, the 1/2" minimum gap will not be maintained.
This 1/2" minimum gap must be maintained to prevent condensation
and damage to the control panel from screw heads.
Mark center
screw holes
an
Use
awl to mark the screw hole locations indicated
on the template.Remove the template.
13/32"
(1 cm)
Drill 3/32"
Pilot Hole
3/32" Deep
le panneau
Si
a plus de 30 1/4po de hauteur, il empêche la
porte de s’ouvrir complètement.
le panneau
Si
a moins de 30 1/16po de hauteur, il ne couvre
pas le châssis de porte du lave-vaisselle.
ÉTAPE 2
hautLe
du panneausur mesure doit
le haut de la
porte. Il doit y avoir un espace libre d’au moins 1/2po entre le haut de la porte et le bas du revêtementde comptoi
Le panneau doit avoir au moins 23 3/4 po de largeur.
• le panneau
Si
a moins de 23 3/4po de largeur, il ne couvre
pas le châssis de porte du lave-vaisselle.
IMPORTANT : Pour que la porte fonctionne
bien, le panneau sur mesure ne doit pas
peser plus de 6,4 kilos (14 livres).
Increase
TRAÇAGE DE L’AXE
• Mettre le panneaude
sur une surface plate, le côté extérieur
vers le bas.
• Mettre le centre vertical du panneauen haut.
• Avec une équerre de menuisier, tracer un axe du haut au bas.
Increase
Decrease
ÉTAPE 3
ALIGNER LE GABARIT SUR LE PANNEAU
• Couperle gabarit suivant le pointillé,sur tous les côtés.
• Mettre le gabarit sur le panneau, aligné sur le bord supérieur et sur l’axe.
Le mainteniren place avec du ruban adhésif.
Decrease
13/32"
(1 cm)
5-29/32"
(15 cm)
5-29/32"
(15 cm)
•
Custom
panel
STEP 7 CHECK DOOR BALANCE
To check the door balance, hold the top of the
dishwasher
•
Check
the door balance by openingand closing
the door.
• the If
door drops when released, increase the
spring tension. If the door rises when released,
decrease the spring tension.
•
Using
a T25 torquedriver, adjust in the direction
shown. Adjust bothsides equally.
PIÈCES INCLUSES :
(4) Rondelles
(4) Vis nº 8 x 5/8 po à tête bombée Phillips, en acier inoxydable
(3) Vis à bois nº 8 x 1-3/4 po à tête bombée Phillips, en acier
inoxydable
(2) Ressorts pour service sévère
Maximum panel weight is
LARGEUR
8 LBS (3.6 kg).
STEP 3 ALIGN TEMPLATE TO PANEL
template
Trim
on the dottedline along all sides.
Place
the templateon the panel aligned with the top
edge and the centerline. Use tape to hold in place.
-
Le panneau doit avoir entre au moins 30 1/16 po et 30 1/4 po
de hauteur.
Custom panel
Stand
the dishwasher upright.
Open
the dishwasher door and removethe
2 plugbuttons,one on each side as shown.
•
Place
the supplied3/4"Phillips round-head
screws inside the plastic sleeve and drive
throughthe inner door and into the custom
panel.
•
Replace
the 2 plugbuttonsby pressing them
back into the plastic sleeve.
•
In Canada, call
1.800.561.3344
or visit
www.GEAppliances.ca.
Order Pub. No.
TAILLE NÉCESSAIRE Complete
POUR LE PANNEAU
SUR MESURE
31-30244.
panel
installation instructions
are included on the
template.
le panneau de finition. Installer la poignée à
moins de 11,5 cm (4-1/2 po) du haut du pan
neau.
•
•
STEP 2 DRAW CENTERLINE
•
For planning purposes, you
may order the template in
advance by calling
1.800.GE.CARES
Instructions
de gabarit pour panneau
(1.800.423.2737)
by(3/4 po)
sur mesure
épais de 19or
mm
visitingdeour
website atà réglage
pour modèle
lave-vaisselle
GEAppliances.com
in
intégré
en haut Profile et Monogram
the United States.
STEP 6 INSTALL ASSEMBLED PANEL
FOR REFERENCE
ONLY
–
NOT TO SCALE
Minimum 1/2" gap
for clearance
Bracket
Spacer Pad
A custom handle must be installed ontothe panel
before the panel is secured to the dishwasher door.
•
handle
The should be installed so that it aligns with
adjacent drawer handles, or 4-1/2"max. from the
top of the panel. Secure the handle in the same
manneras the cabinet handles. Screws must be
countersunkinto the panel.
HEIGHT
Panel height should be 26-25/32" (68 cm).
Note: The custom panel is secured to the dishwasher door
with the metal spacers, screws and brackets provided.
The metal spacers and brackets will slip into the slots
on the dishwasher door and control panel.
•
Align
the metal spacers over the top pilotholes. Ensure
the thick, recessed side is facing up.
•
Drive
the supplied1" Phillips
screws through
the metal spacers and into the panel.
•
Align
the brackets over the bottompilotholes. Ensure
the curved lip is facing up. If the back surface of the
panel is not
use the spacer pads provided.
•
Drive
the 1/2"Phillips
screws throughthe
brackets and into the panel.
STEP 5 INSTALL CUSTOM HANDLE
PARTS INCLUDED:
(2) Brackets
(4) 1/2" Phillips flat-head screws
(2) Spacer pads
(2) Metal spacers
(2) 1" Phillips flat-head screws
(2) 3/4" Phillips round-head screws
STEP 1 CUSTOM PANEL SIZE REQUIREMENTS
•
•
The custom door panel
and custom handle of your
choice should be secured
to the dishwasher before
installation begins. A
template with instructions
and installation hardware
is provided.
Top of Panel
IMPORTANT : Si le gabarit n’est pas aligné à l’extrémité du haut du panneau,
vous n’obtenez pas 1/2 po d’espace libre. Vous devez avoir un espace libre de
1/2 po pour empêcher la condensation et éviter d’endommager le panneau de
contrôle avec les têtes de vis.
• Avec un pointeau,marquerles emplacementsde trous de vis indiqués
sur le gabarit. Enlever le gabarit.
ÉTAPE 4
Drill 3/32"
Pilot Hole
3/32" Deep
INSTALLER LES VIS DE MONTAGE ET LES RONDELLES
Si l’épaisseur du panneauest inférieure à 19 mm(3/4po), il faut utiliser des vis
plus courtes. Utiliser des vis nº 8 x 1/2po (pas fournies) pour les panneauxde
13 mm(1/2po).
• Utiliser une mèche de 2,4 mm(3/32po) pour percer des trous guides à une
profondeurde 2,4 mm(3/32po) aux emplacementsmarqués.
Remarque : Le panneaude
est maintenuen place sur la porte du lavevaisselle avec des rondelles et des vis fournies. La rondelleglisse dans les
trous allongés dans la porte du lave-vaisselle.
• Visser les vis nº 8 x 5/8po à tête bombéePhillips, en acier inoxydable(fournies) à travers la rondelle et dans le panneau.
• Installer les rondelles et les vis restantes, commeindiqué,aux endroits marqués.
PARTS SUPPLIED
6-1/2"
(16.5 cm)
6-1/2"
(16.5 cm)
(2) Spacer Pads
(2) Brackets
(2) 3/4" Round-head
screws
(4) Phillips flat-head
screws
(2) Metal spacers
(2) Phillips flat-head
screws
Pub. No. 31-30244
Dwg. No. 206C1559P182
05-08 JR
Trim Around Dotted Line
CALL 1-800-626-2000
For a full-size panel template with complete panel installation instructions.
Product Specification Created 3/14
GE Monogram® 18" Dishwasher
ZBD1850NII
FEATURES AND BENEFITS
Custom Panel Model - Designed for
personalization with customer-supplied cabinetcompatible panel and custom handle
Hidden, Integrated Electronic Controls - Allow
easy activation of wash cycles: heavy wash,
normal wash, light wash, china and rinse only
Five-Level Wash System - Provides effective, yet
quiet cleaning power
Pearlescent Gray Racks with Ball-Tipped Tines Provide plenty of space and loading flexibility
Stem Safe Shelf - Allows for odd-shaped items
and delicate stemware
R
Product Specification Created 3/14