Audiovox VODDLX10 Installation guide

VODEXL10
10.1” OVERHEAD LED BACKLIT
LCD MONITOR WITH DVD
PLAYER
INSTALLATION
GUIDE
TABLE OF CONTENTS
IMPORTANT NOTICES ...................................................................................................................................................................................................................2
GENERAL SYSTEM CONFIGURATIONS (IR TRANSMIT AND RECEIVE MODES M1 OR M2) .............................................................................................3
MATERIALS INCLUDED IN THIS PACKAGE ................................................................................................................................................................................4
INSTALLING THE UNIT IN A VEHICLE .........................................................................................................................................................................................5
INSTALLING THE SNAP-ON SHROUD AND SCREEN COVER .................................................................................................................................................6
INSTALLING THE TRIM RING ........................................................................................................................................................................................................7
GENERAL VEHICLE INSTALLATION APPROACH ......................................................................................................................................................................8
VEHICLE PREPARATION ................................................................................................................................................................................................................9
CONNECTING THE DOME LIGHTS ........................................................................................................................................................................................... 10
INSTALLING THE MOUNTING BRACKET................................................................................................................................................................................. 12
INSTALLING THE VODEXL10 VIDEO SYSTEM - WIRING DIAGRAM ................................................................................................................................... 13
INSTALLING THE VODEXL10 VIDEO SYSTEM - MOUNTING THE UNIT ............................................................................................................................ 14
APPENDIX A REMOVING THE TRIM RING, SNAP-ON SHROUD AND SCREEN COVER ............................................................................................... 15
APPENDIX B INSTALLING THE OPTIONAL THICK TRIM RING ........................................................................................................................................ 16
APPENDIX C INSTALLING THE OPTIONAL GAME MODULE (MVGP1).......................................................................................................................... 17
TROUBLESHOOTING .................................................................................................................................................................................................................. 18
NOTES ............................................................................................................................................................................................................................................ 20
1
IMPORTANT NOTICES
Installation of overhead products requires careful planning and
preparation. Be extremely careful when working on a vehicle with
side curtain air bags. Do not route wires near any portion of the side
curtain air bag assemblies. This includes anchor points in A, B, C or D
pillars of the vehicle. Routing wires in these areas or running wires by
the side curtain air bags can prevent the side curtain air bag from fully
deploying which can result in personal injury to vehicle occupants. If
you have any question regarding routing in a vehicle, please contact
Audiovox Technical support at 1-800-225-6074.
WARNINGS
t Do not use any solvents or cleaning materials when cleaning the
video monitor.
t Do not use any abrasive cleaners, they may scratch the screen.
t Use only lightly dampened lint free cloth to wipe the screen if it is
dirty.
t Lock the LCD screen in fully closed position when not in use.
t Before putting on headphones, always adjust the volume setting to
OFF or lowest position.
t Remember to leave the dome light switch in the off or auto position
when the vehicle is unattended, as the dome lights, if left on, can
drain the vehicle battery.
t Do not put pressure on the screen.
t Caution children to avoid touching or scratching the screen, as it
may become dirty or damaged.
An LCD panel and/or video monitor may be installed in a motor vehicle
and visible to the driver only if the LCD panel or video monitor is used
for vehicle information, system control, rear or side observation or
navigation. If the LCD panel or video monitor is used for television
reception, video or DVD play, the LCD panel or video monitor must be
installed so that these features will only function when the vehicle is in
“park” or when the vehicle’s parking brake is applied.
Safety Precautions
For safety reasons, when changing video media, it is recommended
that the vehicle is not in motion, and that you do not allow children to
unfasten seat-belts to change video media or make any adjustments
to the system. System adjustments can be accomplished using
the remote control, while seat-belts remain fastened. Enjoy your
AUDIOVOX entertainment system but remember that the safety of all
passengers remains the number one priority.
An LCD panel and/or video monitor used for television reception,
video or DVD play that operates when the vehicle is in gear or when
the parking brake is not applied must be installed to the rear of the
driver seat where it will not be visible, directly or indirectly, to the
operator of the motor vehicle.
*** Important Notices***
When connecting power and ground in a mobile video installation,
insure that the ACC wire is fused at the point where it is connected
to the vehicle’s ACC wiring. Failure to do so can result in damage
to the vehicle if a short circuit develops between the vehicle
connection point and the mobile video product.
Please be advised that the wireless FM modulator will perform well in
most applications. However, in certain applications the quality of the
wireless signal may be less than optimal, resulting in static or strong
local station bleed through.
Licensed under one or more of the following patents, Patent Numbers
5,775,762, 5,927,784, and 6,678,892.
When installing this overhead monitor there should be no
obstructions such as extra cabling, power chokes or any other
objects placed between this overhead and supplied mounting
bracket. Failure to comply may cause damage to the overhead
monitor and will void the warranty.
2
GENERAL SYSTEM CONFIGURATIONS (IR TRANSMIT AND RECEIVE MODES M1 OR M2)
The following is intended to provide some of the system configurations that are possible with the VODEXL10 Overhead LED Backlit LCD Monitor
with DVD Player:
The VODEXL10 has an option that allows the user to select from two IR transmit and receive codes (M1 or M2). This feature can be used when using
two VODEXL10 units in the same installation or if the vehicle has an RSA (Rear Seat Audio) that uses an “A” channel headset. The VODEXL10 comes
factory set to M1. When in the M1 mode the unit will respond to remote commands when M1 is selected on the remote and will transmit audio
on the A channel. When in the M2 mode the unit will respond to remote commands when M2 is selected on the remote and will transmit audio
on the B channel.
Selecting a Monitor Code (M1 or M2)
1.
Power ON the unit and wait until M1 or M2 appears on the OSD.
PICTURE
WFMM
SETTING
M1 or M2 will appear on the screen for 4~5 seconds.
2.
Press the System Menu button on the remote control to display
the system menu to change the monitor code from M1 to M2.
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
3.
FACTORY SETTING
Use the W or X cursor buttons to select the Setting sub menu.
EXIT
4.
Use the S or T cursor buttons to select the Monitor Mode sub
menu option.
5.
Use the W or X cursor buttons to select the desired Monitor Mode
(M1 or M2), press OK to confirm the setting and the following
screen will appear.
6.
Use the S or T cursor buttons to change the selected Monitor
Mode (M1 or M2), press OK to confirm the setting.
7.
Press the System Menu button on the remote control to exit the
System Menu mode.
WARNING
SETTING THE MONITOR TO THE M2 MODE WILL
REQUIRE USING 2-CHANNEL HEADPHONES.
USE THE DOWN KEY ON THE REMOTE CONTROL
TO SELECT M2 AND PRESS OK TO SET THE
MONITOR TO M2 MODE
NOTE: If no action is taken, this menu will disappear in 10 seconds.
TO REMAIN IN THE M1 MODE PRESS OK
The two overheads can be connected together using RCA cables plugged
into the AV Input and AV Outputs connectors.
t
Plug the AV OUT of the M1 unit into the AV IN of the M2.
t
Plug the AV IN of the M1 unit into the AV OUT of the M2.
3
M1
M2
MATERIALS INCLUDED IN THIS PACKAGE
1
2
3
4
5
6
7
8
9
10
11
12
1. 10.1” TFT LCD Overhead Monitor with DVD Player
2. Hardware Package (P/N 150-1832)
M3 x 8mm Phillips Screws (P/N 100-2427)
#8 x 3/8” Self Drilling Screws (P/N 100-2397)
#2 x 1/4” Self Tapping Screws* (P/N 100-2606)
(*NOTE: For Installation of MVGP1)
M5 x 10mm Phillips Screws (P/N 100-2394)
M5 x 20mm Phillips Screws (P/N 100-2581)
M5 x 40mm Phillips Screws (P/N 100-2582)
Pry Tool (P/N 100-2424)
Slide Knob for Dome Light Switch (P/N 172-0207)
- (4 pcs)
- (4 pcs)
- (4 pcs)
- (1 pc)
- (1 pc)
CAUTION: The 10mm, 20mm and 40mm screws in the hardware kit are
provided to facilitate installation. Use extreme caution when using these
screws to avoid damage to vehicle roof or other components, wiring, etc.
3.
4.
5.
6.
7.
8.
9.
Remote Control w/ Battery (P/N 136-5326)
Mounting Bracket (P/N 108-4088)
6 Pin Power/Dome Light Harness (P/N 112-4254)
2 Pin Power Harness (P/N 112-3881)
12 Pin AV input Harness (P/N 112-4094)
5 Pin AV output Harness (P/N 112-4260)
Trim Ring - Shale (P/N 172-0198)
- Pewter (P/N 172-0199)
- Black (P/N 172-0200)
10. Snap On Cover (Screen Back) - Shale (P/N 172-0201)
- Pewter (P/N 172-0202)
- Black (P/N 172-0203)
11. Snap On Cover (Shroud) - Shale (P/N 172-0204)
- Pewter (P/N 172-0205)
- Black (P/N 172-0206)
12. Wireless Headphones w/ Batteries (P/N 136-5301)
HDIP1 (Optional)
MVGP1(Optional)
- (1 pc)
- (1 pkg)
- (8 pcs)
- (4 pcs)
- (2 pcs)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (1 pc)
- (2 pcs)
Optional Accessories
t
Game Module Package (P/N MVGP1) See Appendix C for installation
t
HDMI Harness (P/N HDIP1)
t
FM Direct Adapter (P/N FMDIRB)
FMDIRB (Optional)
4
INSTALLING THE UNIT IN A VEHICLE
Tools Required
1.
#2 Phillips Screwdriver
2.
#1 Phillips Screwdriver
3.
Utility or Razor Knife
4.
Wire Strippers
5.
Upholstery hook tool (for removal of panels as necessary)
6.
Electrical Tape
7.
Masking Tape
8.
Multimeter to verify 12 volt DC and continuity (Do not use a test
light or logic probe)
9.
Marker pen – to mark headliner, to mark trim ring if used
10. Scribe (to mark trim ring if used)
11. Miscellaneous:
t Electrical Connectors (to connect to vehicle power source,
requirements will vary from vehicle to vehicle)
t DVD Movie (to verify system operation after installation)
Preparation
Place the unit on a soft surface to avoid damaging the plastic.
Installing the Snap On Covers
The VODEXL10 is supplied with black, shale and pewter plastics to allow for a custom installation. Choose the desired color and install as follows.
2.
1.
3.
4.
Slide Knob
5.
Housing
Snap On Cover
(Screen Back Cabinet)
1 Pewter, 1 Shale, 1 Black
Snap On Cover (Shroud)
1 Pewter, 1 Shale, 1 Black
5
Pry Tool
INSTALLING THE SNAP-ON SHROUD AND SCREEN COVER
Installing the Shroud
*NOTE: Work on a soft surface to avoid damaging the plastic.
1.
Remove the double sided tape backing from the two strips on the
center section of the shroud.
2.
Hook the shroud over the dome light and align the shroud tabs 1
with the eight openings around the rim of DVD player 2 .
3.
Slide the shroud down until the shroud completely covers the
DVD player and that all eight tabs snap into all eight openings
around the DVD player 1 , 2 .
4.
Apply pressure to the center section of the shroud in the area of
the double sided tape to ensure that the tape adheres.
5.
Locate the Slide Knob 3 in the hardware package and press it onto
the dome light switch 4 on the side of the DVD player.
Installing the Screen Cover
1.
Open the LCD screen.
2.
Hook the two tabs “A” (as shown) on the bottom edge of the
screen.
3.
Carefully snap the opposite side over the hinge.
NOTE: If the wrong color Shroud and Screen Cover is installed, refer to
Appendix A of this manual for instructions to change the Shroud and
Screen Cover color.
6
INSTALLING THE TRIM RING
The trim ring is attached to the video monitor using the perimeter screw bosses. It is important that the screws used in this installation are not over
tightened, and that the video monitor and trim ring are mounted in such a way that the assembly does not distort (or bend) when the mounting
screws are tightened.
There are two Trim Ring options for mounting the VODEXL10, one is to use the supplied Trim Ring for all vehicles with flat headliner mounting areas
(no contour) or a thick Trim Ring (not supplied) that can be cut to fit the contour of a headliner that is not flat (see Appendix B of this manual).
NOTE: The trim rings supplied with this unit are not designed to be trimmed.
Installing the Trim Ring
1. Turn the DVD Player over on a surface with protective covering to prevent scratches.
2. Place the trim ring onto the DVD Player. Align the pins on the trim ring with the holes in the metal chassis plate.
Trim Ring
3.
4.
DVD
PLAYER
Locate the eight (8) M3 x 8mm screws in the hardware kit.
Using a screwdriver, install the eight (8) M3 x 8mm screws into the locations marked “A” shown in the figure below.
NOTE: Use caution tightening screws as the threads may strip in the DVD Player.
(A)
(A)
TRIM RING SCREW
(A)
(A)
(A)
(A)
(A)
(A)
7
(A) M3 X 8mm Screw
(QTY 8)
TRIM
RING
ON DVD
PLAYER
GENERAL VEHICLE INSTALLATION APPROACH
1.
Decide upon system configuration and options that will be installed (i.e.: what components, Video Game, external amp).
2.
Review all manuals to become familiar with electrical requirements and connections.
3.
Decide upon mounting locations of all components and method of mounting.
4.
Prep the vehicle by removing any interior trim necessary to gain access to vehicle’s wiring as well as all areas where interconnecting wire
harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim components etc.), this should
be done now as well.
5.
Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on page 13 of this manual, as well as the
wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp
edges and is routed in such a manner that wiring is not pinched when all components and interior trim are fully installed. Be sure to leave
enough slack in the wiring at each component to allow working room. Avoid routing wiring near or over airbag wiring or airbags.
6.
Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations.
7.
Connect all components together (electrically) and verify proper operation of all system functions. Note: This is best done BEFORE,
components have been permanently mounted.
8.
After verifying proper operation of the system proceed to mount each component.
9.
When all components are mounted recheck the function of the entire system again to ensure that no wiring was pinched or connected
improperly during final installation.
8
VEHICLE PREPARATION
1.
Locate an accessory +12v power source with a good ground. These wires can be found at the ignition switch or fuse-box.
Power Source
t +12v when the key is in the ACC and run positions.
t 0v when the key is OFF.
NOTE: Always fuse the ACC +12V at the source where it is connected to the vehicle.
2.
The mounting method and location will vary from vehicle to vehicle, the only focus of this manual is the installation of the VODEXL10.
3.
Generally, the best location for the video monitor is where the vehicle’s factory dome light is installed. The monitor should be located in
such a manner that it can be comfortably viewed by rear seat passengers.
NOTE: Never install the monitor in a place within the driver’s view. This is not only dangerous, but it is also illegal in many states.
4.
Once the mounting location of the monitor has been determined, additional preparation work may be necessary, depending on the vehicle
structure and installation method. Some of the steps that may be required are:
a. Removal of the vehicle’s dome light.
b. Cutting an opening in the headliner to install the mounting bracket.
c. If the optional Thick Trim Ring will be used, it may have to be trimmed to fit the contour of the vehicle’s headliner. Refer to Appendix B
Installing the Optional Thick Trim Ring.
9
CONNECTING THE DOME LIGHTS
The dome lights in the video monitor require three connections to the vehicle’s wiring. There are two common types of dome light circuits used,
positive switched systems or negative switched systems. Positive switched systems supply voltage to the interior lights to turn ON; negative
switched systems apply ground to illuminate the bulbs.
To determine which system you have to locate the wires at the dome light:
t
On a positive switched system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When the light is
activated, one of these wires will switch to +12 VDC. This is the vehicle’s switching wire.
t
On a negative switched system, with all the doors closed and the lights out, both wires at the dome light will rest at +12 VDC. When the light
is activated, one of these wires will switch to ground. This is the vehicle’s switching wire.
For positive switched systems, connect the Purple / Brown (Lamp Auto) wire to the vehicle’s switched wire. Then connect the Red / Black (Lamp
ON) wire to a fused constant 12 volt source and the Black / Red (Lamp Common) wire to a good ground. Positive switched systems are commonly
found on Ford vehicles.
For negative switched systems, connect the Purple / Brown (Lamp Auto) wire to the vehicle’s switched wire. Then connect the Red / Black (Lamp
On) wire to a good ground and the Black / Red (Lamp Common) wire to a fused constant 12 volt source. Negative switched systems are commonly
found on General Motors and import vehicles.
NOTE: Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge Caravan, may require that the
Purple / brown (Lamp Auto) wire be connected to the door pin switch wire, as the additional current draw of the monitor’s lights may not be
supported by the output of the vehicle’s body control computer.
After wiring the dome lights make sure the dome lights operate properly with doors opening and closing and that they are not always
on. Do not leave the dome lamp switch on the DVD overhead in ON position as this will drain the battery over time.
10
CONNECTING THE DOME LIGHTS
Positive Switched Dome Lighting
To 3 pin
connector
on Monitor
Red/Black-Lamp ON
Black/Red-Lamp Common
Purple/Brown-Lamp Auto
Negative Switched Dome Lighting
To
constant
+12 VDC
To 3 pin
connector
Red/Black-Lamp on
Black/Red-Lamp common
Purple/Brown-Lamp Auto
To
constant
+12 VDC
Fused
Fused
Factory Dome Light Circuit
To
constant
+12 VDC
To
constant
+12 VDC
Factory Door Ajar
Switch or Body
Control Computer
Factory Door Ajar
Switch or Body
Control Computer
11
INSTALLING THE MOUNTING BRACKET
Installing the Mounting Bracket
1.
2.
NOTE: The headliner may need to be cut to install the bracket. When
Once all the pre-wiring is complete, locate:
cutting the headliner, make sure no wires above the headliner are cut.
t Mounting Bracket
t (4) #8 x 3/8” Self-Drilling Screws
Carefully align the Mounting Bracket in the location it is to be 3. While holding the Mounting Bracket in place, install the
4- #8 x 3/8” Self-Drilling Screws.
installed with direction arrow facing the front of the vehicle (make
CAUTION: Be sure that the Self-Drilling Screws do not pierce the
sure there is nothing between the Mounting Bracket and Roof
outer roof skin when fully fastened to the Roof Cross-Member.
Cross-Member).
Roof
Roof Cross-Member
Headliner
Front
of
Vehicle
Mounting Bracket
Mounting Bracket
(Top view of Bracket)
Direction Arrow
*Self-Drilling Screws
(4 x Self-Drilling Screws - #8 x 3/8”)
Bracket
Mounting
Holes
*CAUTION: Use extreme caution when using the
Self-Drilling Screws to avoid damage to vehicle
roof or other components, wiring, etc.
12
INSTALLING THE VODEXL10 VIDEO SYSTEM - WIRING DIAGRAM
1.
Connect the dome light wires as shown on pages 10 and 11 of this 4.
install manual.
2.
Connect the wires of the 2 pin Power Harness to the vehicle’s
electrical system by tapping into an accessory hot line and a good 5.
ground. NOTE: This connection must be fused at the vehicle
connection point.
3.
If connecting to an external source, plug in the 12 pin AV Input
Harness (P/N 112-4094) in the location shown. Connect RCA
cables (not supplied) to the external source’s AV Output.
If connecting to a second screen AUX Input or head unit AUX
Input, plug in the 5 pin AV Output Harness (P/N 112-4260) in the
location shown and connect RCA cables (not supplied) to the AV
Input of the second screen or head unit.
Connect the 2 pin connector on the Power Harness to the 2 pin
connector on the Power/Dome Light Harness. Plug the Power/ 6. Verify all system functions before permanently mounting the unit.
Dome Light harness into the unit in the location shown.
*NOTE: The antenna has been designed for optimal performance. When
installing the unit, position the antenna for best reception.
WIRING DIAGRAM
HDMI 2 Pigtail Harness (optional)
(HDIP1)
6 Pin Power/Dome Light Harness
(P/N 112-4254)
2 Pin
Power Harness
(P/N 112-3881)
Dome Light
Power Source
12 Pin AV Input Harness
(P/N 112-4094)
5 Pin AV Output Harness
(P/N 112-4260)
Optional Relay Box FMDIRB
FM ANT.
* 2 Pin FM Antenna
13
A/V Sources:
t
DVD / CD
t
USB Input
t
HDMI1 Input
t
HDMI2 Input
t
Media (e.g. iPod, iPhone, iPad)
t
AV - Signal Harness (P/N 112-4094)
to the 3 RCA Jack Pigtail is used for
AV Input.
t
AUX - AUX Input
t
DTV
t
Game
INSTALLING VODEXL10 VIDEO SYSTEM - MOUNTING THE UNIT
Installing the VODEXL10 System
1.
2.
Make all electrical connections.
Attach the VODEXL10 unit to the mounting bracket using four M5 screws.
CAUTION: The M5 screws are supplied in three different lengths (10mm, 20mm and 40mm) to facilitate proper installation. Use extreme caution
when using these screws to avoid damage to vehicle roof or other components, wiring, etc.
CAUTION: Do not trap any wiring between the bracket and the unit.
Roof
Headliner
Front
of
Vehicle
Mounting Bracket
Mounting Bracket
Video Unit
VODEXL10
4 x M5
Screws
NOTE: Do not over torque or
over tighten M5 screws.
Mounting Holes
14
APPENDIX A
REMOVING THE TRIM RING, SNAP-ON SHROUD AND SCREEN COVER
This section is intended for situations where the color of the Shroud, Screen Cover and Trim Ring need to be changed after the unit is setup for
installation. NOTE: Work on a soft surface to avoid damaging the plastic.
Removing the Screen Back Cover
1.
2.
3.
4.
Starting from the back of the unit, carefully insert the supplied
pry tool between the Housing and Screen Back Cover
Press the pry tool to release the Screen Back Cover.
While lifting the Screen Back Cover, slide the pry tool around to
the attaching areas and press the pry tool to release the Screen
Back Cover.
Remove the Screen Back Cover and discard.
Removing the Trim Ring
1.
2.
(8)
Remove the Trim Ring screws ((8) M3 x 8mm screws).
NOTE: Do not Discard Screws! These screws are used to attach the
new Trim Ring.
Remove the Trim Ring and discard.
TRIM RING SCREW
Removing the Shroud
1.
2.
3.
4.
(1)
Using the supplied pry tool, remove the slide knob from the
dome light switch located on the side of the DVD player.
NOTE: Do not Discard knob! The knob is reused.
Open the screen and insert the supplied pry tool between the
Housing and Shroud and disengage the tape on the center
section of the shroud.
Press the pry tool to disengage the attaching Shroud clips.
Continue disengaging the attaching areas around the unit
removing the Shroud and discard.
15
(7)
(2)
(6)
(3)
(5)
(4)
(8) M3 X 8mm Screws
APPENDIX B
INSTALLING THE OPTIONAL THICK TRIM RING
This section covers only special installation considerations for the optional thick trim ring installation. If the video monitor is to be installed in a
vehicle with the thick trim ring, it may need to be trimmed to fit the contour of the vehicle Headliner.
Important NOTES before installing the thick trim ring:
t There should be a gap between the headliner and the outer flange of the video monitor.
t The trim ring should be cut to fill this gap.
1. Apply masking tape to the outside of the thick trim ring.
3 Cut the trim ring using a sharp utility knife or shears. Make the
2. Mark the cut line to follow the necessary contour of the roof.
cut in several passes over the marked line, each time cutting a
The suggested method of marking is as follows:
little deeper. It is not necessary to cut completely through the
plastic, the cut only need be over 50% of the wall thickness of
a. First mark the narrowest point of the trim ring on the
the plastic. By bending the cut back and forth several times,
masking tape. Be careful to consider not only vertical
the plastic will break cleanly at the cut.
location, but fore-aft location.
4. Check the fit of the trimmed console and make any minor
b. Using the handle of a screwdriver, make a “transfer marking
adjustments necessary.
tool”. See diagram below. Place the tool against the roof
and the marker against the masking tape on the trim ring.
Trace the cut to be made around the entire perimeter of
the trim ring.
THICK TRIM RING
PART NUMBERS
Shale - 1187270PL
Headliner
Cut line
Tape marker to screwdriver handle.
Starting at your mark for the lowest point,
trace the contour of the roof around the
perimeter of the trim ring.
Lowest point mark
16
Pewter-
1187271PL
Black-
1187272PL
APPENDIX C
INSTALLING THE OPTIONAL GAME MODULE (MVGP1)
This section is intended as an installation guide to connect the MVGP1 Game Module to the VODEXL10 video system.
NOTE: The MVGP1 Game Module is sold separately and is supplied with its own instruction manual.
Installing the MVGP1 Game Module
1.
Turn the DVD Player over on a surface with protective covering
to prevent scratches.
2.
Begin looping the excess MVGP1 Game Module harness under
the protective top plate towards the back of the DVD player as
shown.
3.
Place the MVGP1 Game Module onto the mounting standoffs.
4.
Locate the two #2 x 1/4 Phillips Self Tapping Screws
(P/N 100-2606) in the VODEXL10 hardware kit.
5.
MVGP1 Game Module
Harness loop
Back of Unit
Screw
Using a screwdriver, install the two screws into the two locations
shown.
MVGP1
Screw
NOTE: Use caution tightening screws as the threads may strip in
the DVD Player.
6.
Insert the 8-pin connector of the MVGP1 Game Module harness
into the location shown.
7.
Verify Game Module and Game Controllers function properly
(refer to Owner’s Manual).
Top of VODEXL10 Video System
17
8-Pin
Harness
Connector
TROUBLESHOOTING
SYMPTOM:
REMEDY:
No power at video monitor
t Verify +12 VDC on the Red wire at 2 Pin Power Harness behind the video
monitor. Verify a ground connection with a continuity test from a known
good ground to the black wire at the 2 Pin Power Harness.
Power but no video or sound
t Verify that the correct source is selected (DVD, USB, HDMI1, HDMI2, Media,
AV, AUX, DTV, Game). Verify that the source is on and playing a known good
media.
Disc will not play or wrong region is displayed
t Check the type of disc you put into disc slot and is inserted in the correct
position. NOTE: The DVD system only plays digital video discs, audio CDs and
MP3s.
t Both the unit and the disc are coded by region. If the regional codes don’t
match, the disc can’t be played. This DVD player is set to Region 1.
IR Wireless Headphones do not work
t Check if batteries are installed correctly.
t Make sure that the headphone batteries are fresh.
t Check if Power Button lights up when pressed. If Power Button does not light
up when pressed, change batteries.
t If using Dual Channel Wireless Headphones, make sure the correct channel
is selected.
t Make sure the IRT power is ON. Press the IRT ON/OFF button on the remote
control and IRT ON or IRT OFF is displayed.
Game source does not work
t The Game Source can not be selected if the MVGP1 Game Module is not
installed. Make sure the MVGP1 Game Module is installed and plugged in.
18
TROUBLESHOOTING
SYMPTOM:
FM Modulator does not work
REMEDY:
t Check if radio is ON and in FM mode.
t Check that radio is tuned to the same frequency as the unit is set to.
t Select another FM channel.
t Reposition the VODEXL10 Wireless FM antenna for better reception.
t Install an FMDIRB (ordered separately).
Remote Control does not work
t Check if the battery is installed correctly.
t Make sure that the remote control battery is fresh.
t The remote control is a dual function remote control, make sure M1/M2 is
selected correctly.
HDMI source does not work with smartphone
t A special adapter is required to connect a smartphone to the HDMI input.
Contact the smartphone service provider for ordering information on the
appropriate adapter.
19
NOTES
20
www.audiovoxproducts.com
2013 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 11788
128-9230a
VODEXL10
10.1" OVERHEAD LED BACKLIT
LCD MONITOR WITH
DVD PLAYER
S
PUSH
OPERATION
MANUAL
TABLE OF CONTENTS
FCC Statement ....................................................................3
Important Notice .............................................................. 4
Warnings ............................................................................ 4
Congratulations ................................................................ 5
Safety Precaution ............................................................. 5
Features ............................................................................. 5
Controls and Indicators Diagram (Front View) ................ 6
Controls and Indicators Diagram (Side Views) ................ 7
VODEXL10 Monitor Mode Settings .................................. 8
Remote Control Operation ............................................... 9
Remote Control Functions ................................................ 9
Turning the Unit On or Off .............................................. 14
Source Feature ................................................................. 15
Picture Control Select...................................................... 17
System Menu Settings and Adjustments ....................... 17
FM Modulator .................................................................. 18
Default DVD ..................................................................... 19
Screen Mode .................................................................... 19
Monitor Mode .................................................................. 20
IR Transmitter................................................................... 20
Language ......................................................................... 21
Factory Setting ................................................................ 21
DVD Setup Menu Setting and Adjustments .................. 22
Using the Setup Menu ..................................................... 22
Language Setup............................................................... 22
DVD Subtitle Setup.......................................................... 23
DVD Audio Setup ............................................................. 23
DVD TV Display ................................................................ 24
DVD TV Type..................................................................... 24
DVD Rating Setup ........................................................... 25
Change Password ............................................................ 25
Load Factory .................................................................... 26
Screen Saver .................................................................... 26
Playing DVDS ................................................................... 27
Playing MP3 Discs ............................................................ 27
DVD Basics ....................................................................... 29
Overhead Dome Lights ................................................... 30
Accessories ....................................................................... 31
Wireless Headphones ...................................................... 31
Game................................................................................. 31
Troubleshooting .............................................................. 32
Replacement Parts........................................................... 34
Specifications ................................................................... 34
Warranty ........................................................................... 35
2
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
-Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
3
Important Notice
Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags.
Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. Routing
wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal
injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.
When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle
ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video
product.
An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle
information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play,
the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle's parking
brake is applied.
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not
applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.
Warnings
•
•
•
•
•
•
Do not use any solvents or cleaning materials when cleaning the video monitor.
Do not use any abrasive cleaners, they may scratch the screen.
Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.
Lock the LCD screen in the fully closed position when not in use.
Before putting on headphones always adjust the volume setting to the lowest position.
Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left on, can drain
the vehicle's battery.
• Do not put pressure on the screen.
• Caution children to avoid touching or scratching the screen, as it may become dirty or damaged.
Licensed under one or more of the following patents,
Patent NOS. 5,775,762 , 5,927,784 and 6,678,892
4
FEATURES
Congratulations
Congratulations on your purchase of the AUDIOVOX VODEXL10 DVD Player
with drop-down video / monitor. The VODEXL10 has been designed to
give you and your family many years of video entertainment in the mobile
environment. Please read the directions that follow to familiarize yourself
with the product to ensure that you obtain the best results from your
equipment.
• 10.1” TFT (Thin Film Transistor) Active Matrix LCD (Liquid Crystal
Display) Monitor
Note: Installation options vary, see the individual owner's manuals for
each component in your system to obtain a full understanding of each
component's operation.
• HDMI / MHL Inputs
• LED Backlighting
• Built-in DVD Player
• Auto-On With Disc Insertion
• OSD (On Screen Display) for Control of Picture Quality and Functions
• Selectable (M1 and M2) IR Receive and Transmit Codes (See page 8)
• Switchable Dual Channel IR Infrared Transmitter (See page 8)
Safety Precaution
• Nine Source Input*
(DVD, USB, HDMI 1, HDMI 2, Media, AV, AUX, DTV, Game)
*Note: The DTV and Game modules are optional equipment and can
be purchased separately.
For safety reasons, when changing video media, it is recommended that
the vehicle is not in motion, and that you do not allow children to unfasten
seat belts to change video media or make any adjustments to the system.
System adjustments can be accomplished using the remote control, while
seat belts remain fastened. Enjoy your AUDIOVOX entertainment system
but remember the safety of all passengers remains the number one
priority.
• Dome Lights with Built-in Three Way Switch
• Built-in 100 Channel Wireless FM Modulator
• Last Position Memory for DVD
• Screen Mode Selection (4:3, 16:9)
• Full Function Remote Control
• Backlit Controls
• AV Output via RCA Jacks
• Plays DVD, CD and MP3 Discs
• Game Port Ready
• Mobile DTV Ready
5
4. HOME/MENU Select Button
This button is used to display and select options on the system menu.
Press and hold for 3 seconds to access the System Menu.
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW)
1
8
9
2 34 5 6 7
S
5. Source/Select (S) Button
Press this button to display the Source OSD screen. Use the cursor
buttons to highlight the desired source. Press the Source/Select button
to access the desired source.
8
PUSH
10
11
6. STOP („) Button
-Press the STOP button once: Stops playback.
-Pressing the PLAY button again will resume normal playback from
where movie was stopped.
-Press the STOP button twice and then press the PLAY button to start
playback from the beginning of the DVD.
12
7. EJECT ( ) Button
This button is used for ejecting a disc from the disc compartment.
8. Dome Lights
Provide additional interior illumination.
13
9. Infrared Transmitter/Remote Sensor
(Location)
1. POWER ( ) Button
This button is used to turn the system on/off.
10. Screen Release
Press this button to release the screen from the locked position.
2. Play/Pause (X/II ) Button
This button is used to start playback of a disc or pause a disc.
11. Ventilation Openings
12. LCD Cut Off Switch
Used to turn off the LCD backlight when the LCD is in the closed
position.
3. UP / DOWN / LEFT / RIGHT (STW X) Cursor Buttons
These cursor buttons are used to navigate menu selections on the
screen.
13. LCD Panel
6
CONTROLS AND INDICATORS DIAGRAM (SIDE VIEWS)
1
2
3 4
5
1. DVD Disc Insertion Slot
For loading and removing discs. When a disc is inserted, the unit will automatically turn ON and switch to DVD source. Insert a disc with label side
facing up.
Note: The disc slot indicator is red when a disc is inserted and green when the disc slot is empty.
2. AUX IN
These jacks are used to supply external audio and video inputs to the unit. (Yellow - Video, White - Left Audio, Red - Right Audio).
3. USB INPUT
For connection of a USB memory device. This input will also charge a USB device that contains a battery.
Note: The USB input supplies up to 1 Amp of charging current. Devices such as tablets may require more than 1 Amp of charging current and it is
recommended to connect the device to a vehicle power outlet for full charging capabilities. When the unit is in DVD/USB mode, 1 Amp charging is
not available.
4. HDMI/MHL 1 INPUT
For connection of devices with HDMI/MHL outputs.
Note: Requires a HDMI/MHL enabled device and a special HDMI/MHl adapter. Contact your HDMI/MHL device supplier for the adapter.
5. THREE POSITION DOME LIGHT SWITCH
ON Turns on the dome lights.
OFF - The dome lights will not turn on in this position.
AUTO - Automatically turns on the dome lights in conjunction with the vehicle's interior illumination.
7
VODEXL10 MONITOR MODE SETTINGS
The VODEXL10 System has an option that allows the user to select from two IR transmit and receive codes (M1 or M2). This feature can be used when using two
VODEXL10 systems in the same installation or if the vehicle has RSA (Rear Seat Audio) that uses an “A” channel headset. The VODEXL10 system comes factory set to
M1. When in the M1 mode, the unit will respond to remote commands when M1 is selected on the remote control and will transmit audio on the A channel. When
in the M2 mode, the unit will respond to remote commands when M2 is selected on the remote control and will transmit audio on the B channel.
Note: Use 2-channel IR headphones set to CH B when the monitor is set to M2 mode.
Selecting a Monitor Code (M1 or M2)
1. Power ON the unit and wait until M1 or M2 appears on the OSD. M1 or M2 will appear on the screen for 4 ~ 5 seconds.
2. Press the System Menu button on the remote control to display the System Menu to change the monitor code from M1 to M2.
PICTURE
WFMM
DEFAULT DVD
ON
SETTING
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
3. Use the W or X cursor buttons to select the Setting sub menu.
4. Use the S or T cursor buttons to select the Monitor Mode sub menu.
5. Use the W or X cursor buttons to select the desired Monitor Mode (M1 or M2).
6. Press OK to confirm the setting. The following screen will appear.
WARNING
SETTING THE MONITOR TO THE M2 MODE WILL
REQUIRE USING 2-CHANNEL HEADPHONES.
USE THE DOWN KEY ON THE REMOTE CONTROL
TO SELECT M2 AND PRESS OK TO SET THE
MONITOR TO M2 MODE
TO REMAIN IN THE M1 MODE PRESS OK
M1
M2
7. Use the S or T cursor buttons to select Monitor Mode (M1 or M2).
8. Press OK to confirm the setting.
9. Press the System Menu button on the remote control to exit the System Menu Mode.
Note: If no action is taken, this menu will disappear in 10 seconds.
8
REMOTE CONTROL FUNCTIONS
REMOTE CONTROL OPERATION
Initial Use
When purchased, the remote control has a battery installed with a Pull Tab
to prevent battery discharge. Remove the Pull Tab before attempting to
use the remote control.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CR2025
15
Battery Replacement
1. Remove the battery holder.
2. Insert one CR2025 battery into the battery holder. Be sure to observe
the correct polarity.
3. Align the battery holder with the remote control and insert. Push it in
until the holder clicks.
9
32
31
30
29
28
27
26
25
16
24
17
18
23
19
20
22
21
* Function control is available on the unit and the Remote Control.
** Function not available in this model.
1. POWER*
Press this button to turn the unit ON and OFF.
2. SOURCE*
Press to display the Source OSD for DVD, USB, HDMI 1, HDMI 2, Media, AV, AUX, DTV and Game.
3. MONITOR SELECT
M1 Button – Set the remote control code to allow control of the unit in M1 mode.
M2 Button – Set the remote control code to allow control of the unit in M2 mode.
4. SCAN BACKWARD ( )
Press to search in a backward direction. Press repeatedly to change the search speed from 2, 4, 8, 16 times and normal speed.
5. SCAN FORWARD ( )
Press to search in a forward direction. Press repeatedly to change the search speed from 2, 4, 8, 16 times and normal speed.
6. TV Mode Select
Switches certain function keys on the remote control for monitor functions.
7. PREVIOUS (
)
Press to return to the previous chapter or track.
8. NEXT (
)
Press to skip to the next chapter or track.
9. PLAY (X)*
Press to activate the play mode while a disc is loaded into the disc compartment.
10
10. SYSTEM MENU
Allows the user to access the system menu. Press the W or X cursor buttons to select PICTURE, WFMM (FM Modulator) and SETTING.
11. CURSOR (STW X)
Use the cursor buttons to access menu selections on the screen.
12. DISPLAY
When in DVD mode, press to display the current disc information while the disc is playing. Use the W or X cursor buttons to select the Title or
Chapter. For Title/Chapter selection use the numeric buttons to enter the desired Title /Chapter selection. When in TV mode, press to display the
monitor status (M1/M2), Source Mode, FMM On/Off, and IRT On/Off.
13. OK
Used to execute a selected setting or menu option.
14. SETUP
Allows the user to access the Setup Menu when the unit is in DVD mode. Use the ST W or X cursor buttons to select options such as language,
video, rating, Misc.
15. REPEAT
Allows the user to repeat a selected title, chapter, or track.
16. A-B REPEAT
Allows user to repeat the playback from point A to point B.
Press A-B button
On-Screen Display
DVD player
Once
Repeat A
Mark the beginning of the section to repeat (Set point A)
Twice
A-B
Mark the end of the section to repeat (Set point B)
3 times
AB Off
Cancel the A-B repeat function
17. SUBTITLE
Press to display and select the subtitle language in DVD mode. Each time this button is pressed, the subtitle language changes.
Note: The type and number of languages for subtitles vary from disc to disc.
11
18. NUMBERS
Allows the user to enter the numbers 0-9 for selection of the tracks, titles, chapters or password setting.
19. ZOOM
Press this button to enlarge the picture when playing a DVD disc.
Press ZOOM button
DVD player
Once
Q1- Enlarges the picture twice the original size
Twice
Q2- Enlarges the picture 3 times the original size
3 times
Q3- Enlarges the picture 4 times the original size
4 times
Q off- Picture is returned to original size
20. AUDIO
Press to display and select audio language in DVD mode. Each time this button is pressed, the language changes.
Note: The available languages vary from disc to disc.
21. FM MODULATOR CHANNEL SELECT (C)
The unit has a 100 channel built-in wireless FM Modulator. The FM Modulator can be set from 88.1 MHz to 107.9 MHz in 0.2 MHz steps, i.e. 88.1, 88.3,
88.5, 88.9, 90.1 etc. Pressing the C button will display the FM Modulator frequency setting OSD. Use the cursor buttons to select the frequency. Refer
to the SYSTEM MENU SETTINGS AND ADJUSTMENTS for more details.
22. FMM ON/OFF
Turns the FM Modulator power on/off.
23. IRT ON/OFF
Turns the Infrared Transmitter on/off for IR wireless headphones.
12
24. PIX ( Picture Select )**
No function on this model.
25. VOLUME DOWN (-) or UP (+)**
No function on this model.
26. MUTE
Press this button to mute the audio for the wireless FM Modulator, IR headphones and audio output.
Pressing the button again restores the audio to the previously set level.
27. DISC MENU
Allows the user to access the disc’s menu mode.
28. STOP („)*
Press to stop playback. (Playback will resume from the point it is stopped).
Press twice to stop playback fully. (Playback will resume from the beginning of the disc).
29. PAUSE (II)*
Press to pause playback.
30. DVD Source**
No function on this model.
31. DVD Mode Select Button
Switches certain function keys on the remote control for DVD function.
32. EJECT ( )*
Press this button to eject the disc.
13
TURNING THE UNIT ON OR OFF
1. Push in the Screen Release button to unlock the LCD screen. The screen will drop down slightly.
2. Pivot the screen downward until a comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use.
3.
Press the power button on the unit or the remote control to turn the system on and off. When in use, the internal backlighting will illuminate the
controls.
4. After the unit has been turned on and is displaying a picture, adjust the viewing angle by pivoting the screen to optimize the picture quality.
5. Remember to turn the unit off and pivot the LCD screen to the locked position when not in use.
Power
ON/OFF
Button
S
Screen Release
PUSH
14
SOURCE FEATURE
The VODEXL10 System is capable of accessing nine source inputs. To select or change a source, press the source, S, button on the front panel or the SRC
button on the remote control. The source OSD will appear on the screen as shown in the figure below. Use the S T W or X cursor buttons on the front
panel or the S T W or X cursor buttons on the remote control to highlight a source. Press the Source, S, button on the front panel or the OK button on
the remote control to select the desired source.
Note: If a source is grayed out, that source is not available or not installed such as DTV or Game.
DVD
The DVD source input is used to play DVDs, Audio CDs and MP3 discs.
USB
The USB source input is used to play MP3 files, JPEG files (Photos) and AVI (Audio Video Interleaved) files.
Note: Some AVI files may not be compatible with the system, maximum video resolution is 720 x 480.
HDMI 1 & HDMI 2
The HDMI inputs allow the user to enjoy high-definition digital images and high-quality sound by connecting a HD device such as a Blu-ray player or
smartphone with an HDMI output to the system. The HDMI inputs also allow the user to connect with a Mobile High-Definition Link (MHL) mobile phone.
Plug in the HDMI/MHL device with a special adapter available from your mobile phone provider.
Notes:
• This source requires an HDMI/MHL enabled device and a special HDMI/MHL adapter. Contact your HDMI/MHL device supplier for the adapter.
• Phone functionality (phone calls, texting, etc.) may be limited while using the adapter.
• HDMI content is copy protected and is not available on the AV output of the VODEXL10 System.
APPLICABLE HDMI FEATURE
- Input audio signal: 2 channel.
- Input video signal: 480p, 576p, 720p, 1080i, and 1080p.
Note: MHL is only available on HDMI1.
15
MEDIA
The Media source allows for the user to connect an Apple device (e.g. iPod, iPhone, iPad) to the VODEXL10 System to play audio and video content. A
special Apple adapter is required for this connection. See your Apple or electronics dealer for the specific adapter required. Connect the adapter to the
Apple device, and connect the Audio, Video, and USB connectors into the VODEXL10 System. With the Media source selected, the desired video and
audio content can be displayed on the VODEXL10 System.
Notes:
• The USB input supplies up to 1 Amp of charging current. Devices such as tablets may require more than 1 Amp of charging current and it is
recommended to connect the device to a vehicle power outlet for full charging capabilities.
• The Apple device will not display the desired audio and video content on the Apple device screen. The desired audio and video content will only be
displayed on the VODEXL10 System.
AV
An external video source, video game system, or other audio/video devices can be connected to the AV input. This AV input connection is normally
performed when the unit is installed. Turn the video source component on with its power button or remote control and it is now ready to play the audio
and video signals from the source connected to the AV input.
Note: If a DTV module is installed, this input will not be available and the AV source will be grayed out.
AUX
An external video source, video game system or other audio/video devices may be connected to the system via the AUX input. Plug the RCA plugs from
the external source into the RCA jacks on the side of the unit. Turn the external source component on with its power button or remote control and it is
now ready to play the audio and video signal from the source connected to AUX.
DTV
The optional DTV (Digital TV) input is used for a digital TV module. If the digital TV module is not installed, the DTV Source will be grayed out on the
source selection screen and cannot be selected. Check with your installer for availability.
GAME
The optional MVGP1 Wireless Game Package consists of 2 game controllers and a game module containing 54 games, 6 of which are two player games.
If the MVGP1 Wireless Game Package is not installed, the Game Source will be grayed out on the source selection screen and cannot be selected. Check
with your installer for availability.
16
PICTURE CONTROL SELECT
When watching a program, the picture quality can be adjusted to the user’s preferences.
1. Press the System Menu button on the remote control (or press and hold the Home/System menu button on the front panel for 3 seconds) and the
Picture Control Menu will be displayed. The menu contains the on screen picture “adjustment bar” for BRIGHTNESS, CONTRAST, COLOR, TINT (for
NTSC only) or RESET.
PICTURE
WFMM
SETTING
BRIGHTNESS
CONTRAST
COLOR
TINT
RESET
EXIT
2. Use the S T W or X cursor buttons on the remote control or the front panel to adjust the selected adjustment bar for picture quality.
Note: The System Menu will time out after 5 seconds if no buttons are pressed.
SYSTEM MENU SETTINGS AND ADJUSTMENTS
The System Menu contains features and options that let the user customize the system. For example, the user can change the Picture, FM Modulator, OSD
language, source default, screen mode display, and the monitor mode.
Using the System Menu
1. Press the SYSTEM MENU button on the remote control. The system menu main page will appear on the screen.
2. Use the S T W or X cursor buttons to select an item in the sub menu, then press OK to select.
3. Press the System Menu button to exit the System Menu.
Note: The System Menu can be controlled via Remote Control or the Home button on the front panel of the unit (Items selected in the menu will have a
yellow background).
17
FM MODULATOR
The FM Modulator allows the user to listen to audio through the vehicle’s radio.
ON
- Turns the wireless FM Modulator on if audio playback through your vehicle’s radio is preferred.
OFF
- Turns the wireless FM Modulator off.
FREQUENCY - Allows the user to select the wireless FM Modulator frequency. The unit has a 100 channel built-in wireless FM Modulator. The FM
Modulator can be set from 88.1 MHz to 107.9 MHz in 0.2 MHz steps, i.e. 88.1, 88.3, 88.5, 88.9, 90.1 etc.
PICTURE
WFMM
ON
SETTING
OFF
FREQUENCY
88.10
88.90
89.70
90.50
91.30
88.50
89.30
90.10
90.90
91.70
88.30
89.10
89.90
90.70
91.50
88.70
89.50
90.30
91.10
91.90
EXIT
To choose an FM frequency for audio playback through your vehicle’s radio:
1. Press the SYSTEM MENU button to access the System Menu. The System Menu screens appears.
2. Use the X cursor button to highlight wireless FM modulator (WFMM).
3. Use the T cursor button to highlight the FREQUENCY Submenu.
4. Use the S T W or X cursor buttons to select a frequency not used by a radio station in the area. Press OK to select the highlighted frequency.
There are a total of 5 FM CHANNEL pages containing frequencies from 88.1 MHz to 107.9 MHz in 0.2 MHz steps. To access the additional FM Channel
pages, use the W or X cursor buttons to highlight the on screen left and right arrows and press OK. Once the frequency has been selected, tune the
vehicle’s radio to the selected frequency.
5. Press the DVD button to restore the remote control to DVD functions.
Note: The wireless FM modulator will perform well in most applications. However, in certain geographical areas the quality of the wireless signal may be
less than optimal, resulting in static or strong local station bleed through. If this is a consistent problem, an FMDIRB (hard wired FM connection) can be
installed by your dealer.
18
DEFAULT DVD
This allows the user to set the system default source to DVD on or off. If source default
is set to ON, every time the unit is turned off then on, the unit will power up
and automatically switch the source to DVD. If source default is set to OFF and
the unit is turned off then on, the unit will power up in the source that was
last selected.
1. Press the System Menu button.
2. Use the X cursor button to highlight SETTING.
3. Use the T cursor buttons to highlight DEFAULT DVD.
4. Use the W or X cursor buttons to select to select ON or OFF.
5. Press OK to confirm the setting.
PICTURE
WFMM
SETTING
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
Note: The unit is set to source default DVD on as the default mode of operation.
Selection of Source default can only be made from within the system menu.
SCREEN MODE
This allows the user to change the screen format (aspect ratio 16:9, 4:3).
To select the screen aspect ratio format:
1. Press the System Menu button.
2. Use the X cursor button to highlight SETTING.
3. Use the T cursor button to highlight SCREEN MODE.
4. Use the W or X cursor buttons to select 16:9, 4:3.
5. Press OK to confirm the setting.
PICTURE
WFMM
SETTING
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
Note: If the screen mode is set to 4:3, the unit it will default to 16:9 when power is
cycled. HDMI 1, 2 and MHL can not be switched to 4:3 screen mode.
19
EXIT
MONITOR MODE
This allows the user to set the system monitor code to M1 or M2.
1. Press the System Menu button on the remote control to change the
monitor code from M1 to M2.
2. Use the W or X cursor buttons to select the Setting sub menu.
3. Use the S or T cursor buttons to select the Monitor Mode sub menu.
4. Use the W or X cursor buttons to select the desired Monitor Mode (M1
or M2).
Note: Setting the unit to the M2 mode will require the use of 2-channel
headphones set to channel 2.
PICTURE
WFMM
SETTING
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
5. Press OK to confirm the setting. The Warning screen will appear.
6. Use the S or T cursor buttons to change the selected Monitor Mode
(M1 or M2).
7. Press OK to confirm the setting.
8. Press the System Menu button on the remote control to exit the System
Menu Mode.
WARNING
SETTING THE MONITOR TO THE M2 MODE WILL
REQUIRE USING 2-CHANNEL HEADPHONES.
USE THE DOWN KEY ON THE REMOTE CONTROL
TO SELECT M2 AND PRESS OK TO SET THE
MONITOR TO M2 MODE
TO REMAIN IN THE M1 MODE PRESS OK
M1
M2
IR TRANSMITTER
This allows the user to turn the IR Transmitter ON or OFF. The IR Transmitter
must be set to ON for the wireless headphones to be operational.
1. Press the System Menu button.
2. Use the X cursor button to highlight SETTING.
3. Use the T cursor button to highlight IR TRANSMITTER.
4. Use the W or X cursor buttons to select ON or OFF.
5. Press OK to confirm the setting.
PICTURE
WFMM
SETTING
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
20
LANGUAGE
This allows the user to return the on-screen display language. The user can
select English, Spanish, French, or German for the on-screen display language.
To select the screen aspect ratio format:
1. Press the System Menu button.
2. Use the X cursor button to highlight SETTING.
3. Use the T cursor button to highlight LANGUAGE.
4. Use the W or X cursor buttons to select the desired language.
5. Press OK to confirm the setting.
PICTURE
WFMM
SETTING
DEFAULT DVD
ON
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
FACTORY SETTING
This allows the user to return the system to the factory default settings.
1. Press the System Menu button.
2. Use the X cursor button to highlight SETTING.
3. Use the T cursor button to highlight FACTORY SETTING.
4. Press OK to confirm the setting.
PICTURE
WFMM
DEFAULT DVD
ON
SETTING
OFF
SCREEN MODE
16:9
4:3
MONITOR MODE
M1
M2
IR TRANSMITTER
ON
OFF
LANGUAGE
FACTORY SETTING
EXIT
21
DVD SETUP MENU SETTINGS AND ADJUSTMENTS
The DVD Setup Menu contains features and options that allow the user customize the DVD player. For example, the user can set a language for the onscreen display or prevent children from viewing DVD playback of adult DVD Titles.
Using the Setup Menu
Press the DVD button and then the SETUP button on the remote control. The Setup Menu appears on the
screen as shown.
1. Use the S or T cursor buttons to highlight the settings to be changed. Use the X cursor button to
highlight the sub-setttings. Use the X cursor button to open the submenu that contains the different
options available. Press OK to set the desired option.
2. Use the W cursor button to position the highlight back on the icon side of the setup page to set the
other options. Repeat steps 1-2.
3. Press the SETUP button again to exit the Setup Menu.
Language
Language
: English
Video
Subtitle
: Off
Rating
Audio
: English
Language
Language
English
Video
Subtitle
Rating
Audio
Misc
LANGUAGE SETUP
DVD Language for On-Screen Display
The Language Menu allows the user to select the language for the on-screen display.
The user can select English, French, Spanish, German or Italian for the OSD language.
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Language menu option
3. Use the X cursor button to select language submenu.
4. Use the X cursor button to select language choices
5. Use the S or T cursor buttons to select the desired language, then press OK to confirm the setting.
6. Press the SETUP button on the remote to exit the Setup Menu.
22
French
Spanish
Misc
German
Italian
DVD SUBTITLE SETUP
The Subtitle Menu allows the user to select the language for the on-screen display subtitles.
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Language menu option.
3. Use the X cursor button to select subtitle submenu.
4. Use the T cursor button to select the subtitle option.
5. Use the X cursor button to select subtitle submenu.
6. Use the S or T cursor buttons to select the desired subtitle language, then press OK to confirm the
setting.
7. Press the SETUP button on the remote to exit the Setup Menu.
Language
Language
Video
Subtitle
Rating
Audio
English
French
Spanish
German
Italian
Misc
Chinese
Japanese
Thai
Off
Note: The subtitle selection is only available for discs that are recorded in the languages listed in the
diagram. If the selected language is not available, the player will play and display on the screen the
original language contained in the disc.
DVD AUDIO SETUP
The Audio Menu allows the user to select the language for audio.
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Language menu option.
3. Use the X cursor button to select audio submenu.
4. Use the T cursor button to select the audio option.
5. Use the X cursor button to select audio submenu.
6. Use the S or T cursor buttons to select the DVD language you desire, then press OK to confirm the
setting.
7. Press the SETUP button on the remote to exit the Setup Menu.
Note: The audio language selection is only available for discs that are recorded in the listed languages.
If the selected language is not available, the player will play and display on the screen the original
language contained in the disc.
23
Language
Language
Video
Subtitle
Rating
Audio
English
French
Spanish
German
Misc
Italian
Chinese
Japanese
Thai
DVD TV DISPLAY
The TV display setup allows the user to set the screen aspect ratio.
4:3 - This displays the wide picture with black bands on the upper and lower portions of the screen.
16:9 - This displays a wide picture with black bands on the upper and lower portion of the screen.
The bandwidth will vary, depending on the aspect ratio of the disc.
1.
2.
3.
4.
5.
Press the SETUP button on the remote to enter the Setup Menu.
Use the S or T cursor buttons to select the Video menu option.
Use the X cursor button to select TV display submenu.
Use the X cursor button to select the desired TV display submenu.
Use the S or T cursor buttons to select the desired aspect ratio, then press OK to confirm the
setting.
6. Press the SETUP button on the remote to exit the Setup Menu.
DVD TV Type
The TV Type setup allows the user to select the television standard which corresponds to your TV.
NTSC - Select this type for NTSC TV.
PAL - Select this type for PAL TV.
MULTI - Select this type for multi-system TV.
1.
2.
3.
4.
5.
6.
Press the SETUP button on the remote to enter the Setup Menu.
Use the S or T cursor buttons to select the Video menu option.
Use the X cursor button to select TV type submenu.
Use the S or T cursor buttons to select the TV type menu option.
Use the X cursor button to select the desired TV type submenu.
Use the S or T cursor buttons to select the desired TV standard, then press OK to confirm the
setting.
7. Press the SETUP button on the remote to exit the Setup Menu.
24
Language
Video
Rating
Misc
TV display
TV type
4:3
16:9
DVD RATING SETUP
Parental
This feature allows the user to limit the content of movie playback from G to Adult. The lower the value, the
more strict the control.
1. G
2. PG
3. PG – 13
4. R
5. NC – 17
6. Adult
The rating level can only be changed when the correct password is provided.
To change the parental control level, perform the following:
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Rating menu option.
3. Use the X cursor button to select parental submenu.
4. Press OK to enter default password (3308) then press OK.
5. Press OK again to select parental submenu.
6. Use the S or T cursor buttons to select the desired rating option, then press OK to confirm the setting.
7. Press the SETUP button on the remote to exit the Setup Menu.
Change Password
To change the password to a unique password:
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Rating menu option.
3. Use the X cursor button to select parental submenu.
4. Use the S or T cursor buttons to select the change password menu option.
5. Press OK to enter default password (3308) then press OK.
6. Press OK again and key in a new 4 digit password, then press OK to confirm the setting.
7. Press the SETUP button on the remote to exit the Setup Menu.
Language
Video
Parental
: 6.Adult
Change Password
Rating
Misc
Language
Video
Parental
: 6.Adult
Change Password
Enter Password
Rating
Misc
Note: The Default Password is 3308. This password is always effective even after the user has selected their own password and changed it. To avoid the
possibility of others using the default password to set the parental level and change the password, record the default password in another area and
delete it from this manual. Some discs can be limited depending on the age of users while some discs cannot.
25
Load Factory
This option allows the user to reset all options to factory settings.
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Misc menu option.
3. Use the X cursor button to select the load factory option, then press OK to enter the submenu.
4. Use the W or X cursor buttons to select the load factory Yes or No, then press OK to confirm the
setting.
5. Press the SETUP button on the remote to exit the Setup Menu.
Language
Video
Load Factory
Screen Saver
: On
Rating
Misc
Language
Load Factory
Load Factory
Video
Note: This function will not affect the Rating control settings.
Screen Saver
Yes
No
Rating
Misc
Screen Saver
This option allows the user to set the Screen Saver mode.
ON - Screen saver will appear
OFF - Screen saver will not appear
1. Press the SETUP button on the remote to enter the Setup Menu.
2. Use the S or T cursor buttons to select the Misc menu option.
3. Use the X cursor button to select the screen saver submenu.
4. Use the T cursor button to select the screen saver option, then press OK to enter the submenu.
5. Use the S or T cursor buttons to select the screen saver on or off, then press OK to confirm the
setting.
6. Press the SETUP button on the remote to exit the Setup Menu.
Note: The DVD player will enter Screen Saver mode if the unit is inactive for approximately 2 minutes.
26
Language
Video
Rating
Misc
Load Factory
Screen Saver
Off
On
PLAYING DVDS
1. Press the DVD button and then the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle,
audio, subtitle, and time.
2. Title Selection
Press the numeric (0~9) buttons to initiate a change of title selection. Then press OK to implement the selection.
3. Chapter Selection
Press the numeric (0~9) buttons to initiate a change of chapter selection. Then press OK to implement the selection.
PLAYING MP3 DISCS
MP3 is a format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little loss of quality, while taking up
much less space. CD-R discs that have been encoded in MP3 format can be played on the DVD player. The DVD player plays the songs in the order they
were burned onto the disc. When playback is started, the elapsed time of the track that is playing will be displayed.
Selecting Folders and Songs
When media MP3 files is loaded in the player, the navigation menu appears automatically.
1. Use the S or T cursor buttons to select the desired folder (if present) on the left side of the menu and press OK. The songs in the folder will be
displayed on screen.
2. Use the S or T cursor buttons to select the desired track containing the song and press OK to begin track playback.
Skipping Songs
Use the Next (
) button on the remote control to move to the next song. Use the Previous (
) button to move to the previous song.
00:00:01
1/12
Selecting a Play Mode
Filter (For MP3 & JPEG only)
The Filter Mode enables or disables the display of files contained on the media based on their file extension.
The filter function applies to the following formats:
Audio - Audio data format (MP3, WMA)
Photo - Photo data format (JPEG)
Video - Video data format (MPEG ,, ,,)
/
Repeat :
off
Video
003
004
005
Music Playing
006
00:00:01
/
001
002
003
Flat Mode
Repeat : Off
Mode
: Normal
004
005
006
27
Audio
Flat Mode Photo
002
1/12
Flat Mode: play the entire disc
This mode is always on (default). During the Flat Mode, all the data folder with MP3, JPEG, and movies will be
played in sequence. If the Flat Mode function is off, it will only play the selected folder; other folders are disabled.
Filter
001
Music Playing
Repeat: play repetitively
The Repeat function has four playing options: Off, Single, Folder, and All. Move the cursor to the Repeat function
and press OK. Each time OK is pressed the unit will cycle through the available options. Off/Single/Folder/All are
displayed in that order. The Repeat default is Off.
Off
Single
Folder
All
00:00:01
/
1/12
Flat Mode
001
Repeat : Off
002
Mode
003
: Normal
004
- Turns the repeat function off.
- Repeats the song being played until STOP is pressed.
- Plays all songs in a folder repetitively.
- Plays all songs on the disc repetitively.
005
Music Playing
006
Mode: play mode
The Mode function has 4 options: Normal, Shuffle, Random and Music Intro. Move cursor to the Mode function
area and press OK repeatedly until the desired mode is displayed.
Normal/Shuffle/Random/Music Intro are displayed in that order. The Mode function default is Normal.
Normal
- Plays all songs in folder once.
Shuffle
- Plays songs in a folder in a shuffle order. Each song in the folder is played only once.
Random
- Plays songs in a folder in a random order. Each song in a folder is only be played once.
Music Intro - Plays each song in order in the folder for 10 seconds.
Remark
- The Music Intro function provides the user with a sample of each song for 10 seconds,thereby
making it easy to select and listen to a favorite song.
Add to program
To add the selected songs into Browser view, make sure disc playback is off. Move the cursor to the Edit mode
function and press OK. After Edit mode is selected, move cursor to songs list and select the songs which will be
compiled. Press OK. A check mark appears to the left of the selected song.
00:00:01
/
1/12
Flat Mode
001
Repeat : Off
002
Mode
003
005
Music Playing
006
00:00:01
/
1/12
001
Edit mode
002
Program view
003
Add to program
004
005
To add the selected songs to the program, move cursor to the “Add to program” function and press OK. The
selected songs are added into a new program list and the check mark will disappear on the playlist. Move the
cursor to the “Program view” function and press OK to browse the songs in the program. Press the PLAY button
to play the selected songs.
Clear program
To clear the selected song files, press the STOP button twice during playback mode. Move the cursor to the Edit
mode function and press OK. After Edit mode is selected, move cursor to selected songs list and select the songs
which you want to delete. Press OK. A check mark will appear to the left of the selected song. Move the cursor to
clear program and press OK. The selected songs will be deleted from the play list.
Music Playing
006
Album:------------
00:00:01
/
1/12
001
Edit mode
002
Broser view
003
Clear program
004
005
006
Album:------------
28
: Normal
004
Music Playing
DVD BASICS
To get the optimum use out of the DVD Player, make sure this section is read completely.
DVD Region Code
The DVD player is preset to a region code at the factory depending on where the DVD player is sold. A DVD from a different region cannot be played in
this unit and the unit will display "WRONG REGION”.
Region 1 - USA, Canada
Region 2 - Japan, Europe, South Africa, Middle East,
Greenland
Region 3 - S. Korea, Taiwan, Hong Kong, Parts of
South East Asia
Region 4 - Australia, New Zealand, Latin America
(including Mexico)
Region 5 - Eastern Europe, Russia, India, Africa
Region 6 - China
29
Types of Discs the DVD System will play
The VODEXL10 DVD system will play the following types of discs:
• DVD* disc - DVD discs which contain MPEG2 video.
• Audio disc - Audio CDs contain musical or sound content only.
• MP3 disc
- A disc that contains audio files (for example, a CD-R with downloaded MP3 files).
• JPEG disc - A disc that contains JPEG files.
*Note: This system is capable of playing most recordable DVD formats. However, due to the variety of disc manufacturers and software, playback cannot
be guaranteed.
Loading and Playing Discs
Before a disc is loaded, make sure that it is compatible with the player. Insert the disc with the label facing the vehicle’s headliner.
Note: The following discs CANNOT be used with this player:
•
•
•
•
•
MiniDiscs
Laserdiscs
CD-1, CD-ROM, DVD-ROM, Super Audio CD (SACD), DVD Audio
Blu-ray Discs
Digital Copy Discs
To load and play a disc:
Insert a disc into the disc slot. The unit will turn on and start playing disc. The disc slot indicator is red when a disc is inserted and green when the disc slot
is empty.
Note: If the unit is set to another source (e.g. HDMI, AV, AUX, Game etc.), inserting a disc in the disc slot will switch the unit to DVD mode and the DVD will
begin to play.
OVERHEAD DOME LIGHTS
The Dome Lights integrated into the unit are controlled by a three position slide switch. Sliding the switch to the ON position will turn the lights ON. The
OFF position will prevent the lights from turning ON with the vehicle's interior lighting. The AUTO position will allow the lights to turn ON and OFF with
the vehicle's interior lighting. Refer to the Installation Guide for wire connections. Do not leave the vehicle unattended with the dome light switch in the
ON position, as this could result in a discharged battery.
30
ACCESSORIES
WIRELESS HEADPHONES
The VODEXL10 includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using the
controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared
transmissions, like visible light, travel only in a straight line.
Note: If the monitor is set to M2 mode, the headphones supplied with this unit will not work, as these headphones are single channel. Only two-channel
wireless headphones will work with this unit when set to M2 mode. The only time it is necessary to set this unit to M2 mode is if there is an RSA (Rear
Seat Audio) installed in the vehicle or if two of these monitors are installed in one vehicle. Press the system menu and highlight monitor mode to change
the M1 mode to M2 mode or M2 mode to M1 mode.
WIRELESS GAME
The optional Wireless Game Package MVGP1 consists of 2 game controllers and a game module containing 54 games, 6 of which are two player games.
BACK
1.
DOWN
SELECT
START
DOWN
A
P1
LED-POWER
INDICATOR
TA
RIGHT
TA
RIGHT
TA
TB
START
B
A
SELECT
LEFT
TB
TB
A
LEFT
DIRECTION
BUTTONS
B
2.
UP
B
UP
3.
4.
5.
P2
6.
SELECT START
7.
8.
One-Player Games
Use the P1 controller to select and play games.
A Key: “A Function Key” activates the jump function
and optional weapons.
B Key: “B Function Key” activates the fire and attack
functions.
TA Key: TURBO “A” Function Key.
TB Key: TURBO “B” Function Key.
BACK Key: The Back key is used to return to the
previous page. While playing a game pressing the
Back button will return to the games list. Pressing the
Back button again will return to the games main page
“54 Arcade Games”.
Press the START button to begin the game. Press the
START button again at any time to pause the game.
Use the SELECT button to exit to the game list.
Direction buttons move the arrow to the desired
game.
Two-Player Games
When there are two players, the first player uses the P1 controller. Player 2 uses the P2 controller. The P1 controller is used for game selection. The P2
controller can select a game, but the game can only be started by pressing the START button on P1 controller.
31
TROUBLESHOOTING
Problem
Solution
IR remote is inoperative.
• Verify that the batteries in the remote are fresh.
• Verify that the remote sensor eye is not obstructed.
• If the monitor is set to M1, press the M1 button on the remote control. If the monitor
is set to M2, press the M2 button on the remote control. (See page 8.)
Disc won't play.
• Insert a disc with the label side facing upwards.
• Check the type of disc you put into disc tray. This DVD only plays DVD, audio CD and MP3. Blu-ray (BD) discs
will not play in this player.
• Both the unit and the disc are coded by region. If the regional codes don’t match, the disc can’t be played.
Play starts, but then stops
immediately.
• The disc is dirty. Clean it.
• The disc is damaged. Try another disc.
• Condensation has formed. Allow player to dry out.
No sound or distorted sound.
• Make sure the DVD is connected properly. Make sure all cables are securely inserted into the appropriate
jacks.
• If the 2-channel IR headphones are being used, turn on the IR headphone power, and make sure the
correct channel (A-B) is selected.
• Make sure the FM Modulator is ON and the proper Frequency has been selected.
• Make sure that unit is set to M1 when using Single Channel Headphones
Can’t advance through a movie.
• You can’t advance through the opening credits and warning information that appears at the beginning of a
movie because the disc is programmed to prohibit that action.
( ) Not allowed at the moment.
The feature or action cannot be completed at this time because:
1. The disc’s software restricts it.
2. The disc’s software doesn’t support the feature (for example, angles).
3. The feature is not available at the moment.
4. The requested title or chapter number is out of the range.
32
Problem
Solution
Picture is distorted.
• The disc might be damaged, try another disc.
• It is normal for some distortion to appear during forward or reverse scan.
No forward or reverse scan.
• Some discs have sections that prohibit rapid scanning or title and chapter skip.
• If you try to skip through the warning information and credits at the beginning of a movie, you won’t be
able to. This part of the movie is often programmed to prohibit skipping through it.
HDMI/MHL input not working for the
HDMI/MHL enabled device.
• May require a special HDMI/MHL adapter. Contact your HDMI/MHL device supplier for the adapter.
Game source does not work
• The Game source can not be selected (grayed out) if the MVGP1 Game Module is not installed. Make sure
the MVGP1 Game Module is installed and plugged in.
DTV source does not work
• The DTV source can not be selected (grayed out) if the DTV Module is not installed. Make sure the DTV is
installed and plugged in.
AV source does not work
• The AV source cannot be selected (grayed out). The DTV module is installed. This input is shared with DTV
input.
33
REPLACEMENT PARTS
SPECIFICATIONS
Remote Control
136-5326
LCD Backlighting
LED
Wireless Headphones
136-5301
Resolution
1024 (RGB) x 600
MVGP1 Game Module
136-5319
Pixels
1,843,200
Game Controller P1
136-5320
Operation Temperature
32 ~131º F (0 ~ 55º C)
Game Controller P2
136-5321
Storage Temperature
-4 ~ 158º F (-20 ~ 70º C)
Back Light Life
20,000 Hours
Video Display System
NTSC / PAL
Video Output
1.0 Vp-p @ 75 ohms
Power Source
12 VDC
Dimensions
LxWxH
10.67" x 12.0" x 2.12 Closed
271mm x 305mm x 54mm Closed
10.67" x 12.0" x 8.97 Open
271mm x 305mm x 228mm Open
Specifications are subject to change without notice.
34
AUDIOVOX LIMITED WARRANTY
Applies to AUDIOVOX Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product (excluding
game controllers) under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original
purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair
labor. A game controller, if supplied, is similarly waranted for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below
This Warranty does not extend to the following: elimination of externally generated static or noise, correction of antenna problems, costs
incurred for installation, removal or reinstallation of the product, or to damage to digital memory, media devices, gaming devices, discs,
speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 48 MONTHS FROM DATE
OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any
liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
128-5148F
Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 1-800-645-4994
35
www.audiovoxproducts.com
© 2013 Audiovox Electronics Corp, 150 Marcus Blvd. Hauppauge, NY 11788
128-9229
Thank you for purchasing an Audiovox product. We pride ourselves on the quality and reliability of all our
electronic products but if you ever need service or have a question, our customer service staff stands ready to
help. Contact us at www.audiovox.com
vPURCHASE REGISTRATION:
Registering on-line will allow us to contact you in the
unlikely event a safety notification is required under the Federal Consumer Safety Act.
L~
AUDIO,'"O~
~ELECTRONICS CORP.
Register Online at:
WWW.AUDIOVOX.COM
Click on Product Registration and Fill Out the Brief Questionnaire