Woodstock SHOP FOX W1730 s Specifications

MODEL W1730
Oscillating Edge Sander
247569
INSTRUCTION MANUAL
(FOR MODELS MANUFACTURED SINCE 10/11)
Phone: 1-360-734-3482 • On-Line Technical Support: tech-support@shopfox.biz
COPYRIGHT © SEPTEMBER, 2004 BY WOODSTOCK INTERNATIONAL, INC., REVISED NOVEMBER, 2011 (TS)
#6571CA
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents................................. 1
SAFETY................................................4
Standard Machinery Safety Instructions....... 4
Additional Safety for Oscillating Edge Sanders
6
Avoiding Potential Injuries....................... 7
SAFETY
INTRODUCTION......................................2
Woodstock Technical Support................... 2
About Your New W1730 Oscillating Edge
Sander............................................... 2
Specifications...................................... 2
Controls and Features............................ 3
MAINTENANCE..................................... 22
General........................................... 22
Cleaning.......................................... 22
Table & Base..................................... 22
Lubrication....................................... 23
Spindle Connector............................... 24
Eccentric......................................... 24
Calibrating Angle Gauge....................... 26
Removing Drive Roller.......................... 27
W1730 Wiring Diagram......................... 28
Troubleshooting.................................. 29
INTRODUCTION
Table of Contents
WARRANTY......................................... 37
MAINTENANCE
SERVICE
PARTS
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
OPERATIONS
SET UP............................................... 10
Unpacking........................................ 10
Items Needed for Set Up....................... 10
Inventory......................................... 11
Machine Placement............................. 12
Cleaning Machine................................ 12
Sanding Belt...................................... 13
Backstop.......................................... 13
Dust Port.......................................... 14
Dust Port Door................................... 14
Dust Port Cover.................................. 14
Sanding Spindle.................................. 15
Dust Collection.................................. 16
Gear Box.......................................... 16
Test Run........................................... 16
Belt Tracking..................................... 17
Emergency Stop Button........................ 18
Platen Angle Adjustment....................... 19
Table Adjustment............................... 19
Miter Gauge...................................... 20
Fence.............................................. 20
Spindle Table Height............................ 20
Spindle Sanding.................................. 21
End & Edge Sanding............................. 21
SETUP
ELECTRICAL..........................................8
Circuit Requirements............................. 8
Grounding Requirements......................... 9
Extension Cords................................... 9
INTRODUCTION
W1730 Oscillating Edge Sander
INTRODUCTION
Woodstock Technical Support
We stand behind our machines! In the event that questions arise about your machine, parts are missing, or a defect is found, please contact Woodstock International Technical Support at 1-360-734-3482 or
send e-mail to: tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot problems, send out parts or arrange warranty returns.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock International, Inc.
Attn: Technical Support Department
P.O. Box 2309
Bellingham, WA 98227
About Your New W1730 Oscillating Edge Sander
Your new SHOP FOX® W1730 Oscillating Edge Sander has been specially designed to provide many years
of trouble-free service. Close attention to detail, ruggedly built parts, and a discerning quality control
program assure safe and reliable operation.
This W1730 Oscillating Edge Sander has a vertically and horizontally adjustable table and a 0˚-90˚ tilting platen, for a full range of adjustment for custom applications. The Model W1730 has a 2 HP motor,
and vertically oscillates the 6" x 89" belt three-quarters of an inch fifty-two times per minute. The cast
iron auxiliary table provides space for edge sanding as well as spindle sanding with the spindle sanding
attachment. Complementing features to best utilize the adjustment range of the Model W1730 are a Tslot cast iron table, a 180˚ adjustable miter gauge, and a powder coated removable fence.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and durability of this product be included.
Specifications
Motor................................................................. 2 HP, 9A, 240V, Single-Phase
Main Table.................................................................. 26-7/8" x 12", Cast Iron
Auxiliary Table..........................................................................10" x 11-1/2"
Belt Size....................................................................................... 6" x 89"
Belt Speed.................................................................................. 3150 FPM
Belt Oscillation Stroke...........................................................................3/4"
Belt Oscillation Cycle............................................................. 52 Cycles/Minute
Platen......................................................................... Steel w/Graphite Pad
Platen Tilt...................................................................................... 0˚­­—90˚
Spindle Drums (3).......................................................................1-1/2", 2", 3"
Dust Port Size....................................................................................... 4"
Approximate Machine Weight.............................................................. 396 lbs.
-2-
INTRODUCTION
W1730 Oscillating Edge Sander
Controls and Features
2
3
4
1
5
6
16
7
15
8
14
9
13
10
12
11
Figure 1. Controls and Features of the W1730.
1. Sanding Spindle Table
2. Sanding Spindle
3. Belt Access Door
4. Emergency Stop Switch
5. Back Stop
6. Dust Port
7.Motor
8. Angle Adjustment & Lock Handle
9. Belt Tracking Adjustment
10.Vertical Adjustment Lock Handles
11. Vertical Adjustment Handwheel
12.Storage Compartment
13. Sanding Table
14.ON/OFF Switch
15.Table Lock Levers
16.Spindle Table Adjustment Lock Handle
For Your Own Safety Read Instruction Manual Before Operating Saw
a) Wear eye protection.
b) Support workpiece with miter gauge, backstop or worktable.
c)Maintain 1⁄16" in maximum clearance between table and sanding belt.
d) Avoid kickback by sanding in accordance with the directional arrows.
-3-
W1730 Oscillating Edge Sander
SAFETY
SAFETY
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention measures—this responsibility is ultimately up to the operator!
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
NOTICE
This symbol is used to alert the user to useful information about
proper operation of the equipment, and/or a situation that may
cause damage to the machinery.
Standard Machinery Safety Instructions
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.
HEARING PROTECTION. Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
MENTAL ALERTNESS. Be mentally alert when
running machinery. Never operate under the
influence of drugs or alcohol, when tired, or
when distracted.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware
of dust hazards associated with workpiece
materials, and always wear a NIOSH-approved
respirator to reduce your risk.
DISCONNECTING POWER SUPPLY. Always
disconnect machine from power supply before
servicing, adjusting, or changing cutting tools
(bits, blades, cutters, etc.). Make sure switch
is in OFF position before reconnecting to avoid
an unexpected or unintentional start.
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips which could cause a loss
of workpiece control.
DANGEROUS ENVIRONMENTS. Do not use
machinery in wet or rainy locations, cluttered
areas, around flammables, or in poorly-lit
areas. Keep work area clean, dry, and welllighted to minimize risk of injury.
-4-
W1730 Oscillating Edge Sander
STABLE MACHINE. Unexpected movement during
operations greatly increases the risk of injury
and loss of control. Verify machines are
stable/secure and mobile bases (if used) are
locked before starting.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
ONLY USE AS INTENDED. Only use machine for
its intended purpose. Never modify or alter
machine for a purpose not intended by the
manufacturer or serious injury may result!
AWKWARD POSITIONS. Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase the risk of serious
injury.
UNATTENDED OPERATION. Never leave machine
running while unattended. Turn machine off
and ensure all moving parts completely stop
before walking away.
CHILDREN & BYSTANDERS. Keep children and
bystanders a safe distance away from work
area. Stop using machine if children or
bystanders become a distraction.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. An
improperly maintained machine may increase
the risk of serious injury.
REMOVE ADJUSTING TOOLS. Never leave
adjustment tools, chuck keys, wrenches, etc.
in or on machine—especially near moving
parts. Verify removal before starting!
CHECK DAMAGED PARTS. Regularly inspect
machine for damaged parts, loose bolts,
mis-adjusted or mis-aligned parts, binding,
or any other conditions that may affect safe
operation. Always repair or replace damaged
parts, wires, cords, or plugs before operating
machine.
SECURING WORKPIECE. When required, use
clamps or vises to secure workpiece. A secured
workpiece protects hands and frees both of
them to operate the machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside. Do not
handle the cord/plug with wet hands. Avoid
cord damage by keeping it away from heated
surfaces, high traffic areas, harsh chemicals,
and wet or damp locations.
FEED DIRECTION. Unless otherwise noted, feed
work against the rotation of blades or cutters.
Feeding in the same direction of rotation may
pull your hand into the cut.
GUARDS & COVERS. Guards and covers can
protect you from accidental contact with
moving parts or flying debris. Make sure
they are properly installed, undamaged, and
working correctly before using machine.
EXPERIENCING DIFFICULTIES. If at any time you
are experiencing difficulties performing the
intended operation, stop using the machine!
Contact our Technical Support for help at
(360) 734-3482.
NEVER STAND ON MACHINE. Serious injury or
accidental contact with cutting tool may
occur if machine is tipped. Machine may be
damaged.
-5-
SAFETY
APPROVED OPERATION. Untrained operators
can be seriously hurt by machinery. Only
allow trained or properly supervised people
to use machine. When machine is not being
used, disconnect power, remove switch keys,
or lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
W1730 Oscillating Edge Sander
Additional Safety for Oscillating Edge Sanders
SAFETY
READ MANUAL. This manual contains proper operating and safety procedures for this machine.
WORKPIECE PRESSURE. Do not jam the workpiece against the sanding surfaces. Firmly grasp the
workpiece in both hands and ease it against the belt/spindle using light pressure.
CLOTHING. Do not wear loose clothing or jewelry while operating this machine. Roll up or button sleeves
at the cuff, and tie back long hair.
HAND PLACEMENT. Do not place hands near, or in contact with, sanding surfaces during operation.
WORKPIECE HANDLING. Grip the workpiece with both hands, or the workpiece may be thrown from
machine and cause serious personal injury.
MAINTENANCE. Perform machine inspections and maintenance promptly as required.
UNATTENDED MACHINE. Never leave the machine running unattended.
SANDING BELTS/DRUMS. Replace sanding belts and drums promptly as needed.
WORKPIECE QUANTITY. Never sand more than one piece of stock at a time.
FOREIGN MATERIAL. Always inspect stock for nails, staples, knots, and other imperfections that could
be dislodged and thrown from the machine during sanding operations.
DUST COLLECTION. Never operate the sander without an adequate dust collection system in place and
running.
DIRECTION. Never sand tapered or pointed stock with the point facing the feed direction, or the
workpiece may be thrown from machine and cause serious personal injury.
POWER DISCONNECT. Disconnect the machine from the power source before changing the sanding belt
or sleeve.
TEST RUN. Test run the machine before starting any work.
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury
may occur if safety and
operational information is
not understood and followed. DO NOT risk your
safety by not reading!
Use this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
-6-
W1730 Oscillating Edge Sander
Avoiding Potential Injuries
SAFETY
Figure 2. DO NOT leave a gap between wood
and back stop, and keep hands away from belt.
Figure 5. ALWAYS use the back stop, and keep
fingers away from the belt.
Figure 3. DO NOT sand wood with fingers close
to spindle.
Figure 6. ALWAYS keep your fingers away from
the spindle.
Figure 4. DO NOT sand wood with sharp corners
at the leading-edge of the sanding operation.
The belt can grab and throw the wood.
Figure 7. ALWAYS sand wood with sharp corners
at the trailing-edge of the sanding operation.
-7-
W1730 Oscillating Edge Sander
ELECTRICAL
Circuit Requirements
SETUP
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do later in
this manual.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the fullload current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Full-Load Current Rating at 240V.....................9 Amps
Circuit Requirements for 240V
This machine is prewired to operate on a 220V power
supply circuit that has a verified ground and meets the
following requirements:
Circuit Type................220V/240V, 60 Hz, Single-Phase
Circuit Size.............................................. 15 Amps
Plug/Receptacle..................................... NEMA 6-15
-8-
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
or machine damage. To reduce this risk,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to a dedicated circuit—
where only one machine will be running
at a time. If this machine will be
connected to a shared circuit where
multiple machines will be running at
the same time, consult a qualified
electrician to ensure that the circuit is
properly sized for safe operation.
W1730 Oscillating Edge Sander
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of malfunctions or breakdowns, grounding provides
a path of least resistance for electric current to travel—in
order to reduce the risk of electric shock.
Improper connection of the equipment-grounding wire will
increase the risk of electric shock. The wire with green
insulation (with/without yellow stripes) is the equipmentgrounding wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipmentgrounding wire to a live (current carrying) terminal.
220V
GROUNDED
6-15 RECEPTACLE
Current Carrying Prongs
6-15 PLUG
Grounding Prong
Figure 8. NEMA 6-15 plug & receptacle.
For 240V Connection
The power cord and plug specified under "Circuit
Requirements for 240V" on the previous page has an
equipment-grounding wire and a grounding prong. The
plug must only inserted into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances (see
Figure 8).
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required plug and receptacle, and
meet the following requirements:
Minimum Gauge Size at 240V....................... 14 AWG
Maximum Length (Shorter is Better).................50 ft.
-9-
DO NOT modify the provided plug or use
an adapter if the plug will not fit your
receptacle. Instead, have a qualified
electrician install the proper receptacle
on a power supply circuit that meets the
requirements for this machine.
SETUP
Check with a qualified electrician or service personnel
if you do not understand these grounding requirements,
or if you are in doubt about whether the tool is
properly grounded. If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instructed to do later in
this manual.
W1730 Oscillating Edge Sander
SET UP
Unpacking
The SHOP FOX® Model W1730 has been carefully packaged for safe transporting. If you notice the machine has
been damaged, please contact Woodstock International
Technical Support at 1-360-734-3482 or send e-mail to:
tech-support@shopfox.biz
SETUP
Items Needed for Set Up
The following items are needed, but not included, to
setup your machine:
Description
• Phillips Screwdriver........................................1
• Straight Slot Screwdriver..................................1
• Machinist's Square..........................................1
•Hammer......................................................1
• Socket 7/8"..................................................1
• Ratchet w/6" extension...................................1
• Hex Wrench 4mm...........................................1
• Dust Collector...............................................1
• Dust Hoses 4"................................................2
• Hose Clamps 4".............................................4
READ and understand this entire instruction manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
Seek assistance when lifting the
machine from the shipping box . The
Model W1730 weighs 396 lbs.
UNPLUG the power cord before you
do any assembly or adjustment tasks!
Otherwise, serious personal injury to
you or others may occur!
-10-
W1730 Oscillating Edge Sander
Inventory
The following is a description of the main components
shipped with the SHOP FOX® Model W1730. Lay the components out to inventory them.
Box Contents (Figure 9):
A.Fence.........................................................1
B. Spindle Table Assembly....................................1
C. Sanding Belt.................................................1
D. Miter Gauge.................................................1
E. Dust Port.....................................................1
F. Back Stop....................................................1
G. Dust Port Cover.............................................1
H. Dust Port Door..............................................1
If any parts appear to be missing, examine the packaging
carefully. If any parts are missing, find the part number
in the back of this manual and contact Woodstock
International, Inc. at 360-734-3482 or at tech-support@
shopfox.biz
-11-
B
C
H
E
D
F
A
SETUP
Box Contents Continued (Figure 10):
I. 3" Drum......................................................1
J. 2" Drum......................................................1
K. 1-1/2" Drum.................................................1
L. 3" Table Insert...............................................1
M. 2" Table Insert...............................................1
N. 1-1/2" Table Insert.........................................1
O.Spindle.......................................................1
P. Hardware Bag...............................................1
­• Lock Handle...............................................1
• Star Knob 5/16-18 x 1...................................2
• Hex Bolt 5/16-18 x 1....................................2
• Hex Bolt 5/16-18 x 1/2.................................1
• Phillips Head Screw 1/4-20 x 3/8".....................4
• Spindle Washer 5/16.....................................1
• Flat Washer 5/16.........................................4
• Hinge Pin..................................................4
• Open End Wrench 10mm x 12mm.....................1
• Hex Wrench 5mm........................................1
• Hex Wrench 6mm........................................1
• Rod.........................................................1
• Drive Puller Plate........................................1
• Cap Screw 5/16-18 x 1-1/4 ............................1
• Cap Screw 1/4-20 x 1-3/4..............................2
G
Figure 9. Box contents.
J
I
K
N
O
P
M
L
Figure 10. Box contents continued.
NOTICE
When ordering replacement parts, refer
to the parts list and diagram in the back
of the manual.
SUFFOCATION HAZARD!
Immediately discard all
plastic bags and packing materials to eliminate choking/suffocation
hazards for children and
animals.
W1730 Oscillating Edge Sander
SETUP
Machine Placement
•
Floor Load: Your Model W1730 Oscillating
Edge Sander weighs 396 lbs with a 22-1/2"
x 19-1/2" footprint. Some residential floors
may require additional bracing to support
both machine and operator.
•
Working Clearances: Consider all existing
and anticipated needs, size of material to
be processed through the machine, and
space for auxiliary stands, work tables,
or other machinery when establishing a
location for your Model W1730 Oscillating
Edge Sander.
•
Cleaning Machine
The table and other unpainted parts of your
Model W1730 Oscillating Edge Sander are coated
with a waxy grease that protects them from
corrosion during shipment. Clean this grease off
with a solvent cleaner or citrus-based degreaser.
DO NOT use chlorine-based solvents such as
brake parts cleaner or acetone—if you happen
to splash some onto a painted surface, you will
ruin the finish.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
Most have low flash
points, which make them
extremely
flammable.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
Electrical: Electrical circuits should be
dedicated or able to handle amperage
requirements. Outlets should be located
near each machine, so power cords are
clear of high-traffic areas. Follow local
electrical codes for proper installation of
new lighting, outlets, or circuits.
USE helpers or power lifting equipment to lift this
Model W1730 Oscillating
Edge Sander. Otherwise,
serious personal injury
may occur.
ALWAYS work in wellventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assembling, adjusting or operating equipment.
-12-
W1730 Oscillating Edge Sander
Sanding Belt
To install the belt, do these steps:
1. Open the belt access door by removing the star
knobs and opening all latches.
2. Lift the belt tensioning lever as shown in Figure 11.
3. Determine the belt direction from the arrow on the
dust port and the access door.
4. Match the arrows on the sander to the arrows inside
the sanding belt, and place and center the belt on
the sanding drums as shown in Figure 12.
Figure 11. Released position of the belt
tensioning lever.
6. Close the belt access door, insert the star knobs,
and latch the levers.
7. Adjust the belt tracking as described on Page 17.
Belt Direction
Arrows
Backstop
To mount the back stop, do these steps:
1. Place a 5/16" flat washer on each 5/16-18 x 1 hex
bolt and thread them approximately one turn into
the holes in the platen shown in Figure 13.
2. Slide the back stop onto the hex bolts and tighten,
allowing 1/8" clearance between the belt and the
edge of the back stop.
Figure 12. Placing the sanding belt onto
the sanding drums.
Figure 13. Backstop bolts threaded into
platen.
-13-
SETUP
5. Tension the sanding belt by pushing the belt
tensioning lever down.
W1730 Oscillating Edge Sander
Dust Port
To mount the dust port, do these steps:
1. Align the dust port holes with the tapped holes on
the side of the sander.
2. Insert the 1/4-20 x 3/8 Phillips head screws with
1/4" washers, through the aligned holes and tighten
as shown in Figure 14.
Dust Port Door
SETUP
To mount the dust port door, do these steps:
1. Align the dust port door hinges with the hinges on
the sander.
Figure 14. Dust port installation.
2. Insert the hinge pins through the aligned hinges, as
shown in Figure 15, and tap with a hammer for full
insertion.
3. Close and latch the dust port door.
Dust Port Cover
To mount the dust port cover, do these steps:
1. Align the dust port cover hinges with the hinges on
the sander.
2. Insert the hinge pins through the aligned hinges
(Figure 16), and tap with a hammer.
Figure 15. Dust port door.
3. Shut and latch the dust port cover.
Figure 16. Inserting dust port cover hinge
pin.
-14-
W1730 Oscillating Edge Sander
Sanding Spindle
The Model W1730 comes with a spindle sanding
attachment for sanding curved surfaces. The included
sanding drums measure 1-1/2", 2", and 3" in diameter. The
spindle table may also be used on the end of the sanding
belt if so desired. Be sure to periodically adjust the table
height to minimize spot wear on the spindle/belt.
To install the sanding spindle, do these steps:
1. Release the dust port cover latch, open the cover,
then latch the cover to the belt access door.
3. Line up the screw holes and place the spindle into
the sanding belt drum.
Figure 17. Securing the cap screws.
4. Thread the cap screws removed in Step 2 into the
sanding belt drum and tighten evenly and securely
as shown in Figure 17.
5. Slide a sanding drum onto the spindle, and insert
the 5/16" spindle washer and 5/16-18 x 1/2 hex bolt
into the top of the spindle.
6. Insert the rod into the side of the spindle to anchor
it and tighten the hex bolt as shown in Figure 18.
7. Insert the spindle table assembly shaft into the
opening in the idler roller bracket as shown in
Figure 19.
Figure 18. Anchoring the spindle with the
rod.
8. Thread the table lock handle into the pre-tapped
hole in the idler roller bracket. Note­: The handle is
spring loaded and can be used as a ratchet.
9. Remove the installed table insert by removing the
three flat head screws in the insert.
10.Replace with the table insert that matches the
sanding drum diameter. Tighten with the flat head
screws removed in Step 9.
Figure 19. Inserting spindle table
assembly into idler roller bracket.
-15-
SETUP
2. Remove the three cap screws and false cover from
the sanding belt drum.
W1730 Oscillating Edge Sander
Dust Collection
There are two 4" dust collection ports that should be
connected to a dust collector. The port locations are
shown in Figure 20.
To connect your machine to a dust collection system,
do these steps:
1. Use a 4" diameter hose and clamps to connect a dust
collection system to your dust ports.
SETUP
2. Check for a snug fit by gently tugging on the hose.
Gear Box
It is vital for the gear box to be correctly filled with SAE
80W oil before any operation. The gear box is filled at
the factory, but the oil level should be double checked.
To check and refill the gear box, do these steps:
Figure 20. W1730 dust ports.
1. Place the belt sander in the horizontal position.
2. Locate the gear box cover, directly beneath the
motor, and remove the two cap screws and two hex
bolts retaining the gear box cover.
3. Remove the oil fill plug on top of the gear box
(Figure 21) and check the oil level.
—If the oil is within 1/2" from the top, the oil level is correct, continue to step 4.
—If the oil level is not within 1/2" from the top, fill
the gear box with SAE 80W gear oil until the level
is 1/2" from the top.
4. Reinstall the cover, hex bolts and cap screws.
Test Run
Once all Set Up procedures up to this point have been
completed, it is time to test run your new sander.
Turn the machine ON and keep the your hand poised near
the switch just in case there is a problem. The machine
should run smoothly with little or no vibration or rubbing
noises. Turn the machine OFF. Strange or unnatural noises
should be investigated and corrected before further
operation of the machine.
If you cannot easily locate the source of unusual noise or
vibration, contact Woodstock International, Inc. at 360734-3482 or at tech-support@shopfox.biz
-16-
Figure 21. Checking gear box oil level.
W1730 Oscillating Edge Sander
Belt Tracking
After the sanding belt has been removed or replaced,
or used for a significant amount of time, it may be
necessary to adjust the sanding belt tracking.
To adjust the sanding belt tracking, do these steps:
Jam Nut
CW
CCW
1. Turn the machine ON long enough to observe the
tracking of the sanding belt, then turn it OFF.
2. If the sanding belt does not track on a centered
path across the rollers, adjustment is necessary.
4. Loosen the jam nut shown in Figure 22.
5. Determine if the sanding belt is tracking too high, or
too low:
• If the belt tracks above center, turn the
adjustment nut, shown in Figure 22,
counterclockwise.
• If the sanding belt tracks below center, turn the
adjustment nut clockwise.
Figure 22. Jam and adjustment nuts,
clockwise (CW) and Counter Clockwise
(CCW) rotation.
6. Tighten the jam nut.
7. Connect the machine to power and turn ON.
Observe the belt tracking behavior for at least two
minutes:
­• If the belt is tracking correctly, no further
adjustment is necessary.
­• If the belt is not tracking correctly, repeat Steps
3-7.
-17-
DO NOT attempt to perform any
adjustments to the sanding belt while
the machine is connected to a power
source. Failure to unplug before
adjusting the sanding belt could result
in serious personal injury.
SETUP
3. Unplug the sander!
Adjustment
Nut
W1730 Oscillating Edge Sander
OPERATIONS
General
Your Model W1730 will allow you to perform many types
of sanding operations. However, the following section is
not a complete guide to the many specialized applications
of the Model W1730 Oscillating Edge Sander; nor does
it include the various aftermarket products that can be
used with this W1730 Oscillating Edge Sander.
OPERATIONS
We strongly recommend that you read books, trade
articles or seek training with W1730 Oscillating Edge
Sanders before performing any operations in which you
are not confident. Above all, your safety should come
first. This recommended research will pay off with your
increased safety, the quality of your work and the gain in
knowledge you will make as a woodworker.
Always wear safety glasses when operating the Model W1730 Oscillating
Edge Sander. Failure to comply may
result in serious personal injury.
Belt Grits
There are many types of sanding belts to choose from.
We recommend aluminum oxide for general workshop
environments. Below is a chart that groups abrasives
into different classes and shows which grits fall into each
class.
Grit
Type
24-36
Very Coarse
40-60
Coarse
80-100
Medium
120-180
Fine
220-360
Very Fine
DO NOT investigate problems or adjust
the Model W1730 Oscillating Edge
Sander while it is running. Wait until
the machine is turned off, unplugged
and all working parts have come to a
complete stop before proceeding!
The general rule is to sand a workpiece with progressively
higher grits.
Emergency Stop Button
The Model W1730 is equipped with an emergency stop
button on top of the sander. Should an emergency ever
occur during use of the sander, immediately press the
emergency stop button. See Figure 23 for the emergency
stop button location.
Figure 23. Emergency stop button.
-18-
W1730 Oscillating Edge Sander
Platen Angle Adjustment
The sanding angle of the oscillating edge sander is
variable between 0 and 90 degrees.
To adjust the platen angle, do these steps:
1. Loosen the angle adjustment lock handle and tilt
the sander until the pointer is aligned with the
desired angle as shown in Figure 24.
2. Tighten the angle adjustment lock handle.
Note­: See Page 26 to calibrate the angle scale.
Angle Adjustment
Lock Handle
Table Adjustment
Figure 24. Platen angle scale.
Lock Handle
OPERATIONS
The table on the oscillating edge sander moves both
vertically and horizontally to accommodate various
workpieces shapes and thicknesses. Adjust the table
height periodically to reduce spot wear of your sanding
belt.
To vertically adjust the table, do these steps:
1. Loosen the lock handles (Figure 25) that secure the
table height position.
2. Turn the table height adjustment wheel, shown
in Figure 25, clockwise to raise the table or
counterclockwise to lower the table.
3. When the desired position is achieved, tighten the
lock handles to secure the table height.
Adjustment Wheel
Figure 25. Vertical table adjustment.
To horizontally adjust the table, do these steps:
1. Move the table lock levers to the loose position as
illustrated by the labels on the machine.
2. Push or pull the table until there is a gap of no more
than 1/16" from the sanding belt (Figure 26).
3. Move the table lock levers to the locked position to
secure the table position.
Figure 26. Horizontal table adjustment.
-19-
W1730 Oscillating Edge Sander
Miter Gauge
To adjust the miter gauge, do these steps:
1. Use a machinist's square with one edge against the
face of the miter gauge and the other against the
belt face as shown in Figure 27.
2. Lock the lock knob on the miter gauge and adjust
the miter gauge flush with the edge of the square.
3. Tighten the lock knob, and verify the setting. Note:
Sometimes the tightening procedure can affect the
adjustment.
4. Loosen the screw that secures the angle pointer and
adjust the pointer to the 0˚ mark on the scale.
Figure 27. Squaring the miter gauge.
5. Retighten the screw that secures the angle pointer.
OPERATIONS
Fence
The Model W1730 comes with a removable fence to assist
sanding operations when the platen is horizontal.
To mount the fence, do these steps:
1. Set the fence on the table and align the slots with
the threaded holes in the table.
2. Thread the star knobs and 5/16" flat washers into
the threaded table holes (Figure 28) and tighten.
Figure 28. Installed fence.
Spindle Table Height
The spindle table on the oscillating edge sander can
be moved vertically to accommodate various sanding
operations and to decrease spot wear on the sanding
drums.
To adjust the spindle table height, do these steps:
1. Loosen the adjustment lock handle shown in Figure
29.
2. Raise or lower the table to the desired height.
3. Tighten the adjustment lock handle.
Figure 29. Adjustment lock handle.
-20-
W1730 Oscillating Edge Sander
Spindle Sanding
The spindle sander on the Model W1730 produces a high
quality sanding finish on inside contours. Make sure the
spindle table is properly installed with the correct table
insert for the spindle drum. Move the table on occasion
to reduce spot wear on the sleeves.
To perform spindle sanding operations, do these steps:
1. Make sure that the appropriate spindle and table
insert have been installed correctly and both are
secured tightly.
2. Position the table in the desired location and turn
the power switch ON.
KEEP HANDS CLEAR of all pinch points
when adjusting the spindle table.
3. While securely holding the workpiece, lightly press
it against the spindle and maintain consistent
pressure against the table as shown in Figure 30.
Use extra caution when sanding end-grain.
OPERATIONS
4. When you have completed your sanding operation,
turn the power switch OFF.
End & Edge Sanding
Proper use of the oscillating edge sander will yield
excellent sanding results due to the oscillating movement.
To perform an edge or end sanding operation, do these
steps:
Figure 30. A typical spindle sanding
operation.
1. Start the sander by turning the switch ON.
2. Support the workpiece against the back stop, and
slowly feed the workpiece into the moving belt,
as shown in Figure 31. Note: If you must feed a
workpiece into the sanding belt corner first, feed
the trailing corner first. Feeding the leading corner
first could cause the sanding belt to grab the
workpiece and jerk it out of your hands.
3. When you have completed your sanding operation,
turn the power switch OFF.
Figure 31. Edge sanding with the Model
W1730.
-21-
W1730 Oscillating Edge Sander
MAINTENANCE
General
Regular periodic maintenance on your SHOP FOX® Model
W1730 will ensure its optimum performance. Make a habit
of inspecting your oscillating edge sander each time you
use it.
Check for the following conditions and repair or
replace when necessary:
•
•
•
•
•
•
Loose mounting bolts.
Worn or damaged sanding belts.
Worn switch.
Worn or damaged cords and plugs.
Damaged V-belt.
Any other condition that could hamper the safe
operation of this machine.
Cleaning
MAINTENANCE
Frequently blow-off sawdust with compressed air. This is
especially important for the internal working parts and
motor. Dust build-up around the motor is a sure way to
decrease its life span.
Occasionally it will become necessary to clean the
internal parts with more than compressed air. To do this,
remove the table top and clean the internal parts with
a citrus cleaner or mineral spirits and a stiff wire brush
or steel wool. Make sure the internal workings are dry
before using the sander again, so that wood dust will not
accumulate. If any essential lubrication is removed during
cleaning, re-lubricate those areas.
Table & Base
Tables can be kept rust-free with regular applications
of a product like SLIPIT®. For long term storage you may
want to consider a product like Boeshield T-9™.
-22-
Make sure that your machine is
unplugged during all maintenance procedures! If this warning is ignored, serious personal injury may occur.
W1730 Oscillating Edge Sander
Lubrication
After operating the Model W1730 for approximately 500
hours, refill the gear box with oil.
To check and refill the gear box, do these steps:
1. Place the platen in the horizontal position.
2. Locate the gear box cover, directly beneath the
motor, and remove the two cap screws and two hex
bolts retaining the gear box cover.
3. Wipe off any dust buildup and remove the oil fill
plug on top of the gear box (Figure 32). Fill the
gear box with SAE 80W gear oil until the level is
1/2" from the top.
4. Reinstall the gear box cover with the hex bolts and
cap screws.
Figure 32. Gear box and oil fill on the
Model W1730.
Rack & Pinion Gear
The rack and pinion gear that moves the table vertically,
located inside the gear cabinet, should be well greased to
maintain smooth operation.
To grease the rack and pinion gear, do these steps:
2. Apply a coat of all purpose grease to the rack and
pinion gears.
Figure 33. Oil ports.
Oil Ports & Grease Fittings
There are two oil ports shown in Figure 33 and four
grease fittings shown in Figure 34 on the Model W1730.
Lubricate these points after approximately 50 hours of
use with a light machine oil.
All other bearings on the Model W1730 are sealed and
permanently lubricated and there is no need to lubricate
them.
Figure 34. Grease fittings.
-23-
MAINTENANCE
1. With the table in its lowest position, wipe the rack
and pinion with a rag to remove the buildup of
sawdust and old grease.
W1730 Oscillating Edge Sander
Spindle Connector
The spindle connector connects the shafts from the
motor to the gear box and is secured by two set screws
that need to be tightened every time the gear box oil is
filled (every 500 hours).
To secure the spindle connector set screws, do these
steps:
1. Refer to Lubrication Steps 1­­­-3 on Page 23 to
remove the gear box cover
2. Tighten the set screws shown in Figure 35.
3. Reinstall the gear box cover.
Figure 35. Spindle connector set screws.
Eccentric
The eccentric on the Model W1730 is connected to the
shaft by a set screw. This set screw needs to be tightened
every time the gear box oil is filled (every 500 hours).
To secure the eccentric set screw, do these steps:
1. Refer to Lubrication, Steps 1­­­-3 on Page 23 to
remove the gear box cover.
MAINTENANCE
2. Tighten the set screw on the eccentric, shown in
Figure 36.
3. Reinstall the gear box cover.
Figure 36. Eccentric set screw.
-24-
W1730 Oscillating Edge Sander
Maintenance Schedule
• Every 2 Hours of Running Time:
Clean and lubricate table top, miter slot and fence.
• Every 3 Hours of Running Time:
Check belt tracking. Check sanding belt condition.
• Every 6-8 Hours of Running Time:
Replace belt.
• Every 2,000 hours:
Replace the rubber V-Belt (recommended). Check the eccentric and spindle connector. Lubricate all oil ports and
grease fittings, rack and pinion gear, and check gear box.
Maintenance Notes
DATE MAINTENANCE PERFORMED
MAINTENANCE
-25-
W1730 Oscillating Edge Sander
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not covered
in this section, please contact Woodstock International
Technical Support for additional guidance at (360) 7343482 or send e-mail to: tech-support@shopfox.biz.
Calibrating Angle Gauge
In order to maintain accuracy and precision with the oscillating edge sander, periodically calibrate the angle gauge.
Make sure that your machine is
unplugged during all service procedures! If this warning is ignored, serious personal injury may occur.
To calibrate the angle gauge, do these steps:
1. Loosen the angle adjustment lock handle.
2. Place the machinist's square on the table and press
it against the platen.
3. Adjust the platen until it is flush with the
machinist's square as in Figure 37.
4. Tighten the angle adjustment lock handle.
5. Loosen the angle indicator pin screw, shown in
Figure 38, a 1/2 turn.
Figure 37. Aligning table to platen.
SERVICE
6. Align the angle indicator pin with the 90˚ mark and
tighten the angle indicator pin screw.
Figure 38. Angle indicator pin screw.
-26-
W1730 Oscillating Edge Sander
Removing Drive Roller
The Model W1730 comes equipped with a puller to
remove the drive roller should it ever become necessary
to do so.
To remove the drive roller, do these steps:
1. Remove the hex nut and lock washer securing the
driver roller to the shaft.
2. Thread the two 1/4-20 x 1-3/4 cap screws on the
puller four turns into the threaded holes in the drive
roller.
3. Thread and tighten the 5/16-18 x 1-1/4 cap screw
into the puller, shown in Figure 39, until the drive
roller is pulled.
Figure 39. Using the drive roller puller.
4. To re-install, place the drive roller on the shaft, and
thread the lock washer and hex nut onto the shaft
and tighten securely. Note: Do not hammer the drive
roller onto the shaft or you will cause damage to the
shaft.
SERVICE
-27-
W1730 Oscillating Edge Sander
W1730 Wiring Diagram
Disconnect power before
performing any electrical
service. Electricity presents
serious shock hazards that
will result in severe personal
injury and even death!
Emergency
STOP Button
L2/3
L3/5
7
T1/2
T2/4
T3/6
8
Ground
L1/1
RESET
B
1/2
3/4
5/6
12
96
8
10
AMP
6-15 Plug
(As Recommended)
OL Relay
SDE RA-20
Contactor SDE MA-09
A
Ground
G
Hot
98
240
VAC
95
Start Capacitor
400MFD 125VAC
Hot
SERVICE
Run Capacitor
60MFD 250VAC
Motor
2HP
240V
Grnd
-28-
W1730 Oscillating Edge Sander
Troubleshooting
This section covers the most common Model W1730 Oscillating Edge Sander problems. DO NOT make any
adjustments until the Model W1730 is unplugged and moving parts have come to a complete stop.
SYMPTOM
POSSIBLE CAUSE
corrective action
Motor will not start.
1. Low voltage.
2. Open circuit in motor or loose
connections.
1. Check power supply for proper voltage.
2. Inspect all lead connections on motor and magnetic
switch for loose or open connections.
Fuses or circuit breakers
trip open.
1. Short circuit in line cord or plug.
1. Inspect cord or plug for damaged insulation and
shorted wires and replace extension cord.
2. Inspect all connections on motor for loose or
shorted terminals or worn insulation.
3. Install correct fuses or circuit breakers.
2. Short circuit in motor or loose
connections.
3. Incorrect fuses or circuit breakers
in power supply.
Motor overheats.
1. Motor overloaded.
2. Air circulation through the motor
restricted.
1. Reduce load on motor.
2. Clean out motor to provide normal air circulation.
Motor automatically shuts
off (possibly resulting in
blown fuse or tripped
circuit breaker in the
magnetic switch box, or in
power supply circuit).
1. Thermal Protection Circuit Breaker
amperage is set too low.
4. Incorrect fuses/circuit breakers.
1. Unplug machine, open magnetic switch cover,
turn amperage dial on Thermal Protection Circuit
Breaker to a higher amperage setting.
2. Inspect connections on motor for loose or shorted
terminals or worn insulation.
3. Correct the low voltage condition with a qualified
electrician.
4. Install correct fuses or circuit breakers.
Loud, repetitious noise
coming from machine.
1. Pulley setscrews or keys are
missing or loose.
2. Motor fan is hitting the cover.
1. Inspect keys and setscrews. Replace or tighten if
necessary.
2. Tighten fan or shim cover, or replace items.
Machine slows when
operating.
1. Applying too much pressure to
workpiece.
2. Undersized circuit or using
extension cord.
3. Run capacitor is at fault.
1. Sand with less pressure—let the movement of the
belt do the work.
2. Make sure circuit wires are proper gauge & don't
use extension cord!
3. Replace run capacitor.
Machine vibrates
excessively
1. Stand not stable on floor
1. Secure stand to floor, reposition to level surface, or
shim the stand.
2. Check/tighten motor mounts.
3. Replace spring.
4. Adjust idler roller.
5. Replace sanding belt.
2. Short circuit in motor or loose
connections.
3. Low power supply voltage.
2.
3.
4.
5.
Deep sanding grooves or
marks in workpiece.
1. Sanding belt grit too coarse for
the desired finish.
2. Workpiece is being sanded across
the grain.
3. Too much sanding force on
workpiece.
4. Workpiece held still against the
belt.
1. Sanding belt has been stored in an
incorrect environment.
2. Sanding belt has been folded or
smashed.
-29-
1. Use a finer grit sanding belt.
2. Sand with the grain.
3. Reduce pressure on workpiece while sanding.
4. Keep workpiece moving while sanding on the belt.
1. Store sanding belt away from extremely dry or hot
temperature.
2. Hang sanding belt or store unfolded and unstacked.
SERVICE
Grains easily rub off the
belt.
Loose motor mounting.
Weak or broken tension spring.
Idler roller is too loose.
Broken/defective sanding belt.
W1730 Oscillating Edge Sander
SYMPTOM
POSSIBLE CAUSE
corrective action
Glazed Sanding Belt
1. Sanding wet stock.
2. Sanding stock with high residue.
1. Dry stock properly before sanding.
2. Use different stock. Or, accept the characteristics
of the stock and plan on cleaning/replacing belts
frequently.
Burn marks on workpiece
1. Using too fine of sanding belt grit.
2. Using too much pressure against
belt.
3. Work held still for too long.
1. Use a coarser grit sanding belt.
2. Reduce pressure on workpiece while sanding.
1. Using too much pressure against
belt.
2. Sanding softwood.
1. Reduce pressure one workpiece while sanding.
1. Not supporting the workpiece
against the stop.
2. Starting the workpiece on a
leading corner.
1. Use back stop to support workpiece.
Sanding belt clogs quickly
or burns.
Workpiece frequently get
pulled out of your hand.
2. Use different stock. Or, accept the characteristics
of the stock and plan on cleaning/replacing belts
frequently.
2. Start workpiece on a trailing corner.
1. Set belt tracking as described in Setup on Page 17.
1. Tracking/Oscillation out of
adjustment.
SERVICE
Sanding belt comes off
during operation.
3. Do not keep workpiece in one place for too long
and allow to cool.
-30-
74
42
44
43
PARTS
-31-
136
124
45
123
10
75
60
45
30
8
2
7
3
185
6
5
36
4
38
64
67
35
65
68
62
152
66
69
150
151
46
45
47
42
112
114
119
116 115
117
157
84
118
111
112
113
109
122
110 154
108
121
27
181
127-2
127-6
171
127-1
133
134 136
127-3
127-5
60
131
130
60 161 169
29
170
196
148
149
172
192
189
184
198
182
49
99
59
70
92
132
127V2
163
94
93
92
94
D
C
A
U
U
S
T
T
A
H
lw
A IO
sp ay
Z
N
ira s w A R
D
e
th to r
w ar a !
is
h
m
ac en
h in u s
e . in g
23
129
22
160
95
77
56V2
61V2
16
R
E
W
O
NI
P
G
T
N
A
TL A H CE
N
C
E
N
O
!S B G ER
C
O
M
NI
F E SI D
U
D
R
N
B
D
A
S
G
N
93
73
30
D
164
61V2
re
92
92
168
167
24
164
92
58
199
128
89
135
91
90
166
165
191 119
188
187
183 186
185
191
190
197
181
192
194
193
152
39
1
198
195
127-4
176 120
180
150
40
34
37
41
153
41
77
125 77
126
139
185
76
83 158
156
126
122
150
84 155
151
157
121
176 120
157
107
9
90
78
11
5
30 45 60 7
13
12
14
15
16
W1730 Oscillating Edge Sander
Parts Breakdown
73
73
57
101-3
101-2V2
101-1
72
50
25
101-4
PARTS
-3220
18V2
E
D
R
E
N
D
E
R
31
A
19
A
175
173
80
81
82
G
0
G 56
E
3
B O
S
E
LT C
IL
&
L
S AT
P
IN IN
D G
LE 6"
/D X
R 89
U
M "
S
M
O
TO
M
O
R
TO :2
B
H
E
LT R S
P
B
,2
P
S
E
20
E
IZ
L
E
V
E
TA T
,
:6 D:
S
P
B
1 7 S IN
TA LE EE " X
G
25
8
LE
D
B
S
R
:3 9"
L E IZ
S
-P
P
P
E
M
H
:
IN
:2 150
A
O
D PR
6 -3
F
S
S
E
E
C IL L E
C IS /4" P M
D
L A S IZ
US
IO X 1
E
T
2"
N
T
P
S
L A P O IO
G
:1
R
-1
TE R T N S
N
O
/
E
UN
: (2 T R 2 " ,
N
T
2
D
T IL
W
˚-9 ) 4" O KE " , 3
CA
E
IG T0˚:
S
:3 " X
0
H
4-1 T IR
/4"
T:
/2 "
39
O
N
6
LB
S
101V2
166
21
176
17
26
79
75 174
26
178
124
51
179
123
48
87
177 136
181
180
52
88
103
147
142
178
181
177
180
119
84
118
138
145
141
54
86
85
55V2
140 159
141
102
140
146
140
141
184
61V2
162
162
53
142
164
141
71
63
100
97
144
143 140
137
144
136
33
32
28
105
104
106
106
198
184
98
W1730 Oscillating Edge Sander
Parts Breakdown
W1730 Oscillating Edge Sander
Parts Breakdown
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18V2
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
XPSB24M
X1730002
X1730003
X1730004
X1730005
XPFH01
XPS08
XPN07
X1730009
X1730010
X1730011
X1730012
XPS18
X1730014
X1730015
XPW06
X1730017
X1730018V2
X1730019
XPLOGO2
X1730021
X1730022
X1730023
X1730024
X1730025
X1730026
X1730027
XPWR1012
X1730029
X1730030
X1730031
XPAW06M
XPAW05M
X1730034
X1730035
X1730036
X1730037
XPFH01
XPR11M
X1730040
X1730041
XPSB01M
XPSS08
X1730044
X1730045
X1730046
X1730047
XPN05
XPSB11
XPS08
X1730051
X1730052
X1730053
CAP SCREW M5-.8 X 16
FEMALE KNOB 1/4-20
MITER GAUGE BODY
MITER BAR
T-SLOT WASHER
FLAT HD SCR 10-24 X 3/8
PHLP HD SCR 10-24 X 3/4
HEX NUT 10-24
PIVOT PIN
STOP SHAFT
POINTER BODY
POINTER PLATE
PHLP HD SCR 10-24 X 1/4
STUD 1/4-20 X 1-1/4
PLASTIC WASHER 1/4
FLAT WASHER 1/4
DOOR W/LATCH
MACHINE ID LABEL CSA V2.10.11
READ MANUAL LABEL
SF LOGO 3-3/4 X 8-1/8
MODEL NUMBER LABEL
DISCONNECT LABEL
DUST HAZARD LABEL
SAFETY GLASSES LABEL
ELECTRICITY LABEL
TABLE ADJUSTMENT LABEL
ROD
WRENCH 10 X 12MM
PLATE 70 X 31.7 X 8
POINTER
WOOD BOARD 25 X 395 X 457
HEX WRENCH 6MM
HEX WRENCH 5MM
TABLE INSERT 4"
TABLE INSERT 3"
TABLE INSERT 2-1/2"
TABLE INSERT 1-1/2"
FLAT HD SCR 10-24 X 3/8
EXT RETAINING RING 25MM
IDLER ROLLER COVER
TABLE MOUNTING BRACKET
CAP SCREW M6-1 X 16
SET SCREW 5/16-18 X 1/2
HEX SPINDLE FRONT COVER
SLEEVE
HEX SPINDLE
HEX SPINDLE BACK COVER
HEX NUT 1/4-20
CAP SCREW 5/16-18 X 1-1/4
PHLP HD SCR 10-24 X 3/4
EMERGENCY STOP PWR CORD
MOTOR POWER CORD
CONDUIT CONNECTOR 3/8"
54
55V2
56V2
57
58
59
60
61V2
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
97
98
99
100
101V2
101-1
101-2V2
101-3
101-4
102
103
X1730054
X1730055V2
X1730056V2
XPWRCRD220L
X1730058
X1730059
X1730060
X1730061V2
X1730062
X1730063
X1730064
X1730065
X1730066
X1730067
X1730068
X1730069
XPB57
X1730071
X1730072
XPS06
X1730074
X1730075
XPB03
XPSB05
X1730078
X1730079
X1730080
XP6001
X1730082
XPCB06
XPLN03
X1730085
XPFH05
X1730087
X1730088
X1730089
XPW02
X1730091
XPN32M
X1730093
X1730094
XPW06
X1730097
X1730098
X1730099
X1730100
X1730101V2
X1730101-1
X1730101-2V2
X1730101-3
X1730101-4
XPN03M
X1730103
PLASTIC CONDUIT 3/8" X 11"
PLASTIC CONDUIT 3/8" X 12" V2.09.11
PLASTIC CONDUIT 3/8" X 18" V2.09.11
POWER CORD
GUARD
COVER/DUST PORT
GREASE FITTING
CONDUIT CONNECTOR 3/8" V2.09.11
SANDING DRUM SPINDLE
ADJUSTMENT LABEL
RUBBER DRUM 3"
RUBBER DRUM 2"
RUBBER DRUM 1-1/2"
SANDING SLEEVE 3"
SANDING SLEEVE 2"
SANDING SLEEVE 1-1/2"
HEX BOLT 1/4-20 X 1/4
FENCE
EXTENDABLE COVER
PHLP HD SCR 10-24 X 3/8
HANDWHEEL
ROTATION LABEL
CAP SCREW 5/16-18 X 1
CAP SCREW 1/4-20 X 3/4
TABLE
HINGE PIN 8 X 45MM
ECCENTRIC BOLT
BALL BEARING 6001ZZ
ACORN NUT 3/8-16
CARRIAGE BOLT 5/16-18 X 1-1/4
LOCK NUT 5/16-18
SCALE PLATE
FLAT HD SCREW 1/4-20 X 3/4
MITER GAUGE SPACER
ANGLE GAUGE LABEL
HANDLE 3/8-16 X 50
FLAT WASHER 3/8
SPECIAL NUT 3/8-16
HEX NUT M14-2
TIE ROD
ADJUSTING ROD
FLAT WASHER 1/4”
ECCENTRIC
BACK STOP
GRAPHITE PAPER
SANDING BELT 6 X 89
MAGNETIC SWITCH V2.10.11
CONTACTOR SDE MA-09 220–240V
OL RELAY SDE RA-20 8-12A V2.10.11
MAG SWITCH FRONT COVER
MAG SWITCH REAR COVER
HEX NUT M8-1.25
SET SCREW NPT 1/8
-33-
PARTS
REF
W1730 Oscillating Edge Sander
PARTS
Parts Breakdown
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127V2
127-1
127-2
127-3
127-4
127-5
127-6
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
X1730104
X1730105
XPS12
X1730107
X1730108
XPSB07
X1730110
X1730111
X1730112
X1730113
X1730114
X1730115
X1730116
X1730117
X1730118
XPSB04
X1730120
X1730121
X1730122
X1730123
X1730124
X1730125
X1730126
X1730127V2
X1730127-1
X1730127-2
XPC400A
X1730127-4
X1730127-5
X1730127-6
X1730128
X1730129
XPLW06
XPN04
XPB18
X1730133
XPB09
X1730135
XPSS08
X1730137
X1730138
XPSB16
XP6202
XPR41M
X1730142
X1730143
X1730144
X1730145
X1730146
XPSB19M
X1730148
GEAR BOX COVER
HANDLE
PHLP HD SCR 1/4-20 X 5/8
ADJUSTING PLATE
RACK & PINION BOX
CAP SCREW 5/16-18 X 3/4
COPPER RING
PINION GEAR
SPACER
PINION SPINDLE
COPPER RING
PINION ROD
COVER PLATE
BALL BEARING 38 X 42 X 20T
SPINDLE
CAP SCREW 1/4-20 X 1/2
LOCK COLLAR
HANDLE BAR
FEMALE KNOB 3/8-16
COPPER INSERT 5 X 3
HANDLE 1/4 X 1/2
RACK GEAR
SPINDLE
MOTOR 2HP 240V 1PH V2.10.11
ELCTRICAL BOX
CAPACITOR COVER
S CAPACITOR 400MFD/125V
FAN
FAN COVER
R CAPACITOR 60M 250V 1-3/8 x 3-3/8
DRIVE ROLLER
DUST PORT
LOCK WASHER 5/8
HEX NUT 5/8-11
HEX BOLT 3/8-16 X 1
GEAR BOX FIXING PLATE
HEX BOLT 5/16-18 X 1/2
SPINDLE CONNECTOR
SET SCREW 5/16-18 X 1/2
GEAR BOX
WORM GEAR
CAP SCREW 3/8-16 X 3/4"
BALL BEARING 6202Z
INT. RETAINING RING 35MM
OIL SEAL WITHOUT HOLE
DRIVE SHAFT
OIL SEAL WITH HOLE
WORM SHAFT
KEY 7 X 7 X 16
CAP SCREW M8-1.25 X 75
IDLER ROLLER BRACKET
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
X1730149
X1730150
XPB09
XP6205
X1730153
X1730154
X1730155
X1730156
XPSB17M
X1730158
X1730159
XPS09
XP5101
XPSB04
X1730163
X1730164
X1730165
XPS08
X1730167
XPN07
XPB43M
XPLN09M
X1730171
XPSB18
X1730173
X1730174
XPB21
XPN08
X1730177
XPB82
XPLN12M
XPB09
XPLW01
X1730182
X1730183
XPW07
XPSB30
XPN13
X1730187
X1730188
X1730189
X1730190
XPSB05
XPLN02
X1730193
XPW14
XPN04
XPSB32
X1730197
XPSB03
X1730199
IDLER ROLLER SPINDLE
SPECIAL WASHER 5/16
HEX BOLT 5/16-18 X 1/2
BALL BEARING 6205Z
IDLER ROLLER
KNOB 3/8-16 X 1
TABLE SPINDLE
KEY 8 X 8 X 315
CAP SCREW M4-.7 X 10
U-TYPE CAST IRON TABLE
ALUMINUM RING
PHLP HD SCR 1/4-20 X 1/4
THRUST BALL BEARING 5101
CAP SCREW 1/4-20 X 1/2
PLATEN COVER
STAR KNOB 5/16-18 X 1
EMERGENCY STOP SWITCH
PHLP HD SCR 10-24 X 3/4
SWITCH COVER
HEX NUT 10-24
HEX BOLT M12-1.75 X 75
HEX NUT M12-1.75
MOTOR BRACKET
CAP SCREW 1/4-20 X 1-3/4
BASE
GEAR CABINET
HEX BOLT 3/8-16 X 3/4
HEX NUT 3/8-16
SWIVEL BRACKET
HEX BOLT 3/4-10 X 2-1/4
LOCK NUT 3/4-10
HEX BOLT 5/16-18 X 1/2
LOCK WASHER 5/16”
PLATEN
TENSIONING LINK ARM
FLAT WASHER 5/16
CAP SCREW 5/16-18 X 1/2
NUT 1/2-13
HANDLE BAR
FEMALE KNOB 1/2-13
SPINDLE BRACKET
SPINDLE
CAP SCREW 1/4-20 X 3/4
LOCK NUT 1/4-20
CONDENSED SPRING
FLAT WASHER 5/8
LOCK NUT 5/8-11
CAP SCREW 1/4-20 X 1-1/4
SHAFT
CAP SCREW 5/16-18 X 1
STRAIN RELIEF
-34-
WARRANTY REGRISTRATION
Name___________________________________________________________________________________________
Street___________________________________________________________________________________________
City_______________________________________________________________ State________Zip______________
Phone Number_______________________E-Mail_______________________FAX_________ ____________________
Model #
Serial #
Dealer Name
Purchase Date /
/
The following information is given on a voluntary basis and is strictly confidential.
1.
How did you first learn about us?
9.
CUT ALONG DOTTED LINE
___Advertisement
___Friend
___Mail order Catalog
___Local Store
___World Wide Web Site
___Other__________________________________________________
2.
Which of the following magazines do you subscribe to.
___Cabinetmaker
___WOOD
___Family Handyman
___Wooden Boat
___Fine Homebuilding
___Woodshop News
___Woodsmith___Today’s Homeowner
___Home Handyman
___Woodwork
___Journal of Light Construction
___Woodworker
___Old House Journal
___Woodworker’s Journal
___Popular Mechanics
___Workbench
___Popular Science
___American How-To
___Popular Woodworking
___Other__________________________________________________
3.
Which of the following woodworking/remodeling shows do you watch?
___Backyard America
___The New Yankee Workshop
___Home Time
___This Old House
___The American Woodworker
___Woodwright’s Shop
___Other__________________________________________________
4.
What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
5.
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
What is your age group?
___20-29___50-59
___30-39___60-69
___40-49___70 +
___Air Compressor
___Panel Saw
___Band Saw___Planer
___Drill Press
___Power Feeder
___Drum Sander
___Radial Arm Saw
___Dust Collector
___Shaper
___Horizontal Boring Machine
___Spindle Sander
___Jointer___Table Saw
___Lathe
___Vacuum Veneer Press
___Mortiser
___Wide Belt Sander
___Other__________________________________________________
10.
How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
7.
How would you rank your woodworking skills?
Which benchtop tools do you own? Check all that apply.
___1" x 42" Belt Sander
___6" - 8" Grinder
___5" - 8" Drill Press
___Mini Lathe
___8" Table Saw
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
___Disc/Belt Sander
___Mini Jointer
___Other__________________________________________________
11.
Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander
___Orbital Sander
___Biscuit Joiner
___Palm Sander
___Circular Saw
___Portable Planer
___Detail Sander
___Saber Saw
___Drill/Driver___Reciprocating Saw
___Miter Saw___Router
___Other__________________________________________________
12. What machines/supplies would you like to see?
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
13. What new accessories would you like Woodstock International to carry?
__________________________________________________________
__________________________________________________________
14.
6.
What stationary woodworking tools do you own? Check all that apply.
Do you think your purchase represents good value?
___Yes___No
___8 - 20 Years
___20+ Years
___Simple___Advanced
___Intermediate
___Master Craftsman
8.
How many Shop Fox® machines do you own? ___________________
15.
Would you recommend Shop Fox® products to a friend?
___Yes___No
16.Comments:________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, wa 98227-2309
FOLD ALONG DOTTED LINE
tape along edges--please do not staple
WARRANTY
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workmanship and materials for a period of 2 years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone
other than Woodstock International, Inc.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within 2
years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect
through inspection. If it is determined there is no defect, or that the defect resulted from causes not
within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost
of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durability standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
High Quality Machines and Tools
Woodstock International, Inc. carries thousands of products designed
to meet the needs of today's woodworkers and metalworkers.
Ask your dealer about these fine products: