Sharp R-308F Owner`s manual

Owner’s Manual
Installation and Operation
Models:
BIR42
Wood Burning Fireplace
DO NOT DISCARD THIS MANUAL
•
Important operating •
and maintenance
instructions included.
Read, understand
and follow these
instructions for safe
installation and
operation.
WARNING
•
Leave this manual with
party responsible for
use and operation.
WARNING
HOT SURFACES!
If the information in these instructions is not followed exactly, a
fire may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire. Overfiring will void your
warranty.
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
Installation and service of this fireplace
should be performed by qualified personnel.
Hearth & Home Technologies suggests NFI
certified or factory-trained professionals, or
technicians supervised by an
NFI certified professional.
T
O
N RD
O A
D SC
I
D
NOTICE
Screen/mesh, glass doors and
other surfaces are hot during
operation AND cool down.
Hot screen/mesh and glass doors will cause burns.
• Do not touch screen/mesh or glass doors until cooled
• NEVER allow children to touch screen/mesh or glass
doors
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
WARNING
Fire Risk
• For use with solid wood fuel or decorative
gas appliance only.
• Do not install unvented gas logs.
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
1
Read this manual before installing or operating this fireplace.
Please retain this owner’s manual for future reference.
Congratulations!
Congratulations on selecting a Heatilator wood burning
fireplace. The Heatilator fireplace you have selected is
designed to provide the utmost in safety, and reliability.
This owner’s manual should be retained for future reference. We suggest you keep it with your other important
documents and product manuals.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heatilator wood burning fireplace will give you
years of durable use and trouble-free enjoyment. Welcome
to the Heatilator family of fireplace products!
Homeowner Reference Information
We recommend that you record the following pertinent
information about your fireplace:
Model Name:
Date purchased/installed:
Serial Number:
Location on fireplace:
Dealership purchased from:
Dealer phone:
Notes:
Listing Label Information/Location
The model information regarding your specific fireplace can be found on the rating plate located on the smoke shield of
the fireplace.
Serial
Number
Fireplace
Model
Grate
FIREPLACE NO.
WARNING: RISK OF
FIRE DAMAGE. REPLACE
GRATE WITH HEARTH & HOME
TECHNOLOGIES INC.
MODEL NO.
MODEL NO.
MFG. DATE
FIRECHAMBER INTENDED FOR USE WITH HEARTH & HOME TECHNOLOGIES INC. LISTED FIREPLACE PARTS. SEE INSTALLATION AND
OPERATING INSTRUCTIONS FOR THIS MODEL. ONLY HEARTH & HOME TECHNOLOGIES INC. GLASS DOOR KITS CAN BE INSTALLED ON THIS UNIT.
FIREPLACE ALSO FOR USE
IN MANUFACTURED HOMES
FAN KIT
MODEL NO.
YES
CLEARANCE TO
COMBUSTIBLES:
NO
&
DO NOT OVERFIRE. USE ONLY: SOLID WOOD FUEL OR
LISTED DECORATIVE GAS APPLIANCE. DO NOT USE A
FIREPLACE INSERT OR OTHER PRODUCTS NOT
SPECIFIED FOR USE WITH THIS PRODUCT. IF DOORS
ARE USED OPERATE FIREPLACE WITH DOORS FULLY
OPEN OR CLOSED ONLY. WHEN BURNING A
DECORATIVE GAS APPLIANCE IN THE FIREPLACE,
ADJUST DAMPER TO THE FULLY OPEN POSITION.
2
CHIMNEY
2 IN. MIN.
IN.
MIN.
FIREBOX
RATED AT
115 VOLTS, 50/60 Hz.,
AMP.
WARNING! THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED
GAS LOG SET. TO REDUCE THE RISK OF FIRE OR INJURY, DO NOT
INSTALL AN UNVENTED GAS LOG SET INTO FIREPLACE.
WARNING! THIS APPLIANCE IS NOT FOR USE AS COOKING EQUIPMENT.
IF INSTALLATION OR OPERATING INSTRUCTIONS ARE MISSING
CONTACT: HEARTH & HOME TECHNOLOGIES INC.,
1915 W. SAUNDERS ST., MT. PLEASANT, IA 52641.
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
•
•
•
•
!
Safety Alert Key:
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates practices which may cause damage to the fireplace or to property.
Table of Contents
Congratulations! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1
8
A.
B.
C.
D.
E.
F.
G.
H.
I.
Listing and Code Approvals
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . 6
B. Non-Combustible Materials . . . . . . . . . . . . . . . . . . . . . 6
C. Combustible Materials . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Operating Instructions
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
3
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Seasoned Wood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Starting a Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Grate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Firescreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Flue Damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Outside Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Molded Brick Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Glass Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Vented Gas Log Sets & Gas Log Lighters . . . . . . . . . . 9
Optional Components . . . . . . . . . . . . . . . . . . . . . . . . . 9
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wood Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintainance and Service
A.
B.
C.
D.
E.
Disposal of Ashes . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chimney Inspection/Cleaning . . . . . . . . . . . . . . . . . . 11
Check Firebox Molded Brick Panel . . . . . . . . . . . . . . 12
Inspect Grate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4
Troubleshooting Guide
5
Getting Started
A.
B.
C.
D.
E.
F.
G.
H.
6
7
Typical Fireplace System. . . . . . . . . . . . . . . . . . . . . . 14
Design and Installation Considerations . . . . . . . . . . . 15
Draft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Negative Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Locating your Fireplace & Chimney. . . . . . . . . . . . . . 16
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . 17
Typical Fireplace Components . . . . . . . . . . . . . . . . . 17
Inspect Fireplace and Components . . . . . . . . . . . . . . 17
Select Fireplace Location . . . . . . . . . . . . . . . . . . . . . 18
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sidewalls/Surrounds . . . . . . . . . . . . . . . . . . . . . . . . . 20
Frame the Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation of Fireplace
A.
B.
C.
D.
E.
9
Chimney Requirements . . . . . . . . . . . . . . . . . . . . . . . 25
Using Offsets/Returns . . . . . . . . . . . . . . . . . . . . . . . . 26
Assemble Chimney Sections . . . . . . . . . . . . . . . . . . . 27
Install Ceiling Firestops . . . . . . . . . . . . . . . . . . . . . . . 28
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . 29
Cut Out Hole in Roof . . . . . . . . . . . . . . . . . . . . . . . . . 30
Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . 30
Install Flashing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chimney Termination Requirements . . . . . . . . . . . . . 31
Chase Installations
A.
B.
C.
D.
Construct the Chase . . . . . . . . . . . . . . . . . . . . . . . . . 32
Install Fireplace & Chimney . . . . . . . . . . . . . . . . . . . . 33
Install Chase Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Install Termination Cap . . . . . . . . . . . . . . . . . . . . . . . 34
10 Shrouds
A. Radiation Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
B. Field Constructed Shrouds . . . . . . . . . . . . . . . . . . . . 36
11 Installation of Molded Brick Panel
A.
B.
C.
D.
E.
F.
G.
Install Hearth Molded Brick Panel . . . . . . . . . . . . . . . 38
Install Side Molded Brick Panel/Traditional . . . . . . . . 38
Install Back Molded Brick Panel/Traditional . . . . . . . 38
Install Side Molded Brick Panel - Herringbone . . . . . 39
Install Back Molded Brick Panel - Herringbone . . . . . 39
Install Mortar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Install Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
12 Finishing
Framing & Clearances
A.
B.
C.
D.
Chimney Assembly
Things to Consider . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Position the Fireplace . . . . . . . . . . . . . . . . . . . . . . . . 21
Place Protective Metal Hearth Strips . . . . . . . . . . . . . 21
Level Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Install Outside Air Kit . . . . . . . . . . . . . . . . . . . . . . . . . 23
A.
B.
C.
D.
E.
F.
G.
Non-Combustible Materials . . . . . . . . . . . . . . . . . . . . 41
Combustible Materials . . . . . . . . . . . . . . . . . . . . . . . . 41
Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Finishing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Combustible Mantel . . . . . . . . . . . . . . . . . . . . . . . . . 45
Mantel, Adding Extra Support . . . . . . . . . . . . . . . . . . 46
Sidewalls/Surrounds . . . . . . . . . . . . . . . . . . . . . . . . . 47
13 Accessories
A. Gas Log/Lighter Provision . . . . . . . . . . . . . . . . . . . . . 48
B. Wood Burning Inserts . . . . . . . . . . . . . . . . . . . . . . . . 48
14 Reference Materials
A.
B.
C.
D.
E.
Fireplace Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 49
Optional Components . . . . . . . . . . . . . . . . . . . . . . . . 50
Chimney Components . . . . . . . . . . . . . . . . . . . . . . . . 51
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Note: An arrow (Î) found in the text signifies change in content.
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
3
Î
Warranty
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood,
pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or
Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Components Covered
Gas
Wood
Pellet
EPA
Wood
Electric
Venting
X
X
X
X
X
X
X
X
Igniters, Electronic Components, and Glass
X
X
Blowers
X
X
All Parts and Material Except as
covered by Conditions, Exclusion, and Limitations listed
X
3 years
Molded Refractor y Panels
X
Firepots
5 years
3 years
7 years
3 years
10
years
1 year
X
Burners, Logs & Refractor y
Limited
Lifetime
1 year
X
Firebox & Heat Exchanger
90 Days
X
X
X
X
X
Castings & Baf ?es
X
X
Firebox, HHT Chimney, Termination & Heat
Exchanger
X
X
X
See Conditions, Exclusions, and limitations.
X
All Replacement Parts
9-01-08
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
This warranty applies to the original owner and is transferable up to two years from date of purchase to the new
homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance
remains in its original place of installation.
The maximum amount recoverable under this warranty is limited to the purchase price of the product.
In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home
is not covered under this warranty.
4021-645A 09-01-08
4
Page 1 of 2
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
This limited warranty does not extend to or include surface ?nish on the appliance or terminations, door gasketing, glass
gasketing, glass discoloration, ?rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion
on any of the metal surfaces, cast iron components, baf?es, ?repots, doors, or ?rebox area are not covered by this
warranty.
Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to
this noise are not covered by this warranty.
HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or
maintenance of the appliance not in accordance with the installation instructions; operating instructions and the
listing agent identi?cation label furnished with the appliance; (2) installation which does not comply with local building
codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4)
environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure
or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than
those speci?ed in the operating instructions; (6) installation or use of components not supplied with the appliance or
any other components not expressly authorized and approved by HHT; and/or (7) modi?cation of the appliance not
expressly authorized and approved by HHT in writing.
This warranty does not apply to non-HHT venting components, hearth components or other accessories used in
conjunction with the installation of this product.
This warranty is void if the appliance has been over-?red or operated in atmospheres contaminated by chlorine,
?uorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or
there is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship
during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the
defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you speci?c rights; you may also have other rights, which vary from state to state.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all
warranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide
necessary parts or components, contact the nearest authorized HHT dealer or supplier.
4021-645A 09-01-08
Page 2 of 2
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
5
1
Listing and Code Approvals
A. Appliance Certification
This fireplace system has been tested and listed in accordance with UL 127 standards by Underwriters Laboratories
Inc. for installation and operation in the United States.
B. Non-Combustible Materials
•
This fireplace may be installed in sleeping rooms EXCEPT
in manufactured homes. If installed with a gas log set, provisions for the National Fuel Gas Code must be met.
This fireplace has been tested and listed for use with
the optional components specified in this manual. These
optional components may be purchased separately and
installed at a later date.
•
NOTICE: The outside air kits must be installed at the time of
fireplace installation.
•
Heatilator is a registered trademark of Hearth & Home
Technologies Inc.
Materials which will not ignite and burn, composed of any
combination of the following:
- Steel
- Iron
- Brick
- Tile
- Concrete
- Slate
- Glass
- Plasters
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C
C. Combustible Materials
•
Materials made of or surfaced with any of the following
materials:
- Wood
- Compressed paper
- Plant fibers - Plastic
Any material that can ignite and burn; flame proofed or
not, plastered or un-plastered
WARNING! Risk of Fire! Hearth & Home Technologies
disclaims any responsibility for, and the warranty and
agency listing will be voided by the actions below.
DO NOT:
• install or operate damaged fireplace
• modify fireplace
• install other than as instructed by Hearth & Home
Technologies
• operate the fireplace without fully assembling all
components
• overfire
• install an unvented gas log set
• install any component not approved by Hearth &
Home Technologies
• install parts or components not Listed or approved
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
Notice: This fireplace is tested and approved as a decorative
fireplace. It should not be factored as a primary heat source
in residential heating calculations.
6
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
User Guide
2
Operating Instructions
WARNING
HOT SURFACES!
Screen/mesh, glass doors and other surfaces are hot during operation AND cool down.
Hot screen/mesh and glass doors will cause burns.
• Do not touch screen/mesh or glass doors until cooled
• NEVER allow children to touch screen/mesh or glass doors
• Keep children away
• CAREFULLY SUPERVISE children in same room as fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable materials.
• Keep clothing, furniture, draperies and other flammable materials away.
If you expect that children may come into contact with this fireplace, we recommend a barrier such as a decorative
screen. See your dealer for suggestions.
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace
according to operating instructions could cause fire or injury.
A. Your Fireplace
Molded Brick Panels
Section 2.H.
Ma
nte
l
Grate
Section 2.D.
Gas Log Set
Gas Log Lighters
(not shown)
Section 2.J.
Firescreen
(not shown)
Section 2.E.
Wood Fuel
Section 2.M.
Hearth
Glass Doors
(not shown)
Section 2.I.
Clear Space
Section 2.L.
Figure 2.1
Outside Air Control Handles
Section 2.G.
Turn handle to unlock,
pull towards the inside
of the fireplace to open.
Reverse steps to close & lock.
Flue Damper
Section 2.F.
UP to Open
DOWN to Close
General Operating Parts
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
7
B. Seasoned Wood
D. Grate
Properly seasoned wood is important for successful operation of your fireplace. Most woodburning fireplace problems
are caused by burning wet, unseasoned wood.
This fireplace is designed to be used with the grate supplied with this unit or one approved by HHT. The grate will
deteriorate over time and will need occasional replacement.
Seasoned firewood is wood that is cut to size, split and air
dried to a moisture content of around 20%.
Imagine a wooden bucket that weighs about eight pounds.
Fill it with a gallon of water, put it in the fireplace and try to
burn it. This sounds ridiculous but that is exactly what you
are doing if you burn unseasoned wood.
WARNING! Risk of Fire! Use only the factory-supplied
integral grate.
• Keeps logs in place.
• Allows proper air circulation around the fire.
A tree cut down a year ago and not split is likely to have
almost as high a moisture content now as it did when it was
cut.
E. Firescreen
Please refer to Section 2.M. for more detail.
WARNING! Risk of Fire or Burns!
• Screen will not prevent burning materials from falling
out.
• Screen pulls or handles may be hot.
C. Starting a Fire
NOTICE: You must establish a good draft to prevent smoke
spillage into the room.
The firescreen is provided to control sparks. Keep it closed
when the fireplace is in use.
F. Flue Damper
WARNING! Risk of Fire! Keep combustible materials,
gasoline and other flammable vapors and liquids clear of
the fireplace.
DO NOT:
• store flammable materials close to the fireplace
• use gasoline, lantern fuel, kerosene, charcoal lighter
fluid or similar liquids to start or “freshen up” a fire in
this fireplace.
Keep all flammable liquids well away from the fireplace while
it is in use. Combustible materials may ignite.
•
•
•
G. Outside Air
The first three or four fires should be of moderate size to
allow the oils and binders to be burned from the fireplace
and molded brick panel, and paint to cure. You may notice
an industrial odor the first few fires. This is considered
normal.
Use well-seasoned wood (see Section 2.M.).
Open the flue damper to a fully open position.
Open outside air.
Place crumpled or twisted paper under the fireplace
grate.
Loosely arrange kindling or small pieces of wood to form
a ‘tent’ on the fireplace grate.
Pre-warm the flue to establish a draft to help reduce smoke
spillage during start-up. Hold a rolled up piece of burning
newspaper under the flue damper for a few moments.
Light the crumpled paper to ignite the kindling.
Add small pieces of wood until a hot bed of embers has
been established.
Add a minimum of three average size pieces of split
firewood, placed to allow combustion air and flames
between them.
•
•
•
•
•
•
•
•
•
CAUTION! Odors and vapors released during initial operation may be irritating to sensitive individuals. Open
windows for air circulation.
8
•
Refer to Figure 2.1 for location of control.
Must be in fully open position (handle up toward the top
of the fireplace) during operation of the fireplace.
Before lighting the fireplace, verify fully open position by
looking up from the inside of the fireplace.
WARNING! Risk of Fire and Asphyxiation! Open
damper prior to operating fireplace. A closed damper
overfires the fireplace and will cause smoke and flames
to spill into the room.
•
•
•
Refer to Figure 2.1 for location of controls.
Outside air doors should be in the fully opened position
during operation of the fireplace.
Before lighting the fireplace, turn both handles & pull out
to open. Reverse steps to close and lock.
H. Molded Brick Panel
•
•
•
•
The molded brick panel is shipped separately, but required
to contain heat and provide an attractive interior.
It will deteriorate over time and will need occasional
replacement. Small hairline cracks and discoloration are
normal and do not affect its safety.
Cracks in the mortar may occur and do not affect the
safety of the unit. If mortar falls out of the joints and metal
is exposed, replace or patch the mortar.
(See Molded Brick Panel Maintenance, Section 3.C.)
WARNING! Risk of Fire! DO NOT burn fireplace without
molded brick panel. Use only molded brick panel supplied
by Hearth & Home Technologies, Inc.
NOTICE: Do not substitute for HHT mortar. Other materials
may stain the molded brick panels.
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
I. Glass Doors
J. Vented Gas Log Sets & Gas Log Lighters
•
•
•
•
Glass and screen doors are optional.
Refer to Figure 2.2 for proper use.
WARNING! Risk of Fire! Install ONLY doors approved by
Hearth & Home Technologies, Inc.
WARNING! Risk of Fire or Asphyxiation!
WARNING! Risk of Fire and Smoke! Fireplaces equipped
with doors should be operated only with doors fully open
or doors fully closed. If doors are left partly open, gas and
flame may be drawn out of the fireplace opening.
FULLY OPEN
CORRECT
PARTLY OPEN
INCORRECT
Optional
Vented gas logs or gas log lighters can be installed in
this fireplace. Follow the instructions provided with the
accessory for operation.
• DO NOT install unvented gas logs.
• Damper must be locked open.
• Gas flame may generate fumes.
K. Optional Components
•
•
Other options may be available
Consult your dealer/distributor
WARNING! Risk of Fire! DO NOT install and or use any
component not approved by Hearth & Home Technologies Inc.
FULLY CLOSED
CORRECT
Figure 2.2
PARTLY CLOSED
INCORRECT
Operating Positions of Bi-fold Doors
L. Clear Space
WARNING! DO NOT place combustible objects in front of
the fireplace. High temperatures may ignite clothing, furniture or draperies.
• DO NOT place combustible objects within 48 in. (121.9 cm)
of the front of fireplace. See Figure 2.3.
• Mantel - avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these
objects.
48 in. (121.9 cm)
Clear Space
Front of Fireplace
24 in. (61.0 cm)
Clear Space
Sides of Fireplace Opening
Figure 2.3
Clear Space
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
9
M. Wood Fuel
Seasoned Wood
Hardwood vs Softwood
•
•
•
Your fireplace performance depends on the quality of the
firewood you use.
•
•
•
•
•
•
•
Seasoned wood contains about 8,000 BTUs per pound .
Hard woods are more dense than soft woods.
Hard woods contain 60% more BTUs than soft woods.
Hard woods require more time to season, burn slower and
are harder to ignite.
Soft woods require less time to dry, burn faster and are
easier to ignite.
Start the fire with soft wood to bring the fireplace up to
operating temperature and to establish draft.
Add hard wood for slow, even heat and longer burn
time.
Soft woods
Hard woods
•
•
•
•
•
•
•
•
•
•
•
Douglas Fir
Pine
Spruce
Cedar
Poplar
Aspen
Alder
Oak
Maple
Apple
Birch
Cut logs to size
Split to 6 in. (152 mm) or less
Air dry to a moisture content of around 20%
- Soft wood - about nine months
- Hard wood - about eighteen months
NOTICE: Seasoning time may vary depending on drying
conditions.
Storing Wood
Steps to ensure properly seasoned wood:
•
•
•
•
•
Stack wood to allow air to circulate freely around and
through woodpile.
Elevate wood pile off ground to allow air circulation
underneath.
Smaller pieces of wood dry faster. Any piece over 6 in.
(152 mm) in diameter should be split.
Wood (whole or split) should be stacked so both ends of
each peice are exposed to air. More drying occurs through
the cut ends than the sides.
Store wood under cover to prevent water absorbtion
from rain or snow. Avoid covering the sides and ends
completely.
WARNING! Fire Risk! DO NOT store wood:
• in front of the fireplace.
• in space required for loading or ash removal.
Moisture
WARNING! Risk of Fire!
• DO NOT burn wet or green wood.
• Wet, unseasoned wood can cause accumulation of
creosote.
The majority of the problems fireplace owners experience
are caused by trying to burn wet, unseasoned wood.
•
•
Wet, unseasoned wood requires energy to evaporate the
water instead of heating your home, and
Evaporating moisture cools your chimney, accelerating
formation of creosote.
10
Processed Solid Fuel Firelogs
Manufactured firelogs may be used with this fireplace.
Hearth & Home Technologies Inc. recommends the use of
UL Classified processed fuel firelogs. Follow the manufacturer’s lighting and safety instructions.
Using firelogs may require more frequent chimney inspection and cleaning.
Do not poke or stir the logs while they are burning. Use
only firelogs that have been evaluated for the application in
manufactured fireplaces and refer to firelog warnings and
caution markings on packaging prior to use.
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
3
Maintainance and Service
A. Disposal of Ashes
B. Chimney Inspection/Cleaning
Frequency: When they reach bottom of grate
By: Homeowner
Frequency: At least twice a year during heating season or
as recommended by a certified chimney sweep
By: Certified chimney sweep
WARNING! Risk of Fire! Ashes could contain hot embers.
• Place ashes in a metal container with a tight-fitting lid.
• The closed container should be placed on a noncombustible
floor or on the ground, well away from all combustible
materials, pending final disposal.
• If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
WARNING! Risk of Fire! Ignited creosote is extremely
HOT. Prevent creosote buildup.
Refer to Figure 3.1 to remove/reinstall termination caps.
Creosote - Formation and Need for Removal
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture to
form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result,
creosote residue accumulates on the flue lining. When
ignited this creosote makes an extremely hot fire.
WARNING! Risk of Fire! A chimney fire can permanently
damage your chimney system and nearby structures.
In the event of a chimney fire, Hearth & Home Technologies Inc. recommends
•
•
replacement of the chimney, and
inspection of the adjacent structure to the provisions of
NFPA Level III inspection criteria
The chimney shall be inspected at least twice a year during
the heating season to determine when a creosote buildup
has occurred.
When creosote has accumulated it shall be removed to
reduce the risk of a chimney fire.
Remove 4 screws
and lift top pan off.
Remove 2 screws from
the front and back and
lift the top off.
ST1175
Square Termination Cap
TCT1175
Terra Cotta
Termination Cap
Remove screws,
lift top cover. Top Cover
Cap
Cap
Chimney
Slip
Section
TR11/TR11T/TR11-TV
Round Termination Cap
Figure 3.1
Chimney & Termination Cap Cleaning
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
11
C. Check Firebox Molded Brick Panel
Frequency: After each ash removal
By: Homeowner
WARNING! Risk of Fire! Inspect fireplace molded brick
panel. Crumbling, deteriorated molded brick panel can allow overheating of surrounding materials.
Expansion and contraction will cause minor cracking of the
molded brick panel. This is normal. The panel will require
periodic replacement depending on use.
The panels should be replaced if
•
•
•
Cracks exceed ¼ inch (6 mm) in width,
Metal is exposed behind a panel,
Large pieces of panel fall out.
NOTICE: Do not substitute for HHT mortar. Other materials
may stain the molded brick panels.
D. Inspect Grate
Frequency: After each ash removal
By: Homeowner
Inspect grate for:
• Warping or sagging 1-1/2 in. (38 mm) or more
• Broken welds
• Burn-through of grate bars
For safe operation, replace only with the approved grate
from Hearth & Homes Technologies Inc.
E. Glass Cleaning
Frequency: As desired
By: Homeowner
CAUTION! Handle glass assembly with care. Glass is
breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• Do not clean glass while it is hot
Clean glass with a non-abrasive commercially available
cleaner or ashes:
•
•
Light deposits
- Use household glass cleaner
Heavy deposits
- Use wood ash on damp cloth or,
- Use commercial fireplace glass cleaner (consult with
your dealer)
12
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
4
Troubleshooting Guide
Start Fire Problems
Possible Cause
Solution
Can’t get fire started
Excessive smoke or spillage
Burns too slowly
Smolders, sizzles
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange kindling & wood for
air movement.
Damper closed/not fully open
Open damper.
Not enough air for fire to ignite
Check for restricted cap/shroud.
Check for flue blockage.
Pre-warm flue before starting fire (refer to starting fire
section).
Check for adequate vent height (refer to chimney assembly
section).
Open window below the fireplace towards the wind.
Open outside air doors.
Wood condition is too wet, too large
Use dry, seasoned wood (refer to wood fuel section).
Bed of coals not established before
adding wood
Start with paper & kindling to establish bed of coals (refer to
starting fire section).
Flue blockage such as birds’ nests or Have chimney inspected for creosote and cleaned by a
leaves in termination cap
certified chimney sweep.
Down draft or negative pressure
Competition with exhaust devices
Do not use exhaust fans during start-up (refer to negative
pressure section).
Open window below the fireplace towards the wind.
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mix in less seasoned wood after fire is established (refer to
wood fuel section).
No glass doors
Add glass doors to slow down air flow.
Overdrafting
Check for correct vent height; too much vertical height
creates overdrafting.
Check location of vent termination (refer to chimney
assembly section).
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
13
Installer Guide
5
Getting Started
A. Typical Fireplace System
Termination cap
(Sections 8.I., 9.D.)
Additional lateral
support for chimney
above roof (or enclosed
in chase) if needed
(Section 8.A.)
Non-combustible
roof flashing maintains
minimum clearance
around chimney
Support straps
on rafter supports
chimney (not shown)
Storm Collar
(Section 9.D.)
Chimney penetrates roof
preferably without affecting
roof rafters (Section 8.H.)
Offset/Return (with hanger straps)
(Section 8.B.)
Attic insulation shield (not shown) must
be used here to keep insulation away
from chimney if attic is insulated
(Section 8.E.)
Ceiling firestop
on floor of attic
(Section 8.D.)
Chimney system
(Section 8)
Transition
Framing headed off
in ceiling joists (Section 8.D.)
Combustible
framing/header
on top of
V-shaped
standoffs
(spacers)
(Section 6.D.)
Enclosed space above
and around fireplace (Section 6.B.)
Mantel and surround (Section 12.E.)
Decorative facing
and trim (Sections 12.E., 12.F.)
Hearth extension
(Sections 12.C., 12.D.)
Outside Air
(both sides)
Figure 5.1
14
Protective metal
hearth strip(s) (Section 7.C.)
Factory-built fireplace
Typical Fireplace System
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
B. Design and Installation Considerations
D. Negative Pressure
NOTICE: Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building inspector, fire
officials or authorities having jurisdiction over restrictions,
installation inspection and permits.
WARNING! Risk of Asphyxiation! Negative pressure can
cause spillage of combustion fumes and soot. Fire must
draft properly for safe operation.
Before installing, determine the following:
Causes include:
•
•
•
•
•
•
•
•
Where the fireplace is to be installed.
The vent system configuration to be used.
Gas supply piping.
Framing and finishing details.
Whether optional accessories are desired.
Negative pressure results from the imbalance of air available for the fireplace to operate properly. It can be strongest in lower levels of the house.
Exhaust fans (kitchen, bath, etc.)
Range hoods
Combustion air requirements for furnaces, water heaters
and other combustion appliances
Clothes dryers
Location of return-air vents to furnace or air conditioning
Imbalances of the HVAC air handling system
Upper level air leaks such as:
- Recessed lighting
- Attic hatch
- Duct leaks
C. Draft
•
•
•
•
Draft is the pressure difference needed to vent fireplaces
successfully. When a fireplace is drafting successfully, all
combustion by-products are exiting the home through the
chimney.
To minimize the effects of negative air pressure:
Considerations for successful draft include:
•
•
•
•
Preventing negative pressure
Location of fireplace and chimney
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of the fireplace
system caused by:
• Inadequate draft due to environmental conditions
• Downdrafts
• Tight sealing construction of the structure
• Mechanical exhausting devices
• Improper positioning of the chimney in a not-recommended
location on the roof.
•
•
•
•
•
Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the fireplace
Avoid installing the fireplace near doors, walkways or small
isolated spaces
Recessed lighting should be a “sealed can” design
Attic hatches weather stripped or sealed
Attic mounted duct work and air handler joints and seams
taped or sealed
Basement installations should be avoided
NOTICE: The fireplace provides some outside air for
combustion. Other methods may be necessary if more air
is required.
NOTICE: Hearth & Home Technologies Inc. recommends the
use of direct vent appliances in basements.
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
15
E. Locating your Fireplace & Chimney
Location of the fireplace and chimney will affect performance.
•
Install within the warm air space enclosed by the building
envelope. This helps to produce more draft, especially
during lighting and die-down of the fire.
• Penetrate the highest part of the roof. This minimizes the
effects of wind loading.
• Locate termination cap away from trees, adjacent
structures, uneven roof lines and other obstructions.
• Minimize the use of chimney offsets.
• Consider the fireplace location relative to floor and ceiling
and attic joists.
• Take into consideration the termination requirements in
Section 8 and Section 9.
NOTICE: Locating the fireplace in an area of considerable
air movement can cause intermittent smoke spillage from
fireplace. Do not locate fireplace near
• frequently open doors
• central heat outlets or returns
DO NOT install in a basement.
Recommended Location:
• Above peak
Recommended Location:
• Above peak
• Inside heated space
Marginal Location:
• Below peak
Marginal Location:
• Wind loading possible
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Recommended:
• Insulated exterior chase
in cooler climates
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Windward
Leeward
Multi-level Roofs
Figure 5.1
16
Recommended Chimney Locations
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
F. Tools and Supplies Needed
H. Inspect Fireplace and Components
Before beginning the installation be sure the following tools
and building supplies are available:
WARNING! Risk of Fire and/or Explosion! Damaged
parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep fireplace
dry.
Reciprocating saw
Framing material
Pliers
Non-combustible sealant
Hammer
Gloves
Phillips screwdriver
Framing square
Flat blade screwdriver
Electric drill and bits
Plumb line
Safety glasses
Level
Tape measure
1/2-3/4 in. length, #6 or #8 self-drilling screws
Misc. screws and nails
•
•
•
•
•
•
Remove fireplace from pallet.
Remove fireplace and components from packaging and
inspect for damage.
Remove the transition, hearth molded brick panel, screens
and grate from inside the unit.
Vent system components, doors, remaining molded brick
panels and mortar are shipped in separate packages.
Report to your dealer any parts damaged in shipment.
Read all the instructions before starting the installation.
Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
G. Typical Fireplace Components
•
•
•
•
Hearth Molded brick panel
- Molded brick panel kit must be installed, but is sold
separately
Grate Assembly
Transition Assembly (14-11 in.)
- Must be installed immediately on top of the fireplace
Outside Air Kits
- Duct must be installed, but sold separately
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
17
6
Framing & Clearances
A. Select Fireplace Location
F
)))))
)
))
))))))
)
B
A
))
))
B
G
)))
))
))))
))
E
)))))
Note: In addition to these
framing dimensions, also
reference the following
sections:
• Clearances (6.B.)
• Framing (6.D.)
• Mantel Projections
(6.C)
• Fireplace Dimensions
(14.A.)
In an exterior chase
or projecting into a
garage
24 in. (610 mm)
from fireplace opening to
any perpendicular wall
Across a
corner
C
)))))
) ))
)))
D
G
As a
room
divider
Note: 1-1/2 in. min. air space
from fireplace to
combustible materials.
1/2 in. min. air space at
nailing flanges.
Along a wall
B
A
84 in.
(2134 mm)
5/8 in. (16 mm) all
configurations
))
))
G
))))))))))))))))
))))
))
))))))))))))))))))
))))))))))))))))))))
B
48 in.
(1219 mm)
MINIMUM
Model #
BIR42
Figure 6.1
A
B
C
D
E
F
G
in.
77 7/8
53 7/8
95 1/4
47 5/8
22 1/2
67 3/8
28 3/8
mm
1978
1368
2419
1210
572
1711
721
Fireplace Locations
NOTICE: Both outside air kits MUST be
installed.
18
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
B. Clearances
WARNING! Risk of Fire! You must comply with all minimum air space clearances to combustibles as specified in Figure 6.2. DO NOT pack required air spaces with insulation or other materials.
Storm Collar
Roof Flashing
of)
(ro
Shaded areas
represent
2 in. (51 mm) min.
air space clearance
required around pipe
(attic)
Attic
Insulation
Shield
(insulation)
(ceiling)
Offset/Return (secured
with hanger straps)
2 in. (51 mm) min.
(ceiling)
Ceiling Firestop
Must have 2 in. (51 mm)
minimum clearance
to header
Combustible Object
Transition
Figure 6.2
48 in.
1219 mm
0 in.
to floor
1-1/2 in. (38 mm) to back &
sides of appliance
(except at nailing flanges
where it is 1/2 in. [13 mm])
Air Space Clearances
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
19
C. Sidewalls/Surrounds
•
•
Locate adjacent combustible sidewalls a minimum of 24 in. (610 mm) from fireplace opening.
Mantle leg, surround, stub wall, whether combustible or noncombustible, may be constructed as shown in Figure 6.3.
Note: Grid depicts 1 inch squares.
FLUSH
FRONT
BRICK
FRONT
4 in.
[102 mm]
42 in.
[1067 mm]
50
°a
ng
le
22 3/8 in.
[568 mm]
39
°a
ng
le
52-7/8 in.
(1343 mm)
19 3/4 in.
[500 mm]
18 1/2 in.
[470 mm]
24 in.
[610 mm]
24 in.
[610 mm]
Figure 6.3
Mantel Leg, Surround or Wall Projection (acceptable on both sides of opening)
D. Frame the Fireplace
Figure 6.4 shows typical framing using combustible materials (2x4 lumber shown).
•
Observe all required air space clearances to combustible materials as shown in Figure 6.2.
2 in. (51 mm)
min. air space
clearance
from chimney.
Note: Framing must be
extended straight up,
all the way to the ceiling.
Header MUST NOT be notched!
C
D
D = extra space needed for outside air connection.
If outside air duct has no bend, this dimension may be
reduced as long as minimum clearances are met.
A
B
D
Model #
BIR42
A
B*
C **
D
in.
53 7/8
28 3/8
74 1/2
12
mm
1368
721
1892
305
* If interior of chase will be drywalled, add the thickness to this meaurement.
** Adjust header height for raised floor under fireplace.
Figure 6.4
20
Framing the Fireplace
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
7
Installation of Fireplace
CAUTION! Risk of Cuts/Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
A. Things to Consider
•
•
Location(s) of outside air kit(s)
Gas line piping
B. Position the Fireplace
•
•
Place the fireplace on a continuous flat surface.
Follow framing instructions in Section 6.
WARNING! Risk of Fire! Prevent contact with sagging,
loose insulation.
1 in. (25 mm) overlap
Minimum
• DO NOT install against vapor barriers or exposed
insulation.
• Secure insulation and vapor barriers.
• Provide minimum air space clearances at the sides
and back of the fireplace assembly as outlined in
Section 6.
C. Place Protective Metal Hearth Strips
Metal strips are placed 2 in. (51 mm)
under the front of the fireplace and must
extend beyond the front and sides of
fireplace opening by 2 in. (51 mm).
Figure 7.1
WARNING! Risk of Fire! Metal hearth strips MUST be
installed. DO NOT cover metal strips with combustible
materials. Sparks or embers may ignite flooring.
•
•
•
•
•
•
Refer to Figures 7.1 and 7.2.
Locate the two metal hearth strips measuring approximately
26 in. x 4 in. (660 mm x 102 mm) included with this
fireplace.
Slide each metal strip 2 in. (51 mm) under front edge of
fireplace.
Overlap strips in the middle of fireplace opening by 1 in
(25 mm) minimum..
Metal strips must extend beyond the front and sides of the
fireplace opening by at least 2 in. (51 mm).
Protect the front of a platform elevated above the hearth
extension with metal strips (not included with fireplace)
per Figure 7.2. See Section 12 for hearth extension
Position the Protective Metal Hearth Strips
Top piece must overlap
bottom piece
Raised Platform
2 in.
(51 mm)
1 in. (25 mm) min.
overlap
Floor
2 in.
(51 mm)
Figure 7.2
Protect the Front of an Elevated Platform
D. Level Fireplace
•
•
•
•
Level fireplace side-to-side and front-to-back.
Shim with non-combustible material as necessary.
Secure fireplace to framing with nailing flanges with a
minimum of two fasteners per nailing flange.
Check fireplace opening for square to ensure proper fit of
glass doors. Measure diagonals of fireplace opening to
make sure they are equal.
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
21
3 ft min. from
top of uppermost
chimney section
to air inlet.
Outside air installed
on both sides (right
side not shown)
Figure 7.3
Outside Air Inlet Locations
NO
NO
Outlet blocked by
snow, leaves, etc.
Garage or
combustible
liquids storage
NO
Attic space
NO
Outlet placed
higher than 3 ft
below the
termination cap
YES
Clear area
outside
house or in
ventilated
crawl space
Figure 7.4
22
Factory-built
fireplace
Outside Air Placement
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
E. Install Outside Air Kit
•
•
Keep duct runs short and straight to minimize
restriction.
The outside air kits must be installed on both sides of the
fireplace.
Flexible Duct
(not supplied)
WARNING! Outside air kits must be installed on both
sides of the fireplace to prevent overheating and fire.
•
•
•
•
•
Locate the outside air hoods in a clear area.
Install as shown in Figures 7.3, 7.4 and 7.5.
The air ducts may be run vertically.
The outside air hoods must be at least 3 ft (.91 m) below
the top of the uppermost chimney section.
The outside air hoods can be painted to match/accent the
color of the structure.
Outside Air
Hood
Figure 7.5
2 Wire Ties
Outside Air Installation
CAUTION! Risk of Fire or Asphyxiation! Do not draw
outside combustion air from wall, floor or ceiling cavity,
or enclosed spaces such as an attic or garage.
• DO NOT place outside air hood close to exhaust
vents or chimneys. Fumes or odor could be drawn
into the room through the fireplace.
• Locate outside air hood to prevent blockage from
leaves, snow/ice, or other debris. Blockages could
cause the unit to overheat.
NOTICE: The fireplace provides some outside air for
combustion. Other methods may be necessary if more air
is required.
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
23
8
Chimney Assembly
NOTICE: Chimney performance may vary.
• Trees, buildings, roof lines and wind conditions affect
performance.
• Chimney height may need adjustment if smoking or
overdraft occurs.
Chimney must extend
beyond combustible
roof structure
Maintain minimum
height of chimney
above roof
Install roof flashing
according to minimum
requirements
Offsets/returns
may not exceed
30° from vertical
Lock chimney
sections together
firmly to resist
movement
Termination Cap
Additional
support for
tall chimneys
Storm Collar
Maintain minimum
clearances to
combustibles as
specified
Support straps for offsets
(not shown) must be
secured to adequate framing
Offsets/returns must be
secured with the screws
provided (outer pipe only)
Attic shield not shown
(see Figure 6.2)
Ceiling firestops
are required where
chimney passes
through ceiling or
floor
Figure 8.1 Typical Chimney System - Guidelines for Chimney System Installation
24
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
A. Chimney Requirements
Measure vertical distances from the base of the fireplace
as shown in Figure 8.2.
• Minimum overall straight height
18 ft
(5.5 m)
18.5 ft
(5.64 m)
• Maximum height
90 ft
(27.43 m)
• Maximum chimney length between an offset
and return
20 ft
(6.1 m)
• Maximum distance between chimney
stabilizers
35 ft
(10.67 m)
• Maximum unsupported chimney length
between the offset and return
6 ft
(1.83 m)
• Maximum unsupported chimney height above
the fireplace
35 ft
(10.67 m)
• Maximum unsupported chimney above roof
6 ft
(1.83 m)
• Minimum height with offset/return
WARNING! Risk of Fire! You must maintain 2 in. (51 mm)
air space clearance to insulation and other combustible
materials around the chimney system. Failure to do so may
cause overheating and fire.
Determine the chimney components needed to complete
your particular installation:
•
•
•
•
Measure the total vertical height of the fireplace installation
from the base of the fireplace assembly to the approximate
location of the bottom of the termination cap.
Subtract the effective height of the fireplace assembly (see
Figure 8.2) from the total vertical height to determine the
overall height of the chimney installation.
Create a schematic for your application similar to Figure
8.2 showing components required (referring to Table 8.1).
Figure 8.1 identifies those components and where used.
Install a ceiling firestop whenever the chimney penetrates
a floor/ceiling.
NOTICE: A maximum of one offset and return may be
used.
CAUTION! Risk of Fire and/or Asphyxiation! DO NOT
connect this fireplace to a chimney flue servicing another
appliance. Do NOT connect to any air distribution duct
or system. These actions could cause overheating/fire
in the chimney flue, or release of exhaust fumes into the
living areas.
Table 8.1
HEIGHT OF CHIMNEY COMPONENTS
in.
mm
4-3/4
121
FS538
0
0
FS540
0
0
18
457
Chimney Stabilizer
SL11
6 ft (1.83 m) max.
unsupported chimney
above roof
Ceiling Firestops
Offsets/Returns
SL1130
Roof Flashing
RF570
0
0
RF571
0
0
SL1106
4-3/4
121
SL1112
10-3/4
273
SL1118
16-3/4
425
SL1136
34-3/4
883
SL1148
46-3/4
1187
Chimney Sections*
* Dimensions reflect effective height.
20 ft (6.10 m) max.
pipe between an
offset & return
Ceiling firestop
35 ft (10.7 m)
max. straight
unsupported
chimney height
14-11
Transition
97 1/2 in.
(2477 mm)
Effective
Height
Figure 8.2
18.5 ft (5.64 m)
min. height
single offset-return
90 ft (27.4 m)
max. height
Chimney Requirements
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
25
B. Using Offsets/Returns
•
•
Use an offset/return to bypass overhead obstructions.
An offset and return can be used as a single entity or separated by chimney section(s).
WARNING! Risk of Fire! DO NOT use offset/returns greater than 30°. Chimney draft will be restricted and could cause
overheating and fire.
•
•
•
•
Measure the shift needed to avoid the overhead obstruction. Refer to dimension A in Figure 8.3.
Find the appropriate A dimension listed in Table 8.2.
The B dimension coinciding with the A dimension measurement in Table 8.2 represents the required vertical clearance
needed to complete the offset/return.
Read across the chart to find the number of chimney sections/model numbers needed between the offset and return.
Example:
A
Your “A” dimension from Figure 8.3 is 14 1/2 in. (368
mm). Using Table 8.2 the dimension closest to, but not
less than 14 1/2 in. (368 mm) is 15 3/4 in. (400 mm) using
a 30° offset/return.
B
You determined from the table that you would need
36 5/8 in. (930 mm) (Dimension “B”) between the offset
and return.
The chimney component that best fits your application is
two SL1112s.
1-1/4 in. (32 mm)
OVERLAP
Figure 8.3
Chimney Offset/Return
Table 8.2
A
B
in.
mm
in.
mm
SL1106 SL1112 SL1118 SL1136 SL1148
4 7/8
124
17 7/8
454
-
-
-
-
7 1/4
184
22
559
1
-
-
-
-
9 3/4
248
26 1/8
664
2
-
-
-
-
10 1/4
260
27 1/4
692
-
1
-
-
-
12 3/4
324
31 3/8
797
1
1
-
-
-
13 1/4
337
32 3/8
822
-
-
1
-
-
15 3/4
400
36 5/8
930
-
2
-
-
-
18 1/8
460
40 3/4
1035
1
2
-
-
-
18 3/4
476
41 3/4
1060
-
1
1
-
-
21 3/4
552
47
1194
-
-
2
-
-
22 1/4
565
48
1219
-
-
-
1
-
24 3/4
629
52 1/8
1324
1
-
-
1
-
27 3/4
705
57 3/8
1457
-
1
-
1
-
28 1/4
718
58 3/8
1483
-
-
-
-
1
30 3/4
781
62 1/2
1588
1
-
-
-
1
33 3/4
857
67 3/4
1721
-
1
-
-
1
-
36 3/4
933
73
1854
-
-
1
-
1
39 3/4
1010
78 1/8
1984
-
-
-
2
-
41 1/8
1045
82 3/8
2092
1
-
-
2
-
45 3/4
1162
88 1/2
2248
-
-
-
1
1
48 1/8
1222
92 3/4
2356
1
-
-
1
1
51 3/4
1314
98 7/8
2511
-
-
-
-
2
Proper assembly of air cooled chimney parts results in an overlap of chimney joints
of 1-1/4 in. (32 mm). Effective length is built into this table.
26
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
C. Assemble Chimney Sections
WARNING! Risk of Fire! DO NOT install substitute or damaged chimney components.
• Use only those components described in this manual.
Substitute or damaged chimney components could impair
safe operation and cause overheating and fire.
•
•
•
•
•
•
Support the pipe during construction and check to be sure
inadvertent loading has not dislodged the chimney section
from the fireplace or at any chimney joint.
Attach a straight chimney section or an offset to the top
of the fireplace.
Place inner flue to the inside of the chimney section below
it. Place the outer casing outside the outer casing of the
chimney section below it. Refer to Figure 8.4.
Figure 8.4
Assembling Chimney Sections
NOTICE: Chimney sections cannot be disassembled once
locked together. Plan ahead!
Lock chimney sections and/or offsets/returns together by
pushing downward until the top section meets the stop
bead on the lower section.
Pull on the top section to make sure it is fully engaged
and will not separate.
You may use #6 or #8 sheet metal screws no longer than
1/2 in. (13 mm) to fasten chimney sections together. Do
NOT penetrate inner flue.
WARNING! Risk of Fire! You MUST use screws (provided) to fasten offset/returns to chimney sections to
keep the chimney parts from twisting. Failure to do so
could cause fire.
•
•
•
Fasten offset/returns to chimney sections. Insert the
screws (provided) through the predrilled holes. Do NOT
penetrate inner flue.
Secure chimney returns with hanger straps (provided);
fasten to studs or joists.
Vertical straight runs of chimney must be supported every
35 ft (10.7 m).
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
27
D. Install Ceiling Firestops
CAUTION! Risk of Fire! Ceiling firestops must be used
whenever the chimney penetrates a ceiling/floor.
• Chase construction requires ceiling firestops at each floor
or every 10 ft (3.05 m) of clear space.
• The ceiling firestop slows spread of fire and reduces cold
air infiltration.
•
•
•
•
•
Install a ceiling firestop whenever chimney penetrates
ceiling/floor.
Mark and cut an opening in ceiling as shown in
Figure 8.5.
Frame the opening with the same size lumber used in the
ceiling joists.
Nail the ceiling firestop to the bottom of the ceiling joists
when there is a room above/
Use an attic insulation shield if the ceiling is insulated. The
ceiling firestop may then be attached above or below the
joists. Refer to Figure 8.6 and 8.7.
WARNING! Risk of Fire! DO NOT seal area between
firestop opening and chimney pipe except where they
enter the attic or leave the warm-air envelope of the
home (use 600° F sealant).
ROOM ABOVE (non-insulated ceiling)
B
A
Ceilng firestop from
bottom
ATTIC ABOVE (insulated ceiling)
Ceiling firestop from
top
Note: Use same dimensional lumber for framing
ceiling firestop and joists.
A
Catalog #
in.
mm
in.
mm
FS538
17
432
17
432
FS540
17
432
26
660
Figure 8.5
28
B
Installing the Ceiling Firestop
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
E. Install Attic Insulation Shield
WARNING! Risk of Fire! You MUST install an attic insulation shield when there is any possibility of insulation
or other combustible material coming into contact with
the chimney.
Bend remaining tabs
to rest against pipe to
prevent insulation
from falling in.
Bend inward
90°
Insert three
screws
• DO NOT pack insulation between the chimney and
the attic insulation shield.
• Failure to keep insulation and other materials away
from chimney pipe could cause fire.
• DO NOT offset chimney inside insulation shield.
Installation of a ceiling firestop is required
•
Refer to Figures 8.6 - 8.8.
•
Roll the shield around the chimney (if chimney is already
installed) until you have a 3 in. (76 mm) overlap and the
three holes on each side match up (large holes on top).
Insert three screws into the matching holes to form a
tube.
Bend three tabs on the bottom of the tube inward to 90°
to maintain chimney air space as shown in Figure 8.6.
Rest the insulation shield on the ceiling firestop below.
Bend the three short tabs at the top of the shield inward
to 90° to maintain the 2 in. (51 mm) air space from the
chimney.
Bend the remaining top tabs to just meet the pipe.
•
•
•
•
•
3 in. (76 mm)
overlap
Figure 8.6
Prepare Attic Insulation Shield
Pipe
Tabs bent in to
rest against pipe
Attic Insulation Shield
6 Tabs bent
in 90°
17 in. (432 mm)
diameter
Ceiling Firestop
If you wish to make a custom shield or barrier, follow these
guidelines:
•
Metal is preferred, although any material stiff enough to
hold back the insulation can be used.
WARNING! Risk of Fire! Use of cardboard or other
materials that can deflect under humidity or other environmental conditions is not recommended.
•
•
•
•
Pipe
Insulation
Insulation
13 in.
(330 mm)
Figure 8.7
Install Attic Insulation Shield Above the Ceiling
The shield or barrier must be tall enough to extend above
the insulation and prevent blown-in insulation from spilling
into the cavity.
The shield should be affixed to building structure.
Maintain specified air spaces around chimney.
Check instructions and local codes for further details.
Tabs bent in to
rest against pipe
Pipe
Attic Insulation Shield
17 in. (432 mm)
diameter
6 Tabs bent
in 90°
Insulation
13 in.
(330 mm)
Figure 8.8
Insulation
Pipe
Ceiling Firestop
Install Attic Insulation Shield Below the Ceiling
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
29
F. Cut Out Hole in Roof
•
•
•
•
•
•
•
Refer to Figure 8.9.
Plumb from roof to center of chimney.
Drive a nail up through roof to mark center of pipe.
Measure to either side of nail and mark the 17 in. x 17 in.
(432 mm x 432 mm) opening required.
Measure opening on the horizontal; actual length may be
larger depending on roof pitch.
Cut out and frame opening.
Refer to Chapter 25 of the Uniform Building Code for
roof framing details.
G. Complete Installation
WARNING! Risk of Fire! You MUST maintain 2 in.
(51 mm) air space to insulation and other combustible materials around the chimney system. Failure to do so could
cause overheating and fire.
• Keep chimney sections from separating or twisting.
• You may secure straight chimney sections at the joints
with screws no longer than 1/2 in. (13 mm).
H. Install Flashing
•
•
Slip the flashing over the chimney.
Nail the flashing to the roof. Keep gaps between flashing
plate and roof to a minimum.
NOTICE: Roofing shingles must be below the flashing
plate on the lower side of a sloped roof and over the
flashing plate on the sides and top.
•
Caulk the flashing plate and roof junction as well as the
vertical seam on the flashing. All nail heads must be
caulked with a roofing sealant.
Figure 8.9
30
Ceiling/Attic Construction
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
I. Chimney Termination Requirements
•
•
•
•
•
Install a cap approved and listed for this fireplace system.
Locate cap where it will not become plugged by snow or other materials.
Locate cap away from trees or other structures.
The bottom of the termination cap must be at least 3 ft (.91 m) above the roof AND at least 2 ft (.61 m) above any portion
of roof within 10 ft (3.05 m) as shown in Figure 8.10.
See below for distance required between caps.
Slanted Roofs
Chimney must extend 2 ft (.6 m)
above any portion of the roof or
adjacent structures within
10 ft (3 m) of the chimney
Chimney must
extend 3 ft (.9 m)
above the roof
Flat Roofs
Chimney must extend 2 ft (.6 m)
above any portion of the roof or
adjacent structures within
10 ft (3 m) of the chimney
Chimney must
extend 3 ft (.9 m)
above the roof
Multiple Chimney Locations
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
B
A*
Wood
Minimum
(See
illustration
above)
Perpendicular Wall
Gas, Wood or Fuel Oil
Termination Cap
Gas
Termination
Cap **
*
**
Î
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood terminations, the
wood termination cap must be higher than the gas termination cap.
Figure 8.10 Multiple Chimney Locations
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
31
9
Chase Installations
A. Construct the Chase
A chase is a vertical boxlike structure built to enclose the
fireplace and/or its vent system. Vertical chimneys that
run on the outside of a building must be installed inside a
chase.
Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST
be checked.
A chase should be constructed in the manner of all outside
walls of the home to prevent cold air drafting problems. The
chase should not break the outside building envelope in
any manner. All outer walls need to be insulated.
Gas line holes and other openings should be caulked with
high temperature caulk or stuffed with unfaced fiberglass
insulation. If the fireplace is being installed on a cement
slab, we recommend that in cold climates, a sheet of
plywood or other raised platform be placed underneath to
prevent conducting cold up into the room.
Three examples of chase applications are shown in Figure 9.2.
1. Fireplace and chimney enclosed in an exterior chase.
2. Chimney offset through exterior wall and enclosed in chase.
3. Chase constructed on roof.
Note: In cooler climates, all chase walls should be insulated.
Building codes require false ceiling and ceiling firestops
at each floor of the chase or every 10 ft (3.05 m) of clear
space to control spread of fire.
Walls, ceiling, base plate and cantilever floor at the first
level of the chase should be insulated. See Figure 9.1.
Vapor and air infiltration barriers should be installed in the
chase as per regional codes for the rest of the home. Additionally, Hearth & Home Technologies recommends that the
inside surfaces be sheet rocked and taped (or the use of an
equivalent method) for maximum air tightness.
1
Figure 9.2
Round Termination Cap
Metal Chase Top
2
3
Chase Constructions
WARNING! You must install false ceilings and ceiling firestops at each floor of the chase or every 10 ft (3.05 m) to
control spread of fire.
Ceiling
Firestop
WARNING! Risk of Fire! DO NOT seal area between
firestop opening and chimney pipe except where they enter
the attic or leave the warm-air envelope of the home (use
600° F sealant).
False Ceiling
Tabs
Attic
Insulation
Shield
Insulation in the
outside walls
of the chase
Insulation
False Ceiling
Insulation
WARNING! Risk of Fire! You must maintain a minimum
2 in. (51 mm) air space clearance to insulation and other
materials surrounding the chimney system.
• Insulation and other materials must be firmly secured to
prevent accidental contact with chimney system.
• Failure to prevent contact between insulation or other
materials and chimney system may cause overheating
and fire.
False Ceiling
Chimney
Ceiling
Firestop
Figure 9.1
32
Chase Assembly
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
B. Install Fireplace & Chimney
Slope Downward
(1/4 in. per foot
minimum)
Install as per Sections 7 and 8.
C. Install Chase Top
•
•
•
•
•
2 in. (51 mm) Collar
on Chase Top
You MUST use a chase top in a chase installation. Chase
tops are available from your Heatilator dealer or may be
field constructed.
Include a turndown and drip edge to prevent water from
seeping into the chase.
Include a 2 in. (51 mm) soldered, caulked or spun collar
around pipe opening to keep water out.
Provide a 1/8 in. (3 mm) gap around the flue pipe.
Slope the chase top downward away from the opening.
Turn-down
Drip Edge
Chase
.018 (26 ga) min.
Galvanized
Chase Top
CAUTION! DO NOT caulk the pipe to the chase top collar.
•
•
Caulk all seams to prevent leaks.
Refer to Figure 9.3.
Figure 9.3
Chase Top Construction
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
33
D. Install Termination Cap
•
Install the chimney sections up through the chase enclosure.
•
Assemble
storm collar
around extended
termination cap
pipe
once cap is
installed.
Install termination caps following instructions provided
with them.
WARNING! Risk of Fire! The minimum overlap of cap
to pipe (as shown in the following illustrations) MUST
be met or chimney may separate from cap. Separation
allows sparks, heat and embers to escape.
Caulk gaps between
storm collar & pipe,
and storm collar
& chase top.
NOTICE: The termination cap can be painted with a rustresistant paint to protect against the effects of corrosion
on those parts exposed to the weather.
•
TR11T Round Telescoping Termination Cap
Termination
Cap
Do NOT
block air
holes
Storm
Collar
3 clip brackets.
Slip over chase collar
and attach with screws
provided.
Collar
2 in. (51 mm)
Minimum Height
14 1/2 in. (368 mm)
Maximum
Chase Top
TR11, TR11-TV Round Termination Cap
Termination
Cap
Chase
Slip
storm collar
around chimney pipe
before termination
cap pipe is snapped
into the chimney
pipe.
Caulk gaps between
storm collar & pipe,
and storm collar
& chase top.
Collar
2 in. (51 mm)
Minimum Height
Chimney
Pipe
Do NOT
block air holes
Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)
6 in. (153 mm)
Minimum top of
chase to top of
chimney pipe
Storm
Collar
Chimney
Pipe
Figure 9.5
•
Installing a TR11T Round Telescoping Termination Cap
ST1175 Square Termination Cap
Chase Top
Place waterproof
caulk or sealer under
each flange of the
termination cap and
on top of each screw
to help prevent leaks.
Chase
Termination Cap
Collar
2 in. (51 mm)
Minimum Height
Termination cap pipe and chimney section must be snapped
together to maintain an overlap of 1-1/2 in. (38 mm).
Figure 9.4
Flange
4 3/4 in. (121 mm)
Maximum
top of chase to
top of
chimney section
Chase Top
Installing a TR11 & TR11-TV Round Termination Cap
Chase
Chimney
Pipe
Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)
Figure 9.6
34
Installing an ST1175 Square Termination Cap
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
•
TCT1175 Terra Cotta Cap
Place waterproof
sealer under each
flange of the termination cap and on top of
each screw to help
prevent leaks.
Termination Cap
The last section of pipe
must stop between 2 in.
(51 mm) above top of
chase and 7 in. (178
mm) below top of chase
Collar
2 in. (51 mm)
Minimum Height
Chase Top
2 in. (51 mm)
7 in. (178 mm)
Chase
Chimney
Pipe
Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)
Figure 9.7
Installing a TCT1175 Terra Cotta Cap
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
35
10
Shrouds
A. Radiation Shield
•
Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap
Some shrouds require a radiation shield. Use where
specified.
B. Field Constructed Shrouds
WARNING! Risk of Fire! Shrouds must be constructed as
specified. Improper construction may overheat chase top.
•
•
•
•
Length x Width to fit inside shroud
Chase top shrouds may be field constructed where
permitted by regional building codes.
NOTICE: Some regional codes require an agency-Listed
shroud. Consult your local building officials.
•
3 in. (76 mm) tall legs
Figure 10.1 Radiation Shield
Hearth & Home Technologies Inc. supplies UL listed
shrouds. See your dealer for details.
Different shroud designs have been tested for Hearth
Technologies fireplace systems using the TR11 and TR11T
termination caps.
The shrouds must be constructed from a minimum .018
in. (26 ga) thick aluminized steel.
The wire mesh is optional but recommended and must be
.018 in. thick minimum with mesh no larger than 1/2 in.
(13 mm).
Open Top Shroud (TR342 & TR11/TR11T caps require radiation shield)
TR11/11T
Min.
Top Dim.
Min. Base Dims.
in
Min.
Top Dim.
mm
3 in (76 mm)
minimum
Min.
Base Dim.
Min.
Base Dim.
26 x 26
813 x 813
660 x 660
Min. Top Dims.
in
29 x 29
23 x 23
mm
737 x 737
584 x 584
Min. Opening Width
in
26 x 26
20 x 20
mm
660 x 660
508 x 508
Figure 10.2 Open Top Shroud Dimensions
36
32 x 32
Radiation Shield
Required
Min. Opening
Width
Min. Opening
Width
TR11/11T TV
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
Mailbox Style Shroud (radiation shield required)
TR11/11T
TR11/11T TV
Min. Base Dims.
3 in. (76 mm)
Min. Opening Height
in
34 x 34
28 x 30
mm
864 x 864
711 x 762
Min. Height Above Radiation Shield
Min. Height
above radiation
shield
in
mm
Min. Base Dim
Min.
Base Dim
21-1/4
20-1/2
540
521
Min. Opening Width
Min. Opening Width
in
28 x 28
22 x 24
mm
711 x 711
559 x 610
3 in. (76 mm) Min.
Radiation Shield Height
from top of Chase
Figure 10.3 Mailbox Style Shroud Dimensions
Roofed Style Shroud (Radiation Shield Required)
TR11/11T
TR11/11T TV
Min. Base Dims.
Minimum
Height above
Radiation Shield
3 in. (76 mm)
Radiation
Shield Height
Termination
Cap
Radiation Shield
Minimum
Opening
Height
in
34 x 34
34 x 34
mm
864 x 864
864 x 864
Min. Height Above Radiation Shield
in
mm
16
406
406
Min. Opening Width
Minimum
Base Dimension
in
28
28
mm
711
711
Chase Top
Min. Base Dimen
sion
16
Min. Opening Height
Min. Opening Width
in
12
12
mm
305
305
Figure 10.4 Roofed Style Shroud Dimensions
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
37
11
Installation of Molded Brick Panel
A. Install Hearth Molded Brick Panel
•
Note: Use T-brackets as templates and drill pilot
holes into the inner shell with the drill bit provided.
Side panels must be installed first.
Place hearth panel into the fireplace.
B. Install Side Molded Brick Panel/Traditional
•
•
•
•
•
•
•
•
•
If a gas line is to be installed, remove the knockouts in
the inner firebox and in the outer shell on the side of
your choice. Refer to dimension drawings for location of
knockouts and Section 13.A. for gas provisions.
Do NOT remove screen rods.
Refer to Figure 11.1.
Install lower side panel, tapered edge to the front. Align
the front edge with the front of the column (or butted to
the surround if installed).
Install two T-brackets stem down into mortar line, do not
tighten.
Install upper side panel in the unit, tapered edge to
the front. Position the bottom of panel behind the Tbrackets.
Install two T-brackets stem up into mortar lines, one on
its side on the front edge, do not tighten.
Install two Z-brackets in the mortar lines across the top.
Tighten these and all previously installed brackets.
Install second side panel following the steps above.
C. Install Back Molded Brick Panel/Traditional
•
•
•
•
•
•
•
Refer to Figure 11.1.
Set the grate brackets in place, 26.5 in. (673 mm) center
to center.
Install the lower back panel. Center from side to side.
Install three T-brackets stem down into mortar line to hold
lower back in position. Do not tighten.
Install upper back panel. Position bottom of panel behind
the previously installed T-brackets.
Install two T-brackets stem side up into mortar line, do not
tighten
Install two Z-brackets in the mortar lines across the top.
Tighten these and all previously installed brackets.
Front
Upper Side
Molded Brick Panel
Upper Back
Molded Brick Panel
Right Side
Molded Brick Panel
removed for
clarity
Lower Side
Molded Brick Panel
Lower Back
Molded Brick Panel
Hearth Molded Brick Panel
Figure 11.1 Traditional Molded Brick Panel
38
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
D. Install Side Molded Brick Panel - Herringbone
•
•
•
•
•
•
•
•
•
If a gas line is to be installed, remove the knockouts in
the inner firebox and in the outer shell on the side of
your choice. Refer to dimension drawings for location of
knockouts and Section 13.A. for gas provisions.
Do NOT remove screen rods.
Refer to Figure 11.2.
Install lower side panel, tapered edge to the front. Align
the front edge with the front of the column (or butted to
the surround if installed).
Install two T-brackets stem down into mortar line, do not
tighten.
Install upper side panel in the unit, tapered edge to
the front. Position the bottom of panel behind the Tbrackets.
Install two T-brackets stem up into mortar lines, one Ybracket on the front edge as shown. Do not tighten.
Install two Z-brackets in the mortar lines across the top.
Tighten these and all previously installed brackets.
Install second side panel following the steps above.
Note: Use T-brackets as templates and drill pilot holes into
the inner shell with the drill bit provided. Side panels must
be installed first.
E. Install Back Molded Brick Panel - Herringbone
•
•
•
•
•
•
•
Refer to Figure 11.2.
Set the grate brackets in place, 26.5 in. (673 mm) center
to center.
Install the lower back panel. Center from side to side.
Install two T-brackets stem down into mortar line to hold
lower back in position. Do not tighten.
Install upper back panel. Position bottom of panel behind
the previously installed T-brackets.
Install three T-brackets stem side up into mortar line, do
not tighten
Install two Z-brackets in the mortar lines across the top.
Tighten these and all previously installed brackets.
Front
Upper Side
Molded Brick Panel
Upper Back
Molded Brick Panel
Lower Back
Molded Brick Panel
Lower Side
Molded Brick Panel
Grate Brackets
Hearth Molded Brick Panel
Figure 11.2 Herringbone Molded Brick Panel
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
39
F. Install Mortar
•
Note: We recommend mortar be applied after
facing materials are installed.
Tools Required:
•
•
Mortar bag
Drill
Trowel
3/32 drill bit (provided)
Mixing bucket
Phillips screwdriver
Sponge or spray bottle
Joint striker
•
Drill with mixing attachment (optional)
•
•
Bucket of water
The mortar material provided should be sufficient to complete the installation of the molded brick panels without
considerable waste.
NOTICE: Do not substitute for HHT mortar. Other materials
may stain the molded brick panels.
•
•
•
Mix approximately 1/3 of the mortar material with 1/2
gallon of water in the mixing bucket. Stir the mixture with
the mixing attachment and drill. The consistency should
allow the material to be squeezed from the mortar bag but
not too runny.
Fill the mortar bag with the prepared mixture.
Apply mortar by squeezing the material from the mortar
bag into the joint lines. If filling a vertical line, start from
the top and work down. Apply slowly. Mixture should be
flush or higher than the panel surface.
Mix more material as necessary to finish the job and then
let the unit set until firm, may take two hours or more.
Thoroughly clean the bag, tools and mixing bucket.
Use a joint striker and strike the material in the joints. The
excess material should fall off somewhat dry.
Sweep the loose material off the floor of the unit.
Final cleanup with sponge and water.
VERY IMPORTANT: Allow the mortar 72 hours to cure
before operating the fireplace.
Mortar should be applied
after finishing material is
installed. Mortar will be
applied between finishing
materials and molded
brick edges, bottom and
sides.
The noncombustible finishing
material across the top of
fireplace opening will be even
with lower edge of metal face.
Noncombustible finishing
materials MUST overlap
side faces by 1 1/4 in. (32 mm)
to cover the edges of the
panels. Finished opening
should be 38 x 42 in. (965 x
1067 mm) to allow for door
installation.
The seam between
finishing materials and
firebox top must be sealed
with non-combustible
sealant.
The surface of the finished hearth extension and
the surface of the hearth panel should be level.
Figure 11.3 Facing Materials and Mortar
•
•
•
•
•
Remove one screen rod by removing
one screw (near the center of the top
front). Pull rod out of the hole. Keep
the screw.
Lay one screen panel flat and slide the
round end of the rod through the rings
starting at the handle side of screen.
Leave the last ring off the rod.
Insert the rod through the hole in the
bracket. Slip the last ring over the rod
on the other side of the bracket.
Fasten the flat end of the screen rod
back in place using the screw removed
earlier.
Repeat for the other screen panel.
40
Round end of Rod through rings,
then into Screen Rod Clip
Top of Fireplace
Center of Fireplace Opening
G. Install Screens
Figure 11.4 Install Screens
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
Rod Screen
Clip
Inside
Firebox
12
Finishing
A. Non-Combustible Materials
•
•
Materials which will not ignite and burn, composed of any
combination of the following:
- Steel
- Iron
- Brick
- Tile
- Concrete
- Slate
- Glass
- Plasters
Materials reported as passing ASTM E 136, Standard
Test Method for Behavior of Metals, in a Vertical Tube
Furnace at 750° C
•
•
•
•
•
B. Combustible Materials
•
•
You MUST use a hearth extension with this fireplace.
This fireplace has been tested and approved for use with
a hearth extension insulated to a minimum R value of
2.32.
The hearth extension material MUST be covered with tile,
stone or other non-combustible material.
Manufactured hearth materials will usually have a published
R value (resistance to heat) or k value (conductivity of
heat). Refer to the formula in Table 12.1 to convert a k
value to an R value,
Refer to Table 12.2 for hearth extension insulation
alternatives.
Materials made of or surfaced with any of the following
materials:
- Wood
- Compressed paper
- Plant fibers - Plastic
Any material that can ignite and burn; flame proofed or
not, plastered or un-plastered
C. Hearth Extension
12 in.
(305 mm)
WARNING! Risk of fire! High temperatures, sparks, embers or other burning material falling from the fireplace may
ignite flooring or concealed combustible surfaces.
• Metal hearth strips MUST be installed (Section 7.C.).
• Hearth extensions MUST be installed exactly as
specified.
42 in.
(1067 mm)
12 in.
(305 mm)
66 in.
(1676 mm)
Raised Platform
20 in. (508 mm) Minimum
Flush Hearth
30 in. (762 mm) Minimum
Table 12.1
(R value of hearth must be
equal to or greater than 2.32)
R = 1/k x inches of thickness
Figure 12.1 Hearth Extension Dimensions
Table 12.2
Hearth Extension Insulation Alternatives-Total minimum R Value must equal 2.32
Material
Hearth & Home HX3, HX4 (Micore 300™)
k per inch
thick
R per inch
thick
Minimum thickness required
0.49
2.06
1 in. (25.4 mm)
USG Micore 160™
0.39
2.54
1 in.(25.4 mm)
USG Durock™ Cement Board
1.92
0.52
4 in. (101.6 mm)
Cement Mortar
5.0
0.20
10 in. (254 mm)
Common Brick
5.0
0.20
10 in. (254 mm)
Ceramic Tile
12.50
0.08
25-3/4 in. (654 mm)
Armstrong™ Privacy Guard Plus
0.46
2.18
1 in. (25.4 mm)
14.3 to 20.0
0.07 to 0.05
29-1/2 to 41 in. (749.3 to 1041.4 mm)
Marble
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
41
Raised Hearth Extension Framing
The hearth framing must be constructed of non-combustible materials (Figure 12.2) and placed on 1/2 in. Durock
and 1 in. Micore (or equivalent material) (Figure 12.4).
When creating the platform, allow for the thickness of the
non-combustible finishing materials (Figure 12.5).
IMPORTANT! Hearth extension design must be determined
before installation of fireplace.
Continuous,
non-combustible sealant
Tile, stone or other
non-combustible material
Fireplace
Durock
1 in. Micore or
equivalent insulation
(see Table)
*
Floor constructed of wood or
other combustible material
Protective
Metal Hearth
Strip
Noncombustible
Framing Material
1 in. Micore or
equivalent insulation
& 1/2 in. Durock
Figure 12.4 Raised Platform Hearth Extension-Framing Materials
*
* 2 in. (51 mm)
Figure 12.2 Hearth Extension Construction
Note: The bottom of the
fireplace opening is 3-3/4 in.
(95.3mm) above the bottom of
the fireplace. Finished hearth
must NOT extend above this
level.
Bottom of
fireplace opening
20 in. Min.
Hearth Extension
Platform must be built
to raise the bottom of
the fireplace opening
to the level of the
desired hearth height.
Noncombustible
Finishing Material
1 in. Micore or
equivalent insulation
& 1/2 in. Durock
Protective Metal
Hearth Strips
Noncombustible
Finishing Materials
Figure 12.5 Raised Platform Hearth Extension-Finishing Materials
Floor
Noncombustible
Framing Material
Figure 12.3 Raised Platform Hearth Extension Detail
42
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
Non-combustible Sealant
After completing the framing and applying the facing materials over the framing, a bead of non-combustible sealant
must be used to close off any gaps at the top and sides
between the fireplace and hearth.
Non-combustible Sealant
Figure 12.6 Place Non-combustible Sealant
Flush Hearth Extension Framing
•
•
Fireplace must be recessed 3 3/4 in. (95.3 mm) below the
finished floor.
Refer to Figures 12.7 and 12.8.
Note: The bottom of the fireplace
opening is 3-3/4 in. (95.3mm) above
the bottom of the fireplace. Finished
hearth must NOT extend above this
level.
Finished
Floor
Figure 12.7 Flush Hearth Extension
1 in. (25.4 mm)
Micore and
1/2 in. (13 mm)
Durock
Bottom of
Fireplace Opening
30 in. Min.
Hearth Extension
Noncombustible Finishing Material
Protective Metal
Hearth Strip
Figure 12.8 Flush Hearth Extension Side View
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
43
D. Finishing Material
Refer to Sections 12.A. and Sections 12.B. for combustible/noncombustible materials. Refer to Figure 12.10 for
noncombustible zone.
These surfaces
must be covered
with non-combustible
material.
WARNING! Risk of Fire! You must maintain clearances.
• Use only non-combustible framing material below
standoffs.
• Sheetrock, wood or other combustibles must NOT be used
as sheathing or facing in the noncombustible zone.
• DO NOT cover metal fireplace front with combustible
materials.
• Install combustible materials only to specified clearances
on top front and side edges.
•
•
•
•
Complete framing and apply facing material (drywall) over
framing.
A bead of 300-deg F minimum non-combustible sealant
must be used to close off any gaps at the top and sides
between the fireplace and facing to prevent cold air
leaks.
Large gaps can be bridged with fiberglass rope gasket.
Only non-combustible materials may be used to cover the
metal fireplace front.
Figure 12.9 Noncombustible Facing
Note: We recommend mortar be applied after
facing materials are installed. Refer to Section 11.F.
2 x 4 stud wall
Finished combustible wall
2 x 4 header, flush with
front of stand-offs
Combustible material
Non-combustible
decorative facing
(up to full brick depth)
Continuous,
non-combustible sealant
Tile, stone or other
non-combustible material
1 in. Micore
or equivilent
insulation &
1/2 in. Durock
Hearth
Refractory
Metal strips are placed 2 in. (51 mm)
under the front of the fireplace and must
extend beyond the front and sides of
fireplace opening by 2 in. (51 mm)
Bottom of fireplace opening
and finished hearth may be
the same height
Floor constructed of wood or
other combustible material
Figure 12.10 Decorative Facing
44
Non-combustible
sealant.
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
E. Combustible Mantel
•
•
•
•
•
•
•
See Figure 12.11.
A combustible mantel may be positioned no lower than 22 in. (508 mm) above the top of the fireplace opening.
A combustible mantel may have a maximum depth of 12 in. (305 mm).
Combustible trim and materials cannot be placed within 6 in. (152 mm) of the fireplace opening (top or sides).
Combustible materials projecting more than 1-1/2 in. (38 mm) shall not be placed within 12 in. (305 mm) from the top of
the fireplace opening.
Combustible trim must not cover the metal surfaces of the fireplace.
Mantel clearance is in accordance with Section 7-3.3.3 of ANSI/NFPA211.
7 ft (2134 mm)
minimum
floor to ceiling
Combustible Wall
Combustible Decorative Facing
2 x 4 stud header
Standoffs
12 in./305 mm MAXIMUM
Notches
22 in./559 mm MINIMUM
Noncombustible
Decorative Facing
Measured from top of fireplace opening
Seal joint with
non-combustible sealant
Î
Figure 12.11 Clearances to Mantels or other Combustibles above Fireplace
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
45
F. Mantel, Adding Extra Support
If extra support for the mantel is needed across the front of
the fireplace:
•
•
•
•
•
Secure to
framing
Obtain a piece of top/bottom track used in metal
framing.
Cut the track to 57 7/8 in. (1470 mm) long.
Notch each end of the track 2 in. (51 mm). See
Figure 12.12.
Place the track into the notches (shown in Figure 12.13)
on the front standoffs and secure to the framing on both
sides of the fireplace (Figure 12.14).
Use drywall screws to fasten the mantel to the metal
framing.
Notches
(both ends)
Figure 12.14 Secure to Framing
2 in.
(51 mm)
Figure12.12 Notch the Metal Track
Notches
in standoffs
Figure 12.13 Notch in Standoffs
46
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
G. Sidewalls/Surrounds
39
°a
ng
le
24 in.
[610 mm]
22 3/8 in.
[568 mm]
18 1/2 in.
[470 mm]
52-7/8 in.
(1343 mm)
42 in.
[1067 mm]
FLUSH
FRONT
24 in.
[610 mm]
19 3/4 in.
[500 mm]
4 in.
[102 mm]
BRICK
FRONT
Note: Grid depicts 1 inch squares.
•
Adjacent combustible sidewalls must be located a
minimum of 24 in. (305 mm) from the fireplace opening.
Combustible mantel legs, surrounds and stub walls may
be constructed per Figure 12.15.
50
°
a
ng
le
•
Figure 12.15 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
47
13
Accessories
A. Gas Log/Lighter Provision
WARNING! Fire and/or Asphyxiation Risk! Use with solid
wood fuel or decorative gas appliance only. Gas fire generates fumes.
• DO NOT install unvented gas logs
• Damper must be locked fully open when gas logs are
installed
A certified gas log lighter or decorative gas log set can be
installed in this fireplace.
•
•
•
•
•
•
•
•
•
Maximum input is 150,000 BTU/hr.
Decorative gas appliance must be certified to ANSI Z21.60
“Standard for Decorative Gas Appliances for Installation
in Vented Fireplaces”.
Must be installed in accordance with the National Fuel
Gas Code, ANSI Z223.1.
A gas log set must incorporate a gas shutoff.
Gas log set requires the damper to be locked fully open.
A listed automatic damper system with safety interlock may
be used in this fireplace with only compatible, listed gas log
sets. See damper system manufacturer’s instructions.
Knockouts are provided on both sides of the fireplace for
1/2 in. (13 mm) iron pipe.
A locating dimple (see Figure 13.2) is located on both sides
of the fireplace in the molded brick panels for drilling a 1
in. (25 mm) diameter hole for installation of a gas line.
After the panel is installed, drill the hole for the gas line.
Seal panel around pipe with fireplace mortar or a high
temperature, noncombustible sealant.
Outer Shell
of Fireplace
Firebox
Maintain air clearance
to combustibles.
Refractory
Combustible
Materials
Seal with
fireplace mortar
or non-combustible sealant
Gas Line
Repack
Insulation
Knockout
1 1/2 in. (38 mm)
air space around
pipe
Gas Line
4 in.
(102 mm)
Combustible materials
may be located at zero
clearance to gas line
beyond 4 in. (102 mm)
from fireplace side.
Figure 13.1 Gas Line Installation
Gas Line
Dimple
B. Wood Burning Inserts
WARNING! Risk of Fire! Improper installation of wood
inserts may cause fireplace or chimney system to overheat.
If a wood burning insert is being installed in this fireplace,
Hearth & Home Technologies recommends full reline of the
chimney.
•
•
Cooling air openings at the top of the chimney must not
be obstructed in any manner.
Hearth & Home Technologies recommends securing the
reline at the top of the flue and using the cap certified for
use with this fireplace system.
Gas Line
Dimple
Figure 13.2 Gas Line Dimples
48
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
14
Reference Materials
A. Fireplace Dimensions
37 1/8 in.
943 mm
11 in.
281 mm
27 1/2 in.
699 mm
74° TYP.
97 1/2in.
2477 mm
74 1/8 in.
1883 mm
70 3/4 in.
1797 mm
Gas Line
Knockout
5 in.
129 mm
16 1/8 in.
408 mm
Gas Line
Knockout
54 in.
1372 mm
6 7/8 in.
175 mm
11 1/8 in.
282 mm
38 in.
965 mm
42 in.
1067 mm
52 7/8 in.
1343 mm
3 3/4 in.
97 mm
6 7/8 in.
175 mm
5 in.
129 mm
11 1/8 in.
282 mm
16 1/8 in.
408 mm
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
49
B. Optional Components
66 in.
(1676 mm)
20 in.
(508 mm)
HX4 Hearth Extension
1/2 in.
(13 mm)
ID6 Insulated Duct
6 in. (152.4 mm) i.d.
DFG4042 Series Glass Doors
(optional)
DFS4042 Series Screen Doors
(optional)
42 in.
(1067 mm)
UD6 Uninsulated Duct
6 in. (152.4 mm) i.d.
42 in.
(1067 mm)
See your Heatilator dealer for a complete list of optional components.
50
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
C. Chimney Components
The following pictures show only those chimney components which may be safely used with this fireplace.
Catalog #
Description
A
SL1106
Chimney Section - 6 in. (152 mm) long
SL1112
Chimney Section - 12 in. (305 mm) long
SL1118
Chimney Section - 18 in. (457 mm) long
SL1136
Chimney Section - 36 in. (914 mm) long
SL1148
Chimney Section - 48 in. (1219 mm) long
SL11
Chimney Offset/Return - 30 deg
FS538
Ceiling Firestop - Straight
FS540
Ceiling Firestop - 30 deg
AS10
SL1100 Straight Attic Insulation Shield, 24 in. (610 mm)
JB577
Chimney Joint Band
CB576
Chimney Bracket
RF570
Roof Flashing - Flat to 6/12 Pitch
RF571
Roof Flashing - 6/12 to 12/12 Pitch
Chimney Sections
A
TR11
Round Termination Cap
TR11T
Round Telescoping Termination Cap
TR11TV
Round Telescoping Termination Cap-Top Vent
TCT1175
Terra Cotta Termination Cap
CT56
B
Chimney Stabilizer
SL1130
ST1175
13 in.
(330 mm)
11 in.
(279 mm)
Catalog #
in
B
mm
in
mm
SL1106
6
152
4-3/4
121
SL1112
12
305
10-3/4
273
SL1118
18
457
16-3/4
425
SL1136
36
914
34-3/4
883
SL1148
48
1219
46-3/4
1187
A = Actual Length
B = Effective Length (length of
chimney part after it has
been snapped to another)
Square Termination Cap
Chase Top
LDS33
Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)
LDS46
Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)
LDS-BV
Decorative Shroud - 26 in. x 26 in. (660 mm x 660 mm)
Field Constructed Shrouds (See “Woodburning Termination
Cap”)
CT-11A
Adapter-May be used with the following copper caps
CT-King
CT-Queen
Inside
Diameter
11 in.
(279 mm)
20-3/4 in.
(527 mm)
CT-Bishop I
CT-Bishop II
Outside Diameter
13 in.
(330 mm)
CT-Knight I
CT-Pawn
SL11 Vent Stabilizer
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
51
Inside
Diameter
11 in.
(279 mm)
21 in.
(533 mm)
Outside
Diameter
13 in.
(330 mm)
A
B
17 in. (432 mm)
SL1130 Offset/Return
Catalog #
A
B
FS538
0-deg.
17 in.
432 mm
FS540
30-deg.
26 in.
660 mm
15-1/4 in.
(387 mm)
Assembled
Diameter: 17 in./432 mm
Height: 24 in./610 mm
AS10 Straight Attic Insulation Shield
13 in.
(330 mm)
2 in.
(51 mm)
25-1/4 in.
(641 mm)
29 in.
(737 mm)
RF570 Roof Flashing
JB577 Chimney Joint Band
15-1/4in.
(387 mm)
13 in.
(330 mm)
CB576 Chimney Joint Band
39-7/8 in.
(1013 mm)
RF571 Roof Flashing
52
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
28 in.
(711 mm)
15-3/4 in.
(400 mm)
31-3/4 in.
(806 mm)
TR11 - Round Termination Cap
32-3/8 in.
(822 mm)
34-5/8 in.
(879 mm)
TR11-TV - Round Termination Cap
34-3/8 in.
(873 mm)
TR11T - Round Telescoping Termination Cap
TR-TVK
14-3/4 in.
(375 mm)
10 3/4 in.
23 in.
(584 mm)
23 in.
(584 mm)
ST1175 - Square Termination Cap
26 in.
20 in.
(508 mm)
17 in.
(432 mm)
CT11-A Adapter
9-3/8 in.
(238 mm)
9-1/4 in.
(235 mm)
TCT1175 - Terra Cotta Cap
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
53
72 in.
(1829 mm)
36 in.
(914 mm)
13-3/8 in.
(340 mm)
2 in.
(51 mm)
CT56 Chase Top
E
D
C
B
A
LDS-BV Decorative Shroud
Catalog #
LDS-BV
54
A
in.
26
mm
660
B
C
12-1/2 15-1/2
318
394
D
E
22
23
533
584
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08
6
10
Heatilator • Birmingham BIR42 • 4059-308 F • 11/08
11
16
Part numbers on following page.
12
13
17
14
15
Traditional Molded Brick Panel
9
8
7
1
5
4
3
2
11
Service Parts Diagram
42 in. Woodburning Fireplace
Service Parts
BIR42
18
19
11
22
23
20
21
05/08
Herringbone Molded Brick Panel
Beginning Manufacturing Date: April 2008
Ending Manufacturing Date: Active
Service Parts
PART NUMBER
4059-044
4059-351
4059-352
4059-353
4059-354
4059-355
Upper Left Panel
Lower Right Panel
Upper Right Panel
Lower Rear Panel
Upper Rear Panel
13
14
15
16
17
4059-360
4059-361
4059-362
Upper Right Panel
Lower Rear Panel
Upper Rear Panel
21
22
23
Outside Air Hood
Mortar
Contains:25 #6 X 1 1/2" Panhead screw, 3/32" Drill Bit, 17
T- Brackets, 2 Y-Brackets, 6 Clips,
Qty 2 req
4059-359
Lower Right Panel
20
4059-051
4059-316
4059-043
4059-358
Upper Left Panel
19
Refractory Fastener Pack
4059-357
Lower Left Panel
18
Herringbone Molded Brick Panel
4059-350
Lower Left Panel
12
25 LB Box
4059-033
Hearth Molded Brick Panel
11
Traditional Molded Brick Panel
GR29
Firescreen Assembly
Grate Assembly
4059-028
4059-111
9
Qty 2 req
Qty 2 req
4059-049
4059-312
10
Screen Rod Clips
Qty 2 req
Qty 2 req
OA Door
Screen Rod
7
8
4059-037
35159
Qty 2 req
Damper Control
Outside Air Collar Assembly
5
6
4059-030
Inner Transiton Collar
Damper Blade Assembly
3
4
4059-148
SERIAL #
24377
DESCRIPTION
Outer Transiton Assembly
Transition Assembly
2
1
ITEM
BIR42
05/08
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
Y
N
N
N
N
N
N
N
Stocked
at Depot
Beginning Manufacturing Date: April 2008
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or
replacement parts for your appliance please provide model number and serial number.
All parts listed in this manual may be ordered from an authorized dealer.
Service Parts List
42 in. Woodburning Fireplace
D. Service Parts
55
E. Contact Information
Hearth & Home Technologies Inc.
1915 W. Saunders Street
Mt. Pleasant, Iowa 52641
www.heatilator.com
Please contact your Heatilator dealer with any questions or concerns.
For the number of your nearest Heatilator dealer, please visit www.heatilator.com.
– NOTES –
Important operating •
and maintenance
instructions included.
Read, understand
and follow these
instructions for safe
installation and
operation.
•
Leave this manual with
party responsible for
use and operation.
T
O
N RD
O A
D SC
I
DO NOT DISCARD THIS MANUAL
•
D
CAUTION
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876,
4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983,
5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237,
5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079,
6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940,
6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039,
6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403,
1418504 or other U.S. and foreign patents pending.
56
Heatilator • Birmingham BIR42 • 4059-308 Rev F • 11/08