Canon PowerShot SX30 IS User guide

Camera User Guide
C
Y
P
O
• Make sure you read this guide, including the "Safety
Precautions" section, before using the camera.
• Store this guide safely so that you can use it in the future.
ENGLISH
Checking the Package Contents
Check if the following items are included in your camera package.
If anything is missing, contact the retailer from which you purchased the
camera.
Camera
(includes hot shoe cap)
Interface Cable
IFC-400PCU
Getting Started
Battery Charger
Battery Pack NB-7L
(with Terminal Cover) CB-2LZ/CB-2LZE
Y
P
O
Stereo AV Cable
AVC-DC400ST
C
Neck Strap
NS-DC11
DIGITAL CAMERA
Solution Disk
Warranty
Card
Lens Cap
Case for Hot
Shoe Cap
“Canon Customer
Support” Leaflet
Using the PDF Manuals
Also refer to the PDF manuals on the CD-ROM. After installation, shortcut icons
appear on the desktop. If the software installation fails, you can find the manuals in
the Readme folder on the CD-ROM.
• Camera User Guide (This Guide)
Once you have mastered the basics, use the camera’s many
features to shoot more challenging photos.
• Personal Printing Guide
Read when you want to connect the camera to a printer (sold
separately) and print.
• Software Guide
Read when you want to use the included software.
• A memory card is not included.
• Adobe Reader is required to view the PDF manuals.
2
Read This First
Test Shots and Disclaimer
Take some initial test shots and play them back to make sure the images
were recorded correctly. Please note that Canon Inc., its subsidiaries and
affiliates, and its distributors are not liable for any consequential damages
arising from any malfunction of a camera or accessory, including memory
cards, that results in the failure of an image to be recorded or to be recorded
in a way that is machine readable.
Warning Against Copyright Infringement
The images recorded with this camera are intended for personal use. Do not
record images that infringe upon copyright laws without the prior permission
of the copyright holder. Please be advised that in certain cases the copying
of images from performances, exhibitions, or commercial properties by
means of a camera or other device may contravene copyright or other legal
rights even if the image was shot for personal use.
Warranty Limitations
Y
P
O
This camera’s warranty is only effective in the country of sale. If there is a
problem with the camera while abroad, please return it to the country of sale
before proceeding with a warranty claim to a Canon Customer Support Help
Desk. For Canon Customer Support contacts, please see the customer
support list supplied with your camera.
C
LCD Monitor (Screen) and Electronic Viewfinder
• The LCD monitor and viewfinder are produced with extremely highprecision manufacturing techniques. More than 99.99% of the pixels
operate to specification, but occasionally non-performing pixels may
appear as bright or dark dots. This is not a malfunction and has no effect
on the recorded image.
• The LCD monitor may be covered with a thin plastic film for protection
against scratches during shipment. If so, remove the film before using the
camera.
Camera Body Temperature
Please take care when operating the camera for an extended period as the
camera body may become warm. This is not a malfunction.
3
What Do You Want to Do?
4
Shoot
● Shoot, leaving it to the camera to make settings .........................25
Take good people shots
I
w
Portraits
(p. 62)
P
At the beach
(p. 64)
Against snow
(p. 64)
Shoot various other scenes
J
Landscape
(p. 62)
Sports
(p. 62)
C
Shoot with special effects
Super vivid colors
(p. 65)
Y
P
O
Poster Effect
(p. 65)
Low Light
(p. 63)
O t
Foliage
(p. 64)
Fish-eye Effect
(p. 69)
Fireworks
(p. 64)
Miniature Effect
(p. 70)
● Focus on faces ............................................................25, 64, 84, 88
● Shoot in places where I cannot use the flash (turn off the flash) ......26
● Take pictures with me in them too (self-timer)...................61, 80, 81
● Insert the date and time into my shots .........................................60
4
What Do You Want to Do?
1
View
● Look at my pictures ......................................................................28
● Automatically play back pictures (slideshow).............................123
● Look at my pictures on a TV ......................................................127
● Look at my pictures on a computer. .............................................33
● Quickly search pictures ......................................................120, 121
● Erase pictures ......................................................................29, 132
Shoot/View Movies
E
Y
P
O 2
● Shoot movies .......................................................................30, 107
● View movies .................................................................................32
Print
C
● Easily print pictures ....................................................................144
Save
● Save images to a computer .........................................................33
Other
3
● Turn off sounds ............................................................................50
● Use the camera abroad........................................................15, 156
● Understand what is displayed on the screen .............................179
5
Table of Contents
Chapters 1 – 3 explain the basic operations and frequently used functions of
this camera. Chapters 4 onward explain the advanced functions, letting you
learn more as you read each chapter.
Checking the Package Contents .......2
Read This First ..................................3
What Do You Want to Do? ................4
Table of Contents ..............................6
Safety Precautions.............................9
Conventions Used in This Guide .....12
1 Getting Started................... 13
Charging the Battery........................14
Compatible Memory Cards (Sold
Separately) ......................................16
Inserting the Battery and Memory
Card .................................................16
Using the Screen .............................19
Setting the Date and Time ...............20
Setting the Display Language..........22
Formatting Memory Cards ...............23
Pressing the Shutter Button.............24
Taking Pictures (Smart Auto)...........25
Viewing Images ...............................28
Erasing Images................................29
Shooting Movies ..............................30
Viewing Movies................................32
Transferring Images to a Computer
for Viewing .......................................33
Accessories .....................................38
Separately Sold Accessories ...........39
C
MENU – Basic Operations .............. 49
Changing the Sound Settings ......... 50
Changing the Screen Brightness .... 51
Adjusting the Viewfinder.................. 52
Power Saving Function (Auto
Power Down)................................... 52
Returning the Camera to Default
Settings ........................................... 53
Low Level Memory Card
Formatting ....................................... 54
Clock Functions............................... 55
Y
P
O
3 Shooting with Commonly
Used Functions ..................57
Zooming in More Closely on
Subjects (Digital Zoom)................... 58
Inserting the Date and Time............ 60
Using the Self-Timer ....................... 61
Shooting in Various Conditions ....... 62
Shooting in Special Scenes ............ 63
Detecting a Smile and Shooting...... 66
Using the Wink Self-Timer .............. 67
Using the Face Self-Timer .............. 68
Shoot with the Effects of a
Fish-Eye Lens (Fish-eye Effect)...... 69
Take Shots That Look Like a
Miniature Model (Miniature Effect) .. 70
2 Learning More.................... 43
4 Choosing Settings
Yourself...............................71
Components Guide..........................44
Screen Display.................................46
Indicator ...........................................47
FUNC. Menu – Basic Operations ....48
Shooting in Program AE.................. 72
Turning the Flash On ...................... 72
Adjusting the Brightness (Exposure
Compensation)................................ 73
6
Table of Contents
Shooting Close-ups (Macro) ........... 73
Changing the Recording Pixel
Setting (Image Size) ....................... 74
Changing the Compression Ratio
(Image Quality) ............................... 74
Changing the ISO Speed ................ 76
Adjusting the White Balance ........... 77
Continuous Shooting....................... 78
Changing the Tone of an Image
(My Colors) ..................................... 79
Using the Self-Timer to Prevent
Camera Shake ................................ 80
Customizing the Self-Timer............. 81
Shooting Using a TV Monitor .......... 82
Changing the Composition with the
Focus Lock...................................... 82
Y
P
O
5 Getting More Out of Your
Camera................................83
C
Setting the Aperture Value .............. 96
Setting the Shutter Speed and
Aperture Value ................................ 97
Correcting the Brightness and
Shooting (i-Contrast) ....................... 98
Red-Eye Correction......................... 98
Shooting with Slow Synchro............ 99
Adjusting the Flash Exposure
Compensation ............................... 100
Adjusting the Flash Output ............ 100
Checking for Shut Eyes................. 101
Registering Shooting Settings ....... 102
Changing the Color and Shooting . 103
Shooting Stitch Assist Images....... 106
Changing the AF Frame Mode........ 84
Changing the AF Frame Position
and Size .......................................... 85
Magnifying the Focal Point.............. 86
Shooting with Servo AF .................. 86
Shooting with the AF Lock .............. 87
Choosing the Person to Focus On
(Face Select)................................... 88
Shooting in Manual Focus Mode .... 89
Focus Bracketing
(Focus-BKT Mode).......................... 90
Reacquiring Zoomed In Subjects
(Frame Assist)................................. 91
Changing the Metering Method....... 92
Shooting with the AE Lock .............. 93
Shooting with the FE Lock .............. 93
Auto Exposure Bracketing
(AEB Mode) .................................... 94
Setting the Shutter Speed............... 95
6 Using Various Functions for
Shooting Movies.............. 107
Shooting Movies in E Mode......... 108
Changing the Movie Mode ............ 108
Shoot Movies That Look Like a
Miniature Model (Miniature Effect) 109
Changing the Image Quality.......... 111
Taking Still Images while Shooting
a Movie.......................................... 112
AE Lock/Exposure Shift................. 113
Sound Settings .............................. 114
Other Shooting Functions.............. 115
Playback Functions ....................... 116
Editing ........................................... 117
7 Using Various Playback and
Editing Functions............ 119
Quickly Searching Images............. 120
Viewing Images in Filtered
Playback........................................ 121
Viewing Slideshows....................... 123
Checking the Focus....................... 124
Magnifying Images ........................ 125
7
Table of Contents
Displaying Various Images
(Smart Shuffle)...............................125
Changing Image Transitions..........126
Viewing Images on a TV................127
Viewing Images on a
High-Definition TV..........................128
Protecting Images..........................129
Erasing Images..............................132
Tagging Images as Favorites ........134
Organizing Images by Category
(My Category) ................................135
Rotating Images.............................137
Resizing Images ............................138
Trimming........................................139
Adding Effects with the My Colors
Function .........................................140
Correcting the Brightness
(i-Contrast).....................................141
Correcting the Red-Eye Effect .......142
C
Changing Camera Settings ........... 152
Changing Shooting Function
Settings ......................................... 158
Registering Commonly Used
Shooting Menus (My Menu) .......... 163
Changing Playback Function
Settings ......................................... 164
10Useful Information ...........165
Using Household Power................ 166
Using the Lens Hood
(Sold Separately) .......................... 167
Using an Externally Mounted
Flash (Sold Separately)................. 168
Using an Eye-Fi Card.................... 172
Troubleshooting ............................ 174
List of Messages That Appear on
the Screen..................................... 177
Information Displayed on the
Screen........................................... 179
Functions Available in Each
Shooting Mode .............................. 182
Menus ........................................... 184
Handling Precautions .................... 188
Specifications ................................ 189
Index ............................................. 192
Y
P
O
8 Printing ............................. 143
Printing Images..............................144
Printing from the Print List (DPOF) 146
Choosing Images for Printing
(DPOF) ..........................................147
Print Added Images .......................150
8
9 Customizing Camera Settings
...........................................151
Safety Precautions
• Before using the product, please ensure that you read the safety precautions
described below. Always ensure that the product is used correctly.
• The safety precautions noted on the following pages are intended to prevent injuries
to yourself and other persons, or damage to the equipment.
• Be sure to also check the guides included with any separately sold accessories you
use.
Warning
Denotes the possibility of serious injury or death.
• Do not trigger the flash in close proximity to human eyes.
Exposure to the intense light produced by the flash could damage eyesight. In
particular, remain at least one meter (39 inches) away from infants when using the
flash.
• Store this equipment out of the reach of children and infants.
Y
P
O
Strap: Putting the strap around a child’s neck could result in asphyxiation.
•
•
•
•
•
•
•
•
Use only recommended power sources.
Do not attempt to disassemble, alter or apply heat to the product.
Avoid dropping or subjecting the product to severe impacts.
To avoid the risk of injury, do not touch the interior of the product if it has been
dropped or otherwise damaged.
Stop using the product immediately if it emits smoke, a strange smell, or
otherwise behaves abnormally.
Do not use organic solvents such as alcohol, benzine, or thinner to clean the
equipment.
Do not let the product come into contact with water (e.g. sea water) or other
liquids.
Do not allow liquids or foreign objects to enter the camera.
C
This could result in electrical shock or fire.
If liquids or foreign objects come into contact with the camera interior, immediately
turn the camera power off and remove the battery.
If the battery charger becomes wet, unplug it from the outlet and consult your
camera distributor or the closest Canon Customer Support Help Desk.
• Do not play the supplied CD-ROM(s) in any CD player that does not support data
CD-ROMs.
Playing the CD-ROM(s) in an audio CD player (music player) could damage the
speakers. It is also possible to suffer hearing loss from listening with headphones
to the loud sounds of a CD-ROM played on a music CD player.
9
Safety Precautions
• Use only the recommended battery.
• Do not place the battery near or in direct flame.
• Unplug the power cord periodically and wipe away any dust and dirt that has
collected on the plug, the exterior of the power outlet, and the surrounding area.
• Do not handle the power cord with wet hands.
• Do not use the equipment in a manner that exceeds the rated capacity of the
electrical outlet or wiring accessories. Do not use if the power cord or plug are
damaged, or not fully plugged into the outlet.
• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals
or plug.
The battery may explode or leak, resulting in electrical shock or fire. This could
cause injury and damage the surroundings. In the event that a battery leaks and
the battery acid contacts eyes, mouth, skin or clothing, immediately flush with
water.
Caution
Y
P
O
Denotes the possibility of injury.
• Be careful not to bang the camera or subject it to strong impacts or shocks when
hanging it by the strap.
• Be careful not to bump or push strongly on the lens.
C
This could lead to injury or damage the camera.
• When using the flash, be careful not to cover it with your fingers or clothing.
This could result in burns or damage to the flash.
• Avoid using, placing or storing the product in the following places.
- Places subject to strong sunlight.
- Places subject to temperatures above 40 °C (104 °F).
- Humid or dusty areas.
These could cause leakage, overheating or an explosion of the battery, resulting in
electrical shock, fire, burns or other injuries.
High temperatures may cause deformation of the camera or battery charger
casing.
• The slideshow transition effects may cause discomfort when viewed for
prolonged periods.
Caution
Denotes the possibility of damage to the equipment.
• Do not aim the camera at bright light sources (the sun, etc.).
Doing so may damage the image sensor.
10
Safety Precautions
• When using the camera on a beach or at a windy location, be careful not to allow
dust or sand to enter the camera.
This may cause the camera to malfunction.
• In regular use, small amounts of smoke may be emitted from the flash.
This is due to the high intensity of the flash burning dust and foreign materials stuck
to the front of the unit. Please use a cotton swab to remove dirt, dust or other
foreign matter from the flash to prevent heat build-up and damage to the unit.
• Remove and store the battery when you are not using the camera.
If the battery is left inside the camera, damage caused by leakage may occur.
• Before you discard the battery, cover the terminals with tape or other insulators.
Contacting other metal materials may lead to fire or explosions.
• Unplug the battery charger from the power outlet after charging is complete, or
when you are not using it.
• Do not place anything, such as cloth on top of the battery charger while it is
charging.
Y
P
O
Leaving the unit plugged in for a long period of time may cause it to overheat and
distort, resulting in fire.
• Do not place the battery near pets.
Pets biting the battery could cause leakage, overheating or explosion, resulting in
fire or damage.
C
• When carrying the camera in a bag, close the screen to face inward to ensure
that hard objects to not come into contact with the screen.
• Do not attach accessories to the strap.
Doing so may cause malfunctions or damage the screen.
11
Conventions Used in This Guide
• Icons are used in the text to represent the camera buttons and control dial.
• Language that displays on the screen appears inside [ ] (square brackets).
• The directional buttons, control dial, and FUNC./SET button are
represented by the following icons.
FUNC./SET button
Up button
Right button
Left button
Control dial
Â
Down button
•
: Things you should be careful about
•
: Troubleshooting tips
•
: Hints for getting more out of your camera
•
: Supplemental information
• (p. xx): Reference pages (“xx” stands for a page number)
• This guide assumes all functions are at their default settings.
• The various types of memory cards that can be used in this camera are
collectively referred to as memory cards in this guide.
C
12
Y
P
O
1
Getting Started
This chapter explains preparations before shooting, how to shoot in
A mode, and then how to view and erase the images you take. The
latter part of this chapter explains how to shoot and view movies and
transfer images to a computer.
Y
P
O
Attaching Included Items/Holding the Camera
• Attach the included strap and place it around your neck to avoid dropping
the camera during use.
• Attach the included lens cap cord to the strap.
• Be sure to remove the lens cap before turning on the camera. Clip the lens
cap to the strap when not in use.
• When not in use, store the camera with the lens cap attached.
• Refer to p. 168 for details on the included case for the hot shoe cap.
C
Keep your arms tight against your body while
holding the camera firmly by the sides.
13
Charging the Battery
Use the included charger to charge the battery. Be sure to charge the battery
as it is not charged at the time of purchase.
Remove the cover.
Insert the battery.
● Align the o marks on the battery and
charger, then insert the battery by sliding it
in ( ) and down ( ).
Y
P
O
Charge the battery.
● For CB-2LZ: Flip out the plug (
) and
plug the charger into a power outlet ( ).
● For CB-2LZE: Plug the power cord into
C
CB-2LZ
CB-2LZE
the charger, then plug the other end into a
power outlet.
X The charge lamp lights orange and
charging starts.
X The charge lamp will light green when
charging has finished. Charging takes
approx. 2 hours and 20 minutes.
Remove the battery.
● Unplug the battery charger from the power
outlet, then remove the battery by sliding it
in ( ) and up ( ).
To protect the battery and prolong its life, do not charge it for longer than
24 hours continuously.
14
Charging the Battery
Approximate Number of Shots That Can Be Taken
LCD Monitor On*
Number of Shots
Approx. 370
Viewfinder On
Approx. 400
Approx. 10 hrs.
Playback Time
* The number of shots that can be taken is based on the Camera & Imaging Products
Association (CIPA) measurement standard.
• Under some shooting conditions, the number of shots that can be taken may be less
than mentioned above.
Battery Charge Indicator
An icon or message will appear on the screen indicating the battery’s charge state.
Display
Summary
Y
P
O
Sufficient charge.
Slightly depleted, but sufficient.
(Blinking red)
“Change the battery pack.”
Nearly depleted. Charge the battery.
Depleted. Recharge the battery.
Using the battery and charger effectively
C
• Charge the battery on the day, or the day before, it will be used.
Charged batteries continue to discharge naturally even if they are not used.
Attach the cover to a charged battery so that
the o mark is visible.
• How to store the battery for long periods:
Deplete and remove the battery from the camera. Attach the terminal cover and
store the battery. Storing a battery for long periods of time (about a year) without
depleting it may shorten its life span or affect its performance.
• The battery charger can also be used when abroad.
The charger can be used in regions that have 100 – 240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do
not use electrical transformers for foreign travel as they will cause damage.
• The battery may develop a bulge.
This is a normal characteristic of the battery and does not indicate a problem.
However, if the battery bulges to the point where it will no longer fit into the
camera, please contact a Canon Customer Support Help Desk.
• If the battery is quickly depleted even after charging, it has reached the end of
its life span. Purchase a new battery.
15
Compatible Memory Cards (Sold Separately)
• SD memory cards (2 GB and less)*
• SDHC memory cards (more than 2 GB, up to and including 32 GB)*
• SDXC memory cards
(more than 32 GB)*
• MultiMediaCards
• MMCplus memory cards
• HC MMCplus memory cards
• Eye-Fi Cards
* This memory card complies with the SD standards. Some cards may not operate
properly depending on the brand of card used.
Depending on your computer’s OS version, SDXC memory cards may not
be recognized when using a commercially available card reader. Check to
make sure that your OS supports this function beforehand.
About Eye-Fi Cards
Y
P
O
This product is not guaranteed to support Eye-Fi card functions (including
wireless transfer). In case of an issue with an Eye-Fi card, please check with
the card manufacturer.
Also note that an approval is required to use Eye-Fi cards in many countries
or regions. Without approval, use of the card is not permitted. If it is unclear
whether the card has been approved for use in the area, please check with
the card manufacturer.
C
Inserting the Battery and Memory Card
Insert the included battery and a memory card (sold separately).
Check the card’s write-protect tab.
● If the memory card has a write-protect tab,
you will not be able to record images if the
tab is in the locked position. Slide the tab
up until you hear a click.
16
Inserting the Battery and Memory Card
Open the cover.
● Slide the cover (
) and open it (
).
Insert the battery.
● Insert the battery as shown until it locks
into place with a click.
● Be sure to insert the battery in the correct
direction or it will not properly lock into
place.
Terminals
Y
P
O
Insert the memory card.
● Insert the memory card as shown until it
locks into place with a click.
C
Label
● Be sure the memory card is oriented
correctly. Inserting the memory card in the
wrong direction could damage the camera.
Close the cover.
● Close the cover (
), and press downward
as you slide it until it clicks into place ( ).
What if [Memory card locked] appears on the screen?
SD, SDHC and SDXC memory cards, and Eye-Fi cards have a write-protect tab.
If this tab is in the locked position, [Memory card locked] will appear on the screen
and you will not be able to take or erase images.
17
Inserting the Battery and Memory Card
Removing the Battery and Memory Card
Remove the battery.
● Open the cover and press the battery lock
in the direction of the arrow.
X The battery will pop up.
Remove the memory card.
● Push the memory card in until you hear a
click, then slowly release it.
X The memory card will pop up.
Y
P
O
Approximate Number of Shots per Memory Card
Memory Card
Number of Shots
4 GB
1058
16 GB
4334
• Values are based on the default settings.
• The number of shots that can be taken will vary depending on camera settings, the
subject and the memory card used.
C
Can you check the number of shots that can be taken?
You can check the number of shots that can be taken when the camera is in a
Shooting mode (p. 25).
Number of shots that can be taken
18
Using the Screen
Open the screen.
● Open the screen (
180°(
), and rotate it forward
).
● Close the screen (
).
Adjusting the position of the screen
Approx. 180°
Approx. 90°
Approx.
175°
•You can freely adjust the angle and orientation of
the screen as you like for the shooting
conditions.
Y
P
O
•Always keep the screen closed with it facing the
camera body when the camera is not in use.
• When the camera is on, opening the screen will turn the screen on and
the viewfinder off. Closing the screen with it facing the camera body will
turn the screen off and the viewfinder on.
C
• In a Shooting mode, if the screen is opened and rotated toward the lens,
the image will be flipped from left to right (mirror image). To cancel the
reverse display function, press the n button, choose the 4 tab and
[Reverse Disp.], then press the qr buttons to choose [Off].
19
Setting the Date and Time
The Date/Time settings screen will appear the first time the camera is turned
on. Since the dates and times recorded into your images are based on these
settings, be sure to set them.
Turn on the camera.
● Press the power button.
X The Date/Time screen will appear.
Set the date and time.
● Press the qr buttons to choose an option.
● Press the op buttons or turn the  dial
Y
P
O
to set a value.
C
Complete the setting.
● Press the m button.
X Once the date and time have been set, the
Date/Time screen will close.
● Pressing the power button will turn off the
camera.
Reappearing Date/Time screen
Set the correct date and time. If you have not set the date and time, the Date/Time
screen will appear each time you turn on the camera.
Daylight saving time settings
If you choose
in Step 2 and press the op buttons or turn the  dial and
choose
, you will set the time to daylight saving (1 hour ahead).
20
Setting the Date and Time
Changing the Date and Time
You can change the current date and time settings.
Display the menus.
● Press the n button.
Choose [Date/Time] in the 3 tab.
● Press the qr buttons to choose the 3
tab.
Y
P
O
● Press the op buttons or turn the  dial
to choose [Date/Time], then press the m
button.
C
Change the date and time.
● Follow Steps 2 and 3 on p. 20 to adjust the
setting.
● Pressing the n button will close the
menu.
Date/Time battery
• The camera has a built-in date/time battery (backup battery) that allows the
date/time settings to be retained for about three weeks after the battery pack
has been removed.
• By inserting a charged battery or connecting an AC adapter kit (sold separately,
p. 39) the date/time battery can be charged in about 4 hours even if the camera
is not turned on.
• If the date/time battery is depleted, the [Date/Time] menu will appear when you
turn the camera on. Follow the steps on p. 20 to set the date and time.
21
Setting the Display Language
You can change the language that displays on the screen.
Enter Playback mode.
● Press the 1 button.
Display the settings screen.
● Press and hold the m button, then
immediately press the n button.
Y
P
O
Set the display language.
● Press the opqr buttons or turn the Â
dial to choose a language, then press the
m button.
X Once the display language has been set,
C
the settings screen will close.
What if the clock appears when the m button is pressed?
The clock will appear if too much time passes between pressing the m button
and the n button in Step 2. If the clock appears, press the m button to
remove the clock and repeat Step 2.
You can also change the display language by pressing the n button,
choosing the 3 tab, and choosing the [Language] menu item.
22
Formatting Memory Cards
Before you use a new memory card or one that has been formatted in other
devices, you should format the card with this camera.
Formatting (initializing) a memory card erases all data on the memory card.
As you cannot retrieve the erased data, exercise adequate caution before
formatting the memory card.
Before formatting an Eye-Fi card (p. 172), be sure to install the software
contained on the card to a computer.
Display the menu.
● Press the n button.
Choose [Format].
● Press the qr buttons to choose the 3
Y
P
O
tab.
● Press the op buttons or turn the  dial
to choose [Format], then press the m
button.
C
Choose [OK].
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
Format the memory card.
● Press the op buttons or turn the  dial
to choose [OK], then press the m button.
X The memory card will be formatted.
Complete formatting.
X When formatting ends, [Memory card
formatting complete] will appear on the
screen.
● Press the m button.
23
Pressing the Shutter Button
Formatting or erasing data on a memory card merely changes the file
management information on the card and does not ensure its contents are
completely erased. Be careful when transferring or disposing of a memory
card. When disposing of a memory card, take precautions such as
physically destroying the card to prevent personal information leaks.
The total capacity of the memory card displayed in the formatting screen
may be less than indicated on the memory card.
Pressing the Shutter Button
To take images that are in focus, be sure to first press the shutter button
lightly (halfway) to focus, then press fully to shoot.
Y
P
O
Press halfway (Press lightly to focus).
● Press lightly until the camera beeps twice
C
and AF frames appear where the camera
focused.
Press fully (Press fully to shoot).
X The camera plays the shutter sound and
takes the shot.
● Since the shot is being taken while the
shutter sound plays, be careful not to move
the camera.
Does the length of the shutter sound change?
• Since the time required to shoot differs according to the scene you want to take,
the length of the shutter sound may change.
• If the camera or subject moves while the shutter sound is playing, the recorded
image may be blurry.
If you shoot without pressing the shutter button halfway, the image may not
be in focus.
24
Taking Pictures (Smart Auto)
Since the camera can determine the subject and shooting conditions, you can
let it automatically select the best settings for the scene and just shoot. The
camera can also detect and focus on faces, setting the color and brightness
to optimal levels.
Turn on the camera.
● Press the power button.
X The start-up screen will appear.
Choose A mode.
● Set the mode dial to A.
● When you point the camera toward the
Y
P
O
subject, the camera will make a slight
noise as it determines the scene.
X The icon for the determined scene will
appear in the upper right of the screen.
X The camera will focus on detected faces
and display frames on them.
C
Focus range (approx.)
Zoom bar
Compose the shot.
● Moving the zoom lever toward i
(telephoto) will zoom in on your subject,
making it appear larger. Moving the lever
toward j (wide angle) will zoom out from
your subject, making it appear smaller.
(The zoom bar showing the zoom position
appears on the screen.)
● If you move the zoom lever all the way
toward j (wide angle) or i (telephoto),
you will zoom quickly. If you move it
slightly, you will zoom slowly.
Focus.
● Press the shutter button halfway to focus.
25
Taking Pictures (Smart Auto)
X When the camera focuses, it will beep
twice and AF frames will appear where the
camera focused.
Several AF frames will appear when the
camera focuses on more than one point.
● If [Raise the flash] appears on the screen,
you should use the flash to shoot. Raise
the flash manually. When you are not
using the flash, manually lower it until it
closes (the flash will turn off).
AF Frame
Y
P
O
Shoot.
● Press the shutter button fully to shoot.
X The camera will play the shutter sound and
C
shoot. The flash will automatically fire in
low light conditions if it has been raised.
X The image will appear on the screen for
about two seconds.
● You can take a second picture even while
an image is displayed by pressing the
shutter button again.
What if an icon appears in the upper right of the screen?
The icon for the determined scene will appear in the upper right of the screen. For
details on the icons that appear, see “Scene Icons” (p. 180).
What is the rectangular gray frame?
This is the area that will be recorded in a movie. Movies can be shot simply by
pressing the movie button, no matter what position the mode dial is in (p. 107). To
hide the frame, choose [Custom Display], then [Shooting Info] and remove the
check mark (p. 160).
26
Taking Pictures (Smart Auto)
What if...
• What if the color and brightness of the images do not turn out as expected?
The scene icon (p. 180) that appears on the screen may not match the actual
scene. If this happens, try shooting in G mode (p. 71).
• What if the screen is off even the camera is turned on?
The display is set to the viewfinder. Press the l button several times to
restore the display to the screen.
• What if white and gray frames appear when you point the camera toward
a subject?
When faces are detected, a white frame appears on the face of the main
subject, while gray frames appear on other detected faces. The frames will
follow the subjects within a certain range (p. 84). If the main subject moves,
however, the gray frames will disappear, leaving only the white frame.
• What if a blue frame appears when you press the shutter button halfway?
A blue frame appears when a moving subject is detected; the focus and
exposure will continuously adjust (Servo AF).
•
flashes on the screen?
Attach the camera to a tripod so that the camera does not move and blur the
image.
• What if the camera does not play any sounds?
Pressing the l button while turning on the camera power will turn off all
sounds except for warning sounds. To turn the sounds on, press the n
button to choose [Mute] in the 3 tab, then press the qr buttons to choose [Off].
• What if the image comes out dark even if the flash fired when shooting?
The subject is too far away for the flash to reach. The effective flash range is
approximately 50 cm – 5.8 m (1.6 – 19 ft.) at maximum wide angle (j), and
approximately 1.4 – 2.8 m (4.6 – 6.6 ft.) at maximum telephoto (i).
• What if the camera beeps once when the shutter button is pressed halfway?
Your subject may be too close. Move the zoom lever toward i and hold it until
the lens stops moving. The camera will be at its maximum telephoto setting and
you will be able to focus on subjects that are about 1.4 m (4.6 ft.) or more away
from the end of the lens.
• What if the lamp lights when the shutter button is pressed halfway?
To reduce red-eye and to assist in focusing, the lamp may light when shooting
in dark areas.
• What if the h icon blinks when you try to shoot?
The flash is charging. You can shoot when recharging ends.
C
Y
P
O
27
Viewing Images
You can view the images you have taken on the screen.
Enter Playback mode.
● Press the 1 button.
X The last image you took will appear.
Choose an image.
● Pressing q or turning the  dial counterclockwise will cycle through the images in
the reverse order they were taken, from
the newest image to the oldest.
Y
P
O
● Pressing r or turning the  dial
clockwise will cycle through images in the
order they were taken, from oldest to
newest.
● The images change more quickly if you
C
keep the qr buttons pressed, but they will
appear coarse.
● The lens will retract after approximately 1
minute elapses.
● Pressing the 1 button again while the
lens is retracted will turn off the power.
Switching to Shooting mode
• Pressing the shutter button halfway while in Playback mode switches the
camera to Shooting mode.
28
Erasing Images
You can choose and erase images one at a time. Please note that erased
images cannot be recovered. Exercise adequate caution before erasing an
image.
Enter Playback mode.
● Press the 1 button.
X The last image you took will appear.
Choose an image to erase.
● Press the qr buttons or turn the  dial to
display an image to erase.
C
Y
P
O
Erase the image.
● Press the a button.
● Press the qr buttons or turn the  dial to
choose [Erase], then press the m button.
X The displayed image will be erased.
● To exit instead of erasing, press the qr
buttons or turn the  dial to choose
[Cancel], then press the m button.
29
Shooting Movies
The camera can automatically select all settings so that you can shoot movies
just by pressing the movie button. The audio will record in stereo.
Choose A mode.
● Set the mode dial to A.
Remaining Time
Y
P
O
Compose the shot.
● Moving the zoom lever toward i will zoom
C
in on your subject, making it appear larger.
Moving the lever toward j will zoom out
from your subject, making it appear smaller.
Shoot.
● Press the movie button.
Elapsed Time
X The camera will beep once, recording will
start, and [ Rec] and the elapsed time will
appear on the screen.
● Once shooting begins, take your finger off
the movie button.
● If you change the composition of your shot
during shooting, the focus, brightness and
tone will automatically adjust.
30
Shooting Movies
● Do not touch the microphone while
shooting.
● Do not press any buttons other than the
movie button while shooting. The sound the
buttons make will be recorded in the movie.
Microphone
Stop shooting.
● Press the movie button again.
X The camera will beep twice and stop
shooting the movie.
X The movie will record to the memory card.
X Shooting will automatically stop when the
Y
P
O
memory card fills.
Magnifying the subject while shooting
Pressing the zoom lever while shooting will zoom in on or out from the subject.
However, operation sounds will be recorded.
C
• When the mode dial is set to A, the icon for the determined scene will
appear (p. 180). “When Moving” icons and "With Strong Facial
Shadows" icons will not appear, however. Under certain conditions, the
icon that appears may not match the actual scene.
• Movies can be shot by pressing the movie button even when the mode
dial is in positions other than A (p. 107).
• When the mode dial is set to E, you can set each setting for shooting
movies (p. 107).
Estimated Shooting Times
Memory Card
4 GB
16 GB
20 min. 43 sec.
1 hr. 24 min. 54 sec.
Shooting Time
• Shooting times are based on default settings.
• Maximum clip length is approx. 29 min. 59 sec.
• Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 4 or higher memory cards are recommended.
31
Viewing Movies
You can view the movies you have shot on the screen.
Enter Playback mode.
● Press the 1 button.
X The last image you took will appear.
X
appears on movies.
Choose a movie.
● Press the qr buttons or turn the  dial to
choose a movie, then press the m button.
X The movie control panel will appear on the
screen.
C
Y
P
O
Play the movie.
● Press the qr buttons or turn the  dial to
choose
button.
(Play), then press the m
X The movie will play.
● If you press the m button, you can pause
or resume playback.
● Press the op buttons to adjust the
volume.
X After the movie finishes,
32
appears.
Transferring Images to a Computer for Viewing
What if you can’t play back movies on a computer?
• Install the included software (p. 34).
• When watching a movie on a computer, frames may drop, it may not play
smoothly, and the audio may stop suddenly depending on the computer’s
capabilities.
• If you use the supplied software to copy the movie back onto the memory card,
you can play back the movie smoothly with the camera. For enhanced playback
you can also connect the camera to a TV.
Transferring Images to a Computer for Viewing
Y
P
O
You can use the included software to transfer images you have shot with the
camera to a computer for viewing. If you are already using software included
with another Canon-brand compact digital camera, install the software from
the included CD-ROM, overwriting your current installation.
System Requirements
Windows
OS
Computer model
C
Windows 7
Windows Vista Service Pack 1 and 2
Windows XP Service Pack 3
The above OS should be pre-installed on computers with built-in
USB ports.
CPU
Pentium 1.3 GHz or higher (still images), Core2 Duo 1.66 GHz or
higher (movies)
RAM
Windows 7 (64 bit): 2 GB or more
Windows 7 (32 bit), Windows Vista (64 bit, 32 bit): 1 GB or more
Windows XP: 512 MB or more (still images), 1 GB or more (movies)
Interface
Free Hard Disk
Space
USB
ZoomBrowser EX: 200 MB or more
CameraWindow: 150 MB or more*
PhotoStitch: 40 MB or more
Display
1,024 x 768 pixels or higher
* For Windows XP, Microsoft .NET Framework 3.0 or later (max. 500 MB) must be
installed. Installation may take some time depending on your computer’s capabilities.
33
Transferring Images to a Computer for Viewing
Macintosh
OS
Computer model
Mac OS X (v10.4 – v10.6)
The above OS should be pre-installed on computers with built-in
USB ports.
CPU
PowerPC G4/G5 or Intel Processor (still images), Core Duo 1.66
GHz or higher (movies)
Mac OS X v10.4 – v10.5: 512 MB or more (still images), 1 GB or
more (movies)
Mac OS X v10.6: 1 GB or more
RAM
Interface
Free Hard Disk
Space
USB
ImageBrowser: 250 MB or more
CameraWindow: 150 MB or more
PhotoStitch: 50 MB or more
Display
1,024 x 768 pixels or higher
Preparations
Y
P
O
Windows Vista and Mac OS X (v10.5) are used for these explanations.
Install the Software.
C
Windows
Place the CD in the computer’s CDROM drive.
● Place the supplied CD-ROM (DIGITAL
CAMERA Solution Disk) (p. 2) into the
computer’s CD-ROM drive.
Begin installation.
● Click [Easy Installation] and follow the
on-screen instructions to proceed with the
installation.
● If the [User Account Control] window
appears, follow the on-screen instructions
to proceed.
34
Transferring Images to a Computer for Viewing
When the installation finishes, click
[Restart] or [Finish].
Remove the CD-ROM.
● Remove the CD-ROM when your desktop
screen appears.
Macintosh
Place the CD in the computer’s CDROM drive.
● Place the supplied CD-ROM (DIGITAL
CAMERA Solution Disk) (p. 2) into the
computer’s CD-ROM drive.
Y
P
O
Begin installation.
● Double-click the
on the CD.
● Click [Install], and follow the on-screen
C
instructions to proceed with the
installation.
Connect the camera to the
computer.
● Turn off the camera.
● Open the cover and insert the small plug of
the included interface cable (p. 2) firmly
into the camera terminal in the direction
shown.
● Insert the interface cable’s larger plug into
the computer. For connection details, refer
to the user guide provided with the
computer.
35
Transferring Images to a Computer for Viewing
Turn on the camera.
● Press the 1 button to turn on the camera.
Open CameraWindow.
Windows
● Click [Downloads Images From Canon
Camera using Canon CameraWindow].
X CameraWindow will appear.
● If CameraWindow does not appear, click
Y
P
O
the [Start] menu and choose [All
Programs], followed by [Canon Utilities],
[CameraWindow] and [CameraWindow].
C
Macintosh
X CameraWindow will appear when you
establish a connection between the
camera and computer.
● If CameraWindow does not appear, click
the CameraWindow icon on the Dock (the
bar which appears at the bottom of the
desktop).
For Windows 7, use the following steps to display CameraWindow.
Click
on the task bar.
In the screen that appears, click the
link to modify the program.
Choose [Downloads Images From Canon Camera using Canon
CameraWindow] and click [OK].
Double click
.
36
Transferring Images to a Computer for Viewing
Transfer and View Images
● Click [Import Images from Camera], and
then click [Import Untransferred Images].
X All images not previously transferred will
transfer to the computer. Transferred
images will be sorted by date and saved in
separate folders in the Pictures folder.
● When [Image import complete.] appears,
click [OK], then click [X] to close
CameraWindow.
● Turn off the camera and unplug the cable.
● For details on how to view images using a
Y
P
O
computer, refer to the Software Guide.
You can transfer images even without using the image transfer function in
the included software by simply connecting your camera to a computer.
There are, however, the following limitations.
C
• It may take a few minutes from when you connect the camera to the
computer until you can transfer images.
• Images shot in the vertical orientation may be transferred in the
horizontal orientation.
• Protection settings for images may be lost when transferred to a
computer.
• There may be problems transferring images or image information
correctly depending on the version of the operating system in use, the
file size, or the software in use.
• Some functions in the included software may not be available, such as
editing movies, and transferring images to the camera.
37
Accessories
Supplied with
Camera
DIGITAL CAMERA
Solution Disk
Neck Strap
NS-DC11
Battery Pack NB-7L
Battery Charger
with Terminal Cover* CB-2LZ/CB-2LZE*
Lens Cap
Stereo AV Cable
AVC-DC400ST*
Y
P
O
(includes hot shoe cap)
Interface Cable
IFC-400PCU*
Case for Hot
Shoe Cap
*Also available for purchase separately.
C
Memory Card
USB card reader
Windows/Macintosh
Canon-Brand PictBridge Compliant Printers
TV
HDMI Cable HTC-100
38
High-Definition TV
Separately Sold Accessories
The following camera accessories are sold separately. Some accessories are
not sold in some regions, or may no longer be available.
Power Supplies
Battery Charger CB-2LZ/CB-2LZE
● An adapter for charging Battery Pack
NB-7L.
Battery Pack NB-7L
● Rechargeable lithium-ion battery.
C
Y
P
O
AC Adapter Kit ACK-DC50
● This kit lets you power the camera using
household power. Recommended for
powering the camera for an extended
period of time or when connecting to a
computer or printer. Cannot be used to
charge the camera battery.
Using Accessories Abroad
The battery charger and the AC adapter kit can be used in regions that have 100 –
240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do
not use electrical transformers for foreign travel as they will cause damage.
39
Separately Sold Accessories
Flash
Speedlite 270EX/430EX II/580EX II
● A shoe-mounted flash that allows for a
wide range of flash photography.
Speedlite 430EX and 580EX may also be used.
Speedlite Bracket SB-E2
● Prevents unnatural shadows from
appearing on the sides of objects when
shooting from a vertical position, and is
useful for shooting portraits. The Off
Camera Shoe Cord OC-E3 is supplied with
this bracket.
Speedlite Transmitter ST-E2
● This allows the wireless control of slave
(remote) Speedlite flashes (except the
Speedlite 270EX).
C
Y
P
O
Other Accessories
HDMI Cable HTC-100
● Use this cable to connect the camera to
the HDMI™ terminal on a high-definition
TV set.
Lens Hood LH-DC60
● Prevents extraneous light from entering
the lens and causing flares or ghosting,
which reduce image quality.
40
Separately Sold Accessories
Filter Adapter FA-DC67A
● This adapter is required for attaching a
67mm filter.
Canon-brand Lens Filter (67 mm dia.)
● Protects the lens and allows you to shoot
with various effects.
Printers
SELPHY series
PIXMA series
C
Canon-Brand PictBridge Compliant
Printers
● By connecting your camera to a Canonbrand PictBridge compliant printer, you
can print your images without having to
use a computer.
For more information, visit your nearest
Canon retailer.
Y
P
O
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories. Canon shall not be liable for any damage to this product and/or
accidents such as fire, etc., caused by the malfunction of non-genuine Canon
accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this
warranty does not apply to repairs arising out of the malfunction of non-genuine Canon
accessories, although you may request such repairs on a chargeable basis.
41
C
42
Y
P
O
2
Learning More
This chapter explains the parts of the camera and what appears on the
screen, as well as the basic operating instructions.
C
Y
P
O
43
Components Guide
Y
P
O
Zoom Lever
Shooting: i (Telephoto) / j (Wide
Angle) (pp. 25, 30, 58)
Playback: k (Magnify) / g (Index)
(pp. 120, 125)
Shutter Button (p. 24)
Strap Mount (p. 13)
Mode Dial
Flash (pp. 26, 72)
Hot Shoe Cap (p. 168)
Mode Dial
C
Microphone (p. 31)
h (Flash) Button (p. 72)
Speaker
Lamp (pp. 61, 67, 68, 80, 81, 158, 159)
Focal Length (approx.)
Lens
Lens Hood / Lens Filter Mount (p. 167)
Tripod Socket
Memory Card / Battery Cover (p. 17)
DC Coupler Cable Port (p. 166)
Use the mode dial to change the Shooting mode.
P, Tv, Av, M, C1, C2 Mode
Choose settings yourself to take
various types of pictures (p. 72).
Auto Mode
You can leave it to the
camera to select settings for
fully automatic shooting
(pp. 25, 30).
Movie Mode
Choose settings yourself
to shoot movies (p. 107).
Even if the mode dial is
set to a position other
than Movie mode, movies
can be shot by pressing
the movie button (p. 30).
Scene Mode
You can shoot with the best settings for the scene or add
various effects and shoot (pp. 62, 63).
44
Components Guide
Screen (LCD Monitor) (pp. 19, 46, 179,
181)
(Short Cut) (p. 162) /
c (Direct Print) (p. 144) Button
Diopter Adjustment Dial (p. 52)
Viewfinder (p. 46)
Movie Button (pp. 30, 107)
Indicator (p. 47)
Power Button (p. 20)
(Zoom Framing Assist) (p. 91) /
d (Jump) (p. 121) Button
HDMI Terminal (p. 128)
1 (Playback) Button (pp. 28, 119)
C
A/V OUT (Audio/Video Output) /
DIGITAL Terminal (pp. 35, 127, 144)
(AF Frame Selector) (pp. 85, 88) /
a (Single Image Erase) Button (p. 29)
n Button (p. 49)
l (Display) Button (p. 46)
e (Macro) (p. 73) /
f (Manual Focus) (p. 89) / q Button
b (Exposure Compensation) (p. 73) /
o Button
- (p. 76) / r Button
m FUNC./SET Button (p. 48)
Q (Self-Timer) (pp. 61, 80, 81) /
p Button
Control Dial
Y
P
O
Control Dial
Turning the control dial allows you to perform
operations such as choosing items or
switching images. Except for a few
operations, the same operations are possible
with the opqr buttons.
45
Screen Display
Switching the Display
You can change the screen display using the l button. Refer to p. 179
for details on information that appears on the screen.
Opening the screen with the power on will turn the screen on, and turn the
viewfinder off. Closing the screen so that it faces inward will turn the screen
off, and turn the viewfinder on (p. 19).
Shooting
LCD Monitor (Screen)
Display 1
Playback
No Information
Display
Viewfinder
Y
P
O
Display 2
C
Simple Information
Display
Display 1
Detailed Information
Display
Display 2
Focus Check
Display (p. 124)
You can also switch the display by pressing the l button while the
image displays right after shooting. However, Simple Information Display
is not available. You can change the display that appears first by pressing
the n button, then choosing [Review info] in the 4 tab (p. 160).
46
Indicator
Screen Display in Dark Shooting Conditions
The display automatically brightens when shooting in dark conditions,
allowing you to check the composition (Night Display function). However, the
brightness of the image on the screen, and the brightness of the actual image
recorded may be different. Screen noise may appear and the movement of
the subject may appear somewhat jagged on the screen. This has no effect
on the recorded image.
Overexposure Warning during Playback
In “Detailed Information Display” (p. 46), overexposed areas of the image
flash on the screen.
Histogram during Playback
High
Low
Dark
Bright
Indicator
C
● The graph that appears in “Detailed
Y
P
O
Information Display” (p. 46) is called the
histogram. The histogram shows the
distribution of brightness in an image
horizontally, and the amount of brightness
vertically. When the graph approaches the
right side, the image is bright, but when it
approaches the left side, the image is dark,
and in this way you can judge the
exposure.
● The histogram can also be displayed while
shooting (p. 160).
The indicator on the back of the camera (p. 45) will light or blink depending
on the camera’s status.
Colors
Green
Status
Lights
Blinks
Operation Status
When the camera is on.
Recording/reading/transmitting image data.
When the indicator blinks green, data is being recorded/read or various
information is being transmitted.
Do not turn off the power, open the memory card slot/battery cover, shake
or jolt the camera. These actions may corrupt the image data or cause the
camera or memory card to malfunction.
47
FUNC. Menu – Basic Operations
You can set commonly used functions using the ø menu.
The menu items and options differ depending on the Shooting mode (pp. 182
– 183).
Choose a Shooting mode.
● Set the mode dial to the desired shooting
mode.
Display the ø menu.
● Press the m button.
Y
P
O
Choose a menu item.
● Press the op buttons to choose a menu
item.
X The available options for the menu item
C
Available Options
Menu Items
appear in the lower part of the screen.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option.
● You can also choose settings by pressing
the l button on options that display
.
Complete the setting.
● Press the m button.
X The shooting screen will reappear and the
setting you chose will display on the
screen.
48
MENU – Basic Operations
Various functions can be set from the menus. The menu items are organized
under tabs, such as for shooting (4) and playback (1). The options differ
depending on the Shooting mode and the Playback mode (pp. 184 – 187).
Display the menu.
● Press the n button.
Choose a tab.
● Press the qr buttons, or move the zoom
lever left or right to choose a tab.
Y
P
O
Choose an item.
● Press the op buttons or turn the  dial
to choose an item.
● Some items require you to press the m or
C
r button to display a submenu in which
you change the setting.
Choose an option.
● Press the qr buttons to choose an option.
Complete the setting.
● Press the n button to restore the
normal screen.
49
Changing the Sound Settings
You can silence or adjust the volume of camera sounds.
Muting Sounds
Display the menu.
● Press the n button.
Choose [Mute].
● Press the qr buttons to choose the 3 tab.
● Press the op buttons or turn the  dial
to choose [Mute], then press the qr
buttons to choose [On].
Y
P
O
● Press the n button to restore the
normal screen.
You can also mute camera sounds by holding down the l button and
turning on the power.
C
Adjusting the Volume
Display the menu.
● Press the n button.
Choose [Volume].
● Press the qr buttons to choose the 3 tab.
● Press the op buttons or turn the  dial
to choose [Volume], then press the m
button.
Change the volume.
● Press the op buttons or turn the  dial
to choose an item, then press the qr
buttons to adjust the volume.
● Press the n button twice to restore
the normal screen.
50
Changing the Screen Brightness
The screen brightness can be changed in two ways.
You can set the brightness of the screen and the viewfinder separately.
(Press the l button to switch to the desired display before making
settings).
Using the Menu
Display the menu.
● Press the n button.
Choose [LCD Brightness].
● Press the qr buttons to choose the 3 tab.
● Press the op buttons or turn the  dial
Y
P
O
to choose [LCD Brightness].
Change the brightness.
● Press the qr buttons to change the
C
brightness.
● Press the n button twice to restore
the normal screen.
Using the l Button
● Press the l button for more than one
second.
X The screen increases to maximum
brightness regardless of the setting in the
3 tab.
● Pressing the l button again for more
than one second will return the screen to
the original brightness.
• The next time you turn on the camera, the screen will be at the
brightness setting chosen in the 3 tab.
• When you have set the brightness to its highest setting in the 3 tab, you
cannot change the brightness with the l button.
51
Adjusting the Viewfinder
You can adjust the viewfinder so that the display is clearly visible (Dioptric
adjustment).
Set the viewfinder display.
● Press the l button several times until
the viewfinder turns on (p. 46).
Adjust the diopter.
● Adjust the dial while looking through the
viewfinder.
● Adjustments of -4.0 to +1.0 m-1 (dpt) can
Y
P
O
be made.
Power Saving Function (Auto Power Down)
To save battery power, the screen turns off, and the camera shuts down
automatically when it is not operated for a certain time.
C
Power Saving during Shooting
The screen will turn off approximately 1 minute after the camera is last
operated. After about 2 more minutes, the lens will retract and the power will
turn off. When the screen has turned off but the lens has not yet retracted,
pressing the shutter button halfway (p. 24) turns on the screen and shooting
can continue.
Power Saving during Playback
The power will turn off approximately 5 minutes after the camera is last
operated.
• You can turn off the power saving function (p. 155).
• You can adjust the time before the screen turns off (p. 156).
52
Returning the Camera to Default Settings
When you have mistakenly changed a setting, you can reset the camera to
the default settings.
Display the menu.
● Press the n button.
Choose [Reset All].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons or turn the  dial
to choose [Reset All], then press the m
button.
Y
P
O
Reset the settings.
● Press the qr buttons or turn the  dial to
C
choose [OK], then press the m button.
X The camera will reset to the default
settings.
Are there functions that cannot be reset?
• The [Date/Time] (p. 21) in the 3 tab, [Language] (p. 22), [Video System]
(p. 127), [Time Zone] (p. 156), and the image registered in [Start-up Image]
(p. 153).
• The saved data for custom white balance (p. 77).
• Colors that were chosen in Color Accent (p. 103) or Color Swap (p. 104).
• The scene mode chosen in K (p. 63).
• The Movie mode (p. 108)
53
Low Level Memory Card Formatting
Perform low level formatting when [Memory card error] appears, the camera
does not operate properly, or you think that the recording/reading speed of a
memory card has dropped. As you cannot retrieve the erased data, exercise
adequate caution before formatting the memory card.
Display the menu.
● Press the n button.
Choose [Format].
● Press the qr buttons to choose the 3
tab.
● Press the op buttons or turn the  dial
Y
P
O
to choose [Format], then press the m
button.
C
Choose [Low Level Format].
● Press the op buttons or turn the  dial
to choose [Low Level Format], then press
the qr buttons to display
.
● Press the opqr buttons or turn the Â
dial to choose [OK], then press the m
button.
Start the low level format.
● Press the op buttons or turn the  dial
to choose [OK], then press the m button.
X Low level formatting starts.
X When low level formatting ends, [Memory
card formatting complete] will appear.
54
Clock Functions
Complete the low level format.
● Press the m button.
• Low level formatting may take longer than standard formatting (p. 23),
since all recorded data is erased.
• You can stop a low level format of a memory card by choosing [Stop].
When stopping low level formatting, the data will be erased but the
memory card can be used without problem.
Clock Functions
Y
P
O
You can check the current time.
● Press and hold the m button.
X The current time appears.
● If you hold the camera vertically while
C
using the clock function, it will switch to
vertical display. Press the qr buttons or
turn the  dial to change the display
color.
● Press the m button again to cancel the
clock display.
When the camera power is off, press and hold the m button, then press
the power button to display the clock.
55
C
56
Y
P
O
3
Shooting with Commonly
Used Functions
Y
P
O
This chapter explains how to shoot in different conditions, as well as
how to use common functions, such as the self-timer.
C
• This chapter assumes the camera is set to A mode for “Zooming in
More Closely on Subjects (Digital Zoom)” (p. 58) to “Using the Self-Timer”
(p. 61). When shooting in a mode other than A, check which functions
are available in that mode (pp. 182 – 185).
• “Shooting in Various Conditions” (p. 62) to “Shooting in “Take Shots That
Look Like a Miniature Model (Miniature Effect)” (p. 70) assumes that the
corresponding mode has been chosen.
57
Zooming in More Closely on Subjects
(Digital Zoom)
You can use the digital zoom to zoom up to approximately 140x and capture
subjects that are too far away for the optical zoom to enlarge. The images
may appear coarse, however, depending on the recording pixel setting (p. 74)
and the zoom factor used.
Move the zoom lever toward i.
● Hold the lever until zooming stops.
X The zoom will stop when the largest
possible zoom factor without image
deterioration has been reached, and the
zoom factor will appear when you release
the zoom lever.
Zoom Factor
Y
P
O
Move it toward i again.
X The digital zoom will zoom in even further
C
on the subject.
What if the zoom factor appears in blue?
Images shot at zoom factors that appear in blue will be coarse.
Turning off the digital zoom
To turn off the digital zoom, press the n button to choose [Digital Zoom] in
the 4 tab, then choose [Off].
The focal length when using the optical zoom and digital zoom together is
24 – 3360 mm, and 24 – 840 mm when using the optical zoom alone (all
focal lengths are 35mm film equivalent).
58
Zooming in More Closely on Subjects (Digital Zoom)
Digital Tele-Converter
The focal length of the lens can be increased by approx. 1.7x or approx. 2.1x.
This enables a faster shutter speed and less chance of camera shake than
the zoom (including digital zoom) used by itself at the same zoom factor. The
images may appear coarse, however, depending on the combination of
recording pixel (p. 74) and digital tele-converter settings used.
Choose [Digital Zoom].
● Press the n button.
● Press the qr buttons to choose the 4
tab.
Y
P
O
● Press the op buttons or turn the  dial
to choose [Digital Zoom].
Accept the setting.
● Press the qr buttons to choose a
C
magnification.
● Pressing the n button will restore the
shooting screen.
X The view will be enlarged and the zoom
factor will appear on the screen.
● To return to standard digital zoom, choose
[Digital Zoom] and the [Standard] option.
What if the zoom factor appears in blue?
Using this function at a recording pixel setting of
,
deterioration (the zoom factor will appear in blue).
or
will cause image
• The respective focal lengths when using [1.7x] and [2.1x] are 40.8 –
1428 mm and 50.4 – 1764 mm (35mm film equivalent).
• The digital tele-converter cannot be used together with the digital zoom.
59
Inserting the Date and Time
You can insert the shooting date and time in the lower right corner of an
image. Once inserted, however, they cannot be deleted. Be sure to check
beforehand that the date and time are correctly set (p. 20).
Choose [Date Stamp].
● Press the n button.
● Press the qr buttons to choose the 4 tab.
● Press the op buttons or turn the  dial
to choose [Date Stamp].
Accept the setting.
● Press the qr buttons to choose [Date] or
Y
P
O
[Date & Time].
● Pressing the n button will restore the
shooting screen.
X Once set, [DATE] will appear on the screen.
Shoot.
C
X The shooting date or time will be recorded
in the image’s lower right corner.
● To restore to the original setting, choose
[Off] in Step 2.
You can insert and print the shooting date in images which do not have an
embedded date and time as follows. However, if you do this for images
with an embedded date and time, the date and time may be printed twice.
• Use the DPOF print settings (p. 147) to print.
• Use the included software to print.
Refer to the Software Guide for details.
• Print using printer functions.
Refer to the Personal Printing Guide for details.
60
Using the Self-Timer
The self-timer can be used to shoot a group photo that includes the
photographer. The camera will shoot approximately 10 seconds after the
shutter button is pressed.
Press the p button.
Choose Ò.
● Press the op buttons or turn the  dial
to choose Ò, then press the m button.
Y
P
O
X Once set, Ò will appear on the screen.
C
Shoot.
● Press the shutter button halfway to focus
on the subject, then press it fully.
X When the self-timer starts, the lamp blinks
and the self-timer sound plays.
X Two seconds before the shutter releases,
the lamp and sound speed up (the lamp
remains lit when the flash will fire).
● To cancel shooting with the timer after
countdown has started, press the p button.
● To restore the original setting, choose
in Step 2.
You can change the delay time and number of shots (p. 81).
61
Shooting in Various Conditions
The camera will select the necessary settings for the conditions in which you
wish to shoot when you choose the matching mode.
Choose a Shooting mode.
● Set the mode dial to the desired Shooting
mode.
Shoot.
I Take portraits (Portrait)
● Produces a soft effect when
photographing people.
Y
P
O
JTake landscapes (Landscape)
● Lets you shoot majestic landscapes with a
C
real sense of depth.
Take shots of moving subjects
(Sports)
● Shoots continuous images while focusing
automatically.
● At maximum wide angle setting you will be
able to focus on subjects that are about
1 m (3.3 ft.) or more away from the end of
the lens, and at maximum telephoto setting
you will be able to focus on subjects that
are about 10 m (33.8 ft.) or more away
from the end of the lens.
In
mode, images may appear coarse because the ISO speed (p. 76)
is increased to match the shooting conditions.
62
Shooting in Special Scenes
The camera will select the necessary settings for the conditions in which you
wish to shoot when you choose the matching mode.
Enter K mode.
● Set the mode dial to K.
Choose the Shooting mode.
● After pressing the m button, press the
op buttons to choose
.
● Press the qr buttons or turn the  dial to
Y
P
O
choose a Shooting mode, then press the
m button.
C
Shoot.
Take shots in low light conditions
(Low Light)
● Lets you can shoot in dark places with
reduced camera shake and subject blur.
● A recording pixel setting of
will display,
and the image will be fixed at 1600 x 1200
pixels.
63
Shooting in Special Scenes
w
Take shots of people at the beach
(Beach)
● Lets you take shots of brightly lit people on
sandy beaches where the reflected
sunlight is strong.
O
Take shots of foliage (Foliage)
● Lets you shoot trees and leaves, such as
new growth, autumn leaves or blossoms,
in vivid colors.
P
Y
P
O
Take shots of people in snow
(Snow)
● Lets you take bright, natural-colored shots
of people against snowy backgrounds.
C
t Take shots of fireworks (Fireworks)
● Lets you take shots of fireworks in vivid
colors.
In t mode, attach the camera to a tripod to prevent the camera from
moving and blurring the image. Additionally, you should set the [IS Mode]
to [Off] when shooting with a tripod (p. 161).
64
Shooting in Special Scenes
Adding Effects and Shooting
Shoot images with vivid colors
(Super Vivid)
● Lets you take shots with vivid, intense
colors.
Take posterized shots
(Poster Effect)
● Lets you take shots that look like an old
poster or illustration.
Y
P
O
Since you may not achieve the expected results with images shot in
and
, try taking some test shots first.
C
65
Detecting a Smile and Shooting
The camera will shoot, even without pressing the shutter button, when it
detects a smile.
Choose
.
● Follow Steps 1 – 2 on p. 63 to choose
,
then press the l button.
● Press the qr buttons or turn the  dial to
choose
, then press the l button.
X The camera will enter shooting stand-by,
and [Smile Detection on] will appear on the
screen.
Y
P
O
Point the camera at a person.
● Each time the camera detects a smile it will
shoot after the lamp lights.
● Pressing the p button will pause smile
C
detection. Press the p button again to
resume smile detection.
What if a smile is not detected?
Smiles are easier to detect if the subject faces the camera, and opens their mouth
enough to show some teeth when smiling.
Changing the number of shots
After choosing
in Step 1, press the op buttons.
• You should switch to another mode when you finish shooting, or the
camera will continue taking shots each time the camera detects a smile.
• You can also shoot by pressing the shutter button.
66
Using the Wink Self-Timer
Point the camera at a person and press the shutter button fully. The camera
will shoot approximately two seconds after it detects a wink.
Choose
.
● Follow Steps 1 – 2 on p. 63 to choose
,
then press the l button.
● Press the qr buttons or turn the  dial to
choose
, then press the l button.
Compose the shot and press the
shutter button halfway.
● Confirm that a green frame appears around
Y
P
O
the face of the person who will wink.
Press the shutter button fully.
X The camera will enter shooting stand-by,
C
and [Wink to take picture] will appear on the
screen.
X The lamp will blink and the self-timer sound
will play.
Face the camera and wink.
X The shutter will release approximately 2
seconds after a wink is detected from the
person with a frame around the person’s face.
● To cancel the countdown, press the p
button.
What if a wink is not detected?
• Wink a bit slowly.
• A wink may not be detected if eyes are covered by hair or a hat, or when wearing
glasses.
Changing the number of shots
After choosing
in Step 1, press the op buttons.
67
Using the Face Self-Timer
• Shutting both eyes will also be detected as a wink.
• If a wink is not detected, the shutter will release approximately 15
seconds later.
• If there are no people in the shot when the shutter button is pressed fully,
the camera will shoot after a person enters the shot and winks.
Using the Face Self-Timer
The shutter will release approximately two seconds after the camera detects
a new face (p. 84). You can use this when the photographer wants to be in
the image, such as a group photo.
Choose
.
Y
P
O
● Follow Steps 1 – 2 on p. 63 to choose
,
then press the l button.
● Press the qr buttons or turn the  dial to
choose
, then press the l button.
Compose the shot and press the
shutter button halfway.
C
● Make sure a green frame appears on the
face focused on and white frames appear
on other faces.
Press the shutter button fully.
X The camera will enter shooting stand-by,
and [Look straight at camera to start count
down] will appear on the screen.
X The lamp will blink and the self-timer sound
will play.
Join the subjects and look at the
camera.
X When the camera detects a new face, the
lamp and sound will speed up (the lamp
remains lit when the flash will fire), and two
seconds later the shutter will release.
● To cancel shooting with the timer after
countdown has started, press the p button.
68
Shoot with the Effects of a Fish-Eye Lens (Fish-eye Effect)
Changing the number of shots
After choosing
in Step 1, press the op buttons.
Even if your face is not detected after joining the subjects, the shutter will
release approximately 15 seconds later.
Shoot with the Effects of a Fish-Eye Lens
(Fish-eye Effect)
Lets you shoot with the distorting effect of a fish-eye lens.
Y
P
O
Choose
.
● Follow Steps 1 – 2 on p. 63 to choose
.
Choose an effect level.
C
● Press the l button.
X [Effect Level] will appear on the screen.
● Press the qr buttons or turn the  dial to
choose an effect level, then press the
l button.
X You can check the effect on the screen.
Shoot.
Since you may not achieve the expected results depending on the
shooting conditions, try taking some test shots first.
69
Take Shots That Look Like a Miniature
Model (Miniature Effect)
Blurs chosen portions in the top and bottom of an image to produce the effect
of a miniature model.
Choose
.
● Follow Steps 1 – 2 on p. 63 to choose
X A white frame (the area that will not be
.
blurred) appears on the screen.
Choose the area to keep in focus.
● Press the l button.
● Move the zoom lever to change the frame
Y
P
O
size, and press the op buttons to change
the frame position.
● Pressing the l button restores the
shooting screen.
C
Shoot.
• If you press the m button in Step 2, the horizontal/vertical orientation of
the frame will switch, and you can use the qr buttons to change the
frame position when it is displayed vertically.
• Holding the camera vertically will change the orientation of the frame.
• Since you may not achieve the expected results depending on the
shooting conditions, try taking some test shots first.
Modes for other scenes
In addition to the modes explained here, the following scene modes are also
available:
• T Color Accent (p. 103)
• Y Color Swap (p. 104)
• xvStitch Assist (p. 106)
70
4
Choosing Settings Yourself
In this chapter you will learn how to use the various functions in G
mode to progressively advance your shooting skills.
C
Y
P
O
• This chapter assumes that you have set the mode dial to G.
• G stands for Program AE.
• Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those modes
(pp. 182 – 185).
71
Shooting in Program AE
You can choose the settings for various functions to suit your preferences.
AE stands for Auto Exposure.
The focusing range is approximately 5 cm (2.0 in.) – infinity at maximum wide
angle (j), and approximately 1.4 m (4.6 ft.) – infinity at maximum telephoto
(i).
Enter G mode.
● Set the mode dial to G.
Adjust the settings according to
your purposes (pp. 72 – 81).
Shoot.
Y
P
O
What if the shutter speed and aperture value appear in orange?
If a correct exposure cannot be obtained when pressing the shutter button
halfway, the shutter speed and aperture value are shown in orange. Try the
following settings to obtain the correct exposure.
• Turn on the flash
• Choose a higher ISO speed (p. 76)
C
Turning the Flash On
You can make the flash fire every time you shoot. The effective flash range is
approximately 50 cm – 5.8 m (1.6 – 19 ft.) at maximum wide angle (j), and
approximately 1.4 – 2.8 m (4.6 – 6.6 ft.) at maximum telephoto (i).
Raise the flash.
Choose h.
● After pressing the h button, press the qr
buttons or turn the  dial to choose h,
then press the m button.
X Once set, h will appear on the screen.
What if the setting screen does not appear even when you
press the h button?
The flash is lowered. Raise the flash manually.
72
Adjusting the Brightness (Exposure Compensation)
You can adjust the standard exposure set by the camera in 1/3-stop
increments in the range of -2 to +2.
Enter Exposure Compensation
mode.
● Press the o button.
Adjust the brightness.
● While watching the screen, turn the  dial
to adjust the brightness, then press the o
button.
X The exposure compensation amount will
appear on the screen.
Y
P
O
Shooting Close-ups (Macro)
You can shoot an object at a close distance or even shoot extreme close-ups
of it. The focusing range is approximately 0 cm – 50 cm (0 – 1.6 ft.) at
maximum wide angle j.
C
Choose e.
● After pressing the q button, press the qr
buttons or turn the  dial to choose e,
then press the m button.
X Once set, e will appear on the screen.
• In macro shooting, the edges of the image may darken if the flash fires.
• Be careful to avoid damaging the lens.
How can I take better close-ups?
Try attaching the camera to a tripod and shooting in Î to prevent the camera from
moving and blurring the image (p. 80).
For macro shooting, e will turn gray in the area that displays in the yellow
bar underneath the zoom bar, and the camera will not focus.
73
Changing the Recording Pixel Setting
(Image Size)
You can choose from five recording pixel (image size) settings.
Choose the recording pixel setting.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m button.
X The setting will appear on the screen.
Y
P
O
Changing the Compression Ratio
(Image Quality)
You can choose from the following two compression ratios (image quality):
(Fine),
(Normal).
C
Choose the compression ratio
setting.
● After pressing the m button, press the
op buttons to choose
l button.
, then press the
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m button.
X The setting will appear on the screen.
74
Changing the Compression Ratio (Image Quality)
Approximate Values for Recording Pixels and Compression
Ratio
Recording Pixels
Compression
Ratio
Single Image Data
Size (Approx. KB)
Number of Shots per
Memory Card
(Large)
14M/4320x3240
3597
4 GB
1058
16 GB
4334
1719
2194
8985
(Medium 1)
7M/3072x2304
1897
1978
8101
902
4022
16473
(Medium 2)
2M/1600x1200
558
6352
26010
278
12069
49420
150
20116
82367
84
30174
123550
2024
1856
7602
968
3771
15443
(Small)
0.3M/640x480
(Widescreen)
3744x2104
Y
P
O
• The values in the table are measured according to Canon standards and may change
depending on the subject, memory card and camera settings.
C
Approximate Values for Paper Size
A2
A3 – A5
●
●
Suitable for sending images as e-mail
attachments.
For printing on wide size paper.
5" x 7"
Postcard size
3.5" x 5"
75
Changing the ISO Speed
Choose the ISO speed.
● After pressing the m button, press the qr
buttons or turn the  dial to choose an
option, then press the m button.
X The setting will appear on the screen.
Automatically adjusts the ISO speed to the Shooting mode and shooting
conditions.
Low Fine weather conditions, outdoor shooting.
Cloudy, twilight
High Nightscapes, dark interiors
Y
P
O
Changing the ISO speed
• Lowering the ISO speed results in sharper images, but there may be an
increased chance of subject or image blurring in certain shooting conditions.
C
• Raising the ISO speed results in a faster shutter speed, reducing image blurring
and letting the flash reach greater distances to the subject. The images,
however, will appear coarse.
When the camera is set to
, you can press the shutter button halfway
to display the automatically set ISO speed.
76
Adjusting the White Balance
The white balance (WB) function sets the optimal white balance for natural
looking colors to match the shooting conditions.
Choose the white balance function.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m button.
X The setting will appear on the screen.
Y
P
O
Auto
Automatically sets the optimal white balance for the shooting conditions.
Day Light
Fine weather conditions, outdoor shooting
Cloudy
Cloudy, shady, twilight conditions
Tungsten
Tungsten, bulb-type (3-wavelength) fluorescent lighting
Fluorescent
Warm-white fluorescent, cool-white fluorescent, warm-white-type
(3-wavelength) fluorescent lighting
C
Fluorescent H Daylight fluorescent, daylight-type (3-wavelength) fluorescent lighting
h Flash
Custom
For shooting with the flash.
Manually sets a custom white balance.
Custom White Balance
You can adjust the white balance to the light source at the shooting location.
Make sure that you set the white balance under the light source of the actual
scene you will shoot.
● In Step 2 above, choose
.
● Make sure the entire screen is filled with a
plain, white colored subject, then press the
l button.
X The tint on the screen will change when a
white balance data is set.
If you change camera settings after recording white balance data, the tone
may not turn out properly.
77
Continuous Shooting
As long as you hold the shutter button down, the camera will shoot
continuously.
Choose a Drive mode.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose W or
, then press the m button.
Shoot.
Y
P
O
X As long as you hold the shutter button down,
the camera will shoot successive images.
Mode
W Continuous
Continuous
Shooting AF
Maximum
Speed
(Approx.
images/sec.)
Description
C
1.3
The camera shoots continuously with the focus and
exposure set when the shutter button is pressed halfway.
The camera shoots continuously and focuses.
The [AF Frame] is set to [Center].
The camera shoots continuously with the focus fixed to
Continuous
0.6
the position set in manual focus. In t mode, the focus
Shooting LV*
is locked on the first shot.
* When in t (p. 64), AF lock (p. 87) or manual focus modes (p. 89),
will change to
.
0.6
• Cannot be used with the self-timer (pp. 61, 80, 81).
• Continuous shooting speed increases in
mode (p. 63).
• Depending on the shooting conditions, the camera settings and the
zoom position, the camera may stop shooting momentarily, or the
shooting speed may slow down.
• As the number of images increases, the shooting speed may slow down.
• If the flash fires, the shooting speed may slow down.
78
Changing the Tone of an Image (My Colors)
You can change the tone of an image to sepia or black and white when
shooting.
Choose My Colors.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m
X The setting will appear on the screen.
My Colors Off
Neutral
Sepia
B/W
Positive Film
Y
P
O
—
Emphasizes the contrast and color saturation for a vivid
impression.
Tones down the contrast and color saturation for neutral
hues.
Vivid
Sepia tones.
C
Black and white.
Combines the effects of Vivid Red, Vivid Green and Vivid
Blue to produce intense natural appearing colors like those
obtained with positive film.
Lighter Skin Tone
Makes skin tones lighter.
Darker Skin Tone
Makes skin tones darker.
Vivid Blue
Emphasizes blue tints. Makes the sky, ocean and other
blue subjects more vivid.
Vivid Green
Emphasizes green tints. Makes mountains, foliage and other
green subjects more vivid.
Vivid Red
Emphasizes red tints. Makes red subjects more vivid.
Custom Color
You can adjust contrast, sharpness, and color saturation
etc. to your preference (p. 80).
• The white balance cannot be set in the
and
modes (p. 77).
• In
and
modes, colors other than people’s skin color may change.
You may not obtain the expected results with some skin colors.
79
Using the Self-Timer to Prevent Camera Shake
Custom Color
The contrast, sharpness, color saturation, red, green, blue, and skin tones in
an image can be chosen and set at 5 different levels.
● Follow Step 2 on p. 79 to choose
, then
press the l button.
● Press the op buttons to choose an
option, then press the qr buttons or turn
the  dial to choose a value.
● The more to the right, the stronger/darker
(skin tone) the effect gets, the more to the
left, the weaker/lighter (skin tone) the
effect gets.
Y
P
O
● Press the l button to complete the
setting.
Using the Self-Timer to Prevent Camera Shake
C
The camera will shoot approximately two seconds after the shutter button is
pressed, preventing any camera shake that occurs when pressing the shutter
button.
Choose Î.
● After pressing the p button, press the
op buttons or turn the  dial to choose
Î, then press the m button.
X Once set, Î will appear on the screen.
● Follow Step 3 on p. 61 to shoot.
80
Customizing the Self-Timer
You can set the time delay (0 – 30 seconds) and the number of shots (1 – 10
shots).
Choose $.
● After pressing the p button, press the
op buttons or turn the  dial to choose
$, then press the n button
immediately.
Choose the settings.
● Press the op buttons to choose [Delay]
Y
P
O
or [Shots].
● Press the qr buttons or turn the  dial to
choose a value, then press the m button.
● Follow Step 3 on p. 61 to shoot.
What if the number of shots is set to two or more shots?
C
• Exposure and white balance settings are set with the first shot.
• If the flash fires or you set a high number of shots, shooting interval may take
longer than usual.
• If the memory card becomes full, shooting stops automatically.
When you set the time delay for more than 2 seconds, the self-timer lamp
and sound speed up 2 seconds before the shutter releases (when the flash
will fire, the lamp lights).
81
Shooting Using a TV Monitor
You can use a TV to display the camera screen content while shooting.
• To connect the camera to a TV, follow the Steps in “Viewing Images on a
TV” (p. 127).
• Shooting procedures are the same as when using the camera screen.
TV display is not available when using HDMI Cable HTC-100 (sold
separately) to connect the camera to a high-definition TV.
Changing the Composition with the
Focus Lock
Y
P
O
While you keep the shutter button pressed halfway, the focus and exposure
are locked. You can now recompose and shoot. This is called Focus Lock.
Focus.
● Center the subject you want in focus, and
C
press the shutter button halfway.
● Confirm that the AF Frame on the subject
is green.
Recompose.
● Keep the shutter button pressed halfway
and move the camera to recompose the
scene.
Shoot.
● Press the shutter button fully.
82
5
Getting More Out of Your
Camera
Y
P
O
This chapter serves as the advanced version of Chapter 4 and explains
how to take pictures using various functions.
C
• This chapter assumes that you have set the mode dial to G.
• The sections “Setting the Shutter Speed” (p. 95), “Setting the Aperture
Value” (p. 96), “Setting the Shutter Speed and Aperture Value” (p. 97),
assume that you have set the mode dial to the corresponding mode.
• The section “Adjusting the Flash Output” (p. 100) assumes that you have
set the mode dial to D.
• The sections “Changing the Color and Shooting” (p. 103) and “Shooting
Stitch Assist Images” (p. 106) assume that you have set the mode dial to
K and chosen the corresponding mode.
• Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those modes
(pp. 182 – 185).
83
Changing the AF Frame Mode
You can change the AF (Auto Focus) frame mode to match the scene you
want to shoot.
Choose [AF Frame].
● After pressing the n button, choose
[AF Frame] in the 4 tab, then press the
qr buttons to choose an option.
FlexiZone/Center
The AF frame is locked to the center. This is effective for focusing on a specific point.
In [FlexiZone], you can change the position and size of the AF frame (p. 85).
Y
P
O
If the camera cannot focus when you press the shutter button halfway, the
AF frame will turn yellow and
will appear.
Face Detect
• Detects people’s faces and sets the focus, exposure (evaluative metering
only) and white balance (
only).
• When the camera is pointed at subjects, a white frame appears on the face
the camera judges to be the main subject, and gray frames (max. 2) will
appear on other faces.
• A frame will follow a moving subject within a certain range.
• When the shutter button is pressed halfway, up to 9 green frames will
appear on faces that the camera focuses on.
C
• If a face is not detected and only gray frames (no white frame) appear,
an AF Frame will appear in the center of the screen when you press the
shutter button halfway.
• The AF frame will appear in the center of the screen if you press the
shutter button halfway when Servo AF (p. 86) is set to [On] and a face is
not detected.
• Examples of faces that cannot be detected:
• Subjects that are far away or extremely close.
• Subjects that are dark or light.
• Faces turned to the side or at a diagonal, or faces with a portion hidden.
• The camera may mistakenly identify non-human subjects as a face.
• If the camera cannot focus when you press the shutter button halfway,
the AF frame will not appear.
84
Changing the AF Frame Position and Size
When the AF frame mode is set to [FlexiZone] (p. 84) you can change the
position and size of the AF frame.
Press the
button.
X The AF frame will turn orange.
Move the AF frame.
● Turn the  dial to move the AF frame.
● Press the opqr buttons to make fine
adjustments.
Y
P
O
● If you keep the
button pressed, the AF
frame will return to the original position
(center).
C
Change the AF frame size.
● Press the l button.
X The AF frame will become small.
● Pressing the l button again will
restore the AF frame to normal size.
Complete the settings.
● Press the
button.
• The Spot AE Point frame can be linked with the AF frame (p. 92).
• The AF frame will be set to normal size when using Digital Zoom (p. 58)
or Digital Tele-converter (p. 59).
85
Magnifying the Focal Point
If you press the shutter button halfway, the AF frame will magnify and you can
check the focus.
Choose [AF-Point Zoom].
● Press the n button to choose [AFPoint Zoom] in the 4 tab, then press the
qr buttons to choose [On].
Check the focus.
● Press the shutter button halfway.
X In [Face Detect] (p. 84), the face detected
Y
P
O
as the main subject will appear magnified.
X In [FlexiZone] or [Center] (p. 84), the
contents of the AF frame will appear
magnified.
What if the display does not magnify?
C
The display will not appear magnified in [Face Detect] if a face cannot be detected
or is too big in relation to the screen. In [FlexiZone] or [Center], it will not appear
magnified if the camera cannot focus.
The magnified display will not appear when using Digital Zoom (p. 58), Digital
Tele-converter (p. 59), Servo AF or when connected to a TV (p. 82).
Shooting with Servo AF
While the shutter button is pressed halfway, the focus and exposure will
continue to adjust, allowing you to take pictures of moving subjects without
missing a shot.
Choose [Servo AF].
● Press the n button to choose [Servo
AF] in the 4 tab, then press the qr
buttons to choose [On].
86
Shooting with the AF Lock
Focus.
● The focus and exposure will be maintained
where the blue AF frame appears while
you press the shutter button halfway.
• The camera may not be able to focus in some conditions.
• In low light conditions, AF frames may not turn blue even after pressing
the shutter button halfway. In this case, you can set the focus and
exposure with the AF frame setting.
• If a correct exposure cannot be obtained, the shutter speed and aperture
value appear in orange. Release your finger from the shutter button, then
press it again halfway.
Y
P
O
• You cannot shoot with the AF lock in this mode.
• The [AF-Point Zoom] option in the 4 tab is not available in Servo AF
mode.
• Not available when using Self-Timer (pp. 61, 80, 81).
C
Shooting with the AF Lock
The focus can be locked. After locking the focus, the focal distance will not
change even when you release your finger from the shutter button.
Lock the focus.
● Keep the shutter button pressed halfway
and press the q button.
X The focus locks, and
and the MF
indicator appear on the screen.
● After you release your finger from the
shutter button, press the q button again,
then press the qr buttons or turn the Â
dial to choose
. The focus will unlock.
Compose the scene and shoot.
87
Choosing the Person to Focus On (Face Select)
You can choose a specific person’s face to focus on and then shoot.
Set the AF frame to [Face Detect]
(p. 84).
Enter Face Select mode.
● Point the camera toward the face of the
subject and press the
button.
X After [Face Select: On] appears, a face
frame
will appear around the face
detected as the main subject.
● Even if the subject moves, the face frame
Y
P
O
will follow the subject within a certain
range.
● If a face is not detected,
will not
appear.
C
Choose the face to focus on.
● If you press the
button, the face frame
will move to another face detected by
the camera.
● When the frame has made a full circuit of
all detected faces, [Face Select: Off] will
appear, and the AF frame mode screen will
reappear.
Shoot.
● Press the shutter button halfway. When
the camera focuses,
.
will change into
● Press the shutter button fully to shoot.
88
Shooting in Manual Focus Mode
You can use manual focus when auto focus is not possible. If you press the
shutter button halfway after roughly focusing manually, you can fine tune the
focus.
Choose
.
● After pressing the q button, press the qr
buttons or turn the  dial to choose
then press the m button.
X
,
and the MF indicator appear.
Focusing roughly.
Y
P
O
● The side bar shows your focal point and an
MF distance indicator. While looking at the
magnified area, turn the  dial to find an
approximate focus.
C
MF Distance Indicator
Fine tuning the focus.
● If you press the shutter button halfway or
press the
button, you can fine tune the
focus (Safety MF).
• You cannot change the AF mode setting or size while focusing manually
(p. 84). If you want to change the AF frame mode or size, cancel Manual
focus mode first.
• In order to focus accurately, try attaching the camera to a tripod.
• When using the Digital Zoom (p. 58), Digital Tele-converter (p. 59), or
when using a television as a display (p. 82), you will be able to focus but
the magnified area will not display.
• If you press the n button and [MF-Point Zoom] is set to [Off] in the
4 tab, the magnified display will not be available.
• If you press the n button to display the 4 tab and set [Safety MF]
to [Off], you will not be able to fine tune the focus even if you press the
shutter button halfway.
89
Focus Bracketing (Focus-BKT Mode)
The camera automatically takes three continuous shots in the following order:
one at the position set in manual focus, and one each with focus positions
preset farther and nearer. The focus adjustment can be set in 3 levels.
Choose
.
● After pressing the m button, press the
op buttons to choose
, then press the
qr buttons or turn the  dial to choose
.
Set the focus.
Y
P
O
● Press the l button.
● Press the qr buttons or turn the  dial to
make the setting.
C
• In flash settings other than ! (p. 26), Focus Bracketing is not available.
• Continuous shooting (p. 78) cannot be used in this mode.
• Only three shots will be taken, even if you use $ (p. 81) to set a different
number of shots.
• If you follow Step 1 on p. 89 to choose
and immediately press the
l button, the focus bracketing screen will appear.
90
Reacquiring Zoomed In Subjects
(Frame Assist)
If you lose track of your subject while zoomed in, zooming out will make it
easier to find.
Look for the subject.
● Press and hold the
button.
X The camera will zoom out, and the area
that appeared on the screen before
pressing the
button will appear as a
white frame on the screen.
Y
P
O
Reacquire the subject.
C
● Place the subject inside the white frame
and release the
button.
X The camera will return to the original zoom
position.
• While the camera is zoomed out, shooting information will not appear on
the screen.
• If you press the shutter button halfway while in the screen of Step 1, you
can shoot at that zoom factor.
• The white frame will not appear even if you press the
button while
shooting a movie. The sound of the camera zooming out and any
operation sounds will be recorded.
• Zoom Framing Assist is not available after fully pressing the shutter
button when using the self-timer (pp. 61, 80, 81),
or
. In addition,
automatic shooting in [Smile] mode is not available while pressing the
button.
Changing the Displayed Area when Pressing the
Press the n button to choose [
from three effect levels.
Button
Display Area] in the 4 tab, then choose
91
Changing the Metering Method
You can change the metering method (brightness measuring function) to
match the shooting conditions.
Choose the metering method.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m button.
X The setting will appear on the screen.
Y
P
O
Suitable for standard shooting conditions, including back lit shots.
Automatically adjusts the exposure to match the shooting
conditions.
Center
Averages the light metered from the entire frame, but gives greater
Weighted Avg. weight to the center.
Only meters within the
(Spot AE Point frame). The Spot AE
Spot
Point frame can be linked to the AF frame.
Evaluative
C
Linking the Spot AE Point Frame to the AF
Frame
Choose
.
● Follow Step 2 above and choose
.
Choose [Spot AE Point].
● Press the n button to choose [Spot
AE Point] in the 4 tab, then press the qr
buttons to choose [AF Point].
X The Spot AE Point frame will be linked to
the AF frame that was moved.
Cannot be used when [AF Frame] is set to [Face Detect] (p. 84).
92
Shooting with the AE Lock
You can lock the exposure and shoot, or set the focus and exposure
separately to shoot. AE stands for “Auto Exposure”.
Lock the exposure.
● Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X When
appears, the exposure will be
locked.
● If you release your finger from the shutter
button and press the o button again,
will disappear and AE will unlock.
Y
P
O
Compose the scene and shoot.
Program Shift
If you lock the exposure and turn the  dial, you can change the shutter speed
and aperture value combination.
C
Shooting with the FE Lock
Just as with the AE lock, you can lock the exposure for shooting with the flash.
FE stands for “Flash Exposure”.
Raise the flash and choose h
(p. 72).
Lock the flash exposure.
● Point the camera toward the subject and
press the o button while pressing the
shutter button halfway.
X The flash will fire and when
appears,
the flash output will be retained.
● If you release your finger from the shutter
button and press the o button again,
will disappear and FE will unlock.
93
Auto Exposure Bracketing (AEB Mode)
Compose the scene and shoot.
Auto Exposure Bracketing (AEB Mode)
The camera takes 3 continuous shots while automatically adjusting the
exposure to standard exposure, underexposure and overexposure, in that
order.
Choose
.
● After pressing the m button, press the
op buttons to choose
, then press the
qr buttons or turn the  dial to choose
.
Y
P
O
Set the exposure compensation
amount.
C
● Press the l button.
● Press the qr buttons or turn the  dial to
adjust the setting.
● From the exposure set by the camera, you
can adjust the amount of compensation ±2
stops in 1/3-stop increments. If exposure
compensation (p. 73) is already being
used, settings are made with the
compensated value as the base.
• In flash settings other than ! (p. 26), AEB is not available.
• Continuous shooting (p. 78) cannot be used in this mode.
• If you press the l button while in the exposure compensation screen
(p. 73), the compensation amount setting screen will appear.
• Only three shot will be taken, even if you use $ (p. 81) to set a different
number of shots.
94
Setting the Shutter Speed
You can set the shutter to the speed at which you want to shoot. The camera
will set the appropriate aperture value for the shutter speed you set.
M stands for “Time value”.
Set the mode dial to M.
Make the setting.
● Turn the  dial to set the shutter speed.
Shoot.
Available Shutter Speeds
Y
P
O
15", 13", 10", 8", 6", 5", 4", 3"2, 2"5, 2", 1"6, 1"3, 1", 0"8, 0"6, 0"5, 0"4, 0"3, 1/4, 1/5, 1/6,
1/8, 1/10, 1/13, 1/15, 1/20, 1/25, 1/30, 1/40, 1/50, 1/60, 1/80, 1/100, 1/125, 1/160, 1/200,
1/250, 1/320, 1/400, 1/500, 1/640, 1/800, 1/1000, 1/1250, 1/1500, 1/1600, 1/2000,
1/2500, 1/3200
• 2" indicates 2 seconds, 0"3 indicates 0.3 second and 1/160 indicates 1/160
second.
C
• The fastest shutter speed when using the flash is 1/2000 second. The camera
automatically resets the shutter speed to 1/2000 second if a faster shutter speed
is chosen.
• Depending on the zoom position, some shutter speeds may not be available.
• When shutter speeds of 1.3 seconds or slower are used, images are
processed to eliminate noise after being taken. A certain amount of
processing time may be needed before you can take the next shot.
• You should set the [IS Mode] to [Off] when lowering the shutter speed
and shoot with a tripod (p. 161).
What if the aperture value appears in orange?
If the aperture value appears in orange when the shutter button is pressed
halfway, the scene has exceeded the correct exposure limits. Adjust the shutter
speed until the aperture value appears in white. Safety shift can also be used
(p. 96).
95
Setting the Aperture Value
You can set the aperture to a value at which you want to shoot. The camera
will set the appropriate shutter speed for the aperture value you set.
B stands for “Aperture value”, which refers to the size of the aperture
opening inside the lens.
Set the mode dial to B.
Make the setting.
● Turn the  dial to set the aperture value.
Shoot.
Y
P
O
Available Aperture Values
F2.7, F3.2, F3.5, F4.0, F4.5, F5.0, F5.6, F5.8, F6.3, F7.1, F8.0
• Depending on the zoom position, some aperture values may not be available.
What if the shutter speed appears in orange?
C
If the shutter speed appears in orange when the shutter button is pressed halfway,
the scene has exceeded the correct exposure limits. Adjust the aperture value
until the shutter speed appears in white. Safety shift can also be used.
Safety Shift
With M and B modes, if you press the n button and [Safety Shift] is set
to [On] in the 4 tab, the shutter speed or aperture value is automatically adjusted
for the correct exposure when it cannot otherwise be obtained.
Safety Shift is disabled when the flash is enabled.
96
Setting the Shutter Speed and Aperture Value
You can manually set the shutter speed and aperture to shoot images.
D stands for “Manual”.
Set the mode dial to D.
Make the setting.
● Press the o button to choose the shutter
speed or aperture value.
● Turn the  dial to set a value.
X The set exposure level appears on the
Aperture Value
Shutter Speed
Exposure Level
Indicator
Y
P
O
X When the difference is more than ±2 stops,
the set exposure level appears in orange.
When you press the shutter button halfway,
“-2” or “+2” appears in orange.
Standard
Exposure Level
Exposure Level
indicator. You can check the difference
against the standard exposure level.
C
• The standard exposure is calculated according to the metering method
chosen (p. 92).
• If you use the zoom after making settings or changing the composition,
the exposure level may change.
• Depending on the shutter speed or aperture value set, the screen
brightness may change. If the flash is raised and the mode set to h, the
screen brightness will not change.
• If you press the o button while holding down the shutter button halfway,
the shutter speed or aperture value (whichever is not set in Step 2), will
automatically adjust to obtain the correct exposure (the correct exposure
may not be obtained depending on the settings).
97
Correcting the Brightness and Shooting
(i-Contrast)
The camera can detect areas in the scene, such as faces or backgrounds,
that are too bright or dark and automatically adjust them to the optimum
brightness when shooting. Also, when the overall image is lacking in contrast,
the camera will automatically correct the image for a sharper impression
when shooting.
Choose [i-Contrast].
● Press the n button, choose the 4
tab, and then choose the [i-Contrast] menu
item. Press the qr buttons to choose
[Auto].
X Once set, @ will appear on the screen.
Y
P
O
Under some conditions, the image may appear coarse or may not be
corrected properly.
You can correct recorded images (p. 141).
C
Red-Eye Correction
You can automatically correct red-eye that occurs in images taken with the flash.
Choose [Flash Control].
● Press the n button to choose [Flash
Control] in the 4 tab, then press the m
button.
Adjust the setting.
● Press the op buttons or turn the  dial
to choose [Red-Eye Corr.], then press the
qr buttons to choose [On].
X Once set, Πwill appear on the screen.
98
Shooting with Slow Synchro
Red-eye correction may be applied to areas other than red eyes. For
example, when red make-up has been used around eyes.
• You can correct recorded images (p. 142).
• If you hold down the h button for more than one second, the screen in
Step 2 will appear.
• With the flash raised, if you press the h button and immediately press
the n button, the screen in Step 2 will appear.
Shooting with Slow Synchro
You can make the main subject, such as people, appear bright by having the
camera provide the appropriate illumination with the flash. At the same time,
you can use a slow shutter speed to brighten the background that the light
from the flash cannot reach.
Y
P
O
Raise the flash.
C
Choose ….
● After pressing the h button, press the qr
buttons or turn the  dial to choose …,
then press the m button.
X Once set, … will appear on the screen.
Shoot.
● Even if the flash fires, ensure that the
subject does not move until the shutter
sound ends.
Attach the camera to a tripod to prevent the camera from moving and
blurring the image. Additionally, you should set the [IS Mode] to [Off] when
shooting with a tripod (p. 161).
99
Adjusting the Flash Exposure Compensation
Just like with Exposure Compensation (p. 73), you can adjust the exposure
±2 stops in 1/3-stop increments when using the flash.
Choose ~.
● After pressing the m button, press the
op buttons to choose ~.
Make the setting.
● Press the qr buttons or turn the  dial to
choose the amount of flash exposure
compensation, then press the m button.
X Once set, ~ will appear on the screen.
Safety FE
Y
P
O
The camera automatically changes the shutter speed or aperture value when the
flash fires to avoid overexposing and blowing out the highlights in the scene.
However, if you press the n button to display the 4 tab and set [Safety FE]
to [Off] in [Flash Settings], the shutter speed and aperture value will not
automatically adjust.
C
• You can also set the flash exposure compensation. Press the n
button and choose [Flash Control] (p. 98) from the 4 tab. Then choose
[Flash Exp. Comp] and press the qr buttons to choose a setting.
• When you press and hold the h button for 1 sec. or more, or with the
flash raised, if you press the h button and immediately press the n
button, the settings screen will appear.
Adjusting the Flash Output
In D mode, you can choose 3 levels of flash output.
Set the mode dial to D.
Choose Flash Output.
● After pressing the m button, press the
op buttons to choose ~.
100
Checking for Shut Eyes
Make the setting.
● Press the qr buttons or turn the  dial to
choose the amount of flash output, then
press the m button.
X Once set, ~ will appear on the screen.
• You can also set the flash output. Press the n button and choose
[Flash Control] (p. 98) from the 4 tab. Then choose [Flash Output] and
press the qr buttons to choose a setting.
• In M and B modes, you can set the flash output if you press the
n button and choose the 4 tab, then [Flash Control] and set the
[Flash Mode] option to [Manual].
• When you press and hold the h button for 1 sec. or more, or with the
flash raised, if you press the h button and immediately press the n
button, the settings screen will appear.
Y
P
O
Checking for Shut Eyes
C
When the camera detects the possibility that people have their eyes shut,
appears.
Choose [Blink Detection].
● Press the n button, then choose
[Blink Detection] in the 4 tab. Press the
qr buttons to choose [On].
Shoot.
X When a person with shut eyes is detected,
a frame and
appear.
• In
or $ mode, when the number of shots is set to two or more, this
function is only available for the last image shot.
• In
and
shot.
modes, this function is only available for the last image
• Not available in W,
, or
mode.
101
Registering Shooting Settings
You can register commonly used shooting modes and settings to your
preference. To switch between registered settings, simply turn the mode dial
to
or
. Even if you switch shooting modes or turn off the power, settings
that usually cancel (self timer, etc.) will be saved.
Settings that Can be Registered
•
•
•
•
•
•
Shooting modes (G, M, B and D)
Items set in G, M, B or D (pp. 73 – 97)
Items in the shooting menu
Zoom position
Manual focus position (p. 89)
My Menu items (p. 163)
Y
P
O
Enter the shooting mode you want
to register and make the settings.
Choose [Save Settings].
C
● Press the n button, choose [Save
Settings] in the 4 tab, then press the m
button.
Register the settings.
● Press the qr buttons or turn the  dial to
choose the destination, then press the m
button.
• To change part of the pre-registered settings (except the shooting
mode), choose
or
and change the settings, then repeat Steps 2–
3. These settings will not be reflected in other Shooting modes.
• To return contents registered to
or
to the default settings, turn
the mode dial to
or
, then choose [Reset All] (p. 53).
102
Changing the Color and Shooting
You can change the look of an image when shooting. However, depending on
shooting conditions the image may become coarse, or the colors may not
come out as expected.
Color Accent
You can choose to retain a single color and change the rest to black and white
in a composition.
Choose T.
● Follow Steps 1 – 2 on p. 63 to choose T.
Press the l button.
Y
P
O
X The unchanged image and the Color Swap
image will alternately display.
● The color for default settings is green.
Specify the color.
C
Recorded color
● Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the range of colors.
● Press the op buttons or turn the  dial
to change the range of colors to be
retained.
● Choose a negative value to limit the range
of colors. Choose a positive value to
extend the range of colors to similar colors.
● Pressing the l button restores the
shooting screen.
Using the flash may cause unexpected results in this mode.
103
Changing the Color and Shooting
Color Swap
You can swap one color in an image for another when recording it. You can
only swap one color.
Choose Y.
● Follow Steps 1 – 2 on p. 63 to choose Y.
Press the l button.
Y
P
O
X The unchanged image and the Color Swap
image will alternately display.
● The default setting is to change green to
gray.
C
Specify the color to be swapped.
● Position the center frame so it is filled with
the color you want and press the q button.
X The specified color will be recorded.
Specify the target color.
● Position the center frame so it is filled with
the color you want and press the r button.
X The specified color will be recorded.
104
Changing the Color and Shooting
Specify the range of colors to be
swapped.
● Press the op buttons or turn the  dial
to adjust the range of colors to be
changed.
● Choose a negative value to limit the range
of colors. Choose a positive value to
extend the range of colors to similar colors.
● Press the l button to restore the
shooting screen.
Y
P
O
• Using the flash may cause unexpected results in this mode.
• Under some conditions, the image may appear coarse.
C
105
Shooting Stitch Assist Images
Large subjects can be split into several shots that can later be merged
together using the included software on a computer to create a panoramic
image.
Choose x or v.
● Follow Steps 1 – 2 on p. 63 to choose x
or v.
Take the first shot.
X The exposure and white balance will be set
with the first shot.
Y
P
O
Take subsequent shots.
● Overlap part of the first shot when taking
C
the second shot.
● Minor discrepancies in the overlapping
portions will be corrected when the images
are merged.
● Up to 26 shots can be recorded with the
same procedures.
Finish shooting.
● Press the m button.
Merge the images on a computer.
● For details on how to merge the images,
refer to the Software Guide.
• This function is not available when a TV is used as the monitor (p. 82).
• To use AF lock, register AFL to the
106
button (p. 162).
6
Using Various Functions for
Shooting Movies
Y
P
O
This chapter serves as a more advanced version of the “Shooting
Movies” and “Viewing Movies” sections in Chapter 1, and explains how
to use various functions for shooting and viewing movies.
C
• This chapter assumes that the mode dial has been set to E mode. You
can use various functions for shooting movies (pp. 108 – 115), which
differs from shooting movies by pressing the movie button (p. 30).
• Press the 1 button to enter Playback mode before playing back or editing
movies.
Shooting Movies in Modes Other than E
• You can shoot movies by pressing the movie button, however, certain
settings made in the ø and Shooting menus will automatically change
to match settings for shooting movies.
• When the mode dial is set to A, the camera can automatically select all
settings so that you can shoot movies (p. 30).
• When you finish shooting a movie, the settings will return to those before
the movie was shot.
107
Shooting Movies in E Mode
Enter E mode.
● Set the mode switch to E.
Adjust the settings according to
your purposes (pp. 108 – 115).
Shoot.
● Press the movie button.
● To stop shooting the movie, press the
movie button again.
Changing the Movie Mode
Y
P
O
You can choose between four Movie modes.
Choose a Movie mode.
● After pressing the m button, press the
C
op buttons to choose E.
● Press the qr buttons or turn the  dial to
E Standard
Miniature Effect
> Color Accent
z Color Swap
choose a mode, then press the m button.
Normal mode.
You can shoot movies that look like a miniature model (p. 109).
These Shooting modes let you change all colors except the
chosen color to black and white, or exchange the chosen color
for another color, when shooting. See “Changing the Color and
Shooting” (p. 103) for details. You need to choose the color
you wish to leave in or change before shooting the movie.
Under some conditions, colors may not turn out as expected in > and z
modes.
• Pressing the movie button in
mode will record a movie in E.
• Even if you press the movie button when in T or Y, you can shoot
movies with Color Accent (p. 103) or Color Swap (p. 104).
108
Shoot Movies That Look Like a Miniature
Model (Miniature Effect)
You can shoot movies that look like moving miniature models.
You create the miniature model effect by choosing the upper and lower
portions of the scene that will be blurred and the playback speed, which
makes people and objects in the scene move quickly during playback.
Audio will not be recorded.
Choose
.
● Follow the steps for "Changing the Movie
Mode" on p. 108 to choose
.
X A white frame (the area that will not be
blurred) appears on the screen.
Y
P
O
Choose the area to keep in focus.
● Press the l button.
● Move the zoom lever to change the frame
size, and press the op buttons to change
the frame position.
C
Choose a playback speed.
● Press the n button.
● Press the qr buttons or turn the  dial to
choose a playback speed.
● Pressing the m button restores the
shooting screen.
Shoot.
● Press the movie button.
● To stop shooting the movie, press the
movie button again.
109
Shoot Movies That Look Like a Miniature Model (Miniature Effect)
Playback Speeds and Estimated Playback Times (for 1 Min.
Clips)
Speed
Playback Time
12 sec.
6 sec.
3 sec.
• If you press the m button in Step 2, the horizontal/vertical orientation of
the frame will switch, and you can use the qr buttons to change the
frame position when it is displayed vertically.
• Holding the camera vertically will change the orientation of the frame.
• Since you may not achieve the expected results depending on the
shooting conditions, try taking some test shots first.
C
110
Y
P
O
Changing the Image Quality
You can choose between three image quality settings.
Choose the image quality setting.
● After pressing the m button, press the
op buttons to choose
.
Choose an option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m
button.
X The option you set will appear on the screen.
Image Quality Table
Y
P
O
Image Quality
(Recording Pixels/Frame Rate)
Content
1280 x 720 pixels, 30 frames/sec. For shooting high-definition movies.
640 x 480 pixels, 30 frames/sec. For shooting standard quality movies.
C
Since the number of recording pixels is smaller than
320 x 240 pixels, 30 frames/sec. in
, the image quality will appear coarse, but you
can record approximately three times the length.
Estimated Shooting Time
Memory Card
Capacity
Image Quality
4 GB
16 GB
20 min. 43 sec.
1 hr. 24 min. 54 sec.
43 min. 43 sec.
2 hrs. 59 min. 3 sec.
1 hr. 58 min. 19 sec.
8 hrs. 4 min. 30 sec.
• Based on Canon’s testing standards.
• Recording will automatically stop when the clip file size reaches 4 GB, or when the
recording time reaches 29 minutes and 59 seconds when shooting in
, and
approximately 1 hour when shooting in
or
.
• Recording may stop even if the maximum clip length has not been reached on some
memory cards. SD Speed Class 4 or higher memory cards are recommended.
In
and
when the recording pixel setting for still images is set to
,
a gray frame will appear around the area that can be shot as a still image.
111
Taking Still Images while Shooting a Movie
You can shoot still images while shooting a movie.
Focus while shooting a movie.
● Make sure that 4 appears on the screen
and press the shutter button halfway.
X The focus and exposure will readjust (the
camera will not beep).
X The movie will continue shooting.
Shoot.
● Press the shutter button fully.
X The still image will be recorded.
• While shooting in
(p. 74).
Y
P
O
, the recording pixel setting for still images is
• While shooting a movie in
or
, you can take a still image at the
recording pixel setting you set for still images (p. 74). However, if the
recording pixel setting is
and you shoot a still image in
, the image
will be recorded at a setting of
.
C
• The shutter sound and black screen that occur when shooting a still
image will be recorded in the movie.
• The flash will not fire.
• The shooting date and time cannot be recorded in the lower right corner
of the image.
• The ISO speed will switch to
.
• i-Contrast (p. 98) is not available.
• If shooting still images fills the internal memory, the movie may stop
recording.
• You cannot take a still image while shooting a movie in
.
• In > or z, you can shoot movies with Color Accent (p. 103) or Color
Swap (p. 104).
112
AE Lock/Exposure Shift
What if 4 changes and you can’t take a still image?
You may not be able to take still images when the writing speed to the memory
card is slow, or when there is insufficient internal memory.
• 4 (blinking): Processing recorded image. You can shoot when the icon stops
blinking.
•
: Still images cannot be taken due to insufficient internal memory.
AE Lock/Exposure Shift
You can lock the exposure or change it in 1/3 steps within a range of ±2 before
or during shooting.
Y
P
O
Lock the exposure.
● Press the o button to lock the exposure.
The exposure shift bar appears.
C
● Press the o button again to release the
lock.
Change the exposure.
● While watching the screen, turn the  dial
to adjust the exposure.
Shoot.
● Press the movie button.
● To stop shooting the movie, press the
movie button again.
113
Sound Settings
Adjusting the Recording Volume
You can manually set the recording volume for shooting movies.
● Press the n button to choose [Movie
Audio] from the 4 tab, then press the m
button.
● Press the op buttons or turn the  dial
to choose [Mic Level], then press the qr
buttons to choose [Manual].
Auto
The recording volume is
automatically adjusted to reduce
sound distortion.
Manual
After pressing the p button, press
the qr buttons to set the sound
recording level (recording volume).
Y
P
O
Using the Wind Filter
C
Wind Filter suppresses noise when the wind is strong. However, unnatural
sound may result when used to record in locations with no wind.
● Press the n button to choose [Movie
Audio] from the 4 tab, then press the m
button.
● Press the op buttons or turn the  dial
to choose [Wind Filter], then press the qr
buttons to choose [On].
114
Other Shooting Functions
The following functions can be used in the same way as for still images.
Functions marked with a * can be used in the same way as for still images
when in
, > or z.
• Zooming in More Closely On Subjects
- The optical and digital zooms (p. 58) are available in E.
- Only the optical zoom is available in > and z.
- Neither the optical nor digital zooms are available while shooting in
to set the optical zoom before shooting.
- The sound of the zoom will be recorded.
• Using the Self-Timer (p. 61)*
• Shooting Close-ups (Macro) (p. 73)*
Macro shooting is not available in
.
• Adjusting the White Balance (p. 77)
• Changing the Tone of an Image (My Colors) (p. 79)
• Using the Self-Timer to Prevent Camera Shake (p. 80)*
• Customizing the Self-Timer (p. 81)*
The number of shots cannot be changed.
• Shooting Using a TV Monitor (p. 82)*
• Shooting with the AF Lock (p. 87)*
• Shooting in Manual Focus Mode (p. 89)*
• Turning Off the AF Assist Beam (p. 158)*
• Customizing Display Information (p. 160)*
• Changing the IS-Mode Settings (p. 161)*
You can switch between [Continuous] and [Off].
• Registering Functions to the
Button (p. 162)*
C
. Be sure
Y
P
O
115
Playback Functions
The following functions can be used in the same way as for still images.
•
•
•
•
•
•
•
•
•
•
•
•
Erasing Images (p. 29)
Quickly Searching Images (p. 120)
Viewing Images in Filtered Playback (p. 121)
Viewing Slideshows (p. 123)
Changing Image Transitions (p. 126)
Viewing Images on a TV (p. 127)
Viewing Images on a High-Definition TV (p. 128)
Protecting Images (p. 129)
Erasing Images (p. 132)
Tagging Images as Favorites (p. 134)
Organizing Images by Category (My Category) (p. 135)
Rotating Images (p. 137)
Y
P
O
Summary of Movie Control Panel in “Viewing Movies”
(p. 32)
Exit
Playback
C
Slow motion playback (you can use the qr buttons or turn the  dial to adjust
the speed. Sound will not play back.)
Display the first frame
Previous frame (Rewind if you hold down the m button.)
Next frame (Fast forward if you hold down the m button.)
Display the last frame
*
Edit (p. 117)
Appears when connected to a PictBridge compliant printer (p. 144).
Refer to the Personal Printing Guide for details.
116
Editing
You can trim the beginnings and ends of recorded movies.
Choose *.
● Follow Steps 1 – 3 on p. 32 to choose *,
then press the m button.
X The movie editing panel and the movie
editing bar will appear.
Movie Editing Panel
Set the editing range.
● Press the op buttons and choose
or
.
Y
P
O
● Press the qr buttons or turn the  dial to
Movie Editing Bar
C
move .
will display at a point where
you can edit the movie. If you choose
,
you can trim the beginning of the movie
from
. If you choose
, you can trim
the end of the movie from
.
X Even if you move
to a point other than a
, only the portion from the nearest
to
the left will be trimmed when
is chosen.
Only the portion from the nearest
to the
right will be trimmed when
is chosen.
X The section indicated with
will be the
section of the movie that remains after
editing.
Check the edited movie.
● Press the op buttons to choose
(Play), then press the m button. The
edited movie will play.
● To edit the movie again, repeat Step 2.
117
Editing
● To cancel editing, press the op buttons,
and choose
. After pressing the m
button, press the qr buttons or turn the
 dial to choose [OK], then press the m
button again.
Save the edited movie.
● Press the op buttons to choose
, then
press the m button.
● Press the opqr buttons, or turn the Â
dial to choose [New File], then press the m
button.
Y
P
O
X The movie will be saved as a new file.
• When [Overwrite] is chosen in Step 4, the unedited movie is overwritten
with the edited movie, erasing the original.
• When there is not enough space left on the memory card, only
[Overwrite] can be chosen.
C
• If the battery is depleted partway through editing, the edited movie clips
may not be saved.
• When editing movies, you should use a fully charged battery, or an AC
adapter kit (sold separately) (p. 39).
118
7
Using Various Playback and
Editing Functions
Y
P
O
This chapter explains various ways to play back and edit images.
• Press the 1 button to enter Playback mode before operating the camera.
• It may not be possible to play back or edit images that have been edited
on a computer, had their file name changed, or have been taken on a
different camera.
C
• The edit function (pp. 138 – 142) cannot be used if the memory card
does not have free space available.
119
Quickly Searching Images
Searching Images Using Index Display
Displaying multiple images at the same time lets you quickly find the image
you want.
Move the zoom lever toward g.
X Images will display in an index.
● The number of images increases each
time you move the lever toward g.
● The number of images decreases each
time you move the lever toward k.
Choose an image.
Y
P
O
● Turn the  dial to switch images.
● Press the opqr buttons to choose an
image.
X An orange frame appears on the chosen
image.
● Press the m button to display the chosen
image by itself.
C
Searching Images Using the Control Dial
Turning the control dial will display images in a line letting you quickly search
them. You can also jump by the shooting date (Scroll Display).
Choose an image.
● If you set the camera to single image
playback and turn the  dial quickly, the
images will display as shown on the left.
Turn the  dial to choose an image.
● Pressing the m button restores single
image playback.
● If you press the op buttons during Scroll
Display, you can search images by the
shooting date.
To turn off this effect, press the n button to choose [Scroll Display] in
the 1 tab, then choose [Off].
120
Viewing Images in Filtered Playback
When there are many images on the memory card, you can filter and display
them by a specified filter. You can also protect (p. 129) or delete (p. 132) all
images at once while filtered.
Jump to Favorites
Displays images tagged as favorites (p. 134).
Jump Shot Date
Displays the images shot on a specified date.
Jump to My Category
Displays the images of a specified category (p. 135).
Jump to Still/Movie
Displays only still images or movies.
Jump 10 Images
Jumps over 10 images at a time.
Jump 100 Images
Jumps over 100 images at a time.
Search by
,
,
and
Y
P
O
Choose a target filter.
● In single image playback, press the d
Target Filters
C
button, then press the op buttons to
choose a jump method.
● In
,
or
, press the qr buttons to
choose a filter. Turning the  dial will
display only images that match the filter of
the chosen target image.
● Press the l button to switch between
Information Display and No Information
Display.
● Pressing the n button restores single
image playback.
View the filtered images.
● Pressing the m button will start filtered
playback, and the jump method and a
yellow frame will appear.
● If you press the qr buttons or turn the Â
dial, the chosen target images will display.
● If you press the d button, [Filtered
playback settings cleared] appears.
Pressing the m button cancels filtered
playback.
121
Viewing Images in Filtered Playback
What if you can’t choose a filter?
Filters that do not have any corresponding images cannot be chosen.
Filtered playback
In filtered playback (Step 2), you can view filtered images with “Quickly Searching
Images” (p. 120), “Viewing Slideshows” (p. 123), and “Magnifying Images”
(p. 125). You can process all filtered images at once while performing operations
in “Protecting Images” (p. 129), “Erasing Images” (p. 132), or “Printing from the
Print List (DPOF)” (p. 147), by choosing all of the filtered images.
However, if you change the category (p. 135), or edit an image and save it as a
new image (p. 138), a message will appear, and filtered playback will cancel.
Jump by
and
Y
P
O
Images
● In single image playback, press the d
button, then press the op buttons to
choose a jump method.
● If you press the qr buttons, the display
C
will advance to the image that is the
chosen number of images away.
● Pressing the n button restores single
122
image playback.
Viewing Slideshows
You can automatically play back images recorded to a memory card.
Choose [Slideshow].
● Press the n button to choose
[Slideshow] from the 1 tab, then press the
m button.
Make the setting.
● Press the op buttons or turn the  dial
to choose an item, then press the qr
buttons to adjust the setting.
C
Y
P
O
Repeat
Repeats playback of images
Play Time
Display time for each image
Effect
Transition effects when switching
between images
Choose [Start].
● Press the op buttons or turn the  dial
to choose [Start], then press the m button.
X The slideshow will start a few seconds
after [Loading image...] displays.
● You can pause/restart a slideshow by
pressing the m button again.
● Press the n button to stop the
slideshow.
• If you press the qr buttons or turn the  dial during playback, the
image will switch. If you keep the qr buttons pressed, you can fastforward through images.
• The power saving function (p. 52) does not work during slideshows.
• You cannot change [Play Time] if [Bubble] is chosen in [Effect].
• You can also start a slideshow in single image playback by pressing and
holding the m button and immediately pressing the
button.
123
Checking the Focus
You can magnify the area of a recorded image that was inside the AF Frame,
or the area of a face that was detected, to check the focus.
Press the l button to switch to
the focus check display (p. 47).
X A white frame will appear where the AF
frame or face was when the focus was set.
X A gray frame will appear on a face
detected during playback.
X The area within the orange frame appears
magnified.
Y
P
O
Switch frames.
● Move the zoom lever toward k once.
X The screen shown to the left will appear.
● Press the m button to move to a different
C
frame when multiple frames appear.
Change the magnification level or
location.
● Use the zoom lever to change the display
size, and the opqr buttons to change
the display position while checking the
focus.
● Pressing the n button resets the
display to Step 1.
124
Magnifying Images
Move the zoom lever toward k.
● The display will zoom in on the image. If
you continue to hold the zoom lever, it will
zoom in up to a maximum factor of 10x.
● If you press the opqr buttons, you can
move the location of the displayed area.
● Move the zoom lever toward g to zoom
out, or continue to hold it to return to single
image playback.
● If you turn the  dial, you can switch
Approximate Location of
Displayed Area
images while zoomed.
Y
P
O
You can return to single image playback immediately by pressing the
n button while the image is magnified.
C
Displaying Various Images (Smart Shuffle)
The camera will choose four images based on the displayed image.
If you choose one of those images, the camera will choose four more images
letting you enjoy the playing back of images in an unexpected order.
This will work best if you take many shots of various scenes.
Choose [Smart Shuffle].
● Press the n button to choose [Smart
Shuffle] from the 1 tab, then press the m
button.
X Four images will appear as possibilities.
125
Changing Image Transitions
Choose an image.
● Press the opqr buttons to choose the
image you want to view next.
X The chosen image will be displayed in the
middle, and the next four possibilities will
appear.
● Pressing the m button will display the
middle image at full size. Press the m
button again to restore the original display.
You can also use the zoom lever.
● Pressing the n button restores single
Y
P
O
image playback.
• Only still images shot with this camera will play back in Smart Shuffle.
• [Smart Shuffle] is not available in the following situations:
- If there are less than 50 images taken with this camera on the memory card.
C
- If you play back images not supported by Smart Shuffle.
- During filtered playback.
Changing Image Transitions
You can choose from three transition effects when switching between images
in single image playback.
Choose [Transition].
● Press the n button to choose
[Transition] in the 1 tab, then press the
qr buttons to choose a transition effect.
126
Viewing Images on a TV
Using the supplied stereo AV cable (p. 2), you can connect the camera to a
TV to view images you have shot.
Turn off the camera and TV.
Connect the camera to the TV.
● Open the camera’s terminal cover and fully
insert the cable plug into the camera’s
terminal.
Yellow
Yellow
White Red
Red
White
C
● Insert the cable plug fully into the video
input terminals as shown in the illustration.
Y
P
O
Turn on the TV and switch it to the
input the cable is connected to.
Turn on the camera.
● Press the 1 button to turn on the camera.
X The image will appear on the TV (nothing
will appear on the screen of the camera).
● After you finish, turn off the camera and
TV, and unplug the cable.
What if the images don’t display correctly on the TV?
Images will not display correctly if the camera’s video output setting (NTSC/PAL)
does not match the TV system. Press the n button, choose the 3 tab and
[Video System] to switch to the correct video system.
127
Viewing Images on a High-Definition TV
Use the separately sold HDMI Cable HTC-100 to connect the camera to a
high-definition TV for an enhanced viewing experience.
Turn off the camera and TV.
Connect the camera to the TV.
● Open the camera’s terminal cover and fully
insert the cable plug into the camera’s
terminal.
● Fully insert the cable plug into the TV’s
HDMI terminal.
Y
P
O
Display images.
C
● Follow Steps 3 and 4 on p. 127 to display
the images.
Operation sounds will not play when connected to a high-definition TV.
128
Protecting Images
You can protect important images so that they cannot be accidentally erased
with the camera (pp. 29, 132).
Choose a selection method
Choose [Protect].
● Press the n button to choose
[Protect] in the 1 tab, then press the m
button.
Choose a selection method.
● Press the op buttons or turn the  dial
Y
P
O
to choose a selection method, then press
the m button.
● Pressing the n button will restore the
menu screen.
If you format the memory card (pp. 23, 54), protected images will also be
erased.
C
Protected images cannot be erased with the camera’s erase function. To
erase an image, cancel protection settings first.
Choosing Images Individually
Choose [Select].
● Follow Step 2 above to choose [Select],
then press the m button.
Choose images.
● Press the qr buttons or turn the  dial to
choose an image, then press the m button.
X
will appear on the screen.
● Pressing the m button again deselects
the image and
will disappear.
● To choose additional images, repeat the
above procedure.
129
Protecting Images
Protect the image.
● If you press the n button, a
confirmation screen will appear.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
If you switch shooting modes or turn off the power before performing the
operations in Step 3, images will not be protected.
Select Range
Y
P
O
Choose [Select Range].
● Follow Step 2 on p. 129 to choose [Select
Range], then press the m button.
Choose a starting image.
● Press the m button.
C
● Press the qr buttons or turn the  dial to
choose an image, then press the m
button.
Choose an ending image.
● Press the r button to choose [Last image],
then press the m button.
130
Protecting Images
● Press the qr buttons or turn the  dial to
choose an image, then press the m button.
● You cannot choose images before the first
image.
Protect images.
● Press the p button to choose [Protect],
then press the m button.
Y
P
O
Choose images with the  dial
You can also choose the first or last image by turning the  dial when the upper
screen in Steps 2 and 3 is displayed.
C
Choose All Images
Choose [All Images].
● Follow Step 2 on p. 129 to choose [All
Images], then press the m button.
Protect images.
● Press the op buttons or turn the  dial
to choose [Protect], then press the m
button.
You can unlock groups of protected images if you choose [Unlock] in Step
4, while in [Select Range] or Step 2 while in [All Images].
131
Erasing Images
You can choose images and then erase them in groups. Since erased images
cannot be recovered, exercise adequate caution before erasing. Protected
images (p. 129) cannot be erased.
Choose a selection method
Choose [Erase].
● Press the n button to choose [Erase]
in the 1 tab, then press the m button.
Choose a selection method.
Y
P
O
● Press the op buttons or turn the  dial
to choose a selection method, then press
the m button.
● Pressing the n button will restore the
C
menu screen.
Choosing Images Individually
Choose [Select].
● Follow Step 2 above to choose [Select]
and press the m button.
Choose an image.
X If you follow Step 2 on p. 129 to choose
images,
will appear on the screen.
● Pressing the m button again deselects
the image and
will disappear.
● To choose additional images, repeat the
above procedure.
132
Erasing Images
Erase.
● If you press the n button, a
confirmation screen will appear.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
Select Range
Choose [Select Range].
● Follow Step 2 on p. 132 to choose [Select
Range], then press the m button.
Y
P
O
Choose images.
● Follow Steps 2 and 3 on p. 130 to choose
images.
C
Erase.
● Press the p button to choose [Erase],
then press the m button.
Choose All Images
Choose [All Images].
● Follow Step 2 on p. 132 to choose [All
Images], then press the m button.
Erase.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
133
Tagging Images as Favorites
When you tag images as favorites, you can easily categorize just those
images. You can also filter out just those images for viewing, protecting or
erasing (p. 121).
Choose [Favorites].
● Press the n button to choose
[Favorites] in the 1 tab, then press the m
button.
Choose an image.
Y
P
O
● Press the qr buttons or turn the  dial to
choose an image, then press the m
button.
X
will appear on the screen.
● Pressing the m button again untags the
C
image and
disappears.
● To choose additional images, repeat the
above procedure.
Make the setting.
● If you press the n button, a
confirmation screen will appear.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
If you switch Shooting modes or turn off the power before making the
setting in Step 3, images will not be tagged as favorites.
If you use Windows 7 or Windows Vista and transfer tagged images to the
computer, they will be given a star rating of 3 (
) (except for
movies).
134
Organizing Images by Category
(My Category)
You can organize images into categories. You can display the images in a
category in Filtered Playback (p. 121) and process all images at once by
using the functions below.
• Viewing Slideshows (p. 123), Protecting Images (p. 129), Erasing All
Images (p. 132), Choosing Images for Printing (DPOF) (p. 147)
Images are automatically categorized by shooting condition as they are
shot.
: Images with detected faces, or images shot in I mode.
: Images detected as
,
or
in A mode, or images shot in
J or O mode.
: Images shot in
, w, Por t mode.
Y
P
O
Choosing a Selection Method
Choose [My Category].
C
● Press the n button to choose [My
Category] in the 1 tab, then press the m
button.
Choose a selection method.
● Press the op buttons or turn the  dial
to choose a selection method, then press
the m button.
● Pressing the n button will restore the
menu screen.
Choosing Images Individually
Choose [Select].
● Follow Step 2 above to choose [Select],
then press the m button.
135
Organizing Images by Category (My Category)
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image.
Choose a category.
● Press the op buttons to choose a
category, then press the m button.
X
will appear on the screen.
● Pressing the m button again deselects
the image and
will disappear.
● To choose additional images, repeat the
Y
P
O
above procedure.
Make the setting.
● If you press the n button, a
confirmation screen will appear.
● Press the qr buttons or turn the  dial to
C
choose [OK], then press the m button.
If you switch Shooting modes or turn off the power before making the
setting in Step 4, images will not be tagged as My Category.
Select Range
Choose [Select Range].
● Follow Step 2 on p. 135, choose [Select
Range], then press the m button.
Choose images.
● Follow Steps 2 and 3 on p. 130 to choose
images.
136
Rotating Images
Choose a category.
● Press the p button to choose an item,
then press the qr buttons or turn the Â
dial to choose a category.
Choose the setting.
● Press the p button to choose [Select],
then press the m button.
If you choose [Deselect] in Step 4, you can deselect all of the images in
the [Select Range] category.
Y
P
O
Rotating Images
You can change the orientation of an image and save it.
C
Choose [Rotate].
● Press the n button to choose [Rotate]
in the 1 tab, then press the m button.
Rotate the image.
● Press the qr buttons or turn the  dial to
choose an image.
X The image will rotate 90° with each press
of the m button.
● Pressing the n button will restore the
menu screen.
Movies with a resolution of
cannot be rotated.
137
Resizing Images
You can resize images to a lower pixel setting and save the resized image as
a separate file.
Choose [Resize].
● Press the n button to choose
[Resize] in the 1 tab, then press the m
button.
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image, then press the m button.
Y
P
O
Choose an image size.
● Press the qr buttons or turn the  dial to
choose an option, then press the m button.
X The [Save new image?] screen will
appear.
C
Save the new image.
● Press the qr buttons or turn the  dial to
choose [OK] and press the m button.
X The image will be saved as a new file.
Display the new image.
● When you press the n button, the
[Display new image?] screen will appear.
● Press the qr buttons or turn the  dial to
choose [Yes], then press the m button.
X The saved image will be displayed.
• You cannot resize an image to a larger size.
• Images recorded at a pixel setting of
3 cannot be edited.
138
(p. 74), or saved as
in Step
Trimming
You can cut out a portion of a recorded image and save it as a new image file.
Choose [Trimming].
● Press the n button to choose
[Trimming] in the 1 tab, then press the m
button.
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image, then press the m button.
Trimming Area
Adjust the trimming area.
X A frame will appear around the portion of
Y
P
O
the image to be trimmed.
X The original image will display in the upper
C
Trimming Area Display
Recorded pixels after
trimming
left and the trimmed image will display in
the lower right.
● If you move the zoom lever to the left or
right, you can change the frame size.
● If you press the opqr buttons, you can
move the frame.
● If you press the l button, you can
change the frame orientation.
● In an image with detected faces, gray
frames appear around the faces located in
the upper left image. The frames can be
used for trimming. You can switch between
frames by turning the  dial.
● Press the m button.
Save as a new image and display.
● Follow Steps 4 and 5 on p. 138.
• Images recorded at a pixel setting of
or
(p. 75), or images
resized to
(p. 138) cannot be edited.
• The width and height ratio of an image that can be trimmed is fixed at 4:3.
• The number of recorded pixels in a trimmed image will be smaller than
before trimming.
139
Adding Effects with the My Colors Function
You can change the color of an image and save it as a separate image. Refer
to p. 79 for details on each menu item.
Choose [My Colors].
● Press the n button to choose [My
Colors] in the 1 tab, then press the m
button.
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image, then press the m
button.
Y
P
O
Choose a menu option.
● Press the qr buttons or turn the  dial to
choose an option, then press the m
button.
C
X The image will appear with the chosen
effect.
Save as a new image and display.
● Follow Steps 4 and 5 on p. 138.
If you repeatedly change the color of the same image, the quality will
gradually deteriorate and you may not achieve the expected color.
The color of images changed with this function may vary from those
recorded with the My Colors function (p. 79).
140
Correcting the Brightness (i-Contrast)
The camera can detect areas in an image, such as faces or backgrounds, that
are too dark and automatically adjust them to the optimum brightness. Also,
when the overall image is lacking in contrast, the camera will automatically
correct the image for a sharper impression. You can choose from four levels
of correction, and save the image as a new file.
Choose [i-Contrast].
● Press the n button to choose [iContrast] in the 1 tab, then press the m
button.
Choose an image.
Y
P
O
● Press the qr buttons or turn the  dial to
choose an image, then press the m
button.
Choose a menu item.
C
● Press the qr buttons or turn the  dial to
choose an option, then press the m
button.
Save as a new image and display.
● Follow Steps 4 and 5 on p. 138.
• Under some conditions, the image may appear coarse or not be
corrected properly.
• Repeatedly adjusting the same image may cause it to become coarse.
What if the image wasn’t corrected by the [Auto] option as
well as you would like?
Choose [Low], [Medium] or [High] and adjust the image.
141
Correcting the Red-Eye Effect
You can automatically correct red eyes in images and save them as new files.
Choose [Red-Eye Correction].
● Press the n button to choose [RedEye Correction] in the 1 tab, then press
the m button.
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image.
Correct the image.
Y
P
O
● Press the m button.
X Red-eye detected by the camera will be
corrected and a frame will appear around
the corrected portion.
● You can magnify or reduce the size of the
C
image using the procedures in “Magnifying
Images” (p. 125).
Save as a new image and display.
● Press the opqr buttons or turn the Â
dial to choose [New File], then press the
m button.
X The image will be saved as a new file.
● Follow Step 5 on p. 138.
• Some images may not be corrected properly.
• When [Overwrite] in Step 4 is chosen, the uncorrected image is
overwritten with the corrected data, erasing the original image.
• Protected images cannot be overwritten.
142
8
Printing
This chapter explains how to choose images for printing, and print
using a Canon-brand PictBridge compliant printer (sold separately)
(p. 41).
Y
P
O
Please also refer to the Personal Printing Guide.
Canon-Brand PictBridge Compliant Printers
C
143
Printing Images
You can easily print the pictures you take by connecting the camera to a
PictBridge compliant printer (sold separately) using the supplied interface
cable (p. 2).
Turn off the camera and printer.
Connect the camera to the printer.
● Open the cover and insert the small plug of
the included interface cable (p. 2) firmly
into the camera terminal in the direction
shown.
● Insert the interface cable’s large plug into
Y
P
O
the printer. For connection details, refer to
the user guide provided with the printer.
Turn on the printer.
C
Turn on the camera.
● Press the 1 button to turn on the camera.
X
will appear on the screen.
144
Printing Images
Choose an image to print.
● Press the qr buttons or turn the  dial to
choose an image.
Print images.
● Press the c button.
X Printing will start.
● If you want to print additional images,
repeat Steps 5 and 6 after printing has
completed.
Y
P
O
● After printing has completed, turn off the
camera and printer, and unplug the
interface cable.
• Refer to the Personal Printing Guide for details on printing.
• Refer to p. 41 for Canon-brand Pictbridge compliant printers.
C
• Index printing (p. 147) is not available on certain Canon-brand
PictBridge compliant printers (sold separately).
145
Printing from the Print List (DPOF)
You can add images to the print list (DPOF) directly after shooting or during
playback by pressing the c button.
These selection methods comply with the DPOF (Digital Print Order Format)
standards.
Choose an image.
● Press the qr buttons or turn the  dial to
choose an image.
Press the c button (movies will be
excluded).
Add images to the print list.
Y
P
O
● Press the op buttons to choose the
number of prints, then press the qr
buttons or turn the  dial to choose [Add]
and press the m button.
● To cancel adding images, repeat Steps 1
C
and 2, and press the qr buttons or turn
the  dial to choose [Remove], then
press the m button.
You cannot add images when the camera is connected to the printer.
146
Choosing Images for Printing (DPOF)
You can choose up to 998 images on a memory card for printing and specify
settings such as the number of copies so that they can be printed together
(p. 150) or processed at a photo developer service. These selection methods
comply with the DPOF (Digital Print Order Format) standards.
Print Settings
You can set the print type, date and file number. These settings apply to all
images chosen for printing.
Choose [Print Settings].
● Press the n button to choose [Print
Settings] in the 2 tab, then press the m
button.
Y
P
O
Adjust the settings.
● Press the op buttons or turn the  dial
C
Standard
Print Type
Date
File No.
Clear DPOF
data
to choose a menu item, then press the qr
buttons to choose an option.
● Pressing the n button accepts the
settings and restores the menu screen.
Prints one image per page.
Index
Prints several reduced size images per page.
Both
Prints both standard and index formats.
On
Off
On
Off
On
Off
Prints the shooting date.
—
Prints the file number.
—
Removes all print settings after printing.
—
• Some printers or photo developer services may not be able to reflect all
of the settings in the prints.
•
may appear when using a memory card with print settings set by a
different camera. These settings will be overwritten with those set by
your camera.
• If [Date] is set to [On], some printers may print the date twice.
147
Choosing Images for Printing (DPOF)
• With [Index] chosen, the [Date] and [File No.] options cannot be set to
[On] at the same time.
• The date will be printed in the style set in the [Date/Time] function in the
3 tab (p. 20).
• Movies cannot be chosen.
Choosing the Number of Copies
Choose [Select Images & Qty.].
● Press the n button to choose [Select
Images & Qty.] in the 2 tab, then press
the m button.
Y
P
O
Choose an image.
● Press the qr buttons or turn the  dial to
C
choose an image, then press the m
button.
X You will be able to set the number of print
copies.
● If you choose images in [Index],
appears on the screen. Pressing the m
button again will deselect the image and
will disappear.
Set the number of prints.
● Press the op buttons or turn the  dial
to set the number of prints (maximum 99).
● Repeat Steps 2 and 3 to choose other
images and the number of prints for each.
● You cannot set the number of copies for
index prints. You can only choose which
images to print (as shown in Step 2).
● Pressing the n button accepts the
settings and restores the menu screen.
148
Choosing Images for Printing (DPOF)
Select Range
Choose [Select Range].
● In Step 1 on p. 148, choose [Select
Range], then press the m button.
● Follow Steps 2 and 3 on p. 130 to choose
images.
Make print settings.
● Press the op buttons to choose [Order],
then press the m button.
Y
P
O
Set All Images to Print Once
C
Choose [Select All Images].
● In Step 1 on p. 148, choose [Select All
Images], then press the m button.
Make print settings.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
Clearing All Selections
Choose [Clear All Selections].
● In Step 1 on p. 148, choose [Clear All
Selections], then press the m button.
149
Print Added Images
All selections will be cleared.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button.
Print Added Images
You can print images added to the print list by connecting the camera to a
PictBridge compliant printer (pp. 146 – 149).
Number of copies to print
Y
P
O
Connect the camera to the printer.
● Follow Steps 1 to 4 on p. 144.
Print.
● Press the op buttons to choose [Print
C
now], then press the m button.
X Printing will start.
● If you stop the printer during printing and
150
start again, it will start from the next print.
9
Customizing Camera Settings
You can customize various settings to suit your shooting preferences.
The first part of this chapter explains convenient and commonly used
functions.
Y
P
O
The latter part explains how to change shooting and playback settings
to suit your purposes.
C
151
Changing Camera Settings
You can customize convenient and commonly used functions from the 3 tab
(p. 49).
Changing Sounds
You can change each of the camera’s operation sounds.
● Choose [Sound Options], then press the
m button.
● Press the op buttons or turn the  dial
to choose an option.
● Press the qr buttons to choose an option.
Y
P
O
1
Preset sounds
(cannot be modified)
2
Preset sounds
You can use the included software to
change the sounds (p. 2).
Turning Off Hints & Tips
C
When you choose an item in the ø menu (p. 48) or MENU (p. 49), a
description of the function (hints and tips) is displayed. You can turn off this
function.
● Choose [Hints & Tips], then press the qr
buttons to choose [Off].
152
Changing Camera Settings
Changing the Start-up Screen
You can change the start-up screen that appears when you turn on the
camera.
● Choose [Start-up Image], then press the
m button.
● Press the qr buttons or turn the  dial to
choose an option.
No start-up image
1
Preset images
(cannot be modified)
Preset images
You can set recorded images, and use the
included software to change the images.
Y
P
O
2
Registering Recorded Images as the Start-up
Screen
When you press the 1 button and set the camera to Playback mode, you can
register an image.
C
● Choose [Start-up Image], then press the
m button.
● Press the qr buttons or turn the  dial to
choose [2], then press the m button.
● Press the qr buttons or turn the  dial to
choose an image, then press the m
button.
● Press the qr buttons or turn the  dial to
choose [OK], then press the m button to
complete registration.
Any previously registered start-up image will be overwritten when
registering a new start-up image.
153
Changing Camera Settings
Register the start-up image or sounds with the included
software
The dedicated operation sounds and start-up images on the included software
can be registered to the camera. Refer to the Software Guide for details.
Changing the File Number Assignment
Images you shoot are automatically assigned file numbers in the order they
were taken, from 0001 – 9999, and saved to folders of up to 2,000 images.
You can change the file number assignment.
● Choose [File Numbering], then press the
qr buttons to choose an option.
C
Y
P
O
Continuous
Even if you shoot using a new
memory card, the file numbers
are assigned consecutively until
an image with the number 9999
is taken/saved.
Auto Reset
If you replace the memory card
with a new one, or a new folder
is created, file numbering
begins with 0001 again.
• If you use a memory card already containing images, the newly assigned
file numbers may continue the existing numbering for both [Continuous]
and [Auto Reset]. If you want to start over with file number 0001, format
the memory card before use (p. 23).
• Refer to the Software Guide for information regarding folder structure or
image types.
154
Changing Camera Settings
Creating Folders by Shooting Date
Images are saved into folders created each month, however, you can also
create folders by shooting date.
● Choose [Create Folder], then press the
qr buttons to choose [Daily].
● Images will be saved into folders created
on each shooting date.
Changing the Lens Retract Time
Y
P
O
For safety reasons, the lens retracts about 1 minute after pressing the 1
button when in a Shooting mode (p. 28). If you want the lens to retract
immediately when you press the 1 button, set the retract time to [0 sec.].
● Choose [Lens Retract], then press the
C
qr buttons to choose [0 sec.].
Turning Off the Power Saving Function
You can set the power saving function (p. 52) to [Off]. Setting it to [On] is
recommended to save battery power.
● Choose [Power Saving], then press the m
button.
● Press the op buttons or turn the  dial to
choose [Auto Power Down], then press the
qr buttons to choose [Off].
● If you set the power saving function to
[Off], be sure to turn the camera off after
use.
155
Changing Camera Settings
Setting the Screen Shut-Off Time
You can adjust the time the screen takes to shut off automatically (p. 52). This
also works when [Auto Power Down] is set to [Off].
● Choose [Power Saving], then press the m
button.
● Press the op buttons or turn the  dial
to choose [Display Off], then press the qr
buttons to choose a time.
● In order to save battery power, you should
choose less than [1 min.].
Y
P
O
Using the World Clock
When travelling abroad, you can record images with local dates and times
simply by switching the time zone setting. If you pre-register the destination
time zones, you can enjoy the convenience of not having to switch the Date/
Time settings.
C
Set the home time zone.
● Choose [Time Zone], then press the m
button.
● When setting this for the first time, check
the information that displays on the screen
at the left, then press the m button.
● Press the qr buttons or turn the  dial to
choose the home time zone.
● To set daylight saving time (adds 1 hour),
press the op buttons to choose
● Press the m button.
156
.
Changing Camera Settings
Set the world time zone.
● Press the op buttons or turn the  dial
to choose [
button.
World], then press the m
● Press the qr buttons or turn the  dial to
choose the destination time zone.
● You can also set the daylight saving time
as in Step 1.
● Press the m button.
Choose the world time zone.
Y
P
O
● Press the op buttons or turn the  dial
to choose
button.
X
C
, then press the n
will appear on the shooting screen
(p. 179).
If you change the date or time in the
setting (p. 20), your [
time and date will automatically change.
Home]
Changing Distance Units
You can change the distance units that display in the zoom bar (p. 25) and
the MF indicator (p. 89) from m/cm to ft/in.
● Choose [Distance Units], then press the
qr buttons to choose [ft/in].
157
Changing Shooting Function Settings
If you set the mode dial to G, you can change the settings in the 4 tab
(p. 49).
Before attempting to shoot using a function explained in this chapter in
modes other than G mode, check if the function is available in those
modes (pp. 182 – 185).
Switching the Focus Setting
The camera focuses on whatever it is aimed at even when the shutter button
is not pressed. However, you can set it so that the camera only focuses when
the shutter button is pressed halfway.
● Choose [Continuous AF], then press the
Y
P
O
qr buttons to choose [Off].
C
On
Since the camera focuses continuously
until you press the shutter button
halfway, it allows you to shoot without
missing photo opportunities.
Off
The camera does not focus
continuously, thereby conserving
battery power.
Turning Off the AF Assist Beam
The lamp will automatically light to assist focusing in low light conditions when
you press the shutter button halfway. You can turn off the lamp.
● Choose [AF-assist Beam], then press the
qr buttons to choose [Off].
158
Changing Shooting Function Settings
Changing the Flash Timing
You can change the timing of the flash and shutter.
● Choose [Flash Control], then press the m
button.
● Press the op buttons or turn the  dial
to choose [Shutter Sync.], then press the
qr buttons to choose a setting.
1stThe flash fires right after the shutter
curtain opens.
2ndThe flash fires right before the shutter
curtain closes.
Y
P
O
Turning Off the Red-Eye Reduction Function
The red-eye reduction lamp lights in order to reduce the red-eye effect that
occurs when shooting in dark conditions with the flash. You can turn off this
function.
C
● Choose [Flash Control], then press the m
button.
● Press the op buttons or turn the  dial
to choose [Red-Eye Lamp], then press the
qr buttons to choose [Off].
Changing the Image Display Time Right After
Shooting
You can change the length of time the images display right after shooting.
● Choose [Review], then press the qr
buttons to choose an option.
2 – 10 sec.
Displays images for the set time.
Hold
The image displays until you press
the shutter button halfway.
Off
Images will not display.
159
Changing Shooting Function Settings
Changing the Way the Image Displays Right After
Shooting
You can change the way the image displays right after shooting.
● Choose [Review Info], then press the qr
buttons to choose an option.
Off
Displays the image only.
Detailed
Displays detailed information
(p. 181).
The area inside the AF frame is
magnified, allowing you to check
Focus Check the focus. The procedure is the
same as in “Checking the Focus”
(p. 124).
Y
P
O
Customizing Display Information
You can change which information is displayed by switching between custom
displays with each press of the l button.
C
● Choose [Custom Display], then press the
m button.
● Press the opqr buttons or turn the Â
dial to choose an item, then press the m
button.
will appear on items that
display.
● Press the opqr buttons or turn the Â
dial to choose
,
,
, or
, then
press the m button, and the l button
to change the custom display settings.
Custom display items with
will not
display when the l button is pressed.
Also,
cannot be set for the current
custom display while making settings.
X Items with
160
will display.
Changing Shooting Function Settings
Shooting Info
Displays shooting information
(p. 179).
Grid Lines
A grid overlays the screen.
3:2 Guide
Gray bars will appear on the
top and bottom of the screen.
This area will not print when
printing on paper with a 3:2
aspect ratio.
Histogram
A histogram (p. 47) appears in
Shooting modes G, M, B,
D.
If you press the shutter button halfway and return to the shooting screen
from the custom display settings screen, the settings will not be saved.
Y
P
O
• Gray items can also be set, however, they may not appear depending on
the Shooting mode.
• Grid lines will not be recorded on the image.
• [3:2 Guide] is not available in
.
• The gray areas displayed with [3:2 Guide] are the areas that will not be
printed. The actual image recorded will include the portion in the gray areas.
C
Changing the IS-Mode Settings
● Choose [IS Mode], then press the qr
buttons to choose an option.
Continuous
Image stabilization is always on.
You can confirm the effects
directly on the display, which
makes it easier to check the
composition or focus. When
shooting movies, the camera also
reduces strong camera shake, for
example when walking (Dynamic
mode).
Shoot Only*
Image stabilization is only active
at the moment of shooting.
Panning*
Image stabilization only counters
up and down motion. This option
is recommended for shooting
objects moving horizontally.
* Setting changes to [Continuous] when
shooting movies.
161
Changing Shooting Function Settings
• If camera shake is too strong, attach the camera to a tripod. You should
also set the IS Mode to [Off] when the camera is attached to a tripod.
• When using [Panning], hold the camera horizontally to shoot. Image
stabilization does not work when the camera is held vertically.
When shooting movies, if you press the zoom lever toward j and zoom
out, the effect increases.
Registering Functions to the
Button
● Choose [Set Shortcut button], then press
the m button.
Y
P
O
● Press the opqr buttons or turn the Â
dial to choose the functions to register,
then press the m button.
● Pressing the
button will call up the
registered function.
• Choose
C
if you want to return the button to default settings.
• When this
symbol is shown on the bottom right of an icon, the
function cannot be used in the current Shooting mode or function setting.
• In
, each press of the
button records white balance data (p. 77),
and the white balance settings change to
.
• In %, each press of the
button will adjust and lock the focus, and
% will appear on the screen.
• If you press the
button in
, both the screen and viewfinder
displays will turn off. Try one of the following to restore the displays:
•
•
•
•
162
Press any button other than the power button
Change the camera’s vertical or horizontal orientation
Open and close the screen
Raise and lower the flash
Registering Commonly Used Shooting
Menus (My Menu)
You can register up to 5 items from commonly used shooting menus to the
tab, letting you quickly access these items from a single screen.
Choose [My Menu settings].
● Choose [My Menu settings] in the
tab,
then press the m button.
Choose the menu items to register.
Y
P
O
● Press the op buttons or turn the  dial
to choose [Select items], then press the
m button.
● Press the op buttons or turn the  dial
C
to choose a menu to register (up to 5), then
press the m button.
X
will appear.
● To cancel registration, press the m
button, and
will disappear.
● Press the n button.
Change the order in which menu
items are displayed.
● Press the op buttons or turn the  dial
to choose [Sort], then press the m button.
● Press the op buttons or turn the  dial
to choose the menu item you want to move,
then press the m button.
● Press the op buttons or turn the  dial
to change the order, then press the m
button.
● Press the n button.
163
Changing Playback Function Settings
• Gray items in Step 2 can also be set, however, they may not be available
depending on the Shooting mode.
• Choose [Set default view] and press the qr buttons to choose [Yes]. My
Menu can now be displayed by pressing the n button when in a
Shooting mode.
Changing Playback Function Settings
You can adjust the settings in the 1 tab by pressing the 1 button (p. 49).
Choosing the Image that First Displays in
Playback
Y
P
O
● Choose [Resume], then press the qr
buttons to choose an option.
C
164
Last seen
Resumes with the image last
viewed.
Last shot
Resumes with the most
recently shot image.
10
Useful Information
This chapter introduces how to use separately sold accessories
(p. 39), troubleshooting tips, and contains lists of functions and items
Y
P
O
that appear on the screen.
C
165
Using Household Power
If you use AC Adapter Kit ACK-DC50 (sold separately), you can use the
camera without worrying about how much charge is left in the battery.
Turn off the camera.
Plug the cord into the coupler.
● Fully insert the plug into the coupler.
Terminals
Y
P
O
Insert the coupler.
● Follow Step 2 on p. 17 to open the cover,
then insert the coupler as shown until it
locks into place with a click.
C
● Close the cover (
), and press downward
as ( ) you slide it until it clicks into place
( ).
Cord
Connect the power cord.
● Connect the power cord to the compact
power adapter, then plug the other end into
a power outlet.
● Turn the camera on to use it.
● After you finish, turn off the camera and
unplug the power cord from the power outlet.
166
Using the Lens Hood (Sold Separately)
Do not unplug the plug or power cord with the camera turned on. This
could erase images you have taken or damage the camera.
Using the Lens Hood (Sold Separately)
When shooting a wide-angle photo that is backlit without using a flash, we
recommend attaching Lens Hood LH-DC60 to reduce the amount of
extraneous light entering the lens.
Attach the hood.
● Align the notch (
) on the lens hood with
the mark on the camera ( ), and turn the
lens hood in the direction of the arrow until
locked.
Y
P
O
● To remove the lens hood, turn it in the
C
opposite direction.
● When not in use, align the notch (
) on
the hood with the mark on the camera
( ), and turn the hood in the direction of
the arrow until locked as shown.
If you use the built-in flash with the hood attached, portions of the image
may appear darker.
167
Using an Externally Mounted Flash (Sold Separately)
You can make your flash photography even better with the use of a Speedlite
EX series flash (sold separately).
• You should set the white balance to h.
• Please also read the Speedlite series manual included with the flash.
• When a Speedlite EX series flash is mounted, you cannot set the built-in
flash.
• Some functions on Speedlite 270EX, 430EX II, and 580EX II cannot be
used with this camera.
• When using Canon brand flashes other than Speedlite EX series
models, the flash may not fire correctly, or may not fire at all. Flashes
with a manual firing function can be used in manual mode, however redeye correction is not available.
• Using a non-Canon brand flash (particularly a high-voltage flash) or flash
accessories may inhibit normal operation or damage the camera.
Y
P
O
Attach the case for the hot shoe
cap to the strap.
● Remove the strap from the camera.
● Pass the strap through the back of the
C
case.
● Attach the strap to the camera (p. 13).
Remove the hot shoe cap.
● Push ( ) and lift ( ) the cap to remove it.
● To avoid losing the cap when you remove
it, place it in the case you attached to the
strap.
Attach the flash to the hot shoe.
168
Using an Externally Mounted Flash (Sold Separately)
Turn the flash on, then turn the
camera on.
X A red h appears on the screen (or the
viewfinder).
X When the flash is charged, its pilot lamp will
light.
Display the flash settings screen.
● Press the n button to choose [Flash
Control] from the 4 tab, then press the
m button.
X The options set on the flash will appear.
Y
P
O
Make the setting.
● Press the op buttons or turn the  dial
C
to choose an item, then press the qr
buttons to adjust the setting.
● The available settings differ depending on
the flash (p. 170).
● In modes other than G, M, B, and D,
flash settings cannot be changed since the
flash adjusts and fires automatically.
If you hold down the h button for more than one second, you can also
display the settings screen.
Attaching the Hot Shoe Cap
● Attach the hot shoe cap when you are not
using an externally mounted flash.
169
Using an Externally Mounted Flash (Sold Separately)
Configuring the Externally Mounted Flash
(Sold Separately)
Speedlite 270EX, 430EX II, and 580EX II
• The maximum flash synchro shutter speed is 1/250 second.
• The flash output will automatically adjust when [Flash Mode] is set to
[Auto]. Flash exposure compensation and safety FE can also be set.
However, when setting flash exposure compensation on the camera, make
sure to set the flash exposure compensation amount on the flash to [+0]
beforehand.
• The flash output can be adjusted on the camera or the flash* if [Flash
Mode] is set to [Manual].
* With Speedlite 270EX, settings cannot be made on the flash.
• In D mode, you can set the flash output on the camera even if the flash
unit is set to E-TTL flash exposure compensation. [E-TTL] will display on
the flash, but the flash will fire at the flash output set on the camera. The
flash compensation amount set on the flash will also change.
• Settings available on the camera are as follows.
Item
C
Y
P
O
Options
G
Shooting mode
M B D
Flash Mode
Auto/Manual
{
{
{
Flash Exp.Comp
-3 to +3
{
{
{
*1
–
Flash Output
1/128*2 to 1/1 (in 1/3 steps)
{
{
{
{
Shutter Sync.
1st-curtain/2nd-curtain/Hi-Speed
{
{
{
{
Slow Synchro
On/Off
{
{
Wireless Func.*4
On/Off
{
*3
{
{
*3
{
Red-Eye Corr.
On/Off
{
{
{
{
Red-Eye Lamp
On/Off
{
{
{
{
Safety FE
On/Off
{
{
{
Clear Flash Settings*6
Resets settings to their default values.
{
{
{
*5
{
170
Using an Externally Mounted Flash (Sold Separately)
*1
*2
*3
*4
*5
*6
Fixed to [Manual].
1/64 for Speedlite 270EX and 430EX II.
Fixed to [On].
Settings aside from On/Off are set on the flash. Not available with Speedlite 430EX II.
When set to [On], [Shutter Sync.] cannot be set to [2nd-curtain]. Even if you set [Shutter Sync.] to
[2nd-curtain] on the camera, it will change to [1st-curtain].
Fixed to [Off].
[Slow Synchro], [Safety FE], [Red-Eye Corr.] and [Red-Eye Lamp] can also be returned to their
default values using [Reset All] in the camera’s 3 menu (p. 53).
• The settings from the flash are applied to the flash mode, flash exposure compensation,
flash output, shutter synchro, and wireless function when you turn on the camera.
• The following functions can also be used:
- Auto Exposure (Set the camera to E-TTL mode)
- FE Lock (When [Flash Mode] is set to [Auto])
- Auto Zoom (Not available with the 270EX))
Y
P
O
• For continuous shooting, the flash can be used in quick flash mode (pilot
lamp lit green). In this case, flash output may be less than with full flash
(pilot lamp lit red) (580EX II only).
• If the external flash has been set to stroboscopic flash, the flash’s set-up
menu cannot be chosen (580EXII only).
C
• Speedlite 380EX, 420EX, 430EX, 550EX, and 580EX can be used in the
same way.
Using Speedlite 430EX II and 580EX II
Using the separately sold Speedlite Bracket SB-E2
prevents unnatural shadows from appearing on the
sides of objects when shooting from a vertical
position. However, depending on the angle, the
bracket may interfere with opening the LCD
monitor. Please use the camera with the LCD
monitor closed and the screen facing outward.
Other Canon Flashes
Canon flashes other than the Speedlite EX series will fire at their full strength.
For the optimal aperture values and ISO speeds for the distance to the
subject, refer to the guide number listed in the flash’s user guide.
171
Using an Eye-Fi Card
Before using an Eye-Fi card, be sure to check whether Eye-Fi card use is
authorized in the country or territory of use (p. 16).
When you put a prepared Eye-Fi card into the camera, you can automatically
transfer your images wirelessly to a computer, or upload them to a web
service.
Image transfer is a function of the Eye-Fi card. For details on how to setup
and use the card, and concerning problems transferring images, please refer
to the Eye-Fi card user guide, or contact the manufacturer.
Please keep the following things in mind when using an Eye-Fi card.
• Even if you set [Eye-Fi trans.] to [Disable] (p. 173), the Eye-Fi card may
transmit radio waves. Be sure to remove the Eye-Fi card from the camera
before entering areas that prevent unauthorized transmission of radio waves,
such as hospitals and airplanes.
• If you have trouble transferring images, check the card or computer settings.
For details, refer to the user guide supplied with the card.
• Depending on the connection status of the wireless network, it may take time
to transfer images, or image transfer may be interrupted.
• Due to its transfer function, the Eye-Fi card may become hot.
• Battery consumption will be quicker than in normal use.
• Camera operations will be slower than in normal use. This may be resolved
by setting [Eye-Fi trans.] to [Disable].
C
Y
P
O
If you put an Eye-Fi card into the camera, the connection status can be
checked in the shooting screen (Information Display) and playback screen
(Simple Information Display).
(Gray)
Not connected
(Flashing white)
Connecting
(White)
Transfer standby
(Animated)
Transferring
Interrupted
Error retrieving Eye-Fi card info (Turn the camera off and on
again. If this continues to appear, there may be a problem with
the card.)
will appear on transferred images.
The power saving function does not work while transferring images (p. 52).
172
Using an Eye-Fi Card
Checking Connection Information
You can check the Eye-Fi card’s access point SSID, or connection status.
Choose [Connection info].
● Press the n button, then choose
[Eye-Fi Settings] from the 3 tab, and
press the m button.
● Press the op buttons or turn the  dial
to choose [Connection info], then press the
m button.
X The Connection info screen will appear.
Y
P
O
Disabling Eye-Fi Transfer
You can set the card to disable Eye-Fi transfer.
Choose [Disable] in [Eye-Fi trans.].
C
● Press the n button to choose [Eye-Fi
Settings] from the 3 tab, then press the
m button.
● Press the op buttons or turn the  dial
to choose [Eye-Fi trans.], then press the
qr buttons to choose [Disable].
What if [Eye-Fi Settings] does not appear?
[Eye-Fi Settings] will only appear when an Eye-Fi card is inserted in the camera.
If the Eye-Fi card has a write-protect tab, you will not be able to check the
card's connection status, or set [Eye-Fi trans.] to [Disable] when the tab is
in the locked position.
173
Troubleshooting
If you think there is a problem with the camera, first check the following. If the
items below do not solve your problem, contact a Canon Customer Support
Help Desk as listed on the included customer support list.
Power
You pressed the power button, but nothing happened.
•
•
•
•
Confirm that the battery is the correct type, and is not depleted (p. 15).
Confirm that the battery is properly inserted (p. 17).
Confirm that the memory card/battery cover is securely closed (p. 17).
If the battery terminals are dirty, battery performance will decrease. Clean the
terminals with a cotton swab and re-insert the battery several times.
Battery is consumed quickly.
• Battery performance decreases at low temperatures. Warm the battery, for example,
by placing it in your pocket with the terminal cover on.
Lens will not retract.
Y
P
O
• Do not open the memory card/battery cover while the power is on. After closing the
memory card/battery cover, turn the power on then back off (p. 17).
TV output
Image is distorted or not showing on TV (p. 127).
Shooting
Cannot shoot.
C
• When in Playback mode (p. 22), press the shutter button halfway (p. 24).
The screen is off (p. 27).
Screen does not display properly in dark places (p. 47).
Screen does not display properly while shooting.
Please note, the following will not be recorded in still images, but will be recorded in movies.
• When the camera is subjected to powerful light sources, the display may darken.
• When shooting under fluorescent or LED lighting, the screen may flicker.
• When shooting bright light sources, a bar of light (purplish red) may appear on the
screen.
A flashing h appears on the screen and the shot cannot be taken even
though the shutter button was pressed fully (p. 27).
appears when the shutter button is pressed halfway (p. 27).
•
•
•
•
Set the [IS mode] to [Continuous] (p. 161).
Raise the flash and set it to h (p. 72).
Increase the ISO speed (p. 76).
Attach the camera to a tripod. Additionally, you should set the [IS Mode] to [Off] when
shooting with a tripod (p. 161).
174
Troubleshooting
Image is blurred.
•
•
•
•
•
Press the shutter button halfway to focus on the subject, then press fully to shoot (p. 24).
Shoot the subject within the focusing distance (p. 189).
Set the [AF-assist Beam] to [On] (p. 158).
Confirm that functions which you do not intend to use (macro, etc.) are not set.
Shoot using the focus lock or AF lock (pp. 82, 87).
Even when you press the shutter button halfway, the AF frame does not
appear, and the camera does not focus.
• If you center on the light and dark contrasting area of the subject and push the shutter
button halfway, or repeatedly push the shutter button halfway, the AF frame will appear
and the camera will focus.
Subject is too dark.
•
•
•
•
Raise the flash and set it to h (p. 72).
Correct the brightness with exposure compensation (p. 73).
Adjust the image with i-Contrast (pp. 98, 141).
Use AE Lock, or spot metering to shoot (pp. 92, 93).
Y
P
O
Subject is too bright (overexposed).
•
•
•
•
Lower the flash and set it to ! (p. 26).
Correct the brightness with exposure compensation (p. 73).
Use AE Lock, or spot metering to shoot (pp. 92, 93).
Reduce the light illuminating the subject.
C
Image is dark even though the flash fired (p. 27).
• Shoot within an appropriate distance for flash photography (p. 72).
• Correct the flash exposure compensation amount or flash output (p. 100).
• Increase the ISO speed (p. 76).
Image taken using the flash is too bright (overexposed).
• Shoot within an appropriate distance for flash photography (p. 72).
• Lower the flash and set it to ! (p. 26).
• Correct the flash exposure compensation amount or flash output (p. 100).
White dots appear on the image when shooting with the flash.
• Light from the flash has reflected off dust particles or other objects in the air.
Image appears rough or grainy.
• Shoot with the ISO speed on a lower setting (p. 76).
• Depending on the Shooting mode, when shooting in a high ISO speed the image may
appear rough or grainy (p. 62).
Eyes appear red (p. 98).
• Set the [Red-Eye Lamp] to [On] (p. 159). When shooting with the flash, the lamp (on
the front of the camera) lights (p. 44), and for approximately 1 second while the camera
is reducing red-eye, it is not possible to shoot. It is more effective if the subject is
looking directly at the lamp. Even better results can be obtained by increasing the
lighting in indoor settings or approaching closer to the subject.
175
Troubleshooting
Recording images to the memory card takes a long time, or continuous
shooting slows down.
• Perform a low-level format of the memory card in the camera (p. 54).
Cannot make settings for shooting functions or ø menu.
• The items in which settings can be made differ depending on the shooting mode. Refer
to “Functions Available in Each Shooting Mode” and “Shooting Menu” (pp. 182 – 185).
Shooting movies
Correct shooting time does not display, or stops.
• Format the memory card in the camera, or use a memory card capable of recording at
high speeds. Even when the shooting time does not display properly, the recorded
video will be the length that it was actually shot (pp. 23, 31).
The full buffer warning (p. 179) appeared on the screen and shooting ended
automatically.
Y
P
O
The camera’s internal memory was insufficient. Try one of the following:
• Perform a low-level format of the memory card in the camera (p. 54).
• Change the image quality setting (p. 111).
• Use a memory card capable of recording at high speeds (p. 111).
Playback
Cannot play back images or movies.
C
• If the file name or folder structure is changed on a computer, you may not be able to
play back images or movies. Refer to the Software Guide for information regarding
folder structure or file names.
Playback stops, or audio cuts out.
• Use a memory card that has had a low-level format performed on it with this camera
(p. 54).
• If you copy a movie to a memory card that reads slowly, playback may interrupt
momentarily.
• Depending on its capabilities, when playing movies on a computer, frames may drop
or the audio may cut out.
Computer
Cannot transfer images to a computer.
It may be possible to solve the problem when the camera is connected to a computer via cable
by reducing the transfer speed.
• Press the 1 button to enter Playback mode. Then press and hold the n button
and press the o and m buttons together. In the screen that appears, press the qr
buttons to choose [B] and press the m button.
Eye-Fi Card
Cannot transfer images (p. 172).
176
List of Messages That Appear on the Screen
If error messages appear on the screen, try one of the following solutions.
No memory card
• The memory card is not installed in the correct direction. Install the memory card in the
correct direction (p. 17).
Memory card locked
• The SD memory card, SDHC memory card or SDXC memory card’s, or the Eye-Fi
card's write protect tab is set to “LOCK”. Unlock the write protect tab (pp. 16, 17).
Cannot record!
• You attempted to shoot an image without a memory card. Install the memory card in
the correct direction to shoot (p. 17).
Memory card error (p. 54)
• If the same message appears even when a formatted memory card is installed in the
correct direction, contact a Canon Customer Support Help Desk (p. 17).
Insufficient space on card
Y
P
O
• There is not enough free space on the memory card to shoot (pp. 25, 30, 57, 71, 107)
or edit images (pp. 138 – 142). Erase the images (pp. 29, 132) to open space for new
images, or insert an empty memory card (p. 17).
Change the battery pack. (p. 15)
No Image.
• There are no images recorded on the memory card that can be displayed.
C
Protected! (p. 129)
Unidentified Image/Incompatible JPEG/Image too large./Cannot play back AVI/
RAW
• Unsupported images, or images with corrupted data cannot be displayed.
• Images manipulated on a computer, that have had their file name changed, or have
been taken with a different camera may not display.
Cannot magnify!/Cannot play back this content in Smart Shuffle/Cannot
rotate/Cannot modify image/Cannot register this image!/Cannot modify/
Cannot assign to category/Unselectable image.
• Incompatible images cannot be magnified (p. 125), played back in Smart Shuffle
(p. 125), tagged as favorites (p. 134), rotated (p. 137), edited (pp. 138 – 142),
registered to the start-up screen (p. 153), categorized (p. 135), or added to a print list
(pp. 146, 147).
• Images manipulated on a computer, that have had their file name changed, or have
been taken with a different camera may not be magnified, played back in Smart
Shuffle, tagged as favorites, rotated, edited, registered to the start-up screen,
categorized, or added to a print list.
• Movies cannot be magnified (p. 125), played back in Smart Shuffle (p. 125), edited
(pp. 138 – 142), added to a print list (pp. 146, 147), or registered to the start-up screen
(p. 153).
177
List of Messages That Appear on the Screen
Invalid selection range
• When choosing the selection range (pp. 130, 133, 136, 147), you tried to choose a
starting image that was after the last image or you tried to choose an ending image
that was before the starting image.
Exceeded selection limit
• You chose more than 998 images in print settings. Choose less than 998 images
(p. 148).
• Print settings could not be saved correctly. Reduce the number of selected images and
try again (p. 148).
• You chose 501 or more images in Protect (p. 129), Erase (p. 132), Favorites (p. 134),
My Category (p. 135) or Print Settings (DPOF) (p. 147).
Communication error
• Images could not be transferred to the computer or printed due to the large amount of
images (approx. 1000) stored on the memory card. Use a commercially available USB
card reader to transfer the images. Insert the memory card into the printer’s card slot
to print.
Naming error!
Y
P
O
• The folder or image could not be created because there is an image with the same file
name as the folder or image that the camera is attempting to create, or the highest
possible file number has already been reached. In the 3 menu, change [File
Numbering] to [Auto Reset] (p. 154) or format the memory card (p. 23).
Lens Error
C
• This error can occur if you hold the lens while it is in motion or when using it in a
location with excessive dust or sand in the air.
• If this error message continues to appear, contact a Canon Customer Support Help
Desk as there may be a problem with the lens.
A camera error was detected (Error number)
• If an error code appears directly after taking a picture, the shot may not have been
recorded. Check the image in Playback mode.
• If this error code reappears, note the Error number (Exx) and contact a Canon
Customer Support Help Desk as there may be a problem with the camera.
178
Information Displayed on the Screen
Shooting (Information Display)
The same information will display on the viewfinder.
Battery Charge Indicator
(p. 15)
Camera Orientation*
White Balance (p. 77)
My Colors (p. 79)
AEB Shooting (p. 94) /
Focus Bracketing (p. 90)
Drive Mode (p. 78)
Eye-Fi Connection
Status (p. 172)
Metering Method (p. 92)
Histogram (p. 47)
Compression (p. 74),
Recording Pixels (p. 74)
Still images: Recordable
Shots (p. 75)
Self-Timer
(pp. 61, 80, 81)
Movies: Recording Pixels
(p. 111)
Movies: Remaining Time
(p. 111)
Y
P
O
Digital Zoom Magnification
(p. 58) / Digital Teleconverter (p. 59)
Focusing Range (pp. 73,
89) / AF Lock (p. 87)
Shooting Mode (p. 182),
Scene Icon (p. 180)
Flash Mode
(pp. 26, 72, 99)
Red-Eye Correction
(p. 142)
Flash Exposure
Compensation / Flash
Output (p. 100)
Spot AE Point Frame
(p. 92)
Date Stamp (p. 60)
ISO Speed (p. 76)
Grid Lines (p. 160)
AE Lock (p. 93), FE Lock
(p. 93)
3:2 Guide (p. 160)
Shutter Speed
(pp. 95, 97)
C
AF Frame (p. 84)
Estimated Display Area
before Pressing the
Button (p. 91)
Aperture Value
(pp. 96, 97)
Exposure Compensation
Amount (p. 73)
Image Area: Movies
(p. 26) / Image Area: Still
Images (p. 111)
i-Contrast (p. 98)
Camera shake warning
(p. 27)
Exposure Shift Bar
(p. 113)
Zoom Bar (p. 25)
Blink Detection (p. 101)
Exposure Level (p. 97)
MF Indicator (p. 89)
Buffer Warning
Image Stabilizer (p. 161)
Time Zone (p. 156)
Movie Audio (p. 114)
179
Information Displayed on the Screen
*
: Standard,
: Held vertically
When shooting, the camera detects if it is held vertically or horizontally, and adjusts
settings accordingly for the best shot. It also detects orientation during playback, so you
can hold the camera in either orientation and it will automatically rotate images for
correct viewing.
This function may not operate correctly when the camera is pointed straight up or
down.
Scene Icons
In A mode, the camera displays an icon for the scene it has determined
and then automatically focuses and selects the optimum settings for subject
brightness and color.
Subject
People
With
Strong
Facial
Shadows
When
Moving
Back
ground
Bright
C
Backlit
Including
Blue Skies
Backlit
Sunsets
NonHuman
Subjects/
Landscap
es
Y
P
O
Close
Subjects
Icon
Backgrou
nd Color
Gray
—
Light Blue
—
—
—
Orange
Spotlights
Dark
When
Using
Tripod
Dark Blue
*
—
*
—
* Appears when the scene is dark and the camera is attached to a tripod.
180
Information Displayed on the Screen
Playback (Detailed Information Display)
Print List (pp. 146, 147)
My Category (p. 135)
Shooting mode (p. 182)
ISO Speed (p. 76),
Playback Speed
(Movies) (p. 109)
Exposure Compensation
(p. 73), Exposure Shift
Amount (p. 113)
White Balance (p. 77)
Histogram (p. 47)
Image Editing
(pp. 138 – 142)
Compression (Image
Quality) (p. 74) /
Recording Pixels (p. 74),
MOV (Movies)
Y
P
O
Eye-Fi Transfer
Complete (p. 172)
Battery Charge Indicator
(p. 15)
Metering Method (p. 92)
Folder Number – File
Number (p. 154)
Displayed image number
/ Total number of images
Shutter Speed
(pp. 95, 97)
Aperture Value (pp. 96,
97), Image Quality
(Movies) (p. 111)
i-Contrast (pp. 98, 141)
Flash (pp. 72, 99), Flash
Exposure Compensation
(p. 100)
C
Focusing Range
(pp. 73, 89)
File Size (pp. 75, 111)
Still Images: Recording
Pixels (p. 74)
Movies: Movie Length
(p. 111)
Protect (p. 129)
Favorites (p. 134)
My Colors (pp. 79, 140)
Red-Eye Correction
(pp. 98, 142)
Shooting Date and Time
(p. 20)
181
Functions Available in Each Shooting Mode
Shooting modes
D BM G A
Function
h
…
!
Flash (pp. 26, 72, 99)*1
Zoom Framing Assist (p. 91)
Change AF Frame Position and Size (p. 85)
Face Select (p. 88)
Exposure Compensation (p. 73)
AE Lock (p. 93)/FE Lock (p. 93)/Program Shift (p. 93)
AE Lock/Exposure Shift (p. 113)
e
Focusing Range (pp. 73, 89)
AF Lock (when registered to the
Self-Timer (pp. 61, 80, 81)
White Balance (p. 77)
My Colors (p. 79)
Bracketing (pp. 90, 94)
ÎÒ$
C
—
{
{
—
{
{
{
{
{
—
{
—
—
{
{
{
{
{
{
{
{
—
{
{
{
{
{
*6
{
{
{
{
—
{
{
{
*6
{
{
{
{
{
{
{
{
*6
{
{
{
{
{
{
{
{
*6
{
{
{
{
{
{
{
{
*3
—
{
—
{
—
—
—
—
{
—
—
{
—
{
{
*2
*2
*2
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
*2
*2
{
{
{
{
—
2
*
*2
*2
*2
*2
*2
2
*
*2
*2
*2
*2
*2
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
—
{
—
—
*2
*2
—
{
{
{
—
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
—
{
—
{
{
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
*2
Y
P
O
button) (p. 162)
ISO Speed (p. 76)
—
{
—
—
{
{
{
—
—
*2
{
—
FUNC. Menu
Drive Mode (p. 78)
W
Flash Exposure Compensation
(p. 100)
Flash Output Settings (p. 100)
-2 to +2
h
*
Metering Method (p. 92)
Recording Pixels (Still Images)/Compression Ratio (p. 74)
Image Quality (Movies) (p. 111)
*1 Fixed to ! when the flash is lowered, otherwise selectable when the flash is raised. *2 The available settings depend
on the registered shooting modes. *3 Not selectable but switches to … depending on the circumstances. *4 Not selectable
but switches to … when the flash fires. *5 Not available while shooting movies. *6 Only available while shooting movies.
*7 The number of shots cannot be specified, and the time delay cannot be set to 0 seconds. *8 White balance data not
recordable.
182
Functions Available in Each Shooting Mode
I J
{ { — {
{ { — {
— *4 — —
— — { —
{ { { {
— — — —
{ { — {
{ { { {
— — — —
{
{
—
—
{
—
{
{
—
{
{
—
—
{
—
{
{
—
{
—
—
—
{
—
{
{
—
{
{
—
—
{
—
{
{
—
{
{
—
—
{
—
{
—
—
*6 *6 *6 *6 *6 *6
— — — — — —
{ { { { { {
{ { — — — —
{ { — — — —
{ { { { { {
— — — — — —
{ { { { { {
{ { — — — —
*6
—
{
{
—
{
—
{
{
*6 *6
— —
{ {
{ {
{ {
{ {
— —
{ {
{ {
K
TY
{
{
{
{
— —
— —
{
{
— —
{ —
— {
— —
— *6
{ —
{
{
{
{
{
{
{
{
— —
{
{
{
{
—
—
{
—
—
{
—
w
{
{
—
—
{
—
{
{
—
O
{
{
—
—
{
—
{
{
—
P
{
{
—
—
{
—
{
{
—
*6 *6 *6 *6
— — — —
{ { { {
{ { { {
{ { { {
{ { { {
— — — —
{ { { {
*7 { { {
t xv E
— — —
— { —
— { —
{ — —
{ — {
— — —
— — {
{ { —
— — —
{
*6
*6
— { {
{ { {
— — {
— { {
{ { {
— — —
{ { {
{ *7
*7
Y
P
O
*7
*7
{ { { { { {
— — — — — —
{ { { { { {
{
{
{
FUNC. Menu
{ {
{
{ { { { { {
— — — — — — — — —
{ {
{
{ { { { { {
— — — — — —
—
— —
—
— — — — — —
{ { { { {
— — — — —
— — — — —
{ { { { {
{ { — — —
{ { { — —
{
—
—
{
—
—
{
—
—
{
{
{
{ {
— —
— —
{ {
{ {
{ {
{
—
—
{
{
{
{ { { { { {
— — — — — —
— — — — — —
{ { { { { {
{ { { { { {
{ { { { { *10
— — — — — —
—
— —
—
— — — — — —
— — — — — — — — —
{ { { { { { { { {
— — — — — — — — —
{ { { { { { *11 { {
{ { { { { { { { {
—
{
—
{
{
— — — — — —
{ { { { { {
— — — — — —
{ { { { { {
{ { { { { {
C
E
—
—
—
—
>z
*5
—
—
—
—
—
—
{
{
{
{
—
{
—
—
—
—
{
—
{
—
—
—
{
{
{
{
{
—
{
*7
*7
{
{
*8
{
*9
{
{
—
{
{
—
{
{
{
—
—
{
—
—
{
—
—
{
—
—
—
—
—
{
—
—
—
—
—
{
—
—
—
—
—
—
—
—
—
—
{
—
— —
{ {
— —
{ {
{ *13
—
{
—
{
{
*12
{
*9 h not available. *10
*11
will appear as the recording pixel setting, and the image will be fixed at 1600 x
1200 pixels. It will be possible to select a compression ratio (image quality) setting.
*12 Recording pixel setting
not selectable. *13 Recording pixel setting
not selectable.
{ Selectable, or set automatically. – Not selectable.
183
Menus
4 Shooting Menu
Shooting Modes
D BM G A
Function
FlexiZone
AF Frame (p. 84)
Center
Face Detect
Standard
Digital Zoom (p. 58)
Off
Digital Tele-converter (1.7x/2.1x)
AF-Point Zoom (p. 86)
On/Off
Servo AF (p. 86)
On/Off
Continuous AF (p. 78)
On/Off
AF-assist Beam (p. 158) On/Off
MF-Point Zoom (p. 86) On/Off
Safety MF (p. 89)
On/Off
Auto
Flash Mode
Manual
Flash Exp.Comp -2 to +2
Minimum/Medium/
Flash Output
Flash Control
Maximum
(pp. 98, 100, 159)
Shutter Sync. 1st-curtain/2nd-curtain
Red-Eye Corr. On/Off
Red-Eye Lamp On/Off
Safety FE
On/Off
i-Contrast (p. 98)
Auto/Off
Spot AE Point (p. 92)
Center/AF Point
Safety Shift (p. 96)
On/Off
Mic Level
Auto/Manual
Movie Audio (p. 114)
Level
Wind Filter
On/Off
Review (p. 159)
Off/2 – 10 sec./Hold
Off
Review Info (p. 160)
Detailed/Focus Check
Blink Detection (p. 101) On/Off
Shooting Info
Grid Lines
Custom Display (p. 160)
3:2 Guide
Histogram
Reverse Disp. (p. 19)
On/Off
Off/Continuous
IS Mode (p. 161)
Shoot Only/Panning
Display Area (p. 91) Small/Medium/Large
Date Stamp (p. 60)
Off/Date/Date & Time
Set Shortcut button (p. 162)
Save Settings (p. 102)
C
184
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
{
—
{
{
{
{
{
{
{
{
{
{
—
{
—
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
—
{
{
—
—
{
—
—
*1
*1
{
{
{
—
—
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
{
{
{
—
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
—
{
{
Y
P
O
*1 The available settings depend on the registered shooting modes.
*2 9 points when a face is not detected.
*3 [On] when movement of people is detected.
—
—
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
{
{
*2
{
{
{
{
*3
*4
*4
*5
—
—
{
{
{
{
{
{
{
{
{
{
*6
{
*7
—
{
{
{
—
Menus
I J
— — — — — — — — —
{ { { — — — { { {
{ { — { { { *2 { {
{ { { { { { — { {
{ { { { { { { { {
{ { { { { { — { {
{ { — { { { { { {
{ { *4 — — — { { {
{ { *4 *4 *4 *4 — { {
{ { — *4 { { { { {
{ { — — — — { { {
{ { — — — — { { {
{ { — { { { { { {
— — — — — — — — —
— — — — — — — — —
K
TY
— —
{
{
{ —
— —
{
{
— —
{ —
{ —
{
{
{
{
{ —
{
{
{
{
— —
— —
—
—
—
—
{
—
—
—
{
{
—
{
{
—
—
w
—
{
{
{
{
{
{
{
{
{
{
{
{
—
—
O
—
{
{
{
{
{
{
{
{
{
{
{
{
—
—
P
—
{
{
{
{
{
{
{
{
{
{
{
{
—
—
t xv E
— — —
{
{
{
— — {
—
{
{
{
{
{
{ — —
— — —
— — —
— {
*4
— {
{
— — —
— — {
— { —
— — —
— — —
Y
P
O
E
—
—
—
—
{
—
—
—
*4
>z
—
{
{
—
{
—
—
—
*4
{
—
{
—
—
—
{
—
{
—
—
—
— — — — — — — — —
—
— — — — — —
—
—
—
—
— — —
{ { —
{ { —
*4 *4 —
— — —
— — —
— — —
{ { {
{ { {
{ { {
{ { {
{ { {
{ { {
{ { —
{ { {
{ { {
{ { {
—
—
{
—
—
{
— — — *5 — —
— — — — — —
— — — — — —
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
—
—
—
{
{
{
{
{
{
{
{
{
{
— — — — — —
— — { { { —
{ { { { { —
*4 *4 *4 *4 *4 —
— — — — — —
— — — — — —
— — — — — —
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
— — { { { —
{ { { { { {
{ { { { { {
{ { { { { {
—
—
—
—
—
—
—
{
{
{
—
—
—
—
{
{
—
—
—
—
—
—
—
—
—
—
—
—
—
—
{
{
—
—
—
—
—
—
—
{
{
{
—
—
—
—
{
{
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
— — — — — —
{ { { { { {
{ { { { { {
*4
*4
*6
C
*4
*6
*4
*6
*4
*6
*4
*6
{ { { { { { { { {
{ { { { { { { { {
{ { { { { { { { {
{ { { { { { { { {
{ { { { { { — { {
{ { { { { { { { {
— — — — — — — — —
*4
{
{
{
{
{
{
—
*6
*6
*6
*6
*6
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
{ { { { { {
— — — — — —
*4
—
—
—
{
{
{
{
{
—
—
{
*6
*6
*6
—
{
{
—
—
{
—
{
{
—
{
—
{
—
{
{
—
{
—
{
—
{
{
—
{
—
{
—
*4 Fixed to [On].
*5 Fixed to [Auto].
*6 Selectable only, no settings available.
*7 Fixed to [Continuous].
{ Selectable, or set automatically. – Not selectable.
185
Menus
3 Set up Menu
Item
Mute
Volume
Sound Options
Hints & Tips
LCD Brightness
Start-up Image
Format
File Numbering
Create Folder
Lens Retract
Power Saving
Time Zone
Date/Time
Distance Units
Video System
Eye-Fi Settings
Language
Reset All
* Default setting
Content
On/Off*
Set all operation sounds (5 levels).
Set the sounds for each camera operation.
On*/Off
Set within a range of ±2.
Add an image as a start-up image.
Formats memory card, erasing all data
Continuous*/Auto Reset
Monthly*/Daily
1 min.*/0 sec.
Auto Power Down: On*/Off
Display Off: 10, 20 or 30 sec./1*, 2 or 3 min.
Home*/World
Date and time settings
m/cm* / ft/in
NTSC/PAL
Eye-Fi connection settings (only appears when
Eye-Fi card is inserted)
C
Y
P
O
Choose display language.
Returns camera to default settings.
Ref. Page
p. 50
p. 50
p. 152
p. 152
p. 51
p. 153
pp. 23, 54
p. 154
p. 155
p. 155
pp. 52,
155, 156
p. 156
p. 21
p. 157
p. 127
p. 172
p. 22
p. 53
My Menu Menu
Item
My Menu settings
186
Content
Sets the items registered to My Menu.
Ref. Page
p. 163
Menus
1 Playback Menu
Item
Smart Shuffle
Slideshow
Erase
Protect
Rotate
Favorites
My Category
i-Contrast
Red-Eye Correction
Trimming
Resize
My Colors
Scroll Display
Resume
Transition
* Default setting
Print
Select Images & Qty.
Select Range
Select All Images
Clear All Selections
Print Settings
Ref. Page
p. 125
p. 123
p. 132
Content
Displays printing screen (When connected to a
printer).
Ref. Page
—
C
2 Print Menu
Item
Content
Starts Smart Shuffle.
Plays back images automatically.
Erases images (Select, Select Range, All
Images).
Protects images (Select, Select Range, All
Images).
Rotates images.
Tags or untags images as favorites.
Categorizes images (Select, Select Range)
Corrects dark portions and contrast in still
images.
Corrects red eyes in still images.
Trims portions of still images.
Resizes and saves still images.
Adjusts colors in still images.
On*/Off
Last seen*/Last shot
Fade*/Scroll/Slide/Off
Y
P
O
Chooses individual images for printing.
Chooses starting and ending images for
printing.
Chooses all images for printing.
Cancels all settings for printing.
Sets the printing style.
p. 129
p. 137
p. 134
p. 135
p. 141
p. 142
p. 139
p. 138
p. 140
p. 120
p. 164
p. 126
p. 148
p. 149
p. 149
p. 149
p. 147
187
Handling Precautions
• This camera is a high-precision electronic device. Do not drop it or subject
it to strong impacts.
• Never place the camera close to magnets, motors or other devices that
generate strong electromagnetic fields. Exposure to strong magnetic fields
may cause malfunctions or corrupt image data.
• If water droplets or dirt become stuck on the camera or screen, wipe with
a dry soft cloth or eyeglass wiper. Do not rub or apply force.
• Never use cleaners containing organic solvents to wipe the camera or
screen.
• Use a commercially available blower brush to remove dust from the lens.
For stubborn dirt contact a Canon Customer Support Help Desk as listed
on the customer support leaflet supplied with your camera.
• When you move the camera rapidly from cold to hot temperatures,
condensation may form on the internal or external surfaces of the camera.
To avoid condensation, put the camera in an airtight, resealable plastic bag
and let it adjust to temperature changes slowly before removing it from the
bag.
• If condensation has formed on the camera, stop using it immediately, as
continued use may damage the camera. Remove the battery and memory
card, and wait until the moisture has completely evaporated before
resuming use.
C
188
Y
P
O
Specifications
Image Sensor
Camera Effective Pixels ..... Approx. 14.1 million pixels
Lens
Focal Length....................... 35x zoom: 4.3 (W) – 150.5 (T) mm (35mm film equivalent:
24 (W) – 840 (T) mm)
Focusing Range ................. 0 cm (0 in.) – infinity (W), 1.4 m (4.6 ft.) – infinity (T)
• Macro: 0 – 50 cm (W) (0 in. – 1.6 ft. (W))
Image Stabilizer System..... Lens-shift type
Imaging Processor................... DIGIC4
Electronic Viewfinder ............... Effective pixels: approx. 202,000 dots (67,000 x 3)
• Brightness adjustment (5 levels), dioptric adjustment
LCD Monitor
Type ................................... TFT color (wide viewing angle type)
Size .................................... 2.7 type
Effective Pixels ................... Approx. 230,000 dots
Aspect Ratio ....................... 4:3
Features ............................. Brightness adjustment (5 levels), Quick-bright LCD
Variangle type (opening angle approx. 175°, rotational angle
approx. 270°)
Focus
Control System................... Autofocus: Single (Continuous in Auto mode), Continuous AF,
Servo AF (Servo AE)
Manual Focus
AF Frame ........................... Face Detect, Center, FlexiZone
Metering System...................... Evaluative, Center-weighted average, Spot
Exposure Compensation
(Still Images)/Exposure Shift
(Movies)................................... ±2 stops in 1/3-stop increments
ISO Speed
(Standard Output Sensitivity,
Recommended Exposure
Index)....................................... Auto, ISO 80/100/200/400/800/1600
White Balance ......................... Auto, Day Light, Cloudy, Tungsten, Fluorescent, Fluorescent H,
Flash, Custom
Shutter Speeds........................ 1 – 1/3200 sec.
15 – 1/3200 sec. (Total shutter speed range)
Aperture
Type ................................... Iris
f/number ............................. f/2.7 – f/8.0 (W), f/5.8 – f/8.0 (T)
Flash
Modes................................. Auto, On, Slow Synchro, Off
Hot Shoe ............................ Available
Range................................. 50 cm – 5.8 m (W), 1.4 – 2.8 m (T)
(1.6 – 19 ft. (W), 4.6 – 9.2 ft. (T))
C
Y
P
O
189
Specifications
Shooting Mode ........................ C2, C1, M, Av, Tv, P, Auto, Portrait, Landscape, Sports, SCN*1,
Movie*2*3
*1 Smart Shutter*4,Low Light, Super Vivid, Poster Effect, Color
Accent, Color Swap, Fish-eye Effect, Miniature Effect,
Beach, Foliage, Snow, Fireworks, Stitch Assist
*2 Smart Auto available
*3 Standard, Miniature Effect, Color Accent, Color Swap
*4 Smile, Wink Self-timer, Face Self-timer
Digital Zoom ............................ Still images/Movies: Approx. 4.0x (up to approx. 140x in
combination with the optical zoom) Safety Zoom, Digital teleconverter
Continuous Shooting
Mode .................................. Normal, AF, LV
Speed (Normal).................. Approx. 1.3 shots/sec. (In P mode)
Approx. 3.6 shots/sec. (In Low Light mode)
Number of Shots (Approximate)
(CIPA compliant) ..................... Approx. 400 shots (Viewfinder)
Approx. 370 shots (LCD Monitor)
Recording Media ..................... SD memory card, SDHC memory card, SDXC memory card
MultiMediaCard, MMCplus card, HC MMCplus card
File Format .............................. Design rule for Camera File system, DPOF (Version 1.1)
compliant
Data Type
Still Images......................... Exif 2.3 (JPEG)
Movies................................ MOV (Image data: H.264; Audio data: Linear PCM (stereo))
Recording Pixels
Still Images......................... Large: 4320 x 3240, Medium 1: 3072 x 2304, Medium 2: 1600 x
1200, Small: 640 x 480, Wide: 3744 x 2104
• Fixed to 1600 x 1200 when in Low Light
Movies................................ Smart Auto, Standard, Color Accent, Color Swap: 1280 x 720
(30 fps*), 640 x 480 (30 fps*), 320 x 240 (30 fps*)
Miniature Effect: 1280 x 720 (Shooting: 6 fps/3 fps/1.5 fps,
Playback: 30 fps*2), 640 x 480 (Shooting: 6 fps/3 fps/1.5 fps,
Playback: 30 fps*2)
* Actual frame rate is 29.97 fps.
Interface .................................. Hi-Speed USB
HDMI output
Analog audio output (stereo)
Analog video output (NTSC/PAL)
Direct Print Standard ............... PictBridge
Power Source.......................... Battery Pack NB-7L
AC Adapter Kit ACK-DC50
Dimensions.............................. 122.9 x 92.4 x 107.7 mm ( 4.84 x 3.64 x 4.24 in.)
• CIPA compliant
Weight (CIPA compliant) ......... Approx. 601 g (21.2 oz.) (Including the battery and memory
card)
Approx. 552 g (19.5 oz.) (camera body only)
C
190
Y
P
O
Specifications
Battery Pack NB-7L
Type.........................................
Voltage ....................................
Capacity...................................
Charging cycles .......................
Operating temperature ............
Dimensions..............................
Weight .....................................
Rechargeable lithium-ion battery
7.4 V DC
1050 mAh
Approx. 300 times
0 – 40 °C (32 – 104 °F)
32.5 x 46.4 x 17.7 mm (1.28 x 1.83 x 0.70 in.)
Approx. 47 g (1.66 oz.)
Battery Charger CB-2LZ/CB-2LZE
Rated input .............................. AC 100 - 240 V (50/60Hz)
14 VA (100 V) – 19.2 VA (240 V), 0.14 A (100 V) – 0.08 A (240 V)
Rated output ............................ DC 8.4 V, 0.7 A
Charge time ............................. Approx. 2 hr. 20 min.
Operating temperature ............ 0 – 40 °C (32 – 104 °F)
Dimensions.............................. 92.4 x 27.0 x 62.0 mm (3.64 x 1.06 x 2.44 in.)
Weight ..................................... Approx. 92 g (3.25 oz.) (CB-2LZ)
Approx. 85 g (3.00 oz.) (CB-2LZE) (excluding power cord)
Y
P
O
Lens Hood LH-DC60 (Sold Separately)
Largest Diameter x Length ...... 69.6 x 27.0 mm (2.74 x 1.06 in.)
Weight ..................................... Approx. 10 g (0.35 oz.)
C
• All data is based on tests by Canon.
• Camera specifications or appearance are subject to change without notice.
191
Index
A
AC Adapter Kit................................... 39, 166
Accessories ............................................... 39
AE Lock ............................................. 93, 113
AEB Mode ................................................. 94
AF J Focus
AF Frames.............................. 26, 84, 85
AF Lock ...................................... 87, 179
AFB Mode ......................................... 90, 179
AF-Point Zoom .......................................... 86
AUTO Mode (Shooting Mode)....... 25, 30, 44
Av (Shooting Mode)................................... 96
AV Cable ................................................. 127
B
C
C1/C2 (Shooting Mode)........................... 102
Camera
Default Settings .................................. 53
Camera Shake .................................. 27, 161
Clock Functions......................................... 55
Color Accent (Shooting Mode) ........ 103, 108
Color Swap (Shooting Mode) .......... 104, 108
Components Guide ................................... 44
Compression (Image Quality).................... 74
Continuous Shooting ................................. 78
D
Date and Time J Date/Time
Date/Time
Adding to Image ................................. 60
Changing ............................................ 21
192
E
Editing
i-Contrast .......................................... 141
My Colors ......................................... 140
Red-Eye Correction .......................... 142
Resizing (Making Images Smaller)... 138
Trimming........................................... 139
Erasing All Images .................................. 132
Erasing Images ................................. 29, 132
Error Messages ....................................... 177
Exposure
AE Lock ...................................... 93, 113
Correction ........................................... 73
FE Lock .............................................. 93
Shift .................................................. 113
Eye-Fi Card ....................................... 16, 172
Y
P
O
Battery
Battery Charger .................................. 14
Charge Indicator ................................. 15
Date/Time Battery............................... 21
Power Saving ............................. 52, 155
Recharge ............................................ 14
Battery Charger ..................................... 2, 39
Beach (Shooting Mode)............................. 64
Black and White Images............................ 79
Blink Detection ........................................ 101
Bracketing ................................................. 90
C
Date/Time Battery............................... 21
Setting ................................................ 20
World Clock ...................................... 156
Default Settings ......................................... 53
DIGITAL CAMERA Solution Disk ................ 2
Digital Tele-Converter ............................... 59
Digital Zoom .............................................. 58
Display Language...................................... 22
DPOF .............................................. 146, 147
Drive Mode ................................................ 78
Dynamic mode ........................................ 161
F
Face Detect (AF Frame Mode).................. 84
Face Select ............................................... 88
Face Self-Timer (Shooting Mode) ............. 68
Factory Settings J Default Settings
FE Lock ............................................. 93, 179
File Numbering ........................................ 154
Filtered Playback..................................... 121
Fireworks (Shooting Mode) ....................... 64
Fish-eye Effect (Shooting Mode)............... 69
Flash
Flash Exposure Compensation ........ 100
On....................................................... 72
Slow Synchro...................................... 99
Focus
Index
AF Frame...................................... 26, 84
AF Lock............................................... 87
AF-Point Zoom.................................... 86
Face Select......................................... 88
Servo AF............................................. 86
Focus Check............................................ 124
Focus Lock ................................................ 82
Focusing Range ........................................ 73
Manual Focus ..................................... 89
Foliage (Shooting Mode) ........................... 64
Format J Memory Cards, Formatting
Formatting (Memory Card) .................. 23, 54
FUNC. Menu
Menu................................................... 48
G
Y
P
O
Grid Lines ................................................ 179
H
Household Power .................................... 166
I
C
Manual Focus (Focus Mode).....................89
Manual White Balance...............................77
Memory Cards ...........................................16
Available Shots .............................18, 75
Formatting.....................................23, 54
Shooting Time............................. 31, 111
Memory Cards J Card
Menu
Basic Operations ................................49
List ....................................................184
Metering Method........................................92
Miniature Effect (Shooting Mode) ...... 70, 109
Movies
Editing...............................................117
Image Quality (Recording Pixels/
Frame Rate)......................................111
Modes ...............................................108
Shooting Time............................. 31, 111
Viewing (Playback) .....................32, 116
MultiMediaCard/MMCplus J Memory Cards
My Category ............................................135
My Colors ..................................................79
i-Contrast ........................................... 98, 179
Image Quality J Compression Ratio
Images
Display Time ..................................... 159
Editing J Editing
Erasing Images........................... 29, 132
Playback J Viewing
Protect .............................................. 129
Included Items J Accessories
Indicator..................................................... 45
Interface Cable .............................. 2, 35, 144
ISO Speed ......................................... 76, 179
L
Lamp.................................... 44, 47, 158, 159
Landscape (Shooting Mode) ..................... 62
LCD Monitor J Screen
Low Light (Shooting Mode)........................ 63
M
M (Shooting Mode) .................................... 97
Macro (Focus Mode) ................................. 73
Magnified Display .................................... 125
P
P (Shooting mode)..................................... 72
Personal Printing Guide...............................2
PictBridge ..........................................41, 144
Playback J Viewing
Playback With Transition Effects .............126
Portrait (Shooting Mode) ...........................62
Poster Effect (Shooting Mode) ..................65
Power JBattery and Charger Kit, AC Adapter
Kit
Power Saving ....................................52, 155
Printing ....................................................144
Program AE ...............................................72
Protect .....................................................129
R
Recording Pixels (Image Size) ..................74
Red-Eye Correction ...........................98, 142
Resizing (Making Images Smaller)..........138
Rotate ...................................................... 137
193
Index
S
SCN (Shooting Mode) ............................... 63
Screen
Display Language............................... 22
Information Display................... 179, 181
Menu J FUNC. Menu, Menu
Switching the Display ......................... 46
SD/SDHC/SDXC Memory Card J Memory
Cards
Self-Timer
10 Second Self-Timer......................... 61
Changing Delay and Number of
Shots .................................................. 81
Face Self-Timer (Shooting Mode) ...... 68
Two Second Self-Timer ...................... 80
Wink Self-Timer (Shooting Mode) ...... 67
Sepia Tones .............................................. 79
Servo AF ................................................... 86
Shooting
Number of Shots..................... 15, 18, 75
Shooting Date and Time J Date/Time
Shooting Info ............................ 160, 179
Shooting Time ............................ 31, 111
Shooting Using a TV ................................. 82
Slideshow ................................................ 123
Smart Shuffle........................................... 125
Smile (Shooting Mode).............................. 66
Snow (Shooting Mode).............................. 64
Software
DIGITAL CAMERA Solution Disk ......... 2
Installation .......................................... 34
Software Guide..................................... 2
Transferring Images to a Computer for
Viewing ............................................... 33
Sound Settings .......................................... 50
Sports (Shooting Mode) ............................ 62
Stereo AV Cable.................................. 2, 127
Stitch Assist (Shooting Mode) ................. 106
Super Vivid (Shooting Mode) .................... 65
C
V
Video J Movies
Viewing
Filtered Playback .............................. 121
Images on a TV ........................ 127, 128
Index Display .................................... 120
Magnified Display ............................. 125
Single Image Playback ....................... 28
Slideshow ......................................... 123
Smart Shuffle.................................... 125
Viewing Images on a TV ................. 127, 128
Y
P
O
T
Tag Images as Favorites......................... 134
Terminal .................... 35, 127, 128, 144, 166
Travel Abroad.............................. 15, 39, 156
Trimming ................................................. 139
194
Troubleshooting....................................... 174
Tv (Shooting Mode)................................... 95
W
White Balance ........................................... 77
Wide (Recording Pixels)............................ 75
Wink Self-Timer (Shooting Mode) ............. 67
World Clock ............................................. 156
Z
Zoom ............................................. 25, 30, 58
MEMO
C
Y
P
O
195
Disclaimer
• Reprinting, transmitting, or storing in a retrieval system any part of this
guide without the permission of Canon is prohibited.
• Canon reserves the right to change the contents of this guide at any
time without prior notice.
• Illustrations and screenshots in this guide may differ slightly from the
actual equipment.
• The above items notwithstanding, Canon accepts no liability for
damages due to mistaken operation of the products.
C
CDP-E102-010
Y
P
O
© CANON INC. 2010