for AMT Olympus jet engine
or Jet Cat P 200
Assembly
Manual
AVIATION Design
ZI le chenet, 91490 Milly La Foret, FRANCE
Tel : 33 1 64 98 93 93
Fax : 33 1 64 98 93 88
e-mail : aviation.design@wanadoo.fr
www.adjets.com
Version 1-07-2010
1
INTRODUCTION
The Mirage 2000 is a famous French delta fighter built by Dassault Aviation. It is used in a lot of
countries and it is one of the most agile fighters. The Mirage 2000 has a single jet engine.
You love very big models, you love fighter, you love agile and aerobatic jets, you love power :
The 1/5 Mirage 2000 is for you.
The Mirage 2000 model is really incredible in flight. It is a very big models, very aerobatic with
good roll rate and incredible high angle of attack possibility. Flight is very reallistic and
impressive with big turbine sound and afterburner lights.
The Mirage 2000 from AVIATION DESIGN is fully CAD designed. Most of the plug parts were
CNC machined.. It is a scale model, with all the panel lines and rivets engraved in the fuselage.
Plug was covered with aluminium sheet to have scale apparence.
It contains many scale details, (gears, hinges, cockpit...).
The Mirage 2000 is designed for the new high thrust jet engines and incorporates special inlets and
ducting.
Of course the Mirage 2000 is fully molded in composite, and pre assembled : model is painted in
mold, all bulkeads are glued, all control surfaces are hinged. No important gluing are required.
The Mirage 2000 has a removable nose cone and a large canopy for an easy access to radio.
The large fuselage hatch gives also an excelent access to the turbine, fuel sytem and tailpipe.
KIT FEATURES :
•
•
•
•
•
•
•
•
•
•
•
•
•
High quality, grey gel-coated epoxy-glass
fuselage. All the panel lines are engraved. The
fuselage is in 2 parts for an easier building.
Nose cone in fiber.
Exhaust nozzle in fiber.
Canopy frame in 2 parts in fiber.
Access hatch requiring no additional
framework.
2 Epoxy-glass inlets fitted and glued.
2 Wings molded in epoxy under vaccum with
carbon reinforcement, high quality plywood
spare, aluminium tube and gear support fitted.
Fully molded composite fin.
Scale fiber details.
ABS cockpit interior and scale accessories.
Clear formed canopy.
Aluminium joining tubes.
Instructions in English.
2
Parts required to complete the kit :
•
Cockpit detail kit incl. 1/5 ejector seat & scale instrument panel.
•
Scale retractable landing gear incl. 2
main retracts + 1 front steering retract +
air control system + 3 scale oleo legs.
All gears are CNC machined and
aluminium casting. Very strong and
reliable for grass operation.
•
Wheels set + brakes incl 2 main
wheels + 2 front wheels, aluminium hub
+ bearings + scale brakes + air control
system.
•
Gear doors set incl. air cylinders, air control system, gear door sequencer and door
hinges.
•
Kevlar fuel tanks (4.2 liters) + BVM
upper tank.
3
•
Details set incl. refueling probe, 2 guns and 8
scale hinges.
•
Stainless steel double walded tailpipe.
•
2 Magic missiles + wing tip launch rails.
•
•
2 Mica missiles + wing launch rails.
2 Mica missiles + fuselage launch rails.
•
•
•
1 Centerline fuel tank + launch rail.
2 large underwing fuel tanks + launch rails.
Variable section aluminium tail cone.
4
•
Afterburner ring lights.
•
•
Water decals french air Force.
Water decals UAE air Force.
•
Protection covers.
Jet Engine :
1 AMT Olympus engine
or 1 Jet Cat P180 – P200 jet engine
DISCLAIMER
AVIATION Design assumes no liability for the operation and use of these products.
The owner and operator of these products should have the necessary experience and exercise common
sense. Said owner and operator must have a valid Model Airplane license and insurance, as required.
5
FIBREGLASS PREPARATION
The inside of the fuselage should be sanded with fresh #80 grit paper for best glue adhesion where
bulkheads and other attachments are fixed.
GLUING TECHNIQUES
All the plywood formers should be fitted with cyano adhesive and then glued with epoxy and glass fiber
tape. All other parts should be glued with epoxy.
It is possible to let the fuselage in 2 parts for transportation.
You can also glue the 2 parts together.
If you want to dismantle it easily, you'll have to screw the 2 parts together with 6 x 4 mm diameter screws
+ blind nuts.
Don't forget to glue the - screws with threadlock before to fly ......
6
CONSTRUCTION
FRONT FUSELAGE
Front Gear Doors and guns :
Guns :
We recommend to fit funs first so the fuselage keep the exact section before to cut big gear doors :
Cut guns as engraved panel lines
Glue resin guns with CA inside the fuselage
Doors :
Cut just one side (left) of the main front gear door according to the engraved panel lines and photos.
Glue the 3 door hinges with cyano.
Finish to cut the front gear door.
Cut the central front door to the engraved panel lines and photos and put a flat door hinge for openning
7
Cut the 2 side doors 15 mm longer than the engraved panel line (for easier gear movement rotation)
Glue the 4 door hinges with cyano.
Secure all door hinges with
small parker screws
Air cylinder
Fit the small air cylinder on the front
door hinge
2Side doors will be closed by a
spring
8
Assembling the nose gear
Screw the landing gear on the plywood
Fit the leg in the gear
Screw the 2 wheels
Glue the lights
Front came :
Glue the 2 control horn in the wood this the came
screw in
9
Main gear doors :
Cut the outer main gear door according to engraved panel lines and photos
Cut just one side of the main gear doors according to the engraved panel lines and photos. Cut them only
close to the gear door hinge position.
Glue the 4 metal door hinges with cyano (take care of the position according to the plan and photos .
Finish to cut the main gear doors.
Secure all door hinges with small parker screws (due to aerodynamic loads)
Glue de plywood door reinforcement to the
gear door
Glue the gear door cylinder plywood support
to the fuselage
Screw the long air cylinder both ends to the
plywood supports
Check the gear door can open and closed
without trouble
Open the fuselage according to the photo to
have clearance for the main air cylinder
10
WINGS
Cut the inner main gear door according to engraved panel lines and photos
Screw the landing gear box on the plywood
Fit the leg in the gear
Screw the wheels
11
LANDING GEAR :
Assemble the wings to the fuselage .
Fit the oleo legs on the aluminum box.
Check that the 2 wheels are parallel. Drill a 2.5 mm hole through the leg and the aluminum T to fix the leg
to the box.
Screw the main air cylinder to the plywood cylinder support
Fit the mounting in the fuselage and connect the ball link to the leg.
Check that the legs perfectly retract and extend without hard point.
You may have to sent a little the wing ply reinforcement to have a perfect retraction. You can also adjust
the retraction angle
If retraction is OK, you can glue the mounting in the fuselage with CA.
Note : on the aluminium ball link, the steel ball can be removed from one side
Screw the ball to the legs definively
To assemble and disassemble the model on the field, you can just plug or unplug the ball to the link
12
Gear doors (wheels ):
Glue the 2 plywood doors
together.
Insert 2 flat hinges between the 2
plywood layers
Insert the hinges in the wing skin
Connect the door to the leg with a
M3 link + threated rod + M3 ball
link
Adjust the length so the door close
perfectly when the gear close
13
Wings servos
Servos MUST be very high quality servos, minimum 25 kg torque, with metal gear
Cut the servo location according to engraved panel lines and photos
Screw the servo in the servo cover
(we recommand to glue it with
silicon glue or strong glue)
Put in position the servo cover on the
wings
Drill 4 x 1 mm hole in the wings for
the screws
Cut a slot in the control surface for
the fiber control horn
Glue with fast epoxy the control horn
Connect M3 mm metal link with M3
threaded rod + M3 aluminium link
14
Glue a scale resine
control horn on each
side of the fiber control
horn
Screw the servo cover
with the 4 parker
screws
Connect the servo with
the control horn
Apply thread lock.
15
Wings tubes
Shorter wing tube fit in the front of the plane
Bigger section wing tube fit in the rear of the plane (to support gear loading).
Wings locking
system :
Assemble the plane
Drill a 4 mm diameter hole
through the fuselage root
and wing root from the gear
door
Fit a M4 blind nuts in the
wing and glue it with epoxy.
When you will assemble
your model on the airfield,
you will have to put the
model inverted , open the
main gear door and fit the
screws to secure the wings.
Don’t forget them
16
Assembly of the fin :
Fit the rudder on the fuselage
To secure the rudder, drill a 2.5 mm
hole and insert a 3 mm screw to lock
the fin.
Rudder :
It is possible to fit a rudder on the fin.
If you have choose to fit a rudder take
care to have no play in it. Otherwise,
you risk tail flutter.
Cut the rudder according to the
engraved line with a dremel saw (fine
saw).
Glue a 10 mm large balsa rib in the fin
and a 10 mm large balsa rib in the
rudder with fast epoxy
Position 4 hinges and glue them with a lot of epoxy.
Servo location:
You have 2 possibility : Fit the rudder on one side of the rudder or fit the servo in the bottom of the
rudder.
Servo in the bottom :
Servo is on the bottom of the rudder on 2 plywood mounts
Servo is directly connected to the rudder (no link)
Servo is a 25 kg.cm
17
Servo in the rudder :
Servo is fitted in one side of the rudder
Access of the servo is from the bottom of the rudder (to be open)
Servo is a 12 kg.cm with M3 link
18
INLETS
Sand the inlet edge and air intake edge to remove loose fibers.
Put the inlets in the fuselage. The inlets should jut out over the air intakes by a few mm.
Remove the inlets from the fuselage and apply some epoxy to the inlets and the air intakes.
Put the inlets in the fuselage.
Put some clothes pegs on the edges of the inlets in the fuselage and in the air intakes.
Let them dry overnight.
Remove the surplus inlet from the air intakes.
19
Inlet shock cone
Glue the plywood reinforcement in the fiber part.
Glue the shock cone in the middle of the inlet.
Secure it with parker screws from inside the
fuselage
Air tubing :
Connect the air cylinders and retracts according the manual.
Connect the gear door air cylinders according the manual.
Finishing wings :
Sand the internal elevons to have up and down
throws.
Position the 8 scale hinges and fairing and glue
them with CA.
Glue the wing tip pod
20
FUSELAGE HATCH
Glue 2 wood hatch pins with CA.
Glue the hatch latch and drill the corresponding hole in the fuselage.
Glue the plywood reinforcement in the hatch
21
FIBER CANOPY
Cut fiber canopy as engraved.
CLEAR CANOPY
Put fiber canopy inside the clear canopy
Draw with a pen the limit of the canopy.
Cut the canopy as drawn
22
CANOPY in one part
Drill 2 hole for the front canopy pin.
Drill one hole for the hatch latch.
Glue with CA the ABS cockpit interior parts and
paint them in black.
Glue the canopy on the canopy frame with ZAP
canopy.
Glue the hatch latch to the fuselage.
23
OPENNING CANOPY
Drill 2 hole for the front canopy pin.
Drill one hole for the hatch latch.
Glue 2
small hatch
latches to
the canopy
frame.
Glue a flat hinge to the rear of the canopy frame
Make a slot in the fuselage for the hinge.
Glue the 2 canopy on the 2 canopy frames with ZAP canopy.
24
Cockpit detail kit :
Assemble the ejector seat as the photo :
Cut the vacuum parts as shown
Glue with CA the 2 vacuum parts and the 2 plastic
parts according to the plan.
Glue with CA the plastic part at the rear of the
ejector seat.
Fit all the part in the cockpit
Fit the instrument panel and HUD.
Fit the ejector seat in the cockpit.
25
26
NOSE CONE
Fit 4 screw at 90° in the nose cone
Make 4 corresponding slots in the nose
Just secure the nose for flying
There must be nothing in the nose for correct CG
TAILPIPE EXHAUST
Fit the exhaust in the plane
Put 3 screws at 90° on the front frame to hold it
27
TAILCONE
You can fit the standard fiber tailcone of the special scale aluminium variable section exhaust cone
The fiber cone, just fix it at the rear of the plane
The aluminium one, you have to cut the rear fuselage to fix it to the rear plywood frame
AFTERBURNER LED
Just hold the led afterburner with 3 plastic bracket
28
Missiles
If you want to install the missiles under the wings, you have to glue some blind nuts in the wings at the
correct location engraved on the wings.
29
FINISHING TIPS
Now you have to remove the wax from all the parts to paint.
The best way to do this is to sand all the surfaces with a "scotch brit" scouring pad used to wash up the
crockery
All the parts can also be sanded with #400 grit paper to remove wax.
ABS and plastic parts (details set)
All the parts can be glued with CA
30
Installation of the TURBINE.
The turbine is just screwed with 4x 3mm diameter screws on the plywood mount.
The engine exhaust cone should go inside the exhaust pipe from about 2 cm .
The fuel pump is fitted on one side of the fuselage just in the fuselage hatch.
The ECU and valves can be in front of the engine on a plywood plate
The engine battery is in front of the fuselage.
31
Fuel tank
Fuel tank is held between 2 plywood frames
Rear frame should be glued in the fuselage between the 2 inlet ductings
Connect the fuel tank to the clunk as the photo.
Check that there is no leak before to fit it in
fuselage.
Drill a 3 mm hole in the bottom of the fuselage
for the fuel vent
The fuel tank is connected to the UAT catch tank
to be sure that there is no bubble in the fuel line.
The tubing from the main tank to the catch tank
and to the catch tank to the fuel pump must be
gasoline tubing (no silicone tubing). Also for the
air vent tube.
The catch tank is glue with double face tape or with rubber band on
the top of the main tank or on one side.
Hold the fuel tank with rubber bands or silicon glue
Fuel vent
32
Do not apply primer on the fuselage, wings and fin.
They must be directly painted.
Think light : excessive paint build-up will add unnecessary weight to the model. Apply light, thin coats of
paint and sand between coats to avoid excess weight.
Radio installation :
The Mirage needs a minimum of 5 good servos :
For the elevons, we strongly recommend to fit 4 servos (30 kg.cm torque) : 2 servos per wing
NG steering : 1 servo 9 kg torque
Retract + gear doors + brakes : 3 electrovalves
Fit the radio in the nose section with batterie.
Adjust batterie position to have to correct CG
position.
Don’t put the receiver and aerial antenae too
close the the ECU
Retract valve and brake valve can be fitted as
the pics
We also recommand the use of a Power box
system or similar system required for the big
number of high torque servos
You also need 1 electronic mixers on your
radio.
You must mix the 2 elevons like a delta.
When you pull the stick back, the trailing edge of the elevons should go up.
Recommended surface throws :
Ailevons in pitch :
Up : 56 mm Down : 25 mm
Up : 35 mm Down : 25 mm
for take off
for normal flight
Ailerons in roll :
20 mm left and 20 mm right
Exponential: 50
Exponential: 50
Exponential: 20
All measured in the widest part of the surface
33
Center of gravity
You normally need 2 x 4000 Mah battery + ECU battery in the nose to have a correct Centre of
Gravity.
412 mm
486 mm
Note : balance the model with the gear down and the tanks empty.
The center of gravity (CG) must be located at 486mm rear of the wing leading edge . It is the
maximum rear position
You can use 470 mm as forward position
You must check it before the first flight, to do this with the aircraft in flight condition but without
fuel lift the aircraft in this point, the aircraft must adopt a horizontal attitude. If the tail drops
move the batteries forward or add weight in the nose.
In other hand if the nose drops considerably add weight in the tail or put batteries backward.
Total weight
The total weight of the MIRAGE 2000 is 20 to 21 kg tanks empty.
Important note : Pay very careful attention to structural integrity. This jet can reach speeds
of over 400 KPH - 250 MPH. It is your responsibility to operate it safely.
Specifications may change without notice.
34