Woods PRD6000, PRD7200, PRD8400 Installation manual

for LS72 Loader
on Cub Cadet® Tractor
SC2400
(8/15/2008)
MAN0728
includes Hose Kit
1029395
HIS
T
E
!
SAV NUAL
MA e it with ual.
an
ud
Incl ader M fety,
r Lo ains sa epair
u
o
y
nt
dr
It co tion, an ation
m
r
ra
ope rt infor in othe
pa und
fo
ls.
not manua
Tested. Proven. Unbeatable.
INSTALLATION MANUAL
2100042
LOADER MOUNTING KIT
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’s
Manual are completed before releasing equipment to the owner.
TO THE OWNER:
Read this manual and Loader Operator’s Manual before operating your Woods equipment. The information presented
will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read
this manual carefully and become acquainted with all adjustment and operating procedures before attempting to
operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer
Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number of your equipment in the space provided.
Model: _______________________________
Date of Purchase: _____________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.
2 Introduction
LMK (Rev. 7/20/2007)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
!
LEA EL INSTRUCTIVO!
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of
personnel involved in the operation, transport,
maintenance, and storage of equipment.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be
that kind of operator.
INSTALLATION
„ This Loader Mounting Kit is to be used only for
the loaders and tractors specified in this manual.
Any other use or modification of this mounting kit
may result in serious injury or death.
„ Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
„ After connecting hoses, check that all control
lever positions function as instructed in the Operator's Manual. Do not put into service until control
lever and equipment movements are correct.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
„ Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it
Loader Mounting Kit SR3 (4/25/2003)
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CONTACT A P HYS ICIA N IM ME DIATE LY IF FLU ID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
„ Air in hydraulic systems can cause erratic operation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
p ut t i ng i n t o s e r v i c e o r a l l o w i n g a n y o n e t o
approach the equipment.
„ Protective hose sleeves must cover all hydraulic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
„ Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its components in any way.
„ Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.
„ Use a suitable lifting device of sufficient capacity. Use adequate personnel to handle heavy components.
„ Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
Safety 3
LOADER MOUNT INSTALLATION
WARNING
■
Only use 2100042 Loader Mounting Kit for
mounting Woods LS72 loader on Cub Cadet®
SC2400 tractors. Any other use or modification of
this mounting kit may result in serious injury or
death.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replacement manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-3196637.) Failure to follow instructions or safety rules
can result in serious injury or death.
CAUTION
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
NOTICE
■
This equipment must be assembled and
installed on the customer’s tractor by the Woods
dealer. Dealer must thoroughly inspect equipment
and complete each item on the PRE-DELIVERY
CHECK LIST, DELIVERY CHECK LIST, and PRODUCT REGISTRATION before equipment is released
to the customer.
Tractor Preparation
NOTICE
■
Clean threaded holes in the tractor chassis thoroughly using a tap of the proper size. Paint, rust, or
debris in the threads may not permit cap screws to
be installed and tightened correctly.
For installing this mounting kit, references to right, left,
forward, and rearward directions are determined from
the operator’s position in the tractor seat.
NOTE: Leave all loader mount hardware loose until
mount is completely installed or other wise specified.
1. Shut off engine and set parking brake during installation.
2. Remove the tractor front weights and weight bracket
if equipped.
As a valued customer, Woods appreciates your comments. Once loader mount and
hydraulic hoses have been installed, please take a few minutes to complete the Loader
Mount Evaluation sheet that was supplied with this mount. Your comments will help us
continue to bring you quality products.
4 Mount Installation
MAN0728 (8/15/2008)
Attach Right and Left Mounts
1. Attach right mount (1) to tractor frame using five
cap screws (6) and hardened flat washers (5).
NOTE: If tractor is equipped with an undermount
mower, attach mower lift stop link (3) over the rear
two mounting holes. Secure using two cap
screws (4) and hardened flat washers (5).
1
6
5
2. Repeat steps to install left mount (2).
3. Torque hardware to:
M16 x 2.0P . . . . . . . . . . . . . .125 lbs-ft (169 N-m)
1. 1029390 Right rear mount
2. 1029391 Left rear mount
3. 1029443 Mower lift stop
4. 307429 M16 x 2.0P x 55 mm HHCS
(used with item 3 only)
5.
57817 5/8 Hardened flat washer
6.
64062 M16 x 2.0P x 40 mm HHCS
DP1
Figure 1. Right Mount Installed
Figure 2. Mount INstallation
MAN0728 (8/15/2008)
Mount Installation 5
Install Grill Guard
1. Attach grill guard mounting brackets (B) to the
right and left sides of the tractor frame. Secure to
each side using two cap screws (C), hardened flat
washers (D), and hex nuts (E).
2. Slide grill guard (A) over outside of mounting
brackets and insert lower bar into slots.
3. Secure into position using two (one per side)
clevis pins (F) and klik pins (G).
4. Remove grill guard (A) whenever hood is raised
for maintenance.
5. Torque the cap screws (C) in the tractor frame to
85 lbs-ft (115 N-m).
A.
-------- Grill guard
B. 1029397 Mounting brackets
C.
3379 1/2 NC x 1-1/2 HHCS GR5
D.
57816 1/2 Hardened flat washer
E.
1093 1/2 NC Hex nut
F.
16120 3/8 x 1-1/4 Clevis pin
G.
22411 3/16 x 1 Klik pin
Figure 3. Grill Guard Installation
6 Mount Installation
MAN0728 (8/15/2008)
1029395 HOSE KIT
General Description
These instructions are for operating the loader using
the tractor hydraulic remote control lever. To use this
hydraulic connection, the tractor must be equipped
with the manufacturer’s multi-function hydraulic lever
and four tractor hydraulic couplers (Figure 4).
NOTE: Completion of this installation requires connection to the loader.
DP1
Figure 4. Tractor Hydraulic Remote Connection
Assemble Hoses
NOTE: Use thread sealant on all pipe thread connections and tighten securely to prevent leaks.
1. Attach male quick couplers (2), adapters (3) and
a colored band (4-7) to each loader supply hose
(1).
2. Connect loader supply hoses to loader steel
feedlines on right side of loader as shown in
Figure 6.
1. 1007758 Hose, 46” x 9/16 JICM x 9/16 JICF
2. 316013 Quick Coupler, Male 1/4 NPT
3. 315061 Adapter, 9/16 JICM x 1/4 NPTM
4. 395061 Plastic band, red
5. 395062 Plastic band, band
6.
56061 Plastic band, green
7.
56062 Plastic band, yellow
Figure 5. Hose Connections
Figure 6. Loader Feedline Connection
MAN0728 (8/15/2008)
Installation 7
Connect Hoses
1. Route hydraulic hoses along loader mount and
connect to tractor hydraulic couplers, located
under right side of operator’s platform. See Figure
7.
2
3
2. Be sure to avoid contact with clutch pedal and
other moveable tractor components.
NOTE: Hoses must be routed so that they are not
pinched, bent sharply, or chafed during operation.
Hoses must not interfere with any tractor control
operation or contact any moving parts.
3. Secure hoses together using plastic hose ties
supplied in hose kit.
1
4
Figure 7. Tractor Hydraulic Remote Connection
Figure 8. Remote Couplers and Loader Feedline Connections
8 Installation
MAN07/28 (8/15/2008)
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
2. Connect loader feedline hoses to tractor hydraulic
remote control hydraulics couplers. See Figure 8
for hose connections.
3. Comply with all Safety Rules and start the tractor.
4. Mount loader to tractor by activating bucket
cylinders to raise or lower the loader uprights into
the loader mounts. Slowly advance tractor
forward, activating appropriate cylinders to
engage loader completely into mounts. Insert
mounting pins to secure loader.
5. Check that all hydraulic control lever positions
operate the loader movements correctly as
shown in Figure 9.
●
●
●
●
●
Handle Forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
Handle to right - Dump bucket or attachment
Handle to left - Rollback bucket or attachment
Figure 9. Single Lever Control Operation
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be
correct before proceeding.
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic
system and check oil level.
8. When hose routings and correct loader
operations are verified, identify each circuit by
placing a matching colored band around the male
and female quick couplers. The color-coded
bands will make reinstallation easier when the
loader is removed from tractor.
9. Before operating the loader, make sure that
the Pre-Delivery, Delivery, and Pre-Operation
Check Lists in the Loader Operator’s Manual
have been completed.
MAN0728 (8/15/2008)
Installation 9
2100042 LOADER MOUNTING KIT
REF
PART
QTY
DESCRIPTION
REF
PART
QTY
1
1029390
1
Right mount
A
-------
2
1029391
1
Left mount
B
1029397
3
1029443
2
Mower lift stop link
C
4
307429
4
M16 x 2.0P x 55 mm HHCS
(used with item 3 only)
D
5
57817
10 5/8 Hardened flat washer
F
16120
6
64062
10 M16 x 2.0P x 40 mm HHCS
G
22411 *
7
1029396
1
E
3379 *
57816
1093 *
DESCRIPTION
Grill guard
2
Grill guard mounting bracket
4
1/2 NC x 1-1/2 HHCS GR5
4
1/2 Hardened flat washer
4
1/2 NC Hex nut
2
3/8 x 1-1/4 Clevis pin
2
3/16 x 1 Klik pin
Grill guard kit (includes items A - G)
* Standard hardware, obtain locally
HHCS Hex Head Cap Screw
10 Parts
MAN0728 (8/15/2008)
1029395 HOSE KIT
REF
PART
QTY
DESCRIPTION
1
1007758
4
Hose, 46" x 9/16 JICM x 9/16 JICF
2
316013
4
Quick coupler, 1/4
3
315061
4
Adapter, 9/19 JICM x 1/4 NPTM
4
395061
1
Plastic spiral band, red (NS)
5
395062
1
Plastic spiral band, blue (NS)
6
56061
1
Plastic spiral band, green (NS)
7
56062
1
Plastic spiral band, yellow (NS)
4
Plastic tie (NS)
8
88 *
NS Not shown
* Standard hardware, obtain locally
MAN0728 (8/15/2008)
Parts 11
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
1/4"
5/16"
7/16"
1/2"
6
12
8
17
10
19
13
26
14
27
18
37
3/8"
7/16"
9/16"
5/8"
23
36
31
48
35
55
47
75
49
78
67
106
1/2"
9/16"
3/4"
13/16"
55
78
75
106
85
121
115
164
120
171
163
232
5/8"
3/4"
15/16"
1-1/8"
110
192
149
261
170
297
230
403
240
420
325
569
7/8"
1"
1-5/16"
1-1/2"
306
467
416
634
474
722
642
979
669
1020
907
1383
A
METRIC SERIES
TORQUE
CHART
A
Metric Bolt Head
Identification
8.8
Metric
Grade 8.8
10.9
Metric
Grade 10.9
COARSE THREAD
FINE THREAD
MARKING ON HEAD
MARKING ON HEAD
A
Diameter &
Thread Pitch
(Millimeters)
Wrench
Size
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
N-m
lbs-ft
Diameter &
Thread Pitch
(Millimeters)
6 x 1.0
10 mm
8
6
11
8
8
6
11
8
6 x 1.0
8 x 1.25
10 x 1.5
13 mm
16 mm
20
39
15
29
27
54
20
40
21
41
16
30
29
57
22
42
8 x 1.0
10 x 1.25
12 x 1.75
14 x 2.0
18 mm
21 mm
68
109
50
80
94
151
70
111
75
118
55
87
103
163
76
120
12 x 1.25
14 x 1.5
16 x 2.0
18 x 2.5
24 mm
27 mm
169
234
125
172
234
323
173
239
181
263
133
194
250
363
184
268
16 x 1.5
18 x 1.5
20 x 2.5
22 x 2.5
30 mm
34 mm
330
451
244
332
457
623
337
460
367
495
270
365
507
684
374
505
20 x 1.5
22 x 1.5
24 x 3.0
30 x 3.0
36 mm
46 mm
571
1175
421
867
790
1626
583
1199
623
1258
459
928
861
1740
635
1283
24 x 2.0
30 x 2.0
Typical Washer
Installations
Bolt
Metric 8.8
Lock Washer
Metric 10.9
Metric 8.8
Metric 10.9
Flat Washer
8/9/00
12 Appendix
Bolt Torque & Size Charts (Rev. 3/28/2007)
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
IN
MM
5/8
3/4
7/8
1
2
3
4
5
6
7
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM
10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
ASABE.................... American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE ....... American Society of Agricultural Engineers
ATF ............................... Automatic Transmission Fluid
BSPP .............................British Standard Pipe Parallel
BSPTM ................ British Standard Pipe Tapered Male
CV.....................................................Constant Velocity
CCW .............................................. Counter-Clockwise
CW............................................................... Clockwise
F ...................................................................... Female
FT .............................................................. Full Thread
GA .................................................................... Gauge
GR (5, etc.) ........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT ........................................................... Heat-Treated
JIC .................Joint Industry Council 37° Degree Flare
LH .................................................................Left Hand
LT........................................................................... Left
m......................................................................... Meter
mm................................................................ Millimeter
M.......................................................................... Male
Bolt Torque & Size Charts (Rev. 3/28/2007)
MPa......................................................... Mega Pascal
N.......................................................................Newton
NC ...................................................... National Coarse
NF ...........................................................National Fine
NPSM..................... National Pipe Straight Mechanical
NPT .......................................... National Pipe Tapered
NPT SWF ......... National Pipe Tapered Swivel Female
ORBM .......................................... O-Ring Boss - Male
P...........................................................................Pitch
PBY ...................................................... Power-Beyond
psi.......................................... Pounds per Square Inch
PTO ..................................................... Power Take Off
QD ....................................................Quick Disconnect
RH ..............................................................Right Hand
ROPS ........................... Roll-Over Protective Structure
RPM ........................................Revolutions Per Minute
RT ....................................................................... Right
SAE ..........................Society of Automotive Engineers
UNC ..................................................... Unified Coarse
UNF...........................................................Unified Fine
UNS...................................................... Unified Special
Appendix 13
WARRANTY
(All Models Except Mow’n Machine
TM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
From (Dealer): ___________________________________________
Model Number: ____________________________
Serial Number: ___________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set
forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
Woods backhoe models BH70-X, BH80-X, and BH90-X are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Model Number
BW1260, BW1800
Duration (from date of delivery
to the original purchaser)
8 years
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X,
6 years
BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3
Gearbox
components
PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2,
RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2, 9180RD-2, 5 years
9204RD-2, S15CD, S20CD, S22CD, S25CD, S27CD
RDC54, RD60, RD72
3 years (1 year if used in rental or
commercial applications)
Blade spindles
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400, 7144RD-2,
3 years
9180RD-2, 9204RD-2
Rust-through
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW180-3,
10 years
BW1260, BW1800, 2162, 3240, DS1260, DSO1260, DS1440, TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made
with parts other than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to
a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS,
in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof
of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS
WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute
machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS,
its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-3079 (Rev. 5/15/2008)
WARRANTY
(Replacement Parts For All Models Except Mow’n MachineTM
Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
PART NO.
MAN0728
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
www.WoodsEquipment.com
© 2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.