C3 RS915 OP revised - Remotely Started MN

C3-RS-915 LCD
PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & ALARM
SYSTEM
With
Built in Temperature & Voltage Sensor
And Two-way Serial Port Data Link
Compatible
OPERATION MANUAL
Please register your product at:
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
1
Congratulations on your purchase of the RS -915 LCD remote start vehicle security system. We sincerely
hope the purchase of the RS -915 remote start security system gives peace of mind to you.
The RS-915 LCD is a state-of-the-art two-way communication system. Please take the time to read over this
manual to thoroughly familiarize your self with the many features and options of the RS-915 LCD .
WARNINGS:
As with any product that performs automatic functions, there are certain safety precautions that you must
practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. The vehicle windows must be rolled up.
7. Should the unit malfunction, disconnect the fuse until the problem is corrected.
8. The use and operations of this system is the sole responsibility of the operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.
10.It is not safe to remote start the vehicle if the vehicle is parked on a steep incline.
LCD REMOTE CONTROL TRANSCEIVER: XT-74 LCD
A. BATTERY CHARGING:
This system has a built in rechargeable power source. Please charge the battery fully with the
supplied charger before initial use. Depending on the usage, the remote should be charged at least
once a month. Do not use other chargers on this remote as they could damage the rechargeable
batteries. The 1-way remote is powered by a pair of 3V, CR2016 batteries.
Battery Level Indicator (2 -way remote)
The Battery Level indicator has three level indicators that serve as a visual indication of battery
charge. When the battery reaches a low charge level that requires charging, the remote control will
generate a single notification chirp, and the Battery Level indicator
will flash continuously.
C3 RS915 REV. O1
2
B. STANDARD LCD ICON CONFIGURATIONS:
12:00
The lock icon will be displayed when the
door locked.
The unlock icon will be displayed when
the door unlock
Sensor Bypass
Sensor 1 bypass under Arm mode
Hidden Alarm Mode
The security system arm with hidden
alarm function (silent alarm)
Valet Mode
Remote start and alarm functions shall
be temporarily on hold.
Hood Trigger
Hood is illegally opened (Zone 1)
Trunk Trigger
Trunk is illegally opened (Zone 2)
Door Open Warning
Doors are illegally opened (Zone 3)
Sensor Trigger
Trigger on Sensor 1 (Zone 4)
Ignition Trigger
Ignition switch is illegally turned on (Zone
5)
System trigger
Remote Transmission
You are transmitting the signal to control
unit
In – Range Indicator
You are within the range of the remote
control.
Anti Car-Jack Mode
Activate the anti car-jacking mode
Icon flash under check mode
Engine Cranking
Your vehicle engine Cranking by remote
control
Engine Running
Your vehicle's engine is running
Timer Control Start
Engine start automatically every 2 or 3
hours.
Temperature Start
Engine start automatically when reach
programmed temperature.
Daily Start
Engine start automatically at the same
time next day
Turbo Timer
Turbo timer was set up
Manual Gear
Engine Start Memorizing for the car with
manual gear was set up
Activate Channel 3 (Trunk Release).
Activate Channel 3
Activate Channel 4
Time Monitor
12:00
Parking Meter
Reminder when time is up for parking
C3 RS915 REV. O1
3
Alarm Clock
You have set morning call alarm
Low Battery
You have to charge the battery of remote
control.
Melody Mode
Remote Control alert user through
melody sound
Vibration Mode
Remote Control vibrates when the
system is triggered
OPERATION:
REMOTE TRANSMITTER OPERATION:
C:
Transmitter
Button
System Function
Remark
Lock Doors & Arm System
Press and Hold for 3 seconds . Press Trunk
button to stop panic function
Press when in armed mode
Panic function
Car Locator
-
Arm and Delete The 2 Stage Shock
Sensor
-
Arm System and Hidden Alarm Function
+
Silent Arming / Disarming
+
Active Anti Car-Jacking Mode
Unlock Doors & Disarm System
Two Steps Door Unlock & Disarm
System(optional)
Trunk Release (Channel 3)
Passive Arming By-pass
-
Activate or Turn Off The Remote Start
Channel # 4 Timer Output (4)
Channel # 5 Timer Output (5)
+
+
Press
twice within 3 seconds. Pass will appear
on the remote
Press within 3 seconds and Hold
button for 2 seconds
Ignition in "off" position.
Ignition in "on" position press and hold for 2
seconds
Press twice within 3 seconds.
Press and Hold for 2 seconds
While the system Disarmed.
Press button once.
Press Twice if set to start
safety mode
Optional
Channel # 6 Timer Output (6)
+
II
Switching code For 2nd Car Operation.
D CHIRP INDICATORS:
Chirp
1 chirp
For regular XT-33 remote transmitter Only
PARKING LIGHT:
Function
Parking light
Function
Arm
Disarm
1 flash
Arm
Disarm
2 chirps
3 chirps
Defective Reminder
2 flashes
3 flashes
4 chirps
Disarm / Triggered
12 flashes
Car Locator
6 chirps
Car Locator
Constant On
Under Remote Start
Disarm / Triggered
ALARM OPERATING CONDITION:
1. Arming
2. Disarming
Siren / Horn Parking Light
1 or 3 Chirps
1 Flash
2 or 4 Chirps 2 or 3 Flashes
C3 RS915 REV. O1
LED
Slow Flash
Doors
Locking
Unlocking
4
Starter
Disable
Dome Light
Turns on for 30
3. Trigger
4. Passive
Starter
Disable
5. Panic
6. Car-Jacking
Alarming
Flashes
Alarming
Alarming
Flashes
Flashes
7. Car Locator
6 Chirps
12 Flashes
Slow Flash
Disable
Fast Flash
Disable
Disable
-second
Flashes
Flashes
Flashes
Locking
E. ACTIVE ARMING – LOCK & ARM:
1. Press
button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The
vehicle’s doors will lock upon arming if interfaced with the security system.
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid
ajar.
SILENT ARMING / DISARMING: Press the transmitter
and
buttons at the same time. This will arm or
disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the
vehicles parking lights only.
SENSOR BY-PASS:
The sensor bypass feature is programmed to activate for one arming cycle only. The security sys tem will
return to normal operation during the next arming cycle.
Sensor By-Pass : Press the
button two times within 5 seconds will arm the security system and
by-pass the shock sensor.
HIDDEN ALARM FUNCTION: Silent Alarm
Press the
button first; within 3 seconds press the
button to activate the hidden alarm function. The
security system will arm and with “Hidden Alarm Function” The siren / horn will be silenced even if the
sensor is triggered in the armed mode. Alarm indication will only appear on the LCD Transmitter.
F. PASSIVE ARMING (Programmable)
Active arming / disarming is controlled by your security system via the remote transmitter. This security
system is equipped with an optional Passive Arming feature which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any
door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.
3. After the 30-second time has elapsed, the security system will automatically “ARM”. The siren will chirp [1]
time and the parking lights will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after the passive arming cycle has been completed.
PASSIVE ARMING BY -PASS: While the system is disarmed, Press the
button twice, the system will respond
with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as long as you wish.
To exit passive by-pass, press the transmitter
or
buttons and the system will return to normal status.
G. ACTIVE DISARMING – UNLOCK & DISARM:
1. Press
button on the transmitter.
C3 RS915 REV. O1
5
2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed.
The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door
locks and dome light must be installed with the security system.)
TAMPER DISARMING: If the alarm is triggered , upon disarm the system’s siren will chirp 4 times, and the
parking lights will flash 3 times telling you the alarm has been triggered during the last armed state.
PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this feature will turn the parking lights
“ON” for 30 seconds and for 10 seconds upon the lock signal. (Programmable)
TWO STEPS DOOR UNLOCK (Optional): This feature will independently unlock the driver’s door only when
disarming the security system. Pushing the
button a second time within 3 seconds will unlock the other
doors.
AUTOMATIC RE-ARM: If this feature is selected, the security s ystem will automatically re-arm itself in 60
seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before
the 60 seconds timer has elapsed.
H. DISARMING WITHOUT A TRANSMITTER
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:
(Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to the 'ON’ position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter the disarm
mode. You can now start and operate the vehicle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
Unlike valet switch that can easily be found and defeated, this security system allow s the consumer to
program a password pin code offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet Switch. (When
finished above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle
can’t be started.)
3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF” and then
“ON”.
4. Within 15 seconds, enter your chosen second digit code by pressing and releasing the Valet Switch.
5. Turn the ignition switch “OFF” position. 4 Chirps from siren/horn and 3 flashes from the parking light
indicate the system has disarmed.
Note: You must override the alarm within 60 seconds. If not, the system will automatically re-arm.
EXAMPLE: To Override the System with the Password Code 83,
1. Enter the vehicle and turn the ignition switch to the 'ON’ position.
(Alarm will sound.)
2. Within 5 seconds, Press and Release the Valet Switch 8 times, (When finished the system's siren will
stop alarming, lights stop flashing, but the vehicle cannot be started or driven away.)
3. Within 15 seconds of entering the last digit code enter (the 1st code), turn the Ignition Switch “Off” and then
“ON”.
C3 RS915 REV. O1
6
4. Within 15 seconds, Press and Release the Valet Switch 3 times.
5. Turn the Ignition Switch to the “Off” position. 4 Chirps form siren/horn and 3 flashes from the parking lights
will indicate the system has disarmed.
I.
VALET MODE:
VALET MODE: (System is in Disarm Mode )
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm
functions and remote start functions are bypassed, however, the remote panic feature and remote door
locks will remain operational. To use the valet mode, the system must first be disarmed either by using your
remote transmitter, or by operating the Manual Override sequence.
Get into/out valet mode using the ignition key.
Enter Valet Mode:
a). Under disarm mode, turn the ignition to “ON” position.
b). Press and hold valet switch for 2 seconds until the LED turns ON solid. The LED will remain on as
long as the system is in 'valet mode'.
Exit Valet Mode:
a). Turn ignition 'ON'.
b). Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the
valet mode.
J. CAR LOCATOR
Under armed mode, press the
button to active car locator function. The siren will chirp 6 times. The
parking light will flash 12 times, for you to easily locate your car.
K. PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.
1. Press and hold the
button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter
and
buttons can be used to lock and unlock the door (if the option is installed), however once the
button is
pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start.
3. To stop the alarm, press the trunk
button on the remote control
4. If the button is not pressed, the alarm will autom atically stop after 30 seconds.
L. TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning on the ignition key
will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn, parking
lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and automatic
reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will sound a
maximum of 3 times of 30 seconds cycles.
NOISE ABATEMENT CIRCUIT: Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive
trigger sequences due to faulty door pin switches or environmental conditions such as thunder,
jackhammers airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor
or switch has triggered the alarm; the “Noise Abatement Circuit” will interpret this pattern of triggers as a
C3 RS915 REV. O1
7
false alarm. After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses, that sensor or switch
until a different sensor or switch is trigger.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door
for Three full cycles, the doors will be bypassed until the trigger ceases.
M. ANTI CAR- JACKING (Programmable)
Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature
“OFF”. This systems default setting is “OFF” for all carjacking modes.
ACTIVE ANTI CAR JACKING:
1.When the Ignition is ON press F button four times while “CAR JACK” is flashing in the text area, then
press
button to activate Anti Car-Jacking mode or
Under ignition ON , press and hold the
and
buttons at the same time for 2 seconds. The parking
lights will turn on for 1.5 seconds to indicate the system has entered the anti car-jacking mode.
2. Once the system in anti car-jacking mode, the system will be triggered when any door is opened and
closed while the ignition is “ON”.
PASSIVE ANTI CAR- JACKING: (Programmable)
It will operate as noted below:
1. Turn the ignition switch to th e “ON” position and the system will arm.
2. Once the system is armed, if you are forced from the vehicle, the system will trigger when the door is
opened and closed while the ignition is “ON”.
TRIGGERING THE ANTI CAR -JACKING MODE:
A). 50 seconds after the s ystem has been triggered. The siren will start chirping for 15 seconds.
B). During this 15 second period of chirping, you will be alerted to push the valet switch once to turn off the
car-jacking feature. If not, it will enter a second timer for carjacking.
C). 65 seconds after the system has been triggered, the siren will start sounding and the parking lights will
start flashing.
D). 90 seconds after the system has been triggered,
1. The siren will sound and the parking lights will flash, and
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power is exhausted.
OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the
system disarmed
Note: If you use password pin code to double protect the vehicle security, you will need to use it to completely
disarm the system.
N. SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
Press and hold F button of LCD remote until 3 beeps sound , release and re-press F button again, the
LCD remote will show “ALARM “ icon flash on text area (see advanced users mode), then press
button to activate system trigger check.
Note: If the system has no response then you are out of range.
O. SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
Press F button of LCD remote until 3 beeps sound , the LCD remote will show “STATUS “ icon flashing
in the text area (see advanced users mode), then press
button to activate system status check.
It responds with one melody sound and all vehicles’ status records will immediately displayed on the LCD
screen.
Note: If it has no response then you are out of range.
C3 RS915 REV. O1
8
P. DRIVER PAGING / LOST & FOUND (For two-way transceiver operation only)
This feature is useful the event that someone wants to page the driver of the parked vehicle or someone
cannot find his LCD remote transceiver.
Under the ignition switch “OFF” condition, press and hold the valet switch for 2 seconds to page the driver,
one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from
the Remote LCD transceiver.
Q. DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)
The alarm has a unique feature that will turn on your vehicle dome light as follows:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turning on the ignition switch or arming the alarm will turn off the dome light.
R. IGNITION CONTROL DOOR LOCK/UNLOCK. (Programmable Feature)
If the vehicles door locks have been interfaced to the security system, the system will automatically lock the
vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is
turned “OFF”. (Default setting is “OFF”)
S. TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold
button on the transmitter for two seconds to remote ly control the trunk release.
T. CHANNEL 4.5.6 TIMER CONTROL OUTPUT.
CHANNEL 4 TIMER CONTROL OUTPUT.
Press the transmitter
and
buttons at the same time to active Channel 4 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and re-press F button the LCD
remote will show “CH 4” icon flash, then press
button to activate channel 4 function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal
for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on
the headlight, power window or sunroof. (Factory defaults setting at momentary output.)
CHANNEL 5 TIMER CONTROL OUTPUT.
Press the transmitter
and
buttons at the same time to active Channel 5 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and re-press F button the LCD
remote will show “CH 5” icon flash, then press
button to activate channel 5 function.
Channel 5 is user-programmable timer output. You may program the built-in timer to send a ground signal
for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on
the headlight, power window or sunroof. (Factory defaults setting at momentary output.)
CHANNEL 6 TIMER CONTROL OUTPUT.
Press the transmitter
and
buttons at the same time to active Channel 5 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and re-press F button the LCD
remote will show “CH 6” icon flash, then press
button to activate channel 6 function.
Channel 6 is user-programmable timer output. You may program the built-in timer to send a ground signal
for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on
the headlight, power window or sunroof. (Factory defaults setting at momentary output.)
C3 RS915 REV. O1
9
U. POWER SAVER MODE (Default OFF) * See advanced user mode
Under Menu mode press
button while “POWER SAVE” icon flash, press
button Power save ON,
while the power save mode, the LCD remote transceiver use “0” current to save the battery power.
Press
button Power save OFF
Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”.
V. POWER ON MEMORY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the
power is lost and then reconnected.
W. SECOND VEHICLE SECURITY OPERATION:
Your 5-button remote transmitter can be utilized to control a second vehicles security system, To program
the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming.
* For the standard transmitter ( II) is shift button.
Standard Transmitter
1. Prior to pushing any button on the transmitter. Press the Select II button first on the transmitter.
2. Once II button is pressed the LED on the transmitter will illuminate for 3 seconds to indicate the second
transmitter pin code has built-in.
3. While the LED is illuminated, press any button on the remote control transmitter to control a second
vehicle security system.
4.
nd
For LCD trans ceiver – 2 car operation :
a. Press and hold F button of LCD remote for 1 second until 2 beeps sound and then release the F button.
b. The text
will flash on the LCD screen, press
button to enter the menu.
c. Press
or
button to move up or down in the menu, find CAR SELECT on the menu.
d. Press
button to select the option you would like to adjust CAR 1 or CAR 2 for further operation.
Caution: If the LCD transmitter does not function. Please insure it is set to operate car #1
X. Clear the Flash Icon and Melody Sound: The Transmitter will reset the flashing icons the
next time the Ignition is cycled to the ON position.
Y. Stop The Trigger Melody Sound:
While triggering the alarm the LCD screen will alert the user
through a melody sound and a flashing trigger icon. Press any button on the LCD remote transmitter to stop
melody sound only.
Z. Vibration / Melody Mode: (see advanced users menu for more info)
Press and hold the F button until 2 beeps are heard. You will see the word
.Press the trunk button
scroll through the menu. Scroll to the word “
Vibrate”. When you see the word “Buzzer Vibrate”,
press the trunk button once to enter programming . Press the
button to change the setting. (Buzzer, BZ VIB,
Vibrate). Once a setting is chosen. Press the
button to confirm.
REMOTE START OPERATION:
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button once on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls
will activate and adjust the vehicle’s interior temperature to your preset setting. (While the vehicle is running,
the “minutes” digit on the LCD screen will flash and the will indicate countdown timer based on the 5, 10,
20 or 30 minute run time set up by your installation center.)
C3 RS915 REV. O1
10
to
5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit
shuts off the countdown timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle is switched to the “OFF” position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”.
SAFE START (Child safety mode)
Factory default is set to press the
button once on the transmitter to start the vehicle. You can program this
feature to eliminate an accidental remote start:
1. The user presses the transmitter
buttons twice within 3 seconds to start the vehicl e. or
2. The user presses the transmitter
and
buttons at the same time to start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
B. OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:
To operate the vehicle while the engine is running from the remote start,
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would
like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button once on the transmitter and the LED indicator will flash
3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run u ntil the pre-programmed time elapsed or shutdown input is received.
D. TURBO CHARGE MODE:
Turbo charger mode keeps the engine running after arriving at you r destination for a programmable period
of 1, 3 or 5 minutes, This allows the vehicle’s engine tim e to conveniently cool down the turbo after you have
left the vehicle.
To activate:
1. While the engine is running, pull up the hand brake and place the transmission gear in the park position.
2. Before turning off the engine, press and release
and
buttons at the same time.
-- The LED will flash indicating the remote start has entered the turbo charger mode
LCD remote .
3. Take the “Ignition Key” from the key cylinder.
-- Engine keeps running. -4. Exit and secure the vehicle.
-- Engine continues running until the pre-programmed time elapsed. --
appear on
NOTE: This feature only applies to vehicles with Turbo Charged Engines.
E. TIMER START:
This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next
morning, the engine will run for the programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, never start and run the vehicle in on
enclosed space as a garage or carport. Please be sure you fully understand this feature before use.
Enter timer start:
C3 RS915 REV. O1
11
1. Ignition ON => OFF within 15 seconds Press
button first, within 3 seconds press
2. 3 Hours Timer Start: The parking light will flash (3) times /
times. The vehicle is now programmed to start every 3 hours.
button.
icon appear. The siren or horn chirps (3)
Daily Timer Start: The feature is very useful for the driver who wants to run the vehicle punctually at the
same time next morning. Before set-up of the “Daily Timer Start”, you should set you time for engine
start.( see Timer Setting / Timer set-up for “Daily Timer Start, in Advanced users Mode) Please insure that
you fully understand this feature before programming the timer start mode.
Enter : Ignition ON => OFF, within 15 sec.
1. Press and hold “ F “ button until 3 beeps (you are enter table 3 feature option),
2. Press and release “ F “ button 4 times see
3. then press
button to activate Daily Start.
flash on LCD display,
Cancel timer start:
1. Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. or
2. Press the
button twice to remote start the vehicle.
F. TEMPERATURE CHECK
With the built in temperature sensor you can monitor, Through the LCD screen, the present indoor
temperature of the passenger compartment of your vehicle.
F ” button first until 3 chirps are heard. Then press the F
Press and hold the transmitter “
Button three
more times so that TEMP appears on the remote. Within 3 seconds press
button; the in-door
temperature will b e shown on the LCD screen. This reading may be higher than actual ambient temperature
due to the greenhouse effect and is relative only to the inside vehicle temperature.
G. TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
1. Press
button once on the remote transmitter under the remote start mode.
2. Move the optional remote start enable toggle switch to OFF position. (If installed)
3. Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate the engine has stopped.
H. SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the engine will not start or will shut
down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The parking (hand) brake is released (For Turbo Timer Mode)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Press
button on the remote transmitter under remote start mode.
7. The system trigger.
8. The vehicle refused to start running after {3} unsuccessful attempts.
I. DISABLING THE REMOTE START SYSTEM: (If installed)
This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from
being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an
C3 RS915 REV. O1
12
enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF
position.
ADVANCED USER’S MODE:
C. LCD REMOTE CONTROL TRANSCEIVER OPERATION:
Enter: Press and hold F Button until beep sound respond from LCD transceiver indicate into table 1 – 5
as below.
Exit: Press the
,
or
button to exit this mode.
Table 1: ONE beep to confirm (Press and hold until ONE Beep is heard)
F Button
LCD Display
Press once
Backlight turns on for 5 seconds
Press twice within 5
PASS and
Press
seconds
PASS icon flashing
and bypass the sensor 1.
Press three times
HIDDEN ALARM and
Press
within 5 seconds
icon flashing
Press four times within
Button
button to arm the alarm
button to a rm system and
with Hidden Alarm Function.
Ignition in "on" position press and
CAR JACK and
5 seconds
hold
icon flashing
button for 2 seconds to
activate anti carjacking functions.
Table 2: TWO beeps to confirm (Press and hold until TWO Beeps are heard)
C3 RS915 REV. O1
13
F Button
LCD display
Press and hold the F
MENU flashing
Button
Press
Button for 2 second until
button to enter the menu
mode
2 beeps sounded
Press one more time
CH 4 flashing
Press
within 5 seconds
Press twice within 5
function
CH 5 flashing
Press
seconds
Press three time within 5
button to activate channel 4
button to activate channel 5
function
CH 6 flashing
Press
seconds
button to activate channel 6
function
Table 3:THREE beeps to confirm(Press and hold until THREE Beeps are heard)
F Button
LCD display
Press and hold the F
STATUS and
Button for 3 second until
Button
Press
icon flashing
button to check the Vehicle
Status.
3 beeps sounded
Press ONE more time
ALARM and
Press
within 5 seconds
Press TWO more times
within 5 seconds
Press THREE more
Voltage and
Check icon flashing
TEMP and
times within 5 seconds
Press FOUR more
times within 5 seconds
button to check the system
trigger condition.
icon flashing
Start timer and
Press
button to check the Vehicle
Battery condition.
Press
button to check the Interior
Temperature of the vehicle
Press
button to activate or cancel
daily start.
icon flashing
Table 4: FOUR beeps to confirm (Press and hold until FOUR Beeps are heard)
F Button
LCD display
Press and hold the F
DEMO mode
Button
Press
Button for 4 second until
button to activate Backlight
will be ON until DEMO operation end.
4 beeps sounded
Table 5: Do-Re-Mi sounds to confirm
F Button
LCD display
Press and hold the F
DEFLT flashing
Button
Press & hold
button for 2 seconds
Button for 6 second until
to back to default setting and 1 chip for
Do-Re-Mi sounded
confirm
D. PROGRAMMING LCD REMOTE:
Selecting and Adjusting Menu options:
C3 RS915 REV. O1
14
•
•
•
•
•
•
•
•
•
•
? Press and hold F button for 1 second until 2 beeps sound, then release the F button.
? The text
will flash on the LCD screen, press
button to enter the menu.
? Press
button to move up in the menu or
button to move down in the menu.
? Press
button to select the option you would like to adjust.
? Press
button to increase the value, to activate or deactivate a function or to toggle through
the selection.
? Press
button to decrease the value, to activate or deactivate a function or to toggle
through the selection.
? Press
button to move to the next sub-option or go back to the main menu.
EXIT: Press
button to exit the menu mode.
Order
Menu Option
LCD display
Functions
1
Parking Menu
PARK METER
Default is
- Parking hours
0:30
,
0 is flashing
- Parking
minutes
- Toggle Parking
0:30
,
30 is flashing
+
- Adjusts parking hour
(value from 0 to 2).
- Adjusts parking minute
(value from 0 to 59).
or
countdown
- Enables parking countdown.
There is a beep 5 min. before the Parking
countdown reaches 0.
- Disables parking countdown.
2
Illumination Menu
Default is
3 SEC. or
- Toggle
Illumination Mode 5 SEC . or
OFF
,
Basic operation with backlight
Illumination 3 SEC. or 5 SEC.;
OFF – basic operation without backlight
Illumination.
3
Second Vehicle
Default is CAR 1
Security Operation
Menu
- Car Select
4
CAR 1 or
CAR 2
-CAR 1 operation.
- CAR 2 operation.
Clock Menu
- Clock hours
Default is
12:00AM
,
- Adjusts clock hour from 0 to 12
,
- Adjusts clock minute from 0 to 59
12 is flashing
- Clock minutes
12:00AM
00 is flashing
5
Alarm Clock Menu
- Alarm hours
Default is
12:00AM
,
12 is flashing
C3 RS915 REV. O1
15
- Adjusts alarm clock hour from 0 to 12
- Alarm minutes
12:00AM
,
- Adjusts alarm clock minute from 0 to 59
00 is flashing
- Toggle alarm
6
Back Light Color
ON +
OFF
- Enable alarm clock or
or
- Disable alarm clock
COLOR
Default is COLOR 1
COLOR 1- 7
7
,
Confirmation M enu
- Adjusts color from Color 1 to Color 7
Default is
VIBRTE
- Toggle BZ VIB
+
or
or
+
+
VIBRTE +
8
Button Lock
,
- Buzzer or Vibration
Default is
- Toggle button
- button lock / Disable the transmission
lock
function temporarily
- button unlock / Enable the transmission
Function.
9
Power Save
Default is
- Toggle power
- While the power save mode, the LCD remote
save
transceiver uses “0” current to save the
battery power.
- Power save OFF
Exit: Press any button of the LCD remote
transmitter to exit the “Power Save Mode”.
10
Daily Start Timer
Daily Start Time Adjust Only (ex. 7:30AM)
Setting
- Daily Start Hour
7:30AM
,
- Adjusts clock hour from 0 to 12
,
- Adjusts clock minute from 0 to 59
7 is flashing
- Daily Start
Minute
7:30AM
30 is flashing
To Exit: Do not push any buttons for 15 seconds
C3 RS915 REV. O1
16
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1.
Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the
factory prior to delivery. Your Auto Page equipment is guaranteed for “life” to the original
purchaser/user of the equipment and the original vehicle in which it was installed by an authorized
installer under the following conditions: If the product proves defective (according to Auto Page's
testing) within the first year, the defective unit may be exchanged or repaired free of charge.
“Proof of Purchase” (dated sales receipt) must accompany all warranty returns; otherwise, your
return will be rejected and sent back. After one (1) year, the purchaser should ship the unit
prepaid to Auto Page with a money order in the amount of $30.00 to cover shipping and handling
charges.
Note: The product needs to be registered online at time of installation.
www.autopageusa.com
2.
Exclusion to the Limited Lifetime Warranty Provision: All two-way LCD and two-way OLED
remote transceivers are excluded from the Limited Lifetime Warranty noted in paragraph no.1. All
two-way LCD and two-way OLED remote transceivers are guaranteed to the original purchaser for
a period of one year from date of purchase. If the product proves to be defective within the first year,
the defective unit may be exchanged or repaired free of charge. All other provisions stated on this
card apply.
3.
This WARRANTY will be considered void if the equipment has been misused, neglected,
improperly serviced or installed, altered, dropped or damaged by water, contrary to the Auto Page
OPERATIONS MANUAL. Or, if used with accessories not approved by Auto Page, which may
have contributed to the defect. See note below regarding product installation**.
4.
The purchaser’s remedies under this WARRANTY shall be limited to the repair or replacement of
electronic components only. THE FOLLOWING IS NOT COVERED: Damages or
C3 RS915 REV. O1
17
deterioration to cases, batteries, covers and cabinets; the cost of repairs, replacement and labor of
which shall be borne by the purchaser even if occurring during the WARRANTY period.
5.
Any equipment or parts which are claimed to be defective under this WARRANTY must be sent to
the Auto Page Service center with “proof of purchase” at the purchaser’s expense prior to such
return, a Return Authorization Number should be obtained. Auto Page will return the equipment,
charges prepaid. Warranty Service can be provided through the dealer where the equipment is
originally purchased.
6.
Any unexpired WARRANTY shall be applicable to equipment and parts in the possession of the
original purchaser only.
7.
THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
8.
Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any personal
injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resulting
directly or indirectly from the use or presence of the equipment or parts; Consequential damages of
any kind; any inability of the purchaser to use the equipment.
**IMPORTANT NOTE: Any damages to the Auto Page system resulting from an
installation performed by anyone other than a professional installation
technician authorized by a dealer of Auto Page will void the product’s Limited
Lifetime Warranty.
You must register your product online at http://www.autopageusa.com to receive any warranty service.
Please go to the customer service tab and select product registration.
It is the purchaser’s responsibility to register this product for any future
warranty service.
Warning: Some batteries may contain Perchlorate
What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater,
surface water and soil. Most perchlorate manufactured in the U. S. is used as an ingredient in solid fuel for rockets and missiles.
In addition, perchlorate-based chemicals are also used in the construction of highway safety flares, fireworks, pyrotechnics,
explosives, common batteries, and automobile restraint systems. Perchlorate contamination has been reported in at least 20
states. Perchlorate greatly impacts human health by interfering with iodide uptake into the thyroid gland. In adults, the thyroid
gland helps regulate the metabolism by releasing hormones, while in children; the thyroid helps in proper development.
Perchlorate is becoming a serious threat to human health and water resources.“Perchlorate Material – Special handling may
apply.”For more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
C3 RS915 REV. O1
18
C3 RS915 REV. O1
19
It is recommended to have a minimal digital service plan on your cell phone
Your RS -915 is CI3 compatible and will open your world to the true power of two way communication.
Complete tracking and full cell phone functionality can be added to your system. For more information
please visit your local authorized Autopage dealer or go to www.autopageusa.com .
C3 RS915 REV. O1
20
Compatible
2-Way Communication to the Power of 3
960 Knox Street Unit B, Torrance, CA 90502
Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com
C3 RS915 REV. O1
21