DENON AVR control protocol
Ver.7.6.0
Application model : AVR-3312CI/AVR-3312
Application terminal: RS-232C
Ethernet
Connector specification
Ⅰ. RS-232C
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system
: Tone step synchronization
Communication system
: A half duplex
Communication speed
: 9600bps
Character length
Parity control
Start bit
Stop bit
Communication procedure
Communication data length
Version
7.6.0
Date
Contents
15.Apr.’11
Original
:
:
:
:
:
:
8 bits
None
1 bit
1 bit
Non procedural
135 bytes (maximum)
Page
-1-
Ⅱ. Ethernet
Connector type
: RJ-45(10BASE-T/100BASE-TX)
Example ①
Ethernet
Cross cable
PC
Example ②
AVR
HUB
PC
AVR
Ethernet
Straight
cable
Communication format
Communication
Communication
Communication
Communication
:
system
speed
port
data length
:
:
:
:
Ethernet
Straight
cable
A half duplex
10Mbps/100Mbps
TCP port 23 (telnet)
135bytes (maximum)
-2-
NETWORK SETUP of AVR-3312
>Procedure of Network Setup mode.
(1)Press MENU button, then Menu appears on FL-display(and GUI)
(2)Select “Manual Setup > Network Setup > Network Connecting > Detail” .
(3)Set parameters described below.
<DHCP>
"ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway>
Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy>
Set this parameter "OFF".
<Network Option: Network Standby Mode>
(1)Press MENU button, then Menu appears on FL-display (and GUI)
(2)Select “Manual Setup > Network Setup > Other > Network Standby”
(3)Set parameters described below.
“ON”---Use this setting when using the AVR-3312 Connected in a network.
“OFF”--- Use this setting when not using the AVR-3312 connected in a network.
This setting is reducing the power consumption in the standby mode.
-3-
Protocol specification
The following three data forms are defined.
COMMAND :
The message sent to a system(AVR) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT
:
The message sent to a controller (Touch Panel etc.) from a system (AVR)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE :
The message sent to a controller (Touch Panel etc.) from a system (AVR)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms of receiving the COMMAND.
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs,
AND carriage return (0x0D) --- It is used only as a pause sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters
Ex.
SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex.
DVD : function name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
-4-
The example of a command
* <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSSTEREO<CR> : surround Mode Set to STEREO
MVUP<CR> : Master Volume UP
PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
-5-
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
Ex.
MASTER VOLUME = +1.0dB :
MV81<CR>
+0.5dB :
MV805<CR>
0dB :
MV80<CR>
-0.5dB :
MV795<CR>
-1.0dB :
MV79<CR>
|
|
-79.5dB :
MV005<CR>
-80.0dB :
MV00<CR>
-80.5dB :
MV995<CR>
--:
MV99<CR>
* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.
K) 1 seconds later, please transmit the next COMMAND after transmitting a power on COMMAND(PWON).
-6-
COMMAND and PARAMETER list
COMMAND
PW
PARAMETER
function
example
ON
POWER ON/STANDBY change
PWON<CR>
STANDBY
PWSTANDBY<CR>
?
Return PW Status
PW?<CR>
MV
UP
MASTER VOLUME UP/DOWN , direct change to **dB
MVUP<CR>
DOWN
MVDOWN<CR>
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 995=-80.5dB MV80<CR>
**
?
Return MV Status
MV?<CR>
CV
FL UP
CHANNEL VOLUME UP/DOWN , direct change to **dB
CVFL UP<CR>
FL DOWN
---FRONT Lch
CVFL DOWN<CR>
FL **
**:38 to 62 by ASCII , 50=0dB
CVFL 50<CR>
FR UP
CVFR UP<CR>
FR DOWN
---FRONT Rch
CVFR DOWN<CR>
FR **
**:38 to 62 by ASCII , 50=0dB
CVFR 50<CR>
C UP
CVC UP<CR>
C DOWN
---CENTERch
CVC DOWN<CR>
C **
**:38 to 62 by ASCII , 50=0dB
CVC 50<CR>
SW UP
CVSW UP<CR>
SW DOWN
---SUBWOOFERch
CVSW DOWN<CR>
SW **
**:38 to 62 by ASCII , 50=0dB,00=OFF
CVSW 50<CR>
SL UP
CVSL UP<CR>
SL DOWN
---SURROUND Lch
CVSL DOWN<CR>
SL **
**:38 to 62 by ASCII , 50=0dB
CVSL 50<CR>
SR UP
CVSR UP<CR>
SR DOWN
---SURROUND Rch
CVSR DOWN<CR>
SR **
**:38 to 62 by ASCII , 50=0dB
CVSR 50<CR>
SBL UP
---SURROUND BACK Lch (SBch 2SP)
CVSBL UP<CR>
SBL DOWN
CVSBL DOWN<CR>
SBL **
**:38 to 62 by ASCII , 50=0dB
CVSBL 50<CR>
SBR UP
---SURROUND BACK Rch (SBch 2SP)
CVSBR UP<CR>
SBR DOWN
CVSBR DOWN<CR>
SBR **
**:38 to 62 by ASCII , 50=0dB
CVSBR 50<CR>
MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
-7-
COMMAND
CV
PARAMETER
function
example
SB UP
---SURROUND BACKch
(SBch 1SP)
CVSB UP<CR>
SB DOWN
CVSB DOWN<CR>
SB **
**:38 to 62 by ASCII , 50=0dB
CVSB 50<CR>
FHL UP
CVFHL UP<CR>
FHL DOWN
---FRONT HEIGHT Lch
CVFHL DOWN<CR>
FHL **
**:38 to 62 by ASCII , 50=0dB
CVFHL 50<CR>
FHR UP
CVFHR UP<CR>
FHR DOWN
---FRONT HEIGHT Rch
CVFHR DOWN<CR>
FHR **
**:38 to 62 by ASCII , 50=0dB
CVFHR 50<CR>
FWL UP
CVFWL UP<CR>
FWL DOWN
---FRONT WIDE Lch
CVFWL DOWN<CR>
FWL **
**:38 to 62 by ASCII , 50=0dB
CVFWL 50<CR>
FWR UP
CVFWR UP<CR>
FWR DOWN
---FRONT WIDE Rch
CVFWR DOWN<CR>
FWR **
**:38 to 62 by ASCII , 50=0dB
CVFWR 50<CR>
?
Return CV Status
CV?<CR>
MU
ON
OUTPUT MUTE ON/OFF change
MUON<CR>
OFF
MUOFF<CR>
?
Return MU Status
MU?<CR>
SI
PHONO
Select INPUT source
SIPHONO<CR>
CD
SICD<CR>
TUNER
(Except AVR-3312CI model)
SITUNER<CR>
DVD
SIDVD<CR>
BD
SIBD<CR>
TV
SITV<CR>
SAT/CBL
SISAT/CBL<CR>
DVR
SIDVR<CR>
GAME
SIGAME<CR>
GAME2
SIGAME2<CR>
V.AUX
SIV.AUX<CR>
DOCK
SIDOCK<CR>
HDRADIO
(AVR-3312CI model Only)
SIHDRADIO<CR>
IPOD
Select iPod (dock or USB) and PLAY
SIIPOD<CR>
CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
-8-
COMMAND
SI
ZM
SR
PARAMETER
NET/USB
RHAPSODY
NAPSTER
PANDORA
LASTFM
FLICKR
FAVORITES
IRADIO
SERVER
USB/IPOD
USB
IPD
IRP
FVP
?
ON
OFF
?
PHONO
|
USB/IPOD
SOURCE
?
function
example
SINET/USB<CR>
(North America model Only)
SIRHAPSODY<CR>
(North America & Europe model Only)
SINAPSTER<CR>
(North America model Only)
SIPANDORA<CR>
(Europe model Only)
SILASTFM<CR>
SIFLICKR<CR>
SIFAVORITES<CR>
SIIRADIO<CR>
SISERVER<CR>
Select USB or iPod Direct
SIUSB/IPOD<CR>
Select INPUT source NET/USB and USB Start Playback
SIUSB<CR>
Select INPUT source NET/USB and iPod Direct Start Playback SIIPD<CR>
Select INPUT source NET/USB and Internet Radio Start Playback SIIRP<CR>
Select INPUT source NET/USB and Favorites Start Playback SIFVP<CR>
Return SI Status
SI?<CR>
MAIN ZONE ON/OFF change
ZMON<CR>
ZMOFF<CR>
Return ZM Status
ZM?<CR>
REC SELECT mode set , and select source
SRPHONO<CR>
---The name of PARAMETER is
|
the same as that of the time of SI COMMAND.
SRUSB/IPOD<CR>
REC SELECT mode cancel
SRSOURCE<CR>
Return SR Status
SR?<CR>
-9-
COMMAND
SD
DC
SV
SLP
PARAMETER
AUTO
HDMI
DIGITAL
ANALOG
?
AUTO
PCM
DTS
?
DVD
BD
TV
SAT/CBL
DVR
GAME
GAME2
V.AUX
DOCK
SOURCE
?
OFF
***
?
function
set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG)
set force HDMI INPUT mode
set force DIGITAL INPUT (Optical,Coaxial)mode
set force ANALOG INPUT mode
Return SD Status
set DIGITAL INPUT AUTO mode
set DIGITAL INPUT force PCM mode
set DIGITAL INPUT force DTS mode
Return DC Status
VIDEO SELECT mode set , and select source
VIDEO SELECT mode cancel
Return SV Status
MAIN ZONE SLEEP TIMER setting
***:001 to 120 by ASCII , 010=10min
Return SLP Status
- 10 -
example
SDAUTO<CR>
SDHDMI<CR>
SDDIGITAL<CR>
SDANALOG<CR>
SD?<CR>
DCAUTO<CR>
DCPCM<CR>
DCDTS<CR>
DC?<CR>
SVDVD<CR>
SVBD<CR>
SVTV<CR>
SVSAT/CBL<CR>
SVDVR<CR>
SVGAME<CR>
SVGAME2<CR>
SVV.AUX<CR>
SVDOCK<CR>
SVSOURCE<CR>
SV?<CR>
SLPOFF<CR>
SLP120<CR>
SLP?<CR>
COMMAND
MS
PARAMETER
MOVIE
MUSIC
GAME
DIRECT
PURE DIRECT
STEREO
STANDARD
DOLBY DIGITAL
DTS SUROUND
MCH STEREO
ROCK ARENA
JAZZ CLUB
MONO MOVIE
MATRIX
VIDEO GAME
VIRTUAL
?
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK1 MEMORY
QUICK2 MEMORY
QUICK3 MEMORY
QUICK4 MEMORY
QUICK5 MEMORY
QUICK ?
function
Select SURROUND mode
---5/7CH STEREO mode
Return MS Status
QUICK SELECT 1-5 MODE SELECT
QUICK SELECT 1-5 MODE MEMORY
Return MSQUICK Status
- 11 -
example
MSMOVIE<CR>
MSMUSIC<CR>
MSGAME<CR>
MSDIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSSTANDARD<CR>
MSDOLBY DIGITAL<CR>
MSDTS SURROUND<CR>
MSMCH STEREO<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSMONO MOVIE<CR>
MSMATRIX<CR>
MSVIDEO GAME<CR>
MSVIRTUAL<CR>
MS?<CR>
MSQUICK1<CR>
MSQUICK2<CR>
MSQUICK3<CR>
MSQUICK4<CR>
MSQUICK5<CR>
MSQUICK1 MEMORY<CR>
MSQUICK2 MEMORY<CR>
MSQUICK3 MEMORY<CR>
MSQUICK4 MEMORY<CR>
MSQUICK5 MEMORY<CR>
MSQUICK ?<CR>
COMMAND
VS
PARAMETER
MONIAUTO
MONI1
MONI2
MONI ?
ASPNRM
ASPFUL
ASP ?
SC48P
SC10I
SC72P
SC10P
SC10P24
SCAUTO
SC ?
SCH48P
SCH10I
SCH72P
SCH10P
SCH10P24
SCHAUTO
SCH ?
AUDIO AMP
AUDIO TV
AUDIO ?
VPMAUTO
VPMGAME
VPMMOVI
VPM ?
function
Set HDMI MONITOR automatic detection
Set HDMI MONITOR OUT-1
Set HDMI MONITOR OUT-2
Return VSMONI Status
Set Normal mode
Set FULL mode
Return VSASP Status
Set Resolution to 480p/576p
Set Resolution to 1080i
Set Resolution to 720p
Set Resolution to 1080p
Set Resolution to 1080p:24Hz
Set Resolution to AUTO
Return VSSC Status
Set Resolution to 480p/576p (HDMI)
Set Resolution to 1080i(HDMI)
Set Resolution to 720p(HDMI)
Set Resolution to 1080p(HDMI)
Set Resolution to 1080p:24Hz(HDMI)
Set Resolution to AUTO(HDMI)
Return VSSCH Status(HDMI)
Set HDMI AUDIO Output to AMP
Set HDMI AUDIO Output to TV
Return VSAUDIO Status
Set Video Processing Mode to AUTO
Set Video Processing Mode to GAME
Set Video Processing Mode to MOVIE
Return VSVPM Status
- 12 -
example
VSMONIAUTO<CR>
VSMONI1<CR>
VSMONI2<CR>
VSMONI ?<CR>
VSASPNRM<CR>
VSASPFUL<CR>
VSASP ?<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSC ?<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSCH ?<CR>
VSAUDIO AMP<CR>
VSAUDIO TV<CR>
VSAUDIO ?<CR>
VSVPMAUTO<CR>
VSVPMGAME<CR>
VSVPMMOVI<CR>
VSVPM ?<CR>
COMMAND
PS
PARAMETER
TONE CTRL OFF
TONE CTRL ON
TONE CTRL ?
SB:MTRX ON
SB:PL2x CINEMA
SB:PL2x MUSIC
SB:ON
SB:OFF
SB: ?
CINEMA EQ.ON
CINEMA EQ.OFF
CINEMA EQ. ?
MODE:MUSIC
MODE:CINEMA
MODE:GAME
MODE:PRO LOGIC
MODE: ?
FH:ON
FH:OFF
FH: ?
PHG LOW
PHG MID
PHG HI
PHG ?
SP:FH
SP:FW
SP:SB
SP:OFF
SP: ?
function
PARAMETER setting
TONE CONTROL ON/OFF
Return PSTONE CONTROL Status
SURROUND BACK SP MODE set
Return PSSB: Status
CINEMA EQ. ON/OFF
Return PSCINEMA EQ.Status
CINEMA / MUSIC / GAME / PL mode change
(This parameter can change DOLBY PL2,PL2x,NEO:6 mode.)
---SB=ON:PL2x mode / SB=OFF:PL2 mode
--- GAME can change DOLBY PL2 & PL2x mode
--- PL can change ONLY DOLBY PL2 mode
Return PSMODE: Status
FRONT HEIGHT ON/OFF
Return PSFH: Status
PLⅡz HEIGHT GAIN direct change
Return PSPHG Status
Speaker Output set(F.Height/F.Wide/S.Back)
Return PSSP: Status
- 13 -
example
PSTONE CTRL OFF<CR>
PSTONE CTRL OFF<CR>
PSTONE CTRL ?<CR>
PSSB:MTRX ON<CR>
PSSB:PL2X CINEMA<CR>
PSSB:PL2X MUSIC<CR>
PSSB:ON<CR>
PSSB:OFF<CR>
PSSB: ?<CR>
PSCINEMA EQ.ON<CR>
PSCINEMA EQ.OFF<CR>
PSCINEMA EQ. ?<CR>
PSMODE:MUSIC<CR>
PSMODE:CINEMA<CR>
PSMODE:GAME<CR>
PSMODE:PRO LOGIC<CR>
PSMODE: ?<CR>
PSFH:ON<CR>
PSFH:OFF<CR>
PSFH: ?<CR>
PSPHG LOW<CR>
PSPHG MID<CR>
PSPHG HI<CR>
PSPHG ?<CR>
PSSP:FH<CR>
PSSP:FW<CR>
PSSP:SB<CR>
PSSP:OFF<CR>
PSSP: ?<CR>
COMMAND
PS
PARAMETER
function
MULTEQ:AUDYSSEY
MultEQ XT mode direct change
MULTEQ:BYP.LR
MULTEQ:FLAT
MULTEQ:MANUAL
MULTEQ:OFF
MULTEQ: ?
Return PSMULTEQ: Status
DYNEQ ON
Dynamic EQ = ON
DYNEQ OFF
Dynamic EQ = OFF
DYNEQ ?
Return PSDYNEQ Status
REFLEV 0
Reference Level Offset=0dB
REFLEV 5
Reference Level Offset=5dB
REFLEV 10
Reference Level Offset=10dB
REFLEV 15
Reference Level Offset=15dB
REFREV ?
Return PSREFLEV Status
DYNVOL NGT
Dynamic Volume = Midnight
DYNVOL EVE
Dynamic Volume = Evening
DYNVOL DAY
Dynamic Volume = Day
DYNVOL ?
Return PSDYNVOL Status
DSX ONH
Audyssey DSX ON(Height)
DSX ONW
Audyssey DSX ON(Wide)
DSX OFF
Audyssey DSX OFF
DSX ?
Return PSDSX Status
STW UP
STAGE WIDTH UP/DOWN , direct change to **dB
STW DOWN
**:00 to 99 by ASCII , 50=0dB
STW **
---AVR-3312 can be operated from -10 to +10(40 to 60)
STW ?
Return PSSTW Status
STH UP
STAGE HEIGHT UP/DOWN , direct change to **dB
STH DOWN
**:00 to 99 by ASCII , 50=0dB
STH **
---AVR-3312 can be operated from -10 to +10(40 to 60)
STH ?
Return PSSTH Status
PS COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 14 -
example
PSMULTEQ:AUDYSSEY<CR>
PSMULTEQ:BYP.LR<CR>
PSMULTEQ:FLAT<CR>
PSMULTEQ:MANUAL<CR>
PSMULTEQ:OFF<CR>
PSMULTEQ: ?<CR>
PSDYNEQ ON<CR>
PSDYNEQ OFF<CR>
PSDYNEQ ?<CR>
PSREFLEV 0<CR>
PSREFLEV 5<CR>
PSREFLEV 10<CR>
PSREFLEV 15<CR>
PSREFLEV ?<CR>
PSDYNVOL NGT<CR>
PSDYNVOL EVE<CR>
PSDYNVOL DAY<CR>
PSDYNVOL ?<CR>
PSDSX ONH<CR>
PSDSX ONW<CR>
PSDSX OFF<CR>
PSDSX ?<CR>
PSSTW UP<CR>
PSSTW DOWN<CR>
PSSTW 50<CR>
PSSTW ?<CR>
PSSTH UP<CR>
PSSTH DOWN<CR>
PSSTH 50<CR>
PSSTH ?<CR>
COMMAND
PS
PARAMETER
function
BAS UP
BASS UP/DOWN , direct change to **dB
PSBAS
BAS DOWN
**:00 to 99 by ASCII , 50=0dB
PSBAS
BAS **
---AVR-3312 can be operated from -6 to +6(44 to 56)
PSBAS
BAS ?
Return PSBAS Status
PSBAS
TRE UP
TREBLE UP/DOWN , direct change to **dB
PSTRE
TRE DOWN
**:00 to 99 by ASCII , 50=0dB
PSTRE
TRE **
---AVR-3312 can be operated from -6 to +6(44 to 56)
PSTRE
TRE ?
Return PSTRE Status
PSTRE
DRC AUTO
DRC direct change
PSDRC
DRC LOW
PSDRC
DRC MID
PSDRC
DRC HI
PSDRC
DRC OFF
PSDRC
DRC ?
PSDRC
DCO OFF
D.COMP direct change
PSDCO
DCO LOW
PSDCO
DCO MID
PSDCO
DCO HIGH
PSDCO
DCO ?
Return PSDCO Status
PSDCO
LFE UP
LFE UP/DOWN , direct change to **dB
PSLEE
LFE DOWN
**:00 to 99 by ASCII , 00=0dB, 10=-10dB
PSLFE
LFE **
---AVR-3312 can be operated from 0 to -10
PSLFE
LFE ?
Return PSLFE Status
PSLFE
EFF UP
EFFECT UP/DOWN , EFFECT LEVEL direct change to **dB
PSEFF
EFF DOWN
**:00 to 99 by ASCII , 00=0dB, 10=10dB
PSEFF
EFF **
---AVR-3312 can be operated from 1 to 15
PSEFF
EFF ?
Return PSEFF Status
PSEFF
DEL UP
DELAY UP/DOWN , direct change to ***dB
PSDEL
DEL DOWN
***:000 to 999 by ASCII , 000=0ms, 300=300ms
PSDEL
DEL ***
---AVR-3312 can be operated from 0 to 300
PSDEL
DEL ?
Return PSDEL Status
PSDEL
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 15 -
example
UP<CR>
DOWN<CR>
50<CR>
?<CR>
UP<CR>
DOWN<CR>
50<CR>
?<CR>
AUTO<CR>
LOW<CR>
MID<CR>
HI<CR>
OFF<CR>
?<CR>
OFF<CR>
LOW<CR>
MID<CR>
HIGH<CR>
?<CR>
UP<CR>
DOWN<CR>
10<CR>
? <CR>
UP<CR>
DOWN<CR>
10<CR>
?<CR>
UP<CR>
DOWN<CR>
***<CR>
?<CR>
COMMAND
PS
PARAMETER
function
example
AFD ON
AFDM ON/OFF
PSAFD ON<CR>
AFD OFF
PSAFD OFF<CR>
AFD ?
Return PSAFD Status
PSAFD ?<CR>
PAN ON
PANORAMA ON/OFF
PSPAN ON<CR>
PAN OFF
PSPAN OFF<CR>
PAN ?
Return PSPAN Status
PSPAN ?<CR>
DIM UP
DIMENSION UP/DOWN , direct change to **dB
PSDIM UP<CR>
DIM DOWN
**:00 to 99 by ASCII , 00=0,
PSDIM DOWN<CR>
DIM **
---AVR-3312 can be operated from 0 to 6
PSDIM **<CR>
DIM ?
Return PSDIM Status
PSDIM ?<CR>
CEN UP
CENTER WIDTH UP/DOWN , direct change to **dB
PSCEN UP<CR>
CEN DOWN
**:00 to 99 by ASCII , 00=0
PSCEN DOWN<CR>
CEN **
---AVR-3312 can be operated from 0 to 7
PSCEN 07<CR>
CEN ?
Return PSCEN Status
PSCEN ?<CR>
CEI UP
CENTER IMAGE UP/DOWN , direct change to **dB
PSCEI UP<CR>
CEI DOWN
**:00 to 99 by ASCII , 00=0.0
PSCEI DOWN<CR>
CEI **
---AVR-3312 can be operated from 0.0 to 1.0
PSCEI 10<CR>
CEI?
Return PSCEI Status
OSCEI ?<CR>
SWR ON
SW ON/OFF
PSSWR ON<CR>
SWR OFF
PSSWR OFF<CR>
SWR ?
Return PSSWR Status
PSSWR ?<CR>
RSZ S
ROOM SIZE direct change
PSRSZ S<CR>
RSZ MS
PSRSZ MS<CR>
RSZ M
PSRSZ M<CR>
RSZ ML
PSRSZ ML<CR>
RSZ L
PSRSZ L<CR>
RSZ ?
Return PSRSZ Status
PSRSZ ?<CR>
DELAY UP
AUDIO DELAY UP/DOWN , direct change to ***dB
PSDELAY UP<CR>
DELAY DOWN
***:000 to 999 by ASCII , 000=0ms, 200=200ms
PSDELAY DOWN<CR>
DELAY ***
---AVR-3312 can be operated from 0 to 200
PSDELAY 200<CR>
DELAY ?
Return PSDELAY Status
PSDELAY ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 16 -
COMMAND
PS
PARAMETER
RSTR OFF
RSTR MODE1
RSTR MODE2
RSTR MODE3
RSTR ?
FRONT SPA
FRONT SPB
FRONT SPA+B
FRONT?
function
AUDIO RESTORER direct change
Return PSRSTR Status
FRONT SPEAKER direct change
Return PSFRONT Status
- 17 -
example
PSRSTR OFF<CR>
PSRSTR MODE1<CR>
PSRSTR MODE2<CR>
PSRSTR MODE3<CR>
PSRSTR ?<CR>
PSFRONT SPA<CR>
PSFRONT SPB<CR>
PSFRONT A+B<CR>
PSFRONT?<CR>
COMMAND
PV
PARAMETER
function
CN UP
CONTRAST UP/DOWN , direct change to **dB
CN DOWN
**:44 to 56 by ASCII , 50=0
CN **
---AVR-3312 can be operated from -6 to +6(44 to 56)
CN ?
Return PSCN Status
BR UP
BRIGHTNESS UP/DOWN , direct change to **dB
BR DOWN
**:00 to 12 by ASCII , 00=0
BR **
---AVR-3312 can be operated from 0 to 12
BR ?
Return PSBR Status
CM UP
CHROMA LEVEL UP/DOWN , direct change to **dB
CM DOWN
**:44 to 56 by ASCII , 50=0
CM **
---AVR-3312 can be operated from -6 to +6(44 to 56)
CM ?
Return PSCN Status
HUE UP
HUE UP/DOWN , direct change to **dB
HUE DOWN
**:44 to 56 by ASCII , 50=0
HUE **
---AVR-3312 can be operated from -6 to +6(44 to 56)
HUE ?
Return PSCN Status
DNR OFF
DNR direct change
DNR LOW
DNR MID
DNR HI
DNR ?
Return PVDNR Status
ENH UP
ENHANCER UP/DOWN, direct change to **dB
ENH DOWN
**:00 to 12 by ASCII, 00=0
ENH **
---AVR-3312 can be operated from 0 to 12
ENH ?
Return PVENH Status
PV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 18 -
example
PVCN UP<CR>
PVCN DOWN<CR>
PVCN 50<CR>
PVCN ?<CR>
PVBR UP<CR>
PVBR DOWN<CR>
PVBR 12<CR>
PVBR ?<CR>
PVCM UP<CR>
PVCM DOWN<CR>
PVCM 50<CR>
PVCM ?<CR>
PVHUE UP<CR>
PVHUE DOWN<CR>
PVHUE 50<CR>
PVHUE ?<CR>
PVDNR OFF<CR>
PVDNR LOW<CR>
PVDNR MID<CR>
PVDNR HI<CR>
PVDNR ?<CR>
PVENH UP<CR>
PVENH DOWN<CR>
PVENH 12<CR>
PVENH ?<CR>
COMMAND
Z2
PARAMETER
PHONO
|
USB/IPOD
USB
IPD
IRP
FVP
SOURCE
UP
DOWN
**
ON
OFF
?
Z2MU
ON
OFF
?
Z2CS
ST
MONO
?
Z2CV
FL UP
FL DOWN
FL **
FR UP
FR DOWN
FR **
?
Z2HPF
ON
OFF
?
Z2、Z2CV COMMAND : "*"
function
ZONE2 mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
Select ZONE2 source NET/USB and USB Start Playback
Select ZONE2 source NET/USB and iPod Direct Start Playback
Select ZONE2 source NET/USB and Internet Radio Start Playback
Select ZONE2 source NET/USB and Favorites Start Playback
ZONE2 mode cancel
ZONE2 VOLUME UP/DOWN , direct change to **dB
example
Z2PHONO<CR>
|
Z2USB/IPOD<CR>
Z2USB<CR>
Z2IPD<CR>
Z2IRP<CR>
Z2FVP<CR>
Z2SOURCE<CR>
Z2UP<CR>
Z2DOWN<CR>
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 00=-80dB
Z280<CR>
ZONE2 ON/OFF change
Z2ON<CR>
Z2OFF<CR>
Return Z2 Status
Z2?<CR>
ZONE2 OUTPUT MUTE ON/OFF change
Z2MUON<CR>
Z2MUOFF<CR>
Return Z2MU Status
Z2MU?<CR>
ZONE2 Channel setting
Z2CSST<CR>
Z2CSMONO<CR>
Return Z2CS Status
Z2CS?<CR>
ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB
Z2CVFL UP<CR>
---FRONT Lch
Z2CVFL DOWN<CR>
**:38 to 62 by ASCII , 50=0dB
Z2CVFL 50<CR>
ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB
Z2CVFR UP<CR>
---FRONT Rch
Z2CVFR DOWN<CR>
**:38 to 62 by ASCII , 50=0dB
Z2CVFR 50<CR>
Return Z2CV Status
Z2CV?<CR>
ZONE2 HPF ON/OFF
Z2HPFON<CR>
Z2HPFOFF<CR>
Return Z2HPF Status
Z2HPF?<CR>
parameter uses two ASCII characters. (see page6 J) section)
- 19 -
COMMAND
Z2PS
Z2
PARAMETER
BAS UP
BAS DOWN
BAS **
BAS ?
TRE UP
TRE DOWN
TRE **
TRE ?
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK1 MEMORY
QUICK2 MEMORY
QUICK3 MEMORY
QUICK4 MEMORY
QUICK5 MEMORY
QUICK ?
function
ZONE2 BASS UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
---AVR-3312 can be operated from -10 to +10(40 to 60)
Return Z2PSBAS Status
ZONE2 TREBLE UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
---AVR-3312 can be operated from -10 to +10(40 to 60)
Return Z2PSTRE Status
ZONE2 QUICK SELECT 1-5 MODE SELECT
ZONE2 QUICK SELECT 1-5 MODE MEMORY
Return Z2QUICK Status
Z2PS COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 20 -
example
Z2PSBAS UP<CR>
Z2PSBAS DOWN<CR>
Z2PSBAS 50<CR>
Z2PSBAS ?<CR>
Z2PSTRE UP<CR>
Z2PSTRE DOWN<CR>
Z2PSTRE 50<CR>
Z2PSTRE ?<CR>
Z2QUICK1<CR>
Z2QUICK2<CR>
Z2QUICK3<CR>
Z2QUICK4<CR>
Z2QUICK5<CR>
Z2QUICK1 MEMORY<CR>
Z2QUICK2 MEMORY<CR>
Z2QUICK3 MEMORY<CR>
Z2QUICK4 MEMORY<CR>
Z2QUICK5 MEMORY<CR>
Z2QUICK ?<CR>
COMMAND
Z3
Z3MU
Z3CS
Z3CV
Z3HPF
PARAMETER
PHONO
|
USB/IPOD
USB
IPD
IRP
FVP
SOURCE
UP
DOWN
**
ON
OFF
?
ON
OFF
?
ST
MONO
?
FL UP
FL DOWN
FL **
FR UP
FR DOWN
FR **
?
ON
OFF
?
function
ZONE3 mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
Select ZONE3 source NET/USB and USB Start Playback
Select ZONE3 source NET/USB and iPod Direct Start Playback
Select ZONE3 source NET/USB and Internet Radio Start Playback
Select ZONE3 source NET/USB and Favorites Start Playback
ZONE3 mode cancel
ZONE3 VOLUME UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 00=-80dB
ZONE3 ON/OFF change at AVR-3312
Return Z3 Status
ZONE3 OUTPUT MUTE ON/OFF change
Return Z3MU Status
ZONE3 Channel setting
Return Z3CS Status
ZONE3 CHANNEL VOLUME
---FRONT Lch
**:38 to 62 by ASCII
ZONE3 CHANNEL VOLUME
---FRONT Rch
**:38 to 62 by ASCII
Return Z3CV Status
ZONE3 HPF ON/OFF
UP/DOWN , direct change to **dB
, 50=0dB
UP/DOWN , direct change to **dB
, 50=0dB
Return Z3HPF Status
Z3, Z3CV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 21 -
example
Z3PHONO<CR>
|
Z3USB/IPOD<CR>
Z3USB<CR>
Z3IPD<CR>
Z3IRP<CR>
Z3FVP<CR>
Z3SOURCE<CR>
Z3UP<CR>
Z3DOWN<CR>
Z380<CR>
Z3ON<CR>
Z3OFF<CR>
Z3?<CR>
Z3MUON<CR>
Z3MUOFF<CR>
Z3MU?<CR>
Z3CSST<CR>
Z3CSMONO<CR>
Z3CS?<CR>
Z3CVFL UP<CR>
Z3CVFL DOWN<CR>
Z3CVFL 50<CR>
Z3CVFR UP<CR>
Z3CVFR DOWN<CR>
Z3CVFR 50<CR>
Z3CV?<CR>
Z3HPFON<CR>
Z3HPFOFF<CR>
Z3HPF?<CR>
COMMAND
Z3PS
Z3
PARAMETER
BAS UP
BAS DOWN
BAS **
BAS ?
TRE UP
TRE DOWN
TRE **
TRE ?
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK1 MEMORY
QUICK2 MEMORY
QUICK3 MEMORY
QUICK4 MEMORY
QUICK5 MEMORY
QUICK ?
function
ZONE3 BASS UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
---AVR-3312 can be operated from -10 to +10(40 to 60)
Return Z3PSBAS Status
ZONE3 TREBLE UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
---AVR-3312 can be operated from -10 to +10(40 to 60)
Return Z3PSTRE Status
ZONE3 QUICK SELECT 1-5 MODE SELECT
ZONE3 QUICK SELECT 1-5 MODE MEMORY
Return Z3QUICK Status
Z3PS COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 22 -
example
Z3PSBAS UP<CR>
Z3PSBAS DOWN<CR>
Z3PSBAS 50<CR>
Z3PSBAS ?<CR>
Z3PSTRE UP<CR>
Z3PSTRE DOWN<CR>
Z3PSTRE 50<CR>
Z3PSTRE ?<CR>
Z3QUICK1<CR>
Z3QUICK2<CR>
Z3QUICK3<CR>
Z3QUICK4<CR>
Z3QUICK5<CR>
Z3QUICK1 MEMORY<CR>
Z3QUICK2 MEMORY<CR>
Z3QUICK3 MEMORY<CR>
Z3QUICK4 MEMORY<CR>
Z3QUICK5 MEMORY<CR>
Z3QUICK ?<CR>
ANALOG TUNER Control (except AVR-3312CI model)
COMMAND
TF
TP
TM
PARAMETER
ANUP
ANDOWN
AN******
(6 digits)
AN?
ANUP
ANDOWN
AN**
(PRESET No.)
AN?
ANMEM
ANMEM**
ANAM
ANFM
AN?
ANAUTO
ANMANUAL
function
TUNER Frequency UP/DOWN
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
Return TF Status
TUNER PRESET CH UP/DOWN , direct change to No.**
Return TP Status
TUNER PRESET MEMORY
TUNER PRESET MEMORY, Preset stored at No.**
**:A1-G8
TUNER BAND , MODE Select
---Band set to AM
---Band set to FM
Return TM Status
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
example
TFANUP<CR>
TFANDOWN<CR>
TFAN105000<CR>
(1050.00kHz at AM)
TFAN?<CR>
TPANUP<CR>
TPANDOWN<CR>
TPANA1<CR>
(PRESET No.”A1”)
TPAN?<CR>
TPANMEM<CR>
TPANMEM**<CR>
TMANAM<CR>
TMANFM<CR>
TMAN?<CR>
TMANAUTO<CR>
TMANMANUAL<CR>
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.
- 23 -
HD RADIO Control(AVR-3312CI North America model only)
COMMAND
TF
TP
PARAMETER
HDUP
HDDOWN
HD******
(6 digits)
HDMC*
(1 digit)
HD******MC*
HD?
HDUP
HDDOWN
HD**
(PRESET No.)
HD?
HDMEM
HDMEM**
TM
HDAM
HD
HDFM
HD?
HDAUTOHD
HDAUTO
HDMANUAL
HDANAAUTO
HDANAMANU
HD?
?
function
HD Channel UP/DOWN , direct change
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
---HD Multi Cast CH Select
(*:Multi Cast 1-8)
---Frequency and HD Multi Cast CH Select
Return TFHD Status
HD PRESET CH UP/DOWN , direct change to No.**
Return TPHD Status
HD PRESET MEMORY
HD Radio PRESET MEMORY, Preset stored at No.**
**:A1-G8
HD RADIO BAND , MODE Select
---Band set to AM
---Band set to FM
Return TMHD Status
---Tuning mode set to AUTO-HD mode
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
---Tuning mode set to ANALOG AUTO mode
---Tuning mode set to ANALOG AUTO MANUAL mode
Return TMHD Status
Return HD Status HD?
---BAND, STATION NAME, MULTI CAST CURRENT,
MULTI CAST NUMBER, SIGNAL LEVEL,
ARTIST, TITLE,ALBUM, GENRE, PROGRAM TYPE, MODE
- 24 -
example
TFHDUP<CR>
TFHDDOWN<CR>
TFHD105000<CR>
(1050.00kHz at AM)
TFHDMC2<CR>
TFHD008750MC5<CR>
(87.50kHz at FM)
TFHD?<CR>
TPHDUP<CR>
TPHDDOWN<CR>
TPHDA1<CR>
(PRESET No.”A1”)
TPHD?<CR>
TPHDMEM<CR>
TPHDMEM**<CR>
TMHDAM<CR>
TMHDFM<CR>
TMHD?<CR>
TMHDAUTOHD<CR>
TMHDAUTO<CR>
TMHDMANUAL<CR>
TMHDANAAUTO<CR>
TMHDANAMANU<CR>
TMHD?<CR>
HD?<CR>
※Network Audio/USB /iPod DIRECT Extended Control
COMMAND
NS
PARAMETER
90
91
92
93
94
9A
9B
9C
9D
9E
9H
9I
9J
9K
9M
9W
9X
9Y
PT
NSA
NSE
NSD
*
function
“Cursor Up” Control
“Cursor Down” Control
“Cursor Left” Control
“Cursor Right” Control
“Enter (Play/Pause)” Control
“Play” Control(iRadio/mServer/USB)
“Play/Pause” Control(iPod Direct)
“Pause” Control
“Play/Pause” Control(iPod Direct)
“Stop” Control
“Skip Plus” Control
“Skip Minus” Control
“Repeat One” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Repeat All” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Repeat Off” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Random On/Repeat ALL” (USB/mServer/Rhapsody/Napster)
“Shuffle Songs” Control (iPod Direct Only)
“Random Off” (USB/mServer/Rhapsody/Napster)
“Shuffle Off” Control (iPod Direct Only)
Toggle Switch “Browse Mode/Remote Mode″Control
(iPod Direct Only)
“Page Next” Control
“Page Previous” Control
Enter/Exit PARTY MODE
Return Onscreen Display Information List
(ASCII CODE Character)
Request Onscreen Display Information List
(UTF-8 CODE Character)
“Direct Character Search”(iRadio/mServer/USB/Rhapsody only)
- 25 -
example
NS90<CR>
NS91<CR>
NS92<CR>
NS93<CR>
NS94<CR>
NS9A<CR>
NS9B<CR>
NS9C<CR>
NS9D<CR>
NS9E<CR>
NS9H<CR>
NS9I<CR>
NS9J<CR>
NS9K<CR>
NS9M<CR>
NS9W<CR>
NS9X<CR>
NS9Y<CR>
NSPT<CR>
NSA<CR>
(Return NSA0-NSA8,Refer to Page 46)
NSE<CR>
(Return NSE0-NSE8,Refer to Page 47)
NSD0<CR>
(*:0-9,A-Z)
COMMAND
NS
PARAMETER
P1
P2
P3
P1 MEM
P2 MEM
P3 MEM
P
B**
(PRESET No.)
C**
(PRESET No.)
H
function
Preset1-3 Call
Preset 1-3 Memory
Return Preset 1-3 status(UTF-8)
Preset Call
**:00-55 (00:A1/55:G8)
Preset Memory, Preset stored at No.**
**:00-55 (00:A1/55:G8)
Return Preset Channel A1-G8 status(UTF-8)
- 26 -
example
NSP1<CR>
NSP2<CR>
NSP3<CR>
NSP1 MEM<CR>
NSP2 MEM<CR>
NSP3 MEM<CR>
NSP<CR>
NSB00<CR>
NSC00<CR>
NSH<CR>
※iPod dock Extended Control
※iPod Dock which AVR-3312 can connect with is ASD-1R/11R.
COMMAND
PARAMETER
function
IP
90
“Cursor Up” Control
91
“Cursor Down” Control
92
“Cursor Left” Control
93
“Cursor Right” Control
94
“Enter (Play/Pause)” Control
9A
“Play/Pause” Control
9C
“Stop” Control
9D
“Skip Plus” Control
9E
“Skip Minus” Control
9F
“Manual Search Plus” Control
9G
“Manual Search Minus” Control
9H
“Repeat One” Control
9I
“Repeat All” Control
9J
“Repeat Off” Control
9K
“Shuffle Songs” Control
9L
“Shuffle Album” Control
9M
“Shuffle Off” Control
9N
“MENU” Control
9P
Switch the “Browse Mode” Control
9Q
Switch the “Remote Mode” Control
9X
“Page Next” Control
9Y
“Page Previous” Control
IPA
Return Onscreen Display Information List
(ASCII CODE Character)
IPE
Request Onscreen Display Information List(iPOD)
(UTF-8 CODE Character)
- 27 -
example
IP90<CR>
IP91<CR>
IP92<CR>
IP93<CR>
IP94<CR>
IP9A<CR>
IP9C<CR>
IP9D<CR>
IP9E<CR>
IP9F<CR>
IP9G<CR>
IP9H<CR>
IP9I<CR>
IP9J<CR>
IP9K<CR>
IP9L<CR>
IP9M<CR>
IP9N<CR>
IP9P<CR>
IP9Q<CR>
IP9X<CR>
IP9Y<CR>
IPA<CR>
(Return IPA0-IPA9,Refer to Page 48-49)
IPE<CR>
(Return IPE0-IPE9,Refer to Page 50-51)
※Cursor/Enter/Menu(Setup)
COMMAND
MN
PARAMETER
CUP
CDN
CLT
CRT
ENT
RTN
MEN ON
MEN OFF
SRC ON
SRC OFF
function
“Cursor Up” Control
“Cursor Down” Control
“Cursor Left” Control
“Cursor Right” Control
“Enter” Control
“RETURN” Control
“GUI Menu ON” Control
“GUI Menu OFF” Control
“GUI Source Select Menu ON” Control
“GUI Source Select Menu OFF” Control
example
MNCUP<CR>
MNCDN<CR>
MNCLT<CR>
MNCRT<CR>
MNENT<CR>
MNRTN<CR>
MNMEN ON<CR>
MNMEN OFF<CR>
MNSRC ON<CR>
MNSRC OFF<CR>
※TRIGGER CONTROL
COMMAND
TR
1
1
2
2
PARAMETER
ON
OFF
ON
OFF
function
example
TR1
TR1
TR2
TR2
Trigger 1 ON/OFF Control
Trigger 2 ON/OFF Control
- 28 -
ON<CR>
OFF<CR>
ON<CR>
OFF<CR>
※Remote Lock/Panel Lock
COMMAND
SY
PARAMETER
REMOTE LOCK ON
REMOTE LOCK OFF
PANEL LOCK ON
PANEL+V LOCK ON
PANEL LOCK OFF
function
REMOTE CONTROL LOCK ON/OFF
PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON
PANEL BUTTON & MASTER VOL. CONTROL LOCK ON
PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF
example
SYREMOTE LOCK ON<CR>
SYREMOTE LOCK OFF<CR>
SYPANEL LOCK ON<CR>
SYPANEL+V LOCK ON<CR>
SYPANEL LOCK OFF<CR>
function
ID Number for UPGRADE is displayed on FL Display
UGIDN<CR>
※UPGRADE ID Display
COMMAND
UG
PARAMETER
IDN
- 29 -
example
EVENT(or RESPONSE) and PARAMETER list
EVENT
PW
MV
CV
PARAMETER
ON
STANDBY
**
function
POWER ON/STANDBY change
MASTER VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
00 = -80dB
995 = -80.5dB
99 = ---(MIN)
CHANNEL VOLUME change , **:00,38 to 62 by ASCII
62 = +12dB(MAX)
50 = 0dB
38 = -12dB(MIN)
00 = OFF (define ONLY SWch in DIRECT mode.)
example
PWON<CR>
PWSTANDBY<CR>
MV80<CR>
FL **
CVFL 50<CR>
FR **
CVFR 50<CR>
C **
CVC 50<CR>
SW **
CVSW 50<CR>
SL **
CVSL 50<CR>
SR **
CVSR 50<CR>
SBL **
(at SBch 2SP)
CVSBL 50<CR>
SBR **
(at SBch 2SP)
CVSBR 50<CR>
SB **
(at SBch 1SP)
CVSB 50<CR>
FHL **
CVFHL 50<CR>
FHR **
CVFHR 50<CR>
FWL **
CVFWL 50<CR>
FWR **
CVFWR 50<CR>
MU
ON
OUTPUT MUTE ON/OFF change
MUON<CR>
OFF
MUOFF<CR>
SI
PHONO
INPUT source change
SIPHONO<CR>
CD
SICD<CR>
TUNER
(Except AVR-3312CI model)
SITUNER<CR>
DVD
SIDVD<CR>
BD
SIBD<CR>
TV
SITV<CR>
SAT/CBL
SISAT/CBL<CR>
DVR
SIDVR<CR>
GAME
SIGAME<CR>
The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page6 J) section)
- 30 -
EVENT
SI
ZM
SR
PARAMETER
GAME2
V.AUX
DOCK
HDRADIO
IPOD
NET/USB
RHAPSODY
NAPSTER
PANDORA
LASTFM
FLICKR
FAVORITES
IRADIO
SERVER
USB DIRECT
IPOD DIRECT
USB
IPD
IRP
FVP
ON
OFF
PHONO
|
IPOD DIRECT
SOURCE
function
(North America model Only)
(North America model Only)
(North America & Europe model Only)
(North America model Only)
(Europe model Only)
MAIN ZONE ON/OFF change
REC SELECT source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
REC SELECT mode cancel
- 31 -
example
SIGAME2<CR>
SIV.AUX<CR>
SIDOCK<CR>
SIHDRADIO<CR>
SIIPOD<CR>
SINET/USB
SIRHAPSODY<CR>
SINAPSTER<CR>
SIPANDORA<CR>
SILASTFM<CR>
SIFLICKR<CR>
SIFAVORITES<CR>
SIIRADIO<CR>
SISERVER<CR>
SIUSB DIRECT<CR>
SIIPOD DIRECT<CR>
SIUSB<CR>
SIIPD<CR>
SIIRP<CR>
SIFVP<CR>
ZMON<CR>
ZMOFF<CR>
SRPHONO<CR>
SRSOURCE<CR>
EVENT
SD
DC
SV
SLP
PARAMETER
AUTO
HDMI
DIGITAL
ANALOG
ARC
NO
AUTO
PCM
DTS
DVD
BD
TV
SAT/CBL
DVR
GAME
GAME2
V.AUX
DOCK
SOURCE
OFF
***
function
INPUT mode change
ARC playing
No Input
DIGITAL INPUT mode change
VIDEO SELECT mode source change
MAIN ZONE SLEEP TIMER setting change
- 32 -
example
SDAUTO<CR>
SDHDMI<CR>
SDDIGITAL<CR>
SDANALOG<CR>
SDARC<CR>
SDNO<CR>
DCAUTO<CR>
DCPCM<CR>
DCDTS<CR>
SVDVD<CR>
SVBD<CR>
SVTV<CR>
SVSAT/CBL<CR>
SVDVR<CR>
SVGAME<CR>
SVGAME2<CR>
SVV.AUX<CR>
SVDOCKCR>
SVSOURCE<CR>
SLPOFF<CR>
SLP120<CR>
EVENT
MS
PARAMETER
DIRECT
PURE DIRECT
STEREO
MULTI CH IN
M CH IN+PL2X C
M CH IN+PL2X M
M CH IN+PL2Z H
M CH IN
+DOLBY EX
MULTI CH IN 7.1
DOLBY PRO LOGIC
DOLBY PL2 C
DOLBY PL2 M
DOLBY PL2 G
DOLBY PL2X C
DOLBY PL2X M
DOLBY PL2X G
DOLBY PL2Z H
DOLBY DIGITAL
DOLBY D EX
DOLBY D
+PL2X C
DOLBY D
+PL2X M
DOLBY D
+PL2Z H
DTS NEO:6 C
DTS NEO:6 M
DTS SURROUND
DTS ES DSCRT6.1
DTS ES MTRX6.1
DTS+PL2X C
DTS+PL2X M
DTS+PL2Z H
function
SURROUND mode change
example
MSDIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSMULTI CH IN<CR>
MSM CH IN+PL2X C<CR>
MSM CH IN+PL2X M<CR>
MSM CH IN+PL2Z H<CR>
MSM CH IN+DOLBY EX<CR>
MSMULTI
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
CH IN 7.1<CR>
PRO LOGIC<CR>
PL2 C<CR>
PL2 M<CR>
PL2 G<CR>
PL2X C<CR>
PL2X M<CR>
PL2X G<CR>
PL2Z H<CR>
DIGITAL<CR>
D EX<CR>
D+PL2X C<CR>
MSDOLBY D+PL2X M<CR>
MSDOLBY D+PL2Z H<CR>
MSDTS NEO:6 C<CR>
MSDTS NEO:6 M<CR>
MSDTS SURROUND<CR>
MSDTS ES DSCRT6.1<CR>
MSDTS ES MTRX6.1<CR>
MSDTS+PL2X C<CR>
MSDTS+PL2X M<CR>
MSDTS+PL2Z H<CR>
- 33 -
EVENT
PARAMETER
DTS+NEO:6
DTS96/24
DTS96 ES MTRX
MCH STEREO
ROCK ARENA
JAZZ CLUB
MONO MOVIE
MATRIX
VIDEO GAME
VIRTUAL
DOLBY D+
DOLBY D+ +EX
DOLBY D+ +PL2X C
DOLBY D+ +PL2X M
DOLBY D+ +PL2Z H
DOLBY TRUEHD
DOLBY HD
DOLBY HD+EX
DOLBY HD+PL2X C
DOLBY HD+PL2X M
DOLBY HD+PL2Z H
DTS HD
DTS HD MSTR
DTS HD+NEO:6
DTS HD+PL2X C
DTS HD+PL2X M
DTS HD+PL2Z H
DTS ES 8CH DSCRT
DTS EXPRESS
MPEG2 AAC
AAC+DOLBY EX
AAC+PL2X C
AAC+PL2X M
AAC+PL2Z H
function
---5/7CH STEREO mode
(JAPAN
(JAPAN
(JAPAN
(JAPAN
(JAPAN
model
model
model
model
model
Only)
Only)
Only)
Only)
Only)
- 34 -
example
MSDTS+NEO:6<CR>
MSDTS96/24<CR>
MSDTS96 ES MTRX<CR>
MSMCH STEREO<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSMONO MOVIE<CR>
MSMATRIX<CR>
MSVIDEO GAME<CR>
MSVIRTUAL<CR>
MSDOLBY D+<CR>
MSDOLBY D+ +EX<CR>
MSDOLBY D+ +PL2X C<CR>
MSDOLBY D+ +PL2X M<CR>
MSDOLBY D+ +PL2Z H<CR>
MSDOLBY HD<CR>
MSDOLBY HD<CR>
MSDOLBY HD+EX<CR>
MSDOLBY HD+PL2X C<CR>
MSDOLBY HD+PL2X M<CR>
MSDOLBY HD+PL2Z H<CR>
MSDTS HD<CR>
MSDTS HD MSTR<CR>
MSDTS HD+NEO:6<CR>
MSDTS HD+PL2X C<CR>
MSDTS HD+PL2X M<CR>
MSDTS HD+PL2Z H<CR>
MSDTS ES 8CH DSCRT<CR>
MSDTS EXPRESS<CR>
MSMPEG2 AAC<CR>
MSAAC+DOLBY EX<CR>
MSAAC+PL2X C<CR>
MSAAC+PL2X M<CR
MSAAC+PL2Z H<CR>
EVENT
MS
PARAMETER
AUDYSSEY DSX
PL DSX
PL2 C DSX
PL2 M DSX
PL2 G DSX
NEO:6 C DSX
NEO:6 M DSX
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
function
QUICK SELECT mode change
---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF
- 35 -
example
MSAUDYSSEY DSX<CR>
MSPL DSX<CR>
MSPL2 C DSX<CR>
MSPL2 M DSX<CR>
MSPL2 G DSX<CR>
MSNEO:6 C DSX<CR>
MSNEO:6 M DSX<CR>
MSQUICK1<CR>
MSQUICK2<CR>
MSQUICK3<CR>
MSQUICK4<CR>
MSQUICK5<CR>
MSQUICK0<CR>
EVENT
VS
PARAMETER
MONIAUTO
MONI1
MONI2
ASPNRM
ASPFUL
SC48P
SC10I
SC72P
SC10P
SC10P24
SCAUTO
SCH48P
SCH10I
SCH72P
SCH10P
SCH10P24
SCHAUTO
AUDIO AMP
AUDIO TV
VPMAUTO
VPMGAME
VPMMOVI
function
HDMI MONITOR setting change
ASPECT setting change
Resolution(analog) setting change
Resolution(HDMI) setting change
HDMI AUDIO Output setting change
Video Mode setting change
- 36 -
example
VS MONIAUTOCR>
VSMONI1<CR>
VSMONI2<CR>
VSASPNRM<CR>
VSASPFUL<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSCH48P<CR>
VSSCH10I<CR>
VSSCH72P<CR>
VSSCH10P<CR>
VSSCH10P24<CR>
VSSCHAUTO<CR>
VSAUDIO AMP<CR>
VSAUDIO TV<CR>
VSVPMAUTO<CR>
VSVPMGAME<CR>
VSVPMMOVI<CR>
EVENT
PS
PARAMETER
TONE CTRL OFF
TONE CTRL ON
SB:MTRX ON
SB:PL2X CINEMA
SB:PL2X MUSIC
SB:ON
SB:OFF
SB:ESMTRX
CINEMA EQ.ON
CINEMA EQ.OFF
MODE:CINEMA
MODE:MUSIC
MODE:GAME
MODE:PRO LOGIC
MODE:HEIGHT
FH:ON
FH:OFF
PHG LOW
PHG MID
PHG HI
SP:FH
SP:FW
SP:SB
SP:OFF
MULTEQ:AUDYSSEY
MULTEQ:BYP.LR
MULTEQ:FLAT
MULTEQ:MANUAL
MULTEQ:OFF
DYNEQ ON
DYNEQ OFF
function
TONE CONTROL ON/OFF change
SURROUND BACK MODE change
CINEMA EQ. ON/OFF change
CINEMA / MUSIC / GAME / PL /HEIGHT mode change
FRONT HEIGHT Output change
PLⅡz HEIGHT GAIN direct change
Speaker Output set(F.Height/F.Wide/S.Back)
MultEQ XT mode change
DYNAMIC EQ change
- 37 -
example
PSTONE CTRL OFF<CR>
PSTONE CTRL OFF<CR>
PSSB:MTRX ON<CR>
PSSB:PL2X CINEMA<CR>
PSSB:PL2X MUSIC<CR>
PSSB:ON<CR>
PSSB:OFF<CR>
PSSB:ESMTRX<CR>
PSCINEMA EQ.ON<CR>
PSCINEMA EQ.OFF<CR>
PSMODE:CINEMA<CR>
PSMODE:MUSIC<CR>
PSMODE:GAME<CR>
PSMODE:PRO LOGIC<CR>
PSMODE:HEIGHT<CR>
PSFH:ON<CR>
PSFH:OFF<CR>
PSPHG LOW<CR>
PSPHG MID<CR>
PSPHG HI<CR>
PSSP:FH<CR>
PSSP:FW<CR>
PSSP:SB<CR>
PSSP:OFF<CR>
PSMULTEQ:AUDYSSEY<CR>
PSMULTEQ:BYP.LR<CR>
PSMULTEQ:FLAT<CR>
PSMULTEQ:MANUAL<CR>
PSMULTEQ:OFF<CR>
PSDYNEQ ON<CR>
PSDYNEQ OFF<CR>
EVENT
PS
PARAMETER
REFLEV 0
REFLEV 5
REFLEV 10
REFLEV 15
DYNVOL NGT
DYNVOL EVE
DYNVOL DAY
DSX ONH
DSX ONW
DSX OFF
STW **
STH **
BAS **
TRE **
DRC AUTO
DRC LOW
DRC MID
DRC HI
DRC OFF
DCO OFF
DCO LOW
DCO MID
DCO HIGH
LFE **
EFF **
DEL ***
function
Reference Level Offset change
DYNAMIC VOLUME change
Audyssey DSX change
STAGE WIDTH change
STAGE HEIGHT change
BASS change
TREBLE change
DRC change
D.COMP change
LFE change
EFFECT LEVEL change
DELAY change
- 38 -
example
PSREFLEV 0<CR>
PSREFLEV 5<CR>
PSREFLEV 10<CR>
PSREFLEV 15<CR>
PSDYNVOL NGT<CR>
PSDYNVOL EVE<CR>
PSDYNVOL DAY<CR>
PSDSX ON<CR>
PSDSX ON<CR>
PSDSX OFF<CR>
PSSTW 50<CR>
PSSTH 50<CR>
PSBAS 50<CR>
PSTRE 50<CR>
PSDRC AUTO<CR>
PSDRC LOW<CR>
PSDRC MID<CR>
PSDRC HI<CR>
PSDRC OFF<CR>
PSDCO OFF<CR>
PSDCO LOW<CR>
PSDCO MID<CR>
PSDCO HIGH<CR>
PSLFE 10<CR>
PSEFF 10<CR>
PSDEL 100<CR>
EVENT
PS
PARAMETER
AFD ON
AFD OFF
PAN ON
PAN OFF
DIM **
CEN **
CEI **
SWR ON
SWR OFF
RSZ S
RSZ MS
RSZ M
RSZ ML
RSZ L
DELAY ***
RSTR OFF
RSTR MODE1
RSTR MODE2
RSTR MODE3
FRONT SPA
FRONT SPB
FRONT SPA+B
function
AFDM change
PANORAMA change
DIMMENSION change
CENTER WIDTH change
CENTER IMAGE change
SW ON/OFF change
ROOM SIZE change
AUDIO DELAY change
AUDIO RESTORER change
FRONT SPEAKER direct change
- 39 -
example
PSAFD ON<CR>
PSAFD OFF<CR>
PSPAN ON<CR>
PSPAN OFF<CR>
PSDIM 06<CR>
PSCEN 07<CR>
PSCEI 10<CR>
PSSWR ON<CR>
PSSWR OFF<CR>
PSRSZ S<CR>
PSRSZ MS<CR>
PSRSZ M<CR>
PSRSZ ML<CR>
PSRSZ L<CR>
PSDELAY 200<CR>
PSRSTR OFF<CR>
PSRSTR MODE1<CR>
PSRSTR MODE2<CR>
PSRSTR MODE3<CR>
PSFRONT SPA<CR>
PSFRONT SPB<CR>
PSFRONT A+B<CR>
EVENT
PV
PARAMETER
CN **
BR **
CM **
HUE **
DNR OFF
DNR LOW
DNR MID
DNR HI
ENH **
function
CONTRAST change
BRIGHTNESS Change
CROMA LEVEL change
Hue Change
DNR change
ENHANCER change
- 40 -
example
PVCN 50<CR>
PVBR 12<CR>
PVCM 50<CR>
PVHUE 50<CR>
PVDNR OFF<CR>
PVDNR LOW<CR>
PVDNR MID<CR>
PVDNR HI<CR>
PVENH 12<CR>
EVENT
Z2
PARAMETER
PHONO
|
USB DIRECT
IPOD DIRECT
SOURCE
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
**
Z2MU
Z2CS
Z2CV
Z2HPF
Z2PS
function
ZONE2 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
ZONE2 mode cancel
ZONE2 QUICK SELECT mode change
---Z2 QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF
ZONE2 VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
10 = -70dB
00 = -80dB
99 = ---(MIN)
ZONE2 ON/OFF change
example
Z2PHONO<CR>
|
Z2USB DIRECT<CR>
Z2IPOD DIRECT<CR>
Z2SOURCE<CR>
Z2QUICK1<CR>
Z2QUICK2<CR>
Z2QUICK3<CR>
Z2QUICK4<CR>
Z2QUICK5<CR>
Z2QUICK0<CR>
Z280<CR>
ON
OFF
ON
OFF
ST
MONO
FL **
FR **
ON
OFF
BAS **
ZONE2 BASS change
Z2ON<CR>
Z2OFF<CR>
Z2MUON<CR>
Z2MUOFF<CR>
Z2CSST<CR>
Z2CSMONO<CR>
Z2CVFL 50<CR>
Z2CVFR 50<CR>
Z2HPFON<CR>
Z2HPFOFF<CR>
Z2PSBAS 50<CR>
TRE **
ZONE2 TEBLE change
Z2PSTRE 50<CR>
ZONE2 OUTPUT MUTE ON/OFF change
ZONE2 Channel setting
**:38 to 62 by ASCII , 50=0dB
**:38 to 62 by ASCII , 50=0dB
ZONE2 HPF ON/OFF change
The PARAMETER of Z2 EVENT : Uses two ASCII characters. (see page4 J) section)
- 41 -
EVENT
Z3
PARAMETER
PHONO
|
USB DIRECT
IPOD DIRECT
SOURCE
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
**
function
ZONE3 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
ZONE3 mode cancel
ZONE3 QUICK SELECT mode change
---Z3 QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF
ZONE3 VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
10 = -70dB
00 = -80dB
99 = ---(MIN)
ZONE3 ON/OFF change
ON
OFF
Z3MU
ON
ZONE3 OUTPUT MUTE ON/OFF change
OFF
Z3CS
ST
ZONE3 Channel setting
MONO
Z3CV
FL **
**:38 to 62 by ASCII , 50=0dB
FR **
**:38 to 62 by ASCII , 50=0dB
Z3HPF
ON
ZONE3 HPF ON/OFF change
OFF
Z3PS
BAS **
ZONE3 BASS change
TRE **
ZONE3 TEBLE change
The PARAMETER of Z3 EVENT : Uses two ASCII characters. (see page4 J) section)
- 42 -
example
Z3PHONO<CR>
|
Z3USB DIRECT<CR>
Z3IPOD DIRECT<CR>
Z3SOURCE<CR>
Z3QUICK1<CR>
Z3QUICK2<CR>
Z3QUICK3<CR>
Z3QUICK4<CR>
Z3QUICK5<CR>
Z3QUICK0<CR>
Z380<CR>
Z3ON<CR>
Z3OFF<CR>
Z3MUON<CR>
Z3MUOFF<CR>
Z3CSST<CR>
Z3CSMONO<CR>
Z3CVFL 50<CR>
Z3CVFR 50<CR>
Z3HPFON<CR>
Z3HPFOFF<CR>
Z3PSBAS 50<CR>
Z3PSTRE 50<CR>
※ANALOG TUNER Control(except AVR-3312CI North America model)
EVENT
TF
PARAMETER
AN******
(6 digits)
TP
AN**(PRESET No.)
TM
ANOFF
ANMEM**
ANAM
ANFM
ANAUTO
ANMANUAL
function
TUNER Frequency change
--- ****.** kHz at AM band
****.** MHz at FM band
TUNER PRESET change to No.**
Change Preset Channel select OFF
TUNER PRESET MEMORY
TUNER BAND , MODE change
---Band set to AM
---Band set to FM
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
- 43 -
example
TFAN105000<CR>
(1050.00kHz at AM)
TPANA1<CR>
(PRESET No.”A1”)
TPANOFF<CR>
TPANMEMA1<CR>
TMANAM<CR>
TMANFM<CR>
TMANAUTO<CR>
TMANMANUAL<CR>
※HD RADIO Control(AVR-3312CI North America model only)
EVENT
TF
PARAMETER
HD******
(6 digits)
HDMC*(1 digit)
TP
HD**(PRESET No.)
function
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
---HD Multi Cast CH change
(*:Multi Cast 1-8, Analog 0)
HD RADIO PRESET change to No.**
HDOFF
HDMEM**
TM
HD
Change Preset Channel select OFF
HDRADIO PRESET MEMORY
HD RADIO BAND , MODE change
HDAM
---Band set to AM
HDFM
---Band set to FM
HDAUTOHD
---Tuning mode set to AUTO-HD mode
HDAUTO
---Tuning mode set to AUTO mode
HDMANUAL
---Tuning mode set to MANUAL mode
HDANAAUTO
---Tuning mode set to ANALOG AUTO mode
HDANAMANU
---Tuning mode set to ANALOG AUTO MANUAL mode
ST NAME(8 digits) HD STATION NAME change
STL NAME
HD STATION LONG NAME change
(56 digits)
SIG LEV *
HD ANTENNA SIGNAL STATUS change
(1 digit)
MLT CURRCH *
(1 digit)
MLT CAST CH
(1 digits)
example
TPHD105000<CR>
(1050.00kHz at AM)
TFHDMC2<CR>
TPHDA1<CR>
(PRESET No.”A1”)
TPHDOFF<CR>
TPHDMA1<CR>
TMHDAM<CR>
TMHDFM<CR>
TMHDAUTOHD<CR>
TMHDAUTO<CR>
TMHDMANUAL<CR>
TMHDANAAUTO<CR>
TMHDANAMANU<CR>
HDST NAME ********<CR>
HDSTL NAME (56 digits)<CR>
HD MULTI CAST CURRENT CH change
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDMLT
HD MULTI CAST CH NUMBER
HDMLT CAST CH *<CR>
- 44 -
LEV 0<CR>
LEV 1<CR>
LEV 2<CR>
LEV 3<CR>
LEV 4<CR>
LEV 5<CR>
LEV 6<CR>
CURRCH *<CR>
EVENT
HD
PARAMETER
PTY(18 digits)
ARTIST(40 digits)
TITLE(40 digits)
ALBUM(40 digits)
GENRE(23 digits)
MODE
HD
HD
HD
HD
HD
HD
function
PROGRAM TYPE change
ARTIST NAME change
TITLE NAME change
ALBUM NAME change
GANRE change
MODE(ANALOG/DIGITAL)
- 45 -
example
HDPTY (18 digits)<CR>
HDARTIST (40 digits)<CR>
HDTITLE (40 digits)<CR>
HDALBUM (40 digits)<CR>
HDGENRE (23 digits)<CR>
HDMODE DIGITAL<CR>
HDMODE ANALOG<CR>
※Network Audio/USB /iPod DIRECT Extended Control
EVENT
PARAMETER
NSA
0
1
2
3
4
5
6
7
8
function
Onscreen Display Information is Answered
By the NSA Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
- 46 -
example
NSA0**************_?????<CR>
NSA1※************_?????<CR>
NSA2※************_?????<CR>
NSA3※************_?????<CR>
NSA4※************_?????<CR>
NSA5※************_?????<CR>
NSA6※************_?????<CR>
NSA7**************_?????<CR>
NSA8**************_?????<CR>
*:Character Length MAX96byte
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor&Playable
Information Data(1Byte)
Bit1:Playable Music
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit3,5,6,8:Don't Care
NSA0Now Playing USB_????<CR>
NSA1※Come Away With Me_???<CR>
NSA2※Norah Jones_?????????<CR>
NSA3※_????????????????????<CR>
NSA4※_????????????????????<CR>
NSA5※00:11
100%_???????<CR>
NSA6※_????????????????????<CR>
NSA7_????????????????????<CR>
NSA8_????????????????????<CR>
EVENT
PARAMETER
NSE
0
1
2
3
4
5
6
7
8
function
Onscreen Display Information(mServer/iRadio) is
Answered By the NSE Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
- 47 -
example
NSE0**************_?????<CR>
NSE1※************_?????<CR>
NSE2※************_?????<CR>
NSE3※************_?????<CR>
NSE4※************_?????<CR>
NSE5※************_?????<CR>
NSE6※************_?????<CR>
NSE7**************_?????<CR>
NSE8**************_?????<CR>
*:UTF-8 CODE Character(MAX96byte)
_:Null
?: Don't Care (The character after Null
should be disregarded)
※:Cursor&Playable
Information Data(1Byte)
Bit1:Playable Music =1
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit3,5,6,8:Don't Care
************_?????:96byte Fixed
<example>
NSE0Now Playing USB_????<CR>
NSE1※Come Away With Me_???<CR>
NSE2※Norah Jones_?????????<CR>
NSE3※_????????????????????<CR>
NSE4※_????????????????????<CR>
NSE5※00:11
100%_???????<CR>
NSE6※_????????????????????<CR>
NSE7_????????????????????<CR>
NSE8_????????????????????<CR>
COMMAND
NS
PARAMETER
P1
P2
P3
P1 MEM
P2 MEM
P3 MEM
P
B**
(PRESET No.)
C**
(PRESET No.)
H
function
Preset1-3 Call
Preset 1-3 Memory
Return Preset 1-3 status(UTF-8)
Preset Call
**:00-55 (00:A1/55:G8)
Preset Memory, Preset stored at No.**
**:00-55 (00:A1/55:G8)
Return Preset Channel A1-G8 status(UTF-8)
(00:A1-55:G8)
- 48 -
example
NSP1<CR>
NSP2<CR>
NSP3<CR>
NSP1 MEM<CR>
NSP2 MEM<CR>
NSP3 MEM<CR>
NSP01**********(20 digits)<CR>
NSP02**********(20 digits)<CR>
NSP03**********(20 digits)<CR>
***:Station name or Title name
NSB00<CR>
NSC00<CR>
NSH00**********(20
NSH01**********(20
|
NSH54**********(20
NSH55**********(20
digits)<CR>
digits)<CR>
digits)<CR>
digits)<CR>
※iPod Extended Control
iPod Dock which AVR-3312 can connect with is ASD-1R/11R.
EVENT
PARAMETER
function
IPA
Onscreen Display Information is Answered
By the IPA Command.
0
Display Line1 Information
1
Display Line3 Information
2
Display Line4 Information
3
Display Line5 Information
4
Display Line6 Information
5
Display Line7 Information
6
Display Line8 Information
7
Display Line9 Information
8
Display Line10 Information
9
Display Line11 Information
example
IPA0***************_???<CR>
IPA1※*************_???<CR>
IPA2※*************_???<CR>
IPA3※*************_???<CR>
IPA4※*************_???<CR>
IPA5※*************_???<CR>
IPA6※*************_???<CR>
IPA7※*************_???<CR>
IPA8#**************_???<CR>
IPA9***************_???<CR>
*:Character Length MAX96byte
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit4:CURSOR SELECT=1
Bit3,5,6,7,8:Don't Care
#:Bit1-8:Don’t Care
- 49 -
EVENT
PARAMETER
function
IPA
example
<example1>
IPA0Artist??????????????????<CR>
IPA1※ Ana Caram_????????????<CR>
IPA2※ Badi Assad_???????????<CR>
IPA3※ Christy Baron_????????<CR>
IPA4※ Marta Gomez_??????????<CR>
IPA5※ Rebecca Pidgeon_??????<CR>
IPA6※ Sara K_???????????????<CR>
IPA7※ Valerie Joyce_????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9 [
2/
6]_?????????<CR>
<example2>
IPA0Now Playing iPod_???????<CR>
IPA1※ A HARD DAY'S NIGHT._??<CR>
IPA2※ /The Beatles_?????????<CR>
IPA3※_??????????????????????<CR>
IPA4※ A HARD DAY'S NIGHT_???<CR>
IPA5※ 00:04_??????????????<CR>
IPA6※_??????????????????????<CR>
IPA7※_??????????????????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9????????????????????????<CR>
- 50 -
EVENT
PARAMETER
IPE
0
1
2
3
4
5
6
7
8
9
function
Onscreen Display Information(iPod) is Answered
By the IPA Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
Display Line11 Information
example
IPE0***************_???<CR>
IPE1※*************_???<CR>
IPE2※*************_???<CR>
IPE3※*************_???<CR>
IPE4※*************_???<CR>
IPE5※*************_???<CR>
IPE6※*************_???<CR>
IPE7※*************_???<CR>
IPE8#**************_???<CR>
IPE9***************_???<CR>
*:UTF-8 CODE Character(MAX96byte)
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit3:Don't Care
Bit4:CURSOR SELECT=1
Bit3,5,6,7,8:Don't Care
#:Bit1-8:Don’t Care
- 51 -
EVENT
PARAMETER
function
IPE
example
<example1>
IPE0Artist??????????????????<CR>
IPE1※ Ana Caram_????????????<CR>
IPE2※ Badi Assad_???????????<CR>
IPE3※ Christy Baron_????????<CR>
IPE4※ Marta Gomez_??????????<CR>
IPE5※ Rebecca Pidgeon_??????<CR>
IPE6※ Sara K_???????????????<CR>
IPE7※ Valerie Joyce_????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9 [
2/
6]_?????????<CR>
<example2>
IPE0Now Playing iPod_???????<CR>
IPE1※ A HARD DAY'S NIGHT._??<CR>
IPE2※ /The Beatles_?????????<CR>
IPE3※_??????????????????????<CR>
IPE4※ A HARD DAY'S NIGHT_???<CR>
IPE5※ 00:04_??????????????<CR>
IPE6※_??????????????????????<CR>
IPE7※_??????????????????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9_??????????????????????<CR>
- 52 -
※TRIGGER CONTROL
EVENT
TR
1
1
2
2
PARAMETER
ON
OFF
ON
OFF
function
Trigger
Trigger
Trigger
Trigger
1
1
2
2
example
TR1
TR1
TR2
TR2
ON
OFF
ON
OFF
ON<CR>
OFF<CR>
ON<CR>
OFF<CR>
※Remote Lock/Panel Lock
EVENT
SY
PARAMETER
REMOTE LOCK ON
REMOTE LOCK OFF
PANEL LOCK ON
PANEL+V LOCK ON
PANEL LOCK OFF
function
REMOTE CONTROL LOCK ON/OFF
PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON
PANEL BUTTON & MASTER VOL. CONTROL LOCK ON
PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF
example
SYREMOTE LOCK ON<CR>
SYREMOTE LOCK OFF<CR>
SYPANEL LOCK ON<CR>
SYPANEL+V LOCK ON<CR>
SYPANEL LOCK OFF<CR>
※UPGRADE ID Display
COMMAND
UG
PARAMETER
IDN ************
IDN NG
function
ID Number for UPGRADE is displayed on FL Display
************:12-digit ID Number
Can’t get ID number from DPMS
- 53 -
example
UGIDN ************<CR>
UGIDN NG<CR>
Extension COMMAND
・The RC code can be sent from Serial protocol commands
Protocol specification
Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D)
COMMAND : ASCII CODE of 2 characters
Ex.
RC : RC CODE
RC FORMAT : ASCII CODE of 3 characters
Ex.
KSK : KASEIKYO FORMAT
SHP : SHARP FORMAT
RC DATA : ASCII CODE of 7 characters
※For details of the RC CODE , please refer to the IR remote control code list.
KASEIKYO FORMAT
SHARP FORMAT
- 54 -
The example of a command
* <CR> is the meaning of 0x0D.
RCKSK0410002<CR> : All Power ON by using KASEIKYO FORMAT
RCSHP0230033<CR> : All Power ON by using SHARP FORMAT
- 55 -