COLUMBIA
®
Cast Iron Gas-Fired Steam Boilers
CEG-C SERIES
KEEPING FAMILIES
★ ★ ★ ★★
★ ★★★
★ ★ ★ ★★
★ ★★★
★ ★ ★ ★★
★ ★★★
★ ★ ★ ★★
WARM SINCE 1936
Quality Engineered for Efficiency and Dependability
CEG-C SERIES
Gas-Fired /Steam
Meeting The Comfort Demands
Of A Steam Heated Home
Quality Cast Iron
Construction
The CEG-C utilizes cast iron
construction because of its
durability and efficient heat transfer
capabilities. Cast iron sections and
push nipples are an integral part of
each CEG-C heat exchanger. Using
only the highest quality cast iron
and heat transfer designs, the
CEG-C will provide many years of
efficient and trouble-free operation.
Fuel Saving Components
Advanced engineering can be found in every part of a
CEG-C boiler. An optional "on-demand" ignition control
eliminates wasted fuel associated with a continuously
burning pilot light.
In addition, an
integrated automatic
vent damper closes
when the burner
shuts off, preventing
heat from leaving
through the chimney
saving fuel and
heating costs.
Low Profile Design
The CEG-C boiler is compactly designed with a low profile
draft hood allowing installation in areas with low ceilings.
High Energy Efficiency
and Lower Heating Costs
With efficiency ratings as high as 82%, the CEG-C provides
increased energy savings resulting in lower fuel bills. With
the potential cost savings this represents, the CEG-C boiler
can pay for itself in a few short years.
Compare The Difference
High Efficiency Makes
$900
Annual Fuel Costs
The CEG-C boiler represents the finest in steam boiler
construction and cost saving technologies. Available in six
sizes with efficiencies up to 82%, the CEG-C is the ideal
replacement or upgrade for homeowners interested in
comfort, economy and years of worry-free performance.
800
700
600
500
ncy
fficie
nal E
o
s
a
Se
51.4%
y
fficienc
onal E
s
a
e
S
82.0%
400
Based on Dept.
of Energy test
procedures.
Figures are
based on 60¢
per therm of
natural gas.
35
40
45
50
DESIGN HEATING REQUIREMENTS
(Heat loss measured in thousand Btu per hour.)
This graph illustrates the difference in annual operating costs between boilers with
higher and lower efficiencies. Boilers installed years ago have seasonal efficiencies
as low as 50%. So, your savings in fuel dollars with Columbia’s CEG-C boiler can
repay its installed cost in a few short years!
Stainless Steel Burners
Advanced design, corrosion resistant stainless steel
burners are incorporated into each CEG-C boiler
delivering uniform flame patterns that optimize
combustion efficiency and quiet operation.
COLUMBIA
Built-In Safety Devices
Factory Tested, Ready to Install
Following a series of rigorous tests, each CEG-C boiler
leaves Columbia Boilers as a completely packaged and
crated unit — ready to install and fire.
Manufacturer’s Warranty
The Columbia Boilers CEG-C is covered by a manufacturer’s
10-year warranty for residential installations. In addition,
your heating system is backed by an American
commitment to quality that is synonymous with the
Columbia Boilers name.
CEG-C Boiler Features
• Cast Iron Sections
• Corrosion Resistant Stainless Steel Burners
• Water-Tight Cast Iron Push Nipples
• Standard or Electronic Ignition
• 112,500-299,999 BTU/h input
• Integral Draft Hood, Natural Draft Conventional
Chimney Vented
• Natural Gas or Propane
The CEG-C is equipped with
a number of safety devices
that protect your family. A
low water cut-off constantly
monitors water
levels, aiding in
preventing a
“dry-firing” and
potential boiler failure. In addition,
two thermally activated safety
sensors automatically shut off the gas
burners should the chimney or heat
exchanger become
blocked. No guess
work when your safety
is concerned.
®
CEG c-C Series
Natural Gas Steam Boilers
SERIES PEG-C NATURAL
GAS STEAM BOILERS
NET I=B=R
DIMENSIONS
BOILER
NUMBER
CEG112C
CEG150C
CEG187C
CEG225C
CEG262C
CEG300C
*A G A
INPUT
BTU/HR.
HEATING
CAPACITY
BTU/HR.
STEAM
RATING
BTU/HR
112,500
150,000
187,500
225,000
262,500
299,999
90,000
120,000
151,000
181,000
212,000
243,000
67,500
90,000
113,300
135,800
159,000
182,300
SQ. FT.
GAS
INLET
SIZE
A
B
C
D
E
F
G
281
375
472
556
663
760
1/2
1/2
1/2
3/4
3/4
3/4
141⁄4
171⁄8
20
2213⁄16
255⁄8
281⁄8
275⁄8
285⁄8
295⁄8
305⁄8
305⁄8
315⁄8
241⁄8
245⁄8
251⁄8
255⁄8
255⁄8
261⁄8
5
6
7
8
8
9
31⁄2
4
41⁄2
5
5
51⁄2
6
61⁄2
7
8
8
10
443⁄4
451⁄4
453⁄4
463⁄4
463⁄4
483⁄4
ANNUAL FUEL
UTILIZATION EFFICIENCY
(AFUE)
ELECT.
STD.
IGN. &
PILOT &
DAMPER DAMPER
82.0
82.0
82.0
82.0
82.0
81.0
78
78
78
78
78
78
*NOTE: For altitudes above 2,000 ft., ratings should be reduced at the rate of 4% for each 1,000 ft. above sea level.
STANDARD EQUIPMENT: Crated Cast Iron Boiler, Drafthood, Low Water Cut-off (Probe Type), Deluxe Jacket, Wiring, Automatic
Vent Damper, Stainless Steel Burners, Blocked Vent and Roll-out Safety Switches, Gas Valve, Pilot, Pressure High Limit Control,
Pressure Gauge, Gauge Glass, 2-2" Supply Tapping, 2-2" Return Tappings - L.H. Plugged. Packed in a separate carton: Pop Safety
Valve and Boiler Drain. Stack Damper shipped in separate cartons within the crate on all models except CEG300C.
OPTIONAL EQUIPMENT: Combination low-water cut-off and feeder, CSD-1 controls.
DIMENSIONS
Tested for
15 lbs. ASME
Working Pressure
LEFT SIDE VIEW
FRONT VIEW
RIGHT SIDE VIEW
EXPLANATION NOTES
The Ratings marked “Net I=B=R Ratings”
indicate the amount of equivalent direct
cast iron radiation each boiler will take
care of under normal conditions and
thermostatic control. The Net I=B=R
Steam Ratings shown are based on a
piping and pickup allowance of 1.333.
Proper allowance has been made for
piping and pickup in accordance with the
factors shown in the I=B=R Standard as
published by The Hydronics Institute.
COLUMBIA
COLUMBIA
BOILER
COMPANY
®
Selection of boiler size should be based
on the net BTU per hour output of the
connected radiation and system piping.
The manufacturer should be consulted
before selecting a boiler for installations
having unusual piping and pickup
requirements, such as intermittent
system operation, extensive piping
systems, etc.
Specifications and dimensions are subject
to change without notice.
MEA# 17-79
YOUR ASSURANCE
OF QUALITY
Columbia Boilers products are
designed, tested, and assembled to
ensure that you get the very best
in home heating comfort and value.
Each one meets or exceeds all
recognized safety, performance,
and efficiency standards.
For more information on Columbia Boilers heating products contact your local Columbia
Boilers distributor or call Columbia Boilers at (410) 242-5300 or (610) 323-9200.
Columbia Heating Products
Columbia Heating Supply
1409 Rome Road, PO Box 24202
Baltimore, MD 21227
Tel 410-242-5300 Fax 410-247-5026
Web Site: www.columbiaheating.com
390 Old Reading Pike, PO Box 377
Pottstown, PA 19464
Tel 610-323-9200 Fax 610-323-8532
Form No. CEG-C 9/07