Extron MTP T 15HD A Architectural Series Setup

Product Category
e
NT:
RTA.com for thtion
O
P
IM
tron
talla
w.ex uide, ins ations.
o ww
Go t te user g specific
nd
ple
com ctions, a
u
instr
MTP T 15HD A Architectural Series • Setup Guide
The Extron MTP T 15HD A Architectural twisted pair transmitter series accept VGA and audio signals.
zz
MTP T 15HD A WM
AUDIO IN
zz
MTP T 15HD A D
COMPUTER IN
zz
MTP T 15HD A AAP
This guide provides instructions for an installer to set up and operate these products. For detailed information,
see the MTP T 15HD A Architectural Twisted Pair Transmitters User Guide, available at www.extron.com.
MTP T 15HD A
Pre-installation
Pins:
12345678
The MTP T 15HD A WM and D models are installed in a 1-gang electrical wall box. The
MTP T 15HD A AAP is attached to a device faceplate or an AAP wall plate. Install the
electrical box or wall plate (see the MTP T 15HD A Architectural Twisted Pair Transmitters
User Guide).
T568A
Pin Wire Color
1 White-green
T568B
Wire Color
White-orange
2 Green
Before installation, run the twisted pair (TP) and audio output cables from the output
device to the transmitter.
NOTE:
The cable must be terminated using the same standard (A or B) at
both ends (see figure 1).
Insert Twisted
Pair Wires
Orange
3 White-orange
White-green
4 Blue
Blue
5 White-blue
White-blue
6 Orange
Green
7 White-brown
White-brown
8 Brown
Brown
NOTE: If you are using Enhanced Skew-Free™
A/V cable, use the TIA/EIA T568A standard only.
Run cables from the 12 VDC power supply to the transmitter.
Figure 1. TP Termination Diagram
Installation
Step 1 — Rear Panel Cabling and Adjustments
ATTENTION:
See “Power Supply Wiring” in the user guide before wiring.
Ridges
A
A
SECTION A–A
Power Supply
Output Cord
MTP T 15HD WM and AAP Power Supply Wiring
POWER
12V
.5A MAX
Wire the 2-pole captive screw connectors as shown in the figures to the right. Plug them into the Power
connectors of the MTPs. The LED indicator on each MTP should be on when receiving power.
Smooth
Ridges
A
Grounding guidelines:
Extron MTP 15HD A products can be adversely affected by electrostatic discharge (ESD) if they are not
grounded correctly.
3/16"
(5 mm)
Max.
Smooth
Rear
Panel
A
Tie
Wrap
0.2" (5 mm) MA
Ridges
To prevent malfunctions or product damage, an experienced installer can correctly ground an
A
Extron MTP 15HD A Architectural series product by grounding the power input port. Insert one end of the
grounding wire to the negative or ground pin on the power input connector (see the figure to the right).
Tie the other end of the wire to an earth ground.
A
SECTION A–A
SECTION
A–A
Power Supply
Power Supply
Output
Cord
Output Cord
Captive Screw
Connector
Power — Connect the cables from the included external 12 VDC power supply to the rear panel
3.5 mm, 2-pole captive screw connector.
Smooth
Captive Screw
Connector
0.2" (5 mm) MAX
Turn off or disconnect all equipment power sources. Before mounting the transmitter, make the
following connections and adjustments:
Ridges
Earth
Ground
MTP T 15HD A D Power Supply Wiring
If you have any questions about how to ground a product in a specific application, contact an
Extron technical support specialist.
Pre-Peaking — For long cable runs, set the rear panel pre-peaking switch
to On (see the images to the right). For detailed information, see the
MTP T 15HD A Architectural Twisted Pair Transmitters User Guide.
ON
PREPEAK
OFF
Output Cabling — Connect the TP cable to the rear panel RJ-45 connector.
50
ON
PREPEAK
Hz
60
MTP T 15HD A D
OFF
MTP T 15HD WM and AAP
Audio Cabling — For local stereo output, insert stripped audio cable into the rear panel, direct
insertion, 3.5 mm, 5-pole captive screw connector (see the figure below).
EDID Configuration (A D units) — See the EDID Minder section on the rear of this Setup Guide
for information on configuring the EDID.
Unbalanced Stereo Input
R
Tip
Sleeve
Tip
Ring
Sleeve (s)
Tip
Ring
L
Tip
Sleeve
R
For unbalanced audio, connect the sleeves
to the center contact ground.
DO NOT connect the sleeves to the
negative (-) contacts.
L
ATTENTION: Potential damage to property.
Balanced Stereo Input
1
MTP T 15HD A Architectural Series • Setup Guide (Continued)
Step 2 — Mounting
Secure the transmitter to the electrical box, device faceplate, or wall plate.
Figure 2 shows a Decora model mounted in a wall box.
Step 3 — Connect the Inputs
Connect the video and audio inputs to the front panel connectors:
10
High resolution video input — Connect the video input to the 15‑pin HD
connector
(for RGB, composite, S-video, or component video signals).
5
15
1
6
11
Wall Box
Female
NOTES:
• For input only sync signals (no video signals), use sync pins 13 and 14.
• For component video, use the R (R-Y) and R return pins (pins 1 and 6), G (Y)
Wall opening
is flush with
edge of box.
DIO
AU
UT
PC
INP
and G return pins (pins 2 and 7), and B (B-Y) and B return pins (pins 3 and 8).
• For S-video, use the R, R return (C-chroma), G, and G return (Y-luma) pins.
• For composite video, use the G pin and the associated return pin. For
MTP T 15HD A D
Decora
Faceplate
additional genlocked video signals, use the R, B, and associated return pins.
Audio input — Plug a 3.5 mm stereo audio plug into this jack for unbalanced audio input.
Wire the plug as shown in the diagram to the right.
Figure 2. MTP T 15HD A D Mounting
Tip (L)
Ring (R)
Step 4 — Connect the Output Devices
Connect the TP cable from the transmitter to the input port of an MTP receiver.
Connect the audio output cables (see Audio Cabling in step 1) to a local audio system.
Sleeve ( )
EDID Minder
The MTP T 15HD A D unit supports emulation of factory-installed EDID information through EDID Minder.
To use factory-installed EDID information:
1.
If you have not already done so, connect the source device to the MTP 15HD transmitter.
Do not power on the source device at this time.
2.
Set the rear panel DIP switch (a) to the required frequency (50 or 60 Hz).
NOTE:
When the rotary dial (b) is set to position 0, the frequency DIP
switch position is ignored.
3.
Set the rotary dial (b) to the required position (see the table in figure 5).
Positions 1 through F are factory installed. Position 0 is not used.
ON
Rotary Switch
Position
Resolution
0
Not used
50
PREPEAK
Hz
OFF
1
60
EDID
SELECT
2
Figure 4. MTP Transmitter Rear Panel
2
© 2013 Extron Electronics All rights reserved. www.extron.com
1
800x600
2
1024x768 (default)
3
1280x720
4
1280x768
5
1280x800
6
1280x1024
7
1360x768
8
1366x768
9
1400x1050
A
1400x900
B
1600x900
C
1600x1200
D
1680x1050
E
1920x1080
F
1920x1200
Figure 5. EDID Settings Table
68-2207-50
Rev. B
03 13