Q2202wb
LCD Display
IMPORTANT: Please read this User Guide to obtain important
information on installing and using your product in a safe manner, as
well as registering your product for future service. Warranty information
contained in this User Guide will describe your limited coverage from
ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the
Regional selection box in the upper right corner of our website.
“Antes de operar su equipo lea cuidadosamente las instrucciones en
este manual”
Model No. : VS12107
Contents
Compliance Information.............................................................................. 1
Important Safety Instructions...................................................................... 2
Declaration of RoHS Compliance............................................................... 3
Copyright Information ................................................................................. 4
Product Registration ................................................................................... 4
Getting Started
Package Contents ...................................................................................... 5
Precautions ................................................................................................ 5
Quick Installation ........................................................................................ 6
Using the LCD Display
Setting the Timing Mode............................................................................. 7
Control Buttons........................................................................................... 7
OSD (On-Screen Display) Menu Mode ...................................................... 8
Other Information
Specifications ............................................................................................. 9
Troubleshooting........................................................................................ 10
Customer Support .................................................................................... 11
Cleaning the LCD Display ........................................................................ 12
Limited Warranty ...................................................................................... 13
Mexico Limited Warranty .......................................................................... 15
Optiquest
Q2202wb
i
ENGLISH
Compliance Information
For U.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
For Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the requirements of the EEC directive 2004/108/EC
as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to
"Electromagnetic compatibility", and 2006/95/EC as amended by 93/68/EEC
Art.13 with regard to "Safety."
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted
municipal waste, but use the return and collection systems according to local law.
1
Optiquest
Q2202wb
ENGLISH
Important Safety Instructions
1.
Read these instructions completely before using the equipment.
2.
Keep these instructions in a safe place.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
6.
Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in
this guide for further instructions.
7.
Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
9.
Do not attempt to circumvent the safety provisions of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third prong are
provided for your safety. If the plug does not fit into your outlet, consult an electrician for
replacement of the outlet.
10. Protect the power cord from being tread upon or pinched, particularly at the plug, and the
point where if emerges from the equipment. Be sure that the power outlet is located near
the equipment so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the equipment. When a cart is used, use caution
when moving the cart/equipment combination to avoid injury from tipping
over.
13. Unplug this equipment when it will be unused for long periods of time.
14. Refer all servicing to qualified service personnel. Service is required when the unit has
been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid
is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if
the unit does not operate normally or has been dropped.
Optiquest
Q2202wb
2
ENGLISH
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of
the European Parliament and the Council on restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply
with the maximum concentration values issued by the European Technical Adaptation
Committee (TAC) as shown below:
Substance
Proposed Maximum Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
Certain components of products as stated above are exempted under the Annex of the RoHS
Directives as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not
specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic
ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.
3
Optiquest
Q2202wb
Copyright © ViewSonic® Corporation, 2008. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of
Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and
DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets
the ENERGY STAR® guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right
to change product specifications without notice. Information in this document may change
without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic
Wizard CD-ROM also provides an opportunity for you to print the registration form, which
you may mail or fax to ViewSonic.
For Your Records
Product Name:
Q2202wb
Optiquest 21.6” LCD Display
Model Number:
VS12107
Document Number:
Q2202wb-1_UG_ENG Rev. 1C 09-02-08
Serial Number:
______________________________
Purchase Date:
______________________________
Product disposal at end of product life
The lamp in this produc contains mercury. Please dispose of in accordance with local, state or
federal laws.
ViewSonic is concerned about the preservation of our environment. Please dispose of this
product properly at the end of its useful life. For the recycling information, please refer to our
website:
1. USA: www.viewsonic.com/pdf/RecyclePlus.pdf
2. Europe: www.viewsoniceurope.com
3. Taiwan: recycle.epa.gov.tw
Optiquest
Q2202wb
4
ENGLISH
Copyright Information
ENGLISH
Getting Started
Congratulations on your purchase of a ViewSonic® LCD display.
Important! Save the original box and all packing material for future shipping needs.
NOTE: The word “Windows” in this user guide refers to the following Microsoft operating
systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me
(Millennium), and Windows XP.
Package Contents
Your LCD display package includes:
• LCD display
• Power cord
• Audiokaapeli
• D-Sub cable
• User Guide
Precautions
• Sit at least 18” from the LCD display.
• Avoid touching the screen. Skin oils are
difficult to remove.
• Place the LCD display in a well ventilated
area. Do not place anything on the LCD
display that prevents heat dissipation.
• Never remove the rear cover. This LCD
display contains high-voltage parts. You
may be seriously injured if you touch
them.
• Ensure the area around the LCD display is
clean and free of moisture.
• Avoid exposing the LCD display to direct
sunlight or another heat source. Orient the
LCD display away from direct sunlight to
reduce glare.
• If smoke, an abnormal noise, or a strange
odor is present, immediately switch the
LCD display off and call your dealer or
ViewSonic. It is dangerous to continue
using the LCD display.
• Always handle the LCD display with care
when moving it.
5
• Do not place heavy objects on the LCD
display, video cable, or power cord.
• Do not rub or apply pressure to the LCD
panel, as it may permanently damage the
screen.
Optiquest
Q2202wb
1. Connect power cord (and AC/DC
adapter if required)
ENGLISH
Quick Installation
(resolution and refresh rate)
Example: 1680 x 1050 @ 60 Hz.
2. Connect video cable
For instructions on changing the resolution
and refresh rate, see the graphics card’s
user guide.
• Make sure both the LCD display and
computer are turned OFF
• Remove rear panel covers if necessary
Installation is complete. Enjoy your new
ViewSonic LCD display.
• Connect the video cable from the LCD
display to the computer
Macintosh users: Models older than G3
require a Macintosh adapter. Attach the
adapter to the computer and plug the video
cable into the adapter.
To order a ViewSonic® Macintosh adapter,
contact ViewSonic Customer Support.
To be best prepared for any future
customer service needs: print this user
guide and write the serial number in “For
Your Records” on page 4. (See back of
LCD display.)
You can register your product online at the
ViewSonic website for your region. See
the Customer Support table in this guide.
3. Turn ON LCD display and computer
Turn ON the LCD display, then turn ON
the computer. This sequence (LCD display
before computer) is important.
4. Windows users: Set the timing mode
AC IN
D-SUB
Power cord
AC Outlet
(Wall Socket)
Computer Power Cord
Optiquest
Q2202wb
6
ENGLISH
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the screen image and
minimizing eye strain. The timing mode consists of the resolution (example 1680 x 1050) and
refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the
OSD (On-screen Display) controls to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1680 x 1050 @ 60Hz.
To set the Timing Mode:
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the
resolution.
2. Set the refresh rate: See your graphic card's user guide for instructions.
WARNING: Do not set the graphics card in your computer to exceed the maximum refresh
rate of 75Hz; doing so may result in permanent damage to your LCD display.
Control Buttons
There are 5 keys for user to set up the monitor, including "Auto Adjust", "OSD menu",
"Power", "Adjust <->", "Adjust <+>". The following descriptions are the introduction of these
Keys.
A
M
+
7
Auto Adjust (Function)
Function Select Button: This button allows you to select the control
functions up in the OSD.
Hotkey: Press this button to apply the monitor setting automatically.
Menu (Function)
Function Select Button: This button allows you to select the control
functions down in the OSD.
Hotkey: Press this button to get a pop-up OSD menu.
Power: Turn the LCD power on and off. When the power is on, the
light is showing blue, standby mode will be flash.
Adjust < - >: Decrease the option value in the OSD menu.
Adjust < + >: Increase the option value in the OSD menu.
Optiquest
Q2202wb
*Please adjust your Speaker Volume via your PC computer Speaker Volume control icon.
*Please note that Sound will continue to play when your monitor is off, to turn off please turn
off your PC computer or mute the Speaker Volume control icon.
Press the OSD button to access menu, and press Increase / Decrease button for adjustment.
BRIGHTNESS
CONTRAST
PHASE
CLOCK
H-POSITION
V-POSITION
RESET
COLOR
TEMPERATURE
RED
GREEN
BLUE
LANGUAGE
Adjust the brightness of the display.
Adjust the difference between light and dark area.
The phase of the dot clock is adjusted.
The ratio of dividing frequency of the dot clock is adjusted.
Adjust the horizontal position of the display.
Adjust the vertical position of display.
Recall the default setting.
Adjust the color temperature.
Adjust the Red color temperature.
Adjust the Green color temperature.
Adjust the Blue color temperature.
Select the display language of the OSD Menu.
“No” will take you to the exit menu.”Yes” will bring you to the sub
MISCELLANEOUS
menus of the Miscellaneous menu.
EXIT OSD
Saving and Leave.
MISCELLANEOUS
RETURN
OSD H-POSITION
OSD V-POSITION
OSD DURATION
AUTO COLOR
Optiquest
Return to main menu.
Adjust the horizontal position of the OSD.
Adjust the vertical position of the OSD.
Adjust the timing of the OSD menu.
Adjust the color automatically.
Q2202wb
8
ENGLISH
OSD (On-Screen Display) Menu Mode
ENGLISH
Other Information
Specifications
LCD
Type
Color Filter
Glass Surface
22” (full 21.6" viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix WSXGA+ LCD,
0.276 mm pixel pitch
RGB vertical stripe
Anti-Glare
Input Signal
Video Sync
RGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync
fh:30-80 kHz, fv:55-75 Hz
Compatibility
PC
Macintosh1
Up to 1680 x 1050 Non-interlaced
Power Macintosh up to 1680 x 1050
Resolution
Recommended
and supported
1600 x 1200 @ 60 Hz
1680 x 1050 @ 60 Hz
1440 x 900 @ 60, 75 Hz
1280 x 1024 @ 60, 75 Hz
1280 x 800 @ 60, 75 Hz
1024 x 768 @ 60, 70, 75 Hz
800 x 600 @ 56, 60, 75 Hz
640 x 480 @ 60, 72, 75 Hz
720 x 400 @ 70 Hz
Power
Voltage
100-240 VAC, 50-60 Hz (auto switch)
Display area
Full Scan
464.94 mm (H) x 290.59 mm (V)
18.3" (H) x 11.44" (V)
Operating
conditions
Temperature
Humidity
Altitude
+41° F to +104° F (+5° C to +40° C)
20% to 80% (non-condensing)
To 13,000 feet
Storage
conditions
Temperature
Humidity
Altitude
-4° F to +140° F (-20° C to +60° C)
20% to 85% (non-condensing)
To 40,000 feet
Dimensions
Physical
525.63 mm (W) x 433.47 mm (H) x 172.77 mm (D)
20.69" (W) x 17.06" (H) x 6.8" (D)
Weight
Physical
10.14 lb (4.6 kg)
Regulations
Power saving
modes
BSMI, C-Tick, MIC, CE, ISO 13406-2, Gost-R/Hygienic, Ukraine,
UL/cUL, FCC-B, ICES-B, TUV-S/IRAM/UL-AR S Mark, NOM,
ENERGY STAR®
On
Off
45W (Typical)
<1W
(blue LED)
Preset Timing Mode (pre-adjusted to VESA® 1680 x 1050 @ 60 Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may result in
permanent damage to the LCD display.
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic.
9
Optiquest
Q2202wb
ENGLISH
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video
output port on the back of the computer. If the other end of the video cable is not attached
permanently to the LCD display, tightly secure it to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is
securely connected. Loose or broken pins in the cable connector could cause an improper
connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic® for a non-DDC adapter.
Control buttons do not work
• Press only one button at a time.
Optiquest
Q2202wb
10
ENGLISH
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/Region
Website
T = Telephone
F = FAX
Email
Australia/New Zealand
www.viewsonic.com.au
AUS= 1800 880 818
NZ= 0800 008 822
service@au.viewsonic.com
Canada
www.viewsonic.com
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
service.ca@viewsonic.com
F= 1-909-468-1202
Europe/Middle East/
Baltic countries/North
Africa
www.viewsoniceurope.com Contact your reseller
Hong Kong
www.hk.viewsonic.com
T= 852 3102 2900
service@hk.viewsonic.com
India
www.in.viewsonic.com
T= 1800 11 9999
service@in.viewsonic.com
Korea
www.kr.viewsonic.com
T= 080 333 2131
service@kr.viewsonic.com
Latin America
(Argentina)
www.viewsonic.com/la/
T= 0800 666 0194
soporte@viewsonic.com
Latin America (Brazil)
www.viewsonic.com/la/
T= 0800 891 6984
soporte@viewsonic.com
Latin America (Chile)
www.viewsonic.com/la/
T= 800 440 303
soporte@viewsonic.com
Latin America
(Columbia)
www.viewsonic.com/la/
T= 01 800 915 6588
soporte@viewsonic.com
Latin America (Mexico)
www.viewsonic.com/la/
T= 001 800 514 6518
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
www.viewsonic.com/la/
T= 0800 53458
soporte@viewsonic.com
Macau
www.hk.viewsonic.com
T= 853 700 303
service@hk.viewsonic.com
Puerto Rico & Virgin
Islands
www.viewsonic.com
T= 1-800-688-6688 (English)
service.us@viewsonic.com
T= 1-866-379-1304 (Spanish)
soporte@viewsonic.com
F= 1-909-468-1202
Singapore/Malaysia/
Thailand
www.ap.viewsonic.com
T= 65 6461 6044
South Africa
www.viewsoniceurope.com www.viewsoniceurope.com/uk/Support/Calldesk.htm
United Kingdom
www.viewsoniceurope.com
www.viewsoniceurope.com/uk/Support/Calldesk.htm
/uk/
United States
www.viewsonic.com
11
service@sg.viewsonic.com
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
service.us@viewsonic.com
F= 1-909-468-1202
Optiquest
Q2202wb
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE.
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If the screen still not clean, apply a small amount of non-ammonia, non-alcohol based glass
cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If the case still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild
non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
• ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the
LCD display screen or case. Some chemical cleaners have been reported to damage the
screen and/or case of the LCD display.
• ViewSonic will not be liable for damage resulting from use of any ammonia or alcoholbased cleaners.
Optiquest
Q2202wb
12
ENGLISH
Cleaning the LCD Display
ENGLISH
Limited Warranty
VIEWSONIC® LCD DISPLAY
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under
normal use, during the warranty period. If a product proves to be defective in material or
workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace
the product with a like product. Replacement product or parts may include remanufactured or
refurbished parts or components.
How long the warranty is effective:
ViewSonic LCD displays are warranted for 1 year for all parts including the light source and 1
year for all labor from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic’s specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as "image burn-in" which results
when a static image is displayed on the product for an extended period of time.
4. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial
number.
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip,
(b) your name, (c) your address, (d) a description of the problem, and (e) the serial number
of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained
herein including the implied warranty of merchantability and fitness for a particular purpose.
4.3: ViewSonic LCD Warranty
13
Page 1 of 2
LCD_LW02 Rev. 1b 06-11-07
Optiquest
Q2202wb
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss,
even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow limitations on implied warranties and/or do not
allow the exclusion of incidental or consequential damages, so the above limitations and
exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and
Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan
Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
4.3: ViewSonic LCD Warranty
Optiquest
Q2202wb
Page 2 of 2
LCD_LW02 Rev. 1b 06-11-07
14
ENGLISH
Exclusion of damages:
ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic
shall not be liable for:
ENGLISH
Mexico Limited Warranty
VIEWSONIC® DISPLAY PRODUCTS
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during
the warranty period. If a product proves to be defective in material or workmanship during the warranty period,
ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts
may include remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
ViewSonic LCD displays are warranted for 1 year for all parts including the light source and 1 year for all labor
from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic's specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
7. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is
displayed on the product for an extended period of time.
8. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product's serial number, so please record the
product information in the space provided below on your purchase for your future use. Please retain your receipt
of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________________
Model Number: _____________________________
Document Number: ____________________________
Serial Number: _____________________________
Purchase Date: ________________________________
Extended Warranty Purchase? ____________ (Y/N)
If so, what date does warranty expire? ___________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable
for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of
use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with
business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
4.3: ViewSonic Mexico Limited Warranty
15
Page 1 of 2
LCD_LW03 Rev. 1a 06-11-07
Optiquest
Q2202wb
4.3: ViewSonic Mexico Limited Warranty
Optiquest
Q2202wb
Page 2 of 2
LCD_LW03 Rev. 1a 06-11-07
16
ENGLISH
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099
http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Villahermosa:
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV. Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
Calle Juarez 284 local 2
COL, FLORIDA C.P. 86040
Col. Bugambilias C.P: 83140
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
Tel: 01-66-22-14-9005
E-Mail: compumantenimientos@prodigy.net.mx
E-Mail: disc2@hmo.megared.net.mx
Veracruz, Ver.:
Puebla, Pue. (Matriz):
CONEXION Y DESARROLLO, S.A DE C.V. Av.
RENTA Y DATOS, S.A. DE C.V. Domicilio:
Americas # 419
29 SUR 721 COL. LA PAZ
ENTRE PINZÓN Y ALVARADO
72160 PUEBLA, PUE.
Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS
Tel: 01-22-91-00-31-67
E-Mail: datos@puebla.megared.net.mx
E-Mail: gacosta@qplus.com.mx
Cuernavaca
Chihuahua
Compusupport de Cuernavaca SA de CV
Soluciones Globales en Computación
Francisco Leyva # 178 Col. Miguel Hidalgo
C. Magisterio # 3321 Col. Magisterial
C.P. 62040, Cuernavaca Morelos
Chihuahua, Chih.
Tel: 01 777 3180579 / 01 777 3124014
Tel: 4136954
E-Mail: aquevedo@compusupportcva.com
E-Mail: Cefeo@soluglobales.com
Guadalajara, Jal.:
Distrito Federal:
SERVICRECE, S.A. de C.V.
QPLUS, S.A. de C.V.
Av. Niños Héroes # 2281
Av. Coyoacán 931
Col. Arcos Sur, Sector Juárez
Col. Del Valle 03100, México, D.F.
44170, Guadalajara, Jalisco
Tel: 01(52)55-50-00-27-35
Tel: 01(52)33-36-15-15-43
E-Mail : gacosta@qplus.com.mx
E-Mail: mmiranda@servicrece.com
Monterrey:
Guerrero Acapulco
Global Product Services
GS Computación (Grupo Sesicomp)
Mar Caribe # 1987, Esquina con Golfo Pérsico
Progreso #6-A, Colo Centro
Fracc. Bernardo Reyes, CP 64280
39300 Acapulco, Guerrero
Monterrey N.L. México
Tel: 744-48-32627
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
Oaxaca, Oax.:
MERIDA:
CENTRO DE DISTRIBUCION Y
ELECTROSER
SERVICIO, S.A. de C.V.
Av Reforma No. 403Gx39 y 41
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Mérida, Yucatán, México CP97000
Tel: 01(52)95-15-15-22-22
Tel: (52) 999-925-1916
Fax: 01(52)95-15-13-67-00
E-Mail: rrrb@sureste.com
E-Mail. gpotai2001@hotmail.com
FOR USA SUPPORT:
Tijuana:
ViewSonic Corporation
STD
381 Brea Canyon Road, Walnut, CA. 91789 USA
Av Ferrocarril Sonora #3780 L-C
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Col 20 de Noviembre
Fax: 1-800-685-7276
Tijuana, Mexico
E-Mail: http://www.viewsonic.com