Weidmuller Wireless Brochure

Wireless Connectivity Solutions
Product Information
Contents
Product Overview
Introduction
3
Wireless I/O
Unidirectional Transmitter/Receiver Units
Introduction
Product Data
4
5
Multi I/O Units
Introduction
Product Data
7
8
Expansion I/O Units
Introduction
Product Data
10
11
Transmitter (Single Sensor Units)
Introduction
Product Data
13
14
Wireless Gateways
Introduction
Product Data
15
16
Wireless Data Modems
Introduction
Product Data
19
20
Wireless GPRS Modem
23
Accessories
24
2
P ro d u c t O v e r v i e w
Types of Wireless Products
Product Overview
Weidmuller industrial wireless products provide secure and
reliable solutions for a wide range of industries and applications,
as an alternative for signal and data wiring. These products fall
into four groups:
Wireless I/O, also known as radio telemetry, connect directly
to sensor and control signals, and transmit the signal values by
radio. The signals are either re-created as similar signals, or output as a data connection — Ethernet, Profibus, Modbus etc.
Wireless I/O networks can be as simple as two units transferring
a small number of signals from one point to another, or they can
be complex data-acquisition networks with multiple “master”
interfaces to external systems.
Wireless I/O
Wireless Gateways provide wireless connectivity between
data buses - connectivity between devices using the same
data bus, or between different data buses (Ethernet to Profibus
to DeviceNet to Modbus etc). Wireless gateways are similar in
operation to wireless modems, however gateways only provide
a register interface to the data bus, transferring I/O registers only.
Wireless Gateways
Wireless Modems transmit serial or Ethernet data, providing
a wireless extension of the data link. Example applications are
PLC to PLC connections (point-to-point), connecting SCADA
to a group of PLCs (point-to-multipoint), or forming a wireless
PLC LAN (multidrop). Wireless modems transmit the data with
minimal transformation.
Wireless Modems
Wireless GPRS Alarm Modems use GPM mobile technology
to provide alarm and status information directly to a mobile
device, SMS, email, or via fax. The GPRS Alarm Modem can
be located anywhere GSM reception is available. Site, remote
location, or plant monitoring can be conducted remotely without
the need for onsite employees.
Wireless GPRS Modem
3
W i re l e s s I / O U n i d i re c t i o n a l Tr a n s m i t t e r / R e c e i v e r U n i t s – I n t ro d u c t i o n
Wireless Input/Output (I/O)
Wireless I/O connects directly to analog, discrete and pulse transducer signals. The signals are transmitted by radio and either
re-created as output signals, or output via serial link or field-bus.
Weidmuller Wireless I/O units have the ability to form sophisticated peer-to-peer networks, with event-reporting messaging
to optimize wireless density. Weidmuller products are designed for high reliability operation on open license-free radio bands.
WI-I/O 9-L Unidirectional Transmitter/Receiver Units
• Frequency hopping spread spectrum 902-928 MHz 1W license-free USA/Canada
• Configurable sub-bands license-free Mexico, South America, Australia/NZ, Hong Kong
The Unidirectional Wireless I/O range of products is suitable for connecting to a single sensor or group of sensors and provides an
economical solution for remote monitoring systems. The Unidirectional L products can also be used in more complex networks as
signal transmitters or receivers
Features
Matched transmitter/receiver pair of modules, or individual transmitter and receiver units
• Peer-to-peer communications. Exception reporting. Reliable self-checking messages. Highly secure data encryption.
• Multi-hop repeater functions - up to 5 intermediate units can be configured in any input-output link
• Factory configured as a matched Transmitter/Receiver pair or user-configurable with E-Series Windows configuration program
Transmitter unit
• Input-only transmitter unit - two digital/pulse inputs, one analog input and one thermocouple mV input
• Transmits to Receiver unit as a matched pair where the input signals are re-created as output signals,
or can transmit to a Multi-I/O or Gateway unit
• Class 1 Div 2 hazardous areas approval (USA/Canada)
• Up to 3000 wireless units per network
• External inputs plus internally calculated values - analog setpoint status, pulse count, power supply voltage
• Thermocouple input –100 to +100mV with cold-junction compensation and linearization for J, K or T-type
• Setpoints status generated by comparing analog input to high and low setpoints
• Digital inputs can also be used as pulse count inputs
• Power supply 9 – 30VDC, measured and available as a transmitted variable
• 24VDC analog loop supply internally provided
• RS232 Configuration and diagnostics port
Receiver unit
• Output-only receiver unit - three digital contact outputs and one analog output
• Receives radio commands from Transmitter unit as a matched pair where the input signals are re-created as output signals,
or can receive commands from a Multi-I/O or Gateway unit
• Class 1 Div 2 hazardous areas approval (USA/Canada)
• Up to 3000 wireless units per network
• Power supply 9 – 30VDC; 24VDC analog loop supply internally provided
• Communications failure indication and configurable output
• Outputs can be configured as retained or reset (fail-safe) on communications failure
• LED indication of radio signal strength
• RS232 Configuration and diagnostics port
4
900 MHz
U n i d i re c t i o n a l Tr a n s m i t t e r / R e c e i v e r U n i t s — P ro d u c t D a t a
WI-I/O 9-L-T
Transmitter
Technical Data
Transmitter Inputs:
Digital:
Pulse:
Analog:
“floating” differential input:
resolution
accuracy
Thermocouple
Accuracy
Receiver Outputs
Digital
Analog
resolution
accuracy
Comms-Fail
two inputs, suitable for voltage free contacts / NPN,
or voltage input 0-1 VDC on / >3 VDC off
max rate 10 Hz, 50 msec on time.
Pulse counted as 16 bit register.
0-20 mA (4-20mA, 0-10mA)
16 bit
< 0.1 %
Millivolt (-100mV to +100mV), J, K or T type linearization with
on-board cold-junction compensation
greater than 1°C
Fail-safe
Power Supply
Power consumption @12VDC
Analog loop supply internally generated
Internal monitoring of supply low voltage status
Power consumption increases for pulse inputs > 10Hz.
Serial Port
General Data
Operating Temperature
Humidity
Approvals
Mounting
LED indication: Transmitter Unit
LED indication: Receiver Unit
frequency hopping spread spectrum
Transmit power
Maximum line of sight range
Antenna connector
Dimensions mm (in)
Configuration
Diagnostics
Ordering Data
WI-I/O 9-L-R
Receiver
9-30 VDC
Receiver 100mA, Transmitter 40mA quiescent,
during radio transmission (50 msec) 300mA
24VDC 30mA
may be transmitted as an “input” (Transmitter unit only)
three relay contact outputs, 260V 1A
0-20mA
12 bit
0.10%
Internal status based on configurable time-out value. Commsfail status can be configured to a local output.
On “comms-fail”, outputs user-configurable as retained (last
correct value) or reset (fail-safe)
9-30 VDC
Receiver 100mA, Transmitter 40mA quiescent, during radio
transmission (50 msec) 300mA
24VDC 30mA
RS232 RJ45 female DCE, used for configuration
and diagnostics
RS232 RJ45 female DCE, used for configuration
and diagnostics
-40 to 60°C (-40 to 140°F)
0 - 99% RH
FCC Part 15.247, RS210, CSA Class 1 Div 2
DIN-rail mounting
Power/OK, Radio TX , DIN1, DIN2, Analog Setpoint status
-40 to 60°C (-40 to 140°F)
0 - 99% RH
FCC Part 15.247, RS210, CSA Class 1 Div 2
DIN-rail mounting
902-928MHz, sub-bands available
1W
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m in
obstructed industrial environments. Radio distances can be
increased by up to 5 intermediate repeater units.
Each transmission may be configured to be sent 1 to 5 times.
SMA connector for antenna or coaxial cable connection.
100 x 22 x 120 (3.9 x 0.9 x 4.7)
User configuration via serial port. Unidirectional units can be
configured to network with Multi-I/O and Gateway units.
Diagnostics features - read input values, write output values,
radio signal strength, monitor communication messages.
Type
Part No.
WI-I/O 9-L-T
6720005005
Power/OK, Radio RX, DO1, DO2, DO3, Communications Fail.
902-928MHz, sub-bands available
1W
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m in
obstructed industrial environments. Radio distances can be
increased by up to 5 intermediate repeater units.
Each transmission may be configured to be sent 1 to 5 times.
SMA connector for antenna or coaxial cable connection.
100 x 22 x 120 (3.9 x 0.9 x 4.7)
User configuration via serial port. Unidirectional units can be
configured to network with Multi-I/O and Gateway units.
Diagnostics features - read input values, write output values,
radio signal strength, monitor communication messages.
Type
Part No.
WI-I/O 9-L-R
6720005006
5
U n i d i re c t i o n a l Tr a n s m i t t e r / R e c e i v e r U n i t s — P ro d u c t D a t a
Technical Data
Transmitter Inputs:
Digital:
Pulse:
Analog:
“floating” differential input:
resolution
accuracy
Thermocouple
Accuracy
Receiver Outputs
Digital
Analog
resolution
accuracy
Comms-Fail
Fail-safe
Power Supply
Power consumption @12VDC
Analog loop supply internally generated
Internal monitoring of supply low voltage status
Power consumption increases for pulse inputs > 10Hz.
Serial Port
General Data
Operating Temperature
Humidity
Approvals
Mounting
LED indication: Transmitter Unit
LED indication: Receiver Unit
frequency hopping spread spectrum
Transmit power
Maximum line of sight range
Antenna connector
Dimensions mm (in)
Configuration
Diagnostics
Ordering Data
Kit Contents
6
900 MHz
WI-I/O 9-L-P1
Set - 1 Transmitter, 1 Receiver
WI-I/O 9-L-P2
Set with 2 WI-ANT-DPL-0-8
two inputs, suitable for voltage free contacts / NPN,
or voltage input 0-1 VDC on / >3 VDC off
max rate10 Hz, 50 msec on time. Pulse countedas16bit register.
0-20 mA (4-20mA, 0-10mA)
two inputs, suitable for voltage free contacts / NPN, or voltage
input 0-1 VDC on / >3 VDC off
max rate10 Hz, 50 msec on time. Pulse countedas16bit register.
0-20 mA (4-20mA, 0-10mA)
16 bit
< 0.1 %
Millivolt (-100mV to +100mV), J, K or T type linearization with
on-board cold-junction compensation
greater than 1°C
three relay contact outputs, 260V 1A
0-20mA
12 bit
0.10%
Internal status based on configurable time-out value. Commsfail status can be configured to a local output.
On “comms-fail”, outputs user-configurable as retained (last
correct value) or reset (fail-safe)
9-30 VDC
Receiver 100mA, Transmitter 40mA quiescent,
during radio transmission (50 msec) 300mA
24VDC 30mA
may be transmitted as an “input” (Transmitter unit only)
16 bit
< 0.1 %
Millivolt (-100mV to +100mV), J, K or T type linearization with
on-board cold-junction compensation
greater than 1°C
three relay contact outputs, 260V 1A
0-20mA
12 bit
0.10%
Internal status based on configurable time-out value. Commsfail status can be configured to a local output.
On “comms-fail”, outputs user-configurable as retained (last
correct value) or reset (fail-safe)
9-30 VDC
Receiver 100mA, Transmitter 40mA quiescent, during radio
transmission (50 msec) 300mA
24VDC 30mA
may be transmitted as an “input” (Transmitter unit only)
RS232 RJ45 female DCE,
used for configuration and diagnostics
RS232 RJ45 female DCE,
used for configuration and diagnostics
-40 to 60°C (-40 to 140°F)
0 - 99% RH
FCC Part 15.247, RS210, CSA Class 1 Div 2
DIN-rail mounting
Power/OK, Radio TX , DIN1, DIN2, Analog Setpoint status
Power/OK, Radio RX, DO1, DO2, DO3, Communications Fail.
902-928MHz, sub-bands available
1W
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m in
obstructed industrial environments.Radio distances can be
increased by up to 5 intermediate repeater units.
Each transmission may be configured to be sent 1 to 5 times.
SMA connector for antenna or coaxial cable connection.
100 x 22 x 120 (3.9 x 0.9 x 4.7)
Factory configuration transmitter/receiver matched pair, AI to
AO, 2DI to 2DO, SP status to DO3. User configuration via serial
port. Unidirectional units can be configured to network with
Multi-I/O and Gateway units.
Diagnostics features - read input values, write output values,
radio signal strength, monitor communication messages.
-40 to 60°C (-40 to 140°F)
0 - 99% RH
FCC Part 15.247, RS210, CSA Class 1 Div 2
DIN-rail mounting
Power/OK, Radio TX , DIN1, DIN2, Analog Setpoint status
Power/OK, Radio RX, DO1, DO2, DO3, Communications Fail.
LEDs also used to provide radio signal strength indication
902-928MHz, sub-bands available
1W
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m in
obstructed industrial environments. Radio distances can be
increased by up to 5 intermediate repeater units.
Each transmission may be configured to be sent 1 to 5 times.
SMA connector for antenna or coaxial cable connection.
100 x 22 x 120 (3.9 x 0.9 x 4.7)
Factory configuration transmitter/receiver matched pair, AI to
AO, 2DI to 2DO, SP status to DO3. User configuration via serial
port. Unidirectional units can be configured to network with
Multi-I/O and Gateway units.
Diagnostics features - read input values, write output values,
radio signal strength, monitor communication messages.
Type
Part No.
WI-I/O 9-L-P1
6720005007
• 2 Whip antennas (6720005086), WI-ANT-DPL-2-6-54
• 2 3ft. antenna connecting cables/brackets
• 1 configuration cable
Type
Part No.
WI-I/O 9-L-P2
6720005008
• 2 Dipole antennas (6720005080), WI-ANT-DPL-0-16
• 2 15ft. antenna connecting cables/brackets
• 1 configuration cable
900 MHz
W i re l e s s I / O M u l t i - I / O U n i t s — I n t ro d u c t i o n
WI-I/O 9 Multi I/O Units
• Large I/O capability with I/O expansion
• Two-way communications
• Use where communications is required in both directions
or for large I/O requirements. Each network can handle
multiple I/O applications.
• Frequency hopping spread spectrum
• 902-928 MHz 1W license-free USA/Canada
• Configurable sub-bands license-free Mexico
• Up to 95 wireless units per network
• Support up to 31 I/O expansion modules (WI-I/O-EX-I-S-XX)
per wireless unit
• Multi-hop repeater functions – up to 5 intermediate units
• Four I/O versions available:
WI-I/O 9
Digital inputs
Digital outputs
Analog inputs
Analog outputs
-1
4
-2
4
4
1
-3
0
Voltage-free contacts
8
Relay contacts
FET
FET
FET
2
6
0
0
4-20mA
0-20mA/0-10V
2
0
8
0
4-20mA
Pulse inputs
Pulse outputs
4 - 16
0-20mA/0-10V
1
4
100Hz
1 x 1KHz, 3 x 100Hz
1
100Hz
Note: Pulse and digital I/O are same connection.
-4
4 – 16
0
1 x 1KHz, 3 x 100Hz
0
4
1 x 1KHz, 3 x 100Hz
4
4
1 x 1KHz, 3 x 100Hz
• Pulse inputs generate separate pulse count and rate value;
pulse rates treated as internal analog registers with configurable maximum value.
• Wide voltage power supply, with integral UPS battery charger and solar regulator
• Power supply generates transmittable internal I/O values
• Multiple communication-failure diagnostics with output
status
• Class 1 Div 2 approval
• Radio receive signal and background RF noise measurement / logging diagnostics
• Input measurement display and output “forcing” diagnostics
• Communication logging diagnostics
• Easy-to-use E-Series Windows configuration
7
M u l t i - I / O U n i t s — P ro d u c t D a t a
900 MHz
WI-I/O 9-1
WI-I/O 9-2
four inputs
four inputs
two 4-20mA resolution 15 bit, accuracy 0.1%
six 0-20mA resolution 12 bit, accuracy 0.1%
one input (DI1)
four input(DI1-4) - first pulse input (DI1) max 1000Hz,
pulse width min 0.5ms
four relay contacts, Form A, AC, 50V 5A/ DC 30V 2A
two 4-20 mA resolution 15 bit, accuracy 0.1%
one FET output 30VDC 500mA
Technical Data
Inputs
Digital: opto-isolated (5000V) inputs suitable for voltage free
contacts or NPN transistor, contact wetting current 5 mA
Analog: “floating” differential inputs, common mode voltage
27V, 24VDC for powering external loops provided,
digital filtering 1 sec.
Pulse: as per digital inputs,
Max pulse rate 100Hz, pulse width min 5ms
Outputs
Digital
Analog: current sink to common,
max loop voltage 27V, max loop resistance 1000 ohms
Pulse: FET 30VDC 500mA max 100Hz
Power Supply
Battery supply
Normal supply
one
11.5-15.0 VDC
12-24 VAC or 15-30 VDC, over-voltage and
reverse power protected
included for 1.2-12 AHr sealed battery
for direct connection of solar panel (up to 30W)
and solar battery (100AHr)
power fail, solar charge status, and battery voltage
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
11.5-15.0 VDC
12-24 VAC or 15-30 VDC, over-voltage
and reverse power protected
included for 1.2-12 AHr sealed battery
for direct connection of solar panel (up to 30W)
and solar battery (100AHr)
power fail, solar charge status, and battery voltage
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
Serial Port
RS232/RS485
RS232
RS485
serial port 9600 baud, 8 bits, no parity, 1 stop bit
9pin DB9 female connector
max cable distance 2000 m terminal connections
serial port 9600 baud, 8 bits, no parity, 1 stop bit
9pin DB9 female connector
max cable distance 2000 m terminal connections
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
Transmit power
Sensitivity
Dimensions mm (in)
-40 to 60°C (-40 to 140°F)
0-99%RH
FCC Part 15, AS3548, 89/336/EEC, EN 301 489
CSA Class 1 Div 2
DIN rail mounting
For power supply, WDT, digital I/O
1W
-108 dB
130 x 185 x 60 (5.1 x 7.3 x 2.4)
-40 to 60°C (-40 to 140°F)
0-99%RH
FCC Part 15, AS3548, 89/336/EEC, EN 301 489
CSA Class 1 Div 2
DIN rail mounting
For power supply, WDT, digital I/O
1W
-108 dB
130 x 185 x 60 (5.1 x 7.3 x 2.4)
Battery charging circuit
Solar regulator
Internal monitoring
Notes
Ordering Data
8
Type
WI-I/O 9-1
Part No.
6720005000
Type
WI-I/O 9-2
Part No.
6720005001
900 MHz
M u l t i - I / O U n i t s — P ro d u c t D a t a
WI-I/O 9-3
WI-I/O 9-4
Technical Data
Inputs
up to 16 inputs (4 inputs + 12 selectable I/O) the 12 selectable
inputs are surge protected but not isolated
four input(DI1-4) - first pulse input (DI1) max 1000Hz, pulse
width min 0.5ms
Outputs
Digital
Analog: current sink to common,
max loop voltage 27V, max loop resistance 1000 ohms
Pulse: FET 30VDC 500mA max 100Hz
Power Supply
Battery supply
Normal supply
Battery charging circuit
Solar regulator
Internal monitoring
Notes
Serial Port
RS232/RS485
RS232
RS485
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
Transmit power
Sensitivity
Dimensions mm (in)
Ordering Data
eight FET output 30VDC 500mA
eight 0-20 mA resolution 12 bit, accuracy 0.1%
up to 16 FET output (4 inputs + 12 selectable I/O)
four (DO1-4)
four (DO1-4)
11.5-15.0 VDC
12-24 VAC or 15-30 VDC, over-voltage
and reverse power protected
included for 1.2-12 AHr sealed battery
for direct connection of solar panel (up to 30W)
and solar battery (100AHr)
power fail, solar charge status, and battery voltage
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
11.5-15.0 VDC
12-24 VAC or 15-30 VDC, over-voltage
and reverse power protected
included for 1.2-12 AHr sealed battery
for direct connection of solar panel (up to 30W)
and solar battery (100AHr)
power fail, solar charge status, and battery voltage
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
serial port 9600 baud, 8 bits, no parity, 1 stop bit
9pin DB9 female connector
max cable distance 2000 m terminal connections
serial port 9600 baud, 8 bits, no parity, 1 stop bit
9pin DB9 female connector
max cable distance 2000 m terminal connections
-40 to 60°C (-40 to 140°F)
0-99%RH
FCC Part 15, AS3548, 89/336/EEC, EN 301 489
CSA Class 1 Div 2
DIN rail mounting
For power supply, WDT, digital I/O
1W
-108 dB
130 x 185 x 60 (5.1 x 7.3 x 2.4)
-40 to 60°C (-40 to 140°F)
0-99%RH
FCC Part 15, AS3548, 89/336/EEC, EN 301 489
CSA Class 1 Div 2
DIN rail mounting
For power supply, WDT, digital I/O
1W
-108 dB
130 x 185 x 60 (5.1 x 7.3 x 2.4)
Type
WI-I/O 9-3
Part No.
6720005002
Type
WI-I/O 9-4
Part No.
6720005003
9
W i re l e s s I / O E x p a n s i o n I / O U n i t s — I n t ro d u c t i o n
900 MHz
WI-I/O–EX-1-S Expansion I/O Units (Serial I/O)
Typical Applications
Expansion I/O for WI-I/O 9 wireless units
- up to 31 x WI-I/O-EX-1-S units can be connected to each wireless unit via RS485 (up to 2 km long).
Serial I/O multiplexer
- transfer I/O via RS485— up to 32 units per multi-drop link.
Expansion I/O for Modbus devices
- up to 31 x WI-I/O-EX-1-S units can be connected to each Modbus master via RS485 (up to 2 km long).
Features
•
•
•
•
•
•
•
•
•
Multi I/O channels— monitoring and control functions
Connected via RS485 multi-drop
Selectable communications via Modbus protocol (both RTU and ASCII formats)
Sensor signals connected at one module (input signals) are transmitted to another module where the signals are re-created
as output signals, or passed via serial to a host device such as a PLC or SCADA system
Connect to WI-I/O 9 wireless I/O units for up to 31 serial addresses per wireless unit
Connect WI-I/O-EX-1-S units together to form a serial multi-drop I/O system - up to 32 serial addresses per multi-drop link—
no Master device is required to control communications
Connect up to 99 x WI-I/O-EX-1-S units as multi-drop Modbus I/O
(RS485 extenders/isolators required for more than 31 units per single multi-drop length)
RS485 multi-drop up to 2 km (1 mile) depending on installation environment
Three I/O versions available
WI-I/O-EX-1-S
Digital inputs
Digital outputs
67200005035
-11
up to 16
up to 16
67200005036
-12
up to 8
Voltage-free contacts
up to 8
67200005037
-13
up to 8
up to 8
FET
Analog inputs
0
4 “floating”/ 8 commoned
0
0-20mA / 0-10V
Analog outputs
Pulse inputs
Pulse outputs
0
0
4
1KHz
8
15Hz
0
8 sink / source
0-20mA / 0-10V
0
8
15Hz
8
15Hz
Note: Digital inputs and outputs are combined channels. When a channel is used as an output, it is not available as an input. Pulse and
digital I/O are same connection.
• Peer-to-peer communications; Exception reporting; Reliable self-checking messages;
Any input on any unit can be linked to any output on any unit. Inputs can be linked to multiple outputs;
Serial communications 9.6Kb/s
• Alternate Modbus RTU or Modbus ASCII slave protocol, serial communications configurable up to 115.2Kb/s,
7 or 8 data bit format
• External I/O plus internally calculated values - analog setpoint status, pulse rate and pulse total,
power supply voltage, power supply alarm
• Setpoint status generated by comparing analog inputs to high and low setpoints
• Analog inputs selectable as “floating” dual-terminal inputs or commoned single-terminal inputs;
Configurable current (0-10/0-20/4-20mA) or voltage (0-5/0-10/1-5V).
• Analog outputs selectable as single-terminal source or sink outputs. Configurable current (0-10/0-20/4-20mA)
or voltage (0-5/0-10/1-5V). Configurable scaling, zero and span parameters.
• Pulse inputs generate separate pulse count value and a pulse rate value. Pulse rates are treated as internal analog registers
with a configurable maximum value.
• Multiple communication-failure diagnostics with output status. Fail-to-transmit alarm and fail-to-receive alarm status.
• Class 1 Div 2 hazardous areas approval
• Input measurement display and output “forcing” diagnostics.
• Communication logging diagnostics.
• Easy-to-use E-Series Windows configuration.
10
900 MHz
E x p a n s i o n I / O U n i t s — P ro d u c t D a t a
WI-I/O-EX-1-S-11
WI-I/O-EX-1-S-12
up to 16 selectable I/O
up to 8 selectable I/O
Technical Data
Inputs:
Digital: suitable for voltage free contacts or NPN transistor,
contact wetting current 5mA, inputs are surge protected
Analog: “floating” differential inputs, common mode voltage
27V, 24VDC for powering external loops provided, 0-20mA/
0-10V resolution 12 bit, accuracy 0.1%
Pulse: specifications as per digital inputs Max pulse rate 1kHz,
pulse width min 0.5ms
Outputs
Digital: FET outputs, 30VDC 200mA
Pulse: specifications as per digital outputs
Max pulse rate 15.625Hz, pulse width min 32ms
8 input channels, selectable as 4 dual-terminal floating inputs
or 8 single-terminal commoned inputs.
4 inputs (DIO1-4)
up to 16 selectable I/O
8 outputs (DIO1-8)
up to 8 selectable I/O
8 outputs (DIO1-8)
24VDC, over-voltage and reverse power protected Internal
monitoring of supply voltage. This value may be transmitted
to remote modules for monitoring.
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
24VDC, over-voltage and reverse power protected Internal
monitoring of supply voltage. This value may be transmitted
to remote modules for monitoring.
An internal DC/DC converter provides 24VDC 150mA
for analog loop supply.
RS232
RS485
serial port configurable up to 115.2Kb/s, 7/8 data bits,
n/e/o parity, 1 / 2 stop bits
configurable as RS485 port
max cable distance 2000 m terminal connections
serial port configurable up to 115.2Kb/s, 7/8 data bits, n/e/o
parity, 1 / 2 stop bits
configurable as RS485 port
max cable distance 2000 m terminal connections
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
-40 to 60°C (-40 to 140°F)
0-99% RH
FCC Part 15, AS3548, 89/336/EEC
CSA Class 1 Div 2 hazardous areas (pending)
DIN rail mounting
power supply, processor OK, serial TX and RX, digital I/O
-40 to 60°C (-40 to 140°F)
0-99% RH
FCC Part 15, AS3548, 89/336/EEC
CSA Class 1 Div 2 hazardous areas (pending)
DIN rail mounting
power supply, processor OK, serial TX and RX, digital I/O
Dimensions mm (in)
150 x 180 x 35 (5.91 x 7.09 x 1.38)
150 x 180 x 35 (5.91 x 7.09 x 1.38)
Power Supply
Serial Port
RS485
Ordering Data
Type
WI-I/O-EX-1-S-11
Part No.
6720005035
Type
WI-I/O-EX-1-S-12
Part No.
6720005036
11
E x p a n s i o n I / O U n i t s — P ro d u c t D a t a
900 MHz
WI-I/O-EX-1-S-13
Technical Data
Inputs:
Digital: suitable for voltage free contacts or NPN transistor,
contact wetting current 5mA, inputs are surge protected
Outputs
Digital: FET outputs, 30VDC 200mA
Analog: selectable as current/voltage source or current sink
to common, max loop voltage 27V, max loop resistance
1000 ohms, 0 – 20mA/
0 – 10V, 12 bit, accuracy 0.1%
Pulse: specifications as per digital outputs
Max pulse rate 15.625Hz, pulse width min 32ms
Power Supply
Serial Port
RS485
up to 8 selectable I/O
up to 8 selectable I/O
8 channels
8 outputs (DIO1-8)
24VDC, over-voltage and reverse power protected Internal
monitoring of supply voltage. This value may be transmitted
to remote modules for monitoring.
An internal DC/DC converter provides 20VDC 150mA
for analog loop supply.
RS232
RS485
serial port configurable up to 115.2Kb/s, 7/8 data bits, n/e/o
parity, 1 / 2 stop bits
configuration port 9pin DB9 female connector, 9.6Kb/s, 8/n/1
max cable distance 2000 m terminal connections
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
-40 to 60°C (-40 to 140°F)
0-99% RH
FCC Part 15, AS3548, 89/336/EEC
CSA Class 1 Div 2 hazardous areas (pending)
DIN rail mounting
power supply, processor OK, serial TX and RX, digital I/O
Dimensions mm (in)
150 x 180 x 35 (5.91 x 7.09 x 1.38)
Ordering Data
12
Type
WI-I/O-EX-1-S-13
Part No.
6720005037
Tr a n s m i t t e r ( S i n g l e S e n s o r U n i t s ) — I n t ro d u c t i o n
WI-I/O 9-K Transmitter (Single Sensor Units)
• Frequency hopping spread spectrum 902-928 MHz 1W, license-free USA/Canada
• Configurable sub-bands license-free Mexico, South America, Australia/NZ, Hong Kong
The Single Sensor Wireless I/O range of products is suitable for connecting to a single sensor or group of sensors and provides an
economical solution for remote monitoring systems. Capable of being powered by battery-only supplies, these products are particularly suitable where power is not available.
Features
• Input-only unit - two digital/pulse one analog
• Networks with Multi-I/O and Gateway units
• Analog Loop Supply for field devices
• Sensor signals (inputs) are transmitted to a Multi-I/O module where the signals are re-created as output signals,
or passed via serial or Ethernet data bus to a host device such as a PLC or SCADA system.
• Extremely low power consumption by reverting to “sleep” mode
• Multiple power supply options including battery-only supply
• Weatherproof IP66 / NEMA 4 enclosures
• Class 1 Div 2 hazardous areas approval (USA/Canada)
• Up to 3000 wireless units per network
• Any input on any unit can be wirelessly linked to any output on any unit. Inputs can be linked to multiple outputs.
• Peer-to-peer communications. Exception reporting. Reliable self-checking messages. Highly secure data encryption.
• Multi-hop repeater functions - up to 5 intermediate units can be configured in any input-output link
• External inputs plus internally calculated values - analog setpoint status,
pulse rate and pulse total, power supply voltage, power supply alarm
• Setpoint status generated by comparing analog input to high and low setpoints.
• Pulse inputs generate separate pulse count value and a pulse rate value.
Pulse rates are treated as internal analog registers with a configurable maximum value.
• Power supply generates internal I/O values that can be transmitted–
low normal supply voltage status, low battery voltage status and battery voltage (analog)
• Can connect to up/down counter transducers such as shaft-encoders
• Easily configured to repeat the transmission several times to ensure that the transmission is received correctly
• Easy-to-use E-Series Windows configuration.
13
Tr a n s m i t t e r ( S i n g l e S e n s o r U n i t s ) — P ro d u c t D a t a
900 MHz
WI-I/O-9-K
Technical Data
Inputs:
Digital:
Pulse:
Up/Down Pulse Count
Pulse Rate
Analog:
two digital/pulse inputs, suitable for voltage free contacts / NPN, or voltage input 0-1 VDC on / >3 VDC off
status transmission on change of input signal and on time elapsed since last transmission - update time period 10 sec - 5days, a
separate update time can be configured when the discrete input is “on”
Pulse rate up to 1000 Hz, 3 msec on time. Pulse counted as 16 bit register with a 16 bit overflow register (total count 32 bit).
Transmissions occur when count change exceeds configured increase, or on time elapsed since last transmission; update
time 10 sec - 5 days ; change transmissions may be suspended if increase exceeds a configured value to reduce radio traffic.
the two pulse inputs may be configured to a single count, to suit quadrature or incremental shaft encoder transducers.
calculated from rate of pulse input and treated as an internal analog input. Configurable scaling. Transmitted as per analog input.
one analog input 0-25 mA (4-20mA, 0-10mA)
0-10V also available “floating” differential input
resolution
accuracy
sample time configurable
transducer warm-up time configurable
analog value transmitted on change of input signal or time
elapsed since last transmission,
change sensitivity configurable
update time configurable
12 bit
< 0.1 % measurement continuous or sampled
1 min - 5 days
0.5-127 sec
Setpoint Status
high and low setpoints generate internal digital status
setpoint status sets (on) when analog value < low setpoint and resets (off) when analog value > high setpoint
status transmitted as per digital input
Power Supply
Power consumption @12VDC
Power consumption during radio transmission (50 - 100 msec)
Analog loop supply internally generated
Internal monitoring of supply low voltage status
Power consumption increases for pulse inputs > 10Hz.
Serial Port
RS232
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
frequency hopping spread spectrum
Transmit power
Maximum line of sight range
Receiver data sensitivity
Data rate
Antenna connector
Dimensions mm (in)
Ordering Data
Battery Pack (optional)
Plug and Lead-1 meter
14
0.7-75%
0.1min - 5 days
quiescent (sleep mode) 120µA, operating mode 10mA + analog loop
300mA @ 1W, 220µA @ 500mW
100mA @ 100mW, 50mA @ 10mW
Yes
may be transmitted to remote modules as an “input”
DB9 female DCE, used for configuration and diagnostics
-40 to 60°C (-40 to 140°F)
0 - 99% RH
compliant 89/336 EEC, EN 300 683, AS3548, FCC Part 15
Housing - IP66 NEMA4; FCC Part 15.247, RS210, CSA Class 1, Div 2
Radio TX, Operation OK
902-928MHz, sub-bands available
1W
20miles (4W ERP), 15 km (1W ERP)
108 dBm
19.2 Kbs with forward error correction
SMA coaxial
150 x 64 x 36 (5.1 x 2.5 x 1.4)
Type
WI-I/O-9-K
WI-BP-I/O-9-K
WI-PLI-9-K
Part No.
6720005004
6720005112
6720005113
W i re l e s s G a t e w a y s — I n t ro d u c t i o n
Wireless Gateways WI-GTWY-9
• Frequency hopping spread spectrum
• 902-928 MHz 1W license-free USA/Canada
• Configurable sub-bands license-free Mexico, South America, Australia/NZ, Hong Kong
Features
• Connects to data bus at full bus speed (e.g. 12Mb/s for Profibus, 100Mb/s for Ethernet)
• Provides Protocol Conversion (Profibus, Modbus, Ethernet, DeviceNet)
• Can interconnect master-slave, slave-slave and master-master
• Interconnects different data buses - wireless protocol conversion
• Provides a peer-to-peer wireless network using WIB-net
• High security data encryption
• Automatic acknowledgment and error-correction
• Multiple path routing
• Eight on-board discrete I/O, individually configurable as input or output
• Network configuration is performed with easy-to-use free software
• Wide range power supply with integral back-up battery-charging feature
15
W i re l e s s G a t e w a y s — P ro d u c t D a t a
900 MHz
WI-GTWY-9-MD1
Modbus (Master & Slave), DF1
WI-GTWY-9-PR1
Profibus DP Slave
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
4300 I/O points (analog plus discrete)
16 bit
500
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
416 I/O bytes up to 1952 DI/1952 DO, or up to122 AI/122 AO
16 bit
500
-40 to 60°C (-40 to 140°F)
0 to 60°C (30 to 140°F)
0 - 99 %RH
EN 301 489, FCC Part 15,
Approved to FCC Part 15.247, RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX,
active status
0 - 95 %RH
EN 301 489, FCC Part 15, Approved to FCC Part 15.247,
RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX, active
status
Dimensions mm (in)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
Wireless Communications
Modbus RTU (binary), master / slave configurable. RS232 or
RS485, 300 - 19200 bits/sec.
Profibus-DP functionality according to EN 50170.
Modbus RTU
Allen-Bradley DF1 full-duplex. RS232 only, 300 - 19200
bits/sec.
RS-485 optically isolated with on-board DC/DC converter,
automatic baudrate detection (9600 bit/s - 12 Mbit/s)
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
Radio communications can be configured for combination
of event reporting (change-of-value), update time, read/write
blocks and poll response. Radio message includes system
addressing, unit addressing, error checking and configurable
security encryption.Communication control includes message
acknowledgments and up to four re-transmissions. Peer to
peer addressing. Messages may be routed through four
intermediate repeater addresses. Fail-to-transmit and fail-toreceive alarms configurable
Technical Data
Power Supply
Current drain during radio transmission
I/O Capacity
Register Size
Number of remote WI-GTWY-9 addresses
General Data
Operating Temperature
Storage Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
On-board I/O
Configuration
Diagnostics
Radio Transceiver
Frequency hopping spread spectrum
Transmit power
Receiver data sensitivity
Maximum line-of-sight range
Data rate
Antenna connector
Ordering Data
16
Type
WI-GTWY-9-MD1
Part No.
6720005020
Type
WI-GTWY-9-PR1
Part No.
6720005021
900 MHz
W i re l e s s G a t e w a y s — P ro d u c t D a t a
WI-GTWY-9-PR2
Profibus DP Master
WI-GTWY-9-ET1
Ethernet IP, Modbus TCP, TCP/IP functions
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
2048 bytes input and 2048 bytes output up to 4300 discrete
I/O points, or up to 1024 analog in / 1024 analog out
16 bit
500
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
2048 bytes input and 2048 bytes output up to 4300 discrete
I/O points, or up to 1024 analog in / 1024 analog out
16 bit
500
0 to 60°C (30 to 140°F)
0 to 60°C (30 to 140°F)
0 - 95 %RH
EN 301 489, FCC Part 15, Approved to FCC Part 15.247,
RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX,
active status
0 - 95 %RH
EN 301 489, FCC Part 15, Approved to FCC Part 15.247,
RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX,
active status
Dimensions mm (in)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
Wireless Communications
Profibus-DP functionality according to EN 50170.
RS-485 optically isolated with on-board DC/DC converter,
automatic baudrate detection (9600 bit/s - 12 Mbit/s)
10/100 Mbit/s, RJ45 connector, Transformer isolated interface
Modbus/TCP class 0, class 1 and partially class 2 slave
EtherNet/IP level 2 I/O Server
Embedded Web system (Dynamic HTTP), on-board file system
(1.4MB flash disc), user downloadable web pages through FTP
server, Email functionality (SMTP)
On-board I/O
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
Radio communications can be configured for combination
of event reporting (change-of-value), update time, read/write
blocks and poll response. Radio message includes system
addressing, unit addressing, error checking and configurable
security encryption.Communication control includes message
acknowledgments and up to four re-transmissions. Peer to
peer addressing. Messages may be routed through four
intermediate repeater addresses. Fail-to-transmit and fail-toreceive alarms configurable
Technical Data
Power Supply
Current drain during radio transmission
I/O Capacity
Register Size
Number of remote WI-GTWY-9 addresses
General Data
Operating Temperature
Storage Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
Configuration
Diagnostics
Radio Transceiver
Frequency hopping spread spectrum
Transmit power
Receiver data sensitivity
Maximum line-of-sight range
Data rate
Antenna connector
Ordering Data
Type
WI-GTWY-9-PR2
Part No.
6720005022
Type
WI-GTWY-9-ET1
Part No.
6720005023
17
W i re l e s s G a t e w a y s — P ro d u c t D a t a
900 MHz
WI-GTWY-9-DE1
DeviceNet Slave
WI-GTWY-9-M+1
Modbus Plus Slave
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
512 bytes input and 512 bytes output up to 4300 discrete I/O
points, or up to 256 analog in / 256 analog out
16 bit
500
9 - 30VDC / 12 - 24VAC
Battery charging circuit included for 12V back-up battery, max
charge current regulated to 0.7A (>12V supply)
Normal current drain
MD1 version 12V 150mA; 24V 90mA
Other version 12V 270mA; 24V 170mA
Add 5mA per active I/O
Add 12V 350mA; 24V 200mA to above
2048 bytes input and 2048 bytes output up to 4300 discrete
I/O points, or up to 1024 analog in / 1024 analog out
16 bit
500
0 to 60°C (30 to 140°F)
0 to 60°C (30 to 140°F)
0 - 95 %RH
EN 301 489, FCC Part 15, Approved to FCC Part 15.247,
RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX,
active status
0 - 95 %RH
EN 301 489, FCC Part 15, Approved to FCC Part 15.247,
RS210
Class 1 Div 2 (USA, Canada).
DIN rail mounting,
for processor OK, radio TX and RX, serial TX and RX,
active status
Dimensions mm (in)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
130 x 185 x 60 (5.1 x 7.3 x 2.4)
Wireless Communications
DeviceNet 2.0 Slave, optically isolated RS422 with selectable
baudrate between 125, 250 and 500 Kbit/sec.
Modbus RTU (binary), master / slave configurable. RS232 or
RS485, 300 - 19200 bits/sec.
Modbus Plus Slave, optically isolated RS485 with standard
baudrate of 1 Mbit/sec, global data base transactions with
routing for up to six networks.
On-board I/O
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
Eight discrete I/O, individually configurable as input or output.
Inputs suitable for voltage free contacts.
Outputs are FET, 30VDC 500mA.
via free Windows software
on-line read/write of I/O registers, radio signal strength values
from remote units, and off-line testing of data bus protocol.
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
902-908 MHz, sub-bands configurable
1W
108dBm
USA/Canada, 4W ERP, 20+ miles
19.2 Kb/s with forward-error correction
SMA coaxial
Radio communications can be configured for combination
of event reporting (change-of-value), update time, read/write
blocks and poll response. Radio message includes system
addressing, unit addressing, error checking and configurable
security encryption.Communication control includes message
acknowledgments and up to four re-transmissions. Peer to
peer addressing. Messages may be routed through four
intermediate repeater addresses. Fail-to-transmit and fail-toreceive alarms configurable
Technical Data
Power Supply
Current drain during radio transmission
I/O Capacity
Register Size
Number of remote WI-GTWY-9 addresses
General Data
Operating Temperature
Storage Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
frequency hopping spread spectrum
Transmit power
Maximum line of sight range
Configuration
Diagnostics
Radio Transceiver
Frequency hopping spread spectrum
Transmit power
Receiver data sensitivity
Maximum line-of-sight range
Data rate
Antenna connector
Ordering Data
18
Type
WI-GTWY-9-DE1
Part No.
6720005024
Type
WI-GTWY-9-M+1
Part No.
6720005025
W i re l e s s D a t a M o d e m s — I n t ro d u c t i o n
Wireless Data Modems
WI-MOD-E WIRELESS ETHERNET MODEM
Wireless data modems connect to serial or Ethernet links and
transmit the data wirelessly. The modem controls the wireless
messages and data ports to provide a “transparent” data transfer.
Features
Wireless Serial Data (Radio Modems)
• RS 232 and RS485 connections
• Industrial power supplies, industrial temperature rating
• Uses Global 2.4GHz ISM band
• 10/100 BaseT Ethernet, wireless data up to 11 Mbits/sec.
• 802.11b compliant 2.4GHz DSSS, 100mW or 300mW
• Typical line-of-sight distance 5 miles North America (4W
ERP)
• Configurable as Access Point / Client; Bridge / Router
WI-MOD-9-D RADIO MODEM (SERIAL DATA)
• License-free operation in North and South America
• Wireless data up to 115.2 Kb/s
• 902-928 MHz, 1W, frequency hopping spread spectrum
• Security, reliability, redundancy …
• High RF output and superior receiver sensitivity gives excellent penetration in congested industrial environments
• Multiple layers of error-detection and correction
• Typical line-of-sight distance 20 miles North America (4W ERP)
• Automatic changeover to another Access Point
if the wireless link fails
• One serial data port—
RS232 and RS485 connections provided
• Military-grade AES security encryption of wireless data
• Serial data up to 115.2Kb/s
• Configuration by Hayes AT commands
or Windows Configuration software
• Industrial ratings down to –35°C
• Firewall protection and efficient wireless management …
• Message filtering at MAC address level
Modes of Operation
• Two serial interfaces, RS232 and RS485
Transparent mode broadcast, “multi-drop” operation configurable
error-checking, unlimited repeaters (store & forward).
• Serial connectivity + Ethernet connectivity at the same time
Controlled mode addressable point-to-point operation,
authentication and automatic re-tries, addressed
repeater routing.
• Serial Modbus to Modbus TCP conversion
WI-MOD-9-E WIRELESS ETHERNET MODEM
Features
The WI-MOD-9-E is an ideal solution for Ethernet connections
in process control and automation applications - PLCs, DCS,
SCADA, data acquisition … it can handle multiple applications
simultaneously.
• 10/100 BaseT Ethernet, wireless data up to 200 Kbits/sec.
• 902-928 MHz, 0.1 - 1W, frequency hopping
spread spectrum
• Typical line-of-sight distance 20 miles (4W ERP),
up to 60 miles using high gain antennas (4W ERP
• Configurable as Access Point / Client; Bridge / Router
• Multiple layers of error-detection and correction
• Military-grade AES security encryption of wireless data
• PPP and serial server functionality
• Discrete channel for status I/O, for failure status
or external status transfer.
• Easy to use configuration and Powerful diagnostics …
• Configuration and diagnostics via web-browser
• Remote configuration and diagnostics via the wireless link
IE-GPRS-I/O-NA GPRS Alarm Modem
Features
• Signalling and telecontrol system designed for automatic
operation if required
• Dual band GSM/GPRS modem (GSM 900/1800MHz,
950/1900MHz)
• Permanently online
• Low-cost M2M rates
• 8 digital and 4 analog input ports, 4 digital output ports
• Message filtering at MAC address level
• Immediate alarm signalling via SMS, FAX, e-mail or voice
message in the event of limiting values being exceeded at
the input ports
• Two serial interfaces, RS232 and RS485
• Alarm via RS232 also possible
• Serial connectivity + Ethernet connectivity at the same time
• 8-level recipient list with very flexible configuration options
• PPP and serial server functionality
• Integration of port statuses in message
• Serial Modbus to Modbus TCP conversion
• Integral cost monitoring
• Discrete channel for status I/O, for failure status or external
status transfer.
• Data logger (LAN and Internet) available
• Firewall protection and efficient wireless management …
• Easy to use configuration and Powerful diagnostics
• Configuration and diagnostics via web-browser
• Remote configuration and diagnostics via the wireless link
19
W i re l e s s D a t a M o d e m s — P ro d u c t D a t a
900 MHz
WI-MOD-9-D
Radio 900MHz
Technical Data
Power Supply
Normal current drain
Current when transmitting
Low power mode current drain
Serial Port
Standard data rates
RS232 and RS485
Characters supported
RS232 Connection
RS485 connection
Input and output buffers
General Data
Operating Temperature
Humidity
EMC Standards
Approvals
Mounting
LED indication
10 - 30 VDC or 10 - 24 VAC
70mA/12VDC or 50mA/24VDC
350mA/12V or 250mA/ 24V
20mA/12VDC or 15mA/24VDC
1200 to 115200 baud.
standard interface connections provided, each connected to
the same serial port. Serial interfaces are asynchronous
non-return-zero (NRZ) format
7 or 8 data bits, even/odd/no parity, 1 or 2 stop bits
provides full duplex operation as a DCE device with RTS/CTS
hardware handshaking- standard D9 connector
provides half duplex operation for twisted pair multi-drop networks
2Kbyte
-40 to 70°C (-40 to +140°F)
FCC Part 15 Class A and FCC Part 15.247
CSA Class 1, Div 2
DIN rail mounting
for unit OK, radio TX and RX, serial TX and RX, DCD (comms OK)
Dimensions mm (in)
115 x 165 x 32 (4.5 x 6.5 x 1.3)
Radio Transceiver
Frequency - USA/Canada
Hop Sequence
Transmit Power
Expected line-of-sight range, depending on local conditions
RF Data Transmission Rate
Range may be extended by:
Frequency Hopping Spread Spectrum Transceiver
902 - 928 MHz
16 x 50
1W
USA/Canada 20+ miles
19200 baud, 57600 baud, 115200 baud (selectable)
up to five intermediate repeaters in controlled mode
unlimited repeaters in transparent mode
SMA coaxial
Antenna connection
Data Transmission
Transparent mode:
Controlled mode:
Configuration
Diagnostics
Ordering Data
20
Data is transmitted with a system and group address.
Data transmission begins as serial data is received—maximum
packet size is 530 bytes. All modules with the 0correct system
address, which receive the data packets, outputs the
data—error checking is optional.
Data is transmitted in packets with a system address, source
address, destination address, up to five intermediate repeater
addresses, and a 16 bit CRC error-check. If the packet is
received with a correct error check, only the destination module
will output the data and will also return an ACK transmission.
If the source module does not receive the ACK, it will retry
a further four times. DCD provides communications status.
Auto-connect and dial-up-control modes are available.
CTS/RTS flow control provided based on input
buffer availability.
freeware software package or by Hayes AT commands
Radio noise, signal strength and bit error rate (BER)
diagnostics included. Radio signal strength value available
on-line to host device.
Type
WI-MOD-9-D
Part No.
6720005050
900 MHz
W i re l e s s D a t a M o d e m s — P ro d u c t D a t a
WI-MOD-9-E
Ethernet 900MHz
Technical Data
Description: Ethernet
10/100 BaseT RJ45, IEEE 802.3 compliant.
Bridge/router functions work with all Ethernet protocols
Embedded Protocols:
TCP/IP, UDP ARP, PPP, ICMP, HTTP, FTP, TFTP, TELNET
Serial
RS232 V.24 DCE
RS485
1.2 to 115.2 Kb/s
1.2 to 115.2 Kb/s
Serial server, PPP, Modbus to Modbus TCP conversion
Discrete I/O
Input
Output
One I/O channel
Voltage-free contact
FET 30VDC 500mA
Networking
Configurable as Access Point or Client, Bridge or Router
Point-to-point, Point-to-multipoint,
user configurable addressing
Repeater functionality
MAC Filtering - whitelist or blacklist
General Data
Operating Temperature
Humidity
Power Supply
Current Normal
Transmit
Approvals
Mounting
LED indication
-40 to 60°C (-40 to 140°F)
99% non-condensing
10 – 30VDC
280mA (12V), 150mA (24V)
(1W) 500mA (12V), 300mA (24V)
FCC 15.247, RS210,
Hazardous area CSA Class 1 Div 2
DIN rail mounting
Power/OK, Radio Rx and Tx, Radio Link, LAN Link/Activity,
Serial Activity, Digital I/O, LAN 10/100Mbit Link
Dimensions mm (in)
Weight
115 x 141 x 32 (4.5 x 5.55 x 1.4)
< 0.4 kg / 0.8 lb
Radio Transceiver
Frequency - USA/Canada
Hop Sequence
Transmit Power
Receiver sensitivity
Data rates
Protocol
Radio range
Frequency Hopping Spread Spectrum
902 - 928 MHz
16 x 50
0.1 – 1W (20 – 30 dBm) configurable
108 dBm @ 10-6 BER
19.2, 57.6, 115.2, 230 Kb/s or auto rate selection
CSMA/CA with 32 bit CRC and auto-correction
up to 60 miles / 100 km line-of-sight using high gain antennas
(*up to 4W ERP permitted in USA/Canada)
Range may be extended using repeater features
Antenna connection
SMA coaxial
Security
128 bit AES encryption or
64 bit proprietary encryption (configurable)
MAC filtering
Password protected configuration
HTTP with remote configuration via wireless link
RSSI, channel noise, BER, connection monitoring and statistics
Configuration
Diagnostics
Ordering Data
Type
WI-MOD-9-E
Part No.
6720005051
21
W i re l e s s D a t a M o d e m s — P ro d u c t D a t a
2.4 GHz
WI-MOD-E-100
Ethernet 2.4GHz 100mW
WI-MOD-E-300
Ethernet 2.4GHz 300mW
Description: Ethernet
10/100 BaseT RJ45, IEEE 802.3
Bridge/router functions work with all Ethernet protocols
10/100 BaseT RJ45, IEEE 802.3
Bridge/router functions work with all Ethernet protocols
Embedded Protocols:
TCP/IP, UDP ARP, PPP, ICMP, HTTP, FTP, TFTP, TELNET
TCP/IP, UDP ARP, PPP, ICMP, HTTP, FTP, TFTP, TELNET
1.2 to 115.2 Kb/s
1.2 to 115.2 Kb/s
Serial server, PPP, Modbus to Modbus TCP conversion
1.2 to 115.2 Kb/s
1.2 to 115.2 Kb/s
Serial server, PPP, Modbus to Modbus TCP conversion
Discrete I/O
Input
Output
One I/O channel
voltage-free contact
FET 30VDC 500mA
One I/O channel
voltage-free contact
FET 30VDC 500mA
Networking
Configurable as Access Point or Client, Bridge or Router
Point-to-Point, Point-to-Multipoint,
user configurable addressing
Repeater functionality
MAC Filtering – whitelist or blacklist.
Serial gateway TELNET
Configurable as Access Point or Client, Bridge or Router
Point-to-Point, Point-to-Multipoint,
user configurable addressing
Repeater functionality
MAC Filtering – whitelist or blacklist.
Serial gateway TELNET
-35 to 65°C (-30 to 150°F)
99% non-condensing
9 – 30VDC, Current 240mA (12VDC), 150mA (24VDC)
-35 to 65°C (-30 to 150°F)
99% non-condensing
9 – 30VDC, Current 240mA (12VDC), 150mA (24VDC)
FCC Part 15.247, CE ETS 300 328, RSS 210, Hazardous area
CSA Class 1 Div 2, IEC 60950
DIN rail mounting
Power / OK, Radio Rx and Tx, Radio Link, LAN link / Activity ,
Serial Activity, Digital I/O
115 x 141 x 32 (4.5 x 5.6 x 1.4)
< 0.4 kg / 0.8 lb
FCC Part 15.247, CE ETS 300 328, RSS 210, Hazardous area
CSA Class 1 Div 2, IEC 60950
DIN rail mounting
Power / OK, Radio Rx and Tx, Radio Link, LAN link / Activity ,
Serial Activity, Digital I/O
115 x 141 x 32 (4.5 x 5.6 x 1.4)
< 0.4 kg / 0.8 lb
2.400 – 2.484GHz Direct Sequence Spread Spectrum (DSSS),
13 selectable zones
802.11b compliant, auto rate selection 1 Mb, 2Mb, 5.5Mb, 11Mb
2.400 – 2.484GHz Direct Sequence Spread Spectrum (DSSS),
13 selectable zones
802.11b compliant, auto rate selection 1 Mb, 2Mb, 5.5Mb, 11Mb
100mW (20dBm), dependent on local regulations
96dBm @ 1MB/s, -91dBm @ 11Mb/s < 8% FER
1km @ 100mW
Range may be extended using repeater features
Dual SMA coaxial
300mW (25dBm), dependent on local regulations
96dBm @ 1MB/s, -91dBm @ 11Mb/s < 8% FER
3 miles @ 300mW
Range may be extended using repeater features
Dual SMA coaxial
128 bit AES encryption (WPA2), TKIP (WPA1) or +04 bit / 40 bit
WEP
MAC Address filtering
Password protected configuration
HTTP with remote configuration via wireless link
Web based system management - RF signal strength, Bit Error
Rate, connection monitoring and statistics
PPP Protocol Access to diagnostics
Firmware upgradeable via serial port
128 bit AES encryption (WPA2), TKIP (WPA1) or +04 bit / 40 bit
WEP
MAC Address filtering
Password protected configuration
HTTP with remote configuration via wireless link
Web based system management - RF signal strength, Bit Error
Rate, connection monitoring and statistics
PPP Protocol Access to diagnostics
Firmware upgradeable via serial port
Type
WI-MOD-E-100
Type
WI-MOD-E-300
Technical Data
Serial
RS232 V.24 DCE
RS485
General Data
Operating Temperature
Humidity
Power Supply
Current Normal
Transmit
Approvals
Mounting
LED indication
Dimensions mm (in)
Weight
Wireless
Radio Transceiver
Transmit Power
Receiver sensitivity
Radio range
Antenna connection
Security
Configuration
Diagnostics
Ordering Data
22
Part No.
6720005052
Part No.
6720005053
GPRS/GSM
W i re l e s s D a t a M o d e m s — P ro d u c t D a t a
GPRS Alarm Modem
GPRS Alarm Modem
The GPRS Alarm Modem is designed to
collect messages that are detected as
activated switching contacts and analog
limit values. Communication with the server
is performed over a virtual dedicated line
via GPRS as a point-to-point, multipoint
or multi-drop connection. An Internet
exchange server may log the states of
the inputs and outputs permanently on
the basis of event or time control. The
server constitutes a relational database,
i.e. external access is possible via SQL
queries.
The exchange server is a service provided by Weidmuller.
The configurable alarms are issued via
SMS, e-mail, voice messaging and/or fax.
The IE-GPRS-I/O implements telecontrol
by remote-switching of the outputs via
telephone/mobile telephone.
The IE-GPRS-I/O can be teleserviced and
remote-configured.
The Weidmuller GPRS I/O has an aluminum
housing just 45 mm wide and the following configurable features:
• Signaling and telecontrol system
designed for automatic operation if
required
Technical Data
Housing
Ports
AC input voltage, min.-max.
DC input voltage, min.-max.
Input power AC/DC
Input frequency
Operating temperature
Storage temperature
Installation
Ingress protection class
Data rate
Functionality
Status indication
Approvals
Transmission rate
Aluminum
8 digital inputs; 4 digital outputs;
4 analog inputs; 1xRS232 interface
8-24VAC
10-36VDC
max. 5 VA AC / max. 5 W DC
47-63 Hz
-10 to 55°C (14 to 131°F)
-10 to 70°C (14 to 158°F)
TS35 DIN-Rail or Wall Mounted
IP 20
max. 53.6 kbps
SMTP; POP3; FTP; DNS; IPTCP; UDP sockets
Power
cULus, CE
GPRS dependent
Dimensions mm (in)
137 x 45 x 155 (5.4 x 1.8 x 6.1)
Ordering Data
950/1900 MHz
Type
IE-GPRS-I/O-NA
Part No.
8903980000
• Dual band GSM/GPRS modem (GSM
900/1800MHz, 950/1900MHz)
• Permanently online
• Low-cost M2M rates
• 8 digital and 4 analog input ports, 4
digital output ports
• Immediate alarm signaling via SMS,
FAX, e-mail or voice message in the
event of limiting values being exceeded at the input ports
• Alarm via RS232 also possible
• 8-level recipient list with very flexible
configuration options
• Integration of port statuses in
message
• Integral cost monitoring
• Data logger (LAN and Internet)
available
23
Accessories
869/900 MHz ANTENNAS
-2dB Whip Antenna WI-ANT-DEMO-900
The WI-ANT-DEMO-900 is a quarter-wave whip antenna. It can be used for short
distance applications, where the wireless unit and antenna are mounted inside a
non-metallic enclosure.
As the whip antenna is “ground-dependent”, the gain and distance depends on the
installation environment.
Type
WI-ANT-DEMO-900
Part No.
6720005089
WI-ANT-DEMO-900
Whip Antenna
-2dB Whip Antenna WI-ANT-DPL-2-6-54
The WI-ANT-DPL-2-6-54 whip antennas are suitable for the 900MHz products. These
antennas have less gain than the WI-ANT-DPL-0-16 however are smaller and are
preferred where space is tight.
The WI-ANT-DPL-2-6-54 is fitted with approximately 16 feet / 5 meters RG8 coaxial
cable and SMA male connector. Further coaxial extensions are not recommended with
this antenna.
The WI-ANT-DPL-2-6-54 is mounted from the base through a 3/8" (10mm) hole. This
compact antenna is designed for short range use only.
The antenna is suitable for internal or external mounting. This antenna may be used
on vehicles with a suitable bracket not supplied or when mounted in the panel work.
Type
WI-ANT-DPL-2-6-54
WI-ANT-DPL-2-6-54
Whip Antenna
Part No.
6720005086
0dB Dipole Antenna WI-ANT-DPL-0-16
The WI-ANT-DPL-0-16 is a ground independent half wave dipole suitable for the
900MHz products. It is a slimline, lightweight antenna that is easily mounted - this
antenna is the most common antenna used in applications within industrial plants or
factories.
The antenna has 15 feet / 5 meters of RG58 Cellfoil coaxial cable already terminated
with a crimped SMA male connector. This antenna should not be used with additional
lengths of coaxial cable - where longer lengths are required, used the WI-ANT-CLR900-5-32 antenna or higher gain antenna. This compact antenna is made for vertical
mounting. Correctly installed, this antenna will provide a net unity gain after allowing for
the loss of the attached coaxial cable. The pack includes a standard pole bracket and
clamps made from grade 304 stainless steel.
Type
WI-ANT-DPL-0-16
Part No.
6720005080
5dB Collinear Antenna WI-ANT-CLR-900-5-32
The WI-ANT-CLR-900-5-32 collinear antenna may be used for external or internal
mounting. The WI-ANT-CLR-900-5-32 is a slimline, lightweight antenna that is easily
mounted. A short RG58 coaxial tail is terminated with a crimped N-Type female connector. This compact antenna is made for vertical mounting clear from obstructions.
The pack includes a standard pole bracket made from grade 304 stainless steel
(included with the antenna).
Type
WI-ANT-CLR-900-5-32
WI-ANT-DPL-0-16
Dipole Antenna
WI-ANT-CLR-900-5-32
5dB Collinear Antenna
Part No.
6720005081
8dB Collinear Antenna WI-ANT-CLR-900-8-54
The WI-ANT-CLR-900-8-54 collinear antenna is a slimline, lightweight antenna which is
easily mounted, with a N-Type female connector. The WI-ANT-CLR-900-8-54 antenna
is mounted at the base tube by U bracket (WI-BR-CLR-KIT). This antenna is used
when maximum range is required or as a base station antenna.
Type
WI-ANT-CLR-900-8-54
24
Part No.
6720005082
WI-ANT-CLR-900-8-54
8dB Collinear Antenna
Accessories
869/900 MHz ANTENNAS (continued)
9dB 6 and 15dB 15 element Yagi Antenna WI-ANT-YGI-10-6, WI-ANT-YGI-15-16
The WI-ANT-YGI-10-6 6 element and WI-ANT-YGI-15-16 15 element Yagi
antennas are made for use with the WI-I/O-9 series telemetry products.
They are designed for pole mount and to be clear from obstructions. The narrow
beamwidth and high front to back ratio is effective in reducing the affects of interference
and extending radio range. Mounting brackets are supplied separately with these antennas.
A standard female N-Type connection from a 6"/150 mm tail provides a simple
connection method when using the WI-BR-YAGI-KIT.
Type
WI-ANT-YGI-10-6
WI-ANT-YGI-15-16
Part No.
6720005084
6720005085
WI-ANT-YGI-10-6,
WI-ANT-YGI-15-16
Yagi Antenna
2.4 GHz ANTENNAS
0dB Whip Antenna WI-ANT-DEMO-2400
The WI-ANT-DEMO-2400 is a quarter-wave whip antenna. It can be used for short
distance applications, where the wireless unit and antenna are mounted inside a
non-metallic enclosure.
As the whip antenna is “ground-dependent”, the gain and distance depends on the
installation environment.
Type
WI-ANT-DEMO-2400
Part No.
6720005099
WI-ANT-DEMO-2400
Whip Antenna
3dB Collinear Antenna WI-ANT-DPL-0-9
The WI-ANT-DPL-0-9 is a ground independent collinear antenna that may be used
for external or internal mounting.
The WI-ANT-DPL-0-9 is a slimline, lightweight antenna that is easily mounted.
Approximately 15 feet (5m) of low loss RG58 coaxial cable is terminated with a
male SMA connector. This compact antenna is made for vertical mounting clear
from obstructions.
Correctly installed this antenna will provide unity gain with the attached coaxial cable. The
pack includes a standard pole bracket and clamps made from grade 304 stainless steel.
Type
WI-ANT-DPL-0-9
Part No.
6720005090
WI-ANT-DPL-0-9
3dB Collinear Antenna
5dB Collinear Antenna WI-ANT-CLR-5-20
The WI-ANT-CLR-5-20 collinear antenna may be used for external or internal mounting.
The WI-ANT-CLR-5-20 is a slimline, lightweight antenna that is easily mounted. A short
RG58 coaxial tail is terminated with a crimped N-Type female connector. This compact
antenna is made for vertical mounting clear from obstructions.
The pack includes a standard pole bracket made from grade 304 stainless steel. At data
link 2.4 GHz frequencies, it is important to keep cable runs to the shortest length possible.
Type
WI-ANT-CLR-5-20
Part No.
6720005091
WI-ANT-CLR-5-20
5dB Collinear Antenna
10dB Collinear Antenna WI-ANT-CLR-8-34
The WI-ANT-CLR-8-34 is a vertically polarized collinear gain antenna designed for communications in the base and mobile ISM 2.4 GHz data link band.
Construction consists of copper internals and a black fiberglass radome. An N-Type Female
connector is built into the high quality stainless steel mount tube.
Black Radome is provided to improve the antennas resistance to ice build up. This sturdy
and compact design allows the antenna to be conveniently mounted on a mast, building or
vehicle. The pack includes a standard 304 stainless steel pole clamp.
Type
WI-ANT-CLR-8-34
Part No.
6720005092
WI-ANT-CLR-8-34
10dB Collinear Antenna
25
Accessories
2.4 GHz ANTENNAS (continued)
18dB Element Yagi Antenna WI-ANT-YGI-18
The 18 element Yagi antenna is designed for pole mount and to be clear from obstructions.
Black Radome is provided to improve the antennas resistance to ice build up.The narrow beam width and high front to back ratio is and extending radio range. A standard
female N-Type connection from a 150mm tail provides a simple connection method
when using the WI-CCSMA-N-33. Mounting brackets are supplied with this antenna.
Type
WI-ANT-YGI-18
WI-ANT-YGI-18
18 Element Yagi Antenna
Part No.
6720005093
COAXIAL CABLE KITS AND ACCESSORIES
Coaxial Lead WI-CCTAIL-SMA-24
The WI-CCTAIL-SMA-24 is a 600mm (24 inch) RG58 coaxial lead. This flexible coaxial
“tail” is used inside enclosures to link large diameter coaxial cables (such as RG213 or
LDF4) to the wireless units.
The WI-CCTAIL-SMA-24 is terminated with a flanged N-Type (female) bulkhead connector at one end and an SMA connector at the other end.
Type
WI-CCTAIL-SMA-24
Loss @ 900MHz
0.8dB
Loss @ 2.4 GHz
1.2dB
Part No.
6720005103
WI-CCTAIL-SMA-24
Coaxial Lead
Coaxial Cable Kits WI-CCSMA-N-10, WI-CCSMA-N-33, WI-CCSMA-N-66
The WI-CCSMA-N-10, WI-CCSMA-N-33 and WI-CCSMA-N-66 coaxial cable kits are
designed for use between wireless units and external mounted antennas. The coaxial
cable is terminated and tested alleviating time-consuming field termination work.
The WI-CCSMA-N-10 is 3.05 meters (10 feet) long, WI-CCSMA-N-33 is 10 meters
(33 feet) long and the WI-CCSMA-N-66 is 20 meters (66 feet) long.
The kits are terminated with a N-type male connector at the antenna end of the cable.
For the wireless end, kits are available with either SMA or BNC connectors to suit
different products.
Type
WI-CCSMA-N-10
WI-CCSMA-N-33
WI-CCSMA-N-66
Loss @ 900MHz
1.0dB
3.2dB
6.2dB
Loss @ 2.4 GHz
2.0dB
5.9dB
11.4dB
Part No.
6720005100
6720005101
6720005102
WI-CCSMA-N-10, WI-CCSMA-N-33,
WI-CCSMA-N-66
Coaxial Cable Kits
Low Loss Coaxial Cables
For cables longer than a WI-CCSMA-N-66 kit (or WI-CCSMA-N-33 for 2.4GHz), low loss
coaxial cables such as LDF4 should be used. Low loss cables have large diameters with
large bending radii and are not suitable for direct connection to wireless modules.
Experience is required to terminate this type of cable and the coaxial manufacturer is
able to assist. Consider using Andrew LDF4-250 1/2 inch - www.andrew.com
Connecting Cables for “L” Series
The WI-CSER-RJ45 cable is used to connect and perform diagnostic and configuration
with the unidirectional Transmitter/Receiver units including the WI-I/O-L-T and WI-I/O-L-R.
This high quality cable is fitted with a molded DB9 on one end and an RJ45 connector
on the other.
Type
WI-CSER-RJ45
WI-CSER-RJ45
Connecting Cables for “L” Series
Part No.
6720005108
Serial to Serial Connectivity Cables
The WI-CSER-905-9 Serial cable is used for all Weidmuller telemetry products, allowing
connection to your computer or laptop’s RS232 port, for diagnostic and configuration.
This high quality cable is fitted with a molded DB9 male and DB9 female connector.
The cable connection is “straight-through”.
Type
WI-CSER-905-9
26
Part No.
6720005105
WI-CSER-905-9
Serial to Serial Connectivity Cables
Accessories
COAXIAL CABLE KITS AND ACCESSORIES (continued)
Coaxial Surge Diverter WI-DIV-CCMA (-1 dB loss)
The WI-DIV-CCMA coaxial surge diverter is installed between the antenna and the
wireless unit to reduce lightning surges entering the module.
The WI-DIV-CCMA has an SMA connector and can be mounted directly to the module
- it is suitable for the 450 MHz, 968/900 MHz and 2.4 GHz products. It can be used
for 400MHz products with an SMA connector for added protection, however these
already have an internal surge diverter.
A surge diverter is normally not required where an antenna is surrounded by a lot of
steelwork, as in an industrial plant. The WI-DIV-CCMA is recommended where the
antenna installation is NOT surrounded by steelwork, or in areas of high electrical
storm activity where additional protection is desired.
The WI-DIV-CCMA requires additional weatherproofing if used externally.
If the module is mounted in a high vibration area or if large diameter coaxial cable
(low loss) is being used, then the WI-DIV-CCMA should not be mounted directly onto
the module. In these circumstances a short coaxial “tail” should be inserted between
the module and the WI-DIV-CCMA.
The WI-DIV-CCMA will only work effectively with a good ground connection. The
ground connection on the CSD, and the ground connection on the wireless module
must be connected together. The common ground should be connected to the same
ground point as the antenna mounting.
WI-DIV-CCMA
Coaxial Surge Diverter
Warning: Do not stay near operating equipment during an electrical storm.
The surge diverter will not provide protection to personnel.
Type
WI-DIV-CCMA
Part No.
6720005111
ANTENNA MOUNTING ACCESSORIES
Collinear Mounting Brackets WI-BR-CLR-KIT
The Collinear antenna requires two mounting brackets to hold the antenna in position.
The bracket assemblies consist of 1xU-Bolt 3xD-plates with nuts and washers in each
set. The brackets are zinc plated mild steel.
This simple method of mounting provides a solid support that will support the antenna
for many years.
This mounting provides an excellent earth to the main pole. This pole should preferably have a low resistance to ground.
Mounting brackets may be replaced if the antenna is dismantled for maintenance.
The brackets are suitable for pole sizes up to a maximum 2" (50mm) in diameter.
Type
WI-BR-CLR-KIT
WI-BR-CLR-KIT
Collinear Mounting Brackets
Part No.
6720005110
Yagi Mounting Bracket WI-BR-YAGI-KIT
The Yagi antenna requires a single mounting bracket. The bracket assembly consists
of 1xU-Bolt 1xD-plate with nuts and washers. The brackets are zinc plated mild steel.
This simple method of mounting provides a solid support that will permanently support
the antenna.
This mounting also provides an excellent earth to the main pole. This pole should
preferably have a low resistance to ground.
Mounting brackets may be replaced if the antenna is dismantled for maintenance.
WI-BR-YAGI-KIT
Yagi Mounting Bracket
The brackets are suitable for pole sizes up to a maximum 2" (50mm) in diameter.
Type
WI-BR-YAGI-KIT
Part No.
6720005109
WI-PS110/20
For wireless products that will accept 20 VDC. The plug pin arrangement is suitable
for 110V power sockets
Type
WI-PS110/20
Part No.
6720005104
WI-PS110/20
27
www.weidmuller.com
Argentina
Australia
Austria
Azerbaijan
Bahrain
Belarus
Belgium
BosniaHerzegovina
Brazil
Bulgaria
Canada
Chile
China
Colombia
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Estonia
Finland
France
Germany
Greece
Hong Kong
Hungary
Iceland
India
Indonesia
Iran
Ireland
Israel
Italy
Japan
Jordan
Kazakhstan
Kuwait
Latvia
Lebanon
Lithuania
Luxembourg
Macedonia
Malaysia
Malta
Mexico
Montenegro
Netherlands
New Zealand
Norway
Oman
Paraguay
Peru
Philippines
Poland
Portugal
Qatar
Romania
Russia
Saudi Arabia
Serbia
Weidmuller, Canada
10 Spy Court
Markham, Ontario L3R 5H6
Telephone: (800) 268-4080
Facsimile: (905) 475-2798
Email:
info1@weidmuller.ca
Website:
www.weidmuller.ca
12/07 • 7.5M • LIT0705
Singapore
Slovakia
Slovenia
South Africa
South Korea
Spain
Sweden
Switzerland
Syria
Taiwan
Thailand
Turkey
UAE
Ukraine
United Kingdom
Uruguay
USA
Venezuela
Vietnam
Yemen
Weidmuller is the leading manufacturer of components
for electrical connection technology to transmit energy,
signals and data. The Weidmuller product portfolio
ranges from terminal blocks, PCB connectors and
terminals, protected components, Industrial Ethernet
components, I/O components and relay sockets to
power supplies and overvoltage protection modules
suitable for all applications. Assemble Services, marking
solutions with a variety of tools and software systems,
round off the range. As an OEM supplier, the company
sets global standards in the field of electrical connection
technology.
Weidmuller, Mexico
Blvd. Hermanos Serdán 698,
Col. San Rafael Oriente
Puebla, Puebla, Mexico
C.P. 72029,
Telephone: 01 222 2686267
Facsimile: 01 222 2686219
Email:
clientes@weidmuller.com.mx
Website:
www.weidmuller.com.mx
Weidmuller, United States
821 Southlake Blvd.
Richmond, Virginia 23236
Telephone: (800) 849-9343
Facsimile: (804) 379-2593
Email:
info@weidmuller.com
Website:
www.weidmuller.com