Accessory Packages for the Allegiant

Video | Accessory Packages for the Allegiant
Accessory Packages for the Allegiant
www.boschsecurity.com
The Allegiant accessory products provide many
optional features to the base Allegiant Video Switcher/
Control System. Various accessory products are
available, including operator keyboards, code
distribution units, data converters, receiver/drivers,
and various port expanders. Where applicable, all
accessory products are designed to be compatible
throughout the Allegiant systems.
In addition to Allegiant accessories, this data sheet
also includes brief information on other products
typically used with the Allegiant Series of matrix
switchers.
In some cases, complete information for a product is
found in a separate datasheet.
Accessory Items
AutoDome Series
PTZ Cameras
LTC 8560 Series
Receiver/Drivers
LTC 8561 Series
Receiver/Drivers
LTC 8562 Series
Receiver/Drivers
LTC 8563 Series
Receiver/Drivers
LTC 8564 Series
Receiver/Drivers
LTC 8566 Series
Receiver/Drivers
LTC 8569 Series
Code Merger Units
LTC 8570 Series
Code Merger Units
LTC 8571 Series
Code Merger Units
LTC 8572 Series
Code Merger Units
Model No.
Description
LTC 8770 Series
Relay Units
IntuiKey Series
Keyboard
LTC 8712 Series
Console Port Expander Units
LTC 8555 Series
Keyboard
LTC 8713 Series
Alarm Port Expanders
LTC 8558/00
Keyboard Extension Cable
LTC 8714 Series
Keyboard Port Expanders
LTC 8557 Series
Keyboard Extension Kits
LTC 8715 Series
Keyboard Port Expanders
LTC 8568/00
Signal Distribution Unit
LTC 8780 Series
Data Converter Units
LTC 8768/00
Signal Distribution Unit
LTC 8782 Series
Code Translator Units
LTC 8540/00
Alarm Interface Unit
LTC 8785 Series
Code Converter Units
2 | Accessory Packages for the Allegiant
LTC 8786 Series
Code Converter Units
LTC 8016/90
Bilinx Data Interface Unit
LTC 8808/00
Video Interconnect Panel/Cables
LTC 8807/00
Video Interconnect Panel
LTC 8809 Series
Ribbon Cables
LTC 8506/00
Cable, PC-to-Console Port
LTC 8508/01
Ribbon to BNC Interface Cable
Certifications and approvals
Electromagnetic
Compatibility
(EMC)
Complies with FCC Part 15, ICES-003 and CE
regulations
Product Safety
Complies with CE regulations, UL, CSA, EN and
IEC Standards
Technical specifications
General Specifications
Environmental
Note: Specifications for electronic hardware products are noted below
unless otherwise specified in applicable accessory section.
Temperature
Operating
4°C to 50°C (40°F to 122°F)
Humidity
0% to 95% relative, non-condensing
Shock
50 g, 11 ms, ½ sine
Altitude
3000 m (10,000 ft)
and zoom lens controls for operating fixed or variable
speed pan/tilt/zoom equipped cameras. The
keyboards are available in the following configurations:
Model Number
Top Bezel Graphics
Communication Protocol
LTC 8555/00
English
RS-485
LTC 8555/01
Icons
RS-485
LTC 8555/02
English
RS-232
LTC 8555/03
Icons
RS-232
Electrical
Operating Voltage
12 VAC (supplied by main Allegiant CPU bay
or optional Keyboard Extension Kit)
Signal
2 wire RS-485, 9600 baud (LTC 8555/00
and LTC 8555/01 models) 3 wire RS-232,
9600 baud (LTC 8555/02 and
LTC 8555/03 models)
Connectors
One (1), 6-contact connector for data/power
Mechanical
Construction/
Finish
High impact plastic case with charcoal color
Dimensions
(W x D x H)
220 x 51 x 155 mm (8.67 x 2.00 x 6.11 in.)
Weight
0.55 kg (1.22 lb)
LTC 8558/00 Keyboard Extension Cable
Six-conductor extension cable carries data/power for
remote IntuiKey Series or LTC 8555 Series keyboards
up to 30 m (100 ft) away from main Allegiant CPU bay.
IntuiKey Keyboard
The IntuiKey KBD-Universal is a full function keyboard
used for control and programming of the Allegiant
Series matrix switchers. Backlit LCD screens provide
multi-language display of softkey menus and status
information. Integral variable speed joystick and zoom
lens controls are standard for operating fixed or
variable speed pan/tilt/zoom equipped cameras. In
addition to the Allegiant Series, the KBD- Universal
model IntuiKey can be used to simultaneously control
Divar Series DVRs, and System4 Series multiplexers.
The optional PC-based IntuiKey Script Application
software package can be used to define softkeys that
are used to activate Allegiant system Command
Scripts.
The optional KBD-RACK rack-mounting kit is designed
to provide vertical, horizontal, or 45 degree inclined
mounting into standard EIA 48 cm (19 in.) rack.
Refer to the IntuiKey Series data sheet for complete
specifications.
LTC 8557 Series Keyboard Extension Kits
Interface kit used to remote IntuiKey Series or
LTC 8555 Series keyboards up to 1.5 km (5000 ft)
away from main CPU bay. Customer supplied 0.5 mm2
(24 AWG) shielded-twisted pair (Belden 9841 or
equivalent) required between main CPU bay site and
keyboard site. Kit provides two junction boxes,
interface cable, and appropriate keyboard power
supply.
Indicators
Junction box mounted power LED
LTC 8555 Series Keyboards
The LTC 8555 Series are compact, full function
keyboards for use with Allegiant Series matrix
switchers. LED readouts display real time system
status information. Includes variable speed joystick
Connectors
One (1), 4-position screw terminal block. One (1),
6-contact keyboard cable connector.
Electrical
Model No.
Rated Voltage1
Voltage Range
Power
LTC 8557/60
120 VAC,
50/60 Hz
108 to 132
10 W
LTC 8557/50
230 VAC,
50/60 Hz
198 to 264
15 W
1. Input voltage of included power supply.
3 | Accessory Packages for the Allegiant
Mechanical
Construction/
Finish
Surface mountable, flat black painted metal
enclosure
Dimensions
(W x D x H)
121 x 70 x 35 mm (4.75 x 2.75 x 1.375 in.)
Weight
170 g (6 oz.)
LTC 8568/00 Signal Distribution Unit
Main site Bi-Phase control code distribution and line
driver unit for communicating to AutoDome Series
cameras, receiver/drivers, switcher/ followers, and
Allegiant satellite systems. The unit provides 32
separate outputs for driving up to 256 remote devices.
Either “star” or “daisy chain” wiring configurations
may be used. Two meter (6 ft) interface cable for
data/power between unit and main Allegiant CPU bay
supplied. Not applicable to the LTC 8100, LTC 8200,
and the LTC 8300 Series systems.
Electrical
inputs may be configured in groups of 32 to accept
either normally open or normally closed contacts. Unit
also contains eight relay outputs that activate
automatically upon alarm conditions. A two meter
(6 ft) interface cable for data/power between unit and
main CPU bay is supplied. Not applicable to the
LTC 8100, LTC 8200, and the LTC 8300 Series
systems.
Electrical
Operating Voltage
12 VAC or 12 VDC
(12 VAC is supplied by main CPU bay)
Power
8W
Indicators
Power
LED
Alarm
LED; audible tone
Connectors
Alarm Inputs
Sixty-four (64); twenty 6-contact removable
screw terminal blocks
3W
Alarm Outputs
Eight (8) relay outputs (100 VDC, 0.5 A, 10 W);
four (4), 6-contact removable screw terminal
block.
• Power
LED
Data/Power
One 9-pin Sub D connector
• Code
LED
Mechanical
One (1), 9-pin Sub D connector for data/power
Construction/
Finish
Charcoal colored metal enclosure
Input
Outputs
Sixteen, 6-contact removable screw terminal
blocks for code output. Maximum transmission
distance is 1.5 km (5000 ft) using 1 mm2
(18 AWG) shielded-twisted pair (Belden 8760 or
equivalent).
Dimensions
(W x D x H)
445 x 318 x 89 mm (17.5 x 12.5 x 3.5 in.)
Integral mounting flanges for EIA 48 cm (19 in.)
rack
Weight
1.8 kg (4 lb)
Operating Voltage
12 VAC (supplied by main CPU bay)
Power
Indicators
Connectors
Mechanical
Construction/
Finish
Charcoal colored metal enclosure
Dimensions
(W x D x H)
445 x 318 x 89 mm (17.5 x 12.5 x 3.5 in.)
Integral mounting flanges for EIA 48 cm (19 in.)
rack
Weight
1.8 kg (4 lb)
LTC 8768/00 Signal Distribution Unit
Same features and specifications as the LTC 8568/00
except that it contains twice the number of output
connectors which provide 64 separate outputs for
driving up to 512 remote devices. Not applicable to
the LTC 8100, LTC 8200, and the LTC 8300 Series
systems.
LTC 8540/00 Alarm Interface Unit
Unit accepts up to 64 contact closures or logic level
inputs from remote sensing devices such as door
contacts, PIRs, etc. and then reports the “alarm”
information to the main Allegiant CPU bay. Alarm
AutoDome and AutoDome Easy IISeries
The AutoDome® and the AutoDome Easy II Series of
cameras integrates high-speed panning and tilting,
360-degree continuous rotation, pre-positions, etc. in
a small, easy-to-install lightweight package. These PTZ
models are available with various mounting and
configuration options for use in both internal and
external environments.
Refer to the AutoDome and the AutoDome Easy II
Series datasheets for complete specifications.
LTC 8560, LTC 8561, LTC 8562, LTC 8563, LTC 8564,
and LTC 8566 Series Receiver/Drivers
These series of on-site receiver/drivers are designed to
receive Bi-Phase control code and convert this data
into signals for controlling conventional pan/tilt, zoom
lenses, and auxiliary functions. Supplied in an
environmentally rated enclosure, these series of
receiver/drivers are available in both basic and fullfeatured models. Refer to the chart below for specific
model selection based on desired operating voltages
and features:
4 | Accessory Packages for the Allegiant
Model
Features
Input Voltage
P/T Output Voltage
LTC 8569/5
0,
LTC 8570/5
0,
LTC 8571/5
0,
LTC 8572/5
0
230 VAC,
50/60 Hz
198 to 264
12 W
LTC 8560/6
0
Basic
120 VAC
120 VAC
LTC 8560/5
0
Basic
230 VAC
230 VAC
LTC 8561/6
0
Full
120 VAC
120 VAC
LTC 8561/5
0
Full
230 VAC
230 VAC
LTC 8562/6
0
Basic
120 VAC
24 VAC
LTC 8562/5
0
Basic
230 VAC
24 VAC
Inputs
Two (2), 9-pin Sub D connectors (four (4) with
LTC 8570 Series and LTC 8572 Series)
LTC 8563/2
0
Basic
24 VAC
24 VAC
Outputs
LTC 8564/2
0
Full
24 VAC
24 VAC
Sixteen (32 on LTC 8571 and LTC 8572 Series) 6contact removable screw terminal blocks for code
output. Maximum transmission distance is 1.5 km
(5000 ft.) using 1 mm2 (18 AWG) shielded-twisted
pair (Belden 8760 or equivalent).
LTC 8566/6
0
Full
120 VAC
24 VAC
AC Input
3-wire power cord with grounded plug; 1.8 m (6 ft)
long
LTC
8566/50
Full
230 VAC
24 VAC
Indicators
Power
LED
Code
LED
Connectors
Mechanical
Refer to the LTC 8560 Series and/or LTC 8561 Series datasheets for
complete specifications.
Construction/
Finish
Charcoal colored metal enclosure
LTC 8569, LTC 8570, LTC 8571, LTC 8572 Series
Code Merger Units
Control code merger and line driver units used to
combine Allegiant Bi-Phase control code from two (up
to four with LTC 8570 and LTC 8572 versions) systems
for communicating to AutoDome Series cameras,
receiver/drivers, switcher/followers, and Allegiant
Satellite systems. The LTC 8569, LTC 8570 Series
provides 32 separate outputs capable of driving up to
256 remote devices. The LTC 8571, LTC 8572 Series
provides 64 separate outputs capable of driving up to
512 remote devices. Either “star” or “daisy chain”
wiring configurations may be used. Two data cables
for interface to Allegiant main CPU bays are supplied
(four with LTC 8570 and LTC 8572).
Unit will accept signal input either from Allegiant main
CPU bay, LTC 8568/00 output, LTC 8780 Bi-Phase
output, or an output from another LTC 8569, LTC 8570
Series or LTC 8571, LTC 8572 Series unit. Multiple
units may be cascaded to obtain additional outputs.
Dimensions
(W x D x H)
445 x 318 x 89 mm (17.5 x 12.5 x 3.5 in.)
Integral mounting flanges for EIA 48 cm (19 in.)
rack
Weight
5.3 kg (11.7 lb)
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8569/6
0,
LTC 8570/6
0,
LTC 8571/6
0,
LTC 8572/6
0
120 VAC,
50/60 Hz
108 to 132
12 W
LTC 8770 Series Relay Units
The LTC 8770 Series are relay units that are designed
to operate with devices that generate Allegiant BiPhase control code. These devices include the
Allegiant series of video matrix switcher/controllers,
System4 series of multiplexers, LTC 5136 controller
series, etc. The LTC 8770 receives Bi-Phase control
signals and opens or closes relays, depending upon
the desired operating mode. Each LTC 8770 unit
provides 24 individually isolated relays for connecting
to external devices. In addition, six functional
operating modes are available, including one user
activated test mode.
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8770/5
0
230 VAC,
50/60 Hz
198 to 264
8W
LTC 8770/6
0
230 VAC,
50/60 Hz
105 to 132
8W
Indicators
Power and data transmission activity displayed using
LEDs. Device number or logical relay number
indicated by a 4-position thumbwheel switch located
on the rear panel.
5 | Accessory Packages for the Allegiant
Mechanical
Connectors
Inputs
One (1), 3-pin removable screw terminal connector,
located on the rear panel; communication port where
Bi-Phase commands are received
Outputs
Four (4), 12-pin removable screw terminal connectors
located on the rear panel; relay contact (0.5 A at
20 VAC/DC and a maximum resistive load of 10 VA)
36 peak volts from either pin of the relay to ground
AC Input
3-wire power cord with grounded plug; 1.8 m (6 ft)
long
Mechanical
Construction/
Finish
Steel chassis with sheet metal cover and
plastic bezel. Charcoal colored case.
Dimensions
(W x D x H)
223 x 280 x 40 mm
(8.77 x 11 x 1.59 in.)
Weight
1.9 kg (4.3 lb)
Optional Rack Mount Kit
LTC 9101/00 (Holds 1 or 2 units)
LTC 8712 Series CONSOLE Port Expanders
The LTC 8712 Series “expands” an Allegiant system's
CONSOLE port to permit up to 4 external computing
devices to communicate with the system via RS-232
protocol. Any computing device that can normally
communicate directly with an Allegiant via its RS-232
CONSOLE port can be used with these port
expanders. The external devices can consist of PCs
running the Allegiant system's Master Control
Software package, the Allegiant Graphical User
Interface (GUI), access control systems, Allegiant
series RS-232 keyboards, or other devices utilizing the
Allegiant system's Command Console Language (CCL).
The LTC 8712 Series can be used with the LTC 8100,
LTC 8200, LTC 8300, LTC 8500, LTC 8600, LTC 8800,
or LTC 8900 Series systems containing CPU software
version 6.5 or higher.
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8712/60
120 VAC, 50/60 Hz
108 to 132
10 W
LTC 8712/50
230 VAC, 50/60 Hz
198 to 264
10 W
Indicators
Power and data transmission activity displayed using
LEDs
Connectors
Inputs
One (1), 9-pin Sub D connector; provides RS-232
interface to Allegiant bay. Two-meter (6-ft)
interconnect cable to main bay supplied
Outputs
Four (4), 9-pin Sub D connectors for RS-232
interface to up to four external devices
AC Input
3-wire power cord with grounded plug; 1.8 m (6 ft)
long
Construction/
Finish
Steel chassis with sheet metal cover and
plastic bezel. Charcoal colored case.
Dimensions
(W x D x H)
223 x 280 x 40 mm
(8.77 x 11 x 1.59 in.)
Weight
1.9 kg (4.3 lb)
Optional Rack Mount Kit
LTC 9101/00 (Holds 1 or 2 units)
LTC 8713 Series Alarm Port Expander
The LTC 8713 Series interfaces to a LTC 8500,
LTC 8600, LTC 8800, or LTC 8900 Series alarm port to
permit additional LTC 8540/00 Alarm Interface units to
be connected to the system. A single LTC 8713 series
alarm port expander supports up to four LTC 8540/00
alarm interface units. This provides the capability for
up to 256 alarm input points. Multiple LTC 8713 units
may be combined to provide up to 1024 alarm input
points using up to sixteen LTC 8540/00 units. The
actual number of units that can be used in a system
depends upon the model of the Allegiant system being
used. System interconnect cable is included. A
separate 12 VAC or DC, 8 W power supply is required
for each LTC 8540/00.
Alarm Capacities
Allegiant Model
No.
Maximum No.
of Alarms
Maximum No.
of LTC 8713
Maximum No.
of
LTC 8540/00
LTC 8500
128
1
2
LTC 8600
512
3
8
LTC 8800
1024
5
16
LTC 8900
1024
5
16
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8713/60
120 VAC,
50/60 Hz
108 to 132
10 W
LTC 8713/50
230 VAC,
50/60 Hz
198 to 264
10 W
Indicators
Power and data transmission activity displayed using
LEDs.
Connectors
Inputs
One (1), 9-pin Sub D connector; provides RS-232
interface to main Allegiant bay. Two-meter (6-ft)
interconnect cable to main bay supplied.
6 | Accessory Packages for the Allegiant
Outputs
AC Input
Four (4), non-powered, 9-pin Sub D connectors for
RS‑232 interface to up to four expanded
LTC 8540/00 units. Data cables supplied with
LTC 8540/00 are used to connect alarm interfaces to
port expander. A separate 12 VAC or DC, 8 W power
supply is required for each LTC 8540/00.
3-wire power cord with grounded plug; 1.8 m (6 ft)
long
Mechanical
Construction/
Finish
Steel chassis with sheet metal cover and
plastic bezel. Charcoal colored case.
Dimensions
(W x D x H)
223 x 280 x 40 mm
(8.77 x 11 x 1.59 in.)
Weight
1.9 kg (4.3 lb)
Optional Rack Mount Kit
LTC 9101/00 (Holds 1 or 2 units)
LTC 8714 Series and LTC 8715 Series Keyboard Port
Expanders
The LTC 8714 Series and the LTC 8715 Series are port
expander accessory units used to provide additional
keyboard capacity for LTC 8600, LTC 8800, or
LTC 8900 Series Allegiant systems. A single LTC 8714
Series unit can be used to interface up to eight
keyboards with an allegiant system. A single LTC 8715
Series is used to interface up to four LTC 8714 Series
expanders in a system. Multiple LTC 8715 Series
expanders can be used along with multiple LTC 8714
Series expanders to provide up to 64 keyboards in a
system. The actual number of units that can be used in
a system depends upon the model of the Allegiant
system.
Allegiant System Capacities
Allegiant
Model No.
Maximum No.
of Keyboards
Maximum No.
of LTC 8714
Maximum No.
of LTC 8715
LTC 8600
16
1
0
LTC 8800
32
3
1
LTC 8900
64
7
3
The above table assumes eight system keyboards are
connected directly into the Allegiant CPU bay
keyboard ports. An LTC 8557 Series keyboard hookup
kit is required for each expanded keyboard. LTC 8714
and LTC 8715 port expanders can only be used on
LTC 8600, LTC 8800, and LTC 8900 systems
containing CPU software version 6.2 or later.
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8714/60
120 VAC, 50/60 Hz
108 to 132
10 W
LTC 8715/60
120 VAC, 50/60 Hz
108 to 132
10 W
LTC 8714/50
230 VAC, 50/60 Hz
198 to 264
10 W
LTC 8715/50
230 VAC, 50/60 Hz
198 to 264
10 W
Indicators
Power and data transmission activity displayed using
LEDs
LTC 8714 Series Connectors
Interface Data Port: One (1), 9-pin Sub D connector
provides data interface to COM 2 port of main
Allegiant CPU bay or to expansion port of LTC 8715
Series. Two-meter (6-ft) interconnect cable supplied.
Keyboard Data Ports: Eight (8), 6-contact nonpowered Allegiant series keyboard cable connectors.
An LTC 8557 Series keyboard hookup kits are required
for each Allegiant LTC 8555 series keyboard to be
interfaced to LTC 8714 Series. For the IntuiKey Series
keyboards, a separate power pack can be used.
LTC 8715 Series Connectors
Interface Data Ports: Five (5), 9-pin, Sub D connectors
provide data interface to COM 2 port of main Allegiant
CPU bay and data interface for up to four LTC 8714
Series units. Two-meter (6-ft) interconnect cable for
main bay interface supplied.
AC Input: 3-wire power cord with grounded plug;
1.8 m (6 ft) long.
Mechanical
Construction/
Finish
Steel chassis with sheet metal cover and
plastic bezel. Charcoal colored case.
Dimensions
(W x D x H)
223 x 280 x 40 mm
(8.77 x 11 x 1.59 in.)
Weight
1.9 kg (4.3 lb)
Optional Rack Mount Kit
LTC 9101/00 (Holds 1 or 2 units)
LTC 8780 Series Data Converter Units
The LTC 8780 Series are accessory units that convert
the Allegiant system's Bi-Phase control code into
RS-232, or converts RS-232 back to Bi-Phase code.
This provides the capability of transmitting the control
code over conventional RS-232 transmission mediums
such as phone modems, fiber optics, microwaves, etc.
The unit will accept the Bi-Phase control code
generated by an Allegiant main CPU bay, a
LTC 8568/00 Signal Distribution unit, or an output
from a LTC 8569, LTC 8570 Series or LTC 8571,
LTC 8572 Series Code Merger unit.
The LTC 8780 Series are also designed to perform the
Satellite selector functions in an Allegiant Satellite
system configuration. In addition, using its integral
signal distribution capability, the LTC 8780 Series can
function as a remote distribution unit providing 15
separate outputs. As a distribution unit, wiring can be
in either a “star” or “daisy chain” configuration and
each output is capable of driving 8 receiver/driver
loads at up to 1.5 km (5000 ft) away using 1 mm2
(18 AWG) shielded-twisted pair (Belden 8760 or
equivalent).
Refer to separate datasheet for complete
specifications.
7 | Accessory Packages for the Allegiant
LTC 8782 Series Code Translator Units
The LTC 8782 Series Code Translators are accessory
units that convert Bi-Phase code to other
manufactures’ control codes, or convert other
manufactures’ codes to Bi-Phase. Many of the most
popular protocol codes are supported, including
Pelco, Vicon, American Dynamics, Sensormatic,
Kalatel, Diamond Electronics, and Javelin. Fixed and
variable speed codes are supported where applicable.
The LTC 8782 Series Code Translators have four
independent outputs. Removable screw terminal
blocks are used for input and output connections. The
Front panel LEDs indicate the status of power, data
receive, and data transmit. The translator comes
supplied in an EIA 48 cm (19 in.) rack-mount adapter
that can hold up to three units.
Refer to the LTC 8782 series data sheet for complete
specifications.
LTC 8785 Series Code Converters
LTC 8785 Series units are designed for use in very old
Allegiant systems that have been upgraded to support
‘variable speed’ control code protocol. The LTC 8785
units are used to provide a source of 'fixed speed'
control code when the system is generating the new
‘variable speed’ control code preferred by the
AutoDome series of PTZ cameras. The LTC 8785
receives variable speed control code from the Allegiant
via its LTC 8568/00 Signal Distribution unit and
converts it into appropriate fixed speed control code.
The ‘fixed speed’ control code outputs from the
LTC 8785 Series connect to the older TC8561 Series
receiver/drivers using the existing field cabling.
Electrical
Model No.
Rated Voltage
Voltage Range
Power
LTC 8785/6
0
120 VAC, 50/60 Hz
108 to 132
12 W
LTC 8785/5
0
230 VAC, 50/60 Hz
198 to 265
12 W
Indicators
• Power
LED
• Code
LED
Connectors
Inputs
One (1), 9-pin Sub D connector
Outputs
Sixteen (16), 6-contact removable screw terminal
blocks for code output. Maximum transmission
distance is 1.5 km (5000 ft) using 1 mm2 (18 AWG)
shielded twisted pair (Belden 8760 or equivalent).
AC Input
3-wire power cord with grounded plug; 1.8 m (6 ft)
long
Mechanical
Construction/
Finish
Charcoal colored metal enclosure
Dimensions
(W x D x H)
445 x 318 x 89 mm (17.5 x 12.5 x 3.5 in.)
Integral mounting flanges for EIA 22.86 cm
(9 in.) rack
Weight
5.3 kg (11.7 lb)
LTC 8786 Data Converter Series
The LTC 8786 Series of data converters are designed
to convert Bosch “Receiver/Driver and AutoDome
RS-232 Control Code Protocol” into Allegiant Bi-Phase
control code. These units are the preferred method for
transforming a single RS-232 data output from a DVR
(or a similar device) into multiple control code outputs
for operating AutoDome cameras. Either “star” or
“daisy chain” wiring configurations can be used from
each of its 16 outputs. Using daisy chain, each output
is capable of driving 8 receiver/driver loads at up to
1.5 km (5000 ft.) away using 1 mm2 (18 AWG)
shielded-twisted pair (Belden 8760 or equivalent).
Refer to the LTC 8786 series datasheet for complete
specifications.
LTC 8016/90 Bilinx™ Data Interface Unit
The LTC 8016/90 Allegiant Bilinx Data Interface unit is
an accessory used for communicating over-the-coax,
with up to 16 Bilinx-capable AutoDome® and/or
Dinion™ Series cameras. Compatible with all seven
Allegiant Series matrix switcher/controllers, the
LTC 8016 provides complete control of pan/tilt/zoom,
auxiliaries, and pre-position functions of Bilinx enabled
AutoDome Series cameras. In addition, complete
programming of Dinion Series cameras and
AutoDomes via their on-screen menus is supported.
Bilinx technology also supports camera-generated
event reporting to the Allegiant. This allows remote
alarm inputs and motion event data to be sent by the
camera to the Allegiant without the need for additional
wiring between the camera site and the main control
location.
In addition, the LTC 8016 is designed so that other BiPhase code generating products, like Bosch Digital
Videos Recorders, can be used with the unit for
control of PTZ functions and camera menu access over
the video cable.
The LTC 8016 is supplied in an enclosure compatible
with mounting in an EIA 48 cm (19 in.) rack, requiring
only a 1-U rack height. To support large systems, up to
31 units can be cascaded, comprising up to 496 Bilinxcompatible cameras.
The LTC 8016 can also be used to transmit Bilinx
communications over a number of video transmission
systems. Example devices include fiber optic links and
external balun devices that use CAT5 twisted pair
cables for video communication.
Refer to the LTC 8016/90 datasheet for complete
specifications.
8 | Accessory Packages for the Allegiant
LTC 8808/00 Video Interconnect Panel
The LTC 8808/00 Video Interconnect panel provides
the LTC 8200, LTC 8300 Series, LTC 8600 Series, and
LTC 8800 Series systems the ability of looping up to
32 video inputs per panel. This 'patch' panel contains
32 BNC connectors on its front panel for external
video connections and two 16-contact ribbon
connectors on its rear panel. Two, 2-meter (6-ft)
16‑conductor video grade ribbon cables are included
for interfacing the patch panel to the video looping
connectors on the rear panel of the LTC 8200,
LTC 8300 Series, LTC 8600 Series, and LTC 8800
Series equipment bays.
LTC 8506/00 Allegiant Console Cable
The LTC 8506/00 is an RS-232 grade cable with 9-pin,
Sub D-connectors on each end that is used to connect
an Allegiant’s system’s Console port to a standard PC
Com port. This cable is included in the Allegiant
LTC 8059 Master Control Software and the LTC 8850
Allegiant GUI packages.
Length: 3 m (10 ft), approximately.
Construction/
Finish
Charcoal painted metal
Size
One standard EIA 48 cm (19 in.) rack unit high
and one unit wide. Integral mounting flange
design.
LTC 8508/01 Ribbon-to-BNC Interface Cable
The LTC 8508/01 is a video interface cable with a 34pin ribbon cable on one end and 16 male BNC
connectors on the other end. This cable can be used
to loop up to 16-channels of video signals from
products having the ribbon cable connector interface
to other devices that utilize BNC connectors. Typical
products with 34-pin ribbon cable connector
interfaces include the LTC 8016/90 Bilinx Data
Interface unit and the DESAXL series digital video
recorder.
Length: 1 m (3 ft), approximately
Weight
0.8 kg (1.8 lb)
Ordering information
Mechanical
LTC 8807/00 Video Interconnect Panel
The LTC 8807/00 Video Interconnect Panel is identical
to the LTC 8808/00 described above, except that it
does not include the two video ribbon cables. This
video interconnect panel is intended for use with
products that are supplied with video ribbon cables,
such as the LTC 8016/90 Bilinx Data Interface unit.
For example, the ribbon cables from up to two
LTC 8016 units can be converted into 32 standard
female BNC connectors using this interface panel. This
configuration is necessary when the LTC 8016 unit will
be separated from the control unit beyond a 2 m (6 ft)
distance.
LTC 8553/00 Keyboard
LTC 8809 Series Video Ribbon Cables
The LTC 8809 series are 16-channel video ribbon
cables that are used to provide connections between
certain devices. Specifically designed for the transport
of 75 Ohm video signals, these cables are available in
three different lengths:
LTC 8555/00 Compact Full-function Keyboard
Similar to the LTC 8550/00 keyboard except contains
variable speed joystick for use in Allegiant systems
where variable speed pan/tilt control is desired using
AutoDome pan/tilt/zoom/cameras.
Order number LTC 8553/00
LTC 8553/01 Keyboard
Similar to LTC 8550/01 keyboard except contains
variable speed joystick for use in Allegiant systems
where variable speed pan/tilt control is desired using
AutoDome® pan/tilt/zoom/cameras.
Order number LTC8553/01
variable speed joystick
Order number LTC 8555/00
LTC 8555/01 Compact Full-function Keyboard
variable speed joystick, icon graphics
Order number LTC 8555/01
Model Number
Length
LTC 8809/00
2 m (6 ft)
LTC 8809/01
1 m (3 ft)
Order number LTC 8555/02
LTC 8809/02
3.2 m (10.5 ft)
LTC 8555/03 Compact Full-function Keyboard
Each cable contains a 34-pin connector at each end
that is designed to ‘lock’ into the corresponding
connector found on the rear panels of the Allegiant
LTC 8800 and LTC 8900 series matrix switchers. In
addition, these cables are supplied with certain other
products, including the LTC 8808/00 Video
Interconnect Panel and the LTC 8016/90 Bilinx Data
Interface unit.
LTC 8555/02 Compact Full-function Keyboard
variable speed joystick, RS-232 protocol
variable speed joystick, RS-232 protocol, icon graphics
Order number LTC 8555/03
LTC 8540/00 Alarm Interface Unit
Alarm interface, 64 alarm inputs, 8 relay closures
Order number LTC 8540/00
LTC 8558/00 Keyboard Cable
optional, 30.5 m (100 ft)
Order number LTC 8558/00
9 | Accessory Packages for the Allegiant
LTC 8568/00 Signal Distribution Unit
LTC 8714/50 Keyboard Port Expander
32 separate biphase outputs
for up to 8 Allegiant keyboards, half rack 230 VAC,
50 Hz
Order number LTC 8568/00
LTC 8768/00 Signal Distribution Unit
64 separate biphase outputs
Order number LTC 8768/00
LTC 8569/50 Code Merger Unit
allows 2 Biphase devices to control 32 outputs,
230 VAC, 50 Hz
Order number LTC 8569/50
LTC 8569/60 Code Merger Unit
allows 2 Biphase devices to control 32 outputs,
120 VAC, 50/60 Hz
Order number LTC 8569/60
LTC 8570/50 Code Merger Unit
allows 4 Biphase devices to control 32 outputs,
230 VAC, 50 Hz
Order number LTC 8570/50
LTC 8570/60 Code Merger Unit
allows 4 Biphase devices to control 32 outputs,
120 VAC, 50/60 Hz
Order number LTC 8570/60
LTC 8571/50 Code Merger Unit
allows 2 Biphase devices to control 64 outputs,
230 VAC, 50 Hz
Order number LTC 8714/50
LTC 8714/60 Keyboard Port Expander
for up to 8 Allegiant keyboards, half rack, 115 VAC,
60 Hz
Order number LTC 8714/60
LTC 8715/50 Port Expander
for multiple LTC 8714/50 units, 230 VAC, 50 Hz
Order number LTC 8715/50
LTC 8715/60 Port Expander
for multiple LTC 8714/60 units, half rack, 115 VAC,
60 Hz
Order number LTC 8715/60
LTC 8785/50 Data Converter Unit
converts var. speed to fixed speed code, 230 VAC,
50 Hz
Order number LTC 8785/50
LTC 8785/60 Data Converter Unit
converts var. speed code to fixed speed code,
120 VAC, 60 Hz
Order number LTC 8785/60
LTC 8808/00 Video Interconnect Panel
Video connect panel
Order number LTC 8571/50
Order number LTC 8808/00
LTC 8572/50 Code Merger Unit
LTC 8770/50 Switcher/Follower Unit
allows 4 Biphase devices to control 64 outputs,
230 VAC, 50 Hz
for Allegiant system, 24 relay contacts, half rack,
230 VAC, 50 Hz
Order number LTC 8572/50
Order number LTC 8770/50
LTC 8572/60 Code Merger Unit
LTC 8770/60 Switcher/Follower Unit
allows 4 Biphase devices to control 64 outputs,
120 VAC, 60 Hz
for Allegiant system, 24 relay contact, half rack,
120 VAC, 60 Hz
Order number LTC 8572/60
Order number LTC 8770/60
LTC 8712/50 Allegiant Console Port Expander
LTC 8506/00 Cable
for LTC 8600/LTC 8800 console port expander,
RS-232, 230 VAC, 50 Hz
Order number LTC 8712/50
LTC 8712/60 Allegiant Console Port Expander
for LTC 8600/LTC 8800 console port expander,
RS-232, 115 VAC, 60 Hz
Order number LTC 8712/60
LTC 8713/50 Alarm Port Expander
for up to 4 LTC 8540/00 units, half rack, 230 VAC,
50 Hz
Order number LTC 8713/50
LTC 8713/60 Alarm Port Expander
for up to 4 LTC 8540/00 units, half rack, 115 VAC,
60 Hz
Order number LTC 8713/60
PC-to-console port, for Allegiant Systems
Order number LTC 8506/00
LTC 8809/00 Ribbon Cable
16 conductor for LTC 8200, 8300, 8600, 8800 and
8900 Systems, 1.8 m (6 ft)
Order number LTC 8809/00
LTC 8809/01 Ribbon Cable
16 conductors, for LTC 8200, 8300, 8600, 8800, and
8900 Systems, 0.9 m (3 ft)
Order number LTC 8809/01
LTC 8809/02 Ribbon Cable
16 conductors, for LTC 8200, 8300, 8600, 8800, and
8900 Systems, 3 m (9.9 ft)
Order number LTC 8809/02
10 | Accessory Packages for the Allegiant
LTC 8781/50 Time/Date Converter Unit
provides output in GPS format, half rack, 230 VAC,
50 Hz
Order number LTC 8781/50
LTC 8781/60 Time/Date Converter Unit
provides output in GPS format
Order number LTC 8781/60
LTC 8560/50 Single-channel On-site Receiver/Driver
230 VAC pan/tilt voltage, 230 VAC power supply, no
auxiliary, 50°Hz
Order number LTC 8560/50
LTC 8560/60 Single-channel On-site Receiver/Driver
120 VAC pan/tilt voltage, 120°VAC power supply, no
auxiliary, 50/60 Hz
Order number LTC 8560/60
LTC 8780/50 Data Converter Unit
Allegiant biphase control code to RS-232, 230 VAC,
50 Hz
Order number LTC 8780/50
LTC 8780/60 Data Converter Unit
Allegiant Biphase control code to RS-232, 115 VAC,
60 Hz
Order number LTC 8780/60
LTC 8850/00 GUI Allegiant Single User Software Package
Complete with Allegiant and VCR server.
Order number LTC 8850/00
Represented by:
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems 2013 | Data subject to change without notice
2370757131 | en, V1, 04. Oct 2013
Asia-Pacific:
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
apr.securitysystems@bosch.com
www.boschsecurity.asia
China:
America Latina:
Bosch (Shanghai) Security Systems Ltd. Robert Bosch Ltda Security Systems Division
201 Building, No. 333 Fuquan Road
Via Anhanguera, Km 98
North IBP
CEP 13065-900
Changning District, Shanghai
Campinas, Sao Paulo, Brazil
200335 China
Phone: +55 19 2103 2860
Phone +86 21 22181111
Fax: +55 19 2103 2862
Fax: +86 21 22182398
latam.boschsecurity@bosch.com
www.boschsecurity.com.cn
www.boschsecurity.com