Zanussi ZCM 631 Technical data

MIXED
FUEL COOKER
ZCM 631
INSTRUCTION BOOKLET
GB
Please read this instruction booklet before using the appliance
Important Safety Information
You MUST read these warnings carefully before installing or using the appliance. If you need assistance,
contact our Customer Care Department on 08705 727727
Installation
l
l
l
l
l
l
This cooker must be installed by qualified personnel,
according to the manufacturer’s instructions and to
the relevant British Standards.
This cooker is heavy. Take care when moving it.
Any gas installation must be carried out by a
registered CORGI installer.
Remove all packaging before using the cooker.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Do not attempt to modify the cooker in any way.
l
l
Service
l
Child Safety
l
l
l
This cooker is designed to be operated by adults. Do
not allow children to play near or with the cooker.
The cooker gets hot when it is in use. Children should
be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the cooker.
Always ensure that the oven vent which is located at
the centre back of the hob is left unobstructed to
ensure ventilation of the oven cavity.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above the
cooker.
This cooker should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
l
l
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
During Use
l
l
l
l
l
l
l
l
l
l
l
2
This cooker is intended for domestic cooking only. It
is not designed for commercial or industrial purposes.
When in use a gas cooker will produce heat and
moisture in the room in which it has been installed.
Ensure there is a continuous air supply, keeping air
vents in good condition or installing a cooker hood
with a venting hose.
When using the cooker for a long period time, the
ventilation should be improved, by opening a window
or increasing the extractor speed.
Do not use this cooker if it is in contact with water.
Do not operate the cooker with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
Do not store flammable materials such as oven gloves,
tea towels etc. in the drawer.
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces
of the cooker.
Unstable or misshapen pans should not be used on
the hob burners as unstable pans can cause an
accident by tipping or spillage.
Never leave the cooker unattended when cooking with
oil and fats.
This cooker should be kept clean at all times. A
build-up of fats or foodstuffs could result in a fire.
Never use plastic dishes in the oven or on the hob
burners. Never line any part of the oven with aluminium
foil.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
These instructions are valid for UK only.
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
F
Step by step instructions for an operation
Hints and Tips
Environmental information
This appliance is manufactured according to the
following EEC directives:
73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC,
current edition.
Contents
For the User
For the Installer
Important Safety Information
2
Important Safety Requirements
19
Description of the Cooker
3
Instructions for the Installer
19
Using the Hob
5
Installation
20
Before the First Use of the Oven
6
Electrical connections
22
Using the Oven
6
Commissioning
23
24 hour Clock and Timer
7
Conversion from Natural to LPG Gas
23
Using the Conventional Oven
10
The Fan Oven
12
Defrosting
13
Grilling
14
Maintenance and Cleaning
15
Cleaning the Oven
16
Service and Spare Parts
17
Something Not Working
17
Customer Care Department
18
Guarantee Conditions
18
Oven Door Protection Device
All our appliances comply with the European safety
standards. Nevertheless, in order to ensure the
highest safety level, and avoid small children to be
exposed to the heat when the appliance is operated,
it is possible to fit a special ptotection device to the
oven door. This device can be purchased in our
Service Force Centres, specifying the relevant code
(35791) and the Product No. shown on the rating
plate.
Description of the Cooker
Splash back
Semi-rapid burner
Semi-rapid burner
Auxiliary burner
Triple-crown (ultra-rapid)
burner
Control panel
A
U
T
O
TIMER
ZCG 6000
Shelf
Oven door
Storage drawer
3
Control Panel
1
2
MAINS ON
BACK LEFT
FRONT LEFT
FRONT RIGHT
BACK RIGHT
OVEN FUNCTION
TEMPERATURE
OVEN PROGRAMMER
A
U
T
O
THERMOSTAT
TIMER
IGNITION
3
1.
2.
3.
4.
5.
4
5
6
7
Cooker Operation Pilot Light
Oven Thermostat Pilot Light
Electric Ignition push button
Back left burner control knob (semi-rapid)
Front left burner control knob (ultra-rapid)
The Oven Cavity
Grill element
8
9
6. Front right burner control knob (auxiliary)
7. Back right burner control knob (semi-rapid)
8. Oven function control knob
9. Oven Thermostat control knob
10. 24 hour clock and programmer
Accessories
Oven Light
Grill/roasting pan
Grill trivet
Removable
handles
Oven fan
Fitting the Splash back
A stainless steel splash back is supplied with the
appliance. This is meant to be fitted on the rear edge of
the cooker's hob. The splash back package is in the oven
cavity.
1. Unpack the splash back and dispose of the packaging
with due regard to safety and the environment.
2. Slide the two bayonets of the splash back into the
relevant supports on the rear adge of the cooker's
hob.
4
10
Using the Hob
Hob burners
F
l
l
l
l
To light a burner:
Push the electric ignition button which is marked with
a little spark ( ).
At the same time, push in and turn the relevant control
knob anticlockwise to maximum position.
Then adjust the flame as required.
If the burner does not ignite, turn the control knob to
zero, and try again.
FO 2063
When switching on the mains, after installation or
a power cut, it is quite normal for the spark
generator to be activated automatically.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
Burner
Ultra-rapid
(triple crown)
Medium (semi-rapid)
Small (Auxiliary)
minimum
diameter
220 mm.
120 mm.
80 mm.
maximum
diameter
260 mm.
220 mm.
160 mm.
If you use a saucepan which is smaller than the
recommended size, the flame will spread beyond
the bottom of the vessel, causing the handle to
overheat.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
If the control knobs become difficult to turn, please
contact your local Service Centre.
Semi-rapid and auxiliary burners:
A) Burner Cap
B) Burner Crown
C) Ignition Candle
Special grid
When using the auxiliary burner (with pans having
a diameter equal or higher than 50mm), place the
special grid on the pan support, as shown in the
diagram.
Triple-crown burner
Always ignite the burner before putting the
pans on.
If after a few attempts the burner does not ignite,
check that the burner cap and crown are correctly
positioned (see diagram).
Triple crown (ultra-rapid) burner
5
Before the First Use of the Oven
Remove all packaging, both inside and outside
the oven, before using the oven.
Before first use, the oven should be heated without food.
During this time, an unpleasant odour may be emitted.
This is quite normal.
F
l
l
Set the electronic programmer to manual
function.
Switch the oven function control knob to
conventional cooking
.
Set the thermostat control knob to MAX.
l
Open a window for ventilation.
l
Allow the oven to run empty for approximately
45 minutes.
This procedure should be repeated with the fan cooking
and grill function for approximately 5-10 minutes.
l
Using the Oven
Oven Function Control Knob
Conventional cooking - The heat comes from
0
both the top and bottom element, ensuring even
heating inside the oven.
Bottom heating element - The heat comes from
the bottom of the oven only
Top heating element - The heat comes from the
top of the oven only
Grill - The heat comes only from the top element
Fan cooking - This function allows you to
roast or roast and bake simultaneously using
any shelf.
FO 2542
Defrost setting - This function assists in
50
thawing of frozen food.
Thermostat Control Light
The thermostat control light will come on when the
thermostat control knob is turned. The light will remain on
until the correct temperature is reached. It will then cycle
on and off to show the temperature is being maintained.
6
150
The mains on light will come on when the oven function
control knob is set.
FO 0877
0
Mains On Light
20
Turn the thermostat control knob clockwise to select
temperatures between 50°C and 250°C (MAX).
100
Thermostat Control Knob
24 hour Clock and Timer
Cookpot
symbol
Minute minder
Cooking duration
End of cooking time
Auto
symbol
Manual function
A
U
T
O
TIMER
Cookpot symbol - This will be displayed when a
program is in operation.
Time
setting
Auto symbol - This will be displayed when the
oven has been programmed for automatic
operation.
A
U
T
O
Programming
controls
Time setting knob - Turn it clockwise and hold it in
the turned position to increase the time setting.
Turn it anticlockwise and hold it in the turned
position to decrease the time setting. The countup or count-down speed increases the longer the
knob is held in the turned position.
The electronic timer can indicate the time of day, operate
as a minute minder and automatically operate the oven.
Before the oven can be operated, the time of day must
be set on the electronic timer.
Please note that this is a 24 hour clock. For example,
2pm is shown as 14:00.
TIMER
In case of loss of power, all the settings (time of
day, set program or program in operation), will be
cancelled. When the power is restored, the
numbers on the display will flash, and the timer
has to be reset.
F
TO SET THE TIME OF DAY
Press button , release the button, then turn the time
setting knob until the correct time of day is displayed.
F
TIMER
TO SET THE MINUTE MINDER
Press button
, release the button, then turn the setting
time knob until the duration time is displayed (maximum
23 hours, 59 minutes).
Our diagram shows the timer set for 45 minutes. After a
few seconds the time of day will show in the display.
To check the number of minutes remaining, press the
button. At the end of the timed period an alarm will
sound. To switch off the alarm press button
.
7
F
MANUAL FUNCTION
Press button
to set the oven for manual function.
TIMER
F
TO SET THE TIMER TO SWITCH OFF
ONLY
This is useful if you want to begin cooking immediately
but have the oven switch off automatically.
1. Set the oven function control knob and the thermostat
control knob on the required settings.
2. Place food in the oven.
3. Press button
, release the button, then turn the
time setting knob until the required cooking duration
is displayed.
Our diagram shows the timer set for 30 minutes.
At the end of the cooking time the oven will switch off, an
alarm will sound. To switch off the alarm press button .
Ensure the oven function control knob and
the thermostat control knob are in the OFF
position.
F
TIMER
TO SET THE TIMER TO SWITCH
THE OVEN ON AND OFF
1. Ensure the clock is showing the right time of day.
2. Carry out steps 1, 2 and 3 as explained in "To set the
timer to switch off only".
, release the button, then turn the
3. Press button
time setting knob until the end cooking time is
displayed.
Our diagram shows the end cooking time set for
7.00 pm.
4. The oven will switch on and off automatically.
The end of cooking will be marked by an acoustic
alarm. To switch off the alarm press button .
Ensure the oven function control knob and
the thermostat control knob are in the OFF
position.
F
TO CANCEL A PROGRAMME
Press button . Any set programme or programme in
operation will be cancelled and the timer will revert to
manual function.
Ensure the oven function control knob and
the thermostat control knob are in the OFF
position.
8
TIMER
Using the Oven
• Always cook with the oven door closed.
•
Stand clear when opening the drop down
oven door. Do not allow it to fall open support the door using the door handle,
until it is fully open.
•
The oven has four shelf levels, and is supplied
with two shelves.
•
The shelf positions are counted from the
bottom of the oven as shown in the diagram.
•
It is important that these shelves are correctly
positioned as shown in the diagram.
Do not place cookware directly on the oven
base.
•
4
3
2
1
Hints and Tips
Condensation and steam
When food is heated it produces steam in the same way
as a boiling kettle. The oven vents allow some of this
steam to escape. However, always stand back from
the oven when opening the oven door to allow any
build up of steam or heat to release.
If the steam comes into contact with a cool surface on
the outside of the oven, e.g. a trim, it will condense and
produce water droplets. This is quite normal and is not a
fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
The effects of dishes
on cooking results
Dishes and tins vary in their thickness, conductivity,
colour, etc. which affects the way they transmit heat to
the food inside them.
A Aluminium, earthenware, oven glassware and bright
shiny utensils reduce cooking and base browning.
B Enamelled cast iron, anodized aluminium, aluminium
with non-stick interior and coloured exterior and dark,
heavy utensils increase cooking and base browning.
Cookware
•
•
•
Use any oven proof cookware which will withstand
temperatures of 250°C.
Baking trays, oven dishes, etc. should not be placed
directly against the grid covering the fan at the back
of the oven, or placed on the oven base.
Do not use baking trays larger than 30 cm x 35 cm
(12 in x 14 in) as they will restrict the circulation of
heat and may affect performance.
Storage Drawer
The storage drawer is located underneath the oven cavity.
During cooking the storage drawer may become
hot if the oven is on high for a long period of time,
therefore flammable materials such as oven gloves,
tea towels, plastic aprons etc. should not be
stored in the drawer.
Oven accessories such as baking sheets, will
also become hot, therefore care should be taken
when removing these items from the drawer whilst
the oven is in use or still hot.
9
Using the Conventional Oven
When using this setting, heat comes from both the top
and bottom elements. This allows you to cook on a single
level and is particularly suitable for dishes which require
extra base browning such as pizzas, quiches and flans.
Gratins, lasagnes and hotpots which require extra top
browning also cook well in the conventional oven. This
form of cooking gives you the opportunity to cook without
the fan in operation.
to Use the
F How
Conventional Oven
1. Turn the oven function control knob to the required
cooking function ( ).
2. Turn the thermostat control to the required temperature.
Top oven element only
This function is suitable for finishing cooked dishes, e.g.
lasagne, shepherds pie, cauliflower cheese etc.
Bottom oven element only
This function is particularly useful when blind-baking
pastry. It may also be used to finish off quiches or flans
to ensure the base pastry is cooked through.
THINGS TO NOTE
l
The oven light will come on when the oven function
control knob is set.
l
The thermostat control light will remain on until the
correct temperature is reached. It will then cycle on
and off to show that temperature is being maintained.
10
Hints and Tips
The middle shelf position allows for the best heat
distribution. To increase base browning simply lower the
shelf position. To increase top browning, raise the shelf
position.
The material and finish of the baking trays and dishes
used will affect base browning. Enamelware, dark, heavy
or non-stick utensils increase base browning, while oven
glassware, shiny aluminium or polished steel trays reflect
the heat away and give less base browning.
Always place dishes centrally on the shelf to ensure even
browning.
Stand dishes on suitably sized baking trays to prevent
spillage onto the base of the oven and make cleaning
easier.
Do not place dishes, tins or baking trays directly on the
oven base as it becomes very hot and damage will occur.
For faster preheating use the fan oven function to preheat
the oven until the oven indicator neon goes out, then
swich the selector to the conventional oven setting.
Single level cooking gives best results. If you
require more than one level cooking use the fan
oven function.
Cooking Chart - Conventional Oven
These charts are intended as a guide only. It may be necessary to increase or decrease the temperature to suit your
individual requirements. Only experience will enable you to determine the correct setting for your personal requirements.
Food
Temperature (°C)
Runner
Positions
Cooking
Time (mins)
Biscuits
170-200
2
25-30
Bread, buns, yeast, doughs
200-230
2
35-45
Casseroles
140-170
1-2
90-180
Cakes - small, Queen Victoria sponge
170-190
1-2
18-25
Cakes - madeira, rich fruit
130-180
2
90-150
Choux pastry, eclairs
200-230
2
30-35
Fish
200-230
2
20-40
Fruit pies, plate tarts, crumbles
180-210
2
50-65
Meringues
90-100
2
90-150
Milk puddings
140-160
2
90-150
Pate, terrine (in baine-marie)
160-180
1-2
60-90
Pizzas
200-230
1-2
25-30
Puff pastry, sausage rolls, vol-au-vents
230-250
2
15-25
Quiches, flans
170-200
1-2
50-60
Scones
230-250
2
8-12
Souffle
200-230
2
35-45
Stuffed vegetables
230-250
2
Roast meat & poultry
180-200
2
Yorkshire pudding
200-230
2
Keep food warm, heat dishes
90-100
2
Meat and Poultry Roasting Chart
(Conventional Oven + Fan Oven)
Meat
Cooking Time
35-45
see meat + poultry
roasting chart
40-50
When roasting, ensure the meat is
cooked thoroughly, use a meat
thermometer if preferred to check the
centre temperature has reached the
required temperature (see table
below).
Beef
20-35 mins per 1/2kg (lb) + 20-35 mins
Beef, boned
25-35 mins per 1/2kg (lb) + 25-35 mins
Mutton and Lamb
25-35 mins per 1/2kg (lb) + 25-35 mins
MEAT
TEMPERATURES
Pork and Veal
30-40 mins per 1/2kg (lb) + 30-40 mins
Beef
Ham
30-40 mins per 1/2kg (lb) + 30-40 mins
Chicken
15-20 mins per 1/2kg (lb) + 20 mins
Rare - 60°C
Medium - 70°C
Well Done - 80°C
Turkey and Goose
15-20 mins per 1/2kg (lb) up to 3.5kg (7lb)
Pork
Well Done - 80°C
+ 15 mins per 1/2kg over 3.5kg (7lb)
Lamb
Medium - 70°C
Well Done - 80°C
Duck
25-35 mins per 1/2kg (lb) + 20 mins
11
The Fan Oven
The air inside the oven is heated by the element around
the fan situated behind the back panel. The fan circulates
hot air to maintain an even temperature inside the oven.
The advantages of cooking with this function are:
l
l
l
Faster Preheating
As the fan oven quickly reaches temperature, it is not
usually necessary to preheat the oven although you
may find that you need to allow an extra 5-7 minutes
on cooking times. For recipes which require higher
temperatures, best results are achieved if the oven
is preheated first, e.g. bread, pastries, scones,
souffles, etc.
Lower Temperatures
Fan oven cooking generally requires lower
temperatures than conventional cooking.
Follow the temperatures recommended in the
cooking chart. Remember to reduce temperatures by
about 20-25°C for your own recipes which use
conventional cooking.
Even Heating for Baking
The fan oven has uniform heating on all shelf
positions. This means that batches of the same food
can be cooked in the oven at the same time.
However, the top shelf may brown slightly quicker
than the lower one.
This is quite usual. There is no mixing of flavours
between dishes.
F How to Use the Fan Oven
1. Turn the oven function control knob to
.
2. Turn the thermostat control to the required temperature.
THINGS TO NOTE
l
The oven light will come on when the oven function
control knob is set.
l
The thermostat control light will remain on until the
correct temperature is reached. It will then cycle on
and off to show that temperature is being
maintained.
Hints and Tips
-
-
12
Shelf positions are not critical, but make sure the
shelves are evenly spaced.
When cooking more than one dish in the fan oven,
place dishes centrally on the shelves rather than
several dishes on one shelf.
When the oven is full, you may need to allow slightly
longer cooking time.
When the oven is full of the same food, e.g. equal
trays of small cakes or equal size victoria sandwich
cakes, then they will be cooked in the same time
and removed from the oven together. When different
sizes of trays or types of food, e.g. biscuits and cakes
are cooked, they will not necessarily be ready
together.
-
-
-
-
The fan oven can be used to heat foods through without
thawing first, e.g. fruit tarts, mince pies, sausage rolls,
and other small pastry items. Use a temperature of
190-200°C and allow 20-40 minutes (depending on
the quantity of food in the oven).
The use of too high temperatures can cause uneven
browning. Check with the recommendations for oven
temperatures given in the cooking charts, but be
prepared to adjust the temperature, if necessary.
Remember to reduce temperatures by about 20-25°C
for your own conventional recipes.
When roasting do use the trivet in the meat tin. Fat
and meat juices will drain into the meat tin below and
can be used to make gravy. The trivet also prevents
splashes of fat from soiling the oven interior.
The meat tin should not be placed on a heated
hotplate as this may cause the enamel to crack.
Fan Cooking Chart
This chart is intended as a guide only. It may be
necessary to increase or decrease the temperature to
suit your individual requirements. Only experience will
enable you to determine the correct setting for your
personal requirements.
Food
Shelf
Position
Biscuits
Bread
Casseroles
Cakes:
- Small and queen
- Sponges
- Madeira
- Rich Fruit
- Christmas
- Meringues
Fish
Fruit Pies and Crumbles
Milk Puddings
Pastry:
- Choux
- Shortcrust
- Flaky
- Puff
Plate Tarts
Quiches/Flans
Scones
Roasting:
Meat & Poultry
}
Cooking
Temp (°C)
180 - 190
210 - 220
130 - 140
Shelf positions
are not critical
but ensure that
oven shelves
are evenly
spaced when
more than one
is used.
160-170
160 - 170
140 - 150
130 - 140
130 - 140
90 - 100
170 - 190
190 - 200
130 - 140
190 - 200
180
170 - 180
210 - 220
160 - 180
Defrosting
The oven fan operates without heat and circulates the
air, at room temperature, inside the oven. This increases
the speed of defrosting. However, please note that the
temperature of the kitchen will influence the speed of
defrosting.
This function is particularly suitable for delicate food which
could be damaged by heat, e.g. cream filled gateaux,
iced cakes, pastries, bread and other yeast products.
F
•
•
•
•
How to Use Defrosting
1. Turn the oven function control knob to
Hints and Tips
.
2. Ensure the thermostat control knob is in the OFF
position.
Cover food with a lid, aluminium foil or plastic film to
prevent drying out during defrosting.
ALWAYS COOK THOROUGHLY IMMEDIATELY
AFTER THAWING.
Frozen food should be placed in a single layer when
ever possible and turned over half way through the
defrosting process.
Only joints of meat and poultry up to 2 kg. (4 lb.) are
suitable for defrosting in this way.
Refer to the following table for approximate defrosting
times.
Defrosting Chart
Defrosting time
(Mins)
Standing time
(Mins)
Chicken 1000 g.
100-140
20-30
Place the chicken on an inverted saucer on a large
plate. Defrost open and turn at half time or defrost
covered with foil. Remove giblets as soon as possible.
Meat 1000 g.
100-140
20-30
Defrost open and turn at half time or cover with foil
Meat 500 g.
90-120
20-30
As above
Trout 150 g.
23-35
10-15
Defrost open
Strawberries 300 g.
30-40
10-20
Defrost open
Butter 250 g.
30-40
10-15
Defrost open
Cream 2 x 200 g.
80-100
10-15
Defrost open (cream is easy to whip even if parts of
it are still slightly frozen)
60
60
Food
Cake 1400 g.
Notes
Defrost open
The times quoted in the chart should be used as a guide only, as the speed of defrosting will depend on the kitchen
temperature. For example, the colder the ambient temperature, the longer the defrosting time.
13
Grilling
Grilling must be carried out with the oven door
closed. The grill pan handles must be removed
from the pan.
F How to Use the Grill
1. Turn the oven control function knob to
.
2. Turn the thermostat control knob on the required
temperature.
3. Adjust the grid and grill pan runner position to allow
for different thicknesses of food. Position the food
close to the element for faster cooking and further
away for more gentle cooking.
Preheat the grill on a full setting for a few minutes before
sealing steaks or toasting. Adjust the heat setting and
the shelf as necessary during cooking.
Cooking chart
Cooking time depends on the thickness of the meat and
not on its weight.
Type of food
Bacon rashers
Chicken joints
Gammon rashers
Lamb chops
Pork chops
Sausages (turning as required)
Steaks (average thickness)
Toast
During cooking, the thermostat control light will operate
in the same way as described for the fan oven function.
Hints and Tips
-
-
-
Most foods should be placed on the grid in the grill
pan to allow maximum circulation of air to lift the food
out of the fats and juices. Food such as fish, liver and
kidneys may be placed directly on the grill pan, if
preferred.
Food should be thoroughly dried before grilling to
minimise splashing. Brush lean meats and fish lightly
with a little oil or melted butter to keep them moist
during cooking.
Accompaniments such as tomatoes and mushrooms
may be placed underneath the grid when grilling meats
When toasting bread, we suggest that the top runner
position is used.
The food should be turned over during cooking, as
required.
The grill element is controlled by the thermostat.
During cooking, the grill cycles on and off to
prevent overheating.
14
OI L
Mins per side
2-5
15 - 20
5-8
6 - 12
10 - 15
10 - 12
Rare
3-6
Medium
6 - 10
Well done 8 - 12
1 - 11/2
Maintenance and Cleaning
Before any maintenance or cleaning can be carried
out, you must DISCONNECT the cooker from the
electricity supply.
The Hob Top
The hob is best cleaned whilst it is still warm, as spillage
can be removed more easily than if it is left to cool.
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little wasing up liquid
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.
Pan Supports
The hob has cast iron pan supports. Take care when
removing them. They are fairly heavy and could damage
the hob or your kitchen furniture if you let them fall down.
Wash the pan supports using hot soapy water. If
necessary, a paste cleaner or a soap impregnated steel
wool pad can be used with caution.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burners caps and crowns using hot soapy
water, and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
15
Cleaning the Oven
The oven should be kept clean at all times. A
build-up of fats or other foodstuffs could result in
a fire, especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your oven, check
that they are suitable and that their use is recommended
by the manufacturer.
Cleaners that contain bleach should NOT be used as
they may dull the surface finishes. Harsh abrasives should
also be avoided.
External cleaning
Regularly wipe over the control panel, oven door and door
seal using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
To prevent damaging or weakening the door glass
panels avoid the use of the following:
•
•
Household detergent and bleaches
Impregnated pads unsuitable for non-stick
saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Clean the outer and inner door glass using warm soapy
water. Should the inner door glass become heavily soiled
it is recommended that a cleaning product such as Hob
Brite, or Bar Keepers Friend is used.
DO NOT clean the oven door while the glass
panels are warm. If this precaution is not
observed the glass panel may shatter.
If the door glass panel becomes chipped or has
deep scratches, the glass will be weakened and
must be replaced to prevent the possibility of the
panel shattering. Contact your local Service Centre
who will be pleased to advise further.
Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm.
Wipe the oven over with a soft cloth soaked in warm
soapy water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
If the soilage has become set, after the oven has cooled
down, the following process will help to soften the
splatters to help make cleaning easier.
F
1. Place the grill/ meat pan on the oven shelf
positioned in the lowest runner.
2. Add a few drops of washing-up liquid to the
pan and fill to about 12 mm. with boiling water
from the kettle.
3. Close the oven door, turn the oven function knob
on fan oven
on 50°C.
4. After 15 minutes, turn off the thermostat and
allow the fan oven to continue without heat for
a further 5 minutes, when the temperature of
the water will have cooled down.
5. Carefully remove the pan of water from the oven
and use normal oven cleaners to clean away
soil residues.
6. Leave a little of the soapy water to soak into
any burned on spillage on the floor of the oven
for a longer time if necessary.
Oven Shelves
To clean the oven shelves, soak in warm soapy water
and remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
Oven lamp replacement
Disconnect the appliance.
Unscrew the lamp and substitute it with another suitable
for higher temperature (300°C) having the following
characteristics:
Voltage:
230-240V (50Hz)
Power:
15W
Connection:
E14
FO 0287
16
and set the thermostat knob
Something Not Working
If the appliance is not working correctly, please carry out the following checks, before contacting your local Service
Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,
a charge will be made even if the appliance is under guarantee.
SOLUTION
SYMPTOM
n There is no spark when lighting the gas
u Check that the unit is plugged in and the electrical
n The gas ring burns unevenly
u Check the main jet is not blocked and the burner
supply is switched on
u Check that the RCCB has not tripped (if fitted)
u Check the mains fuse has not blown
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
crown is clear of food particles.
u Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
n The oven does not come on
u Check a cooking function / temperature have been
selected.
u Check the socket switch or the switch from the
mains supply to the oven is ON.
n The oven light does not come on
n The timer does not work
n It takes too long to finish the dishes, or they are
cooked too fast.
n Steam and condensation settle on the food and the
oven cavity.
u Check the light bulb, and replace it if necessary
(see "Oven Light Replacement")
u Check the instructions for the timer
u The temperature may need adjusting
u Refer to the contents of this booklet, especially to
the chapter “Using the Oven”.
u Leave dishes inside the oven no longer than 15-20
minutes after the cooking is completed.
If after all these checks, the cooker still does not work, contact your local Service Force Centre.
Service and Spare Parts
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or
guarantee documentation is required for inguarantee service calls.
17
Customer Care Department
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone at the address below or visit our website at
www.zanussi.co.uk
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
Zanussi Guarantee conditions
We, Zanussi, undertake that if, within 12 months of the
date of the purchase, this Zanussi appliance or any part
thereof is proved to be defective by any reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE for
labour, materials or carriage on condition that:
*
The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
* All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours, in which case a premium will be charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
18
*
*
Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
Products of Zanussi manufacture which are not
marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European Community
(EC) or European Free Trade Area.
* The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone
Stockholm
Slough
+33 (0) 3 44 62 29 29
+49 (0) 800 234 7378
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 1753 219897
Instructions for the Installer
Technical Data
Appliance Class 2 sub class 1 and Class 1
APPLIANCE CATEGORY:
II 2H3+
APPLIANCE GAS SUPPLY: Natural gas G20 20mbar
Oven
Dimensions
Bottom heating element
1,045 W
Oven element
1,880 W
Grill Element
1,830 W
Convection heating element
2,090 W
Height
Depth
Width
Oven Capacity
Top heating element
900 mm
600 mm
600 mm
1.8 Cu. ft
Hob
VALUE = 37.78 MJ/m3
CHARACTERISTICS
Ws - 50.7 MJ/ m3
VALUE = 49.92 MJ/Kg
LPG GAS
28-30/37 mbar
NATURAL GAS
20 mbar
TYPE OF
GAS
Rear right burner (semi-rapid)
Front right burner (auxiliary)
Rear left burner (semi-rapid)
Front left burner (ultra-rapid)
BURNER
POSITION
ULTRA-RAPID
(large)
Convection fan
30 W
Oven light
15 W
Total rating
2,000 W
1,000 W
2,000 W
3,500 W
2,135 W
Supply voltage (50 Hz)
SEMI-RAPID
(medium)
MIN
MAX
MIN
MAX
MIN
3.5
1.2
2.0
0.45
1.0
0.33
0.333
0.114
0.190
0.043
0.095
0.031
136
Adjust.
96
Adjust.
70
Adjust.
NOMINAL THERMAL
POWER kW
3.5
1.2
2.0
0.45
1.0
0.33
NOMINAL FLOW
RATE
g/h
252
86.5
144
32
72
24
93
56
71
32
50
28
NOMINAL FLOW
RATE m3/h
NOZZLE REFERENCE
1/100 mm
NOZZLE REFERENCE
1/100 mm
230-240 V
AUXILIARY
(small)
MAX
NOMINAL THERMAL
POWER kW
835 W
Important Safety Requirements
This appliance must be installed in accordance with the
Gas Safety (Installation and Use) Regulations (current
addition) and the I.E.E. Wiring Regulations. Detailed
recommendations are contained in the following British
Standard Codes of Practice - B.S. 6172, B.S. 5440: Part
2 and B.S. 6891: Current Editions.
Provision for Ventilation
The room containing the cooker should have an air supply
in accordance with B.S. 5440: Part 2: Current Editions.
The following requirements for ventilation must be met.
The cooker should not be installed in a bed sitting room
with a volume of less than 20m3, if it is installed in a
room of volume less 5m3 an air vent of effective area of
110cm2 is required; if it is installed in a room of volume
between 5m3 and 10m3, an air vent of effective area 50cm2
is required, while if the volume exceeds 11m3 no air vent
is required. However, if the room has a door which opens
directly to the outside, no air vent is required even when
the volume is between 5m3 and 11m3.
19
If there are other fuel burning appliances in the same
room, B.S. 5440: Part. 2: Current Editions should be
consulted to determine the requisite air vent
requirements.
Location
The cooker may be located in a kitchen, a kitchen/diner
or bedsitting room but not in a bathroom, shower room
or garage.
For information regarding the fitting of flexible supply
pipes, the highest temperature at the rear of this cooker
which may come into contact with the supply pipe is
70°C above ambient.
When the appliance has been installed there must be
enough space fot the hotplate lid (when present) to open
fully.
Positioning the Cooker
Caution:
Some soft or badly fitted floor coverings can be damaged
when the cooker is moved across their surface for
cleaning. It is advisable to ensure that the floor covering
in the area below the cooker is either securely fixed so
as not to ruck up when the cooker is moved or, if
preferred, removed.
Installation
1. Positioning the Appliance (Fig. 1)
D
420
115
780
C
Note A:
The appliance is designed to be flush fitted with 2mm
clearance at each side to allow for it to be pulled forward
for cleaning etc.
E
B
A
FO 1141
Dimensions are given in millimeters
Fig. 1
The appliance must be installed in accordance to the
type X (standard EN 60335-2-6).
Therefore the appliance cannot be installed beside
furniture higher than the cooker worktop.
This cooker must only be installed by qualified
personnel, according to the manufacturer’s instructions
and to the relevant British Standards.
20
Note B:
The hotplate side trims should be flush with the cabinets
and must not be below. Adjustable levelling feet at the
front and rear are provided on the base of the appliance.
Adjustment is obtained by rotating in or out, the feet at
the front or rear of the appliance from the underside of
the appliance, with the drawer removed.
A spirit level should be placed on a cake tray on one of
the shelves to confirm that the appliance is correctly
levelled.
The levelling feet fitted to the appliance will achieve a
height to hotplate trims of 900mm-0 + 10.
Note C:
If the appliance is fitted next to a side wall or cabinets
above height of the hotplate trims, then a gap of 115 mm
is required.
Curtains must not be fitted immediately behind the
cooker or within 115 mm of the sides of the cooker.
Note D:
Any wall cabinet or extractor must not be lower than
780mm above hotplate level.
Note E:
Wall cabinets may be fitted in line with the sides of the
base units, providing that the lower edge of the wall
cabinet is a minimum of 420mm above the worktop.
300 mm.
WALL FACE
100 mm.
580 mm.
BACK OF COOKER
ENGAGEMENT EDGE FOR
STABILITY BRACKET
LEVELLING FEET
BASE OF COOKER
A
PENCIL LINE ON THE FLOOR
295 mm.
FO 0179
SIDE VIEW
OF THE COOKER
PLAN VIEW OF THE COOKER
Fig. 2
Dimensions are given in millimeters
Fitting the Stability Bracket
(Not supplied)
Connecting to Gas
If the cooker has to be installed with a flexible supply
pipe, it is necessary that a stability device is fitted.
(See safety Requirements: Page 19).
If a stability bracket is to be fitted by the installer, these
instructions should be read in conjunction with the leaflet
packed with the stability bracket.
Place cooker in its intended position and level cooker.
Mark off 295 mm (11 1/2") from the right hand side of the
cooker as shown, this is the centre line of the bracket
fixing.
Draw a line 100mm (4") from the front edge of the
levelling feet (see Fig. 2) and remove cooker from its
position. Mark off 580mm (23") back from this line on
the centre line of the bracket to locate the front edge of
the lower bracket.
This cooker is designed to be installed with an appliance
flexible connection. Connection is made to the RC 1/2
(1/2" B.S.P.) threaded entry pipe located just below the
hotplate level on the rear right-hand side of the cooker.
Check for gas soundness after connecting the gas
supply.
The gas bayonet connector must be fitted in the shaded
area indicated in the diagram. Take into account that it
must be possible to pull the cooker forward sufficiently.
The hose must not get caught on the stability bracket.
Note:
For certain types of gas bayonet connection used, it
may not be possible for the appliance to be pushed fully
back to the wall stops.
Important:
Flexible tubing MUST comply with BS.669 Current
Edition.
Fix lower bracket (with two fixing holes) to the floor, then
measure height from floor level to engagement edge on
back of cooker, dimension 'A' of Fig. 2.
Assemble upper bracket to lower bracket so that
underside of bracket is dimension 'A' +3mm (1/8") above
floor level. Re-position cooker and check that top bracket
engages into cooker back to a depth of 75mm (3"), as
shown in Fig. 2.
Should the stability bracket currently installed not allow
the cooker to stand correctly, ask the installer to replace
it with the correct type.
600
450
130
FO 2435
Fig. 3
Dimensions are given in millimeters
21
Electrical connections
Any electrical work required to install this cooker
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS COOKER MUST BE EARTHED.
Permanent Connection
The manufacturer declines any liability should these
safety measures not be observed.
In the case of a permanent connection, it is necessary
that you install a double pole switch between the cooker
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
This cooker is designed to be connected to a 230240V 50Hz AC electrical supply.
The switch must not break the yellow and green earth
cable at any point.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the cooker rating
plate. The rating plate is located on the oven frame.
Ensure that the cooker supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.
The cooker is supplied with a 3 core flexible supply cord
incorporating a 13amp plug fitted. In the event of having
to change the fuse, a 13amp ASTA approved (BS 1362)
fuse must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
F
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
the letter 'E' or the earth symbol
or coloured
green and yellow.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
1
NOTE: The earth wire should be about 2 cm. longer
than the live and neutral wires.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard. Ensure that
the cut off plug is disposed of safely.
FO 0390
22
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
-
Turn the gas tap to the MAX position and ignite.
-
Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
F
-
-
Re-ignite the burner and set to MIN.
Remove the control knob.
The adjustment screw is located down the centre of
the gas tap control shaft or on the lower right hand
side of the shaft (see diagram).
To adjust, use a thin bladed screwdriver and turn the
adjustment screw until the flame is steady and does
not extinguish, when the knob is turned from MIN to
MAX. Repeat this procedure for all burners.
F
-
a
Procedure:
FO 1032
a) Minimum adjustment screw
b) Tap
Pressure Testing
Remove pan support and front left burner cap and
crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite another burner
supply.
The pressure reading should be nominally 20mbar
and must be between 17 mbar and 25mbar.
Turn off the burner supplies.
Conversion from Natural to LPG Gas
IMPORTANT
The replacement/conversion of the gas hob should
only be undertaken by a CORGI registered engineer.
It is important to note that this model is designed for use
with natural gas but can be converted for use with butane
or propane gas providing the correct injectors are fitted.
The gas rate is adjusted to suit.
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten clockwise the by pass screw. Upon completion
stick the replacement rating plate near the gas supply
pipe.
Method
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electricity supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors (see Table: page 19).
23
Grafiche MDM - Forlì
CUSTOMER CARE
Zanussi
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: 08705 727727
© Electrolux Household Appliances Limited 2002
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
35675-4802
02/02