User’s Guide [Copy Operations]
Table of contents
1
2
3
4
Introduction
1.1
1.1.1
1.1.2
1.2
1.2.1
Welcome .......................................................................................................................................... 1-2
User's guides ..................................................................................................................................... 1-2
User's Guide ...................................................................................................................................... 1-3
Conventions used in this manual .................................................................................................. 1-4
Symbols used in this manual ............................................................................................................. 1-4
To use this machine safely................................................................................................................. 1-4
Procedural instruction........................................................................................................................ 1-4
Key symbols....................................................................................................................................... 1-5
1.2.2
Original and paper indications ........................................................................................................... 1-5
Original and paper sizes .................................................................................................................... 1-5
Original and paper indications ........................................................................................................... 1-5
Part names and their functions
2.1
2.1.1
2.1.2
2.2
2.2.1
2.2.2
2.2.3
Options............................................................................................................................................. 2-2
bizhub C652/C652DS/C552/C552DS................................................................................................ 2-2
bizhub C452....................................................................................................................................... 2-5
Main Body ........................................................................................................................................ 2-7
Outside of the main body (front) ........................................................................................................ 2-7
Outside of the main body (rear) ......................................................................................................... 2-9
Main bodyInside............................................................................................................................... 2-11
bizhub C652/C552/C452 ................................................................................................................. 2-11
bizhub C652DS/C552DS ................................................................................................................. 2-13
2.2.4
Control panel.................................................................................................................................... 2-14
Adjusting the angle of the control panel .......................................................................................... 2-15
2.2.5
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
Touch panel ..................................................................................................................................... 2-16
Option............................................................................................................................................. 2-18
Finisher FS-526/Saddle stitcher SD-508/Punch kit PK-516............................................................ 2-18
Job separator JS-602 ...................................................................................................................... 2-20
Z Folding Unit ZU-606 ..................................................................................................................... 2-21
Post Inserter PI-505 ......................................................................................................................... 2-22
Finisher FS-527/ Saddle Stitcher SD-509/ Punch Kit PK-517/ Job Separator JS-603 ................... 2-23
Job Separator JS-504...................................................................................................................... 2-25
Large capacity unit LU-301/LU-204 ................................................................................................ 2-26
Using this machine
3.1
3.2
3.2.1
Turning on or off the machine ....................................................................................................... 3-2
Basic copy operations .................................................................................................................... 3-4
Placing originals ................................................................................................................................. 3-4
Loading the original into the ADF ...................................................................................................... 3-4
Placing the original on the original glass ........................................................................................... 3-5
3.2.2
3.2.3
Basic copy operations ....................................................................................................................... 3-5
Copy operations using multiple functions ......................................................................................... 3-6
Functions that cannot be combined .................................................................................................. 3-8
Control Panel Keys
Control panel and functions............................................................................................................... 4-2
4.1
About the [Start] key, the [Stop] key, and the [Interrupt] key..................................................... 4-4
The [Start] key .................................................................................................................................... 4-4
The [Stop] key .................................................................................................................................... 4-4
bizhub C652/C652DS/C552/C552DS/C452
Contents-1
The [Interrupt] key .............................................................................................................................. 4-4
The [Reset] key .................................................................................................................................. 4-4
5
4.2
About the [Copy] key, the [Fax/Scan] key, and the [User Box] key ........................................... 4-5
The [Copy] key ................................................................................................................................... 4-5
The [Fax/Scan] key ............................................................................................................................ 4-5
The [User Box] key............................................................................................................................. 4-5
4.3
4.4
4.5
The [Utility/Counter] key ................................................................................................................ 4-6
The [Mode Memory] key................................................................................................................. 4-7
The [Access] key ............................................................................................................................. 4-8
Controlling access to the machine by user/account (user authentication/account track)................. 4-8
Using the machine during non-scheduled hours............................................................................. 4-10
4.6
4.7
4.8
4.9
4.10
4.11
The [Power Save] key ................................................................................................................... 4-11
The [Accessibility] key.................................................................................................................. 4-12
The [Enlarge Display] key............................................................................................................. 4-14
The [Guidance] key ....................................................................................................................... 4-15
The [C] (Clear) key ........................................................................................................................ 4-17
The [Proof Copy] key .................................................................................................................... 4-18
Printing one set to check the copy result (Proof Copy) ................................................................... 4-18
Using a preview image to check the copy result (Advanced Preview) ............................................ 4-19
Copy Function
5.1
5.1.1
5.1.2
Basic................................................................................................................................................. 5-3
Color .................................................................................................................................................. 5-4
Paper.................................................................................................................................................. 5-5
Configuring a custom size ................................................................................................................. 5-6
Configuring wide paper...................................................................................................................... 5-6
5.1.3
5.1.4
5.1.5
5.1.6
Zoom.................................................................................................................................................. 5-7
Duplex/Combine ................................................................................................................................ 5-8
Finishing........................................................................................................................................... 5-10
Post Inserter..................................................................................................................................... 5-12
Keys on control panel ...................................................................................................................... 5-12
Finishing using Post Inserter............................................................................................................ 5-13
5.1.7
5.1.8
5.2
Separate Scan ................................................................................................................................. 5-13
Auto Rotate OFF .............................................................................................................................. 5-14
Original Setting.............................................................................................................................. 5-15
Copying mixed originals .................................................................................................................. 5-16
Copying Z-folded originals............................................................................................................... 5-17
5.3
5.4
5.4.1
Quality/Density .............................................................................................................................. 5-18
Application..................................................................................................................................... 5-20
Sheet/Cover/Chapter Insert ............................................................................................................. 5-21
OHP Interleave ................................................................................................................................. 5-21
Cover Sheet ..................................................................................................................................... 5-22
Insert Sheet...................................................................................................................................... 5-23
Insert Image ..................................................................................................................................... 5-24
Chapters .......................................................................................................................................... 5-26
Program Jobs .................................................................................................................................. 5-27
5.4.2
Edit Color ......................................................................................................................................... 5-29
Neg./Pos. Reverse ........................................................................................................................... 5-29
Mirror Image..................................................................................................................................... 5-30
Background Color............................................................................................................................ 5-31
Color Adjustment ............................................................................................................................. 5-31
5.4.3
Book Copy/Repeat .......................................................................................................................... 5-33
Book Copy ....................................................................................................................................... 5-33
Image Repeat................................................................................................................................... 5-34
Poster Mode .................................................................................................................................... 5-35
Booklet Original................................................................................................................................ 5-36
5.4.4
5.4.5
Page Margin..................................................................................................................................... 5-37
Image Adjust .................................................................................................................................... 5-39
bizhub C652/C652DS/C552/C552DS/C452
Contents-2
6
5.4.6
5.4.7
Booklet............................................................................................................................................. 5-40
Erase ................................................................................................................................................ 5-41
Frame Erase ..................................................................................................................................... 5-41
Non-Image Area Erase..................................................................................................................... 5-42
5.4.8
Stamp/Composition ......................................................................................................................... 5-43
Date/Time......................................................................................................................................... 5-44
Page Number ................................................................................................................................... 5-45
Stamp............................................................................................................................................... 5-47
Copy Protect.................................................................................................................................... 5-48
Copy Guard...................................................................................................................................... 5-49
Password Copy................................................................................................................................ 5-50
Stamp Repeat .................................................................................................................................. 5-51
Header/Footer.................................................................................................................................. 5-53
Watermark........................................................................................................................................ 5-54
Overlay ............................................................................................................................................. 5-55
Registered Overlay........................................................................................................................... 5-56
5.4.9
5.4.10
5.5
5.5.1
5.5.2
Card Copy........................................................................................................................................ 5-59
Save in User Box ............................................................................................................................. 5-60
Left panel display .......................................................................................................................... 5-61
Job List ............................................................................................................................................ 5-62
Check Job........................................................................................................................................ 5-64
User Settings
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
7
System Settings .............................................................................................................................. 6-3
Custom Display Settings ................................................................................................................ 6-6
Copier Settings................................................................................................................................ 6-8
Fax/Scan Settings ......................................................................................................................... 6-11
Printer Settings ............................................................................................................................. 6-12
Change Password ......................................................................................................................... 6-13
Change E-Mail Address................................................................................................................ 6-14
Change Icon .................................................................................................................................. 6-15
Register Authentication Information........................................................................................... 6-16
Cellular Phone/PDA Setting ......................................................................................................... 6-18
Administrator Settings
7.1
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
7.1.7
System Settings .............................................................................................................................. 7-3
Power Save Settings.......................................................................................................................... 7-3
Output Settings .................................................................................................................................. 7-4
Date/Time Settings ............................................................................................................................ 7-5
Daylight Saving Time ......................................................................................................................... 7-6
Weekly Timer Setting ......................................................................................................................... 7-7
Restrict User Access.......................................................................................................................... 7-8
Expert Adjustment ............................................................................................................................. 7-9
Leading Edge Adjustment................................................................................................................ 7-13
Centering.......................................................................................................................................... 7-13
Media Adjustment ............................................................................................................................ 7-14
Center Staple Position ..................................................................................................................... 7-14
Half-Fold Position ............................................................................................................................ 7-15
Tri-Fold Position Adjustment ........................................................................................................... 7-15
Punch Vertical Position Adjustment................................................................................................. 7-16
Punch Horizontal Position Adjustment ............................................................................................ 7-16
Punch Regist Loop Size Adjustment ............................................................................................... 7-17
Punch Edge Sensor Adjustment ...................................................................................................... 7-17
Vertical Punch (Z-Fold) Position Adjustment ................................................................................... 7-17
Horizontal Punch (Z-Fold) Position Adjustment............................................................................... 7-18
1st Z-Fold Position Adjustment ....................................................................................................... 7-18
2nd Z-Fold Position Adjustment ...................................................................................................... 7-19
Punch Unit Size Detect Sensor........................................................................................................ 7-19
bizhub C652/C652DS/C552/C552DS/C452
Contents-3
Color Registration Adjust ................................................................................................................. 7-20
Gradation Adjustment ...................................................................................................................... 7-21
8
7.1.8
7.1.9
7.1.10
7.1.11
7.1.12
7.1.13
7.1.14
7.1.15
7.1.16
7.1.17
7.2
7.3
7.4
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
7.4.6
7.4.7
7.4.8
7.4.9
7.4.10
7.4.11
7.5
7.6
7.7
7.8
7.9
7.10
7.10.1
7.10.2
7.10.3
7.10.4
7.10.5
List/Counter ..................................................................................................................................... 7-22
Reset Settings.................................................................................................................................. 7-23
User Box Settings ............................................................................................................................ 7-24
Standard Size Setting ...................................................................................................................... 7-24
Stamp Settings ................................................................................................................................ 7-25
Blank Page Print Settings ................................................................................................................ 7-26
Skip Job Operation Settings ............................................................................................................ 7-26
Default Bypass Paper Type Setting ................................................................................................. 7-27
Advanced Preview Setting ............................................................................................................... 7-27
Page Number Print Position............................................................................................................. 7-28
Administrator/Machine Settings.................................................................................................. 7-29
One-Touch/User Box Registration .............................................................................................. 7-30
User Authentication/Account Track............................................................................................ 7-31
General Settings .............................................................................................................................. 7-32
User Authentication Settings ........................................................................................................... 7-34
Account Track Settings.................................................................................................................... 7-37
Print without Authentication............................................................................................................. 7-38
Print Counter List ............................................................................................................................. 7-38
External Server Settings................................................................................................................... 7-39
Limiting Access to Destinations....................................................................................................... 7-39
Authentication Device Settings ........................................................................................................ 7-40
User/Account Common Setting....................................................................................................... 7-41
Scan to Home Settings .................................................................................................................... 7-41
Scan to Authorized Folder Settings ................................................................................................. 7-41
Network Settings .......................................................................................................................... 7-42
Copier Settings.............................................................................................................................. 7-43
Printer Settings ............................................................................................................................. 7-45
Fax Settings ................................................................................................................................... 7-46
System Connection....................................................................................................................... 7-47
Security Settings ........................................................................................................................... 7-49
Administrator Password................................................................................................................... 7-49
User Box Administrator Setting ....................................................................................................... 7-49
Administrator Security Levels .......................................................................................................... 7-50
Security Details ................................................................................................................................ 7-51
Enhanced Security Mode................................................................................................................. 7-54
Required settings ............................................................................................................................. 7-54
Settings to forcibly changed ............................................................................................................ 7-54
7.10.6
7.10.7
7.10.8
7.10.9
7.11
7.12
HDD Settings ................................................................................................................................... 7-55
Function Management Settings ....................................................................................................... 7-56
Stamp Settings ................................................................................................................................ 7-57
Driver Password Encryption Setting ................................................................................................ 7-57
License Settings............................................................................................................................ 7-58
OpenAPI Authentication Management Settings ........................................................................ 7-59
Maintenance
8.1
8.1.1
Paper ................................................................................................................................................ 8-2
Checking the paper............................................................................................................................ 8-2
Replenishment message.................................................................................................................... 8-2
Precautions regarding the use of paper ............................................................................................ 8-2
Paper storage..................................................................................................................................... 8-2
8.1.2
Loading paper .................................................................................................................................... 8-3
Loading paper into trays 1 and 2 ....................................................................................................... 8-3
Loading paper into trays 3 and 4 ....................................................................................................... 8-4
bizhub C652/C652DS/C552/C552DS/C452
Contents-4
Loading paper into the bypass tray ................................................................................................... 8-5
Loading paper into the LCT ............................................................................................................... 8-7
9
10
11
12
8.2
8.2.1
Consumables................................................................................................................................... 8-8
Checking comsumables .................................................................................................................... 8-8
Replacement message ...................................................................................................................... 8-8
Checking consumables status......................................................................................................... 8-10
Viewing counters.............................................................................................................................. 8-10
Checking the total number of pages printed ................................................................................... 8-11
8.3
Cleaning procedure ...................................................................................................................... 8-12
Slit glass (bizhub C652/C552/C452) ................................................................................................ 8-12
Slit glass (front) (bizhub C652DS/C552DS)...................................................................................... 8-12
Slit glass (back) (bizhub C652DS/C552DS) ..................................................................................... 8-13
Original glass, control panel, paper take-up roller........................................................................... 8-13
Housing, document pad .................................................................................................................. 8-14
Troubleshooting
9.1
When the message "Trouble" appears (call a service representative) ...................................... 9-2
Problems that cannot be corrected by the user ................................................................................ 9-2
9.2
Troubleshooting table..................................................................................................................... 9-4
Simple troubleshooting ...................................................................................................................... 9-4
Main messages and their remedies ................................................................................................... 9-8
Icons that appear in the touch-panel screen ................................................................................... 9-10
9.3
If print quality is deteriorated....................................................................................................... 9-12
Cleaning the electrostatic charger wire ........................................................................................... 9-12
Cleaning the print head.................................................................................................................... 9-13
Authentication unit (biometric type)
10.1
10.1.1
10.1.2
Using an authentication unit (biometric type) ............................................................................ 10-2
Configuring this machine ................................................................................................................. 10-3
Registering a user ............................................................................................................................ 10-5
Registering a user using the control panel of this machine ............................................................. 10-5
Registering a user using Data Administrator ................................................................................... 10-6
Checking the version of the installed Data Administrator................................................................ 10-7
Setup................................................................................................................................................ 10-7
User registration............................................................................................................................. 10-11
10.1.3
Logging in to this machine............................................................................................................. 10-17
When 1-to-many authentication has been specified ..................................................................... 10-17
When 1-to-1 authentication has been specified ............................................................................ 10-18
Authentication unit (IC card type)
11.1
11.1.1
11.1.2
Using authentication unit (IC card type) ..................................................................................... 11-2
Configuring this machine ................................................................................................................. 11-2
Registering a user ............................................................................................................................ 11-4
Registering a user using the control panel of this machine ............................................................. 11-4
Registering a user using Data Administrator ................................................................................... 11-6
Checking the version of the installed Data Administrator................................................................ 11-6
Setup................................................................................................................................................ 11-7
User registration............................................................................................................................. 11-11
11.1.3
Logging in to this machine............................................................................................................. 11-15
When IC card authentication is enabled ........................................................................................ 11-15
When IC card authentication + password authentication is enabled ............................................ 11-16
Specifications
12.1
Paper .............................................................................................................................................. 12-2
Paper types and paper capacities ................................................................................................... 12-2
12.2
Machine specifications................................................................................................................. 12-4
bizhub C652/C652DS/C552/C552DS/C452 .................................................................................... 12-4
bizhub C652/C652DS/C552/C552DS/C452
Contents-5
Automatic duplex unit ...................................................................................................................... 12-7
Reverse automatic document feeder (bizhub C652/C552/C452).................................................... 12-7
Reverse automatic document feeder (bizhub C652DS/C552DS) .................................................... 12-7
12.3
13
14
Options........................................................................................................................................... 12-8
Large capacity unit LU-301.............................................................................................................. 12-8
Large capacity unit LU-204.............................................................................................................. 12-8
Finisher FS-526................................................................................................................................ 12-9
Saddle stitcher SD-508.................................................................................................................. 12-10
Punch kit PK-516 ........................................................................................................................... 12-11
Job Separator JS-602.................................................................................................................... 12-12
Z-Folding Unit ZU-606 ................................................................................................................... 12-12
Post Inserter PI-505 ....................................................................................................................... 12-13
Finisher FS-527.............................................................................................................................. 12-13
Saddle stitcher SD-509.................................................................................................................. 12-14
Punch Kit PK-517 .......................................................................................................................... 12-15
Job Separator JS-504.................................................................................................................... 12-15
Job Separator JS-603.................................................................................................................... 12-16
Authentication unit (biometric type) AU-101.................................................................................. 12-16
Authentication unit (biometric type) AU-102.................................................................................. 12-17
Authentication unit (IC card type) AU-201 ..................................................................................... 12-17
Appendix
13.1
Colors............................................................................................................................................. 13-2
Hue, brightness, and saturation....................................................................................................... 13-2
Red, green, and blue........................................................................................................................ 13-4
13.2
Image quality ................................................................................................................................. 13-5
Contrast, copy density, and sharpness ........................................................................................... 13-5
Color balance (CMYK) ..................................................................................................................... 13-6
13.3
Glossary ......................................................................................................................................... 13-7
Index
14.1
14.2
Index by item ................................................................................................................................. 14-2
Index by button.............................................................................................................................. 14-6
bizhub C652/C652DS/C552/C552DS/C452
Contents-6
1
Introduction
1.1
Welcome
1
Introduction
1.1
Welcome
1
Thank you for purchasing this machine.
This User's Guide describes the functions, operating instructions, precautions for correct operation, and
simple troubleshooting guidelines of this machine. In order to obtain maximum performance from this
product and use it effectively, please read this User's Guide as necessary.
1.1.1
User's guides
Printed manual
Overview
Quick Guide [Copy/Print/Fax/Scan/Box Operations]
This manual describes operating procedures and the
functions that are most frequently used in order to enable you to begin using this machine immediately.
This manual also contains notes and precautions that
should be followed to ensure safe usage of this machine.
Please be sure to read this manual before using this
machine.
User's guide CD manuals
Overview
Copy Operations
This manual describes details on copy mode operations and the settings of this machine.
• Specifications of originals and copy paper
• Copy function
• Maintaining this machine
• Troubleshooting
Enlarge Display Operations
This manual describes details on operating procedures of enlarge display mode.
• Copy function
• Scanning function
• G3 fax function
• Network fax function
Print Operations
This manual describes details on printer functions.
• Printer function
• Configuring the printer driver
Box Operations
This manual describes details on the boxed functions
using the hard disk.
• Saving data in User Boxes
• Retrieving data from User Boxes
• Printing and transferring data from User Boxes
Network Scan/Fax/Network Fax Operations
This manual describes details on transmitting
scanned data.
• Scan to E-Mail, FTP TX, SMB TX, Save in User
Box, WebDAV and Web Service
• G3 fax
• IP Address Fax, Internet Fax
Fax Driver Operations
This manual describes details on the fax driver function that transmits faxes directly from a computer.
• PC-FAX
Network Administrator
This manual describes details on setting methods for
each function using the network connection.
• Network settings
• Settings using PageScope Web Connection
bizhub C652/C652DS/C552/C552DS/C452
1-2
1.1
1.1.2
Welcome
1
User's guide CD manuals
Overview
Advanced Function Operations
This manual describes details on functions that become available by registering the optional license kit
and by connecting to an application.
• Web browser function
• Image Panel
• PDF Processing Function
• Searchable PDF
• My panel and My address function
Trademarks/Copyrights
This manual describes details on trademarks and
copyrights.
• Trademarks and copyrights
User's Guide
This User's Guide is intended for a wide range of users ranging from those using this machine for the first
time to administrators.
It describes basic operations, functions that enable more convenient operations, maintenance procedures,
simple troubleshooting operations, and various setting methods of this machine.
Note that basic technical knowledge about the product is required to enable users to perform maintenance
work or troubleshooting operations. Limit your maintenance and troubleshooting operations to the areas
explained in this manual.
Should you experience any problems, please contact our service representative.
bizhub C652/C652DS/C552/C552DS/C452
1-3
1.2
Conventions used in this manual
1.2
Conventions used in this manual
1.2.1
Symbols used in this manual
1
Symbols are used in this manual to express various types of information.
The following describes each symbol related to correct and safe usage of this machine.
To use this machine safely
7 WARNING
-
This symbol indicates that a failure to heed the instructions may lead to death or serious injury.
7 CAUTION
-
This symbol indicates that negligence of the instructions may lead to mishandling that may cause injury
or property damage.
NOTICE
This symbol indicates a risk that may result in damage to this machine or originals.
Follow the instructions to avoid property damage.
Procedural instruction
0
This check mark indicates an option that is required in order to use conditions or functions that are
prerequisite for a procedure.
1
This format number "1" represents the first step.
2
This format number represents the order of serial steps.
% This symbol indicates a supplementary explanation of a
procedural instruction.
%
A procedural operation
is illustrated.
This symbol indicates transition of the control panel to access a desired menu item.
This symbol indicates a desired page.
d Reference
This symbol indicates a reference.
bizhub C652/C652DS/C552/C552DS/C452
1-4
1.2
Conventions used in this manual
1
View the reference as required.
Key symbols
[]
This symbol represents a key name on the control panel, touch panel or the computer screen, power switch,
etc.
1.2.2
Original and paper indications
Original and paper sizes
The following explains the indication for originals and paper described
in this manual.
When indicating the original or paper size, the Y side represents the
width and the X side the length.
Original and paper indications
w indicates the paper size with the length (X) being longer than the
width (Y).
v indicates the paper size with the length (X) being shorter than the
width (Y).
bizhub C652/C652DS/C552/C552DS/C452
1-5
2
Part names and their
functions
2.1
Options
2
2
Part names and their functions
2.1
Options
2.1.1
bizhub C652/C652DS/C552/C552DS
18
19
20
2
3
4
1
5
6
17
16
7
15
13
14
8
9
12
10
11
No.
Name
Description
1
Main unit
The original is scanned by the scanner section, and the
scanned image is printed by the printer section.
Referred to as the "machine", the "main unit", or the
"C652/C652DS/C552/C552DS" throughout the manual.
2
Authentication unit (biometric type)
AU-101
3
Authentication unit (biometric type)
AU-102
Performs user authentication by scanning vein patterns in the finger.
Working table WT-506 is required to install the authentication unit.
4
Authentication unit (IC card type)
AU-201
Performs user authentication by scanning information
recorded on the IC card.
Working table WT-506 is required to install the authentication unit.
5
Working table WT-506
Provides an area to temporarily place an original or
other materials. This is also used when the authentication unit is installed.
bizhub C652/C652DS/C552/C552DS/C452
2-2
2.1
Options
No.
2
Name
Description
6
Keyboard holder KH-101
Mount this kit to use a compact keyboard.
For details on compact keyboards, contact your service representative.
7
Output Tray OT-503
Collects printed pages.
8
Mount kit MK-715
Used for banner printing.
• This option may not be available depending on the
sales area.
9
Image controller IC-412 v1.1
Allows you to use this machine as a network-enabled
color printer.
10
Large capacity unit LU-301
Can be loaded with up to 3,000 sheets of 8-1/2 e 11size (A4 -size) paper.
Referred to as the LCT throughout the manual.
11
Large capacity unit LU-204
Can be loaded with up to 2,500 sheets of 12 e 18-size
(A3-size) paper.
To change the paper size, contact your service representative.
Referred to as the LCT throughout the manual.
12
Saddle Stitcher SD-509
Install this unit onto the Finisher to allow Fold/Bind.
This unit is hereinafter referred to as the Saddle Stitcher through the manual.
13
Finisher FS-527
Sorts, groups and staples printed paper before feeding
out.
14
Punch Kit PK-517
Install this unit onto the Finisher to allow punching
holes.
15
Job Separator JS-603
Install this unit onto the Finisher.
Collects printed pages.
16
Z Folding Unit ZU-606
Installed onto the finisher to allow Z folding or punching.
17
Saddle stitcher SD-508
Installed onto the finisher to allow Fold/Bind.
Referred to as the saddle stitcher throughout the manual.
18
Finisher FS-526
Sorts, groups and staples printed paper before feeding
out.
19
Punch kit PK-516
Installed onto the finisher to punch holes.
20
Post Inserter PI-505
Installed onto the finisher to enable insertion of a cover
sheet into copied sheets. This unit also allows you to
manually operate the finisher (only the lower tray is
available).
21
Job Separator JS-602
Install this unit onto the Finisher.
Collects printed pages.
No illustration is provided as the options are built into the main body.
22
Fax kit FK-502
Allows this machine to function as a fax machine. Alternatively, it allows more telephone lines to be connected.
23
Stamp unit SP-501
Applies a stamp to originals that have been scanned.
24
Spare TX Maker stamp 2
A replacement stamp for the stamp unit.
25
Mount kit MK-720
Attach this kit to install an optional fax kit.
26
Local interface kit EK-604
Install this kit when using the compact keyboard. This
kit contains a speaker.
For details on compact keyboards, contact your service representative.
27
Local Interface Kit EK-605
Install this kit when using the connection function with
a Bluetooth-compatible cellular phone or PDA. This kit
contains a speaker and a receiving device for Bluetooth communication.
For details on compact keyboards, contact your service representative.
bizhub C652/C652DS/C552/C552DS/C452
2-3
2.1
Options
No.
2
Name
Description
28
Video interface kit VI-505
Required for installing the image controller onto this
machine.
29
Security Kit SC-507
Allows you to use Copy Guard or Password Copy.
This kit is used to prevent unauthorized copying.
30
i-Option LK-101 v2
Enables a Web browser and the Image Panel function
to be used on the control panel.
31
i-Option LK-102
Enables PDF document encryption with a digital ID, attachment of a digital signature, and property settings
when distributing a PDF document using the scan or
User Box function.
32
i-Option LK-103 v2
Provides both i-Option LK-101 v2 and LK-102 functions.
• This option may not be available depending on the
sales area.
33
i-Option LK-105
Provides the searchable PDF function.
34
Upgrade kit UK-203
Required when using Web browser, image panel, PDF
processing, searchable PDF, My panel, or My address
function. If necessary, you can increase up to nine languages, which can be displayed in the control panel of
this machine.
bizhub C652/C652DS/C552/C552DS/C452
2-4
2.1
2.1.2
Options
2
bizhub C452
14
15
2
16
3
4
1
5
6
13
7
8
12
9
10
11
No.
Name
Description
1
Main unit
The original is scanned by the scanner section, and the
scanned image is printed by the printer section.
Referred to as the "machine", the "main unit", or the
"C452" throughout the manual.
2
Authentication unit (biometric type)
AU-101
3
Authentication unit (biometric type)
AU-102
Performs user authentication by scanning vein patterns
in the finger.
Working table WT-506 is required to install the authentication unit.
4
Authentication unit (IC card type)
AU-201
Performs user authentication by scanning information recorded on the IC card.
Working table WT-506 is required to install the authentication unit.
5
Working table WT-506
Provides an area to temporarily place an original or other
materials. This is also used when the authentication unit
is installed.
6
Keyboard holder KH-101
Mount this kit to use a compact keyboard.
For details on compact keyboards, contact your service
representative.
7
Output Tray OT-503
Collects printed pages.
8
Mount kit MK-715
Used for banner printing.
• This option may not be available depending on the
sales area.
9
Image controller IC-412 v1.1
Allows you to use this machine as a network-enabled
color printer.
10
Large capacity unit LU-301
Can be loaded with up to 3,000 sheets of 8-1/2 e 11-size
(A4 -size) paper.
Referred to as the LCT throughout the manual.
bizhub C652/C652DS/C552/C552DS/C452
2-5
2.1
Options
No.
2
Name
Description
11
Large capacity unit LU-204
Can be loaded with up to 2,500 sheets of 12 e 18-size
(A3-size) paper.
To change the paper size, contact your service representative.
Referred to as the LCT throughout the manual.
12
Saddle Stitcher SD-509
Install this unit onto the Finisher to allow Fold/Bind.
This unit is hereinafter referred to as the Saddle Stitcher
through the manual.
13
Finisher FS-527
Sorts, groups and staples printed paper before feeding
out.
14
Punch Kit PK-517
Install this unit onto the Finisher to allow punching holes.
15
Job Separator JS-603
Install this unit onto the Finisher.
Collects printed pages.
16
Job Separator JS-504
Install this unit onto the Output Tray of the main unit to
offset the printed papers. This unit is hereinafter referred
to as the Job Separator through the manual.
No illustration is provided as the options are built into the main body.
17
Fax kit FK-502
Allows this machine to function as a fax machine. Alternatively, it allows more telephone lines to be connected.
18
Stamp unit SP-501
Applies a stamp to originals that have been scanned.
19
Spare TX Maker stamp 2
A replacement stamp for the stamp unit.
20
Mount kit MK-720
Attach this kit to install an optional fax kit.
21
Local interface kit EK-604
Install this kit when using the compact keyboard. This kit
contains a speaker.
For details on compact keyboards, contact your service
representative.
22
Local Interface Kit EK-605
Install this kit when using the connection function with a
Bluetooth-compatible cellular phone or PDA. This kit
contains a speaker and a receiving device for Bluetooth
communication.
For details on compact keyboards, contact your service
representative.
23
Video interface kit VI-505
Required for installing the image controller onto this machine.
24
Security Kit SC-507
Allows you to use Copy Guard or Password Copy.
This kit is used to prevent unauthorized copying.
25
i-Option LK-101 v2
Enables a Web browser and the Image Panel function to
be used on the control panel.
26
i-Option LK-102
Enables PDF document encryption with a digital ID, attachment of a digital signature, and property settings
when distributing a PDF document using the scan or
User Box function.
27
i-Option LK-103 v2
Provides both i-Option LK-101 v2 and LK-102 functions.
• This option may not be available depending on the
sales area.
28
i-Option LK-105
Provides the searchable PDF function.
29
Upgrade kit UK-203
Required when using Web browser, image panel, PDF
processing, searchable PDF, My panel, or My address
function. If necessary, you can increase up to nine languages, which can be displayed in the control panel of
this machine.
30
Heater HT-508
Install this unit into the tray to dehumidify the paper. Dehumidifying prevents paper in the tray from absorbing
moisture.
• This option may not be available depending on the
sales area.
bizhub C652/C652DS/C552/C552DS/C452
2-6
2.2
Main Body
2
2.2
Main Body
2.2.1
Outside of the main body (front)
3
2
4
1
5
6
7
8
30
9
29
10
11
12
28
13
27
14
15
26
16
17
25
18
24
19
23
No.
22
21
20
Name
1
Control panel
2
Left-side cover release lever
3
Left-side cover
4
Lateral guide
5
ADF
6
Original tray
7
Original output tray
8
Sub power switch
9
USB port (type A) USB 2.0/1.1
10
USB port (type A) USB 2.0/1.1 (For compact keyboard)
11
Automatic duplex unit release lever
12
Automatic duplex unit
bizhub C652/C652DS/C552/C552DS/C452
2-7
2.2
Main Body
2
No.
Name
13
Upper right-side door
14
Upper right-side door release lever
15
Bypass tray door
16
Bypass Tray
17
Bypass tray door release lever
18
Lower right-side door
19
Lower right-side door release lever
20
Paper-empty indicator
21
Total counter
22
Main power switch
23
Tray 4
24
Tray 3
25
Tray 2
26
Tray 1
27
Lower front door
28
Upper front door
29
Output tray
30
Status indicator
bizhub C652/C652DS/C552/C552DS/C452
2-8
2.2
2.2.2
Main Body
2
Outside of the main body (rear)
The illustration above shows the main unit with an optional video interface kit, fax kit, and mount kit.
1
2
13
12
11
10
9
4
3
5
6
8 7
No.
Name
1
Finisher connector
2
Filter
3
Power cord
4
Power switch for dehumidifying heater
5
Jack for connecting a telephone (TEL PORT2)
6
Telephone jack 2 (LINE PORT2)
bizhub C652/C652DS/C552/C552DS/C452
2-9
2.2
Main Body
No.
2
Name
7
Jack for connecting a telephone (TEL PORT1)
8
Telephone jack 1 (LINE PORT1)
9
USB port (type A) USB 2.0/1.1
10
RS-232C port
11
USB port (type B) USB 2.0/1.1
12
Network connector (10Base-T/100Base-TX/1000Base-T)
13
Ozone filter
bizhub C652/C652DS/C552/C552DS/C452
2-10
2.2
2.2.3
Main Body
2
Main bodyInside
bizhub C652/C552/C452
8
12
13
1
7
6
11
10
2
9
3
5
4
No.
Name
1
Original glass
2
Fusing unit
3
Fusing unit cover lever
4
Print head glass cleaning tool
bizhub C652/C652DS/C552/C552DS/C452
2-11
2.2
Main Body
No.
2
Name
5
Waste toner box
6
Imaging unit
7
Charger-cleaning tool
8
Imaging unit release lever
9
Toner cartridges
10
Slit glass
11
Original scales
12
Jam removal dial
13
Slit glass cleaner
bizhub C652/C652DS/C552/C552DS/C452
2-12
2.2
Main Body
2
bizhub C652DS/C552DS
14
8
12
7
6
13
1
10
9
11
2
3
5
4
No.
Name
1
Original glass
2
Fusing unit
3
Fusing unit cover lever
4
Print head glass cleaning tool
bizhub C652/C652DS/C552/C552DS/C452
2-13
2.2
Main Body
No.
2.2.4
2
Name
5
Waste toner box
6
Imaging unit
7
Charger-cleaning tool
8
Imaging unit release lever
9
Toner cartridges
10
Slit glass (front)
11
Original scales
12
Opening and closing guide
13
Slit glass cleaner
14
Slit glass (back)
Control panel
1
2
3
4
5
8
7
No.
6
Name
1
Stylus pen
2
Touch panel
3
Main power indicator
4
Sub power switch
5
Function key
6
Data indicator
bizhub C652/C652DS/C552/C552DS/C452
2-14
2.2
Main Body
No.
2
Name
7
Keypad
8
Brightness adjustment dial
Adjusting the angle of the control panel
You can adjust the angle of the control panel of this machine among three levels. You can also tilt the control
panel to the left. Use the control panel at an angle convenient to use.
NOTICE
When tilting the control panel, do not grab the touch panel.
1
Pull the control panel release lever toward you, and then pull the
control panel up or down.
You can tilt the angle of the control panel to one of the three
positions.
2
To tilt the control panel to the left or right, hold the bottom of the
control panel, and then tilt the panel to the left or right.
bizhub C652/C652DS/C552/C552DS/C452
2-15
2.2
2.2.5
Main Body
2
Touch panel
When the machine has been turned on and is ready to begin the copy operation, the basic settings screen
appears. To activate a function or to select a setting, lightly press the desired button appearing in the screen.
The basic settings screen can be switched between the Basic tab and Quick Copy tab. The arrangement of
the buttons and screens differ with the Basic tab and Quick Copy tab; however, the functions that can be set
are the same. This manual describes procedures for configuring settings from the Basic tab. The Quick Copy
tab displays the setting items of the Basic tab on one screen, which is useful for configuring multiple settings.
NOTICE
Do not apply excessive pressure on the touch panel. Such impact may leave a flaw on the panel, inviting
damage to the touch panel. When operating in the touch panel, never press down on the touch panel with
force or with a pointed object such as a mechanical pencil.
Basic tab
1
7
6
2
5
3
4
Quick Copy tab
1
7
8
2
9
5
4
No.
3
Name
1
Message display area
2
Functions/settings display area
3
Icon/shortcut key display area
4
Toner supply indicators
5
Left panel
6
Check Job
7
Job List
8
Copier setting button (arrow)
bizhub C652/C652DS/C552/C552DS/C452
2-16
2.2
Main Body
No.
9
2
Name
Color settings
d Reference
To switch the basic settings screen:
Press the [Utility/Counter] key ö [User Settings] ö [Custom Display Settings] ö [Copier Settings] ö [Default
Tab].
To configure color selection settings for buttons and tabs:
Press the [Utility/Counter] key ö [User Settings] ö [Custom Display Settings] ö [Color Selection Settings] .
bizhub C652/C652DS/C552/C552DS/C452
2-17
2.3
Option
2
2.3
Option
2.3.1
Finisher FS-526/Saddle stitcher SD-508/Punch kit PK-516
2
3
4
5
6 7
8 9
1
10
11
12
20
13
14
19
18
15
17
16
26
21
22
23
25
No.
24
Name
1
Output tray 2
2
Output tray 1
3
Front door
bizhub C652/C652DS/C552/C552DS/C452
2-18
2.3
Option
No.
2
Name
4
Horizontal transport unit cover
5
Jam removal dial [FN8]
6
Guide lever [FN7]
7
Guide lever [FN9]
8
Jam removal dial [FN6]
9
Jam removal dial [FN5]
10
Guide lever [FN3]
11
Guide lever [FN4]
12
Punch kit
13
Punch scrap box
14
Guide lever [FN10]
15
Recessed pull
16
Jam removal dial [FN11]
17
Saddle stitcher
18
Output belt
19
Output tray switch*
20
Folding output tray
21
Jam removal dial [FN2]
22
Guide lever [FN1]
23
Staple replacement door
24
Guide lever [FN13]
25
Guide lever [FN14]
26
Exit cover
* Press the output tray switch to move folded and center stapled paper to the end of the folding output tray.
bizhub C652/C652DS/C552/C552DS/C452
2-19
2.3
2.3.2
Option
2
Job separator JS-602
1
No.
2
Name
1
Finishing tray
2
Job separator cover
bizhub C652/C652DS/C552/C552DS/C452
2-20
2.3
2.3.3
Option
2
Z Folding Unit ZU-606
5
6
8
7
9
11
10
1
2
4
No.
Name
1
Z folding/conveyance unit
2
Guide lever [FN1]
3
Punch scrap box
4
Front door
5
Guide lever [FN6]
6
Guide lever [FN7]
7
Guide lever [FN8]
8
Recessed pull [FN2]
9
Jam removal dial [FN5]
bizhub C652/C652DS/C552/C552DS/C452
3
2-21
2.3
2.3.4
Option
2
No.
Name
10
Guide lever [FN3]
11
Jam removal dial [FN4]
Post Inserter PI-505
6
4
5
1
3
2
No.
Name
1
Post inserter control panel
2
Lower tray paper guide
3
Lower Tray
4
Upper Tray
5
Upper Tray paper guide
6
Upper unit release lever
bizhub C652/C652DS/C552/C552DS/C452
2-22
2.3
2.3.5
Option
2
Finisher FS-527/ Saddle Stitcher SD-509/ Punch Kit PK-517/ Job Separator
JS-603
2
3
4
5
6
7
1
8
9
10
11
14
13
12
bizhub C652/C652DS/C552/C552DS/C452
2-23
2.3
Option
2
15 16
17
18
20
No,
Name
1
Output tray 2
2
Output tray 1
3
Front door
4
Horizontal transport unit cover
5
Stapler
6
Guide lever [FN3]
7
Jam removal dial [FN2]
8
Guide lever [FN1]
9
Guide lever [FN4]
10
Staple holder
11
Punch scrap box
12
Saddle stitcher
bizhub C652/C652DS/C552/C552DS/C452
19
2-24
2.3
2.3.6
Option
2
No,
Name
13
Jam removal dial [FN6]
14
Recessed pull [FN5]
15
Transport unit
16
Punch kit
17
Job separator
18
Staple cartridge
19
Recessed pull [FN7]
20
Folding output tray
Job Separator JS-504
5
4
3
2
1
No.
Name
1
Jam removal dial
2
Eject assist lever
3
Output tray 2
4
Tray extension
5
Output tray 1
bizhub C652/C652DS/C552/C552DS/C452
2-25
2.3
2.3.7
Option
2
Large capacity unit LU-301/LU-204
2
3
1
5
4
2
1
3
5
4
No.
Name
1
Jam removal cover
2
Upper door
3
Paper take-up roller
4
Paper-empty indicator
5
Release lever
bizhub C652/C652DS/C552/C552DS/C452
2-26
3
Using this machine
3.1
Turning on or off the machine
3
Using this machine
3.1
Turning on or off the machine
3
This machine has two power controls: the [main power switch] and [sub power switch].
The [main power switch] turns on or off all functions of the machine. Normally, keep the [main power switch]
on.
The [sub power switch] turns on and off machine operations, for example, for copying, printing or scanning.
Turning [sub power switch] off causes the machine to enter power-saving mode.
0
0
0
0
0
0
0
0
0
When the [sub power switch] is turned on, the indicator on the [Start] key lights up in orange, and a
screen appears to indicate that the machine is starting up. After a few seconds, the message "Warming
up. Ready to scan." appears in the touch panel, and the indicator on the [Start] key lights up in blue,
indicating that a job can now be queued.
A job can also be queued while the machine is warming up after the [sub power switch] is turned on.
After the machine has finished warming up, the scanned image will be printed.
The default settings are the settings that are selected immediately after the machine is turned on and
before any settings are configured from the control panel or touch panel, and those that are selected
when the [Reset] key is pressed to cancel all settings configured from the control panel or touch panel.
The default settings can be changed.
Do not turn off the [main power switch] while a queued job or stored data is waiting to be printed. The
jobs yet to be printed will be deleted.
Settings that have not been registered and jobs in the printing queue are cleared when the [main power
switch] and [sub power switch] are turned off.
To turn the [main power switch] on immediately after turning it off, wait for 10 or more seconds before
turning it on again. Not doing so may result in an operation failure.
Do not turn off the [main power switch] or [sub power switch] while images are being scanned,
transmitted, or received. Data being scanned or communicated will be deleted.
Do not turn off the [main power switch] or [sub power switch] during the copying or printing process. If
you turn it off, a paper jam may occur.
Do not connect or disconnect the USB cable of the compact keyboard while this machine is turned on.
Do not also connect another medium to the USB port for the compact keyboard.
1
To turn the power on, open the main power switch cover, and then
press n on the [main power switch].
2
Close the main power switch cover.
3
Press the [sub power switch].
Check that the touch panel is turned on.
bizhub C652/C652DS/C552/C552DS/C452
3-2
3.1
Turning on or off the machine
4
3
To turn the power off, press the [sub power switch], then the [main power switch].
d Reference
To change the default settings for Copy:
Press the [Utility/Counter] key ö [User Settings] ö [Copier Settings] ö [Default Copy Settings].
bizhub C652/C652DS/C552/C552DS/C452
3-3
3.2
3.2
Basic copy operations
3
Basic copy operations
The following procedures describe how to set the original and the basic copy operations.
3.2.1
Placing originals
Place the original in the ADF or on the original glass. Select the optimal position for setting the original
according to the type of the original to be copied.
Using the ADF, a multi-page original can be fed and scanned automatically, one page at a time from
the top. The ADF can also be used to automatically scan 2-sided originals.
When using the original glass, place the original directly on the original glass for scanning. This method
is suited for originals in the form of a book and the like that cannot be fed through the ADF.
Load the original, and configure settings for relevant functions as needed.
Loading the original into the ADF
The following types of originals should not be loaded into the ADF. If loaded, paper may be jammed or the
original may be damaged.
Wrinkled, folded, curled, or torn originals
Highly translucent or transparent originals , such as OHP transparencies or diazo photosensitive paper
Coated originals such as carbon-backed paper
Originals printed on paper thicker than 55-7/8 lb (210 g/m2)
Originals printed on paper thicker than 34-1/16 lb (128 g/m2) for 2-sided printing
Originals that are bound, for example, with staples or paper clips
Originals that are bound in a book or booklet form
Originals with pages bound together with glue
Originals with pages that have had cutouts removed or are cutouts
Label sheets
Offset printing masters
Originals with binder holes
Originals that have just been printed with this machine
1
Slide the lateral guides to fit the size of the original.
2
Load the original face up in the original tray and arrange according
to the scanning order. Load the original pages so that the top of
the original is toward the back side of the machine.
% Do not load more than 100 sheets or up to the point where the
top of the stack is higher than the , mark. Such an action may
cause an original paper jam or damage to the original. It may
also invite machine failure. However, an original that exceeds
100 pages can be scanned in separate batches.
% If the original is not loaded correctly, it may not be fed in
straight, causing it to jam or become damaged.
% If the document is loaded in any orientation other than with the
top of the document toward the back of the machine, be sure
to select the document orientation.
3
Slide the adjustable lateral guides against the edges of the original.
bizhub C652/C652DS/C552/C552DS/C452
3-4
3.2
Basic copy operations
3
Placing the original on the original glass
0
0
0
0
When placing the original on the original glass, be sure to lift open the ADF at least 15°. If the original
is placed on the original glass without the ADF being lifted at least 15°, the correct document size may
not be detected.
Do not place an original weighing more than 4-7/16 lb (2 kg) on the original glass. Furthermore, do not
use a strong force to press down on a book or any other form of original that must be spread on the
original glass. Otherwise, the machine may be damaged or a failure may occur.
For thick books or large objects, perform scanning without closing the ADF. When a document is being
scanned with the ADF open, do not look directly at the original glass surface where light may be emitted
through. Note, however, that the light coming through the original glass is not a laser beam, and will not
expose the user to the related hazards.
When Non-Image Area Erase is selected, you do not have to close the ADF to copy the original. Place
the original anywhere on the original glass. The area surrounding the original text will be excluded from
the copy. For details, refer to page 5-42.
1
Lift open the ADF.
2
Place the original face down on the original glass.
% Load the original by placing it so that its top side faces the
back side of the machine.
3
Align the original with the
original scales.
mark in the back-left corner of the
% For transparent or translucent originals, place a blank sheet of
paper of the same size as the original over the original.
% For bound originals spread over two facing pages, such as a
book or a magazine, position the top of the original toward the back of this machine and align the
original with the
mark in the back-left corner of the original scales.
% When Non-Image Area Erase is selected, the original can be placed anywhere on the original glass.
4
3.2.2
Close the ADF.
Basic copy operations
The following procedure describes the basic copy operations.
1
Arrange originals in the order you want them to be scanned and
load them face up in the ADF.
% The original should be placed face down on the original glass.
2
Using the keypad, enter a value for the number of copies you desire.
% If you have entered incorrect number of copies, press the [C] (clear) key on the keypad, and then reenter the correct number.
3
Press the [Start] key.
The original is scanned and copied.
% To interrupt the copy operation being performed, press the [Stop] key.
% A "Ready to accept another job" message that appears during the current printing job indicates that
the next original can be scanned.
bizhub C652/C652DS/C552/C552DS/C452
3-5
3.2
Basic copy operations
3
% If an original with copy guard patterns embedded is scanned, the copy operation is stopped and
the job is discarded.
% If an original with a password embedded by the password copy function is scanned, the copy
operation starts after you enter the password.
% If multiple originals with different passwords are scanned at the same time, you will need to enter a
password for each original.
3.2.3
Copy operations using multiple functions
This section describes copy operations using combination of functions.
1
Load the original.
2
Press [Original Setting].
% For details on original setting, refer to page 5-15.
3
Press [Basic] ö [Duplex/Combine].
% For details on the Duplex/Combine settings, refer to page 5-8.
bizhub C652/C652DS/C552/C552DS/C452
3-6
3.2
Basic copy operations
4
Press [Basic] and then configure settings for respective functions.
%
%
%
%
%
%
5
3
For details on color setting, refer to page 5-4.
For details on paper size setting, refer to page 5-5.
For details on magnification setting, refer to page 5-7.
For details on image quality of originals, refer to page 5-18.
For details on copy density setting, refer to page 5-18.
For details on the setting not to rotate images, refer to page 5-14.
Press [Application] and then configure settings for respective functions.
% For setting for the application functions, refer to page 5-20.
6
Press [Basic] ö [Finishing].
% For details on copy finishing and folding/binding, refer to page 5-10.
bizhub C652/C652DS/C552/C552DS/C452
3-7
3.2
Basic copy operations
7
3
Press [Check Job] ö [Check Details].
% For details on checking job settings, refer to page 5-64.
8
Using the keypad, enter a value for the number of copies you desire.
% If you have entered incorrect number of copies, press the [C] (clear) key on the keypad, and then reenter the correct number.
9
Press the [Start] key.
The original is scanned and copied.
% To interrupt the copy operation being performed, press the [Stop] key.
% A "Ready to accept another job" message that appears during the current printing job indicates that
the next original can be scanned.
Functions that cannot be combined
Some settings cannot be combined with each other. If they are combined improperly, the settings will be
given priorities in either of the two ways described below.
The setting configured last is given priority. (The setting specified first is canceled.)
The setting configured first is given priority. (A warning message appears.)
bizhub C652/C652DS/C552/C552DS/C452
3-8
4
Control Panel Keys
4
4
Control Panel Keys
This section describes the functions of the keys on the operation panel.
Control panel and functions
Press the keys on the operation panel to use the Copy, Fax/Scan, User Box or other functions.
1
2
3
4
22
21
20
19
5
6
7
18
17
8
9
16
15
14 13 12
No.
11 10
Name
Description
Page
1
Touch panel
Displays various screens and messages. You can
configure various settings by directly touching the
touch panel.
-
2
Power indicator
Lights up in blue when the machine is turned on with
the [main power switch].
-
3
[Sub power switch]
Turns on or off machine operations. When turned off,
the machine is in the power-saving mode.
-
4
[Power Save]
Enters Power Save mode. While the machine is in
Power Save mode, the indicator on the [Power Save]
key lights up in green and the touch panel goes off.
To exit from Power Save mode, press the [Power
Save] key again.
p. 4-11
5
[Mode Memory]
Allows you to register (store) the desired
copy/fax/scan settings as a program or to recall a
registered program.
p. 4-7
6
[Utility/Counter]
Switches to the Utility screen or the Meter Count
screen.
p. 4-6
7
[Reset]
Resets all settings (except programmed settings)
entered using the control panel or touch panel.
p. 4-4
bizhub C652/C652DS/C552/C552DS/C452
4-2
4
No.
Name
Description
Page
8
[Interrupt]
Switches to Interrupt mode. While the machine is in
Interrupt mode, the indicator on the [Interrupt] key
lights up in green and the message "Now in Interrupt
mode" appears in the touch panel. To cancel Interrupt mode, press the [Interrupt] key again.
p. 4-4
9
[Stop]
Temporarily stops the operation while copying,
scanning or printing.
p. 4-4
10
[Proof Copy]
Allows you to print a single proof copy to be checked
before printing a large number of copies. You can
also display a finishing image using the current settings in the touch panel.
p. 4-18
11
[Start]
Starts the copy, scan or fax operation.
p. 4-4
12
Data indicator
Flashes in blue while a print job is being received.
Lights up in blue when a print job is queued to be
printed or while it is being printed. Lights up in blue
when there is saved fax data or unprinted fax data.
-
13
[C] (Clear)
Clears a value (such as the number of copies, a
zoom ratio and size) entered using the keypad.
p. 4-17
14
Keypad
Allows you to enter the number of copies to be produced, the zoom ratio, and various other setting values.
-
15
[Guidance]
Switches to the Guidance screen. You can display
descriptions of the functions and operating procedures.
p. 4-15
16
[Enlarge Display]
Enters Enlarge Display mode. If you are using PageScope Authentication Manager for authentication,
the Enlarge Display screen will not be available.
p. 4-14
17
[Accessibility]
Switches to the screen for configuring settings for
user accessibility functions.
p. 4-12
18
[Access]
If user authentication or account track settings have
been applied, press the [Access] key after entering
the user name and password (for user authentication) or the account name and password (for account track) in order to use this machine.
p. 4-8
19
[Brightness] dial
Allows you to adjust the brightness of the touch panel.
-
20
[User Box]
Enters User Box mode. While the machine is in User
Box mode, the indicator on the [User Box] key lights
up in green.
For details on User Box functions, refer to the "User's Guide [Box Operations]".
p. 4-5
21
[Fax/Scan]
Enters Fax/Scan mode. While the machine is in
Fax/Scan mode, the indicator on the [Fax/Scan] key
lights up in green.
For details on the fax/scan function, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
p. 4-5
22
[Copy]
Enters Copy mode. (As a default, the machine is in
Copy mode. ) While the machine is copying, the indicator on the [Copy] key lights up in green.
p. 4-5
bizhub C652/C652DS/C552/C552DS/C452
4-3
4.1
4.1
About the [Start] key, the [Stop] key, and the [Interrupt] key
4
About the [Start] key, the [Stop] key, and the [Interrupt] key
The [Start] key
%
Start the copy, scan or fax operation.
Press this key again to restart a suspended job.
% When this machine is ready to begin the operation, the indicator on the [Start] key lights up in blue.
If the indicator on the [Start] key lights up in orange, the copy operation cannot begin. (Check that
no warning or message is displayed in the touch panel.)
The [Stop] key
%
Press the [Stop] key while copying to temporarily stop the scanning or printing operation.
% To resume a temporarily stopped job, press the [Start] key.
% To delete a temporarily stopped job, select a job in the suspended job list in the screen, and press
the [Delete] key.
The [Interrupt] key
Press this key to start a new copy job with different copy settings by suspending the current job in process.
This is convenient when you need to make copies urgently.
0
0
The [Interrupt] key cannot be operated while an original is being scanned.
Pressing the [Interrupt] key restores the default settings.
1
Load the original.
2
Press the [Interrupt] key.
The indicator on the Interrupt key lights up in green and printing of the current job is suspended.
3
Configure the copy settings.
4
Press the [Start] key.
5
After the interrupting job has finished printing, press the [Interrupt] key.
The Interrupt indicator goes off and the interrupting copy settings are canceled.
The copy settings return to those specified before the interrupting copying job.
The [Reset] key
Resets all settings (except programmed settings) entered using the control panel or touch panel.
%
Press the [Reset] key.
The basic settings screen appears.
bizhub C652/C652DS/C552/C552DS/C452
4-4
4.2
4.2
About the [Copy] key, the [Fax/Scan] key, and the [User Box] key
4
About the [Copy] key, the [Fax/Scan] key, and the [User Box] key
This machine operates in Copy, Fax/Scan and User Box modes, from which the user can select a desired
function. The indicator on the selected key lights up in green.
The [Copy] key
%
Enters Copy mode.
The basic settings screen appears.
The [Fax/Scan] key
%
Press this key to enter Fax/Scan mode.
For details on the fax/scan function, refer to the "User's Guide [Network Scan/Fax/Network Fax
Operations]".
The [User Box] key
%
Enters User Box mode.
For details on User Box functions, refer to the "User's Guide [Box Operations]".
bizhub C652/C652DS/C552/C552DS/C452
4-5
4.3
4.3
The [Utility/Counter] key
4
The [Utility/Counter] key
Press the [Utility/Counter] key to display the Utility screen. You can configure the machine settings and check
its use status in the Utility menu screen.
%
Press the [Utility/Counter] key.
Settings
One-Touch/User Box Registration
Allows you to register items related to the fax/scanner and User Boxes operations.
For details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]" and "User's Guide [Box Operations]".
User Settings
Provides setting items that can be operated by the user.
Administrator Settings
Provides setting items that can only be operated by the administrator of the
machine.
Check Consumable Life
Allows you to check the status (usage level) of consumables.
Banner Printing
Allows you to select whether to enable or disable printing on long sheets
of paper.
This menu item appears when the optional finisher is not installed.
For details on long paper print, refer to the "User's Guide [Print Operations]".
Device Information
Displays information about this machine.
Function Version: Allows you to check the function version of the currently
installed firmware. Check the function version of this machine and of the
printer driver. Ensure that they match before using this machine.
IPv4 Address: Allows you to check the currently specified IPv4 address.
IPv6 Address: Allows you to check the currently specified IPv6 address.
bizhub C652/C652DS/C552/C552DS/C452
4-6
4.4
4.4
The [Mode Memory] key
4
The [Mode Memory] key
Combine frequently used copy settings into programs and register them with this machine. These programs
can easily be recalled as programs.
0
0
Up to 30 programs can be registered.
To register a program, configure the copy settings to be registered before pressing the [Mode Memory]
key.
%
Press the [Mode Memory] key.
Settings
Recall Copy Program
Select the button for the copy program registered with the copy settings to
be recalled.
Register Program
•
•
From the copy program buttons displayed in the screen, press the button you want to register copy settings with, and then press [Register
Program].
Enter the registration name, and then press [OK].
Check Program settings
Press this button to check the copy settings registered with the selected
copy program button.
Edit Name
Press this button to rename the registration name of the selected copy program button.
After enabling Copy Program Lock, [Edit Name] will not be displayed.
Delete
Press this button to delete the selected program button.
After enabling Copy Program Lock, [Delete] will not be displayed.
d Reference
To prohibit modification and deletion of copy programs:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Copy Program Lock Settings].
To delete a copy program:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Delete Saved Copy Program].
bizhub C652/C652DS/C552/C552DS/C452
4-7
4.5
4.5
The [Access] key
4
The [Access] key
If the administrator has configured user authentication settings/account track settings, only the users who
have been registered or the users whose accounts have been registered can use this machine.
If the administrator has configured a usage schedule, a user can use the machine by entering a password for
non-business hours.
Controlling access to the machine by user/account (user
authentication/account track)
0
0
0
0
0
0
0
0
0
0
%
With the user authentication/account track functions enabled, only the users who enter passwords for
users or for accounts can use this machine.
Thus, the number of copies among others can be managed by user/account.
Contact the administrator for information on the user name, account name, password and server name.
The login page that appears may vary depending on the user authentication/account track settings.
The user authentication settings can be used together with the account track settings. If the User
Authentication/Account Track is set to [Do Not Synchronize], complete user authentication, and then
log in by using the Account Track screen.
If MFP authentication or external server authentication has been set, a total of 1,000 users and accounts
can be registered.
After copying is completed, press the [Access] key to log out from the machine.
To get permission to use the machine, you can use an authentication unit (biometrics type/IC card type)
for authentication.
The account, which sets the use of this machine to suspend in Account Track Settings, cannot log in
to this machine. The users, who belong to the suspended account, cannot also log in to this machine.
If authentication is performed with PageScope Authentication Manager, check with your server
administrator for information on the login procedure.
Press the [Access] key.
Screen for user authentication
Screen for account track
bizhub C652/C652DS/C552/C552DS/C452
4-8
4.5
The [Access] key
4
Settings
User Authentication
Account Track
Performs the user authentication procedure to use this machine.
Public User Access
Allows users who have no access to the user
name or password to use this machine.
This item is not displayed when [Public User Access] is set to [Restrict] in the General Settings of
Administrator Settings.
If enhanced security mode has been enabled,
[Public User Access] is not displayed.
User Name
Enter the user name.
User Name List
Select a user name from a displayed list.
• If enhanced security mode has been enabled,
[User Name List] is not displayed.
• The user, who has set the use of this machine
to suspend in User Authentication Settings, is
not displayed in the [User Name List].
Password
Enter the password.
Server Name
Indicates the name of the default server. Press
[Server Name] to display the names of the registered servers. Select the desired server.
Login
Displays the basic settings screen, enabling you
to use this machine.
Performs the account track procedure to use this machine.
Account Name
Enter the account name.
Password
Enter the password.
When the account track input method is set to
[Password Only] in Administrator Settings, the
login screen displays only [Password]. The user
can directly enter the password in the login
screen from the keypad. For an all-number password, the user can log in without displaying the
keyboard screen, simply by pressing [Login], or
the [Access] key.
• For a password containing alphabets, numbers and/or symbol characters, press [Password] and then enter the password.
• After entering numbers from the keypad,
press [Password] to enter alphabets and symbols in succession.
Login
Displays the basic settings screen, enabling you
to use this machine.
d Reference
To configure user authentication/account track:
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track].
bizhub C652/C652DS/C552/C552DS/C452
4-9
4.5
The [Access] key
4
Using the machine during non-scheduled hours
The machine can be set to automatically enter Sleep mode according to a usage schedule determined by the
administrator so the use of the machine can be limited. This is referred to as Weekly Timer. Follow the
procedure described below to use the machine while the Weekly Timer is being used.
0
From the [Password for Non-Business Hours] screen (displayed from Administrator Settings mode), the
machine can be set so that the screen for entering the password for non-business hours is not
displayed.
1
Press the [Power Save] key.
2
Enter the password for non-business hours.
3
Press [OK].
4
Using the keypad, enter the length of time to elapse before the machine enters Sleep mode again.
5
Press [OK].
The basic settings screen appears.
d Reference
To configure Weekly Timer:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Weekly Timer Settings].
bizhub C652/C652DS/C552/C552DS/C452
4-10
4.6
4.6
The [Power Save] key
4
The [Power Save] key
If no operation is performed for a specified length of time, the touch panel goes off and the machine
automatically enters a mode where it conserves energy. This is referred to as Low Power or Sleep mode.
The following describes the procedure for returning from Low Power or Sleep mode.
0
0
Although the machine conserves more energy in Sleep mode than in Low Power mode, the warm-up
process for returning to ready-for-copy state from Sleep mode is more time-consuming.
As the factory default, Low Power mode is set to restart after 15 minutes and Sleep mode after 30
minutes. In other words, the machine enters Low Power mode if no operation is performed for 15
minutes. Likewise, it enters Sleep mode after 30 minutes has elapsed.
The machine can receive jobs even while it is in Low Power mode.
%
Press the [Power Save] key.
0
The machine returns from Low Power mode when any other key on the control panel or the touch panel
surface is pressed.
d Reference
To enable Low Power mode:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Power Save Settings].
bizhub C652/C652DS/C552/C552DS/C452
4-11
4.7
4.7
The [Accessibility] key
4
The [Accessibility] key
This section describes the procedures for configuring settings for the control panel and adjusting the touch
panel.
0
0
%
To return to the basic settings screen from the Accessibility Setting screen, press the [Accessibility] key,
the [Reset] key or [Close].
In the Enlarge Display screen, [Default Enlarge Display Settings] appears, enabling you to configure
default settings for use in the Enlarge Display mode using the copy or fax/scan functions.
Press the [Accessibility] key.
Page 1/2
Page 2/2
Settings
Touch Panel Adjustment
bizhub C652/C652DS/C552/C552DS/C452
Adjust the position of touch panel buttons when they do not respond correctly because they may not be correctly aligned with the position of the
actual touch sensor.
• The touch sensors are not aligned in the touch panel if pressing [Touch
Panel Adjustment] does not activate any action. Press the [1] key on the
keypad.
• Press the four check point buttons ([+]) on the touch panel adjustment
screen while listening on a buzzer sound each time. When the checking
by pressing the check point buttons is completed successfully, the indicator on the [Start] key lights up in blue. Press the [Start] key.
• The check point buttons ([+]) can be pressed in any order.
• To perform adjustment again, press the [C] (Clear) key, and then press
the four check point buttons ([+]) again.
• To cancel the touch panel adjustment process, press the [Stop] or [Reset] key.
• If the touch panel cannot be adjusted, contact your service representative.
4-12
4.7
The [Accessibility] key
4
Settings
Key Repeat Start/Interval
Time
Specify the length of time until the value begins to change after a touch
panel button is held down, and also specify the length of time for the value
to change to the next number.
The settings specified for Key Repeat Start/Interval Time are only applied
in Enlarge Display mode.
System Auto Reset Confirmation
Specify whether to display a message when the system auto reset operation is performed in Enlarge Display mode, allowing the user to choose either to continue operating without exiting Enlarge Display mode or to exit
Enlarge Display mode and return to the basic settings screen.
Also specify the duration of time for displaying the confirmation screen.
Auto Reset Confirmation
Specify whether to display a message when the automatic panel reset operation is performed in Enlarge Display mode, allowing the user to choose
either to continue operating without resetting the current settings or to reset the settings.
Also specify the duration of time for displaying the confirmation screen.
Enlarge Display Mode
Confirmation
Specify whether to display a message when the [Enlarge Display] key is
pressed to change the display of the screen, requesting confirmation to
cancel the settings that cannot be specified in Enlarge Display mode.
Message Display Time
Specify the duration of time for displaying warning messages, which appear, for example, when an incorrect operation is performed.
Sound Setting
Configure the settings for sounding associated with key operations. The
following sound setting functions are available. To produce a sound, press
[Yes], and then select the volume from [Low], [Medium] and [High]. To not
produce a sound, press [No].
[Operation Confirmation Sound]
• [Input Confirmation Sound]: A sound produced when a key in the control panel or a button in the touch panel is pressed for an entry
• [Invalid Input Sound]: A sound produced for invalid button operation in
the control panel or the touch panel
• [Basic Sound]: A sound produced when the default value item is selected for an option subject to rotational switching
[Successful Completion Sound]
• [Completed Operation Sound]: A sound produced when the operation
has completed normally
• [Completed Transmission Sound]: A sound produced when a communications-related operation is completed normally
[Completed Preparation Sound]: A sound produced when a device is ready
[Caution Sound]
• [Simple Caution Sound (Level 1)]: A sound produced when the replacement time is nearing for supplies or a replaceable part and a message
appears in the touch panel
• [Simple Caution Sound (Level 2)]: A sound produced for a user error
• [Simple Caution Sound (Level 3)]: A sound produced when an error occurs that can be corrected by the user by referring to the message that
appears or the User's Guide
• [Severe Caution Sound]: A sound produced when an error occurs that
cannot be corrected by the user or requires action by a service representative
Default Enlarge Display
Settings
For details, refer to the "User's Guide [Enlarge Display Operations]".
bizhub C652/C652DS/C552/C552DS/C452
4-13
4.8
4.8
The [Enlarge Display] key
4
The [Enlarge Display] key
Press this key to enter Enlarge Display mode and enable machine operation using a screen with a layout with
larger-size characters.
For details on the Enlarge Display screen, refer to the "User's Guide [Enlarge Display Operations]".
0
0
Press the [Enlarge Display] key to return to normal display.
If PageScope Authentication Manager is used for authentication, the login screen cannot be switched
to the enlarged display mode.
%
Press the [Enlarge Display] key.
bizhub C652/C652DS/C552/C552DS/C452
4-14
4.9
4.9
The [Guidance] key
4
The [Guidance] key
Press this key to view and check descriptions of various functions and operating procedures. When the
[Guidance] key is pressed, the Guidance screen for the displayed screen appears.
0
0
0
0
0
0
%
From the Help main menu screen, you can find the target Guidance screen based on the function or
purpose.
Refer to the left panel of the Guidance screen to check the position of the displayed Guidance screen
in the menu structure.
Press [Close] in the Guidance screen to move up one level in the menu structure. Press [Exit] to exit
Guidance mode and return to the screen that was displayed before the [Guidance] key was pressed.
Press [To Menu] to display the Help main menu.
In the Main Menu and Guidance Menu screens, select items by pressing the button or by pressing the
key in the keypad.
The Guidance screens cannot be displayed when the following operations are being performed:
Scanning, printing a proof copy, preview of a finished copy, operating in Enlarge Display mode, or
operating in Accessibility mode
While the Guidance screen is displayed, the following keys on the operation panel are disabled:
[Start], [C], [Interrupt], [Proof Copy], [Access], [Mode Memory], and [Enlarge Display]
Press the [Guidance] key.
Settings
Function
Check descriptions by selecting a Guidance menu grouped by function
type and name.
Search by Operation
Check descriptions by selecting a Guidance menu grouped by operation
type.
• With [Go to function] displayed, the function for the selected operation
can be set. However, when the fax/scan function is used, for example,
[Go to function] displayed on a Guidance screen for the copy function,
for example, cannot be selected as it is a different function from the one
in use.
• Select [Copy] and press [Scan special original]; instructions and animation guidance are displayed to enable the user to view the procedure
for placing an original. However, Start Guidance is not displayed in the
animation guidance for placing an original.
Function Map
Check descriptions from a navigation destination of the current screen or
the menu structure it belongs to.
Other Functions
Check descriptions by selecting a Guidance menu grouped by useful function.
Name and Function of
Parts
Check the description of the main unit and its options.
Service/Admin. Information
Check the name, extension number and E-mail address of the administrator.
bizhub C652/C652DS/C552/C552DS/C452
4-15
4.9
The [Guidance] key
4
Settings
Consumables Replace/
Processing Procedure
bizhub C652/C652DS/C552/C552DS/C452
Check procedures for replacing the toner cartridge, imaging unit or waste
toner box, adding staples or discarding punch-hole scraps by viewing animations. Press the target button, and then press [Start Guidance].
4-16
4.10
4.10
The [C] (Clear) key
4
The [C] (Clear) key
Clears a value (such as the number of copies, a zoom ratio and size) entered using the keypad.
%
Press the [C] key.
The value is deleted. Enter the correct value.
bizhub C652/C652DS/C552/C552DS/C452
4-17
4.11
4.11
The [Proof Copy] key
4
The [Proof Copy] key
Printing one set to check the copy result (Proof Copy)
Print a single proof copy for checking before printing a large number of copies. This prevents copy errors
from occurring.
0
When printing a proof copy, specify multiple copies.
1
Load the original.
2
Select the desired copy settings.
3
Press the [Proof Copy] key.
4
Press [Print] and then select the original direction.
5
Press the [Start] key.
This prints one copy when the original has been loaded in the ADF.
6
When it has been loaded on the original glass, press the [Finish], then the [Start] key.
A single proof copy is printed.
7
Check the proof copy.
% If the proof copy is found all right, go to Step 10.
To change the copy settings, go to Step 8.
8
Press [Change Setting] in the proof copy screen.
After changing the copy settings in the Change Settings screen, press [OK]
% "Number of Sets" in the proof copy screen indicates "the number of sets printed in the proof copy
mode/the number of sets specified to be printed", and "Total # of Pages Printed" indicates "the
number of sheets printed in the proof copy mode/the total number of sheets to be printed".
% To stop copying while the screen for changing the settings is displayed, select the proof copy job
to be stopped from the list of jobs in the left panel, and then press [Delete].
% If no operation is performed for the specified length of time while this screen is displayed, the copy
job for which proof copy has been completed is registered as a stored job and the basic settings
screen appears again.
Stored job registration is performed when the System Auto Reset function is activated or one minute
after (if System Auto Reset is set to "OFF").
9
Press the [Proof Copy] key to repeat proof copy.
10
Press [Print].
The number of copies yet to be printed is registered as a copy job.
bizhub C652/C652DS/C552/C552DS/C452
4-18
4.11
The [Proof Copy] key
4
Using a preview image to check the copy result (Advanced Preview)
Check the finishing image of a copy in the touch panel before printing. This prevents copy errors from
occurring.
0
0
0
When you scan the original using the Program Jobs function, scan all originals, press [Finish], and then
preview the finishing state.
When you attempt to scan the original with an insert page specified, the machine scans the original first,
and then the insert original. When this process is complete, you can preview the finishing state.
To use the Book Copy or Booklet function, no preview is available. Check the finishing state after
printing.
The Punch settings are available only if the Punch Kit PK-516 or Z Folding Unit is installed on the
Finisher FS-526 or the Punch Kit PK-517 is installed on the Finisher FS-527.
Fold and Center Staple & Fold is available only if the Saddle Stitcher is installed on the optional Finisher.
The Z-fold settings are available only if the Z Folding Unit is installed on the optional Finisher FS-526.
1
Load the original.
2
Select the desired copy settings.
3
Press the [Proof Copy] key.
4
Press [Preview on Screen] for the proof copy method and then select the original direction.
5
Press the [Start] key.
0
0
0
The Preview (View Status) screen appears.
6
Check the preview image.
% To change the settings, press [View Pages]. Go to Step 7.
% To start printing, press the [Start] key.
% To scan another original, press [Finish], load the original, and then press the [Start] key.
7
Change the settings, and then press [View Status].
Settings
Prev. Page/
Next Page
Switch from the current screen to either the previous or the next screen.
Zoom
Enlarge the preview image and check the details. Press [+] and [-] to
change the zoom ratio from full size to 2, 4 or 8 times the normal size. To
select a different area to be enlarged, touch the scroll bar arrows on the
right and at the bottom side of the image.
The finishing state cannot be displayed if you change the display size.
bizhub C652/C652DS/C552/C552DS/C452
4-19
4.11
The [Proof Copy] key
4
Settings
Rotate Image
Rotate the preview image 180 degrees in order to correct the orientation of
the original if necessary.
Pressing
rotates the currently displayed page.
Pressing [Rotate Pages] displays the Scanned Page List. Select the page
to be rotated. Up to six scanned pages can be displayed. Press [ ] or [ ]
to change the selection.
View Finishing
View the finishing settings using icons or in text on the preview screen, and
check the finishing state.
Change Setting
Change the settings for the next original to be scanned.
View Pages/View Status
Switch between the View Status and View Pages tab in the Preview screen.
Perform image rotation and setting changes on [View Pages] and stop
scanning on [View Status].
8
Press the [Start] key.
Select this menu to start printing.
bizhub C652/C652DS/C552/C552DS/C452
4-20
5
Copy Function
5
5
Copy Function
You can configure the settings for multiple copy features by pressing buttons on the operation or touch panel.
This chapter describes the functions that can be configured by pressing the buttons in the touch panel.
Item
Basic
Configure the basic settings for making copies.
p. 5-3
Original Setting
Configure the type and size of the original.
p. 5-15
Quality/Density
Configure the quality or density for the original to optimize copy
quality.
p. 5-18
Application
Configure the application settings for making copies.
p. 5-20
Left panel
Job List
Check jobs currently being performed
and jobs waiting to be performed.
p. 5-62
Check Job
Check the current settings and the result
of the settings.
p. 5-64
bizhub C652/C652DS/C552/C552DS/C452
5-2
5.1
5.1
Basic
5
Basic
Configure the basic settings for making copies.
Item
Color
Specify the print color for making copies.
p. 5-4
Paper
Select the paper type to be printed on and paper tray.
p. 5-5
Zoom
Select the zoom ratio of the image to be copied.
p. 5-7
Duplex/Combine
Configure the 2-sided copy and combined copy settings.
p. 5-8
Finishing program
button
Configure frequently used offset and finishing settings in advance.
You can activate preferred finishing functions by simply pressing
this button.
p. 6-8
Finishing
Press this button to select the settings for offsetting and finishing
copies.
p. 5-10
Separate Scan
Select this item to divide a large original and scan it in a number of
batches.
p. 5-13
Auto Rotate OFF
Select this item to copy the original according to the paper orientation without rotating the image.
p. 5-14
Language Selection
Display the Language Selection screen to specify the language to
be displayed on the touch panel. This item is not displayed when
two shortcut keys are configured.
-
Shortcut Key
Allows you to arrange shortcut keys for the frequently used Application functions on the Basic screen.
-
bizhub C652/C652DS/C552/C552DS/C452
5-3
5.1
5.1.1
Basic
5
Color
Select the print color for making copies.
For the print color, you can select one from [Auto Color], [Full Color], [2 Color], [Black] and [Single Color].
%
Press [Basic] ö [Color].
Settings
Auto Color
Automatically detects whether the scanned original is in color or in black
and white, and selects the appropriate color setting (full color or black).
Full Color
Makes copies in full color, regardless of whether the scanned original is in
color or in black and white.
2 Color
Prints all areas of the scanned original determined to be in color with the
specified color, and prints all areas determined to be black in black.
Black
Prints the copy in black and white, regardless of whether the scanned original is in color or in black and white.
Single Color
Prints the copy in the specified single color, regardless of the color of the
scanned original.
When you specify a single color, the original is copied by converting the
color differences (apparent color densities) and the gradation levels into
density differences of the single color.
Average Density
bizhub C652/C652DS/C552/C552DS/C452
Copies the original by only converting the gradation levels into density differences of the single
color, regardless of the color differences in the
original,
5-4
5.1
5.1.2
Basic
5
Paper
Select the paper type and size to be printed, or to change the paper size and paper type settings specified
for each paper tray.
The paper size can be selected automatically according to the original size or it can be specified manually.
0
0
0
If you select [Transparency], specify [Black] for [Color] in advance.
The auto zoom setting and the auto paper setting cannot be selected at the same time.
If a setting for special paper is selected for a paper tray, that tray is not selected automatically with the
Auto Paper setting. (However, a paper tray set to Single Side Only is given priority to be selected with
1-sided printing.) When setting special paper in the paper tray, be sure to set the paper type. For details
on special paper, refer to page 12-2.
%
Press [Basic] ö [Paper].
Settings
Auto
Automatically selects the paper size according to the original size.
1-4
Trays
#
(Bypass Tray)
L
Large capacity unit
(Optional)
Change Tray Settings
bizhub C652/C652DS/C552/C552DS/C452
Allows you to specify the paper manually.
Specify the paper type and paper size for the selected paper tray.
Paper Type
Specify the paper type for the selected paper tray.
Paper Size
Specify the paper size for the selected paper tray.
[Auto Detect]:
Automatically detects the paper size.
[12-1/4 e 18 w] (Only for Tray 1 and Tray 2):
Enables 12-1/4 e 18 w to be selected.
[Standard Size] (only for Bypass Tray):
Specify a paper size to use the bypass tray as a
paper tray dedicated to the paper size.
[Custom Size] (only for Bypass Tray):
Enter the paper size.
[Wide Paper]:
Select a paper size larger than the original.
5-5
5.1
Basic
5
Configuring a custom size
%
[Basic] ö [Paper] ö [Bypass Tray] ö [Change Tray Settings] ö [Custom Size].
Settings
X/Y
•
•
Store
North American model (inch): Configure the length [X] and width [Y] with
pressing [+] or [-].
European model (cm): Enter the length [X] and width [Y] of the paper.
Register custom paper sizes.
memory 1 to 5
Select the memory button where the paper size is
to be stored.
Change Custom Size
Name
Rename memory button names.
Configuring wide paper
%
[Basic] ö [Paper] ö [Bypass Tray] ö [Change Tray Settings] ö [Wide Paper].
Settings
Wide Paper
Select the size of the paper to be loaded.
Change Size
X/Y
Enter the length [X] and width [Y] of the paper.
Preset Paper Sizes
Enables 12 e 18 w to be selected.
bizhub C652/C652DS/C552/C552DS/C452
5-6
5.1
5.1.3
Basic
5
Zoom
The original image size in the original can be enlarged or reduced.
0
0
The auto zoom setting and the auto paper setting cannot be selected at the same time.
If the auto zoom setting is selected and an enlargement is to be copied on paper larger than the original,
load the original with the same orientation as the paper.
%
Press [Basic] ö [Zoom].
Settings
Auto
Automatically selects the most appropriate zoom ratio based on the size of
the loaded original and the specified paper size.
Full Size
Copies the original image in the size identical to the original (100%).
Manual
•
•
Enter the zoom ratio (25.0% - 400.0%) of the copy.
Under "Set Individual Zoom", you can enter different zoom ratios for
the X and Y directions.
Set Zoom
Enter the desired zoom and select the button to
register the value with.
"User Preset Zoom" indicates the registered
zoom.
Minimal
Copies an original image slightly smaller than the original size or the specified size. The image in the original is centered on the paper without any
cutoff.
Select this setting when you want to copy the entire scope of the original
within the paper used.
-/+
Configure the zoom ratio (25.0% - 400.0%) of the copy without changing
the aspect ratio.
Fixed Zoom
Select a preset zoom when copying from a fixed size original onto a fixed
size paper.
User Preset Zoom
Select a registered copy zoom value. To change the registered zoom values, use [Set Zoom].
d Reference
To set image rotation:
Press the [Utility/Counter] key ö [User Settings] ö [Copier Settings] ö [Enlargement Rotation].
bizhub C652/C652DS/C552/C552DS/C452
5-7
5.1
5.1.4
Basic
5
Duplex/Combine
Configure whether to scan one side or both sides of the originals and whether to print on one side or both
sides of the paper. Multiple (2, 4 or 8) pages of original images can be reduced in size and printed on a single
page.
Using the Duplex/Combine function, you can save paper sheets for copying.
%
Press [Basic] ö [Duplex/Combine].
Settings
1-Sided > 1-Sided
2-Sided > 1-Sided
1-Sided > 2-Sided
2-Sided > 2-Sided
Binding Position
Configure the binding position of the original and copies to be output.
Without setting the Binding Position, the resulting copy may not be what
you intended.
When [1- Sided > 1- Sided] is selected, the binding position cannot be set.
Original Binding
Position
bizhub C652/C652DS/C552/C552DS/C452
Select the original binding position from [LeftBind], [Right-Bind], [Top] and [Auto].
• If the binding position for the original is set to
[Auto], the position of the binding margin is
automatically selected. A binding margin
along the long side of the paper is selected if
the original length is 11-11/16 inch (297 mm)
or less. If the original length is more than 1111/16 inch (297 mm), a binding margin along
the short side of the paper is selected.
• If [Auto] is selected for the original binding position, the binding margin is set at the top or
on the left.
5-8
5.1
Basic
5
Settings
Binding Position
Output Binding Position
Select the output binding position from [Left
Bind], [Right Bind], [Top] and [Auto].
• If the binding position for the copy is set to
[Auto], the binding position is automatically
determined according to the orientation of the
loaded original. If the original length is 1111/16 inch (297 mm) or less, a binding position along the long side of the paper is selected. If the original length is more than 11-11/16
inch (297 mm), a binding position along the
short side of the paper is selected.
• If Output Binding Position is set to [Auto], the
binding position is set at the top or on the left.
Original Direction
Select the orientation of the original loaded into the ADF or placed on the
original glass.
Without setting original direction, the resulting copy may not be what you
intended.
No
Disables combined copy.
2in1
Copies images on two original pages on one sheet of paper.
Portrait original pages
Landscape original pages
4in1/8in1
4in1
Copies images of four original pages on one
sheet of paper.
<Horizontal>
<Vertical>
8in1
Copies images of eight original pages on one
sheet of paper.
<Horizontal>
<Vertical>
Horizontal
Vertical
bizhub C652/C652DS/C552/C552DS/C452
Specify the combine order of the original (Numbering Direction setting).
5-9
5.1
5.1.5
Basic
5
Finishing
Various settings can be selected for sorting and finishing copies fed into the copy output tray.
0
0
0
0
0
0
%
The Staple settings are available only if the optional finisher is installed.
The Punch settings are available only if the Punch Kit PK-516 or Z Folding Unit is installed on the
Finisher FS-526 or the Punch Kit PK-517 is installed on the Finisher FS-527.
The Fold/Bind is available only if the Saddle Stitcher is installed on the optional Finisher.
The Z-fold settings are available only if the Z Folding Unit is installed on the optional Finisher FS-526.
"Staple" cannot be used together with "Offset".
The Half-Fold, Center Staple & Fold or Tri-Fold function cannot be used together with any of "Offset",
"Staple" or "Punch".
Press [Basic] ö [Finishing].
Settings
Sort
Prints the copied sets separately when a multi-page original is copied.
1
1
14
3
2
1
Group
Makes multiple copies of each page when you make multiple copies of a multipage original.
4
3
21
1
1
1
bizhub C652/C652DS/C552/C552DS/C452
5-10
5.1
Basic
5
Settings
Offset Yes/No
Specify whether to separate each set of copies from another set in the output
tray when copying multiple sets of multi-page originals.
When the Finisher or Job Separator JS-504 is not installed:
If the following conditions are met, printed copies are fed out and sorted in an
alternating crisscross pattern.
• 8-1/2 e 11, A4 or B5 paper is used
• Paper of the same size and type is loaded with the w orientation in one paper tray and with the v orientation in another tray
• Auto paper selection is specified for the paper size setting
When the Finisher or Job Separator JS-504 is installed:
The copies are fed out and stacked on top of each other with each set shifted
to separate it.
Fold/Bind
When the Saddle Stitcher SD-508 is installed on the Finisher FS-526:
Half Fold
Center Staple & Fold
Tri-Fold
Z-Fold
To configure the Z folding setting, install the Z Folding Unit ZU-606.
When the Saddle Stitcher SD-509 is installed on the Finisher FS-527:
Half Fold
Center Staple & Fold
Staple
Staples copies in corner or at two points before they are output.
Punch
Punches holes in copies before they are output.
1
bizhub C652/C652DS/C552/C552DS/C452
5-11
5.1
Basic
5
Settings
Position Setting
Configure desired staple or hole-punch positions.
Select Auto, and the machine automatically judges the staple or punch positions for the paper relative to the original direction loaded.
• A staple or hole-punch position is set along the long side of the paper if the
original length is 11-11/16 inch (297 mm) or less.
• Staple or hole-punch positions are set along the short side of the paper if
the original length is more than 11-11/16 inch (297 mm).
• Staple or punching positions are set on the upper or left-side end.
• Be sure to load the original so that its top side is placed in the back.
• If desired, press [Original Direction], and then select the original direction.
5.1.6
Post Inserter
When the Post Inserter PI-505 is installed on the Finisher FS-526, you can manually operate the Finisher
FS-526 using the post inserter control panel.
Reference
Only the lower tray can be used as the output tray. The upper tray is not available.
Keys on control panel
1
2
10
9
No.
Name
1
Corner staple lamp
2
Center staple & fold lamp
3
[Finishing] key
4
2-hole lamp
5
3-hole lamp
6
[Select punch] key
7
[Start/stop] key
8
4-hole lamp
9
Tri-fold lamp
10
2 position staple lamp
bizhub C652/C652DS/C552/C552DS/C452
3
4
5
6
7
8
5-12
5.1
Basic
5
Finishing using Post Inserter
1
Place paper in the lower tray of the Post Inserter, and align the lateral guide to the paper size.
ABC
ABC
ABC
Front
Cover
%
%
%
%
%
2
ABC
Front
Cover
Set the paper by placing it so that its top side faces the back of the machine.
To use the corner staple or 2-staple option, load the paper face up.
To perform Punch, load the paper face up.
To perform Bind, load the front side of the bound paper face down.
To perform Tri-Fold, load the outside of the tri-folded paper face down.
Press [Finishing] key and [Select punch] key, and select the desired finishing.
% To configure Finishing settings, press [Finishing] key to turn the LED on. To configure punch
settings, press [Select punch] key to turn the LED on.
% Punch settings are available together with the corner staple or 2-staple option.
3
Press the [Start/stop] key.
% If [Start/stop] key is pressed during operation, the operation will be stopped.
5.1.7
Separate Scan
When the original contains pages exceeding the capacity of the ADF, you can divide the original into several
batches to handle each lot as a single copy job. You can also use the copy function by switching between
the ADF and the original glass for scanning the originals.
0
0
Do not load original sheets beyond the upper limit for the ADF. It would cause jamming and/or spoiling
of the original or failure of the machine.
When making 2-sided or combined copies using the original glass, the machine can scan a number of
original pages without enabling Separate Scan.
1
Load the original.
2
In the Basic tab, press [Separate Scan].
bizhub C652/C652DS/C552/C552DS/C452
5-13
5.1
Basic
3
5
Press the [Start] key.
The original is scanned.
4
Load the next batch of the original, and then press the [Start] key.
% To change the scanning settings, press [Change Setting].
5
Repeat Step 4 until all pages of the original are scanned.
6
After all original pages have been scanned, press [Finish].
7
Press the [Start] key.
d Reference
To set the Separate Scan output method:
Press the [Utility/Counter] key ö [User Settings] ö [Copier Settings] ö [Separate Scan Output Method].
5.1.8
Auto Rotate OFF
Select this setting to copy the original according to the paper orientation without rotating the image.
0
For some paper sizes or zoom values, part of the image may be cut off.
%
Press [Basic] ö [Auto Rotate OFF].
bizhub C652/C652DS/C552/C552DS/C452
5-14
5.2
5.2
Original Setting
5
Original Setting
Configure the original status or original direction for outputting desired copies.
%
Press [Original Setting].
Settings
Mixed Original
Loads originals of different sizes into the ADF and scan them at a time.
Z-Folded Original
Correctly detects the original size when folded originals are loaded into the
ADF and copied.
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Binding Position
Custom Size
Enter the original size.
Photo Size
Select the photo size.
Specify the original binding position (page margin) to prevent the copy
from being printed upside-down when scanning a 2-sided original,
Auto
Automatically configures the binding position of
the original.
• A binding margin along the long side of the
paper is selected if the original length is 1111/16 inch (297 mm) or less.
• If the original length is more than 11-11/16
inch (297 mm), a binding margin along the
short side of the paper is selected.
Original Direction
Specify the original direction to load into the ADF or place on the original
glass when copying 2-sided originals or making 2-sided or combined copies.
Despeckle
Reduces the influence of a dirt of the slit glass upon a copy output when
loading an original in the ADF.
bizhub C652/C652DS/C552/C552DS/C452
5-15
5.2
Original Setting
5
Copying mixed originals
Loads originals of different sizes into the ADF and scan them at a time.
To copy onto paper of the same size as the original, select [Full Size] in the Zoom tab and select [Auto] on
the Paper tab. To copy all original pages on paper of the same size, select [Auto] in the Zoom tab and select
the desired paper size on the Paper tab.
0
When [1-Sided > 2-Sided] is selected together with Auto Paper, the back side becomes blank if its
paper size is different from that of the front side. For example, if a single-sided original is copied in the
order of 11 × 17 (A3) and 8-1/2 × 11 (A4), it results in copying of the front side (11 × 17 (A3)) / back side
(blank) and of the front side (8-1/2 × 11 (A4)) / back side (blank).
NOTICE
Load all of the original pages into the ADF so that the top of the pages is toward the back or the left side of
the machine.
1
Slide the adjustable lateral guides of the ADF to fit the size of the
largest original page.
2
Arrange originals in the order you want them to be scanned and
load them face up in the ADF.
3
In the basic settings screen, press [Original Setting].
4
Press [Mixed Original].
% To cancel the setting, press [Mixed Original] again to deselect
it.
The following chart shows the possible combinations of standard-sized paper that can be used for the Mixed
Original setting.
Maximum Original Width
Original Size
11 e 17
w (A3
w)
8-1/2 e
11 v
(A4 v)
8-1/2 e
14 w
(B4 w)
8-1/2 e
11 w
(A4 w)
5-1/2 e
8-1/2 v
(A5 v)
5-1/2 e
8-1/2
w (A5
w)
(B5 v)
(B5 w)
11 e 17 w (A3
w)
o
o
-
-
-
-
-
-
8-1/2 e 11 v
(A4 v)
o
o
-
-
-
-
-
-
8-1/2 e 14 w
(B4 w)
o
o
o
-
-
-
o
-
8-1/2 e 11 w
(A4 w)
o
o
o
o
o
-
o
-
5-1/2 e 8-1/2
v (A5 v)
-
-
o
o
o
-
o
-
5-1/2 e 8-1/2
w (A5 w)
-
-
-
-
-
o
-
o
(B5 v)
o
o
o
-
-
-
o
-
(B5 w)
-
-
o
o
o
-
o
o
o
Possible to combine
-
Not possible to combine
bizhub C652/C652DS/C552/C552DS/C452
5-16
5.2
Original Setting
5
Copying Z-folded originals
Correctly detects the original size when folded originals are loaded into the ADF and copied.
The length of the first page of the original is detected, and the subsequent pages are scanned as pages of
the same size.
NOTICE
Unfold folded originals before loading them into the ADF. If the original is copied without being unfolded, a
paper jam may occur.
1
Load the original into the ADF.
2
In the basic settings screen, press [Original Setting].
3
Press [Z-Folded Original].
% To cancel the setting, press [Z-Folded Original] again to
deselect it.
bizhub C652/C652DS/C552/C552DS/C452
5-17
5.3
5.3
Quality/Density
5
Quality/Density
Select the setting for the image type of the original to better adjust the copy quality/density.
%
Press [Quality/Density].
Settings
Original Type
Select the original type (text and image type) to obtain better copy quality.
Text
Copies originals containing only text. The edges of
copied text are reproduced with sharpness, providing an image that is easy to read.
Text/Photo
[Photo Paper]:
Select this setting to print photos from originals
containing both text and images onto photographic paper. A smooth copy image is produced.
[Printed Photo]:
Select this setting to copy printed originals containing both text and images, such as pamphlets or
catalogs.
Photo
[Photo Paper]:
Select this setting when the original photos are
printed on photographic paper. Halftone original
images (photographs, etc.) that cannot be reproduced with the usual settings will be reproduced in
as nearly an original state as possible. A smooth
copy image is produced.
[Printed Photo]:
Select this setting to copy printed originals, such
as pamphlets or catalogs. Halftone original images
(photographs, etc.) that cannot be reproduced with
the usual settings will be reproduced in as nearly
an original state as possible.
Map
bizhub C652/C652DS/C552/C552DS/C452
Select this setting to copy originals with a background color, originals containing pencil markings
or fine colored lines such as maps. A sharp copy
image is produced.
5-18
5.3
Quality/Density
5
Settings
Original Type
Dot Matrix Original
Select this setting to copy originals containing only
text that appears faint (such as that written with a
pencil). The copied text is reproduced so that it is
darker, making it easier to read.
Copied Paper
Select this setting to copy images (originals) printed using this machine.
Density
Adjust copy density.
Background Removal
Adjust the density of the background area for originals with colored background (newsprints, recycle paper, etc.) or originals on thin paper showing
text or images from the back.
Select [Auto] for "Background Removal Level" to enable automatic background density adjustment for copying with the optimal background density.
For "Background Removal", normally [Bleed Removal] is selected. However,
when copying an original with colored background, select [Paper Discoloration Adj] to make adjustment for background removal for copying.
Text Enhancement
Adjust the text reproduction level for an original with a photo overlapping the
text (background text) to clarify the text on the background.
To emphasize the text on the background, press [Daker Text] to adjust the
setting toward +.
To emphasize the background image, press [Lighter Text] to adjust the setting toward -.
[Text Enhancement] can be configured when an item other than [Photo] is
selected.
Glossy
Makes copies with a glossy finish.
bizhub C652/C652DS/C552/C552DS/C452
5-19
5.4
5.4
Application
5
Application
Configure the application settings for making copies.
Item
Sheet/Cover/Chapter
Insert
Inserts another sheet of paper or adds a cover page to the paper
for copying. You can also scan multiple copies of the original with
different settings.
p. 5-21
Edit Color
Inverts the contrast or gradation of the original or prints the original
in the mirror image. It also adds a color in the background or adjust
the quality of a color image.
p. 5-29
Book Copy/Repeat
Configure the settings for a book or catalog. An image on a single
sheet of original can be repeatedly copied or divided and enlarged
in parts to produce copies of the respective parts.
p. 5-33
Page Margin
Select the binding margin (blank area) of the paper used for copying.
p. 5-37
Image Adjust
Configure the layout for the image when the paper is larger than the
original.
p. 5-39
Booklet
Automatically arranges the page order of the scanned original and
makes 2-sided 2 in 1 copies to produce a page layout for a centerbound book, such as a magazine.
p. 5-40
Erase
Erases unnecessary outside portion of the original body text or
erases the area outside the original placed on the original glass.
p. 5-41
Stamp/Composition
Prints the date/time, page number or a stamp printed on copies.
This function also allows you to embed information for preventing
unauthorized copying in a document.
p. 5-43
Card Copy
Copies the contents of the front and back sides of a card-size original, for example, insurance card, driver's license, or business card,
on one sheet.
p. 5-59
Save in User Box
Saves the scanned original data in a User Box.
p. 5-60
bizhub C652/C652DS/C552/C552DS/C452
5-20
5.4
5.4.1
Application
5
Sheet/Cover/Chapter Insert
OHP Interleave
Prevent copies printed onto OHP transparencies from sticking together because of the heat produced during
copying by having paper (interleaves) inserted between the transparencies.
EFGH
EFGH
EFGH
EFGH
EFGH
EFGH
0
0
0
0
0
0
Printing on OHP transparencies is possible only in black.
Use interleaf paper with the same size as the OHP transparencies.
The number of copies is fixed to one. You cannot change.
The finishing function cannot be changed.
Load transparencies into the bypass tray.
Do not use a transparency that has been through the machine even once. It may lead to reduced print
quality, a paper jam or a damage to the machine. (Even if a transparency has been discharged without
printing, it cannot be reused.)
1
Load the original.
2
Press [Basic] ö [Color] ö [Black].
3
Load transparencies into the bypass tray. Load the interleave paper into the desired paper tray.
4
Set the paper type of the bypass tray to [Transparency] and press [OK].
5
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [OHP Interleave].
Settings
Interleave Paper
Select the paper tray loaded with paper with a transparency interleaf.
Transparency
Indicates the paper size of the loaded transparency.
d Reference
Setting Black for Color Settings:
Press [Basic] ö [Color] ö [Black].
bizhub C652/C652DS/C552/C552DS/C452
5-21
5.4
Application
5
Cover Sheet
Copies the front and back cover sheets onto separate paper when copying an original with a front/back cover
sheet. When the original to copy does not have a front and back cover, you can insert blank sheets of paper
as the front and back covers.
3
12 4
REPORT
34
12
REPORT 4
3
12
3
12 4
34
22
1
REPORT 4
3
22
1
0
Use paper of the same size for the body text and cover sheets, and ensure the same orientation of
paper for both purposes.
%
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Cover Sheet].
Settings
None
Disables copying of the front/back cover and blank sheet insertion.
Front (Copy)
For 1-sided copy:
Copies the first page of the original onto paper for the front cover sheet.
For 2-sided copy:
Copies the second page of the original onto the back of the paper for the
front cover sheet.
Front (Blank)
Adds paper for the front cover sheet as the first page of the copy.
Back (Copy)
For 1-sided copy:
Copies the last page of the original onto the back cover page.
For 2-sided copy:
Copies the last two pages of the original the 2-sided copy mode onto both
sides of the paper for the back cover when copying an original with an even
number of pages.
Back (Blank)
Add paper for the back cover sheet to the last page of the copy.
Paper
Select the paper tray loaded with the paper for the front/back cover page or
blank cover pages.
You can select the paper tray of the Post Inserter when [Front(Blank)] or
[Back(Blank)] is selected while the optional Post Inserter is installed.
d Reference
To configure the 2-sided copy mode:
Press [Basic] ö [Duplex/Combine].
bizhub C652/C652DS/C552/C552DS/C452
5-22
5.4
Application
5
Insert Sheet
A different sheet of paper (such as colored paper) can be inserted as specified pages in the copies. You can
select from two options: [Copy] and [Blank] to enable or disable copying to the inserted sheet.
0
0
You can specify up to 30 positions for insert sheets.
Use paper of the same size for the sheets to be inserted and for the original copies, and ensure the
same orientation of paper for both.
%
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Insert Sheet].
Settings
P ---
Specify where to insert sheets of a different paper type.
Sort
Sorts specified pages in the ascending order.
Insert Paper
Select the paper tray loaded with the paper to be inserted. You can select the
paper tray of the Post Inserter when [Blank] is selected while the optional Post
Inserter is installed.
Copy
Copies the original with the specified paper inserted for the specified pages.
When setting the specified page to "2"
For 1-sided copy:
Inserts the specified paper as the second page of the copies, and copies the
second page of the original onto it.
For 2-sided copy:
Leaves the back side of the first page of the copy blank, inserts the specified
paper for the second page of the copy, and makes a 2-sided copy of the second and third pages of the original onto the inserted sheet.
56
34
12
REPORT 4 5 6
3
12
56
34
12
REPORT 4 5 6
3
12
1
bizhub C652/C652DS/C552/C552DS/C452
2
3
1
2
4
4
6
5
REPORT
6
5-23
5.4
Application
5
Settings
Blank
Select this option to insert the specified paper sheet after the page you have
specified.
When setting the specified page to "3"
For 1-sided copy:
Inserts the specified paper as the fourth page of the copy.
For 2-sided copy:
Leaves the back side of the second page of the copy blank, and inserts the
specified paper for the third page of the copy.
3
12
REPORT
3
12
56
34
12
REPORT 4 5 6
3
12
6
45
6
45
4
1
4
5
REPORT
6
2
1
6
3
3
d Reference
To configure the 2-sided copy mode:
Press [Basic] ö [Duplex/Combine].
Insert Image
A multi-page original scanned on the original glass can be inserted at the pre-set location in an original first
scanned with the ADF.
34
12
REPORT 4
3
12
0
0
0
0
0
0
0
1
1
REPORT
AB
1
34
2
A
B
With the Insert Image function, the inserted original is added after the specified page.
You can specify up to 30 positions for the original to be inserted.
If the document scanned on the original glass has more pages than the number of pages specified in
the Insert Image screen, the remaining pages of the inserted original are printed at the end of the
original.
The original on the original glass is scanned with the same settings as for the original scanned in the
ADF.
If the original scanned on the original glass has fewer pages than the number of pages specified in the
Insert Image screen, the missing insertion pages will not be printed.
If the same page number is specified twice, two insertion original pages are added at the specified
location.
If the specified page number is greater than the total number of pages in the main original, the
corresponding insertion original page is added at the end of the copy.
Load the original into the ADF.
bizhub C652/C652DS/C552/C552DS/C452
5-24
5.4
Application
2
5
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Insert Image].
Settings
P ---
Specify the position to insert the page scanned through the original
glass.
Sort
Sorts specified pages in the ascending order.
3
Press the [Start] key.
4
Place the original to be inserted on the original glass.
5
Press the [Start] key.
% To insert a multi-page original, repeat steps 4 and 5 until all pages of the insertion original are
scanned in the order that they are to be inserted.
6
Press [Finish].
7
Press the [Start] key.
Copying begins.
bizhub C652/C652DS/C552/C552DS/C452
5-25
5.4
Application
5
Chapters
When making 2-sided copies, the pages specified as the first page of a chapter can be printed on the front
side of the paper. If the document was arranged so that the specified page would be printed on the back side
of a page, the page is left blank and the specified page is printed on the front side of the next page.
3
6
5
1
4
3
1
8
7
6
2
2
1
5
3
4
8
7
7
6
8
2
3
7
3
8
7
3
4
7
2
1
6
4
1
5
1
2
1
2
6
5
3
5
4
3
1
3
1
0
0
0
%
You can set up to 30 positions for the first page of chapters.
Enable the Chapters function to set [1-Sided > 2-Sided]. For a 2-sided original, select [2-Sided >2Sided].
Make sure that the paper loaded for the first page of the chapter and for text copies have the same size
and orientation.
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Chapters].
Settings
P ---
Specify the first page of the chapters.
Sort
Sorts specified pages in the ascending order.
Chapter Paper
Specify the paper tray for paper to be inserted for the first page of the chapter.
Copy Insert
Makes copies of the first pages of the chapters on paper of a different type
from that for the text pages.
None
Copies all pages with the same type of paper.
d Reference
To configure the 2-sided copy mode:
Press [Basic] ö [Duplex/Combine].
bizhub C652/C652DS/C552/C552DS/C452
5-26
5.4
Application
5
Program Jobs
When the originals to be copied include different types of materials such as a 1-sided original for full size
copying and a 2-sided original for enlarged copying among other things, you can use this setting for scanning
various originals with different settings and then copy them all in a single copying job.
Different Zoom or Paper settings can be specified for a part of the original or Finishing settings or a numbering
function can be set after the entire original is scanned, and then all copies can be printed together.
34
12
REPORT 4
3
12
34
12
REPORT
3
12
00
01
4
123
REPORT
4
123
0
0
Up to 100 types of originals can be scanned.
When configuring a program job, the [Group] setting cannot be selected in the Finishing screen.
Instead, select [Sort].
1
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Program Jobs].
2
Select the desired copy settings, and then press the [Start] key.
3
Press [Fix].
% Press [Retry] to delete the scanned job. Press [Change Setting] to configure the copy settings.
% When the original has been loaded on the original glass, press [Finish].
4
Load the next original and press [Change Setting].
bizhub C652/C652DS/C552/C552DS/C452
5-27
5.4
Application
5
5
Select the desired copy settings, and then press the [Start] key.
% Repeat Steps 3 to 5 until all originals have been scanned.
6
After all original pages have been scanned, press [Finish].
7
Press [Yes].
8
Specify finish settings as needed.
9
Press [Start] or the [Start] key.
bizhub C652/C652DS/C552/C552DS/C452
5-28
5.4
5.4.2
Application
5
Edit Color
Neg./Pos. Reverse
Use this function to enable the original to be copied with the density and gradations of the image inversed.
The images in the original are copied and output reversed like negative film of photographs.
0
0
If a single color is selected, the images are reversed relative to the selected color.
If a background color is selected, colors are reversed relative to the selected base color and the color
of the images.
%
Press [Application] ö [Edit Color] ö [Neg./Pos. Reverse].
% To cancel the Neg./Pos. Reverse function, press [Neg./Pos. Reverse] again.
d Reference
To set Single Color:
Press [Basic] ö [Color] ö [Single Color].
To Set Background Color:
Press [Application] ö [Edit Color] ö [Background Color].
bizhub C652/C652DS/C552/C552DS/C452
5-29
5.4
Application
5
Mirror Image
Copy originals as mirror images.
%
Press [Application] ö [Edit Color] ö [Mirror Image].
Settings
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
bizhub C652/C652DS/C552/C552DS/C452
5-30
5.4
Application
5
Background Color
Color the blank area of the original with a specified background color.
%
Press [Application] ö [Edit Color] ö [Background Color].
Settings
Select Color
Select a background color.
Color Adjustment
Adjust the image quality to fit an image based on the color-copied original.
1
Press [Application] ö [Edit Color] ö [Color Adjust].
bizhub C652/C652DS/C552/C552DS/C452
5-31
5.4
Application
5
Settings
2
Brightness
Adjust the brightness of the copied image.
Contrast
Adjust the copy density balance.
Saturation
Adjust how vivid colors should be for full color copies.
Red
Adjust how vivid red colors should be for full color copies.
Green
Adjust how vivid green colors should be for full color copies.
Blue
Adjust how vivid blue colors should be for full color copies.
Hue
Adjust the hue for full color copies.
The hue refers to a color trend relative to discrete colors such as red,
blue and yellow. By adjusting the hue, the image can attain more reddish or bluish tone, for example.
Copy Density
Adjust copy density (lighter or darker).
Sharpness
Adjust the sharpness to emphasize the edges of text so that copied
text can be read more easily. You can make an overly sharp original
image softer or a blurry image clearer.
Color Balance
Adjust the individual concentrations of yellow (Y), magenta (M), cyan
(C), and black (K) for full-color copies.
Full-color copy reproduces colors of the original by mixing toners of
four colors: yellow, magenta, cyan, and black.
By changing the amount of each of the four toners, adjust the tints in
the copy.
Configure respective functions.
% Press [Sample Copy] to see how it will appear with the currently specified color quality adjustment
settings.
bizhub C652/C652DS/C552/C552DS/C452
5-32
5.4
5.4.3
Application
5
Book Copy/Repeat
Book Copy
Divides or does not divide page spreads (such as a book or catalog) into left and right pages to copy data.
This function enables copying with the ADF open by placing the original on the Original Glass. If necessary,
you can place an original image at the center of the paper to copy.
SURVEYOR’S
REPORT
SURVEYOR’S
REPORT
0
0
0
0
0
0
%
Place the original on the original glass.
If [Book Copy] is selected, [Image Adjust] is set to [Centering] and [Erase] is set to [Non-Image Area
Erase] automatically. For details on [Centering], refer to page 5-39. For details on [Non-Image Area
Erase], refer to page 5-41. The automatically set [Centering] or [Non-Image Area Erase] can be
cancelled.
When [Book Spread] or [Separation] is selected, pressing the [Start] key starts printing.
When [Front and Back Cover] is selected, the scanning operation starts with the front cover followed
by scanning of the back cover, and ends with scanning of all two-page spreads of the body text in the
order of the page numbers.
When [Front Cover] is selected, all two-page spreads are scanned in order after the front cover.
When [Front and Back Cover] or [Front Cover] is selected, wait until all pages in the original are scanned
and then press [Finish] and then the [Start] key to start printing.
Press [Application] ö [Book Copy/Repeat] ö [Book Copy].
Settings
Book Spread
Copies both pages of a two-page spread original as a one page original.
Separation
Copies the right and left pages of two-page spreads separately in the order
of the page numbers.
Front Cover
Copies the front cover, the right and left pages of two-page spreads separately in the order of the page numbers, and the back cover in this order.
Front and Back Cover
Copies the front cover, separate copies of each page in the page spreads
and the back cover in the original page order.
bizhub C652/C652DS/C552/C552DS/C452
5-33
5.4
Application
5
Settings
Frame Erase
Erases projection of the dark shadow around the book.
Frame
Configure the width of the area around the entire
frame to be erased.
Top, Right, Bottom,
Left
Configure the width of the top, right side, bottom
and left side of the frame to be erased.
None
Select this settings to not erase the frame.
Center Erase
Erases projection of the dark shadow at the center of the book.
Binding Position
Select the binding position of the original.
To indicate it, select [Separation], [Front Cover], and [Front and Back Cover].
Image Repeat
An original image can be repeatedly printed on a single sheet of paper. Specify the original and paper sizes
or the zoom to automatically calculate the number of images to be copied accordingly. Alternatively, specify
the desired number of repetitions.
%
Press [Application] ö [Book Copy/Repeat] ö [Image Repeat].
Settings
With Margin
Repeats copying of the scanned area of the original so that the copy area of
the sheet is filled with the copied image. If the entire image does not fit into
the copy area, the extra range is not copied.
Without Margin
Repeats copying of the scanned area of the original so that the sheet is filled
with the copied image. However, some parts of the image may be lost.
Auto Detect
Automatically detects the area to be scanned.
bizhub C652/C652DS/C552/C552DS/C452
5-34
5.4
Application
5
Settings
Set Range
2/4/8 Repeat
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, or the reading range
must be specified, select the original size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
2 Repeat
4 Repeat
8 Repeat
Repeats copying of the scanned area of the original
as many times as specified. Note, however, that an
image that does not fit within the size of the paper
used is copied with partial cutoff.
[Repeat Interval Settings] can be configured only
for [2 Repeat].
Repeat Interval Settings
Specify the clearance between copied images.
Poster Mode
This function enables enlarged copy of the original image to a size exceeding the paper size that can be
loaded in the machine, such as the 34 e 44 (A0) or 24 e 36 (B0) size. Specify the original size and the output
size (enlarged copy size) to output enlarged copies of divided sections of the original onto separate sheets
of paper respectively. Create an enlarged copy of the specified finished size by joining those copies of
sections.
To create an 34 e 44-size (A0-size) poster, create copies of sections on eight 11 e 17-size (A3-size) sheets
and join them together.
0
0
Place the original on the original glass.
In Poster Mode, the number of copies is set to 1.
%
Press [Application] ö [Book Copy/Repeat] ö [Poster Mode].
Settings
Image Size
Select the finished image size.
Custom Size
bizhub C652/C652DS/C552/C552DS/C452
Enter the finished image size.
5-35
5.4
Application
5
Settings
Paper Size
•
•
North American model(inch):
Configure the width of the binding margin (1/16 inch to 3/4 inch) with
pressing [+] and [-]. When [None] is selected, the binding margin width is
set to 0 inch.
European model(cm):
Enter the width of the binding margin (0.1 mm - 20.0 mm). When [None]
is selected, the binding margin width is set to 0 mm.
Zoom
Enter the zoom to output a copy of the finished size.
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
Booklet Original
A catalog with its staples removed can be copied and bound with staples at the center to create copies of
the original catalog.
2
4
57
3
8
1
3
7
4
2
6
5
2
6
4
24
7
Staples
0
This function is available if a saddle stitcher is installed in the optional finisher.
NOTICE
Load a catalog with the staples removed.
1
Load the original.
% To use the original glass, position the pages in order, starting with the side that includes the first
page, then the side that includes the second page, then the side that includes the third page.
2
7
8
1
6
3
+
4
bizhub C652/C652DS/C552/C552DS/C452
5
5-36
5.4
Application
5
% To use the ADF, load the pages with the side that includes the first page on top.
3
6
1
5
7
6 3
2
5.4.4
4
8
8 1
2
Press [Application] ö [Book Copy/Repeat] ö [Booklet Original].
3
Press the [Start] key.
4
After all original pages have been scanned, press [Finish] and the [Start] key.
Page Margin
Copies can be printed with a binding margin so that the pages can easily be filed. When scanning a 2-sided
original, you can specify the paper binding position (binding margin for the paper) to prevent the copy from
being printed upside-down.
Left
4
22
ABC
1 ABC
ABC
DEF
DEF
ABC
GHI
DEF
GHI 4
DEF
GHI
GHI 22
1
1
4
23
ABC
ABC
DEF
ABC
DEF
ABC
GHI
DEF
GHI 4
DEF
GHI
GHI 23
1
3
1
ABC
2 DEF
GHI
AB
3
E
D
GH
Top
22
4
ABC
1 ABC
ABC
DEF
DEF
ABC
GHI
DEF
GHI 4
DEF
GHI
GHI 22
1
4
23
ABC
1 ABCDEF
ABC
DEF
ABC
GHI
DEF
GHI 4
DEF
GHI
GHI 23
1
3
ABC
DEF
GHI
3
2 ABC
ABC 1
DEF
DEF
Right
22
4
ABC
1 ABC
ABC
DEF
DEF
ABC
GHI
DEF
GHI 4
DEF
GHI
GHI 22
1
0
0
0
0
%
ABC
ABC 1
DEFABC
DEF
ABC
GHIDEF
GHI
DEF
4 4GHI
GHI
2
2
1
3
ABC
1
DEF 2
GHIB
3 EFC
HI
You can specify the binding position without creating a binding margin.
For 2-sided copy, you need to set the paper binding position and the original direction. Otherwise, the
original image may be copied up-side-down.
If the positions of the staples or punched holes are different from the binding position, the positions of
the staples or punched holes are given priority.
If part of the image is lost when copied with the specified binding margin settings, reduce the zoom and
perform copying.
Press [Application] ö [Page Margin].
bizhub C652/C652DS/C552/C552DS/C452
5-37
5.4
Application
5
Settings
Margin Position
Select an option from [Auto], [Left], [Top] and [Right].
When Auto is selected, the binding position is automatically set.
• This function automatically determines the binding position according to
the orientation of the loaded original. If the original length is 11-11/16
inch (297 mm) or less, a binding position along the long side of the paper
is selected. If the original length is more than 11-11/16 inch (297 mm), a
binding position along the short side of the paper is selected.
• The binding position is set on the upper or left-side end.
• Be sure to load the original so that its top side is placed in the back. If
the document is loaded in any other orientation, this setting fails.
Image Shift
Adjust the image position according to the binding margin.
Change Back Shift
Adjust Value
•
•
Original Direction
Adjust the image position on the back side of the
paper in the 2-sided copy mode.
North American model (inch): Configure the width of the binding margin
(1/16 inch to 3/4 inch) with pressing [+] and [-]. When [None] is selected,
the binding margin width is set to 0 inch.
European model (cm): Enter the width of the binding margin (0.1 mm 20.0 mm). When [None] is selected, the binding margin width is set to 0
mm.
Select the orientation of the original loaded into the ADF or placed on the
original glass.
d Reference
To set the zoom:
Press [Basic] ö [Zoom].
bizhub C652/C652DS/C552/C552DS/C452
5-38
5.4
5.4.5
Application
5
Image Adjust
If the paper is larger than the original, you can enlarge the original and copy it into the center of the paper.
Full Size
Center Zoom
Centering
%
Press [Application] ö [Image Adjust].
Settings
Full Size
Enlarges the image up to the largest possible paper size that can contain the
entire original, and copies the image at the center of the paper.
Place the original on the original glass.
Center Zoom
Enlarges the image up to the largest possible paper size that can contain the
entire original, and copies the image at the center of the paper. However,
some parts of the image may be lost.
Place the original on the original glass.
Centering
Copies the original image at the center of the paper without enlarging it.
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
bizhub C652/C652DS/C552/C552DS/C452
5-39
5.4
5.4.6
Application
5
Booklet
The page order of the scanned original is automatically arranged to produce 2-sided 2 in 1 copies in a page
layout for center binding, such as for a magazine.
Left binding
3
12
4
3
2
68 1
78
7
REPORT
3
5
12
6 3
78
REPORT
8
1
Right binding
3
12
0
0
0
%
5
61 8
6
7
78
2
REPORT
3
4
12
3 6
78
REPORT
1
8
Center Staple & Fold or Half-Fold is available if the Saddle Stitcher is installed in the optional Finisher.
Generally, a multiple of 4 pages is required with a 1-sided original, and a multiple of 2 pages is required
with a 2-sided original. If there are not enough pages, blank pages are automatically added at the end.
If a booklet is selected with the Auto Paper Select enabled, the zoom is automatically set at 64.7%
(70.7%).
Press [Application] ö [Booklet].
Settings
Left Bind/Right Bind
Select the output binding position for copies to be output.
Center Staple & Fold
Staples copies at two places along the center, then folds the copies in half
before feeding them out.
Half-Fold
Feeds out a copied sheet by folding it in two.
No
This setting feeds out a copied sheet without Center Staple & Fold or HalfFold.
Paper
Select the paper tray loaded with the desired paper.
Cover Sheet
Copies the front and back cover sheets onto separate paper when copying
an original with a front/back cover sheet. When the original to copy does not
have a front and back cover, you can insert blank sheets of paper as the
front and back covers.
bizhub C652/C652DS/C552/C552DS/C452
5-40
5.4
Application
5
d Reference
To set to an appropriate zoom:
Press the [Utility/Counter] key ö [User Settings] ö [Copier Settings] ö [Auto Zoom for Combine/Booklet].
5.4.7
Erase
Frame Erase
A
Copies can be produced by erasing shadows of punched holes, unnecessary areas around the original text,
such as the transmission information on received faxes and the shadows of punched holes. All four sides
around the original can be erased in the same width or in a different width for each side.
A
A:1/16 inch to 2 inch (0.1 mm to 50.0 mm)
%
Press [Application] ö [Erase] ö [Frame Erase].
Settings
Frame
Erases the four sides of the original in the same width.
Top Right Bottom Left
Erases each frame side in a different width.
+/-
•
•
None
North American model (inch): Press [+], [-] to set the erasing width between 1/16 inch and 2 inch.
European model (cm): Press [+], [-] to set the erasing width between 0.1
mm and 50.0 mm. The erasing width can also be entered using the keypad.
Sets the erasing width to 0 inch (0 mm).
bizhub C652/C652DS/C552/C552DS/C452
5-41
5.4
Application
5
Non-Image Area Erase
This function enables copying with the ADF open while having an original that cannot be loaded in the ADF
placed at a desired position on the original glass.
The original is automatically detected and the area outside the original text is erased.
Erase methods include "Bevel" and "Rectangular". "Bevel" is used when the background of the original is
thin and "Rectangular" is used when it is dark.
You can place the original on any position without opening or closing the ADF so that you can make copies
promptly. In addition, toner consumption will be reduced as the area outside the original text is erased.
Rectangular erasing
Bevel erasing
0
0
0
If erasing is not performed as desired, set "Erase Operation" under "Erase Adjustment" in Administrator
Settings.
The size of the original automatically detected is 3/8 inch e 3/8 inch (10 mm e 10 mm) or larger.
If the detection fails, a blank sheet of paper is output.
You cannot make copies with the ADF closed.
The original image may be defected at its top or end.
%
Press [Application] ö [Erase] ö [Non-Image Area Erase].
0
d Reference
To set Erase Operation:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Erase Adjustment].
bizhub C652/C652DS/C552/C552DS/C452
5-42
5.4
5.4.8
Application
5
Stamp/Composition
Add date and time, page number, stamp, image, or header or footer to make copies.
Item
Date/Time
Adds date and time to copies.
Page Number
Adds page numbers or chapter numbers to copies.
Stamp
Adds preset or registered stamps to copies.
Copy Security
Adds a hidden text for preventing unauthorized copying in a document when
copying. This function also allows you to copy a text with copy inhibit information or password embedded. Using this function, you can prevent original
information from being leaked.
Stamp Repeat
Repeats copying of a stamp or the date and time onto the paper.
Header/Footer
Adds date and time to the top or bottom of the paper to print copies.
Watermark
Adds a watermark (watery text) to the center of the copied pages.
Overlay
Makes copies with the image of the first scanned original page overlapping
the subsequent original images.
Registered Overlay
Saves an image of the scanned original as a registered overlay in the hard
disk and later overlay the registered image on the copy of another original.
bizhub C652/C652DS/C552/C552DS/C452
5-43
5.4
Application
5
Date/Time
You can select the print position and notation format to print the date and time. Specify whether to print on
all pages or only on the first page.
0
0
The date/time stamp cannot be printed on blank pages inserted using the Cover Sheet, Insert Sheet
and Chapters functions. Change the setting for printing on blank pages in Administrator Settings to
enable blank page printing.
The date/time as of scanning the original is stamped on the paper.
%
Press [Application] ö [Stamp/Composition] ö [Date/Time].
Settings
Date Format
Select the type (format) of date and time notation.
Time Format
Select the type (format) of date and time notation. When [None] is selected,
the time is not printed.
Pages
Select to print the date/time on all pages or only on the first page.
Print Position
Select a position from the nine print position options.
Adjust Position
Text Details
Adjust horizontal and vertical positions between
1/16 inch (0.1 mm) and 1-15/16 inch (50.0 mm).
Set the text color, size and type.
d Reference
To enable printing on blank pages:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Blank Page Print Settings].
bizhub C652/C652DS/C552/C552DS/C452
5-44
5.4
Application
5
Page Number
You can select the print position and notation format to print page numbers and chapter numbers. Page and
chapter numbers are printed on all pages.
0
Page numbers cannot be printed on blank pages inserted using the Cover Sheet, Insert Sheet and
Chapters functions. Change the setting for printing on blank pages in Administrator Settings to enable
blank page printing.
%
Press [Application] ö [Stamp/Composition] ö [Page Number].
Settings
Starting Page Number
•
Starting Chapter Number
•
•
•
Page Number Type
Set [Page Number] between -99999 and 99999, and set [Chapter] between -100 and 100.
Press [*] to switch over the signs (+ and -) of the setting.
If a negative value is specified, the numbers are not printed until the numbering reaches 1. For example, if "-1" was specified, the numbers are
printed starting with "1" on the third copied page.
The entered chapter number is printed if [1-1, 1-2...] is selected under
"Page Number Type".
Select the type (format) of the page.
bizhub C652/C652DS/C552/C552DS/C452
5-45
5.4
Application
5
Settings
Insert Sheet Setting
Print Position
Set this parameter when using the Cover Sheet, Insert Sheet and Chapters
functions together.
Cover Sheet
Print on Front and Back Cover:
Prints on the front and back covers.
Print on Back Cover Only:
Prints a page number on the back cover but not on
the front cover. Page number printing starts with
"2" for 1-sided copy and with "3" for 2-sided copy.
Do not print Page Number:
Disables printing on the front or back cover. Page
number printing starts with "2" for 1-sided copy
and with "3" for 2-sided copy.
Insert Sheet (Copy)
Print page #:
Prints on inserted pages.
Do Not Print #:
Counts but not prints on inserted pages.
Skip the Page(s):
Disables counting and printing on inserted pages.
Insert (Blank)
Do Not Print #:
Counts but not prints on inserted pages.
Skip the Page(s):
Disables counting and printing on inserted pages.
Select a position from the nine print position options.
Adjust Position
Text Details
Adjust horizontal and vertical positions between
1/16 inch (0.1 mm) and 1-15/16 inch (50.0 mm).
Set the text color, size and type.
d Reference
To configure the settings for the Cover Sheet, Insert Sheet and Chapters functions:
Press [Application] ö [Sheet/Cover/Chapter Insert].
To configure the settings for the Chapters function:
Press [Application] ö [Sheet/Cover/Chapter Insert] ö [Chapters].
To enable printing on blank pages:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Blank Page Print Settings].
bizhub C652/C652DS/C552/C552DS/C452
5-46
5.4
Application
5
Stamp
You can select the print position and notation format to print the stamp. Select printing on all pages or only
on the first page.
0
0
A stamp refers to text with printing contents fixed and preset. You can also select a stamp registered
with the Copy Protection Utility.
Stamps cannot be printed on blank pages inserted using the Cover Sheet, Insert Sheet and Chapters
functions. Change the setting for printing on blank pages in Administrator Settings to enable blank page
printing.
%
Press [Application] ö [Stamp/Composition] ö [Stamp].
Settings
Stamp Type/Preset
Stamps
Select a stamp to be printed from the eight types available.
Pages
Select to print the stamp on all pages or only on the first page.
Text Size
Select the character size used for the stamp.
Text Color
Select the text color for the stamp.
Print Position
Select a position from the nine print position options.
Adjust Position
Adjust horizontal and vertical positions between
1/16 inch (0.1 mm) and 1-15/16 inch (50.0 mm).
d Reference
To enable printing on blank pages:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Blank Page Print Settings].
bizhub C652/C652DS/C552/C552DS/C452
5-47
5.4
Application
5
Copy Protect
ABCD
0
0
ABCD
Dr
af
af raft
t
t
Dr Dra Dra
Dr
f
af
ft
af
t
t
D
Dr Dra Dra raft
ft
af
f
t
t
Dr
af
af raft
t
t
Dr Dra Dra
Dr
f
af
f
af
t
t
t
D
Dr Dra Dra raft
f
af
t
f
t
t
This function allows you to print a hidden text for preventing unauthorized copying, for example, a preset
stamp such as Private or date, in the background without particular distinction. If you copy a document with
Copy Protect printed, a text is highlighted on the entire sheet of paper to be printed, enabling you to know
that the copy is not authorized.
ABCD
0
0
The copy protection text is printed on all pages. The page to start with cannot be specified.
The selected copy protection text formats appear in the order they are placed, and can be used in
combination for up to eight text lines.
Use the PageScope Web Connection or Copy Protection Utility to register a registered stamp.
Multiple registered stamps or preset stamps cannot be selected.
%
Press [Application] ö [Stamp/Composition] ö [Copy Security]ö [Copy Protect].
Settings
Registered Stamp
Select one from registered stamps.
Preset Stamp
Select a stamp to be printed from the eight types available.
Date/Time
Select the type of date and time notation. When [None] is selected for Time
Format, the time is not printed.
The date/time as of scanning the original is stamped on the paper.
Other
Job Number
Select Yes to print the copy job number.
Serial Number
Select Yes to print the serial number of this machine.
For details on setting for the serial number, contact
your service representative.
Distribution Control
Number
Prints the distribution control number.
Specify the distribution control number using a value between 1 and 99999999.
Detail Settings
Configure the settings for Text/Background Color, Density, Copy Protect
Text, Text Size, Pattern Overwrite and Background Pattern.
bizhub C652/C652DS/C552/C552DS/C452
5-48
5.4
Application
5
Settings
Position
Change the angle. The angle can be changed when there are no more than
four lines in the selected copy protection text.
Change Pos./Delete
Change the arrangement order. Select the target
copy protection text and press [Up] or [Down].
To add a space to the copy protection text, press
[Insert Space]. Press either [Up] or [Down] to move
o that appears beside the specified copy protection text type, and then press [Insert].
To delete the copy protection text, press [Delete],
and then press the button for the copy protection
text to be deleted.
d Reference
To delete a registered stamp:
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Stamp Settings] ö
[Delete Registered Stamp].
Copy Guard
This function prints a document, embedding a Copy Guard pattern in a copy protect text, for example, a
preset stamp such as Private or date.
ABCD
0
0
0
Dr
af
af raft
t
t
Dr Dra Dra
Dr
f
af
f
af
t
t
t
D
Dr Dra Dra raft
f
af
t
f
t
t
If an attempt is made to copy copy-guarded sheets, the machine that supports this function scans a Copy
Guard pattern, stops copying, and discards the currently running job.
ABCD
NG
0
0
0
For a text, specify the pre-registered preset stamps.
The Copy Guard text is printed on all pages. The page to start with cannot be specified.
The selected Copy Guards appear in the order they are placed, and can be used in combination for up
to six text lines.
You can select the preset stamp, date/time, and the other items together.
Multiple preset stamps cannot be selected.
A Copy Guard cannot be printed on a colored paper, envelope, or transparency film.
%
[Application] ö [Stamp/Compositon] ö [Copy Security] ö [Copy Guard]
bizhub C652/C652DS/C552/C552DS/C452
5-49
5.4
Application
5
Settings
Copy Guard Type
Detail Settings
Preset Stamp
Select a stamp to be printed from the eight types
available.
Date/Time
Specify the type of the date or time to be printed on
paper. The date/time as of scanning the original is
stamped on the paper.
Other
Specify Job Number, Serial Number, and Distribution Control Number to be printed on paper. Serial
Number is assigned at the time of shipment of this
machine. For details on settings, contact your service representative.
Specify Text/Background Color, Copy Guard Pattern, Text Size, and Background Pattern to be printed on paper.
d Reference
To specify and detect a Copy Guard:
Select Utility/Counter ö [Administrator Settings] ö [Security Settings] ö [Security Details] ö [Copy Guard].
Password Copy
This function prints a document, embedding a copy protect text, for example, a preset stamp such as Private
or date, and a password for Password Copy.
If an attempt is made to copy password-copied sheets, the machine that supports this function scans a
Password Copy pattern and prompts you to enter the password. When the correct password is entered,
copying will start.
1234
0
0
0
0
0
0
0
0
0
12
ABCD
Dr
af raft
t
Dr
Dr
af
af
t
t
Dr Dra
af
f
t
t
ABCD
Dr
af raft
t
Dr
Dr
af
af
t
t
Dr Dra
af
ft
t
ABCD
af
t
Dr
Dr
af
af
t
Dr Dra
af
f
t
t
1234
af
t
Dr
Dr
af
af
t
Dr Dra
af
f
t
t
1234
NG
For a text, specify the pre-registered preset stamps.
A Password Copy is printed on all pages. The page to start with cannot be specified.
The selected Password Copy texts appear in the order they are placed, and can be used in combination
for up to six text lines.
You can select the preset stamp, date/time, and the other items together.
Multiple preset stamps cannot be selected.
A Password Copy cannot be printed on a colored paper, envelope, or transparency film.
If you fail to enter a password three times, the currently processed copy job will be erased.
If a password is detected on copies with Zoom, 2 Color, Grayscale, Color Adjust, Colored Paper,
Envelope, or Transparency specified, the currently processed copy job will be erased.
If multiple originals with different passwords are scanned, you will need to enter a password for each
original.
bizhub C652/C652DS/C552/C552DS/C452
5-50
5.4
Application
%
5
Select [Application] ö [Stamp/Composition] ö [Copy Security] ö [Password Copy].
Settings
Password
Enter the password to be embedded in paper.
Stamp Type
Preset Stamp
Select a stamp to be printed from the eight types
available.
Date/Time
Specify the type of the date or time to be printed on
paper. The date/time as of scanning the original is
stamped on the paper.
Other
Specify Job Number, Serial Number, and Distribution Control Number to be printed on paper. Serial
Number is assigned at the time of shipment of this
machine. For details on settings, contact your service representative.
Detail Settings
Specify Text/Background Color, Password Copy
Pattern, Text Size, and Background Pattern to be
printed on paper.
d Reference
To specify and detect a Password Copy:
Select [Utility/Counter] ö [Administrator Settings] ö [Security Settings] ö [Security Details] ö [Password
Copy].
Stamp Repeat
You can print a stamp, the date and time, or other specified items on all pages of the copy.
0
0
0
0
The printing contents of the Stamp Repeat function are printed on all pages.
The selected Stamp appear in the order they are placed, and can be used in combination for up to eight
text lines.
Use the PageScope Web Connection or Copy Protection Utility to register a registered stamp.
Multiple registered stamps or preset stamps cannot be selected.
bizhub C652/C652DS/C552/C552DS/C452
5-51
5.4
Application
%
5
Press [Application] ö [Stamp/Composition] ö [Stamp Repeat].
Settings
Registered Stamp
Select one from registered stamps.
Preset Stamp
Select a stamp to be printed from the eight types available.
Date/Time
Select the type of date and time notation. When [None] is selected for Time
Format, the time is not printed.
The date/time as of scanning the original is stamped on the paper.
Other
Job Number
Select Yes to print the copy job number.
Serial Number
Select Yes to print the serial number of this machine.
For details on setting for the serial number, contact
your service representative.
Distribution Control
Number
Prints the distribution control number.
Specify the distribution control number using a value between 1 and 99999999.
Detail Settings
Select the Text Color, Density, Text Size and Pattern Overwrite.
Position
Change the angle as required when there are no more than four lines in the
selected repeating stamp.
Change Pos./Delete
Change the arrangement order. Select the target
Stamp Repeat and press [Up] or [Down].
To add a space to repeated stamps, press [Insert
Space]. Press either [Up] or [Down] to move o that
appears beside the specified Stamp Repeat, and
then press [Insert].
To delete the Stamp Repeat text, press [Delete],
and then press the button for the Stamp Repeat
text to be deleted.
d Reference
To delete a registered stamp:
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Stamp Settings] ö
[Delete Registered Stamp].
bizhub C652/C652DS/C552/C552DS/C452
5-52
5.4
Application
5
Header/Footer
This setting enables printing the date/time and text at the top or the bottom of the paper. The date/time or a
distribution number can be printed on each page. The header and footer can contain predetermined
contents, but you can also temporarily change the contents.
0
In order to use the Header/Footer function, a header/footer must be registered in advance in
Administrator Settings. If no header/footer is registered in Administrator Settings, the [Header/Footer]
menu does not appear.
%
Press [Application] ö [Stamp/Composition] ö [Header/Footer].
Settings
Recall Header/Footer
Select a header/footer to be used.
Check/Change Temporarily
Check or temporarily change the contents of the registered header/footer.
Header Settings
Footer Settings
Reset
Select to enable or disable printing of a header/footer. To print a header/footer, configure the
following settings:
Text:
Enter the text for the header/footer.
Date/Time:
Select the type of date and time notation.
Other:
Select to print or not to print the distribution control
number, job number, or serial number.
Pages
Select to print the header/footer on all pages or
only on the first page.
Text Details
Select the Text Color, Text Size and Text Type.
Reset the settings to the initial contents.
d Reference
To register a header/footer:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Stamp Settings] ö
[Header/Footer Settings].
bizhub C652/C652DS/C552/C552DS/C452
5-53
5.4
Application
5
Watermark
You can print a watermark (light text) at the center of the paper. Select fixed preset text to be printed such
as "Invalid Copy" and "Private".
Copying with a watermark enables explicit indication of the use of the copied paper. It also helps prevent
unauthorized copy from the copied paper.
0
0
The watermark is printed on all pages at an angle of 45 degrees. It is printed once per page.
In case other settings affect the watermark printing to cause partial loss, the Watermark function is
canceled upon copying.
%
Press [Application] ö [Stamp/Composition] ö [Watermark].
Settings
Watermark Type
Select a watermark from the eight types available.
The watermark selected is printed over the original image.
Text Color
Select the watermark color from [Black], [Magenta] and [Cyan].
The watermark is printed in the selected color.
bizhub C652/C652DS/C552/C552DS/C452
5-54
5.4
Application
5
Overlay
Makes copies with the image of the first scanned original page overlapping the subsequent original images.
For example, if you set Overlay to copy three original pages, two pages are output, including "a merged
image of the first and second pages" and "a merged images of the first and the third pages".
The Overlay function is useful for overlay of text, pictures or figures not prepared in other Stamp/Composition
functions on the original.
%
Press [Application] ö [Stamp/Composition] ö [Overlay].
Settings
Pages
Select to print the overlay image on all pages or only on the first page. Selecting [1st Page Only] prints only on the second page of the original.
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
Density
Use the keypad to enter the density of an overlay image (using a value between 20 to 100%).
Color
Select the color of overlay image from [full color], [black], [red], [blue],
[green], [yellow], [cyan], or [magenta].
bizhub C652/C652DS/C552/C552DS/C452
5-55
5.4
Application
5
Settings
Composition
Transparent
Composes overlay image to be superimposed and
increases the brightness of the image. This setting
prevents an original from being hidden by the composed overlay image.
Background Composition (Original)
Composes the original as the background. The
overlay image is superimposed on the original
when they are printed.
Back
Composes the overlay image as the background.
The original is superimposed on the overlay image
when they are printed.
Registered Overlay
This function enables storing of an image from the scanned original as a registered overlay on the hard disk
for later use in copying another original. It is useful to register frequently used overlay images.
%
Press [Application] ö [Stamp/Composition] ö [Registered Overlay].
bizhub C652/C652DS/C552/C552DS/C452
5-56
5.4
Application
5
Settings
Recall Overlay Image
Register Overlay Image
Specify whether to print a registered overlay image on the front or back side.
Press an item to select an overlay image and configures its setting.
• You cannot select an overlay image when no overlay has been registered.
Thumbnail View
Display Name
In the screen view, you can check overlay images.
In the Display Name mode, you can check overlay
images using their file names. Select the desired
overlay image.
Detail Settings
Density:
Use the keypad to enter the density of an overlay
image (using a value between 20 to 100%).
Color:
Select the color of overlay image from [full color],
[black], [red], [blue], [green], [yellow], [cyan], or [magenta].
Composition:
Transparent
Composes overlay image to be superimposed and
increases the brightness of the image. This setting
prevents an original from being hidden by the composed overlay image.
Background Composition(Original)
Composes the original as the background. The
overlay image is superimposed on the original
when they are printed.
Back
Composes the overlay image as the background.
The original is superimposed on the overlay image
when they are printed.
Image Details
Check the "Name", "Registered Date", "Image
Size" and "Color" of the overlay image.
To confirm the enlarged overlay image, press [Preview].
New
Enter the name of the overlay image to be registered.
Load the overlay image original on the original
glass and press the [Start] key to have the overlay
image registered.
Overwrite
Select an overlay image to use for overwrite and
press [Overwrite].
Load the overlay image original on the original
glass and press the [Start] key to have the overlay
image overwritten.
Delete
Select an overlay image to be deleted and press
[Delete].
Detail Settings
Density:
Specify the density of an overlay to be registered
between 20% and 100%.
Color:
Select the color for the overlay image to be registered from [Auto Color], [Full Color] and [Black].
Pages
Select to print the overlay image on all pages or only on the first page.
Original Size
Select [Auto] to detect the size of the original automatically.
If the size of the original is not automatically detected, select the original
size.
Custom Size
Enter the original size.
Photo Size
Select the photo size.
bizhub C652/C652DS/C552/C552DS/C452
5-57
5.4
Application
5
d Reference
To prohibit changing the overlay registration:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Restrict Access to Job Settings] ö [Change Registered Overly].
bizhub C652/C652DS/C552/C552DS/C452
5-58
5.4
5.4.9
Application
5
Card Copy
Separately scans the contents of the front and back sides of a card, for example, insurance card, driver's
license, or business card, and copies them together on one sheet. You can copy a card with the full size or
enlarge an image to fit paper. Using the card copy function, you can save the number of sheets to be used.
A
B
A
B
0
0
0
A card must be placed in the erect mode on the original glass.
The card copy function and the auto paper function cannot be selected at the same time.
For some zoom values, part of the image may be cut off.
%
Select [Application] ö [Card Copy].
Settings
Original Size
Press [X] and [Y], and enter the size of the card to be copied. Also select the
pre-specified size from [size1] to [size4].
Layout
Specify where to place the front and back sides of a card.
Zoom
You can copy a card with the full size or enlarge an image to fit paper.
d Reference
To specify the default of Card Copy:
Select [Utility/Counter] ö [Administrator Settings] ö [Copier Settings] ö [Card Copy].
bizhub C652/C652DS/C552/C552DS/C452
5-59
5.4
5.4.10
Application
5
Save in User Box
This function enables saving of data from the scanned originals on the hard disk (in the User Box) built in the
machine. Documents saved in User Boxes can be printed when necessary.
For details on using documents saved in User Boxes, refer to the "User's Guide [Box Operations]".
%
Press [Application] ö [Save in User Box].
Settings
User Box
Select the destination User Box.
Document Name
Specify a document name for the read original.
A name automatically assigned to the document appears. You can change
the file name.
Save & Print
[Yes]:
Select to copy the scanned original and save it in the specified User Box.
[No]:
Select to save the data of the scanned original in the specified User Box.
bizhub C652/C652DS/C552/C552DS/C452
5-60
5.5
5.5
Left panel display
5
Left panel display
In the left panel of the basic settings screen, you can view the job list and the job status information.
You can also view the result of the settings being configured.
Job List
Check Job
Settings
Job List
Check Job
Lists jobs currently being performed or waiting to be performed.
If the Left Panel Display Default is set to "Status Display" in User Settings,
the job status is displayed.
Delete
To delete a job, select the job from the job list, and
then press [Delete].
Job Details
Opens the Job List screen.
Displays the result of the settings being configured.
Check Details
Check or change the current copy settings.
d Reference
To configure settings displayed as the default in the left panel:
Press the [Utility/Counter] key ö [User Settings] ö [Custom Display Settings] ö [Left Panel Display Default].
To prohibit other users from deleting jobs or to give permission to do so:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Restrict Access to Job Settings] ö [Delete Other User Jobs].
To prohibit or permit change if the print priority of jobs:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Restrict Access to Job Settings] ö [Changing Job Priority].
To hide the file name and destination in the job log:
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Security Details] ö [Hide
Personal Information].
To delete all job logs:
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Security Details] ö
[Initialize] ö [Job History].
bizhub C652/C652DS/C552/C552DS/C452
5-61
5.5
5.5.1
Left panel display
5
Job List
From the Job List screen, lists of jobs being performed by this machine and the jobs that have been
performed in addition to the job details can be viewed, and the job settings can be changed.
0
0
0
0
%
If user authentication settings have been applied and the machine is set so that jobs cannot be deleted
by other users, the job is not deleted.
If an Administrator Settings parameter was set so that the output priority of jobs cannot be changed,
[Increase Priority] does not appear and the output priority of the jobs cannot be specified.
When there is a job being printed, another job can be registered. Up to 251 jobs can be registered in
total.
If the authentication method is changed in Administrator Settings and all management data is cleared,
the jobs in the [Job History] are deleted.
Press [Job List] ö [Job Details] ö [Print].
Settings
Print
Opens the screen for checking print jobs.
Send
Opens the screen for checking fax and scan transmission jobs. For details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Receive
Opens the screen for checking fax reception jobs. For details, refer to
the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Save
Opens the screen for saving jobs. For details, refer to the "User's
Guide [Box Operations]".
bizhub C652/C652DS/C552/C552DS/C452
5-62
5.5
Left panel display
5
Settings
Current Jobs
Lists the jobs currently processed. Check the current status.
Delete
Deletes a job.
Increase Priority
(Displayed for the list
of print jobs in process)
The currently processed print job is interrupted and printing of the job given priority begins. Printing of the interrupted job is
automatically restarted once printing for the
job given priority is finished.
If the currently processed print job cannot be
interrupted because it contains Fold or Staple, the job given priority is executed after the
currently processed print job has been completed.
Release Held Job
(Displayed for the list
of print jobs in process)
Select to switch to the held job list and
change the settings of, print, or delete a held
job.
The held job list contains jobs that could not
be printed because, for example, system
auto reset was activated during the proof
copy.
• If desired, press [Change Settings] to
change the copy settings.
• For confirmation, press the [Proof Copy]
key to print a copy from a stored job.
Check Job Set.
Check job settings for stored jobs, jobs being
printed, jobs queued to be printed, and held
jobs.
Current Jobs
Detail
Check the status, results, error details, user
name, queued time, completed time, number
of original pages and number of copies for
jobs in process.
To delete the job, press [Delete] in the Detail
screen.
Job History
Lists completed jobs.
• This list includes jobs that failed because of an error.
• You can check the job logs and results.
• [Scanned Image] in the left panel displays the first page of the selected job with a thumbnail. To display thumbnails in [Scanned Image], set [Job History Thumbnail Display] in Administrator Settings
to [ON]. For details, refer to page 7-51.
bizhub C652/C652DS/C552/C552DS/C452
Deleted Jobs
Displays only jobs that were deleted before
they were finished.
Finished Jobs
Displays only jobs that were completed normally.
All Jobs
Displays all jobs.
Detail
Check the status, results, error details, user
name, queued time, completed time, number
of original pages and number of copies for
jobs in the Job History list.
5-63
5.5
5.5.2
Left panel display
5
Check Job
From the Check Job Settings screens, the current copy settings can be checked and changed if desired.
1
Press [Check Job] ö [Check Details].
2
Check the copy settings. To change the copy settings, press the relevant button.
3
After checking the settings, press [Close].
bizhub C652/C652DS/C552/C552DS/C452
5-64
6
User Settings
6
6
User Settings
User Settings are for setting items that a user can adjust as appropriate.
The contents of these setting items depend upon how the Administrator settings are configured. User
Settings cannot be initialized all at once. To initialize all settings, either manually reset them one by one or
contact your service representative.
Settings
System Settings
Configure the basic functions of this machine.
Custom Display Settings
Change the touch panel display to the convenience of the user.
Copier Settings
Configure the settings for copy functions to be used in copy operations.
Scan/Fax Settings
Configure setting for fax and scan operations.
Printer Settings
Configure setting is for the printer operations.
Change Password
Change the password for the user who is currently logged in.
Change E-Mail Address
Change the E-mail addresses specified for registered users.
Change Icon
Change the icons specified for registered users.
Register Authentication Information
Register or delete the biometric authentication information or IC card authentication information of the current login user.
Cellular Phone/PDA Setting
Configure settings to print data from a cellular phone or PDA.
bizhub C652/C652DS/C552/C552DS/C452
6-2
6.1
6.1
System Settings
6
System Settings
Configure the basic functions of this machine.
%
Press the [Utility/Counter] key ö [User Settings] ö [System Settings].
Settings
Language Selection
Select the language for display in the touch panel.
Measurement Unit Settings
Select the units for the values displayed in the touch panel.
Paper Tray Settings
Auto Tray Selection
Settings
Select the trays to be selected automatically
when the Auto Paper Select function is enabled.
Also configure the priority for the auto tray switch
operation to switch paper trays when it is enabled.
• Configure "Auto Paper Selection Setting" to
use paper types other than plain paper as
plain paper in a regular auto paper selection
mode.
Auto Tray Switch
ON/OFF
Select whether a paper tray loaded with paper of
the same size is selected automatically when a
paper tray that was selected manually becomes
empty while printing copies.
No Matching Paper in
Tray Setting
Specify the action to be taken when the matching
paper is not loaded into the specified paper tray.
• [Stop Printing (Tray Fixed)]
Printing stops.
• [Switch Trays (Tray Priority)]
Whether the matching paper is loaded into the
specified paper tray is determined first. And if
not, another tray that has the matching paper
loaded (if any) is selected.
Print Lists
Select the paper tray used for printing lists, such
as the sales counter and consumables indicators.
Also select whether to print lists in 1-Sided or 2Sided mode.
Post Inserter Settings
Specify the paper tray, paper type, or paper size
when using the Post Inserter. This button appears
only when the Post Inserter is installed.
Auto Color Level Adjust.
Adjust the reference level for detecting a color or black-and-white original
when the Auto Color setting is selected.
Power Save Settings
Refer to page 7-3.
Output Settings
Refer to page 7-4.
AE Level Adjustment
Refer to page 7-9.
bizhub C652/C652DS/C552/C552DS/C452
Appears when user access is permitted under
Administrator settings.
6-3
6.1
System Settings
6
Settings
Auto Paper Select for Small
Original
Specify the paper size to be used for a case where the document placed
on the original glass is too small to be detected in Auto Paper mode.
Copy on Small Size
Prints on 5-1/2 e 8-1/2 (A5) paper.
• If 5-1/2 e 8-1/2 (A5) paper is not loaded in the
tray, a message that instructs you to load 51/2 e 8-1/2 (A5) paper in the bypass tray appears.
Copy on Letter (Copy
on A4)
Prints on 8-1/2 e 11 (A4) paper.
Prohibit Copy
Starts printing when a paper tray is selected manually and the [Start] key is pressed.
Blank Page Print Settings
Appears when user access is permitted under Administrator settings. For
details, refer to page 7-26.
Page Number Print Position
Specify a page number print position when printing page numbers after
configuring 2-sided print or booklet settings. Select whether to print the
page numbers on a same position on all pages or on positions symmetric
with respect to the stapling position.
Select Keyboard
Select the keyboard type displayed by default in the touch panel.
Factory default
Language Selection
English
Measurement Unit Settings
This value varies depending on the area.
Auto Tray Selection Settings
Tray Priority
Tray 1 ö Tray 2 ö Tray 3 ö Tray 4 ö LCT
LCT is displayed when the optional LCT is installed.
Auto Tray Switch ON/OFF
Restrict
No Matching Paper in Tray
Setting
Stop Printing (Tray Fixed)
Print Lists
•
•
Post Inserter Settings
Paper Tray: F1
Paper Type: Plain Paper
Paper size: Auto Detect
Paper Type
Plain paper
Paper Size
Auto Detect
Auto Color Level Adjust.
Standard (3)
Low Power Mode Settings
15 min.
Sleep Mode Settings
30 min.
Print/Fax Output Settings
Print: Page Print
Fax: Batch Print
Output Tray Settings
• Copy: Tray 2
• Print: Tray 2
• Print Reports: Tray 1
• Fax: Tray 1
[Output Tray] is displayed when the Finisher FS-526, Finisher FS-527, or
Job Separator JS-504 is installed.
[Tray 3] is displayed if the Job Separator JS-603 is installed in the Finisher
FS-527.
AE Level Adjustment
Standard (2)
Auto Paper Select for Small
Original
Prohibit Copy
Blank Page Print Settings
Do Not Print
Page Number Print Position
Left & Right Bind: All the Same
Top & Bottom Bind: All the Same
bizhub C652/C652DS/C552/C552DS/C452
Tray 1
1-Sided
6-4
6.1
System Settings
6
Factory default
Select Keyboard
Local Keyboard
d Reference
To enable Auto Paper:
Press [Basic] ö [Paper] ö [Auto Paper].
To enable Auto Color:
Press [Basic] ö [Color] ö [Auto Color].
To configure Background Removal to Auto:
Press [Quality/Density] ö [Background Removal] ö [Auto].
bizhub C652/C652DS/C552/C552DS/C452
6-5
6.2
6.2
Custom Display Settings
6
Custom Display Settings
Change the touch panel display to the convenience of the user.
%
Press the [Utility/Counter] key ö [User Settings] ö [Custom Display Settings].
Settings
Copier Settings
Default Tab
Select either the standard Basic tab or the Quick
Copy tab as the basic settings screen in Copy
mode.
Shortcut Key 1
Allocate shortcut keys for frequently used Application functions to be added to the basic settings
screen. Pressing a shortcut key displays the desired setting screen.
• When the optional image controller is installed, only one shortcut key can be enabled.
Shortcut Key 2
Quick Settings 1
Quick Settings 2
Quick Settings 3
Quick Settings 4
Default Tab Density
Settings
Allows you to register setting conditions for frequently used copy functions and place them on
the basic settings screen. The registered setting
condition can be invoked by only pressing the
corresponding easy setting key.
Specify whether to display the copy density setting in the basic settings screen. If [ON] is selected, you can press [Dark] or [Light] in the basic
settings screen to adjust the copy density.
• If [ON] is selected, [Quick Settings 3] and
[Quick Settings 4] cannot be specified.
Scan/Fax Settings
This setting is for the network scan, fax, and network fax operations. For
details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
User Box Settings
Configure settings for the User Box operations. For details, refer to the
"User's Guide [Box Operations]".
Copy Screen
Configure whether to display the [Next Box Job], [Next Scan/Fax Job], or
[Next Copy Job] button or messages when you program the next job during the printing operation.
FAX Active Screen
This setting is for the fax and network fax operations. For details, refer to
the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Color Selection Settings
Select the color used for indicating that the button is selected.
Left Pane Display Default
Left Panel Display
Default
Configure whether to display a list of jobs in process and in queue or to display the contents of the
current Copy settings as the default display of the
left panel.
Job Display Setting
Configure whether to display a list of jobs in process and in queue or to display the progress of the
current job in process, when the default display of
the left panel set to "Job List".
bizhub C652/C652DS/C552/C552DS/C452
6-6
6.2
Custom Display Settings
6
Settings
Search Option Settings
This setting is for the network scan, fax, and network fax operations. For
details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Factory default
Default Tab
Basic
Shortcut Key 1/Shortcut
Key 2/Quick settings
1/Quick settings 2/Quick
settings 3/Quick settings 4
OFF
Default Tab Density Settings
OFF
Default Tab (Fax/Scan Settings)
Address Book
Program Default
(Fax/Scan Settings)
PAGE1
Address Book Index Default
(Fax/Scan Settings)
Favorites
Shortcut Key 1/Shortcut
Key 2
(Fax/Scan Settings)
OFF
Default Address Book
(Fax/Scan Settings)
Index
Default Address Type
(Fax/Scan Settings)
Group
Default Tab (User Box Settings)
Public
Shortcut Key 1/Shortcut
Key 2 (User Box Settings)
OFF
Copy Operating Screen
No
Color Selection Settings
Green
Left Panel Display Default
Job List
Job Display Setting
List Display
Uppercase and lowercase
letters
Differentiate
Search Option Screen
OFF
bizhub C652/C652DS/C552/C552DS/C452
6-7
6.3
6.3
Copier Settings
6
Copier Settings
Configure the settings used by the copy functions.
%
Press the [Utility/Counter] key ö [User Settings] ö [Copier Settings].
Settings
Auto Booklet ON when
Fold & Staple
Configure whether to automatically specify Booklet when Center Staple
and Fold is selected.
This item is displayed if the saddle stitcher is installed in the finisher.
Auto Zoom for Combine/Booklet
Configure whether the preset zoom ratios are automatically selected when
Combine or Booklet is selected in Auto Paper mode.
• Select the recommended zoom ratios for the following zoom settings:
2 in 1, Booklet: 64.7% (70.7%)
4 in 1: 50.0%
8 in 1: 32.3% (35.3%)
Auto Sort/Group Selection
Configure whether to output the copied pages automatically in Sort mode
when copying multiple-page original using the ADF.
Default Copy Settings
Configure the initial values for the Copy function to be displayed when the
power in turned on or the [Reset] key is pressed.
Current Setting
The current settings are used as the default settings.
Factory Default
The factory settings are used as the default settings.
Default Enlarge Display
Settings
This setting is for the enlarged display screen operations. For details, refer
to the "User's Guide [Enlarge Display Operations]".
When AMS Direction is Incorrect
Configure whether to print or discard the job when the original orientation
does not match that of paper in Auto Zoom mode.
Separate Scan Output
Method
Configure the output for divided original loaded in the ADF or for multiple
pages of the original scanned on the original glass.
Page Print
Printing of copies that can be printed begins while
the original is being scanned.
Batch Print
Printing begins after all pages of the original have
been scanned.
Enlargement Rotation
Configure whether to rotate and print a large-size original image when the
original orientation does not match that of paper.
Auto Zoom (Platen)
Appears when user access is permitted under Administrator settings. For
details, refer to page 7-43.
Auto Zoom (ADF)
Specify Default Tray when
APS Off
Select Tray for Insert Sheet
Tri-Fold Print Side
bizhub C652/C652DS/C552/C552DS/C452
This item is displayed when user access is allowed in Administrator settings while the Finisher FS-526 is installed. For details, refer to page 7-43.
6-8
6.3
Copier Settings
6
Settings
Half-Fold/Tri-Fold Specification
Specify whether to apply Half-Fold/Tri-Fold for all pages together or for
specific pages when handling a job containing multiple pages.
When Booklet is selected simultaneously with Half-Fold, all pages are halffolded together even if [One Sheet at a Time] is selected.
If the number of original pages exceeds the folding capacity of this machine, the "Fold" function setting is cancelled automatically, and the sheets
are printed without being folded.
This item is displayed if the Saddle Stitcher SD-508 is installed in the Finisher FS-526.
To change the folding capacity, contact your service representative.
Half-folding capacity setting: 1-3 (default:3)
Tri-folding capacity setting: 1-3 (default:1)
Half-Fold Specification
Specify whether to apply Half-Fold together for all pages or for each page
when handling a job containing multiple pages.
When Booklet is selected simultaneously with Half-Fold, all pages are halffolded together even if [One Sheet at a Time] is selected.
If the number of original pages exceeds the folding capacity of this machine, the "Fold" function setting is cancelled automatically, and the sheets
are printed without being folded.
This item is displayed if the Saddle Stitcher SD-509 is installed in the Finisher FS-527.
To change the folding capacity, contact your service representative.
Half-folding capacity setting: 1-3 (default:3)
Print Jobs During Copy
Operation
Appears when user access is permitted under Administrator settings. For
details, refer to page 7-43.
Automatic Image Rotation
Finishing Program
Configure whether to display the Finishing Program button in the basic settings screen. To display the button, register the contents of the finishing
program.
Register frequently used finishing functions so that you can set them at
once by using the button that appears in the basic settings screen.
This item is set if the finisher is installed.
Card Shot Settings
Appears when user access is permitted under Administrator settings. For
details, refer to page 7-43.
Factory default
Auto Booklet ON when
Fold & Staple
Auto Select Booklet
Auto Zoom for Combine/Booklet
Auto Display Zoom Ratio
Auto Sort/Group Selection
Yes
Default Copy Settings
Factory Default
When AMS Direction is Incorrect
Print
Separate Scan Output
Method
Page Print
Enlargement Rotation
Allow
Auto Zoom (Platen)
OFF
Auto Zoom (ADF)
ON
Specify Default Tray when
APS Off
Tray Before APS ON
Select Tray for Insert Sheet
Tray 2
Tri-Fold Print Side
Inside
Half-Fold/Tri-Fold Specification
Multiple Sheets
Half-Fold Specification
Multiple Sheets
bizhub C652/C652DS/C552/C552DS/C452
6-9
6.3
Copier Settings
6
Factory default
Print Jobs During Copy
Operation
Accept
Automatic Image Rotation
When Auto Paper/Auto Zoom Is Set
Finishing Program
ON
Card Shot
Layout: Top/Bottom
Zoom: Full Size
Store Original Size: X: 3-1/2 inch (89.0 mm) Y: 21 inch (51.0 mm)
bizhub C652/C652DS/C552/C552DS/C452
6-10
6.4
6.4
Fax/Scan Settings
6
Fax/Scan Settings
This setting is for the network scan, fax, and network fax operations. For details, refer to the "User's Guide
[Network Scan/Fax/Network Fax Operations]".
bizhub C652/C652DS/C552/C552DS/C452
6-11
6.5
6.5
Printer Settings
6
Printer Settings
This setting is for the printer operations. For details, refer to the "User's Guide [Print Operations]".
bizhub C652/C652DS/C552/C552DS/C452
6-12
6.6
6.6
Change Password
6
Change Password
Change the password for the user who is currently logged in.
0
A public user cannot use this function.
1
Press the [Utility/Counter] key ö [User Settings] ö [Change Password].
2
Enter the previous password, and then press [OK].
3
Enter a new password.
4
Press [Password Confirmation], and then enter the new password again.
5
Press [OK].
The new password is registered.
bizhub C652/C652DS/C552/C552DS/C452
6-13
6.7
6.7
Change E-Mail Address
6
Change E-Mail Address
Change the E-mail addresses specified as registered user information.
0
0
When logged in as a registered user, you can change the E-mail address.
Appears when user access is permitted under Administrator settings. For details, refer to page 7-50.
1
Press the [Utility/Counter] key ö [User Settings] ö [Change E-Mail Address].
2
Press [E-mail Address].
3
Change the E-mail address.
4
Press [OK].
bizhub C652/C652DS/C552/C552DS/C452
6-14
6.8
6.8
Change Icon
6
Change Icon
Change the icon specified as registered user information.
0
When logged in as a registered user, you can change the E-mail address.
1
Press the [Utility/Counter] key ö [User Settings] ö [Change Icon].
2
Select the icon and press [OK].
bizhub C652/C652DS/C552/C552DS/C452
6-15
6.9
6.9
Register Authentication Information
6
Register Authentication Information
Register or delete the biometric authentication information or IC card authentication information about the
registered users.
You can register or delete authentication information when performing the following operations.
0
0
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Restrict User Access] ö
[Restrict Access to Job Settings] ö [Biometric/IC Card Info. Registration] ö [Allow].
Select [Utility/Counter] ö [Administrator Settings] ö [User Authentication/Account Track] ö [User
Authentication Settings] ö [User Registration] ö [Function Permission] ö [Biometric/IC Card Info.
Registration] ö [Allow].
Log in as a registered user.
1
Select Utility/Counter ö [User Settings] ö [Register Authentication Settings].
2
Press [Edit].
0
To delete authentication information, press [Delete].
For biometric authentication
For IC card authentication
bizhub C652/C652DS/C552/C552DS/C452
6-16
6.9
Register Authentication Information
3
6
Register authentication information.
For biometric authentication, place your finger on the Authentication Unit to scan the finger vein pattern.
Scan the finger vein pattern three times; reset the same finger each time and then press [Scan] for each
scanning.
After scanning the finger vein patterns, place the same finger on the authentication unit, and press
[Authentication Test].
If your finger vein patterns have been authenticated in the authentication test, press [Register]. If
authentication has failed, retry scanning the finger.
For IC card authentication, place your IC card on the Authentication Unit, and press [OK].
4
Press [Close].
bizhub C652/C652DS/C552/C552DS/C452
6-17
6.10
6.10
Cellular Phone/PDA Setting
6
Cellular Phone/PDA Setting
Configure settings to print data in a cellular phone or PDA through this machine. For details, refer to the
"User's Guide Box Operations" and "User's Guide Print Operations".
bizhub C652/C652DS/C552/C552DS/C452
6-18
7
Administrator Settings
7
7
Administrator Settings
Administrator Settings are used only by the administrator to adjust the settings. Logging on to Administrator
Settings requires the administrator password.
Settings
System Settings
Configure the basic functions of this machine.
Administrator/Machine
Settings
Register administrator information and E-mail address of this machine.
One-Touch/User Box Registration
Configure settings for the User Box, network scan, fax, and network fax
operations.
User Authentication/Account Track
Configure the authentication settings to restrict the functions of this machine.
Network Settings
Configure settings for the software, cellular phone, or PDA that can be accessed with this machine.
Copier Settings
Configure the settings for copy functions to be used in copy operations.
Printer Settings
Configure settings for the print operations.
Fax Settings
Configure settings for the fax and network fax operations.
System Connection
Configure network settings.
Security Settings
Configure settings to restrict the functions of this machine for processing
secret data.
License Settings
Enable an optional i-Option function.
OpenAPI Authentication
Management Settings
Configure settings to prevent our deprecated OpenAPI connection application from being registered in this machine.
bizhub C652/C652DS/C552/C552DS/C452
7-2
7.1
7.1
System Settings
7
System Settings
Configure the basic functions of this machine.
7.1.1
Power Save Settings
Configure the settings for the power-saving mode.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Power Save
Settings].
Settings
Low Power Mode Settings
Enter a time period before switching to the lower power mode when this
machine is not being operated.
Sleep Mode Settings
Enter a time period before switching to the sleep mode when this machine
is not being operated.
Power Save Key
Configure the type of the power save function to be started when you press
the [Power Save] key.
Enter Power Save Mode
Low Power
Provides power-saving effect higher than normal.
Sleep
Although this machine conserves more energy in
the sleep mode than in the power save mode, the
machine must warm-up when the sleep mode is
canceled, therefore taking more preparation time
than the power save mode.
Configure settings for switching to the power save mode after printing documents from computers or receiving faxes.
Normal
Enters the power save mode when the time specified in Low Power Mode Settings has elapsed.
Immediately
Enters the power save mode in a short time.
Factory default
Low Power Mode Settings
15 minutes
Sleep Mode Settings
30 minutes
Power Save Key
Lower
Enter Power Save Mode
Immediately
bizhub C652/C652DS/C552/C552DS/C452
7-3
7.1
7.1.2
System Settings
7
Output Settings
Configure the settings for the output functions.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Output Settings].
Settings
Print/Fax Output Settings
This setting is for the print and fax operations. For details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]" and " User's
Guide [Print Operations]".
Output Tray Settings
Configure an output tray given priority for outputting by function.
This item is displayed when the Finisher or Job Separator JS-504 is installed.
Shift Output Each Job
Select whether to shift the output paper for each job.
This item is displayed when the Finisher or Job Separator JS-504 is installed.
Factory default
Print/Fax Output Settings
Print: Page Print
Fax: Batch Print
Output Tray Settings
• Copy: Tray 2
• Print: Tray 2
• Print Reports: Tray 1
• Fax: Tray 1
[Tray 3] is displayed when the Job Separator JS-603 is installed in the Finisher FS-527.
Shift Output Each Job
Yes
bizhub C652/C652DS/C552/C552DS/C452
7-4
7.1
7.1.3
System Settings
7
Date/Time Settings
Configure the current date and time and the time zone.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Date/Time Settings].
Settings
Year
Configure the current date and time.
Monthly
Daily
Hour
Minute
Time Zone
Configure the UTC (Coordinate Universal Time) related time zone.
Factory default
Time Zone
+00:00
d Reference
To cancel the current settings:
Press the [C] key.
bizhub C652/C652DS/C552/C552DS/C452
7-5
7.1
7.1.4
System Settings
7
Daylight Saving Time
Configure daylight saving time settings.
0
This function is available when this machine is connected to the network where UTC (Coordinate
Universal Time) is specified. For details, refer to the "User's Guide [Network Administrator]".
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Daylight Saving
Time].
Settings
Configure whether to use daylight saving time and the time difference from UTC (Coordinate Universal
Time).
Factory default
Daylight Saving Time
bizhub C652/C652DS/C552/C552DS/C452
No
7-6
7.1
7.1.5
System Settings
7
Weekly Timer Setting
Configure the weekly timer in order to allow you to turn on and off this machine at the specified date and time.
0
An exact date/time setting must be performed in advance.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Weekly Timer
Settings].
Settings
Weekly Timer ON/OFF Settings
Configure whether to use the weekly timer function.
Time Settings
Configure the time of each day of the week to turn on and off this machine.
Date Settings
Set All
The setting for the selected day of the week is applied to the same day of the week in other weeks.
Delete
Cancels the selected input value.
Configure the days when timer operation is activated individually. To cancel the setting, press the same day again.
Daily Setting
Configure the days of the week when the timer
operation is activated.
Select Time for Power
Save
Configure the time to turn this machine off and on if you want to turn it off
at a specific time, for example, during a lunch break.
Password for Non- Business Hours
Configure whether to require a user to enter the password if the user uses
this machine outside the specified time.
• To make the user to enter the password, you need to specify the password.
Factory default
Weekly Timer ON/OFF Settings
OFF
Select Time for Power
Save
No
Password for Non-Business Hours
No
bizhub C652/C652DS/C552/C552DS/C452
7-7
7.1
7.1.6
System Settings
7
Restrict User Access
Restrict the machine operation, or change or delete the copy programs by the user.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Restrict User
Access].
Settings
Copy Program Lock Settings
Configure the registered copy programs that are prevented from being
changed or deleted.
Delete Saved Copy Program
Delete the registered copy programs.
Restrict Access to Job Settings
Configure whether to allow users to configure the following settings.
Restrict Operation
Changing Job Priority
Configure whether to allow users to change the
print priority of jobs.
Delete Other User
Jobs
Configure whether to allow other users to delete
jobs when the user authentication settings have
been specified.
Registering and
Changing Addresses
This setting is for the network scan, fax, and network fax operations.
For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
Changing Zoom Ratio
Configure whether to allow users to change registered zoom ratios.
Changing the "From"
Address
This setting is for the network scan operations.
For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
Change Registered
Overlay
Configure whether to allow users to change registered image overlays.
Biometric/IC Card Info. Registration
Configure whether to allow a registered user to
register or delete biometric authentication information or IC card authentication information of
the user.
Restrict Broadcasting
This setting is for the network scan, fax, and network fax operations.
For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
Factory default
Changing Job Priority
Allow
Delete Other User Jobs
Restrict
Registering and Changing
Addresses
Allow
Changing Zoom Ratio
Allow
bizhub C652/C652DS/C552/C552DS/C452
7-8
7.1
System Settings
7
Factory default
7.1.7
Changing the "From" Address
Restrict
Change Registered Overlay
Allow
Biometric/IC card Information Registration
Restrict
Restrict Broadcasting
OFF
Expert Adjustment
Make adjustments so that output quality is increased.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment].
Settings
AE Level Adjustment
Configure the initial value for AE (auto exposure). The higher the setting,
the more that the original background is emphasized.
Printer Adjustment
Adjust the starting print position and defective print images caused by paper type features.
d Reference
The starting print position is factory-adjusted. Normally, you
are not required to change the set values.
bizhub C652/C652DS/C552/C552DS/C452
Leading Edge Adjustment
p. 7-13
Centering
p. 7-13
Leading Edge Adjustment (Duplex Side 2)
p. 7-13
Centering (Duplex 2nd Side)
p. 7-13
Erase Leading Edge
Adjust leading edge erase width.
For details on displaying this item,
contact your service representative.
Vertical Adjustment
Adjust the feed direction zoom ratio of
paper types.
For details on displaying this item,
contact your service representative.
Media Adjustment
p. 7-14
7-9
7.1
System Settings
7
Settings
Finisher Adjustment
Adjust the staple, folding, and punch position of the finisher.
This button appears only when the finisher is installed.
d Reference
Create a sample in advance, and then adjust them while
checking the sample.
Center Staple Position
p. 7-14
Half-Fold Position
p. 7-15
Tri-Fold Position Adjustment
p. 7-15
(This item is displayed when the Finisher FS-526 and Saddle Stitcher SD508 are installed.)
Punch Vertical Position Adjustment
p. 7-16
(This item is displayed when the Finisher FS-526 and Punch Kit PK-516
are installed.)
Punch Horizontal Position Adjustment
p. 7-16
Punch Regist Loop Size Adjustment
p. 7-17
Punch Edge Sensor Adjustment
p. 7-17
(This item is displayed when the Finisher FS-526 and Punch Kit PK-516
are installed.)
Vertical Punch (Z-Fold) Position
Adjustment
p. 7-17
(This item is displayed when Z Folding
Unit is installed.)
Horizontal Punch (Z-Fold) Position Adjustment
p. 7-18
(This item is displayed when Z Folding
Unit is installed.)
1st Z-Fold Position Adjustment
p. 7-18
(This item is displayed when Z Folding
Unit is installed.)
2nd Z-Fold Position Adjustment
p. 7-19
(This item is displayed when Z Folding
Unit is installed.)
Punch Unit Size Detect Sensor
p. 7-19
(This item is displayed when Z Folding
Unit is installed.)
Post Inserter Tray Size Adjustment
Adjust the paper size to be used in the
Post Inserter. You can specify different paper sizes for the upper and lower trays. This button appears when the
Post Inserter PI-505 is installed.
Density Adjustment
Correct the toner amount to be used by color depending on the paper
type.
• To correct the toner amount to be used in the black print mode, press
[Black Image Density].
Image Stabilization
Image Stabilization Only
bizhub C652/C652DS/C552/C552DS/C452
Press the [Start] key to stabilize images.
Pressing the [Image Stabilization Only]
button executes normal image stabilization.
If a good result was not achieved after
the [Image Stabilization Only] button
was pressed, execute [Initialize + Image Stabilization].
7-10
7.1
System Settings
7
Settings
Image Stabilization Setting
Specify the type and opportunity of
image stabilization. If [Standard] is selected, normal stabilization is performed during warm-up processing
when a change in the absolute humidity has been detected during warm-up
processing.
If [Color Priority] is selected, color stabilization is performed when the power has been turned on.
Selecting [Black & White Priority] executes monochrome stabilization during warm-up when absolute humidity
change is detected during the warmup, and then stabilizes color before
performing color print.
Paper Separation Adjustment
Adjust the paper position where the two sides are separated for 2-sided
print.
Color Registration Adjust
Correct color shifts if they are detected in the print result.
For details, refer to page 7-20.
Gradation Adjustment
Adjust irregular gradation levels of print images.
For details, refer to page 7-21.
Image Stabilization Only
Stabilize the image by pressing the
[Start] key before performing gradation adjustment.
Print
Adjust the gradation when the color
gradation has been changed in a print
image. This function performs adjustment, emphasizing the gradation expression of an image and the
reproducibility of texts or lines.
Copy
Adjust the gradation when the color
gradation has been changed in a print
image. This function performs adjustment to save as many images as possible in memory.
Scanner Area
Adjust the scan range of the scanner.
For details on displaying this item, contact your service representative.
ADF Adjustment
Make adjustments for scanning images in the ADF.
For details on displaying this item, contact your service representative.
Line Detection
Prior Detection Setting
(bizhub C652/C552/C452)
Configure whether to issue an alert
when the slit glass is dirty.
• Select an alert display format and
contamination detection level.
Prior Detection Setting (front)
(bizhub C652DS/C552DS)
Configure whether to issue an alert
when the slit glass (front) is dirty.
• Select an alert display format and
contamination detection level.
Prior Detection Setting (back)
(bizhub C652DS/C552DS)
Configure whether to issue an alert
when the slit glass (back) is dirty.
• Select an alert display format, contamination detection level and display timing.
Feed Cleaning Settings
Configure whether to remove a dirt on
the slit glass each time one sheet of
paper passes through the ADF when
scanning an original using the ADF.
Trail Edge Adjust
bizhub C652/C652DS/C552/C552DS/C452
Correct a shift if it is detected at the trailing edge of the print result.
Place, 11 e 17 w, 8-1/2 e 11 v, A3 w, or A4 v on the bypass tray, and
then press the [Start] key to print a test pattern.
7-11
7.1
System Settings
7
Settings
User Paper Settings
Configure special paper settings for User Paper 1 through 6. Settings to
configure include Basic Weight and Media Adjustment.
For details on displaying this item, contact your service representative.
Erase Adjustment
Non-Image Area Erase Operation Settings
Configure Non-Image Area operation
settings.
[Auto]:
Automatically detects the background
density of the original, and selects either "Bevel" or "Rectangular" accordingly.
[Specify]:
Allows you to manually specify an
erase method and original density. As
an erase method, select "Bevel" or
"Rectangular". Specify an original
density from five levels.
Factory default
AE Level Adjustment
Standard (2)
Leading Edge Adjustment
0.0 mm
Centering
0.0 mm
Leading Edge Adjustment
(Duplex Side 2)
0.0 mm
Centering (Duplex 2nd
Side)
0.0 mm
Media Adjustment
Auto
Center Staple Position
0.0 mm
Half-Fold Position
0.0 mm
Tri-Fold Position Adjustment
0.0 mm
Punch Vertical Position Adjustment
0.0 mm
Punch Horizontal Position
Adjustment
0.0 mm
Punch Regist Loop Size
Adjustment
For Finisher FS-526
Finisher: 0.0 mm
Finisher (for Z folding): 0.0 mm
Post inserter feeder (Upper tray): 0.0 mm
Post inserter feeder (Lower tray): 0.0 mm
For Finisher FS-527: 0
Vertical Punch (Z-Fold) Position Adjustment
0.0 mm
Horizontal Punch (Z-Fold)
Position Adjustment
0.0 mm
1st Z-Fold Position Adjustment
0.0 mm
2nd Z-Fold Position Adjustment
0.0 mm
Post Inserter Tray Size Adjustment
Auto Detect
Density Adjustment
0
Image Stabilization Only
Image Stabilization Only
Image Stabilization Setting
Standard
Paper Separation Adjustment
0.0 mm
bizhub C652/C652DS/C552/C552DS/C452
7-12
7.1
System Settings
7
Factory default
Color Registration Adjust
0 dot
Prior Detection Setting
Yes
Warning Display: TYPE1
Detection Level: Std.
Prior Detection Setting
(front)
Yes
Warning Display: TYPE1
Detection Level: Std.
Prior Detection Setting
(back)
Feed Cleaning Settings
Remove
Non-Image Area Erase Operation Settings
Erase Operation: Specify
Erase Method: Rectangular
Original Density: 3
Leading Edge Adjustment
Adjust the starting print position at the leading edge of each type of paper (with respect to the paper feed
direction).
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Printer Adjustment] ö [Leading Edge Adjustment].
% To adjust the starting print position at the leading edge of the second side for 2-sided printing (with
respect to the paper feed direction), press [Leading Edge Adjustment (Duplex Side 2)].
2
Select a paper type to be adjusted.
3
Load the paper into the bypass tray.
4
Press the [Start] key.
A test pattern is printed.
5
Check that the distance from the starting print position of the test
pattern to the edge of the paper (a) is 4.2 mm.
% Press [+] or [-] to adjust the width.
Press the [Start] key to print a test pattern.
6
a
Press [OK].
a:4.2mm
Centering
Adjust the starting print position at the left edge of each paper tray (with respect to the paper feed direction).
0
Only 8-1/2 e 11 v (A4 v) paper can be used to adjust the bypass tray.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Printer Adjustment] ö [Centering].
% To adjust the starting print position at the left edge of the second side for 2-sided printing (with
respect to the paper feed direction), press [Centering (Duplex 2nd Side)].
2
Select a paper tray to be adjusted.
3
Press the [Start] kay.
A test pattern is printed.
bizhub C652/C652DS/C552/C552DS/C452
7-13
7.1
System Settings
4
7
Check that the distance from the starting print position of the test
pattern to the left edge of the paper (b) is 3.0 mm (+/-0.5 mm).
b
% Press [+] or [-] to adjust the width.
Press the [Start] key to print a test pattern.
5
Press [OK].
b:3.0mm±0.5mm
Media Adjustment
Adjust defective print images caused by paper type features.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Printer Adjustment] ö [Media Adjustment].
2
Select a paper type to be adjusted.
% If defective images exist on the back side of 2-sided copy paper, select [2nd Side].
3
Press [+] or [-] to specify an adjusted value.
% If missing parts or white spots exist in print images, press [-]. If the surface of the print image is
rough, press [+].
4
Press [OK] ö [Close].
5
Copy, and then check the print image.
Center Staple Position
Adjust the stapling position for each paper size when printing with the center staple function.
0
0
0
0
Adjust the half-fold position before adjusting the center stapling position.
Before making any adjustments, create a sample using the center staple function. Adjust the center
staple position while checking the created sample.
It can be adjusted only when the saddle sticher is installed.
When stapling in parallel with the left edge of paper, contact your service representative.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Center Staple Position].
2
Select the size of paper of which the center staple position is adjusted.
3
Press [+] or [-] to adjust the staple position while checking the sample.
4
Press [OK].
5
Create a sample, and check the print result.
bizhub C652/C652DS/C552/C552DS/C452
7-14
7.1
System Settings
7
d Reference
To adjust the half-fold position:
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [Half-Fold Position].
Half-Fold Position
Adjust the center staple & fold and half-fold positions.
0
0
0
Before making any adjustments, create a sample using the half-fold function. Adjust the half-fold
position while checking the created sample.
It can be adjusted only when the saddle sticher is installed.
When adjusting the half-fold position in parallel with the left edge of paper, contact your service
representative.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Half-Fold Position].
2
Select the size of paper of which half-fold position is adjusted.
3
Press [+] or [-] to adjust the punched hole position while checking the sample.
4
Press [OK].
5
Create a sample, and check the print result.
Tri-Fold Position Adjustment
Adjust the folding position for each paper size when printing with the tri-fold function. The folding width
depends on the paper size, which cannot be changed.
0
0
Before making any adjustments, create a sample using the tri-fold function. Adjust the tri-fold position
while checking the created sample.
It can be adjusted when the Finisher FS-526 and Saddle Stitcher SD-508 are installed.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Tri-Fold Position Adjustment].
2
Select the size of paper of which tri-fold position is adjusted.
3
Press [+] or [-] to adjust the tri-fold position while checking the sample.
4
Press [OK].
5
Create a sample, and check the print result.
bizhub C652/C652DS/C552/C552DS/C452
7-15
7.1
System Settings
7
Punch Vertical Position Adjustment
Adjust the vertical position of the punched holes for each paper size.
0
0
Before making any adjustments, create a sample using the punch settings. Adjust the punched hole
position while checking the created sample.
This adjustment is available if the Finisher FS-526 and Punch Kit PK-516 are installed.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Punch Vertical Position Adjustment].
2
Select the paper size to adjust the vertical punch position.
3
Press [+] or [-] to adjust the punched hole position while checking the sample.
4
Press [OK].
5
Create a sample, and check the print result.
Punch Horizontal Position Adjustment
Adjust the horizontal position of the punched holes. Adjust the horizontal position of the punched holes as
appropriate for each installed option or paper type.
0
0
0
1
Before making any adjustments, create a sample using the punch settings. Adjust the punched hole
position while checking the created sample.
The horizontal position of the punched holes can be adjusted as appropriate for each installed option
if the finisher FS-526, punch kit PK-516, and post inserter are installed.
This adjustment is available for each paper type if the Finisher FS-527 and Punch Kit PK-517 are
installed.
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Punch Horizontal Position Adjustment].
% Select an option to adjust the horizontal position of the punched holes if the post inserter is installed.
% First, select the paper type if the finisher FS-527 and punch kit PK-517 are installed.
2
Press [+] or [-] to adjust the punched hole position while checking the sample.
3
Press [OK].
4
Create a sample, and check the print result.
bizhub C652/C652DS/C552/C552DS/C452
7-16
7.1
System Settings
7
Punch Regist Loop Size Adjustment
Correct the orientation of the paper and adjust the punched hole position to be parallel with the left edge of
the paper. The punched hole array is corrected by adjusting the resistance applied to the paper for each
paper type.
0
This adjustment is available if the punch kit is installed.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Punch Regist Loop Size Adjustment].
First select the option to adjust the inclination of punch holes when the Finisher FS-526 and Post
Inserter PI-505 or Z Folding Unit ZU-606 are installed.
2
Select a paper type for which the punch hole angle is adjusted.
3
Press [+] or [-] to adjust the punched hole position.
4
Press [OK].
5
Create a sample, and check the print result.
Punch Edge Sensor Adjustment
If the punch position is displaced depending on the paper tray, the punch kit is automatically adjusted.
0
This adjustment is available if the Finisher FS-526 and the Punch Kit PK-516 are installed.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Finisher Adjustment] ö [Punch Edge Sensor Adjustment].
2
Press the [Start] key.
The punch edge sensor is automatically adjusted.
The adjusted result appears.
Vertical Punch (Z-Fold) Position Adjustment
Adjust the vertical position of the punched holes for each paper size.
0
0
Before making any adjustments, create a sample using the punch settings. Adjust the center staple
position while checking the created sample.
This adjustment is available if the Z Folding Unit is installed.
1
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [Vertical Punch (Z-Fold) Position Adjustment].
2
Select the size of paper of which the vertical punched hole position is adjusted.
3
Press [+] or [-] to adjust the punched hole position while checking the sample.
4
Press [OK].
5
Create a sample, and check the print result.
bizhub C652/C652DS/C552/C552DS/C452
7-17
7.1
System Settings
7
Horizontal Punch (Z-Fold) Position Adjustment
Adjust the horizontal position of the punched holes for each paper size.
0
0
Before making any adjustments, create a sample using the punch settings. Adjust the center staple
position while checking the created sample.
This adjustment is available if the Z Folding Unit is installed.
1
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [Horizontal Punch (Z-Fold) Position Adjustment].
2
Press [+] or [-] to adjust the punched hole position while checking the sample.
3
Press [OK].
4
Create a sample, and check the print result.
1st Z-Fold Position Adjustment
Adjust the first paper folding position for each paper size when using the Z-fold function.
1st Z-Fold Position
0
0
Before making any adjustments, create a sample using the Z-fold function. Adjust the center staple
position while checking the created sample.
This adjustment is available if the Z Folding Unit is installed.
1
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [1st Z-Fold Position Adjustment].
2
While checking the sample, press [+] or [-] to adjust the first folding position.
3
Press [OK].
4
Create a sample, and check the print result.
bizhub C652/C652DS/C552/C552DS/C452
7-18
7.1
System Settings
7
2nd Z-Fold Position Adjustment
Adjust the second paper folding position for each paper size when using the Z-fold function.
2nd Z-Fold Position
0
0
Before making any adjustments, create a sample using the Z-fold function. Adjust the center staple
position while checking the created sample.
This adjustment is available if the Z Folding Unit is installed.
1
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [2nd Z-Fold Position Adjustment].
2
While checking the sample, press [+] or [-] to adjust the second folding position.
% The distance between the left end of paper and the second Z-fold position must be 2 mm or more.
2 mm or more
3
Press [OK].
4
Create a sample, and check the print result.
Punch Unit Size Detect Sensor
If the punch position is displaced depending on the paper tray, the punch unit is automatically adjusted.
0
This adjustment is available if the Z Folding Unit or Punch Kit PK-516 is installed.
1
Select [Utility/Counter] ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment] ö
[Finisher Adjustment] ö [Punch Unit Size Detect Sensor].
2
Press [Start].
% The punch unit edge sensor is automatically adjusted.
% The adjusted result appears.
bizhub C652/C652DS/C552/C552DS/C452
7-19
7.1
System Settings
7
Color Registration Adjust
If color shifts are detected in the print result, adjust the each color print position for each paper type.
0
The procedure for adjusting the color registration is the same for yellow, magenta and cyan.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Color Registration Adjust].
2
Select a color to be corrected.
3
Select a paper type for which color registration is adjusted.
4
Load the paper into the bypass tray.
% The loadable paper size is 11 e 17w, 8-1/2 e 11v, A3 w, or A4 v.
5
Press the [Start] key.
A test pattern is printed.
6
Check that the black line aligns with the color line to be adjusted
at the X and Y positions of the test pattern.
% Press [+] or [-] to adjust the color line to be corrected while checking the sample.
The color registration is adjusted.
7
Press the [Start] key to print a test pattern, and then check the print result.
8
Press [OK].
bizhub C652/C652DS/C552/C552DS/C452
7-20
7.1
System Settings
7
Gradation Adjustment
Adjust irregular gradation levels of print images.
0
Adjust each correction item three times.
1
Turn off the main power switch of this machine.
2
Wait at least 10 seconds, and then turn it on again.
3
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Expert Adjustment]
ö [Gradation Adjustment].
4
Press the [Start] key.
The image stabilization operation starts.
The correction items on the right of the touch panel become enabled.
5
Select an item to be corrected.
6
Select paper used to output a test pattern.
% As a paper size, select 11 e 17w, 8-1/2 e 11v, A3w or A4 v. By default, 11 e 17 w (A3 w) is
selected.
% Paper in the bypass tray cannot be selected.
7
Press the [Start] key.
A test pattern is printed.
% Selecting 11 e 17w or A3w outputs one sheets, and selecting 8-1/2 e 11v or A4v outputs two
sheets.
8
Place the printed test pattern on the original glass in orientation displayed in the touch panel.
% For the test patterns of 8-1/2 e 11v or A4v, place the output two sheets side by side.
9
Place 10 or more sheets of blank paper on top of the test pattern to prevent it from becoming
transparent.
10
Close the ADF.
11
Press the [Start] key.
The test pattern is scanned.
The gradation level is automatically adjusted.
12
Repeat steps 5 through 11 two more times.
bizhub C652/C652DS/C552/C552DS/C452
7-21
7.1
7.1.8
System Settings
7
List/Counter
Configure the job settings list print settings and paper count settings for this machine.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [List/Counter].
Settings
Management List
Job Settings List
Configure paper tray settings for printing the job
settings list and specify a print side.
Paper Size/Type Counter
Register a combination of paper size and paper type for a counter. Every
time the counter is changed, the count is reset to 0.
Counter Clear
Resets the count to 0.
Paper Size
Select the paper size of the counter.
Paper Type
Select the paper type of the counter.
Factory default
Job Settings List
bizhub C652/C652DS/C552/C552DS/C452
•
•
1-Sided
Tray 1
7-22
7.1
7.1.9
System Settings
7
Reset Settings
Configure auto reset settings.
0
0
%
All settings performed in the following tabs during operation using the copy function are automatically
reset to the initial settings after the specified time has elapsed.
Basic tab, Original Setting tab, Quality/Density tab, Application tab
Even if [OFF] is selected for System Auto Reset Time, the system auto reset function operates when
this machine is not used for one minute during user authentication/account track operations.
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Reset Settings].
Settings
System Auto Reset
Priority Mode
Configure a mode to be displayed in the system
auto reset mode.
System Auto Reset
Time
Configure whether to perform system auto reset.
Specify a time until the initial screen appears if
this machine is not operated. The specified time
is not canceled.
d Reference
If user authentication or enhanced security mode is enabled, the administrator settings mode or user
authentication mode is logged off according to the setting for System Auto
Reset Time.
In the enlarge display mode, the system auto reset mode is disabled.
Auto Reset
Configure whether to perform auto reset in the selected mode.
Specify a time until the basic settings screen appears and the settings are
reset to the initial values if this machine is not operated.
Job Reset
When Account is
changed
Configure whether to reset the settings when you
log off if the user authentication or account track
settings have been configured.
When original is set
on ADF
Configure whether to reset the settings when an
original is loaded in the ADF.
Next Job
Configure whether to reset the following settings
when the next job is selected.
• Staple Setting
• Original Set/Bind Direction
• Reset Data After Job
The destination of data is always reset.
bizhub C652/C652DS/C552/C552DS/C452
7-23
7.1
System Settings
7
Factory default
Priority Mode
Copy
System Auto Reset Time
1 minute
Auto Reset
•
•
•
When Account is changed
Reset
When original is set on ADF
Do Not Reset
Next Job
•
•
•
Copy: 1 Minute
Scan/Fax: 1 Minute
User Box: 1 Minute
Staple Setting: OFF
Original Set/Bind Direction: OFF
Reset Data After Job: Reset All
d Reference
To configure user authentication/account track:
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö [General
Settings].
7.1.10
User Box Settings
This setting is for the User Box functions. For details, refer to the "User's Guide [Box Operations]".
7.1.11
Standard Size Setting
Configure settings relating to the capability for detecting original size and the foolscap paper sizes.
For details on displaying this item, contact your service representative.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Standard Size
Setting].
Settings
Original Glass Original Size
Detect
Configure the capability for detecting original sizes.
8-1/2 e 14/Foolscap Size
Detection
European model (cm) only
Specify whether to detect a size of 8-1/2 e 14 or a foolscap size.
• This item may not be displayed on product sales areas.
Foolscap Size Setting
Select the size that you want to use when the paper size is close to 13 inches.
bizhub C652/C652DS/C552/C552DS/C452
7-24
7.1
System Settings
7
Factory default
7.1.12
Original Glass Original Size
Detect
Table 1
8-1/2 e 14 Foolscap Size
Detection
8-1/2 e 14
Foolscap Size Setting
8 e 13 w
Stamp Settings
Configure header and footer settings to be printed.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Stamp Settings].
Settings
Header/Footer Settings
Register or change a header and footer.
To use the header/footer function in Application Setting, a header and
footer must be registered in advance.
New
Enter a registration name, and then configure detailed header and footer settings.
Configure whether to print a header and footer,
and then configure print contents.
• Text: Enter text.
• Date/Time: Select a format to display the date
and time.
• Other: Specify the distribution control
number. Select whether to include the Job
Number, Serial Number, and Account/User
Name.
Configure pages and text details.
• Pages: Select whether to print the header and
footer on all pages or only on the first page.
• Text Details: Select the color, size, and type of
the text for the header and footer to be printed.
Fax TX Settings
Delete
Deletes the selected header or footer.
Check/Edit
Change the selected header or footer.
This setting is for the fax and network fax operations.
For details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Factory default
FAX TX Settings
bizhub C652/C652DS/C552/C552DS/C452
Cancel
7-25
7.1
7.1.13
System Settings
7
Blank Page Print Settings
Configure whether to print stamps or overlay on blank pages.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Blank Page Print
Settings].
Settings
Configure whether to print stamp/composition on blank pages.
Factory default
Blank Page Print Settings
7.1.14
Do Not Print
Skip Job Operation Settings
Configure whether to start processing for the next job when the current job stops due to running out of paper
in the paper tray. Selecting "Yes" provides no print queue time due to job stopping.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Skip Job Operation
Settings].
Settings
Fax
Configure whether to skip a job in the fax mode.
Other than Fax
Configure whether to skip a job in a mode other than the fax mode.
Factory default
Skip Job Operation Settings
bizhub C652/C652DS/C552/C552DS/C452
Fax: Yes
Other than Fax: Yes
7-26
7.1
7.1.15
System Settings
7
Default Bypass Paper Type Setting
Configure the initial settings for the paper type to be used for the bypass tray. The initial setting for the paper
type is applied after the job finishes or the tray runs out of paper.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Default Bypass
Paper Type Setting].
Settings
Configure whether to specify the initial setting for paper type for the bypass tray. When you specified this,
select a paper type.
Factory default
Default Bypass Paper Type
Setting
7.1.16
Yes
Paper Type: Plain Paper
Advanced Preview Setting
Configure settings to fax or scan a document. For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-27
7.1
7.1.17
System Settings
7
Page Number Print Position
Specify a page number print position when printing page numbers after configuring 2-sided print or booklet
settings. Select whether to print the page numbers on a same position on all pages or on positions symmetric
with respect to the stapling position.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [System Settings] ö [Page Number Print
Position].
Settings
Left & Right Bind: All the
Same
Top & Bottom Bind: All the
Same
Select a desired print position.
Left & Right Bind: Symmetrical
Top & Bottom Bind: All the
Same
Left & Right Bind: Symmetrical
Top & Bottom Bind: Symmetrical
Factory default
Page Number Print Position
bizhub C652/C652DS/C552/C552DS/C452
Left & Right Bind: All the Same
Top & Bottom Bind: All the Same
7-28
7.2
7.2
Administrator/Machine Settings
7
Administrator/Machine Settings
Register administrator information and E-mail address of this machine.
0
The device name entered under the Input Machine Address may not be supported by your operating
system.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Administrator/Machine Setting].
Settings
Administrator Registration
Register administrator information displayed on the Service/Admin. Information screen of the Guidance screen and the From address for sending
E-mail from this machine.
Input Machine Address
Register the device name and E-mail address of this machine. The device
name is used as a part of the name of the file created on this machine. The
E-mail address can be used for Internet fax.
Factory default
Device Name
bizhub C652/C652DS/C552/C552DS/C452
The default abbreviation is input for the product name. If necessary, it can
be changed freely.
7-29
7.3
7.3
One-Touch/User Box Registration
7
One-Touch/User Box Registration
This setting is for the User Box, network scan, fax, and network fax operations. For details, refer to the "User's
Guide [Network Scan/Fax/Network Fax Operations]" and "User's Guide [Box Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-30
7.4
7.4
User Authentication/Account Track
7
User Authentication/Account Track
Configure the authentication settings to control the use of this machine.
Type and functions of authentication
User Authentication
Appropriate for controlling users. To allow unregistered users to use this machine, public user settings
are required.
–
Restricts accessible functions.
–
Counts the number of outputting and scanning by user.
–
Limits on using color or black printing and on the number of copies that can be set by user.
–
Operates a Personal User Box for each user and group box.
–
Controls the access allowed level of the destination.
–
Prohibits jobs of other users from being deleted.
Account Track
Appropriate for controlling groups or multiple users.
–
Counts the number of outputting and scanning by account.
–
Limits on using color or black printing and on the number of copies that can be set by account.
–
Operates the group box.
Reference
Either user authentication or account track settings can be configured, or user authentication can be
synchronized with account track. Settings can be configured for the both and used without being
synchronized.
A total of 1,000 users and accounts can be registered.
To register more than 1,000, use PageScope Authentication Manager. You can register up to 30,000
users and accounts.
bizhub C652/C652DS/C552/C552DS/C452
7-31
7.4
7.4.1
User Authentication/Account Track
7
General Settings
Configure the settings for enabling the authentication functions.
0
Before registering a user, select an authentication method. If all management data is cleared after the
authentication method was selected, the histories of the registered users, print, send, receive, and save
jobs are deleted.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[General Settings].
Settings
User Authentication
Public User Access
Configure whether to use user authentication.
OFF
Disables user authentication.
ON (External Server)
Restricts users who can access this machine using the external authentication server. This setting
is available when external authentication server
settings are configured.
ON (MFP)
Restricts users who can access this machine using this machine.
Allows public user accesses when the enhanced security mode is disabled.
Restrict
Prohibits unregistered users from using this machine.
ON (With Login)
A public user can use this machine after pressing
[Public user] in the Login screen to log in to this
machine.
ON (Without Login)
A public user can use this machine without logging in to this machine in the Login screen.
Account Track
ON/OFF
Configure whether to use the account track function.
Account Track Input Method
Select an authentication method when configuring account track settings.
bizhub C652/C652DS/C552/C552DS/C452
Account Name &
Password
Enter the account name and password to log in.
Password Only
Enter only the password to log in.
• You cannot configure this when user authentication settings are configured.
7-32
7.4
User Authentication/Account Track
7
Settings
Synchronize User Authentication & Account Track
Configure the authentication operation settings when both user authentication and account track settings are configured. Configure whether to automatically select the account assigned to the user during logging in.
Synchronize
Allows the user to log in to one account assigned
to the user.
The user who succeeded in user authentication
can log in without account track authentication.
d Reference
This function is appropriate for managing each user by account.
Do Not Synchronize
When # of Jobs Reach
Maximum
Allows the user to log in to some accounts.
The user who succeeded in user authentication
performs account track authentication to log in.
Configure the action of this machine that is taken when the output count of
the job reaches the limit specified for the user or account.
Skip Job
Stops the running job, and then automatically
starts the next job.
Stop Job
Stops all jobs.
Number of User Counters
Assigned
Configure how many of a total of 1,000 users and account registrations
should be allowed for user registration at maximum. The remaining registration number is for accounts.
When user authentication and account track settings are configured, the
number of counters assigned for users can be specified.
Ticket Hold Time Setting
Enter a time to hold the Kerberos authentication tickets. The external server authentication settings are configured, and applied when Active Directory is selected as the authentication server type.
Factory default
User Authentication
OFF
Public User Access
Restrict
Account Track
OFF
Account Track Input Method
Account Name & Password
Synchronize User Authentication & Account Track
Synchronize
When # of Jobs Reach
Maximum
Skip Job
Number of User Counters
Assigned
500
Ticket Hold Time Setting
60 min.
d Reference
To configure external server settings:
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö [External
Server Settings].
For details on enhanced security settings, contact your service representative.
bizhub C652/C652DS/C552/C552DS/C452
7-33
7.4
7.4.2
User Authentication/Account Track
7
User Authentication Settings
Configure the user and user counter management settings.
0
0
When only user authentication settings are configured, User Authentication Setting are enabled.
If only user authentication settings are configured, up to 1,000 users can be registered. If user
authentication and account track settings are configured, up to 500 users can be registered as initial
settings.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[User Authentication Settings].
Settings
Administrative Settings
User Registration
bizhub C652/C652DS/C552/C552DS/C452
User Name List
Configure whether to display a key to display a list
of registered users in the Login screen.
This item is enabled when the enhanced security
settings are disabled.
Default Function Permission
Configure an initial value for function permission
to users who are authenticated on the external
server.
ID & Print Settings
Configure whether to use the ID & print function.
Also configure whether to immediately print unauthenticated jobs or public user job or save it in
the ID & Print User Box.
ID & Print Operation
Settings
Configure whether to print all jobs using one authentication or print jobs one by one if multiple ID
& print jobs are accumulated.
Default Operation
Selection
In the Login screen for user authentication where
ID and print jobs are stored, specify the default
values for the operation to be carried out after authentication has been completed.
When using this machine while the ID & print
function is disabled, the user can select [Access]
to log in to this machine without specifying the
operation to be carried out after authentication.
Register users who can access this machine. Select a desired registration
number, and then press [Edit]. Settings for registered users can be
changed.
• Selecting a user and pressing [Delete] delete the selected user.
• If public user access is allowed, functions available to public users can
be restricted. To change the setting for public users, select the registration number "000".
User Name
Enter a user name.
• Once a user name is registered, it cannot be
changed.
• A user name that has already been registered
cannot be used again.
Password
Enter the password.
E-Mail Address
Enter an E-mail address.
7-34
7.4
User Authentication/Account Track
7
Settings
Account Name
Specify the account track of the registered user
when account track settings are configured,
Before you select an account name, you must
registered it.
Output Permission
Apply the following restrictions to the selected
user or all users.
• Print
Configure whether to allow the user to copy
and print in color and black, respectively.
If black copy or print is restricted, print in
black and white cannot be output.
• Send
Configure whether to allow the user to send
fax and E-mail in color.
d Reference
Single color and 2 color output settings can be changed by the administrator. For details, refer to page 7-41.
bizhub C652/C652DS/C552/C552DS/C452
Max. Allowance Set
Configure the max. allowance for the selected
user or all users. When not specifying it, select
[No Limit].
• Total Allowance
Specify the number of copies that can be output by the user.
• Individual Allowance
Specify the number of black copies and color
copies that can be output by the user.
Auth.-info.registrieren
Press [Edit], and then register authentication information.
This setting is available when the optional authentication unit is installed.
Function Permission
Restrict functions available to the selected user or
all users. Specify whether to allow the following
functions:
• Copy
• Scan
• Fax
• Print
• User Box
• Print Scan/Fax TX
• Save to External Memory
• External Memory Document Scan
• Manual Destination Input (If [Allow] is selected, specify either to allow Manual Destination
Input or manage the destination manually.)
• Limited Color Print (Public user only)
• Biometric/IC Card Regist. Info.
• Mobile/PDA
Pause
Suspends the use of this machine for the selected
user. [Stop Job] is selected, the specified user
cannot log in to this machine.
It is convenient to set suspend for users who do
not use this machine temporarily or who have lost
an IC card, instead of deleting them.
• If [All Users] is selected, you can suspend the
use of this machine for all the registered users.
• If suspend is selected for a specific account,
it is also suspended for users who belong to
that account even if [Continue Job] is selected
for this setting.
Icon
Select an icon.
7-35
7.4
User Authentication/Account Track
7
Settings
User Counter
Reset All Counters
Resets all counters for all users.
Counter Details
Shows the use status for the selected user.
Press [Clear Counter] to reset the counter.
• The public user counter is specified for the
last page.
Factory default
User Name List
OFF
Default Function Permission
Save to External Memory/External Memory Document Scan: Restrict
Other items: Allow
ID & Print Settings
ID & Print: OFF (when the authentication unit is not installed)
ON (when the authentication unit is installed)
Public User: Print Immediately
ID & Print Operation Settings
Print All Jobs
Default Operation Selection
Begin Printing
Output Permission
All Items: Allow
Max. Allowance Set
Individual Allowance: Color No Limit/Black No Limit
Total Allowance: No Limit
Function Permission
Copy: Allow
Scan: Allow
Fax: Allow
Print: Allow
User Box: Allow
Print Scan/Fax TX: Allow
External Memory Document Scan: Restrict
Save to External Memory: Restrict
Manual Destination Input: Allow/Allow All
Limited Color Print: Restrict
Biometric/IC Card Regist. Info.: Restrict
Mobile/PDA: Allow
Pause
Continue Job
Icon
d Reference
To specify the maximum number of registrations for the user:
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö [General
Settings] ö [Number of User Counters Assigned].
bizhub C652/C652DS/C552/C552DS/C452
7-36
7.4
7.4.3
User Authentication/Account Track
7
Account Track Settings
Configure the account and account counter management settings.
0
0
When only account track settings are configured, Account Track Settings is enabled.
If only account track settings are configured, up to 1,000 accounts can be registered. If user
authentication and account track settings are configured, up to 500 accounts can be registered as initial
settings.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[Account Track Settings].
Settings
Account Track Registration
•
•
Select a desired registration number, press [Edit], and then register or
change the account.
Select an account to be deleted, and the press [Delete].
Account name
Specify the account name.
• An account name that has already been registered cannot be used again.
Password
Enter the password.
Output Permission
Apply the following restrictions to the selected
account or all accounts.
• Print
Specify whether to allow color or black copy
or print output to the user of the account.
If black copy or print is restricted, print in
black and white cannot be output.
• Send
Specify whether to allow the account members to send fax or E-mail in color.
d Reference
Single color and 2 color output settings can be changed by the administrator. For details, refer to page 7-41.
Max. Allowance Set
bizhub C652/C652DS/C552/C552DS/C452
Configure the max. allowance for the selected account or all accounts. When not specifying it, select [No Limit].
• Total Allowance
Configure the number of copies that can be
output by a member of the account.
• Individual Allowance
Configure the number of black copies and
color copies that can be output by a member
of the account.
7-37
7.4
User Authentication/Account Track
7
Settings
Account Track Counter
Pause
Suspends the use of this machine for the selected
account. If [Stop Job] is selected, the specified
user cannot log in to this machine.
It is convenient to set suspend for accounts that
do not use this machine temporarily, instead of
deleting them.
• If [All Accounts] is selected, you can suspend
the use of this machine for all registered accounts.
• If [Stop Job] is selected, it is also suspended
for users who are belong to the accounts.
Reset All Counters
Resets all counters for all accounts.
Counter Details
Shows the use status for the selected account.
Press [Clear Counter] to reset the counter.
Factory default
Output Permission
All Items: Allow
Max. Allowance Set
Individual Allowance: Color No Limit/Black No Limit
Total Allowance: No Limit
d Reference
To specify the maximum number of registrations for the account:
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö [General
Settings] ö [Number of User Counters Assigned].
7.4.4
Print without Authentication
This setting is for the print operations. For details, refer to the "User's Guide [Print Operations]".
7.4.5
Print Counter List
Select the paper tray and print format to be used for printing the counter list.
0
This function is enabled when user authentication or account track settings are configured.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[Print Counter List].
Settings
Paper Tray
Select the desired paper tray.
Simplex/Duplex
Select Print (1-Sided) or Print (2-Sided).
Print Item
Configure whether to print all data or printing data only.
bizhub C652/C652DS/C552/C552DS/C452
7-38
7.4
User Authentication/Account Track
7
Factory default
Print Counter List
7.4.6
•
•
•
Paper Tray: Tray 1
Simplex/Duplex:1-Sided
Print Item: All Data
External Server Settings
Configure the external server that performs user authentication.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[External Server Settings].
Settings
Select a number for the desired external server. You can also change the settings for the registered servers.
New/Edit
Server Name
Enter the name of the external server.
Server Type
Configure an external server type, and then configure the settings for required items.
Delete
Delete the selected external server.
Set as Default
Configure an external server specified as the initial value. Select a desired
server, and then press the [Set as Default] button.
d Reference
For details on configuring external server settings, refer to the "User's Guide [Network Administrator]".
7.4.7
Limiting Access to Destinations
This setting is for the network scan, fax, and network fax operations. For details, refer to the "User's Guide
[Network Scan/Fax/Network Fax Operations]", "User's Guide [Network Administrator]".
bizhub C652/C652DS/C552/C552DS/C452
7-39
7.4
7.4.8
User Authentication/Account Track
7
Authentication Device Settings
Configure the authentication operations when the optional authentication unit is installed.
0
This setting is available when the optional authentication unit is installed.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[Authentication Device Settings].
Settings
General Settings
Logoff Settings
bizhub C652/C652DS/C552/C552DS/C452
Card Authentication
Displayed when the Authentication Unit (IC card
type) AU-201 is installed.
• IC Card Type
Select the type of the IC card to be used in this
machine. The FeliCa card ([FeliCa], [SSFC],
[FCF], or [FCF (Campus)]) or Type A card
([Type A]) can be selected. If [FeliCa+Type A],
[SSFC+Type A], [FCF+Type A], or [FCF (Campus)+ Type A] is selected, both the FeliCa and
Type A cards can be used in this machine at
the same time. If [SSFC] or [SSFC+Type A] is
selected, specify [Company Code] or [Company Identification Code].
• Operation Settings
Specify how to log in to this machine. [IC Card
Authentication] allows the user to log in by
simply placing the IC card. [Card Authentication + Password] allows the user to log in by
placing the IC card and entering the password.
Bio Authentication
Displayed when Authentication Unit (biometric
type) AU-101 or Authentication Unit (biometric
type) AU-102 is installed.
• Beep Sound
Specify whether to output a beep when reading the finger vein pattern.
• Operation Settings
Specify how to log in to this machine. [1-tomany authentication] allows the user to log in
by simply placing his or her finger on the authentication unit. [1-to-1 authentication] allows the user to log in by entering the user
name and placing his or her finger on the authentication unit.
Configure whether to log out when scanning of
the original finishes.
7-40
7.4
7.4.9
User Authentication/Account Track
7
User/Account Common Setting
Configure the settings for the logout confirmation screen and settings for single color and 2 color output
management if authentication settings have been configured.
0
This function is enabled if authentication function settings have been configured.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [User Authentication/Account Track] ö
[User/Account Common Setting].
Settings
Logout Confirmation
Screen Display Setting
Configure whether to display the logout confirmation screen when you
press the [Access] key to log out.
Single Color > 2 Color Output Management
Configure whether to manage the output of single color or 2 color as color
print or black print.
When managing it as black print, even a user who is restricted from performing color print can perform single color or 2 color output.
d Reference
For details on output permission for users, refer to page 7-34 or
page 7-37.
Factory default
7.4.10
Logout Confirmation
Screen Display Setting
ON
Single Color > 2 Color Output Management
Color
Scan to Home Settings
This setting is for the network scan operations. For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]""User's Guide [Network Administrator]".
7.4.11
Scan to Authorized Folder Settings
This setting is for the network scan, fax, and network fax operations. For details, refer to the "User's Guide
[Network Scan/Fax/Network Fax Operations]", "User's Guide [Network Administrator]".
bizhub C652/C652DS/C552/C552DS/C452
7-41
7.5
7.5
Network Settings
7
Network Settings
This setting is for the network operations. For details, refer to the "User's Guide [Network Administrator]".
bizhub C652/C652DS/C552/C552DS/C452
7-42
7.6
7.6
Copier Settings
7
Copier Settings
Configure the settings used by the copy functions.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Copier Settings].
Settings
Auto Zoom (Platen)
Configure whether Auto Select is automatically selected when a paper tray
is selected manually while an original is placed on the original glass.
Auto Zoom (ADF)
Configure whether Auto Select is automatically selected when a paper tray
is selected manually while an original is placed in the ADF.
Specify Default Tray when
APS Off
Configure which paper tray to be selected when the APS (Auto Paper) setting is canceled.
Tray Before APS ON
Uses the paper tray specified before the APS was
selected.
Default Tray
Uses Tray 1.
Select Tray for Insert Sheet
Configure the default paper tray loaded with paper for the cover pages
(front cover), inserted sheets and the chapter title pages.
Print Jobs During Copy
Operation
Configure whether to accept print data or fax data while a copy operation
is being performed.
Accept
Accepts print data or fax data to print.
Receive Only
Prints print data or fax data after the copy operation is finished.
Tri-Fold Print Side
Configure whether the printed side is on the inside or the outside when the
page is folded in three.
This function is enabled when the finisher FS-526 and Saddle Sticher SD508 are installed.
Automatic Image Rotation
When the original orientation is different from paper orientation, the image
is rotated depending on the setting. Configure when the image is automatically rotated.
Copy Card Settings
Register card copy setting.
If [Card Copy] is selected in [Application], the function can be invoked with
the registered setting.
Layout
Specify where to place the front and back sides
of a card.
Zoom
Specify to copy a card with the full size or enlarge
an image to fit paper.
Store Original Size
Change and register the pre-specified original
size or [Original Name].
Factory default
Auto Zoom (Platen)
OFF
Auto Zoom (ADF)
ON
bizhub C652/C652DS/C552/C552DS/C452
7-43
7.6
Copier Settings
7
Factory default
Specify Default Tray when
APS Off
Tray Before APS ON
Select Tray for Insert Sheet
Tray 2
Print Jobs During Copy
Operation
Accept
Tri-Fold Print Side
Inside
Automatic Image Rotation
When Auto Paper/Auto Zoom is Set
Card Shot Settings
Layout: Top/Bottom
Zoom: Full Size
bizhub C652/C652DS/C552/C552DS/C452
7-44
7.7
7.7
Printer Settings
7
Printer Settings
This setting is for the print operations. For details, refer to the "User's Guide [Print Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-45
7.8
7.8
Fax Settings
7
Fax Settings
This setting is for the fax and network fax operations. For details, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-46
7.9
7.9
System Connection
7
System Connection
Configure settings for software, cellular phone, or PDA that can be accessed with this machine.
%
[Utility/Counter] ö [Administrator Settings] ö [System Connection]
Settings
OpenAPI Settings
Access Setting
Specify whether to allow the user to access this
machine from other system that is using OpenAPI.
SSL/Port Settings
SSL Setting
To use SSL encryption,
select [SSL Only] or
[SSL/Non-SSL].
• If Enhanced Security Mode is enabled,
[SSL Only] is enabled.
Port No.
Enter a port number.
Port No. (SSL)
Enter the port number
to be used for SSL
communication.
Client Certificate Request
Specify whether to enable a client certificate
request. If you authenticate the client by requesting for its
certificate (verification
of client certificate), select [Enable].
Certificate Verification
Level Settings
To verify a certificate,
configure settings to
verify the certificate.
[Validity Period]:
Select whether to
check that the target
certificate is within the
validity period.
[Key Usage]:
Select whether to
check that the certificate key is being used
properly.[Chain]: Select whether to check
that the certificate
chain (certification
path) is correct.
[Expiration Date Confirmation]:
Select whether to
check the target certificate for validation.
[CN]:
Select whether to
check that the CN of
the certificate matches
the server address.
Authentication
Automatic Prefix/Suffix
Setting
Specify whether to authenticate an access from
other system that is using OpenAPI.
• To authenticate, enter the login name and
password in [Login Name] and [Password]
• When user authentication is performed or when
acquiring the device information with the PageScope Authentication Manager, set the Authentication setting of the OpenAPI Setting
screen of the machine to [OFF].
Select whether to automatically add prefix and suffix to a destination number.
If [Automatic Prefix/Suffix Setting] is set to [ON], the other settings will be restricted. For details, refer to the "User's Guide [Network Administrator]".
bizhub C652/C652DS/C552/C552DS/C452
7-47
7.9
System Connection
7
Settings
Printer Information
Specify [Printer Name], [Printer Location], [Printer Information], and [Printer
URI].
The [Printer Information] setting is linked to [Printer Information] in [HTTP Server Settings].
Cellular Phone/PDA
Setting
Specify whether to allow the user to print data in a cellular phone or PDA or
save such data in a User Box.
Factory default
Access Setting
Possible to combine
SSL Setting
Non-SSL Only
Client Certificates
Disable
Validity Period
Confirm
Key Usage
Do Not Confirm
Chain
Do Not Confirm
Expiration Date Confirmation
Do Not Confirm
CN
Do Not Confirm
Authenticate
OFF
Automatic Prefix/Suffix
Setting
OFF
Cellular Phone/PDA Setting
Restrict
bizhub C652/C652DS/C552/C552DS/C452
7-48
7.10
7.10
Security Settings
7
Security Settings
Configure the settings for the restricting the functions of this machine for processing secret data.
7.10.1
Administrator Password
Change the administrator password.
0
0
0
The administrator password can be entered using 0 through 8 digits.
If password rules are specified, an 8-digit password must be entered.
If you enter an incorrect administrator password a configured number of times, you are prohibited from
using this machine. In this case, contact your service representative.
1
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Administrator
Password].
Factory default
Administrator Password
12345678
2
Enter the administrator password, and then press [OK].
3
Enter a new administrator password.
4
Press [Password Confirmation], enter the administrator password again, and then press [OK].
5
Press [OK].
The password is changed.
d Reference
To configure password rule settings:
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Security Details] ö
[Password Rules].
7.10.2
User Box Administrator Setting
Configure settings for the User Box operations. For details, refer to the "User's Guide [Box Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-49
7.10
7.10.3
Security Settings
7
Administrator Security Levels
Configure settings so that the user can change some of the settings accessible only to the administrator.
Settings allowed to the user appear in User Settings.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Administrator
Security Levels].
Settings
Level 1
Allows the user to change the following settings.
• Power Save Settings
• Auto Zoom (Platen)
• Auto Zoom (ADF)
• Specify Default Tray when APS Off
• Select Tray for Insert Sheet
• Automatic Image Rotation
• Card Shot Settings
Level 2
Allows the user to change the following settings.
• All settings allowed in Level 1
• Output Settings
• AE Level Adjustment
• Blank Page Print Settings
• Change E-Mail Address
• Print Jobs During Copy Operation
Prohibit
Does not allow the user to change the settings allowed in Level 1 and Level
2.
Factory default
Administrator Security Levels
bizhub C652/C652DS/C552/C552DS/C452
Prohibit
7-50
7.10
7.10.4
Security Settings
7
Security Details
Configure security detail settings to restrict the functions of this machine. You can restrict the functions to
enhance security.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Security Details].
Settings
Password Rules
Configure whether to enable the password rules.
When enabled, the restrictions are applied to the following passwords. The
set passwords must be changed to ones that meet the conditions.
• Administrator password
• User password
• Account password
• User Box password
• Security document password
<Conditions of the password rules>
• Specify a password in 8 or more digits.
• Uppercase and lowercase letters are differentiated.
• Only half-width symbols can be used. For some of the passwords,
specification of """, "+", and "space" is restricted.
• A password that consists of a repetition of the same character cannot
be specified.
• The same password as one before being changed cannot be registered.
Prohibited Functions When
Authentication Error
bizhub C652/C652DS/C552/C552DS/C452
Configure restrictions on operation when you enter one of the following
passwords incorrectly.
• User password
• Account password
• User Box password
• Security document password
• Administrator password
Mode 1
Disables operations for a specified time if authentication fails.
Mode 2
Disables operations of the control panel if authentication fails.
Specify the max. allowance for authentication operation frequency.
Release
Releases the prohibited operations due to failure
in authentication, enabling the operations.
Release Time Settings
Configure the length of time until prohibited operations are automatically released.
7-51
7.10
Security Settings
7
Settings
Confidential Document Access Method
Synchronizes with the settings for "Prohibited Functions When Authentication Error", automatically changes it.
• Mode 1
Requires entering security document ID and password before selecting
a security document from a User Box.
• Mode 2
Performs authentication based on the password after you enter the security document ID and select a security document from a User Box.
Manual Destination Input
This setting is for the network scan, fax, and network fax operations. For
details, refer to the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Print Data Capture
This setting is for the print operations. For details, refer to the "User's
Guide [Print Operations]".
Job Log Settings
Configure job log settings to be obtained when power is turned off and on.
Specify the type of obtain log and whether to permit overwriting.
Pressing [Erase Job Log] erases the job log.
Restrict Fax TX
This setting is for the fax and network fax operations. For details, refer to
the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Hide Personal Information
Hide Personal Information
(MIB)
Specify whether to display the file name, address, or User Box number as
MIB information in Job List.
Display Activity Log
This setting is for the fax and network fax operations. For details, refer to
the "User's Guide [Network Scan/Fax/Network Fax Operations]".
Initialize
Initializes Job History, Network Settings, Copy Program, or Store Address.
Job History Thumbnail Display
Configure whether to perform thumbnail display when displaying the job
history.
Secure Print Only
This setting is for the print operations. For details, refer to the "User's
Guide [Print Operations]".
Copy Guard
Specify whether to use the Copy Guard function.
If [Copy Guard] is selected in [Application], you can embed copy inhibit information on paper. You can also detect copy inhibit information embedded on paper.
• Displayed when the optional Security Kit is installed.
Password Copy
Specify whether to use the Password Copy function.
If [Password Copy] is selected in [Application], you can embed a password
on paper. You can also detect a password embedded on paper.
• Displayed when the optional Security Kit is installed.
Factory default
Password Rules
Invalid
Prohibited Functions When
Authentication Error
•
•
Confidential Document Access Method
Mode 1
Manual Destination Input
Allow All
Print Data Capture
Allow
Job Log Settings
No
Restrict Fax TX
OFF
Hide Personal Information
OFF
Hide Personal Information
(MIB)
ON
Display Activity Log
ON
Job History Thumbnail Display
OFF
Secure Print Only
No
bizhub C652/C652DS/C552/C552DS/C452
Mode 1
Release Time Settings: 5 min.
7-52
7.10
Security Settings
7
Factory default
Copy Guard
No
Password Copy
No
bizhub C652/C652DS/C552/C552DS/C452
7-53
7.10
7.10.5
Security Settings
7
Enhanced Security Mode
The enhanced security mode cannot be enabled when any of the current functional settings conflict with the
enhanced security mode.
When the enhanced security mode is enabled, the settings required for the mode or the settings that have
been forcibly switched when entering the mode cannot be changed.
Required settings
To enable the enhanced security mode, the following settings must have been configured.
Administrator Settings
Required settings
User Authentication/Account Track / General Settings / User Authentication
Select either [ON (External Server)] or [ON (MFP)].
• When you enable account track, select [Account Name & Password] for the account track
input method.
Security Settings / Administrator Password
Set a password complying with password rules.
Security Settings / HDD Settings / HDD Lock Password
Set an HDD lock password.
[Security] in PageScope Web Connection / PKI
Settings / SSL Setting
•
•
• Image controller setting
• Management function setting
• CE password
• CE authentication function
• HDD installation setting
All the settings above must be configured by your
service representative.
Set [Mode using SSL/TLS] to [Administrator
mode] and [User mode].
Set [Encryption Strength] to [AES-256] or
[3DES-168].
These items must be configured by your service
representative. For details, contact your service
representative.
Settings to forcibly changed
When the enhanced security is enabled, the following settings are forced.
The changed settings will not revert when the enhanced security mode is turned off.
After the password rules have been changed, any passwords that do not comply with the changed rules
will not be authenticated. For details on the password rules, refer to page 7-51.
For details on the network settings to be forcibly changed, refer to the "User's Guide [Network
Scan/Fax/Network Fax Operations]".
Administrator Settings
Settings to forcibly changed
System Settings / Restrict User Access / Restrict
Access to Job Settings / Registering and Changing
Addresses
Set to [Restrict].
User Authentication/Account Track / General Settings / Pubic User Access
Set to [Restrict].
User Authentication/Account Track / User Authentication Settings / Administrative Settings / User
Name List
Set to [OFF].
User Authentication/Account Track / Print without
Authentication
Set to [Restrict].
Network Settings / FTP Setting / [FTP Server Settings]
[FTP Server Settings] is not displayed.
Network Settings / SNMP Setting / SNMP v1/v2c
Settings
[Write Setting] is set to [Disable].
Network Settings / SNMP Setting / SNMP v3 Settings
In [Write User], [Security Level] cannot be set to
[OFF].
Network Settings / TCPSocket Settings
[Use SSL/TLS] is set to [ON].
Network Settings / WebDAV Settings / WebDAV
Server Settings / SSL Settings
Set to [SSL Only].
bizhub C652/C652DS/C552/C552DS/C452
7-54
7.10
Security Settings
7
Administrator Settings
Settings to forcibly changed
System Connection / OpenAPI Setting
Set to [SSL Only].
Security Settings / User Box Administrator Setting
Set to [Restrict].
Security Settings / Security Details / Password
Rules
Set to [Enable].
Security Settings / Security Details / Prohibited
Functions When Authentication Error
Set to [Mode 2], and the number of tries is set to 3.
• The number of tries can be changed to 1, 2, or
3.
Security Settings / Security Details / Prohibited
Functions When Authentication Error / Release
Time Settings
The allowable setting range is limited to 5 or more
minutes. This value cannot be less than 5 minutes.
Security Settings / Security Details / Confidential
Document Access Method
Set to [Mode 2].
Security Settings/Security Details/Print Data Capture
Set to [Restrict].
Security Settings/Security Details/Hide Personal
Information (MIB)
Set to [ON].
Security Settings / Security Details / Initialize / Network Settings
[Network Settings] is not displayed.
Security Settings/Security Details/Job History
Thumbnail Display
Set to [OFF].
Security Settings / Image Log TX Setting
Set to [OFF].
Review Secure Print User Box
Only the list is displayed before the password authentication is performed.
[Network] in PageScope Web Connection / E-Mail
Setting / S/MIME
[Automatically Obtain Certificates] is set to [No].
[E-Mail Text Encryption Method] is set to [3DES].
[Maintenance] in PageScope Web Connection /
Reset / Network Setting Clear
[Network Setting Clear] is not displayed.
[Security Administrator] in PageScope Web Connection / Password Setting
[Administrator Password Setting] is not displayed.
CS Remote Care
Restricts the device setting in the remote mode
based on CS Remote Care.
If [Enhanced Security settings] is enabled, various security functions are configured to allow you to ensure
the higher-level security of data management. For details, contact your service representative. To enable the
enhanced security mode, the following settings must first be configured. Different screens appear depending
on the current settings.
7.10.6
HDD Settings
This setting is for the hard disk operations. For details, refer to the "User's Guide [Box Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-55
7.10
7.10.7
Security Settings
7
Function Management Settings
Configure the settings for the network functions that are difficult to count.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Function
Management Settings] .
Settings
Network Function Usage
Settings
ON
Configure the settings for the network management that are difficult to count when managing
operations.
OFF
The following functions cannot be used if "Network Function Usage Settings" is set to "OFF".
• PC-FAX transmission
• Using the HDD TWAIN driver to view and retrieve documents in User Boxes
• Using PageScope Box Operator to view and
retrieve documents in User Boxes
• Using PageScope Scan Direct to retrieve documents in User Boxes
• Box operations using PageScope Web Connection (The User Box tab does not appear.)
Factory default
Network Function Usage
Settings
bizhub C652/C652DS/C552/C552DS/C452
ON
7-56
7.10
7.10.8
Security Settings
7
Stamp Settings
Manage the stamp.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [Security Settings] ö [Stamp Settings].
Settings
Stamp Settings
Apply Stamps
Configure whether to add a stamp when printing
or sending.
To add a stamp, configure stamp contents settings.
d Reference
If a stamp is added, print settings cannot be configured in "Stamp/Composition" of "Application".
Delete Registered
Stamp
•
•
Stamp
Deletes all registered stamps.
Copy Protect/Stamp Repeat
Deletes all stamps registered in Copy Protect
and the stamp repeat function.
Factory default
Apply Stamps
Printing: Do Not Apply
Sending: Do Not Apply
d Reference
To configure copy protect and stamp repeat settings:
Press [Application] ö [Stamp/Composition].
7.10.9
Driver Password Encryption Setting
This setting is for the print operations. For details, refer to the "User's Guide [Print Operations]".
bizhub C652/C652DS/C552/C552DS/C452
7-57
7.11
7.11
License Settings
7
License Settings
Enable the functions of an optional component i-Option LK-101, LK-102, LK-103 or LK-105. For details on
the enabling procedure, refer to the "Quick Guide [Copy/Print/Fax/Scan/Box Operations]".
0
An optional component i-Option LK-101, LK-102, LK-103 or LK-105 must be purchased. For details,
contact your service representative.
%
Press the [Utility/Counter] key ö [Administrator Settings] ö [License Settings] .
Settings
Get Request Code
Issue a request code for this machine to be registered in the license management server (LMS).
Install License
Enter the function code and license code obtained from the license management server (LMS).
Reference
When the functions of an optional component i-Option LK-101, LK-102, LK-103 or LK-105 are enabled,
the enabled functions can be checked with [List of Enabled Functions].
bizhub C652/C652DS/C552/C552DS/C452
7-58
7.12
7.12
OpenAPI Authentication Management Settings
7
OpenAPI Authentication Management Settings
Configure settings to prevent our deprecated OpenAPI connection application from being registered in this
machine. For details, contact your service representative.
bizhub C652/C652DS/C552/C552DS/C452
7-59
8
Maintenance
8.1
Paper
8
Maintenance
8.1
Paper
8.1.1
Checking the paper
8
Replenishment message
If a tray has run out of paper during printing, load paper or change the paper tray. Load paper in the paper
tray that is highlighted in color.
Precautions regarding the use of paper
Do not use the following types of paper. Not observing these precautions may lead to reduced print quality,
a paper jam or a damage to the machine.
OHP transparencies that have already been fed through the machine (even if they are still blank)
Paper that has been printed on with a heat-transfer printer or an inkjet printer
Folded, curled, wrinkled, or torn paper
Paper that has been left unwrapped for a long period of time
Damp paper, perforated paper, or paper with punched holes
Extremely smooth or extremely rough paper, or paper with an uneven surface
Paper that has been treated, such as carbon-backed, heat-sensitive or pressure-sensitive paper
Paper that has been decorated with foil or embossing
Paper of a non-standard shape (paper that is not rectangular)
Paper that is bound with glue, staples or paper clips
Paper with labels attached
Paper with ribbons, hooks, buttons, etc., attached
Paper storage
Store paper in a cool, dark location with little humidity. If the paper becomes damp, a paper jam may occur.
Store the paper flat, not on its edge. Curled paper may cause a paper jam.
bizhub C652/C652DS/C552/C552DS/C452
8-2
8.1
8.1.2
Paper
8
Loading paper
This section describes how to load paper into each tray.
If printing stops due to the tray being empty, load paper into the tray. Printing restarts automatically.
For the types of paper to be used, refer to page 12-2.
Loading paper into trays 1 and 2
The same procedures can be used to load paper into trays 1 and 2.
The following procedure describes how to load paper into tray 1.
0
When "Auto Detect" is selected on the "Paper" tab, the size of loaded paper is automatically detected.
1
Pull out tray 1.
NOTICE
Be careful not to touch the film.
2
Film
Slide the lateral guides to fit the size of paper being loaded.
% If the lateral guides are not positioned correctly for the loaded
paper, the paper size will not be correctly detected.
3
Load the paper into the tray so that the side of the paper to be
printed on (the side facing up when the package was unwrapped)
faces up.
% Do not load so many sheets of paper that the top of the stack
is higher than the mark.
% If paper is curled, flatten it before loading it.
% If special paper is loaded, the paper type must be specified.
% Load letterhead paper so that the side to be printed on faces
down.
4
Close tray 1.
d Reference
To configure paper settings:
Press [Basic] ö [Paper].
bizhub C652/C652DS/C552/C552DS/C452
8-3
8.1
Paper
8
Loading paper into trays 3 and 4
The same procedures can be used to load paper into trays 3 and 4.
The following procedure describes how to load paper into tray 3.
1
Pull out tray 3.
NOTICE
Be careful not to touch the surface of the paper take-up roller with
your hand.
2
Lift up the paper take-up roller, and then load the paper into the
tray.
% Load the paper into the tray so that the side of the paper to be
printed on (the side facing up when the package was
unwrapped) faces up.
% Do not load so many sheets of paper that the top of the stack
is higher than the mark.
% Do not load tray 3 with paper of a size other than that
previously specified.
% If paper is curled, flatten it before loading it.
% If special paper is loaded, the paper type must be specified.
% Load letterhead paper so that the side to be printed on faces down.
% To change the paper size for tray 3, contact your service representative.
3
Lower the paper take-up roller, and then close tray 3.
d Reference
To configure paper settings:
Press [Basic] ö [Paper].
bizhub C652/C652DS/C552/C552DS/C452
8-4
8.1
Paper
8
Loading paper into the bypass tray
1
Open the bypass tray.
% To load large-sized paper, pull out the tray extension.
NOTICE
Be careful not to touch the surface of the paper take-up roller with
your hand.
2
With the side to be printed on facing down, insert the paper as far as possible into the feed slot.
% The image will be printed on the surface of the paper facing down when the paper is loaded into the
bypass tray.
% Do not load so many sheets of paper that the top of the stack is higher than the mark.
% If paper is curled, flatten it before loading it.
% Push the paper guides firmly up against the edges of the paper.
% Load letterhead paper so that the side to be printed on faces up.
% When loading postcards:
Load them in the w orientation, as shown in the illustration.
To use postcards other than 4 e 6-size (A6-size), check the
size of postcards to be used, and then select the size on the
Custom Size screen before using them.
% When using envelopes:
Expel air from the envelopes, and then load them while holding
the folds of the envelopes.
Load them with the flap side up, as shown in the illustration.
The flap side of envelopes cannot be printed on.
bizhub C652/C652DS/C552/C552DS/C452
8-5
8.1
Paper
8
% To load label sheets:
Load them in the w orientation, as shown in the illustration.
A label sheet consists of the printing surface, sticking layer,
and pasteboard. Peel off the pasteboard, then you can stick
the label to other objects.
3
Slide the lateral guides to fit the size of paper being loaded.
4
Select the paper type.
% To use label sheets, select [Thick 1].
% OHP transparencies can be printed only in black. Before selecting OHP transparencies, select
[Black] in the Color tab.
% If you select [4 e 6 w (A6 Card w)], the paper type is automatically set to [Thick 3].
d Reference
To configure paper settings:
Press [Basic] ö [Paper].
bizhub C652/C652DS/C552/C552DS/C452
8-6
8.1
Paper
8
Loading paper into the LCT
The same procedures can be used to load paper into the Large capacity unit LU-301 and LU-204.
The following procedure describes how to load paper into Large capacity unit LU-301.
0
To change the paper size, contact your service representative.
1
Open the upper door.
NOTICE
Be careful not to touch the surface of the paper take-up roller with
your hand.
2
Lift up the paper take-up roller, and then load the paper into the
tray.
% Load the paper into the tray so that the side of the paper to be
printed on (the side facing up when the package was
unwrapped) faces down.
% Do not load so many sheets of paper that the top of the stack
is higher than the mark.
% Do not load the LCT with paper of a size other than that
previously specified.
% If paper is curled, flatten it before loading it.
% If special paper is loaded, the paper type must be specified.
% Load letterhead paper so that the side to be printed on faces
up.
d Reference
To configure paper settings:
Press [Basic] ö [Paper].
bizhub C652/C652DS/C552/C552DS/C452
8-7
8.2
Consumables
8.2
Consumables
8.2.1
Checking comsumables
8
Replacement message
When it is time to replace the Toner Cartridge or Imaging Unit, an advanced warning message appears at the
top of the screen.
For the replacement procedure, refer to the guidance or the [Quick Guide Copy/Print/Fax/Scan/Box
Operations].
For details on using the guidance, refer to the [Quick Guide Copy/Print/Fax/Scan/Box Operations].
When the message appears, make a preparation and replace the Toner Cartridge or Imaging Unit according
to the guidance contained in your maintenance agreement.
When it is almost time to replace the Toner Cartridge, an advanced warning message similar to the one
shown below appears.
When the message appears, prepare to replace the Toner Cartridge according to the guidance contained in
your maintenance agreement.
When it is time to replace the Toner Cartridge or Imaging Unit, an advanced warning message similar to the
one shown below appears. Replace them according to the guidance contained in your maintenance
agreement.
Do not replace any color other than the one indicated in the message in the touch panel.
For the Toner Cartridge, the machine stops operating after the message appears.
Toner Cartridge
bizhub C652/C652DS/C552/C552DS/C452
8-8
8.2
Consumables
8
Imaging Unit
Replacement by user
Replacement by service representative
NOTICE
Do not replace the Imaging Unit until a "Please replace following unit(s)." message appears.
If you continue to use the drum unit while an advanced warning message is displayed, the following
replacement message appears. Replace the drum unit according to the guidance contained in your
maintenance agreement.
Toner Cartridge
Imaging Unit
Replacement by user
Replacement by service representative
If a Toner Cartridge other than for black or the Imaging Unit is empty, printing can continue using black. Press
[Continue], and then select the job to be printed.
bizhub C652/C652DS/C552/C552DS/C452
8-9
8.2
Consumables
8
Checking consumables status
In the Check Consumable Life screen, you can check the status (usage level) of consumables.
1
Press the [Utility/Counter] key.
2
Press [Check Consumable Life].
% To print the list of usage levels, press [Print List], then [Start] or the [Start] key.
Viewing counters
In the Meter Count screen, you can check the total number of prints since counting started. In the Coverage
Rate screen, the consumed amount of toner can be viewed.
1
Press the [Utility/Counter] key.
2
Press [Meter Count] ö [Check Details].
% To print the counter list, press [Print List], select paper, and then press the [Start] key.
bizhub C652/C652DS/C552/C552DS/C452
8-10
8.2
Consumables
8
% To display the Coverage Rate screen, press [Coverage Rate].
Checking the total number of pages printed
Pressing Total Counter displays the total number of pages printed to
date.
Total Counter
bizhub C652/C652DS/C552/C552DS/C452
8-11
8.3
8.3
Cleaning procedure
8
Cleaning procedure
Slit glass (bizhub C652/C552/C452)
NOTICE
Do not touch the slit glass.
1
Open the ADF, and then remove the slit glass cleaner.
2
Wipe stains off the slit glass using the slit glass cleaner.
% Wipe off stains from the back side to the front side along the
guide.
Slit glass (front) (bizhub C652DS/C552DS)
NOTICE
Do not touch the slit glass (front).
1
Open the ADF, and then remove the slit glass cleaner.
2
Wipe stains off the slit glass using the slit glass (front) cleaner.
% Wipe off stains from the back side to the front side along the
guide.
bizhub C652/C652DS/C552/C552DS/C452
8-12
8.3
Cleaning procedure
8
Slit glass (back) (bizhub C652DS/C552DS)
NOTICE
Do not touch the slit glass (back).
1
Open the ADF, and then remove the slit glass cleaner.
2
Open the opening and closing guide.
3
Wipe stains off the slit glass using the slit glass (back) cleaner.
% Wipe off stains from the back side to the front side along the
guide.
Original glass, control panel, paper take-up roller
NOTICE
Do not press the control panel hard, or the keys and touch panel may be damaged.
%
Wipe the surface using a soft, dry cloth.
bizhub C652/C652DS/C552/C552DS/C452
8-13
8.3
Cleaning procedure
8
Housing, document pad
NOTICE
Never use solvents, such as benzene or thinner, to clean the document pad.
%
Wipe the surface using a soft cloth moistened with a mild household detergent.
bizhub C652/C652DS/C552/C552DS/C452
8-14
9
Troubleshooting
9.1
9
When the message "Trouble" appears (call a service representative)
9
Troubleshooting
This chapter describes troubleshooting.
9.1
When the message "Trouble" appears (call a service
representative)
If this message appears, perform the operation described in the message. If the problem is not resolved,
perform the following operations, and then contact your service representative.
Normally, the phone number and fax number of your service representative appear in the center of the
screen.
If a defective part can be separated in order to be able to continue operations after a problem has been
detected, [Continue] or [Recover Data] is displayed. To continue operations, select any key. However, the
problem has not been resolved, so contact your service representative immediately.
Problems that cannot be corrected by the user
1
Write down the malfunction code in the Service Call screen.
2
Turn off the [sub power switch].
3
Turn off the [main power switch].
bizhub C652/C652DS/C552/C552DS/C452
9-2
9.1
When the message "Trouble" appears (call a service representative)
4
Unplug the machine.
5
Contact your service representative and inform them of the written down malfunction code.
bizhub C652/C652DS/C552/C552DS/C452
9
9-3
9.2
9.2
Troubleshooting table
9
Troubleshooting table
Simple troubleshooting
The following explains simple troubleshooting procedures. If the problem is not corrected after the described
operation is performed, contact your service representative.
Description of problem
Check points
Remedy
The machine does not start up
when the [main power switch] is
turned on
Is power being supplied from the
electrical outlet?
Correctly insert the power supply
plug into the electrical outlet.
Has the [sub power switch] been
turned on?
Turn on the [sub power switch].
Is the upper right-side door of
the machine open?
Securely close the upper rightside door of the machine.
Is there any paper that matches
the original?
Load paper of the appropriate
size into the paper tray.
Is the copy density set to [Light]?
Press [Dark] in the Density
screen to copy at the desired
copy density. (p. 5-18)
Is the paper damp?
Replace with new paper. (p. 8-3)
Is the copy density set to [Dark]?
Press [Light] in the Density
screen to copy at the desired
copy density. (p. 5-18)
Was the original not pressed
close enough against the original
glass?
Position the original so that it is
pressed closely against the original glass. (p. 3-5)
Is the paper damp?
Replace with new paper. (p. 8-3)
Was the original not pressed
close enough against the original
glass?
Position the original so that it is
pressed closely against the original glass. (p. 3-5)
Is the original glass dirty?
Wipe the glass with a soft, dry
cloth. (p. 8-13)
Is the slit glass dirty?
Clean the slit glass with the slit
glass cleaner. (p. 8-12)
Is the document pad dirty?
Clean the document pad with a
soft cloth dampened with a mild
detergent. (p. 8-14)
Was the original printed on highly
translucent material, such as diazo photosensitive paper or OHP
transparencies?
Place a blank sheet of paper on
top of the original. (p. 3-5)
Is a 2-sided original being copied?
If a thin 2-sided original is being
copied, the print on the back side
may be reproduced on the front
side of the copy. In the Background Removal screen, select a
lighter background density.
(p. 5-18)
Is the electrostatic charger wire
dirty?
Use the charger-cleaning tool to
clean the electrostatic charger.
(p. 9-12)
Copying does not start
The printed output is too light
The printed output is too dark
The printed image is blurry
There are dark specks or spots
throughout the printed output
There are streaks in the printed
output
bizhub C652/C652DS/C552/C552DS/C452
9-4
9.2
Troubleshooting table
9
Description of problem
Check points
Remedy
The image is printed at an angle
Is the original positioned correctly?
Correctly position the original
against the document scales.
(p. 3-5)
Load the original into the ADF,
and slide the adjustable lateral
guides to fit the size of the original. (p. 3-4)
Is the original incorrectly positioned in the ADF?
If the original cannot be fed correctly through the ADF, make
copies by positioning the original
on the original glass. (p. 3-5)
Is the slit glass dirty (while using
the ADF)?
Clean the slit glass with the slit
glass cleaner. (p. 8-12)
Are the adjustable lateral guides
incorrectly positioned against
the edges of the paper?
Slide the adjustable lateral
guides against the edges of the
paper.
Was curled paper loaded into the
paper tray?
Flatten the paper before loading
it.
Was paper that curls easily (as
with recycled paper) used?
Remove the paper from the paper tray, turn it over, and then
load it again.
The printed page is curled
Replace with new dry paper.
(p. 8-3)
The edge of the printed image is
dirty
Is the document pad dirty?
Clean the document pad with a
soft cloth dampened with a mild
detergent. (p. 8-14)
Was the selected paper size larger than the original?
(With a Zoom setting of "Full
Size" (100.0%))
Select a paper size that is the
same size as the original.
Otherwise, select Auto to enlarge
the copy to the selected paper
size. (p. 5-7)
Is the size or orientation of the
original different from that of the
paper?
(With a Zoom setting of "Full
Size" (100.0%))
Select a paper size that is the
same size as the original. Otherwise, select a paper orientation
that is the same as that of the
original.
Was the copy reduced to a size
smaller than the paper (with a reduced zoom ratio specified)?
Select a zoom ratio that adjusts
the original size to the selected
paper size.
Otherwise, select Auto to enlarge
the copy to the selected paper
size. (p. 5-7)
Even though a paper jam was
cleared, copies cannot be produced
Is paper jammed at other locations?
Remove any jammed paper from
other locations.
Printing with the "2-Sided >
1-Sided" or "2-Sided > 2-Sided"
settings are not available
Have settings been selected that
cannot be combined?
Check the combinations of the
selected settings.
Copying is not possible even
though the password is entered
on a machine with account track
settings configured
Did the message "Your account
has reached its maximum allowance." appear?
Contact your administrator.
The original is not fed
Is the ADF slightly open?
Securely close the ADF.
Is the original one that does not
meet the specifications?
Check that the original is one
that can be loaded into the ADF.
(p. 12-7)
Is the original correctly loaded?
Position the original correctly.
(p. 3-4)
Is any power being supplied to
the connector?
Check that the cord is correctly
inserted into the connector.
The Finisher or Job Separator
JS-504 does not run.
bizhub C652/C652DS/C552/C552DS/C452
9-5
9.2
Troubleshooting table
9
Description of problem
Check points
Remedy
The staple is incorrectly positioned by 90°
Has the staple position been correctly specified?
Specify the desired position for
stapling. (p. 5-10)
The pages that were fed out
were not uniformly loaded and
the punched holes or staples
are incorrectly positioned
Is the paper curled?
Remove the paper from the paper tray, turn it over, and then
load it again.
Is there a gap between the lateral
guides in the paper tray and the
sides of the paper?
Slide the lateral guides in the paper tray against the sides of the
paper so that there is no gap.
Is the paper type configured correctly?
Configure the paper type of the
selected tray correctly.
Though the authentication unit
is connected with this machine
sing a USB cable, the status indicator LED does not light in
green
A malfunction of the USB port of
this machine is suspected.
Turn off the main power of this
machine, disconnect the USB
cable from this machine or authentication unit, and then connect it again. Wait at least 10
seconds, and then turn on the
main power of this machine.
Though the authentication unit
is connected with the computer
using a USB cable, the status indicator LED does not light in
green
MA malfunction of the USB port
of your computer is suspected.
Restart your computer.
Has the authentication unit driver
being installed correctly?
Check that your computer is installed to the computer correctly.
(p. 10-2) (p. 11-2)
No notice sound is given when
scanning is started or authentication is finished on this machine
Has the notice sound being set
to OFF on this machine?
Set the notice sound to ON.
(p. 10-2)
When the "Failed to register"
message appears on this machine where registration fails
The scanning time on the authentication unit is limited per
scanning. If scanning does not
finish within the limited time, the
corresponding message appears.
For details on the scanning time,
contact your service representative.
To finish scanning within the limited time, confirm how to perform
authentication and how to place
your finger when scanning.
(p. 10-2)
During scanning, place the
scanned part on the scanning
section correctly, and do not
move it until results have been
obtained.
If the scanned part is dusty or
rough and dry when performing
authentication, a correct image
will not be able to be obtained,
and scanning may not finish.
Clean your finger, and then scan
it again, or improve the rough
and dry condition of your finger.
If the scanned part is too thick or
thin (when the finger width is outside the range from 3/8 to 1 inch
(10 to 25 mm)), a correct image
cannot be obtained, and scanning may not finish. Try "stretching your finger", "placing your
finger deeply", or "placing your
finger shallowly" on the scanning
section.
When the "Failed to authenticate." message appears on this
machine where login fails
When the "Failed to read data.
Place your finger once again
and click the [Start reading] button." message appears on the
computer where registration has
failed
bizhub C652/C652DS/C552/C552DS/C452
The scanning time on the authentication unit is limited to five
seconds per scan. If scanning
does not finish within five seconds, the corresponding message appears.
9-6
9.2
Troubleshooting table
9
Description of problem
Check points
Remedy
Scanning does not start
Have you placed your finger correctly on the authentication unit?
Confirm how to perform authentication and how to place your
finger when scanning. (p. 10-2)
During scanning, place the
scanned part on the scanning
section correctly, and do not
move it until results have been
obtained.
If the scanned part is dusty or
rough and dry when performing
authentication, a correct image
will not be able to be obtained,
and scanning may not finish.
Clean your finger, and then scan
it again, or improve the rough
and dry condition of your finger.
If the scanned part is too thick or
thin (when the finger width is outside the range from 3/8 to 1 inch
(10 to 25 mm)), a correct image
cannot be obtained, and scanning may not finish. Try "stretching your finger", "placing your
finger deeply", or "placing your
finger shallowly" on the scanning
section.
Did you restart this machine after
connecting the authentication
unit to this machine?
Turn off the main power of this
machine, disconnect the USB
cable from this machine or authentication unit, and then connect it again. Wait at least 10
seconds, and then turn on the
main power of this machine.
Connecting the authentication
unit to the computer starts the
hardware uninstall wizard
Is the USB port to which the authentication unit is connected the
same as the one used when installing the driver?
If you connect the authentication
unit to a different USB port from
the one used when installing the
driver, the hardware uninstall
wizard may start. Use the same
USB port as the one used when
installing the driver.
When the "Failed to register"
message appears on this machine where registration fails
The scanning time of the authentication unit is limited to 10 seconds. If scanning does not finish
within the limited time, the corresponding message appears.
To finish scanning within the limited time, confirm how to place
the IC card. (p. 11-2)
When the "Failed to authenticate." message appears on this
machine where login fails
When IC card authentication +
password authentication is enabled
Did you enter the correct password?
Check the password, and then
enter the correct one if not.
Scanning does not start
Did you restart this machine after
connecting the authentication
unit to this machine?
Turn off the main power of this
machine, disconnect the USB
cable from this machine or authentication unit, and then connect it again. Wait at least 10
seconds, and then turn on the
main power of this machine.
When a message appears on
the computer where registration
fails
bizhub C652/C652DS/C552/C552DS/C452
9-7
9.2
Troubleshooting table
9
Main messages and their remedies
If any message other than those listed below appears, perform the operation described in the message.
Message
Cause
Remedy
Originals left on original glass.
The original has been left on the
original glass.
Remove the original from the
original glass.
Paper of matching size is not
available.
Select the paper size.
Paper of a suitable size is not
loaded in a paper tray.
Either select paper of a different
size or load paper of a suitable
size.
Place paper in Bypass Tray.
Paper of a suitable size is not
loaded in the bypass tray.
Load paper of the appropriate
size into the bypass tray.
The original size cannot be detected
Select the paper size.
(1) The original is not positioned
correctly.
(2) An original with a nonstandard
size or with a size too small to be
detected is loaded.
(1) Position the original correctly.
(2) Select the correct paper size.
The image will not fit in the selected paper size.
Change the direction of the original
The image does not fit in the paper.
Turn the original 90° and load it.
Cannot be set with XXX.
Functions that cannot be used
together are selected.
Make copies using only one of
the functions.
The output tray has reached its
capacity.
Remove paper from the tray indicated by
.
Copy cannot be performed because the paper loading capacity
of the output tray of the displayed Finisher or Job Separator
reached the maximum.
Remove all paper from the indicated tray.
Enter the login user name and
password and then touch
[Login] or press the [Access]
key.
User authentication settings
have been configured. Copies
cannot be made unless a user
name and correct password are
entered.
Enter the correct user name and
password. (p. 4-8)
Enter Account Name and password, and then touch [Login] or
press the [Access] key.
Account track settings have
been configured. Copies cannot
be made unless an account
name and correct password are
entered.
Enter the correct account name
and password. (p. 4-8)
Your account has reached its
maximum allowance.
The limit on the number of pages
that can be printed has been
reached.
Contact the administrator of the
machine.
The part indicated by
is
open.
Ensure that it is properly closed.
Since a machine door or cover is
open or an option is not installed
correctly, the machine is unable
to make copies.
Make sure that all doors and
covers of this machine and options are closed securely.
Check covers.
The exit cover of the finisher is
open.
Securely close the exit cover of
the finisher.
Install the Imaging Unit and
close all doors
The indicated Imaging Unit is not
installed correctly.
Reinstall each consumable and
replaceable part. Or contact your
service representative.
[Install a toner cartridge.]
The indicated toner cartridge is
not installed correctly.
Reinstall each consumable and
replaceable part. Or contact your
service representative.
[Set the toner cartridge, and
close all doors.]
The indicated toner cartridge is
not installed correctly.
Reinstall each consumable and
replaceable part. Or contact your
service representative.
Install the waste toner box and
close all doors.
The waste toner box is not installed correctly.
Reinstall each consumable and
replaceable part. Or contact your
service representative.
Incorrect Imaging Unit is installed. Install the correct Imaging Unit and close all doors.
The correct Imaging Unit is not
set.
Reinstall each consumable and
replaceable part. Or contact your
service representative.
bizhub C652/C652DS/C552/C552DS/C452
9-8
9.2
Troubleshooting table
9
Message
Cause
Remedy
Replenish paper.
The indicated tray has run out of
paper.
Add paper. (p. 8-3)
Toner (X) is low. Please when indicate.
The toner for the indicated color
is about to run out.
Prepare to replace the toner cartridge following the guidance
contained in your maintenance
agreement.
Install toner cartridge (X)
The toner is about to run out.
Replace the toner cartridge following the guidance contained in
your maintenance agreement.
Toner is depleted
Replace the toner cartridge following the guidance (explanation).
Press the [Continue] button to
continue the operations.
Toner is depleted
Replace the toner cartridge following the guidance contained in
your maintenance agreement.
No more staples.
Replace the staple cartridge, or
cancel stapling
The staples have run out.
Replace the staple cartridge.
Misfeed detected. Remove paper according to the instructions.
Since a paper jam occurred, the
machine is unable to make copies.
Clear the jammed paper.
Empty hole-punch scrap box
To continue the job, disable
punching.
(1) The punch scrap box is full.
(2) The punch scrap box is not installed.
(1) Throw punch scraps away
from the punch scrap box.
(2) Install the punch scrap box.
Reset the following number of
originals.
XX
After clearing a paper jam, it is
necessary to reload certain pages of the original that have already been fed through the ADF.
Load the indicated original pages
into the ADF.
An internal error occurred. Open
and then close the front door. If
the trouble code appears again,
contact your Service Rep.
The machine malfunctioned and
is unable to make copies.
Take a remedy according to the
message displayed in the
screen. If the problem is not resolved or released, inform your
service representative of the
malfunction code displayed in
the screen.
Malfunction detected.
Inform the service representative of the error code.
The machine malfunctioned and
is unable to make copies.
Inform your service representative of the code displayed in the
screen.
Clean the slit scan glass on the
far left with a glass cleaner.
Continuing using the machine in
this condition may cause lines to
appear in the output.
The slit glass is dirty.
User the slit glass cleaner to
clean it.
Clean the slit glass on the left
side of the machine with the
glass cleaner. Continuing using
the machine in this condition
may cause lines to appear in the
output.
The slit glass (front) is dirty.
User the slit glass cleaner to
clean it.
Clean the slit glass on the left
side of the ADF with the glass
cleaner. Continuing using the
machine in this condition may
cause lines to appear in the output.
The slit glass (back) is dirty.
User the slit glass cleaner to
clean it.
An internal error occurred. Turn
the main switch OFF and ON. If
the trouble code appears again,
contact your Service Rep.
bizhub C652/C652DS/C552/C552DS/C452
9-9
9.2
Troubleshooting table
9
Message
Cause
Remedy
Now Downloading Program
Data from the Firmware server.
(1) CS Remote Care was activated by your service representative.
(2) Internet ISW is being downloaded.
Do not turn off the sub power
switch while this message is displayed.
After turning off the sub power
switch, turn off the main power
switch, and then contact your
service representative.
Authentication information entered is invalid, due to failed access attempts.
Contact the administrator.
The authentication information
has become invalid since the authentication attempts have failed
the specified number of times.
Contact the administrator of the
machine.
Due to failed access attempts,
the current administrator password is invalid.
The administrator password has
become invalid since the authentication attempts have failed the
specified number of times.
Turn the machine off, then on
again.
Turn off the main power switch,
and then wait at least 10 seconds before turning it on again.
The job log has reached the
maximum allowed.
Contact the administrator.
The write area of the job log has
reached the maximum allowed.
Obtain the job log using PageScope Web Connection.
No Animation Guide data available. Contact your administrator.
Animation guide data is not installed.
For details on installing animation guide data, contact your
service representative.
Verify that external keyboard is
properly connected. It may not
be connected or multiple keyboards may be connected.
The compact keyboard is not
connected to this machine.
Turn off the main power of this
machine, connect the compact
keyboard to this machine. Wait
at least 10 seconds, and then
turn on the main power of this
machine.
Icons that appear in the touch-panel screen
Icon
Description
Indicates that data is being sent from the machine, regardless of the current mode.
Indicates that the machine is receiving data, regardless of the current
mode.
Indicates that an error occurred during an image stabilization operation, a
print operation or a scan operation.
Press this icon to view a screen containing a warning code.
If the warning screen was closed when a warning occurred, press this button to display the warning screen again.
Appears when there is a message indicating that consumables must be replaced or the machine requires maintenance. Press this button to display
the message, and then carry out the replacement or maintenance procedure.
Appears when an error occurs with the connection to the POP server.
Indicates that paper is not loaded in the paper tray.
Indicates that very little paper remains in the paper tray.
If the optional image controller is installed, press this icon to display the
setting screen for the image controller.
bizhub C652/C652DS/C552/C552DS/C452
9-10
9.2
Troubleshooting table
Icon
9
Description
Indicates that "Enhanced Security Mode" is set to "ON".
Appears when the external memory (USB memory) is not connected.
Indicates that a nonstandard external memory has been connected to this
machine, therefore, USB connection is not enabled.
Indicates that the job is in the waiting-for-redial status because, for example, the recipient's line is busy when sending with the G3 Fax or IP Address
Fax function.
bizhub C652/C652DS/C552/C552DS/C452
9-11
9.3
9.3
If print quality is deteriorated
9
If print quality is deteriorated
Cleaning the electrostatic charger wire
If the electrostatic charger wire is dirty, streaks will appear though the printed images. If this occurs, follow
the procedure described below to clean the electrostatic charger wire.
0
When replacing the waste toner box, follow the "Quick Guide" to clean the electrostatic charger wire.
1
Open the machine's lower front door.
2
Slowly pull out the charger-cleaning tool as far as possible. Next,
slowly push in the charger-cleaning tool as far as possible.
Repeat the above operations three times.
3
Securely insert the charger-cleaning tool, and then close the front door.
bizhub C652/C652DS/C552/C552DS/C452
9-12
9.3
If print quality is deteriorated
9
Cleaning the print head
If the print head becomes dirty, print quality may be reduced. If this occurs, clean the print head according
to the following procedure.
1
Pull out tray 1.
2
Remove the print head glass cleaning tool from tray 1.
3
Open the machine's lower front door.
4
Release the securing levers for the waste toner box, and then
remove the waste toner box.
bizhub C652/C652DS/C552/C552DS/C452
9-13
9.3
If print quality is deteriorated
5
Insert the print head glass cleaning tool into the print head
cleaning opening, pull it out, and then repeat this back-and-forth
movement two or three times.
6
Install the waste toner box.
7
Place back the print head glass cleaning tool to tray 1.
8
Close tray 1.
bizhub C652/C652DS/C552/C552DS/C452
9
9-14
10
Authentication unit (biometric
type)
10.1
10
Using an authentication unit (biometric type)
10
Authentication unit (biometric type)
This chapter describes the authentication unit (biometric type).
2
1
1.
2.
10.1
Authentication unit (biometric type) AU-101
Authentication unit (biometric type) AU-102
Using an authentication unit (biometric type)
The authentication unit (biometric type) is a "biometrics (biometric authentication)" system that scans a finger
vein pattern to perform personal authentication. Using the biometric authentication, you can log in to this
machine where user authentication settings are configured in order to execute a print job.
Place your forefinger straight so that your forefinger cushion slightly touches the hollow and protuberance
part of the scanning section. Secure your middle finger and thumb on the both sides of the authentication
unit to prevent your forefinger to be used for authentication from rotating.
For details on how to place your forefinger on the authentication unit, refer to page 10-17.
NOTICE
If you change the authentication unit from AU-101 to AU-102, the users you registered with AU-101 cannot
use AU-102. Connect AU-102 to this machine, and then register the users again.
Do not place anything other than your finger on the scanning section during scanning operation. Doing so
may cause a malfunction.
Do not disconnect the USB cable from the authentication unit or computer during a scanning operation.
Doing so may cause the system to become unstable.
The status indicator LED and notice sound indicate the status of the authentication unit.
Status indicator LEDs
Status
Lit in green
Ready state or authentication is completed
Flash in green
During authentication or scanning operation
Lit in red
Authentication failed or scanning failed
Unlit
The authentication unit is not recognized
Notice sound
Status
One short blip sound
Scanning starts
One short blip sound
One short blip
During a retry after authentication failed
sound*1/two
short blip
sounds*2
*1
Authentication completed
Two short blip sounds /
one short blip and one long beep sounds*2
Authentication failed
One long beep sound*2
Scanning canceled
*1For
authentication unit (biometric type) AU-101
*2For
authentication unit (biometric type) AU-102
bizhub C652/C652DS/C552/C552DS/C452
10-2
10.1
Using an authentication unit (biometric type)
10
To use the authentication unit, first register the finger vein pattern of the user in this machine. The registered
user, who is authenticated with the finger vein pattern, can log in to this machine or execute a print job. This
section explains how to configure the required settings in this machine, register users, and log in with
authentication.
10.1.1
Configuring this machine
NOTICE
User authentication settings must be configured with MFP authentication on this machine.
This device does not support external server authentication. To combine account track settings with user
authentication settings, set Synchronize User Authentication & Account Track to "Synchronize".
1
Use the control panel of this machine to display the Administrator Settings screen. Press [4 User
Authentication/Account Track], then [1 General Settings].
2
Set [User Authentication] to "ON (MFP)", and then press [OK].
3
Press [Yes], and then [OK].
4
Press [8 Authentication Device Settings].
5
Press [1 General Settings].
6
Press [Bio Authentication].
bizhub C652/C652DS/C552/C552DS/C452
10-3
10.1
Using an authentication unit (biometric type)
7
10
Configure "Beep Sound" and "Operation Settings".
% For "Beep Sound", specify whether to give a "blip" sound when the finger vein pattern is scanned
successfully.
% For "Operation Settings", specify how to log in to this machine after registration.
1-to-many authentication: Allows the user to log in by simply placing his or her finger.
1-to-1 authentication: Allows the user to log in by entering the user name and placing his or her
finger.
For details on how to log in to this machine, refer to page 10-17.
8
Press [OK] twice.
9
Press [2 Logoff Settings].
10
Specify whether to log out the user when scanning the original has finished after the user logged in with
the authentication unit.
11
Press [OK].
12
Press [Close] twice.
bizhub C652/C652DS/C552/C552DS/C452
10-4
10.1
10.1.2
Using an authentication unit (biometric type)
10
Registering a user
The following two methods can be used to register a user.
Connect the authentication unit to this machine, and directly register the target user in this machine
Connect the authentication unit to your computer, and use Data Administrator to register the target user
NOTICE
The registered user data is saved in the HDD of this machine. Changing the user authentication type of this
machine or formatting the HDD will erase the registered user data.
Registering a user using the control panel of this machine
1
Use the control panel of this machine to display the Administrator Settings screen. Press [4 User
Authentication/Account Track], and then [2 User Authentication Settings].
NOTICE
[2 User Authentication Settings] is disabled when User Authentication is set to [OFF] in General
Settings.
2
Press [2 User Registration].
3
Select a desired registration number, and then press [Edit].
4
Press [Register Auth. Info.].
bizhub C652/C652DS/C552/C552DS/C452
10-5
10.1
Using an authentication unit (biometric type)
5
Press [Edit].
6
Place your finger on the authentication unit to scan the finger vein pattern.
10
% Scan the finger vein pattern three times; reset the same finger each time and then press [Scan] for
each scanning.
% After scanning the finger vein pattern, place the same finger on the authentication unit, and press
[Authentication Test].
% If your finger vein patterns have been authenticated in the authentication test, press [New]. If
authentication has failed, retry scanning the finger.
7
Press [Close] twice.
8
Enter the user name and password.
9
Configure function permission settings as required.
10
Press [OK].
11
Press [Close].
Registering a user using Data Administrator
To use Data Administrator, configure this machine, and set up Data Administrator. For setup, install the
BioDriver (USB-Driver) of the authentication unit, and then install Data Administrator Bio Plugin.
NOTICE
Before setup, install Data Administrator V4.0 or later in your computer. For the Data Administrator operating
environment and installation procedure, refer to the Data Administrator User's Guide.
bizhub C652/C652DS/C552/C552DS/C452
10-6
10.1
Using an authentication unit (biometric type)
10
Checking the version of the installed Data Administrator
1
From the "Help" menu of Data Administrator, select "Version Information".
NOTICE
This software cannot be used if the version is "3.x". Install "4.x".
If Data Administrator V3.x is installed, it is removed when V4.x is installed.
2
Click the [Plug-in version].
3
In "Plug-in information list:", confirm the plugin version of Data Administrator.
% This software is available if the plugin version is "4.x".
Setup
1
Turn the main power of this machine off, and disconnect the authentication unit from this machine.
2
Install BioDriver (USB-Driver).
Connect the authentication unit to the USB port of your computer.
The "Found New Hardware" dialog box appears.
3
Select "Locate and install driver software (recommended)".
4
Insert the application CD-ROM provided with the authentication unit into the CD-ROM drive of the
computer.
bizhub C652/C652DS/C552/C552DS/C452
10-7
10.1
Using an authentication unit (biometric type)
5
Click the "Browse my computer for driver software (advanced)".
6
Check that the driver's search location is the application CD-ROM, and then click the [Next].
10
% When the driver's search location is not the application CD-ROM, click the [Browse]. Select the
BioDriver (USB-Driver) folder on the CD-ROM, and then click the [OK].
bizhub C652/C652DS/C552/C552DS/C452
10-8
10.1
Using an authentication unit (biometric type)
10
% Installation starts.
7
Click the [Close].
Installation of BioDriver (USB-Driver) is completed.
8
Install Data Administrator Bio Plugin.
Open the DA_Bio_Plugin folder on the application CD-ROM, and then click setup.exe.
9
Select a language, and then click the [OK].
The installation program starts.
10
Follow the on-screen instructions to proceed with the installation.
bizhub C652/C652DS/C552/C552DS/C452
10-9
10.1
Using an authentication unit (biometric type)
11
Click the [Next].
12
Select "I accept the terms in the license agreement", and then click the [Next].
13
Click the [Install].
bizhub C652/C652DS/C552/C552DS/C452
10
10-10
10.1
Using an authentication unit (biometric type)
14
10
Click the [Finish].
Installation of the Data Administrator Bio Plugin is completed, which completes the setup.
User registration
To register a user with Data Administrator, connect the authentication unit to the USB port of the computer,
and also connect the computer to this machine via network.
1
If the authentication unit is already connected to this machine, turn the main power switch of this
machine off, and then disconnect the authentication unit.
% When the authentication unit is already connected to the computer, go to step 4.
NOTICE
To turn the main power switch off and on, first turn the main power switch off, and then turn it on after
10 or more seconds has elapsed. Not doing so may result in an operation failure.
When connecting or disconnecting the USB cable, hold the plug. Otherwise, the cable may be
damaged.
2
Turn the main power on.
3
Connect the authentication unit to the USB port of the computer that contains Data Administrator.
NOTICE
Do not connect another USB device to the same port as for the authentication unit. Doing so reduces
the USB power supply, resulting in an operation failure.
To use the USB hub, be sure to connect the self-power USB hub that supplies 500 mA or more.
Restart the procedure 5 or more seconds after connecting the authentication unit.
bizhub C652/C652DS/C552/C552DS/C452
10-11
10.1
Using an authentication unit (biometric type)
4
10
Data Administrator starts, and device information of this machine is imported.
The Device Information window appears.
% For details on how to import device information, refer to the Data Administrator User's Guide.
5
In Select Function, select "Authentication Settings" - "User Setting", and then click the [Add].
bizhub C652/C652DS/C552/C552DS/C452
10-12
10.1
Using an authentication unit (biometric type)
6
10
Select the desired template, and then click the [OK].
The User Registration window appears.
7
Enter the user name and password, select the "AU-101" or "AU-102" tab, and then click the [Register
Auth. Info].
% Enter the E-mail address and other information as required.
bizhub C652/C652DS/C552/C552DS/C452
10-13
10.1
Using an authentication unit (biometric type)
8
10
Register finger vein pattern.
% Scan the finger vein patterns three times; reset the same finger and then press [Start Reading] for
each scanning.
% After scanning the finger vein patterns, place the same finger, and click [Authentication Test].
% If the authentication test has succeeded, press [Register].
% If the authentication test has failed, place your finger on the authentication unit again, and click
[Authentication Test].
% If the authentication has failed, click [Reset] to repeat the scanning process.
For authentication unit AU-101
For authentication unit AU-102
9
Click the [Registration].
bizhub C652/C652DS/C552/C552DS/C452
10-14
10.1
Using an authentication unit (biometric type)
10
10
Click the [OK].
% Repeat steps 5 to 10 to register all users.
11
Click the [Export to the device].
% Select the user name and click the [Edit] to change the registered data.
bizhub C652/C652DS/C552/C552DS/C452
10-15
10.1
Using an authentication unit (biometric type)
12
10
Click the [Write].
% Data Administrator provides the batch copy function that batch-configures the registered user data
in multiple machines with the authentication unit enabled.
The registered user data is configured in this machine.
13
Click the [OK].
14
Disconnect the authentication unit from the USB port of the computer.
15
Turn the main power switch of this machine off, connect the authentication unit to this machine, and
turn the main power of this machine on.
NOTICE
To turn the main power switch off and on, first turn the main power switch off, and then turn it on after
10 or more seconds has elapsed. Not doing so may result in an operation failure.
When connecting or disconnecting the USB cable, hold the plug. Otherwise, the cable may be
damaged.
bizhub C652/C652DS/C552/C552DS/C452
10-16
10.1
10.1.3
Using an authentication unit (biometric type)
10
Logging in to this machine
This section explains how to log in to this machine with the finger vein pattern authentication.
To use authentication unit (biometric type), register the finger vein pattern in advance.
If authentication fails frequently, finger vein pattern may not be registered correctly. Register the finger
vein pattern again.
Authentication is carried out when you simply place your finger on the 1-to-many authentication.
Authentication is carried out when you enter the user name and place your finger on the 1-to-1
authentication.
Press [ID & PW] to log in by entering the user name and the password, without using the authentication
unit.
When 1-to-many authentication has been specified
%
Place your finger on the authentication unit.
Authentication unit (biometric type) AU-101
Authentication unit (biometric type) AU-102
The basic settings screen appears.
bizhub C652/C652DS/C552/C552DS/C452
10-17
10.1
Using an authentication unit (biometric type)
10
When 1-to-1 authentication has been specified
1
Select [User Name], and enter the user name.
2
Place your finger on the authentication unit.
Authentication unit (biometric type) AU-101
Authentication unit (biometric type) AU-102
The basic settings screen appears.
bizhub C652/C652DS/C552/C552DS/C452
10-18
11
Authentication unit (IC card
type)
11.1
11
Using authentication unit (IC card type)
11
Authentication unit (IC card type)
This chapter describes the authentication unit (IC card type).
1
1.
11.1
Authentication unit (IC card type) AU-201
Using authentication unit (IC card type)
The authentication unit (IC card type) is an "IC card authentication " system that reads the IC card to perform
personal authentication. Using this system, you can perform authentication with an IC card to log in to this
machine or execute a print job when User Authentication is enabled in this machine.
To use the authentication unit, first register the card ID of the user in this machine. The registered user, who
is authenticated with the card ID, can log in to this machine or execute a print job. This section explains how
to configure the required settings in this machine, register users, and log in with authentication.
For details on how to place the IC card in the authentication unit, refer to the "Quick Guide
[Copy/Print/Fax/Scan/Box Operations]".
NOTICE
Authentication unit (IC card type) AU-201 must be installed inside the working table WT-506.
Do not disconnect the USB cable while using the authentication unit. Doing so may cause the system to
become unstable.
Do not leave the IC card within 1-9/16 inch (40 mm) of the card reader.
11.1.1
Configuring this machine
NOTICE
User authentication settings must be configured with MFP authentication on this machine.
This device does not support external server authentication. For the [Public User] or [Account Track] settings,
refer to page 7-31. To combine account track settings with user authentication settings, set Synchronize
User Authentication & Account Track to "Synchronize".
1
Use the control panel of this machine to display the Administrator Settings screen. Press [4 User
Authentication/Account Track], then [General Settings].
bizhub C652/C652DS/C552/C552DS/C452
11-2
11.1
Using authentication unit (IC card type)
2
Set [User Authentication] to "ON (MFP)", and then press [OK].
3
Press [Yes], and then [OK].
4
Press [8 Authentication Device Settings].
5
Press [1 General Settings].
6
Press [Card Authentication].
7
Configure "IC Card Type" and "Operation Settings".
11
% In "IC Card Type", specify the required IC card type.
% For "Operation Settings", specify how to log in to this machine after registration.
Card Authentication: Allows the user to log in by simply placing the IC card.
Card Authentication + Password: Allows the user to log in by placing the IC card and entering the
password.
For details on how to log in to this machine, refer to page 11-15.
bizhub C652/C652DS/C552/C552DS/C452
11-3
11.1
11.1.2
Using authentication unit (IC card type)
11
8
Press [OK] twice.
9
Press [2 Logoff Settings].
10
Specify whether to log out the user when scanning the original has finished after the user logged in with
the authentication unit.
11
Press [OK].
12
Press [Close] twice.
Registering a user
The following two methods can be used to register a user.
Connect the authentication unit to this machine, and directly register the target user in this machine
Connect the authentication unit to your computer, and use Data Administrator to register the target user
NOTICE
The registered user data is saved in the HDD of this machine. Changing the user authentication type of this
machine or formatting the HDD will erase the registered user data.
Registering a user using the control panel of this machine
1
Use the control panel of this machine to display the Administrator Settings screen. Press [4 User
Authentication/Account Track], and then [2 User Authentication Settings].
2
Press [2 User Registration].
3
Select a desired registration number, and then press [Edit].
bizhub C652/C652DS/C552/C552DS/C452
11-4
11.1
Using authentication unit (IC card type)
4
Press [Register Auth. Info.].
5
Press [Edit].
6
Place the IC card on the authentication unit, and press [OK].
7
When message [Registration complete] appears, press [Close] twice.
8
Enter the user name and password.
9
Configure function permission settings as required.
10
Press [OK].
11
Press [Close].
bizhub C652/C652DS/C552/C552DS/C452
11
11-5
11.1
Using authentication unit (IC card type)
11
Registering a user using Data Administrator
To use Data Administrator, configure this machine, and set up Data Administrator. For setup, install the IC
Card Driver (USB-Driver) of the authentication unit, and then install Data Administrator IC Card Plugin.
NOTICE
Before setup, install Data Administrator V4.0 or later in your computer. For the Data Administrator operating
environment and installation procedure, refer to the Data Administrator User's Guide.
Checking the version of the installed Data Administrator
1
From the "Help" menu of Data Administrator, select "Version Information".
NOTICE
This software cannot be used if the version is "3.x". Install "4.x".
If Data Administrator V3.x is installed, it is removed when V4.x is installed.
2
Click the [Plug-in version].
3
In "Plug-in information list", confirm the plugin version of Data Administrator.
% This software is available if the plugin version is "4.x".
bizhub C652/C652DS/C552/C552DS/C452
11-6
11.1
Using authentication unit (IC card type)
11
Setup
1
Turn the main power of this machine off, and disconnect the authentication unit from this machine.
2
Install IC Card Driver (USB-Driver).
Connect the authentication unit to the USB port of your computer.
The "Found New Hardware" dialog box appears.
3
Select "Locate and install driver software (recommended)".
4
Insert the application CD-ROM provided with the authentication unit into the CD-ROM drive of the
computer.
5
Click the "Browse my computer for driver software (advanced)".
bizhub C652/C652DS/C552/C552DS/C452
11-7
11.1
Using authentication unit (IC card type)
6
11
Check that the driver's search location is the application CD-ROM, and then click the [Next].
% When the driver's search location is not the application CD-ROM, click the [Browse]. Select the IC
Card Driver (USB-Driver) folder in the CD-ROM, and click the [OK].
% Installation starts.
bizhub C652/C652DS/C552/C552DS/C452
11-8
11.1
Using authentication unit (IC card type)
7
11
Click the [Close].
Installation of the IC Card Driver (USB-Driver) is completed.
8
Install Data Administrator IC Card Plugin.
Open the IC_Card_Plugin folder on the application CD-ROM, and then click setup.exe.
9
Select a language, and then click the [OK].
The installation program starts.
10
Follow the on-screen instructions to proceed with the installation.
11
Click the [Next].
bizhub C652/C652DS/C552/C552DS/C452
11-9
11.1
Using authentication unit (IC card type)
12
Select "I accept the terms in the license agreement", and then click the [Next].
13
Click the [Install].
14
Click the [Finish].
11
Installation of the Data Administrator IC Card Plugin is completed, which completes the setup.
bizhub C652/C652DS/C552/C552DS/C452
11-10
11.1
Using authentication unit (IC card type)
11
User registration
To register a user with Data Administrator, connect the authentication unit to the USB port of the computer,
and also connect the computer to this machine via network.
1
If the authentication unit is already connected to this machine, turn the main power switch of this
machine off, and then disconnect the authentication unit.
% When the authentication unit is already connected to the computer, go to step 4.
NOTICE
To turn the main power switch off and on, first turn the main power switch off, and then turn it on after
10 or more seconds has elapsed. Not doing so may result in an operation failure.
When connecting or disconnecting the USB cable, hold the plug. Otherwise, the cable may be
damaged.
2
Turn the main power on.
3
Connect the authentication unit to the USB port of the computer that contains Data Administrator.
NOTICE
Do not connect another USB device to the same port as for the authentication unit. Doing so reduces
the USB power supply, resulting in an operation failure.
To use the USB hub, be sure to connect the self-power USB hub that supplies 500 mA or more.
Restart the procedure 5 or more seconds after connecting the authentication unit.
4
Data Administrator starts, and device information of this machine is imported.
The Device Information window appears.
% For details on how to import device information, refer to the Data Administrator User 's Guide.
bizhub C652/C652DS/C552/C552DS/C452
11-11
11.1
Using authentication unit (IC card type)
5
In Select Function, select "Authentication Settings" - "User Setting", and then click the [Add].
6
Select the desired template, and then click the [OK].
11
The User Registration window appears.
bizhub C652/C652DS/C552/C552DS/C452
11-12
11.1
Using authentication unit (IC card type)
7
11
Enter the user name and password, and select the "IC card authentication" tab.
% Enter the E-mail address and other information as required.
8
Place the IC card on the authentication unit, and click the [Start reading].
% If necessary, click [Card ID Input] to register the card ID.
9
Click the [OK].
% Repeat steps 5 to 12 to register all users.
bizhub C652/C652DS/C552/C552DS/C452
11-13
11.1
Using authentication unit (IC card type)
10
11
Click [Export to the device].
% Select the user name and click the [Edit] to change the registered data.
11
Click the [Write].
% Data Administrator provides the batch copy function that batch-configures the registered user data
in multiple machines with the authentication unit enabled.
The registered user data is configured in this machine.
12
Click the [OK].
13
Disconnect the authentication unit from the USB port of the computer.
14
Turn the main power switch of this machine off, connect the authentication unit to this machine, and
turn the main power switch of this machine on.
bizhub C652/C652DS/C552/C552DS/C452
11-14
11.1
Using authentication unit (IC card type)
11
NOTICE
To turn the main power switch off and on, first turn the main power switch off, and then turn it on after
10 or more seconds has elapsed. Not doing so may result in an operation failure.
When connecting or disconnecting the USB cable, hold the plug. Otherwise, the cable may be
damaged.
11.1.3
Logging in to this machine
This section explains how to log in to this machine with IC card authentication.
To use authentication unit (IC card type), register the information recorded in the IC card in advance.
If authentication fails frequently, IC card information may not be registered properly. Register IC card
information again.
When the IC Card authentication is enabled, a registered user is authenticated by simply placing the IC
card. Authentication is carried out when you place the IC card and enter the password when both IC
cards and passwords are used for authentication.
Press [ID & PW] to log in by entering the user name and the password, without using the authentication
unit.
When IC card authentication is enabled
%
Place the IC card on the working table.
The basic settings screen appears.
bizhub C652/C652DS/C552/C552DS/C452
11-15
11.1
Using authentication unit (IC card type)
11
When IC card authentication + password authentication is enabled
1
Place the IC card on the working table.
2
Press [Password], and then enter the password.
3
Press either [Login] or the [Access] key.
The basic settings screen appears.
bizhub C652/C652DS/C552/C552DS/C452
11-16
12
Specifications
12.1
12
Paper
12
Specifications
This chapter describes the specifications of the paper, machine, and options.
This product specification is subject to change without notice toward the improvement.
12.1
Paper
Paper types and paper capacities
Paper type
Paper weight
Paper capacity
Plain paper
Single Side Only*1
Special Paper*2
Letterhead*3
Colored Paper*4
User Paper 1*5
User Paper 2*5
17 lb to 23-15/16 lb
(64 to 90 g/m2)
Bypass tray: 150 sheets, Tray 1/2: 500 sheets
Tray 3: 1,500 sheets, Tray 4: 1,000 sheets
Large capacity unit LU-301: 3,000 sheets
Large capacity unit LU-204: 2,500 sheets
Thick 1
User Paper 3*5
24-3/16 lb to
31-15/16 lb
(91 to 120 g/m2)
Bypass tray: 100 sheets, Tray 1/2: 400 sheets
Tray 3: 1,150 sheets, Tray 4: 750 sheets
Large capacity unit LU-301: 2,500 sheets
Large capacity unit LU-204: 2,000 sheets
Thick 1+
User Paper 4*5
32-3/16 lb to
41-3/4 lb
(121 to 157 g/m2)
Bypass tray: 80 sheets, Tray 1/2: 280 sheets
Tray 3: 800 sheets, Tray 4: 500 sheets
Large capacity unit LU-301: 1,750 sheets
Large capacity unit LU-204: 1,450 sheets
Thick 2
User Paper 5*5
42 lb to 55-5/8 lb
(158 to 209 g/m2)
Bypass tray: 70 sheets, Tray 1/2: 250 sheets
Tray 3: 700 sheets, Tray 4: 450 sheets
Large capacity unit LU-301: 1,550 sheets
Large capacity unit LU-204: 1,250 sheets
Thick 3
User Paper 6*5
55-7/8 lb to 68-1/8 lb
(210 to 256 g/m2)
Bypass tray: 60 sheets, Tray 1/2: 200 sheets
Tray 3: 600 sheets, Tray 4: 400 sheets
Large capacity unit LU-301: 1,300 sheets
Large capacity unit LU-204: 1,000 sheets
Thick 4
68-3/8 lb to
79-13/16 lb
(257 to 300 g/m2)
Bypass tray: 50 sheets
Transparency
-
Bypass tray: 20 sheets
Postcards
-
Bypass tray: 50 sheets
Tray 3: 200 sheets*, Tray 4: 200 sheets*
* Ask the service representative to change the setting.
Envelope
-
Bypass tray: 10 sheets
Label sheets
-
Bypass tray: 50 sheets
*1
Paper where you do not print on both sides (for example, when something is already printed on the front
side).
*2
Fine and other special paper.
*3
Paper where company names, preset text, and others are already printed.
*4
Colored paper.
*5
Paper that is registered as one of frequently used paper types.
For paper weight and media adjustment settings, contact your service representative.
bizhub C652/C652DS/C552/C552DS/C452
12-2
12.1
Paper
12
NOTICE
Paper other than plain paper, such as OHP transparencies and colored paper, is called special paper. Be sure
to select a special paper setting for paper trays loaded with media such as OHP transparencies and colored
paper.
If the paper size and paper type have not been correctly specified, a paper jam may occur or poor image
quality may result.
When you select Plain Paper, Thick 1, Thick 1+, Thick 2, Thick 3, or Thick 4 for the bypass tray, you can select
Duplex 2nd Side. Select Duplex 2nd Side when you load paper where something is printed on one side.
bizhub C652/C652DS/C552/C552DS/C452
12-3
12.2
12.2
Machine specifications
12
Machine specifications
bizhub C652/C652DS/C552/C552DS/C452
Specification
Type
Scanner, printer, desktop, or stand-alone
Document holder
Stationary (mirror scanning)
Photo conductor
OPC
Light source
White rare-gas fluorescent
Copy system
Laser electrostatic copying
Developing system
Dry 2-component HMT developing system
Fusing system
Belt fusing
Resolution
Scanning
600 dpi e 600 dpi
Output
1,800 dpi e 600 dpi
Type
Sheets, books (two-page spread), three-dimensional objects
Size
Max. 11 e17 (A3)
Weight
4-7/16 lb (2 kg) (three-dimensional objects)
Originals
Copying paper type
Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2)), Thick1 (24-3/16 lb to 3115/16 lb (91 to 120 g/m2)), Thick1+ (32-3/16 lb to 41-3/4 lb (121 to 157
g/m2)), Thick2 (42 lb to 55-5/8 lb (158 to 209 g/m2)), Thick3 (55-7/8 lb to
68-1/8 lb (210 to 256 g/m2)), Thick4 (68-3/8 lb to 79-13/16 lb (257 to 300
g/m2))*,
Letterhead, colored paper, transparency*, postcard**, envelope*, label
sheet*, banner paper (33-13/16 lb to 55-7/8 lb (127 to 210 g/m2))*
2 Sided: Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2)), Thick1/1+/2/3
(24-3/16 lb to 68-1/8 lb (91 to 256 g/m2))
* Available for bypass tray.
** Available for bypass tray or tray 3/4. (When using tray 3/4, ask the service
representative to change the setting.)
Copy paper size
<Tray 1/2>
12-1/4 e 18 w, 12 e 18 w to 8-1/2 e 11 v, A3 w to A5 w, 8 e 13 w*1,
16K v, 8K w
<Tray 3/4>
8-1/2 e 11 v, 5-1/2 e 8-1/2 v*, A4 v to A5 v, 16K v
<Bypass tray>*2
12-1/4 e 18 w, 12 e 18 w to 5-1/2 e 8-1/2 w/v, A3 w to B6 w, A6 w,
4 e 6 w, 8 e 13 w*1, A6 card w, 16K w/v, 8K w
Width: 3-9/16 to 12-1/4 (90 mm to 311.1 mm), length: 5-1/2 to 47-1/4
(139.7 mm to 1,200 mm)
*1
There are six types of foolcaps: 8-1/2 e 13-1/2 w, 220 e 330 mmw,
8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, and 8 e 13 w. Any one of
these sizes is selectable. For details, contact your service representative.
*2 Banner Paper
Width: 8-1/4 to 11-11/16 (210 to 297 mm)
Length: 18 to 47-1/4 (457 to 1,200 mm)
Number of sheets loaded in
output tray
Plain paper
250 sheets
Thick
10 sheets
Transparency
1 sheet
bizhub C652/C652DS/C552/C552DS/C452
12-4
12.2
Machine specifications
12
Specification
Number of loadable sheets
(8-1/2 e 11 (A4))
Tray 1 or 2
Plain paper: 500 sheets (21-1/4 lb (80 g/m2))/550
sheets (17 lb (64 g/m2)), Thick 1: 400 sheets,
Thick 1+: 280 sheets, Thick 2: 250 sheets, Thick
3: 200 sheets
Tray 3
Plain paper: 1,500 sheets (21-1/4 lb (80
g/m2))/1,650 sheets (17 lb (64 g/m2)), Thick 1:
1,150 sheets, Thick 1+: 800 sheets, Thick 2: 700
sheets, Thick 3: 600 sheets, Postcard: 200 sheets
Tray 4
Plain paper: 1,000 sheets (21-1/4 lb (80
g/m2))/1,100 sheets (17 lb (64 g/m2)), Thick 1: 750
sheets, Thick 1+: 500 sheets, Thick 2: 450 sheets,
Thick 3: 400 sheets, Postcard: 200 sheets
Bypass tray
Plain paper: 150 sheets (21-1/4 lb (80 g/m2)),
Thick 1: 100 sheets, Thick 1+: 80 sheets, Thick 2:
70 sheets, Thick 3: 60 sheets, Thick 4: 50 sheets,
Transparency: 20 sheets, Postcard or label sheet:
50 sheets, Envelope: 10 sheets
Warm-up time
Period from the time the [main power switch] was turned on to the time
[sub power switch] was turned on to get ready for printing (room temperature is 73.4 °F (23 °C))
C652/C652DS: 30 sec. or less
C552/C552DS: 60 sec. or less
C452: 60 sec. or less (Black: 30 sec. or less)
Period from the time [main power switch] was turned on to the time this
machine is ready for printing (room temperature is 73.4 °F (23 °C))
C652/C652DS: 39 sec. or less
C552/C552DS: 39 sec. or less
C452: 60 sec. or less (Black: 45 sec. or less)
Warm-up time may vary depending on the operating environment and usage.
Image chipping width
Top edge
3/16 (4.2 mm)
Bottom edge
1/8 (3.0 mm)
Right edge
1/8 (3.0 mm)
Left edge
1/8 (3.0 mm)
First copy
(When 8-1/2 e 11 v (A4 v)
printing)
bizhub C652/C652DS/C552/C552DS/C452
C652/C652DS
Full color: 5.5 sec. or less
Black: 3.8 sec. or less
C552/C552DS
Full color: 6.0 sec. or less
Black: 4.3 sec. or less
C452
Full color: 6.0 sec. or less
Black: 4.8 sec. or less
12-5
12.2
Machine specifications
12
Specification
Copy speed (When 8-1/2 e
11 (A4) printing)
Full Color
(Simplex/Duplex)
C652/C652DS
Plain paper: 50 sheets/min., Thick1 or 1+: 32
sheets/min., Thick2, 3 or 4, Special paper, Glossy
mode: 25 sheets/min.
C552/C552DS
Plain paper: 45 sheets/min., Thick1 or 1+: 28
sheets/min., Thick 2, 3 or 4, Special paper,
Glossy mode: 23 sheets/min.
C452
Plain paper: 45 sheets/min., Thick1 or 1+: 28
sheets/min., Thick2, 3 or 4, Special paper, Glossy
mode: 23 sheets/min.
Black
(Simplex/Duplex)
C652/C652DS
Plain paper: 65 sheets/min., Thick1 or 1+: 32
sheets/min., Thick2, 3 or 4, Special paper, Glossy
mode: 25 sheets/min.
C552/C552DS
Plain paper: 55 sheets/min., Thick1 or 1+: 28
sheets/min., Thick2, 3 or 4, Special paper, Glossy
mode: 23 sheets/min.
C452
Plain paper: 45 sheets/min., Thick1 or 1+: 28
sheets/min., Thick2, 3 or 4, Special paper, Glossy
mode: 23 sheets/min.
Copy magnification
Full size: 100.0% ± 0.5%
Enlarge: 121.4%, 129.4%, 154.5%, or 200.0% (115.4%, 122.4%, 141.4%,
or 200.0%)
Reduce: 78.5%, 73.3%, 64.7%, or 50.0% (86.6%, 81.6%, 70.7%, or
50.0%)
Manual: 25.0 to 400.0% (in 0.1% steps)
Number of continuous
copies
1 to 9999 sheets
Density adjustment
Copy density
Manual density adjustment (9 levels)
Background density
Manual or automatic density adjustment (9 levels)
Power supply
North American model (inch): AC 120 V, 16 A, 60 Hz
European model (cm): AC 220 - 240 V, 10 A, 50/60 Hz
Max. power consumption
C652/C652DS: 2,100W
C552/C552DS: 2,000 W
C452: 2,000 W
Size
Width 25-9/16 e Depth 30-9/16 (excluding panel)/34-5/8 (including
panel) e Height 45-1/2 (including ADF)
(Width 650 mm e Depth 777 mm (excluding panel)/879 mm (including
panel) e Height 1,155 mm (including ADF))
Machine occupation dimensions
C652/C652DS/C552/C552DS:
Width 100-9/16 e Depth 60-1/16 e Height 64-15/16
(Width 2,554 mm e Depth 1,525 mm e Height 1,650 mm)
The dimensions above are measured when the finisher (FS-526) tray extension, paper trays and LCU (LU-204) are pulled out, and the ADF is open.
C452:
Width 84-9/16 e Depth 60-1/16 e Height 64-15/16
(Width 2,148mm e Depth 1,525mm e Height1,650mm)
The dimensions above are measured when the finisher (FS-527) tray extension and paper trays and LCU (LU-204) are pulled out, and the ADF is
open.
Memory size (hard disk capacity)
2,048 MB (250 GB)
Weight
bizhub C652/C552/C452 :Approx. 487-13/16 lb (Approx. 221 kg)
bizhub C652DS/C552DS :Approx. 223 kg
bizhub C652/C652DS/C552/C552DS/C452
12-6
12.2
Machine specifications
12
Automatic duplex unit
Specification
Paper type
Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2)), Thick1 (24-3/16 lb to 3115/16 lb (91 to 120 g/m2)), Thick1+ (32-3/16 lb to 41-3/4 lb (121 to 157
g/m2)), Thick2 (42 lb to 55-5/8 lb (158 to 209 g/m2)), Thick3 (55-7/8 lb to
68-1/8 lb (210 to 256 g/m2))
Paper size
12-1/4 e 18 w, 12 e 18 w to 5-1/2 e 8-1/2 w, A3 w to B6 w, A6 w, 8 e 13
w*1, 16K w/v, 8K w, 4 e 6 w
Width: 3-15/16 to 12-1/4 (100 to 311.1 mm), Length: 5-13/16 to 18 (148 to
457.2 mm)
*1
There are six types of foolcaps: 8-1/2 e 13-1/2 w, 220 e 330 mmw,
8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, and 8 e 13 w. Any one of
these sizes is selectable. For details, contact your service representative.
Power supply
Supply from machine
Reverse automatic document feeder (bizhub C652/C552/C452)
Specification
Original feed function
1-sided original, 2-sided original, mixed original
Original types
1-sided
Plain paper (9-5/16 lb to 55-7/8 lb (35 to 210
g/m2))
2-sided, mixed original
Plain paper (13-5/16 lb to 34-1/16 lb (50 to 128
g/m2))
Original Size
1-Sided/2-Sided Originals: 11 e 17 w to 5-1/2 e 8-1/2 w/v, A3 w to B6 w,
A6 w, 8 e 13 w
For details on handling mixed originals, refer to p. 5-16.
Original loading capacity
1- or 2-sided original: Max. 100 sheets (21-1/4 lb (80 g/m2))
Power supply
Supply from machine
Max. power consumption
60 W or less
Size
Width 24-5/16 e Depth 22-5/8 e Height 5-1/8
(Width 618 mm e Depth 575 mm e Height 130 mm)
Weight
Approx. 35-1/4 lb (Approx. 16 kg)
Reverse automatic document feeder (bizhub C652DS/C552DS)
Specification
Original feed function
1-sided original, 2-sided original, mixed original
Original types
1-sided, 2-sided
Plain paper (9-5/16 lb to 55-7/8 lb (35 to 210
g/m2))
mixed original
Plain paper (13-5/16 lb to 34-1/16 lb (50 to 128
g/m2))
Original Size
1-Sided/2-Sided Originals: 11 e 17 w, 8-1/2 e 11 w/v, A3 w to B6 w, A6
w, 8 e 13 w
For details on handling mixed originals, refer to p. 5-16.
Original loading capacity
1- or 2-sided original: Max. 100 sheets (21-1/4 lb (80 g/m2))
Power supply
Supply from machine
Max. power consumption
80 W or less
Size
Width 24-5/16 e Depth 22-5/8 e Height 5-1/8
(Width 618 mm e Depth 575 mm e Height 129 mm)
Weight
Approx. 39-11/16 lb (Approx. 18 kg)
bizhub C652/C652DS/C552/C552DS/C452
12-7
12.3
12.3
Options
12
Options
Large capacity unit LU-301
Specification
Paper type
Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2)), Thick 1 (24-3/16 lb to 3115/16 lb (91 to 120 g/m2)), Thick 1+ (32-3/16 lb to 41-3/4 lb (121 to 157
g/m2)), Thick 2 (42 lb to 55-5/8 lb (158 to 209 g/m2)), Thick 3 (55-7/8 lb to
68-1/8 (210 to 256 g/m2))
Paper size
8-1/2 e 11 v, A4 v
Number of loadable sheets
Plain paper: 3,000 sheets (21-1/4 lb (80 g/m2))/3,300 sheets (17 lb (64
g/m2)), Thick 1: 2,500 sheets, Thick 1+: 1,750 sheets, Thick 2: 1,550
sheets, Thick 3: 1,300 sheets
Power supply
Supply from machine
Max. power consumption
22W or less
Size
Width 14-7/16e Depth 20-13/16e Height 15-15/16
(Width 367 mm e Depth 528 mm e Height 405 mm)
Weight
Approx. 39-11/16 lb (Approx. 18 kg)
Large capacity unit LU-204
Specification
Paper type
Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2)), Thick 1 (24-3/16 lb to 3115/16 lb (91 to 120 g/m2)), Thick 1+ (32-3/16 lb to 41-3/4 lb (121 to 157
g/m2)), Thick 2 (42 lb to 55-5/8 lb (158 to 209 g/m2)), Thick 3 (55-7/8 lb to
68-1/8 lb (210 to 256 g/m2))
Paper size *
12 e 18 w, 11 e 17 w to 8-1/2 e 11 w/v, A3w, B4 w, A4 w/v
Number of loadable sheets
Plain paper: 2,500 sheets (21-1/4 lb (80 g/m2))/2,750 sheets (17 lb (64
g/m2)), Thick 1: 2,000 sheets, Thick 1+: 1,450 sheets, Thick 2: 1,250
sheets, Thick 3: 1,000 sheets
Power supply
Supply from machine
Max. power consumption
22W or less
Size
Width 24-3/4e Depth 21-7/8e Height 15-15/16
(Width 629 mm e Depth 556 mm e Height 405 mm)
Weight
Approx. 55-1/8 lb (Approx. 25 kg)
*
The maximum number of loadable sheets for each paper size is 2,500 sheets (for 21-1/4 lb (80 g/m2)) or
2,750 sheets (for 17 lb (64 g/m2)).
bizhub C652/C652DS/C552/C552DS/C452
12-8
12.3
Options
12
Finisher FS-526
Specification
Output tray
Feeding function
Output tray 1, output tray 2
Group, Sort, Offset Group*, Offset Sort*, Staple*
Fed into output tray 2
*
Paper type
Plain paper (15-15/16 lb to 23-15/16 lb (60 to 90 g/m2))
Thick (24-3/16 lb to 79-13/16 lb (91 to 300 g/m2)), transparency, postcard, envelope, label sheet, letterhead paper, colored paper
Staple: Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2))
Thick (24-3/16 lb to 55-5/8 lb (91 to 209 g/m2))*
*Can be used only as a cover page
Paper size
<Output tray 2> (Main Tray)
12 e 18 w to 5-1/2 e 8-1/2 w/v, A3 w to A6 w/v, 8 e 13 w*1, 16K w/v, 8K w
Width: 3-15/16 to 13 (100 to 330.2 mm), length: 5-1/2 to 19-1/4 (139 to 488 mm)
Staple: 11 e 17 w to 8-1/2 e 11 w/v, A3 w to B5 w/v, A5 v, 8 e 13 w*1,
5-1/2 e 8-1/2 v, 16K w/v, 8K w,
Width: 7-3/16 to 13 (182 to 330 mm), length: 5-1/2 to 19-1/4 (139 to 488 mm)
<Output tray 1> (Sub Tray)
13 e 19 w to 5-1/2 e 8-1/2 w/v, A3 w to A5 w/v, B6 w, A6 w, 8 e 13 w*1, 11 e 17
w, 16K w/v, 8K w
Width: 3-15/16 to 13-1/16 (100 to 331 mm), length: 5-1/2 to 19-1/4 (139 to 488
mm)
*1
There are six types of foolcaps: 8-1/2 e 13-1/2 w, 220 e 330 mmw,
8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, and 8 e 13 w. Any one of these sizes is selectable. For details, contact your service representative.
Paper loading capacity
< Output tray 2>
Group/Sort
3,000 sheets*1(11 e 8-1/2 w/v, 7-1/4 e 10-1/2 w/v, A4
w/v, B5 w/v, 16K w/v)
1,500 sheets (12 e 18 w*2, 8-1/2 e 14 w, A3 w, B4 w,
8 e 13 w*3, 8K w)
500 sheets (5-1/2 e 8-1/2 w/v, A5 w/v, B6 w, A6 w)
*1 2,500 sheets when saddle stitcher SD-508 is installed.
*2 12 e 18 is 304.8 e 457.2 mm that is one-size larger
than A3.
*3 There are six types of foolcaps: 8-1/2 e 13-1/2 w, 220
e 330 mm w, 8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 131/4 w, 8 e 13 w. Any one of these sizes is selectable.
For details, contact your service representative.
Offset Group/Offset
Sort
When the length
of paper is 515/16 to 12-5/8
(150 mm to 320
mm)
300 sets
When the length
of paper is other
than 5-15/16 to
12-5/8
(150 mm to 320
mm)
150 sets
bizhub C652/C652DS/C552/C552DS/C452
12-9
12.3
Options
12
Specification
Staple
11 e 17 w, A3 w
Other than 11 e 17
w, A3 w
2 sheets-9
sheets
50 sets
10 sheets-20
sheets
50 sets
21 sheets-30
sheets
30 sets
31 sheets-40
sheets
25 sets
41 sheets-50
sheets
20 sets
2 sheets-9
sheets
100 sets
10 sheets-20
sheets
50 sets
21 sheets-30
sheets
30 sets
31 sheets-40
sheets
25 sets
41 sheets-50
sheets
20 sets
51 sheets-60
sheets
15 sets
61 sheets-100
sheets
10 sets
Paper loading capacity
< Output tray 1>
100 sheets
Maximum number of
stapled sheets
Plain paper (17 to
23-15/16 lb (64 to 90
g/m2))
100 sheets
Shift amount
1-3/16 (30 mm)
Power supply
Supply from machine
Max. power consumption
105 W or less (when all applicable options are installed)
Size
Width 28-1/2 (Main tray is pulled output: 33-7/16, Sub tray is pulled output: 3411/16) e Depth 27-15/16 e Height 40-3/8
(Width 723.8 (Main tray is pulled output: 848.8 mm, Sub tray is pulled output:
881.2 mm) mm e Depth 709.5 e Height 1,025 mm)
Weight
Approx. 132-1/4 lb (Approx. 60 kg)
Consumables
Staples MS-10A
For EH-1028 (Product No. 1002 manufactured by MAX) (5,000 staples included)
e 1 unit
Saddle stitcher SD-508
Specification
Feeding function
Center Staple and Fold, Half-Fold, Tri-Fold
(Belt conveyer feeding)
Paper type
Center Staple and Fold: Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2))
Half-Fold or Tri-Fold: Plain paper (17 lb to 23-15/16 lb (64 to 90 g/m2))
bizhub C652/C652DS/C552/C552DS/C452
12-10
12.3
Options
12
Specification
Paper size
Center Staple and Fold, Half-Fold: 12 e 18 w to 8-1/2 e 11 w, A3w, B4w,
A4w, 8K w
Width: 8-1/4 to 12-3/8 (210 mm to 314 mm), length: 11 to 18-1/16 (279 mm
to 458 mm)
Tri-Fold: 8-1/2 e 11 w, A4w, 16K w
Maximum number of
sheets that can be centerstapled
20 sheets, 19 sheets (21-1/4 lb (80 g/m2)) or 16 sheets (23-15/16 (90 g/m2))
+ Thick (55-5/8 lb (209 g/m2)) 1 sheet
Maximum number of folded sheets
Half-Fold: 3 sheets
Tri-Fold: 3 sheets
Number of sheets that can
be loaded into the folding
output tray
Plain paper (21-1/4 lb (80
g/m2))*
When the length of paper is 13
(330 mm) or more
When the length of paper is 13
(330 mm) than less
*
One sheet folded
20 sets
Two sheets stapled
and folded
18 sets
Three sheets stapled
and folded
15 sets
Four sheets stapled
12 sets
Five sheets stapled
8 sets
Six to 15 sheets stapled
5 sets
16 to 20 sheets stapled
5 sets
Tri-Fold
-
One sheet folded
10 sheets
Two sheets stapled
and folded
10 sets
Three sheets stapled
and folded
10 sets
Four sheets stapled
5 sets
Five sheets stapled
5 sets
Six to 15 sheets stapled
5 sets
16 to 20 sheets stapled
4 sets
Tri-Fold
20 sets
Size
Width 11-1/16e Depth 23-1/4e Height 20-7/8
(Width 281.3 mm e Depth 596.4 mm e Height 529.8 mm)
Weight
Approx. 49-13/16 lb (Approx. 22.6 kg), Approx. 8-3/8 lb (Approx. 3.8 kg)
(Output tray)
Consumables
Staple MS-5C
For EH-554 (Product No. 500 manufactured by MAX) (5,000 staples included) e 1 unit
Power supply
Supply from finisher
Not applicable to multi-function jobs (jobs with multiple functions combined).
Punch kit PK-516
Specification
Number of punch holes
2 holes, 3 holes or 4 holes
Paper type
Plain paper (17-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)),
Thick (24-3/16 lb to 79-13/16 lb (91 g/m2 to 300 g/m2))
bizhub C652/C652DS/C552/C552DS/C452
12-11
12.3
Options
12
Specification
Paper size
"2-Hole" Punch setting:
11 e 17 w to 5-1/2 e 8-1/2 w, A3w to A5w/v, 8 e 13 w*, 16K w/v, 8K w,
7-1/4 e 10-1/2 w/v
"3-Hole"/"4-Hole" Punch settings:
A3 w, B4 w, A4 v, B5 v, 11 e 17 w, 8-1/2 e 11 v, 7-1/4 e 10-1/2 v, 8K w,
16K v
*
There are four types of foolcaps:
8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, 8 e 13 w. Any one of these
sizes is selectable. For details, contact your service representative.
Power supply
Supply from finisher
Size
Width 5-3/4 e Depth 25-3/16e Height 9-3/16
(Width 146.2 mm e Depth 639.2 mm e Height 233.8 mm)
Weight
Approx. 9-15/16 lb (4.5 kg)
Job Separator JS-602
Specification
Output tray
Output tray 3
Feeding function
Group, Sort
Paper type
Plain paper (17 lb to 23-15/16 lb (64 g/m2 to 90 g/m2))
Paper size
11 e 17 w - 5-1/2 e 8-1/2 w, 8 e 13 w*, A3 w to A5 w
There are five types of foolcaps:
8-1/2 e 13-1/2 w, 8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, 8 e 13 w.
Any one of these sizes is selectable. For details, contact your service representative.
Paper loading capacity
Plain paper (80 g/m2)
*
8-1/2 × 11 w, A4 w
100 sheets
Other than 8-1/2 × 11
w, A4 w
50 sheets
Size
Width 13-7/16 e Depth 21-1/8 e Height 5-7/8
(Width 341 mm e Depth 537 mm e Height 149 mm)
Weight
Approx. 3-7/8 lb (Approx. 1.75 kg)
Z-Folding Unit ZU-606
Specification
Number of punch holes
2 holes, 3 holes, 4 holes
Paper type when hole
punching is selected
Plain paper 17 lb to 23-15/16 lb (64g/m2 - 90g/m2)
Paper size when hole
punching is selected
11 e 17 w - 5-1/2 e 8-1/2 w/v, 8 × 13 w*, A3 w to A5 w/v
*
There are four types of foolcaps:
8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, 8 e 13 w. Any one of these
sizes is selectable. For details, contact your service representative.
Fold type
Z-Fold
Paper type when Z-folding
is selected
Plain paper (64g/m2 - 90g/m2)
Paper size when Z-folding
is selected
11 e 17 w, 8-1/2 e 14 w, A3 w, B4 w
Power supply
Supply from electrical outlet
Size
Width 6-11/16 e Depth 26 e Height 40-7/16
(Width 169.7 mm e Depth 660 mm e Height 1027.5 mm)
Weight
Approx. 99-3/16 lb (Approx. 45 kg)
bizhub C652/C652DS/C552/C552DS/C452
12-12
12.3
Options
12
Post Inserter PI-505
Specification
Configuration
2 trays (upper and lower)
Cover paper type
Plain paper 17 lb to 23-15/16 lb (64-90g/m2), Thick 24-1/4 lb to 55-5/8 lb
(91 g/m2-209 g/m2)
Cover paper size
<Upper Tray>
8-1/2 e 11 w/v, 7-1/4 e 10-1/2 w/v, 5-1/2 e 8-1/2/v, A4 w/v to A5 v, 16K
w/v
Width: 7-3/16 to 12-1/4 (182 mm to 311.1 mm)
Length: 5-1/2 to 11-11/16 (139 mm to 297 mm)
<Lower Tray>
12 e 18 w, 11 e 17 w, 8-1/2 e 14 w, 8-1/2 e 11 w/v, 7-1/4 e 10-1/2 w/v,
5-1/2 e 8-1/2 v, 8 e 13 w*1, A3 w to 5 v, 16K w/v, 8K w, SRA4 w
Width: 7-3/16 to 12-1/4 (182 mm to 311.1 mm)
Length: 5-1/2 to 11-11/16 (139 mm to 457.2 mm)
*1 There are four types of foolcaps: 8-1/2 e 13-1/2 w, 220 e 330 mm w, 81/2 e 13 w, 8-1/4 e 13 w.
Any one of these sizes is selectable. For details, contact your service representative.
Paper loading capacity
Plain paper 21-1/4 lb (80 g/m2)
Power supply
Supply from finisher
Size
Width 20-1/8 e Depth 25 e 8-11/16
(Width 511 mm e Depth 635 mm e Height 220 mm)
Weight
Approx. 23-1/8 lb (Approx. 10.5 kg)
200 sheets for each tray
Finisher FS-527
Specification
Output tray
Output tray 1, Output tray 2
Feeding function
Group, Sort, Offset Group*, Offset Sort*, Staple*
* Fed into Output tray 2
Paper type
Group/Sort: Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)),
Thick (24-3/16 lb to 79-13/16 lb (91 g/m2 to 300 g/m2)), Transparency,
Postcards, Envelope, Label sheets, letterhead paper, banner paper
Offset Group/ Offset Sort: Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2
to 90 g/m2)), Thick (24-3/16 lb to 79-13/16 lb (91 g/m2 to 300 g/m2))
Staple: Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)), Thick
(24-3/16 lb to 82-7/16 lb (91 g/m2 to 310 g/m2))*
* There is a limit on the number of sheets.
Paper size
< Output tray 1 >
12-1/4 e 18 w, 11 e 17 w to 5-1/2 e 8-1/2 w/v, A3 w to B6 w, A6 w
Width: 3-9/16 to 12/1/4 (90 mm to 311.15 mm), Length: 5-1/2 to 47-1/4
(139.7 mm to 1200 mm)
< Output tray 2 >
Group/Sort:
12-1/4 e 18 w, 11 e 17 w to 5-1/2 e 8-1/2 w/v, A3 w to B6 w, A6 w
Width: 3-15/16 to 12-1/4 (100 mm to 311.15 mm), Length: 5-1/2 to 18
(139.7 mm to 457.2 mm)
Offset Group / Offset Sort:
12-1/4 e 18 w, 11 e 17 w, 8-1/2 e 14 w, 8-1/2 e 11 w/v, A3 w to A5 w
Width: 7-3/16 to 12-1/4 (182 mm to 311.15 mm), Length: 5-7/8 to 18 (148.5
mm to 457.2 mm)
Staple:
11 e 17 w, 8-1/2 e 11 w/v, A3 w to A5 v
Width: 7-3/16 to 11-1/4 (182 mm to 297 mm), Length: 5-7/8 to 17(148.5
mm to 431.8 mm)
bizhub C652/C652DS/C552/C552DS/C452
12-13
12.3
Options
12
Specification
Paper loading capacity
< Output tray 1>
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90
g/m2))
200 sheets
Thick (24-3/16 lb to 79-13/16 lb (91 g/m2 to 300 g/m2)),
Transparency, Postcards, Envelope, Label sheets, letterhead paper
20 sheets
Paper loading height: 1-3/8 (35 mm)
Paper loading capacity
< Output tray 2>
Group/Sort
Plain paper (1515/16 lb to 2315/16 lb (60
g/m2 to 90
g/m2))
8-1/2 × 11 w,
A4 w or less
3000 sheets
8-1/2 × 14 w,
B4 w or more
1500 sheets
5-1/2 × 8-1/2
w, A5 w or less
500 sheets
Thick (24-3/16 lb to 79-13/16 lb (91
g/m2 to 300 g/m2)), Transparency,
Postcards, Envelope, Label sheets,
letterhead paper
Offset Group /
Offset Sort
Staple
Plain paper (1515/16 lb to 2315/16 lb (60
g/m2 to 90
g/m2))
Plain paper (1515/16 lb to 2315/16 lb (60
g/m2 to 90
g/m2))
20 sheets
8-1/2 × 11 w,
A4 w or less
3000 sheets
8-1/2 × 14 w,
B4 w or more
1500 sheets
5-1/2 × 8-1/2
w, A5 w or less
500 sheets
2 sheets-9 sheets: 100 sets *
* 8-1/2 × 14 w, B4 w or more: 50
sets
10 sheets-20 sheets: 50 sets
21 sheets-30 sheets: 30 sets
31 sheets-40 sheets: 25 sets
41 sheets-50 sheets: 20 sets
Paper loading height: 14-3/4 (375 mm) (8-1/2 × 11 w, A4 w or less)/7-3/8
(187.5 mm) (8-1/2 × 14 w, B4 w or more)
Maximum number of folded sheets
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)): 50 sheets
Thick (24-3/16 lb to 31-15/16 lb (91g/m2 to 120 g/m2)): 30 sheets
Thick (32-3/16 lb to 55-5/8 lb (121 g/m2 to 209 g/m2)): 15 sheets
Example number of stapled sheets: Thick (55-5/8 lb (209 g/m2)) 2 sheets +
Plain paper 23-15/16 lb (90 g/m2) 48 sheets
Shift amount
1-/16 (30 mm)
Power supply
Supply from machine
Max. power consumption
56 W or less
Size
Width 20-13/16 (25-7/8) e Depth 25-1/4 e Height 48-3/8
(Width 528 (658) mm e Depth 641 mm e Height 1025 (1087) mm)
The numbers enclosed in parentheses ( ) indicate the values applied when
the tray is pulled output
Weight
Approx. 92-5/8 lb (Approx. 42 kg)
Consumables
Staples SK-602
For EH-590 (Product No.505 manufactured by MAX) (5,000 staples included) e 1 unit
Saddle stitcher SD-509
Specification
Feeding function
bizhub C652/C652DS/C552/C552DS/C452
Center Staple and Fold, Half-Fold
12-14
12.3
Options
12
Specification
Paper type
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)) Thick 24-3/16
lb to 55-5/8 lb (91 g/m2 - 209 g/m2)*
* Can be used only as a cover page
Paper size
12-1/4 × 18 w, 11 × 17 w, 8-1/2 × 14 w, 8-1/2 × 11 w, A3 w, B4 w, A4 w
Width: 8-1/4 to 12-14 (210 mm to 311.15 mm), Length: 11 to 18 (279.4 mm
to 457.2 mm)
Maximum number of
sheets that can be centerstapled
15 sheets, 14 sheets (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2))+ 1
sheets 15-15/16 lb to 55-5/8 lb (60 g/m2 to 209 g/m2)
Maximum number of folded sheets
3 sheets
Number of sheets that can
be loaded into the folding
output tray
Number of stapled
and folded sheets
1 sheets - 3 sheets
20 sets
4 sheets- 10 sheets
10 sets
11 sheets- 15 sheets
5 sets
Size
Width 9-7/16 e Depth 22-13/16 e Height 21
(Width 239 mm e Depth 579 mm e Height 534 mm)
Weight
Approx. 52-15/16 lb (Approx. 24 kg)
Consumables
Staples SK-602
For EH-280 (Product No.505 manufactured by MAX) (5,000 staples included) e 2 unit
Power supply
Supply from finisher FS-527
Punch Kit PK-517
Specification
Number of punch holes
2 holes, 3 holes or 4 holes
Paper type
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)), Thick 24-3/16
lb to 68-1/8 lb (91 g/m2 to 256 g/m2)
Paper size
"2-Hole"/"3-Hole" Punch settings
11 × 17 w to 8-1/2 × 11 w/v, A3 w to B5 w/v, 16K w/v, 8K w
A3 w, B4 w, A4 v, B5 v, 11 e 17 w, 8-1/2 e 11 v, 7-1/4 e 10-1/2 v, 8K w,
16K v
Power supply
Supply from finisher FS-527
Size
Widht 2-5/16 e Depth 18-1/2 e Height 5-5/16 inch
(Width 58 mm e Depth 470 mm e Height 135 mm)
Weight
Approx. 3-15/16 lb (Approx. 1.8 kg)
Job Separator JS-504
Specification
Output tray
Output tray 1, Output tray 2
Feeding function
Group, Sort, Offset Group, Offset Sort
Paper type
<Output tray 1> Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90
g/m2))
<Output tray 2> Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90
g/m2)), Thick 24-3/16 lb to 72-1/16 lb (91 g/m2 - 271 g/m2), Transparency,
Postcards, Label sheets, Envelope, Banner paper
Paper size
12-1/4 e 18 w, Postcards, Banner Paper, 11 e 17 w - 5-1/2 e 8-1/2 w/v,
A3 w to B6 w, A6 w
bizhub C652/C652DS/C552/C552DS/C452
12-15
12.3
Options
12
Specification
Paper loading capacity
<Output tray 1> Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90
g/m2)): 50 sheets
<Output tray 2> Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90
g/m2)): 150 sheets, Thick 24-3/16 lb to 72-1/16 lb (91 g/m2 - 271 g/m2),
Transparency, Postcards, Label sheets: 20 sheets
Envelope: 10 sheets
Banner Paper: 1 sheets
Power supply
Supply from machine
Max. power consumption
40 W or less
Shift amount
1-3/16 (30 mm)
Offset function
<Output tray 2> Plain paper, Thick 11 e 17 w to 8-1/2 e 11 w/v, A3 w to
B5 w
Size
Width 16-1/4 (413 mm)/21-8/5 (550 mm) (when tray extension is pulled out)
e Depth 18-3/4 (477 mm) e Height 5-1/16 (129 mm)
Weight
Approx. 11-1/4 lb (Approx. 5 kg)
Job Separator JS-603
Specification
Output tray
Output tray 3
Feeding function
Group, Sort
Paper type
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)), Thick 24-3/16
lb to 68-1/8 lb (91 g/m2 -256 g/m2), Transparency, Envelope, Label sheets,
Letterhead Paper
Paper size
12-1/4 e 18 w, 11 e 17 w to 5-1/2 e 8-1/2 w, A3 w to A5 w
Paper loading capacity
Plain paper (15-15/16 lb to 23-15/16 lb (60 g/m2 to 90 g/m2)): 100 sheets,
Thick (24-3/16 lb to 79-13/16 lb (91 g/m2 to 300 g/m2)), Transparency, Envelope, Label sheets, Letterhead Paper: 10 sheets
Paper loading height: 7/8 (22 mm)
Size
Width 14-7/16 e Depth 20-13/16 e Height 15-15/16 inch
(Width 165 mm e Depth 389 mm e Height 63 mm)
Weight
Approx. 2-3/16 lb (Approx. 1 kg)
Authentication unit (biometric type) AU-101
Specification
Name
AU-101
Applied finger width
3/8 to 1 (10 to 25 mm)
Interface
USB 2.0
Dimensions
Approx. 3-1/16 (W) e 3-3/4 (D) e 2-3/16 (H)
(Approx. 78 mm (W) e 95 mm (D) e 55 mm (H))
Weight
Approx. 5/16 lb (Approx. 150 g) (excluding USB
cable)
Max. power consumption (mA)
DC 5 V 500 mA
System conditions (during
operation)
Ambient temperature
50 ºF to 95 ºF (10 ºC to 35 ºC)
Humidity
10% to 80% (No dew condensation)
System conditions (during
non-operation)
Ambient temperature
14 ºF to 140 ºF (-10 ºC to 60 ºC)
Humidity
10% to 80% (No dew condensation)
bizhub C652/C652DS/C552/C552DS/C452
12-16
12.3
Options
12
Specification
Compatible computer
CPU
PC/AT compatible, 1 GHz or more
Memory
128 MB or more
HDD
Free space: 100 MB or more
Monitor
800 e 600 pixels, 16-bit color or more
Network
TCP/IP
Application
Microsoft Internet Explorer 6.0 (SP1) or later
Microsoft .NET Framework (SP1) or later
Interface
USB 1.1 or later
Supported Operating Systems
Windows 2000 Professional (SP4)
Windows XP Professional Edition (SP2)
Windows Vista Business/Enterprise
Authentication unit (biometric type) AU-102
Specification
Name
AU-102
Biometric sensor system
Transmission-type optical system
Verification time
Approx. 1 sec. or less
Interface
USB 2.0
Dimensions
Approx. 2-5/16 (W) e 3-1/4 (D) e 2-15/16 (H)
(Approx. 59 mm (W) e 82 mm (D) e 74 mm (H))
Weight
Approx. 3/16 (96 g) (excluding USB cable)
Max. power consumption (mA)
DC 5 V 500 mA
System conditions (during
operation)
Ambient temperature
41 ºF to 95 ºF (5 ºC to 35 ºC)
Humidity
20% to 80% (No dew condensation)
System conditions (during
non-operation)
Ambient temperature
32 ºF to 122 ºF (0 ºC to 50 ºC)
Humidity
20% to 80% (No dew condensation)
Compatible computer
CPU
PC/AT compatible, 1 GHz or more
Memory
128 MB or more
HDD
Free space: 100 MB or more
Monitor
800 e 600 pixels, 16-bit color or more
Network
TCP/IP
Application
Microsoft Internet Explorer 6.0 (SP1) or later
Microsoft .NET Framework (SP1) or later
Interface
USB 1.1 or later
Supported Operating Systems
Windows 2000 Professional (SP4)
Windows XP Professional Edition (SP2)
Windows Vista Business/Enterprise
Authentication unit (IC card type) AU-201
Specification
Name
AU-201
Dimensions
Approx. 3-5/8 (W) e 2-1/2 (D) e 5/8 (H)
(Approx. 92 mm (W) e 64 mm (D) e 16 mm (H))
Weight
Approx. 1/4 lb (Approx. 120 g)
Power supply
Power received from USB port
bizhub C652/C652DS/C552/C552DS/C452
12-17
12.3
Options
12
Specification
System conditions (during
operation)
Ambient temperature
32 ºF to 104 ºF (0 ºC to 40 ºC)
Humidity
20% to 85% (No dew condensation)
System conditions (during
non-operation)
Ambient temperature
-4 ºF to 122 ºF (-20 ºC to 50 ºC)
Humidity
20% to 85% (No dew condensation)
Radio law division
Self-guided read-write communication facility
Applicable card
ISO 14443 TypeA, FeliCa-based noncontact IC
card, HID iClass
Acquired standard
VCCI class B
Compatible computer
CPU
PC/AT compatible, 1 GHz or more
Memory
128 MB or more
HDD
Free space: 100 MB or more
Monitor
800e 600 pixels, 16-bit color or more
Network
TCP/IP
Application
Microsoft Internet Explorer 6.0 (SP1) or later
Microsoft .NET Framework (SP1) or later
Interface
USB 1.1 or later
Supported Operating Systems
bizhub C652/C652DS/C552/C552DS/C452
Windows 2000 Professional (SP4)
Windows XP Professional Edition (SP2)
Windows Vista Business/Enterprise
12-18
13
Appendix
13.1
Colors
13
Appendix
13.1
Colors
13
Hue, brightness, and saturation
Color has three elements: hue, brightness, and saturation. These are referred to as three attributes of colors
and all colors are created by combinations these elements.
You can adjust the hue, brightness, and saturation in 19 levels.
What is hue?
Everybody has an idea of what "hue" an object has, for example, an apple is red, a lemon is yellow, and the
sky is blue. "Hue" is the tint by which the color of an object is classified as red, yellow, blue, etc.
What is brightness?
"Brightness" is the degree of lightness in a color, as compared with another color, which makes it a light color
or a dark color. For example, when comparing the yellow of a lemon and the yellow of a grapefruit, it is
obvious that the yellow of the lemon is brighter. But what about when comparing the yellow of a lemon and
the red of a bean? Obviously, the yellow of the lemon is brighter. "Brightness" is this degree of lightness that
enables comparison regardless of the hue.
bizhub C652/C652DS/C552/C552DS/C452
13-2
13.1
Colors
13
What is saturation?
What makes the difference between the yellow of a lemon and the yellow of a pear? By saying that the lemon
is a more vivid yellow and the pear is a duller yellow, the difference between the two colors is stated in terms
of "saturation", as opposed to "brightness". As opposed to hue and brightness, "saturation" is the
characteristic that indicates the degree of vividness.
Hue
Brightness
Saturation
bizhub C652/C652DS/C552/C552DS/C452
13-3
13.1
Colors
13
Red, green, and blue
This machine allows you to adjust red, green, and blue in 19 levels.
Red
Green
Bule
bizhub C652/C652DS/C552/C552DS/C452
13-4
13.2
13.2
Image quality
13
Image quality
Contrast, copy density, and sharpness
Contrast:
You can finely adjust an image in between soft/smooth and crisp.
Copy density:
You can finely adjust the shading of an image.
Sharpness:
You can adjust the amount of contours in text and images.
You can adjust the contrast and copy density in 19 levels and the sharpness in 7 levels.
Contrast
Copy Density
Sharpness
bizhub C652/C652DS/C552/C552DS/C452
13-5
13.2
Image quality
13
Color balance (CMYK)
Full-color copy reproduces colors of the original by mixing toners of four colors: yellow, magenta, cyan, and
black. By changing the amount of each of the four toners, adjust the tints in the copy.
You can adjust the color balance in 19 levels.
Yellow
Red
Green
Magenta
Cyan
Bule
Black
bizhub C652/C652DS/C552/C552DS/C452
13-6
13.3
13.3
Glossary
13
Glossary
The following describes the terms used in Copy mode.
Term
Description
ADF
The acronym for automatic 2-sided document feeder, which automatically scans
originals. (ADF = Automatic document feeder)
AE Level Adjustment
Function that adjusts the background of the original. The higher the setting, the
more that the document background is emphasized. (AE = Auto Exposure)
APS
The acronym for Auto Paper Select. (APS = Auto Paper Select)
ATS
Function that automatically switches trays. (ATS=Auto Tray Switch)
Auto Paper
Function that detects the size of the original placed on the original glass or loaded into the ADF, and automatically selects paper of the same size if it is set to
Full Size or selects the paper size appropriate to the specified zoom ratio.
Auto Zoom
Function that automatically selects the appropriate zoom ratio when you place
an original in the ADF or on the original glass, and selects the paper size.
Background Color
Function that copies the original using one of the 18 colors available for the
background color (blank areas).
Background Removal
Function that adjusts the background density of the original with a colored background. Select a background removal method and level to copy the original.
Binding Position
Function that allows you to specify the position of the page margin in one side
of the loaded original. Selecting the appropriate setting prevents the copy from
being printed upside-down when making a 2-sided copy from a 1-sided original
or when making a 1-sided copy from a 2-sided original.
Blue
Function that adjusts the level of blue in the image, for example, if you wish to
emphasize the blue of water or the sky.
Brightness
Function that makes the image either lighter or darker.
Center Staple & Fold
Function that folds the copies in half and staples them together in the center.
Change Tray Settings
Function that copies the original with a paper size not specified in the paper tray
or copies it on paper other than plain paper.
Color
Function that copies the original in specified colors. Using the 2 Color function,
you can copy in two colors: specified color and black.
Color Adjust
Function that adjusts the color copy image quality to match the original image.
Color Balance
Function that adjusts the balance in the concentration for each of cyan (C), magenta (M), yellow (Y) and black (K). You can finely adjust the individual color balance in 19 levels between -3 and +3.
Combine Originals
Function that arranges reduced copies of multiple original pages on a single
copy page. You can select , "2in1", "4in1", or "8in1" depending on the number
of pages to be combined.
Contrast
Function that adjusts the contrast between light and dark.
Copy Density
Function that allows you to finely adjust the copy density in 19 levels between 3 and +3.
Copy Protect
Function that prints hidden text to prevent unauthorized copying. Copying a
copy-protected document repeatedly prints hidden text in all pages more clearly
than the original to prove the user that it is a copied document.
Cover Sheet
Function that attaches a sheet in the specified paper tray as a cover page.
Density
Function that adjusts the density of the print image in nine levels.
Duplex 2nd Side
Function to use when copying on paper that has already been printed on one
side.
Duplex/Combine
Function to specify the scanning side of the original and the printing side of the
paper to be 1-sided or 2-sided.
Edit Color
Function that configures the image according to the objectives of copy editing.
Finishing
Allows you to select how to sort or finish copies when feeding them into the output tray.
bizhub C652/C652DS/C552/C552DS/C452
13-7
13.3
Glossary
13
Term
Description
Finishing Preview
Function that allows you to check the finishing status with a preview image before printing.
Finishing Program
Allows you to select a preset offset or finishing method.
Glossy
Function that improves the glossy level of an image.
Green
Function that adjusts the level of green in the image, for example, if you wish to
emphasize the green of forests and trees.
Group (Access permission)
Function that limits the addresses that can be accessed by each user in order to
assure security.
Group (Copy or Finishing)
Function that prints copies in pages. This function first prints the specified
number of copies of the first page, and then prints the second page in the same
way.
Half-Fold
Function that folds printed paper in half.
Hue
Function that adjusts the hue level to make the image either more reddish or
more bluish.
Manual
Function that enlarges or reduces the loaded original with the zoom ratio specified using the keypad, and copies it on paper.
Minimal
This setting slightly reduces the image of the original and copies it at the center
of the paper.
Mirror Image
Function that produces a copy in the mirror image of the original.
Mixed Original
Function that detects the size of each original page and prints a copy on paper
of the appropriate size when loading originals in different page sizes into the
ADF.
Neg./Pos. Reverse
Function that copies the original with the light- and dark-colored areas or the
colors (gradations) of the image reversed.
Offset
Function that sorts copies.
Original Direction
Function that allows you to configure the orientation of the original that was
placed in the ADF or on the original glass.
Original Type
Function that allows you to select the desired functions according to the original
text or image type and adjust it to obtain better image quality.
Paper
Allows you to configure the type and the size of the paper to be printed on.
Proof Copy
Function that prints a sample copy and stops printing temporarily before printing
a large number of copies. This prevents copy errors from occurring in a large
number of copies.
Punch
Function that punches copies for filing.
Red
Function that adjusts the level of red in the image, for example, if you wish to redden skin tones.
Saturation
That adjusts the degree of vividness of the colors in the image.
Save in User BOX
Function that temporarily saves the job on the hard disk so that it can be recalled
later and used again.
Separate Scan
Function that divides the original into multiple parts for scanning when the
number of original pages exceeds the maximum (100 pages) that can be loaded
into the ADF. You can scan the original and batch-copies it as one copy job. You
can also load the original on the original glass or switch to the ADF during scanning.
Sharpness
Function that emphasizes the edges of text so that it can be read more easily.
This function also enables you to adjust the original image.
Sheet/Cover/Chapter Insert
Allows you to configure editing functions according to your copying requirement.
Sort
Function that prints a document in sets of copies. The second copy set is printed
after all of the first copy set is finished.
Staple
Function that staples copies.
Text Enhancement
Function that allows you to configure the reproduction quality of the text when
copying originals consisting of text that overlaps images such as illustrations or
graphs (text with a background).
bizhub C652/C652DS/C552/C552DS/C452
13-8
13.3
Glossary
13
Term
Description
Transparency Interleave
Function that inserts a blank sheet between transparency films each time a
transparency film is copied. This function prevents transparency films from sticking together.
Tri-Fold
Function that tri-folds printed paper.
Zoom
Function that changes the zoom ratio of the copy.
bizhub C652/C652DS/C552/C552DS/C452
13-9
14
Index
14.1
Index by item
14
Index
14.1
Index by item
Numerics
1st Z-Fold Position Adjustment .................................7-18
2nd Z-Fold Position Adjustment ...............................7-19
A
Access .........................................................................4-8
Accessibility ..............................................................4-12
Account track ..............................................................4-8
Account track settings ..............................................7-37
ADF ..............................................................................2-7
Adjusting gradation ...................................................7-21
Adjusting the center staple position ..........................7-14
Adjusting the half-fold position .................................7-15
Adjusting the punch edge sensor .............................7-17
Adjusting the punch horizontal position ....................7-16
Adjusting the punch resistance loop .........................7-17
Adjusting the punch vertical position ........................7-16
Adjusting the tri-fold positions ..................................7-15
Administrator password ............................................7-49
Administrator security levels .....................................7-50
Administrator settings .................................................7-2
Administrator/machine settings ................................7-29
Advanced preview .....................................................4-19
Application settings ...................................................5-20
Authentication device settings ..................................7-40
Authentication method ..............................................7-40
Authentication unit ..............................................2-2, 2-5
Authentication unit (biometric type)
............................................................10-2, 12-16, 12-17
Authentication unit (IC card type) ..................11-2, 12-17
Automatic duplex unit .......................................2-7, 12-7
B
Background color ......................................................5-31
Basic tab ...................................................................2-16
Biometric type ...........................................................10-2
Blank page print settings ..........................................7-26
Blue ...........................................................................13-4
Book copy .................................................................5-33
Book copy/repeat ......................................................5-33
Booklet ......................................................................5-40
Booklet original .........................................................5-36
Brightness .................................................................13-2
Brightness adjustment dial ........................................2-14
Bypass tray .................................................................2-7
Bypass tray door .........................................................2-7
C
C ................................................................................4-17
Centering ...................................................................7-13
bizhub C652/C652DS/C552/C552DS/C452
14
Centering (duplex 2nd side) ......................................7-13
Changing E-mail addresses ......................................6-14
Changing icons ..........................................................6-15
Changing passwords .................................................6-13
Charger-cleaning tool ................................................2-11
Checking comsumables ..............................................8-8
Checking job settings ................................................2-16
Checking job settings. ...............................................5-64
Checking the total number of pages printed .............8-11
Cleaning procedure ...................................................8-12
CMYK ........................................................................13-6
Color ............................................................................5-4
Color adjustment .......................................................5-31
Color balance ............................................................13-6
Color registration adjustment ....................................7-20
Colors ........................................................................13-2
Configuring the basic settings .....................................5-3
Contrast .....................................................................13-5
Control panel .................................. 2-7, 2-14, 4-2, 8-13
Copier settings ................................................. 6-8, 7-43
Copy density .............................................................13-5
Copy function ..............................................................5-2
Copy protection .........................................................5-48
Copying .......................................................................4-5
Copying mixed originals ............................................5-16
Cover sheet ...............................................................5-22
Coverage rate ............................................................8-10
Custom display settings ..............................................6-6
Custom size .................................................................5-6
D
Data indicator ............................................................2-14
Date/time ...................................................................5-44
Date/time settings .......................................................7-5
Daylight saving time ....................................................7-6
Default bypass paper type setting ............................7-27
Document pad ...........................................................8-14
Driver password encryption setting ...........................7-57
Duplex/Combine ..........................................................5-8
E
Editing colors .............................................................5-29
Editing pages .............................................................5-21
Eject assist lever ........................................................2-25
Electrostatic charger wire ..........................................9-12
Enhanced security mode ...........................................7-54
Enlarge Display ..........................................................4-14
Erasing .......................................................................5-41
Erasing frames ...........................................................5-41
14-2
14.1
Index by item
Erasing non-image areas ..........................................5-42
Expert adjustment .......................................................7-9
External server settings .............................................7-39
F
Fax kit ..................................................................2-2, 2-6
Fax multi line ...............................................................2-2
Fax settings ...............................................................7-46
Fax/Scan .....................................................................4-5
Fax/scan settings ......................................................6-11
Filter .............................................................................2-9
Finisher ......................... 2-2, 2-3, 2-6, 2-18, 2-23, 12-9
Finisher connector .......................................................2-9
Finishing ....................................................................5-10
Folding and binding ...................................................5-10
Front door ..............................................2-18, 2-21, 2-24
Function keys ............................................................2-14
Function management settings .................................7-56
Functions/settings display area ................................2-16
Fusing unit .................................................................2-11
Fusing unit cover lever ..............................................2-11
G
General settings ........................................................7-32
Green .........................................................................13-4
Grouping ...................................................................5-10
Guidance ...................................................................4-15
Guide lever ............................................2-18, 2-21, 2-24
H
HDD settings .............................................................7-55
Header/footer ............................................................5-53
Hide Personal Information (MIB) ...............................7-52
Horizontal transport unit cover ........................2-18, 2-24
Housing .....................................................................8-14
Hue ............................................................................13-2
I
IC card type ...............................................................11-2
Icon/shortcut key display area ..................................2-16
Icons ..........................................................................9-10
Image adjustment ......................................................5-39
Image controller ..................................................2-2, 2-5
Image quality .............................................................13-5
Image Repeat ............................................................5-34
Imaging unit ...............................................................2-11
Imaging unit release lever .........................................2-11
Inserting images ........................................................5-24
Inserting sheets .........................................................5-23
Inside of the main body .............................................2-11
Interleaving OHP transparencies ...............................5-21
Internal controller port .................................................2-9
Interrupt .......................................................................4-4
J
Jack for connecting a telephone (TEL PORT1) ...........2-9
Jack for connecting a telephone (TEL PORT2) ...........2-9
Jam removal cover ....................................................2-26
bizhub C652/C652DS/C552/C552DS/C452
14
Jam removal dial ............................................ 2-11, 2-18
Job list .......................................................................2-16
Job Separator ................. 2-3, 2-6, 12-12, 12-15, 12-16
Job separator cover ..................................................2-20
Job Separator JS-504 ...............................................2-25
Job separator JS-602 ................................................2-20
Job Separator JS-603 ...............................................2-23
K
Keypad ......................................................................2-14
L
Large capacity unit ......................... 2-2, 2-5, 2-26, 12-8
Lateral guide ................................................................2-7
Leading edge adjustment ..........................................7-13
Leading edge adjustment (duplex side 2) .................7-13
Left panel ........................................................ 2-16, 5-61
Left-side cover .............................................................2-7
Left-side cover release levert ......................................2-7
License settings .........................................................7-58
Limiting access to destinations .................................7-39
List/counter ...............................................................7-22
Listing jobs ................................................................5-62
Loading paper .............................................................8-3
Loading paper into the bypass tray .............................8-5
Loading paper into the LCT .........................................8-7
Loading paper into trays 1 and 2 ................................8-3
Loading paper into trays 3 and 4 ................................8-4
Local interface kit ............................................... 2-2, 2-6
Lower front door ..........................................................2-7
Lower right-side door ..................................................2-7
Lower right-side door release lever .............................2-8
Lower Tray .................................................................2-22
Lower tray paper guide .............................................2-22
M
Machine specifications ..............................................12-4
Main power indicator .................................................2-14
Main power switch ......................................................2-7
Maintenance ................................................................8-2
Media adjustment ......................................................7-14
Message display area ................................................2-16
Meter count ...............................................................8-10
Mirror image ..............................................................5-30
Mode Memory .............................................................4-7
Mount kit ............................................................. 2-2, 2-5
N
Negative-positive reversal .........................................5-29
Network connector
(10Base-T/100BaseTX/1000Base-T) ...........................2-9
Network settings .......................................................7-42
O
Offsetting ...................................................................5-10
OpenAPI Authentication Management Settings ........7-59
Options ............................................................. 2-2, 12-8
Original glass ........................................ 2-11, 8-12, 8-13
14-3
14.1
Index by item
Original glass cleaner ................................................2-11
Original output tray ......................................................2-7
Original scales ...........................................................2-11
Original setting ..........................................................5-15
Original tray .................................................................2-7
Output belt ................................................................2-18
Output settings ............................................................7-4
Output tray ....................................... 2-2, 2-5, 2-7, 2-18
Output tray 1 .........................................2-18, 2-24, 2-25
Output tray 2 .........................................2-18, 2-24, 2-25
Output tray switch .....................................................2-18
Outside of the main body (front) .................................2-7
Outside of the main body (rear) ...................................2-9
Overlay ......................................................................5-55
Overlaying registered images ....................................5-56
Ozone filter ..................................................................2-9
P
Page margin ..............................................................5-37
Page number .............................................................5-45
Page number print position settings .........................7-28
Paper .........................................................5-5, 8-2, 12-2
Paper capacities ........................................................12-2
Paper types ...............................................................12-2
Paper-empty indicator ......................................2-7, 2-26
Password Copy .........................................................5-50
Placing originals ..........................................................3-4
Post Inserter ............................... 2-3, 2-22, 5-12, 12-13
Post inserter control panel ..............................2-22, 5-12
Poster mode ..............................................................5-35
Power cord ..................................................................2-9
Power Save ...............................................................4-11
Power save settings ....................................................7-3
Power switch for dehumidifying heater .......................2-9
Print head ..................................................................9-13
Print head glass cleaning tool ...................................2-11
Print without authentication ......................................7-38
Printer settings ................................................6-12, 7-45
Printing counter list ...................................................7-38
Program jobs .............................................................5-27
Proof copy .................................................................4-18
Punch kit .................................... 2-2, 2-18, 2-23, 12-11
Punch kit PK-516 ......................................................2-18
Punch Kit PK-517 ......................................................2-23
Punch scrap box ...................................2-19, 2-21, 2-24
Punch Unit Size Detect Sensor .................................7-19
Punching ...................................................................5-10
Q
Quality/density ..........................................................5-18
Quick Copy tab .........................................................2-16
R
Red ............................................................................13-4
Register Authentication Information ..........................6-16
Registering one-touch destinations or
User Boxes ................................................................7-30
bizhub C652/C652DS/C552/C552DS/C452
14
Release lever .............................................................2-26
Replacement message ................................................8-8
Replenishment message .............................................8-2
Reset ...........................................................................4-4
Reset settings ............................................................7-23
Restricting user accesses ...........................................7-8
Reverse automatic document feeder ........................12-7
RS-232C port ..............................................................2-9
S
Saddle stitcher ..................... 2-2, 2-3, 2-6, 2-18, 12-10
Saddle stitcher SD-508 .............................................2-18
Saddle Stitcher SD-509 .............................................2-23
Saturation ..................................................................13-2
Saving in User Boxes ................................................5-60
Scan to authorized folder settings ............................7-41
Scan to home settings ...............................................7-41
Security details ..........................................................7-51
Security kit .......................................................... 2-2, 2-6
Security settings ........................................................7-49
Separate scan ...........................................................5-13
Separating chapters ..................................................5-26
Service call ..................................................................9-2
Settings common to user and account track
authentication ............................................................7-41
Sharpness ..................................................................13-5
Skip job operation settings ........................................7-26
Sorting .......................................................................5-10
Specifications ............................................................12-2
Stamp ........................................................................5-47
Stamp repetition ........................................................5-51
Stamp settings ............................................... 7-25, 7-57
Stamp unit .......................................................... 2-3, 2-6
Stamp/composition ...................................................5-43
Staple cartridge .........................................................2-25
Staple holder .............................................................2-24
Staple replacement door ...........................................2-18
Stapler .......................................................................2-24
Stapling .....................................................................5-10
Start .............................................................................4-4
Status indicator ...........................................................2-7
Stop .............................................................................4-4
Stylus pen ..................................................................2-14
Sub power switch ............................................. 2-7, 2-14
System connection ....................................................7-47
System settings .................................................. 6-3, 7-3
T
Take-up roller ............................................................8-13
Telephone jack 1 (LINE PORT1) ..................................2-9
Telephone jack 2 (LINE PORT2) ..................................2-9
Toner cartridges ........................................................2-11
Toner supply indicators .............................................2-16
Total counter ...............................................................2-7
Touch panel .................................................... 2-14, 2-16
Touch pen ..................................................................2-14
Tray 1 ...........................................................................2-7
14-4
14.1
Index by item
14
Tray 2 ..........................................................................2-7
Tray 3 ..........................................................................2-7
Tray 4 ..........................................................................2-7
Tray extension ...........................................................2-25
Troubleshooting ..........................................................9-2
Troubleshooting table .................................................9-4
Turning off automatic rotation ...................................5-14
U
Upper door ................................................................2-26
Upper front door ..........................................................2-7
Upper right-side door ..................................................2-7
Upper right-side door release lever .............................2-8
Upper Tray ................................................................2-22
Upper Tray paper guide ............................................2-22
Upper unit release lever ............................................2-22
USB port (type A) USB 2.0/1.1 ............................2-7, 2-9
USB port (type B) USB 2.0/1.1 ....................................2-9
User authentication .....................................................4-8
User authentication settings .....................................7-34
User authentication/account track ............................7-31
User Box ......................................................................4-5
User Box administrator setting .................................7-49
User Box settings ......................................................7-24
User settings ...............................................................6-2
Utility/Counter .............................................................4-6
V
Video interface kit ........................................................2-2
W
Waste toner box ........................................................2-11
Watermark .................................................................5-54
Weekly timer setting ....................................................7-7
Wide paper ..................................................................5-6
Working table ......................................................2-2, 2-5
Z
Z folding unit .................................................2-21, 12-12
Z-folded original ........................................................5-17
Zoom .................................................................5-7, 5-59
bizhub C652/C652DS/C552/C552DS/C452
14-5
14.2
14.2
Index by button
14
Index by button
Numerics
1-Sided > 1-Sided .......................................................5-8
1-Sided > 2-Sided .......................................................5-8
1st Z-Fold Position Adjustment .................................7-18
2 Color .........................................................................5-4
2/4/8 Repeat ..............................................................5-35
2in1 ..............................................................................5-9
2nd Z-Fold Position Adjustment ...............................7-19
2-Sided > 1-Sided .......................................................5-8
2-Sided > 2-Sided .......................................................5-8
4in1/8in1 ......................................................................5-9
A
Access .........................................................................4-8
Accessibility ..............................................................4-12
Account Name ...................................................4-9, 7-35
Account Track ...........................................................7-32
Account Track Counter .............................................7-38
Account Track Input Method ....................................7-32
Account Track Registration .......................................7-37
Account Track Settings .............................................7-37
Administrative Settings .............................................7-34
Administrator Password ............................................7-49
Administrator Registration .........................................7-29
Administrator Security Levels ...................................7-50
Administrator Settings .........................................4-6, 7-2
Administrator/Machine Settings ................................7-29
AE Level Adjustment ...........................................6-3, 7-9
All Jobs ......................................................................5-63
Application ................................................................5-20
Apply Stamps ............................................................7-57
Auth.-info.registrieren ................................................7-35
Authentication Device Settings .................................7-40
Auto .............................................................................5-7
Auto Booklet ON when Fold & Staple .........................6-8
Auto Color ...................................................................5-4
Auto Color Level Adjust. ..............................................6-3
Auto Detect ...............................................................5-34
Auto Paper Select for Small Original ...........................6-4
Auto Prefix/Suffix setting ...........................................7-47
Auto Reset .................................................................7-23
Auto Reset Confirmation ...........................................4-13
Auto Rotate OFF .......................................................5-14
Auto Sort/Group Selection ..........................................6-8
Auto Tray Selection Settings .......................................6-3
Auto Tray Switch ON/OFF ...........................................6-3
Auto Zoom (ADF) ...............................................6-8, 7-43
Auto Zoom (Platen) ............................................6-8, 7-43
Auto Zoom for Combine/Booklet ................................6-8
Automatic Image Rotation .................................6-9, 7-43
B
Back (Blank) ..............................................................5-22
Back (Copy) ...............................................................5-22
bizhub C652/C652DS/C552/C552DS/C452
Background Color .....................................................5-31
Background Removal ................................................5-19
Banner Printing ............................................................4-6
Basic ............................................................................5-3
Binding Position ..................................... 5-8, 5-15, 5-34
Bio Authentication .....................................................7-40
Black ............................................................................5-4
Blank ..........................................................................5-24
Blank Page Print Settings ................................. 6-4, 7-26
Blue ...........................................................................5-32
Book Copy .................................................................5-33
Book Copy/Repeat ....................................................5-33
Book Spread ..............................................................5-33
Booklet ......................................................................5-40
Booklet Original .........................................................5-36
Bottom .......................................................................5-41
Brightness .................................................................5-32
Bypass Tray .................................................................5-5
C
C ................................................................................4-17
Card Authentication ...................................................7-40
Card Copy .................................................................5-59
Card Shot Settings ......................................................6-9
Cellular Phone/PDA Setting ......................................7-48
Center Erase ..............................................................5-34
Center Staple & Fold .................................................5-40
Center Staple Position ...............................................7-14
Center Zoom .............................................................5-39
Centering ........................................................ 5-39, 7-13
Centering (Duplex 2nd Side) ......................................7-13
Change E-Mail Address .............................................6-14
Change Icon ..............................................................6-15
Change Password .....................................................6-13
Change Setting ..........................................................4-20
Change Size ................................................................5-6
Change Tray Settings ..................................................5-5
Chapter Paper ...........................................................5-26
Chapters ....................................................................5-26
Check Consumable Life ..............................................4-6
Check Details ............................................................5-61
Check Job ...................................................... 5-61, 5-64
Check Job Set. ..........................................................5-63
Check Program Settings .............................................4-7
Check/Change Temporarily .......................................5-53
Color ................................................................. 5-4, 5-55
Color Adjustment .......................................................5-31
Color Balance ............................................................5-32
Color Registration Adjust ............................... 7-11, 7-20
Color Selection Settings ..............................................6-6
Composition ..............................................................5-56
Confidential Document Access Method ....................7-52
Consumables Replace/Processing Procedure ..........4-16
Contrast .....................................................................5-32
14-6
14.2
Index by button
Copied Paper ............................................................5-19
Copier Settings ..........................................6-6, 6-8, 7-43
Copy ..................................................................4-5, 5-23
Copy Card Settings ...................................................7-43
Copy Density .............................................................5-32
Copy Guard ...............................................................5-49
Copy Insert ................................................................5-26
Copy Program Lock Settings ......................................7-8
Copy Protect .............................................................5-48
Copy Screen ................................................................6-6
Counter Details ................................................7-36, 7-38
Cover Sheet .....................................................5-22, 5-40
Coverage Rate ..........................................................8-10
Current Jobs ..............................................................5-63
Custom Display Settings .............................................6-6
Custom Size ................................................................5-6
D
Date Format ..............................................................5-44
Date Settings ...............................................................7-7
Date/Time ......................... 5-44, 5-48, 5-50, 5-51, 5-52
Date/Time Settings ......................................................7-5
Daylight Saving Time ...................................................7-6
Default Bypass Paper Type Setting ..........................7-27
Default Copy Settings .................................................6-8
Default Enlarge Display Settings .................................6-8
Default Function Permission .....................................7-34
Default Operation Selection ......................................7-34
Default Tab ..................................................................6-6
Default Tab Density Settings .......................................6-6
Delete ..............................................................5-61, 5-63
Delete Registered Stamp ..........................................7-57
Delete Saved Copy Program .......................................7-8
Deleted Jobs .............................................................5-63
Density ............................................................5-19, 5-55
Density Adjustment ...................................................7-10
Despeckle ..................................................................5-15
Detail .........................................................................5-63
Detail Settings ............................ 5-48, 5-50, 5-51, 5-52
Detection While Feeding Setting ...............................7-11
Device Information ......................................................4-6
Display Activity Log ...................................................7-52
Document Name .......................................................5-60
Dot Matrix Original ....................................................5-19
Driver Password Encryption Setting .........................7-57
Duplex/Combine .........................................................5-8
E
Edit Color ..................................................................5-29
Edit Name ....................................................................4-7
E-Mail Address ..........................................................7-34
Enhanced Security Mode ..........................................7-54
Enlarge Display ..........................................................4-14
Enlarge Display Mode Confirmation ..........................4-13
Enlargement Rotation ..................................................6-8
Enter Power Save Mode .............................................7-3
bizhub C652/C652DS/C552/C552DS/C452
14
Erase ..........................................................................5-41
Erase Adjustment ......................................................7-12
Expert Adjustment .......................................................7-9
External Server Settings ............................................7-39
F
FAX Active Screen .......................................................6-6
Fax Settings ...............................................................7-46
Fax TX Settings .........................................................7-25
Fax/Scan .....................................................................4-5
Fax/Scan Settings .....................................................6-11
Finished Jobs ............................................................5-63
Finisher Adjustment ...................................................7-10
Finishing ....................................................................5-10
Finishing Program .......................................................6-9
Fixed Zoom .................................................................5-7
Fold/Bind ...................................................................5-11
Frame ........................................................................5-41
Frame Erase ................................................... 5-34, 5-41
Front (Blank) ..............................................................5-22
Front (Copy) ...............................................................5-22
Front and Back Cover ...............................................5-33
Front Cover ................................................................5-33
Full Color .....................................................................5-4
Full Size ............................................................ 5-7, 5-39
Function .....................................................................4-15
Function Management Settings ................................7-56
Function Map ............................................................4-15
Function Permission ..................................................7-35
G
General Settings ............................................. 7-32, 7-40
Get Request Code .....................................................7-58
Glossy ........................................................................5-19
Gradation Adjustment .................................... 7-11, 7-21
Green .........................................................................5-32
Group .........................................................................5-10
Guidance ...................................................................4-15
H
Half-Fold ....................................................................5-40
Half-Fold Position ......................................................7-15
Half-Fold Specification ................................................6-9
Half-Fold/Tri-Fold Specification ..................................6-9
HDD Settings .............................................................7-55
Header/Footer ...........................................................5-53
Header/Footer Settings .............................................7-25
Hide Personal Information .........................................7-52
Hide Personal Information (MIB) ...............................7-52
Hue ............................................................................5-32
I
Icon ............................................................................7-35
ID & Print Operation Settings ....................................7-34
ID & Print Settings .....................................................7-34
Image Adjust ..............................................................5-39
Image Repeat ............................................................5-34
14-7
14.2
Index by button
14
Image Shift ................................................................5-38
Image Size .................................................................5-35
Image Stabilization ....................................................7-10
Image Stabilization Only ............................................7-10
Image Stabilization Setting ........................................7-11
Increase Priority ........................................................5-63
Initialize ......................................................................7-52
Input Machine Address .............................................7-29
Insert Image ...............................................................5-24
Insert Paper ...............................................................5-23
Insert Sheet ...............................................................5-23
Insert Sheet Setting ...................................................5-46
Install License ............................................................7-58
Interleave Paper ........................................................5-21
Interrupt .......................................................................4-4
Mirror Image ..............................................................5-30
Mixed Original ...........................................................5-15
Mode Memory .............................................................4-7
J
Offset .........................................................................5-11
OHP Interleave ..........................................................5-21
ON (External Server) ..................................................7-32
ON (MFP) ...................................................................7-32
One-Touch/User Box Registration ................... 4-6, 7-30
OpenAPI Authentication Management Settings ........7-59
OpenAPI settings .......................................................7-47
Original Setting ..........................................................5-15
Original Type .............................................................5-18
Other ............................................................... 5-48, 5-52
Other Functions .........................................................4-15
Output Permission .......................................... 7-35, 7-37
Output Settings .................................................. 6-3, 7-4
Output Tray Settings ...................................................7-4
Overlay ......................................................................5-55
Job Details ................................................................5-61
Job History ................................................................5-63
Job History Thumbnail Display .................................7-52
Job List ............................................................5-61, 5-62
Job Log Settings .......................................................7-52
Job Reset ..................................................................7-23
K
Key Repeat Start/Interval Time .................................4-13
L
Language Selection .....................................................6-3
Layout ........................................................................5-59
LCT ..............................................................................5-5
Leading Edge Adjustment .........................................7-13
Leading Edge Adjustment (Duplex Side 2) ................7-13
Left ............................................................................5-41
Left Bind ....................................................................5-40
Left Panel Display Default ...........................................6-6
License Settings ........................................................7-58
Limiting Access to Destinations ................................7-39
Line Detection ...........................................................7-11
List/Counter ...............................................................7-22
Login ............................................................................4-9
Logout Confirmation Screen Display Setting ............7-41
Low Power ..................................................................7-3
Low Power Mode Settings ..........................................7-3
M
Management List .......................................................7-22
Manual .........................................................................5-7
Manual Destination Input ..........................................7-52
Map ...........................................................................5-18
Margin Position .........................................................5-38
Max. Allowance Set .........................................7-35, 7-37
Measurement Unit Settings .........................................6-3
Media Adjustment .....................................................7-14
Message Display Time ..............................................4-13
Meter Count ..............................................................8-10
Minimal ........................................................................5-7
bizhub C652/C652DS/C552/C552DS/C452
N
Name and Function of Parts ......................................4-15
Neg./Pos. Reverse .....................................................5-29
Network Function Usage Settings .............................7-56
Network Settings .......................................................7-42
No Matching Paper in Tray Setting .............................6-3
None ..........................................................................5-41
Non-Image Area Erase ..............................................5-42
Non-Image Area Erase Operation Settings ...............7-12
Number of User Counters Assigned .........................7-33
O
P
P --- ...................................................... 5-23, 5-25, 5-26
Page Margin ..............................................................5-37
Page Number ............................................................5-45
Page Number Print Position ............................. 6-4, 7-28
Page Number Type ....................................................5-45
Pages .......................................... 5-44, 5-47, 5-55, 5-57
Paper ................................................................ 5-5, 5-22
Paper Separation Adjustment ...................................7-11
Paper Size .................................................................5-36
Paper Size/Type Counter ..........................................7-22
Paper Tray Settings .....................................................6-3
Password .......................................................... 4-9, 7-34
Password Copy .........................................................5-50
Password for Non- Business Hours ............................7-7
Password Rules .........................................................7-51
Pause .............................................................. 7-35, 7-38
Photo .........................................................................5-18
Position ........................................................... 5-49, 5-52
Position Setting .........................................................5-12
Post Inserter ..................................................... 2-3, 5-12
Post inserter control panel ........................................5-12
Poster Mode ..............................................................5-35
Power Save ...............................................................4-11
Power Save Key ..........................................................7-3
14-8
14.2
Index by button
Power Save Settings ...........................................6-3, 7-3
Preset Stamp ...................................................5-48, 5-52
Print ...........................................................................5-62
Print Counter List ......................................................7-38
Print Data Capture .....................................................7-52
Print Jobs During Copy Operation ....................6-9, 7-43
Print Lists ....................................................................6-3
Print Position .........................................5-44, 5-46, 5-47
Print without Authentication ......................................7-38
Print/Fax Output Settings ............................................7-4
Printer Adjustment .......................................................7-9
Printer Information .....................................................7-48
Printer Settings ........................................6-12, 7-2, 7-45
Prior Detection Setting ..............................................7-11
Program Jobs ............................................................5-27
Prohibited Functions When Authentication Error ......7-51
Proof Copy ................................................................4-18
Public User Access ...........................................4-9, 7-32
Punch ........................................................................5-11
Punch Edge Sensor Adjustment ...............................7-17
Punch Horizontal Position Adjustment ......................7-16
Punch Regist Loop Size Adjustment .........................7-17
Punch Vertical Position Adjustment ..........................7-16
Q
Quality/Density ..........................................................5-18
Quick Settings 1 ..........................................................6-6
Quick Settings 2 ..........................................................6-6
Quick Settings 3 ..........................................................6-6
Quick Settings 4 ..........................................................6-6
R
Recall Header/Footer ................................................5-53
Recall Overlay Image ................................................5-57
Receive ......................................................................5-62
Red ............................................................................5-32
Register Authentication Information ..........................6-16
Register Overlay Image .............................................5-57
Register Program ........................................................4-7
Registered Overlay ....................................................5-56
Registered Stamp ...........................................5-48, 5-52
Release Held Job ......................................................5-63
Reset .................................................................4-4, 5-53
Reset All Counters ...........................................7-36, 7-38
Reset Settings ...........................................................7-23
Restrict Access to Job Settings ..................................7-8
Restrict Fax TX ..........................................................7-52
Restrict Operation .......................................................7-8
Restrict User Access ...................................................7-8
Right ..........................................................................5-41
Right Bind ..................................................................5-40
Rotate Image .............................................................4-20
S
Saturation ..................................................................5-32
Save ..........................................................................5-62
Save & Print ...............................................................5-60
bizhub C652/C652DS/C552/C552DS/C452
14
Save in User Box .......................................................5-60
Scan to Authorized Folder Settings ...........................7-41
Scan to Home Settings .............................................7-41
Scan/Fax Settings .......................................................6-6
Search by Operation .................................................4-15
Search Option Settings ...............................................6-7
Secure Print Only .......................................................7-52
Security Details ..........................................................7-51
Security Settings .......................................................7-49
Select Color ...............................................................5-31
Select Keyboard ..........................................................6-4
Select Time for Power Save ........................................7-7
Select Tray for Insert Sheet .............................. 6-8, 7-43
Send ..........................................................................5-62
Separate Scan ...........................................................5-13
Separate Scan Output Method ...................................6-8
Separation .................................................................5-33
Server Name ................................................................4-9
Service/Admin. Information .......................................4-15
Set Range ..................................................................5-35
Sharpness ..................................................................5-32
Sheet/Cover/ Chapter Insert .....................................5-21
Shift Output Each Job .................................................7-4
Shortcut Key 1 .............................................................6-6
Shortcut Key 2 .............................................................6-6
Single Color .................................................................5-4
Single Color > 2 Color Output Management .............7-41
Skip Job Operation Settings .....................................7-26
Sleep ............................................................................7-3
Sleep Mode Settings ...................................................7-3
Sort ............................................. 5-10, 5-23, 5-25, 5-26
Sound Setting ............................................................4-13
Specify Default Tray when APS Off .................. 6-8, 7-43
Stamp ........................................................................5-47
Stamp Repeat ............................................................5-51
Stamp Settings ............................................... 7-25, 7-57
Stamp Type/Preset Stamps ......................................5-47
Stamp/Composition ..................................................5-43
Staple ........................................................................5-11
Start .............................................................................4-4
Starting Chapter Number ..........................................5-45
Starting Page Number ...............................................5-45
Stop .............................................................................4-4
Store ............................................................................5-6
Synchronize User Authentication &
Account Track ...........................................................7-33
System Auto Reset ....................................................7-23
System Auto Reset Confirmation ..............................4-13
System Connection ...................................................7-47
System Settings ................................................. 6-3, 7-3
T
Text ............................................................................5-18
Text Color ....................................................... 5-47, 5-54
Text Details ..................................................... 5-44, 5-46
Text Enhancement .....................................................5-19
14-9
14.2
Index by button
14
Text Size ....................................................................5-47
Text/Photo .................................................................5-18
Ticket Hold Time Setting ...........................................7-33
Time Format ..............................................................5-44
Time Settings ..............................................................7-7
Time Zone ...................................................................7-5
Top ............................................................................5-41
Touch Panel Adjustment ...........................................4-12
Trail Edge Adjust .......................................................7-11
Transparency .............................................................5-21
Tray 1 ..........................................................................5-5
Tray 2 ..........................................................................5-5
Tray 3 ..........................................................................5-5
Tray 4 ..........................................................................5-5
Tri-Fold Position Adjustment .....................................7-15
Tri-Fold Print Side .............................................6-8, 7-43
U
User Authentication ...................................................7-32
User Authentication Settings .....................................7-34
User Authentication/Account Track ..........................7-31
User Box ............................................................4-5, 5-60
User Box Administrator Setting .................................7-49
User Box Settings .............................................6-6, 7-24
User Counter .............................................................7-36
User Name ........................................................4-9, 7-34
User Name List ..................................................4-9, 7-34
User Preset Zoom .......................................................5-7
User Registration .......................................................7-34
User Settings .......................................................4-6, 6-2
User/Account Common Setting ................................7-41
Utility/Counter .............................................................4-6
V
View Finishing ...........................................................4-20
View Pages ................................................................4-20
View Status ...............................................................4-20
W
Watermark .................................................................5-54
Watermark Type ........................................................5-54
Weekly Timer ON/OFF Settings ..................................7-7
Weekly Timer Setting ..................................................7-7
When # of Jobs Reach Maximum .............................7-33
When AMS Direction is Incorrect ................................6-8
Wide Paper ..................................................................5-6
With Margin ...............................................................5-34
Without Margin ..........................................................5-34
X
X/Y ...............................................................................5-6
Z
Z-Folded Original ......................................................5-15
Zoom .......................................................4-19, 5-7, 5-36
bizhub C652/C652DS/C552/C552DS/C452
14-10
http://konicaminolta.com
Copyright
A1DM-9585CO-00
2009
2009.11