Sharp AR-M230 Series Setup guide

!!install_ar230270.book
1 ページ 2004年2月19日 木曜日 午後1時17分
MODEL
AR-M236
AR-M237
AR-M276
AR-M277
DIGITAL MULTIFUNCTIONAL
SYSTEM
SOFTWARE SETUP GUIDE
Page
• INTRODUCTION
Back cover
• SOFTWARE FOR THE SHARP
AR-M230/M270 SERIES
2
• BEFORE INSTALLATION
2
• INSTALLING THE SOFTWARE
3
• CONNECTING TO A COMPUTER 12
• CONFIGURING THE PRINTER
DRIVER
13
• HOW TO USE THE ONLINE
MANUAL
14
• TROUBLESHOOTING
15
!!install_ar230270.book
2 ページ 2004年2月19日 木曜日 午後1時17分
INTRODUCTION
This manual explains how to install and configure the software that is required for the printer function
of the machine. The procedure for viewing the online manual is also explained.
Note
• The screen images in this manual are mainly for Windows® XP. With other versions of
Windows®, some screen images may be different from those in this manual.
• The explanations in this manual are based on the North American version of the software.
Versions for other countries and regions may vary slightly from the North American version.
• Where "AR-XXXX" appears in this manual, please substitute the name of your model for "XXXX".
For the name of your model, see "PART NAMES AND FUNCTIONS" in the operation manual for
copier.
• This manual refers to the "SHARP Digital Multifunctional System AR-M230/M270 Series
Software CD-ROM" simply as "CD-ROM".
Trademark acknowledgments
• Microsoft® Windows® operating system is a trademark or copyright of Microsoft Corporation in the
U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, and Windows®
XP are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries.
• Acrobat® Reader Copyright© 1987- 2002 Adobe Systems Incorporated. All rights reserved. Adobe,
the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• All other trademarks and copyrights are the property of their respective owners.
SOFTWARE LICENSE
The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all
or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by the
terms of the SOFTWARE LICENSE.
The display screens, messages, and key names shown in the manual may differ from those on the actual
machine due to product improvements and modifications.
!!install_ar230270.book
1 ページ 2004年2月19日 木曜日 午後1時17分
CONTENTS
SOFTWARE FOR THE SHARP AR-M230/M270 SERIES.................................................... 2
BEFORE INSTALLATION ..................................................................................................... 2
● HARDWARE AND SOFTWARE REQUIREMENTS ................................................................... 2
● INSTALLATION ENVIRONMENT AND INSTALLATION PROCEDURE.................................... 2
INSTALLING THE SOFTWARE ............................................................................................ 3
● STANDARD INSTALLATION (USB only) ................................................................................... 3
● CUSTOM INSTALLATION.......................................................................................................... 5
● INSTALLING THE PC-FAX DRIVER ........................................................................................ 11
CONNECTING TO A COMPUTER ...................................................................................... 12
● CONNECTING A USB CABLE ................................................................................................. 12
● CONNECTING A PARALLEL CABLE ...................................................................................... 12
CONFIGURING THE PRINTER DRIVER ............................................................................ 13
HOW TO USE THE ONLINE MANUAL............................................................................... 14
TROUBLESHOOTING......................................................................................................... 15
1
!!install_ar230270.book
2 ページ 2004年2月19日 木曜日 午後1時17分
SOFTWARE FOR THE SHARP
AR-M230/M270 SERIES
The CD-ROM that accompanies the machine contains the following software:
• Printer driver
The printer driver enables you to use the printer function of the machine.
• PC-FAX driver
The PC-FAX driver lets you easily send faxes from your computer through the machine to another
fax machine (when the facsimile expansion kit is installed).
* To use the PC-FAX driver, Internet Explorer 4.0 or later must be installed in your computer.
• Acrobat Reader 5.0
Software that allows you to view the online printer manual on your computer.
BEFORE INSTALLATION
HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements before installing the software.
IBM PC/AT or compatible computer equipped with a USB 2.0/1.1*1 or
bi-directional parallel interface (IEEE 1284)
Operating system
Windows 95*2, Windows 98, Windows Me,
Windows NT Workstation 4.0 (Service Pack 5 or later)*3,
Windows 2000 Professional*3, Windows XP Professional*3,
Windows XP Home Edition*3
Other hardware requirements An environment that allows any of the above operating systems to fully operate
Computer type
*1 Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or
Windows XP Home Edition preinstalled models equipped with a USB interface as standard.
*2 If you are installing the PC-FAX driver, a system file must be updated before the driver can be installed. For
more information, click the "Display Readme" button in the Software Selection window of the installer. (p. 11)
*3 Administrator's rights are required to install the software using the installer.
INSTALLATION ENVIRONMENT AND INSTALLATION
PROCEDURE
Follow the appropriate installation procedure for your operating system and type of cable as indicated below.
Operating system
Cable
Windows 98/Me/2000/XP
Windows XP
Windows 98/Me/2000
Windows 95/98/Me/NT
4.0/2000
USB*
USB*/Parallel
USB*
Parallel
Procedure to follow
STANDARD INSTALLATION (USB only) (p. 3)
Installation in Windows XP (USB/Parallel cable) (p. 5)
Installation in Windows 98/Me/2000 (USB cable) (p. 7)
Installation in Windows 95/98/Me/NT 4.0/2000 (Parallel cable) (p. 9)
* If the machine is connected by a USB cable, it is recommended that you use the standard installation.
2
!!install_ar230270.book
3 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
Note
If an error message appears, follow the on-screen instructions to solve the problem. After the
problem is solved, the installation procedure will continue. Depending on the problem, you may
have to click the "Cancel" button to exit the installer. In this case, reinstall the software from the
beginning after solving the problem.
STANDARD INSTALLATION (USB only)
The procedure for a standard installation of the software is explained below. If the machine is
connected by a USB cable, it is recommended that you use the standard installation.
Note
1
The standard installation can only be used when the machine is connected by a USB cable. If the
machine is connected by a parallel cable, use the custom installation procedure (p. 5).
The USB cable must not be connected
to the machine. Make sure that the
cable is not connected before
proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click the
"Cancel" button to close the window and
disconnect the cable.
Note
6
Read the message in the "Welcome"
window and then click the "Next" button.
7
Click the "Standard" button.
Follow the on-screen instructions.
The cable will be connected in step 9.
2
Insert the CD-ROM into your computer's
CD-ROM drive.
3
Click the "start" button, click "My
Computer" ( ), and then double-click
the CD-ROM icon ( ).
In Windows 98/Me/2000, double-click "My
Computer" and then double-click the
CD-ROM icon.
Caution
4
Double-click the "Setup" icon (
Note
5
).
If the language selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally the correct language
is selected automatically.)
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
8
If you are running Windows 2000/XP
and a warning message appears
regarding the Windows logo test or
digital signature, be sure to click
"Continue Anyway" or "Yes".
When the finish screen appears, click
the "Close" button.
A message will appear instructing you to
connect the machine to your computer.
Click the "OK" button.
Note
After the installation, a message
prompting you to restart your computer
may appear. In this case, click the
"Yes" button to restart your computer.
3
!!install_ar230270.book
4 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
9
Make sure that the power of the machine
is turned on, and then connect the USB
cable. (p. 12)
Windows will detect the machine and the
Plug and Play screen will appear.
10
Begin installation of the printer driver.
"SHARP AR-XXXX" will appear in the "Found
New Hardware Wizard" dialog box. Select
"Install the software automatically
(Recommended)" and click the "Next" button.
Follow the on-screen instructions.
Caution
If you are running Windows 2000/XP
and a warning message appears
regarding the Windows logo test or
digital signature, be sure to click
"Continue Anyway" or "Yes".
This completes the installation of the
software.
After installation, see "CONFIGURING THE
PRINTER DRIVER" (p. 13) to check the printer
driver settings.
4
!!install_ar230270.book
5 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
CUSTOM INSTALLATION
The procedure for a custom installation of the software is explained below. Use the custom installation
procedure when the machine is connected by a parallel cable, when the machine is used as a shared
printer on a network, or when installing the PC-FAX driver.
Installation in Windows XP (USB/Parallel cable)
1
The USB or parallel cable must not be
connected to the machine. Make sure
that the cable is not connected before
proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click the
"Cancel" button to close the window and
disconnect the cable.
Note
Insert the CD-ROM into your computer's
CD-ROM drive.
3
Click the "start" button, click "My
Computer" ( ), and then double-click
the CD-ROM icon ( ).
Double-click the "Setup" icon (
Note
Click the "Custom" button.
8
Click the "Printer Driver" button.
The cable will be connected in step
15.
2
4
7
To view information on the software, click
the "Display Readme" button.
).
If the language selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally the correct language
is selected automatically.)
5
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
6
Read the message in the "Welcome"
window and then click the "Next" button.
9
Click the "Next" button.
5
!!install_ar230270.book
6 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
10
When you are asked how the printer is
connected, select "Connected to this
computer" and click the "Next" button.
14
Click the "Close" button.
A message will appear instructing you to
connect the machine to your computer.
Click the "OK" button.
Note
15
11
A confirmation window appears. Check
the contents and then click the "Next"
button.
12
Click the "Next" button.
Begin installation of the printer driver.
Caution
If the following screen appears while the
files are being copied (the message may
appear more than once), click the
"Continue Anyway" button.
After the installation, a message
prompting you to restart your computer
may appear. In this case, click the
"Yes" button to restart your computer.
Connect the interface cable to the
machine and your computer (p. 12).
• If you are using a USB cable, make
sure the machine's power is turned on
and then connect the cable.
• If you are using a parallel cable, turn off
the power of the machine and your
computer, connect the cable, turn on the
power of the machine, and then turn on
your computer.
Windows will detect the machine and the
Plug and Play screen will appear.
16
Begin installation of the printer driver.
"SHARP AR-XXXX" will appear in the "Found
New Hardware Wizard" dialog box. Select
"Install the software automatically
(Recommended)" and click the "Next" button.
Follow the on-screen instructions.
Caution
13
6
When "The installation of the SHARP
software is complete" appears, click the
"OK" button.
If a warning window appears
regarding the "Windows logo test", be
sure to click the "Continue Anyway"
button.
This completes the installation of the
software.
After installation, see "CONFIGURING THE
PRINTER DRIVER" (p. 13) to check the printer
driver settings.
!!install_ar230270.book
7 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
Installation in Windows 98/Me/2000 (USB cable)
1
The USB cable must not be connected
to the machine. Make sure that the
cable is not connected before
proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click the
"Cancel" button to close the window and
disconnect the cable.
Note
Click the "Custom" button.
8
Click the "Printer Driver" button.
To view information on the software, click
the "Display Readme" button.
9
Click the "Next" button.
10
When you are asked how the printer is
connected, select "Connected to this
computer" and click the "Next" button.
The cable will be connected in step 16.
2
Insert the CD-ROM into your computer's
CD-ROM drive.
3
Double-click "My Computer" ( ), and
then double-click the CD-ROM icon ( ).
4
Double-click the "Setup" icon (
Note
7
).
If the language selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally the correct language
is selected automatically.)
5
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
6
Read the message in the "Welcome"
window and then click the "Next" button.
7
!!install_ar230270.book
8 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
11
When the interface selection screen
appears, select "USB" and click the
"Next" button.
15
Click the "Close" button.
A message will appear instructing you to
connect the machine to your computer.
Click the "OK" button.
Note
12
13
A confirmation window appears. Check
the contents and then click the "Next"
button.
Click the "Next" button.
In Windows 98/Me, click the "Yes" button.
Begin installation of the printer driver.
Caution
14
8
In Windows 2000, if the following
screen appears while the files are
being copied (the message may
appear more than once), click the
"Yes" button.
When "The installation of the SHARP
software is complete" appears, click the
"OK" button.
After the installation, a message
prompting you to restart your
computer may appear. In this case,
click the "Yes" button to restart your
computer.
16
Make sure that the power of the machine
is turned on, and then connect the USB
cable. (p. 12)
Windows will detect the machine and the
Plug and Play screen will appear.
17
Follow the instructions in the Plug and
Play screen that appears in your version
of Windows to begin the installation.
This completes the installation of the
software.
After installation, see "CONFIGURING THE
PRINTER DRIVER" (p. 13) to check the printer
driver settings.
!!install_ar230270.book
9 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
Installation in Windows 95/98/Me/NT 4.0/2000 (Parallel cable)
1
The parallel cable must not be
connected to the machine. Make sure
that the cable is not connected before
proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click the
"Cancel" button to close the window and
disconnect the cable.
Note
Click the "Printer Driver" button.
To view information on the software, click
the "Display Readme" button.
The cable will be connected in step 17.
2
Insert the CD-ROM into your computer's
CD-ROM drive.
3
Double-click "My Computer" ( ), and
then double-click the CD-ROM icon ( ).
4
Double-click the "Setup" icon (
Note
8
).
If the language selection screen appears
after you double click the "Setup" icon,
select the language that you wish to use
and click the "Next" button. (Normally the
correct language is selected automatically.)
5
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
6
Read the message in the "Welcome"
window and then click the "Next" button.
7
Click the "Custom" button.
9
Click the "Next" button.
If you are using Windows 95/NT 4.0, go to
step 12.
10
When you are asked how the printer is
connected, select "Connected to this
computer" and click the "Next" button.
9
!!install_ar230270.book
10 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
11
When the interface selection screen
appears, select "Parallel" and click the
"Next" button.
15
When "The installation of the SHARP
software is complete" appears, click the
"OK" button.
16
Click the "Close" button.
A message will appear instructing you to
connect the machine to your computer.
Click the "OK" button.
Note
12
Select the printer port and click the
"Next" button.
Select "LPT1" for the printer port.
17
After the installation, a message
prompting you to restart your computer
may appear. In this case, click the "Yes"
button to restart your computer.
Turn off the power of the machine and
your computer, and connect the
machine to your computer with the
parallel cable. (p. 12)
After connecting the machine to your
computer, turn on the power of the machine
and then start up your computer.
This completes the installation of the
software.
After installation, see "CONFIGURING THE
PRINTER DRIVER" (p. 13) to check the printer
driver settings.
Note
If "LPT1" does not appear, another printer
or peripheral device is using LPT1. In this
case continue the installation, and after the
installation is finished, change the port
setting so that the machine can use LPT1.
This procedure is explained in "Another
printer is using the parallel port (when
using a parallel cable)" on page 15.
13
When the model selection window
appears, select model name of your
machine and click the "Next" button.
For the model name of your machine, see
"PART NAMES AND FUNCTIONS" in the
operation manual for copier.
14
Click the "Next" button.
In Windows 95/98/Me/NT 4.0, click the
"Yes" button.
Begin installation of the printer driver.
10
!!install_ar230270.book
11 ページ 2004年2月19日 木曜日 午後1時17分
INSTALLING THE SOFTWARE
INSTALLING THE PC-FAX DRIVER
Note
• When installing the PC-FAX driver, a system file must be updated before the driver can be installed.
For more information, click the "Display Readme" button on the software selection window.
• If the PC-FAX function will be used over a USB connection, install the printer driver before
installing the PC-FAX driver.
• The PC-FAX driver can only be used if the facsimile expansion kit is installed.
1
The USB or parallel cable must not be
connected to the machine. Make sure
that the cable is not connected before
proceeding.
If the cable is connected, a Plug and Play
window will appear. If this happens, click
the "Cancel" button to close the window and
disconnect the cable.
2
Insert the CD-ROM into your computer's
CD-ROM drive.
3
Click the "start" button, click "My
Computer" ( ), and then double-click
the CD-ROM icon ( ).
In Windows 95/98/Me/NT 4.0/2000,
double-click "My Computer" and then
double-click the CD-ROM icon.
4
Double-click the "Setup" icon (
Note
5
).
8
Click the "PC-FAX Driver" button.
To view information on the software, click
the "Display Readme" button.
9
Click the "Next" button.
10
Follow the on-screen instructions.
• When the model selection window appears,
select model name of your machine.
• When the port selection window appears,
select the port that the printer driver uses.
If the language selection screen
appears after you double click the
"Setup" icon, select the language that
you wish to use and click the "Next"
button. (Normally the correct language
is selected automatically.)
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement,
and then click the "Yes" button.
6
Read the message in the "Welcome"
window and then click the "Next" button.
7
Click the "Custom" button.
Note
• The port used by the printer driver is
indicated by a checkmark in the "Ports"
tab of the printer driver properties
window. (In Windows 95/98/Me, the
port is selected in "Print to the following
port" in the "Details" tab.)
• The USB port name will vary
depending on the number of USB
ports created on your computer. If the
port created during installation of the
printer driver is your first USB port,
the name will be "USB001".
11
!!install_ar230270.book
12 ページ 2004年2月19日 木曜日 午後1時17分
CONNECTING TO A COMPUTER
Follow the procedure below to connect the machine to your computer.
Interface cables for connecting the machine to your computer are not included with the machine. Please
purchase the appropriate cable for your computer.
Interface cable
USB cable
Shielded twisted pair cable, high-speed transmission equivalent (9 feet (3 m) max.)
If the machine will be connected using a USB 2.0 interface, please purchase a USB cable that supports
USB 2.0.
Parallel cable
IEEE 1284-Shielded type bi-directional parallel interface cable (9 feet (3 m) max.)
Caution
• USB is available on a PC/AT compatible computer that was originally equipped with USB and had
Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP
Home Edition preinstalled.
• Do not connect the interface cable before installing the printer driver. The interface cable must be
connected during installation of the printer driver.
CONNECTING A USB CABLE
1
Insert the cable into the USB connector
on the machine.
2
Insert the other end of the cable into
your computer's USB connector.
Note
The cable can also be inserted into a
USB 1.1 connector.
CONNECTING A PARALLEL CABLE
1
Ensure that your computer and the
machine are turned off.
2
Insert the cable into the parallel
connector on the machine and fasten
with the clasps.
12
3
Insert the other end of the cable into
your computer's parallel connector.
!!install_ar230270.book
13 ページ 2004年2月19日 木曜日 午後1時17分
CONFIGURING THE PRINTER DRIVER
After installing the printer driver, you must configure the printer driver settings appropriately for the
number of paper trays on the machine and the size of paper loaded in each tray.
1
Click the "start" button, click "Control
Panel", click "Printers and Other
Hardware", and then click "Printers and
Faxes".
In operating systems other than Windows XP, click
the "Start" button, select "Settings", and then click
"Printers".
2
Click the "SHARP AR-XXXX" printer
driver icon and select "Properties" from
the "File" menu.
If you are using Windows NT 4.0/2000/XP, go to
step 4.
3
In Windows 95/98/Me, click the "Setup"
tab.
4
Click the "Configuration" tab and set the
printer configuration based on the
options that have been installed.
Set the printer configuration properly.
Otherwise, printing may not take place
correctly.
5
Click the "Set Tray Status" button and
select the size of paper that is loaded in
each tray.
Select a tray in the "Paper source" menu,
and select the size of paper loaded in that
tray from the "Set Paper Size" menu. Repeat
for each tray.
6
Click the "OK" button in the "Set Tray
Status" window.
7
Click the "OK" button in the printer
properties window.
13
!!install_ar230270.book
14 ページ 2004年2月19日 木曜日 午後1時17分
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the machine as a printer. View the online
manual when you use the printer function after the initial setup is completed.
Contents of the online manual
The contents of the online manual are as follows.
How to use the online manual: Explains how to use the online manual.
Print: Provides information on how to print a document.
Printer sharing: Explains how to configure the machine for use as a shared printer.
Troubleshooting: Provides instructions on how to solve driver or software problems.
Note
To view the online manual, your computer must have Acrobat Reader 5.0 or later. If you do not
have Acrobat Reader, follow the instructions in "Installing Acrobat Reader" to install it.
1
Insert the CD-ROM into your computer's
CD-ROM drive.
2
Click the "start" button, click "My
Computer" ( ), and then double-click
the CD-ROM icon ( ).
In Windows 95/98/Me/NT 4.0/2000,
double-click "My Computer" and then
double-click the CD-ROM icon.
Note
Double-click the "Manual" folder,
double-click the "EnglishA" folder (for
regions other than the U.S., double-click
the "English" folder), and then
double-click the "AR_M230_M270.pdf"
icon.
The online manual will appear.
• If you will be viewing the online manual repeatedly, you may find it convenient to copy this online
manual file to your computer.
• The online manual can be printed out using Acrobat Reader. SHARP recommends printing out
the sections which you refer to regularly.
• Refer to "Help" of Acrobat Reader for more details on how to use Acrobat Reader.
Installing Acrobat Reader
1
Insert the CD-ROM into your computer's
CD-ROM drive.
2
Click the "start" button, click "My
Computer" ( ), and then double-click
the CD-ROM icon ( ).
In Windows 95/98/Me/NT4.0/2000,
double-click "My Computer" and then
double-click the CD-ROM icon.
3
Double-click the "Acrobat" folder, and
then double-click the "ar500enu.exe"
icon.
Follow the on-screen instructions to install
Acrobat Reader.
14
3
!!install_ar230270.book
15 ページ 2004年2月19日 木曜日 午後1時17分
TROUBLESHOOTING
If the software does not install correctly, check the following items on your computer.
To remove the software, see "Uninstalling the printer driver" in the online manual.
Troubleshooting information can also be found in the README files for each of the software programs. To
view a README file, click the "Display Readme" button in the "Software Selection" screen.
Printer driver cannot be
installed (Windows 2000/XP)
Another printer is using the parallel
port (when using a parallel cable)
If the printer driver cannot be installed in
Windows 2000/XP, follow these steps to check
your computer's settings.
If another printer is using the parallel port and
printing is not possible using the machine, follow
the steps below to change the port setting of the
other printer driver, and make sure that the port of
the printer driver for the machine is set to LPT1.
1
2
Click the "start" button and then click
"Control Panel".
In Windows 2000, click the "Start" button,
select "Settings", and then click "Control
Panel".
Click "Performance and Maintenance",
and then click "System".
In Windows 2000, double-click the
"System" icon.
3
Click the "Hardware" tab and then click
the "Driver Signing" button.
4
Check "What action do you want
Windows to take?" ("File signature
verification" in Windows 2000).
If the option "Block" has been selected, it
will not be possible to install the printer
driver. Select the option "Warn" and then
install the printer driver as explained in
"Installation in Windows XP (USB/Parallel
cable)".
1
Click the "start" button, click "Control
Panel", click "Printers and Other
Hardware", and then click "Printers and
Faxes".
In Windows 95/98/Me/NT 4.0/2000, click
the "Start" button, select "Settings", and
then click "Printers".
2
Click the icon of the printer driver for which
you wish to change the port setting, and
select "Properties" from the "File" menu.
3
Click the "Ports" tab.
In Windows 95/98/Me, click the "Details" tab.
4
Select "FILE:" in the "Print to the following
port" list box, and click the "OK" button.
5
Click the "SHARP AR-XXXX" printer
driver icon and select "Properties" from
the "File" menu.
6
Click the "Ports" tab.
In Windows 95/98/Me, click the "Details" tab.
7
Select "LPT1" in the "Print to the
following port" list box, and click the
"OK" button.
Note
In the event that you need to use the
other printer, repeat the above steps
to set the port of the machine to
"FILE:", and change the port setting of
the other printer back to "LPT1".
15
!!install_ar230270.book
16 ページ 2004年2月19日 木曜日 午後1時17分
TROUBLESHOOTING
The printer driver cannot be
correctly installed by Plug and
Play (Windows 2000/XP)
In Windows 2000/XP, if the printer driver cannot
be correctly installed by Plug and Play (for
example, Plug and Play takes place without
copying the required files for the printer driver
installation), follow these steps to remove
unneeded devices and then install the printer
driver as explained in "Installation in Windows
XP (USB/Parallel cable)" (p. 5).
1
2
Click the "start" button, click "Control
Panel", and then click "Performance and
Maintenance".
In Windows 2000, click the "Start" button,
select "Settings", and then click "Control
Panel".
If the Plug and Play screen does not appear after
you connect the machine to your computer with a
USB cable and turn on the machine, follow the
steps below to verify that the USB port is
available.
1
Click the "start" button, click "Control
Panel", and then click "Performance and
Maintenance".
In Windows 98/Me/2000, click the "Start"
button, select "Settings", and then click
"Control Panel".
2
Click "System", click the "Hardware"
tab, and click the "Device Manager"
button.
"Universal Serial Bus controllers" will
appear in the list of devices.
Click "System", click the "Hardware"
tab, and click the "Device Manager"
button.
Note
3
Plug and play screen does not
appear (when using a USB cable)
Note
In Windows 2000, double-click the
"System" icon, click the "Hardware"
tab, and click the "Device Manager"
button.
Click the
devices".
icon beside "Other
3
• In Windows 98/Me, double-click the
"System" icon and click the "Device
Manager" tab.
• In Windows 2000, double-click the
"System" icon, click the "Hardware"
tab, and click the "Device Manager"
button.
• If the "System" icon does not appear
in Windows Me, click "view all
Control Panel options".
Click the
icon beside "Universal
Serial Bus controllers".
If "SHARP AR-XXXX" appears, select and
delete it.
Note
4
If "Other devices" does not appear,
close the "Device Manager" window.
Two items should appear: your controller
chipset type and Root Hub. If these items
appear, you can use the USB port. If the
"Universal Serial Bus controllers" shows a
yellow exclamation point or does not
appear, you must check your computer
manual for USB troubleshooting or contact
your computer manufacturer.
Install the software as explained in
"Installation in Windows XP
(USB/Parallel cable)".
4
16
Once you have verified that the USB port
is enabled, install the software as
explained in "Installation in Windows
XP (USB/Parallel cable)".
!!install_ar230270.book
1 ページ 2004年2月19日 木曜日 午後1時17分
!!install_ar230270.book
2 ページ 2004年2月19日 木曜日 午後1時17分
AR-M236/AR-M237/AR-M276/AR-M277
SHARP CORPORATION
Printed on 100% post-consumer recycled paper
PRINTED IN CHINA
KS2
2004C
TINSE1053QSZZ