Epson PowerLite 700 User`s guide

PowerLite Home Cinema 700
Home Theater Projector
®
User’s Guide
Important Safety Information
WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Software Copyright:
This product uses free software as well as software to which this company holds the rights.
The following is information on the free software used by this product.
Hereafter, each author, the conditions, and so on are described in the original. Furthermore, there is no guarantee
for free software because of the characteristics of the free software that has already been used in this product; any
problems in this product (including problems that originate with the free software concerned) do not influence the
conditions of the guarantee (written guarantee) issued by this company.
(1) libjpeg
© 1991-1998 Thomas G. Lane.
This software is based in part on the work of the Independent JPEG Group.
(2) libpng
© 1998-2004 Glenn Randers-Pehrson
© 1996-1997 Andreas Dilger
© 1995-1996 Guy Eric Schalnat, Group 42, Inc.
(3) zlib
© 1995-2003 Jean-loup Gailly and Mark Adler
2
Trademarks
Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation.
PowerLite and PrivateLine are registered trademarks, SizeWise is a trademark, and Extra Care is a service mark of
Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2008 Epson America, Inc.
7/08
3
4
C
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10
Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Projector Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Control Map. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Projector Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1
Setting Up the Projector . . . . . . . . . . . . . . . . . . . . . 17
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 18
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Determining Projection Distance. . . . . . . . . . . . . . . . . . 20
Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 23
Connecting an HDMI Video Source . . . . . . . . . . . . . . . 24
Connecting a Component Video Source . . . . . . . . . . . . 25
Connecting a Composite Video Source . . . . . . . . . . . . . 26
Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 27
Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 28
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting to the USB Port . . . . . . . . . . . . . . . . . . . . . 29
Connecting to the VGA Computer Port . . . . . . . . . . . . 31
Playing Sound Through the Projector. . . . . . . . . . . . . . . . . . 32
Connecting a Digital Camera or Other USB Device. . . . . . . 32
Inserting an SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . 35
Using the Direct Power On Function . . . . . . . . . . . . . . 37
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . 38
5
6
2
Displaying and Adjusting the Image . . . . . . . . 39
Selecting an Image Source . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Adjusting the Position of the Image . . . . . . . . . . . . . . . . 41
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 41
Focusing and Zooming the Image . . . . . . . . . . . . . . . . . 42
Selecting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 43
Resizing Video Images . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3
Presenting With the Remote Control . . . . . . . . 45
4
Fine-Tuning the Projector. . . . . . . . . . . . . . . . . . . 55
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 46
Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 46
Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Zooming In on Your Image . . . . . . . . . . . . . . . . . . . . . . 47
Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 48
Operating Your Computer With the Remote Control . . . . . 48
Presenting a Slideshow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Starting a Slideshow. . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Selecting Slideshow Display Options . . . . . . . . . . . . . . . 52
Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 57
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 61
Customizing Power and Operation . . . . . . . . . . . . . . . . . . . 62
Using the Projector Security Features . . . . . . . . . . . . . . . . . . 63
Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 64
Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 66
Disabling the Projector’s Buttons. . . . . . . . . . . . . . . . . . 68
Using Security Locking . . . . . . . . . . . . . . . . . . . . . . . . . 69
5
Maintaining the Projector . . . . . . . . . . . . . . . . . . . 71
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Replacing the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 76
Checking Lamp Usage . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Replacing the Remote Control Batteries . . . . . . . . . . . . . . . . 78
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6
Solving Problems
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Checking Projector Status. . . . . . . . . . . . . . . . . . . . . . . . . . . 83
What To Do When the Lights Come On or Flash . . . . . 83
Solving Projector Operation Problems . . . . . . . . . . . . . . . . . 85
Solving Problems With the Image or Sound . . . . . . . . . . . . . 85
Solving Problems With the Remote Control. . . . . . . . . . . . . 91
Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Speak to a Support Representative . . . . . . . . . . . . . . . . . 92
A
Technical Specifications . . . . . . . . . . . . . . . . . . . . . 95
B
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 101
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 104
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
7
8
W
-
Welcome
The PowerLite
®
Home Cinema 700 lets you enjoy High-Definition,
theater-quality images in the relaxing environment of your own home.
You can connect it to a wide range of video sources and computers, so
you can enjoy perfectly adjusted images from all your movies and
games.
Your compact, lightweight projector offers these outstanding features:
■
720p High-Definition performance
■
Native WXGA resolution (1280 × 800) with up to 2000 lumens
of White and Color Light Output (brightness)
■
HDMI™ (High Definition Multimedia Interface™) port for
superior, uncompressed digital video
■
SD™ card slot and USB thumb drive port for PC-free slideshows
■
Seven color modes to optimize viewing for different environments
and image content
■
Flexible setup options, including front projection and ceiling
mounted
■
USB port for easy projection from a Windows® computer
■
Instant Off ®/On power modes for quick setup and take-down
■
Auto Keystone correction and 1.2X optical zoom for easy picture
adjustments
■
Password protection, projector button lock, and security cable
attachments for parental control and security
■
Integral lens cover that won’t get lost
■
Low power, long-lasting lamp with High and Low Brightness
modes
9
Using Your Documentation
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■
Warnings must be followed carefully to avoid bodily injury.
■
Cautions must be observed to avoid damage to your equipment.
■
Notes contain important information about your projector.
■
Tips contain additional projection hints.
Here’s where you can look for even more information:
■
Quick Setup sheet
Provides information for connecting the projector to your
equipment, displaying and adjusting the image, and solving
display problems.
■
Built-in help system
Provides assistance for common problems. Available from the
? Help button on the projector or the remote control. See page 82
for details.
■
epson.com/support
Download FAQs and e-mail your questions to Epson support.
■
PrivateLine® support
If you still need help after checking this User’s Guide and the
sources listed in this section, you can use the Epson PrivateLine
Support service to get help fast. Call (800) 637-7661 and enter
the PIN on the PrivateLine card. Or take advantage of Epson’s
automated support services 24 hours a day. See page 92 for more
information.
10
Welcome
Projector Parts
Kensington
lock port
Control panel
Lens cover
Focus and
Zoom rings
Infrared
receiver
Adjustable
foot
SD card
slot
USB (TypeA)
port
Ventilation slots
USB (TypeB)
port
Video
port
Adjustable foot and
release lever
S-Video
port
Computer
(Component
Video) port
HDMI
port
Audio
ports
AC power
inlet
Infrared
receiver
Lamp
cover
Welcome 11
Mounting bracket holes
(M4×9 screws required)
Air filter
Security
cable slot
Projector Control Panel
Source Search button
(searches for connected
video sources)
Menu button
(displays
projector menus)
Esc button
(exits menu
items)
Power light
and button
Lamp and
Temperature
warning
lights
12
Welcome
Enter button
(selects
menu items)
Help
button
Volume
down
button
Keystone
buttons
(correct screen
shape)
Volume up
button
Remote Control Map
Power
button
Search and Source buttons
(select image source)
A/V Mute button
(turns off image)
Auto button
(resets tracking,
sync, and position)
Aspect button
(changes screen size)
Page Up/Down buttons
(control PowerPoint® slides;
USB cable required)
Freeze button
(stops image)
Color Mode button
(changes display mode)
Num button
(activates number
buttons)
Help button
(displays help menus)
E-Zoom +/– buttons
(zoom into image)
Volume buttons
(adjusts volume)
Menu button
(accesses menus)
Esc button
(exits menus)
Menu navigation buttons
and Enter button
Welcome 13
Projector Dimensions
Use the dimensions below to guide you in placing or installing the
projector.
Center of lens
3.73 in.
(94.7 mm)
0.26 in.
(6.7 mm)
3.21 in.
(81.5 mm)
1.95 in.
(49.6 mm);
center of lens
to mounting
bracket holes
12.87 in.
(327 mm)
3.64 in.
(92.5 mm)
3.62 in.
(92 mm)
9.65 in.
(245 mm)
0.47 in.
(12 mm)
4.53 in.
(115 mm)
14
Welcome
5 in.
(127 mm)
2.66 in.
(67.5 mm)
Registration and Warranty
Your projector comes with a basic warranty that lets you project with
confidence. For details, see the warranty brochure included with your
projector.
In addition, Epson offers free Extra Care Home Service. In the
unlikely event of an equipment failure, you won’t have to wait for
your unit to be repaired. Instead, Epson will ship you a replacement
unit anywhere in the United States or Canada, usually via overnight
delivery. See the brochure included with your projector for details.
SM
To register, simply fill out the registration card and mail it to Epson.
Or you can register online at epson.com/webreg. Registering also lets
you receive special updates on new accessories, products, and service.
Optional Accessories
To enhance your use of the projector, Epson offers the following
optional accessories:
Product
Part number
Replacement lamp
V13H010L41
Replacement air filter
V13H134A13
Universal projector ceiling mount
Advanced projector ceiling mount with precision gear
High security projector ceiling mount
Adjustable suspended ceiling channel kit
False ceiling plate kit
Structural round ceiling plate
Adjustable extension column (pipe) 8” - 11”
ELPMBPJF
ELPMBPRG
ELPMBATA
ELPMBP01
ELPMBP02
ELPMBP03
ELPMBC01
Kensington security lock
ELPSL01
50-inch portable screen (4:3 aspect ratio)
60-inch portable pop-up screen (4:3 aspect ratio)
80-inch portable pop-up screen (4:3 aspect ratio)
Accolade™ DUET™ Portable Projector Screen (4:3/16:9)
ELPSC06
ELPSC07
ELPSC08
ELPSC80
Component-to-VGA video cable
S-Video cable
ELPKC19
ELPSV01
Welcome 15
Product
Part number
Distribution amplifier
ELPDA01
Image presentation camera (ELPDC05)
DC-10s document camera
V12H162020
ELPDC10S
Soft carrying case (projector only)
Soft shoulder case for projector and notebook
Wheeled soft carrying case
Molded hard-shell wheeled carrying case
Swiss Gear® backpack
V12H00160
ELPKS61
ELPKS62
ELPKS58
ELPKS63
You can purchase screens or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com
(U.S. sales) or www.epson.ca (Canadian sales).
16
Welcome
1
1
Setting Up the Projector
T
his chapter tells you how to unpack the projector and connect it to
video equipment, such as a VCR, DVD player, or video camera,
and/or to a notebook or desktop computer.
You can also connect the projector to a USB storage device or digital
camera, or project from an inserted SD card.
Follow the instructions in this chapter on:
■
Unpacking the projector
■
Positioning the projector
■
Connecting to a computer
■
Connecting to video equipment
■
Playing sound through the projector
■
Connecting to a digital camera or other USB device
■
Inserting an SD card
■
Turning the projector on and off
17
Unpacking the Projector
After unpacking the projector, make sure you have all these parts:
PDF manual and
registration CD-ROM
Component-to-VGA
video adapter
Projector
Power cord
Remote control
and batteries
Save all packaging in case you need to ship the projector. Always use
the original packaging (or the equivalent) when you need to send the
projector to another location; see page 79 for instructions.
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
18
Setting Up the Projector
■
To receive an HDMI signal from your video device, you’ll need
an HDMI cable. One may be provided with your video
equipment.
■
To receive a component video signal from a DVD player or other
video device, you’ll need a component video cable (one may be
provided with your video equipment) and the
component-to-VGA video adapter that came with the projector.
■
To receive an S-Video signal, you’ll need an S-Video cable. One
may be included with your video equipment, or you can purchase
one from Epson. See “Optional Accessories” on page 15.
■
To receive an audio signal, you’ll need an RCA-type audio cable
with two male plugs, or a stereo mini-jack audio adapter cable
(not necessary with HDMI connection).
Positioning the Projector
You can place the projector in a variety of viewing setups.
When projecting from the front, place the projector directly in front
of the center of the screen, facing the screen squarely. The center of
the lens should be about level with the bottom of the screen.
note
After positioning the
projector, you may want to
connect a Kensington
MicroSaver® anti-theft
device to the lock port on the
projector. You can purchase
this from Epson; see
page 15.
If you place the projector below screen level, you may need to tilt it up
by extending the front adjustable foot (see page 41). Tilting the
projector causes the image to become “keystone” shaped, but you can
correct the distortion (see page 41).
You can also install the projector on the ceiling using the optional
ceiling mounting hardware (see page 15). Use the projector
dimensions on page 14 to assist you in installing the projector.
Setting Up the Projector 19
You can also install the projector in two other viewing setups: rear
projection onto a semi-transparent screen, or rear/ceiling projection.
If you project from overhead or the rear of the screen, you’ll need to
select the appropriate Projection setting in the projector’s Extended
menu to orient the image correctly (see page 62).
Keep these considerations in mind as you position the projector:
■
Place the projector on a sturdy, level surface.
■
Make sure there is plenty of space for ventilation around and
under the projector.
■
Make sure the projector is within 5.9 feet (1.8 meters) of a
grounded electrical outlet or extension cord.
Determining Projection Distance
Image size increases with distance, but can vary depending on the
aspect ratio (image shape), how you zoom into the image, and
whether you’ve adjusted other image settings. Use the illustrations and
tables below to help you determine the projection distance.
Center of
lens
Center of lens
16:10 image
20
Setting Up the Projector
Diagonal screen
size
Projection distance (A)
Wide to Tele
27 inches
(69 cm)
33 to 40 inches
(84 to 101 cm)
30 inches
(76 cm)
37 to 45 inches
(94 to 113 cm)
40 inches
(102 cm)
50 to 60 inches
(126 to 152 cm)
16:10 image
Diagonal screen
size
Projection distance (A)
Wide to Tele
50 inches
(127 cm)
62 to 75 inches
(158 to 191 cm)
60 inches
(152 cm)
75 to 90 inches
(191 to 230 cm)
80 inches
(203 cm)
101 to 121 inches
(255 to 307 cm)
100 inches
(254 cm)
126 to 152 inches
(320 to 385 cm)
150 inches
(381 cm)
190 to 228 inches
(482 to 579 cm)
200 inches
(508 cm)
253 to 305 inches
(644 to 774 cm)
250 inches
(635 cm)
317 to 381 inches
(806 to 968 cm)
4:3 image
Screen size
Projection distance (A)
Wide to Tele
24 inches
(61 cm)
33 to 40 inches
(84 to 102 cm)
30 inches
(76 cm)
42 to 51 inches
(106 to 129 cm)
40 inches
(102 cm)
56 to 68 inches
(143 to 173 cm)
50 inches
(127 cm)
71 to 85 inches
(180 to 217 cm)
60 inches
(152 cm)
85 to 103 inches
(216 to 260 cm)
70 inches
(178 cm)
100 to 120 inches
(253 to 304 cm)
80 inches
(203 cm)
114 to 137 inches
(290 to 348 cm)
100 inches
(254 cm)
143 to 172 inches
(363 to 436 cm)
150 inches
(381 cm)
215 to 258 inches
(546 to 656 cm)
Setting Up the Projector 21
4:3 image
Screen size
Projection distance (A)
Wide to Tele
200 inches
(508 cm)
287 to 345 inches
(729 to 876 cm)
235 inches
(597 cm)
338 to 406 inches
(857 to 1030 cm)
16:9 image
22
Setting Up the Projector
Screen size
Projection distance (A)
Wide to Tele
Offset (B)
27 inches
(69 cm)
34 to 41 inches
(86 to 104 cm)
0.7 inch
(2 cm)
30 inches
(76 cm)
38 to 46 inches
(96 to 116 cm)
0.8 inch
(2 cm)
40 inches
(102 cm)
51 to 62 inches
(130 to 156 cm)
1.1 inches
(3 cm)
50 inches
(127 cm)
64 to 77 inches
(163 to 196 cm)
1.4 inches
(3 cm)
60 inches
(152 cm)
77 to 93 inches
(196 to 236 cm)
1.6 inches
(4 cm)
70 inches
(178 cm)
90 to 109 inches
(229 to 276 cm)
1.9 inches
(5 cm)
80 inches
(203 cm)
103 to 124 inches
(263 to 316 cm)
2.2 inches
(6 cm)
100 inches
(254 cm)
130 to 156 inches
(329 to 396 cm)
2.7 inches
(7 cm)
150 inches
(381 cm)
195 to 234 inches
(495 to 596 cm)
4.1 inches
(10 cm)
200 inches
(508 cm)
261 to 313 inches
(662 to 795 cm)
5.5 inches
(14 cm)
260 inches
(660 cm)
339 to 407 inches
(861 to 1035 cm)
7.1 inches
(18 cm)
Connecting to Video Equipment
You can connect several video sources to the projector at the same
time. Before starting, look at your video equipment to determine its
available video output connections:
■
If your video player has an HDMI connector, see “Connecting an
HDMI Video Source” on page 24.
■
If your video player has a component video port (three connectors
labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a
Component Video Source” on page 25.
■
If your video player has a yellow RCA video output connector, see
“Connecting a Composite Video Source” on page 26.
■
If your video player has an S-Video connector, see “Connecting
an S-Video Source” on page 27.
■
If your video player has an RGB video port, see “Connecting an
RGB Video Source” on page 28.
After connecting video cables, you may also want to connect an
optional audio cable to play sound through the projector; see page 32.
If you connect using an HDMI cable, the video and sound are both
transferred and you won’t need to connect any additional cables for
audio.
Setting Up the Projector 23
Connecting an HDMI Video Source
note
If an HDMI cable was not
provided with your video
device, you can purchase one
from an electronics dealer.
For the best image and sound quality, connect your video equipment
to the HDMI (High-Definition Multimedia Interface) port, if
possible.
Connect an HDMI cable to the HDMI connector on your player and
the HDMI port on the projector.
HDMI port
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
24
Setting Up the Projector
Connecting a Component Video Source
If your video equipment has component video connectors (three
connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use the
component-to-VGA video adapter that came with your projector and
a component video cable, or you can purchase a component-to-VGA
video cable from Epson (see page 15) or an electronics dealer.
1. Connect one end of your component video cable to the Y/Cb/Cr
(or Y/Pb/Pr) connectors on your player.
2. Connect the component end of the component-to-VGA video
adapter to the free end of the component video cable.
3. Connect the VGA end of the adapter to the Computer
(Component Video) port on your projector.
Computer (Component Video) port
4. You may need to change the Input Signal setting in the
projector’s Signal menu to Auto (see page 60).
5. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
Setting Up the Projector 25
Connecting a Composite Video Source
note
If the video cable was not
provided with your video
device, you can purchase one
from an electronics dealer.
1. If your video cable has an RCA connector, connect it to the
yellow video output connector on your player and the yellow
Video port on the projector.
Video port
2. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
26
Setting Up the Projector
Connecting an S-Video Source
1. Connect the S-Video cable to the S-Video connector on your
player and the S-Video port on the projector.
S-Video port
note
If the S-Video cable was not
provided with your video
device, you can purchase one
from Epson; see page 15.
2. If you want to play sound through the projector, see page 32 for
instructions on connecting an audio cable.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
Setting Up the Projector 27
Connecting an RGB Video Source
note
You can purchase a VGA
computer cable from an
electronics dealer.
You can connect to an RGB video source using a VGA computer
cable.
1. Connect the cable to the RGB video port on your player and the
Computer (Component Video) port on the projector.
Computer (Component Video) port
2. You may need to change the Input Signal setting in the
projector’s Signal menu to RGB (see page 60).
3. If you want to play sound through the projector, see page 32 for
instructions on connecting audio cables.
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
28
Setting Up the Projector
Connecting to a Computer
You can connect the projector to a Windows computer using the
projector’s TypeB USB port. This lets you carry a lightweight cable
with you when you transport the projector.
You can also connect the projector to any computer that has a
standard video output (monitor) port, including desktop models,
PC notebook computers, Macintosh PowerBook® and iBook®
computers, and hand-held devices. See page 31 for instructions on
connecting using a VGA computer cable.
To play sound through the projector, connect an audio cable (see
page 32).
You may be able to use your remote control as a wireless mouse when
projecting from a computer (see page 48).
Connecting to the USB Port
You can connect a Windows Vista®, XP, or Windows 2000 (SP4)
computer to the projector’s TypeB (square)
USB port and
project your computer’s display. A USB 2.0 connection
(recommended) provides better picture quality and response than
USB 1.1.
The first time you connect a computer to the projector’s USB port,
software from the projector is installed on your computer.
1. Follow the instructions beginning on page 35 to turn on the
projector.
2. Make sure the USB Type B setting on the Extended menu is set
to USB Display (see page 62).
3. Turn on your computer.
Setting Up the Projector 29
4. Connect the square end of a USB cable to the projector’s TypeB
(square)
USB port.
USB TypeB port
5. Connect the flat end of the cable to any available USB port on
your notebook or desktop computer.
Messages appear on your computer screen as the projector is
recognized and the software is installed automatically.
6. Follow the instructions on the screen to install the Epson USB
Display software. If you see a “Digital Signature Warning,” select
Continue or Continue Anyway. (You will see these instructions
only the first time you connect.)
After the software is installed, you see your computer’s current
desktop displayed by the projector. You can switch the projector
to other image sources using the Source Search or Search
button on the remote control or the projector.
7. You can connect an optional audio cable if you want to play
sound through the projector (see page 32).
When you’ve finished making connections, see Chapter 2 for
instructions on displaying and adjusting the image.
When you’re done projecting from your computer, disconnect the
USB cable.
30
Setting Up the Projector
Connecting to the VGA Computer Port
You can connect to the projector using a VGA computer cable.
1. Connect one end of a VGA computer cable to the projector’s
Computer (Component Video) port and the other end to your
computer’s monitor port.
note
You can purchase a VGA
computer cable from an
electronics dealer.
Computer (Component
Video) port
caution
Don’t try to force a
connector to fit a port with a
different shape or number of
pins. You may damage the
port or connector.
2. You may need to change the Input Signal setting in the
projector’s Signal menu to RGB (see page 60).
3. You can connect an optional audio cable to play sound through
the projector (see page 32).
4. You may also be able to use the remote control as a wireless mouse
(see page 48).
When you’ve finished making connections, see page 35 for
instructions on turning on the projector and Chapter 2 for
instructions on displaying and adjusting the image.
Setting Up the Projector 31
Playing Sound Through the Projector
You can play sound through the projector’s speaker system.
1. Locate the appropriate cable and connect it to the Audio jacks on
the projector.
Audio jacks
2. Connect the other end of the cable to the audio output
connector(s) on your computer or video equipment.
Connecting a Digital Camera or Other
USB Device
note
Use a cable less than 10 feet
(3 meters) long and connect
the camera or other device
directly to the projector.
Your projector may not
function correctly if you use
a longer cable or connect to
a USB hub.
If you connect a USB hard
drive, make sure you use the
AC adapter to power the
hard drive.
32
Setting Up the Projector
You can connect your digital camera, USB flash memory drive, USB
hard drive, or multimedia storage viewer, such as the Epson P-3000 or
Apple® iPod® to the projector. Then you can use the projector’s
Slideshow function to display images or a presentation. See page 50
for details.
Use the USB cable specified for your device.
1. Follow the instructions beginning on page 35 to turn on the
projector.
2. Connect the USB drive or the flat end of the USB cable to the
USB TypeA port on the projector, as shown.
Indicator
light
3. Connect the other end of the cable to your camera or other
device, if necessary.
The indicator light turns orange and then green when a USB
device is connected.
4. If you are not connected to another image source, the Slideshow
program appears.
If you are connected to another image source, press the
Slideshow button on the remote control to start the Slideshow
program.
See page 50 for instructions on controlling the slideshow.
5. When you’re finished, press Esc and select Exit to exit the
Slideshow before turning off or removing the USB device.
Be sure to turn off your USB device (if necessary) before you remove
the device or cable from the projector.
Setting Up the Projector 33
Inserting an SD Card
You can use an SD or SDHC™ (SD High Capacity) card to store
images or PowerPoint presentation slides converted to .JPG files. This
lets you project your files without connecting to a laptop or PC. To
place your files on the card, copy them from your computer to the
card using a card reader.
1. Follow the instructions beginning on page 35 to turn on the
projector.
2. Insert the SD card face-up and contacts-down, and push it all the
way into the projector’s SD slot:
Indicator
light
caution
Do not remove the card
when the indicator light is
flashing or on, or the
Slideshow program is
running, or you may
damage the card or
projector.
The indicator light beside the slot comes on or flashes when the
SD card is in use. Do not remove the card when the light is
flashing or on, or the Slideshow program is running.
3. If you are not connected to another image source, the Slideshow
program appears.
If you are connected to another image source, press the
Slideshow button on the remote control to start the Slideshow
program.
See page 50 for instructions on controlling the slideshow.
4. When you’re finished, press Esc and select Exit to exit the
Slideshow before removing the SD card.
34
Setting Up the Projector
To remove the card, gently press the inserted SD card. The card pops
out so you can remove it.
Turning the Projector On and Off
Turn on any connected computer or video equipment before starting
the projector so it can automatically detect and display the image
source. If you turn on the projector first, or have multiple pieces of
connected equipment, you may have to select the image source
manually (see page 40).
Follow these steps to turn on the projector:
1. Open the A/V Mute slide (lens cover).
Setting Up the Projector 35
2. Plug one end of the power cord into the projector, and the other
end into an electrical outlet.
The Ppower light turns orange.
Power light
3. Press the Ppower button on the remote control or on the
projector.
Power
button
36
Setting Up the Projector
The projector beeps once and the Ppower light flashes green as
the projector warms up, then an image begins to appear. When
the Ppower light stops flashing and remains green, the projector
is ready for use.
4. If you are prompted to enter a password, see page 65.
warning
Never look into the lens
when the lamp is on. This
can damage your eyes, and is
especially dangerous for
children.
Using the Direct Power On Function
The Direct Power On function enables faster setup. The projector
starts up automatically when you plug it in or turn it on with a wall
switch. You don’t have to press the Ppower button.
Follow these steps to enable Direct Power On:
1. Press the Menu button on the remote control or projector, then
select the Extended menu and press Enter.
2. Choose Operation and press Enter.
3. Choose Direct Power On and press Enter.
note
4. Highlight On and press Enter.
If a power outage occurs
when Direct Power On is
enabled and the projector is
plugged in, the projector will
restart when the power is
restored.
5. Press Menu to exit. The setting will take effect the next time you
plug in the projector.
Setting Up the Projector 37
Shutting Down the Projector
note
Lamp life results will vary
depending upon mode
selected, environmental
conditions, and usage.
This projector incorporates Instant Off technology. To turn it off, you
can press its Ppower button as described below, unplug it, or turn off
a power switch that supplies power to the projector. You don’t have to
wait for the projector to cool down first.
Turn off this product when
not in use to prolong the life
of the projector.
1. To turn off the projector, press the Ppower button on the remote
control or projector.
You can set the projector to
automatically turn off the
lamp and enter “sleep mode”
when it has not received any
signals for 1 to 30 minutes
(see page 62). This conserves
electricity, cools the
projector, and extends the
life of the lamp. If you want
to start projecting again,
press the P power button.
If you are done using the
projector, unplug the power
cord.
38
Setting Up the Projector
You see a confirmation message.
(If you don’t want to turn it off,
press any other button.)
2. Press the Ppower button again. The projection lamp turns off
and the projector beeps twice. You can then unplug the power
cord.
If you want to turn the projector on again, make sure the orange
Ppower light is not flashing, then press the Ppower button.
2
2
Displaying and Adjusting
the Image
Follow the guidelines in this chapter for:
■
Selecting an image source
■
Adjusting the image
39
Selecting an Image Source
You may need to select the image source if you have multiple image
sources connected to the projector (such as a computer or DVD
player). Selecting the image source lets you switch between images
input from different pieces of connected equipment.
If you don’t see the image you want, press the Search button or one
of the Source buttons on the remote control, or press the Source
Search button on the projector.
Search
button
Source
Search
button
Source
buttons
If you still can’t see an image or can’t project the same image that is on
your notebook or computer screen, see page 85 for solutions.
You can also select Slideshow to project from a USB device or
SD card. See page 50 for instructions.
Adjusting the Image
Once you see your image, you may need to make certain adjustments:
40
■
If the image is too high or too low, reposition it as described on
page 41.
■
If the image isn’t square, see page 41.
■
To focus or zoom your image, see page 42.
■
To quickly adjust the color mode, see page 43.
■
To change the image size (aspect ratio), see page 44.
■
If you need to fine-tune the image and/or sound, see
“Fine-Tuning the Projector” on page 55.
Displaying and Adjusting the Image
Adjusting the Position of the Image
If the image is too low on the screen, you can use the front adjustable
foot to raise it.
1. Press the foot release lever up and lift the front of the projector.
2. Once the image is positioned where you want it, release the lever
to lock the foot in position.
3. If the image is tilted or you need to fine-tune the height of the
image, you can turn the projector’s adjustable rear feet.
Raising the projector may cause the image shape to distort or
“keystone,” but you can correct the shape as described below.
Adjusting the Image Shape
You can maintain a rectangular image by placing the projector directly
in front of the screen and keeping it level. This also produces the best
picture quality. If the projector is tilted up or down (up to 30°), or
placed at an angle, the shape may “keystone” and you may need to
correct the image shape.
Displaying and Adjusting the Image 41
The projector’s Auto Keystone function detects and corrects vertical
keystone distortion up to 11°. It takes about one second after the
projector starts for the image to be corrected.
If your image is still distorted, do one of the following:
■
Press the appropriate keystone correction button on the
projector’s control panel until the shape is evenly rectangular.
Keystone correction
buttons
■
Select the Keystone setting in the projector’s Settings menu (see
page 61). Then use the arrow buttons on the remote control to
adjust the shape of the image.
Focusing and Zooming the Image
Turn the focus ring on the projector to sharpen the image.
To enlarge or reduce the image, turn the zoom ring.
If the image still isn’t large enough, you may need to move the
projector farther away from the screen.
42
Displaying and Adjusting the Image
You can also use the E-Zoom buttons on the remote control to zoom
in on a portion of the image. See page 47 for instructions.
Selecting the Color Mode
The Color Mode adjusts the brightness, contrast, and color for various
common viewing environments. Use this setting to quickly obtain a
good picture.
Press the Color Mode button on the remote control until the option
you want is projected in the upper right corner.
Color Mode
button
You can also select the Color Mode setting from the projector’s Image
menu. See page 57 for instructions.
Select from one of these Color Mode options:
■
Game: Brightest mode; for video games or TV in a bright room.
■
Theatre: For natural-toned movies in a darkened room.
■
Dynamic: For projecting in a bright room (brightest mode).
■
Dark Wall: For projecting on a dark wall or chalkboard.
■
Living Room: For projecting black-and-white images in a bright
room.
■
Photo: For vivid, high-contrast still images in a bright room (only
available when the source is set to Computer or USB, or
Slideshow).
■
sRGB: Matches the color palette of standard sRGB computer
displays.
■
Sports: For vivid TV images in a bright room (only available for
component video, S-Video, composite video, or HDMI sources).
Displaying and Adjusting the Image 43
Resizing Video Images
note
You cannot change the
aspect ratio when displaying
from a computer using the
USB TypeB port or from a
USB device or SD card
using the Slideshow
source.
You can resize your images by changing the aspect (width to height)
ratio (depending on your input signal).
Press the Aspect button on the remote control repeatedly to cycle
through the available options.
Aspect
button
You can also select the Aspect setting from the projector’s Signal
menu. See page 59 for instructions.
Select from one of these Aspect options:
■
Auto (HDMI images only): Automatically sets the best aspect
ratio according to the input signal.
■
Normal (for images sent through the Computer (Component
Video) port only): Displays images using the full projection area
and maintains the aspect ratio of the image. Choose this setting to
automatically resize the image and make the best use of the
display area.
■
16:9: Converts the aspect ratio of the image to 16:9. 4:3 ratio
images are elongated horizontally to fit.
■
Zoom: Displays images using the full width of the projection area
and maintains the aspect ratio of the image. The image may be
cut off on the top and bottom depending on its aspect ratio.
■
Full: Displays images using the full width of the projection area,
but does not retain the aspect ratio. 4:3 ratio images are elongated
horizontally.
■
Through: Displays images as is (aspect ratio and resolution are
maintained). Black bands may appear or images may be cut off,
depending on the resolution.
44
Displaying and Adjusting the Image
3
3
Presenting With the Remote
Control
The projector includes a number of tools to enhance your
presentation. All of them can be accessed using the remote control,
which lets you operate the projector from anywhere in the room—up
to 19.7 feet (6 meters) away.
This chapter covers:
■
Using the remote control
■
Controlling the picture and sound
■
Operating your computer with the remote control
■
Presenting a slideshow from a USB device or SD card
45
Using the Remote Control
note
If a button is pressed for
longer than 30 seconds, the
remote control stops
operating to conserve battery
power. When you release the
button, normal operation
resumes.
Using the remote control
under bright fluorescent
lamps or in direct sunlight
may affect projector
response.
Make sure batteries are installed as described on page 78. Follow these
tips for using the remote control:
■
Point the remote control at the front or back of the projector, or
at the screen.
■
Stand within 19.7 feet (6 meters) of the projector.
■
Aim the remote control within 30° to the side of, or 15° above or
below, the remote control receivers on the projector.
Controlling the Picture and Sound
You can use the remote control to temporarily turn off the picture and
sound, freeze the action, zoom in on the picture, and adjust the
volume.
Turning Off the Picture and Sound
Press the A/V Mute button on the remote control or close the
A/V Mute slide on the projector to turn off the image and sound, and
darken your screen. This is useful if you want to temporarily re-direct
your audience’s attention without the distraction of a bright screen.
A/V Mute
button
To turn the image and sound back on, press the button again, or open
the A/V Mute slide.
You can create an image, such as a company logo or picture, to display
on the screen whenever you press the A/V Mute button. See page 66
for more information.
46
Presenting With the Remote Control
You can also set the Lens Cover Timer setting to automatically turn
off the projector after 30 minutes to protect the projector if the
A/V Mute slide is closed for a long time. See page 62 for instructions.
Stopping Action
Press the Freeze button on the remote control to stop the action in
your video or computer image. The image freezes but the sound
continues.
note
To restart the action, press the Freeze button again.
The Freeze function pauses
the image, not the sound.
Because the source continues
to transmit signals, it will
not resume at the same
point.
Freeze
button
Zooming In on Your Image
You can zoom in on a portion of the image using the E-Zoom buttons
on the remote control.
1. Press the E-Zoom + button on the remote control.
You see a crosshair indicating the center of the zoom-in area.
2. Use the arrow buttons to position the crosshair.
note
3. Continue pressing the E-Zoom + button to enlarge the selected
area up to 4 times.
You cannot use the
Progressive feature (see
page 59) while you are using
E-Zoom.
4. While the image is enlarged, you can:
■
Use the arrow buttons to move around the screen.
■
Press the E-Zoom – button to zoom out.
5. Press the ESC button to return the image to its original size.
Presenting With the Remote Control 47
Controlling the Volume
To change the volume, press the or
button on the remote
control or on the projector’s control panel.
note
To temporarily shut off the
sound and picture, press the
A/V Mute button or close
the A/V Mute slide.
Volume
buttons
You can also adjust the volume using the projector’s menu system.
See page 61.
Operating Your Computer With the
Remote Control
note
You can use the remote
control as a wireless mouse
only when projecting from a
source connected to the
projector’s Computer
(Component Video) or
HDMI port.
You may need to select
specific settings on your
computer to use the remote
control as a mouse. See your
computer documentation for
details.
48
You can use the remote control in place of your computer’s mouse so
you won’t have to stand next to the computer to control the
presentation.
If you are not using the projector’s USB TypeB port to display your
presentation, you can use the remote control buttons to do one of the
following:
■
Move through presentation slides using the Page Up or Page
Down buttons
■
Use the buttons as you would a wireless mouse by pressing the
arrow, Enter, and Esc buttons
Before you can use one of these functions, you must connect a USB
cable to the USB TypeB port on the projector (see page 29) and select
the function you want to use (see page 49).
Presenting With the Remote Control
To control presentation slides using the remote control’s Page Up or
Page Down buttons, select Page Up/Down as the USB Type B
setting on the Extended menu (see page 62). Then you can control
your presentation using those buttons.
Page up or down
to change slides
in PowerPoint
Right-click
Left-click
If you want to use the remote control like a wireless mouse, select
Wireless Mouse as the USB Type B setting on the Extended menu
(see page 62). Then you can control your presentation as follows:
■
Use the arrow buttons to move the pointer on the screen.
■
Press the Enter button once to left-click, or twice to double-click.
Press the Esc button to right-click.
■
To drag-and-drop, hold down the Enter button. Then use the
arrow buttons to drag the object. When it’s where you want it,
release the Enter button.
Presenting With the Remote Control 49
Presenting a Slideshow
You can use your projector’s Slideshow feature whenever you insert an
SD card or connect a USB device that contains .JPG image files. This
lets you quickly and easily display individual images, or start a
slideshow of all the images in a folder. You can control your slideshow
using the projector remote control.
note
You can project .JPG files in
resolutions up to
8176 × 6144, with pixel
counts incrementing in
multiples of 8.
If the .JPG file is highly
compressed, your projector
may not be able to display it
correctly.
You cannot project movie
files using the Slideshow
feature.
For an instant PowerPoint presentation, save your PowerPoint slides
in JPEG File Interchange Format (.JPG) and store them in a folder.
Copy that folder to an SD card, USB flash memory drive, or other
USB device. Then connect the device to the projector and make sure
the Slideshow Display order option is set to Name order; see
page 52. Then you can start your presentation, as described below.
You can switch the display from the device displaying the slideshow to
another source using the Search button or one of the specific Source
buttons on the remote control. To return to the Slideshow source,
press Search and select Slideshow, or simply press the Slideshow
button.
Starting a Slideshow
1. Connect a USB device to the projector’s USB TypeA port (see
page 32) or insert a compatible SD card in the SD card slot (see
page 34).
2. If you are connected to another image source, press the
Slideshow button on the remote control to start the Slideshow
program.
50
Presenting With the Remote Control
If you are not connected to another image source, the Slideshow
program appears automatically.
3. If you inserted an SD card and connected a USB device at the
same time, you see a screen like this:
Press the arrow buttons on the remote control to highlight the
device you want to present from, then press the Enter button.
4. If you need to select a subfolder on your device, press the arrow
buttons to highlight the folder and press Enter.
5. To display an individual image, press the arrow buttons to
highlight it and press Enter. To display additional image files,
press the l or r arrow button.
note
To rotate a displayed image,
press the u or d button on
the remote control until it is
displayed correctly.
Presenting With the Remote Control 51
note
To display a slideshow from
a folder that is not open,
highlight the folder and press
the Esc button on the
remote control. Then select
Slideshow from the menu
that appears and press
Enter.
To begin a slideshow from a
particular image, use the
arrow buttons to highlight
that image, press Enter,
then press Enter again.
6. To display a slideshow of all the images in the current folder, use
the arrow buttons to highlight Slideshow on the bottom of the
Slideshow screen and press Enter. The images display sequentially
one time through. At the end, you see the folder display again.
Select the following as necessary to control your display or slideshow:
■
■
To move back up a folder level, highlight Back to Top at the top
of the Slideshow screen and press Enter.
To select a different device to display from, highlight Select
drive, press Enter, and select the device.
■
If all the images in a folder do not fit on the Slideshow screen,
highlight Next page and press Enter to display the next screen
full of images (or select Previous page to select the previous
screen).
■
To exit the slideshow, press Esc, select Exit, and press Enter.
Selecting Slideshow Display Options
To select slideshow options or add special effects, follow these steps:
1. Highlight Option at the bottom of the slideshow screen and press
Enter. You see this screen:
52
Presenting With the Remote Control
2. Highlight the options you want to use, and press Enter.
Option
Available settings
Display
order
Name order displays files in name order
Date order displays files in date order
Sort order
In Ascending sorts the files first to last
In Descending sorts the files last to first
Continuous
play
On displays a slideshow continuously
Off displays a slideshow one time through
Screen
switching
time
No does not switch file display automatically
1Sec. to 60Sec. displays files for the selected time
and switches them automatically
Effect
Wipe transitions between images with a wipe effect
Dissolve transitions between images with a dissolve
effect
Random transitions between images using a variety
of effects in random order
3. When you are finished, highlight OK at the bottom of the screen
and press Enter. (Highlight Cancel and press Enter to cancel
your changes.)
Presenting With the Remote Control 53
54
Presenting With the Remote Control
4
4
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image,
sound, and other features. This chapter covers the following
information:
■
Using the menu system
■
Adjusting the image
■
Adjusting signal settings
■
Customizing projector features
■
Customizing power and operation
■
Using the projector security features
55
Using the Menu System
You can use the remote control or the projector’s control panel to
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the Menu button on the
remote control or on the projector. You see a menu screen similar
to the one below:
Options
Menu list
The menus are listed on the left and the options available for the
highlighted menu are shown on the right.
2. Use the arrow buttons on the remote control or the projector to
scroll through the menu list. When you’ve highlighted the desired
menu, press the Enter button to select it.
3. Once you’ve selected the menu, use the arrow buttons to scroll
through the list of options. (Some of the options may be grayed
out or unavailable, depending on the selected source.)
4. After highlighting the option you want to adjust, use the arrow
buttons to change the setting. In some cases, you may have to
press the Enter button to view a sub-screen.
■
Press the left or right arrow button to adjust a slider bar.
■
To select from two or more settings, press the up or down
arrow button to highlight the setting and press Enter.
5. After changing the settings, press the Esc button to save your
changes and return to the previous menu (or press it again to exit
the menu system). You can also press the Menu button to exit.
56
Fine-Tuning the Projector
Restoring the Default Settings
You can use the Reset option on any menu to restore the
factory-default settings for the settings in that menu.
To restore all the projector settings to their factory-default values,
select the Reset menu, highlight Reset All, press Enter, and select
Yes to confirm.
note
When you select Reset All
in the Reset menu, it does
not reset the Input Signal,
User’s Logo, Language, or
Lamp Hours settings.
Adjusting the Image
You can use the Image menu to adjust the brightness, sharpness, color,
tint, contrast, and Auto Iris settings.
1. Press the Menu button on the projector or remote control and
select the Image menu. You see a screen similar to one of these:
Computer/RGB video
note
If you are using the HDMI
port, you see the menu on
the left if the current signal
is digital RGB video, or the
menu on the right if the
signal is component video.
Component video/
Composite video/
S-Video
Fine-Tuning the Projector 57
note
2. Adjust the desired options as needed:
The available settings vary
depending on the input
source selected.
The Brightness setting
changes the opacity of the
projector’s LCD panels. You
can also change the lamp’s
brightness. Select
Brightness Control in the
Settings menu, then choose
High or Low (the default
setting is High).
■
Color Mode
Lets you quickly adjust the color and brightness for various
environments. You can save a different setting for each
source. See page 43 for a description of each color mode.
■
Brightness
Lightens or darkens the overall image.
■
Contrast
Adjusts the difference between light and dark areas.
■
Color Saturation
Adjusts the color depth of the image.
■
Tint
Adjusts the balance of green to magenta in the image.
■
Sharpness
Adjusts the sharpness of the image.
■
Color Temp.
Sets the color temperature of the image. Select High to tint
the image bluer or Low to tint it redder (default setting is
Medium). (Not available if sRGB is selected as the Color
Mode setting.)
■
Color Adjustment
Adjusts the color values. Select Red, Green, Blue to adjust
red, green, and blue hue and saturation values. (Not available
if sRGB is selected as the Color Mode setting.)
■
Auto Iris
Automatically adjusts the projected luminance according to
the brightness of the image. (Available only when Game or
Theater is selected as the Color Mode for the current input
source.)
58
Fine-Tuning the Projector
Adjusting Signal Settings
Although the projector normally detects and optimizes the input
signal automatically, you can use the Signal menu to make manual
adjustments. In addition to changing the position of the projected
image, you can correct tracking and sync for computer images, or
change the aspect ratio.
1. Press the Menu button and select the Signal menu. You see a
screen similar to one of those below. (The settings will be different
depending on the source you are projecting from.)
Computer/RGB video
Component video
Composite video/S-Video
HDMI
2. Adjust the desired options as needed:
■
Auto Setup
Leave this setting On to automatically optimize computer
images. Turn it off if you want to save adjustments you have
made to the Tracking, Sync, and Position settings.
■
Resolution
Set to Auto to have the projector automatically identify the
resolution of the input signal. If necessary, select Wide (for
widescreen images) or Normal (for 4:3 ratio images).
Fine-Tuning the Projector 59
■
note
You can also use the remote
control’s Auto button to
automatically reset the
projector’s Tracking, Sync,
and Position settings. See
page 89 for details.
Tracking
Adjust this value to eliminate vertical stripes in computer
images.
■
Sync
Adjust this value if computer images appear blurry or flicker.
■
Position
If the image is slightly cut off on one or more sides, it may not
be centered exactly. Select this setting and use the arrow
buttons to center it.
■
note
You can adjust the
Progressive setting for
signals from the HDMI
input port (excluding digital
RGB) or component video
only when 480i/576i/1080i
signals are being input.
The HDMI Video Range
setting cannot be set for
digital RGB signals.
Progressive
For composite video, S-Video, component video, and certain
signals from the HDMI port only. Turn this setting on to
convert interlaced signals into progressive signals (best for
moving images). Leave the setting Off for still images.
■
HDMI Video Range
When you connect to the HDMI input port, set the
projector’s video range to match the video range setting of
your device.
■
Input Signal
If the colors don’t look right on the Auto setting, select the
setting for the type of equipment you’ve connected to the
Computer (Component Video) port. Choose RGB for a
computer or RGB-video connection, or Auto for a video
player that outputs a component video signal (with
connectors labeled Y/Cb/Cr or Y/Pb/Pr).
■
Video Signal (composite or S-Video signals only)
Select the setting for the type of equipment you’ve connected
to the Video port. Leave this setting at Auto unless you are
using a 60-Hz PAL system (then select PAL60).
■
Aspect
Sets the image’s aspect ratio (ratio of width to height). See
page 44 for more information.
60
Fine-Tuning the Projector
Customizing Projector Features
You can use the Settings menu to lock the buttons on the projector,
adjust audio volume, and customize several other features.
■
Keystone
Adjusts the shape of the image if the projector has been tilted
upward or downward. If you notice that lines or edge look jagged
after adjustment, decrease the Sharpness setting (see page 57).
■
Auto Keystone
Automatically compensates for keystone distortion when the
projector is tilted upward or downward. This feature is available
only when the projector is set for front projection (enabled by
default).
■
Control Panel Lock
Lets you disable all of the buttons on the projector, or all of the
buttons except the Ppower button. See page 68 for more
information.
■
Brightness Control
Lets you select from two levels of brightness. The Low setting
reduces power consumption and projector noise, and extends the
lamp’s operating life.
■
Volume
Raises or lowers the volume of the projector’s speaker.
Fine-Tuning the Projector 61
Customizing Power and Operation
You can use the Extended menu to customize the way the projector
displays images, enable Direct Power On, turn sleep mode on or off,
and customize other projector operations.
■
Display
Messages: Lets you turn screen messages on or off.
Display Background: Sets the screen background to Black,
Blue, or Logo when no image signal is available.
Startup Screen: Enables or disables display of the startup (User’s
Logo) screen when the projector is turned on.
A/V Mute: Sets the screen background to Black, Blue, or Logo
when the A/V Mute button is pressed.
note
If you hold down the A/V
Mute button on the remote
control for about five
seconds, you switch between
Front and Front/Ceiling
or Rear and Rear/Ceiling.
If Direct Power On is
enabled, the power cord is
connected, and a power
outage occurs, the projector
will start when the power is
restored.
62
■
User’s Logo
Create a custom startup screen, as described on page 66.
■
Projection
Select Front (to project from the front of a screen), Front/Ceiling
(when the projector is mounted upside-down from the ceiling),
Rear (to project from behind onto a transparent screen), or
Rear/Ceiling (to project from behind when the projector is
mounted upside-down from the ceiling).
■
Fine-Tuning the Projector
Operation
Direct Power On: Enable if you want to be able to start the
projector when you connect the power cord (without pressing the
Ppower button).
Sleep Mode: Enable if you want the projector to turn off
automatically if it is idle and no signal is received for 1 to 30
minutes (you can adjust the amount of time using the next
setting).
Sleep Mode Timer: When Sleep Mode is on, you can set the
period of time before the projector turns off automatically, from
1 to 30 minutes.
Lens Cover Timer: Enabled by default to turn the projector’s
power off automatically when the A/V Mute slide is closed for
more than 30 minutes.
note
High Altitude Mode: Enable when you are using the projector
above 4,900 feet (1,500 meters) to ensure that the temperature is
regulated properly. Turn this setting off for lower elevations.
■
Do not use the projector at
altitudes above 7,500 feet
(2,286 meters).
USB Type B
Select how you want to use the USB TypeB port. Select USB
Display to use the USB port to project computer images. Select
Page Up/Down to use the remote control to advance PowerPoint
slides. Select Wireless Mouse to use the remote control buttons
like a wireless mouse. See page 48 for restrictions and details.
■
Language
Select a language to use for the projector menus.
Using the Projector Security Features
To prevent unauthorized use of the projector, you can:
■
Assign a password. You can use the password to prevent the
projector from being turned on and prevent your custom startup
screen from being changed. See the next section.
■
Create a custom screen that is displayed at startup and/or when
the A/V Mute button is pressed. The screen can be locked with a
password to discourage theft and provides a way to identify the
projector should it be stolen. See page 66.
Fine-Tuning the Projector 63
caution
If you lose the remote
control, you will not be able
to enter the password. Keep
the remote control in a safe
place at all times. Also, it’s a
good idea to write down
your password.
■
Disable the projector’s buttons; this is useful, for example, in a
classroom when you want to ensure that no one touches the
projector’s buttons while you’re using the remote control. See
page 68.
■
Secure the projector to prevent theft using a cable locking system.
See page 69.
Enabling Password Protection
The default setting for the password is 0000. Follow these steps to
create a new password:
1. Press the Freeze button on the remote control for five to seven
seconds. You see this screen:
2. Select the type(s) of password protection you want to use:
■
Power On Protect: Prevents unauthorized use of the
projector. After the projector is plugged in and turned on,
you must enter a password to use the projector. Select On,
press Enter, then press Esc to return to the Password Protect
screen.
■
User’s Logo Protect: Prevents your custom screen (see
page 66), display, and User’s Logo settings in the Extended
menu from being changed. Select On, press Enter, then press
Esc to return to the Password Protect screen.
3. Use the arrow buttons to select Password and press Enter.
4. When you see a message asking if you want to change the
password, select Yes and press Enter.
64
Fine-Tuning the Projector
5. Hold down the Num button and use the numeric keypad to enter
a four digit password.
Hold down
6. When you see a confirmation message, reenter the password.
7. Press the Menu button, then press Enter to exit the screen.
8. Turn off and unplug the projector.
Starting the Projector With a Password
When the password function is enabled, you see this screen when you
plug in and turn on the projector:
note
If you leave the projector
plugged in, the Password
screen will not appear. It
appears only if you unplug
and reconnect the power
cord.
Hold down the Num button and use the numeric keypad to enter the
four digit password.
Hold down
The password screen closes and projection begins.
Fine-Tuning the Projector 65
If projection does not begin, check the following:
■
If the password is not correct, you see a message prompting you to
re-enter the password. If you enter an incorrect password three
times in succession, you see an error code with the message The
projector’s operation will be locked and the projector switches
to standby mode. Write down the error code, then disconnect the
projector’s power cord from the electrical outlet, reconnect it, and
turn the projector back on. Try entering the correct password
again.
■
If you have forgotten the password, contact Epson with the
request code number that appears in the Password screen for
assistance. See “Where To Get Help” on page 92.
■
If you enter an incorrect password 30 times in succession, the
projector remains locked and you must contact Epson to arrange
for service.
Creating Your Own Startup Screen
You can transfer any image from your computer or video source to the
projector and then use it as your startup screen. You can also use it as
the screen displayed when the projector is not receiving a signal or
when you press the A/V Mute button. The image can be a company
logo, slogan, photograph, or any other image you want to use.
66
Fine-Tuning the Projector
Capturing the Image
Start by displaying the image you want to use from either a computer
or video source, such as a DVD player or digital camera. Then follow
these steps to capture the image and transfer it to the projector:
1. Press the Menu button on the remote control, highlight the
Extended menu, and press Enter.
note
When you choose an image
for the user’s logo, it erases
any previously used image.
You can save an image up to
300 × 400 pixels in size.
Once you have saved a new
user’s logo, you cannot
return to the factory default
logo.
2. Highlight User’s Logo and press Enter.
3. When you see a message asking Choose this image as the
User’s Logo?, select Yes and press Enter. A selection box
displays over the image.
4. Use the arrow buttons to select the area of the image you want to
use. Then press Enter.
5. When you see the message Select this image?, highlight Yes
and press Enter.
6. Use the arrow buttons to select a zoom factor (display size) and
press Enter.
7. When the message Save this image as the User’s Logo?
appears, select Yes and press Enter. Saving the logo may take a
few moments. Do not use your projector, remote control, or
video source while the logo is being saved.
8. When you see the message Completed, press Menu to exit.
Fine-Tuning the Projector 67
Choosing When to Display the Image
After your image is saved, you can set it to display as the startup
screen, the screen you see when there’s no signal, or the screen you see
when you press the A/V Mute button (see page 46).
1. Press the Menu button, highlight the Extended menu, and press
Enter.
2. Select Display and press Enter.
3. Choose from these display options:
note
You can lock these settings to
prevent them from being
changed without a password
(see page 64).
■
Set Display Background to Logo to display your image
when there is no signal.
■
Set Startup Screen to On to display your image when the
projector is warming up.
■
Set A/V Mute to Logo to display your image when you press
the A/V Mute button.
4. When you’re finished, press Menu to exit.
Disabling the Projector’s Buttons
When you enable the Control Panel Lock function, you can lock all of
the projector’s buttons, or all of the buttons except the Ppower
button. The remote control can still be used to operate the projector.
1. Press the Menu button, highlight the Settings menu, and press
Enter.
2. Select Control Panel Lock and press the Enter button.
3. Select Full Lock (to lock all projector buttons) or Partial Lock (to
lock all buttons except the Ppower button) and press Enter.
4. Select Yes and press Enter to confirm the setting.
68
Fine-Tuning the Projector
5. Press the Menu button to exit.
To disable the Control Panel Lock function, select Off in the Control
Panel Lock menu. Or press and hold the Enter button on the
projector’s control panel for seven seconds. A message is displayed and
the lock is released.
Using Security Locking
The projector includes two security locking points to prevent its theft
when installed or used in public locations:
■
Security cable attachment. You can attach a commercially
available security cable as shown below to secure the projector to a
table or ceiling mount.
Kensington
security slot
■
Security cable
attachment
Kensington security slot. The security slot (located on the side
of the projector) is compatible with the MicroSaver security
systems manufactured by Kensington. You can purchase this lock
from Epson (see page 15).
Fine-Tuning the Projector 69
70
Fine-Tuning the Projector
5
5
Maintaining the Projector
Y
our projector needs little maintenance. All you have to do on a
regular basis is clean the lens, and check that the air filter and vents are
clean. A clogged air filter or vent can block ventilation needed to cool
the projector.
warning
Before you clean any part of
the projector, turn it off and
unplug the power cord.
Never open any cover on the
projector, except the lamp
cover. Dangerous electrical
voltages in the projector can
injure you severely. Do not
try to service this product
yourself, except as specifically
explained in this User’s
Guide. Refer all other
servicing to qualified service
personnel.
The only parts you should replace are the lamp and air filter. If any
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■
Cleaning the lens
■
Cleaning the projector case
■
Cleaning the air filter
■
Replacing the air filter
■
Replacing the lamp
■
Replacing the remote control batteries
■
Transporting the projector
71
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
caution
To remove dirt or smears on the lens, use a commercially available
cloth for cleaning glasses.
Do not rub the lens with
harsh materials or subject
the lens to shocks, or you
may damage it.
Cleaning the Projector Case
Do not use wax, alcohol,
benzene, paint thinner, or
other chemical detergents.
These can damage the case.
Before cleaning, turn off the projector and unplug the power cord.
■
To remove dirt or dust, wipe the case with a soft, dry, lint-free
cloth.
■
To remove stubborn dirt or stains, moisten a soft cloth with water
and a neutral detergent and firmly wring the cloth dry. Then wipe
the case.
Cleaning the Air Filter
note
To order replacement air
filters, request part number
V13H134A13. See page 15
for ordering information.
Your projector includes an air filter to ensure the best performance. If
dust collects on the air filter, clean it as described here. Dust clogs
prevent proper ventilation and can cause overheating, which can
damage the projector.
1. Turn off the projector and unplug the power cord.
2. Remove dust from the air filter using a small vacuum cleaner
designed for computer or office equipment, or gently clean the
vent with a soft brush (such as an artist’s paintbrush).
72
Maintaining the Projector
You can remove the air filter to clean both sides
If the filter is too dirty or broken, replace the filter as described below.
Replacing the Air Filter
You need to replace the air filter if:
■
You cannot remove the dust from it
■
The air filter is damaged or torn
■
You repeatedly see a projected message telling you to clean or
replace it
Contact your dealer or call Epson at 800-GO-EPSON
(800-463-7766) to obtain a new air filter. Request part number
V13H134A13.
1. Turn off the projector and unplug the power cord.
2. Slide the air filter out of its slot as shown.
note
Air filters contain
polycarbonate, ABS resin,
and polyurethane foam.
Dispose of used air filters
according to local
regulations.
3. Slide the new air filter into the slot until it clicks into place.
Maintaining the Projector 73
Replacing the Lamp
note
Turn off this product when
not in use to prolong the life
of the projector.
The life span of the projection lamp is about 3000 hours if
Brightness Control in the Settings menu is set to High (default), and
4000 hours if Brightness Control is set to Low. See page 77 to check
the lamp usage.
It is time to replace the lamp when:
warning
Let the lamp cool fully
before replacing it.
■
The projected image gets darker or starts to deteriorate.
■
The message Replace the lamp appears on the screen and the
Lamp light flashes orange. To maintain projector brightness
and image quality, replace the lamp as soon as possible.
You may also need to replace the lamp if the
stays on red. See page 83.
In the unlikely event that
the lamp has broken, small
glass fragments may be
present and should be
removed carefully to avoid
injury. If the projector has
been installed on the ceiling,
you should stand to the side
of the lamp cover, not
underneath it.
If the lamp is used after the
replacement period has
passed, the possibility that
the lamp may break
increases. When a lamp
replacement message
appears, replace the lamp
with a new one as soon as
possible, even if it is still
working.
74
Lamp light flashes or
Lamp light
Contact your dealer or call Epson at 800-GO-EPSON
(800-463-7766). Request part number V13H010L41.
Follow these steps to replace the lamp:
1. Turn off the projector and, after the projector beeps twice, unplug
the power cord.
2. Let the projector cool for at least an hour (if it has been on). The
lamp is extremely hot immediately after use.
Maintaining the Projector
3. Loosen the lamp cover screw (you cannot remove it). Then slide
the lamp cover off.
4. Loosen the two screws holding the lamp in place (you can’t
remove them).
Loosen, but don’t
remove these screws
note
5. Hold the lamp as shown and pull it straight out.
The lamp(s) in this
product contain mercury.
Please consult your state and
local regulations regarding
disposal or recycling. Do not
put in the trash.
Maintaining the Projector 75
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is
facing the right way.) Then tighten its screws.
7. Replace the lamp cover, then tighten its screw.
note
Tighten the lamp cover
securely so you do not receive
a lamp cover error when you
turn the projector back on.
8. Reset the lamp timer as described in the next section.
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the
projector’s menu system.
note
Do not reset the lamp timer
if you have not replaced the
lamp. Otherwise, you will
receive incorrect lamp usage
information on the Info
menu; see page 77.
76
1. Press the Menu button on the remote control or on the
projector’s control panel. You see the main menu.
Maintaining the Projector
2. Select the Reset menu and press Enter. You see this screen:
3. Select Reset Lamp Hours and press Enter.
4. When you see the prompt, select Yes and press Enter.
5. When you’re finished, press Menu to exit.
Checking Lamp Usage
To check the number of hours the lamp has been used, press the
Menu button and highlight the Info menu. You see a screen like this:
note
The information displayed
depends on the input signal
currently selected.
If you have used the
projector for less than
10 hours, the hours are
listed as 0H.
The life span of the lamp is about 3000 hours if the Brightness
Control setting in the Settings menu is set to High (default), and
4000 hours if the Brightness Control setting is set to Low. Make
sure you have a spare lamp handy if the usage hours on this menu are
close to the life span of your lamp.
Maintaining the Projector 77
Replacing the Remote Control Batteries
caution
Replace the batteries in the remote control as described below:
When replacing batteries,
take the following
precautions:
1. Turn the remote control over.
2. Press in on the catch on the battery cover as you lift the cover off.
■
Replace the batteries as
soon as they run out. If the
batteries leak, wipe away
battery fluid with a soft
cloth. If fluid gets on your
hands, wash immediately.
■
Do not expose batteries to
heat or flame.
■
Dispose of used batteries
according to local
regulations.
3. Install two AA alkaline batteries, inserting the + and – ends as
shown.
■
Do not use batteries other
than those specified in this
User’s Guide and do not
use batteries of different
types or mix old and new
batteries.
■
Keep these batteries out of
the reach of children.
Batteries are choking
hazards and are very
dangerous if swallowed.
78
4. Replace the battery cover and press it down until it clicks into
place.
Maintaining the Projector
Transporting the Projector
The projector contains many glass and precision parts. When
hand-carrying the projector, use an optional carrying case.
note
Follow these guidelines to prevent damage when transporting it:
■
When shipping the projector for repairs, use the original
packaging material if possible. If you do not have the original
packaging, use equivalent materials, placing plenty of cushioning
around the projector.
■
When transporting the projector a long distance, first place it in a
hard-shell shipping case, then pack it in a firm box with
cushioning around the case.
■
Close the A/V Mute slide (lens cover).
■
If an SD card is installed or a USB device is connected, remove it
from the projector.
■
Return the projector feet to their stored (highest) positions.
Epson shall not be liable for
any damages incurred
during transportation.
Maintaining the Projector 79
80
Maintaining the Projector
6
6
Solving Problems
This chapter helps you solve problems with your projector and tells
you how to contact technical support for problems you can’t solve
yourself. The following information is included:
■
Using the projector’s on-screen help system
■
What to do when the projector’s status lights come on or flash
■
Solving projector operation problems
■
Solving problems with the image or sound
■
Solving problems with the remote control
■
Contacting technical support
81
Using On-Screen Help
If the image doesn’t look right or your audio isn’t working, you can
get help by pressing the ? Help button on the projector or the remote
control.
1. Press the ? Help button on the remote control or on the
projector.
You see the Help menu:
2. Use the arrow buttons on the remote control or the projector to
highlight menu items.
3. Press the Enter button on the remote control or the projector to
select the menu item and read the solutions.
4. To exit the help system, press the ? Help button.
If none of the suggestions solve your problem, see additional solutions
to problems in the following sections.
82
Solving Problems
Checking Projector Status
If your projector isn’t working correctly, first turn it off and unplug it.
Then plug the power cord back in and turn on the projector. If this
doesn’t solve the problem, check the lights on top of the projector.
What To Do When the Lights Come On or Flash
The lights on top of the projector indicate the projector’s status.
Power light
Lamp light
Temperature
light
Refer to the following tables for a complete description of the
projector’s status lights:
Power light status
P power light status
Description
Flashing green
The projector is warming up. Wait for the image to appear.
Green
The projector is operating normally.
Orange
The projector is in sleep or standby mode. You can unplug it or press the
P power button to turn it on.
Red, flashing red, or
orange
There is a problem with the projector. Check the next table to diagnose the
problem.
Solving Problems 83
Error light(s) status
Error light(s) status
Description
P Green or orange
It’s time to replace the lamp. See page 74 for instructions. If you continue
to use the lamp after the replacement warning, there is an increased
possibility that the lamp may break.
Flashing orange
Off
P Red
Off
Flashing orange
P Red
Off
Red
Rapid cooling is in progress. Although this is not an abnormal condition,
projection will stop automatically if the temperature rises higher. Make sure
there is plenty of space around and under the projector for ventilation, and
that the air filter and vents are clean.
The projector is overheating, which turns the lamp off automatically.
Wait until the projector switches to standby mode (about 5 minutes). Make
sure there is plenty of space around and under the projector for ventilation.
The air filter may be clogged. Clean or replace the air filter as described on
pages 72 to 73.
If you’re using the projector above an altitude of 4,900 feet (1,500 meters),
turn on High Altitude Mode in the Operation menu (see page 62).
If the projector continues to overheat after you clean the air filter, stop
using the projector, disconnect the power cord, and contact Epson for help
as described on page 92.
Warning: Except as specifically explained in this User’s Guide, do not
attempt to service this product yourself.
P Flashing red
Off
The projector has an internal problem. Stop using the projector, disconnect
the power cord, and contact Epson for help, as described on page 92.
Flashing red
P Red
Off
Flashing red
P Red
Flashing red
Off
There is a problem with the fan or temperature sensor. Stop using the
projector, disconnect the power cord, and contact Epson as described on
page 92.
The lamp may be burnt out. First make sure the lamp cover is securely
installed. If that’s not the problem, the air filter may be clogged. Clean or
replace the air filter as described on pages 72 to 73.
If this does not resolve the problem, let the lamp cool and then remove it. If
the lamp is cracked, replace it as described on page 74. If the lamp is not
cracked, reinstall it. If reinstalling doesn’t work, replace the lamp.
If you’re using the projector above an altitude of 4,921 feet (1,500 meters),
turn on High Altitude Mode in the Operation menu (see page 62).
If none of these suggestions resolves the problem, contact Epson as
described on page 92.
84
Solving Problems
Solving Projector Operation Problems
The power doesn’t turn on.
■
If the projector doesn’t turn on when you press the Ppower
button, make sure the power cord is connected to the projector
and plugged into a working electrical outlet.
■
The power cord may be defective. Disconnect the cord from the
outlet and contact Epson as described on page 92.
■
If you’re using the Direct Power On function and you
immediately plug the power cord back in after unplugging it, the
power may not turn back on. Press the Ppower button to turn
the projector back on.
The buttons on the projector don’t work.
If the Control Panel Lock function has been enabled, you can’t use the
buttons on the projector. Try using the remote control instead, or
press and hold the projector’s Enter button for seven seconds to
release the lock (see page 68).
Solving Problems With the Image
or Sound
No image appears on the screen.
■
Check that the Ppower light is green (not flashing) and that the
A/V Mute slide is open. Also press the A/V Mute button on the
remote control to make sure the picture has not been turned off
temporarily.
■
The projector may be in standby or sleep mode. If the Ppower
light is orange, press the Ppower button to turn the projector on.
■
If the power was switched off and then on again, the projector
may be cooling down. Wait until the Ppower light stops flashing
and remains orange; then press the Ppower button again.
Solving Problems 85
■
The attached computer may be in sleep mode or displaying a
black screen saver. Try pressing a key on the computer.
■
If you are projecting from a DVD player or other video source,
make sure you turn it on and press its Play button.
■
If you are projecting from a composite or S-Video video source,
make sure the Video Signal setting is correct (see page 59).
■
You can also try resetting all of the menu settings (see page 57).
You’ve connected a computer and see a blue screen with the
message No Signal displayed.
■
Make sure the cables are connected correctly, as described
beginning on page 29.
■
If you’ve connected a computer and one or more video sources,
you may need to press the Search or Source Search button to
select the correct source. Allow a few seconds for the projector to
sync up after pressing the button.
■
Make sure the power for your connected equipment is turned on.
If you’re using a PC notebook:
■
Hold down the Fn key on the keyboard and press the function
key that lets you display on an external monitor. It may have an
icon such as
, or it may be labelled CRT/LCD. Allow a few
seconds for the projector to sync up after pressing it. Check your
notebook’s manual or online help for details.
On most systems, the
key lets you toggle between the LCD
screen and the projector, or display on both at the same time.
If you connect the notebook while the projector or computer are
already turned on, the function Fn key that changes the
computer’s image signal to external output may not work. Turn
the computer and the projector off and then back on again.
■
86
Solving Problems
Depending on your computer’s video card, you might need to use
the Display utility in the Control Panel to make sure that both the
LCD screen and external monitor port are enabled. See your
computer’s documentation or online help for details.
If you’re using Mac OS X:
1. Open System Preferences.
2. Click Display or Displays.
3. Select VGA Display or Color LCD.
4. Click Arrangement or Arrange.
5. Select Mirror Displays.
The message Not Supported is displayed.
■
Make sure the correct input signal is selected in the Signal menu
(see page 59).
■
Make sure your computer’s resolution and frequency or refresh
rate is supported by the projector (see page 98). If necessary,
change your computer’s settings.
Only part of the computer image is displayed.
■
Press the Auto button on the remote control or the Enter button
on the projector.
■
Make sure the image Position setting is correct in the Signal
menu. See page 60 for more information.
■
Press the Aspect button on the remote control or select the
correct Aspect setting from the Signal menu. See page 44 for
details on the available options.
■
Press the Esc button on the remote control to cancel the E-Zoom
function.
■
Make sure your computer’s resolution setting is correct. See the
compatible video formats listed on page 98.
■
You also may need to modify existing presentation files if you
created them for a different resolution. See your software
documentation for specific information.
■
If you’re projecting a widescreen computer image, adjust the
Resolution setting (see page 59), if necessary.
Solving Problems 87
■
If you’re projecting an image from a computer with dual display
activated, turn dual display off.
The image isn’t square, but keystone-shaped.
If the image isn’t evenly rectangular, adjust its shape as described on
page 41.
The image contains static or noise.
■
If you’re using a computer cable longer than 6 feet (1.8 meters),
or an extension cable, the image quality may be reduced.
■
Keep your computer and video cables away from the power cord
as much as possible to prevent interference.
■
The video signal may be split between the computer and the
projector. If you notice a decline in the projected image quality
when the image is displayed simultaneously on your notebook
computer and the projector, turn off the notebook’s LCD display.
■
Make sure the correct input signal is selected in the Signal menu
(see page 60).
■
If you’re using a composite, S-Video, or component video source
with 480i signals, turn on the Progressive setting on the Signal
menu (see page 60).
■
If you’ve used the Keystone adjustment, you may need to decrease
the Sharpness setting in the Image menu (see page 58).
■
If you’re projecting from a computer, make sure its signal is
compatible with the projector. See page 98.
■
If you’re projecting from a computer, press the Auto button on
the remote control to reset the projector’s Tracking, Sync, and
Position settings
The image is blurry.
88
Solving Problems
■
There may be dirt or smears on the lens. Clean the lens as
described on page 72.
■
Adjust the focus using the focus ring (see page 42).
■
If the projector is angled sharply toward the screen, it may not be
possible to focus the entire image. Move the projector to position
it more directly in front of the screen.
■
Lower the projection angle to reduce the amount of keystone
correction required.
■
Make sure the projector is within the proper range (projection
distance) from the screen (see page 19).
■
Make sure the lens is not fogged by condensation. You may need
to wait before using the projector after moving it from a cold
environment to a warm environment.
■
If you’re projecting from a computer, you may need to adjust the
tracking and sync settings as described in the next section.
You see vertical bands or the image still looks blurry after
trying the solutions in the previous section.
■
■
If you’re projecting from a computer and displaying an image that
contains a lot of fine detail, you may notice vertical bands or some
of the characters may look heavy or blurred. Press the Auto
button on the remote control or the Enter button on the
projector to reset the projector’s Tracking, Sync, and Position
settings.
If further adjustment is needed, you can fine-tune the Tracking
and Sync settings manually using the Signal menu, as described
on page 60.
note
You must be projecting an
image for the Auto button
to have any effect. It works
only with computer images
projected through the
Computer (Component
Video) port.
1. Fill the screen with an image containing fine detail, such as a
pattern to appear as your desktop background, or try
projecting black text on a white background.
2. Adjust the Tracking to eliminate vertical bands.
Solving Problems 89
3. Adjust the Sync setting to increase the image sharpness.
The image is too light or dark, or colors are incorrect.
note
Because of the different
technologies used, your
projected image may not
exactly match the colors on
your notebook or computer
monitor.
■
Press the Color Mode button or select a different Color Mode
option in the Image menu. See page 43 for details on the available
options.
■
If you’re displaying video, adjust the Color Adjustment and
Color Mode settings on the Image menu. You can also try
adjusting the Color Saturation, Color Temp, and Tint settings
on the Image menu.
■
Try adjusting the Brightness and Contrast settings on the Image
menu.
■
Try adjusting the Brightness Control setting (see page 61).
■
Check your computer display settings to correct the color balance.
■
The projector’s lamp may need to be replaced. See page 74 for
instructions.
■
Make sure the correct input signal is selected in the Signal menu
(see page 60).
■
Make sure that all cables are connected to the proper ports and
connected securely.
There is no sound, or the sound is not loud enough.
90
Solving Problems
■
Use the Volume buttons to adjust the volume (see page 48), or
adjust the Volume setting in the Settings menu.
■
Make sure A/V Mute is not enabled. (Press the A/V Mute button
to disable it.)
■
If your presentation includes computer audio, make sure the
volume control on your computer is not turned all the way down
or muted. In Windows, you may be able to check this by clicking
the volume control in your Windows system tray (lower right
corner of the screen). On a Mac, you may be able to adjust the
volume from your menu bar (top right corner of the screen) or via
the volume control function keys.
■
If you’re using a DVD player or other video source, make sure the
cables are connected correctly, as described on page 32.
Solving Problems With the Remote
Control
The projector doesn’t respond to remote control commands.
■
Point the remote control towards the projector’s receiver. Make
sure you are within 19.7 feet (6 meters) of the projector and
within a 30° horizontal angle and a 15° vertical angle from the
projector’s front or back receiver.
■
The remote control’s batteries may not be installed correctly or
may be low on power. To change the batteries, see page 78.
■
Dim the room lights and turn off any fluorescent lights. Make
sure the projector is not in direct sunlight. Strong lighting,
especially fluorescent lights, may affect the projector’s infrared
receivers. Also, turn off any nearby equipment that emits infrared
energy, such as a radiant room heater.
■
If any buttons are held for longer than 30 seconds, the remote
enters sleep mode. Release any button that is held to wake the
remote.
Solving Problems 91
Where To Get Help
Epson provides these technical support services:
Internet Support
Visit Epson’s support website for solutions to common problems. You
can download utilities and documentation, get FAQs and
troubleshooting advice, or e-mail Epson with your questions.
Speak to a Support Representative
To use the Epson PrivateLine Support service, call (800) 637-7661
and enter the PIN on the included Epson PrivateLine Support card.
This is the fastest way of speaking to a live representative, and it’s free.
This service is available 6 AM to 6 PM, Pacific Time, Monday through
Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing one
of these numbers:
■
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday
through Friday.
■
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday
through Friday.
Days and hours of support are subject to change without notice. Toll
or long distance charges may apply.
92
Solving Problems
Before you call for support, please have the following information
ready:
■
Product name (PowerLite Home Cinema 700)
■
Product serial number (located on the projector)
■
Proof of purchase (such as a store receipt) and date of purchase
■
Computer or video configuration
■
Description of the problem
Purchase Supplies and Accessories
You can purchase screens and other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com
(U.S. sales) or www.epson.ca (Canadian sales).
Solving Problems 93
94
Solving Problems
A
A
Technical Specifications
General
Type of display
Epson poly-silicon TFT active matrix
Resolution
(native format)
1280 × 800 pixels (WXGA)
Color reproduction
16.8 million colors
Light output
(brightness)
Contrast ratio
High mode:
White Light Output 2000 lumens
(ISO 21118 standard)
Color Light Output 2000 lumens
Low mode:
White Light Output 1590 lumens
(ISO 21118 standard)
Color Light Output 1590 lumens
2000:1 (with Auto Iris setting turned
on in the Image menu; see page 57)
410:1 (with Auto Iris setting turned off
in the Image menu; see page 57)
Image size
(16:10 image)
27 to 250 inches (69 to 635 cm)
Projection distance
(16:10 image)
33 to 381 inches (84 to 968 cm)
Projection methods
Front, rear, upside-down (ceiling
mount)
Internal sound system
7 W (monaural)
Optical aspect ratio
16:10 (horizontal:vertical)
Zoom ratio
Manual 1:1.2
95
Noise level
28 dB in Low Brightness mode
35 dB in High Brightness mode
Keystone correction
Manual: ±30° vertical
Auto Keystone: 0 to 11° vertical
Projection Lamp
note
Lamp life results will vary
depending upon mode
selected, environmental
conditions, and usage.
Turn off this product when
not in use to prolong the life
of the projector.
Type
UHE (Ultra High Efficiency)
Power consumption
170 W
Lamp life
Approx. 3000 hours (High Brightness
mode)
Approx. 4000 hours (Low Brightness
mode)
Part number
V13H010L41
Remote Control
Range
19.7 feet (6 meters)
Batteries (2)
Alkaline AA
Dimensions
Height
3.6 inches (92 mm), not including feet
Width
12.9 inches (327 mm)
Depth
9.6 inches (245 mm)
Weight
6.2 lb (2.8 kg)
Electrical
96
Technical Specifications
Rated frequency
50/60 Hz AC
Power supply
100 to 240 VAC ±10%, 2.8A to 1.5 A
Power consumption
Operating: 246 W
Standby: 3 W
Environmental
Temperature
Humidity
(non-condensing)
Operating altitude
Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Operating: 20 to 80% RH
0 to 7500 ft (0 to 2286 m);
over 4921 ft (1500 m), enable High
Altitude mode in the Extended menu
(see page 62)
Safety and Approvals
United States
FCC 47CFR Part 15B Class B (DoC)
UL60950-1 First Edition (cTUVus
Mark)
Canada
ICES-003 Class B
CSA C22.2 No. 60950-1
Pixelworks™ DNX™ ICs are used in this projector.
Technical Specifications 97
Compatible Video Formats
These projectors support the high definition video and computer
display formats listed here.
To project images output from a computer, the computer’s video card
must be set at a refresh rate (vertical frequency) that’s compatible with
the projector. Some images are automatically resized using Epson’s
SizeWize™ technology to display in the projector’s native format. The
frequencies of some computers may not allow images to display
correctly; see your computer’s documentation for details.
Computer, component video, composite video, and S-Video
Mode
98
Technical Specifications
Refresh
rate (Hz)
Resolution
VGA EGA
70
640 × 350
VGA—60
VESA—72
VESA—75
VESA—85
60
72
75
85
640 × 480 (640 × 360*)
640 × 480 (640 × 360*)
640 × 480 (640 × 360*)
640 × 480 (640 × 360*)
SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—85
56
60
72
75
85
800 × 600 (800 × 450*)
800 × 600 (800 × 450*)
800 × 600 (800 × 450*)
800 × 600 (800 × 450*)
800 × 600 (800 × 450*)
XGA—60
XGA—70
XGA—75
XGA—85
60
70
75
85
1024 × 768 (1024 × 576*)
1024 × 768 (1024 × 576*)
1024 × 768 (1024 × 576*)
1024 × 768 (1024 × 576*)
SXGA1—70
SXGA1—75
SXGA1—85
SXGA1—100
70
75
85
100
1152 × 864
1152 × 864
1152 × 864
1152 × 864
WXGA—60
WXGA—75
WXGA—85
60
75
85
1280 × 800
1280 × 800
1280 × 800
SXGA2—60
SXGA2—75
SXGA2—85
60
75
85
1280 × 960
1280 × 960
1280 × 960
SXGA3—60
SXGA3—75
SXGA3—85
60
75
85
1280 × 1024
1280 × 1024
1280 × 1024
Computer, component video, composite video, and S-Video
Mode
Refresh
rate (Hz)
Resolution
WXGA1—60
WXGA2—60
60
60
1280 × 768
1360 × 768
WSXGA60
WSXGA75
WSXGA85
60
75
85
1440 × 900
1440 × 900
1440 × 900
SXGA+60
SXGA+75
SXGA+85
60
75
85
1400 × 1050
1400 × 1050
1400 ×1050
UXGA—60
60
1600 × 1200
WSXGA+—60**
60
1680 × 1050
iMAC VGA
iMAC SVGA
iMAC XGA
MAC13
MAC16
MAC19
MAC19-60
MAC21
117
95
75
67
75
75
60
75
640 × 480 (640 × 360*)
800 × 600 (800 × 450*)
1024 × 768 (1024 × 576*)
640 × 480
832 × 624
1024 × 768
1024 × 768
1152 × 870
NTSC
NTSC 4:43
PAL
N-PAL
M-PAL
PAL—60
SECAM
60
60
50
50
60
60
50
720 × 480 (720 × 360*)
720 × 480 (720 × 360*)
720 × 576 (720 × 432*)
720 × 576 (720 × 432*)
720 × 576 (720 × 432*)
720 × 576 (720 × 432*)
720 × 576 (720 × 432*)
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
60
50
60
50
60/50
60/50
720 × 480 (720 × 360*)
720 × 576 (720 × 432*)
720 × 480 (720 × 360*)
720 × 576 (720 × 432*)
1280 × 720
1920 × 1080
* Letterbox signal
** Available only when you select Wide as the Resolution setting
Technical Specifications 99
HDMI signals
Mode
Refresh
rate (Hz)
Resolution
VGA
60
640 × 480 (640 × 360*)
SVGA
60
800 × 600
XGA
60
1024 × 768
SXGA
SXGA
60
60
1280 × 960
1280 × 1024
SXGA+
60
1400 × 1050
UXGA
60
1600 × 1200
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
HDTV (1080p)
60
50
60
50
60/50
60/50
60/50
720 × 480 (720 × 360*)
720 × 576 (720 × 432*)
720 × 480 (720 × 360*)
720 × 576 (720 × 432*)
1280 × 720
1920 × 1080
1920 × 1080
* Letterbox signal
100
Technical Specifications
B
B
Notices
T
his appendix includes safety instructions and other important information
about your projector.
Important Safety Instructions
Follow these safety instructions when setting up and using the projector:
■
Do not look into the lens when the projector is on. The bright light can
damage your eyes.
■
Do not place the projector on an unstable cart, stand, or table.
■
Do not operate the projector on its side, or while tilted to one side.
Do not tilt the projector forward or back at a greater angle than that
specified for keystone correction (see page 96).
■
If the projector is mounted on a ceiling, it should be installed by
qualified technicians using mounting hardware designed for use with
this projector.
■
If you use a ceiling mount and apply adhesives to the mount to prevent
the screws from loosening, or if you use lubricants or oils on the
projector, the projector case may crack and the projector may fall from
its ceiling mount. This could cause serious injury to anyone under the
mount and could damage the projector. When installing or adjusting a
ceiling mount, do not use adhesives to prevent the screws from loosening
and do not use oils or lubricants.
■
Do not stand on the projector or place heavy objects on it.
■
Do not use the projector where it may be exposed to rain, water, or
excessive humidity.
■
Unplug the projector from the wall outlet before cleaning. Use a dry
cloth (or, for stubborn dirt or stains, a moist cloth that has been wrung
dry) for cleaning. Do not use liquid or aerosol cleaners.
■
Never spill liquid of any kind into the projector.
■
Do not use the projector where it may be exposed to excessive dust or
smoke.
101
102
Notices
■
Never push objects of any kind through the cabinet slots.
■
Do not use or store the projector or remote control in a hot location,
such as near a heater, in direct sunlight, or in a closed vehicle.
■
Do not block the slots and openings in the projector case. They provide
ventilation and prevent the projector from overheating. Do not operate
the projector on a sofa, rug, or other soft surface, or set it on top of loose
papers, which could block vents underneath your projector. If you are
setting up the projector near a wall, leave at least 7.9 inches (20 cm) of
space between the wall and the air exhaust vent.
■
Do not operate the projector in a closed-in cabinet unless proper
ventilation is provided.
■
If you are using two or more projectors side-by-side, leave at least 2 feet
(60 cm) of space between the projectors to allow for proper ventilation.
■
You may need to clean the air filter and vent. A clogged air filter or vent
can block ventilation needed to cool the projector.
■
Do not store the projector outdoors for an extended length of time.
■
Do not use the projector outside the required temperature range of
41 to 95 °F (5 to 35 °C). Doing so may cause an unstable display and
could lead to projector damage.
■
Do not store the projector outside the required temperature range of
14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of
time. Doing so may cause damage to the case.
■
Do not touch the plug during an electrical storm. Otherwise, you may
receive an electric shock.
■
Unplug the projector when it will not be used for extended periods.
■
Unplug the projector from the wall outlet and refer servicing to qualified
service personnel under the following conditions: If it does not operate
normally when you follow the operating instructions, or exhibits a
distinct change in performance; If smoke, strange odors, or strange
noises come from the projector; If the power cord or plug is damaged or
frayed; If liquid or foreign objects get inside the projector, or if it has
been exposed to rain or water; If it has been dropped or the housing has
been damaged.
■
Except as specifically explained in this User’s Guide, do not attempt to
service this product yourself. Refer all servicing to qualified personnel.
Opening or removing covers may expose you to dangerous voltages and
other hazards.
■
Never open any covers on the projector except as specifically explained
in this User’s Guide. Never attempt to disassemble or modify the
projector. Refer all repairs to qualified service personnel.
■
Use the type of power source indicated on the projector. Use of a
different power source may result in fire or electric shock. If you are not
sure of the power available, consult your dealer or power company.
■
If you use the projector in a country other than where you purchased it,
use the correct power cord for that country.
■
Do not overload wall outlets, extension cords, or power strips. Do not
insert the plug into a dusty outlet. This can cause fire or electric shock.
■
Take the following precautions when handling the plug: Do not hold
the plug with wet hands. Do not insert the plug into an outlet with dust
present. Insert the plug firmly into the outlet. Do not pull the power
cord when disconnecting the plug; always be sure to hold the plug when
disconnecting it. Failure to comply with these precautions could result
in fire or electric shock.
■
Do not place the projector where the cord can be walked on.
■
The lamp(s) in this product contain mercury. Please consult your
state and local regulations regarding disposal or recycling. Do not put in
the trash.
■
Do not place anything that can become warped or damaged by heat near
the exhaust vents. Do not bring your hands or face close to the vents
while projection is in progress.
■
Before you move the projector, make sure its power is turned off, the
plug is disconnected from the outlet, and all cables are disconnected.
■
Never try to remove the lamp immediately after use because it will be
extremely hot. Before removing the lamp, turn off the power and wait at
least an hour to allow the lamp to cool completely.
■
Do not place the source of an open flame, such as a lit candle, on or near
the projector.
■
Do not modify the power cord. Do not place heavy objects on top of the
power cord or bend, twist, or pull it excessively. Keep the power cord
away from hot electrical appliances.
■
If the lamp breaks, ventilate the room to prevent gases contained in the
lamp from being inhaled or coming in contact with the eyes or mouth.
■
If the projector is mounted overhead and the lamp breaks, be careful to
prevent pieces of glass from falling into your eyes when you open the
lamp cover.
WARNING: The cords included with this product contain chemicals,
including lead, known to the State of California to cause birth defects or
other reproductive harm. Wash hands after handling. (This notice is
provided in accordance with Proposition 65 in Cal. Health & Safety Code
§25249.5 and following.)
Notices 103
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification of this device and may cause
interference levels which exceed the limits established by the FCC for this
equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than
one interface connector, do not leave cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le materiel brouilleur du Canada.
104
Notices
Index
A
C
A/V Mute
button, 46
display settings, 62, 68
A/V Mute slide
closing, 46, 63, 79
opening, 35, 46, 85
Accessories, 15 to 16
Air filter
cleaning, 72 to 73
ordering, 15
replacing, 73
Altitude, 63, 84, 97
Anti-theft device, 15, 19, 69
Aspect ratio, 44, 60, 95
Audio
cable, 32
connecting equipment, 32
controlling volume, 48
problems, troubleshooting, 90 to 91
turning off (using A/V Mute), 46
Auto Iris setting, 58
Auto Keystone setting, 42, 61
Auto Setup setting, 59
Cables
audio, 32
component-to-VGA, 15, 23, 25
composite, 23, 26
HDMI, 24
illustrations, 18
ordering, 15 to 16
security, 69
S-Video, 15, 27
USB, 29 to 30, 32 to 33
VGA, 28, 31
Capturing image, 67
Carrying cases, 16, 79
Ceiling mount, 15, 19 to 22
Cleaning
air filter, 72 to 73
lens, 72
projector case, 72
Color
correcting, 43, 57 to 58
problems, 90
saturation, 58
settings, 58
temperature, 58
Color Mode, 43, 58
Component-to-VGA video cable, 15, 23, 25
Composite video cable, 23, 26
Computer
connecting to, 29 to 31
selecting source, 40
Connecting projector
to audio equipment, 32
to computer, 29 to 31
to digital camera, 32 to 33
to USB device, 32 to 33
to video equipment, 23 to 28
B
Background screen settings, 62, 68
Bands, vertical, 89
Batteries, replacing, 78
Blurry image, 88 to 89
Brightness, 95
Brightness Control setting, 61, 74, 77
Brightness setting, 58
105
Contrast ratio, 95
Contrast setting, 58
Control Panel Lock setting, 61, 68 to 69, 85
Custom screen, see User’s Logo
D
Dark Wall color mode, 43
Default settings, restoring, 57
Digital camera, connecting, 32 to 33
Dimensions, projector, 96
Direct Power On, 37
Distance from projector to screen, 20 to 22, 95
Documentation, 10
DVD player, connecting, 23 to 28
Dynamic color mode, 43
E
Electrical specifications, 96
Environmental specifications, 97
Epson
accessories, 15 to 16
presentation tips, 10
PrivateLine Support, 10
technical support, 10, 92 to 93
warranty, 15
Error status lights, 84
Extended menu, 62 to 63
E-Zoom buttons, 47
F
FCC compliance statement, 104
Feet, projector, 41
Filter, see Air filter
Fn key, notebook, 86
Focusing image, 42
Freeze button, 47
Full aspect setting, 44
G
Game color mode, 43
H
HDMI cable, 24
HDMI Video Range setting, 60
HDTV images, video formats, 100
Height of image, adjusting, 41
Help system, using, 82
Help, Epson, 10, 92 to 93
High Altitude mode, 63, 84, 97
I
Image
adjusting, 40 to 44, 57 to 58
blurry, 88 to 89
capturing and saving in projector, 67
correcting shape, 42, 61, 88
fitting on screen, 59, 87 to 88
height, adjusting, 41
presentation cameras, 16
problems with, 85 to 90
raising, 41
selecting source, 40
shape, correcting, 42
size and projection distance, 20 to 22, 95
turning off (using A/V Mute), 46
turning off temporarily, 46 to 47
zooming, 42, 47
Image menu, 57 to 58
Info menu, 77
Input Signal setting, 25, 28, 31, 60
Input signal, selecting, 40
Installing, projector, 19 to 22
Instant Off, 38
iPod, connecting, 32 to 33
K
Kensington anti-theft device, 15, 19, 69
Keystone correction, 42, 61, 88, 96
106
Index
L
N
Lamp
number of hours used, 77
ordering, 15
replacing, 74 to 77
specifications, 96
status light, 74, 83 to 84
Lamp timer, resetting, 76 to 77
Language setting, 63
Laptop computer
connecting to, 29 to 31
display problems, 85 to 86
selecting source, 40
Lens Cover Timer setting, 47, 63
Lens, cleaning, 72
Light output specifications, 95
Lights, status, 83 to 84
Living Room color mode, 43
Locking
buttons, 68 to 69
projector, 69
Logo, saving on projector, 66 to 68
No Signal message, 86 to 87
Noise level, 96
Normal aspect setting, 44
Not Supported message, 87
Num button, 65
M
Macintosh display problems, 87
Manuals, 10
Menus
changing settings, 56
default settings, restoring, 57
Extended, 62 to 63
Image, 57 to 58
Info, 77
Reset, 57, 77
Settings, 61
Signal, 59 to 60
User’s Logo, 67
Mouse, using remote control as, 48 to 49
O
Optical aspect ratio, 44, 95
Options for projector, 15 to 16
P
Page Up/Down setting, 49, 63
Page Up/Page Down buttons, 48 to 49
Password
protection, 64 to 66
request code, 66
Photo color mode, 43
Picture source, selecting, 40
Picture, see Image
Position setting, 60, 87
Positioning
image, 41
projector, 19 to 22
Power
button, 37
specifications, 96
status light, 37, 83 to 84
PowerPoint, 19, 22, 50, 63
Presentation tips and training, 10
Presenters Online, 10
PrivateLine Support, 10
Problems
color, 90
image, 85 to 90
no signal, 86 to 87
remote control, 91
sound, 90 to 91
using on-screen help, 82
Progressive format, 60
Projection lamp, see Lamp
Projection setting, 62
Index 107
Projector
cleaning, 72
disabling buttons, 68 to 69
distance from screen, 20 to 22, 95
installing, 19 to 22
lamp specifications, 96
options, 15 to 16
password protection, 64 to 66
positioning, 19 to 22
resolution, 95
security features, 63 to 69
specifications, 95 to 97
transporting, 79
troubleshooting, 81 to 93
turning off, 38
turning on, 35 to 37
unpacking, 18
viewing information about, 77
R
Raising image, 41
Rear-screen projection, 19 to 22, 62
Registration, 15
Remote control
A/V Mute button, 46
as wireless mouse, 48 to 49
batteries used, 96
batteries, replacing, 78
correcting color, 43, 57 to 58
E-Zoom buttons, 47
Freeze button, 47
problems, 91
range, 96
Slideshow button, 33, 34, 40
specifications, 96
troubleshooting, 91
using, 46
Replacing lamp, 74 to 77
Request code, password, 66
Resetting lamp timer, 76 to 77
Resetting menu options, 57
Resize image, 44
Resolution, 44, 87, 95
Resolution setting, 59
108
Index
S
Safety
instructions, 101 to 103
specifications, 97
Saturation setting, 58
Screen
distance from projector, 20 to 22, 95
ordering, 15 to 16
startup screen, creating, 66 to 67
Screen image, see Image
Screen, distance from projector, 20 to 22, 95
SD card, inserting, 34 to 35
Security
cables, 69
Control Panel Lock, 68 to 69
identifying logo, 67 to 68
Kensington lock, 15, 69
password protection, 64 to 66
Settings menu, 61
Sharpness setting, 58
Signal menu, 59 to 60
Sleep mode, 38, 63, 83, 85
Slideshow
button, 33, 34, 40
options, 52 to 53
running, 50 to 52
Sound, troubleshooting, 90
Source, selecting, 40
Speaker, specifications, 95
Specifications
brightness, 95
dimensions, 96
electrical, 96
environmental, 97
general, 95
lamp, 96
remote control, 96
resolution, 95
safety, 97
speaker, 95
video formats, 98 to 100
Sports color mode, 43
sRGB color mode, 43
Startup screen
creating, 66 to 68
settings, 68
user’s logo, see User’s Logo
Status lights, 83 to 84
Support, see Technical support
S-Video cable, 15, 27
Switching picture source, 40
Sync, adjusting, 60, 89 to 90
T
Technical support, 10, 92 to 93
Temperature
requirements, 97
status light, 83 to 84
Temperature, color, 58
Theatre color mode, 43
Through aspect setting, 44
Tint setting, 58
Tracking, adjusting, 60, 89 to 90
Transporting projector, 79
Troubleshooting
blank screen, 85 to 86
cut-off image, 87 to 88
distorted image, 42
image and sound problems, 85 to 91
no signal, 86 to 87
projector problems, 81 to 93
remote control problems, 91
tapered image, 42
Turning off picture (using A/V Mute), 46
Turning off projector, 38
U
Unpacking projector, 18
USB
cable, 29 to 30, 32 to 33
connecting external device, 32 to 33
connecting for display, 29 to 30
selecting TypeB port usage, 48, 63
User’s Logo
creating, 67
display settings, 68
V
VCR, connecting, 23 to 28
VGA video cable, 28, 31
Video
cables, 15 to 16, 18, 23
connecting video equipment, 23 to 28
formats, supported, 98 to 100
selecting source, 40
Video Signal setting, 60
Volume, controlling, 48, 61
W
Warning lights, 83 to 84
Warranty, 15
Windows display problems, 86
Wireless Mouse setting, 49, 63
Wireless mouse usage, 48 to 49, 63
Z
Zoom aspect setting, 44
Zoom ratio, 95
Zoom ring, 42
Zooming image, 42, 47
Index 109