WM7
Washing Machine
1 Warnings
Safety instructions
General Safety
• Never place your machine on a carpet
covered floor. Otherwise, lack of airflow
from below of your machine may cause
electrical parts to overheat. This may cause
problems with your washing machine.
• If the power cable or mains plug is
damaged you must call Authorized Service
for repair.
• Fit the drain hose into the discharge
housing securely to prevent any water
leakage and to allow machine to take in
and discharge water as required. It is very
important that the water intake and drain
hoses are not folded, squeezed, or broken
when the appliance is pushed into place
after it is installed or cleaned.
• Your washing machine is designed to
continue operating when the power
restores after a power interruption. The
machine will resume its program when the
power restores. Press the “Start/Pause/
Cancel” button for 3 seconds to cancel the
program (See, Canceling a Program)
• There may be some water in your machine
when you receive it. This is from the quality
control process and is normal. It is not
harmful to your machine.
• Some problems you may encounter may
be caused by the infrastructure. Press
“Start/Pause/Cancel” button for 3 seconds
to cancel the program set in your machine
before calling the authorized service.
First Use
• Carry out your first washing process
without loading your machine and with
detergent under “Cottons 90°C” program.
• Ensure that the cold and hot water
connections are made correctly when
installing your machine.
• If the current fuse or circuit breaker is less
than 16 Amperes, please have a qualified
electrician install a 16 Ampere fuse or
circuit breaker.
• While using with or without a transformer,
do not neglect to have the grounding
installation laid by a qualified electrician.
Our company shall not be liable for any
damages that may arise when the machine
is used on a line without grounding.
• Keep the packaging materials out of reach
of children or dispose them by classifying
according to waste directives.
• This appliance must be connected to
an earthed outlet protected by a fuse of
suitable capacity.
• The supply and draining hoses must
always be securely fastened and remain in
an undamaged state.
• Fit the draining hose to a washbasin or
bathtub securely before starting up your
machine. There may be a risk of being
scalded due to high washing temperatures!
• Never open the loading door or remove the
filter while there is still water in the drum.
• Unplug the machine when it is not in use.
• Never wash down the appliance with a
water hose! There is the risk of electric
shock!
• Never touch the plug with wet hands. Do
not operate the machine if the power cord
or plug is damaged.
• For malfunctions that cannot be solved by
information in the operating manual:
• Turn off the machine, unplug it, turn off
the water tap and contact an authorized
service agent. You may refer to your local
agent or solid waste collection center in
your municipality to learn how to dispose of
your machine.
If there are children in your
house...
• Keep children away from the machine
when it is operating. Do not let them
tamper with the machine.
• Close the loading door when you leave the
area where the machine is located.
Intended use
• This product has been designed for home
use.
• The appliance may only be used for
washing and rinsing of textiles that are
marked accordingly.
2 - EN
2 Installation
Removing packaging
reinforcement
Tilt the machine to remove the packaging
reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Opening the transportation locks
A Transportation safety bolts must be
removed before operating the washing
machine! Otherwise, the machine will be
damaged!
1. Loosen all the bolts with a spanner until
they rotate freely (“C”)
2. Remove transportation safety bolts by
turning them gently.
3. Fit the covers (supplied in the bag with the
Operation Manual) into the holes on the
rear panel. (“P”)
• If you are going to use your double waterinlet machine as a single (cold) water-inlet
unit, you must install the stopper*, supplied
with your machine to the hot water valve.
• If you want to use both water inlets of the
product, you can connect the hot water
hose after removing the stopper and
gasket group from the hot water valve.
* Applies for the products supplied with a blind
stopper group.
• Models with a single water inlet should not
be connected to the hot water tap.
When returning the appliance to its place after
maintenance or cleaning, care should be taken
not to fold, squeeze or block the hoses.
Connecting to the drain
CKeep the transportation safety bolts in
a safe place to reuse when the washing
machine needs to be moved again in the
future.
CNever move the appliance without the
transportation safety bolts properly fixed in
place!
Adjusting the feet
ADo not use any tools to loosen the lock
nuts. Otherwise, they can be damaged.
1. Manually (by hand) loosen the lock nuts on
the feet.
2. Adjust them until the machine stands level
and firmly.
3. Important: Tighten all lock nuts up again.
The water discharge hose can be attached to
the edge of a washbasin or bathtub. The drain
hose should be firmly fitted into the drain as to
not get out of its housing.
Important:
• The end of the drain hose must be directly
connected to the wastewater drain or to
the washbasin.
• The hose should be attached to a height of
at least 40 cm, and 90 cm at most.
• In case the hose is elevated after laying it
on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
laundry may come out wet.
90
Connecting to the water supply.
Important:
• The water supply pressure required to run
the machine must be 1-10 bar (0,1 – 1
MPa).
• Connect the special hoses supplied with
the machine to the water intake valves on
the machine.
• The hose should be pushed into the
drainage for more than 15 cm. If it is too
long you may have it shortened.
• The maximum length of the combined
hoses must not be longer than 3.2 m.
3 - EN
Electrical connection
Connect the machine to an earthed outlet
protected by a fuse of suitable capacity.
Important:
• Connection should comply with national
regulations.
• The voltage and the allowed fuse
protection are specified in the section
“Technical Specifications”.
• The specified voltage must be equal to
your mains voltage.
• Connection via extension cords or multiplugs should not be made.
BA damaged power cable must be replaced
by a qualified electrician.
BThe appliance must not be operated unless
it is repaired! There is the risk of electric
shock!
3 Initial preparations for
washing
Preparing clothes for washing
Laundry items with metal attachments such
as, bras, belt buckles and metal buttons
will damage the machine. Remove metal
attachments or place the items in a clothing
bag, pillow case, or something similar.
• Sort the laundry according to type of fabric,
color, and degree of soiling and permissible
water temperature. Always follow the
advice on the garment labels.
• Place small items like infants’ socks and
nylon stockings, etc. in a laundry bag,
pillow case or something similar. This will
also save your laundry from getting lost.
• Wash “machine washable” or “hand
washable” labeled products only with an
appropriate program.
• Do not wash colors and whites together.
New, dark colored cottons may release a
lot of dye. Wash them separately.
• Use only dyes/color changers and lime
removers suitable for machine wash.
Always follow the instructions on the
packaging.
• Wash trousers and delicate clothes turned
inside out.
Detergents and softeners
Detergent Drawer
The detergent dra wer is composed of three
compartments:
The detergent dispenser may be in two
different types according to the model of your
machine.
– (I) for prewash
– (II) for main wash
- (III) siphon
– ( ) for softener
Detergent, softener and other cleaning
agents
Add detergent and softener before starting the
washing program.
Never open the detergent dispenser drawer
while the washing program is running!
When using a program without pre-wash, no
detergent should be put into the pre-wash
compartment (Compartment no. I).
Detergent quantity
The amount of washing detergent to be used
depends on the amount of laundry, the degree
of soiling and water hardness.
• Do not use amounts exceeding the
quantities recommended on the package
to avoid problems of excessive foam,
poor rinsing, financial savings and finally,
environmental protection.
• Never exceed the (> max <) level marking;
otherwise, the softener will be wasted
without being used.
• Do not use liquid detergent if you want to
wash using the time delay feature.
Correct load capacity
CPlease follow the information in the
"Program Selection Table". Washing
results will degrade when the machine is
overloaded.
Loading door
The door locks during program operation and
the Door Locked Symbol lights up. The door
can be opened when the symbol fades out.
4 - EN
4 Selecting a Program and Operating Your Machine
Control panel
Figure 1
1
2
7
3
5
4
1 - Spin Speed Adjustment Button
2 - Time Delaying Button (+/-)
3 - Temperature Adjustment Button
4 - Start/Pause/Cancel Button
6
8
5 - Auxiliary Function Keys
6 - Program Selection Knob
7 - Display
8 - On/Off Button
Display symbols
7.a
7.b
7.c
7.d
7.e
-
-
-
-
-
Spin Speed Indicator
Temperature Indicator
Spin Symbol
Temperature Symbol
Remaining Time and Delaying Time
Indicator
7.f - Programme Indicator Symbols (prewash/main wash/rinse/softener/spin)
7.g - Economy Symbol
7.h - Time Delaying Symbol
7.i - Door Locked Symbol
7.j - Start Symbol
7.k - Standby Symbol
7.l - Auxiliary Function Symbols
7.m - Water cut-off Symbol (According to
your machine’s model)
Figure 2
F1
F2
F3
F4
The recommended temperature and spin
speed for the selected program appear. Press
“Start/Pause/Cancel” button to start the
program.
CSort the laundry according to type of fabric,
color, degree of soiling and permissible
water temperature when choosing a
Program selection
program.
Turn the Programme Selection Knob to the
Main programs
program mode that you wish to wash your
Depending on the type of textile, the following
laundry.
main programs are available:
5 - EN
Turning the machine on
Plug in your machine. Turn the tap on
completely. Check if the hoses are connected
tightly. Place the laundry in the machine. Add
detergent and softener. Press the “On/Off”
button.
• Cotton
You can wash normally soiled durable cotton
clothes with this program. Your laundry will be
washed with vigorous washing movements
during a longer washing cycle.
• Synthetics
You can wash your less durable clothes on
this program. Lighter washing movements
and shorter washing cycle is used compared
to “Cottons” program. It is recommended for
your synthetic clothes (such as shirts, blouses,
synthetic/cotton blended garments, etc.). For
curtains and lace, the “Synthetic 40” program
with pre-wash and anti-creasing functions
selected is recommended.
• Woollens
You can wash your machine-washable woolen
garments on this program. Wash by selecting
the proper temperature according to the labels
of your clothes. It is recommended to use
appropriate detergents for woolens.
Additional programs
For special cases, there are also extra
programs available:
C Additional programs may differ according
to the model of your machine.
• Babycare
Increased hygiene is provided by a longer
heating period and an additional rinse cycle. It
is recommended for baby clothes and clothes
worn by allergic people.
• Cotton Eco
You can wash normally soiled durable cotton
clothes by saving more energy and water with
this program. Your laundry will be washed with
vigorous washing movements and wash time
is longer than “Cotton” programme.
• Mix 40
This program washes for a longer period
at 40°C and gives the same result as the
“Cottons 60°C” program, thus it saves energy.
It is suitable for clothes for which you cannot
use the “Cottons 60°C” program.
• Delicate
You can wash your delicate clothes on this
program. It has more sensitive washing
movements and does not make intermediate
spinning compared to “Synthetic” program.
• Hand wash
You can wash your woolen/delicate clothes
that bear “not machine- washable” labels for
which hand wash is recommended on this
program. It washes the laundry with very
tender washing movements without damaging
your clothes.
• Daily Xpress
This program is used to wash lightly soiled and
unstained cotton garments in a short time.
• Xpress Super Short
You can use this program to quickly wash a
small number of lightly soiled and unstained
cotton garments. E.g.: bathrobes, duvet
covers, sport wear, daily clothes and etc. used
only once.
• Darkcare
Use this programme to wash your dark
coloured laundry, or the coloured laundry
that you do not want them get faded. This
programme washes your laundry with
low mechanical movements and at low
temperature. We recommend you to use
liquid detergent or woolen shampoo for dark
coloured laundry.
Economy Symbol
Shows energy saving programs and
temperature selections.
As “Intensive” and “Baby” programs are long
programs with higher temperature selections
to ensure hygiene, “Economy” Symbol will not
light up.
Special programs
For specific applications, you can select any of
the following programs:
• Rinse
This program is used when you want to rinse
or starch separately.
• Spin+Drain
This program spins with maximum possible
rpm in the default setting after the water drains
from the machine.
CUse a lower spin speed for delicate
laundries.
Temperature selection
Whenever a new program is selected, the
temperature anticipated for that program
appears on the temperature indicator.
To change the temperature, press the
“Temperature” button. Temperature decreases
in 10° increments.
Cold selection is shown with “-” symbol.
90˚C
60˚C
40˚C
30°C
Cold
Heavily soiled, white cottons and
linens.
Normally soiled, fade proof colored
linens, cottons or synthetic clothes
and lightly soiled white linens
Blended clothes including synthetics
and woolens as well as delicates.
Spin Speed selection
Whenever a new program is selected, the
maximum spin speed of the selected program
is displayed on the spin speed indicator.
To decrease the spin speed, press the “Spin”
button. Spin speed decreases gradually. Then,
6 - EN
rinse hold and no spin options are shown
respectively.
” and no spin is
Rinse hold is shown with “
shown with “ ” symbols.
If you do not want to unload your clothes
immediately after the program, you may use
the rinse hold function in order to prevent your
clothes become wrinkled in an anhydrous
condition. With this function, your laundry is
kept in the final rinsing water. If you want to
spin your laundry after the rinse hold function:
- Adjust the spin speed.
- Press “Start/Pause/Cancel” button.
Program resumes. Your machine drains the
water and spins your laundry.
You can use no spin function in order to drain
the water without spinning at the end of the
program.
Program selection and consumption table
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Selectable
temperature range
°C
•
•
•
Rinse Hold
1600
1600
1600
1600
1600
1000
1000
1000
1000
1000
1000
1400
1400
1400
1400
Anti-Creasing
2.20
1.50
0.85
1.06
2.20
1.00
0.50
0.55
0.50
0.30
0.20
0.10
2.00
1.20
0.25
Rinse Plus
Spin Speed
(rpm)***
62
60
60
60
65
50
45
45
80
40
30
30
60
60
70
Quick Wash
Energy
Consumption
(kWh)
90
7
60
7
40
7
60** 7
90
7
60
3
40
3
40
3.5
40
3
40
1.5
30
1
30
2
90
7
60
7
30
7
Water
Consumption (l)
Max. Load (kg)
Cotton
Cotton
Cotton
Cotton Eco
Babycare
Synthetics
Synthetics
Mix
Darkcare
Woollen
Hand wash
Xpress Super Short
Daily Xpress
Daily Xpress
Daily Xpress
Prewash
Auxiliary functions Temperature
2
EN
90-Cold
90-Cold
90-Cold
60
90-30
60-Cold
60-Cold
40-Cold
40-Cold
40-Cold
30-Cold
30-Cold
90-Cold
90-Cold
90-Cold
** Energy & Water labelling test programme according to AS/NZS 2040.1
• Selectable
* Automatically selected, not cancelable.
*** If maximum spin speed of your machine is lower, selection may be made until maximum spin
speed.
Water and power consumption and programme duration may differ from the table shown,
subject to changes in water pressure, water hardness and temperature, ambient temperature,
type and amount of laundry, selection of auxiliary functions, and fluctuations in the supply
voltage.
CThe auxiliary functions in the table may differ according to the model of your machine.
CProgramme duration will be displayed on the screen of your machine according to your
selection.
7 - EN
Auxiliary functions
Auxiliary Function Selection Buttons
CSelect the required auxiliary functions
before starting the program.
CSome combinations cannot be selected
together. (Ex.: Pre-wash) (Figure 1-5a) and
Quick Wash (Figure 1-5b).
Auxiliary function selection
If an auxiliary function that should not be
selected together with a previously selected
function is chosen, the first selected function
will be cancelled and the last auxiliary function
selection will remain active.
(Ex.: If you want to select pre-wash first and
then quick wash, pre-wash will be cancelled
and quick wash will remain active.
Auxiliary function that is not compatible
with the program cannot be selected. (see,
“Program Selection Table”)
• Prewash
When you select this function (5a), the display
will indicate “1” symbol. A pre-wash is only
worthwhile for heavily soiled laundry. Without
pre-wash you save energy, water, detergent
and time. Pre-wash without detergent is
recommended for lace and curtains.
• Quick Wash
With this function (5b), the wash time is
shortened. The “2” symbol will light up on the
display. Use this function for smaller amounts
or slightly soiled laundries.
• Rinse Plus
This function (5c) allows your machine to
perform an extra rinsing in addition to the
rinsing cycles performed by your machine after
main washing cycle. Thus, the risk for sensitive
skins (babies, allergic skins and etc.) to be
effected by the minimal detergent remnants on
the laundry is reduced. “3” symbol will light up
on the display.
• Anti-Creasing
With this function (5d), drum movement will
be lessened to prevent creasing and spinning
speed is limited. In addition, washing is carried
out at a higher water level. The “4” symbol will
light up on the display.
CWhenever you select this auxiliary function,
load your machine with half of the
maximum laundry specified in the program
table.
Time display
The display shows the time remaining for
the program to complete while a program is
running. Program duration may differ from the
values in the consumption table subject to the
changes in the water pressure, water hardness
and temperature, ambient temperature, type
and amount of laundry, auxiliary functions
selected, and changes in the supply voltage.
Time delay
With the “Time delay” function you can delay
the program start up to 24 hours. Setting can
be made in intervals of 30 minutes.
1. Press “Time delaying” buttons “+” and “-”
to set your desired time delay.
2. Press “Start/Pause/Cancel” button. Then
the time delay starts to count down.
CMore laundry may be loaded or taken out
during the time delay period.
Changing the delay time
If you want to change the time during the
countdown:
1. Press “Start/Pause/Cancel” button.
2. Press “Time delaying” buttons “+” or “-” to
set the desired time delay.
3. Press “Start/Pause/Cancel” button.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program immediately:
1. Press “Start/Pause/Cancel” button.
2. Pres “Time Delaying” “-” button to
decrease the time delay. Program duration
after 30 minutes shall be displayed.
3. Press “Start/Pause/Cancel” button to start
the program.
Starting the Program
1. Press “Start/Pause/Cancel” button to start
the program.
2. The start symbol (Figure 2-7j) which
indicates that the program has started will
light up.
3. The door locks and the door locked
symbol (Figure 2-7i) will light up.
4. The Symbol of the relevant step (prewash,
main wash, rinse, softener and spin) that
the program has started from will light up
(Figure 2-7f).
CIf the machine is not spinning, the
program may be in rinse hold mode or the
automatic spin correction system has been
activated due to an excessive unbalanced
distribution of laundry in the machine.
Changing the selections after the
program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
When the “Program selection” button is
brought to the appropriate position, rpm and
temperature data reappear.
8 - EN
5 Maintenance and cleaning
Switching the machine to standby
mode
Detergent Drawer
Remove any powder residue buildup in the
drawer. To do this;
1. Press the dotted point on the siphon in the
softener compartment and pull towards
you until the compartment is removed from
the machine.
Press “Start/Pause/Cancel” button
momentarily to switch your machine to the
standby mode. Auxiliary functions can be
cancelled or selected in accordance with
the step the program is at. The door can be
opened if the water level is suitable. Laundry
may be added / taken out by opening the
door.
Door lock
The Door Locked Symbol (Figure 2-7i) lights
up when the loading door is locked. This
symbol will flash until the door is allowed to
open. Do not force the door at this stage. You
may open the door after the symbol fades out.
Child-proof lock
This function protects the appliance from
being tampered by children. In this case, all of
the buttons are inactive except On/Off button;
by On/Off button you can whether stop or
resume (while child-lock on) the program of
your machine.
The machine is switched to child-lock by
pressing the 2nd and 4th auxiliary functions
for 3 sec. “C:on” (Child lock is activated) label
appears on the screen. The same symbol
will also be displayed whenever any button is
pressed while the machine is child-locked.
To deactivate the child-proof lock, press the
2nd and 4th auxiliary function buttons for 3
sec. “C:OFF” (Child lock is deactivated) label
appears on the screen.
CIf more than a normal amount of water
and softener mixture starts to gather in the
softener compartment, the siphon must be
cleaned.
2. Wash the dispenser drawer and the
siphon with plenty of lukewarm water in a
washbasin.
3. Replace the drawer into its housing after
cleaning. Check if the siphon is in its
original location.
Inlet water filters
There is a filter at the end of each water intake
valve at the back side of the machine and also
at the end of each water intake hose where
they are connected to the tap. These filters
prevent the foreign substances and dirt in the
water to enter into the machine. Filters should
be cleaned as they get dirty.
• Close the taps.
Ending the program through
canceling
“Start/Pause/Cancel” button is pressed for 3
seconds to cancel the program. Start symbol
(Figure 2-7j) will flash during cancellation. After
cancellation, the symbol of the corresponding
step at which the cancellation was made will
remain lit and “End” will appear on the screen.
End of program
When the program is finished, the symbols
of the relevant steps will remain lit up and
the auxiliary function, spin and temperature
data selected at the start-up of the program
will remain selected. “End” will appear on the
display.
• Remove the nuts of the water intake hoses
to clean the surfaces of the filters on the
water intake valves with an appropriate
brush.
• If the filters are very dirty, you can pull them
out by means of pliers and clean them.
• Take out the filters on the flat ends of
the water intake hoses together with
the gaskets and clean thoroughly under
streaming water.
• Replace the gaskets and filters carefully to
their places and tighten the hose nuts by
hand.
9 - EN
Draining any remaining water and
cleaning the pump filter
Your product is equipped with a filter system
which ensures a cleaner water discharge that
extends pump life by preventing solid items
such as buttons, coins and fabric fibers from
clogging the pump propeller during discharge
of the washing water.
• If your machine fails to drain the water,
the pump filter may be clogged. You may
have to clean it every 2 years or whenever
it is plugged. Water must be drained off to
clean the pump filter.
In addition, water may have to be drained off
completely in the following cases:
• before transporting the machine (e.g. when
moving house)
• when there is the danger of frost
In order to clean the dirty filter and discharge
the water;
1- Unplug the machine to cut off the supply
power.
AThere may be water at 90°C in the
machine. Therefore, the filter must be
cleaned only after the inside water is
cooled down to avoid hazard of scalding.
2- Open the filter cap. The filter cap may be
composed of one or two pieces according to
the model of your machine.
If it is composed of two pieces, press the tab
on the filter cap downwards and pull the piece
out towards yourself.
If it is composed of one piece, hold it from
both sides and open it by pulling out.
3- An emergency drain hose is supplied with
some of our models. Others are not supplied
with this item.
If your product is supplied with an emergency
drain hose, do the following as shown in the
figure below:
by pulling out the plug at the end of the
hose. If the amount of water to be drained
off is greater than the volume of the
container, replace the plug, pour the water
out, then resume the draining process.
• After draining process is completed,
replace the plug into the end of the hose
and fit the hose back into its place.
If your product is not supplied with an
emergency drain hose, do the following as
shown in the figure below:
• Place a large container in front of the filter
to receive water flowing from the filter.
• Loosen pump filter (anticlockwise) until
water starts to flow out of it. Direct the
flowing water into the container you have
placed in front of the filter. You can use a
piece of cloth to absorb any spilled water.
• When there is no water left, turn the pump
filter until it is completely loose and remove
it.
• Clean any residues inside the filter as
well as fibers, if any, around the propeller
region.
• If your product has a water jet feature, be
sure to fit the filter into its housing in the
pump. Never force the filter while replacing
it into its housing. Fit the filter fully into its
housing; otherwise, water may leak from
the filter cap.
4- Close the filter cap.
Close the two-piece filter cap of your product
by pushing the tab on it.
Close the one-piece filter cap of your product
by fitting the tabs on the bottom into their
positions and pushing the upper part of it.
• Pull out the pump outlet hose from its
housing.
• Place a large container at the end of the
hose. Drain the water off into the container
10 - EN
8 Solution suggestions for problems
Cause
Explanation / Suggestion
Programme cannot be started or selected.
Machine may have switched to self protection
Bring your machine to factory settings by turning
mode due to an infrastructure problem (such as the Programme selection knob. (see, Ending the
line voltage, water pressure, etc.).
Programme through Cancelling)
Water in the machine.
There may be some water in your machine
when you receive it. This is from the quality
control process and is normal.
It is not harmful to your machine.
There is water coming from the bottom of the machine.
There might be problems with hoses or the
pump filter.
- Make sure that the seals of the water inlet hoses are
securely fitted.
- Tightly attach the drain hose to the tap.
- Make sure that the pump filter is completely closed.
Machine does not fill with water
- Tap may be turned off.
- Water inlet hose might be bent.
- Water inlet filter might be clogged.
- The loading door may be ajar.
- Open the inlet water taps fully.
- Flatten the water intake hose.
- Clean the water intake filter.
- Close the loading door.
Machine does not discharge water.
- Water outlet hose might be clogged or
twisted.
- Pump filter may be clogged.
- Clean or flatten the hose.
- Clean the pump filter.
Machine vibrates or shakes.
- Machine feet might not be adjusted.
- Transportation safety bolts might have not
been removed.
- There may be a small amount of laundry in the
machine.
- The machine may be overloaded or the
clothes may be distributed unevenly.
- There machine might be touching a solid
surface.
- Adjust the machine feet.
- Remove the transportation safety bolts.
- Add more laundry to the machine.
- Reduce the amount of laundry in the machine or
balance the load by hand.
- Ensure that nothing touches the machine.
Machine stops shortly after the Programme starts.
Machine can stop temporarily due to low
voltage.
It will resume operating when the voltage is back to
the normal level.
The water being taken in is directly discharged.
Improper position of the drain hose.
Connect the water draining hose as described in the
operation manual.
No water can be seen in the machine during washing.
This is not a problem. The water level is not
visible from the outside of the machine.
The door is jammed.
- Water level might be above the lower level of
the door.
- Machine might be heating up the water or it
may be at the spinning cycle.
- Due to an electrical mechanism, the door
can only be opened a few minutes after the
Programme has stopped.
- Run either the “Pump” or “Spin” Programme.
- Wait until the process is over.
- Wait until the process is over.
11 - EN
Machine fills with water when a process is cancelled.
Inside of machine may be hot.
For safety reasons cold water is added to cool the hot
wash load
It continuously spins. Remaining time does not count down. (On models with display)
There may be an imbalance of laundry in the
machine.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- The laundry in the drum may be clustered (bundled
laundry in a bag). Laundry should be rearranged and
re-spun.
- No spinning is performed when the laundry is not
evenly distributed in the drum to prevent any damage
to the machine and to its environment.
Washing time takes longer than the time specified in the manual
- Water pressure may be low.
- Supply voltage may be low.
- Input temperature of water may be low.
- There may be an imbalance of laundry in the
machine.
- Number of rinses and/or amount of rinse
water might have increased.
- The machine will wait until there is sufficient amount
of water, which will lengthen the washing time to avoid
poor washing results due to insufficient water.
- Washing time is extended to avoid poor washing
results when the supply voltage is low.
- Cycle time is extended to heat up the water when
the input water is cold. Also, washing time can be
lengthened to avoid poor washing results.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- The laundry in the drum may be clustered (bundled
laundry in a bag).
- Laundry should be rearranged and re-spun.
- No spinning is performed when the laundry is not
evenly distributed in the drum to prevent any damage
to the machine and to its environment.
- Water amount is increased to obtain a better rinse
and a rinse cycle is added when necessary.
It continuously washes. Remaining time does not count down.
In the case of a paused countdown while taking
in water:
- Timer will not countdown until the machine
is filled with the correct amount of water. (On
models with display)
- Time might have gotten stuck during heating
step. (On models with display)
In the case of a paused countdown at the
spinning step:
There may be an imbalance of laundry in the
machine. (On models with display)
- The machine will wait until there is sufficient amount
of water to avoid poor washing results due to lack of
water. Then the timer will start to count down.
- Time will not count down until the selected
temperature for the Programme is attained.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- The laundry in the drum may be clustered (bundled
laundry in a bag). Laundry should be rearranged and
re-spun.
- No spinning is performed when the laundry is not
evenly distributed in the drum to prevent any damage
to the machine and to its environment.
It did not spin.
- The automatic spin correction system might have
been activated due to the unbalanced distribution of
the laundry in the drum.
- There may be an imbalance of laundry in the
- The laundry in the drum may be clustered (bundled
machine. Therefore, the Programme might have laundry in a bag). Laundry should be rearranged and
been completed without spinning.
re-spun.
- The machine will not spin if the water has not - No spinning is performed when the laundry is not
completely drained.
evenly distributed in the drum to prevent any damage
to the machine and to its environment.
- Check the filter.
- Check the drain hose.
12 - EN
Washing performance is poor: Laundry turns grey
- Using insufficient amount of detergent for a
long time,
- Washing at low temperatures for a long time,
- Using insufficient amount of detergent for
hard waters (soil can stick to the laundry),
- Using excessive amount of detergent
(detergent can stick to the laundry).
- Use the recommended amount of detergent
appropriate for water hardness and the laundry.
- Select the proper temperature for the laundry to be
washed.
- If the water hardness is high, using an insufficient
amount of detergent can cause laundry to turn grey
over time.
- It is difficult to eliminate such greyness once it
occurs.
Washing performance is poor: Stain could not be removed, not cleaned. Laundry could not be
whitened.
- Insufficient amount of detergent used.
- Excessive laundry loaded into machine
- Wrong Programme and temperature might
have been selected.
- Improper detergent may have been used.
- Wrong type of detergent used.
- Use recommended amount of detergent appropriate
for the laundry.
- Do not load the machine in excess.
- Select the proper Programme and temperature for
the laundry to be washed.
- Put the detergent in the correct compartment.
- Do not mix detergent with bleaching agents.
- Washing performance is poor: Oily stains appear on laundry.
- Washing performance is poor: Bad odour
- Oily accumulations on the drum may have
stuck to the laundry.
- Oily accumulations on the drum may have
stuck to the laundry.
- Such odours and bacteria layers are formed on
the drum as a result of continuous washing at lower
temperatures and/or in short Programmes.
- Leave the detergent dispenser drawer as well as the
loading door of the machine ajar after each washing.
Thus, a humid environment favorable for bacteria
cannot be created inside the machine.
- Machine must be operated empty either at 60°C or
90°C Programme with detergent every 6 months.
Colour of the clothes faded.
- Excessive laundry loaded into machine.
- Detergent may have gotten damp.
- A higher temperature might have been
selected.
- Do not load the machine in excess
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- Select the proper Programme and temperature
according to the type and soiling degree of the
laundry.
It does not rinse well.
- The amount, brand and storage conditions of
the detergent used might not be appropriate.
- Detergent might have been put in the wrong
compartment.
- Machine filter may be clogged.
- Drain hose may be folded.
- Intermediate spins may be skipped.
- Store detergent in a closed and dry location. Do not
keep them under high temperatures.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine can
take this detergent during rinsing or softener step.
- Check the filter.
- Check the drain hose.
- There may be an imbalance of laundry in the
machine.
- The laundry in the drum may be clustered (bundled
laundry in a bag). Laundry should be rearranged and
re-spun.
- No spinning is performed when the laundry is not
evenly distributed in the drum to prevent any damage
to the machine and to its environment.
13 - EN
Clothes stiffened.
- Insufficient amount of detergent used.
- The detergent may have been placed into the
wrong compartment; the detergent may be
mixed with the softener.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to become
stiff in time. Use appropriate amount of detergent
according to the water hardness.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine can
take this detergent during rinsing or softener step.
- Do not mix the softener with detergent when putting
in the compartment.
- Wash and clean the drawer with hot water.
Clothes do not smell like the softener.
- Insufficient amount of detergent used.
- The detergent was placed into the wrong
compartment; the detergent was mixed with
the softener.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to become
stiff in time. Use appropriate amount of detergent
according to the water hardness.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine can
take this detergent during rinsing or softener step.
Do not mix the softener with detergent when putting in
the compartment.
Wash and clean the drawer with hot water.
Detergent residue in the dispensing drawer.
- Detergent may have been put in wet
dispenser drawer.
- Detergent may have gotten damp.
- Water pressure might be low
- The detergent in the main wash compartment
might have gotten wet while taking in the
prewash water..
- Detergent might be mixed with the bleaching
agent.
- Dry the detergent drawer before putting in detergent.
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- The detergent dispenser outlet (holes) may have a
problem.
- There might be problems with the detergent
dispenser valves.
- Do not mix the softener with detergent when putting
in the compartment.
There is detergent left on the laundry.
- Excessive laundry loaded into machine.
- Wrong Programme and temperature might
have been selected.
- Wrong detergent may have been used.
- Do not load the machine in excess.
- Select the proper Programme and temperature for
the laundry to be washed.
- Use wool detergents for woollens.
There is too much foam
.
- You may not be using proper detergent for
automatic washing machines.
- Excessive amount of detergent may have been
used.
- Too much detergent may have been used for a
small amount of lightly soiled laundry.
- Detergent may have been stored improperly.
- Type of material being washed (lace items
will cause excessive foam due to their meshed
structure).
- Detergent might have been put in the wrong
compartment.
- Softener being released early.
- Use only automatic washing machine detergents in
your washing machine.
- Use only sufficient amount of detergent.
- Use only sufficient amount of detergent.
- Store detergent in a closed and dry location.
- Do not store in excessively hot places.
- Use smaller amounts of detergent for lace items.
- If you put detergent in the prewash compartment
although you have not selected a prewash cycle, the
machine can take this detergent during rinsing or
softener step.
- Too much softener was put in.
The detergent dispenser is problematic. Water is
siphoned (pulling the softener into the washer early)
during the fill or rinse cycles.
Valves are problematic.
There is foaming over the detergent drawer
Too much detergent was used
Mix 1 tablespoonful softener and ½ liter water
and pour into the main wash compartment of the
detergent drawer.
14 - EN
7 Specifications
WM7
Models
Maximum dry laundry capacity (kg)
7
Height (cm)
84
Width (cm)
60
Depth (cm)
54
Net Weight (±4 kg)
72
Electricity (V/Hz.)
220-240 V / 50Hz
Total Current (A)
10
Total Power (W)
2000-2350
1200
Spinning cycle (rpm max.)
Specifications of this appliance may change without notice to improve the quality of the product.
Figures in this manual are schematic and may not match your product exactly.
Values stated on the machine labels or in the documentation accompanying it are obtained
in laboratory in accordance with the relevant standards. Depending on operational and
environmental conditions of the appliance, values may vary.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment by
dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains
a great amount of recyclable material. It is marked with this label to indicate the used appliances
that should not be mixed with other waste. This way, the appliance recycling organised by your
manufacturer will be done under the best possible conditions, in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your
retailer for the used appliance collection points closest to your home. We thank you doing your part
to protect the environment.
15 - EN
16 - EN
17 - EN
18 - EN
ELECTRICAL DISTRIBRUTORS Service & Care Centre PTY LTD ABN 11 051 297 557 1/9 TERAN CLOSE WHITEBRIDGE NSW 2290 PH: 02 49 209114 FAX: 02 49209115 EMAIL: sales@euromaid.com.au WEBSITE: www.euromaid.com.au EUROMAID WASHING MACHINE WARRANTY IN ADDITIONS TO RIGHTS BY LAW Electrical Distributors Australia Pty Ltd guarantees to the original purchaser in the first two years of ownership that any part with defective material be replaced free of charge, provided that all service work is carried out by Electrical distributors Australia Pty Ltd or the nearest appointed service agent. 2 Year Warranty Products: Front Load washing machines and Dishwashers 1 Year Warranty Products: Clothes dryers Where the appliance is installed outside the normal service area of Electrical Distributors Australia Pty Ltd or its Appointed Service Agent the purchaser will pay the travel cost charges for the service agent to attend the repair or to take the appliance to the service centre. Built In & Free Standing Appliances: Access must be granted within normal working hours and our Service Agents must have easy access to these built in appliances and charges will be the responsibility of the purchaser where the service technician cannot obtain easy access to remove the appliance for inspection prior to repair. This Warranty is not transferable and excludes any repair or replacement caused by Power Surges faulty installation abuse, Pest Damages, misuse, acts of God or accident. The above Warranty is for Domestic Application only and is limited to Three (3) Months in Commercial Applications. AUTHORISED SERVICE AGENTS: NSW ALL GENERAL WHITEGOODS 4/11 HALLSTROM PLACE WETHERILL PARK 2164 NSW PH:02 97561511 FAX:02 97561091 VIC MASTER TECH SERVICES 9 KIRKHAM ROAD DANDENONG VIC 3175 PH: 1300 131118 FAX: 1300366705 TAS FARR ELECTRICAL CONTRATOR 286 MACQUAIRE STREET SOUTH HOBART TAS 7004 PH: 03 6223 1010 FAX 03 62237039 QUEENSLAND ENDEAVOUR REFRIGERATION 167 ROBERTSON STREET FORTITUDE VALLEY QLD 4006 PH:073 8727444 FAX:073 8522465 WA DACAPS APPLIANCE PARTS AND SERVICE 357 SEVENOAKS STREET CANNINGTON WA 6107 PH: 1800 322 277 FAX: 1800 354310 GOLD COAST ROSHAD APPLIANCE SERVICE 1/13 LEDA DRIVE BURLEIGH QLD 4220 PH:0755357044 FAX:0755357407 FOR OUTSIDE SERVICE AREAS PLEASE CONTACT OUR SERVICE & CARE CENTRE AT NEWCASTLE 02 49 209114