EdgeStar DWP60ES Owner`s manual

Dishwasher
DWP60ES
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
IMPORTANT SAFETY INFORMATION
Read all instructions carefully prior to use. For your safety, the information
detailed in this manual should be followed. Improper use and/or handling
can cause serious damage to the appliance and/or to the user including
but not limited to fire, explosion, and/or electric shock, resulting in
personal injury, or death.
Use this appliance only for its intended purpose as described in this
Ownerƍs Manual.
WATER HEATER SAFETY PRECAUTION
Hydrogen gas is flammable!
Under certain conditions, hydrogen gas may be produced in a water
heater that has not been used for more than two weeks. To prevent the
possibility of damage and/or injury, turn on all hot water faucets and allow
them to run for several minutes. Do this before using any electrical
appliance connected to the hot water system. This simple procedure will
release any built-up hydrogen gas. Since hydrogen gas is flammable, do
not smoke, use an open flame or use any appliance during this process.
PROPER INSTALLATION AND MAINTENANCE
When installing and servicing your dishwasher, refer to the following:
x This dishwasher should be properly installed and placed in a location in
accordance with the Installation Instructions prior to operation.
x Connect the dishwasher to a grounded permanent electrical system.
x Check with a qualified electrician or service representative if you are in
doubt whether the appliance is properly grounded.
Improper electrical connection poses a risk of electric shock.
x Do not attempt to repair or replace any part of your dishwasher unless it
is specifically recommended in this manual.
x All other service maintenance should be completed by a qualified
technician.
x To minimize the possibility of electric shock, disconnect this appliance
from the power supply before attempting any maintenance.
Turning the dishwasher OFF does not disconnect the
appliance from the power supply.
x Dispose of discarded appliances, including any shipping and packaging
materials, properly.
PRECAUTIONS FOR OPERATION
When using your dishwasher, follow basic precaution, including the
following:
x Use this appliance only for its intended purpose as described in this
Owner’s Manual.
x This appliance is not intended for use by children.
x Do not allow children to play with, on, or inside this or any appliance.
x Close supervision is necessary if this appliance is used near children.
x Use caution when opening or closing the door to avoid injury.
x Use only powder, tabs, liquid detergents, or rinse agents recommended
for use in a dishwasher and keep them out of the reach of children.
x Using a detergent that is not specifically designed for dishwashers may
have an undesired result such as excessive suds.
x To avoid damage to the door seal, place sharp items strategically.
x Load sharp knives handle-side up to reduce the risk of injury.
x Do not wash plastic unless it is marked as dishwasher safe. For plastic
items not marked as dishwasher safe, refer to the manufacturer’s
recommendations.
x Do not operate your dishwasher unless everything enclosed is securely
in place.
x Do not tamper with controls.
x Do not rough-handle, sit, or stand on the door or dish rack of the
dishwasher.
x Do not discard the dishwasher without removing the door.
x Do not store or use combustible materials such as gasoline or other
flammable vapors and liquids in the vicinity of this or any other
appliance.
x Contents washed in anti-bacterial mode (if available) may be hot to the
touch. Use care before handling.
x If your dishwasher is connected to a wall switch, ensure the switch is
ON prior to use.
x Do not wash non-dishware items such as furnace filters, paint brushes,
etc. in your dishwasher. Discoloration, staining, and/or other damage to
dishwasher may result.
x If you choose to turn the switch OFF between wash cycles on
dishwashers with electronic controls, allow 5 - 10 seconds after turning
the switch ON before touching the START/RESET button. This allows
the control system to reboot.
SAVE THESE INSTRUCTIONS
EdgeStar Dishwasher
ii
Table of Contents
IMPORTANT SAFETY INFORMATION............................................................... III
OPERATING PRECAUTIONS ............................................................................. III
TABLE OF CONTENTS ....................................................................................... III
INTRODUCTION ................................................................................................... 1
FEATURE IDENTIFICATION ................................................................................ 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ........................................................................................................ 2
INSTALLATION INSTRUCTIONS ........................................................................ 3
CONNECTING THE DISHWASHER ............................................................................ 3
FOR BEST RESULTS ............................................................................................. 4
DISCONNECTING THE DISHWASHER ....................................................................... 5
OPERATING INSTRUCTIONS.............................................................................. 6
WASH CYCLES..................................................................................................... 6
LOADING THE DISHWASHER .................................................................................. 7
CUTLERY BASKET ................................................................................................ 8
DETERGENT......................................................................................................... 9
RINSE AID ......................................................................................................... 11
STARTING THE WASH CYCLE ............................................................................... 12
CHANGING THE CYCLE ........................................................................................ 12
ADDING DISHES.................................................................................................. 13
END OF WASH .................................................................................................... 13
MAINTENANCE .................................................................................................. 14
TROUBLESHOOTING ........................................................................................ 16
TROUBLESHOOTING CONTINUED ......................................................................... 17
SPECIFICATIONS............................................................................................... 18
EDGESTAR LIMITED WARRANTY ................................................................... 19
iii
Introduction
Thank you for purchasing this EdgeStar dishwasher. We are glad you chose us.
We believe that your purchase of this product opens a relationship between you
and EdgeStar. We will provide the customer support needed to nurture that
relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your dishwasher. Following this manual will ensure that your
product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your dishwasher.
For Your Records:
Please write down the model number and serial number
below for future reference. You can locate your model
number on the tub wall just inside the door. Both numbers are
needed to obtain warranty service. You may also want to
staple your receipt to this manual as it is the proof of your
purchase, and is also needed for service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1
x
If you received a damaged product, immediately contact the dealer that
sold you the product.
x
Read and follow this instruction manual carefully to help you install, use
and maintain your portable air conditioner.
x
Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.
x
Visit us on the web at http://www.edgestar.com for product guides,
additional troubleshooting resources and up-to-date information. If you
need service, our friendly customer service representatives are available
via email at service@edgestar.com or by telephone at 1 (866) 3195473.
Feature Identification
Front View
Cup Shelf
Cutlery Basket
Filter System
Spray Arm
Detergent Dispenser
Rinse Aid Dispenser
Back View
Drain Pipe Connector
EdgeStar Dishwasher
Inlet Pipe Connector
2
Installation Instructions
x Remove all packaging materials carefully.
x The dishwasher must be installed on a solid, level surface.
x If your sink has a spray wand, it is recommended that the hose be
disconnected and the hole plugged.
A hose that attaches to a spray wand can burst if it is
installed on the same water line as the dishwasher.
• The minimum height clearance required to install your dishwasher on a
counter top surface with overhead cupboards is 45cm (17.7”).
• Make sure there is an electrical supply (outlet) within reach of the
electrical power supply cord (195 cm / 6.3 ft).
• Make sure the water supply/faucet connection is within reach of the inlet
and drain hose assembly (i.e., 58 cm / 22.8”).
Connecting the Dishwasher
Your dishwasher comes equipped with a ‘quick-connect’ assembly
(includes inlet and drain hose). The faucet adapter must be installed on
the faucet before you can connect the dishwasher. This adapter is
included inside your dishwasher.
The faucet adapter is compatible with faucets inclusive of either male
(outside) or female (inside) threaded faucet connections.
• Screw the faucet adapter onto (or into) the faucet tap. Check for leaks
(use Teflon or plumbers tape to eliminate any leaks if necessary).
• Connect the six-sided connection of the drain hose to the drain port
connection on the back of the dishwasher cabinet. To avoid damage to
threads, do not over-tighten.
• Connect the star-shaped connection of the inlet hose to the inlet port on
the back of the dishwasher cabinet. Do not over-tighten.
• Connect the circular connection of the drain hose onto the longer
(bottom) male connection on the quick connect.
• Connect the circular connection of the inlet hose onto the shorter (top)
male connection on the quick connect.
• Attach the quick-connect assembly onto the faucet adapter, by pulling
down the outer locking collar on the quick connect, while pushing the
quick-connect assembly upward onto the faucet adapter.
• Release the locking collar when the quick-connect assembly snaps onto
the faucet adapter. Verify the connection is secure.
3
• Slowly open the hot water line and check for any sign of water leakage
at all hose connections. If leaks are located, immediately close the
water supply and repair the hose connections.
If your existing faucet adapter is not compatible with the “quick connect”
hose assembly supplied, then the following procedures should be
followed:
• Connect the faucet adapter (included with dishwasher) to your faucet.
• If your faucet is inclusive of a ‘female’ type (threaded) connection, both
rubber washers must be installed inside the faucet adapter.
• If your faucet is inclusive of a ‘male’ type (threaded) connection, use
only the standard rubber washer (0.2”/5mm thick) supplied within the
adapter. Remove the second rubber washer.
For Best Results:
Your dishwasher cleans by spraying a mixture of clean hot water and
detergent (under pressure) against the soiled surfaces of dishes. The
water is pumped through a rotating spray arm, drained through a filter
(removing food and soiled particles) and pumped back through the spray
arm. Soiled water is pumped out and replaced with clean water at the end
of each cycle (the number of times this is repeated depends on the wash
cycle chosen).
Water Pressure
For best results, incoming water pressure should be between 15 and 20
pounds per square inch (psi).
Water Temperature
For best results, the water temperature must be at least 55ºC (130ºF). To
prevent damage to the dishwasher, the temperature of the incoming
water supply should not exceed 65ºC (149ºF).
NOTE:
Hard water conditions will adversely affect the washing performance of
your dishwasher. Hard water conditions will also contribute to ‘lime’ (white
film substance) deposits and/or ‘scaling’ on the stainless steel surface of
the dishwasher tub and heater element, located in the sump underneath
the removable filter screen. To assist in minimizing these conditions, it is
recommended to periodically operate/rinse the inside of the dishwasher
(empty) using 1 cup of white vinegar at least once a week.
EdgeStar Dishwasher
4
Disconnecting your Dishwasher
• Close the hot water supply at the faucet.
• Disconnect the power supply cord.
• Remember to release the water pressure inside the inlet hose.
x The inlet hose is pressured when the water supply line is opened, even
if closed immediately.
x To release pressure: press and hold the red pressure relief button on
the quick-connect assembly until the flow of water stops.
• Disconnect the quick-connect hose assembly by pulling down on the
outer locking collar, thus releasing it from the faucet adapter.
FAILURE TO RELIEVE WATER PRESSURE, BEFORE
DISCONNECTING THE QUICK-CONNECT ASSEMBLY FROM THE
FAUCET MAY RESULT IN BACK-PRESSURE OVER-SPRAY.
THE TEMPERATURE OF INCOMING WATER CAN BE VERY HOT.
BACK-PRESSURE OVER-SPRAY COULD CAUSE SEVERE BURNS
AND/OR SCALDING.
DO NOT LET CHILDREN DISCONNECT THE DISHWASHER. CLOSE
SUPERVISION OF CHILDREN IS ALWAYS IMPORTANT AROUND
APPLIANCES.
5
Operating Instructions
To get the best performance from your dishwasher, read all operating
instructions prior using it for the first time.
Throughout this manual, features and graphic depictions may vary from your
.
model.
5
4
3
2
1
6
7
8
1. Power Button: Press to turn the unit ON/OFF.
2. Power Light: Indicates when the ON/OFF Button has been pressed.
3. Washing Program Selector: Rotate the knob to select the desired wash cycle.
4. Start/Pause Button: Press to START, PAUSE, and RESTART the dishwasher.
5. Delay button: Press this button to DELAY start of wash cycle. Start time can be delayed in
2,4,6 or 8 hour increments.
6. Delay indicator Light: Indicates when the DELAY button has been pressed.
7. Rinse-Aid Warning light: Indicates when the rinse-aid dispenser is low.
8. Delay Time/Washing Phase indicator: This light will indicate which increment the START
time is delayed. Furthermore, when the dishwasher is operating this will indicate the phase of
, Wash
, Rinse
and Dry
the wash cycle. The phases are: Pre-wash
Program
Selector
Wash
Cycle
When Cycle Should Used
Estimated Estimated
Time
Water
Usage
Heavy
For heavily soiled dishes or cookware with driedon or baked-on soils. Everyday dishes may be
included in this cycle. However, this cycle may not
remove burnt-on foods.
For loads of everyday dishes, glasses, and
cookware with medium soils.
112 min.
4.7 gal
85 min.
3.8 gal
Eco
For lightly soiled plates, glasses, bowls and pans.
77 min.
3.4 gal
Glass
For lightly soiled glasses, crystal and fine china.
71 min.
2.9 gal
Speed
This is a shorter cycle for lightly soiled loads that
do not need drying.
45 min.
3.3 gal
Soak
For rinsing partial loads that will be washed later.
10 min.
0.7 gal
Normal
NOTE: Many dishes may have lighter soil than what the NORMAL cycle is
optimized for. Choosing a cycle other than NORMAL can save energy and water.
EdgeStar Dishwasher
6
Properly Loading the Dishwasher
A properly loaded dishwasher is key for optimal performance. Overfilling
the dishwasher can reduce the dishwasher’s efficiency. Furthermore
improper placement of items can hinder the performance of the unit.
This unit is optimized for holding 6 place settings including:
x 6 cups
x 6 bowls
x 6 large plates
x 6 small plates
x 6 dessert plates
x 2 serving dishes
x 6 sets of cutlery
Position the dishes and cookware so they are secure during the wash
cycle. Dishes and cutlery that shift in the wash cycle may hinder the spray
arms from proper motion, resulting in an undesired result. Be sure to
secure dishes and utensils so items cannot be moved by sprayed water.
6-Glasses
placed below
6-cup shelf
Cutlery basket
7
Serving
Bowl/Plate
6-Bowls
6 Small and 6
Dessert Plates
6 Large Plates and
Serving Bowl/Plate
Cutlery Basket
Silverware should be placed in the cutlery basket with handles directed
toward the bottom. If the rack has side baskets, spoons should be loaded
individually into the appropriate slots. Knives and other sharp utensils
should be placed in the basket with handles up. Longer utensils should be
placed in the horizontal position on the cup shelf instead of in the basket.
Review the diagram below for proper utensil placement:
For personal safety and a highest quality wash, securely place all
silverware in the basket:
x Be sure the similar pieces of silverware do not nest together.
x Place most silverware with handles-down.
x Place knives and other potentially dangerous utensils handles-up.
EdgeStar Dishwasher
8
Only Use Proper Detergent
Use only detergent specifically made for use in dishwashers. Keep your
detergent fresh and dry. Do not put powder detergent into the dispenser
until you are ready to wash dishes.
The amount of detergent to use depends on whether your water is hard or
soft. With hard water, you need extra detergent to alleviate the deposits
that are left by the excessive minerals. Less detergent is needed for soft
water.
To identify whether your water is hard or soft, contact your water
department. A water softener is recommended for water that contains
twelve or more grains. Without it, lime can build up in the water valve,
which could stick while open and cause flooding. Too much detergent
with soft water can cause a permanent cloudiness of glassware, called
etching.
For heavily soiled loads, use the HEAVY WASH Cycle, fill one or both of
the interior cups, depending on the hardness of your water, and also fill
the open cup on the dispenser lid.
Use the information in the table below as a guideline to determine the
amount of automatic dishwasher detergent to place in the dispenser:
Number of Grains
Less than 4
4 to 8
8 to 12
Greater than 12
Detergent Cups to Fill
15 cup
25 cup
15 and 25 cups
15, 25 cups and the open cup
To open the wash cover:
Press the button and the cover will flip back revealing the detergent
dispensing cups. See below:
9
NOTE: DO NOT USE HAND DISH DETERGENT
Using a detergent that is not specifically designed for dishwashers will
cause the dishwasher to fill with suds. During operation, these suds will
spill out of the dishwasher vents.
Since so many detergent containers look similar, store the dishwasher
detergent in a separate space from all other cleaners. Show anyone who
may use the dishwasher where the correct detergent is stored.
While there may be no lasting damage to the dishwasher by using
dishwashing detergent that is not formulated to work with dishwashers,
your dishes may not get fully clean.
EdgeStar Dishwasher
10
Use Jet-Dry Rinse Agent
Jet-Dry rinse agent removes spots and prevents new film build-up on
your dishes, glasses, flatware, cookware and plastic.
Filling the Dispenser
The rinse agent dispenser holds 3.5 oz. of rinse agent. Under normal
conditions, this will last approximately one month. Try to keep it full, but
do not overfill.
1.Make sure the dishwasher door is fully open.
2.Turn the dispenser knob to the left and lift it out.
3.Add rinse agent until the indicator window looks full.
4.Clean up any spilled rinse agent with a damp cloth.
5.Replace the dispenser knob.
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted.
The factory setting is at the midpoint. If there are rings of calcium
(hard water) spots on dishes, try a higher setting.
To adjust the setting
Remove the dispenser knob; then turn the adjuster counterclockwise
to increase the amount of rinse agent.
11
Starting the Wash Cycle
Once the dishwasher is fully loaded follow these procedures to start the
wash cycle:
x Ensure that the unit is connected to the power supply.
x Ensure that the water supply is turned on to full pressure .
x Pour in the detergent
x Press the ON/OFF switch to power the dishwasher on.
x Rotate the knob to the desired cycle. The wash cycle will be
changed as following direction:
Heavy -> Normal -> Light -> Glass -> Speed -> Soak
x Press the START/PAUSE button, the dishwasher begins to start.
NOTE:
When the START/PAUSE button is pressed during a wash cycle the cycle
is suspended and the program light will stop blinking. Unless the
START/PAUSE button is pressed to continue the cycle, an indicator beep
will be heard every minute.
Changing the Cycle
You can modify the washing cycle, but only when the dishwasher has
been running for a short time. Otherwise, detergent may have been
release, and the appliance may have already drained water. If this is the
case, the detergent dispenser must be refilled.
Opening the door during the wash cycle may result in injury
from scalding hot water.
Pressing the START/PAUSE button for three seconds or more will put the
machine in a stand-by state. At this point the cycle setting can be
changed.
The START/PAUSE light shows the state of the dishwasher:
a) All phase lights off------------------------------------------On Stand-by
b) One of the phase lights on--------------------------------------Paused
c) One of the phase light blinking--------------------------------Running
NOTE:
If the door is opened during the wash cycle, the machine will be paused.
When the door is closed, the machine will restart in 10 seconds.
EdgeStar Dishwasher
12
Forget to Add a Dish?
A dish can be added any time before the detergent cup opens.
1. Press the START/PAUSE button.
2. Open the door slightly to stop the washing.
3. You can open the door after the spray arms stop spinning.
4. Add remaining dishes.
5. Close the door.
6. Press the START/PAUSE button.
The dishwasher will restart after 10 seconds.
At the End of the Wash Cycle
When the selected wash cycle has finished, the buzzer of the dishwasher
will sound for 8 seconds. The wash cycle is completed when all phase
indicating lights are off.
Removing the Dishes
1. Switch off the dishwasher by pressing the ON/OFF button.
2. Turn off the water tap!
3. Open the door carefully. Leave the door ajar and wait a few
minutes before removing the dishes. This will allow the dishes
to cool and assist in the drying process.
4. Unload the dishwasher. It is normal for the dishwasher to be
wet inside.
13
Maintenance
Filter System
The filter system consists of a coarse filter, a flat (Main filter) And a micro
filter (Fine filter).
Main Filter
Fine Filter
Coarse Filter
1. Main filter:
Food and soil particles trapped by this filter are pulverized by a special jet
on the spray arm and washed down to drain.
2. Fine filter:
This filter holds soil and food residue in the cylindrical base and prevents
the soil from being redeposited on the dishes during wash cycle.
3. Coarse filter
Larger items, such as pieces of bone or glass, that could block the drain
are trapped in the coarse filter. To remove the items caught by the filter,
gently squeeze the tap on the top of this filter and lift out.
The filter efficiently removes food particles from the wash water, allowing
it to be re-cycled during the cycle.
For best performance and results, the filter assembly must be cleaned
regularly. For this reason, it is a good idea to remove the larger food
particles trapped in the filter after each wash cycle by rinsing the filter
assembly under running water. Use a soft cleaning brush to clean the
coarse filter and the fine filter. Reassemble the filter parts as shown in the
following diagram and reinsert the entire assembly in the dishwasher,
positioning it in its seat and pressing downward.
To remove the filter assembly, grab the handle of the fine filter, rotate it
counter-clockwise, then pull upward.
EdgeStar Dishwasher
14
Step1: Rotate the fine filter counter-clockwise;
Step2: lift it up;
Step3: lift the Main filter up
NOTE:
Reverse the steps above to install the filter system.
Important
Never run the dishwasher without the filters in place.
Improper replacement of the filter or damaged filters may
reduce the performance level of the dishwasher and/or
damage dishes and utensils.
Clean the entire filter system regularly
15
Troubleshooting
Follow the troubleshooting guide below to resolve common issues.
Issue
Dishwasher does not
start
Possible Cause
Fuse is blown or
circuit breaker is
tripped
Power Supply is
not turned on
Dishwasher door is
not properly closed
Water not pumped
from dishwater
Kink in drain hose
Filter clogged
Kitchen sink
clogged
Suds in tub
Improper detergent
Spilled rinse-aid
Stained tub interior
White film on
dishwasher interior
surface
Rust stains appear on
cutlery
EdgeStar Dishwasher
Detergent used
contained colorant
Hard water
minerals
Items are not noncorrosive.
Solution
Replace fuse or reset
circuit breaker. Remove
any other appliances
sharing the same circuit
with the dishwasher.
Ensure the dishwasher is
turned on and the door is
closed securely.
Make sure the power cord
is properly plugged into
the wall socket.
Close dishwasher,
ensuring that the door
latches.
Check drain hose
Check coarse filter
Ensure kitchen sink is
draining well. If sink is not
draining refer to a
plumber.
Use only the specified
detergent. If improper
detergent was used, open
the dishwasher allowing
suds to evaporate. Add 1
gal. of cold water to the
tub. Close and latch the
door. Start the “SOAK”
wash cycle to drain the
water. Repeat if
necessary
Always clean up rinse-aid
spills immediately.
Do not use detergents
with colorants.
While wearing rubber
gloves, use a damp
sponge to clean the
interior with dishwasher
detergent. Never use any
other cleaner to clean
dishwasher.
Do not place nondishwasher safe items in
dishwasher.
16
Troubleshooting continued
Issue
Possible Cause
Solution
Knocking noise inside
of dishwasher
The spray arm is
knocking against
an item in the dish
rack.
Rattling noise inside of
dishwasher
Item is not securely
placed in dishrack.
Knocking noise in
water pipes
Pipe cross-section
may problems.
Dishes are not cleaned
Dishes were not
loaded properly.
The wash cycle
was not powerful
enough.
Not enough
detergent was
dispensed.
Items are blocking
the path of the
spray arms.
The filter
combination in the
base of the
dishwasher is not
clean or is installed
incorrectly.
Combination of too
much detergent
with soft water.
The filter may be
dusty or blocked
Pause the wash cycle and
rearrange the items which
are obstructing the
movement of the spray
arm.
Pause the wash cycle and
secure the items in the
dish rack.
Contact a plumber. This is
not related to the
dishwasher.
See notes in loading the
dishwasher (pg. 7).
Select a more intensive
wash cycle (see pg. 6).
Cloudiness on
glassware
Black or gray marks on
dishes
Detergent left in
dispenser cup
The dishes are not dry
17
Use more or change
brand of detergent.
Rearrange the items so
the spray arms can fully
rotate (pg. 7)
Clean and/or install the
filter combination correctly
(pg. 14).
Use less detergent and/or
select the shortest wash
cycle to clean glassware.
Clean the filter and
replace it if needed
(pg.14).
Utensils may have
Use a mild abrasive
rubbed against
cleaner to eliminate
dishes
marks. Load carefully.
Dishes are blocking Re-load dishwasher
detergent cups
according to instructions.
Improper Loading
Re-load dishwasher
according to instructions.
Not enough rinseRefill and/or increase the
aid
amount of rinse-aid.
Dishes are
Do not remove dishes
removed too soon
from dishwasher
immediately.
Wrong cycle
Short cycles have lower
selected
cleaning performance.
Choose a more intensive
cycle (pg. 6).
Cutlery has a lowDishwasher is not suitable
quality coating
for low-quality coating.
Specifications
EdgeStar Dishwasher
Description of product
Dishwasher (Portable/Countertop)
Models
DWP60ES, DWP60EB, DWP60EW
Number of Place Settings
Maximum Diameter of Place
Settings
Number of Wash Cycles
Max Water Temperature
Water Consumption
(Normal Wash)
Drain Pump
6
10.5"
Interior
Voltage/Frequency
Current
Stainless Steel
120V/60Hz
5.72A
Dimensions
HxWxD
17.2” x 21.7” x 19.7”
Weight
50 lbs
6
149°F
3.8 Gallons
Yes
18
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions
set forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at
an authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts,
or exchange the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will
carry the remaining warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be
responsible for labor charges incurred. All defective products and parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may request a defective part be returned in exchange for the replacement
part. All replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by
EdgeStar under warranty service become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during
operation of the product under normal service, maintenance, and usage conditions. This warranty applies to the
purchase and use of this product in residential settings within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
x
Labor charges for installation, setup or training to use the product.
x
Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
x
Cosmetic damage such as scratches and dents.
x
Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
x
Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
x
Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses
contrary to instructions provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper installation,
unauthorized service, maintenance negligence, unauthorized installation or modification, or commercial use.
x
Labor charges incurred 91 days or more after the date of original purchase.
x
The use of EdgeStar products in commercial settings.
x
Optional accessories, attachments, and appearance items.
x
Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar.
x
Products lost in shipment, or theft.
x
Products sold AS IS or from an unauthorized reseller.
x
Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and
warranty service at 1-866-319-5473. Please have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the
product must be returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping
related costs to and from the repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling
or improper packaging. Do not return a defective product to the place of purchase. Products received without a return
authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER
THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS,
OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE.
19
EdgeStar Products
Box 81336
Austin, TX 78708-1336
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: service@edgestar.com
Register your product, download owner’s manuals, access additional
troubleshooting resources, and obtain more information on other great
EdgeStar products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2009 Living Direct, Inc.