HDCVI Series DVR User’s Manual
Version 1.0.0
Welcome
Thank you for purchasing your HDCVI DVR from eLine Technology!
This user’s manual is designed to be a reference tool for the installation and
operation of your system.
Here you can find information about the HDCVI DVR features and functions,
as well as a detailed menu tree.
Before installation and operation please read the following safeguards and
warnings carefully!
‐ 1 ‐ Important Safeguards and Warnings
1.Electrical safety
All installation and operation should conform to your local electrical safety
codes. The DVR must be grounded to reduce the risk of electric shock. We
assume no liability or responsibility for fire or electrical shock caused by
improper handling or installation.
2.Equipment Security
Heavy stress, violent vibration or water splash are not allowed during
transportation, storage and installation.
3.Installation
Keep upwards. Handle with care.
Do not apply power to the DVR before completing installation.
Do not place objects on the DVR.
4.Qualified engineers needed
All the examination and repair work should be done by qualified service
engineers.
We are not liable for any problems caused by unauthorized modifications or
attempted repair.
5.Environment
The DVR should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances, etc.
The HDCVI DVR shall be transported, storaged and used at room
tempreature.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components
that are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury! When
replaceing the battery, please make sure you are using the same model!
Contact your local retailer.
‐ 2 ‐ MENU
1. Features and Specifications ...................................................................... ‐ 4 ‐
2. Overview and Controls ............................................................................... ‐ 5 ‐
3. Boot up and Shutdown ............................................................................... ‐ 9 ‐
4. WEB Operation .......................................................................................... ‐ 71 ‐
5. Professional Surveillance System ........................................................ ‐ 126 ‐
6. FAQ ........................................................................................................... ‐ 126 ‐
Appendix A HDD Capacity Calculation ............................................. ‐ 132 ‐ Appendix B Compatible Backup Device List .................................... ‐ 133 ‐ Appendix C Compatible CD/DVD Device List ................................... ‐ 139 ‐ Appendix D Compatible Displayer List ............................................. ‐ 139 ‐ Appendix E Compatible Switcher List ............................................... ‐ 140 ‐ Appendix F Compatible Wireless Mouse List .................................. ‐ 141 ‐ Appendix G Specifications .................................................................. ‐ 141 ‐ Appendix H Toxic or Hazardous Materials or Elements ................. ‐ 145 ‐ ‐ 3 ‐ 1. Features and Specifications
1.1 Overview
This HDCVI DVR is a Professional grade digital monitoring product designed
for the security field. It adopts an embedded Linux OS to maintain reliable
operation. It is easy to use and can realize surveillance function after some
simple setups. It has various functions such as record, playback, mutimonitoring and can guarantee audio video synchronization. The HDCVI DVR
has advanced technology and strong network data transmission functions.
The HDCVI DVR adopts embedded design to achieve high security and
reliability. It can work in the local end, and simultaneously, when connected to
the professional surveillance software (PSS), can realize strong network and
remote monitor functions. It can realize HD monitoring without changing the
current cable layout.
The HDCVI DVR can be widely used in various areas such as banking,
telecommunication, electric power, interrogation, transportation, intelligent
resident zone, factory, warehouse, resources, and water conservancy.
1.2 Features
Real-time monitoring
It has analog output port, VGA port and HDMI port. You can use monitor or
displayer to realize surveillance function.
System supports VGA/HDMI output at the same time.
Storage function
Special data format to guarantee data security and can avoid vicious data
modification.
Compression format
Support multiple-channel audio and video. An independent hardware decodes
the audio and video signal from each channel to maintain video and audio
synchronization.
Backup function
Support backup operation via USB port (such as flash disk, portable HDD,
burner).Client-end user can download the file to local HDD to backup via
network.
Record playback function
Support each channel real-time record independently, and at the same time it
can support search, forward play, network monitor, record search, download
and etc.
Support various playback modes: slow play, fast play, backward play and
‐ 4 ‐ frame by frame play.
Support time title overlay so that you can view event accurate occurred time
Support specified zone enlargement.
Network operation
Support network remote real-time monitor, remote record search and remote
PTZ control.
Alarm activation function
Several relay alarm outputs to realize alarm activation and on-site light control.
The alarm input port and output has the protection circuit to guarantee device
safety.
Communication port
RS485 port can realize alarm input and PTZ control.
RS232 port can connect to keyboard to realize central control, and can also
connect to PC COM to upgrade system and realize maintenance, and matrix
control. Standard Ethernet port can realize network access function.
PTZ control
Support PTZ decoder via RS485.
Support various decode protocols to allow the PTZ to control the speed dome.
Intelligent operation
Mouse operation function
In the menu, support copy and paste setup function
UPnP
It is to establish the mapping relationship between the LAN and the WAN via
the UPnP protocol.
Slight function differences may be found due to different series.
2. Overview and Controls
2.1 HDD Installation
This HDCVI DVR has only one SATA HDD. Please use HDD of 7200rpm
or higher. You can refer to the User’s Manual for recommended HDD
brand. Please follow the instructions below to install hard disk.
‐ 5 ‐ 1. Loosen the screws of the
upper cover and side panel.
2. Fix four screws in the HDD
3. Place the HDD in
accordance with the four holes
in the bottom.
4. Turn the device upside
down and then turn the
screws in firmly.
5.Fix the HDD firmly.
6. Connect the HDD cable and
power cable.
7. Put the cover in accordance
with the clip and then place the
upper cover back.
8. Secure the screws in the
rear panel and the side panel.
Note:
You can connect the HDD data cable and the power cable first and then
fix the HDD in the device.
Please pay attention to the front cover. It adopts the vertical sliding design.
‐ 6 ‐ You need to push the clip first
and then put down.
2.2 Rear Panel
4CH and 8CH CVI DVR
Here we take the 4-channel series product rear panel as an example
The 8-channel series rear panel is shown as below
Please refer to the following sheet for detailed information.
SN
1
4
7
10
Name
Video input
Video VGA output
Network port
NC
SN
2
5
8
11
Name
Audio output
HDMI port
RS-485 input port
GND port
SN
3
6
9
NAME
Audio input
USB port
Power socket
2.3 Connection Sample
2.3.1 4CH/8CH CVI DVR
Please note the following contents are based on our 1U 720P series product.
For detailed operation instruction of other series products, please refer to the
‐ 7 ‐ User’s Manual included in the resources CD.
The following figure is based on the 4-channel series product.
2.4 Connecting Audio Input & Output, Bidirectional
Audio
2.4.1 Audio Input
These HDCVI DVRs audio input port adopt BNC port. Due to high impedance
of audio input, please use active sound pick -up. Audio transmission is similar
to video transmission. Try to avoid interference, dry joint, loose contact. And it
shall be away from high tension current.
2.4.2 Audio Output
The audio output signal parameter is usually over 200mv 1KΩ (BNC or RCA). It
can directly connect to low impedance earphone, active sound box or
amplifier-drive audio output device. If the sound box and the pick-up cannot be
separated spatially, it is easy to arouse squeaking. In this case you can adopt
the following measures:
Use better sound pick-up with better directing property
Reduce the volume of the sound box.
Using more sound-absorbing materials in decoration can reduce voice
echo and improve acoustics Environment.
Adjust the layout to reduce happening of the squeaking.
‐ 8 ‐ 2.5 RS485
When the DVR receives a camera control command, it transmits that
command up the coaxial cable to the PTZ device. RS485 is a single-direction
protocol; the PTZ device can’t return any data to the unit. To enable X289
H289H289H X Since RS485 is disabled by default for each camera, you must
enable the PTZ settings first. This series DVRs support multiple protocols such
as Pelco-D, Pelco-P. To connect PTZ devices to the DVR:
1. Connect RS485 A,B on the DVR rear panel.
2. Connect the other end of the cable to the proper pins in the connector on the
camera.
3. Please follow the instructions to configure a camera to enable each PTZ
device on the DVR.
3. Boot up and Shutdown
3.1.1 Boot up and Shutdown
Boot up
Before the boot up, please make sure:
The rated input voltage matches the device power on-off button. Please
make sure the power Wire connection is OK. Then click the power on-off
button.
Always use the stable current, if necessary UPS is a best alternative
measure. Please follow the steps listed below to boot up the device
Connect the device to the monitor and then connect a mouse.
Connect power cable
Click the power button at the front or rear panel and then boot up the
device. After device booted up, the system is in multiple-channel display
mode by default.
Shutdown
Note
When you see corresponding dialogue box “System is shutting down…” Do not
click power on –off button directly.
Do not unplug the power cable or click power on-off button to shutdown
device directly when Device is running (especially when it is recording.)
There are three ways for you to log out.
a)Main menu (RECOMMENDED)
From Main Menu->Shutdown, select shutdown from dropdown list.
‐ 9 ‐ Click the OK button, the device will shut down.
b)The power (on-off) button on the front panel or remote control
Press the power (on-off) button on the DVR front panel or remote control
for more than 3 seconds to shutdown the device.
c)From the power (on-off) button on the rear panel
Replace Button Battery
Please make sure to use the same battery model if possible.
We recommend replace battery regularly (such as one-year) to
guarantee system time accuracy. Contact local retailer.
Note:
Before replacement, please save the system setup, otherwise, you may lose
the data completely!
3.1.2 Startup Wizard
After device successfully booted up, it goes to startup wizard.
Click Cancel/Next button, you can see system goes to login interface.
Tips
Check the box Startup button here, system goes to startup wizard again when
it boots up the next time. Cancel the Startup button, system goes to the login
interface directly when it boots up the next time.
Click Cancel button or Next Step button, system goes to login interface.
‐ 10 ‐ System consists of four accounts:
Username: admin. Password: admin. (administrator, local and network)
Username: 888888. Password: 888888. (administrator, local only)
Username: 666666. Password: 666666(Lower authority user who can
only monitor, playback, backup and etc.)
Username: default. Password: default (hidden user). Hidden user
“default” is for system interior use only and can not be deleted. When
there is no login user, hidden user “default” automatically login. You can
set some rights such as monitor for this user so that you can view some
channel view without login.
Note:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and five
times login failure will result in account lock!
3.2 Right-Click Menu
On the preview interface, right click mouse, you can view menu interface
Tips. After you go to the corresponding interface, right click mouse to go back
to the upper-level
‐ 11 ‐ 3.2.1 Preview
After you logged in, the system is in live viewing mode by default. You can
see system date, time and channel name. If you want to change the system
date and time, you can refer to general settings (Main
Menu->Setting->System->General). If you want to modify the channel name,
please refer to the display settings (Main Menu->Setting->Camera->CAM
Name)。
1
Recording status
3
Video loss
2
Motion detection
4
Camera lock
Ti ps
Preview drag: If you want to change position of channel 1 and channel 4
when you are previewing, you can left click mouse in the channel 1 and
then drag to channel 4, release mouse you can switch channel 1 and
channel 4 positions.
Use mouse middle button to control window split: You can use mouse
middle button to switch window split amount.
Preview Control
The preview control function has the following features.
Support preview playback. In the preview desktop, system can playback
previous 5-60 minutes record of current channel.
Please go to the Main Menu->Setting->->System->General to set
real-time playback time.
Support drag and play function. You can use your mouse to select any
playback start time.
Support playback, pause and exit function. Right now, system does not
support slow playback and backward playback function.
Support digital zoom function.
Support real-time backup function.
You can follow the contents listed below for the operation instruction.
Preview control interface
Move your mouse to the top centre of the video of current channel, you can see
system pops up the preview control interface. If your mouse stays in this area
for more than 6 seconds and has no operation, the control bar automatically
hides.
‐ 12 ‐ You can refer to the following sheet for detailed information.
SN Name
Function
Real time
It is to playback the previous 5-60 minutes record
1
playback
of current channel. Please go to the Main
Menu->Setting->->System- >General to set
real-time playback time. System may pop up a
dialogue box if there is no such record in current
channel.
2
Digital zoom
It is to zoom in specified zone of current channel. It
supports zoom in function of multiple-channel.
, the button is shown as Drag the
Click button
mouse or use the middle button to select a zone,
you can view. Right click mouse to cancel zoom
and go back to the original interface.
3
Real-time
backup
function
It is to backup the video of current channel to the
USB device. System can not backup the video of
multiple-channel at the same time. Click button
,system begins recording. Click it again,
system stops recording. You can find the record
file on the flash disk.
playback control
The playback control has the following features.
Support play, pause, and exit and drag function.
During the preview playback process, you can not see the channel title
and record status of current channel. It will display the channel title and
the record status once you exit the preview playback.
During the preview playback, you can not switch the displayed channel or
change current window-display mode.
System closes preview control interface when you are switching split
mode.
Please note the tour function has the higher priority than the preview
playback. You can not control the preview playback until the tour function
ended.
3.2.2 PTZ Control
‐ 13 ‐ Please note the commend name is grey once device does not support this
function. The PTZ operation is only valid in one-window mode.
PTZ Setup
In the main menu, from Setting->System->PTZ, you can see the following
interface. The pan/tilt/zoom setup includes the following items. Please select
channel first.
Protocol: Select corresponding PTZ protocol such as PELCOD.
Address: Input corresponding PTZ address.
Baud rate: Select baud rate.
Data bit: Select data bit. Default value is 8.
Stop bit: Select stop bit. Default value is 1.
Parity: There are three choices: none/odd/even. Default value is none.
In one window display mode, right click mouse (click “Fn” Button in the front
panel or click “Fn” key in the remote control). Click Pan/Tilt/Zoom, the interface
is shown as below. Here you can set the following items: Step: value ranges
from 1 to 8.Zoom.Focus .Iris
‐ 14 ‐ PTZ set
Here you can control PTZ direction, speed, zoom, focus, iris, preset, tour, scan,
pattern aux function, light and wiper, rotation and etc
Speed is to control PTZ movement speed. The value ranges from 1 to 8.The
speed 8 is faster than speed 1. You can use the remote control to click the
small keyboard to set. You can click
and
of the zoom, focus and iris
to zoom in/out, definition and brightness.
The PTZ rotation supports 8 directions. If you are using direction buttons on the
front panel, there are only four directions: up/down/left/right.
Here is a sheet for you reference.
Name
Function
key
function
Shortcut
key
Zoom
Near
Focus
Iris
Function
key
function
Shortcut
Key
►
Far
▶▶
Near
◀
Far
►
close
▌▌◀
Open
▶▌▌
In the middle of the eight direction arrows, there is a 3D intelligent positioning
key. .
Please make sure your protocol supports this function and you need to use
mouse to control. Click this key, system goes back to the single screen mode.
Drag the mouse in the screen to adjust section size. The dragged zone
supports 4X to 16X speeds . It can realize PTZ automatically. The smaller zone
you dragged, the higher the speed.
PTZ Function Setup
‐ 15 ‐ Click
you can go to the following interface to set p Click reset,
tour, pattern, and scan
Preset Setup
click the preset button and use eight direction arrows to adjust camera to the
proper position.
Click Set button and then input preset number.
Click Set button to save current preset.
Tour Setup
Click tour button. Input tour value and preset No. Click Add preset button to
add current preset to the tour.
Tips
Repeat the above steps to add more presets to the tour. Click Del preset button
to remove it from the tour. Please note some protocols do not support delete
preset function.
Pattern Setup
Click Pattern button and input pattern number.
Click Begin button to start direction operation. Or you can go to operate
zoom/focus/iris/direction operation. Click End button
Scan Setup
Click Scan button.
Use direction buttons to set camera left limit and then click Left button.
Use direction buttons to set camera right limit and then click Right button. Now
the scan setup process is complete.
3.2.3 Figure Color
Here you can set hue, brightness, contrast, saturation, gain, white level, color
mode and etc
‐ 16 ‐ Please refer to the following sheet for detailed information.
Item
Note
Period
There are two periods in one day. You can set different
sharpness, brightness, and contrast setup for different
periods.
Effective
Time
Contrast
Brightness
Check the box here to enable this function and then set
period time.
The value here is to adjust the edge of the video. The value
ranges from 0 to 100. The larger the value is, the clear the
edge is and vice versa. Please note there is noise if the
value here is too high. The default value is 50 and the
recommended value ranges from 40 to 60.
It is to adjust monitor window bright. The value ranges from 0
to 100. The default value is 50. The larger the number, the
bright the video is. When you input the value here, the bright
section and the dark section of the video will be adjusted
accordingly. You can use this function when the whole video
is too dark or too bright. Please note the video may become
hazy if the value is too high. The recommended value
ranges from 40 to 60.
3.2.4 Playback
‐ 17 ‐ 1
Display
2
Search type
3
Calendar
4
Channel selection
5
window
6
Clip
Playback
control
7
Smart search
8
Time bar
9
Record type
10
Time bar unit
Display window
Here is to display the searched picture or file.
Support 1/4/8-window playback.
Search type
Here you can select to search the picture or the recorded file”
Record search
You can select to play from the read-write HDD, from peripheral device or from
redundancy HDD
Important
Redundancy HDD does not support picture backup function, but it
supports picture playback function. You can select to play from
redundancy
HDD if there are pictures on the redundancy HDD.
Figure search
Before you select to play from the peripheral device, please connect the
corresponding peripheral device. You can view all record files of the root
directory of the peripheral device. Click the Browse button; you can select the
file you want
‐ 18 ‐ Calendar
The blue highlighted date means there is picture or file. Otherwise, there is no
picture or file. In any play mode, click the date you want to see, you can see the
corresponding record file trace in the time bar.
Channel selection
Playback mode:1/4/9. (It may vary due to different series.)
In 1-window playback mode: you can select 1-16 channels.
In 4-window playback mode: you can select 4 channels according to your
requirement.
In 9-window playback mode, you can switch between 1-8 and 9-16 channels.
The time bar will change once you modify the playback mode or the channel
Playback control
Smart Search
When system is playing, you can select a zone in the window to begin
smart search. Click the motion detect button to begin play.
Once the motion detect play has begun, click button again will terminate
current motion detect file play. There is no motion detect zone by default.
If you select to play other file in the file list, system switches to motion
detect play of other file.
During the motion detect play process, you can not implement operations
such as change time bar, begin backward playback or frame by frame
playback.
Smart search step
During the multiple-channel playback mode, double click one channel and then
click
,system begins smart search. System supports 396(22*18 PAL)
and 330(22*15 NTSC) zones. Please left click mouse to select smart search
zones. Click the
,you can go to the smart search playback. Click it again,
system stops smart search playback。
Important
System does not support motion detect zone setup during the full-screen
mode.
During the multiple-channel playback, system stops playback of rest
channels if you implement one-channel smart search.
‐ 19 ‐ Clip
1,Please play the file you want to edit and then click this button when you want
to edit. You can see the corresponding slide bars in the time bar of the
corresponding channel. You can adjust the slide bar or input the accurate
time to set the file end time.
2,After you set, you can click Clip button again to edit the second period. You
can see the slide bar restore its previous position.
3,Click Backup button after clip, you can save current contents in a new file.
4, You can clip for one channel or multiple-channel. The multiple-channel click
operation is similar with the one-channel operation.
Please note:
System max supports 1024 files backup at the same time.
You can not operate clip operation if there is any file has been check
ending the file
Smart search
Select records from one day, click the list, you can go to the file list interface.
You can input time at the top right corner to search records by time. input time
11:00.00 and then click Search button you can view all the record files after
11:00.00(The records includes current time.) Double click a filename to
playback
Note
After you searched files, system implement accurate playback once you click
Play for the first time. System does not support accurate playback for picture
‐ 20 ‐ System supports synchronization playback and non-synchronous playback.
The synchronization playback supports all channels and non-synchronous
playback only supports accurately
playback of current select channel.
Time bar
It is to display the record type and its period in current search criteria .In
4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
Use the mouse to click one point of the color zone in the time bar, system
begins playback. The time bar is beginning with 0 o'clock when you are
setting the configuration.
The time bar zooms in the period of the current playback time when you
are playing the file.
The green color stands for the regular record file. The red color stands for
the external alarm record file.
The yellow stands for the motion detect record file
File type
File type: R—regular record; A—external alarm record; M—Motion
detect record.
Time bar unit
The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger
the zoom rate. You can accurately set the time in the time bar to playback the
record. The time bar is beginning with 0 o'clock when you are setting the
configuration. The time bar zooms in the period of the current playback time
when you are playing the file
‐ 21 ‐ 3.3 Main Menu
3.3.1Main Menu
The main menu interface is shown as below 。
3.3.2 Record
Record
Note:
You need to have proper rights to implement the following operations. Please
make sure the HDD
shave been properly installed. After the system booted up, it is in default
24-hour regular mode. You can set record type and time on schedule interface.
‐ 22 ‐ Channel: Please select the channel number first. You can select “all” if
you want to set for the whole channels.
Record Type: Please check the box to select corresponding record type.
There are four types:
Regular/MD (motion detect)/Alarm/MD&Alarm.
Week day: There are eight options: ranges from Saturday to Sunday and
all.
Holiday: It is to set holiday setup. Please note you need to go to the
General interface (Main Menu ->System->General) to add holiday first.
Otherwise you can not see this item.
Pre-record: System can pre-record the video before the event occurs into
the file. The value ranges from 1 to 30 seconds depending on the bit
stream .
Redundancy: System supports redundancy backup function. You can
highlight Redundancy button to activate this function. Please note, before
enable this function, please set at least one HDD as redundant. (Main
menu->Setting->Storage->HDD Manager).
Please note this function is null if there is only one HDD.
Backup
DVR support CD-RW, DVD burner, USB device backup, network
download and eSATA. Here we introduce USB, eSATA backup. You can
refer to Chapter 5 Web Operation for network download backup operation.
Click backup button, you can see an interface is shown as in Figure 3-21.
Here is for you to view devices information. You can view backup device
name and its total space and free space. The device includes CD
‐ 23 ‐ -RW ,DVD burner, USB device, flash disk, eSATA backup.
Select backup device and then set channel, file start time and end time.
Click add button, system begins search. All matched files are listed below.
System automatically calculates the capacity needed and remained. System
only backup files with a √ before channel name. You can use Fn or cancel
button to delete√ after file serial number. Click Start button, system begins
copy. At the same time, the backup button becomes stop button. You can view
the remaining time and process bar at the left bottom
When the system completes backup, you can see a dialogue box prompting
successful backup file format: Click the file format; you can see there are two
options: DAV/ASF. The file name format usually is: Channel number+Record
type+Time. In the file name, the YDM format is Y+M+D+H+M+S. File extension
name is .dav.
‐ 24 ‐ Tips:
During backup process, you can click ESC to exit current interface for other
operation. The system will not terminate backup process
Note:
When you click stop button during the burning process, the stop function
becomes activated immediately. For example, if there are ten files, when you
click stop system just backup five files, system only save the previous 5 files in
the device (But you can view ten file names).
Alarm Detect
In the main menu, from Manu->Alarm->Detect, you can see motion detect
interface. There is three detection types: motion detection, video loss,
tampering
The video loss has no detection region and sensitivity setup and
tampering has no detection region setup.
You can see motion detect icon if current channel has enabled motion
detect alarm.
You can drag you mouse to set motion detect region. Please click OK
button to save current .region setup. Right click mouse to exit current
interface.
3.3.2.4.1Motion Detect
After analysis video, system can generate a video loss alarm when the
detected moving signal reached the sensitivity you set here.
Event type: From the dropdown list you can select motion detection type.
Channel: Select a channel from the dropdown list to set motion detect
function.
Enable: Check the box here to enable motion detect function.
Region: Click select button, the interface is shown as in Figure 3-25. Here
you can set motion detection zone. There are four zones for you to set.
Please select a zone first and then left drag the mouse to select a zone.
The corresponding color zone displays different detection zone. You can
click Fn button to switch between the arm mode and disarm mode. In arm
mode, you can click the direction buttons to move the green rectangle to
set the mot ion detection zone. After you completed the setup, please click
ENTER button to exit current setup. Do remember click save button to
save current setup. If you click ESC button to exit the region setup
interface system will not save your zone setup. Sensitivity: System
supports 6 levels. The sixth level has the highest sensitivity.
‐ 25 ‐ Anti-dither: Here you can set anti-dither time. The value ranges from 5 to
600s. The anti-dither time refers to the alarm signal lasts time. It can be
seem as the alarm signal activation stays such as the buzzer, tour, PTZ
activation, snapshot, channel record. The stay time her e does not include
the latch time. During the alarm process, the alarm signal can begin an
anti -dither time if system detects the local alarm again. The screen
prompt, alarm upload, email and etc will not be activated. For example, if
you set the anti-dither time as 10 second, you can see the each activation
may last 10sif the local alarm is activated. During the process, if system
detects another local alarm signal at the fifth second, the buzzer, tour,
PTZ activation, snapshot, record channel will begin another 10swhile the
screen prompt, alarm upload, email will not be activated again. After 10s,
if system detect san other alarm signal, it can generate an alarm since the
anti -dither time is out.
Period: Click set button, you can see an interface. Here you can set
motion detect period. System only enables motion detect operation in the
specified periods. It is not for video loss or the tampering. There are two
ways for you to set periods. Please note system only supports 6 periods
in one day
‐ 26 ‐ There are four record types: regular, motion detection (MD), Alarm, MD &
alarm.
Alarm output: when an alarm occurs, system enables peripheral alarm
devices.
Latch: when motion detection complete, system auto delays detecting for
a specified time. The value ranges from 1-300(Unit: second)Show
message: System can pop up a message to alarm you in the local host
screen if you enabled this function.
Alarm upload: System can upload the alarm signal to the network
(including alarm centre) if you enabled current function.
Send email: System can send out email to alert you when an alarm
occurs.
Record channel: System auto activates motion detection channel(s) to
record once an alarm occurs. Please make sure you have set MD record
in Schedule interface(Main Menu ->Setting->Schedule)and schedule
record in manual record interface(Main Menu->Advanced->Manual
Record) PTZ activation: Here you can set PTZ movement when an alarm
occurs. Such as go to preset, tour& pattern when there is an alarm. Click
“select” button, you can see an interface is shown as in
Record Delay: System can delay the record for specified time after alarm
ended. The value ranges from 10s to 300s.
Tour: Here you can enable tour function when alarm occurs. System
one-window tour.
Snapshot: You can enable this function to snapshoot image when a
‐ 27 ‐ motion detect alarm occurs. Video matrix Check the box here to enable
this function. When an alarm occurs, SPOT OUT port displays device
video output. It displays video (1-window tour) from alarm activation
channel you select at the record channel item.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when
alarm occurs.
Test: Click it to test current motion detect setup (do not need to save).
Click Select button after
Please highlight icon to select the corresponding function. After all the setups
please click save button, system goes back to the previous menu.
Note:
may not be the same, you can left click mouse and then drag it to set a region
for motion detection. Click Fn to switch between arm/withdraw motion detection.
After setting, click enter button to exit Motion detect here only has relationship
with the sensitivity and region setup. It has no relationship with other setups.
‐ 28 ‐ Video Loss
Select video loss from the type list. You can see the interface is shown This
function allows you to be informed when video loss phenomenon occurred.
You can enable alarm output channel and the n enable show message
function.
Tips:
You can enable preset/tour/pattern activation operation when video loss
occurs.
‐ 29 ‐ Please refer to chapter 4.10.3.1.1 motion detection for detailed information.
Tampering
When someone viciously masks the lens, or the output video is in one-color
due to the environments light change, the system can alert you to guarantee
video continuity. Tampering interface is shown You can enable
Sensitivity: The value ranges from 1 to 6. It mainly concerns the brightness.
The level 6 has the higher sensitivity than level 1. The default setup is 3
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
Please refer to chapter 4.10.3.1.1 motion detection for detailed information.
Note:
In Detect interface, copy/paste function is only valid for the same type, which
means you cannot copy a channel setup in video loss mode to tampering mode.
About Default function. Since detection channel and detection type may not be
the same, system can only restore default setup of current detect type. For
example, if you click Default button at the tampering interface, you can only
restore default tampering setup. It is null for other detect types. System only
enables tampering function during the period you set here. It is null for motion
detect or video loss type.
3.3.3 System
‐ 30 ‐ General
Device ID: Please input a corresponding device name here.
Device No: Here you can set device number.
Language: System supports various languages: Chinese (simplified),
Chinese (Traditional), English, Italian Japanese, French, Spanish (All
languages listed here are optional. Slight difference may be found in
various series.)
Video standard: There are two formats: NTSC and PAL.
HDD full: Here is for you to select working mode when hard disk is full.
There are two options: stop recording or rewrite. If current working HDD is
overwritten or the current HDD is full while the next HDD is no empty, then
system stops recording, If the current HDD is full and then next HDD is not
empty, then system overwrites the previous files.
Pack duration: Here is for you to specify record duration. The value ranges
from 1 to 120 minutes. Default value is 60 minutes.
Real-time playback: It is to set playback time you can view in the preview
interface. The value ranges from 5 to 60 minutes.
Auto logout: Here is for you to set auto logout interval once login user
remains inactive for a specified time. Value ranges from 0 to 60 minutes.
Navigation bar: Check the box here, system displays the navigation bar on
the interface.
‐ 31 ‐ Startup wizard: Once you check the box here, system will go to the startup
wizard directly when the system restarts the next time. Otherwise, it will go
to the login interface.
Mouse property: You can set double click speed via dragging the slide
bard. You can Click Default button to restore default setup. Date and time:
Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or
DD-MM-YYYY.
Date separator: There are three denotations to separate date: dot, beeline
and solidus.
DST: Here you can set DST time and date. Here you can set start time
and end time by setting corresponding week setup or by setting
corresponding date setup.
NTP: It is to set NTP server information
Holiday:
Holiday setup interface is shown as in Figure 4-100. Click Add new holiday
button, you can input new holiday information. See Figure 4-101. Here you can
set holiday name, repeat mode and start/end time
Note
When you enable Holiday settings and schedule setup at the same time,
holiday setting has the priority. If the selected day is a holiday, then
system records as you set in holiday setting. If it is nota holiday, system
records as you set in Schedule interface.
Please note Please note, there is no year setup on the holiday setup. For
example, if you set 30th Oct, 2012 as a holiday, then the date of 30th Oct
in each year will be set as a holiday.
‐ 32 ‐ Encode
It is to set video bit stream, picture bit stream, video overlay parameter and etc
Channel: Select the channel you want.
Type: Please select from the dropdown list. There are three options:
regular/motion detect/alarm. You can set the various encode parameters
for different record types Compression: System supports H.264 and
MJPEG.
‐ 33 ‐ Resolution: System supports various resolutions, you can select from the
dropdown list. Please Note the option may vary due to different series.
Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in
PAL mode.
Bit rate type: System supports two types: CBR and VBR. In VBR mode,
you can set video quality.
Quality: There are six levels ranging from 1 to 6. The sixth level has the
highest image quality.
Video/audio: You can enable or disable the video/audio.
Audio: Please select from the dropdown list.
3.3.3.4.1Overlay
Cover area: Here is for you to set cover area. You can drag you mouse to
set proper section size. In channel video, system max supports 4 zones in
one channel. Preview/monitor: privacy mask has two types. Preview and
Monitor. Preview means the privacy mask zone can not be viewed by user
when system is in preview status. Monitor means the privacy mask zone
can not be view by the user when system is in monitor status.
Time display: You can select system displays time or not when you
playback. Please click set button and then drag the title to the
corresponding position in the screen. Channel display: You can select
system displays channel number or not when you playback. Please
click set button and then drag the title to the corresponding position in the
screen.
Copy :After you complete the setup, you can click Copy button to copy
current setup to other channel(s) . You can see an interface is shown as in
Figure 3-43. You can see current channel number is grey.
Please check the number to select the channel or you can check the box
‐ 34 ‐ ALL.
Snapshot
Here you can set snapshot mode, picture size, quality and frequency.
Snapshot mode: There are two modes: regular and trigger. If you set
timing mode, you need to set snapshot frequency. If you set trigger
snapshot, you need to set snapshot activation
Operation. Image size: Here you can set snapshot picture size.
Image quality: Here you can set snapshot quality. The value ranges from 1
to 6.
Interval: It is for you to set timing (schedule) snapshot interval.
“Menu > Record > Record Set”,Open “Snapshot”.
Trigger Snapshot
‐ 35 ‐ Please follow the steps listed below to enable the activation snapshot function.
After you enabled this function, system can snapshot when the corresponding
alarm occurred In main menu, from Menu->Record->Record set, here you can
input snapshot mode as regular, size,
In main menu, from Menu->Alarm->Detect, please enable snapshot function
for specified channels
Image FTP
In the main menu, from Setting->Network->FTP, you can set FTP server
information. Please enable FTP function and then click save button
‐ 36 ‐ IP Version: There are two options: IPv4 and IPv6. Right now, system
supports these two IP Address format and you can access via them.
MAC address: The host in the LAN can get a unique MAC address. It is for
you to access in the LAN. It is read-only.
IP address: Here you can use up/down button or input the corresponding
number to input IP address. Then you can set the corresponding subnet
‐ 37 ‐ mask the default gateway.
Default gateway: Here you can input the default gateway. Please note
system needs to check the validity of all IPv6 addresses. The IP address
and the default gateway shall be in the same IP section. That is to say, the
specified length of the subnet prefix shall have the same string .
DHCP: It is to auto search IP. When enable DHCP function, you can not
modify IP/Subnet mask/Gateway. These values are from DHCP function.
If you have not enabled DHC P function, IP/Subnet mask/Gateway display
as zero. You need to disable DHCP function to view current IP information.
Besides, when PPPoE is operating, you can not modify IP/Subnet mask
Gateway. MTU: It is to set MTU value of the network adapter. The value
ranges from 1280 -7200. The default setup is 1500 bytes. Please note
MTU modification may result in network adapter reboot and network
becomes off. That is to say, MTU modification can affect current network
service. System may pop up dialog box for you to confirm setup when you
want to change MTU setup. Click OK button to confirm current reboot, or
you can click Cancel button to terminate current modification. Before the
modification, you can check the MTU of the gateway; the MTU of the DVR
shall be the same as or is lower than the MTU of the gateway. In this way,
you can reduce packets and enhance network transmission efficiency.
1500: Ethernet information packet max value and it is also the default
value. It is the typical setup when there is no PPPoE or VPN. It is the
default setup of some router, switch or the network adapter.
1492: Recommend value for PPPoE.
1468: Recommend value for DHCP.
Preferred DNS server: DNS server IP address.
Alternate DNS server: DNS server alternate address.
Transfer mode: Here you can select the priority between fluency/video
qualities.
LAN download: System can process the downloaded data first if you
enable this function. The
download speed is 1.5X or 2.0X of the normal speed.
LAN download: System can process the downloaded data first if you
enable this function. The download
5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back
to the previous menu.
Network service
‐ 38 ‐ IP Filter
IP filter interface is shown as in Figure 4-61. You can add IP in the following list.
The list supports max64 IP addresses. System supports valid address of IPv4
and IPv6.
Please note system needs to check the validity of all IPv6 addresses and
implement optimization.
After you enabled trusted sites function, only the IP listed below can access
current DVR. If you enable blocked sites function, the following listed IP
addresses can not access current DVR
Enable: Highlight the box here, you can check the trusted site function and
blocked sites function.
You can not see these two modes if the Enable button is grey.
Type: You can select trusted site and blacklist from the dropdown list. You
can view the IP address on the following column.
Start address/end address: Select one type from the dropdown list, you
can input IP address in the start address and end address. Now you can
click Add IP address or Add IP section to add
For the newly added IP address, it is in enable status by default.
Remove the √ before the item, and then current item is not in the list.
System max supports 64 items.
Address column supports IPv4 or IPv6 format. If it is IPv6 address,
system can optimize it. For example, system can optimize aa:0000: 00:
00aa: 00aa: 00aa: 00aa: 00aa as aa:: aa: aa: aa:aa: aa: aa.
System automatically removes space if there is any space before or
after the newly added IP address.
‐ 39 ‐ System only checks start address if you add IP address. System
check start address and end address if you add IP section and the
end address shall be larger than the start address.
System may check newly added IP address exists or not. System
does not add if input IP address does not exist.
Delete: Click it to remove specified item.
Edit: Click it to edit start address and end address. See Figure 4-62.
System can check the IP address validity after the edit operation and
implement IPv6 optimization.
Default: Click it to restore default setup. In this case, the trusted sites and
blocked sites are both null.
Note:
If you enabled trusted sites, only the IP in the trusted sites list can access
the device.
If you enabled blocked sites, the IP in the blocked sites can not access the
device.
System supports add MAC address.
Multicast
‐ 40 ‐ Here you can set a multiple cast group. Please refer to the following sheet for
detailed information .
IP multiple cast group address -224.0.0.0-239.255.255.255 - “ D” address
space The higher four-bit of the first byte= ” 1110”
Reserved local multiple cast group address -224.0.0.0-224.0.0.255
-TTL=1 W hen sending out telegraph
-For example
224.0.0.1All systems in the sub-net
224.0.0.2All routers in the sub-ne
224.0.0.4DVMRP router
224.0.0.5OSPF router
224.0.0.13 PIMv2 router
Administrative scoped addressees -239.0.0.0-239.255.255.255
-Private address space
Like the single broadcast address of RFC1918
Can not be used in Internet transmission
Used for multiple cast broadcast in limited space.
Except the above mentioned addresses of special meaning, you can use other
addresses. For example:
Multiple cast IP: 235.8.8.36
Multiple cast PORT: 3666.
After you logged in the Web, the Web can automatically get multiple cast
address and add it to the multiple cast groups. You can enable real-time
monitor function to view the view. Please note multiple cast function applies to
special series only.
PPPoE
Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet
service provider). Click save button, you need to restart to activate your
configuration. After rebooting, DVR will connect to internet automatically. The
IP in the PPPoE is the DVR dynamic value.
‐ 41 ‐ DDNS
You need a PC of fixed IP in the internet and there is the DDNS software
running in this PC. In other words, this PC is a DNS (domain name server).
In network DDNS, please select DDNS type and highlight enable item. Them
please input your PPPoE name you get from you IPS and server IP (PC with
DDNS). Click save button and then reboot system. Click save button, system
prompts for rebooting to get all setup activated. After rebooting, open IE and
input as below: http://(DDNS server IP)/(virtual directory name)/webtest.htm
e.g.: http://10.6.2.85/DVR _DDNS/webtest.htm.) Now you can open DDNS
Server web search
Please note NNDS type includes: CN99 DDNS, NO-IP DDNS, Quick DDNS,
Dyndns DDNS and sysdns DDNS. All the DDNS can be valid at the same time,
you can select as you Private DDNS function shall work with special DDNS
server and special Professional Surveillance Software (PSS).
Quick DDNS and Client-end Introduction
‐ 42 ‐ 1) Background Introduction
Device IP is not fixed if you use ADSL to login the network. The DDNS function
allows you to access the DVR via the registered domain name. Besides the
general DDNS ,the Quick DDNS works with the device from the manufacturer
so that it can add the extension function.
2) Function Introduction
The quick DDNS client has the same function as other DDNS client end. It
realizes the bonding of the domain name and the IP address. Right now,
current DDNS server is for our own devices only. You need to refresh the
bonding relationship of the domain and the IP regularly. There is no user name,
password or the ID registration on the server. At the same time, each device
has a default domain name(Generated by MAC address) for your option. You
can also use customized valid domain name (has not registered.).
3) Operation
Before you use Quick DDNS, you need to enable this service and set proper
server address, port value and domain name.
Server address:www.quickddns.com
Port number:80
Domain name :There are two modes: Default domain name and
customized domain name
Except default domain name registration, you can also use customized
domain name (You can input your self-defined domain name.) After
successful registration, you can use domain name to login installed of the
device IP. Do not register frequently. The interval between two
registrations shall be more than 60 seconds. Too many registration
requests may result in server attack. System may take back the domain
name that is idle for one year. You can get a notification email before
the cancel operation if your email address setup is OK.
UPnP
The UPNP protocol is to establish a mapping relationship between the LAN
and the WAN. Please Input the router IP address in the LAN
‐ 43 ‐ UPNP on/off :Turn on or off the UPNP function of the device.
Status: When the UPNP is offline, it shows as “Unknown”. When the
UPNP works it shows “Success”.
Router LAN IP: It is the router IP in the LAN.
WAN IP: It is the router IP in the WAN.
Port Mapping list: The port mapping list here is the one to one
relationship with the router’s port mapping setting.
Service name :Defined by user.
Protocol: Protocol type
Internal port :Port that has been mapped in the router.
External port :Port that has been mapped locally.
Default: UPNP default port setting is the HTTP, TCP and UDP of the
DVR. Add to the list: Click it to add the mapping relationship.
Delete: Click it to remove one mapping item.
Double click one item; you can change the corresponding mapping
information.
Important:
When you are setting the router external port, please use 1024~5000 port.
Do not use well-known port 1~255 and the system port 256~1023 to avoid
conflict. For the TCP and UDP, please make sure the internal port and
external port are the same to guarantee the proper data transmission.
‐ 44 ‐ 3G
Please refer to the following contents for the parameter information
Pane 1: Display 3G signal intensity after you enabled 3G function.
Pane 2: Display 3G module configuration information after you enabled
3G function.
Pane 3: Display 3G module status information after you enabled 3G
function. It is to display current wireless network signal intensity such as
EVDO, CDMA1x, W CDMA, CDMA,EDGE and etc.
3G module: It is to display current wireless network adapter name.
3G Enable/Disable: Check the box here to enable 3G module.
Network type: There are various network types for different 3G network
modules. You can select according to your requirements.
APN: It is the wireless connection server. It is to set you access the
wireless network via which method.
‐ 45 ‐ AUTH: It is the authentication mode. It supports PAP/CHAP.
Dial number: Please input 3G network dialup number you got from your
ISP.
User name: It is the user name for you to login the 3G network.
Password: It is the password for you to login the 3G network.
Pulse interval: You can set dialup duration. Once you disable the extra
stream, the connection time begins. For example, if you input 5 seconds
here, then 3G network connection period is 5 seconds.
The device automatically disconnect when time is up. If there is no extra
stream, 3G Network connection is valid all the time. If the alive time is 0,
then the 3G network connection is valid all the time.
Dial: Here you can enable or disable 3G network connection
/disconnection manually.
3G wireless network: Here is to display wireless network status, SIM card
status, dial status. If the 3G connection is OK, then you can see the device
IP address the wireless network automatically allocates.
WIFI
The W IFI interface is shown as below.
Auto connect W IFI: Check the box here, system automatically connects to
the previous W IFI hotspot.
Refresh: You can click it to search the hotspot list again. It can
automatically add the information such as the password if you have set it
before.
Disconnect: Here you can click it to turn off the connection.
Connect: Here you can click it to connect to the hotspot. System needs to
turn off current connection and then connect to a new hotspot if there is
‐ 46 ‐ connection of you selected one. W IFI working status: Here you can view
current connection status. Please note:
After successful connection, you can see WIFI connection icon at the top
right corner of the preview interface.
When the hotspot verification type is WEP, system displays as AUTO
since the device can not detect its encryption type.
System does not support verification type WPA and WPA2. The display
may become abnormal for the verification type and encryption type.
After device successfully connected to the WIFI, you can view the hotspot
name, IP address, subnet mask default gateway and etc
Email
SMTP server: Please input your email SMTP server IP here.
Port: Please input corresponding port value here.
User name: Please input the user name to login the sender email box.
Password: Please input the corresponding password here.
Sender: Please input sender email box here.
Title: Please input email subject here. System support English character
and Arabic number. Max 32-digit.
Receiver: Please input receiver email address here. System max supports
3 email boxes. System automatically filters same addresses if you input
one receiver. Repeatedly. SSL enable: System supports SSL encryption
box.
Interval: The send interval ranges from 0 to 3600 seconds. 0 means there
is no interval.
Health email enable: Please check the box here to enable this function.
This function allows the system to send out the test email to check the
connection is OK or not.
Interval: Please check the above box to enable this function and then set
the corresponding interval.
System can send out the email regularly as you set here. Click the Test
button, you can see the corresponding dialogue box to see the email
connection is OK or not. Please note system will not send out the email
immediately when the alarm occurs. When the alarm, motion detection or
the abnormity event activates the email, system sends out the email
according to the interval you specified here. This function is very useful
when there are too many emails activated by the abnormity
‐ 47 ‐ FTP
You need to download or buy FTP service tool (such as Ser-U FTP SERVER)
to establish FTP service. Please install Ser-U FTP SERVER first. From “start” ->
“program” -> Serv-U FTP Server ->
Serv-U Administrator. Now you can set user password and FTP folder. Please
note you need to grant write right to FTP upload user
‐ 48 ‐ You can use a PC or FTP login tool to test setup is right or not. For example,
you can login user ZHY to H140H140H140HTUFTP://10.10.7.7UTH and then
test it can modify or delete folder or not . System also supports upload multiple
DVRs to one FTP server. You can create multiple folders under this FTP.
Please highlight the icon front of Enable to activate FTP function. Here you can
input FTP server address, port and remote directory. When remote directory is
null, system automatically create folders according to the IP, time and channel.
User name and password is the account information for you to login the FTP.
File length is upload file length. When setup is larger than the actual file length,
system will upload the whole file. When setup here is smaller than the actual
file length, system only uploads the set length and auto ignore the left section.
When interval value is 0, system uploads all corresponding files. After
completed channel and weekday setup, you can set two periods for one each
channel. Click the Test but ton, you can see the corresponding dialogue box to
see the FTP connection is OK or not.
‐ 49 ‐ Alarm Centre
This interface is reserved for you to develop.
SNMP
SNMP is an abbreviation of Simple Network Management Protocol. It provides
the basic network management frame of the network management system.
The SNMP widely used in many environments. It is used in many network
device, software and system. You can set in the following interface。
‐ 50 ‐ Please enable the SNMP function. Use the corresponding software tool (MIB
Builder and MG-SOFT MIB Browser. You still need two MIB file:
BASE-SNMP-MIB, DVR-SNMP-MIB) to connect to the device.
Please follow the steps listed below to configure.
Check the box to enable the SNMP function. Input the IP address of the
PC than is running the software in the Trap address. You can use default
setup for the rest items.
Compile the above mentioned two MIB file via the software MIB Builder.
Run MG-SOFT MIB Browser to load the file from the previous step to the
software.
Input the device IP you want to manage in the MG-SOFT MIB Browser.
Please set the corresponding version for your future reference.
Open the tree list on the MG-SOFT MIB Browser; you can get the device
configuration. Here you can see the device has how many video
channels, audio channels, application version and etc.
Note
Port conflict occurs when SNMP port and Trap port are the same.
Register
This function allows the device to auto register to the proxy you specified. In
this way, you can use the client-end to access the DVR and etc via the proxy.
Here the proxy has a switch function. In the network service, device supports
the server address of IPv4 or domain.
Please follow the steps listed below to use this function.
Please set proxy server address, port, and sub-device name at the device-end.
‐ 51 ‐ Please enable the auto register function, the device can auto register to the
proxy server.
Important
Do not input network default port such as TCP port number
The proxy server software developed from the SDK. Please open the software
and input the global setup. Please make sure the auto connection port here is
the same as the port you set in the previous step. Now you can add device.
Please do not input default port number such as the TCP port in the mapping
port number. The device ID here shall be the same with the ID you input in
Figure 4 -71. Click Add button to complete the setup. Now you can boot up the
proxy server. When you see the network status is Y, it means your registration
is OK. You can view the proxy server when the device is online.
Important
The server IP address can also be domain. But you need to register a domain
name before you
‐ 52 ‐ Display
Display
Transparency: Here is for you to adjust transparency. The value ranges
from 128 to 255.
Channel name: Here is for you to modify channel name. System max
support 25 -digit (The value may vary due to different series). Please note
all your modification here only applies to DVR local end. You need to open
web or client end to refresh channel name.
Time display: You can select to display time or not when system is
playback.
Channel display: You can select to channel name or not when system is
playback.
Resolution: There are four options: 1920×1080, 1280×1024 (default),
1280×720,1024×768. Please note the system needs to reboot to activate
current setup.
Image enhance: Check the box; you can optimize the margin of the
preview video.
Preview de noise: It is to reduce the video noise and make it clearer. You
can set de noise level. The higher the level is, the clearer the video is.
Please highlight icon to select the corresponding function. After
completing all the setups please click save button, system g oes back to
the previous menu.
‐ 53 ‐ It is to modify channel name.
Channel Type
It is to set channel type. It supports coaxial.
3.3.4 Information
‐ 54 ‐ HDD Information
Here is to list hard disk type, total space, free space, video start time and
status.
SATA: 1 here means system max supports 1 HDD. ○ means current HDD is
normal. X means there is error. - means there is no HDD. If disk is damaged,
system shows as “?”. Please remove the broken hard disk before you add a
new one.
﹡ means the second SN: You can view the HDD amount the device
connected to. HDD is current working HDD
Type: The corresponding HDD properties
Total space: The HDD total capacity
Free space: The HDD free capacity.
Status: HDD can work properly or not.
SMART: Display HDD information
‐ 55 ‐ Double click one HDD information; you can see the HDD SMART information
BPS
Here is for you to view current video data stream (KB/s), resolution and etc.
Log
Here is for you to view system log file. System lists the following information
Log types include system operation, configuration operation, data
management, alarm event, record operation, account manager, log clear, file
operation and etc. It optimized reboot log. There are only three types: normal
reboot, abnormal
‐ 56 ‐ Start time/end time: Pleased select start time and end time, then click
search button. You can view the log files in a list. System max displays
100 logs in one page. It can max save 1024 log files. Please use page
up/down button on the interface or the front panel to view more.
Backup: Please select a folder you want to save; you can click the backup
button to save the log files. After the backup, you can see there is a folder
named Log time on the backup path. Double click the folder, you can see
the log file
Details: Click the Details button or double click the log item, you can view
the detailed information. Here you can use rolling bar to view information,
or you can use Page up/Page down to view other log
Select an item on the list and then click the Details button or double click the
log item, you can view the detailed information such as log time, log type, log
user, IP address and etc
‐ 57 ‐ Version
Here is for you to view some version information such as version number, built
date, serial number and etc
Network
Network Test
‐ 58 ‐ Network test interface is shown。
Destination IP: Please input valid IPV4 address or domain name.
Test: Click it to test the connection with the destination IP address. The
test results can display average delay and packet loss rate and you can
also view the network status as OK , bad, no connection and etc
Network Sniffer backup: Please insert USB2.0 device and click the
Refresh button, you can view the device on the following column. You can
use the dropdown list to select peripheral device. Click Browse button to
select the snap path. The steps here are same as preview backup You
can view all connected network adapter names (including Ethernet,
PPPoE, W IFI, and 3G), you can click the button on the right panel to
begin Sniffer. Click the grey stop button to stop. Please note. system can
not Sniffer several network adapters at the same time. After Sniffer began,
you can exit to implement corresponding network operation such as login
WEB monitor. Please go back to Sniffer interface to click stop Sniffer.
System can save the packets to the specified path. The file is named after
“Network adapter name + time”. You can use software such as Wire shark
to open the packets on the PC for the professional engineer to solve
complicated problems.
Network Load
Network load is shown as follow. Here you can view the follow statistics of the
device network adapter
‐ 59 ‐ Here you can view information of all connected network adapters. The
connection status is shown as offline if connection is disconnected. Click one
network adapter, you can view the flow statistics such as send rate and receive
rate at the top panel
3.3.5 Advanced
You can see HDD Manager, Account, Online User, Auto Maintain, Text
Overlay, Default, Configure.
‐ 60 ‐ HDD Manager
Here is to list hard disk type, total space, free space, video start time and
status.
SATA: 1 here means system max supports 1 HDD. ○ means current HDD
is normal. X means there is error. - means there is no HDD. If disk is
damaged, system shows as “?”. Please remove the broken hard disk
before you add a new one.
SN: You can view the HDD amount the device connected to. ﹡ means
the second HDD is current working HDD.
Type: The corresponding HDD properties.
Total space: The HDD total capacity.
Free space: The HDD free capacity.
Status: HDD can work properly or not.
SMART: Display HDD information
‐ 61 ‐ Double click
Double click
Set HDD Group.
Set HDD Channel.
‐ 62 ‐ Account
Here is for you to implement account management.
Add new user
Modify user
Add group
Modify group
Modify password
For account management please note:
For the user account name and the user group, the string max length is
6-byte. The backspace in front of or at the back of the string is invalid.
There can be backspace in the middle. The string includes the valid
character, letter, number, underline, subtraction sign, and dot.
The default user amount is 64 and the default group amount is 20. System
account adopts two-level management: group and user. No limit to group
or user amount.
For group or user management, there are two levels: admin and user.
The user name and group name can consist of eight bytes. One name can
only be used once.
There are four default users: admin/888888/666666 and hidden user
“default”. Except user 6666, other users have administrator right. Hidden
user “default” is for system interior use only and can not be deleted. When
there is no login user, hidden user “default” automatically login. You can
set some rights such as monitor for this user so that you can view some
channel view without login.
One user should belong to one group. User right can not exceed group
right.
About reusable function: this function allows multiple users use the same
account to login. About user account and MAC. When you add a new user,
you can input the MAC address of current user. Only the user of the
same MAC address can access the device remotely. remotely.(MAC
address is for the device
‐ 63 ‐ of the same LAN.) If you leave MAC address item in blank when you add a
new user, the user of any MAC address can access the device remotely.
You can set or change MAC address when you add or modify a user. The
MAC address function is also valid for PSS login. Please note current
function does not support IPV6.
After all the setups please click save button, system goes back to the previous
menu
Add/Modify User
‐ 64 ‐ Click add user button, Please input the user name, password, select the group
it belongs to from the dropdown list. Then you can check the corresponding
rights for current user. For convenient user management, usually we
recommend the general user right is lower than the admin account.
When you create a new user, you can input the corresponding MAC address of
current user. If you leave this item in blank, any MAC address user can share
this user account to login. Please note system needs to check the validity of
MAC. Only the 12-digit 0-f format address can pass the validity verification。
System only saves small character even you input capitalized one. You can
see the corresponding prompt if there is any illegal input.
Add/Modify Group
‐ 65 ‐ Click add group button, Here you can input group name and then input some
memo information if necessary. There are total 98 rights such as control panel,
shut down, real -time monitor, playback, record, record file backup, PTZ, user
account, system information view, alarm input/output setup, system setup, log
view, clear log, upgrade system, control device and etc.
Online Users
Here is for you to manage online users. You can disconnect one user or block
one user if you have proper system right. Max disconnection setup is 65535
seconds.
System detects there is any newly added or deleted user in each five seconds
and refresh the list automatically.
‐ 66 ‐ Auto Maintain
Here you can set auto-reboot time and auto-delete old files setup. You can set
to delete the files for the specified days
ATM/POS
The ATM/POS function is for financial areas. It includes Sniffer, information
analysis and title overlay function. The Sniffer mode is network. The network
type interface is shown as below. Here we take the ATM/POS protocol to
continue. There are two types: with or without the protocol according to client’s
requirements.
With the protocol
‐ 67 ‐ For ATM/POS with the protocol, you just need to set the source IP, destination
IP (sometimes you need to input corresponding port number
Without the protocol
For the ATM/POS without the protocol, the interface is shown.
Source IP refers to host IP address that sends out information (usually it is the
device host.) Destination IP refers to other systems that receive information.
Usually you do not need to set source port and target port. There are total four
groups IP. The record channel applies to one group (optional) only. Six frame
ID groups verification can guarantee information validity and legal.
‐ 68 ‐ Default
Click default icon, system pops up a dialogue box. You can highlight to restore
default factory
Camera
Network
Event
Storage
System
Please highlight icon to select the corresponding function. After all the setups
please click save button, system goes back to the previous menu.
Warning!
System menu color, language, time display mode, video format, IP address,
user account will not maintain previous setup after default operation!
Backup
DVR support CD-RW, DVD burner, USB device backup, network download
and eSATA. Here we introduce USB, eSATA backup. You can refer to Chapter
5 Web Operation for network download backup operation。
‐ 69 ‐ Click backup button, you can see an interface is shown as in Figure 4-32. Here
is for you to view information. You can view backup device name and its total
space and free space. The device includes CD -RW ,DVD burner, USB device,
flash disk, eSATA backup select backup device and then set channel, file start
time and end time. Click add button, system begins search. All matched files
are listed below. System automatically calculates the capacity needed and
remained. System only backup files with a √ before channel name. You can
use Fn or cancel button to delete √ after file serial number Click Start button,
system begins copy. At the same time, the backup button becomes stop button.
You can view the remaining time and process bar at the left bottom
When the system completes backup, you can see a dialogue box prompting
successful backup
File format: Click the file format; you can see there are two options:
DAV/ASF The file name format usually is: Channel number + Record type
+ Time. In the file name, the YDM
format is Y+M+D+H+M+S. File extension name is .dav
Tips:
During backup process, you can click ESC to exit current interface for other
operation. The system will not terminate backup process.
Note:
When you click stop button during the burning process, the stop function
becomes activated immediately. For example, if there are ten files, when you
click stop system just backup five files, system only save the previous 5 files in
the device (But you can view ten file names).
3.3.6 Shut Down
select Shut Down, you can go to the following interface..
‐ 70 ‐ There are three options: Shutdown/logout/reboot.
For the user who does not have the shut down right, please input
corresponding password to shut down
Slightly difference may be found in the interface due to different series.
4. WEB Operation
4.1 Network Connection
Before web client operation, please check the following items
Network connection is right. DVR and PC network setup is right. Please refer to
network setup(main menu->Setting->Network) Use order ping ***.***.***.***(*
DVR IP address) to check connection is OK or not. Usually the return TTL
value should be less than 255. HDCVI DVR supports various browsers such
as Safari, fire fox browser, Google browser. Device supports multiple-channel
monitor, PTZ control, DVR parameter setup on the Apple PC.
4.2 Login
Open IE and input DVR address in the address column. For example, if your
DVR IP is 192.168.1.108 then please input http:// 192.168.1.108 in IE address
column. System pops up warning information to ask you whether install control
or not. Please click Install button.
‐ 71 ‐ After installation, the interface is shown as below. Please input your user name
and password. Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first
login.
4.3 System menu
4.3.1 Live
In section 2, left click the channel name you want to view, you can see the
corresponding video incurrent window. On the top left corner, you can view
device IP (10.15.6.144), channel number (1), network monitor bit stream
(61Kbps) and stream type: M (Main stream)/S (Sub stream).
‐ 72 ‐ On the top right corer, there are six unction buttons
1: Digital zoom: Click this button and then left drag the mouse in the zone
to zoom in. right click mouse system restores original status.
2: Local record. When you click local record button, the system begins
recording and this button becomes highlighted. You can go to system
folder Record Download to view the recorded file.
3: Snapshot picture. You can snapshoot important video. All images are
memorized in system client folder picture Download (default).
4: Audio :Turn on or off audio.(It has no relationship with system audio
setup )
5: Close video.
There are channel number and one button: Start all. Start all button is to
enable/disable ,all-channel real-time
monitor. Click it the button becomes yellow.
4.3.2 Start dialogue button
You can click this button to enable audio talk. Click【▼】 to select bidirectional
talk mode. There are four options: DEFAULT,G711a,G711u and PCM. After
you enable the bidirectional talk, the Start talk button becomes End Talk button
and it becomes yellow
4.3.3 Instant record button
‐ 73 ‐ Click it, the button becomes yellow and system begins manual record.Click it
again, system restores previous record mode
4.3.4 Local play button
The Web can playback the saved (Extension name is dav) files in the PC -end,
Click local play button, system pops up the following interface for you to select
local play file.
4.3.5 Window change
From left to right, it is to set video quality, video latency, full screen, 1 -window,
4-window.
4.3.6 PTZ control
Before PTZ operation, please make sure you have properly set PTZ protocol
There are eight direction keys. In the middle of the eight direction keys, there is
a 3D intelligent positioning key. Click 3D intelligent positioning key, system
goes back to the single screen mode. Drag the mouse in the screen to adjust
section size. It can realize PTZ automatically. Please refer to the following
sheet for PTZ setup information.
‐ 74 ‐ 4.3.7 Image
Here you can adjust its brightness, contrast, hue and saturation. (Current
channel border becomes green).Or you can click Reset button to restore
system default setup
‐ 75 ‐ 4.4 Setup
4.4.1 Camera Conditions
Here you can view device property information. The setups become valid
immediately after you set.
Please refer to the following sheet for detailed information
Parameter
Function
Channel
Please select a channel from the dropdown list.
Period
It divides one day (24 hours) to two periods. You can set
different hue, brightness, and contrast for different periods.
Hue
It is to adjust monitor video brightness and darkness level. The
default value is 50. The bigger the value is, the large the
contrast between the bright and dark section is and vice versa.
‐ 76 ‐ Brightness
It is to adjust monitor window brightness. The default value is
50. The larger the number is , the bright the video is. When you
input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
value ranges from 0 to 100.The recommended value ranges
from 40 to 60.
Contrast
It is to adjust monitor window contrast. The value ranges from
0 to 100. The default value is 50. The larger the number is, the
higher the contrast is. You can use this function when the
whole video bright is OK but the contrast is not proper. Please
note the video may become hazy if the value is too low. If this
value is too high, the dark section may lack brightness while
the bright section may over exposure .The recommended
value ranges from 40 to 60.
Saturation
It is to adjust monitor window saturation. The value ranges
from 0 to 100. The default value is 50. The larger the number
is, the strong the color is. This value has no effect on the
general brightness of the whole video. The video color may
become too strong if the value is too high. For
4.4.2 Encode
The encode interface is shown as below
Please refer to the following sheet for detailed information.
‐ 77 ‐ Parameter
Function
Channel
Please select a channel from the dropdown list.
Video enable
Code stream
type
Compression
Check the box here to enable extra stream video. This item
is
enabled by default.
It includes main stream, motion stream and alarm stream.
You can select different encode frame rates form different
recorded events. System supports active control frame
function (ACF). It allows you to record in different frame
rates. For example, you can use high frame rate to record
important events, record scheduled event in lower frame
rate and it allows you to set different frame rates for motion
detection record and alarm record.
The main bit stream supports H.264. The extra stream
supports
H.264, MJPG.
Resolution
dropdown list. Please note the option may vary due to
different System supports various resolutions, you can
select from the series.
Frame Rate
Bit Rate
PAL:1~25f/s;NTSC:1~30f/s.
Main stream: You can set bit rate here to change
video quality. The large the bit rate is , the better the
quality is. Please refer to recommend bit rate for the
detailed information.
Extra stream: In CBR, the bit rate here is the max
value. In dynamic video, system needs to low frame rate
or video quality to guarantee the value. The value is null
in VBR mode.
Reference bit
rate
Recommended bit rate value according to the resolution and
frame rate you have set.
I Frame
Here you can set the P frame amount between two I frames.
The value ranges from 1 to 150. Default value is 50.
Recommended value is frame rate *2.
‐ 78 ‐ Audio source
Please select from the dropdown list. There are two options:
Normal/HDCVI. In the normal mode, the audio signal comes
from the Audio In. In the HDCVI mode, the audio signal
comes from the coaxial cable of the camera.
Watermark
enable
This function allows you to verify the video is tampered or
not.
Here you can select watermark bit stream, watermark mode
and watermark character. Default character is Digital CCTV.
The max length is 85-digit. The character can only include
number, character and underline.
Snapshot
Please refer to the following sheet for detailed information.
Parameter
Function
Snapshot
There are two modes: Regular (schedule) and Trigger.
type
Regular snapshot is valid during the specified period
you set.
Trigger snapshot only is valid when motion detect
alarm, tampering alarm or local activation alarm
occurs.
Image size
It is the same with the resolution of the main stream.
Quality
It is to set the image quality. There are six levels.
Interval
I t is to set snapshot frequency. The value ranges from
1s to 7s. Or you can set customized value. The max
setup is 3600s/picture.
Copy
Click it; you can copy current channel setup to other
channel(s).
Video Overlay
The video overlay interface is shown
‐ 79 ‐ Please refer to the following sheet for detailed information
Parameter
Function
Channel
Please select a channel from the dropdown list.
Period
It divides one day (24 hours) to two periods. You can set
different hue, brightness, and contrast for different
periods.
Hue
It is to adjust monitor video brightness and darkness level.
The default value is 50. The bigger the value is, the large
the contrast between the bright and dark section is and
vice versa
Brightness
Contrast
Saturation
It is to adjust monitor window brightness. The default
value is 50. The larger the number is , the bright the video
is. When you input the value here, the bright section and
the dark section of the video will be adjusted accordingly.
You can use this function when the whole video is too
dark or too bright. Please note the video may become
hazy if the value is too high. The value ranges from 0 to
100.The recommended value ranges from 40 to 60.
It is to adjust monitor window contrast. The value ranges
from 0 to 100. The default value is 50. The larger the
number is, the higher the contrast is. You can use this
function when the whole video bright is OK but the
contrast is not proper. Please note the video may become
hazy if the value is too low. If this value is too high, the
dark section may lack brightness while the bright section
may over exposure .The recommended value ranges
from 40 to 60.
It is to adjust monitor window saturation. The value
ranges from 0 to 100. The default value is 50. The larger
‐ 80 ‐ the number is, the strong the color is. This value has no
effect on the general brightness of the whole video. The
video color may become too strong if the value is too high.
For
4.4.2 Encode
The encode interface is shown as below
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel from the dropdown list.
Video enable
Check the box here to enable extra stream video. This
item is enabled by default.
Code stream
It includes main stream, motion stream and alarm
type
stream. You can select different encode frame rates
form different recorded events. System supports active
control frame function (ACF). It allows you to record in
different frame rates. For example, you can use high
frame rate to record important events, record scheduled
event in lower frame rate and it allows you to set
different frame rates for motion detection record and
alarm record
Compression
The main bit stream supports H.264. The extra stream
supports H.264, MJPG.
Resolution
System supports various resolutions, you can select
from the dropdown list. Please note the option may vary
due to different series
‐ 81 ‐ Frame Rate
Bit Rate
PAL:1~25f/s;NTSC:1~30f/s.
Main stream: You can set bit rate here to change
video quality. The large the bit rate is , the better the
quality is. Please refer to recommend bit rate for the
detailed information.
Extra stream: In CBR, the bit rate here is the max
value. In dynamic video, system needs to low frame
rate or video quality to guarantee the value. The value
is null in VBR mode.
Reference
bit rate
I Frame
Recommended bit rate value according to the
resolution and frame rate you have set.
Here you can set the P frame amount between two I
frames. The value ranges from 1 to 150. Default value
is 50. Recommended value is frame rate *2.
Audio source
Please select from the dropdown list. There are two
options: Normal/HDCVI. In the normal mode, the audio
signal comes from the Audio In. In the HDCVI mode,
the audio signal comes from the coaxial cable of the
camera.
Watermark
enable
This function allows you to verify the video is tampered
or not. Here you can select watermark bit stream,
watermark mode and watermark character. Default
character is Digital CCTV. The max length is 85-digit.
The character can only include number, character and
underline.
Snapshot
Please refer to the following sheet for detailed information.
Parameter
Function
Snapshot
There are two modes: Regular (schedule) and Trigger.
type
Regular snapshot is valid during the specified period
you set.
‐ 82 ‐ Trigger snapshot only is valid when motion detect
alarm, tampering alarm or local activation alarm occurs.
Image size
Quality
Interval
Copy
It is the same with the resolution of the main stream.
It is to set the image quality. There are six levels.
It is to set snapshot frequency. The value ranges from 1s
to 7s. Or you can set customized value. The max setup is
3600s/picture.
Click it; you can copy current channel setup to other
channel(s).
Video Overlay
The video overlay interface is shown
Please refer to the following sheet for detailed information
Parameter
Cover-area
Time Title
Function
Check Preview or Monitor first.
Click Set button, you can privacy mask the specified video in
the preview or monitor video.
System max supports 4 privacy mask zones.
You can enable this function so that system overlays time
information in video window.
You can use the mouse to drag the time title position.
You can view time title on the live video of the WEB or the
playback video.
‐ 83 ‐ Channel
Title
You can enable this function so that system overlays channel
information in video window.
You can use the mouse to drag the channel title position.
You can view channel title on the live video of the WEB or the
playback video.
Path
The storage path interface is shown
Here you can set snap image saved path and the record storage path. The
default setup is C:\PictureDownload and C:\RecordDownload.Please click the
Save button to save current setup.
Channel Name
Here you can set channel name
4.4.3 Network
TCP/IP
‐ 84 ‐ Please refer to the following sheet for detailed information.
Parameter
Mode
Mac
Address
IP Version
IP Address
Function
There are two modes: static mode and the DHCP mode.
The IP/submask/gateway are null when you select the
DHCP mode to auto search the IP.
If you select the static mode, you need to set the
IP/submask/gateway manually.
If you select the DHCP mode, you can view the
IP/submask/gateway from the DHCP.
If you switch from the DHCP mode to the static mode,
you need to reset the IP parameters.
Besides, IP/submask/gateway and DHCP are read-only
when the PPPoE dial is OK.
It is to display host Mac address.
It is to select IP version. IPV4 or IPV6. You can access
the IP address of these two versions.
Please use the keyboard to input the corresponding
number to modify the IP address and then set the
corresponding subnet mask and the default gateway.
DNS IP address.
Preferred
DNS
Alternate
Alternate DNS IP address.
DNS
For the IP address of IPv6 version, default gateway, preferred DNS and
alternate DNS, the input value shall be 128-digit. It shall not be left in
blank.
LAN load
System can process the downloaded data first if you
enable this function. The download speed is 1.5X or 2.0X
of the normal speed.
Connection
‐ 85 ‐ Please refer to the following sheet for detailed information.
Parameter
Function
Max
connection
It is the max Web connection for the same device. The value
ranges from 1 to 120. The default setup is 120.
TCP port
The default value is 37777. You can input the actual port
number if necessary.
UDP port
The default value is 37778. You can input the actual port
number if necessary.
HTTP port
The default value is 80. You can input the actual port
number if necessary.
HTTPS
The default value is 443. You can input the actual port
number if necessary.
RTSP port
The default value is 554.
WIFI
Please note this function is for the device of WIFI module.
‐ 86 ‐ Please check the box to enable WIFI function and then click the Search SSID
button. Now you can view all the wireless network information in the following
list. Double click a name to connect to it. Click Refresh button, you can view
latest connection status.
3G
CDMA/GPRS
Please refer to the following sheet for detailed information.
Parameter
Function
WLAN type
Here you can select 3G network type to distinguish the 3G
module from different ISP. The types include WCDMA,
CDMA1x and etc.
APN/Dial
No.
Here is the important parameter of PPP.
‐ 87 ‐ Authorization
It includes PAP,CHAP,NO_AUTH.
Pulse
interval
It is to set time to end 3G connection after you close xtra
stream monitor. For example, if you input 60 here, system
ends 3G connection after you close extra stream monitor 60
seconds.
Mobile
Here you can activate or turn off the 3G connected phone or mobile phone, or
the phone you set to get alarm message.
PPPoE
Input the PPPoE user name and password you get from the IPS (internet
service provider) and enable PPPoE function. Please save current setup and
then reboot the device to get the setup activated. Device connects to the
internet via PPPoE after reboot. You can get the IP address in the WAN from
the IP address column. Please note, you need to use previous IP address in
the LAN to login the device. Please go to the IP address item to via the device
current device information. You can access the client-end via this new address.
DDNS
The DDNS is to set to connect the various servers so that you can access the
system via the server. Please go to the corresponding service website to apply
a domain name and then access the system via the domain. It works even your
IP address has changed. Please select DDNS from the dropdown list (Multiple
‐ 88 ‐ choices). Before you use this function, please make sure your purchased
device support current function.
Please refer to the following sheet for detailed information.
Parameter
Function
Server
Type
You can select DDNS protocol from the dropdown list and then
enable DDNS function.
Server IP
DDNS server IP address
Server Port
DDNS server port.
Domain
Name
User
Your self-defined domain name.
The user name you input to log in the server.
Password
The password you input to log in the server.
Update
period
Device sends out alive signal to the server regularly. You can
set interval value between the device and DDNS server here.
Quick DDNS and Client-end Introduction
1) Background Introduction Device IP is not fixed if you use ADSL to login the
network. The DDNS function allows you to access the DVR via the registered
domain name. Besides the general DDNS, the quick DDNS works with the
device from the manufacturer so that it can add the extension function.
2) Function Introduction The quick DDNS client has the same function as other
DDNS client end. It realizes the bonding of the domain name and the IP
address. Right now, current DDNS server is for our own devices only. You
need to refresh the bonding relationship of the domain and the IP regularly.
There is no user name, password or the ID registration on the server. At the
same time, each device has a default domain name (Generated by MAC
address) for your option. You can also use customized valid domain name (has
not registered.). 3) Operation Before you use Quick DDNS, you need to enable
this service and set proper server address, port value and domain name
‐ 89 ‐ Server address:www.quickddns.com
Port number:80
Domain name:There are two modes: Default domain name and
customized domain name Except default domain name registration, you can
also use customized domain name (You can input your self-defined domain
name.) After successful registration, you can use domain name to login
installed of the device IP.
User name: It is optional. You can input your commonly used email
address.
Important
Do not register frequently. The interval between two registrations shall
be more than 60 seconds. Too many registration requests may result in server
attack.
System may take back the domain name that is idle for one year. You
can get a notification email before the cancel operation if your email address
setup is OK.
IP filter
After you enabled trusted sites function, only the IP listed below can access
current DVR. If you enable blocked sites function, the following listed IP
addresses can not access current DVR.
‐ 90 ‐ Email
Please refer to the following sheet for detailed information.
Parameter
Function
Enable
Please check the box here to enable email function.
SMTP Server
Input server address and then enable this function.
Port
Default value is 25. You can modify it if necessary.
Anonymity
For the server supports the anonymity function. You can
auto login anonymously. You do not need to input the
user name. password and the sender information.
User Name
The user name of the sender email account.
Password
The password of sender email account.
Sender
Sender email address.
‐ 91 ‐ Authentication
(Encryption
mode)
You can select SSL or none.
Subject
Input email subject here.
Attachment
System can send out the email of the snapshot picture
once you check the box here.
Receiver
Input receiver email address here. Max three addresses.
It supports SSL, TLS email box.
Interval
The send interval ranges from 0 to 3600 seconds.
0means there is no interval. Please note system will not
send out the email immediately when the alarm occurs.
When the alarm, motion detection or the abnormity event
activates the email, system sends out the email
according to the interval you specified here. This
function is very useful when there are too many
emails activated by the abnormity events, which may
result in heavy load for the email server.
Health mail
Please check the box here to enable this function.
Parameter
Function
Enable
Please check the box here to enable email function.
SMTP
Server
Health mail
enable
Update
period
(interval)
Input server address and then enable this function.
Email test
The system will automatically sent out a email once to test
the connection is OK or not .Before the email test, please
save the email setup information.
Please check the box here to enable this function.
This function allows the system to send out the test email to
check the connection is OK or not. Please check the box to
enable this function and then set the corresponding interval.
System can send out the email regularly as you set here.
Health
mail
Please check the box here to enable this function.
Enable
Please check the box here to enable email function.
‐ 92 ‐ SMTP
Server
Input server address and then enable this function.
Health
mail
enable
Update
period
(interval)
Please check the box here to enable this function.
Email test
The system will automatically sent out a email once to test
the connection is OK or not .Before the email test, please
save the email setup information.
This function allows the system to send out the test email
to check the connection is OK or not. Please check the
box to enable this function and then set the corresponding
interval. System can send out the email regularly as you
set here.
FTP
It is to set FTP IP, port and etc for remote storage.
UPnP
It allows you to establish the mapping relationship between the LAN and the
public network. Here you can also add, modify or remove UPnP item. In the
Windows OS, From Start->Control Panel->Add or remove programs. Click the
“Add/Remove Windows Components” and then select the “Network Services”
from the Windows Components Wizard.
‐ 93 ‐ Click the Details button and then check the “Internet Gateway Device
Discovery and Control client ”and “UPnP User Interface”. Please click OK
to begin installation.
Enable UPnP from the Web. If your UPnP is enabled in the Windows
OS, the DVR can auto detect it via the “My Network Places”
SNMP
The SNMP allows the communication between the network management work
station software and the proxy of the managed device. It is reserved for the 3rd
party to develop.
Please refer to the following sheet for detailed information.
‐ 94 ‐ Read
Community
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same. The read community will read all
the objects the SNMP supported in the specified name. The
default setup is public.
Write
Community
It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same. The read community will
read/write/access all the objects.
SNMP Port
The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to
65535.The default value is 161SNMP supported in the
specified name. The default setup is write.
Trap
address
Trap port
The destination address of the Trap information from the proxy
program of the device.
The destination port of the Trap information from the proxy
program of the device. It is for the gateway device and the
client-end PC in the LAN to exchange the information. It is
anon-protocol connection port. It has no effect on the network
applications. It is a UDP port not TCP port. The value ranges
from 1 to 165535. The default value is 162.
Check V1, system only processes the information of V1.
Check V2, system only processes the information of V2.
SNMP
version
Multicast
Multicast is a transmission mode of data packet. When there is multiple-host to
receive the same data packet, multiple-cast is the best option to reduce the
broad width and the CPU load. The source host can just send out one data to
transit. This function also depends on the relationship of the group member
and group of the outer.
‐ 95 ‐ Auto Register
This function allows the device to auto register to the proxy you specified. In
this way, you can use the client-end to access the DVR and etc via the proxy.
Here the proxy has a switch function. In the network service, device supports
the server address of IPv4 or domain. Please follow the steps listed below to
use this function. Please set proxy server address, port, and sub-device name
at the device-end. Please enable the auto register function, the device can auto
register to the proxy server.
Alarm Centre
This interface is reserved for you to develop. System can upload alarm signal
to the alarm centre when local alarm occurs. Before you use alarm centre,
please set server IP, port and etc. When an alarm occurs, system can send out
data as the protocol defined, so the client-end can get the data.
‐ 96 ‐ HTTPS
In this interface, you can set to make sure the PC can successfully login via the
HTTPS. It is to guarantee communication data security. The reliable and stable
technology can secure the user information security and device safety.
Note:
You need to implement server certificate again if you have changed device IP.
You need to download root certificate if it is your first time to use HTTPS on
current PC
Create Server Certificate If it is your first time to use this function, please
follow the steps listed below.
click
button, input country name, state name
and etc. Click Create button.
Note: Please make sure the IP or domain information is the same as your
device IP or domain name
You can see the corresponding prompt. Now the server certificate is
successfully created.
‐ 97 ‐ Download root certificate
Click
box.
button, system pops up a dialogue
Click Open button, you can go to the following interface.
‐ 98 ‐ Click Install certificate button, you can go to certificate wizard.
Click Next button to continue. Now you can select a location for the certificate.
‐ 99 ‐ Click Next button, you can see the certificate import process is complete
Click Finish button, you can see system pops up a security warning dialogue
box.
‐ 100 ‐ Click Yes button, system pops up the following dialogue box, you can see the
certificate download is complete.
View and set HTTPS port From Setup->Network->Connection, you can see
the following interface. You can see HTTPS default value is 443.
Login
Open the browser and then input https://xx.xx.xx.xx:port. xx.xx.xx.xx: is your
device IP or domain mane.
Port is your HTTPS port. If you are using default HTTPS value 443, you do not
need to add port information here. You can input https://xx.xx.xx.xx to access.
Now you can see the login interface if your setup is right.
4.4.4 Event Video detect
1. Motion Detect
The motion detect interface is shown as below
‐ 101 ‐ ‐ 102 ‐ Please refer to the following sheet for detailed information.
Parameter
Function
Enable
You need to check the box to enable motion detection function.
Please select a channel from the dropdown list.
‐ 103 ‐ Period
Motion detection function becomes activated in the specified
periods. See Figure 5-48. There are six periods in one day.
Please draw a circle to enable corresponding period. Click OK
button, system goes back to motion detection interface, please
click save button to exit.
Anti-dither
System only memorizes one event during the anti-dither
period. The value ranges from 5s to 600s.
Sensitivity
There are six levels. The sixth level has the highest sensitivity.
Region
If you select motion detection type, you can click this button to
set motion detection zone. The interface is shown as in Figure
5-49.
Here you can set motion detection zone. There are
four zones for you to set. Please select a zone first and then
left drag the mouse to select a zone. The corresponding
color zone displays different detection zone. You can click
Fn button to switch between the arm mode and disarm
mode. In arm mode, you can click the direction buttons to
move the green rectangle to set the motion detection zone.
After you completed the setup, please click ENTER button
to exit current setup. Do remember click save button to save
current setup. If you click ESC button to exit the region setup
interface system will not save your zone setup.
Record
channel
System auto activates motion detection channel(s) to record
once an alarm occurs. Please note you need to set motion
detect record period and go to Storage-> Schedule to set
current channel as schedule record.
Record
Delay
Alarm out
System can delay the record for specified time after alarm
ended. The value ranges from 10s to 300s.
Enable alarm activation function. You need to select alarm
output port so that system can activate corresponding alarm
device when an alarm occurs.
System can delay the alarm output for specified time after an
alarm ended. The value ranges from 1sto 300s.
Latch
Show
message
System can pop up a message to alarm you in the local host
screen if you enabled this function.
Buzzer
Check the box here to enable this function. The buzzer beeps
when an alarm occurs.
‐ 104 ‐ Alarm
upload
System can upload the alarm signal to the centre (Including
alarm centre.
Message
When 3G network connection is OK, system can send out a
message when motion detect occurs.
Send
Email
If you enabled this function, System can send out an email to
alert you when an alarm occurs.
Tour
You need to check the box here to enable this function. System
begins 1-wiindow or multiple-window tour display among the
channel(s) you set to record when an alarm occurs.
Video Loss
After analysis video, system can generate a video loss alarm when the
detected moving signal reached the sensitivity you set here. Please note video
loss does not support anti-dither, sensitivity, region setup. For rest setups,
please refer to chapter 5.8.3.1.1 motion detect for detailed information.
Tampering
After analysis video, system can generate a tampering alarm when the
detected moving signal reached the sensitivity you set here. For detailed
setups, please refer to chapter 5.8.3.1.1 motion detect for detailed information.
‐ 105 ‐ Abnormality It includes two types: No Storage, Storage error, HDD no space,
net disconnection, IP conflict and MAC conflict.
Please refer to the following sheet for detailed information.
Parameter
Function
Event
Type
The abnormal events include: No disk, disk error, disk no
space, net disconnection, IP conflict and MAC conflict. You
can set one or more items here. Less than: You can set the
minimum percentage value here (For disk not space only). The
device can alarm when capacity is not sufficient. You need to
draw a circle to enable this function.
Enable
Check the box here to enable selected function.
Alarm Out
Please select corresponding alarm output channel when an
alarm occurs. You need to check the box to enable this
function.
‐ 106 ‐ Latch
The alarm output can delay for the specified time after an
alarm stops. The value ranges from 1s to 300s.
Show
message
System can pop up a message to alarm you in the local host
screen if you enabled this function.
Alarm
upload
System can upload the alarm signal to the centre (Including
alarm centre.
Send
Email
If you enabled this function, System can send out an email to
alert you when an alarm occurs.
Buzzer
Check the box here to enable this function. The buzzer beeps
when an alarm occurs.
4.4.5 Storage Schedule
In this interfaces, you can add or remove the schedule record/snapshot setup.
There are three record modes: general (auto), motion detect and alarm. There
are six periods in one day. You can view the current time period setup from the
color bar.
Green color stands for the general record/snapshot.
Yellow color stands for the motion detect record/snapshot..
Red color stands for the alarm record/snapshot.
Blue color stands for MD&alarm record/snapshot.
‐ 107 ‐ Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Please select a channel from the dropdown list.
Pre-record
Please input pre-record time here. The value ranges from 0
to 30.
Check the box here to enable redundancy function. Please
note this function is null if there is only one HDD.
Redundancy
Snapshot
Check the box here to enable snapshot function.
Holiday
Check the box here to enable holiday function.
Setup
(Sunday to
Saturday)
Click the Setup button, you can set record period. See
Figure 5-56. There are six periods in one day. If you do not
check the date at the bottom of the interface, current setup
is for today only. Please click Save button and then exit.
‐ 108 ‐ Setup
(Holiday)
Click the Setup button, you can set record period. See
Figure 5-56. There are six periods in one day. If you check
Holiday box, current channel shall record as your holiday
setup here.
Copy
Copy function allows you to copy one channel setup to
another. After setting in channel, click Copy button, you can
go to interface Figure 5-57. You can see current channel
name is grey such as channel 1. Now you can select the
channel you wan to paste such as channel 5/6/7. If you wan
to save current setup of channel 1 to all channels, you can
click the first box “ALL”. Click the OK button to save current
copy setup. Click the OK button in the Encode interface, the
copy function succeeded.
4.4.6 Local Storage
Here you can see HDD information. You can also operate the read-only,
read-write, redundancy (if there are more than on HDD) and format operation.
4.4.7 Record
Please refer to the following sheet for detailed information.
‐ 109 ‐ Parameter
Function
Channel
Here you can view channel number. The number displayed
here is the max channel amount of your device.
There are three statuses: schedule, manual and stop.
Status
Schedule
Manual
Stop
Start all/ stop
all
System enables auto record function as you set in record
schedule setup (general, motion detect and alarm).
It has the highest priority. Enable corresponding channel to
record no matter what period applied in the record setup.
Stop current channel record no matter what period applied in
the record setup.
Check the corresponding All button, you can enable or disable
all channels record.
4.4.8 Setting General
The general interface includes general, date/time and holiday setup.
5.8.5.1.1General
Please refer to the following sheet for detailed information.
Parameter
Function
Device ID
It is to set device name.
Device No.
It is device channel number.
Language
You can select the language from the dropdown list. Please
note the device needs to reboot to get the modification
activated.
‐ 110 ‐ Video
Standard
This is to display video standard such as PAL.
HDD full
Here is for you to select working mode when hard disk is full.
There are two options: stop recording or rewrite. If current
working HDD is overwritten or the current HDD is full while the
next HDD is no empty, then system stops recording, If the
current HDD is full and then next HDD is not empty, then
system overwrites the previous files.
Pack
duration
Here is for you to specify record duration. The value ranges
from 1 to 120 minutes. Default value is 60 minutes.
Date and time
Please refer to the following sheet for detailed information.
Parameter
Function
Date
format
Time
Format
Here you can select date format from the dropdown list.
Time zone
The time zone of the device.
There are two options: 24-H and 12-H.
‐ 111 ‐ System
time
It is to set system time. It becomes valid after you set.
Sync PC
You can click this button to save the system time as your PC
current time.
DST
Here you can set day night save time begin time and end time.
You can set according to the date format or according to the
week format.
NTP
You can check the box to enable NTP function.
NTP
server
Port
You can set the time server address.
It is to set the time server port.
Interval
It is to set the sync periods between the device and the time
server.
Holiday Setup
Here you can click Add box to add a new holiday and then click Save button to
save.
Display
Display interface includes GUI, TV adjust, Tour and zero-channel encoding.
Display
Here you can set background color and transparency level.
‐ 112 ‐ Please refer to the following sheet for detailed information.
Parameter
Resolution
Transparency
Time
title/channel
title
Image
enhance
Function
There are four options:
1920×1080,1280×1024(default),1280×720,1024×768. Please
note the system needs to reboot to activate current setup.
Here is for you to adjust transparency. The value ranges from
128 to 255.
Check the box here, you can view system time and channel
number on the monitor video.
Check the box; you can optimize the margin of the preview
video.
Tour
Here you can set tour interval, split mode, motion detect tour and alarm tour
mode.
‐ 113 ‐ Please refer to the following sheet for detailed information.
Parameter
Enable tour
Interval
Split
Motion
tour/Alarm tour
Enable
Compression
Resolution
Function
Check the box here to enable tour function.
Here is for you to adjust transparency. The value ranges
from 5 to120s.The default setup is 5s.
Here you can set window mode and channel group.
System cansupport1/4/8-window according to device
channel amount.
Here you can set motion detect tour/alarm tour window
mode. System supports 1/8-window now.
Check the box here to enable zero-channel function.
System supports H.264.
Please select from the dropdown list. System supports
D1/CIF/QCIF and etc.
Frame rate
Please select from the dropdown list. The value ranges
from 1-25(PAL) or 1-30(NTSC).
Bit rate
Please select from the dropdown list.
PTZ
‐ 114 ‐ Before setup, please check the following connections are right
Please refer to the following sheet for detailed information.
Parameter
Function
Channel
Select speed dome connected channel.
Control
mode
You can select control mode from the dropdown list. There are
two options: Serial/HDCVI. For HDCVI series product, please
select HDCVI. The control signal is sent to the PTZ via the
coaxial cable. For the serial mode, the control signal is sent to
the PTZ via the RS485 port.
Protocol
Address
Baud Rate
Data Bit
Please select protocol as DH-SD1 if you are using HDCVI
mode.
Set corresponding dome address. Default value is 1. Please
note your setup here shall comply with your dome address;
otherwise you can not control the speed dome.
Select the dome baud rate. Default setup is 9600.
Default setup is 8. Please set according to the speed dome dial
switch setup.
Stop bit
Default setup is 1. Please set according to the speed dome dial
switch setup.
Parity
Default setup is none. Please set according to the speed dome
dial switch setup.
ATM/POS
The ATM/POS function is for financial areas. It includes Sniffer, information
analysis and title overlay function. The Sniffer mode is network. The network
type interface is shown as below. Here we take the ATM/POS protocol to
continue. There are two types: with or without the protocol according to client’s
requirements with the protocol . For ATM/POS with the protocol, you just need
‐ 115 ‐ to set the source IP, destination IP (sometimes you need to input
corresponding port number).
Source IP refers to host IP address that sends out information (usually it is the
device host.) Destination IP refers to other systems that receive information.
Usually you do not need to set source port and target port. There are total four
groups IP. The record channel applies to one group (optional) only. Six frame
ID groups verification can guarantee information validity and legal.
Account
Note:
For the character in the following user name or the user group name, system
max supports 6-digits.The space in the front or at the end of the string is null.
The valid string includes: character, number, and underline.
The user amount default setup is 64 and the group amount default setup is
20. The factory default setup includes two levels: user and admin. You can
set the corresponding group and then set the rights for the respective user in
the specified groups.
User management adopts group/user modes. The user name and the group
name shall be unique One user shall be included in only one group.
User name
In this interface you can add/remove user and modify user name.
Add user: It is to add a name to group and set the user rights. There are four
‐ 116 ‐ default users: admin/888888/666666 and hidden user “default”. Except user
6666, other users have administrator right. The user 666666 can only have the
monitor rights,. Hidden user “default” is for system interior use only and can not
be deleted. When there is no login user, hidden user “default” automatically
login. You can set some rights such as monitor for this user so that you can
view some channel view without login. Here you can input the user name and
password and then select one group for current user. Please note the user
rights shall not exceed the group right setup.
For convenient setup, please make sure the general user has the lower rights
setup than the admin
Modify user It is to modify the user property, belonging group, password and
rights. Modify password It is to modify the user password. You need to input
the old password and then input the new password twice to confirm the new
setup. Please click the OK button to save. Please note, the password ranges
from 1-digit to 6-digit. It shall include the number only. For the user of the
account rights, he can modify the password of other users.
‐ 117 ‐ Group
The group management interface can add/remove group, modify group
password and etc.
Add group: It is to add group and set its corresponding rights. Please input the
group name and then check the box to select the corresponding rights. It
includes: shutdown/reboot device, live view, record control, PTZ control and
etc.
‐ 118 ‐ Modify group
Click the modify group button, Here you can modify group information such as
remarks and rights.
Auto maintain
Here you can select auto reboot and auto delete old files interval from the
dropdown list. If you want to use the auto delete old files function, you need to
set the file period. Click Manual reboot button, you can restart device manually.
‐ 119 ‐ Import/Export
Please refer to the following sheet for detailed information.
Parameter Function
Import
It is to import the local setup files to the system.
Export
It is to export the corresponding WEB setup to your local PC.
Default
Here you can select Channel/Network/Event/Storage/System. Or you can
check the All box to select all items
Upgrade
Please select the upgrade file and then click the update button to begin update.
Please note the file name shall be as *.bin. During the upgrade process, do not
unplug the power cable, network cable, or shutdown the device.
Important
Improper upgrade program may result in device malfunction!
‐ 120 ‐ Version
Here you can view record channel, alarm input/output information, software
version, release date and etc. Please note the following information is for
reference only.
Log
Please refer to the following sheet for log parameter information.
Parameter
Type
Start time
End time
Search
Detailed
information
Clear
Backup
Online User
Function
Log types include: system operation, configuration
operation, data operation, event operation, record operation,
user management, log clear.
Set the start time of the requested log.
Set the end time of the requested log.
You can select log type from the drop down list and then
click search button to view the list. You can click the stop
button to terminate current search operation.
You can select one item to view the detailed information.
You can click this button to delete all displayed log files.
Please note system does not support clear by type.
You can click this button to backup log files to current PC.
‐ 121 ‐ Playback
Click Playback button, Please set record type, record date, window display
mode and channel name. You can click the date on the right pane to select the
date. The green highlighted date is system current date and the blue
highlighted date means it has record files.
Then please click File list button, you can see the corresponding files in the list.
Select a file you want to play and then click Play button, system can begin
‐ 122 ‐ playback. You can select to playback in full-screen. Please note for one
channel, system can not playback and download at the same time. You can
use the playback control bar to implement various operations such as play,
pause, stop, slow play, fast play and etc.
Select the file(s) you want to download and then click download button, The
Download button becomes Stop button and there is a process bar for your
reference. Please go to you default file saved path to view the files.
Load more It is for you to search record or picture. You can select record
channel, record type and record time to download. There are two download
types.
‐ 123 ‐ Watermark
Please select a file and then click Verify button to see the file has been
tampered with or not
4.6 Alarm
Click alarm function, Here you can set device alarm type and alarm sound
setup (Please make sure you have enabled audio function of corresponding
alarm events.).
‐ 124 ‐ Please refer to the following sheet for detailed information.
Type
Parameter
Function
Alarm
Video loss
System alarms when video loss occurs.
Type
Motion
System alarms when motion detection
detection
alarm occurs.
Tampering
System alarms when camera is viciously
masking.
Disk full
System alarms when disk is full.
Disk error
System alarms when disk error occurs.
External
Alarm input device sends out alarm.
alarm
Operation
Prompt
Check the box here, system can
automatically pops up an alarm icon on the
Alarm button in the main interface when
there is an alarm.
Alarm
Play alarm
System sends out alarm sound when an
Sound
sound
alarm occurs. You can specify as you wish.
Sound
Here you can specify alarm sound file.
path
4.7 Log out
Click log out button, system goes back to log in interface. You need to input
user name and password to login again.
‐ 125 ‐ 4.8 Un-install Web Control
You can use web un-install tool “uninstall web.bat” to un-install web control.
Please note, before you un-installation, please close all web pages, otherwise
the un-installation might result in error.
5. Professional Surveillance System
Besides Web, you can use our Professional Surveillance Software (PSS) to
login the device. For detailed information, please refer to VMS user’s manual.
6. FAQ
6.1 FAQ
1.DVR can not boot up properly.
There are following possibilities:
Input power is not correct.
Power connection is not correct.
Power connection is not correct.
Program upgrade is wrong.
HDD malfunction or something wrong with HDD ribbon.
Seagate DB35.1,DB35.2,SV35 or Maxtor 17-g has compatibility problem.
Please upgrade to the latest version to solve this problem.
Front panel error.
Main board is damaged. 
2. DVR often automatically shuts down or stops running.
There are following possibilities Input voltage is not stable or it is too low.
‐ 126 ‐ HDD malfunction or something wrong with the ribbon.
Button power is not enough.
Front video signal is not stable.
Working environment is too harsh, too much dust.
Hardware malfunction.
3. System can not detect hard disk.
There are following possibilities:
HDD is broken.
HDD ribbon is damaged.
HDD cable connection is loose.
Main board SATA port is broken.
4. There is no video output whether it is one-channel, multiple-channel or
all-channel output.
There are following possibilities:
Program is not compatible. Please upgrade to the latest version.
Brightness is 0. Please restore factory default setup.
There is no video input signal or it is too weak.
Check privacy mask setup or your screen saver.
DVR hardware malfunctions.
5. Real-time video color is distorted.
There are following possibilities:
When using BNC output, NTSC and PAL setup is not correct. The real-time
video becomes
black and white.
DVR and monitor resistance is not compatible.
Video transmission is too long or degrading is too huge.
DVR color or brightness setup is not correct.
6. Can not search local records.
There are following possibilities:
HDD ribbon is damaged.
HDD is broken.
Upgraded program is not compatible.
The recorded file has been overwritten.
Record function has been disabled
‐ 127 ‐ 7. Video is distorted when searching local records.
There are following possibilities:
Video quality setup is too low.
Program read error, bit data is too small. There is mosaic in the full screen.
Please restart the
DVR to solve this problem.
HDD data ribbon error.
HDD malfunction.
DVR hardware malfunctions.
8. There is no audio when monitor.
There are following possibilities.
It is not a power picker.
It is not a power acoustics.
Audio cable is damaged.
DVR hardware malfunctions.
9. There is audio when monitor but there is no audio when system
playback.
There are following possibilities:
Setup

is not correct. Please enable audio function
Corresponding channel has no video input. Playback is not continuous when
the screen is blue.
10. Time display is not correct.
There are following possibilities:
Setup is not correct
Battery contact is not correct or voltage is too low.
Crystal is broken.
11. DVR can not control PTZ.
There are following possibilities:
Front panel PTZ error
PTZ decoder setup, connection or installation is not correct.
Cable connection is not correct.
PTZ setup is not correct.
PTZ decoder and DVR protocol is not compatible.
When there are several decoders, please add 120 Ohm between the PTZ
‐ 128 ‐ decoder A/B cables furthest end to delete the reverberation or impedance
matching. Otherwise the PTZ control is not stable.
The distance is too far.
12. Motion detection function does not work.
There are following possibilities:
Period setup is not correct.
Motion detection zone setup is not correct.
Sensitivity is too low.
For some versions, there is hardware limit.
13. Can not log in client-end or web.
There are following possibilities:
For Windows 98 or Windows ME user, please update your system to
Windows 2000 sp4. Or you can install client-end software of lower version.
Please note right now, our DVR is not compatible with Windows VISTA
control.
ActiveX control has been disabled.
No dx8.1 or higher. Please upgrade display card driver.
Network connection error.
Network setup error.
Password or user name is invalid.
Client-end is not compatible with DVR program.
14. There is only mosaic no video when preview or playback video file
remotely.
There are following possibilities:
Network fluency is not good.
Client-end resources are limit.
There is multiple-cast group setup in DVR. This mode can result in mosaic.
Usually we do not recommend this mode.
There is privacy mask or channel protection setup.
Current user has no right to monitor.
DVR local video output quality is not good.
15. Network connection is not stable.
There are following possibilities:
Network is not stable.
IP address conflict.
‐ 129 ‐ MAC address conflict.
PC or DVR network card is not good.
16. Burn error /USB back error.
There are following possibilities:
Burner and DVR are in the same data cable.
System uses too much CPU resources. Please stop record first and then
begin backup.
Data amount exceeds backup device capacity. It may result in burner error.
Backup device is not compatible.
Backup device is damaged. 
17. Keyboard can not control DVR.
There are following possibilities:
DVR serial port setup is not correct.
Address is not correct.
When there are several switchers, power supply is not enough.
Transmission distance is too far. 
18. Alarm signal can not been disarmed.
There are following possibilities:
Alarm setup is not correct.
Alarm output has been open manually.
Input device error or connection is not correct.
Some program versions may have this problem. Please upgrade your
system.
19. Alarm function is null.
There are following possibilities.
Alarm setup is not correct.
Alarm cable connection is not correct.
Alarm input signal is not correct.
There are two loops connect to one alarm device. 
21. Record storage period is not enough.
There are following possibilities:
Camera quality is too low. Lens is dirty. Camera is installed against the light.
Camera aperture setup is not correct
HDD

capacity is not enough.
‐ 130 ‐ HDD is damaged.
22. Can not playback the downloaded file. There are following
possibilities:
There is no media player.
No DXB8.1 or higher graphic acceleration software.
There is no DivX503Bundle.exe control when you play the file
transformed to AVI via media player.
No DivX503Bundle.exe or ffdshow-2004 1012 .exe in Windows XP OS
23. Forgot local menu operation password or network password
Please contact your local service engineer or our sales person for help. We
can guide you to solve this problem.
24. When I login via HTTPS, a dialogue says the certificate for this
website is for other address.
Please follow chapter 5.8.2.15.1 to create server certificate.
25. When I login via HTTPS, a dialogue says the certificate is not trusted.
Please follow chapter 5.8.2.15.2 to download root certificate.
26. When I login via HTTPS, a dialogue says the certificate has expired or
is not valid yet.
Please make sure your PC time is the same as the device time.
6.2 Daily Maintenance
Please use the brush to clean the board, socket connector and the
chassis regularly.
The device shall be soundly earthed in case there is audio/video
disturbance. Keep the device away from the static voltage or induced voltage.
Please unplug the power cable before you remove the audio/video
signal cable, RS232 or RS485cable.
Do not connect the TV to the local video output port (VOUT).It may
result in video output circuit.
Always shut down the device properly. Please use the shutdown
‐ 131 ‐ function in the menu, or you can press the power button in the rear pane for at
least three seconds to shut down the device.
Otherwise it may result in HDD malfunction.
Please make sure the device is away from the direct sunlight or other
heating sources. Please keep the sound ventilation.
Please check and maintain the device regularly.
Appendix A HDD Capacity Calculation
Calculate total capacity needed by each DVR according to video recording
(video recording type and video file storage time).
Step 1: According to Formula (1) to calculate storage capacity q i that is the
capacity of each channel needed for each hour, unit Mbyte.:
In the formula: d i means the bit rate, unit Kbit/s
Step 2: After video time requirement is confirmed, according to Formula (2) to
calculate the storage capacity mi , which is storage of each channel needed
unit Mbyte.
In the formula:
hi means the recording time for each day (hour)
Di means number of days for which the video shall be kept
Step 3: According to Formula (3) to calculate total capacity (accumulation) qT
that is needed for all channels in the DVR during scheduled video recording.
In the formula: c means total number of channels in one DVR
Step 4: According to Formula (4) to calculate total capacity (accumulation) qT
that is needed for all channels in DVR during alarm video recording
(including motion detection).
In the formula:a% means alarm occurrence rate
‐ 132 ‐ Appendix B Compatible Backup Device List
Compatible USB drive list
NOTE: Please upgrade the DVR firmware to latest version to ensure the
accuracy of the table below. If you use the USB drive, please confirm the
format FAT or FAT32.
Manufacturer
Sandisk
Model
Cruzer Micro
Capacity
512M
Sandisk
Cruzer Micro
1G
Sandisk
Cruzer Micro
2G
Sandisk
Cruzer Freedom
256M
Sandisk
Cruzer Freedom
512M
Sandisk
Cruzer Freedom
1G
Sandisk
Cruzer Freedom
2G
Kingston
DataTravelerⅡ
1G
Kingston
DataTravelerⅡ
2G
Kingston
DataTraveler
1G
Kingston
DataTraveler
2G
Maxell
USB Flash Stick
128M
Maxell
USB Flash Stick
256M
Maxell
USB Flash Stick
512M
Maxell
USB Flash Stick
1G
Maxell
USB Flash Stick
2G
Kingax
Super Stick
128M
Kingax
Super Stick
256M
Kingax
Super Stick
512M
Kingax
Super Stick
1G
Kingax
Super Stick
2G
Netac
U210
128M
Netac
U210
256M
‐ 133 ‐ Netac
U210
512M
Netac
U210
1G
Netac
U210
2G
Netac
U208
4G
Teclast
Ti Cool
128M
Teclast
Ti Cool
256M
Teclast
Ti Cool
512M
Teclast
Ti Cool
1G
SanDisk SanDisk SanDisk
SanDisk
cruzer mirco cruzer mirco Ti
Cool Hongjiao
2G 8G 2G
4G
Lexar
Kingston
Kingston
Kingston
Aigo
Sandisk
Kingston
Netac
Lexar
Data Traveler
Data Traveler
Data Traveler
L8315
250
Data Traveler Locker+
U228
256MB
1G
16GB
32GB
16GB
16GB
32GB
8GB
Compatible SD Card List
Brand
Standard
Capacity
Card type
Transcend
SDHC6
16GB
SD
Kingston
SDHC4
4GB
SD
Kingston
SD
2GB
SD
Kingston
SD
1GB
SD
Sandisk
SDHC2
8GB
Micro-SD
Sandisk
SD
1GB
Micro-SD
Compatible Portable HDD List
Please refer to the following sheet for compatible portable HDD brand.
Brand
YDStar
Netac
Model
YDstar HDD box
Netac
‐ 134 ‐ Capacity
40G
80G
Iomega
Iomega RPHD-CG" RNAJ50U287
250GB
WD Elements
WCAVY1205901
1.5TB
Newsmy
Liangjian
320GB
WD Elements
WDBAAR5000ABK-00
500GB
WD Elements
WDBAAU0015HBK-00
1.5TB
Seagate
FreeAgent Go(ST905003F)
500GB
Aigo
H8169
500GB
Compatible USB DVD Burner List
NOTE: Please upgrade the DVR firmware to latest version to ensure the
accuracy of the table below. And you can use the USB cable with the model
recommended to set USB burner.
Compatible SATA DVD Burner List
NOTE: Please upgrade the DVR firmware to latest version to ensure the
accuracy of the table below.
Brand
Model
Pioneer
DVR-215CHG
Panasonic
SW-9588-C
Sumsung
TS-H653
Sony
DRU-V200S
Sony
DRU-845S
Sumsung
TS-H653
Pioneer
DVR-217CHG
LG
GH22NS30
Compatible SATA HDD List
NOTE: Please upgrade the DVR firmware to latest version to ensure the
accuracy of the table below. And SATA HDD should be used for the DVR with
SATA port. Here we recommend HDD of 500G to 4Tcapacity.
Manufacturer
Series
Model
Capacity
Port Mode
Seagate
Seagate SV35.1
ST3250824SV
250G
SATA
Seagate
Seagate SV35.1
ST3500641SV
500G
SATA
Seagate
Seagate SV35.2
ST3250820SV
250G
SATA
Seagate
Seagate SV35.2
ST3320620SV
320G
SATA
‐ 135 ‐ Manufacturer
Series
Model
Capacity
Port Mode
Seagate
Seagate SV35.2
ST3500630SV
500G
SATA
Seagate
Seagate SV35.2
ST3750640SV
750G
SATA
Seagate
Seagate SV35.3
ST3250310SV
250G
SATA
Seagate
Seagate SV35.3
ST3500320SV
500G
SATA
Seagate
Seagate SV35.3
ST3750330SV
750G
SATA
Seagate
Seagate SV35.3
ST31000340SV
1T
SATA
Seagate
Seagate SV35.4
ST3320410SV
320G
SATA
Seagate
Seagate SV35.4
ST3250311SV
250G
SATA
Seagate
Seagate SV35.5
ST3500410SV
500G
SATA
Seagate
Seagate SV35.5
ST3500411SV
500G
SATA
Seagate
Seagate SV35.5
ST31000525SV
1T
SATA
Seagate
Seagate SV35.5
ST31000526SV
1T
SATA
Seagate
Seagate SV35.5
ST1000VX000
1T
SATA
Seagate
Seagate SV35.5
ST2000VX003
2T
SATA
Seagate
Seagate SV35.5
ST2000VX002
2T
SATA
Seagate
Seagate SV35.5
ST2000VX000
2T
SATA
Seagate
Seagate SV35.5
ST3000VX000
3T
SATA
Seagate
Seagate Pipeline HD
ST3320410CS
320G
SATA
Seagate
Seagate Pipeline HD
ST3320310CS
320G
SATA
Seagate
Seagate Pipeline HD
ST3500422CS
500G
SATA
Seagate
Seagate Pipeline HD
ST3500321CS
500G
SATA
Seagate
Seagate Pipeline HD2
ST3250412CS
250G
SATA
Seagate
Seagate Pipeline HD2
ST3320311CS
250G
SATA
Seagate
Seagate Pipeline HD2
ST3500414CS
500G
SATA
Seagate
Seagate Pipeline HD2
ST3500312CS
500G
SATA
Seagate
Seagate Pipeline HD2
ST31000424CS
1T
SATA
Seagate
Seagate Pipeline HD2
ST31000322CS
1T
SATA
Seagate
Seagate Pipeline HD2
ST1000VM002
1T
SATA
Seagate
Seagate Pipeline HD2
ST1500VM002
1T
SATA
Seagate
Seagate Pipeline HD2
ST2000VM002
2T
SATA
Seagate
Seagate Pipeline HD2
ST2000VM003
2T
SATA
Seagate
Seagate Constellation ES
ST3500514NS
500G
SATA
Seagate
Seagate Constellation ES
ST31000524NS
1T
SATA
Seagate
Seagate Constellation ES
ST32000644NS
2T
SATA
Seagate
Seagate Constellation ES
ST2000NM0011
2T
SATA
Seagate
Seagate Constellation ES
ST1000NM0011
1T
SATA
Seagate
Seagate Constellation ES
ST500NM0011
500G
SATA
Seagate
Seagate Constellation ES
ST2000NM0031
2T
SATA
Seagate
Seagate Constellation ES
ST1000NM0031
1T
SATA
‐ 136 ‐ Manufacturer
Series
Model
Capacity
Port Mode
Seagate
Seagate Constellation ES
ST500NM0031
500G
SATA
Seagate
Seagate Constellation ES
ST2000NM0051
2T
SATA
Seagate
Seagate Constellation ES
ST1000NM0051
1T
SATA
Seagate
Seagate Constellation ES
ST500NM0051
500G
SATA
Seagate
Seagate Constellation ES.2
ST33000650NS
3T
SATA
Seagate
Seagate Constellation ES.2
ST32000645NS
2T
SATA
Seagate
Seagate Constellation ES.2
ST33000651NS
3T
SATA
Seagate
Seagate Constellation ES.2
ST32000646NS
2T
SATA
Seagate
Seagate Constellation ES.2
ST33000652NS
3T
SATA
Seagate
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Seagate Constellation ES.2
ST32000647NS
2T
SATA
Cariar SE
WD3200JD
320G
SATA
Cariar SE
WD3000JD
300G
SATA
Cariar SE
WD2500JS
250G
SATA
Cariar SE16
WD7500KS
750G
SATA
Cariar SE16
WD5000KS
500G
SATA
Cariar SE16
WD4000KD
400G
SATA
Cariar SE16
WD3200KS
320G
SATA
Cariar SE16
WD2500KS
250G
SATA
WD Caviar SE16
WD2500YS-01SHB0
250G
SATA
WD Caviar RE16
WD3200YS-01PGB0
320G
SATA
WD Caviar RE2
WD5000YS-01MPB0
500G
SATA
500G
SATA
320G
SATA
500G
SATA
500G
SATA
750G
SATA
WD AV—AVJS
WD AV—AVJS
WD AV—AVJS
WDAV-GP—AVCS
WDAV-GP—AVCS
WD2500AVJS-63WD
A0
WD3200AVJS-63WD
A0
WD5000AVJS-63YJA
0
WD5000AVCS-63H1
B1
WD7500AVCS-63ZLB
0
WDAV-GP—AVCS
WD3200AVCS
320G
SATA
WDAV-GP—AVCS
WD2500AVCS
250G
SATA
WDAV-GP—EVCS
WD10EVCS-63ZLB0
1T
SATA
WDAV-GP—EVCS
WD20EVCS-63ZLB0
2T
SATA
‐ 137 ‐ Manufacturer
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Westem
Digital
Samsung
Series
Model
WD3200AVVS-63L2B
0
WD5000AVVS-63ZW
B0
WD7500AVVS-63E1B
1
WD7500AVVS-63E1B
1
Capacity
Port Mode
320G
SATA
500G
SATA
750G
SATA
750G
SATA
WDAV-GP—EVVS
WD10EVVS-63E1B1
1T
SATA
WDAV-GP—EVDS
WD10EVDS-63N5B1
1T
SATA
WDAV-GP—EVDS
WD15EVDS-63V9B0
1.5T
SATA
WDAV-GP—EVDS
WD20EVDS-63T3B0
2T
SATA
WDAV-GP—AVDS
WD5000AVDS-63U7
B0
500G
SATA
WD AV-GP
WD30EURS
3T
SATA
WD AV-GP
WD25EURS
2.5T
SATA
WD AV-GP
WD20EURS
2T
SATA
WD AV-GP
WD15EURS
1.5T
SATA
WD AV-GP
WD10EURS
1T
SATA
WD AV-GP
WD10EURX
1T
SATA
WD AV-GP
WD7500AURS
750G
SATA
WD AV-GP
WD7500AVDS
500G
SATA
WD AV-GP
WD500AVDS
500G
SATA
WD AV-GP
WD10EUCX
1T
SATA
Samsung
Samsung—HA
HA500LJ/CE
500G
SATA
Samsung—HA
HA751LJ
750G
SATA
Samsung
Samsung—HA
HA101UJ/CE
1T
SATA
SATA
WDAV-GP—AVVS
WDAV-GP—AVVS
WDAV-GP—AVVS
WDAV-GP—AVVS
Samsung
Samsung——HD
HD502HI/CEC
500G
Samsung
Samsung——HD
HD103SI/CEC
1T
SATA
Samsung
Samsung—HD
HD154UI/CE
1.5T
SATA
Hitach
Hitach CinemaStar™ 5K500
HCP725050GLA380
500G
SATA
Hitach
Hitach CinemaStar™
7K1000.B
HCT721050SLA360
500G
SATA
Hitach
Hitach CinemaStar™
7K1000.B
HCT721075SLA360
750G
SATA
‐ 138 ‐ Manufacturer
Series
Model
Capacity
Port Mode
Hitach
Hitach CinemaStar™
7K1000.B
HCT721010SLA360
1T
SATA
Maxtor
DiamondMax 20
STM3320820AS
320G
SATA
Maxtor
DiamondMax 20
STM3250820AS
250G
SATA
Appendix C Compatible CD/DVD Device List
Manufacturer
Model
Port Type
Type
Sony
DRX-S50U
USB
DVD-RW
Sony
DRX-S70U
USB
DVD-RW
Sony
AW-G170S
SATA
DVD-RW
Samsung
TS-H653A
SATA
DVD-RW
Panasonic
SW-9588-C
SATA
DVD-RW
Sony
DRX-S50U
USB
DVD-RW
BenQ
5232WI
USB
DVD-RW
Appendix D Compatible Displayer List
Brand
BENQ(LCD)
DELL(LCD)
Model
ET-0007-TA
E178FPc
Dimension (Unit: inch)
19-inch (wide screen)
17-inch
BENQ(LCD)
Q7T4
17-inch
BENQ(LCD)
LENOVO(LCD)
Q7T3
LXB-L17C
17-inch
17-inch
SANGSUNG(LCD)
HFNOVO (CRT)
HFNOVO (CRT)
HFNOVO (CRT)
225BW
LXB-FD17069HB
LXB-HF769A
LX-GJ556D
22-inch (wide screen)
17-inch
17-inch
17-inch
‐ 139 ‐ Samsung(LCD)
2494HS
24-inch
Samsung(LCD)
P2350
23-inch
Samsung(LCD)
Samsung(LCD)
Samsung(LCD)
Samsung(LCD)
P2250
P2370G
2043
2243EW
22-inch
23-inch
20-inch
22-inch
Samsung(LCD)
SMT-1922P
19-inch
Samsung(LCD)
Samsung(LCD)
T190
T240
19-inch
24-inch
LG(LCD)
LG(LCD)
LG(LCD)
BENQ(LCD)
W1942SP
W2243S
W2343T
G900HD
19-inch
22-inch
23-inch
18.5-inch
BENQ(LCD)
PHILIPS(LCD)
PHILIPS(LCD)
PHILIPS(LCD)
PHILIPS(LCD)
G2220HD
230E
220CW9
220BW9
220EW9
22-inch
23-inch
23-inch
24-inch
25-inch
Appendix E Compatible Switcher List
Brand
Model
Network working Mode
D-LinK
D-LinK
Ruijie
DES-1016D
DES-1008D
RG-S1926S
10/100M self-adaptive
10/100M self-adaptive
There are five network modes:
1、AUTO
2、HALF-10M
3、FULL-10M
4、HALF-100M
5、FULL-100M
H3C
H3C-S1024
10/100M self-adaptive
‐ 140 ‐ TP-LINK
TP-LINK
TL-SF1016
TL-SF1008+
10/100M self-adaptive
10/100M self-adaptive
Appendix F Compatible Wireless Mouse List
Brand
Model
V80
3500
M215
Tianyao G7-630
Rapoo
Logitech
Shuangfeiyan
Appendix G Specifications
Parameter
System
8CH
High-performance industrial embedded micro
controller
OS
Embedded LINUX
System
Resources
Multiplex operations: Multiple-channel record,
multiple-channel playback and network operation
simultaneously
Interface
User-friendly graphical user interface
Input Devices
Input Method
Shortcut
Function
Compression
Standard
4CH
Main Processor
Video
Compression
USB mouse
Arabic number, English character, donation and
extension Chinese (optional)
Copy/paste operation, USB mouse right-key shortcut
menu, double click USB mouse to switch screen.
H.264
‐ 141 ‐ Parameter
Audio
Compression
Video Input
Video
Output
4CH
8CH
G711A、G711U、PCM
4-CH composite video
input
8-CH composite video
input
1-ch VGA output.
1-ch HDMI output.
Support VGA/HDMI video output at the same time.
Video
Standard
Support PAL/NTSC.
Record
Speed
Real-time Mode: PAL 1f/s to 25f/s per channel and
NTSC 1f/s to 30f/s
per channel
Video
Partition
Video monitor
Monitor
Touring
Resolution
(PAL/NTSC
1/4 windows(Optional)
1/4/8/9 windows
Support monitor tour functions such as motion detection,
and
schedule
auto control.
PAL/NTSC
Real-time monitor:
1080P/720P
PAL/NTSC
Image
Quality
Privacy
Video monitor
mask
Image
Information
Channel
Lock
Audio
6-level image quality (Adjustable)
Support one privacy mask of user-defined size in full
screen.
Support max 4 zones.
Channel information, time information and privacy mask
zone.
Cover secret channel with black screen though system
is encoding
normally.
Channel
Information
Channel name, recording status, screen lock status,
video loss status and motion detection status are shown
on the bottom left of display screen.
Color
Configuration
Hue, brightness, contrast, saturation and gain setup for
each channel.
Audio
1CH 200~2000mV 10KΩ(RCA)
Audio Input
1-ch 200-2000mv 10KΩ(RCA)
Audio
Output
1-ch audio output 200-3000mv 5KΩ(RCA)
‐ 142 ‐ Parameter
Hard disk
8CH
Hard disk
2 built-in SATA port. Support 1 HDD.
One HDD
Space
4T
Hard Disk
Occupation
Audio:PCM 28.8MByte/h
Video:56-900MByte/h
Recording
Mode
Manual recording, motion detection recording, schedule
recording
And alarm recording.
Priority: Manual recording> alarm recording>motion
detection
recording>schedule recording.
Storage
Mode
Recording
Length
Playback
Repeat
Way
Record and
playback
4CH
Record
Search
Playback
Mode
Various File
Switch
Ways
Support channel record quota setup
1 to 120 minutes single record duration (Default setup is
60 minutes)
When hard disk is full, system can overwrite previous
video file.
Various search engines such as time, type and channel.
Various fast play, slow play speeds, manual frame by
frame playback and reverse play mode.
Can switch to file on other channel of the same time. (If
there is a file)
Support file continuous play, when a file is end system
auto plays next file in the current channel
Playback
Way
Multichannel
Playback
Window
Zoom
Support mark playback
Partial
Enlargement
When in one-window full-screen playback mode, you
can select any zone to activate partial enlargement
function.
Multichannel
Playback
Window Zoom
HDD backup
Backup
function
Backup
mode
Support peripheral USB backup device. (Flash disk,
portable disk and etc.)
Support network download and save
Network
function
Network
control
View monitor channel remotely.
DVR configuration through client-end and web browser
‐ 143 ‐ Parameter
4CH
8CH
Upgrade via client or browser to realize remote
maintenance.
View alarm information such as motion detection and
video loss via client.
Support network PTZ lens control
File download backup and playback
Multiple devices share information via corresponding
software such as professional surveillance software
(PSS)
Duplex transparent COM
Network alarm input and output
Zero-channel encoding.
Bidirectional audio.
Motion
Detection
and
Alarm
Motion
Detection
Video Loss
Interface
System
Information
USB
Interface
Network
connection
Alarm can activate screen message prompt.
2 USB 2.0 port.
RJ45 10M/100M self-adaptable Ethernet port
RS485
PTZ control port.
Support various PTZ control protocols
RS232
N/A
Hard Disk
Information
Data
Stream
Statistics
Log
statistics
Version
On-line user
User
Management
Zone setup: support 396((PAL 22×18, NTSC 22×15))
detection zones. Various sensitivity levels.
Alarm can activate record or external alarm or screen
message prompt
User
Management
Display HDD current status
Data stream statistics for each channel (in wave mode)
Backup to 1024 log files.
Support various search engines such as time and type.
Display version information: channel amount, system
version and
Release data
Display current on-line user
Multi-lever user management; various management
modes Integrated management for local user, serial port
user and network user. Configurable user power.
Support user /group and its corresponding rights
modification. No limit to the user or group amount.
‐ 144 ‐ Parameter
4CH
8CH
Password modification Administrator can modify other
user’s password.
Account lock strategy
Five times login failure in thirty minutes may result in
account lock.
Password
Authentication
Upgrade
Web browser, client-end and update tool.
Password login protection to guarantee safety
User-friendly interface when login. Provide the following
options:
Logout
/shutdown/ restart.
Right authentication when shut down to make sure only
those proper people can turn off DVR
Login, Logout and Shutdown
Power
General
Parameter
DC 12V
Power
Consumption
Working
Temperature
Working
Humidity
Air
Pressure
≤15W (With adapter, exclude HDD)
-10℃~+55℃
10%~90%
86kpa~106kpa
Appendix H Toxic or Hazardous Materials or
Elements
Component Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
Sheet Metal(Case)
○
○
○
○
○
○
Plastic Parts (Panel)
○
○
○
○
○
○
Circuit Board
○
○
○
○
○
○
Circuit Board
○
○
○
○
○
○
Wire and Cable/Ac
Adapter
○
○
○
○
○
○
○
○
○
○
○
○
Packing Material
‐ 145 ‐ Accessories
○
○
○
○
○
○
Note
O: Indicates that the concentration of the hazardous substance in all
homogeneous materials in the parts is below the relevant threshold of
the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least
one of all homogeneous materials in the parts is above the relevant
threshold of the SJ/T11363-2006 standard. During the environmental
-friendly use period (EFUP) period, the toxic or hazardous substance or
elements contained in products will not leak or mutate so that the use of
these (substances or elements) will not result in any severe environmental
pollution, any bodily injury or damage to any assets. The consumer is not
authorized to process such kind of substances or elements, please return
to the corresponding local authorities to process according to your local
government statutes
Note:
This manual is for reference only. Slight difference may be found in the user
interface.
● All the designs and software here are subject to change without prior
written notice.
● All trademarks and registered trademarks mentioned are the properties of
their respective owners.
● If there is any uncertainty or controversy, please refer to the final
explanation of us.
● Please visit our website or contact your local retailer for more information.
‐ 146 ‐