*
5
1
0
0
0
1
7
6
0
2
-
0
1
*
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2; p. 3).
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read
in its entirety. The manual should be saved and kept on hand as a convenient reference.
About
WARNING and
CAUTION Notices
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
About the Symbols
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
ALWAYS OBSERVE THE FOLLOWING
WARNING
• Do not open or perform any internal modifications on the
unit.
• Do not attempt to repair the unit, or replace parts within
it (except when this manual provides specific instructions
directing you to do so). Refer all servicing to your retailer,
the nearest Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
• Never install the unit in any of the following locations.
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating duct,
on top of heat-generating equipment); or are
WARNING
• Never allow foreign objects (e.g., flammable objects, coins,
wires) or liquids (e.g., water or juice) to enter this product.
Doing so may cause short circuits, faulty operation, or other
malfunctions.
• In households with small children, an adult should provide
supervision until the child is capable of following all the
rules essential for the safe operation of the unit.
• Protect the unit from strong impact.
(Do not drop it!)
• Damp (e.g., baths, washrooms, on wet floors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness.
• This unit should be used only with a stand (MDS series) that
is recommended by Roland.
• When using the unit with a stand (MDS series)
recommended by Roland, the stand (MDS series) must be
carefully placed so it is level and sure to remain stable. If
not using a stand (MDS series), you still need to make sure
that any location you choose for placing the unit provides
a level surface that will properly support the unit, and keep
it from wobbling.
2
CAUTION
• Try to prevent cords and cables from becoming entangled.
Also, all cords and cables should be placed so they are out
of the reach of children.
• Never climb on top of, nor place heavy objects on the unit.
• Should you remove the stopper bolt, keep them in a safe
place out of children’s reach, so there is no chance of them
being swallowed accidentally.
IMPORTANT NOTES
Placement
• Do not expose the unit to direct sunlight, place it near devices that
radiate heat, leave it inside an enclosed vehicle, or otherwise subject
it to temperature extremes. Excessive heat can deform or discolor the
unit.
• When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation) may
form inside the unit. Damage or malfunction may result if you attempt
to use the unit in this condition. Therefore, before using the unit, you
must allow it to stand for several hours, until the condensation has
completely evaporated.
• Do not allow rubber, vinyl, or similar materials to remain on this unit for
long periods of time. Such objects can discolor or otherwise harmfully
affect the finish.
Maintenance
• For everyday cleaning wipe the unit with a soft, dry cloth or one that
has been slightly dampened with water. To remove stubborn dirt, use a
cloth impregnated with a mild, non-abrasive detergent. Afterwards, be
sure to wipe the unit thoroughly with a soft, dry cloth.
• Never use benzine, thinners, alcohol or solvents of any kind, to avoid
the possibility of discoloration and/or deformation.
Additional Precautions
• Use a reasonable amount of care when using the output jacks. Rough
handling can lead to malfunctions.
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing shorts,
or damage to the cable’s internal elements.
• To avoid disturbing your neighbors, try to keep the unit’s volume at
reasonable levels. You may prefer to use headphones, so you do not
need to be concerned about those around you.
• This instrument is designed to minimize the extraneous sounds
produced when it’s played. However, since sound vibrations can be
transmitted through floors and walls to a greater degree than expected,
take care not to allow these sounds to become a nuisance to neighbors,
especially when using headphones.
• When you need to transport the unit, package it in the box (including
padding) that it came in, if possible. Otherwise, you will need to use
equivalent packaging materials.
• The rubber portion of the striking surface is treated with a preservative
to maintain its performance. With the passage of time, this preservative
may appear on the surface as a white stain, or reveal how the
pads were struck during product testing. This does not affect the
performance or functionality of the product, and you may continue
using it with confidence.
• Continuous playing may cause dis-coloration of the pad, but this will
not affect the Pad’s function.
• All product names mentioned in this document are trademarks or
registered trademarks of their respective owners.
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland,V-Drums, and V-CYMBALS are registered trademarks of Roland Corporation in the United States and/or other countries.
3
Getting Started
What’s in the Package
CY-12C
BOW/EDGE
OUTPUT jack
CY-13R (Ride)
• CY-13R Cymbal pad
• Wing nut
• Felt washer
Bow
Edge
• Stopper
* The CY-12C has no BOW/BELL OUTPUT jack.
• Connection cable (stereo) x 2
Diameter: 12 inches
• Cable tie
Main Specifications
• Owner´s manual (this document)
CY-12C (Crash)
CY-13R (Ride)
• CY-12C Cymbal pad
Size
13 inches
• Wing nut
Trigger
3 (Bow/Bell/Edge)
• Felt washer
Connectors
BELL OUTPUT jack,
BOW/EDGE OUTPUT jack
• Stopper
Dimensions
• Connection cable (stereo)
331 (W) x 331 (D) x 48 (H) mm
13-1/16 (W) x 13-1/16 (D) x 1-15/16 (H) inches
Weight
1.1 kg / 2 lbs 7 oz
Accessories
Owner’s manual, Wing nut, Felt washer, Stopper,
Connection cable (stereo) x 2, Cable tie
Options
Cymbal mount (MDY series)
Cymbal parts set (CYM-10)
• Cable tie
• Owner´s manual (this document)
Definitions & Names of Parts
CY-13R
BOW/EDGE
OUTPUT jack
Bell
Bow
Edge
BELL
OUTPUT jack
Diameter: 13 inches
* The CY-13R is not capable of detecting the striking
position.
If you’re using a Roland percussion sound module that is
capable of detecting the striking position, you’ll need to
set the ride’s Position Ctrl to OFF.
For details on how to make the setting, refer to the
owner’s manual that came with your percussion sound
module.
4
CY-12C (Crash)
Size
12 inches
Trigger
2 (Bow/Edge)
Connectors
BOW/EDGE OUTPUT jack
Dimensions
305 (W) x 305 (D) x 45 (H) mm
12-1/16 (W) x 12-1/16 (D) x 1-13/16 (H) inches
Weight
940 g / 2 lbs 2 oz
Accessories
Owner’s manual, Wing nut, Felt washer, Stopper,
Connection cable (stereo), Cable tie
Options
Cymbal mount (MDY series)
Cymbal parts set (CYM-10)
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to
change without prior notice.
Making the Settings
Mounting on the Stand
1. Use a commercially available drum key to tighten
the stopper bolt.
The stopper keeps the V-Cymbal from turning, preventing
the tangling of cables on the stand.
Stopper
Bolt
Attach the stopper
so that the bolt is on
the right-hand side,
from the performer’s
perspective.
Tighten the bolt
with a commercially
available drum key
Connecting to a Percussion
Sound Module
* To prevent malfunction and/or damage to speakers or
other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
* Use the supplied connection cables (stereo) to make the
connections. If monaural cables are used, edge shots,
bell shots, and choke play cannot be supported.
Connect the L-shaped plug of the included cable to the
CY-13R/12C.
The CY-12C has no BELL OUTPUT jack. Make the
connection to the BOW/EDGE OUTPUT jack.
2. Attach the V-Cymbal, while positioning it so the
Roland logo is located on the side opposite the
performer.
Position the Roland logo
on the opposite side of
the playing area
Wing nut
CY-13R (Ride)
CY-12C (Crash)
BELL
OUTPUT jack
BOW/EDGE
OUTPUT jack
BOW/EDGE
OUTPUT jack
RD cable (TD-9, TD-4)
CR1, 2 cable (TD-9, TD-4)
To EDGE jack
(TD-20X, TD-20, TD-12)
To CRASH 1, 2 jack
(TD-20X, TD-20, TD-12)
RDB cable (TD-9)
Felt washer
3. Tighten the included felt washer and the wing nut
to obtain the desired movement.
CR2 cable (TD-4) *1
To RIDE jack (TD-20X, TD-20, TD-12)
*1 Set the Crash 2 Usage parameter to “RIDE BELL.”
* Use the included felt washer and wing nut.
* Double sounding may occur if the wing nut is loose.
4. Secure the cables in place with the cable tie, and
leave some slack in the cables to ensure they are
not pulled by the movement of the V-Cymbal
pads.
Be sure to make this
small plastic hook
visible from you.
Wind a cable tie around
a cable.
Leave some
slack in the
cable
Secure the cable in place with
the cable tie
Wind a cable tie around
the pipe and tighten it in
order to not to slip.
Insert the
small plastic
hook to a hole
to secure the cable
to the cymbal arm.
About three-way triggering (CY-13R only)
The CY-13R can take advantage of your percussion
sound module’s three-way triggering functionality
to allow you to play bow, bell, and edge separately.
Connect the two outputs BOW/BELL and BOW/EDGE
to the percussion sound module at the same time.
For details on the connection method and settings,
refer to the owner’s manual for your percussion
sound module.
* If you won’t be using the three-way triggering
functionality, connect the BOW/EDGE OUTPUT
jack (not both) to your percussion sound module.
* Although you’ll be able to play using the bow and
bell sections when connected to the BELL OUTPUT
jack, you won't be able to use the choking
technique.
* Take care to ensure that the cables do not touch the
V-Cymbal pads and/ or the stand. A cable touching a
V-Cymbal pad or a stand may cause double sounding or
other incorrect operation.
5
Playing Methods
Bow Shot
Bell Shot (CY-13R Only)
This is the most common playing method, playing the
middle area of the cymbal.
It corresponds to the sound of the “head-side” of the
connected trigger input.
Edge Shot
This playing method involves striking the edge with the
shoulder of the stick.
When played as shown in the figure, the “rim-side” sound
of the connected input is triggered.
This playing method involves striking the bell.
On the CY-13R, when played as shown in the figure, the
“rim-side” sound of the connected input is triggered.
Strike the bell somewhat strongly with the shoulder of the
stick.
* Bell shots are possible when the connection is made to
the CY-13R’s BELL output.
* On the CY-12C, bell shots are not supported.
Choke Play
Choking (pinching) the cymbal’s edge with the hand
immediately after hitting the cymbal makes the sound
stop.
Edge sensor
Choke the location of the edge sensor shown in the figure.
If you choke an area where there is no sensor, the sound
does not stop.
Roland logo
* On the CY-13R, edge shots are possible when the
connection is made to the BOW/EDGE OUTPUT jack.
Edge sensor
* When ONLY using the BELL output of the CY-13R, the
choke function will not work.
6
Trigger Parameter Settings for the Percussion Sound Module
Playing Techniques Supported by Various Percussion Sound Modules
CY-13R, CY-12C
Bow/Edge Shot
Model name
CY-13R
Three Way Triggering
CY-13R, CY-12C
Choke Play
TD-20X, TD-20, TDW-20
3
3
3
TD-12
3
3
3
TD-9
3
3
3
TD-4
3
3
3
* For details, refer to the owner's manual for your percussion sound module.
Recommended Settings for the Trigger Parameters
These are the recommended trigger parameter settings when using the V-Cymbal with various models of sound module.
You may need to adjust the trigger parameters depending on how you’ve attached the V-Cymbal and the location at which
you’ve installed it.
* In order to use three-way triggering with the CY-13R, you must make settings on your percussion sound module to use its
three-way triggering functionality. For details on the procedure, refer to the owner’s manual for your percussion sound
module.
TD-20X, TD-20, TDW-20, TD-12
TD-4
Recommended trigger type setting
Recommended pad type setting
Trig Type
CY12RC
Model name
Value
Retrig Cancel
8
CY-13R
CY-13R
Rim Gain
0.8
CY-12C
CY-12C
Inputs that allows three-way triggering
TD-20X, TD-20, TDW-20
10 RIDE, 11 EDGE
TD-12
9 RIDE, 10 EDGE
TD-9
Recommended trigger type setting
Model name
Value
CY-13R
CY13R
CY-12C
CY12C
If “CY-12C” and “CY-13R” are not shown as a Pad Type value,
make settings as follows.
Trigger Parameter
CY-13R
CY-12C
Pad Type
CY-12R/C
CY-12R/C
Rim Gain
0.9
0.8
Connection cable that enables the use of threeway triggering
Connection cable
RD plug, CR2 plug
If “CY12C” and “CY13R” are not shown as a Trig Type value,
make settings as follows.
Trig Type
CY12RC
Rim Gain
0.8
Connection cable that enables the use of threeway triggering
Connection cable
RD plug, RDB plug
7
For EU Countries
For China
For C.A. US (Proposition 65)
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
Information
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar Al Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (022)-417-1828
REUNION
MARCEL FO-YAM Sarl
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
T.O.M.S. Sound & Music (Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
TEL: (011) 417 3400
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd. (BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011, CHINA
TEL: (010) 6426-5050
HONG KONG
Tom Lee Music
11/F Silvercord Tower 1
30 Canton Rd
Tsimshatsui, Kowloon,
HONG KONG
TEL: 825-2737-7688
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
INDIA
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra Intirama
Jl. Cideng Timur No. 15J-15O
Jakarta Pusat,
INDONESIA
TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
VIET NAM
VIET THUONG CORPORATION
386 CACH MANG THANG TAM ST.
DIST.3, HO CHI MINH CITY,
VIET NAM
TEL: (08) 9316540
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
CURACAO
URUGUAY
POLAND
JORDAN
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL: (305) 5926866
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
ROLAND POLSKA SP. Z O.O.
ul. Kty Grodziskie 16B
03-289 Warszawa, POLAND
TEL: (022) 678 9512
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192, JORDAN
TEL: (06) 5692696
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
TAIWAN
ROLAND TAIWAN ENTERPRISE
CO., LTD.
9F-5, No. 112 Chung Shan
North Road Sec. 2 Taipei 104,
TAIWAN R.O.C.
TEL: (02) 2561 3339
THAILAND
Theera Music Co. , Ltd.
100-108 Soi Verng Nakornkasem,
New Road,Sumpantawong,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
OCEANIA
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099,
AUSTRALIA
For Australia
TEL: (02) 9982 8266
For New Zealand
TEL: (09) 3098 715
CENTRAL/LATIN
AMERICA
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
DOMINICAN REPUBLIC
TEL: (809) 683 0305
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - ECUADOR
TEL: (593-4) 2302364
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final Alameda
Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala,
GUATEMALA
TEL: (502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, HONDURAS
TEL: (504) 553-2029
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin,
MARTINIQUE F.W.I.
TEL: 596 596 426860
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
MARTINIQUE F.W.I.
TEL: 596 596 715222
MEXICO
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires, ARGENTINA
TEL: (011) 4508-2700
BARBADOS
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, BARBADOS
TEL: (246) 430-1100
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 211
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, COLOMBIA
TEL: (574) 3812529
COSTA RICA
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.,
MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, NICARAGUA
TEL: (505) 277-2557
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De Instrumentos
Musicales
J.E. Olear y ESQ. Manduvira
Asuncion, PARAGUAY
TEL: (595) 21 492147
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - PERU
TEL: (511) 4461388
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria TRINIDAD W.I.
TEL: (868) 638 6385
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar import
#7 zona Industrial de Turumo
Caracas, VENEZUELA
TEL: (212) 244-1122
PORTUGAL
Roland Iberia, S.L.
Branch Office Porto
Edifício Tower Plaza
Rotunda Eng. Edgar Cardoso
23, 9ºG
4400-676 Vila Nova de Gaia,
PORTUGAL
TEL: (+351) 22 608 00 60
ROMANIA
EUROPE
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
CROATIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb, CROATIA
TEL: (1) 466 8493
CZECH REP.
CZECH REPUBLIC DISTRIBUTOR
s.r.o
Voctárova 247/16
180 00 Praha 8, CZECH REP.
TEL: (2) 830 20270
DENMARK
Roland Scandinavia A/S
Skagerrakvej 7 Postbox 880
DK-2100 Copenhagen,
DENMARK
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Vanha Nurmijarventie 62
01670 Vantaa, FINLAND
TEL: (0) 9 68 24 020
GERMANY/AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
GREECE/CYPRUS
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
2045 Torokbalint, FSD Park,
building 3., HUNGARY
TEL: (23) 511011
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12,
Republic of IRELAND
TEL: (01) 4294444
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
NORWAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo,
NORWAY
TEL: 2273 0074
KUWAIT
EASA HUSAIN AL-YOUSIFI &
SONS CO.
Al-Yousifi Service Center
P.O.Box 126 (Safat) 13002,
KUWAIT
TEL: 00 965 802929
LEBANON
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609
Chahine S.A.L.
George Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
RUSSIA
OMAN
Roland Music LLC
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (495) 981-4967
SERBIA
Music AP Ltd.
Sutjeska br. 5 XS - 24413 Palic,
SERBIA
TEL: (024) 539 395
SLOVAKIA
DAN Acoustic s.r.o.
Povazská 18.
SK - 940 01 Nové Zámky,
SLOVAKIA
TEL: (035) 6424 330
SPAIN
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona, SPAIN
TEL: 93 493 91 00
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Mårbackagatan 31, 4 tr.
SE-123 43 Farsta, SWEDEN
TEL: (0) 8 683 04 30
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen, SWITZERLAND
TEL: (061) 975-9987
UKRAINE
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo, UKRAINE
TEL: (03131) 414-40
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
QATAR
AL-EMADI TRADING &
CONTRACTING CO.
P.O. Box 62, Doha, QATAR
TEL: 4423-554
SAUDI ARABIA
aDawliah Universal Electronics
APL
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952,
SAUDI ARABIA
TEL: (03) 8643601
SYRIA
Technical Light & Sound Center
PO Box 13520 Bldg No.49
Khaled Abn Alwalid St.
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.33
Beyoglu, Istanbul, TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
TEL: (04) 3360715
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA SA7
9FJ, UNITED KINGDOM
TEL: (01792) 702701
MIDDLE EAST
BAHRAIN
Moon Stores
No.1231&1249 Rumaytha
Building Road 3931,
Manama 339, BAHRAIN
TEL: 17 813 942
IRAN
MOCO INC.
NO.16 End of Nike St. Shariaty
Ave, Roberouye Cerah Mirdamad
Teheran, IRAN
TEL: (021)-2288-2998
ISRAEL
NORTH AMERICA
CANADA
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way Richmond B.
C., V6V 2M4, CANADA
TEL: (604) 270 6626
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6,
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
As of Apr. 1, 2010 (ROLAND)