Water Heater
Feel the drive
e1
Thermo Top E Parking Heater 00 0003
Installation documentation
Ford Focus / Focus C-MAX / Focus CC
Petrol
from Model Year 2004
For left-hand drive vehicles only
WARNING!
Hazard warning:
Incorrect installation or repair of Webasto heating systems may cause a fire or result in the
emission of carbon monoxide, which can be fatal. Serious or fatal injuries can be caused as
a result.
Specialist company training, technical documentation, specialised tools and equipment are
required to install and repair Webasto heating and cooling systems.
Only original Webasto parts must be used. For this, also see the catalog of air and water heater accessories from Webasto.
NEVER attempt to install or repair Webasto heating or cooling systems if you have not
successfully completed the company training and thereby acquired the required technical skills, or if you do not have access to the required technical documentation, tools
and equipment needed to carry out correct installation and repairs.
ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
The initial startup is to be executed with the Webasto Thermo Test Diagnosis.
Webasto does not accept any liability for defects and damage that are attributable to installation by untrained staff.
Ident. No.: 1303854F_EN
Fee Euro 10.00
© Webasto AG
Ford Focus / Focus C-MAX / Focus CC
Table of contents
Validity
2
Heater/installation kit
3
Foreword
3
General instructions
3
Special tools
3
Preliminary work
5
Heater installation location
5
Preparing electrical system
6
Electrical system of Focus
7
Electrical system for Focus/Focus CC from 2008 8
Electrical system of C-Max
9
Fan control without automatic A/C
10
Automatic A/C fan control
11
Additionally for automatic A/C from 01/06
13
Remote option (Telestart)
15
Preparing installation location
Premounting heater
Fastening for underride protection
Installing heater
Coolant circuit
Fuel
Mounting underride protection
Final Work
Operating instructions for end customer
16
18
19
19
21
23
26
27
28
Validity
Manufacturer
Ford
Ford
Ford
Ford
Model
Focus
Focus
Focus C-MAX
Focus CC
Type
DA3
DB3
DM2
DB3
EG-BE-No. / ABE
e13*2001 / 116*0144
e13*2001 / 116*0144
e13*2001 / 116*0109
e13*2001 / 116*0157
Engine type
Engine model
Output in kW
Displacement in cm³
ASDA
ASDB
HWDB
HXDA
Q7DA
QQDB
AODA
AODB
Petrol
Petrol
Petrol
Petrol
Petrol/Flexifuel
Petrol
Petrol
Petrol
59
59
74
85
92
92
107
107
1388
1388
1596
1596
1798
1798
1999
1999
Vehicle and engine types, equipment variants and national specifications not listed in this installation
documentation have not been tested. However, installation according to this installation documentation
may be possible.
The installation location of a digital timer and summer/winter switch should be confirmed with the end
customer before installation.
2
Ford Focus / Focus C-MAX / Focus CC
Heater/installation kit
Quantity
1
1
Designation
Ford Delivery Scope for Focus/ Focus C-MAX Petrol without heater control
Original fuel standpipe with Ford Finis Code
Order No.:
1303858C
1233999
Additionally required optional heater control:
Quantity
1
1
Designation
Digital timer
Telestart
Order No.:
See price list
See price list
Additionally required with automatic air-conditioning up to 2005 Model Year:
Quantity
1
Designation
Kit for automatic air-conditioning on Ford Focus/Focus C-MAX
Order No.:
9012822A
Additionally required with automatic air-conditioning from 2006 Model Year:
Quantity
1
Designation
Kit for automatic air-conditioning on Ford Focus/Focus C-MAX
Order No.:
9015495A
Foreword
This installation documentation applies to Ford Focus / Focus C-MAX / Focus CC vehicles with Petrol
engine - for validity, see page 2 - from model year 2004 and later, assuming technical modifications to
the vehicle do not affect installation, any liability claims excluded. Depending on the vehicle version
and equipment, modifications may be necessary during installation with respect to this installation documentation.
However, where this is the case, the stipulations in this "installation documentation" the "operating instructions" and "installation instructions" of the Thermo Top E should be observed.
The corresponding rules of technology and any information from the vehicle manufacturer should be
observed during the installation work.
General instructions
Installation should be carried out according to the general, standard rules of technology. Unless specified otherwise, fasten hoses, lines and wiring harnesses to original vehicle lines and wiring harnesses
using cable ties.
Sharp edges must be provided with rub protection (cut-open fuel hose)!
Spray unfinished body areas, e.g. drilled holes, with anti-corrosion wax (Tectyl 100K, Order No. 111329).
When installing an IPCU, the corresponding settings must be checked or adjusted before installation.
Special tools
-
Torque wrench for 2.0 - 10 Nm
Hose clamping pliers
Metric thread-setter kit for M6 aluminum rivet nut
Metric thread-setter kit for M10 steel rivet nut (e.g. Würth Order No. 0964948900)
3
Ford Focus / Focus C-MAX / Focus CC
Explanatory notes on document
To provide you with a quick overview of the individual working steps, you will find an identification mark
on the outside top right corner of the page in question.
Mechanical system
Electrical system
Coolant circuit
Fuel
Exhaust gas
Combustion air
Special features are highlighted using the following symbols:
Specific risk of injury or fatal accidents.
Specific risk of damage to components.
Specific risk of fire or explosion.
i
Reference to general installation instructions of Webasto components or to the manufacturer's vehicle-specific
documents.
Reference to a special technical feature.
The arrow in the vehicle icon indicates the position on
the vehicle and the viewing angle.
4
Ford Focus / Focus C-MAX / Focus CC
Preliminary work
Warning!
- Open the fuel tank cap and vent the fuel tank.
- Close the fuel tank cap again.
- Disconnect the battery earth connection.
- Depressurise the cooling system.
- Copy the factory number from the original type label to the duplicate type label.
- Remove years that do not apply from the duplicate label.
- Attach the duplicate label (type label) in the appropriate place.
- Remove the engine cover (if present).
- C-MAX only: remove the coolant reservoir trim completely at the top and bottom.
- Remove the underride protection (if present).
- Remove the underbody trim in front of the right rear wheel (no further use).
- Remove the fuel tank according to the manufacturer's instructions.
- Remove the glove compartment.
- Remove the A-pillar trim in the front passenger side footwell.
- Only with automatic air-conditioning: Remove the A/C control panel according to the manufacturer's specifications.
Heater installation location
1
Figure shows 1.8 lt engine
1 Heater
Installation location
1
5
Ford Focus / Focus C-MAX / Focus CC
Preparing electrical system
HG
X1
F3
4
Connect additional green/white (gn/ws) wire 5
to K3/86 and pull into protective sleeving.
rt/ws
gn/ws
86
87
87a
gn/ws
85
br
0,75mm²
Wiring diagram for
additional
wire
rt
5
rt
Only with automatic air-conditioning
30
K3
sw
4
rt
0,75mm²
Connect provided wires to IPCU as shown in
wiring diagram.
Connect 6 mm dia. cable lug to end of brown
(br) wire from IPCU/85 3.
15
IPCU
E
1
2
A
86
85
Premounting IPCU
connection
sw
br
0,75mm²
3
0,75mm²
6
Ford Focus / Focus C-MAX / Focus CC
Electrical system of Focus
Wiring harness pass through
Digital timer
1 Protective rubber plug detached
1 Digital timer
2 Summer/winter switch, drilled hole 12 mm dia.
1
1
2
2
3
i
Diagram
of wiring
harness
routing for
Focus
Do not install the metering pump
wiring harness until later together with fuel line along the original
vehicle fuel lines on the underbody
1
2
3
1
2
3
4
5
Fuse holder, K3 relay
Connection to battery
When drilling, watch components located behind.
Route wires (1) to left and fasten with cable ties.
2 K3 relay, 4 mm dia. hole, 5.5x13 self-tapping
screw
3 Fuse holder, 4 mm dia. hole, 5.5x13 mm selftapping screw
1 Wiring harnesses routed to right and fastened
with cable ties
2 Earth wire on negative battery terminal
3 Positive wire on positive battery terminal
7
Ford Focus / Focus C-MAX / Focus CC
Electrical system for Focus/Focus CC from 2008
Wiring harness pass through
Digital timer
1 Protective rubber plug detached
1 Digital timer
1
1
6
7
i
Diagram
of wiring
harness
routing for
Focus
Do not install the metering pump
wiring harness until later together with fuel line along the original
vehicle fuel lines on the underbody
1
2
3
1
2
3
8
9
Fuse holder, K3 relay
Connection to battery
When drilling, watch components located behind.
Route wires (1) to left and fasten with cable ties.
2 K3 relay, 4 mm dia. hole, 5.5x13 self-tapping
screw
3 Fuse holder, 4 mm dia. hole, 5.5x13 mm selftapping screw
1 Wiring harnesses routed to right and fastened
with cable ties
2 Earth wire on negative battery terminal
3 Positive wire on positive battery terminal
8
Ford Focus / Focus C-MAX / Focus CC
Electrical system of C-Max
Wiring harness pass through
Digital timer
1 Protective rubber plug detached
1 Digital timer
2 Summer/winter switch, drilled hole 12 mm dia.
1
1
2
10
11
i
Wiring
harness
routing diagram for
C-Max
Do not install the metering pump
wiring harness until later together with fuel line along the original
vehicle fuel lines on the underbody
1 2
1
12
1
13
Fuse holder, K3 relay
Wiring harness routing
Fastening will not be carried out until later after
reinstalling the coolant reservoir cap. When drilling, watch components located behind.
Connect earth wire to negative battery pole and
positive wire to positive battery pole.
1 Fuse holder, 4 mm dia. hole, 5.5x13 mm selftapping screw
2 K3 relay, 4 mm dia. hole, 5.5x13 self-tapping
screw
Route wiring harness (1) to right and fasten with
cable ties as shown.
9
Ford Focus / Focus C-MAX / Focus CC
1
Fan control without automatic A/C
2
Connection is carried out on connector C111,
Pin 22, at bottom of right-hand A-pillar.
Produce connections as shown in wiring diagram with blade connectors provided.
5
3
i
3 Connector C111
1 Red (rt) wire to K3/87a
Connect2 Green/orange (gn/or) wire from original ve- ing fan
hicle fan relay K14
motor
4 Wire to connector C111, Pin 22
5 Black (sw) wire from K3/30
14
4
i
Ford
Webasto
30
15
HG
F3
25A
X1
4
F10
30A
P91
32
C95
rt
1
gn/ws
K14
87
87a
5
2
sw/bl
86
3
rt/ws
gn/or
rt
sw
K3
85
sw/or
30
sw/rt
Wiring diagram without
automatic
air-conditioning
gn/or
22
C111
-
R21
br
M M3
A128
(23)
gn/or
+
sw
31
Webasto components
HG
Heater TT-E
F3
Fan fuse
K3
Fan relay
Ford components
F10
Fan fuse
K14
Fan relay
P91
Central electrical box
C111 Connector on right-hand
A-pillar
M3
Fan motor
R21
Resistor group
A128 Heater control module
23
Fan switch
Colours and symbols
rt
red
ws
white
sw
black
br
brown
gn
green
bl
blue
or
orange
X
Legend
Cutting point
10
Ford Focus / Focus C-MAX / Focus CC
Automatic A/C fan control
1
2
1
3
4
IPCU socket
4 mm dia. hole, 5.5x13 self-tapping screw
Brown (br) wire from IPCU/85
6 mm dia. cable lug, original vehicle bolt
IPCU fastening
2
4
15
3
1
2
3
4
5
7
Connection is carried out on 26-pin connector
C540, Pin 15.
Produce connections as shown in wiring diagram.
Connector C540
Connect IPCU
Green/white (gn/ws) wire from K3/86
Black (sw) wire from IPCU/A
Blue/white (bl/ws) wire to fan unit
Blue/white (bl/ws) wire from A/C control
module
2 Red (rt) wire to IPCU/E
6
1
3
4
5
7
Connecting airconditioning control
panel
16
6
1
1 Connector C540
2 Pin 15
2
View of
connector
17
1
Connection is carried out on connector C111,
Pin 22, at bottom of right-hand A-pillar.
Produce connections as shown in wiring diagram.
From 12/05, see page 12.
2
3
6
5
4
18
Connector C111
ConnecRed (rt) wire from K3/87a
tion to fan
Red (rt) wire from IPCU/15
Green/orange (gn/or) wire from original ve- unit
hicle fan relay K14
4 Green/orange (gn/or) wire to connector
C111, Pin 22
5 Black (sw) wire from K3/30 (on vehicles
from 12/05, see page 12)
3
1
6
2
11
Ford Focus / Focus C-MAX / Focus CC
X1
4
32
C95
rt
1
gn/
ws
30
15
F10
30A
P91
F3
25A
HG
i
Ford Focus/Focus C-Max
Automatic A/C until 12/05
Webasto
3
K14
rt/ws
5
2
sw/bl
gn/
or
rt
86
87
87a
sw
Wiring diagram for
automatic
air-conditioning
K3
85
30
A205
C540
rt
gn/
ws
16
bl/
ws
4
22
C111
1
15
IPCU
E
rt
2
86
br/
bl
sw
A
gn/
or
bl/
ws
85
6
5
3
br
15
gn/
or
2
3
M
1
C537
M3
sw
br
31
Webasto components
HG
Heater TT-E
X1
Connector on heater
F3
Fan fuse
K3
Fan relay
IPCU Pulse width modulator
IPCU settings:
Duty cycle: 60%
Frequency: 400Hz
Voltage:
10V
Function:
Low side
Vehicle components
F10
Fan fuse
K14
Fan relay
C111 Connector on right-hand Apillar
P91
Central electrical box
C95
Connector on P91
Colours and symbols
rt
red
ws
white
sw
black
br
brown
gn
green
bl
blue
M3
C537
A205
C540
or
Fan unit
Connector on M3
A/C control module (EATC)
Connector on A205
Legend
orange
X
Cutting point
Wiring colours may vary.
12
Ford Focus / Focus C-MAX / Focus CC
Additionally for automatic A/C
from 01/06
1
2
3
5
Produce connections as shown in wiring diagram.
1 Cut off green/orange (gn/or) wire of C111/3
and insulate
2 Green/orange (gn/or) wire of C111/3
3 Connector C111
4 Black (sw) wire of F4
5 Black (sw) wire of F4
Fan controller
19
4
1
2
3
Complete fuse holder with materials provided
and fasten it with double-sided adhesive
tape.
Produce connections as shown in wiring diagram.
1 Central electrical box in right-hand footwell
2 Black (sw) wires, 500 mm
3 Fuse holder, 10 A fuse
Fuse F4
20
13
Ford Focus / Focus C-MAX / Focus CC
X1
4
32
C95
rt
1
gn/
ws
30
15
F10
30A
P91
F3
25A
HG
i
Ford Focus/Focus C-Max
Automatic A/C from 01/06
Webasto
3
K14
rt/ws
5
2
sw/bl
gn/
or
rt
86
87
87a
F29
10A
sw
K3
85
gn/
or
30
C540
gn/
ws
16
bl/
ws
4
IPCU
E
C111
gn/
or
rt
gn/
or
sw
2
A
86
Wiring diagram for
automatic
air-conditioning
3
22
1
15
bl/
ws
85
6
5
3
br
15
!
F4
10A
A205
rt
gn/
or
4
M
2
1
C832/834
M3/A97
sw
br
31
Webasto components
HG
Heater TT-E
X1
Connector on heater
F3
Fan fuse
K3
Fan relay
IPCU Pulse width modulator
IPCU settings:
Duty cycle: 27%
Frequency: 400Hz
Voltage:
10V
Function:
Low side
Vehicle components
F10
Fan fuse
K14
Fan relay
C111 Connector on right-hand Apillar
P91
Central electrical box
C95
Connector on P91
Colours and symbols
rt
red
ws
white
sw
black
br
brown
gn
green
bl
blue
M3
C537
A205
C540
or
Fan unit
Connector on M3
A/C control module (EATC)
Connector on A205
Legend
orange
X
Cutting point
Wiring colours may vary.
14
Ford Focus / Focus C-MAX / Focus CC
Remote option (Telestart)
i
Receiver is mounted on existing bolt on positioning motor.
1 Original vehicle bolt
Installation location of
receiver
1
21
1 Receiver
1
Mounting
receiver
22
1 Antenna
1
Mounting
antenna
23
15
Ford Focus / Focus C-MAX / Focus CC
Preparing installation location
1
Cross member depends on vehicle equipment.
1 Cross member
2 M10 bolts [3x]
Removing
cross
member
2
2
24
2
Design of guard plate (2) depends on the vehicle equipment
1 Remove section and discard
2
Adapting
guard
plate
25
1
If threaded inserts are not present at position (1),
then mount M10 rivet nuts provided in hexagonal
holes.
Use special tool as shown on page 3.
For alternative, see next figure.
2
1 M10 steel rivet nut [2x]
2 Stud bolt
1
1
1
2
Installing
rivet nuts
26
1
2
3
4
3
4
M10 rivet nut (steel)
Washer
M10 nut
M10 bolt
Alternative rivetdown tool
27
16
Ford Focus / Focus C-MAX / Focus CC
Screw on flanged nut with flange toward front.
1
1 Original vehicle stud bolt
2 M8 flanged nut
2
Preparing
installation location
28
17
Ford Focus / Focus C-MAX / Focus CC
Premounting heater
1
1 Delivered heater assembly
B
Heater assembly
29
D
1
2
2 Delivered coolant assembly
1 Black (sw) rubber profile positioned in centre between spring clips
3 Remove connecting cable of circulating
pump and discard
C
Coolant
assembly
A
3
1
30
Hole in corner of strut is used at position 3.
Mount Ejot screw 3 only loosely, so that strut 2
can still be aligned during installation. Connect
wiring harness 4 to the circulating pump.
2
1 Retaining clip with intake silencer engaged
in hole
Connecting assemblies
3
4
B
D
C
31
General view.
Fix hoses B and C and wiring harness of circulating pump in place with cable ties.
C
Connecting assemblies
A
B
32
18
Ford Focus / Focus C-MAX / Focus CC
Fastening for underride protection
1
Vehicle-dependent, if present.
1 M6x25 bolt in existing 7 mm dia. hole
3 10 mm shim
2 Pin lock
Premounting heater
3
2
33
Installing heater
Only for 1.4 lt; 1.6 lt; 1.8 lt engine
Transport heater to installation location and
connect wiring harness as shown.
Installing
heater
34
Use holes in bracket as shown.
Check position of all components and adjust
if necessary. Check that they have freedom of
movement.
1 M10x30 bolt with locking toothing [2x]
Installing
heater
1
1
35
Use hole in strut as shown.
Check position of all components and adjust
if necessary. Check that they have freedom of
movement.
1
3
2
36
1 M8 flanged nut (premounted)
3 Flanged nut
2 Strut
Mounting
heater
Tighten Ejot screw (10 Nm).
19
Ford Focus / Focus C-MAX / Focus CC
Only for 2.0 lt engine
Transport heater to installation location and
connect wiring harness as shown.
Installing
heater
37
Use holes in bracket as shown.
Check position of all components and adjust
if necessary. Check that they have freedom of
movement.
1 M10x30 bolt, spring lockwasher [2x]
Installing
heater
1
1
38
Use hole in strut as shown.
Check position of all components and adjust
if necessary. Check that they have freedom of
movement.
1
3
1 M8 flanged nut (premounted)
3 Flanged nut
2 Strut
Mounting
heater
2
39
Tighten Ejot screw (10 Nm).
20
Ford Focus / Focus C-MAX / Focus CC
Coolant circuit
WARNING!
Any coolant running off should be collected in an appropriate container. Route hoses kink-free. Unless
specified otherwise, always fasten using cable ties. Position clamps so that other hoses cannot be
damaged. When installing the hoses, the heater must be filled with coolant.
The connection should be "inline" based on the following diagram:
1
C
D
Ø 25
Ø 20x18
A
Hose routing diagram
B
All spring clips without a specific designation
= 27 mm dia.
Undesignated connecting pipe
= 20x20mm dia. 1 = Black (sw) rubber isolator
21
Ford Focus / Focus C-MAX / Focus CC
1
1 Hose section of heat exchanger inlet
2 Engine outlet hose section
2
Cutting
point
40
1
2
3
Remove connection piece according to manufacturer's instructions. Locking device (3)
must be turned counterclockwise for this purpose.
i
2 Carefully saw open clamp
1 Discard hose
Preparing
coolant
41
1 Connection piece of heat exchanger inlet
mounted and locked
1
Preparing
coolant
42
1
D
2
Before connecting, fill the coolant hoses with
coolant.
3
1 Black (sw) rubber isolator between hose C
and D
2 Connection piece of heat exchanger inlet
3 Engine outlet hose section
C
A
43
Connecting hoses
Check routing of hoses and correct if necessary. Fasten wiring harness of heater to coolant hoses with cable tie.
22
Ford Focus / Focus C-MAX / Focus CC
Fuel
CAUTION!
Open the vehicle's fuel tank cap, ventilate the tank and then re-close the tank lock.
Collect any discharged fuel in an appropriate container.
Install fuel line and metering pump wiring harness so that they are protected against stone impact.
Unless specified otherwise, always fasten using cable ties.
Mount the fuel line and wiring harness with rub protection on sharp edges.
WARNING!
The fuel line and wiring harness of the metering pump are routed as shown in the wiring harness
routing diagram.
1
1 Mecanyl fuel line
2 10 mm dia. Caillau clamp
2
Connection to
heater
1
44
Route mecanyl fuel line to firewall and fasten
with cable ties as shown. Pay particular attention to sufficient distance from cardan shaft.
Installation location on right next to vehicle
fuel tank.
1
1 Angle bracket
2 M6x20 bolt, spring lockwasher on existing
threaded insert
2
Installation location of
metering
pump
45
1
2
3
1
2
4
3
5
6
2
4
6
5
Hose section
10 mm dia. Caillau clamp [2x]
180° moulded hose
Rubber-coated p-clamp
Silent block
Flanged nut
Premounting metering pump
46
23
Ford Focus / Focus C-MAX / Focus CC
1
2
Slide metering pump as far as possible upward in oblong hole.
Route fuel line and wiring harness as shown
in following illustration.
Fuel line to heater on pressure side of metering pump [side with connector].
3
6
4
3
1
2
6
5
5
1
4
Premounted metering pump
Flanged nut
Mecanyl fuel line
10 mm dia. Caillau clamp
Metering pump wiring harness
Completed connector housing
Mounting
metering
pump
47
1 Mecanyl fuel line and metering pump wiring harness
1
Wiring
routing
48
Removing fuel
1
2
Remove fuel-tank sending unit (4) in accordance with manufacturer's instructions.
Break out connection piece (2) at rupture joint (1)
with suitable tool (3) according to manufacturer's
instructions.
Fuel
removal
3
4
i
49
Install fuel standpipe (Ford Order No. Finis
Code 1233999) according to manufacturer's
instructions.
1
2
i
1 Fuel standpipe
2 Removal hose
Installing
fuel standpipe
50
Align removal hose up to bottom of fuel tank.
Ensure freedom of movement of fuel gauge.
24
Ford Focus / Focus C-MAX / Focus CC
Install fuel-tank sending unit according to
manufacturer's instructions.
Mount coupling and align; remove clip at Position 3.
1
2
5
4
51
3
1
1
2
5
4
3
Fuel standpipe
Coupling piece, mounted on fuel standpipe ConnectMecanyl fuel line
ing fuel
10 mm dia. Caillau clamp
line
Clip
Reinstall fuel tank.
Fuel line from fuel standpipe on intake side of
metering pump [side without connector].
2
1 Fuel line
2 10 mm dia. Caillau clamp
Connection to metering
pump
52
Check the position of the components; adjust
if necessary. Check that they have freedom of
movement.
Align fuel lines and wiring harness of metering pump over entire length and secure with
cable ties.
25
Ford Focus / Focus C-MAX / Focus CC
Mounting underride protection
For all vehicles!
Underride protection is dependent on vehicle
equipment.
Cut out underride protection as shown.
Cutting
out underride protection
53
1
Only for 1.4 lt; 1.6 lt; 1.8 lt engine
2
Remove plastic threaded insert.
Drill out hole to 9 mm dia. and insert M6 rivet
nut.
1
2
3
4
Bracket of heater
M6 rivet nut, 10 mm shim
Underride protection
M6x40 bolt, spring lock washer, large diameter washer
3
54
4
1
Mounting
underride
protection
for 1.4 lt;
1.6 lt; 1.8 lt
engine
Only for 2.0 lt engine.
2
1
2
4
3
Bracket of heater
Premounted bolt
Underride protection
M6 flanged nut, large diameter washer
Mounting
underride
protection
for 2.0 lt
engine
3
55
4
For all vehicles!
1
Figure shows 1.8 lt engine
Check positioning of underride protection. In
particular, ensure sufficient distance from
heater exhaust system. Rework cut-out if
necessary.
Also fasten underride protection for stabilization with cable ties at position (1).
Mounting
underride
protection
for all vehicles
56
26
Ford Focus / Focus C-MAX / Focus CC
Final Work
WARNING!
Mount removed parts in reverse order. Check all hoses, clamps and all electrical connections for firm
seating. Insulate and tie back all loose wires.
Only use manufacturer-approved coolant. Spray heater components with anti-corrosion wax (Tectyl
100K, Order No. 111329).
-
Connect the battery.
Fill and bleed the coolant circuit according to the vehicle manufacturer’s specifications.
Adjust digital timer, teach Telestart sender
Make settings on A/C control panel according to the "Operating Instructions for End Customer".
- Place signboard "Switch off parking heater before refuelling" in the area of the filler neck
- See installation instructions for initial startup and function check
i
Feel the drive
Webasto AG
Postfach 80
D-82132 Stockdorf / Germany
National Hotline: 01805 93 22 78
(14 Cent aus dem deutschen Festnetz)
Hotfax: 0395 5592 353
Hotmail: technikcenter@webasto.com
http://www.webasto.com
1303854F_EN
Printed in Germany
01/2012
Printing: Steffen
27
Ford Focus / Focus C-MAX / Focus CC
Operating instructions for end customer
Please remove page and add to the vehicle operating instructions.
WARNING:
On vehicles with "Flexyfuel" engine, operation of parking heater is only permissible with petrol.
Note:
We recommend matching the heating time to the driving time.
Heating time = driving time
Example:
For a driving time of approx. 20 min. (in one direction), we recommend not exceeding a switch-on time
of 20 min.
i
Before parking the vehicle, make the following settings:
1
1 Set fan to level "2", or possibly "1"
2 Air outlet to windscreen
3 Set temperature to "max."
2
For vehicles without
automatic
air-conditioning
57
3
1
2
1 Temperature to "max." [2x]
2 Air outlet to windscreen
1
For vehicles with
automatic
air-conditioning
58
1
2
1 Temperature to "max." [2x]
2 Air outlet to windscreen
1
For vehicles with
automatic
air-conditioning
59
28