VR1® Glute
Owner’s and Service Manual
Strength Systems
Part Number 13170-999-4 C
www.cybexinternational.com
VR1® Glute
Owner’s and Service Manual
Strength Systems
Part Number 13170-999-4 C
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
VR1® and its mark are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • 13170-999-4 C •March 2010
Table of Contents
1 Safety
Safety . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Guidelines and Practices . . . .
Warning/Caution Decals . . . . . . . . . .
Regular Maintenance Activities . . . . .
Use Proper Form. . . . . . . . . . . . . . .
1-1
1-2
1-3
1-6
1-6
2 Exercises
Intended Use. . . . . . . . . . . . . . . . . . . 2-1
Instructions . . . . . . . . . . . . . . . . . . . 2-2
3 Customer Service
Contacting Service . . . . . . . . . . . . . .
Ordering parts . . . . . . . . . . . . . . . . . .
Return Material Authorization (RMA).
Damaged Parts . . . . . . . . . . . . . . . . .
3-1
3-1
3-2
3-2
4 Assembly . . . . . . . . . . . . . . . . . . . . . 4-1
5 Maintenance
Daily Procedures . . . . . . . . . . . . . . . .
Weekly Procedures . . . . . . . . . . . . . .
Yearly Procedures . . . . . . . . . . . . . . .
Cable Adjustments . . . . . . . . . . . . . . .
Environment. . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . .
5-1
5-4
5-5
5-6
5-7
5-7
6 Service . . . . . . . . . . . . . . . . . . . . . . . 6-1
Page i
Cybex VR1 13170 Glute Owner’s Manual
1 - Safety
Safety
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the
equipment and review all labels.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
•
Obtain a medical exam prior to beginning an exercise program.
•
Read and understand warning labels and user manual prior to exercising. Obtain instruction
prior to use.
•
Keep body and clothing free from and clear of all moving parts.
•
Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
•
DO NOT attempt to fix a broken or jammed machine. Notify floor staff.
•
Use the machine only for the intended use. DO NOT modify the machine.
•
Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer.
If unsure seek assistance.
•
Never pin the weights in an elevated position. DO NOT use the machine if found in this condition.
See assistance from floor staff.
•
Children must not be allowed near these machines. Teenagers must be supervised.
•
DO NOT use if guards are missing or damaged.
•
DO NOT use dumbbells or other incremental weights, except those provided by the manufacturer.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
•
DO NOT remove any labeling from equipment. Replace any damaged labels.
•
Stop exercising if you feel faint, dizzy or experience pain at any time while exercising and consult your
physician.
Facility Safety Precautions
•
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
•
Securely anchor each machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional
contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any
leg or frame not in contact with surface using flat washers.
Safety
Page 1-1
Cybex VR1 13170 Glute Owner’s Manual
•
Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an
uneven surface.
•
Make sure that all users are properly trained on how to use the equipment.
•
Make sure there is enough room for safe access and operation of the equipment.
•
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most susceptible to wear,
including (but not limited to) cables, pulleys, belts and grips.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or damaged components
then remove from service until the repair is made.
•
Use only Cybex supplied components to maintain/repair the equipment.
•
Keep a repair log of all maintenance activities.
•
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance is performed.
Safety Guidelines And Practices
Cybex recommends that all fitness equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion of
the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.
Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has the
proper clearance for usage and training.
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the floor. Cybex strongly recommends that,
to eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level
surface.
1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defined and required by local
building and architectural codes.
2. Anchoring of equipment must be completed by a qualified licensed contractor.
Safety
Page 1-2
Cybex VR1 13170 Glute Owner’s Manual
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the
equipment to the floor.
4. Due to the wide variation of flooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualified and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specified in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals show where each
decal is located.
Safety
Page 1-3
Cybex VR1 13170 Glute Owner’s Manual
A
CAUTION
Personal injury may occur.
Keep away from moving
parts to avoid injury.
4000Y316-4
B
C
4605-381-4 A
Safety
Page 1-4
Cybex VR1 13170 Glute Owner’s Manual
Glute - 13170
A
B
C
(both sides)
B
Description
Part No.
A. Warning Label....................4605-381-4
B. Caution Decal.....................4000Y316-4
C. Caution Decal.....................8500-025-4
Safety
Page 1-5
Cybex VR1 13170 Glute Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of your equipment.
Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative
maintenance activities. The preventative maintenance actions are described in detail in Chapter 5.
Briefly, they include:
Daily
1. Clean upholstery.
Weekly
1. Inspect all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables and belts for damage or wear (see Chapter 5). If a cable or belt is worn
or damaged, immediately discontinue use until cable or belt has been replaced.
3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts
immediately.
4. Inspect for loose or worn grips. Replace all worn grips immediately.
5. Inspect weight stacks for proper alignment and operation. Correct all improper alignment
and operation issues immediately.
6. Lubricate guide rods using automotive engine oil only.
Yearly
1. Replace all cables and belts at least annually.
Using Proper Form
Before working out, read and understand the exercises located on the placard and in Chapter 2.
Safety
Page 1-6
Cybex VR1 13170 Glute Owner’s Manual
2 - Exercise
MUSCLES USED
Intended Use
The intended use of this equipment is to aid or
improve general physical fitness and exercise. For
Commercial use.
Instructions
Read and understand all instructions and warnings
prior to using this machine. See Chapter 1, Safety, in
the Owner’s Manual or consult with floor staff.
START
Gluteus Maximus,Hamstrings,
Quadriceps
FINISH
NOTE: Motion Developed: Hip Extension,Knee Extension
NOTE: All adjustment points on the machine have yellow handles or knobs.
NOTE: See next page for “Set Up” and “Movement.”
Exercise
Page 2-1
Cybex VR1 13170 Glute Owner’s Manual
Set Up
1. Adjust abdominal pad for comfortable support.
2. Rest lower leg and forearms on pads and grasp handles.
3. Place foot of opposite leg against foot bar.
Movement
1. Push to rear and upward while maintaining body position.
NOTE: Maintain contact with footbar at all times.
Exercise
Page 2-2
Cybex VR1 13170 Glute Owner’s Manual
3 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300
or fax 508-533-5183.
Find information on the web at www.cybexintl.com or by e-mail at techhelp@cybexintl.com.
Ordering Parts
Fax orders to 508-533-5183. To speak with a customer service representative, call 888-462-9239 (for customers
living within the USA) or 508-533-4300 (for customers outside the USA). You may also contact us through e-mail
at techhelp@cybexintl.com
Having the following information ready when calling will assist our Cybex representatives in serving you.
•
•
Unit Serial Number
Product Name
The unit serial number and product name can be found on the serial number decal. See Chapter 6 for
exact location of serial number decal.
•
•
Part Description
Part Number
Part descriptions and part numbers are located in Chapter 6 of this manual.
•
•
Shipping Address
Contact Name
In addition to your shipping address and contact name, your account number is helpful but not
required.
Customer
Service
Page 3-1
Cybex VR1 13170 Glute Owner’s Manual
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for placement, repair or credit. The system assures that returned materials are properly handled and
analyzed. Follow the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA
from Cybex, if applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without
proper RMA and an Automated Return Service (ARS) label.
1. Call the Customer Service Hot Line listed above for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the item you
wish to return.
3. Provide the model and serial number of your Cybex equipment.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for evaluation
and repair or replacement. The technician will assign you a RMA number and will send you an ARS label.
The ARS label and the RMA numbers must be clearly displayed on the outside of the package that contains
the item(s) to be returned. Include the description of the problem, the serial number of the VR1 equipment
and the name and address of the owner in the package along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent COD will
not be accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility of the
carrier (UPS, Federal Express, trucking companies, etc.)
Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a visual
check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result in the carriers
refusal to honor your damage claim. The carrier will provide you with the required forms for filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but
notices later must be reported to the carrier as soon as possible. Upon discovery of the
damage, a written or phone request to the carrier asking them to perform an inspection of the materials must
be made within ten days of the delivery date. Keep all shipping containers and packing materials as they will be
needed in the inspection process. The carrier will provide you with an inspection report and the necessary forms
for filing a concealed damage claim. Concealed damage claim is the carrier’s responsibility.
Customer
Service
Page 3-2
Cybex VR1 13170 Glute Owner’s Manual
4 - Assembly
Tools Required
•
•
•
•
7/32” Allen wrench
3/4” Socket or wrench
Hammer
3/16” Pin punch
NOTE: Two people will be required to perform this procedure.
NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is
appropriate clearance around each machine to allow for safe use and passage.
NOTE: Refer to Chapter 6 for reference diagrams.
1. Read and understand all instructions thoroughly before assembling this product.
2. Verify you have received the appropriate configuration.
A. Verify that you received the correct color machine that you ordered.
B. Verify you received the proper weight stack and weight stack decals.
C. Verify you received the appropriate owner’s manual.
D. Verify you received the warranty sheet.
3. Move to desired location.
NOTE: If weight stacks need to be removed before moving to desired location proceed to step 7.
NOTE: If weight stacks need to be installed proceed to step 8.
4. Remove shipping feet.
WARNING: Use extreme caution when removing shipping cones and installing feet. Failure to do so
could result in injury.
A. With an assistant, carefully remove each (standard) cone-shaped shipping support using a 3/4” socket
or wrench.
B. Carefully place rubber feet (supplied with machine) on each foot of the frame.
NOTE: It is important that you perform regular inspection and maintenance activities on your equipment. See
the CYBEX VR1 Owner’s Manual for inspection and maintenance activities. If you do not have a CYBEX
Owner’s Manual or if you have any questions or concerns, Call Cybex Customer Relations at
888-462-9239.
Assembly
Page 4-1
Cybex VR1 13170 Glute Owner’s Manual
5. Securely anchor machine to the floor.
A. Securely anchor machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional contractor.
NOTE: Use fasteners having a minimum of 500 lbs tensil capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not in
contact with surface using flat washers.
6. Verify proper operation.
7. Removing weight plates.
A. Using a 7/32” Allen wrench, remove the two Button Head Socket Cap Screws (BHSCS) securing the top
cap to the frame. See Figure 1.
BHSCS
Shroud
Top Cap
Figure 1
B. Remove top cap and BHSCS and set aside.
C. Carefully lift shroud up and out of machine.
D. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. NOTE: Guide rod cap is
spring loaded.
E. Slowly release grasp
of guide rod cap.
See Figure 2. NOTE:
Guide rod cap
contains a
compression spring
that will fly if grasp is
not released slowly.
Compression
Spring
Figure 2
Assembly
Page 4-2
Guide
Rod Cap
Guide
Rod Cap
Guide
Rods
Compression
Spring
Cybex VR1 13170 Glute Owner’s Manual
F. Remove guide rod cap and spring and set aside.
G. Repeat steps 7D - 7F for other guide rod.
H. Using a 3/16” pin punch and hammer, carefully remove roll pin securing cable end to top weight
connector. See Figure 3.
I.
Carefully lean guide rods slightly outward. NOTE: Excessive pressure on guide rods may damage lower
guide rod caps.
Cable End
Top Weight
Connector
Roll Pin
Figure 3
J. Slide top weight up and out of machine and carefully set aside.
K. Have an assistant hold guide rods vertical.
L. Carefully remove each weight plate and set aside.
M. Wipe guide rods clean over entire length. Lubricate with light coating of medium weight automotive engine
oil.
8. Installing weight plates.
A. Have an assistant hold guide rods vertical.
B. Carefully align weight plates (removed in step 7M) over guide rods and slowly lower each weight plate.
NOTE: Install weight plates in reverse order as removed in step 7M. NOTE: When installing weight plates,
position plates so wide edges of bushings face upward and narrow edges of bushings face downward.
See Figures 4A and 4B.
T
C
RE
R
O
C
WIDE bushing
edge faces
upward
Figure 4A
G
N
RO
W
NARROW
bushing edge
NOTE: The narrow
bushing edge must face
downward.
Figure 4B
Assembly
Page 4-3
Cybex VR1 13170 Glute Owner’s Manual
C. Repeat steps 8A and 8B for each weight plate.
D. Carefully slide top weight (removed in step 7J) over guide rods.
9. Cable routing.
A. Verify cable is routed through top of pulley bracket and then route cable end to top weight
connector.
B. Pull cable tight and secure in place with roll pin removed in step 7H.
C. Place weight stack pin in each plate to verify proper installation.
D. Without selecting any resistance, lift top weight up and down (simulating normal operation).
E. Have an assistant verify that the cable is moving smoothly and is routed straight from the pulley bracket to
the top of the weight plate connector.
10. Install back shroud.
A. Carefully place shroud into position.
B. Secure top cap in place with the two BHSCS removed in step 7A.
11. Complete Steps 4 and 5.
Assembly
Page 4-4
Cybex VR1 13170 Glute Owner’s Manual
5 - Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing routine preventive
maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems equipment.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines.
Instruct all personnel in equipment inspection and maintenance actions and also in accident
reporting/recording. Cybex phone representatives are available to answer any questions or concerns that
you may have.
NOTE: All inspections and
repairs must be performed
by trained service
personnel only.
Cybex will void warranty if
non-Cybex replacement
parts are used.
Daily Procedures
1. Upholstery - Wipe down all upholstery as per the recommendations listed below for light soiling and more
difficult stains.
Light Soiling
•
A solution of 10% household liquid soap with warm water applied with a soft damp cloth.
•
If necessary, a solution of liquid cleanser and water applied with a soft bristle brush. Wipe away the residue
with a water dampened cloth.
Maintenance
Page 5-1
Cybex VR1 13170 Glute Owner’s Manual
More Difficult Stains
•
Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite),
90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration.
•
•
The same procedure can be used with full strength household bleach, if necessary.
Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately
30 minutes. Rinse with a water dampened cloth to remove any remaining bleach concentration.
Alternative Method for Difficult Stains
•
Dampen a soft white cloth with rubbing alcohol and rub gently. Rinse with a water dampened cloth to remove
any remaining rubbing alcohol concentration.
NOTE: To restore luster, a light coat of spray furniture wax can be used. Apply for 30 seconds and
follow with a light buffing using a clean white cloth.
Please Review Carefully
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to first test in an
inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to formula
changes by the product manufacturer without notice. Should you desire to use other
cleaning agents, carefully try them in an inconspicuous area to determine potential damage to the material.
Never use harsh solvents or cleaners which are intended for industrial applications. To clean stained or soiled
areas, a soft white cloth is recommended. Avoid use of paper towels.
Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye
protection. Do not inhale or swallow any cleaning product. Protect surrounding area/clothing from
exposure. Use in well ventilated area. Follow all product manufacturer’s warnings. CYBEX and its vendors
cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning products.
2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could
scratch or damage the equipment.
3. Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral cleaners with
a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners
and also cleaners containing abrasives as these could scratch or damage the equipment.
Maintenance
Page 5-2
Cybex VR1 13170 Glute Owner’s Manual
4. Guidelines for cleaning front panel:
•
Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
•
•
•
Follow up the application with warm water rinse.
•
•
Don’t apply cleaners in direct sunlight or at elevated temperatures.
•
Don’t clean with gasoline.
Don’t use abrasives or high alkaline cleaners.
Don’t leave cleaners on for long periods, wash immediately.
Don’t use scrapers, squeegees or razors.
Compatible Cleaners and Detergents:
•
•
•
Formula 409
•
•
Palmolive
Top Job
Joy
Windex with Ammonia D
To Minimize Fine or Hairline Scratches:
Mild automotive polish applied and removed with a soft, clean cloth will help fill scratches.
Suggested Polishes:
•
Johnson Paste Wax
•
Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)
•
Novus Plastics Polish #1, #2 (By Novus Inc.)
Maintenance
Page 5-3
Cybex VR1 13170 Glute Owner’s Manual
Weekly Procedures
1. Check all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables for wear or damage and proper tension. When inspecting cables, run fingers on the cable,
paying particular attention to bends in cable and attachment points.
WARNING: Replace all worn cables immediately. The following conditions may indicate a worn cable:
•
A tear or crack in the cable sheath that exposes the cable. See Figure 1.
Figure 1.
•
A kink in the cable. See Figure 2.
Figure 2.
•
A curled sheath. See Figure 3.
Figure 3.
•
“Necking”, a stretched cable sheath. See Figure 4.
Figure 4.
Maintenance
Page 5-4
Cybex VR1 13170 Glute Owner’s Manual
3. Inspect bars and handles for wear, paying particular attention to tab area connection points.
Replace all worn handles immediately.
CAUTION: Replace all worn handles immediately. Do not use if less than 1/8” of material
remains to the edge. See Figure 5.
Attachment Hole
NOTE: Replace bar if less
than 1/8” of material
remains to the edge.
Figure 5
4. Inspect snap links for proper latching (indicates wear)
Replace all worn snap links immediately.
5. Inspect for loose or worn grips.
Replace all loose or worn grips immediately.
6. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.
Replace all worn labeling immediately.
7. Inspect all weight stacks for proper alignment and operation.
Correct all improper alignment and operation issues immediately.
8. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium weight
automotive engine oil.
Yearly Procedures
1. Replace all cables at least annually.
Maintenance
Page 5-5
Cybex VR1 13170 Glute Owner’s Manual
Cable Adjustment
Three types of cable tension adjustment are used on Cybex Strength Systems:
1. Jam Nut Adjustment - This type uses a jam nut
and a tension adjustment nut at the cable cam end
as the primary adjustment. The other end of the cable
usually contains a roll pin adjustment. See Figures 6 and 7.
2. Rod End Adjustment - This type of adjustment contains
a socket head cap screw (SHCS) securing a cable rod end
bearing to the machine. Primary adjustment is by turning the
rod end bearing. The other end of the cable usually contains
a roll pin cable adjustment. See Figures 7 and 8.
3. Roll Pin Adjustment - This type of adjustment utilizes a roll
pin and series of holes in the weight stack top weight
connector. See Figure 8.
Tension
Adjustment
Nut
Jam Nut
Figure 6
Cable End
Frame
SHCS
Jam Nut
Cable Rod End
Bearing
Nylon
Locknut
Figure 7
Roll Pin
Cable End
Top Weight
Connector
Figure 8
Maintenance
Page 5-6
Cybex VR1 13170 Glute Owner’s Manual
Environment
Static Electricity - Depending upon where you live, you may experience dry air, causing a common experience
of static electricity. This may be especially true in the winter time. You may notice a static build-up just by walking
across a carpet and then touching a metal object. The same can hold true while working out on your unit. You
may experience a shock due to the build-up of static electricity on your body and the discharge path of the unit.
If you experience this type of situation, you may want toincrease the humidity to a comfortable level through the
use of a humidifier.
Humidity - The unit is designed to function normally in an environment with a relative humidity range of 30% to
75%.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna,
indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely
affect the electronics as well as other parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient temperature range
of 50 F (10 C) to 104 F(40 C) degrees.
o
o
o
o
Storage
Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%.
NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the
electronics as well as other parts of the machine.
Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of 32
F (0 C) and 140 F (60 C) degrees.
o
o
o
Maintenance
Page 5-7
Cybex VR1 13170 Glute Owner’s Manual
This page intentionally left blank.
Maintenance
Page 5-8
Cybex VR1 13170 Glute Owner’s Manual
6 - Service
Please refer to the next several pages for parts lists, exploded-view diagrams and cable
and belt routing diagrams.
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Service
Page 6-1
Cybex VR1 13170 Glute Owner’s Manual
This page intentionally left blank.
Service
Page 6-2
Cybex VR1 13170 Glute Owner’s Manual
GLUTE
PRODUCT NO. 13170
L
K
A
D
J
H
B (both sides)
G
C
B
F
M
G
NOTE: See exploded-view diagram for location of E (cable) and I (serial number decal)
A.
B.
C.
D.
E.
F.
DESCRIPTION
PART NO.
Placard Decal ....................
Caution Decal ....................
Caution Decal ....................
Warning Label ...................
Cable..................................
Chest Pad....................... ...
13170-598
4000Y316
8500-025
4605-381
13170-002
4800-188
DESCRIPTION
G.
H.
I.
J.
K.
L.
M.
PART NO.
Arm/Knee Pad..................... 4800-183
Grip ................................... 4605-520
Serial Number Decal
Weight Selector Pin............ BH030207
Water Bottle Holder............ 13000-400
VR1 Decal........................... 13000-399
Grip 21”............................... 12170-333
Service
Page 6-3
Service
Page 6-4
1- German
2- French
3- Spanish
4- English
6- Japanese
7- Swedish
8- Russian
*Language Key
QTY
5
1
1
2
2
2
1
1
1
2
2
4
2
2
2
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
4
1
1
4
4
4
2
1
2
2
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
DESCRIPTION
08014
PULLEY ASSEMBLY, 4.50 IN.
11040-440
KNOB
11070-332
C/ COUNTERWEIGHT
11090-374
END CAP
11090-376
RING, HANDLE GRIP
11170-345
END CAP
12030-353
BLOCK, STOP
12170-204
W/ PAD MOUNT
12170-333
GRIP,21.00
12210-347
GUIDE ROD CAP
12210-348
GUIDE ROD CAP
12210-352
PLASTIC INSERT
12210-359
SPACER TUBE
13000-322
ROLLER
13000-326
WT ROD .625 DIA X 51.51
13000-342
MOLDED TOP CAP
13000-353
FOOT PAD
13000-354
FOOT PAD
13000-355
FOOT PAD (NOT SHOWN)
13000-364
BEARING, FLANGE .62 ID. x .92 OD. x 1.75 LG
13000-400
HOLDER, WATER BOTTLE
13000-403
MOUNT, WATER BOTTLE HOLDER
13170-002
CABLE S/A
13170-200
MAIN FRAME
13170-201
INPUT
13170-202
ADJUSTING POST
13170-203
W/PIVOT
13170-317
SHAFT, PIVOT
13170-326
TIE ROD
13170-331
SHAFT, PIVOT
3900-438
DECAL, CYBEX
4505-329
P/PIN,DETENT
4605-512
INSERT PLASTIC, 7.94
4700c070
C/TOP WEIGHT, 15, 3 x 12
BH030207
PIN, WEIGHT SELECTOR
BR030206
RING, RETAINING
BR030220
RETAINING RING 1.250 INTERNAL
BS070201
COM SPRING .56 x .66 1.50 LG
BS070208
COMPRESSION SPRING
CM000211
DECAL, PATENT PENDING
(REMOVED 7/6/09)
FB030213
ROD END BEARING FEMALE .375-24 UNF
FB030232
BEARING, RADIAL 17 mm EXTENDED RACE
FB030250
BRG ROD END MALE .500-20 RH
FB030251
BRG ROD END MALE .500-20 LH
FC030006
TOLERANCE RING 1.575 ID
HC700414
BHSCS .375-16 X .625
HC700417
BHSCS .375-16 X 1.00
HC700426
BHSCS .375-16 X 2.00
HC700430
BHSCS .375-16 X 2.50
HF449063
INSERT 3/4 X 1/4-20
HF700000
PANEL FASTNER, .375-16, U TYPE
PART NO.
9
1
3
1
2
2
2
1
2
2
4
9
2
5
1
1
1
8
2
2
2
1
1
2
2
2
1
3
3
1
1
1
1
1
1
8
1
1
1
1
1
14
14
1
1
1
1
1
1
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
QTY
52
53
54
55
56
57
58
ITEM
JC620415
JC620422
JC700412
JC700420
JC700422
JC700424
JN714400
JN794400
JN794401
JS347400
JS388300
JS497600
PN660200
PP080226
PP130002
PP130003
PR060005
4605-520
4800-188
4800-017
4000Y316-X*
8500-025-X*
4605-381-X*
13000-399
13000-101
13000-102
13040-100
HT552511
13000-208
13170-999-X*
13000-343
13000-346
13170-598-X*
13000-032
13000-036
4700-337
4700-338
4800-557
13000-552
13000-398
11040-790
HT552515
HN704901
HP286819
HS347600
HS347700
HS720004
HS760106
HT512517
PART NO.
LOCKNUT, .375-16 NYLON
SPIRAL PIN .188 X 1.12
WASHER, SAE .375
WASHER, USS .375
WASH, FELT .641 1.250 .125T
WASHER, FLAT, 1.75 X .688 X .140 T
TAP SC 10-24 X 1.00 TYPE WB PN HD
PHIL BLK
TAP SC NO. 8-16 X .75 PLASTITE PN
HD PHIL BLK
BHSCS .250-20 X .75
BHSCS .250-20 x 1.50
BHSCS .375-16 X .50
BHSCS .375-16 X 1.25
BHSCS .375-16 X 1.50
BHSCS .375-16 X 1.75
NUT, HEX JAM .375-24 UNF
JAM NUT .500-20
JAM NUT .500-20 LH
LOCKWASHER, INT TOOTH .375
SPLIT LOCKWASHER .500
WASHER, 1.19 ID x 1.75 OD x .12 THK
INSERT, PLASTIC 1.00 DIA-11 GA
INSERT, DOMED PLASTIC 2.00, RIB
INSERT, DOMED PLASTIC
INSERT, DOMED PLASTIC
BUMPER, WEIGHT
GRIP 1.38 OD X .94 ID 6.25”
CHEST PAD
ARM/KNEE PAD
DECAL,CAUTION
DECAL,CAUTION
DECAL, WARNING
DECAL, VR1
5LB 1/2 WEIGHT OPTION
7.5LB 1/2 WEIGHT OPTION
EDGE TRIM
TAP SCREW 8-16X.38 BLACK
LATCH
OWNER’S MANUAL (NOT SHOWN)
FRONT PANEL
BACK PANEL
PLACARD, GLUTE
WEIGHT PLATE PACK (LIGHT)
WEIGHT PLATE PACK (STANDARD)
WEIGHT PLATE (LIGHT) 10LB
WEIGHT PLATE (STANDARD) 15LB
DECAL, WEIGHT PLATE 10-150
DECAL, WEIGHT PLATE 10-220
DECAL, CYBEX
DECAL, MADE IN U.S.A.
DESCRIPTION
Cybex VR1 13170 Glute Owner’s Manual
50
75
69
5
77
4
61
63
61
79
4
5
63
50
69
8
63
69
79
75
63
63
69
69
74
26
52
46
49
46
69
23
62
54
Serial
Number
Decal
2
38
33
80
63
81
78
63
69
64
6
69
63
79
32
54
9
60
62
60
28
17
3
30
63
62
7
55
54
45
42
25
27
73
62
42
45
52
45
42
70
47
70
43
6
21
29
44
68
59
67
GLUTE MAIN ASSEMBLY DETAIL
80
64
42
45
58
58
52
1
18
22
72
65
1
1
52
65
52
72
65
Cybex VR1 13170 Glute Owner’s Manual
Service
Page 6-5
Service
Page 6-6
86
86
99
85
86
86
91
83
98
89
87
82
52
52
52
52
51
11
65
47
65
35
14
48
14
1
24
51
16
47
13
12
12
57
76
20
56
65
1
15
39
10
71
10
76
71
13
12
12
57
36
34
53
20
56
37
15
39
GLUTE PANEL AND WEIGHT PACK DETAIL
94
90
34
10lb
92
96
95
15lb
WEIGHT PLATE DETAIL
31
93
97
Cybex VR1 13170 Glute Owner’s Manual
53
23
Glute Cable Routing
52
41
66
34
63
27
Cybex VR1 13170 Glute Owner’s Manual
Service
Page 6-7
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • Techhelp@cybexintl.com