iii
iv
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer
makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose.
The manufacturer reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
AMD, Athlon, Sempron and Duron are registered trademarks of AMD Corporation.
Other product names used in this manual are the properties of their respective owners and
are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this
equipment to ensure compliance with the pertinent RF emission limits governing this
device. Changes or modifications not expressly approved by the system’s manufacturer
could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference
that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le
matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Describes features of the motherboard.
Introducing the Motherboard
Go to
H
page 1
Describes installation of motherboard
components.
Chapter 2
Installing the Motherboard
Go to
H
page 7
Provides information on using the BIOS
Setup Utility.
Chapter 3
Using BIOS
Go to
H
page 27
Chapter 4
Describes the motherboard software
Using the Motherboard Software
Go to
Preface
H
page 47
iii
TABLE OF CONTENTS
Preface
i
Chapter 1
1
Introducing the Motherboard
1
Introduction.................................................................................................1
Feature..........................................................................................................2
Motherboard Components........................................................................4
Chapter 2
7
Installing the Motherboard
7
Safety Precautions......................................................................................7
Choosing a Computer Case.......................................................................7
Installing the Motherboard in a Case......................................................7
Checking Jumper Settings.........................................................................8
Setting Jumpers..............................................................................8
Checking Jumper Settings..............................................................9
Jumper Settings..............................................................................9
Connecting Case Components...............................................................10
Front Panel Header.....................................................................12
Installing Hardware...................................................................................13
Installing the Processor...............................................................13
Installing Memory Modules.........................................................15
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17
Installing a Floppy Diskette Drive...............................................19
Installing Add-on Cards..............................................................20
Connecting Optional Devices......................................................22
Connecting I/O Devices..........................................................................25
Chapter 3
27
Using BIOS
27
About the Setup Utility............................................................................27
The Standard Configuration........................................................27
Entering the Setup Utility..............................................................27
Updating the BIOS.......................................................................29
Using BIOS................................................................................................29
Standard CMOS Features...........................................................30
Advanced BIOS Features.............................................................32
Advanced Chipset Features.........................................................34
iv
Integrated Peripherals.................................................................36
Power Management Setup...........................................................40
PNP/PCI Configurations.............................................................42
PC Health Status..........................................................................43
Frequency/Voltage Control..........................................................44
Load Performance Defaults.........................................................45
Load Optimized Defaults.............................................................45
Set Supervisor/User Password....................................................45
Save & Exit Setup.........................................................................46
Exit Without Saving......................................................................46
47
Chapter 4
Using the Motherboard Software
47
About the Software CD-ROM................................................................47
Auto-installing under Windows 2000/XP.............................................47
Running Setup..............................................................................48
Manual Installation..................................................................................50
Utility Software Reference.......................................................................50
Multi-Language Translation
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the RX480-A motherboard. This motherboard is a high performance, enhanced function motherboard that supports Socket 939 AMD Sempron/Athlon
64/Athlon 64 FX and CPUs for high-end business or personal desktop markets.
The motherboard incorporates the RX480 Northbridge (NB) and SB400 Southbridge (SB)
chipsets. The Northbridge supports the HyperTransport (HT) interface speeds up to
2000MT/s data rate. It supports four DDR Sockets with up to maximum memory size of
4GB. One PCI Express x16 slot, intended for Graphics Interface, is fully compliant to the
PCI Express Base Specification revision 1.0a.
The SB400 Southbridge supports three PCI slots which are PCI 2.3 compliant. In addition,
two PCI Express x1 slots are supported, fully compliant to the PCI Express Base Specification, Revision 1.0a. It implements an EHCI compliant interface that provides 480Mb/s
bandwidth for eight USB 2.0 ports (rear panel x 4, header x 4). Two onboard IDE connectors
supports 4 IDE devices in UDMA 133/100/66/33 modes. The Southbridge integrates a Serial
ATA host controller that is SATA v1.0 compliant, supporting four SATA ports with maximum transfer rate up to 150 MB/s each.
The RX480-A motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 mouse and keyboard connectors, COM1, LPT1, four USB ports, one optional LAN port, and audio jacks for microphone, line-in and 8-ch line out.
Introducing the Motherboard
2
Feature
Processor
The RX480-A uses an 939-pin socket that carries the following features:
•
•
Accommodates AMD Sempron/Athlon64/Athlon 64 FX processors
Supports up to 2000MT/s HyperTransportTM (HT) interface speeds
HyperTransportTM Technology is a point-to-point link between two devices, it enables
integrated circuits to exchange information at much higher speeds than currently
available interconnect technologies.
Chipset
The RX480 Northbridge (NB) and SB400 Southbridge (SB) chipsets are based on an
innovative and scalable architecture with proven reliability and performance.
RX480 (NB)
•
•
•
•
SB400 (SB)
•
•
•
•
•
Memory
•
•
1 x 2 (expandable to x 4) A-Link Express interface (PCI
Express 1.0a compliant) for connection to the ATI IXP
Supports one PCI Express x16 for Graphics Interface, fully
compliant to the PCI Express Base Specification revision
1.0a.
Fully supports ACPI states S1, S3, S4 and S5.
Supports Single chip solution in 0.13 micron, 1.0-1.2v CMOS
technology
2/4-lane A-Link Express interface (PCI Express 1.0a compliant) to RADEON IGPs
Compliant with PCI 2.3 specificaiton, up to 7 bus master
devices supported
Four Serial ATA devices supported, compliant with Serial
ATA 1.0 specification, RAID 0 and RAID 1 accommodated
Integrated USB 2.0 Host Controller supporting up to eight
USB 2.0 ports
Integrated IDE controller supports Ultra DMA 133/100/66/33
modes
DDR 400/333/266 DDR SDRAM with Dual Channel supported
Accommodates four unbuffered DIMMs, up to 4GB maximum memory size
Audio (optional)
This motherboard may support either of the following Audio chipset.
•
•
•
•
•
•
•
Compliant with the AC’97 v2.3 specification
16-bit Stereo full-duplex CODEC with 48KHz sampling rate
Supports double sampling rate (96KHz) of DVD audio playback
Direct Sound 3D™ compatible
Compliant with AC’97 2.3 specification, supporting 8-ch DACs
Meets performance requirements for audio on PC99/2001 systems
Meets Microsoft WHQL/WLP 2.0 audio requirements
Introducing the Motherboard
3
Onboard LAN (Optional)
This motherboard may support either of the following LAN with following features:
•
•
•
•
•
•
•
•
Support 10/100 Mbps N-way Auto-negotiation operation
Supports Wake-On-LAN function and remote wake-up
Supports LED pins for various network activity indications
Supports Full Duplex Flow Control (IEEE 802.3x)
Integrated 10/100/1000 transceiver
Supports PCI rev. 2.3, 32-bit, 33/66MHz
Crossover Detection & Auto-Correction
Wake-on-LAN and remote wake-up support
1394a FireWire (Optional)
•
•
Fully compliant with provisions of IEEE Std 1394-1995 for a high-performance
serial bus and IEEE Std 1394a-2000
Two IEEE Std 1394a-2000 fully compliant cable ports at 100M/200M400M bits/
s
Expansion Options
The motherboard comes with the following expansion options:
•
•
•
•
•
•
One PCI Express x16 for Graphic Interface
Two PCI Express x1 slots
Three 32-bit PCI v2.3 compliant slots
Two 40-pin IDE connectors supporting up to 4 IDE devices
One floppy disk drive interface
Four 7-pin SATA connectors
The motherboard supports UltraDMA bus mastering with transfer rates of 133/100/66/
33 MB/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
•
Two PS/2 ports for mouse and keyboard
•
One serial port
•
One parallel port
•
Four USB ports
•
One 1394a port (optional)
•
One LAN port (optional)
•
Audio jacks for microphone in, line-in and 8-ch Audio output
BIOS Firmware
This motherboard uses AWARD BIOS that enables users to configure many system
features including the following:
•
•
•
•
Power management
Wake-up alarms
CPU parameters
CPU and memroy timing
The firmware can also be used to set parameters for different processor clock speeds.
Some hardware specifications and software items are subject to change
with out prior notice.
Introducing the Motherboard
4
Motherboard Components
Introducing the Motherboard
5
Table of Motherboard Components
1
2
3
4
5
6
LABEL
CPU Socket
CPU_FAN
DIMM1~4
ATX_POWER
CLR_CMOS
PWR_FAN*
COMPONENT
Socket 939 for AMD K8 processor
CPU cooling fan connector
184-pin DDR SDRAM slots
Standard 24-pin ATX power connector
Clear CMOS jumper
Power fan connector
7 IDE2
8 IDE1
Secondary IDE channel
Primary IDE channel
9 FDD
10
11
12
13
14
15
Floppy diskette drive connector
PANEL1
SATA1~4
J1
USB3-4
PCI1~3
IR1*
Front panel switch/LED header
Serial ATA connectors
Speaker header
Front Panel USB headers
32-bit add-on card slots
Infrared header
16 BIOS_WP
17 SPDIFO2
BIOS protection jumper
SPDIF out header
18
19
20
21
22
23
Analog audio input connector
Front panel audio header
PCI Express x1 slots
PCI Express x16 graphics card slot
4-pin +12V power connector
System cooling fan connector
CD_IN1
AUDIO2
PCI-E1~2
PCIEX16
ATX12V
SYS_FAN*
“*” stands for optional components.
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
6
Memo
Introducing the Motherboard
7
Chapter 2
Installing the Motherboard
Safety Precautions
•
•
•
•
•
Follow these safety precautions when installing the motherboard
Wear a grounding strap attached to a grounded device to avoid damage from
static electricity
Discharge static electricity by touching the metal case of a safely grounded
object before working on the motherboard
Leave components in the static-proof bags they came in
Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies with
the specifications for the micro ATX system case. First, some features on the motherboard
are implemented by cabling connectors on the motherboard to indicators and switches on
the system case. Make sure that your case supports all the features required. Secondly,
RX480-A supports one or two floppy diskette drives and four enhanced IDE drives. Make
sure that your case has sufficient power and space for all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the motherboard.
This motherboard carries a micro ATX form factor of 304 x 225 mm. Choose a case that
accommodates this form factor.
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in a case.
Most system cases have mounting brackets installed in the case, which correspond the holes
in the motherboard. Place the motherboard over the mounting brackets and secure the
motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion slots
on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than
one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on
the correct pins.
The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.
SHORT
This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT
Installing the Motherboard
OPEN
9
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
Jumper Settings
Jumper
Type
Description
Setting (default)
1-2: CLEAR
2-3: NORMAL
CLR_CMOS 3-pin
Before clearing the
CMOS, make sure to
turn off the system.
BIOS_WP
2-pin
CLR_CMOS
CLEAR CMOS
OPEN: DISABLE
1
BIOS_WP
BIOS PROTECT
SHORT: ENABLE
Installing the Motherboard
1
10
Connecting Case Components
After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:
1
2
3
4
5
6
7
Connect the CPU cooling fan cable to CPU_FAN.
Connect the system cooling fan connector to SYS_FAN.
Connect the power fan connector to PWR_FAN.
Connect the case speaker cable to J1.
Connect the case switches and indicator LEDs to the PANEL1.
Connect the standard power supply connector to ATX_POWER.
Connect the auxiliary case power supply connector to ATX12V.
Connecting 20/24-pin power cable
Users please note that the 20-pin and 24-pin power cables can both be connected to the ATX1 connector. With the 20-pin power cable, just align the 20pin power cable with the pin 1 of the ATX1 connector. However, using 20-pin
power cable may cause the system to become unbootable or unstable because of
insufficient electricity. A minimum power of 300W is recommended for a
fully-configured system.
With ATX v1.x power supply, users please
note that when installing 20-pin power cable,
the latche of power cable clings to the left
side of the ATX_POWER connector latch,
just as the picture shows.
20-pin power cable
With ATX v2.x power supply, users please
note that when installing 24-pin power cable,
the latches of power cable clings to the right
side of the ATX_POWER connector latch.
24-pin power cable
Installing the Motherboard
11
CPU_FAN/SYS_FAN/PWR_FAN: FAN Power Connectors
Pin
1
2
3
Signal Name
GND
+12V
FAN_TAC
Function
System Ground
Power +12V
Sensor
J1: Internal Speaker
Pin
1
2
3
4
Signal Name
VCC
Key
NC
Signal
ATX12V: ATX 12V Power Connector
Pin
1
2
3
4
Signal Name
Ground
Ground
+12V
+12V
ATX_POWER: ATX 24-pin Power Connector
Pin
Signal Name
1
2
3
4
5
6
7
8
9
+3.3V
10
11
12
+12V
+3.3V
Ground
+5V
Ground
+5V
Ground
PWRGD
+5VSB
+12V
+3.3V
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Signal Name
+3.3V
-12V
GND
PS_ON
GND
GND
GND
-5V
+5V
+5V
+5V
GND
Installing the Motherboard
12
Front Panel Header
The front panel header (PANEL1) provides a standard set of switch and LED headers
commonly found on ATX or micro ATX cases. Refer to the table below for information:
Pin
Signal
Function
Pin
Signal
Function
1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)
3
HD_LED_N Hard disk LED(-)
5
RST_SW_N Reset Switch(-)
4
6
FP PWR/SLP *MSG LED(-)
PWR_SW_P Power Switch(+)
7
RST_SW_P
Reset Switch(+)
8
PWR_SW_N Power Switch(-)
9
RSVD
Reserved
10 Key
No pin
* MSG LED (dual color or single color)
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data
is being read from or written to the hard drive. For the LED to function properly, an IDE
drive should be connected to the onboard IDE interface. The LED will also show activity
for devices connected to the SATA (hard drive activity LED) connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power
on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact
switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms
to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before
the power supply recognizes another on/off signal.
Installing the Motherboard
13
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount
resistors with the clip of the cooling fan. If the clip of the cooling fan
scrapes across the motherboard, you may cause serious damage to the
motherboard or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change these settings by making changes
to jumpers on the motherboard, or changing the settings in the system Setup Utility. We
strongly recommend that you do not over-clock processors or other components to run
faster than their rated speed.
Warning: Over-clocking components can adversely affect the reliability
of the system and introduce errors into your system. Over-clocking can
permanently damage the motherboard by generating excess heat in
components that are run beyond the rated limits.
This motherboard has a Socket 939 porcessor socket. When choosing a processor, consider
the performance requirements of the system. Performance is based on the processor design,
the clock speed and system bus frequency of the processor, and the quantity of internal
cache memory and external cache memory.
Installing the Motherboard
14
CPU Installation Procedure
The following illustration shows CPU installation components.
1
2
3
4
5
Install your CPU. Pull up the lever away from the
socket and lift up to 90-degree angle.
Locate the CPU cut edge (the corner with the pin
hold noticeably missing). Align and insert the CPU
correctly.
Press the lever down and apply thermal grease on
top of the CPU.
Put the CPU Fan down on the retention module and
snap the four retention legs of the cooling fan into
place.
Flip the levers over to lock the heat sink in place and
connect the CPU cooling Fan power cable to the
CPUFAN connector. This completes the installation.
To achieve better airflow rates and heat dissipation, we suggest that you use
a high quality fan with 4800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The
form and size of fan/heatsink may also vary.
Installing the Motherboard
15
Installing Memory Modules
This motherboard accomodates four memory modules. It can support four 184-pin 2.5V
unbuffered DIMM, DDR 400/333/266. The maximum memory capacity is 4GB. You must
install at least one module in any of the two slots. Each module can be installed with 256MB
to 1GB of memory.
DDR SDRAM memory module table
Memory module
DDR 266
DDR 333
DDR 400
Memory Bus
133MHz
166MHz
200MHz
Do not remove any memory module from its antistatic packaging until you
are ready to install it on the motherboard. Handle the modules only by
their edges. Do not touch the components or metal parts. Always wear a
grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1
2
3
4
5
6
This motherboard supports unbuffered DDR SDRAM .
Push the latches on each side of the DIMM slot down.
Align the memory module with the slot. The DIMM slots are keyed with notches
and the DIMMs are keyed with cutouts so that they can only be installed
correctly.
Check that the cutouts on the DIMM module edge connector match the notches
in the DIMM slot.
Install the DIMM module into the slot and press it firmly down until it seats
correctly. The slot latches are levered upwards and latch on to the edges of
the DIMM.
Install any remaining DIMM modules.
Installing the Motherboard
16
Table A: Unbuffered DIMM Support for 939-pin
Maximum
DRAM Speed
Chip Selects
Data
Bus
MEMCS_1L_L* MEMCS_1H_L* MEMCS_2L_L* MEMCS_2H_L*
64bits
128bits
1T
2T
Single rank
N/A
N/A
N/A
DDR400 DDR400
Double rank
N/A
N/A
N/A
DDR400 DDR400
N/A
N/A
Single rank
N/A
DDR400 DDR400
N/A
N/A
Double rank
N/A
DDR400 DDR400
Single rank
N/A
Single rank
N/A
DDR333 DDR400
Single rank
N/A
Double rank
N/A
DDR200 DDR400
Double rank
N/A
Single rank
N/A
DDR200 DDR400
Double rank
N/A
Double rank
N/A
DDR200 DDR333
DDR400 DDR400
Single rank
Single rank
N/A
N/A
Double rank
Double rank
N/A
N/A
DDR400 DDR400
N/A
N/A
Single rank
Single rank
DDR400 DDR400
N/A
N/A
Double rank
Double rank
DDR400 DDR400
Single rank
Single rank
Single rank
Single rank
DDR333 DDR400
Single rank
Single rank
Double rank
Double rank
DDR200 DDR400
Double rank
Double rank
Single rank
Single rank
DDR200 DDR400
Double rank
Double rank
Double rank
Double rank
DDR200 DDR333
Note for “*”: Memory types must be set to values consistent with system hardware.
Table B: DDR(memory module) QVL (Qualified Vendor List)
The following DDR400 memory modules have been tested and qualified for use with this
motherboard.
Size Vendor
128MB
Module Name
NANYA
NT128D64SH4B1G-5
Infineon
NANYA
HYS64D16301GU-5-B
NT128D64SH4B1G-5T
256MB
Micron
Infineon
SAMSUNG
NANYA
Infineon
Kingston
Micron
MT16VDDT3264AG-403B2
HYS64D32300GU-5-B
M368L3223DTM-CC4
NT256D64S88B1G-5T
HYS64D32300HU-5-C
KVR400X64C3A
MT8VDDT3264AG-40BC4
512MB
NANYA
Infineon
NT512D64S8HB1G-5T
HYS64D64320HU-5-C
Installing the Motherboard
17
Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive
This section describes how to install IDE devices such as a hard disk drive and a CD-ROM
drive.
About IDE Devices
Your motherboard has two IDE channel interfaces (IDE1 & IDE2). Two IDE ribbon cables
supporting four IDE devices is bundled with the motherboard.
You must orient the cable connector so that the pin1 (color) edge of the
cable correspoinds to the pin 1 of the I/O port connector.
IDE1: Primary IDE Connector
The first hard drive should always be connected to IDE1.
IDE2: Secondary IDE Connector
The second drive on this controller must be set to slave mode. The cinfiguration is the same
as IDE1.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE.
Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that
one device is set to MASTER and the other device is set to SLAVE. The documentation of
your IDE device explains how to do this.
Installing the Motherboard
18
About SATA Connectors
This motherboard features four SATA connectors supporting a total of four drives. SATA ,
or Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE
hard drives which are currently used in most PCs. These connectors are well designed and
will only fit in one orientation. Locate the SATA connectors on the motherboard and follow
the illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial
ATA protocol. This SATA cable comes with an SATA power cable. You can connect either
end of the SATA cable to the SATA hard drive or the connector on the motherboard.
SATA cable
Refer to
1
2
3
(optional)
SATA power cable
(optional)
the illustration below for proper installation:
Attach either cable end to the connector on the motherboard.
Attach the other cable end to the SATA hard drive.
Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
This motherboard does not support the “Hot-Plug” function.
Installing the Motherboard
19
Installing a Floppy Diskette Drive
The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive
ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch
drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one
type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
You must orient the cable connector so that the pin 1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.
FDD: Floppy Disk Connector
This connector supports the provided floppy drive ribbon cable. After connecting the single
end to the onboard floppy connector, connect the remaining plugs on the other end to the
floppy drives correspondingly.
Installing the Motherboard
20
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the
system bus. Expansion slots are a means of adding or enhancing the motherboard’s features
and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
PCIEX16
Slot
The PCI Express x16 slot is used to install an external PCI Express graphics
card that is fully compliant to the PCI Express Base Specification revision
1.0a.
PCI-E1~2
(PCI-Ex1
Slots)
The two PCI Express x1 slots are fully compliant to the PCI Express Base
Specification revision 1.0a as well.
PCI 1~3
Slots
This motherboard is equipped with three standard PCI slots. PCI stands for
Peripheral Component Interconnect and is a bus standard for expansion
cards, which for the most part, is a supplement of the older ISA bus standard.
The PCI slots on this board are PCI v2.3 compliant.
1.Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.
2.Some PCI-E x16 graphics cards may be so bulky that it could block one
PCI-E x1 slot.
3.Please pull out the PCI-Ex16 graphics card straightway to remove it
when you want to uninstall it.
Installing the Motherboard
21
Follow these instructions to install an add-on card:
1
2
3
Remove a blanking plate from the system case corresponding to the slot you
are going to use.
Install the edge connector of the add-on card into the expansion slot. Ensure
that the edge connector is correctly seated in the slot.
Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the
add-on card.
Installing the Motherboard
22
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
AUDIO2: Front Panel Audio header
This header allows the user to install auxiliary front-oriented microphone and line-out ports
for easier access.
Pin
Pin
Signal Name
Signal Name
Function
1
2
3
4
5
6
7
AUD_MIC
Front Panel Microphone input signal
AUD_GND
Ground used by Analog Audio Circuits
8
9
10
Key
No Pin
AUD_F_L
Left Channel Audio signal to Front Panel
AUD_RET_L
Left Channel Audio signal to Return from Front Panel
AUD_MIC_BIAS Microphone Power
AUD_VCC
Filtered +5V used by Analog Audio Circuits
AUD_F_R
Right Channel audio signal to Front Panel
AUD_RET_R
RightChannelAudiosignaltoReturnfromFrontPanel
REVD
Reserved
Installing the Motherboard
23
IR1: Infrared header
The motherboard supports an Infrared (IR1) data port. Infrared ports allow the wireless
exchange of information between your computer and similarly equipped devices such as
printers, laptops, Personal Digital Assistants (PDAs), and other computers.
Pin
1
2
3
4
5
6
Signal Name
RSVD
No Pin
IR Power, +5V
Ground
IR_Tx
IR_Rx
SATA1/2/3/4: Serial ATA connectors
These connectors are use to support the new Serial ATA devices for the highest date transfer
rates (150 MB/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations
of the current Parallel ATA interface. But maintains register compatibility and software
compatibility with Parallel ATA.
Pin
Pin
1
3
5
7
Signal Name
Signal Name
Ground
Pin
2
4
6
-
TXRXGround
Signal Name
Function
TX+
Ground
RX+
-
SPDIFO2: SPDIF out header
This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output
to digital multimedia device through optical fiber or coxial connector.
Pin
Pin
1
2
3
4
Signal Name
Signal Name
SPDIF
VCC
Key
GND
Function
Function
SPDIF digital output
5V analog power
No pin
Ground
CD_IN1: Analog audio input connector
Pin
1
2
3
4
Signal Name
CDL
CDG
CDG
CDR
Function
Left CD-in signal
CD-in ground
CD-in ground
Right CD-in signal
Installing the Motherboard
24
USB3/4: Front Panel USB header
The motherboard has four USB ports installed on the rear edge I/O port array. Additionally,
there are two USB headers onboard. Use the auxiliary USB headers to connect the frontmounted ports to the motherboard.
Pin
Signal Name
Function
1
2
3
4
5
6
7
USBPWR
Front Panel USB Power
USBPWR
Front Panel USB Power
USB_FP_P0-
USB Port 0 Negative Signal
USB_FP_P1-
USB Port 1 Negative Signal
USB_FP_P0+
USB Port 0 Positive Signal
USB_FP_P1+
USB Port 1 Positive Signal
GND
Ground
8
9
10
GND
Ground
Key
No pin
USB_FP_OC0
Overcurrent signal
Installing the Motherboard
25
Connecting I/O Devices
The backplane of the motherboard has the following I/O ports:
PS2 Mouse
Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard
Use the lower PS/2 port to connect a PS/2 keyboard.
Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications
devices.
Serial Port
(COM1)
Use the COM port to connect serial devices such as mice or
fax/modems. COM1 is identified by the system as COM1/3.
LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your computer
to the Network.
USB Ports
Use the USB ports to connect USB devices.
Audio Ports
Use the audio jacks to connect audio devices. The D port is for
stereo line-in signal, while the F port is for microphone in signal.
This motherboard supports 8-channel audio devices that correspond to the A, B, C, and E port respectively. In addition, all of the
3 ports, B, C, and E provide users with both right & left channels
individually. Users please refer to the following note for specific
port function definition.
A: Center & Woofer
B: Back Surround
C: Side Surround
D: Line-in
E: Front Out
F: Mic_in Rear
The above port definition can be changed to audio input or
audio output by changing the driver utility setting.
This concludes Chapter 2. The next chapter covers the BIOS.
Installing the Motherboard
26
Memo
Installing the Motherboard
27
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest Award BIOS with support for Windows Plug and Play. The
CMOS chip on the motherboard contains the ROM setup instructions for configuring the
motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are
stored in battery-backed-up CMOS RAM that saves this information when the power is
turned off. When the system is turned back on, the system is configured with the values you
stored in CMOS.
The BIOS Setup Utility enables you to configure:
•
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
Password protection from unauthorized use
•
Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the
Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend
that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
•
•
•
•
•
when changing the system configuration
when a configuration error is detected and you are prompted to make changes
to the Setup Utility
when trying to resolve IRQ conflicts
when making changes to the Power Management configuration
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines.
POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are
completed, the following message appears:
Using BIOS
28
Press DEL to enter SETUP
Pressing the delete key accesses the BIOS Setup Utility:
Phoenix-AwardBIOS CMOS Setup Utility:
Standard CMOS Features
Advanced BIOS Features
Frequency/Voltage Control
Load Performance Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
Exit Without Saving
Esc: Quit
F10: Save & Exit Setup
: Select Item
Time, Date, Hard Disk Type...
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY
FUNCTION
Move
Enter
+/-/PU/PD
Select
Value
ESC
Exits the current menu
F1
General Help
F2
Item Help
F5
Previous Values
F6
F7
Fail-Safe Defaults
Optimized Defaults
F10
Save
Using BIOS
29
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s
Web site. New BIOS provides support for new peripherals, improvements in performance,
or fixes for known bugs. Install new BIOS as follows:
1
2
3
4
5
6
7
8
If your motherboard has a BIOS protection jumper, change the setting to allow
BIOS flashing.
If your motherboard has an item called Firmware Write Protect in Advanced
BIOS features, disable it. (Firmware Write Protect prevents BIOS from being
overwritten.
Create a bootable system disk. (Refer to Windows online help for information
on creating a bootable system disk.)
Download the Flash Utility and new BIOS file from the manufacturer’s Web
site. Copy these files to the system diskette you created in Step 3.
Turn off your computer and insert the system diskette in your
computer’s diskette drive. (You might need to run the Setup Utility and change
the boot priority items on the Advanced BIOS Features Setup page, to force
your computer to boot from the floppy diskette drive first.)
At the A:\ prompt, type the Flash Utility program name and press <Enter>.
Type the filename of the new BIOS in the “File Name to Program” text box.
Follow the onscreen directions to update the motherboard BIOS.
When the installation is complete, remove the floppy diskette from the diskette
drive and restart your computer. If your motherboard has a Flash BIOS jumper,
reset the jumper to protect the newly installed BIOS from being overwritten.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup
Utility displays a list of the options that are available. A highlight indicates which option is
currently selected. Use the cursor arrow keys to move the highlight to other options. When
an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for information.
Some options (marked with a triangle ) lead to submenus that enable you to change the
values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a
triangle .
Using BIOS
30
Standard CMOS Features
This option displays basic information about your system.
Phoenix-AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy) Wed, Mar 29 2005
Time (hh:mm:ss)
9 : 33 : 26
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
Drive A
Drive B
Floppy 3 Mode Support
[1.44M, 3.5 in.]
[None]
[Disabled]
Video
Halt On
[EGA/VGA]
[All Errors]
Base Memory
Extended Memory
Total Memory
640K
65535K
1024K
Item Help
Menu Level
Change the day, month,
year and century
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Date and Time
The Date and Time items show the current date and time on the computer. If
you are running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
IDE Devices (None)
Your computer has two IDE channels (Primary and Secondary) and each channel can be
installed with one or two devices (Master and Slave). Use these items to
configure each device on the IDE channel.
Press <Enter> to display the IDE submenu:
Phoenix-AwardBIOS CMOS Setup Utility
IDE Channel 0 Slave
IDE HDD Auto-Detection
[Press Enter]
IDE Channel 0 Slave
Access Mode
[Auto]
[Auto]
Capacity
0MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
Item Help
Menu Level
To auto-detect the
HDD’s size, head... on
this channel
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
IDE HDD Auto-Detection
Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically
detect and configure an IDE device on the IDE channel.
Using BIOS
31
If you are setting up a new hard disk drive that supports LBA mode, more
than one line will appear in the parameter box. Choose the line that lists
LBA for an LBA drive.
IDE Channel 0/1 Master/Slave (Auto)
Leave this item at Auto to enable the system to automatically detect and configure IDE
devices on the channel. If it fails to find a device, change the value to Manual and then
manually configure the drive by entering the characteristics of the drive in the items
described below.
Refer to your drive’s documentation or look on the drive casing if you need to obtain
this information. If no device is installed, change the value to None.
Before attempting to configure a hard disk drive, ensure that you have the
configuration information supplied by the manufacturer of your hard drive.
Incorrect settings can result in your system not recognizing the installed hard
disk.
Access Mode (Auto)
This item defines ways that can be used to access IDE hard disks such as LBA (Large
Block Addressing). Leave this value at Auto and the system will automatically decide the
fastest way to access the hard disk drive. If you choose IDE Channel 2/3 Master, the
item only have Large and Auto.
Press <Esc> to return to the Standard CMOS Features page.
Drive A/Drive B (1.44M, 3.5 in./None)
These items define the characteristics of any diskette drive attached to the system.
You can connect one or two diskette drives.
Floppy 3 Mode Support (Disabled)
Floppy 3 mode refers to a 3.5-inch diskette with a capacity of 1.2 MB. Floppy 3
mode is sometimes used in Japan.
Video (EGA/VGA)
This item defines the video mode of the system. This motherboard has a built-in VGA
graphics system; you must leave this item at the default value.
Halt On (All Errors)
This item defines the operation of the system POST (Power On Self Test) routine. You
can use this item to select which types of errors in the POST are sufficient to halt the
system.
Base Memory, Extended Memory, and Total Memory
These items are automatically detected by the system at start up time. These are
display-only fields. You cannot make changes to these fields.
Using BIOS
32
Advanced BIOS Features
This option defines advanced information about your system.
Phoenix-AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Hard Disk Boot Priority
CPU Internal Cache
External Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
ATA 66/100 IDE Cable Msg.
Typematic Rate Setting
X Typematic Rate (Chars/Sec0
X Typematic Delay (Msec)
Security Option
APIC Mode
OS Select For DRAM>64MB
[Press Enter]
[Enabled]
[Enabled]
[Enabled]
[Floppy]
[Hard Disk]
[CDROM]
[Enabled]
[Disabled]
[Disabled]
[On]
[Fast]
[Enabled]
[Disabled]
6
250
12
12
[Setup]
12
12
[Enabled]
[Non-OS2]
Item Help
Menu Level
Select Hard Disk
Boot Device Priority
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Hard Disk Boot Priority (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
1. Pri.Master:
2. Pri.Slave:
3. Sec. Master:
4. Sec. Slave:
5. USBHDD0:
6. USBHDD1:
7. USBHDD2:
8. Bootable Add-in Cards
: Move
Item Help
Menu Level
Use <
> or <
>
to select a device, then
press <+> to move it
up, or <-> to move it
down the list. Press
<ESC> to exit this
menu.
PU/PD+/-/:Change Priority F10:Save ESC:Exit
CPU Internal Cache (Enabled)
All processors that can be installed in this motherboard use internal level 1 (L1) cache
memory to improve performance. Leave this item at the default value for better performance.
External Cache (Enabled)
Most processors that can be installed in this system use external level 2 (L2) cache memory
to improve performance. Leave this item at the default value for better performance.
Quick Power On Self Test (Enabled)
Enable this item to shorten the power on testing (POST) and have your system start
up faster. You might like to enable this item after you are confident that your system
hardware is operating smoothly.
Using BIOS
33
First/Second/Third Boot Device (Floppy/Hard Disk/CDROM)
Use these three items to select the priority and order of the devices that your system
searches for an operating system at start-up time.
Boot Other Device (Enabled)
When enabled, the system searches all other possible locations for an operating system if
it fails to find one in the devices specified under the First, Second, and Third boot devices.
Swap Floppy Drive (Disabled)
If you have two floppy diskette drives in your system, this item allows you to swap the
assigned drive letters so that drive A becomes drive B, and drive B becomes drive A.
Boot Up Floppy Seek (Disabled)
If this item is enabled, it checks the size of the floppy disk drives at start-up time. You
don’t need to enable this item unless you have a legacy diskette drive with 360K capacity.
Boot Up NumLock Status (On)
This item defines if the keyboard Num Lock key is active when your system is started.
Gate A20 Option (Fast)
This item defines how the system handles legacy software that was written for an earlier
generation of processors. Leave this item at the default value.
ATA 66/100 IDE Cable Msg. (Enabled)
This item enables or disables the display of the ATA 66/100 Cable MSG.
Typematic Rate Setting (Disabled)
If this item is enabled, you can use the following two items to set the typematic rate and the
typematic delay settings for your keyboard.
•
Typematic Rate (Chars/Sec): Use this item to define how many characters
per second are generated by a held-down key.
•
Typematic Delay (Msec): Use this item to define how many milliseconds
must elapse before a held-down key begins generating repeat characters.
Security Option (Setup)
If you have installed password protection, this item defines if the password is required at
system start up, or if it is only required when a user tries to enter the Setup Utility.
APIC Mode (Enabled)
This item allows you to enable or disable the APIC (Advanced Programmable Interrupt
Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing
support for up to 60 processors.
OS Select For DRAM > 64 MB (Non-OS2)
This item is only required if you have installed more than 64 MB of memory and you are
running the OS/2 operating system. Otherwise, leave this item at the default.
HDD S.M.A.R.T Capability (Disabled)
The S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system is a
diagnostics technology that monitors and predicts device performance S.M.A.R.T.
software resides on both the disk drive and the host computer.
Using BIOS
34
The disk drive software monitors the internal performance of the motors, media, heads
and electronics of the drive. The host software monitors the overall reliability status of
the drive. If a device failure is predicted, the host software, through the Client WORKS
S.M.A.R.T applet, warns the user of the impending condition and advises appropriate
action to protect the data.
Full Screen LOGO Show (Enabled)
When enabled, this will show a full screen company logo on the boot up screen. Select
disabled when you want to show POST messages during boot up.
Small Logo (EPA) Show (Disabled)
Enables or disables the display of the EPA logo during boot.
BIOS Rom TBL protect (Disabled)
This item enables or disables the BIOS Bootblock protect.
Advanced Chipset Features
These items define critical timing parameters of the motherboard. You should leave the
items on this page at their default values unless you are very familiar with the technical
specifications of your system hardware. If you change the values incorrectly, you may
introduce fatal errors or recurring instability into your system.
Phoenix-AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Configuration
LDT & PCI Bus Control
Video RAM Cacheable
System BIOS Cacheable
Item Help
[Press Enter]
[Press Enter]
[Enabled]
[Enabled]
Menu Level
DRAM timing and
control
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
DRAM Configuration(Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
DRAM Configuration
Timing Mode
Memclock index value (MHz)
CAS# latency (Tcl)
Min RAS# active time (Tras)
RAS# to CAS# delay (Trcd)
Row precharge Time (Trp)
Row to Row delay(Trrd)
Row cycle time (Trc)
Row refresh cyc time(Trfc)
User Config mode
X 1T/2T Memory Timing
X Read Preamble value
X Async Latency value
X
X
X
X
X
X
X
X
[Auto]
200Mhz
2.5
8T
4T
4T
2T
12T
24T
[Auto]
2T
6.5ns
5ns
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Using BIOS
35
Timing Mode (Auto)
This item allows you to set up the DRAM timing manually or automatically. This item
is set to [Auto] by default. When setting to [Manua], the following items are adjustable.
•
Memclock index value (Mhz) (200MHz): When DDR Timing Setting by is
set to Manual, use this item to set the DRAM frequency.
•
CAS# latency (Tcl) (2.5): This item determines the operation of SDRAM
memory CAS (column address strobe). It is recommended that you leave this
item at the default value. The 2T setting requires faster memory that specifically supports this mode.
•
Min RAS# to active time (Tras) This item determines the time RAS takes to
read from and write to a memory cell.
•
RAS to CAS Delay (Trcd) (4T): This is the amount of time a CAS is performed after a RAS. The lower the better, but some DRAM does not support
low figures.
•
Row precharge Time (Trrd) (2T) This item specifies the Row precharge to
Active or Auto-Refresh of the same bank.
•
Row to Row delay (Trrd) (2T) This item specifies the active-to-active delay
of different banks.
•
Row cycle time (Trc) (12T) This item determines the minumum number of
clock cycles a memory row takes to complete a full cycle, from row activation
up to the precharging of the active row.
•
Row refresh cyc time (Trfc) (24T) Auto-refreshactive to RAS#-active or
RAS# auto-refresh.
User Config mode (Auto)
This item has the capacity to automatically detect all of the following fields default
values. This item is set to [Auto] by default. When setting to [Manua], the following
items are adjustable.
•
1T/2T Memory Timing (2T) This item controls the SDRAM command rate.
•
Read Preamble value (6.5ns) This item allows you to set Read Preamble
value from 2ns, to 9.5ns, and it is specified in units of 0.5ns.
•
Async Latency value (5ns) This item allows you to set Async Latency
value from 2ns to 11ns, and it is specified in units of 1 ns.
Press <Esc> to return to the Advanced Chipset Features page.
LDT & PCI Bus Control (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Advanced Chipset Features
LDT Configuration
Upstream LDT Bus Width
Downstream LDT Bus Width
LDT Bus Frequency
PCIE Reset Delay
[Enabled]
[16 bit]
[16 bit]
[Auto]
[Disabled]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Using BIOS
36
LDT Configuration (Enabled)
This item enables or disables the LDT configuration.
Upstream LDT Bus Width (16 bit)
This item allows users to manually adjust the upstream LDT bus width to be 8 bit or 16
bit.
Downstream LDT Bus Width (16 bit)
This item allows users to manually adjust the downstream LDT bus width to be 8 bit or
16 bit.
LDT Bus Frequency (Auto)
This item allows users to manually adjust the LDT Bus Frequency.
PCIE Reset Delay (Disabled)
This item enables or disables the PCIE reset delay.
Press <Esc> to return to the Advanced Chipset Features page.
Video RAM Cacheable (Enabled)
This item allows users to enable or disable the video ram cacheable function.
System BIOS Cacheable (Enabled)
This feature is only valid when the system BIOS is shadowed. It enables or disables the
caching of the system BIOS ROM at F0000h-FFFFFh via the L2 cache. This greatly
speeds up accesses to the system BIOS.
Integrated Peripherals
These options display items that define the operation of peripheral components on
the system’s input/output ports.
Phoenix-AwardBIOS CMOS Setup Utility
Integrated Peripherals
South OnChip IDE Device
South OnChip PCI Device
SuperIO Device
Init Display First
[Press Enter]
[Press Enter]
[Press Enter]
[PCI Slot]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Using BIOS
37
South OnChip IDE Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
SIS OnChip IDE Device
IDE DMA transfer access
Onchip IDE Channel0
Onchip IDE Channel1
IDE Prefetch Mode
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master UDMA
Primary Slave UDMA
Secondary Master UDMA
Secondary Slave UDMA
IDE HDD Block mode
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
IDE DMA transfer access (Enabled)
This item allows you to enable the transfer access of the IDE DMA then burst onto the
PCI bus and nonburstable transactions do not.
OnChip IDE Channel0/1 (Enabled)
Use this item to enable or disable the PCI IDE channels that are integrated on the
motherboard.
IDE Prefetch Mode (Enabled)
The onboard IDE drive interface supports IDE prefetching, for faster drive access. If you
install a primary and secondary add-on interface, set this field to Disable if the interface
does not support prefetching.
Primary/Secondary Master/Slave PIO (Auto)
Each IDE channel supports a master device and a slave device. These four items let you
assign the kind of PIO (Programmed Input/Output) was used by the IDE devices. Choose
Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 04.
Primary/Secondary Master/Slave UDMA (Auto)
Each IDE channel supports a master device and a slave device. This motherboard
supports UltraDMA technology, which provides faster access to IDE devices.
If you install a device that supports UltraDMA, change the appropriate item on this list
to Auto. You may have to install the UltraDMA driver supplied with this motherboard in
order to use an UltraDMA device.
IDE HDD Block Mode (Enabled)
Enable this field if your IDE hard drive supports block mode. Block mode enables BIOS
to automatically detect the optimal number of block read and writes per sector that the
drive can support. It also improves the speed of access to IDE devices.
Press <Esc> to return to the Integrated Peripherals page.
Using BIOS
38
South OnChip PCI Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
SIS OnChip PCI Device
Onboard AC97 AUDIO
Onboard PCI Lan
Onboard Lan Boot ROM
Onboard 1394
Serial ATA Controller
USB 2.0 Supports
USB Controller
USB Legacy Support
USB Mouse Support
[Auto]
[Enabled]
[Disabled]
[Enabled]
[IDE Mode]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Onboard AC’ 97 AUDIO (Auto)
This option allows you to control the onboard AC’ 97 audio. Disable this item if you are
going to install a PCI audio add-on card.
Onboard PCI LAN (Enabled)
This option allows you to control the onboard LAN device.
Onboard LAN Boot ROM (Disabled)
Use this item to enable and disable the booting from the onboard LAN or a network addin card with a remote boot ROM installed.
Onboard 1394 (Enabled)
This option allows you to enable or disable the onboard 1394 function.
SATA Controller (IDE Mode)
This item allows you to controller Serial ATA controller.
USB 2.0 Supports (Enabled)
Enable this item if your system supports USB 2.0.
USB Controller (Enabled)
This item enables the USB controller. Leave this at the default “Enabled” if you want to
connect USB devices to your computer.
USB Legacy Support (Enabled)
Use this item to enable or disable support for legacy USB devices. Setting to Auto allows
the system to detect the presence of USB devices at startup. If detected, the USB
controller legacy mode is enabled. If no USB device is detected, the legacy USB support is
disabled.
USB Mouse Support (Enabled)
Enable this item if you plan to use a mouse connected through the USB port in a legacy
operating system (such as DOS) that does not support Plug and Play.
Press <Esc> to return to the Advanced Chipset Features page.
Using BIOS
39
Onboard SuperIO Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Onboard SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
[Half]
[378/IRQ7]
[ECP]
[3]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Onboard FDC Controller (Enabled)
This option enables the onboard floppy disk drive controller.
Onboard Serial Port 1/2 (3F8/IRQ4) (2F8/IRQ3)
This option is used to assign the I/O address and interrupt request (IRQ) for onboard
serial port 1 (COM1).
UART Mode Select (Normal)
This field is available if the Onboard Serial Port 2 field is set to any option but Disabled.
UART Mode Select enables you to select the infrared communication protocol-Normal
(default), IrDA, or ASKIR.
UR2 Duplex Mode (Half)
This field is available when UART Mode is set to either ASKIR or IrDA. This item
enables you to determine the infrared function of the onboard infrared chip. The options
are Full and Half (default). Full-duplex means that you can transmit and send information simultaneously. Half-duplex is the transmission of data in both directions, but only
one direction at a time.
Onboard Parallel Port (378/IRQ7)
This option is used to assign the I/O address and interrupt request (IRQ) for the onboard
parallel port.
Parallel Port Mode (ECP)
Enables you to set the data transfer protocol for your parallel port. There are four
options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended
Capabilities Port) and ECP+EPP.
ECP Mode Use DMA (3)
When the onboard parallel port is set to ECP mode, the parallel port can use DMA 3 or
DMA 1.
Press <Esc> to return to the Integrated Peripherals page.
Init Display First (PCI Slot)
Use this item to specify whether your graphics adapter is installed in one of the PCI
slots or is integrated on the motherboard.
Using BIOS
40
Power Management Setup
This option lets you control system power management. The system has various powersaving modes including powering down the hard disk, turning off the video, suspending
to RAM, and software power down that allows the system to be automatically resumed
by certain events.
Phoenix-AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Suspend Type
HDD Power Down
Video Off Option
Video Off Method
MODEM Use IRQ
Soft-Off by PWRBTN
PWRON After Pwr-Fail
Resume Event Control
[S3<STR>]
[Disabled]
[Suspend --> Off]
[DPMS Support]
[3]
[Instant-Off]
[Off]
[Press Enter]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
ACPI Suspend Type (S3(STR)
Use this item to define how your system suspends. In the default, S3 (STR), the suspend
mode is a suspend to RAM, i.e., the system shuts down with the exception of a refresh
current to the system memory.
HDD Power Down (Disabled)
The IDE hard drive will spin down if it is not accessed within a specified length of time.
Options are from 1 Min to 15 Min and Disable.
Video Off Option (Suspend—> Off)
This option defines if the video is powered down when the system is put into suspend mode.
Video Off Method (DPMS Support)
This item defines how the video is powered down to save power. This item is set to DPMS
(Display Power Management Software) by default.
MODEM Use IRQ (3)
If you want an incoming call on a modem to automatically resume the system from a powersaving mode, use this item to specify the interrupt request line (IRQ) that is used by the
modem. You might have to connect the fax/modem to the motherboard Wake On Modem
connector for this feature to work.
Soft-Off by PWRBTN (Instant Off)
Under ACPI (Advanced Configuration and Power management Interface) you can create a
software power down. In a software power down, the system can be resumed by Wake Up
Alarms. This item lets you install a software power down that is controlled by the power
button on your system. If the item is set to Instant-Off, then the power button causes a
software power down. If the item is set to Delay 4 Sec. then you have to hold the power
button down for four seconds to cause a software power down.
PWRON After PWR-Fail (Off)
This item enables your computer to automatically restart or return to its operating status.
Using BIOS
41
Resume Event Control (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Resume Event Control
Resume By PCI PME
Resume By USB (S3)
Resume by PCI-E
Resume By WOL/WOM/Ring
Resume By PS2/Mouse
Resume By PS2/Keyboard
KB Resume Password
Hot Key Resume
RTC Alarm Resume
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Enter]
[Ctrl-F1]
[Disabled]
0
0 0 0
Item Help
Menu Level
: Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Resume by PCI PME (Enabled)
This item specifies whether the system will be awakened from power saving modes when
activity or input signal of the specified hardware peripheral or component is detected.
Resume by USB (S3) (Disabled)
This option allows the activity of the USB devices to wake up the system from S3 sleep
state.
Resume by PCI-E (Enabled)
This item specifies whether the system will be awakened from power saving modes when
activity or input signal of the specified hardware peripheral or component is detected.
Resume by WOL/WOM/Ring (Disabled)
This item specifies whether the system will be awakened from power saving modes when
activity or input signal of WOL/WOM/Ring device is detected.
Resume by PS2/Mouse/Keyboard (Disabled)
These items enable or disable you to allow keyboard or mouse activity to awaken the system
from power saving mode.
KB Resume Password (Enter)
Use this item to define the password when using the keyboard to resume the system.
Hot Key Resume (Ctrl-F1)
Use this item to define the password when using the keyboard “hot key” to resume the
system.
RTC Alarm Resume (Disabled)
When set to Enabled, additional fields become available and you can set the date (day of
the month), hour, minute and second to turn on your system. When set to 0 (zero) for
the day of the month, the alarm will power on your system every day at the specified
time.
•
Date of Month: Use this item to define the date of month when using the RTC
alarm to resume the system.
•
Resume Time: Use this item to define the time when using the RTC alarm to
resume the system.
Using BIOS
42
PNP/PCI Configurations
These options configure how PnP (Plug and Play) and PCI expansion cards operate in
your system. Both the the ISA and PCI buses on the motherboard use system IRQs
(Interrup ReQuests) and DMAs (Direct Memory Access). You must set up the IRQ and
DMA assignments correctly through the PnP/PCI Configurations Setup utility for the
motherboard to work properly. Selecting PnP/PCI Configurations on the main program
screen displays this menu:
Phoenix-AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
X
Reset Configuration Data
[Disabled]
Resources Controlled By
IRQ Resources
[Auto(ESCD)]
Press Enter
PCI/VGA Palette Snoop
Assign IRQ For USB
[Disabled]
[Enabled]
Item Help
Menu Level
Default is Disabled. Select
Enabled to reset Extended
System Configuration Data
ESCD) when you exit Setup
if you have installed a new
add-on and the system
reconfiguration has caused
such a serious conflict that
the OS cannot boot
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Reset Configuration Data (Disabled)
If you enable this item and restart the system, any Plug and Play configuration data
stored in the BIOS Setup is cleared from memory.
Resources Controlled By (Auto(ESCD))
You should leave this item at the default Auto (ESCD). Under this setting, the system
dynamically allocates resources to Plug and Play devices as they are required.
If you cannot get a legacy ISA (Industry Standard Architecture) expansion card to work
properly, you might be able to solve the problem by changing this item to Manual, and
then opening up the IRQ Resources submenu.
•
IRQ Resources (Press Enter):In the IRQ Resources submenu, if you assign an IRQ to Legacy ISA, then that Interrupt Request Line is reserved for a
legacy ISA expansion card. Press <Esc> to close the IRQ Resources submenu.
In the Memory Resources submenu, use the first item Reserved memory Base
to set the start address of the memory you want to reserve for the ISA
expansion card. Use the second item Reserved Memory Length to set the
amount of reserved memory. Press <Esc> to close the Memory Resources
submenu.
PCI/VGA Palette Snoop [Disabled]
This item is designed to overcome problems that can be caused by some non-standard
VGA cards. This board includes a built-in VGA system that does not require palette
snooping so you must leave this item disabled.
Assign IRQ For USB [Enabled]
Names the interrupt request (IRQ) line assigned to the USB on your system. Activity of
the selected IRQ always awakens the system.
Using BIOS
43
PC Health Status
On motherboards that support hardware monitoring, this item lets you monitor the
parameters for critical voltages, temperatures and fan speeds.
Phoenix-AwardBIOS CMOS Setup Utility
PC Health Status
Shutdown Temperature
Warning Temperature
CPU Vcore Voltage
+2.5V
+3.3V
+5V
+12V
5VSB (V)
VBT (V)
CPU Temperature
System Temperature
CPU Fan Speed
System Fan Speed
Power Fan Speed
Power 20/24Pin Message
Item Help
[Disabled]
[Disabled]
Menu Level
[Enabled]
123
123
123
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Shutdown Temperature [Disabled]
Enables you to set the maximum temperature the system can reach before powering down.
Warning Temperature [Disabled]
This item allows users to manually set the warning temperature of the system.
System Component Characteristics
These fields provide you with information about the systems current operating status.
You cannot make changes to these fields.
•
CPU Vcore Voltage
•
Memory Voltage
•
CPU Temperature
•
System Temperature
•
CPU Fan Speed
•
SYSTEM Fan Speed
•
Power Fan Speed
Power 20/24Pin Message [Enabled]
This item allows users to enable or disable the 20/24pin power cable indication message.
Using BIOS
44
Frequency/Voltage Control
This item enables you to set the clock speed and system bus for your system. The clock
speed and system bus are determined by the kind of processor you have installed in your
system.
Phoenix-AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
AMD K8 Cool ‘n’ Quiet control
Hammer Fid control
Hammer Vid control
Auto Detect PCI Clk
Spread Spectrum
CPU Clock
DIMM Voltage Adjust
[Auto]
[StartUp]
[StartUp]
[Enabled]
[+/- 0.3%]
[100 MHz]
[2.6 V]
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
AMD K8 Cool ’n’ Quiet control (Auto)
This item helps the system to lower the frequency when CPU idles. When the frequency
decreases, the temperature will drop automatically as well.
Hammer FID Control (StartUp)
This item allows users to adjust the CPU frequency; the range will be varied according to
different CPUs. We strongly recommend you leave this item at its default value.
Hammer VID Control (StartUp)
This item allows users to adjust the CPU voltage. We strongly recommend you leave this
item at its default value.
Auto Detect PCI Clk (Enabled)
When this item is enabled, BIOS will disable the clock signal of free PCI slots.
Spread Spectrum (+/- 0.3%)
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic
Interference) generated by the system.
CPU Clock (100 MHz)
This item allows users to manually adjust the CPU lock.
DIMM Voltage Adjust (2.6V)
Use this item to manually adjust the DIMM voltage, from.
Using BIOS
45
Load Performance Defaults
If you select this item and press Enter a dialog box will appear. If you select [OK], and
then Enter, the Setup Utility loads a set of performance default values. These default
settings are quite demanding and your system might not function properly if you are
using slower CPU, memory, or other low-performance components.
Warning: To load Performance settings may make your system become
unstable or unbootable. When loading the Performance Defaults fails,
users can choose “either” step to return the motherboard to its defaults
BIOS:
1. Power on the system and press “Insert” key. The system will bypass the
previous BIOS setting and automatically reload the default BIOS.
(This procedure is BIOS setup only!)
2. Apply to the jumper setting reference onboard and proceed with the
“Clear CMOS” to recover the default BIOS setting. Please refer to
Chapter 2, page 9, to complete the clear CMOS action. (This
procedure requires opening the chasis!)
Load Optimized Defaults
This option opens a dialog box that lets you install optimized defaults for all appropriate
items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press
<N> and then <Enter> to not install the defaults. The optimized defaults place demands on the system that may be greater than the performance level of the components,
such as the CPU and the memory. You can cause fatal errors or instability if you install
the optimized defaults when your hardware does not support them. If you only want to
install setup defaults for a specific option, select and display that option, and then press
<F7>.
Users please remain the factory BIOS default setting of “Load optimized
Defaults” when install Operation System onto your system.
Set Supervisor/User Password
When this function is selected, the following message appears at the center of the screen
to assist you in creating a password.
ENTER PASSWORD
Type the password, up to eight characters, and press <Enter>. The password typed now
will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection.
To disable password, just press <Enter> when you are prompted to enter password. A
message will confirm the password being disabled. Once the password is disabled, the
system will boot and you can enter BIOS Setup freely.
PASSWORD DISABLED
If you have selected “System” in “Security Option” of “BIOS Features Setup” menu,
you will be prompted for the password every time the system reboots or any time you try
to enter BIOS Setup.
If you have selected “Setup” at “Security Option” from “BIOS Features Setup” menu,
you will be prompted for the password only when you enter BIOS Setup.
Using BIOS
46
Supervisor Password has higher priority than User Password. You can use Supervisor
Password when booting the system or entering BIOS Setup to modify all settings. Also
you can use User Password when booting the
system or entering BIOS Setup but can not modify any setting if Supervisor Password
is enabled.
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in the
Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears,
press <Y> to save and exit, or press <N> to return to the main menu.
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in the
Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box
appears, press <Y> to discard changes and exit, or press <N> to return to the main
menu.
If you have made settings that you do not want to save, use the “Exit
Without Saving” item and press <Y> to discard any changes you have
made.
This concludes Chapter 3. Refer to the next chapter for information on the software
supplied with the motherboard.
Using BIOS
47
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the motherboard package contains all the
drivers and utility programs needed to properly run the bundled products. Below you can find
a brief description of each software program, and the location for your motherboard
version. More information on some programs is available in a README file, located in the
same directory as the software.
Never try to install all software from folfer that is not specified for use with your
motherboard.
Before installing any software, always inspect the folder for files named README.TXT,
INSTALL.TXT, or something similar. These files may contain important information that
is not included in this manual.
Auto-installing under Windows 2000/XP
The Auto-install CD-ROM makes it easy for you to install the drivers and software for your
motherboard.
If the Auto-install CD-ROM does not work on your system, you can still install
drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.
The support software CD-ROM disc loads automatically under Windows 98/ME/2000/XP.
When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and
Exit.
If the opening screen does not appear; double-click the file “setup.exe” in
the root directory.
Using the Motherboard Software
48
Setup Tab
Setup
Click the Setup button to run the software installation program. Select
from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows
you to open Windows Explorer and show the contents of the support
CD.
Before installing the software from Windows Explorer, look for a file
named README.TXT, INSTALL.TXT or something similar. This file
may contain important information to help you install the software
correctly.
Some software is installed in separate folders for different operating
systems, such as DOS, WIN NT, or WIN98/95. Always go to the correct
folder for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or INSTALL.EXE
by double-clicking the file and then following the instructions on the
screen.
Exit
The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1.
Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be
different according to the motherboard you are installing.
The motherboard identification is located in the upper left-hand corner.
Using the Motherboard Software
49
2.
Click Next. The following screen appears:
3.
Check the box next to the items you want to install. The default options are recommended.
4.
Click Next run the Installation Wizard. An item installation screen appears:
5.
Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the
installation.
Using the Motherboard Software
50
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory.
This file contains the information needed to locate the drivers for your motherboard.
Look for the chipset and motherboard model; then browse to the directory and path to
begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup
program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the operating
system subfolder and locate the readme text file (README.TXT or README.DOC) for
information on installing the driver or software for your operating system.
Utility Software Reference
All the utility software available from this page is Windows compliant. They are provided
only for the convenience of the customer. The following software is furnished under license
and may only be used or copied in accordance with the terms of the license.
These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.
AMI/AWARD Flash Utility
This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard,
and lets you copy an updated version of the BIOS to the chip. Proceed with caution when
using this program. If you erase the current BIOS and fail to write a new BIOS, or write a
new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for
more information.
WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility.
The utility enables you to flash the system BIOS stored on a Flash Memory chip on the
motherboard while in a Windows environment. This utility is currently available for
WINXP\ME\2000\98SE. To install the WinFlash utility, run WINFLASH.EXE from the
following directory: \UTILITY\WINFLASH 1.51
This concludes Chapter 4.
Using the Motherboard Software
La RX480-A utilise un socket de 939 broches ayant les caractéristiques suivantes :
•
Peut recevoir les processeurs AMD Sempron/Athlon64/Athlon 64 FX
•
Prend en charge des vitesses d’interface HyperTransportTM (HT) allant
jusqu’à 2000MT/s
La Technologie HyperTransportTM est une liaison point à point entre deux matériels, elle
permet à des circuits intégrés d’échanger des informations à des vitesses bien plus élevées
que ne le permettent les technologies à interconnexions actuellement disponibles.
Chipset
Les chipsets RX480 Northbridge (NB) et SB400 Southbridge (SB) sont basés sur une
architecture novatrice et dimensionnable avec une fiabilité et des performances prouvées.
RX480 (NB)
•
1 x2 (extensible à x4) interface A-Link Express (conforme
PCI Express 1.0a ) pour connexion à la ATI IXP
•
Prend en charge un PCI Express x16 pour Interface
Graphique, entièrement conforme à la Spécification de Base
PCI Express révision 1.0a.
•
Prend entièrement en charge les états ACPI S1, S3, S4 et
S5.
•
Prend en charge la solution à simple puce dans la technologie CMOS 0,13 micron, 1,0-1,2v
SB400 (SB)
•
•
•
•
•
Mémoire
•
•
Interface 2/4-lane A-Link Express (conforme PCI Express
1.0a) à RADEON IGPs
Conforme aux spécifications PCI 2.3, jusqu’à 7 périphériques maîtrise de bus pris en charge
Quatre périphériques Serial ATA pris en charge, conforme
aux spécifications Serial ATA 1.0, RAID 0 et RAID 1 accommodés
Contrôleur d’Hôte USB 2.0 intégré prenant en charge jusqu’à
huit ports USB 2.0
Contrôleur IDE intégré prenant en charge les modes Ultra
DMA 133/100/66/33
SDRAM DDR 400/333/266 DDR avec double canal pris en charge
Peut recevoir quatre DIMM sans tampon, taille mémoire maximum de 4
Go
Audio (optionnel)
Cette carte mère prend en charge les chipsets Audio suivants :
•
Conforme aux spécifications AC’97 2.3
•
CODEC full-duplex 16 bits avec vitesse d’échantillonnage de 48MHz
•
Prend en charge la vitesse d’échantillonnage double (96KHz) de la
lecture audio DVD
•
Compatible Direct Sound 3DTM
•
•
•
Conforme aux spécifications AC’97 2.3, prenant en charge les DAC 8
canaux
Répond aux exigences de performances pour l’audio sur les systèmes
PC99/2001
Conforme aux exigences audio de Microsoft WHQL/WLP 2.0
Multi-Language Translation
Français
Caractéristiques
Processeur
Français
LAN interne (optionnel)
Cette carte mère prend en charge les chipsets LAN suivants :
•
•
•
Supporte le fonctionnement en Auto-négociation N-Way en 10/100Mbps
Prend en charge la fonction Wake-On-LAN (WOL) (réveil par appel
réseau) et le réveil à distance
Prend en charge les broches LED pour diverses indications d’activités
de réseau
Prend en charge le Contrôle de Flux Full Duplex (IEEE 802.3x)
•
•
•
•
Emetteur-récepteur 10/100/1000 intégré
Prend en charge PCI v2.3, 32 bits, 33/66-MHz
Détection de croisement & Correction auto
Prise en charge de Réveil par LAN et réveil distant
•
1394a FireWire (Optionnel)
•
•
Entièrement conforme avec provisions de IEEE Std 1394-1995 pour les
bus série de hautes performances et IEEE Std 1394a-2000
Deux ports de câble entièrement conforme IEEE Std 1394a-2000 à 400M
bits/s
Options d’extension
La carte mère est livrée avec les options d’extensions suivantes:
•
Un PCI Express x16 pour Interface Graphique
•
Deux logements PCI Express x1
•
Trois emplacements PCI v2.3 bits
•
Deux connecteurs IDE de 40 broches prenant en charge jusqu’à quatre
périphériques IDE
•
Une interface de lecteur de disquette
•
Quatre connecteurs SATA à 7 broches
La carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de transfert de
133/100/66/33 Mo/s.
E/S intégrées
La carte mère possède un jeu complet de ports d’E/S et de connecteurs:
•
Deux ports PS/2 pour souris et clavier
•
Un port série
•
Un port parallèle
•
Quatre ports USB
•
Un port 1394a (optionnel)
•
Un port LAN (optionnel)
•
Prises audio pour entrée microphone, ligne d’entrée et sortie Audio 8 canaux
Microprogramme BIOS
La carte mère utilise Award BIOS qui permet aux utilisateurs de configurer de nombreuses
caractéristiques du système comprenant les suivantes:
•
Gestion de l’alimentation
•
Alarmes de réveil
•
Paramètres de CPU
•
Synchronisation du CPU et de la mémoire
Le microprogramme peut aussi être utilisé pour définir les paramètres pour les vitesses d’horloges
de différents processeurs.
Certaines spécifications matérielles et éléments de logiciels peuvent être modifiés
sans avertissement.
Multi-Language Translation
Das RX480-A verwendet einen 939-Pin Socket mit den folgenden Merkmalen:
•
Nimmt AMD Sempron/Athlon64/Athlon 64 FX Prozessoren auf
•
Unterstützt bis zu 2000MT/s HyperTransportTM(HT) InterfaceGeschwindigkeiten
HyperTransport TM Technologie ist ein Punkt-zu-Punkt Link zwischen zwei Geräten. Es
ermöglicht integrierten Schaltkreisen einen Informationsaustausch mit wesentlich höherer
Geschwindigkeit als bei gängigen Interconnect-Technologien.
Chipsatz
Die RX480 Northbridge (NB) und SB400 Southbridge (SB) Chipsätze basieren auf einer
innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung.
•
1 x2 (auf x4 erweiterbar) A-Link Express Interface (entspricht
RX480(NB)
PCI Express 1.0a) für die Verbindung zu ATI IXP
•
Unterstützt eine PCI Express x16 Grafik-Interface, mit vollständiger Entsprechung zur PCI Express Base Spezifikation
Revision 1.0a.
•
Vollständige Unterstützung für ACPI-Modi S1, S3, S4 und
S5.
•
Unterstützt Single-Chip-Lösung in 0,13 Mikron, 1.0-1.2v
CMOS-Technologie
SB400 (NB)
•
2/4-Lane A-Link Express Interface (entspricht PCI Express
1.0a) zu RADEON IGPs
Entspricht PCI 2.3 Spezifikation, es werden bis zu 7 Busmaster-Geräte unterstützt
Unterstützung für vier Serial ATA-Geräte, entspricht Serial
ATA 1.0 Spezifikation, nimmt RAID 0 und RAID 1 auf
Integrierter USB 2.0 Host-Controller unterstützt bis zu acht
USB 2.0 Ports
Integrierter IDE-Controller unterstützt Ultra DMA 133/100/66/33
Modi
•
•
•
•
Speicher
•
•
Unterstützung für DDR 400/333/266 DDR SDRAM mit Dualkanal
Nimmt vier ungepufferte DIMMs auf; die maximale Speichergröße beträgt
bis zu 4 GB
Audio (Optional)
Dieses Mainboard kann einen der folgenden Audio-Chipsätze unterstützen:
•
•
•
•
•
•
•
Entspricht AC’97 2.3 Spezifikationen
16-Bit Stereo-Vollduplex CODEC mit einer Samplingrate von 48MHz
Unterstützt bei der DVD-Audiowiedergabe die doppelte Samplingrate
(96KHz)
Kompatibel mit Direct Sound 3DTM
Entspricht AC’97 2.3 Spezifikation, unterstützt 8-Kanal DACs
Entspricht den Leistungsanforderungen für Audio auf PC99/2001 Systemen
Entspricht den Microsoft WHQL/WLP 2.0 Audio-Anforderungen
Multi-Language Translation
Deutsche
Feature
Prozessor
Integriertes LAN (optional)
Dieses Mainboard kann einen der folgenden LAN-Chipsätze unterstützen:
Deutsche
•
•
•
•
Unterstützt den Betrieb bei 10/100Mbps N-Way Auto-Negotiation
Unterstützt Wake-On-LAN-Funktion und Remote-Wake-up
Unterstützt LED-Pins für die Anzeige verschiedener Netzwerkaktivitäten
Unterstützt Vollduplex-Flusskontrolle (IEEE 802.3x)
•
•
•
•
Enthält 10/100/1000 Transceiver
Unterstützung von PCI v2.3, 32-Bit, 33/66-MHz
Crossover Detection & Auto-Correction
Unterstützung für Wake-on-LAN und Remote Wake-up
1394a FireWire (Optional)
•
•
Vollständige Entsprechung zu den Vorschriften des IEEE Std 1394-1995 für
den Hochleistungs-Serial-Bus und IEEE Std 1394a-2000
Zwei vollständig IEEE Std 1394a-2000 konforme Kabelports bei 400M Bits/s
Erweiterungsoptionen
Das Motherboard bietet die folgenden Erweiterungsoptionen:
•
Ein PCI-Express x16 für eine Grafikschnittstelle
•
Zwei PCI Express x1 Slots
•
Drei 32-bit PCI v2.3-Steckplätze
•
Zwei 40-Pin IDE Stecker, vier IDE-Kanäle unterstützen
•
Ein Steckplatz für ein Diskettenlaufwerk
•
Vier 7-Pin SATA-Stecker
Das Motherboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate von
133/100/66/33 MB/Sek.
Integrierte I/O-Schnittstellen
Das Motherboard verfügt über einen kompletten Satz von I/O-Schnittstellen und Anschlüssen:
•
Zwei PS/2-Schnittstellen für Tastatur und Maus
•
Eine serielle Schnittstelle
•
Eine parallele Schnittstelle
•
Vier VGA- Schnittstellen
•
Eine 1394a-Schnittstelle (optional)
•
Eine LAN-Schnittstelle (optional)
•
Audiobuchsen für Mikrofon-in, Line-in und 8-Kanal Audioausgabe
BIOS Firmware
Dieses Motherboard setzt das AWARD BIOS ein, mit dem der Anwender viele
Systemeigenschaften selbst konfigurieren kann, einschließlich der folgenden:
•
Energieverwaltung
•
Wake-up Alarm
•
CPU-Parameter
•
CPU- und Speichertiming
Mit der Firmware können auch Parameter für verschiedene Prozessortaktgeschwindigkeiten
eingestellt werden.
Einige Hardware- und Software-Spezifikationen können jederzeit und ohne
vorherige Ankündigung geändert werden.
Multi-Language Translation
RX480-A è dotata di una presa a 939 pin che offre le seguenti caratteristiche:
•
Compatibilità con processori AMD Sempron/Athlon64/Athlon 64 FX
•
Supporto di velocità di interfaccia HyperTransportTM (HT) fino a 2000 MT/s
La tecnologia HyperTransportTM consente il collegamento point-to-point fra due dispositivi
e quindi un trasferimento di informazioni tra circuiti integrati molto più veloce di quanto sia
possibile con le attuali tecnologie di interconnessione.
Chipset
I chipset RX480 Northbridge (NB) e SB400 Southbridge (SB) sono basati su un’innovativa
architettura scalabile e offrono collaudata affidabilità e prestazioni comprovate.
RX480 (NB)
•
1 interfaccia Express A-Link x2 (espandibile a x4), conforme a
PCI Express 1.0a, per collegamenti a ATI IXP
•
Supporto di una PCI Express x16 per interfaccia grafica con
conformità completa alla revisione 1.0a della specifica PCI
Express Base
•
Supporto completo di stati S1, S3, S4 e S5 ACPI.
•
Supporto di soluzione Single chip in 0,13 micron, tecnologia
1.0-1.2v CMOS
SB400 (SB)
•
•
•
•
•
Interfaccia A-Link Express a 2/4 vie (conforme a PCI Express
1.0a) ai protocolli IGP RADEON
Conforme alla specifica PCI 2.2 a 33 MHz, con supporto di fino
a 7 periferiche master bus
Supporto di quattro periferiche ATA seriali, conforme alla specifica Serial ATA 1.0, compatibile con RAID 0 e RAID 1
Controller host USB 2.0 integrato con supporto di fino a otto
porte USB 2.0
Controller IDE integrato con supporto di modalità Ultra DMA
133/100/66/33
Memoria
•
•
Supporto di SDRAM DDR 400/333/266 con Dual Channel
Compatibile con quattro DIMM senza buffer con una capacità massima di
memoria di 4 GB
Audio (Opzionale)
La scheda madre offre supporto per i seguenti chipset audio
•
•
•
Conforme alle specifiche AC’97 2.3
CODEC full-duplex stereo a 16 bit con velocità di campionamento di 48
KHz
Supporto di velocità di campionamento doppia (96 KHz) per la
riproduzione audio di DVD
Compatibile con Direct Sound 3DTM
•
•
•
Conforme alla specifica AC’97 2.3 con supporto di DAC a 8 canali
Conforme ai requisiti di prestazione audio su sistemi PC99/2001
Conforme ai requisiti audio di WHQL e WLP 2.0 di Microsoft
•
Multi-Language Translation
Italiano
Caratteristiche
Processore
LAN integrata (opzionale)
La scheda madre offre supporto per uno dei seguenti chipset LAN:
Italiano
•
•
•
•
Supporto di NWay Auto-negotiation a 10/100 Mbps
Supporto di funzionalità Wake-On-LAN e riattivazione remota del sistema
Supporto di pin LED per indicazioni di attività di rete
Supporto di controllo flusso full duplex (IEEE 802.3x)
•
•
•
•
Transceiver 10/100/1000 integrato
Supporta PCI v2.3, 32-bit, 33/66-MHz
Rilevazione e crossover e autocorrezione
Supporto di funzionalità Wake-on-LAN e riattivazione remota
FireWire 1394a (Opzionale)
•
•
Conformità completa a disposizioni IEEE Std 1394-1995 per bus seriale a
elevate prestazioni e IEEE Std 1394a-2000
Due porte cable a 400M bit/s conformi a IEEE Std 1394a-2000
Opzioni di espansione
La scheda madre è dotata delle seguenti opzioni di espansione:
•
Un PCI Express x16 per interfaccia grafica
•
Due slot PCI Express x1
•
Tre slot PCI v2.3 a 32 bit
•
Due connettori 40pin IDE per il supporto di fino a quattro dispositivi IDE
•
Un’interfaccia per unità disco floppy
•
Quattro connettori SATA a 7 pin
La scheda madre supporta bus master UltraDMA con tasso di trasferimento di 133/100/66/33
MB/s.
I/O integrati
La scheda madre offre una serie completa di porte e connettori I/O:
•
Due porte PS/2 per mouse e tastiera
•
Una porta seriale
•
Una porta parallela
•
Quattro porte USB
•
Una porta 1394a (opzionale)
•
Una porta LAN (opzionale)
•
Prese jack audio per ingresso microfonico, line-in e uscita Audio a 8 canali
Firmware BIOS
La scheda madre si avvale del BIOS AWARD che consente la configurazione personalizzata di
molte funzionalità del sistema, tra cui:
•
Gestione dell’alimentazione
•
Allarmi di attivazione
•
Parametri CPU
•
Sincronizzazione di CPU e memoria
Il firmware consente inoltre di impostare i parametri per diverse velocità di clock del
processore.
Alcune specifiche hardware e voci di software possono essere modificate senza
preavviso.
Multi-Language Translation
La RX480-A usa un zócalo 939-pin que lleva las sigtes. características:
•
Acomoda procesadores AMD Sempron/Athlon64/Athlon 64 FX
•
Soporta hasta las velocidades de interfaz 2000MT/s HyperTransport TM
(HT)
La Tecnología HyperTransport TM es un vínculo punto a punto entre dos dispositivos, habilita
circuitos integrados para intercambiar la información en velocidades más rápidas que las
tecnologías de interconexión disponibles actualmente.
Chipset
El chipset RX480 Northbridge (NB) y SB400 Southbridge (SB) se basan de una arquitectura
innovadora y escalable con fiabilidad y rendimiento comprobados.
•
1 interfaz x2 (expansible a x4) A-Link Express (conformidad
RX480 (NB)
PCI Express 1.0a) para conectar al ATI IXP
•
Soporta un PCI Express x16 para la Interfaz de Gráficas,
conformidad completa a la revisión de la Especificación Base
de PCI Express 1.0a.
•
Soporte completo de ACPI states S1, S3, S4 y S5.
•
Soporta la solución de chip singular en la tecnología CMOS
de 0.13 micron, 1.0-1.2v
SB400 (SB)
•
•
•
•
•
Memoria
•
•
Interfaz 2/4-lane A-Link Express (conformidad PCI Express
1.0a) a los RADEON IGPs
Conformidad con la especificación PCI 2.3, hasta dispositivos másters de bus 7 soportados
Cuatro dispositivos Serial ATA soportados, conformidad con
la especificación Serial ATA 1.0, acomodando RAID 0 y RAID
1
Controlador Anfitrión USB 2.0 integrado que soporta hasta
ocho puertos USB 2.0
Controlador IDE integrado que soporta los modos Ultra DMA
133/100/66/33
DDR 400/333/266 DDR SDRAM con soporte de Canal Dual
Acomoda cuatro DIMMs sin buffer, hasta 4 GB de tamaño de memoria
máximo
Audio (optativo)
Esta placa principal puede soportar cualquiera de los sigtes. chipset de Audio:
•
•
•
•
•
•
•
Conformidad con las especificaciones AC’97 2.3
CODEC de full-duplex estéreo de 16-bit con índice de muestreo de
48MHz
Soporta doble índice de muestreo (96KHz) de reproducción de audio
DVD
Compatible con Direct Sound 3DTM
Conformidad de la especificación AC’97 2.3, que soporta 8-ch DACs
Satisface los requisitos de rendimiento para el audio en los sistemas
PC99/2001
Satisface los requisitos de audio de Microsoft WHQL/WLP 2.0
Multi-Language Translation
Español
Característica
Procesador
LAN Abordo (optativo)
Esta placa principal puede soportar uno de los sigtes. chipset LAN:
•
•
•
•
•
Español
•
•
•
Soporta operación de Autonegociación N-Way de 10/100Mbps
Soporta la función Wake-On-LAN y despertar remoto
Soporta pins de LED para varias indicaciones de actividad de red de
trabajo
Soporta Full Duplex Flow Control (IEEE 802.3x)
Transceptor 10/100/1000 integrado
Soporta PCI v2.3, 32-bit, 33/66-MHz
Detección Cruzada & Autocorrección
Soporte de Despertar-en-LAN y Despertar remoto
1394a FireWire (optativo)
•
•
Conformidad total con las provisiones de IEEE Std 1394-1995 para un bus
serial de alto rendimiento y IEEE Std 1394a-2000
Dos puertos de cable con conformidad total de IEEE Std 1394a-2000 en 400M
bits/s
Opciones de Expansión
La placa principal viene con las sigtes. opciones de expansión:
•
Un PCI Express x16 para la Interfaz de Gráficas
•
Dos ranuras PCI Express x1
•
Tres ranuras conforme con 32-bit PCI v2.3
•
Dos conectores 40-pin IDE que soporta hasta cuatro dispositivos
•
Una interfaz de la unidad de disco floppy
•
Cuatro conectores SATA de 7-pin
La placa principal soporta el mastering de bus UltraDMA con índices de transferencia de
133/100/66/33 MB/s.
I/O Integrado
La placa principal tiene un juego completo de puertos y conectores I/O:
•
Dos puertos PS/2 para ratón y teclado
•
Un puerto serial
•
Un puerto paralelo
•
Cuatro puertos USB
•
Un puerto 1394a (optativo)
•
Un puerto LAN (optativo)
•
Clavijas de audios para la microphone in (entrada de micrófono), line-in
(entrada de línea) y salida de audio de 8-canales
BIOS Firmware
La placa principal usa AWARD BIOS que habilita usuarios para configurar muchas
características de sistema que incluyen las sigtes:
•
Administración de Alimentación
•
Alarmas para despertar
•
Parámetros de CPU
•
Cronometraje de CPU y de memoria
También se lo puede usar el firmware para configurar los parámetros para diferentes velocidades
de reloj de procesador.
Algunas especificaciones de hardware e ítems de software son sujetos a cambio
sin aviso previo.
Multi-Language Translation
Características
Processador
O RX480-A usa uma ficha de 939 pinos que comporta as seguintes características:
•
Acomoda processadores AMD Sempron/Athlon64/Athlon 64 FX
•
Suporta velocidades de interface de HyperTransportTM (HT) até 2000MT/
s
Tecnologia de HyperTransport TM Té um link ponto-a-ponto entre dois dispositivos, permite
circuitos integrados para trocar informação a velocidades muito mais elevadas que as
disponíveis actualmente em tecnologias de interconexão.
O conjunto de chips RX480 Northbridge (NB) e SB400 Southbridge (SB) é baseado numa
arquitectura inovadora e escalável com fiabilidade e performance provadas.
RX480 (NB)
•
1 x2 (expansível para x4) interface A-Link Express (compatível
com PCI Express 1.0a) para ligação ao ATI IXP
•
Suporta um PCI Express x16 para Interface de Gráficos,
cumpre totalmente com a revisão 1.0a. da Especificação de
Base de PCI Express.
•
Suporta na totalidade estados ACPI S1, S3, S4 e S5.
•
Suporta solução de chip único em 0.13 micron, tecnologia
1.0-1.2v CMOS
SB400 (SB)
•
Interface 2/4-lane A-Link Express (compatível com PCI Express 1.0a) para RADEON IGPs
Cumpre com a especificação 2.3 PCI, suporta até 7 dispositivos bus mestre
Suporta quatro dispositivos ATA de Série, cumprindo com a
especificação 1.0 ATA de Série, RAID 0 e RAID 1 acomodados
Controlador Host 2.0 USB Integrado suportando até oito portas
USB 2.0
Controlador IDE integrado que suporta modos Ultra DMA
133/100/66/33
•
•
•
•
Memória
•
•
DDR 400/333/266 DDR SDRAM com suporte de Bicanal
Acomoda quatro DIMMs sem buffers, com até 4 GB de limite de memória
máxima
Áudio (opcional)
Esta motherboard pode suportar qualquer um dos seguintes conjuntos de chips Áudio.
•
•
•
•
•
•
•
Cumpre com as especificações AC’97 2.3
CODEC duplex total Estéreo de 16 bits com taxa de amostragem de
48MHz
Suporta taxa de amostragem dupla (96KHz) de reprodução áudio DVD
Compatível com Direct Sound 3DTM
Compatível com a especificação AC’97 2.3, suportando 8-ch DACs
Cumpre com os requisitos de performance para áudio em sistemas
PC99/2001
Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft audio
Multi-Language Translation
Português
Conjunto de Chips
Onboard LAN (opcional)
Esta motherboard poderá suportar qualquer um dos seguintes conjuntos de chips LAN:
•
•
•
•
Suporta operação de Auto-negociação N-Way 10/100Mbps
Suporta função LAN de Despertar e despertar remoto
Suporta pinos LED para várias indicações de actividade de rede
Suporta Controlo de Fluxo Duplo Completo (IEEE 802.3x)
•
•
•
•
Suporta PCI v2.3, 32-bit, 33/66-MHz
Detecção Crossover & Auto Correcção
Suporte Wake-on-LAN e wake-up remoto
Transreceptor integrado 10/100/1000
Português
1394a FireWire (opcional)
•
•
compatível com provisões de IEEE Std 1394-1995 para um bus de série de
elevada performance e IEEE Std 1394a-2000
Duas portas para cabo totalmente compatíveis com IEEE Std 1394a-2000 a
400M bits/s
Opções de Expansão
A motherboard é fornecida com as seguintes opções de expansão:
•
Um PCI Express x16 para Interface de Gráficos
•
Duas ranhuras 1 x PCI Express
•
Três ranhuras compatíveis com PCI v2.3 de 32 bits
•
Dois conectores IDE 40 pinos, que suportam até quatro dispositivos IDE
•
Um interface com drive de disco flexível
•
Quatro conectores SATA de 7 pin
A motherboard suporta um domínio bus UltraDMA bus com taxas de Transferência de
133/100/66/33 MB/s.
I/O Integrado
A motherboard possui um conjunto completo de portas I/O e conectores:
•
Duas portas PS/2 para rato e teclado
•
Uma porta de série
•
Uma porta paralela
•
Quatro portas USB
•
Uma porta 1394a (opcional)
•
Uma porta LAN (opcional)
•
Fichas áudio para entrada de microfone, entrada e saída de Áudio 8-ch
Microprogramação BIOS
Esta motherboard usa AWARD BIOS que permitem aos utilizadores configurar muitas
características do sistema incluindo as seguintes:
•
Gestão de corrente
•
Alarmes de despertar
•
Parâmetros CPU
•
Temporização de memória e CPU
A microprogramação poderá ser também usada para estabelecer parâmetros para diferentes
velocidades de relógio do processador.
Algumas especificações de hardware e itens de software poderão ser sujeitos a
alteraçõessem aviso prévio.
Multi-Language Translation
機能
プロセッサ
RX480-A が採用した939ピン仕様のソケットは、次の特徴があります:
•
AMD Sempron/Athlon64/Athlon 64 FX プロセッサの搭載に対応
•
転送率が最大2000MT/秒までの HyperTransportTM (HT)インターフェース
を採用
HyperTransportTM技術とは、二つのデバイスを1対1( point-to-point)で接続する技
術であり、従来のインターコネクト技術に比較して、集積回路同士の情報交換を高速化
します。
チップセット
RX480 (NB)
•
•
•
•
SB400 (SB)
•
•
•
•
•
1つの x2 ( x4に拡張可能) A-Link Express インターフェース (PCI
Express 1.0a に対応)でATI IXPに接続
グラフィックインターフェースとなる PCI Express x16 インターフェース
を搭載し、それでPCI Express Base Specification revision 1.0aに完
全対応
ACPI の S1、S3、S4 および S5の電源管理状態に完全対応
0.13ミクロンの1.0-1.2v CMOS 技術導入のシングルチップソリューショ
ンをサポート
2/4-レインのA-Link Express インターフェース (PCI Express 1.0a
に準拠) でRADEON IGPに対応
PCI 2.3 規格に対応し、最大7つまでのマスター装置の取り付けを可
能に
4つまでのSerial ATA 装置をサポートし、Serial ATA 1.0 規格に対応
しており、且つRAID 0 とRAID 1 の機能を提供
内蔵のUSB 2.0 ホストコントローラで最大8つまでのUSB 2.0ポートを
サポート
内蔵のIDEコントローラでUltra DMA 133/100/66/33の諸モードをサ
ポート
メモリ
•
•
デュアルチャネルのDDR 400/333/266 DDR SDRAMを採用
搭載されている4つの非バッファーDIMMで最大4 GBまでのメモリーの取り付
けを可能に
オーディオ (オプション)
本マザーボードは次のオーディオチップセットの何れかをサポートします:
•
•
•
•
AC’97 2.3 規格に準拠
48MHzサンプリングレートの16ビットステレオ全二重CODEC
DVD音声再生のダブルサンプリングレート(96KHz)に対応
Direct Sound 3DTM に対応
•
•
•
AC’97 2.3 規格に準拠で、8-ch のDACをサポート
PC99/2001 システムに関するオーディオ要求に適合
Microsoft WHQL/WLP 2.0 オーディオ要求に適合
Multi-Language Translation
日本語
RX480 Northbridge (NB)と SB400 Southbridge (SB)チップセットは、実証された信
頼性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。
オンボードLAN (オプション)
当マザーボードは次のLANチップセットのいずれかを搭載しております:
•
•
•
•
10/100Mbps N-way自動ネゴシエーション操作をサポート
Wake-On-LANと遠隔wake-up機能をサポート
ネットワーク状態インジケータ用のLEDピンを搭載
全二重フロー制御(IEEE 802.3x)をサポート
•
•
•
•
10/100/1000 トランシーバーを搭載済み
PCI v2.3, 32-bit, 33/66-MHzへの対応
クロスオーバー検出機能と自動修正機能を搭載
Wake-on-LANと遠隔 wake-upとの機能をサポート
1394a Fire Wire(オプション)
•
•
“IEEE Std 1394-1995 for a high-performance serial bus and IEEE Std
1394a-2000”の基準に完全対応
IEEE Std 1394a-2000 完全対応の2つのポートのそれぞれが400M bits/秒
の転送率を実現
日本語
拡張オプション
本マザーボードでは、次の拡張機能が利用できます。
•
グラフィック用のPCI Express x16 インターフェース が1つ
•
PCI Express x1 スロットが2つ
•
32ビットPCI v2.3 互換性スロット が3つ
•
40ピンIDEロープロフィルヘッダー(4つのIDEチャネルをサポート)が2つ
•
フロッピーディスクドライブインターフェイス が1つ
•
7ピンSATAコネクタ が4つ
このマザーボードは、133/100/66/33MB/秒の転送速度でのUltra DMAバスマスタリン
グをサポートします。
統合の入出力ポート
マザーボードには、次のI/Oポートやコネクタを揃えています。
•
•
•
•
•
•
•
マウスとキーボード用のPS/2ポート が2つ
シリアルポート が1つ
パラレルポート が1つ
USBポートが4つ
1394a ポート が1つ(オプション)
LANポート が1つ(オプション)
マイクロホン入力、ライン入力、および8-chのオーディオ出力の諸オーディオ
ジャックを搭載済み
BIOSファームウェア
本マザーボードはAWARD BIOSを採用し、次の機能を含む多様なシステムの構成をを
サポートします。
•
•
•
•
電源管理
ウェークアップアラーム
CPUパラメータ
CPUとメモリとのタイミング
さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更す
ることもできます。
一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更すること
があります。
Multi-Language Translation
특성
프로세서
RX480-A 는 939 핀 소켓을 사용하여 다음과 같은 특성을 지닌다:
•
AMD 샘프론/애슬론64/애슬론 64 FX 프로세서 사용
•
HyperTransportTM (HT) 인터페이스 속도 최대 2000MT/s 지원
HyperTransport TM 기술은 두 장치간의 point-to-point 링크로, 집적 회로가 기존의
상호 연결 기술 보다 더 빠른 속도로 정보를 교환할 수 있다.
칩셋
RX480 (NB)
•
•
•
•
SB400 (SB)
•
•
•
•
•
ATI IXP 연결을 위한 1 x2 (x4 확장 가능) A-Link Express
인터페이스 (PCI Express 1.0a 부합)
그래픽 인터페이스로 1 개의 PCI Express x16 지원, PCI
Express Base 사양 1.0a 부합.
ACPI states S1, S3, S4 및 S5 지원.
0.13 micron, 1.0-1.2v CMOS 테크놀로지의 싱글 칩 솔루션
지원
RADEON IGPs 용 2/4-lane A-Link Express 인터페이스
(PCI Express 1.0a 부합)
PCI 2.3 사양 부합, 최대 7 개의 버스 마스터 장치 지원
4 개의 시리얼 ATA 장치 지원, 시리얼 ATA 1.0 사양 부합,
RAID 0 및 RAID 1
최대 8 개의 USB 2.0 포트를 지원하는 통합 USB 2.0 호스
트 컨트롤러
Ultra DMA 133/100/66/33 모드를 지원하는 통합 IDE 컨트
롤러
메모리
•
•
DDR 400/333/266 DDR SDRAM, 듀얼 채널 지원
4 개의 unbuffered DIMMs, 최대 메모리 크기 4 GB
오디오
본 마더보드는 다음의 오디오 칩셋을 지원합니다.
•
•
•
•
AC’97 2.3 사양 부합
48MHz 샘플링 속도를 지닌 16 비트 스테레오 풀-듀플렉스 코덱
DVD 오디오 재생 시 더블 샘플링 속도 (96KHz) 지원.
Direct Sound 3DTM 호환
•
•
•
AC’97 2.3 사양 부합, 8 채널 DACs 지원
PC99/2001 시스템의 오디오를 위한 퍼포먼스 요구 조건 부합
마이크로소프트 WHQL/WLP 2.0 오디오 요구 조건 부합
Multi-Language Translation
한국어
RX480 Northbridge (NB) 및 SB400 Southbridge (SB) 칩셋은 혁신적이고 범위성을
지닌 아키텍쳐를 기반으로 인정된 신뢰성과 성능을 지닌다.
보드 내장 LAN (선택 사항)
본 마더보드는 다음과 같은 LAN 칩셋을 지원합니다:
•
•
•
•
10/100Mbps N-Way Auto-negotiation 작업 지원
Wake-On-LAN 기능 및 원격 wake-up 지원
다양한 네트워크 활동을 표시하는 LED 핀 지원
Full Duplex Flow Control (IEEE 802.3x) 지원
•
•
•
•
통합 10/100/1000 트랜시버
PCI v2.3, 32-bit, 33/66-MHz 지원
Crossover Detection 및 Auto-Correction
Wake-on-LAN 및 원격 wake-up 지원
1394a 파이어 와이어(선택 사항)
•
•
고성능 시리얼 버스를 위한 IEEE Std 1394-1995 및 IEEE Std 1394a-2000 부
합
400M bits/s 속도로 케이블 포트에 부합하는 2 개의 IEEE Std 1394a-2000
확장 옵션
한국어
본 마더보드의 확장 옵션은 다음과 같다:
•
그래픽 인터페이스를 위한 PCI 익스프레스 x16 1 개
•
PCI Express 2 개 x 슬롯1 개
•
32 비트 PCI v2.3 호환 슬롯 3 개
•
최대 4개의 IDE 장치를 지원하는 40핀IDE 커넥터 2 개
•
플로피 디스크 드라이브 인터페이스 1 개
•
7 핀 SATA 커넥터 4 개
마더보드는 전송 속도 133/100/66/33 MB/s의 UltraDMA 버스 마스터링을 지원한다.
통합 I/O
본 마더보드는 풀 셋트의 I/O 포트 및 커넥터가 있다:
•
마우스 및 키보드용 PS/2 포트 2 개
•
시리얼 포트 1 개
•
패러럴 포트 1 개
•
USB 포트 4 개
•
1394a 포트 1 개 (선택 사항)
•
LAN 포트 1 개 (선택 사항)
•
마이크폰 입력, 라인 입력 및 8 채널 오디오 출력 용 오디오 잭
BIOS 펌웨어
본 마더보드는 다음과 같은 시스템 특성을 구성할 수 있는 Award BIOS 를 사용한다:
•
전원 관리
•
Wake-up 알람
•
CPU 파라미터
•
CPU 및 메모리 타이밍
펌웨어로 다른 프로세서 클록 속도의 파라미터를 설정할 수도 있다.
몇 하드웨어 사양 및 소프트웨어 아이템은 사전 통보 없이 변경될 수 있습
니다.
Multi-Language Translation
功能
處理器
RX480-A採用1個939針插槽,該插槽具有如下特徵:
• 可安裝AMD Sempron/Athlon64/Athlon 64 FX 處理器
• 支援高達2000MT/秒的HyperTransportTM (HT)介面傳輸速率
HyperTransportTM技術為以點對點方式連接兩台設備的技術,藉此,積體電路間能夠以
後高於現有各種內部連接技術(interconnect technology)技術的速度來交換資訊。
晶片組
RX480 北橋(NB)及SB400 南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構,
具備優良的可靠性及性能。
•
•
•
•
SB400 (SB)
•
•
•
•
•
1個 2倍速 (可擴充至4倍速) A-Link Express介面 (PCI Express 1.0a 相容) 以連接ATI IXP
支援1個繪圖介面用之PCI Express x16,完全符合PCI Express
Base規格修訂版1.0a
完全支援 ACPI 的S1、S3、S4、及S5的狀態
支援有關0.13微米1.0-1.2v CMOS技術之單晶片解決方案
以2/4通道之A-Link Express 介面 (相容於PCI Express 1.0a
)連接RADEON IGP
符合PCI 2.3 規格,支援高達7匯流排主控裝置
支援4個Serial ATA裝置,符合Serial ATA 1.0 規格,並提供
RAID 0 及RAID 1功能
整合有USB 2.0主控器,可支援至8個USB 2.0埠
整合有IDE 控制器,可支援 Ultra DMA 133/100/66/33模式
記憶體
•
•
採用雙通道DDR 400/333/266 DDR SDRAM
設有4個非緩衝DIMM,最多可安裝4 GB記憶體
音頻(選購)
本主機板支援如下音訊晶片組的其中之一:
•
•
•
•
•
•
•
相容於AC’97 2.3 規格
16位元立體聲全雙工CODEC,取樣率48MHz
支援DVD音訊播放的雙取樣率(96KHz)
Direct Sound 3DTM 相容
相容於AC’97 2.3 規格,藉此支援8-ch DAC
符合PC99/2001系統音訊標準要求
符合Microsoft WHQL/WLP 2.0 音訊標準
Multi-Language Translation
繁體中文
RX480 (NB)
內建區域網路 (選購)
本主機板搭載有如下其中一種LAN晶片組:
•
•
•
•
支援 10/100Mbps N-way 自動協調作業
支援區域網路喚醒(Wake-On-LAN)及遠端喚醒功能
配有各種網路活動指示器用之LED接腳
支援全雙工流量控制(IEEE 802.3x)
•
•
•
•
整合有10/100/1000 收發器
支援PCI v2.3, 32位元, 33/66-MHz
具有跳接線偵測及自動修正功能
支援區域網路喚醒功能及遠距喚醒功能
1394a Fire Wire (選購)
•
•
完全支援"IEEE Std 1394-1995 for a high-performance serial bus 及
IEEE Std 1394a-2000" 規格
2個IEEE Std 1394a-2000連接埠,傳輸速率達400M bits/秒
擴充選項
本主機板包括下列擴充選項:
繁體中文
• 1 個繪圖卡用PCI Express x16 介面
• 2 個PCI Express x1 槽
• 3 個32位元PCIv2.3插槽
• 2 個40針 IDE 接頭,支援 4個 IDE 裝置
• 1 個軟碟機介面
• 4 個7針SATA插頭
本主機板支援傳輸率133/100/66/33 MB/秒下的Ultra DMA 匯流排主控功能。
整合 I/O
主機板具有一組齊全的 I/O 連接埠及連接頭:
•
•
•
•
•
•
•
2 個 PS/2 埠,供滑鼠與鍵盤使用
1 個串列埠
1 個平行埠
4 個USB埠
1 個1394a 埠(選購)
1 個區域網路埠(選購)
麥克風輸入、線級輸入、及8聲道音訊輸出等用之音訊插孔
BIOS 韌體
本主機板使用AWARD BIOS,使用者可以組態設定許多系統功能,包括如下:
• 電源管理
• 喚醒警鈴
• CPU參數
• CPU及記憶體的時脈定時
此外,也可藉由參數的設定,調整處理器的時脈速度。
部份硬體規格和軟體內容可能會在未經通知的情況下更動,敬請見諒。
Multi-Language Translation
功能
处理器
RX480-A 主板使用一个 939-pin 插座,此插座具有以下特点:
•
支持 AMD Sempron/Athlon64/Athlon 64 FX 处理器
•
支持 2000MT/s HyperTransportTM (HT) 接口速度
HyperTransportTM 技术是一种在两台设备间进行点到点连接的技术,它可以让集成电
路使用比当前互连技术更高的速度进行信息交换。
芯片组
RX480 北桥 (NB) 和 SB400 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构,能
提供已经证明的可靠性和高性能。
RX480 (NB)
•
1 x2 (可扩展到 x4) A-Link Express 接口(符合 PCI Express
1.0a 标准)用于连接到 ATI IXP
•
支持 1 个 PCI Express x16 用于图形接口,完全符合 PCI
Express Base 规格 1.0a。
•
完全支持 ACPI 状态 S1、S3、S4 和 S5
•
支持 0.13 微米单芯片解决方案,1.0-1.2v CMOS 技术
•
•
•
•
•
到 RADEON IGP 的 2/4-lane A-Link Express 接口(符合 PCI
Express 1.0a 标准)
符合 PCI 2.3 规格,最多支持 7 个总线设备
支持 4 个串行 ATA 设备,符合串行 ATA 1.0 规格,支持
RAID 0 和 RAID 1
集成 USB 2.0 主控器,最多支持 8 个 USB 2.0 端口
集成 IDE 控制器,支持 Ultra DMA 133/100/66/33 模式
内存
•
•
DDR 400/333/266 DDR SDRAM 双通道支持
支持 4 个非缓冲 DIMM,内存最大支持 4 GB
音频(可选)
此主板支持以下任何一种音频芯片组
•
•
•
•
兼容
具有
支持
符合
•
•
•
符合 AC’97 2.3 规格,支持 8 路 DAC
符合 PC99/2001 系统音频要求
符合 Microsoft WHQL/WLP 2.0 音频要求
AC’97 v2.3 规格
48MHz 采样速率的 16 位全双工 CODEC(编解码器)
DVD 音频播放的双采样速率 (96KHz)
Direct Sound 3DTM 规格
Onboard LAN(可选)
此主板支持以下任何一种 LAN 芯片组:
•
•
•
•
支持 10/100Mbps N 路自协商工作
支持 LAN 唤醒 (WOL) 功能和远程唤醒功能
支持用于各种活动指示灯的 LED 管脚
支持全双工流控制 (IEEE 802.3x)
•
•
•
•
支持 10/100/1000 Mbps 速度工作(10/100 Mbps 可选)
支持 PCI v2.3,32-位,33/66-MHz
跨接检测和自动校正
支持 LAN 和远程唤醒
Multi-Language Translation
简体中文
SB400 (SB)
1394a 火线(可选)
•
•
完全符合用于高性能串行总线的 IEEE Std 1394-1995 和 IEEE Std 1394a2000
2 个符合 IEEE Std 1394a-2000 标准的电缆端口,传输速率可达 400M bits/s
扩展选项
此主板提供如下扩展选项:
•
1 个用于图形接口的 PCI Express x16
•
2 个 PCI Express x1 插槽
•
3 个 32 位 PCI v2.3 扩展槽
•
2 个 40-pin IDE 接口,可支持 4 个 IDE 设备
•
1 个软驱接口
•
4 个 7-pin SATA 接口
主板支持 Ultra DMA 总线控制,传输速率可达 133/100/66/33MB/s。
集成 I/O
此主板具有完整的 I/O 端口和插孔:
•
2 个用于连接鼠标和键盘的 PS/2 端口
•
1 个串口
•
1 个并口
•
4 个 USB 端口
•
1 个 1394a 端口(可选)
•
1 个 LAN 端口(可选)
•
用于麦克风入、线入和 8 声道音频输出的音频插孔
简体中文
BIOS
此主板使用 AWARD BIOS,可以让用户自己配置以下系统功能:
•
电源管理
•
唤醒报警
•
CPU 参数
•
CPU 和记忆定时
还可用于设置不同处理器时钟速度的参数。
某些硬件规格和软件项目若有更改恕不另行通知。
Multi-Language Translation
Характеристики
Процессор
Плата RX480-A использует 939-штырьковый сокет и обладает следующими
характеристиками:
•
Размещает процессоры AMD Sempron/Athlon64/Athlon 64 FX
•
Поддерживает технологию 2000MT/s HyperTransportTM (HT)
Технология HyperTransport TM обеспечивает связь двух устройств по протоколу pointto-point, позволяя гораздо более быстрый обмен информацией между интегральными
микросхемами, чем тот, который обеспечивается существующими технологиями.
Чипсет
Чипсеты RX480 «Северный мост» (Northbridge, NB) и SB400 «Южный мост»
(Southbridge, SB) построены с использованием инновационной масштабируемой
архитектуры, обеспечивающей высокую надежность и производительность.
•
•
•
•
SB400 (SB)
•
•
•
•
•
Память
•
•
Один разъем A-Link Express x2 (c возможностью
расширения до x4) (совместимый с PCI Express 1.0a ) для
подключения ATI IXP
Поддерживает одну шину PCI Express x16 для
графического интерфейса, полностью совместима со
спецификацией PCI Express Base 1.0a.
Полностью поддерживает ACPI в режимах S1, S3, S4 и S5.
Поддерживает одночипную технологию 0.13 микрон, 1.01.2v CMOS
Интерфейс 2/4-lane A-Link Express (совместимость с PCI
Express 1.0a) для RADEON IGP
Совместимость со спецификацией PCI 2.3, поддержка до
7 устройств типа master
Поддержка четырех устройств Serial ATA, cовместимость
со спецификацией Serial ATA 1.0, размещение RAID 0 и
RAID 1
Встроенный контроллер хоста USB 2.0 с поддержкой до
восьми портов USB 2.0
Встроенный контроллер IDE с поддержкой режимов Ultra
DMA 133/100/66/33
DDR 400/333/266 DDR SDRAM с поддержкой двухканального режима
Размещает четыре модуля небуферируемой памяти DIMM с
максимальным объемом памяти до 4 ГБ
Аудио (опционально)
Эта материнская плата может обслуживать люой из следующих аудио чипсетов:
•
•
•
•
•
•
•
Совместимость со спецификацией AC’97 2.3
16-битный стерео CODEC (полный дуплекс) с частотой сэмплирования
48 МГц
Поддержка двойной скорости сэмплирования аудиовыхода DVD (96
кГц)
Совместимость с Direct Sound 3DTM
Совместимость со спецификацией AC’97 2.3, поддержка 8канальных DAC
Соответствие требованиям для аудио в системах PC99/2001
Соответствие требованиям для аудио Microsoft WHQL/WLP 2.0
Multi-Language Translation
Русский
RX480 (NB)
Встроенный сетевой адаптер LAN (опционально)
Встроенный сетевой адаптер LAN обладает следующими характеристиками:
•
•
•
•
•
•
•
•
Поддерживает автоматическое определение скорости и режима
соединения 10/100Mbps
Поддерживает функции Wake-On-LAN и remote wake-up
Поддержка светодиодов для индикации различной активности в сети
Поддерживает режим управления потоком Full Duplex Flow Control
(IEEE 802.3x)
Интегрированный трансивер 10/100/1000
Поддеркжа PCI v2.3, 32-бит, 33/66-MГц
Детекция и автокоррекция Crossover
Функция Wake-on-LAN и удаленного пробуждения
1394 Fire Wire(опционально)
•
•
Полная совместимость с требованиями стандарта IEEE Std 1394-1995
для скоростных серийных шин и стандарта IEEE Std 1394a-2000
Два кабельных порта, совместимых с IEEE Std 1394a-2000, со скоростью
передачи 400M бит/с
Возможности расширения
Русский
Существуют следуюшие опции расширения данной материнской платы:
•
Один разъем для карты графики PCI Express x16
•
Два слота PCI Express x1
•
Три 32-битных слота PCI v2.3
•
Два разъема 40-штырьковый IDE с поддержкой до четырех устройств
IDE
•
Один разъем для накопителя на гибких дисках
•
Четыре разъема 7-pin SATA
Плата поддерживает технологию захвата управления шиной UltraDMA bus mastering
со скоростью передачи данных 133/100/66/33 МБ/сек.
Интегрированный вход/выход
Плата снабжена полным набором портов входа/выхода и разъемов:
•
Два порта PS/2 для подключения мыши и клавиатуры
•
Один серийный порт
•
Один параллельный порт
•
Четыре портa USB
•
Один порт 1394a (опционально)
•
Один порт LAN (опционально)
•
Гнезда аудио для микрофона, входа и 8-канального выхода
BIOS
Плата работает под AWARD BIOS, который позволяет пользователю конфигурировать
различные характеристики системы:
•
Управление питанием
•
Сигналы пробуждения системы
•
Параметры CPU
•
Время доступа для CPU и памяти
BIOS допускает также установку параметров для различных частот процессора.
Некоторые параметры платы и характеристики ее программного
обеспечения могут быть изменены без предварительного уведомления.
Multi-Language Translation
Cechy
Procesor
Płyta główna RX480-A dostosowana jest do 939-nóżkowego gniazda i posiada następujące
właściwości:
•
Obsługuje procesory firmy AMD typu Sempron/Athlon64/Athlon 64 FX
•
Obsługuje złącze HyperTransportTM (HT) z szybkością do 2000MT/s
Technologia HiperTransportu TM jest protokołem komunikacji między dwoma urządzeniami,
który umożliwia układom zcalonym wymieniać informację z dużo większymi szybkościami
niż dotychczas stosowane technologie wzajemnych połączeń.
Chipset
Mostek północny (NB) RX480 i mostek południowy (SB) SB400 chipsetu oparty jest na
nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.
•
1 złącze x2 (rozszerzalne do x4) A-Link Express (zgodne ze
standardem PCI Express 1.0a) służące do podłączenia ATI
IXP
Obsługuje jedno graficzne złącze PCI Express x16, w pełni
zgodne ze standardem PCI Express Base w wersji 1.0a.
Całkowicie obsługuje ACPI w trybach S1, S3, S4 i S5
Obsługuje pojedyncze układy wykonane w technologii CMOS
0.13 mikrona, 1.0-1.2v
•
•
•
SB400 (SB)
•
•
•
•
•
Interfejs 2/4-lane A-Link Express (zgodny z PCI Express w wersji
1.0a) dla RADEON IGP
Zgodne ze standardem PCI w wersji 2.3 obslugujące do 7
urządzeń bus master
Obslugująca cztery urządzenia Serial ATA, zgodne ze standardem Serial ATA wersja 1.0, przystosowana do RAID 0 i RAID
1
Zintegrowany kontroler USB 2.0 obslugujący do do ośmiu gniazd
USB 2.0
Zintegrowany kontroler IDE obsługujący tryby pracy Ultra DMA
133/100/66/33
Pamięć
•
•
DDR 400/333/266 DDR SDRAM z obsługą dwu kanałów
Przystosowana do obsługi cztery banków niebuforowanej pamięci DIMM o
pojemności do 4 GB.
Audio (opcjonalnie)
Ta płyta główna może obsługiwać dowolny z następujących chipsetów audio:
•
•
•
•
•
•
•
Zgodne ze specyfikacją AC’97 w wersji 2.3
16 bitowe full-duplex CODEC z częstotliwością próbkowania 48MHz.
DVD audio playback obsługuje z podwójną częstotliwością próbkowania
(96KHz)
Zgodny z Direct Sound 3DTM
Zgodny ze specyfikacją AC’97 w wersji 2.3, obsługuje 8 kanałów DAC
Spełnia wymagania dla audio w systemie PC99/2001
Spełnia wymagania stawiane audio przez firmę Microsoft w systemie
WHQL/WLP 2.0
Multi-Language Translation
Polski
RX480 (NB)
Zintegrowana obsługa sieci LAN (opcjonalnie)
Zintegrowana obsługa sieci LAN posiada następujące właściwości:
•
•
•
•
•
•
•
•
Obsluguje N-drożne automatycznie ustalane operacje z szybkościami 10/
100Mbps
Obsługuje funkcję Wake-On-LAN i zdalnie sterowane wake-up
(uruchamianie komputera)
Obsługuje diody świetlne sygnalizujące różne aktywności w sieci
Obsługuje Full Duplex Flow Control (zgodnie ze standardem IEEE
802.3x)
Zintegrowany terminal nadawczo-odbiórczy 10/100/1000
Obsluguje 32 bitowe PCI w wersji 2.3 o częstotliwościach 33/66-MHz
Detekcja Crossover i autokorekcja
Obsługuje Wake-on-LAN i zdalne wake-up
1394a FireWire (opcjonalnie)
•
•
W pełni zgodna z zabezpieczeniem standardu IEEE 1394-1995 dla wysokiej
wydajności szyny szeregowej oraz standardu IEEE 1394a-2000
Dwa złącza całkowicie zgodne ze standardem IEEE 1394a-2000 o szybkości
przesyłania 400M bits/s
Możliwości rozbudowy
Płyta głwna wyposażona jest w następujące gniazda:
•
Jedno gniazdo PCI Express x16 dla karty graficznej
•
Dwa gniazda typu PCI Express x1
•
Trzy 32-bitowych gniazda zgodnych z PCI w wersji 2.3
•
Dwa 40-nóżkowe złącza IDE mogące obsłużyć do czterech urządzeń IDE
•
Jedno złącze obsługujące stacje dyskietek
•
Cztery 7-nóżkowe złącza SATA
Płyta główna obsługuje szynę UltraDMA z szybkością transferu 133/100/66/33 MB/s.
Zintegrowane We/Wy
Polski
Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:
•
Dwa gniazda PS/2 dla myszy i klawiatury
•
Jedno gniazdo szeregowe
•
Jedno gniazdo równoległe
•
Cztery gniazda USB
•
Jedno gniazdo 1394a (opcjonalnie)
•
Jedno gniazdo LAN (opcjonalnie)
•
Gniazda audio typu jack wejście dla mikrofonu, gniazdo wejściowe i
wyjściowe audio, 8 kanałów.
Firmowy BIOS
Płyta głwna wyposażona jest w BIOS firmy AWARD, który pozwala użytkownikowi
konfigurować wiele cech systemu włączając w to następujące właściwości:
•
Zarządzanie poborem mocy
•
Alarmy typu Wake-up
•
Parametry pracy procesora
•
Ustalenia szybkoœci pracy procesora i pamiêci
BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara
procesora.
Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie
bez uprzedniego powiadomienia.
Multi-Language Translation
Vlastnosti
Procesor
Základní deska RX480–A využívá 939kolíkovou patici nabízející následující vlastnosti:
•
Podpora procesorů AMD Sempron/Athlon64/Athlon 64 FX
•
Podpora rychlostí rozhraní HyperTransportTM (HT) až 2000 MT/s
Technologie HyperTransport TM je přímým spojením mezi dvěma zařízeními, umožňující
integrovaným obvodům výměnu informací vyššími rychlostmi, než jaké nabízejí současné
technologie.
Čipová sada
Čipy northbridge (NB) RX480 a southbridge (SB) SB400 jsou založeny na inovativní a
škálovatelné architektuře s ověřenou spolehlivostí a výkonností.
RX480 (NB)
•
•
•
•
SB400 (NB)
•
•
•
•
•
Paměť
Paměti DDR 400/333/266 DDR SDRAM s dvoukanálovým přenosem
Podpora ctyři modulů DIMM bez vyrovnávací paměti s maximální
kapacitou 4 GB
Zvuk (volitelné)
Tato základní deska může podporovat některou z následujících zvukových čipových
sad:
•
•
•
•
•
•
•
Splňuje požadavky standardu AC’97 2.3
16bitový stereo plnì duplexní kodek se vzorkovací frekvencí 48 MHz
Podpora dvojnásobné vzorkovací frekvence (96 kHz) pro přehrávání
DVD audio
Kompatibilita s Direct Sound 3DTM
Splňuje požadavky standardu AC’97 2.3, podpora 8kanálového D/A
převodníku
Splňuje výkonnostní požadavky pro audio zařízení na systémech
PC99/2001
Splňuje požadavky pro audio zařízení Microsoft WHQL/WLP 2.0
Multi-Language Translation
Česky
•
•
1 x2 (rozšířitelné až na x4) rozhraní A–Link Express (splňuje
požadavky standardu PCI Express 1.0a) pro připojení k ATI IXP
Podpora jednoho rozhraní PCI Express x16 pro grafiku, zcela
splňující základní požadavky standardu PCI Express, revize
1.0a.
Plná podpora ACPI stavy S1, S3, S4 a S5.
Podpora řešení v jediném čipu s technologií 0,13 mikronů, 1,0–1,2
V CMOS
2/4kanálové rozhraní A–Link Express (splňuje požadavky standardu PCI Express 1.0a) pro RADEON IGP
Splňuje požadavky standardu PCI 2.3 s podporou až 7 hlavních
kanálů
Podpora čtyř sériových rozhraní ATA, splňuje požadavky standardu Serial ATA 1.0, součástí jsou řadiče RAID 0 a RAID 1
Integrované hostitelské řadiče USB 2.0 podporující až osm
portů
Integrovaný řadič IDE podporující Ultra ATA s režimy 133/100
/66/33
Vestavění síťové rozhraní LAN (volitelně)
Vestavěné síťové rozhraní LAN nabízí následující možnosti:
•
Podpora 10/100Mbps N–cestného automatického přepínání provozu
•
Podpora funkce Wake–On–LAN a aktivace na dálku
•
Podpora kolíků LED pro různou indikaci síťové činnosti
•
Podpora plně duplexního řízení toku dat (IEEE 802.3x)
•
•
•
•
Integrovaný transceiver 10/100/1000
Podpora rozhraní PCI v2.3, 32bitové, 33/66 MHz
Detekce přeslechu a automatická korekce
Podpora funkce Wake–on–LAN (WOL) a vzdálené aktivace
1394a FireWire (volitelné)
•
•
Plná podpora standardu IEEE 1394–1995 pro vysokovýkonnou sériovou
sběrnici a IEEE standard 1394a–2000
Dva kabelové porty podle standardu IEEE 1394a–2000 s rychlostí až 400
Mb/s
Možnosti rozšíření
Základní deska je dodávána s následujícími možnostmi rozšíření
•
Jedna patice PCI Express x16 pro grafickou kartu
•
Dvě patice PCI Express x1
•
Tři 32bitové patice PCI v2.3
•
Dva 40kolíkový konektor IDE podporující až čtyři zařízení IDE
•
Jedno rozraní pro disketovou mechaniku
•
Čtyři 7kolíkové konektor SATA
Základní deska podporuje sběrnici Ultra DMA s přenosovými rychlostmi 133/100/66/33
MB/s.
Integrovaný vstup/výstup
Česky
Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:
•
Dva porty PS/2 pro myš a klávesnici
•
Jeden sériový port
•
Jeden paralelní port
•
Čtyři USB porty
•
Jeden port 1394a (volitelně)
•
Jeden port LAN (volitelně)
•
Zvukové konektory pro mikrofon, zvukový vstup a 8kanálový zvukový
výstup
Firmware BIOS
Základní deska využívá BIOS formy AWARD, který uživateli umožňuje nakonfigurovat
mnoho systémových parametrů, včetně následujících:
•
Řízení spotřeby
•
Alarmy při spouštění systému
•
Parametry CPU
•
Časování CPU a paměti
Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence
procesoru.
Některé technické parametry hardware a software se mohou měnit bez
předchozího upozornění.
Multi-Language Translation
Caracteristici
Procesorul
RX480-A utilizează un soclu de 939 de ace care are următoarele caracteristici:
•
Funcţionează cu procesoare AMD Sempron/Athlon64/Athlon 64 FX
•
Suportă interfeţe HyperTransportTM (HT) cu viteze de până la 2000 MT/s
Tehnologia HyperTransportTM este o legătură punct-la-punct între două aparate, care permite
viteze mult mai mari de schimb al informaţiilor între circuitele integrate, decât cel asigurat de
tehnologiile de interconectare actuale.
Setul de chipuri
Seturile de chipuri RX480 Northbridge (NB) şi SB400 Southbridge (SB) se bazează pe o
arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi performanţă.
RX480 (NB)
•
O interfaţă x2 (extensibil la x4) A-Link Express (compatibilă cu
PCI Express 1.0a) pentru conectare la ATI IXP
Suportă o interfaţă grafică PCI Express x16, pe deplin compatibil
cu specificaţia de bază PCI Express, versiunea 1.0a.
Suportă complet stările ACPI S1, S3, S4 şi S5.
Suportă soluţia cu un singur cip pentru tehnologia CMOS pe
0,13 microni, la 1,0–1,2 V
•
•
•
SB400 (SB)
•
Interfaţă A-Link Express cu 2/4 magistrale (compatibilă cu PCI
Express 1.0a) pentru IGP-uri RADEON
Compatibilă cu specificaţia PCI 2.3, suportând până la 7 unităţi
bus master
Suportă patru unităţi Serial ATA, compatibilă cu specificaţia Serial
ATA 1.0, RAID 0 şi RAID 1 incorporat
Controler gazdă USB 2.0, suportând până la opt porturi USB
2.0
Controler IDE integrat care suportă modurile Ultra DMA
133/100/66/33
•
•
•
•
Memoria
•
•
Suport DDR 400/333/266 DDR SDRAM cu canal dual
Funcţionează cu patru module fără zonă tampon DIMM, cu capacitate
maximă de 4 GB
Audio(opţional)
•
•
•
•
•
•
•
Compatibil cu specificaţia AC’97 2.3
CODEC de 16 biţi stereo cu duplex complet şi viteză de eşantionare de
48 MHz
Suport pentru viteză dublă de eşantionare (96 kHz) pentru redare audio
de pe DVD
Compatibil cu Direct Sound 3DTM
Compatibilitate cu AC’97 specificaţia 2.3, suportând DAC-uri cu 8 canale
Corespunde cerinţelor de performanţă audio pentru sisteme PC99/2001
Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0
Multi-Language Translation
Română
Audio are următoarele caracteristici:
Onboard LAN (opţional)
Onboard LAN are următoarele caracteristici:
•
•
•
•
Suportă operaţii de autonegociere N-way de 10/100 Mbps
Suportă funcţia Wake-On-LAN şi trezirea de la distanţă
Suportă ace LED pentru a indica diversele activităţi din reţea
Suportă controlul proceselor de duplex total (IEEE 802.3x)
•
•
•
•
Unitate de emisie/recepţie 10/100/1000 integrat
Suportă PCI, versiunea 2.3, de 32 biţi, la 33/66 MHz
Detectare tranziţie şi corectare automată
Suport pentru funcţiile Wake-on-LAN şi trezire la distanţă
1394a Fire Wire (opţional)
•
•
Compatibil deplin cu prevederile standardului IEEE 1394-1995, oferind un
bus serial de înaltă performanţă şi compatibilitate cu standardul IEEE 1394a2000
Două porturi de cablu compatibile deplin cu standardul IEEE 1394a-2000 ,
la viteza de 400 Mb/s
Opţiuni de extindere
Placa de bază este dotată următoarele posibilităţi de extindere:
•
Un PCI Express de 16x pentru interfaţa grafică
•
Două sloturi PCI Express x1
•
Trei sloturi de 32 biţi compatibile PCI, versiunea 2.3
•
Două conectoare IDE 40 cu care suport cel mult 4 instrumente IDE
•
O interfaţă pentru unitate floppy
•
Patru conectoare SATA 7
Placa de bază suportă bus mastering UltraDMA cu viteze de transfer de 133/100/66/33 MB/s
I/O integrată
Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:
•
Două porturi PS/2, pentru mouse şi tastatură
•
Un port serial
•
Un port paralel
•
Patru porturi USB
•
Un port 1394a (opţional)
•
Un port LAN (opţional)
•
Mufe audio pentru microfon, intrare audio şi ieşire audio cu 8 canale
Română
Firmware BIOS
Placa de bază utilizează AWARD BIOS, care permite utilizatorului să configureze mai mulţi
parametri ai sistemului, cum ar fi:
•
Gestionarea energiei
•
Alarme de trezire
•
Parametri CPU
•
Temporizare CPU şi memorie
Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă
ale procesorului.
Anumite specificaţii hardware şi elemente de software pot fi modificate fără
înştiinţare prealabilă.
Multi-Language Translation
Спецификация
Процесор
RX480-A използва сокет 939-pin със следните спецификации:
•
Поддръжка на процесори AMD Sempron/Athlon64/Athlon 64 FX
•
Поддръжка на технологията HyperTransport TM (HT) със скорост до
2000MT/s
Технологията HyperTransport TM е връзка точка-до-точка (point-to-point) между
две устройства, която предоставя възможност интегрираните вериги да обменят
информация на много по-висока скорост от досегашно съществуващите технологии.
Чипсет
Чипсетът със северен мост RX480 (NB) и южен мост SB400 (SB) е изграден на базата
на оригинална архитектура с възможност за надстройка с доказана надеждност и
производителност.
•
Интерфейс A-Link Express x2 с възможност за разширение до
RX480 (NB)
x4 (съвместим с PCI Express 1.0a) за връзка към ATI IXP
Графичен интерфейс PCI Express x16 напълно съвместим
със спецификацията PCI Express Base 1.0a.
Пълна поддръжка на ACPI (Advanced Configuration and
Power Interface), режими S1, S3, S4 и S5.
Поддръжка на CMOS технология на един чип 0.13 микрона,
1.0-1.2v
•
•
•
S400 (SB)
•
2/4-канален интерфейс A-Link Express (съвместим с PCI
Express 1.0a) за връзка към RADEON IGP
Съвместимост със спецификацията PCI 2.3 с поддръжка на
до 7 bus master устройства
Поддръжка на четири устройства Serial ATA, съвместимо със
спецификацията Serial ATA 1.0, поддръжка на RAID 0 и RAID
1
Интегриран контролер USB 2.0 с поддръжка до осем порта
USB 2.0
Интегриран IDE контролер Ultra DMA 133/100/66/33
•
•
•
•
Памет
•
•
Поддръжка на двуканална памет DDR 400/333/266 DDR SDRAM
Поддръжка на четири небуферирани слота DIMM с общ максимален
капацитет 4 GB
Аудио (опция)
•
•
•
•
•
•
•
Съвместимост със спецификацията AC’97 2.3
16-bit Stereo full-duplex CODEC с честота 48MHz
Поддръжка на двойна честота (96KHz) при възпроизвеждане на
DVD audio
съвместимост с Direct Sound 3DTM
Съвместимост със спецификацията AC’97 2.3, с поддръжка на 8канални цифрово-аналогови преобразователи
Съответствие с изискванията за аудио производителност на
системи PC99/2001
Съответствие с изискванията на Microsoft WHQL/WLP 2.0
Multi-Language Translation
Български
Тази дънна платка може да поддържа един от следните видове аудио чипсети
Интегриран мрежов контролер (опция)
Спецификация на интегрирания мрежов контролер:
•
•
•
•
поддръжка на 10/100Mbps, N-Way Auto-negotiation operation
поддръжка на функция за “събуждане” Wake-On-LAN и дистанционен
wake-up
LED-индикатори за мрежова активност
поддръжка на Full Duplex Flow Control (IEEE 802.3x)
•
•
•
•
Интегриран 10/100/1000 контролер
поддръжка на PCI v2.3, 32-bit, 33/66-MHz
Автоматично разпознаване и конфигурация
Поддръжка на функции Wake-on-LAN и remote wake-up
1394a FireWire контролер (опция)
•
•
Пълна съвместимост със стандартите IEEE 1394 -1995 за високоскоростна
серийна шина и IEEE 1394a -2000
Два кабелни порта (400M bits/s) напълно съвместими със стандарта IEEE
1394a-2000
Възможности за разширяване
Дънната платка има следните разширителни възможности:
•
един слот PCI Express x16 за графичен интерфейс
•
Два слота PCI Express x1
•
три слота 32-bit PCI v2.3
•
Два колектора 40-pin IDE с поддръжка на четири IDE устройства
•
един конектор за флопидисково устройство
•
четири 7-щифтови SATA конектораs
Дънната платка поддържа шина UltraDMA 133/100/66/33 MB/s
Интегриран Вход/Изход контролер
Дънната платка има пълен набор от I/O портове и конектори:
•
два PS/2 порта за мишка и клавиатура
•
един сериен порт
•
един паралелен порт
•
четири USB портa
•
един 1394a порт (опция)
•
един LAN порт (опция)
•
Аудио гнезда за микрофон, линеен вход и 8-канален аудио изход
BIOS Firmware
Български
Дънната платка използва AWARD BIOS с възможност за различни системни настройки,
включително
•
управление на захранването
•
Wake-up аларми
•
параметри на процесора
•
синхронизиране на процесора и паметта
настройка на скоростта на часовника на процесора
Хардуерните и софтуерни спецификации и параметри могат да бъдат
изменени без предупреждение.
Multi-Language Translation
Jellemző
Processzor
Az RX480-A 939 tűs foglalattal rendelkezik, ennek jellemzői pedig a következők:
•
AMD Sempron/Athlon64/Athlon 64 FX processzorokkal működik
•
Maximum 2000 MT/s HyperTransportTM (HT) sebességű interfészt támogat
A HyperTransportTM technológia egy ponttól pontig való kapcsolat két készülék között, és
segítségével az integrált áramkörök közötti információcsere sebessége sokkal nagyobb, mint a
jelenleg rendelkezésre álló összekapcsolási technológiák esetében.
Lapkakészlet
A RX480 Northbridge (NB) és SB400 Southbridge (SB) lapkakészletek egy új és méretezhető,
nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.
RX480 (NB)
•
•
•
•
SB400 (SB)
•
•
•
•
•
Egy 2-szeres (4-szeresre bõvíthetõ) A-Link Express interfész (PCI
Express 1.0a kompatibilis) az ATI IXP kapcsolására
Egy 16-szoros PCI Express a grafikus interfész számára, amely teljesen kompatibilis a PCI Express alapspecifikáció 1.0a változatával.
Teljesen mértékben támogatja az S1, S3, S4 és S5 ACPI állapotokat.
Egylapkás megoldást is támogat 0,13 mikronos, 1,0-1,2 V-os CMOS
technológiával
2/4 sávos A-Link Express (PCI Express 1.0a kompatibilitású) interfész
a RADEON IGP-khez
A PCI 2.3-as specifikációjával kompatibilis, akár 7 bus master eszközt
támogat
Négy soros ATA eszközt támogat, kompatibilis a soros ATA 1.0
specifikációjával, RAID 0 és RAID 1 beépítve
Beépített USB 2.0 gazda vezérlõ, legtöbb nyolc USB 2.0 portot
támogat
Beépített IDE vezérlõ, amely az Ultra DMA 133/100/66/33 módokat
támogatja
Memória
•
•
DDR 400/333/266 DDR SDRAM, duál csatorna támogatásával
Négy puffer nélküli DIMM, maximum 4 GB-os memóriakapacitással
Audio (opcionális)
Az alaplapon levő Audio jellemzői:
•
•
•
•
•
Megfelel az AC’97 2.3-as specifikációnak
16 bites sztereo teljes duplex CODEC 48 MHz-es mintavételezési
sebsséggel
Dupla mintavételezési arányú (96 kHz) DVD audio lejátszást teszt
lehetővé
Kompatibilis a Direct Sound 3DTM technológiával
Kompatibilis az AC’97 2.3-as specifikációval, 8 csatornás DAC-t támogatva.
Megfelel a PC99/2001 rendszerek audio-teljesítménnyel szembeni
követelményeknek
Megfelel a Microsoft WHQL/WLP 2.0 audio követelményeine
Multi-Language Translation
Magyar
•
•
Alaplapon levő LAN (választható)
Az alaplapon levő LAN jellemzői:
•
•
•
•
10/100Mbps N-Way automatikus beállítással
Támogatja a Wake-On-LAN funkciót és a távoli ébresztést
LED csatlakozótűket támogat különféle hálózati tevékenység-kijelzõk
számára
Támogatja a teljes duplex folyamatvezérlést (IEEE 802.3x)
•
•
•
•
Integrált 10/100/1000 adó-vevő
Támogatja a 32 bites, 33/66 MHz-es PCI 2.3-as változatát
Rendszerváltás érzékelés és automatikus javítás
A Wake-on-LAN és a távoli ébresztés funkciók támogatása
1394a FireWire (opcionális)
•
•
Teljesen kompatibilis az IEEE 1394-1995 szabvány elõírásaival,
csúcsteljesítményű soros busszal, és megfelel az IEEE 1394a-2000
szabványnak
Két, az IEEE 1394a-2000 szabvánnyal teljesen kompatibilis kábelportok,
400 Mbit/s sebességen
Bővítési lehetőségek
Az alaplap a következő bővítési lehetőségekkel rendelkezik:
•
Egy 16-szoros PCI Express a grafikus interfész számára
•
Két 1-szeres PCI Express foglalat
•
Három 32 bites, a PCI 2.3-as változatával kompatibilis foglalat
•
Két 40 tűs IDE csatlakozó négy IDE eszköz támogatására
•
Egy hajlékonylemez meghajtó interfész
•
Négy 7 tűs SATA csatlakozó
Az alaplap támogatja az UltraDMA bus mastering megoldást, 133/100/66/33 MB/s sebességen
Beépített I/O
Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:
•
Két PS/2 port az egér és a billentyűzet számára
•
Egy soros port
•
Egy párhuzamos port
•
Négy USB port
•
Egy 1394a port (választható)
•
Egy LAN port (választható)
•
Audio csatlakozók mikrofon bemenethez, audio bemenethez és 8 csatornás
audio kimenethez
BIOS Firmware
Magyar
Az alaplapon levő AWARD BIOS segítségével a felhasználó a rendszer sok paraméterét
állíthatja be, például:
•
Energiagazdálkodás
•
Ébresztési riasztások
•
CPU paraméterek
•
CPU és memória időzítés
A firmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.
Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül
módosulhatnak.
Multi-Language Translation