Culligan Mark 100 Operating instructions

Cat. No. 01-8822-21
Rev. A 03-16-00
DCO # 200
Installation
and
Operating
Instructions
CULLIGAN®
MARK 100
AUTOMATIC
WATER CONDITIONER
MODELS FROM 2000
©2000 Culligan International Company
Printed in USA
Attention Culligan Customer:
The installation, service and maintenance of this equipment should be
rendered by a qualified and trained service technician. Your local independently operated Culligan dealer employs trained service and maintenance personnel who are experienced in the installation, function and repair of Culligan equipment. This publication is written specifically for
these individuals and is intended for their use.
We encourage Culligan users to learn about Culligan products, but we
believe that product knowledge is best obtained by consulting with your
Culligan dealer. Untrained individuals who use this manual assume the
risk of any resulting property damage or personal injury.
WARNING - Prior to servicing equipment, disconnect power
supply to prevent electrical shock.
WARNING - If incorrectly installed, operated or maintained,
this product can cause severe injury. Those who install, operate, or
maintain this product should be trained in its proper use, warned of
its dangers, and should read the entire manual before attempting to
install, operate or maintain this product.
I F T H I S E Q U I P M E N T I S TO B E U S E D I N T H E T R E ATMENT OF DRINKING WATER, THE WATER MUST BE MIC R O B I O L O G I C A L LY S A F E .
Installation
and
Operating
Instructions
CULLIGAN®
MARK 100
AUTOMATIC
WATER CONDITIONER
MODELS FROM 2000
Table of Contents
Page
Introduction ............................................................... 2
Specifications ........................................................... 3
Preparation ............................................................... 4
Installation ................................................................ 6
Settings .................................................................. 12
Programming .......................................................... 15
Manual Cycling ....................................................... 19
Service Check ........................................................ 20
Operation ................................................................ 21
Sanitizing Instructions ............................................. 23
Parts List ................................................................ 24
Introduction
The Culligan® Mark 100 water softeners are tested and validated by WQA against ANSI/NSF
Standard 44 for the effective reduction of calcium and magnesium along with Barium and
Radium 226/228*.
SAFE PRACTICES
Throughout this manual there are paragraphs set off by special headings.
NOTICE: Notice is used to emphasize installation, operation or maintenance information which is important, but
does not present any hazard.
Example: NOTICE: The nipple must extend no more than 1 inch above the cover plate.
CAUTION: Caution is used when failure to follow directions could result in damage to equipment or
property. Example:
CAUTION: Disassembly while under water pressure can result in flooding.
WARNING: Warning is used to indicate a hazard which could cause injury or death if ignored. Example:
WARNING! ELECTRICAL SHOCK HAZARD! UNPLUG THE UNIT BEFORE
REMOVING THE COVER OR ACCESSING ANY INTERNAL CONTROL PARTS.
SERIAL NUMBERS
The control valve serial number is located on the back of the timer case.
The media tank serial number is located on the top surface of the tank.
NOTICE: Do not remove or destroy the serial number. It must be referenced on request for warranty repair or
replacement.
This publication is based on information available when approved for printing. Continuing design refinement
could cause changes that may not be included in this publication.
2
CULLIGAN® MARK 100 WATER SOFTENER
* Verified utilizing hardness surrogate per ANSI/NSF Standard 44.
Specifications
Culligan® Mark 100 Water Conditioners with Time Clock, Aqua-Sensor® Device or Soft-Minder® Meter
Control Valve
Overall Conditioner Height
Media Tank Dimensions (Dia x Ht)
Salt Storage Tank Dimensions (Dia x Ht)
Exchange Media, Type and Quantity
Underbedding, Type and Quantity
Exchange Capacity
@ Salt Dosage Per Recharge1
Freeboard to Media2
Freeboard to Underbedding3
Salt Storage Capacity
Rated Service Flow @ Pressure Drop
Total Hardness, Maximum
Total Iron, Maximum
Hardness to Iron Ratio, Minimum
Operating Pressure
Operating Temperature
Electrical Requirements
Electrical Power Consumption, Min/Max
Drain Flow, Maximum4
Recharge Time, Average5
Recharge Water Consumption, Average
1
2
3
4
5
9” Model
5-cycle, Reinforced Thermoplastic
51 in
1 295 mm
9 x 45 in
229 x 1 143 mm
16 x 43 in
406 x 1 092 mm
18 x 43 in
457 x 1092 mm
Cullex® Media, 0.86 ft3
Cullex® Media, 24.5 L
Cullsan® Underbedding, 12 lb
Cullsan® Underbedding, 5.4 kg
17,500 gr @ 4.0 lb
1 133 g @ 1.8 kg
23,900 gr @ 8.0 lb
1 547 g @ 3.6 kg
26,600 gr @ 12.0 lb
1 722 g @ 5.4 kg
16.6-17.6 in
420-447 mm
39.2 in
996 mm
250 lb or 375 lb
114 kg or 170 kg
7.5 gpm @ 15 psi
30 Lpm @ 102 kPa
75 gpg
1 283 mg/L
5 ppm
5 mg/L
8 gpg to 1 ppm
140 mg/L to 1 mg/L
20-125 psi
140-860 kPa
33-120°F
1-50°C
120V/60 Hz
3 Watts/35 Watts
2.0 gpm
8 Lpm
80 min
45 gal
170 L
12” Model
5-cycle, Reinforced Thermoplastic
51 in
1 295 mm
12 x 45 in
305 x 1 143 mm
18 x 43 in
457 x 1 092 mm
Cullex® Media, 1.4 ft3
Cullex® Media, 40 L
Cullsan® Underbedding, 30 lb
Cullsan® Underbedding, 14 kg
24,100 gr @ 6.0 lb
1 560 g @ 2.7 kg
34,500 gr @ 12.0 lb
2 234 g @ 5.4 kg
41,900 gr @ 18.0 lb
2 713 g @ 8.1 kg
17.5-18.5 in
444-470 mm
38.5 in
978 mm
375 lb
170 kg
7.5 gpm @ 15 psi
31 Lpm @ 102 kPa
99 gpg
1 692 mg/L
5 ppm
5 mg/L
8 gpg to 1 ppm
140 mg/L to 1 mg/L
20-125 psi
140-860 kPa
33-120°F
1-50°C
120V/60 Hz
3 Watts/35 Watts
3.5 gpm
14 Lpm
85 min
86 gal
325 L
Capacities and corresponding salt dosages pertain to low hardness waters. Capacities given are per recharge
Measured from top of media to top of inlet fitting (backwashed and drained).
Measured from top of underbedding to top of inlet fitting.
Backwash at 120 psi (830 kPa).
10 minute backwash, 7 lb (3.2 kg) 9” model or 13 lb (5.9 kg) 12” model salt dosage at 30 psi (204 kPa).
SPECIFICATIONS
3
Preparation
COMPONENT DESCRIPTION
The water conditioner is shipped from the factory in a minimum of four cartons. Remove all components from
their cartons and inspect them before starting installation.
Control Valve Assembly - Includes the 5-cycle regeneration control valve and the Accusoft® Microprocessor.
Small parts packages will contain additional installation hardware. Installation and Operations Instructions and an
Owner’s Guide are included.
Media Tank - Includes Tripl-Hull™ media tank complete with Cullex® ion exchange resin, underbedding and
outlet manifold.
Salt Storage Tank Assembly - Includes salt storage container with support plate and Dubl-Safe™ brine refill
valve and chamber.
Bypass Valve - Includes the Cul-Flo-Valv®, interconnecting couplings, and the screws necessary for assembly.
TOOLS AND MATERIALS
The following tools and supplies will be needed, depending on installation method. Observe all applicable codes.
All Installations
• Safety glasses
• Phillips screwdrivers, small and medium tip.
• Gauge assembly (PN 00-3044-50 or equivalent)
• Silicone lubricant (PN 00-4715-07 or equivalent) - DO NOT USE PETROLEUM-BASED LUBRICANTS
• A bucket, preferably light-colored
• Towels
Special Tools
• Torch, solder and flux for sweat copper connections
• Threading tools, pipe wrenches and thread sealer for threaded connections.
• Saw, solvent and cement for plastic pipe connections.
Materials
• Brine line, 5/16” (PN 00-3031-28 or equivalent)
• Drain line, 1/2” (PN 00-3030-82, gray, semi-flexible; or PN 00-3319-46, black, semi-rigid; or equivalent)
• Thread sealing tape
• Pressure reducing valve (if pressure exceeds 125 psi [860 kPa], PN 00-4909-00 or equivalent)
• Pipe and fittings suited to the type of installation
• Water softener salt (rock, solar or pellet salt formulated specifically for water softeners)
APPLICATION
Water quality - Verify that raw water hardness and iron are within limits. Note the hardness for setting the salt
dosage and recharge frequency.
Pressure - If pressure exceeds 125 psi (860 kPa), install a pressure reducing valve (see materials checklist). On
private water systems, make sure the minimum pressure (the pressure at which the pump starts) is greater than 20
psi (140 kPa). Adjust the pressure switch if necessary.
CAUTION: The use of a pressure reducing valve may limit the flow of water
in the household.
4
CULLIGAN® MARK 100 WATER SOFTENER
Temperature - Do not install the unit where it might freeze, or next to a water heater or furnace or in direct
sunlight.
LOCATION
Space requirements - Allow 6-12 inches (15-30 cm) behind the unit for plumbing and drain lines and 4 feet (1.3
meters) above for service access and filling the salt container.
Floor surface - Choose an area with solid, level floor free of bumps or irregularities. Bumps, cracks, stones and
other irregularities can cause the salt storage tank bottom to crack when filled with salt and water.
Drain facilities - Choose a nearby drain that can handle the rated drain flow (floor drain, sink or stand pipe). Refer
to the Drain Line Chart, Table 1 (page 10), for maximum drain line length.
NOTICE: Most codes require an anti-siphon device or airgap. Observe all local plumbing codes and drain
restrictions. The system and installation must comply with all state and local laws and regulations.
Electrical facilities - A 10-foot cord and wall mount plug-in transformer are provided. The customer should provide a receptacle, preferably one not controlled by a switch that can be turned off accidentally. Observe local
electrical codes.
PREPARATION
5
Installation
PLACEMENT
Refer to Figure 1 for system placement.
• Set the media tank on a solid, level surface near water, drain and electrical facilities. Place the outlet (black
coupling) of the tank on the left.
• Set the brine system on a flat, smooth, solid surface as near the media tank as possible.
MOUNT THE CONTROL VALVE
See Figure 2 for a visual on mounting the control valve to the tank.
• Remove and discard the protective covers on the tank couplings.
• Lubricate the o-rings on the tank couplings with silicone lubricant.
• Place the control on the tank couplings and press down firmly.
NOTICE: The white tank coupling is the inlet, and should be located on the inlet side (right side) of the control.
• Install the u-clamps on both sides of the control and secure with the screws.
TWELVE INCH SOFTENERS
As shipped from the factory, each control is equipped as a 9-inch unit. A 12-inch eductor nozzle and backwash
flow control are included with each unit for conversion for use with the 12-inch tanks.
NOTICE: To prevent injury, convert unit to a twelve-inch configuration prior to installation.
Refer to Figure 3 for a visual on changing the eductor nozzle and the backwash flow control.
Eductor Nozzle Replacement:
• Remove the three screws on the eductor cap and remove the cap.
• Remove the eductor assembly.
• Remove the eductor screen from the assembly
• Remove the blue nozzle and replace it with the beige nozzle. Make sure to put the o-ring on the beige
nozzle.
• Reverse the procedure to reassemble. To prevent leaks, ensure that the gasket is in the proper position.
Backwash Flow Control Replacement:
• Remove the drain clip and pull the drain elbow straight off.
• Remove the backwash flow control located behind the elbow. Put the #3 restrictor in its place.
NOTICE: The number on the flow control should face into the valve body.
• Reverse the procedure to reassemble.
T re a te d W a te r O u t
To
H o se
B ib s
D ra in L in e
H a rd W a te r In
H e a te r
S o fte n e r
FIGURE 1
6
CULLIGAN® MARK 100 WATER SOFTENER
B rin e T a n k
W a te r
M e te r
or
Pum p
FIGURE 2
FIGURE 3
PLUMBING CONNECTIONS
Two methods of connecting the water softener to the plumbing system are available. Shipped with each softener
is a Culligan® Cul-Flo-Valv® bypass valve, either PN 01-0124-88 or 01-0102-38. If local conditions warrant,
you may use the sweat adaptor kits, PN 00-3314-44 or 00-3314-45.
NOTICE: The Soft-Minder® meter cannot be used with the sweat adaptors.
CAUTION: Close the inlet supply line and relieve system pressure before
cutting into the plumbing! Flooding could result!
CAUTION: When making sweat connections, remove all plastic and rubber
components which contact brass or copper. Damage to these components may
result otherwise.
BYPASS VALVE INSTALLATION
AQUA-SENSOR ® SENSING DEVICE AND TIME CLOCK UNITS ONLY
The bypass valve connects directly to the backplate of the valve with a pair of couplings and screws (Figure 4). To
facilitate this connection, remove the plate by pulling up on the u-clip on the back of the valve. Lubricate all o-rings
with silicone lubricant.
BYPASS VALVE INSTALLATION
SOFT-MINDER ® METER ONLY
The Soft-Minder meter is placed between the bypass valve and the control in place of the couplings shipped with
the Cul-Flo-Valv® (Figure 5). Make sure the meter is on the outlet port of the control and that it is installed with the
arrow pointing in the direction of water flow. A pair of elongated bolts are packaged with the meter to hold the
bypass valve to the back plate of the control. Lubricate all o-rings with silicone lubricant.
SWEAT ADAPTOR INSTALLATION
The sweat adaptors use a snap ring to hold them to the backplate of the control valve. The back plate will need to
be removed from the valve for this connection. A pair of snap ring pliers, PN 00-5916-09, are needed for this
connection.
INSTALLATION
7
FIGURE 4
FIGURE 5
CAUTION: When reinstalling back plate to control valve, make sure the u-clip
fully engages the two bottom holes of the bracket (Figure 6). Secure bracket from
the top with the two mounting screws provided.
CONNECT THE BRINE LINE
Refer to Figures 6 & 7.
• Use the length of brine line included in the
brine tank, or measure a length of brine line
sufficient to reach from the brine tank to the
brine fitting, with no sharp bends. For easier
access to the float it is recommended to add an
extra four feet (1.3 meters) of length to the brine
line. Cut both ends of the brine line squarely
and cleanly.
• Remove the brine valve from the brine tank
and then remove the white nut and insert from
the float rod. Return float rod to its original position.
FIGURE 6
• Slip the white nut over one end of the tubing
and press the plastic insert into the end of the
tubing (Figure 7). Connect to the brine valve
and tighten nut.
• Remove white nut from the brine connection,
and remove the plastic insert from the brine
connection fitting.
• Slip the white nut over one end of the tubing
and press the plastic insert into the end of the
tubing (Figure 7). Connect to the brine connection on the valve and tighten nut (Figure 6).
8
CULLIGAN® MARK 100 WATER SOFTENER
FIGURE 7
DRAIN LINE CONNECTION
Refer to Table 1, page 10 under the applicable tank size for drain line length and height limitations, and to Figure
3.
•
•
•
•
Remove 1/2” pipe clamp from the small parts pack included with the control.
Route a length of 1/2” drain line from the drain elbow to the drain.
Fasten the drain line to the elbow with the clamp.
Secure the drain line to prevent its movement during regeneration. When discharging into a sink, or open floor
drain, a loop in the end of the tube will keep it filled with water and will reduce splashing at the beginning of each
regeneration.
NOTICE: Waste connections or drain outlets shall be designed and constructed to provide for connection to the
sanitary waste system through an air gap of 2 pipe diameters or 1 inch, whichever is larger.
NOTICE: Observe all plumbing codes. Most codes require an anti-siphon device or air gap at the discharge
point. The system and installation must comply with state and local laws and regulations.
FILL THE SALT STORAGE CONTAINER
Fill the salt storage container with water until the level reaches about 1 inch above the salt support plate. Pour salt
into the container. Fill with salt to within a few inches of the top.
AQUA-SENSOR ® PROBE AND SOFT-MINDER ® METER CONNECTION
To connect the probe or meter leads refer to Figure 8 and proceed as follows:
•
•
•
•
Remove the timer case from the back plate by removing the two screws on the front of the cover.
Rotate the circuit board holding plate to provide access to the back of the circuit board.
Remove the plastic plug from the backplate.
Slip the sensor probe lead or meter cable through the hole and toward the circuit board.
NOTICE: The strain relief located on the back of the wire connection for the Aqua-Sensor® probe may have to be
removed in order to fit it through the backplate. Replace the strain relief if you need to remove it for assembly.
• Connect the lead to the circuit board. The Aqua-Sensor® probe terminal is labeled "AQUA" while the SoftMinder® meter terminal is labeled "METER".
• Pull any excess cable wire back out of the enclosure, and route the wiring inside the enclosure to avoid any
interference with moving parts.
• Locate the strain relief bushing in the parts pack. Place it on the cable at the point of entry to the rear of the timer
plate and push it into the hole.
NOTICE: The wire connectors must be
connected to the circuit board properly.
The wires must exit the plug-in connector opposite of the raised white base of
the circuit board connector. Failure to
properly connect any of the connectors
will result in a malfunction of the circuit
board operation.
FIGURE 8
INSTALLATION
9
ELECTRICAL CONNECTION
The power cord needs to be connected to the plug-in transformer. Figure 9 shows the cord attachment to the transformer.
NOTICE: Observe all state and local electrical codes.
FIGURE 9
FRONT COVER ATTACHMENT
The front door comes in protective wrap to prevent damage during shipment. The wrap also keeps the door free of
fingerprints and other marks. The door should be assembled to the control as a final step, when you are finished with
the installation. There are two small clips in the small parts pack which are used to secure the door to the valve
cover. Figure 10 shows how the clips snap into the cover to hold the door.
FIGURE 10
10 CULLIGAN® MARK 100 WATER SOFTENER
TABLE 1 - DRIAN LINE LENGTH AND HEIGHT LIMITATIONS
9-INCH MODELS
Average Water
Pressure
Height of Drain Discharge Above Floor Upon Which Softener Sets
psi
4 in
1 ft
2 ft
3 ft
4 ft
5 ft
6 ft
7 ft
8 ft
9 ft
10 ft
kPa
0.1 m
0.3 m
0.6 m
0.9 m
1.2 m
1.5 m
1.8 m
2.1 m
2.4 m
2.7 m
3.1 m
30
56
50
40
30
20
10
210
17.1
15.3
12.2
9.2
6.1
3.1
50
112
106
96
86
76
66
56
46
36
26
16
350
34.2
32.3
29.3
26.2
23.2
20.1
17.1
14.0
11.0
7.9
4.9
70
143
137
127
117
107
97
87
77
67
57
47
480
43.6
41.8
38.7
35.7
32.6
29.6
26.5
23.5
20.4
17.4
14.3
90
153
147
137
127
117
107
97
87
77
67
57
620
46.7
44.8
41.8
38.7
35.7
32.6
29.6
26.5
23.5
20.4
17.4
120
159
153
143
133
123
113
103
93
83
73
63
830
48.5
46.7
43.6
40.6
37.5
34.5
31.4
38.4
25.3
22.3
19.2
12-INCH MODELS
Average Water
Pressure
Height of Drain Discharge Above Floor Upon Which Softener Sets
psi
4 in
1 ft
2 ft
3 ft
4 ft
5 ft
6 ft
7 ft
8 ft
9 ft
10 ft
kPa
0.1 m
0.3 m
0.6 m
0.9 m
1.2 m
1.5 m
1.8 m
2.1 m
2.4 m
2.7 m
3.1 m
30
44
38
28
18
210
13.4
11.6
8.5
5.5
50
103
97
87
77
67
57
47
37
27
17
7
350
31.4
29.6
26.5
23.5
20.4
17.4
14.3
11.3
8.2
5.2
2.1
70
129
123
113
103
93
83
73
63
53
43
33
480
39.3
37.5
34.5
31.4
28.4
25.3
22.3
19.2
16.2
13.1
10.1
90
145
139
129
119
109
99
89
79
69
59
49
620
44.2
42.4
39.3
36.3
33.2
30.2
27.1
24.1
21.0
18.0
14.9
120
153
147
137
127
117
107
97
87
77
67
57
830
46.7
44.8
41.8
38.7
35.7
32.6
29.6
26.5
23.5
20.4
17.4
INSTALLATION 11
Settings
The mircoprocessor can be set in three distinct operation modes. Aqua-Sensor Sensing Device, Soft-Minder
meter, or Timeclock. As shipped from the factory, the control is set for 9" Timeclock operation. A set of dip
switches, located on the back of the control, may have to be changed for proper operation of the unit. Refer to
Figure 12 and Table 3 for the proper setting of these dip switches.
AQUA-SENSOR  OPERATION
The Aqua-Sensor Sensing Device utilizes a pair of cells to sense the passage of hardness through the water
softener. It can automatically adjust for water with variable hardness levels. As a result, it is the most efficient
means of operating a water softener. When hardness is sensed, the unit signals for a regeneration. The
"REGEN" enunciator will light at this point. The unit will perform a standard regeneration cycle at the preset
time, unless the number 6 dip switch is turned on. When the number 6 dip switch is in the 'ON' position, a
regeneration will begin immediately.
The Aqua-Sensor models contain a feature which can automatically detect when the brine solution has been
rinsed through the Cullex media. This feature will advance the control to the next position when it senses that
the brine has been rinsed out prior to the time set in the Brine/Rinse option.
Since the Aqua-Sensor device automatically senses hardness in the water, the programming is limited to the
Time-of-Day, Time-of-Regeneration, Salt Dosage, Backwash Time and Brine/Rinse settings. The numeric
enunciator will only light for those programming options (numbers 1-6, 9, and 10). Refer to the programming
section for further information on programming the microprocessor.
SOFT-MINDER  OPERATION
The Soft-Minder meter utilizes a turbine impeller to accurately monitor the customers water usage. After a
predetermined amount of water has passed through the system, the microprocessor will signal a regeneration.
The "REGEN" enunciator will light at this point. The unit will perform a standard regeneration cycle at the
preset time, unless the number 6 dip switch is turned on. When the number 6 dip switch is in the 'ON' position, a
regeneration will begin immediately.
The microprocessor automatically calculates the gallons of water which can be treated based on the salt dosage,
the water hardness, and the tank size. Refer to Tables 4B and 5B for capacity and reserve values that the
microprocessor will use based on its settings. The GALLONS TO SIGNAL setting can be manually set to
directly override the microprocessor calculations. This setting can be modified when positioned at numeric
enunciator 8. The gallon value may need to be raised or lowered to meet the needs of your specific application.
The control must be cycled through a complete regeneration before the gallon override setting is stored by the
microprocessor.
NOTICE: Changing the capacity will affect the reserve capacity. An INCREASE in the gallons capacity will
DECREASE the reserve capacity. A DECREASE in the gallons capacity will INCREASE the reserve capacity.
Refer to Tables 4B and 5B to determine the units total capacity based on salt dosage and the hardness level.
The programming of the Soft-Minder provides several settable variables, the Time-of-Day, Time-of-Regeneration, Salt Dosage, Backwash Time, Brine/Rinse Time, Hardness, and Gallons to Signal. The numeric enunciator
will light for programming sequences 1-10. Refer to the programming section for further information on
programming the microprocessor.
12 CULLIGAN® MARK 100 WATER SOFTENER
TIME CLOCK OPERATION
When the mircoprocessor is set-up as a time clock unit, the Culligan Mark 100 control will regenerate at fixed intervals
which are determined by the water hardness, the salt dosage, and the household's water usage. To calculate the regeneration
interval, locate the total gallon capacity in Table 4B or 5B based on the salt dosage and the water hardness. Divide the units
total capacity by the anticipated daily gallon usage for the household. This value is the regeneration interval, always round
this value up to the nearest whole number. This regeneration interval can be set anywhere from 1 to 42 days.
The progamming for the time clock models is limited to Time-of-Day, Time-of-Regeneration, Salt dosage, Backwash Time,
Brine/Rinse Time, and the Regeneration Interval. The numeric enunciator will only light for those programming options
(numbers 1-6, and 8-10). Refer to the programming section for further information on programming the microprocessor.
CAPACITY AND SALT SETTINGS
The microprocessor calculates the total gallon capacity based on the salt
dosage, water hardness and tank size. Table 2 will help in anticipating
the total gallons of usage based on the total number of people in the
household.
For future reference, record the salt dosage, hardness level, and regeneration interval (time clock models only) below:
•
Salt Dosage
•
Hardness Level
•
Regeneration Interval (Days)
TIME CLOCK MODELS ONLY
TABLE 2 - DAILY WATER USAGE
Persons in
Household
2
3
4
5
6
7
8
9
10
Gallons
per Day
150
225
300
375
450
525
600
675
750
BRINE VALVE "A" DIMENSION
The Culligan unit contains a brine float which can serve as a backup refill
shutoff in the event of a failure, such as a power outage when in the refill
position. The float level should be set based on the salt dosage setting. Refer
to Figure 11.
•
•
•
"A"
Lift the brine valve from the brine chamber.
Find the correct “A” dimension from Tables 4 & 5.
Set the distance from the top of the filter screen to the base of the float
accordingly. The slight difference in height when the float is pulled up or
down is negligible.
FIGURE 11
SETTINGS 13
DIP SWITCH SETTING S
The microprocessor has several dip switches that can be switched for various additional functions. Listed are the
functions for the dip switches used on the Mark 100 control.
Dip Switch
Function
4
9"-12" Tank Settings
6
Delay vs. Immediate Regeneration
7
English vs. Metric Settings
8
12 or 24 Hour Clock
10
Time Clock Backup
Default (OFF) P o s i t i o n
9" Tank
Delayed Regeneration
English Settings
12 Hour Clock
No Forced Regeneration
Refer to Figure 12 for setting the dipswitches. As shipped from the factory all dip switches are in the off
position.
NOTICE: The end of a ball point pen works well to flip the dip switches as little force is required to flip the
switches. DO NOT use a pencil as the graphite may damage the dip switch.
FIGURE 12
TABLE 3 - DIP SWITCH SETTING
CONTROL TYPE
DIP SWITCHES
SH S
LI G
G IN
EN TT
SE
C
RI GS
ET IN
M TT
SE
9"
12"
9"
12"
1
2
3
4
5
6
7
8
9
10
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
14 CULLIGAN® MARK 100 WATER SOFTENER
Programming
Make sure the inlet water supply is turned off, then supply power to the timer. The display will power up flashing
"12:00 PM". After 1 minute the motor will energize and cycle the control, without stopping, to the home
position. This is required to ensure that the control is in the home position.
FIGURE 13 - Circuit Board Display
The timer uses four buttons:
1.
2.
3.
4.
STATUS:
UP ARROW:
DOWN ARROW:
REGEN.:
Advance timer through display options.
Increase the setting.
Decrease the setting.
Initiate a manual regeneration.
SETTING THE MICROPROCESSOR
The microprocessor senses when it is installed as a Soft-Minder or Aqua-Sensor® control. Adding or removing
any connection to the board while power is on, or flipping any of the dip switches will automatically reset the
microprocessor to the factory settings.
1.
2.
3.
4.
With a flashing or blank display,
pressing the status button twice will
move to the Time-of-Day adjustment.
Adjust the time by using the up and
down arrows. A number “1” will appear
at the bottom of the display while in this
mode.
Press status again, this displays the
Time-of-Regeneration for delayed
units, adjust using the up and down
arrows. A number “2” will appear at the
bottom of the display while in this
mode.
Press status again, the number “3” will
appear at the bottom of the display.
This setting is not used, and any
changes made will not affect the
operation of the microprocessor.
Pressing status again will show the Salt
Dosage. This can be adjusted with the
up and down arrows, the range is 3-15
lbs. for the 9” controls and 5-24 lbs. on
12” controls. A number “4” will appear
at the bottom of the display while in this
mode.
Press
▲ to increase or
▼ to decrease
Press
▲ to increase or
▼ to decrease
Press
▲ to increase or
▼ to decrease
Press
▲ to increase or
▼ to decrease
PROGRAMMING 15
5.
6.
7.
8.
Press status again, this displays the Backwash Time
in minutes. The setting can be adjusted between 5 and
40 minutes by using the up and down arrows. A
number “5” will appear at the bottom of the display
while in this mode.
Press
▲ to increase or
▼ to decrease
Press status again to display the Brine/Rinse Time in
minutes. The settings can be adjusted using the up
and down arrows (37-85 min for 9”, 35-89 min for
12”). A number “6” will appear at the bottom of the
display while in this mode.
Press
▲ to increase or
▼ to decrease
Press status again to display the Hardness Level in
grains per gallon. The setting can be adjusted from 299 gpg by using the up and down arrows. This
screen will not appear when the Aqua-Sensor® probe
is attached. A number “7” will appear at the bottom
of the display while in this mode.
Press status again, for time clock models the display
will show the Regeneration Interval. The setting
can be adjusted using the up and down arrows.
Controls with a Soft-Minder® meter will display the
Gallons to Signal (multiply the displayed value by
10). A number “8” will appear at the bottom of the
display while in this mode.
8A. Display menu '8A' will light when dip switch #10 is in
the ON position. This is the Time Clock Backup
feature. The control will force a regeneration, within
a range of 1-42 days, when in Aqua-Sensor® or SoftMinder® meter mode.
9.
Pressing status again will display the Lock/Unlock
feature. A “U” in the display signifies an unlocked
microprocessor, while a “L” will lock the settings
except for the time of day. To toggle between the two
settings press both arrow keys simultaneously. A
number “9” will appear at the bottom of the display
while in this mode.
10. Pressing status again brings up the ability to Enable/
Disable the screen blanking. To have the display
constantly lit, press the up arrow, a “d” for disable
will appear in the display. Pressing the up arrow
again displays an “E”, signifying that display blanking is enabled. A number “10” will appear at the
bottom of the display while in this mode.
Press
Press
Press
▲ to increase or
▼ to decrease
▲ to increase or
▼ to decrease
▲ to increase or
▼ to decrease
Press
▲ simultaneously
▼
Press
▲ to change
NOTICE: Programming changes are not locked into the microprocessor memory until the control completes a
regeneration cycle. To initiate a manual regeneration, press the REGEN. button twice, the "REGEN" enunciator will flash on the display. Refer to the Manual Cycling section on how to step through the regeneration
stages.
16 CULLIGAN® MARK 100 WATER SOFTENER
TABLE 4A - CAPACITY, 9” AQUA-SENSOR® SENSING DEVICE (GALLONS)
“A” DIMENSION
SALT
DOSAGE
8
12
HARDNESS
160 LB
250 LB
375 LB
INCH(CM) INCH(CM) INCH(CM)
1-5
6-10
11-15
16-20 21-25 26-30 31-35 36-40 41-45 46-50 51-55 56-60 61-65 66-70 71-75
14-3/4
(37.5)
9-1/4
(23.5)
7-1/2
(19.1)
TOTAL CAPACITY
CAPACITY TO SIGNAL
4,900
3,537
2,450
1,949
1,633
1,179
1,225
1,004
980
707
817
590
700
505
613
442
544
393
490
354
445
322
21-3/4
15-3/4
11-3/8
(26.9)
2,710
1,828
1,807
1,219
1,355
914
1,084
(40.0)
TOTAL CAPACITY
CAPACITY TO SIGNAL
5,420
(55.2)
903
609
774
522
678
457
602
406
542
366
493
332
3,656
731
452
305
417
281
387
261
301
244
TABLE 4B - CAPACITY, 9” SOFT-MINDER® METER (GALLONS)
“A” DIMENSION
SALT
DOSAGE
4
8
12
HARDNESS
160 LB
250 LB
375 LB
INCH(CM) INCH(CM) INCH(CM)
PROGRAMMING 17
1-5
6-10
11-15
7-3/4
(19.7)
4-5/8
(11.7)
3-1/4
(8.9)
TOTAL CAPACITY
CAPACITY TO SIGNAL
3,220
2,596
1,610
1,298
1,073
805
644
849
637
495
537
412
14-3/4
(37.5)
9-1/4
(23.5)
7-1/2
(19.1)
TOTAL CAPACITY
CAPACITY TO SIGNAL
4,900
3,314
2,450
1,657
1,633
1,225
980
817
700
613
544
1,084
813
631
526
442
387
333
21-3/4
(55.2)
15-3/4
(40.0)
11-3/8
(26.9)
TOTAL CAPACITY
CAPACITY TO SIGNAL
5,420
3,656
2,710
1,828
1,807
1,355
1,084
903
774
678
602
1,195
896
696
580
987
426
367
16-20 21-25 26-30 31-35 36-40 41-45 46-50 51-55 56-60 61-65 66-70 71-75
490
300
445
267
542
331
493
294
452
270
417
246
387
229
361
209
18 CULLIGAN® MARK 100 WATER SOFTENER
TABLE 5A - CAPACITY, 12” TIME CLOCK AND AQUA-SENSOR® SENSING DEVICE (GALLONS)
“A” DIMENSION
SALT
DOSAGE
HARDNESS
160 LB
250 LB
375 LB
INCH(CM) INCH(CM) INCH(CM)
1-5
6-10
11-15
16-20 21-25 26-30 31-35 36-40 41-45 46-50 51-60 61-70 71-80 81-90 91-99
12
21-3/4
(56.2)
15-3/4
(40.0)
11-3/8
(28.9)
TOTAL CAPACITY
CAPACITY TO SIGNAL
6,740
4,542
3,370
2,271
2,247
1,514
1,685
1,136
1,348
908
1,123
757
963
649
843
568
749
505
674
454
562
379
18
N/A
24-1/2
(62.2)
17-1/4
(43.8)
TOTAL CAPACITY
CAPACITY TO SIGNAL
7,660
5,200
3,830
2,600
2,553
1,733
1,915
1,300
1,532
1,040
1,277
867
1,094
743
958
650
851
578
766
520
638
433
547
371
479
325
426
289
383
260
TABLE 5B - CAPACITY, 12” SOFT-MINDER® METER (GALLONS)
“A” DIMENSION
SALT
DOSAGE
6
12
18
HARDNESS
160 LB
250 LB
375 LB
INCH(CM) INCH(CM) INCH(CM)
1-5
6-10
11-15
16-20 21-25 26-30 31-35 36-40 41-45 46-50 51-60 61-70 71-80 81-90 91-99
14-3/4
(37.5)
7-3/8
(18.7)
5-1/2
(14.0)
TOTAL CAPACITY
CAPACITY TO SIGNAL
4,520
3,495
2,260
1,748
1,507
1,143
1,130
904
753
646
565
857
666
555
466
408
21-3/4
(56.2)
15-3/4
(40.0)
11-3/8
(28.9)
TOTAL CAPACITY
CAPACITY TO SIGNAL
6,740
4,832
3,370
2,416
2,247
1,580
1,685
1,348
1,123
963
843
1,185
920
767
644
564
N/A
24-1/2
(62.2)
17-1/4
(43.8)
TOTAL CAPACITY
CAPACITY TO SIGNAL
7,660
5,346
3,830
2,673
2,553
1,748
1,915
1,532
1,277
1,094
958
1,311
1,018
849
713
624
749
486
674
437
562
357
851
537
766
484
638
395
547
335
479
286
426
246
383
219
Manual Cycling
The Culligan® microprocessor can be indexed through the various regeneration stages. For all steps, the cycle
numbers do not appear, or change, until the motor stops.
1.
Press the status button to move past steps 1-10
until the display is blank. Push the up arrow.
The number “11” icon will light up. An "H" will
appear in the display. The control is in the
HOME position. Pressing the regen button once
will light the 'REGEN' icon.
2.
Press the regen button one more time. The
'REGEN' icon will blink, and the motor will
advance the control. A '1' will appear. The unit
is now in the BACKWASH position. The
numbers to the right indicate the time remaining
for the cycle.
Press the up arrow. A '2' will appear in the
display, along with the cycle time remaining.
The control is in the BRINE DRAW/SLOW
RINSE cycle.
3.
4.
Press the up arrow. A '3' will appear in the
display, along with the cycle time remaining.
The control is now in the FAST RINSE/BRINE
REFILL cycle.
5.
Press the up arrow. An 'H' will appear in the
display. The unit is in the HOME position. The
'REGEN' enunciator is no longer blinking.
6.
Press the status key. Time-of-Day appears in the
display.
MANUAL CYCLING 19
Service Check
The service check mode allows one to view the instantaneous flow rate, the days since the last regeneration,
the total number of regenerations, the regenerations in the past fourteen days, and the gallons remaining.
To enter the service check mode, follow these steps:
1.
Press the status key to move past steps 1-10 until
the display is blank.
2.
Push the down arrow. The number '12' will
appear only when the Soft-Minder® meter is
connected. The display reads the gallons per
minute flow rate. This screen will update with
the current meter reading every 6 seconds.
3.
Press the down arrow. The number '13' and an
"A" will light at the bottom of the display. The
display will indicate the number of regenerations
that have occurred in the last 14 days.
4.
Press the down arrow. The number '13' and a 'B'
will light at the bottom of the display. The
display will indicate the total number of regenerations this control has cycled through.
5.
Press the down arrow. The number '14' will light
at the bottom of the display. The number in the
display indicates the number of days since last
regeneration.
6.
Press the down arrow. The number '15' will be
displayed if the flow meter or Aqua-Sensor® is
connected. For the controls with the SoftMinder® meter, the display indicates the gallons
remaining before the unit signals for regeneration
(multiply the displayed number by 10). For
Aqua-Sensor® controls, the number indicates the
total minutes of the last brine rinse cycle.
NOTICE: Pushing the up arrow at any of these displays will immediately bring you to the control position
display, the number '11' will light at the bottom of the display.
20 CULLIGAN® MARK 100 WATER SOFTENER
Operation
DISPLAY
There are two display modes on the Culligan® microprocessor. As shipped from the factory, the display of the
board is initially set to turn off if there has been no keyboard activity after a 1 minute period. Touching any key
will relight the display. The display can be set so that it will always display the time. For information on
changing the display lighting option, refer to the programming section.
REGENERATION
There are several conditions that will cause the control to trip a regeneration. The 'REGEN' enunciator will light
when the control has signaled for a regeneration. The 'REGEN' enunciator will flash while the control is in
regeneration. The following are conditions that will call for regeneration:
1.
2.
3.
4.
5.
6.
7.
When the Aqua-Sensor® probe senses the hardness in the Cullex® media.
When the Soft-Minder® meter has recorded the passage of a predetermined number of gallons.
When the time clock has counted past the set number of days.
At the preset time, when the number of days without a regeneration is equal to the days set in menu #8A.
At the preset time, when the 'REGEN.’ button is depressed once. 'REGEN.' will light.
Immediately, when the ‘REGEN.” button is depressed twice. 'REGEN.' will light and blink.
Immediately, if power to the unit has been off for more than 3 hours.
If dip switch 6 is in the ON position, the unit will begin a regeneration immediately for instances 1 and 2. With
dip swith 6 in the OFF position, the regeneration will not begin until the preset regeneration time.
START-UP
NOTICE: A sanitizing agent is added to the softener at the factory. Flush the tank to drain with a minimum of
40 gallons of water, or initiate a full regeneration cycle, prior to putting the unit into service.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Close the main water supply valve.
Set the Cul-Flo-Valv® to the bypass position.
Ensure that all faucets at the installation site are closed.
Direct the drain line discharge into a bucket where flow can be observed.
Plug the transformer into a 120 Volt, 60 Hz, single-phase receptacle.
Wait 1 minute for the control to energize the motor and home itself.
Set the timer to the correct time of day.
Open the main supply valve.
Initiate an immediate regeneration to move the control into the backwash position.
Refer to the section on manual cycling for information on cycling the control through its positions.
When in the backwash position, slowly shift the bypass to the soft water position until water flows.
Allow the tank to fill slowly until water flows from the drain line.
When flow to drain is established, open the bypass fully. Watch the drain line discharge for signs of resin.
If signs of resin particles appear, reduce the flow. Increase the flow again when resin no longer appears in
the discharge.
When the unit is filled with water, return the timer to the service position and proceed with setting the
microprocessor. Refer to the programming section.
NOTICE: Unplugging the Culligan® Mark 100 water softener will not affect any of the timer settings. Once
programmed in, the settings will be stored indefinitely. In the event of a power failure the time-of-day setting
will be stored for 1-2 days. If longer time storage is necessary, a battery backup is available. Refer to the
Service Manual for additional information.
OPERATION 21
BEFORE LEAVING THE INSTALLATION SITE
Flush the sanitizing solution from the unit by running it to drain for a minimum of 40 gallons, or initiate a full
recharge cycle (by pushing the 'REGEN.' button twice).
Ensure that the brine tank has water to the level of the float. Add water to the tank with a hose or put the unit
into a full recharge so that the brine refill cycle will fill the tank with the proper amount of water.
The water heater will hold hard water for several days. Advise the customer that the existing water volume
in the tank will need to be used before the hot water is soft. If soft hot water is required immediately, refer to the
water heater owner's manual for the proper method of draining the water heater.
Explain the operation of the softener to the customer. Make sure the customer knows that there will be new
sounds associated with the recharging of the unit. Advise the customer to periodically check and replenish the
salt supply.
Check the approiate softener model box on page 2 of the Owner's Guide. Fill in the hardness and number of
people, and then sign and date the corresponding performance data sheet. Leave the Owner's Guide with the
customer.
Clean up the unit and installation site, removing any soldering, or pipe threading, residues from the equipment
and surrounding area with a damp towel.
22
CULLIGAN® MARK 100 WATER SOFTENER
Sanitizing Instructions
A water softener in daily use on a potable water supply generally requires no special attention other than keeping
the salt tank filled. Occasionally, however, a unit may require sanitation under one of the following conditions:
•
•
The unit has stood idle for a week or more (the premises vacant or the residents on vacation).
On private supplies, the appearance of off-tastes and odors, particularly a musty or "rotten egg" odor .
For occasional occurrences, the softener can be sanitized with household bleach as follows.
NOTICE: If the water supply contains iron, regenerate the softener before sanitizing to remove accumulated iron
from the Cullex® resin.
WARNING: HAZARD FROM TOXIC FUMES! CHLORINE BLEACH AND
COMMON IRON CONTROL CHEMICALS MAY GENERATE TOXIC FUMES
WHEN MIXED.
•
IF THE UNIT USES CULLIGAN® SOFNER-GARD™ CHEMICAL OR OTHER COMPOUNDS
CONTAINING SODIUM HYDROSULFITE OR SODIUM BISULFITE, OR ANY OTHER
REDUCING AGENT, DISCONNECT THE DEVICE AND MANUALLY REGENERATE THE UNIT
BEFORE SANITIZING.
•
DO NOT USE THIS PROCEDURE IF THE SOFTENER SALT CONTAINS IRON CONTROL
ADDITIVES.
1.
Remove the brine tank cover and the small cover on the brine valve chamber.
2.
Pour directly into the brine chamber 1 cup (9-inch units) or 2 cups (12-inch units) of common household
bleach (5-1/4% sodium hypochlorite).
NOTICE: Do not use lemon scented bleaches, or similar bleaches that contain perfumes.
3.
Manually start a recharge cycle. Allow the unit to complete the recharge cycle automatically.
If tastes and odors return frequently, even after sanitization, additional equipment my be required. Have a laboratory analysis performed to determine the possible cause of the odor. Contact Household Application Engineering
for assistance. Also, have the consumer send a sample to a qualified laboratory for bacterial analysis.
SANITIZING INSTRUCTIONS 23
Parts List - Control
24
CULLIGAN® MARK 100 WATER SOFTENER
Item
Part No.
—
1
2
3
*
*
*
*
4
5
6
7
8
01-0112-89
00-4498-65
01-0130-83
01-0136-06
P0-4479-86
P0-3084-07
P0-4487-50
00-4479-87
00-4432-91
P0-3031-92
P0-3031-93
00-4468-35
P0-3316-35
P0-3316-36
00-4473-87
P0-3084-38
00-3084-37
00-4012-48
00-4460-38
00-4460-39
P0-4452-69
00-4457-97
00-4010-22
00-4486-87
01-0051-30
00-4481-28
P0-4449-14
00-4481-26
01-0046-89
P0-3183-83
01-0128-12
01-0128-68
00-4486-86
00-2183-43
00-4452-72
01-0032-44
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
9
10
11
12
13
CONTROL VALVE PARTS LIST
14
‡ 15
16
17
18
19
‡ 20
21
22
23
24
25
26
27
28
‡ 29
Description
Control Valve Assembly - Mark 100
Control Valve
Seal Pack Assembly
Eductor Sleeve and Eductor Piston Assembly
O-Ring, Eductor Sleeve, Small O-Ring (25/Kit)
O-Ring, Eductor Sleeve, Large O-Ring (25/Kit)
Screen, Eductor Sleeve (10/Kit)
O-Ring, Eductor Piston (10/Kit)
Connector Brine Line
Insert, PP, 0.312" (25/Kit)
Nut, PP, 0.312" (25/Kit)
Drain Elbow Assembly w/O-Ring
Backwash Restrictor, #2, 9" Tanks (10/Kit)
Backwash Restrictor, #3, 12" Tanks (10/Kit)
Retainer, Drain Elbow
O-Ring, Eductor Nozzle and Throat (10/Kit)
O-Ring, Eductor Throat
Eductor Throat w/O-Rings
Eductor Nozzle - Blue, 9" Tanks
Eductor Nozzle - Beige, 12" Tanks
Eductor Screen (10/Kit)
Gasket
Eductor Port Cover
Screw
Bracket
Retainer, Rear Body Plug
O-Ring, Rear Seal (10/Kit)
Rear Body Plug
Cul-Flo Bracket
Screw (10/Kit)
Control Back Plate
Timer Label
Screw
Washer
Barrier
Switch
‡ Recommended Spare Parts
* Not Illustrated
Item
Part No.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
*
*
*
*
*
00-4010-40
00-3184-55
P1-0130-43
01-0130-31
01-0017-84
00-4435-59
00-3184-52
01-0136-04
00-3183-54
00-4452-21
00-4452-46
01-0126-49
01-0126-48
01-0126-47
01-0128-09
01-0128-67
00-4022-01
01-0128-08
01-0128-10
01-0065-05
01-0127-76
A0-4880-16
01-0064-98
01-0003-72
00-4015-67
01-0128-45
00-3184-55
01-0111-96
00-3318-48
01-0128-05
00-4414-10
01-0128-34
01-0127-76
01-0129-56
01-0129-05
01-0129-58
00-4517-01
01-0138-39
Description
Switch Bracket
Screw
Retaining E-Ring (10/Kit)
Cam
Screw
Roll Pin
Screw
Drive Motor & Bracket Assembly 24V/60Hz
Nut
Bellcrank
Roll Pin
Follower
Yoke
Bracket
Cover
Setting Label
Screw
Door
Door Retaining Clip
Circuit Board Mounting Plate
Standoff
Power Cord
Plug, Snap-In
Strain Relief
Wire Clip
Transformer
Screw
Screw
Terminal Strip
Hinge, Circuit Board Plate
Screw
Circuit Board
Standoff Hinge
Wall Mount Transformer
Flow Meter Assembly
Wire Harness, Cam
Hose Clamp, Drain
Back-up Battery
25
Parts List - Tank Assembly
Item Part Number
*
01-0064-63
*
01-0101-35
*
01-0037-57
*
01-0037-58
*
01-0042-97
*
01-0043-00
*
01-0042-98
*
01-0042-99
1
2
01-0072-81
01-0103-28
01-0103-29
P0-2320-07
P0-3339-57
4
5
Description
Tank Assembly, 9"
Aqua-Sensor®, Complete
Tank Assembly, 12"
Aqua-Sensor, Complete
Tank Assembly, 9"
Soft-Minder®, Complete
Tank Assembly, 12"
Soft-Minder, Complete
Tank Replacement, 9"
Aqua-Sensor, Empty
Tank Replacement, 12"
Aqua-Sensor, Empty
Tank Replacement, 9"
Soft-Minder, Empty
Tank Replacement, 12"
Soft-Minder, Empty
Outlet Manifold
Aqua-Sensor Probe, 9"
Aqua-Sensor Probe, 12"
Inlet Manifold (25/Kit)
O-Ring (25/Kit)
26 CULLIGAN® MARK 100 WATER SOFTENER
Qty.
Item Part Number Description
6
7
8
9
10
11
12
13
14
15
16
17
1
1
1
1
18
P0-3044-11
01-0072-82
01-0072-83
01-0072-88
01-0072-87
01-0021-19
01-0054-50
00-3232-05
01-0072-84
01-0072-85
01-0019-46
01-0019-47
00-4445-85
00-4445-46
00-4419-97
00-4446-45
00-4445-83
00-4446-44
00-2202-36
00-2202-22
O-Ring (25/Kit)
Inlet Adaptor
Nut, Plastic
Cover Plate, Sensor
Cover Plate, Meter
Plate
Gasket
Barrier
Yoke, Sensor
Yoke, Meter
Cover, 9"
Cover, 12"
Crush Pad, 9"
Crush Pad, 12"
Gasket, Ring, 9"
Gasket, Ring, 12"
Well, 9"
Well, 12"
Liner, 9"
Liner, 12"
Qty.
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Parts List - Salt Storage Tank
Item Part Number
—
—
—
† 1
2
3
*
*
00-4413-90
00-4418-86
00-4418-87
01-0048-70
00-3039-93
00-4010-42
00-3039-80
00-3040-10
00-4413-91
00-3039-75
00-3044-30
00-3044-39
Description
Brine System, 160 lb. Replacement
Brine System, 250 lb. Replacement
Brine System, 375 lb. Replacement
Gold Band
Cover with Band, 250 lb. (114 kg)
Cover with Band, 160 lb. (73 kg)
Cover with Band, 375 lb. (170 kg)
Tank Only, 250 lb. (114 kg)
Tank Only, 160 lb. (73 kg)
Tank Only, 375 lb. (170 kg)
Salt Plate, Plastic, 250 lb. (114 kg)
Salt Plate, Plastic, 375 lb. (170 kg)
* Not Illustrated
† Order by footage required
CONTROL VALVE PARTS LIST
27
Parts List - Brine Well & Float
Item Part Number
—
—
1
2
3
‡4
‡5
6
00-4418-88
00-4011-41
00-3031-93
00-3031-92
00-4407-96
00-3084-07
00-4016-22
00-3400-14
7
‡8
9
00-4407-95
00-3325-28
00-2234-35
10
11
12
13
14
‡15
16
17
‡18
19
00-3047-03
00-3047-18
00-4448-73
00-3320-72
00-4446-64
00-4444-96
00-4473-92
00-4477-81
00-3048-04
00-5418-21
00-5418-34
20
00-3045-37
21
*
*
00-4413-92
00-3046-06
00-4463-88
00-4463-89
Description
Brine Valve Assembly
Brine Valve Assy., Brine Tank, 160 lb.
Plastic Nut, 5/16-inch
Plastic Insert
Refill Cap
O-ring
Flow Restrictor, No. 5, 0.45 gpm (170 lpm)
Stem Seat Assy., 250 lb. (114 kg) & 375 lb.
(170 kg)
Refill Body
Hat Screen
Plastic Pipe, 1/4-inch NPT x 35 inches long,
250 lb. (114 kg) & 375 lb. (170 kg)
Float Retainer (2 required)
Float Weight, Stainless Steel (2)
Float
Screen Top Seal
Filter Screen Cap
Stem Seat
Insert
Air Eliminator Ball
Ball Seat
Float Valve Body with Ball Seat
Float Valve Body with Ball Seat, 150 lb.
Brine Tank
Brine Valve Chamber, 250 lb. (114 kg) &
375 lb. (170 kg) Salt Storage Tank
Brine Valve Chamber, 160 lb. (Shown)
Cap, Brine Valve Chamber
Screw, St. Steel, Brine Valve Chamber
Nut, St. Steel, Brine Valve Chamber
* Not Illustrated
‡ Recommended Spare Parts
CULLIGAN INTERNATIONAL COMPANY
One Culligan Parkway, Northbrook, IL 60062-6209
28 CULLIGAN® MARK 100 WATER SOFTENER