Allied Telesis AT-MC15 Installation guide

AT-MC13
AT-MC14
AT-MC15
AT-MC16
Ethernet Media Converters
Installation Guide
PN 613-10724-00 Rev C
Copyright  2001 Allied Telesyn International Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086 USA
All rights reserved. No part of this publication may be reproduced without prior written
permission fro Allied Telesyn International Corp.
e
Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.
Allied Telesyn International Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allied
Telesyn International Corp. be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits, arising out
of or related to this manual or the information contained herein, even if Allied Telesyn
International Corp. International Corp. has been advised of, known, or should have
known, the possibility of such damages.
Electrical Safety and Emission Compliance
Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International Corp.
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet Media Converters
Model Numbers:
AT-MC13, AT-MC14, AT-MC15, AT-MC16
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device must not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on. The user is encouraged to try to correct
the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer
or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
iii
Warning: In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate
measures.
RFI Emission
EN55022 Class B $ 1
Immunity
EN55024 $ 2
Warning (AT-MC13, AT-MC14, AT-MC16): This product requires shielded cables to
comply with emission and immunity standards. If it is used with unshielded
cables, the user may be required to take measures to correct the interference
problem at their own expense. $ 3
Electrical Safety
TUV-EN60950, UL1950, CSA 950 $ 4
Laser
EN60825 $ 5
Important: Appendix B contains translated safety statements for installing
this equipment. When you see the $, go to Appendix B for the translated
safety statement in your language.
Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die
Installation dieses Geräts. Wenn Sie $ sehen, schlagen Sie in Anhang B den
übersetzten Sicherheitshinweis in Ihrer Sprache nach.
Vigtigt: Tillæg B indeholder oversatte sikkerhedsadvarsler, der vedrører
installation af dette udstyr. Når De ser symbolet $, skal De slå op i tillæg B
og finde de oversatte sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix B bevat vertaalde veiligheidsopmerkingen voor het
installeren van deze apparatuur. Wanneer u de $ ziet, raadpleeg Appendix
B voor vertaalde veiligheidsinstructies in uw taal.
Important: L'annexe B contient les instructions de sécurité relatives à
l'installation de cet équipement. Lorsque vous voyez le symbole $, reportezvous à l'annexe B pour consulter la traduction de ces instructions dans votre
langue.
Tärkeää: Liite B sisältää tämän laitteen asentamiseen liittyvät käännetyt
turvaohjeet. Kun näet $-symbolin, katso käännettyä turvaohjetta liitteestä
B.
Importante: l’Appendice B contiene avvisi di sicurezza tradotti per
l’installazione di questa apparecchiatura. Il simbolo $, indica di consultare
l’Appendice B per l’avviso di sicurezza nella propria lingua.
Viktig: Tillegg B inneholder oversatt sikkerhetsinformasjon for installering
av dette utstyret. Når du ser $, åpner du til Tillegg B for å finne den
oversatte sikkerhetsinformasjonen på ønsket språk.
Importante: O Anexo B contém advertências de segurança traduzidas para
instalar este equipamento. Quando vir o símbolo $, leia a advertência de
segurança traduzida no seu idioma no Anexo B.
Importante: El Apéndice B contiene mensajes de seguridad traducidos para
la instalación de este equipo. Cuando vea el símbolo $, vaya al Apéndice B
para ver el mensaje de seguridad traducido a su idioma.
Obs! Bilaga B innehåller översatta säkerhetsmeddelanden avseende
installationen av denna utrustning. När du ser $, skall du gå till Bilaga B
för att läsa det översatta säkerhetsmeddelandet på ditt språk.
iv
Table of Contents
Electrical Safety and Emission Compliance Statement . . . . . . . . . . . . iii
Welcome to Allied Telesyn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Where to Find Web-based Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Contacting Allied Telesyn Technical Support . . . . . . . . . . . . . . . . . . . . . . . . viii
Online Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Telephone and Fax Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Technical Support E-mail Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Returning Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
For Sales or Corporate Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Tell Us What You Think . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Chapter 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Status LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MDI/MDI-X Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fiber Link Test Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MissingLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminator Switch (AT-MC15 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External AC/DC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Standalone Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back-to-Back Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2
Installing the Media Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reviewing Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Media Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
15
16
17
v
Chapter 3
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix A
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Electrical Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Agency Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Appendix B
Translated Safety and Emission Information . . . . . . . . . . . . . . . . . . . . . 25
Appendix C
Technical Support Fax Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Incident Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
vi
Welcome to Allied Telesyn
This guide contains instructions on how to install the AT-MC1x Series
Ethernet Media Converters.
Where to Find Web-based Guides
The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation and technical information
for all of our products. For product guides, you can go directly to the following
web page: www.alliedtelesyn.com/support/prd_libs.htm.
Document Conventions
This guide uses several conventions that you should become familiar with first
before installing the product.
Note
A note provides additional information.
Caution
A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.
Warning
A warning indicates that performing or omitting a specific action may
result in bodily injury.
vii
Welcome to Allied Telesyn
Contacting Allied Telesyn Technical Support
You can contact Allied Teleysn technical support online or by telephone, fax, or
e-mail.
Online Support
You can request technical support online by filling out the Online Technical
Support Form at www.alliedtelesyn.com/support/supportf.asp or by
accessing the Technical Support Knowledge Base from Allied Telesyn’s North
American web site. You can use the Knowledge Base to submit questions to our
technical support staff and review answers to previously asked questions.
Telephone and Fax Support
For Technical Support via fax, please fill out the “Technical Support Fax
Order” on page 35 and send it to the appropriate location listed below.
Americas
United States, Canada, Mexico,
Central America, South America
Tel: 1 (800) 428-4835, option 4
Fax: 1 (425) 481-3790
Germany
Germany, Switzerland, Austria, Eastern
Europe
Tel: (+49) 30-435-900-126
Fax: (+49) 30-435-70-650
Asia
Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: (+65) 3815-612
Fax: (+65) 3833-830
Italy
Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: (+39) 02-41-30-41
Fax: (+39) 02-41-30-42-00
Australia
Tel: 1 (800) 000-880
Fax: (+61) 2-9438-4966
Japan
Tel: (+81) 3-3443-5640
Fax: (+81) 3-3443-2443
France
France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: (+33) 0-1-60-92-15-25
Fax: (+33) 0-1-69-28-37-49
United Kingdom
United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: (+0044) 1235-442500
Fax: (+44) 1-235-442680
viii
AT-MC1x Series Installation Guide
Technical Support E-mail Addresses
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
Europe
support_europe@alliedtelesyn.com
Returning Products
Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a RMA
number will be returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:
North America
Toll-free: 1-800-428-4835, option 4
Fax: 1-425-481-3790
Europe, Africa, and the Middle East
Tel: +44-1793-501401
Fax: +44-1793-431099
Latin America, the Caribbean, and
Virgin Islands
Tel: international code + 425-481-3852
Fax: international code + 425-481-3895
Puerto Rico
Tel: 1-800-424-5012, ext 3852 or
1-800-424-4284, ext 3852
Mexico
Toll-free: 800-424-5012, ext 3852
Fax: international code + 425-481-3895
Asia and Southeast Asia
Tel: +65-381-5612
Fax: +65-383-3830
Australia
Toll-free: 1-800-000-880
Fax: +61-2-9438-4966
New Zealand
Toll-free: 0800-45-5782
FTP Server
If you need management software for an Allied Telesyn managed device and
you know the file name of the software, you can download the software by
connecting directly to our FTP server at ftp.alliedtelesyn.com. At login,
enter ‘anonymous’ as the user name and your e-mail address for the password.
ix
Welcome to Allied Telesyn
For Sales or Corporate Information
You can contact Allied Telesyn for sales or corporate information at one of the
locations below:
Allied Teleyn International Corp.
19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn International Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94085
Tel: 1 (800) 424-4284 (US and Canada)
Fax: 1 (408) 736-0100
Tell Us What You Think
If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, please fill out the Send Us Feedback Form at
www.alliedtelesyn.com/contact/feedbackf.asp.
x
Chapter 1
Overview
The AT-MC1x Series Ethernet Media Converters includes the following
models:
q AT-MC13
q AT-MC15
q AT-MC14
q AT-MC16
These media converters are designed to extend the distance of your network by
interconnecting twisted pair cabling to single-mode or multimode fiber optic
cabling or thinnet cabling. The AT-MC1x Series Media Converters allow you to
interconnect LAN devices over large distances.
The AT-MC13, AT-MC14, and AT-MC16 media converters feature a 10Base-T
twisted pair port and a 10Base-F fiber optic port. The twisted pair port has an
RJ-45 connector and a maximum operating distance of 100 meters (328 feet).
The fiber optic port has an ST or SC connector and a maximum operating
distance of 2 kilometers (1.2 miles) to 100 kilometers (62 miles), depending on
the model. These media converters operate at 10 Mbps and feature half- and
full-duplex operation.
The AT-MC15 features a 10Base-T twisted pair port and a 10Base2 thinnet
port. The twisted pair port has an RJ-45 connector and a maximum operating
distance of 100 meters (328 feet). The thinnet port has a BNC-type connector
and a maximum operating distance of 185 meters (606 feet). The AT-MC15
operates at 10 Mbps and features half-duplex operation.
The AT-MC1x Series Media Converters can be used on a desktop or in an
AT-MCR12 chassis. These media converters are easy to install and do not
require software configuration or management.
1
Figure 1 illustrates an AT-MC1x Series Media Converter.
FIBER
LINK TEST
TX
RX
10Base-F
10Base-T
REC
PWR
REC
NML
LNK
MDI
LNK
MDI-X
MC13 ETHERNET MEDIA CONVERTER
Figure 1 AT-MC1x Series Media Converter (AT-MC13 model)
Table 1 lists the maximum operating distances for the AT-MC13, AT-MC14,
and the AT-MC16 media converters.
Table 1 Maximum Operating Distances
10Base-F
Model
10Base-T
Connector
Maximum Operating
Distance1
Connector
Maximum Operating
Distance
AT-MC13
ST
2 km (1.2 mi)
RJ-45
100 m (328 ft)
AT-MC14
SC
2 km (1.2 mi)
RJ-45
100 m (328 ft)
AT-MC16
ST
15 km (9.3 mi)
RJ-45
100 m (328 ft)
1. Maximum operating distance may be less depending on the duplex mode of the end stations and the type of fiber
optic cabling used with the port.
Table 2 lists the maximum operating distances for the AT-MC15 media
converter.
Table 2 Maximum Operating Distances
10Base2
Model
AT-MC15
2
10Base-T
Connector
Maximum Operating
Distance
Connector
Maximum Operating
Distance
BNC
185 m (606 ft)
RJ-45
100 m (328 ft)
AT-MC1x Series Installation Guide
Key Features
The media converters have the following key features:
q LEDs for unit and port status
q Full- or half-duplex mode operation (except AT-MC15)
q Half-duplex mode operation (AT-MC15 only)
q MissingLink notifies end-nodes of link failures (fiber models only)
q Link Test feature performs a link test on the media converter’s fiber
port
q MDI/MDI-X switch that eliminates the need for a crossover cable
q Internal termination on the BNC port (AT-MC15 only)
q External AC/DC power adapter
q Standard, compact size for desktop use or in an AT-MCR12 rackmount
chassis
Status LEDs
Table 3 lists the status LEDs for the AT-MC1x Series Media Converters.
Table 3 Status LEDs for the Media Converters
LED
Color
Description
PWR
Green
Power is applied to the media converter.
LNK
Green
A link has been established on the port.
REC
Green
Data is being received.
All Models
AT-MC13, AT-MC14 and AT-MC16 only
NML
Green
The MissingLink feature is enabled and the media converter is
functioning in normal operating mode.
OFF
The MissingLink feature is disabled and the media converter is
performing a link test.
3
Table 3 Status LEDs for the Media Converters (Continued)
LED
Color
Description
TX
Green
Data is being transmitted on the BNC port.
RX
Green
Data is being received on the BNC port.
ONLINE
Green
The BNC port is connected to an active 10Base2 segment.
COL
Green
The BNC port is sensing a collision signal.
AT-MC15 Only
MDI/MDI-X Switch
An RJ-45 port on a 10 Mbps Ethernet network device can have one of two
possible wiring configurations: MDI or MDI-X. The RJ-45 port on a PC, router
or bridge is typically wired as MDI, while the twisted pair port on a switch or
hub is usually MDI-X.
To connect two 10 Mbps network devices together that have dissimilar port
wiring configurations, such as MDI to MDI-X, you use a straight-through cable.
To connect two network devices that have an RJ-45 port with the same wiring
configuration, such as MDI to MDI, you use a crossover cable.
The RJ-45 port on the media converters feature an MDI/MDI-X button. You can
use this button to configure the twisted pair port on the media converter as
either MDI or MDI-X, thus eliminating the need for a crossover cable
regardless of the type of network device you are connecting to the unit.
Table 4 lists the pinouts of the RJ-45 ports for both MDI and MDI-X wiring
configurations.
Table 4 RJ-45 Pinout
MDI Pinout
MDI-X Pinout
Pin
Signal
Pin
Signal
1
TD +
1
RD+
2
TD-
2
RD-
3
RD+
3
TD+
6
RD-
6
TD-
4, 5, 7, 8
N/A
4, 5, 7, 8
N/A
4
AT-MC1x Series Installation Guide
Fiber Link Test Switch
The AT-MC13, AT-MC14, and AT-MC16 media converters feature a Fiber Link
Test switch. This switch sets the fiber port into an artificial link transmission
state for testing without the twisted pair port being connected. When the Fiber
Link Test switch is in the DOWN (default) position, the NML LED is green
indicating that the media converter is functioning normally. For a link test, set
the switch in the UP position. Be sure to set the switch back to the default
position after performing a link test. If the switch is left in the UP position, the
media converter will not function properly. Refer to Figure 2 for the location of
the Fiber Link Test switch.
FIBER
LINK TEST
TX
RX
10Base-F
10Base-T
REC
PWR
REC
NML
LNK
MDI
MDI-X
LNK
MC13 ETHERNET MEDIA CONVERTER
FIBER
LINK TEST
Figure 2 Fiber Link Test Switch
5
Auto-negotiation
Auto-negotiation determines the duplex mode of the ports. The duplex mode
refers to the manner in which an end-node sends and receives data on the
network. Depending on its capabilities, an end-node can operate in either halfor full-duplex mode. An end-node operating in half-duplex can either send or
receive data, but not both at the same time. However, an end-node operating
in full-duplex can send and receive data simultaneously. The best network
performance is achieved when an end-node can operate in full-duplex mode.
The AT-MC13, AT-MC14, and AT-MC16 media converters can operate in
either full- or half-duplex mode. However, it is important to note that the endnodes connected to these media converters must operate in the same duplex
mode to avoid a duplex mode mismatch which can result in poor network
performance.
Figure 1 shows an example of a duplex mode mismatch. A repeater (Unit 1),
capable of operating in half-duplex mode only, is connected to the 10Base-F
port on the media converter, while a switch (Unit 2), capable of either half- or
full-duplex mode, is connected to the 10Base-T port on the media converter.
Unit 1
Unit 2
FIBER
LINK TEST
TX
RX
10Base-F
10Base-T
REC
PWR
REC
NML
LNK
MDI
100Base-TX Repeater
MDI-X
LNK
Media Converter
100Base-TX Switch
Figure 1 Example of a Duplex Mode Mismatch
In attempting to auto-negotiate with Unit 1, the media converter will
determine that the repeater is capable of half-duplex only and will set the port
connected to the unit appropriately. In auto-negotiating with Unit 2, the
media converter will determine that the switch can manage full-duplex and
will set the port connected to the switch to full-duplex. The result is a duplex
mode mismatch, with one unit operating in half-duplex and the other unit
operating in full-duplex. You can resolve the duplex mode mismatch by
manually configuring Unit 2, if possible, so that the port connected to the
media converter is set to half-duplex.
6
AT-MC1x Series Installation Guide
MissingLink
The MissingLink feature enables the ports on the media converter to pass the
“Link” status of their connections to each other. When the media converter
detects a problem with one of the ports, such as the loss of connection to a endnode, the media converter shuts down the connection to the other port, thus
notifying the end-node that the connection has been lost.
For example, if the network twisted pair cable on an AT-MC14 were to fail, the
module would respond by dropping the link on the fiber optic port. In this way,
the AT-MC14 notifies the end-node connected to the fiber optic port that the
connection on the twisted pair port has been lost. If the failure had started with
the fiber optic cabling, the unit would drop the link to the twisted pair port.
The value to this type of network monitoring and fault notification is that some
hubs and switches can be configured to take a specific action in the event of the
loss of connection on a port. In some cases, the unit can be configured to seek a
redundant path to a disconnected end-node or send out a trap to a network
management station, alerting the network administrator of the problem.
Note
MissingLink is disabled when you perform a link test with the Fiber
Link Test switch. Consequently, to ensure that MissingLink is enabled
on the media converter, always set the Fiber Link Test switch to the
DOWN position during normal network operations.
7
Terminator Switch (AT-MC15 Only)
The Terminator switch on the AT-MC15 media converter offers 50 Ω
termination without the use of a T-connector and 50 Ω barrel terminator. Only
end-point nodes need 50 Ω termination. Internal nodes on a thinnet segment
should be connected to the cable through standard 10Base2 T-connectors. Refer
to Figure 3 for the location of the Terminator switch.
10Base2
TERMINATOR
O
F
F
10Base-T
RX
RX
PWR
ONLINE
O
N
LNK
COL
TX
MDI
MDI-X
TX
MC15 ETHERNET MEDIA CONVERTER
TERMINATOR
O
F
F
Figure 3 Terminator Switch
8
O
N
AT-MC1x Series Installation Guide
External AC/DC Power Adapter
An external AC/DC power adapter is included with the media converter for
desktop operation (see Figure 4). The power adapter supplies 12 V DC to the
media converter. Allied Telesyn supplies an approved safety compliant AC
power adapter for the 120 and 240 V AC versions with an unregulated output
of 12 V DC at 1 A. The power requirement for the AT-MC13, AT-MC14, and
AT-MC16 media converters is 12 V DC, 500 mA. The power requirement for the
AT-MC15 is 12 V DC, 300 mA
Note
The power adapter is not used if you install the media converter in an
AT-MCR12 chassis.
Figure 4 External AC/DC Power Adapter (North American Version)
9
Network Topologies
The AT-MC1x Series Media Converters can be used in two different topologies:
standalone and back-to-back. Both types of topologies are described below.
Standalone Topology
A standalone topology uses one media converter between the end-nodes. Figure
5 illustrates a standalone topology that uses an AT-MC13 media converter to
connect two switches.
10Base-F Fiber Optic Switch
2 km (1.2 mi)
AT-MC13
FIBER
LINK TEST
TX
RX
10Base-F
10Base-T
REC
PWR
REC
NML
LNK
MDI
MDI-X
LNK
MC13 ETHERNET MEDIA CONVERTER
100 m (328 ft)
Fiber Optic
10BASE-T / 100BASE-TX
FAST ETHERNET SWITCH
A
Twisted Pair
10BASE-T / 100BASE-TX
PORT ACTIVITY
1X
3X
5X
7X
9X
11X
13X
15X
17X
19X
21X
23X
2X
4X
6X
8X
10X
12X
14X
16X
18X
20X
22X
24X
100M LINK /
L /A
ACTIVITY
RS-232
TERMINAL PORT
10M LINK /
HALF DUP/
FULL DUP
D/C
STATUS
ACTIVITY
COL
1
3
5
7
9
11
13
15
17
19
21
23
2
4
6
8
10
12
14
16
18
20
22
24
FAULT
L /A
D/C
B
RPS
L /A
PWR
D/C
RESET
AT-8224XL Switch
Figure 5 Standalone Topology
10
AT-MC1x Series Installation Guide
Back-to-Back Topology
In some network configurations you may want to interconnect two media
converters in what is referred to as a back-to-back topology. In this topology,
the media converters not only extend the distance of your network but also
convert the fiber optic cable from twisted pair to fiber optic and back again.
Figure 6 illustrates two AT-8224XL switches at different campuses
interconnected by two AT-MC14 media converters. The 10Base-T ports on the
media converters are connected to one 10/100Base-TX port on each switch,
while the 10Base-F ports on the media converters are directly connected
together.
Campus 1: One AT-8224XL Switch
10BASE-T / 100BASE-TX
FAST ETHERNET SWITCH
A
10BASE-T / 100BASE-TX
PORT ACTIVITY
1X
3X
5X
7X
9X
11X
13X
15X
17X
19X
21X
23X
2X
4X
6X
8X
10X
12X
14X
16X
18X
20X
22X
24X
100M LINK /
L /A
ACTIVITY
RS-232
TERMINAL PORT
10M LINK /
STATUS
ACTIVITY
HALF DUP/
FULL DUP
D/C
COL
1
3
5
7
9
11
13
15
17
19
21
23
2
4
6
8
10
12
14
16
18
20
22
24
FAULT
L /A
D/C
B
RPS
L /A
PWR
D/C
RESET
100 m (328 ft)
AT-MC14
AT-MC14
FIBER
LINK TEST
TX
RX
10Base-F
10Base-T
REC
REC
LNK
MDI
MDI-X
FIBER
LINK TEST
TX
RX
10Base-T
10Base-F
PWR
REC
NML
LNK
LNK
MC14 ETHERNET MEDIA CONVERTER
REC
PWR
NML
MDI
LNK
MDI-X
MC14 ETHERNET MEDIA CONVERTER
2 km (1.2 mi)
100 m (328 ft)
Fiber Optic
10BASE-T / 100BASE-TX
FAST ETHERNET SWITCH
A
Twisted Pair
10BASE-T / 100BASE-TX
PORT ACTIVITY
1X
3X
5X
7X
9X
11X
13X
15X
17X
19X
21X
23X
2X
4X
6X
8X
10X
12X
14X
16X
18X
20X
22X
24X
100M LINK /
L /A
ACTIVITY
RS-232
TERMINAL PORT
10M LINK /
HALF DUP/
FULL DUP
D/C
STATUS
ACTIVITY
COL
1
3
5
7
9
11
13
15
17
19
21
23
2
4
6
8
10
12
14
16
18
20
22
24
FAULT
L /A
D/C
B
RPS
L /A
PWR
D/C
RESET
Campus 2: One AT-8224XL Switch
Figure 6 Back-to-Back Topology
11
Chapter 2
Installing the Media Converter
This chapter explains how to install an AT-MC1x Series Media Converter on a
desktop. To install the media converter in an AT-MCR12 chassis, refer to the
AT-MCR12 Installation Guide. This guide can be downloaded from our web
site at www.alliedtelesyn.com/support/prd_libs.htm.
Verifying Package Contents
Make sure the following items are included in your media converter package.
If any item is missing or damaged, contact your sales representative for
assistance.
q One AT-MC1x Series Ethernet Media Converter
q Four protective feet (for desktop use only)
q External AC/DC power adapter (North America, Continental Europe,
United Kingdom, or Australia)
q This installation guide
q Warranty card
Planning the Installation
Be sure to observe the following guidelines when planning the installation of
your media converter.
q The end-nodes connected to the media converter must operate at 10
Mbps.
q The end-nodes connected to the ports of the AT-MC13, AT-MC14, and
the AT-MC16 must be able to operate in the same duplex mode. These
units can operate in either full- or half-duplex mode.
q The end-nodes connected to the ports of the AT-MC15 must operate in
half-duplex mode.
13
q Refer to Table 5 for the twisted pair cabling specifications.
Table 5 Twisted Pair Port Specifications
Model
Cable
Maximum Operating Distance
All models
Shielded or unshielded Category 3
or better
100 m (328 ft)
q Refer to Table 6 for the thinnet cabling specifications.
Table 6 Thinnet Port Specifications
Model
Cable
Maximum Operating Distance
AT-MC15
Shielded or unshielded Category 3
or better
185 m (606 ft)
q Refer to Table 7 and Table 8 for the fiber optic cabling specifications.
Table 7 Fiber Optic Port Specifications (Full-duplex)
Model
Connector Cable
Maximum Operating
Distance
Maximum
Allowable Loss
Budget
AT-MC13
ST
62.5/125 micron
multimode
2 km (1.2 mi)1
20 dB at 850 nm
AT-MC14
SC
62.5/125 micron
multimode
2 km (1.2 mi)1
20 dB at 850 nm
AT-MC16
ST
9/125 micron
single-mode
15 km (9.3 mi)
13 dB at 1310 nm
1. Maximum operating distance over multimode fiber is 2 km (1.2 mi) if the maximum measured optical loss budget
is less than 20 dB’s when measured at 850 nm optical wavelength.
14
AT-MC1x Series Installation Guide
Table 8 Fiber Optic Port Specifications (Half-duplex)
Number of Media Converters
Connected Devices
Maximum Operating
Distance
One Media Converter Inline
Switch to Switch
372 m (1,221 ft)
Workstation to Switch
372 m (1,221 ft)
Switch to Class I Repeater
137 m (450 ft)
Switch to Class II Repeater
185 m (607 ft)
Switch to Switch
332 m (1,089 ft)
Workstation to Switch
332 m (1,089 ft)
Switch to Class I Repeater
97 m (318 ft)
Switch to Class II Repeater
145 m (476 ft)
Two Media Converters Inline
Reviewing Safety Precautions
Please review the following safety precautions before you begin to install the
media converter.
Caution
Power to the hub must be sourced only from the adapter. $ 5
Warning
(AT-MC13, AT-MC14) This is a “CLASS 1 LED PRODUCT” $ 7
(AT-MC16) Class 1 laser product. $ 8
Warning
Do not stare into the laser beam. $ 9
Warning
Lightning Danger: Do not work on equipment or cables during periods of
lightening activity. $ 10
Caution
Do not block air vents. $ 11
15
Caution
Operating Temperature
This product is designed for a maximum ambient temperature of 40
degrees C. $ 12
Caution
All Countries: Install product in accordance with local and National
Electrical Codes. $ 13
Installing the Media Converter
To install an AT-MC1x Series Media Converter, perform the following
procedure:
1.
Remove all equipment from the package and store the packaging material
in a safe place.
Note
Do not remove the dust cover from the fiber optic port until you are
ready to connect the fiber optic cable. Dust contamination can adversely
impact the operating performance of the port and the media converter.
2.
If you are installing the media converter on a desktop, attach the four
protective feet (provided) to each corner of the base of the unit. Do not
attach the rubber feet if you are installing the unit in an
AT-MCR12 chassis.
3.
If you are installing the media converter in an AT-MCR12 chassis, refer to
the chassis’ installation guide for instructions on how to install the unit,
then proceed to Step 5.
4.
Place the media converter on a level, secure surface (such as a desk or
table), leaving ample space around the unit for ventilation.
5.
For an AT-MC13, AT-MC14, or AT-MC16, remove the dust cover from the
fiber optic connector and connect the cable to the fiber optic port. Verify
that the near end-node transmitter port (TX) is connected to the far endnode receiver port (RX) and that the near end-node receiver port (RX) is
connected to the far end-node transmitter port (TX).
6.
For an AT-MC15, connect the thinnet cable to the 10Base2 port.
16
AT-MC1x Series Installation Guide
7.
Connect the twisted pair cable to the 10Base-T port.
8.
Set the MDI/MDI-X switch as follows:
9.
—
If you are connecting a workstation to the twisted pair port, set the
MDI/MDI-X switch to the MDI-X position. (MDI-X is the default
position.)
—
If you are connecting a hub or switch to the twisted port pair, set the
MDI/MDI-X switch to the MDI position.
Plug the AC/DC power adapter into an appropriate AC power outlet and
insert the power plug into the DC receptacle located on the back of the
unit. This step does not apply if you installed the unit in an
AT-MCR12 chassis.
12 V D C
Figure 7 12 V DC Connector on the Back of the Media Converter
10. Verify that the Power LED is green. If the LED is OFF, refer to
“Troubleshooting” on page 19 for instructions.
11. Power ON the end-nodes.
12. Verify that the LNK LED for both the fiber optic port and the twisted pair
port is green. The AT-MC15 has one LNK LED for the twisted pair port. If
the LED is OFF, refer to “Troubleshooting” on page 19 for instructions.
The media converter is now ready for use.
Warranty Registration
When you finish installing the product, register your product by completing the
enclosed warranty card and sending it in. You can also fill out the registration
online at www.alliedtelesyn.com/support/warrantyf.asp.
17
Chapter 3
Troubleshooting
Follow the guidelines below to test and troubleshoot the installation in the
event a problem occurs.
If the PWR LED is OFF, do the following:
q If the unit is installed on a desktop, check to be sure that the power
adapter is securely connected to a power outlet and that the power
adapter cable is securely connected to the back of the media converter.
q If the unit is installed in an AT-MCR12 chassis, check that the unit is
fully seated in the slot.
q Verify that the power outlet has power by connecting another device
to it.
q Try using another power adapter.
If the LNK LED for the twisted pair port is OFF, do the following:
q Check that the end-node connected to the port is powered ON and is
operating properly.
q Check that the twisted pair cable is securely connected to the twisted
pair port on the media converter and on the remote end-node.
q Make sure that the twisted pair cable does not exceed 100 meters (328
feet) and that you are using Category 3 or better cable.
q Verify that the end-node is operating at 10 Mbps and full- or
half-duplex mode if connected to an AT-MC13, AT-MC14, or
AT-MC16.
q Verify that the end-node is operating at 10 Mbps and half-duplex
mode if connected to an AT-MC15.
19
If the LNK LED for the fiber optic port is OFF, do the following:
q Verify that the end-node connected to the port is ON and is operating
properly.
q Check that the fiber optic cable is securely connected to the fiber optic
port on the media converter and on the remote end-node.
q Check to be sure that the end-node connected to the port is operating
at 10 Mbps.
q Make sure that the fiber optic port on the remote end-node is
operating in either full- or half-duplex mode.
q Make sure that the cable connected to the fiber optic receiver port on
the media converter is connected to the transmitter port on the remote
end-node and that the fiber optic transmitter port on the media
converter is connected to the receiver port on the end-node.
q Test the attenuation on the fiber cable to ensure that it does not
exceed acceptable values.
q Verify that you are using the appropriate type of fiber optic cable and
that you have not exceeded the maximum operating distance. For
cable types and operating distances, refer to Table 7 on page 14 and
Table 8 on page 15.
q Check that the operating specifications (e.g., wavelength and
maximum operating distance) of the fiber optic port on the end-node
are compatible with the operating specifications of the fiber optic port
on the media converter. See Table 7 on page 14 for fiber optic port
specifications.
20
AT-MC1x Series Installation Guide
If the LNK LED for the fiber optic port is ON, but there is a communication
problem between the end-nodes connected to the media converter (and you are
not running a Fiber Link Test), check the following:
q Check that the end-nodes connected to the ports are operating at 10
Mbps.
q Check that the end-nodes connected to the AT-MC13, AT-MC14, or
AT-MC16 are operating in the same duplex mode. These units can
operate in either full- or half-duplex mode.
q Check that the Fiber Link Test switch on the media converter is in the
DOWN position.
q Check that the maximum allowable loss budget for the fiber optic
cable has not been exceeded. Refer to Table 7 on page 14 for the fiber
optic port specifications.
If the NML LED on the AT-MC13, AT-MC14, or AT-MC16 is OFF, do the
following:
q Check that the end-nodes connected to the media converter are
powered ON.
q Check that the fiber optic cable is securely connected to the fiber optic
port.
q Verify that the appropriate fiber optic cable is being used. Refer to
Table 7 on page 14 and Table 8 on page 15 for the fiber optic cable
specifications.
q Verify that the maximum allowable loss budget for the fiber optic
cable has not been exceeded.
If you are still experiencing problems after troubleshooting the installation,
contact Allied Telesyn Technical Support for assistance. Refer to “Contacting
Allied Telesyn Technical Support” on page viii or visit our web site at
www.alliedtelesyn.com for support information.
21
Appendix A
Technical Specifications
Physical
Dimensions (W x D x H):
10.5 cm x 9.5 cm x 2.5 cm
(4.1 in x 3.7 in x 1.0 in)
Weight:
294 g (10.4 oz)
Temperature
Maximum Operating:
0° C to 40° C (32° F to 104° F)
Maximum Storage:
-25° C to 70° C (-13° F to 158° F)
Relative Humidity:
5% to 95% non-condensing
Operating Altitude:
Up to 3,048 meters (10,000 feet)
Electrical Rating
Input Supply Voltage:
12 V DC ± -5%
Maximum Current:
.5
Power Consumption:
6W
AC Input Voltage:
AT-MC13, AT-MC14, AT-MC16 500 mA
AT-MC15
300 mA
23
Agency Certifications
EMI/RFI:
FCC Class A, IC Class A, EN 55022 Class B
Safety:
UL, CSA, TUV, IEC 825-1 CE Compliant
Immunity:
EN50082-1 1997 Immunity Standard
24
Appendix B
Translated Safety and Emission Information
Important: This appendix contains multiple-language translations for the
safety statements in this guide.
Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.
Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi
di sicurezza di questa guida.
Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.
Importante: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.
Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.
25
Translated Safety and Emission Information
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International Corp.
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet Media Converters
Model Numbers:
AT-MC13, AT-MC14, AT-MC15, AT-MC16
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device must not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on. The user is encouraged to try to correct
the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer
or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
26
AT-MC1x Series Installation Guide
Warning: In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate
measures.
$1
RFI Emission
EN55022 Class B
$2
Immunity
EN55024
$3
Warning (AT-MC13, AT-MC14, AT-MC16): This product requires shielded cables
to comply with emission and immunity standards. If it is used with
unshielded cables, the user may be required to take measures to correct the
interference problem at their own expense.
$4
Electrical Safety
TUV-EN60950, UL1950, CSA 950
SAFETY
$5
Power to the hub must be sourced only from the adapter.
EUROPE—EC (AT-MC13, AT-MC14, AT-MC16)
Use TÜV licensed AC adapter of 12 V DC, min 500 mA.
EUROPE—EC (AT-MC15)
Use TÜV licensed AC adapter of 12 V DC, min 300 mA.
OTHER COUNTRIES (AT-MC13, AT-MC14, AT-MC16)
Use a Safety Agency Approved AC adapter of 12 V DC, min 500 mA.
OTHER COUNTRIES (AT-MC15)
Use a Safety Agency Approved AC adapter of 12 V DC, min 300 mA.
$6
Laser
$7
This is a “CLASS 1 LED PRODUCT” (AT-MC13, AT-MC14)
$8
Warning (AT-MC16): Class 1 Laser product.
$9
Warning: Do not stare into the Laser beam.
EN60825
At time of installation the Fiber Optic Lasers comply with FDA Radiation
Performance Standard 21CFR Subchapter J, applicable at date of
manufacture.
Caution: Power cord is used as a disconnection device. To de-energise
equipment disconnect the power cord.
$ 10
LIGHTNING DANGER
Danger: Do not work on equipment or cables during periods of lightning
activity.
$ 11
Do not block air vents.
27
Translated Safety and Emission Information
Do not connect a telephone line into the signal connector.
$ 12
Operating Temperature: This product is designed for a maximum ambient
temperature of 40 degrees C.
$ 13
All Countries: Install product in accordance with local and National
Electrical Codes.
Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden
Normen.
$1
Hochfrequenzstörung
EN55022 Klasse B
$2
Störsicherheit
EN55024
$3
Achtung (AT-MC13, AT-MC14, AT-MC16): Für dieses Produkt sind abgeschirmte Kabel
erforderlich, damit den Richtlinien für Emission und Interferenzschutz
entsprochen wird. Falls das Produkt mit nicht abgeschirmten Kabeln
verwendet wird, können weitergehende Maßnahmen für die Korrektur von
Interferenzproblemen auf Kosten des Benutzers notwendig werden.
$4
Elektrische Sicherheit
TUV-EN60950, UL1950, CSA 950
SICHERHEIT
$5
Der Buchse darf nur aus dem Adpater Strom zugeführt werden.
EUROPE—EC (AT-MC13, AT-MC14, AT-MC16)
Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für
Gleichstrom 12 Vdc, 500 mA.
EUROPE—EC (AT-MC15)
Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für
Gleichstrom 12 Vdc, 300 mA.
$6
Laser
$7
Das ist ein “LED Produkt der Klasse 1” (AT-MC13, AT-MC14)
$8
Warnung (AT-MC16): Laserprodukt der Klasse 1.
$9
Warnung: Nicht direkt in den Strahl blicken.
EN60825
Vorsicht: Das netzkabel dient zum trennen der stromversorgung. Zur
trennung vom netz, kabel aus der steckdose ziehen.
$ 10
GEFAHR DURCH BLITZSCHLAG
Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines
Gewitters ausführen.
$ 11
Entlüftungsöffnungen nicht versperren.
28
AT-MC1x Series Installation Guide
Verbinden Sie nicht das Telefonkabel mit dem Signalverbindungsstecker.
$ 12
Betriebstemperatur: Dieses Produkt wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 40° C entworfen.
$ 13
Alle Länder: Installation muß örtlichen und nationalen elektrischen
Vorschriften entsprechen.
Standarder: Dette produkt tilfredsstiller de følgende standarder.
$1
Radiofrekvens forstyrrelsesemission EN55022 Klasse B
$2
Immunitet
$3
Advarsel (AT-MC13, AT-MC14, AT-MC16): Dette produkt skal bruges med
afskærmede kabler for at overholde bestemmelserne vedrørende udstråling
og støjimmunitet. Hvis det bruges med uafskærmede kabler, kan det blive
påkrævet af brugeren at korrigere interferensproblemer for egen regning.
$4
Elektrisk sikkerhed
EN55024
TUV-EN60950, UL1950, CSA 950
SIKKERHED
$5
Strømforsyningen til apparatet må udelukkende tages fra
tilpasningstransformatoren.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Brug kun TÜV godkendt vekselstrømstransformator på 12 Vdc, 500 mA.
EUROPE - EC (AT-MC15)
Brug kun TÜV godkendt vekselstrømstransformator på 12 Vdc, 300 mA.
$6
Laser
$7
Dette er et “PRODUKT UNDER KLASSE 1 LED” (AT-MC13, AT-MC14)
$8
Advarsel (AT-MC16): Laserprodukt av klasse 1.
$9
Advarsel: Stirr ikke på strålen.
EN60825
Advarsel: DEN STRØMFØRENDE LEDNING BRUGES TIL AT
AFBRYDE STRØMMEN. SKAL STRØMMEN TIL APPARATET
AFBRYDES, tages ledningen ud af stikket.
$ 10
FARE UNDER UVEJR
Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
$ 11
Ventilationsåbningerne må ikke blokeres.
Tilslut ikke telefonledninger til signalstikforbindelsen.
29
Translated Safety and Emission Information
$ 12
Betjeningstemperatur: Dette apparat er konstrueret til en omgivende
temperatur på maksimum 40 grader C.
$ 13
Alle Lande: Installation af produktet skal ske i overensstemmelse med
lokal og national lovgivning for elektriske installationer.
Eisen: Dit product voldoet aan de volgende eisen.
$1
RFI Emissie
EN55022 Klasse B
$2
Immuniteit
EN55024
$3
Waarschuwing (AT-MC13, AT-MC14, AT-MC16): Om te voldoen aan de emissie- en
immuniteitsnormen dient dit apparaat te zijn voorzien van afgeschermde
kabels. Als het met niet-afgeschermde kabels wordt gebruikt, kan het zijn
dat de gebruiker maatregelen moet treffen om interferentieproblemen voor
eigen rekening op te lossen.
$4
Electrische Veiligheid
TUV-EN60950, UL1950, CSA 950
VEILIGHEID
$5
Stroom mag alleen via de adapter naar het apparaat toegevoerd worden.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Gebruik een door TÜV gekeurde wisselstroomadapter van 12 Vdc, 500 mA.
EUROPE - EC (AT-MC15)
Gebruik een door TÜV gekeurde wisselstroomadapter van 12 Vdc, 300 mA.
$6
Laser
$7
Dit is een “KLASSE 1 LED-PRODUKT” (AT-MC13, AT-MC14)
$8
Waarshuwing (AT-MC16): Klasse-1 laser produkt.
$9
Waarchuwing: Neit in de straal staren.
EN60825
Waarschuwing: HET TOESTEL WORDT UITGESCHAKELD DOOR DE
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL
STROOMLOOS TE MAKEN: de stroomkabel ontkoppelen.
$ 10
GEVAAR VOOR BLIKSEMINSLAG
Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
$ 11
Ventilatiegaten niet blokkeren.
Sluit geen telefoonlijn aan op de signaalverbinding.
30
AT-MC1x Series Installation Guide
$ 12
Bedrijfstemperatuur: De omgevingstemperatuur voor dit produkt mag
niet meer bedragen dan 40 graden Celsius.
$ 13
Alle Landen: het toestel installeren overeenkomstig de lokale en
nationale elektrische voorschriften.
Normes: ce produit est conforme aux normes de suivantes.
$1
Eemission d’interférences
radioélectriques
EN55022 Classe B
$2
Immunité
EN55024
$3
Avertissement (AT-MC13, AT-MC14, AT-MC16): Il faut utiliser des câbles blindés pour
ce produit afin de respecter les normes d’émission et d’immunité. Si
l’utilisateur choisit d’utiliser des câbles non blindés, il sera peut-être
contraint de prendre les mesures nécessaires pour corriger les problèmes
d’interférences, ainsi que d’assumer le coût correspondant.
$4
Sécurité électrique
TUV-EN60950, UL1950, CSA 950
SÉCURITÉ
$5
L’alimentation du concentrateur doit être uniquement fournie par
l’adaptateur.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Utiliser un adaptateur secteur conforme TÜV de 12 V dc, 500 mA en
courant continu.
EUROPE - EC (AT-MC15)
Utiliser un adaptateur secteur conforme TÜV de 12 V dc, 300 mA en
courant continu.
$6
Laser
$7
Ce matériel est un “PRODUIT À DIODE ÉLECTROLUMINESCENTE DE
CLASSE 1” (AT-MC13, AT-MC14)
$8
Attention (AT-MC16 ): Producit laser di classe 1.
$9
Attention: Ne pas fixer le faisceau des yeux.
EN60825
Attention: LE CORDON D’ALIMENTATION SERT DE MISE HORS
CIRCUIT. POUR COUPER L’ALIMENTATION DU MATÉRIEL,
débrancher le cordon.
$ 10
DANGER DE FOUDRE
Danger: NE PAS MANIER le matériel ou les CÂBLES lors d’activité
orageuse.
31
Translated Safety and Emission Information
$ 11
Ne pas bloquer les fentes d’aération.
Ne pas connecter une ligne téléphonique au connecteur de signaux.
$ 12
Température De Fonctionnement: Ce matériel est capable de tolérer
une température ambiante maximum de 40 degrés Celsius.
$ 13
Pour Tous Pays: Installer le matériel conformément aux normes
électriques nationales et locales.
Standardit: Tämä tuote on seuraavien standardien mukainen.
$1
Radioaaltojen häirintä
EN55022 Luokka B
$2
Kestävyys
EN55024
$3
Varoitus (AT-MC13, AT-MC14, AT-MC16): Tämä tuote vaatii suojattuja
kaapeleita toimiakseen emissio- ja häiriönsietostandardien mukaisesti. Jos
tuotetta käytetään ilman suojattuja kaapeleita, käyttäjä voi joutua
korjaamaan häirinnän aiheuttaman ongelman omalla kustannuksellaan.
$4
Sähköturvallisuus
TUV-EN60950, UL1950, CSA 950
TURVALLISUUS
$5
Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan
sovittimesta.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat 12 Vdc, 500 mA (milliampeeria).
EUROPE - EC (AT-MC15)
Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat 12 Vdc, 300 mA (milliampeeria).
$6
$7
Laser
EN60825
Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE” (AT-MC13,
AT-MC14)
$8
Varoitus (AT-MC16): Luokan 1 Lasertuote.
$9
Variotus: Älä katso säteeseen.
Huomautus: VIRTAJOHTOA KÄYTETÄÄN
VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla
virtajohto.
32
AT-MC1x Series Installation Guide
$ 10
SALAMANISKUVAARA
Hengenvaara: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN
KANSSA SALAMOINNIN AIKANA.
$ 11
Älä tuki ilmareikiä
Älä liitä puhelinlinjaa signaalin liittimeen.
$ 12
Käyttölämpötila: Tämä tuote on suunniteltu ympäröivän ilman
maksimilämpötilalle 40° C.
$ 13
Kaikki Maat: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
Standard: Questo prodotto è conforme ai seguenti standard.
$1
$2
$3
$4
Emissione RFI (interferenza di
radiofrequenza)
EN55022 Classe B
Immunità
EN55024
(AT-MC13, AT-MC14, AT-MC16): questo prodotto, se utilizzato con cavi
schermati, è conforme alle norme sulle emissioni e sull’immunità. In caso
di uso senza cavi schermati, l’utente può dover adottare a proprie spese
misure correttive contro le interferenze.
Avvertenza
Sicurezza elettrica
TUV-EN60950, UL1950, CSA 950
NORME DI SICUREZZA
$5
Questo dispositivo deve essere alimentato solo mediante l’adattatore.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Utilizzare l’adattatore per c.a. da 12 Vdc, 500 mA conforme alla normativa
TÜV.
EUROPE - EC (AT-MC15)
Utilizzare l’adattatore per c.a. da 12 Vdc, 300 mA conforme alla normativa
TÜV.
$6
Laser
$7
Questo è un “PRODOTTO CON LED DI CLASSE 1” (AT-MC13, AT-MC14)
$8
Avvertenza
$9
Avertenza: Non fissare il raggio con gli occhi.
EN60825
(AT-MC16) :
Prodotto laser di Classe 1.
Attenzione: IL CAVO DI ALIMENTAZIONE È USATO COME
DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE
AL DISPOSITIVO staccare il cavo di alimentazione.
33
Translated Safety and Emission Information
$ 10
PERICOLO DI FULMINI
Pericolo: NON LAVORARE sul dispositivo o sui CAVI durante
PRECIPITAZIONI TEMPORALESCHE.
$ 11
Non ostruire le prese d’aria.
Non collegare una linea telefonica al connettore del segnale.
$ 12
Temperatura Di Funzionamento: Questo prodotto è concepito per una
temperatura ambientale massima di 40 gradi centigradi.
$ 13
Tutti I Paesi: installare il prodotto in conformità delle vigenti normative
elettriche nazionali.
Sikkerhetsnormer: Dette produktet tilfredsstiller følgende
sikkerhetsnormer.
$1
RFI stråling
EN55022 Klasse B
$2
Immunittet
EN55024
$3
Advarsel (AT-MC13, AT-MC14, AT-MC16): Dette produktet må brukes med
vernede kabler for å tilfredsstille emisjons- og fritakelsesstandarder.
Dersom produktet brukes med uvernede kabler, må brukeren muligens
rette forstyrrelsesproblemene for egen regning.
$4
Elektrisk sikkerhet
TUV-EN60950, UL1950, CSA 950
SIKKERHET
$5
All strømtilførsel må komme fra adapteren.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Benytt TÜV-godkjent AC-adapter på 12 Vdc, 500 mA (milliampere).
EUROPE - EC (AT-MC15)
Benytt TÜV-godkjent AC-adapter på 12 Vdc, 300 mA (milliampere).
$6
Laser
$7
Dette er et “KLASSE 1 LED PRODUKT” (AT-MC13, AT-MC14)
$8
Advarsel (AT-MC16): Laserprodukt Av Klasse 1.
$9
Advarsal: Stirr ikke på strålen.
EN60825
Forsiktig: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE
UTSTYRET. FOR Å DEAKTIVISERE UTSTYRET, må strømforsyningen
kobles fra.
34
AT-MC1x Series Installation Guide
$ 10
FARE FOR LYNNEDSLAG
Fare: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
$ 11
Blokker ikke luftventilene.
Telefonlinje må ikke koples til signalkontakten.
$ 12
Driftstemperatur: Dette produktet er konstruert for bruk i maksimum
romtemperatur på 40 grader celsius.
$ 13
Alle Land: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
Padrões: Este produto atende aos seguintes padrões.
$1
Emissão de interferência de
radiofrequência
EN55022 Classe B
$2
Imunidade
EN55024
$3
Advertência (AT-MC13, AT-MC14, AT-MC16): Este produto requer a utilização
de cabos blindados para cumprimento dos standards de limites de emissão
e imunidade. Se o produto for utilizado com cabos não blindados, o
utilizador poderá necessitar de tomar medidas para correcção de problemas
de interferência, por sua própria conta.
$4
Segurança eléctrica
TUV-EN60950, UL1950, CSA 950
SEGURANÇA
$5
Use somente o adaptador fornecido para alimentação elétrica do hub.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Use um adaptador de corrente alternada com saída DC de 12 Vdc, 500 mA
em conformidade com as especificações da TÜV.
EUROPE - EC (AT-MC15)
Use um adaptador de corrente alternada com saída DC de 12 Vdc, 300 mA
em conformidade com as especificações da TÜV.
$6
Laser
$7
Este é um “PRODUTO CLASSE 1 LED” (AT-MC13, AT-MC14, AT-MC16)
$8
AVISO (AT-MC16): Produto laser de classe 1.
$9
AVISO: Não olhe fixamente para o raio.
EN60825
Cuidado: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O
EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO.
35
Translated Safety and Emission Information
$ 10
PERIGO DE CHOQUE CAUSADO POR RAIO
Perigo: NÃO TRABALHE no equipamento ou nos CABOS durante
períodos suscetíveis a QUEDAS DE RAIO.
$ 11
Não bloqueie as aberturas de ventilação.
Não conecte uma linha telefônica ao conector de sinal.
$ 12
Temperatura De Funcionamento: Este produto foi projetado para uma
temperatura ambiente máxima de 40 graus centígrados.
$ 13
Todos Os Países: Instale o produto de acordo com as normas nacionais e
locais para instalações elétricas.
Estándares: Este producto cumple con los siguientes estándares.
$1
Emisión RFI
EN55022 Clase B
$2
Inmunidad
EN55024
$3
Advertencia: Este producto exige cables protectores para ajustarse a las
normas de emisión e inmunidad. Si se utiliza con cables sin protección, el
usuario tendrá que correr con los gastos por las medidas a tomar en caso de
problemas de interferencias.
$4
Seguridad eléctrica
TUV-EN60950, UL1950, CSA 950
SEGURIDAD
$5
La energía para el dispositivo central o “hub” debe provenir únicamente del
adaptador.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Utilizar un adaptador de corriente alterna autorizado TÜV de 12 Vdc, 500
mA.
EUROPE - EC (AT-MC15)
Utilizar un adaptador de corriente alterna autorizado TÜV de 12 Vdc, 300
mA.
$6
$7
Laser
EN60825
Este es un “Producto De Diodo Luminiscente (LED) Clase 1” (AT-MC13,
AT-MC14)
$8
¡Advertencia! (AT-MC16) Producto láser Clase 1.
$9
¡Advertencia! No mirat fijamente el haz.
36
AT-MC1x Series Installation Guide
Atencion: EL CABLE DE ALIMENTACION SE USA COMO UN
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO,
desconecte el cable de alimentación.
$ 10
PELIGRO DE RAYOS
Peligro: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en
los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
$ 11
No bloquee las aberturas para ventilacion.
No conectar ninguna línea telefónica al conector de señales.
$ 12
Temperatura Requerida Para La Operación: Este producto está
diseñado para una temperatura ambiental máxima de 40 grados C.
$ 13
Para Todos Los Países: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
Standarder: Denna produkt uppfyller följande standarder.
$1
Radiostörning
EN55022 Klass B
$2
Immunitet
EN55024
$3
Varning (AT-MC13, AT-MC14, AT-MC16): Denna produkt kräver skärmade kablar för
att uppfylla standardkraven för emission och immunitet. Om den används
med oskärmade kablar kan användaren vara tvungen att vidta åtgärder på
egen bekostnad för att åtgärda störningsproblemet.
$4
Elsäkerhet
TUV-EN60950, UL1950, CSA 950
SÄKERHET
$5
Endast anslutningsenheten får vara kraftkälla till centralen.
EUROPE - EC (AT-MC13, AT-MC14, AT-MC16)
Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 12
Vdc, 500 mA.
EUROPE - EC (AT-MC15)
Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 12
Vdc, 300 mA.
$6
Laser
$7
Detta är en “KLASS 1 LYSDIODPRODUKT” (AT-MC13, AT-MC14)
$8
Varning! (AT-MC16) Laserprodukt av klass 1.
$9
Varning! Laserstrålning när enheten är öppen.
EN60825
37
Translated Safety and Emission Information
Varning: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT
KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.
$ 10
FARA FÖR BLIXTNEDSLAG
Fara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
$ 11
Blockera inte luftventilerna.
Koppla inte telefonledning till signalkontakten.
$ 12
Driftstemperatur: Denna produkt är konstruerad för rumstemperatur ej
överstigande 40 grader Celsius.
$ 13
Alla Länder: Installera produkten i enlighet med lokala och statliga
bestämmelser för elektrisk utrustning.
38
Appendix C
Technical Support Fax Order Form
Name _________________________________________________________________
Company ______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province_______________________________
Zip/Postal Code _________________ Country_______________________________
Phone ______________________________ Fax_______________________________
Incident Summary
Model number of Allied Telesyn product I am using _______________________
Network software products I am using (e.g., network managers)
______________________________________________________________________
______________________________________________________________________
Brief summary of problem
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Conditions (List the steps that led up to the problem.)
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Detailed description (Use separate sheet, if necessary)
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
When completed, fax this sheet to the appropriate Allied Telesyn office. Fax
numbers can be found on page viii.
39