Centrality PA168 Series IP Phone PPPoE Configuration

Centrality PA168 Series IP Phone PPPoE Configuration Guide
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Now more and more ADSL, Cable Modem and Ethernet Broadband access
users connect Internet with PPPoE protocol. This guide supplies a
step-by-step operation on how to install and configure Centrality PA168 series
IP Net Phone to ADSL, Cable Modem users.
1. Install the IP Phone (Take PA168S IP phone as example):
1.1. Insert handset cord into handset cord jack at the left side of the base
to connect the handset to the base. Refer to Fig 1.1 please.
Handset cord Jack
20
18 19
Fig 1.1 Connect the Handset and the Base of the Phone
1.2. Plug the power adapter cord into the Power Jack. Then plug the other
end of the power cord adapter into the appropriate wall outlet. Refer
to Fig 1.2 please.
Beijing Centrality Communications Co., Ltd
1
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Power Adapter
Switch
Power Jack
Wall Outlet
Fig 1.2 Connect Power Adapter to the Phone
1.3. Turn on the Phone: Turn on the phone by pulling the power switch to
ON. Verify that No.18, 19 and 20 lights are on together, and then
No.18 light is off; No.19 light blinks or is off ; No. 20 light blinks or is
on.
1.4. Pick up the handset or press
Speaker
, the dialed tone indicates
that the phone starts successfully and is ready for call.
Note Please use the special power adapter packaged with Centrality PA168 series IP
phone. The voltage is alternating current 220V, 50Hz.
2. Check and note the IP address of PC used to set the phone.
1) Choose Start>Run, please refer to Fig 2.1.
Beijing Centrality Communications Co., Ltd
2
Centrality PA168 Series IP Phone PPPoE Configuration Guide
2) In popup Run dialog, input cmd into Open field and click OK button,
then DOS window will be displayed. Refer to Fig 2.2 and 2.3 please.
Note If the PC’s OS is WinXP/2000/NT, please input cmd; if PC’s OS is Win9X,
please input command。
Fig 2.1 Choose Start>Run
Fig 2.2 Enter DOS Window
Fig 2.3 DOS window
Fig 2.4 Run ipconfig Command
3) In DOS window, input ipconfig/all and press Return. Refer to Fig 2.4.
Note If the PC’s OS is WinXP/2000/NT, please use ipconfig/all command; if PC’s
OS is Win9X, please use ipconfig command。
4) The configuration of PC net adapter will be displayed. Refer to Fig 2.5
Beijing Centrality Communications Co., Ltd
3
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Fig2.5 Check the IP address of PC on WinXp/2000/NT OS
3. Check the configured state of the IP phone: With the phone turned on
press
Local IP
, then you will hear the voice prompted IP address of the
phone:
¾ If the voice prompted IP address is 0.0.0.0, it indicates that DHCP is
enabled but the phone is not assigned IP address. Please do as
follows to disable DHCP and then set IP address manually.
1) Press
Speaker
or pick up the handset, and then input the
password of the phone. When No 18 light begins blinking once a
second, please go to the next step.
Beijing Centrality Communications Co., Ltd
4
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Note Press Speaker key or pick up the handset and then input the password of the
phone. Verify that No 18 light blinks once a second. It indicates that the
phone is under setting mode
The default password of Centrality PA168 series IP phone is 1234.
2) Press
0
and
Local IP
, then the phone will restart. Verify
that No.18, 19 and 20 lights are on together, and then No.18 light
is off; No.19 light blinks or is off ; No. 20 light blinks or is on. As
soon as the phone restarts successfully, DHCP is disabled.
3) Repeat step 1) to make phone enter setting mode again.
4) Set the IP address of the phone manually: Designate an IP
address such as 192.168.1.100 to the phone. Press 192*168*1*
100 keys on the keypad orderly, and then pressing
Local IP
.
5) As soon as the phone restarts successfully, please go to step 3.
¾ If the voice prompted IP address is 255.255.255.255, it indicates that
PPPoE is enabled but the phone Dial-up unsuccessfully. Then please
do as follows to disable PPPoE and then set IP address manually.
1) Press
Speaker
or pick up the handset, and then input the
password of the phone. When No 18 light begins blinking once a
second, please go to the next step.
2) Press
0
and
Local IP
Beijing Centrality Communications Co., Ltd
, then the phone will restart. As soon
5
Centrality PA168 Series IP Phone PPPoE Configuration Guide
as the phone restarts successfully, PPPoE is disabled.
3) Repeat step 1) to make phone enter setting mode again.
4)
Set the IP address of the phone manually: Designate an IP
address such as 192.168.1.100 to the phone. Press 192*168*1*
100 keys on the keypad orderly, and then pressing
Local IP
.
5) As soon as the phone restarts successfully, please go to step 3.
¾ If the voice prompted IP address is neither 0.0.0.0 nor 255.255.255.
255, it indicates that the phone is assigned an IP address
successfully. Please take a note of the address and go to the next
step. We take 192.168.1.100 as an example.
4. Prepare Cross Cable: Pull out the cross cable from the ADSL Modem or
Cable Modem. Please refer to Fig 3.
Cross Cable
Fig 3 Prepare Cross Cable
If your ADSL Modem has USB interface, please prepare cross cable by
yourself.
5. Connect PC and the IP phone: Insert one end of the cross cable into RJ-45
Beijing Centrality Communications Co., Ltd
6
Centrality PA168 Series IP Phone PPPoE Configuration Guide
cord jack of the phone, and then insert the other end into the Ethernet
interface of PC. Refer to Fig 4 please.
Cross cable
RJ-45 Jack
Fig 4 Connect PC and the IP phone with Cross Cable
If you get a HUB, you can use an Ethernet cable to linking the phone to the net
directly by connecting HUB, phone and PC, and then connecting HUB and
ADSL Modem. Refer to following fig:
Ethernet cable
ADSL Modem or Cable Modem
HUB
6. Have completed above operation, please configure the phone as follows:
6.1. Open the setting tool: on a computer in the same segment with the phone,
double click
icon to open the PalmTool. Then input IP address of
the phone into local IP address field (such as 192.168.1.100), then
click phone setting button. The setting page of the phone will be
Beijing Centrality Communications Co., Ltd
7
Centrality PA168 Series IP Phone PPPoE Configuration Guide
displayed.
Note Please visit http://www.aredfox.com/download/tools/PalmTool.zip to download
PalmTool, if you have not installed it.
Note From version1.24, when Debug set as 0[disable], PalmTool can not connect to
the IP phone directly. Then please set Debug as other value. When use above
mentioned two methods to set IP phone, please use super password 19750407
to login to the configuration page. If this password is invalid, please ask phone
provider for a valid one.
6.2. PPPoE set:Select pppoe in iptype dropdown list. Fill ADSL account
into ppp id field; and then fill ADSL password into ppppin field.
Set protocol service: according to different protocol, set different service. Refer
to following context to get detailed operation:
a) H323 protocol:When H323 protocol is used, the relevant parameters
are use service, service addr, service port and phone number.
① Set protocol service: With H323 protocol used, the protocol service
refers to login the gatekeeper. Gatekeeper is the key component of
H.323 protocols regulated by ITU-T. It provides an address translation
service. With H323 protocol used, when you want to call other IP
phone by dialing phone number instead of IP address, please check
use service option and then type IP address or domain name of the
Beijing Centrality Communications Co., Ltd
8
Centrality PA168 Series IP Phone PPPoE Configuration Guide
GK into service addr field.
Note If you have not got any gatekeeper, we suggest you to run a free gatekeeper
based on open resource. Please visit www.gnugk.org or www.openh323.org to
download a program and then run it on a PC with public IP. Please take a note
of the IP address of this PC and then fill it into service ip address field.
② Set service port: With gatekeeper used, please set serviceport as
1719
.
Note With H323 protocol used, the IP phone are allowed to log in the gateway by
being set as follows: uncheck use service option; then fill the IP address of
gateway into service addr field; then set service port as 1720.
③ Set phone number: Enter a 7 or 8 digit number into phone number
field
.
Note Without gatekeeper or gateway used, the IP phone can communicate with other
IP phone or H323 terminal (such as Microsoft Netmeeting 3.01) with public IP
address. The operation is as follows: Pick up the handset or press Speaker, and
then use the keypad to enter the IP address of the other party. Please use”*”to
replace “.”. For example, the IP address of the device you wish to call is
166.111.19.88, please press 166*111*19*98 in order on the keyboard, and then
press Call or # to place the call. Once the call connection has been established and
the ring tone has sounded, wait for the other party to answer.
2) MGCP protocol:With MGCP protocol used, the relevant parameters are
Beijing Centrality Communications Co., Ltd
9
Centrality PA168 Series IP Phone PPPoE Configuration Guide
use service, service addr, service port, register port, account and pin.
① Set protocol service: With MGCP protocol used, the protocol service
refers to log in Call Agent. Please check the use service option and
then fill the IP address or domain name of the CA into service addr
field (such as 211.98.66.43).
② Set receive port of Call Agent:the default port is 2727;so please set
service port as 2727。
③ Set information sent port: the default port is 2427;so please set
register port as 2427。
④ Set EndpointID:EndpointID is used to identify gateway and port of
gateway. It includes two parts: Local name and Domain name. Local
name used to identify different ports of one gateway; while Domain
name used to identify gateway, it could be string or IP address of
gateway. “LocalName @ DomainName” consists an EndpointID。
Please type the Local name and Domain name into account and pin
fields respectively.
⑤ Set phone number: Enter a number into phone number field.
3) SIP protocol:With SIP protocol used, the relevant parameters are use
service, service addr, phone number, service port and register port.
Beijing Centrality Communications Co., Ltd
10
Centrality PA168 Series IP Phone PPPoE Configuration Guide
① Set protocol service: with SIP protocol used, the protocol service
refers to Proxy Server. Please check use service option according to
system and then enter the IP address or domain name of SIP Proxy
Server into the service addr field.
② Set service port: enter the default port 5060 into service port field.
③ Set register port: enter the default port 5060 into register port field.
④ Set Local ID:Fill Local ID into phone number field.
4) Net2phone protocol:With Net2phone private protocol used, the relevant
parameters are use service, service addr, service port, account and pin.
① Set protocol service: with Net2phone private protocol used, the phone
should login the designated server. Please check use service option.
② Set service addr: please fill 216.53.3.52; 4.43.114.39; 205.228.245.8
or 4.43.114.38, or call1.net2phone.com ; call2.net2phone.com ;
skip1.net2phone.com or skip2.net2phone.com into service addr field.
③ Set servieport: fill the default number 6801 into serviceport field.
④ Set account: fill the account (such as 13801038908) into account field.
⑤ Set pin: fill the pin (such as 7085) into pin field.
Beijing Centrality Communications Co., Ltd
11
Centrality PA168 Series IP Phone PPPoE Configuration Guide
6.3. Enable multi-settings: From released version 1.08, the setting of IP phone
is changed. More than one sets of parameters can be saved into the
SDRAM of the IP phone. Usually the phone uses current settings to call
out. With switch selected in use inner line dropdown list, the user can use
backup settings 1 and backup settings 2 by dialing the number
designated in local prefix and nonlocal prefix. Then the users can place
calls using backup settings by switching between multi-settings without
changing the settings.
Note When PA168S IP phone is used, 5 settings are saved in the phone,
multi-settings allows you to switch between different system and operation.
multi-settings Features only support H323 protocol.
Save current settings: click
button to confirm the configuration.
Once the phone restarts auto, current setting is saved into the phone.
★
As for those IP phone with LCD, beside above methods to set the phone
on computer, it also allowed to be set with keypad as follows:
a) Using keypad to input the password of the IP phone and then
press
#
, till
Password:
is displayed on the LCD. Then please
input the password of the phone again and press
Speaker
to enter
setting mode.
Beijing Centrality Communications Co., Ltd
12
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Note From version1.24, when Debug set as 0[disable], please use super password
19750407 to enter configuration mode. If this password is invalid, please ask
phone provider for a valid one.
network
b) Enable PPPoE mode: When LCD displays
by pressing
Speaker
menu till LCD displays
settings
; and then press
ip type
0[static]
Vol+
; then press
, enter sub menu
to turn over the
Local IP
, then you
will see a cursor flashes at the beginning of the second line. Please
press
2
and
Speaker
to enable PPPoE. Once
ip type
2[pppoe]
is
displayed on LCD, it indicates that you have done it successfully.
c) Set PPPoE account: Continue pressing
till
ppp id
Vol+
to turn over the menu,
is displayed on LCD, and then press
Local IP
to
enter change mode. Once a cursor flashes at the beginning of the
second line, please input ADSL user name with keypad, take test1 as
an example, press 8 key twice, 3 key thrice, 7 key five times, 8 key twice
and 1 key once; and then press
displays
ppp id
test1
to confirm. Once LCD
, it indicates that you have done it successfully.
d) Set PPPoE pin: Continue pressing
LCD displays
Speaker
ppp pin
Vol+
, and then press
to turn over the menu, till
Local IP
to enter change
mode. Once a cursor flashes at the beginning of the second line, please
input ADSL password with keypad, take test1 as an example, press 8
key twice, 3 key thrice, 7 key five times, 8 key twice and 1 key once; and
Beijing Centrality Communications Co., Ltd
13
Centrality PA168 Series IP Phone PPPoE Configuration Guide
then press
Speaker
to confirm. Once LCD displays
ppp pin
test1
, it
indicates that you have done it successfully.
Note To change case of input characters, please press # once after press Local IP.
e) Enter protocol sub menu: press
network
menu; once
Redial
key to exit networking setting
is displayed again, press
settings
to protocol setting menu
protocol
settings
, then press
Vol+
to turn over
Speaker
to enter it.
f) Set protocol (take H323 as example): Once you enter protocol setting
menu, you will see protocol setting sub menu. If current protocol is
H323, that is to say, if
protocol
is displayed on LDC, press
0[h323]
the next menu; if current protocol is not H323, press
change mode and then press
0
and
Speaker
Local IP
Vol+
to
to enter
to set the protocol
as H323.
g) Enable use service: Continue pressing
till LCD displays
use service
0[disable]
Vol+
, and then press
to turn over the menu,
Local IP
to enter
change mode. Once a cursor flashes at the beginning of the second line,
please press
that
1
use service
1[enable]
and
Speaker
to enable use service. Then verify
is displayed on LCD.
h) Set service address (take 203.93.9.57 as example): Please continue
pressing
Vol+
to turn over the menu, till LCD displays
Beijing Centrality Communications Co., Ltd
service address
,
14
Centrality PA168 Series IP Phone PPPoE Configuration Guide
and then press
Local IP
to enter change mode. Once a cursor
flashes at the beginning of the second line, press 203*93*9*57 keys in
order to set the GK IP; then click
that
service address
Speaker
to confirm. Please verify
is displayed on LCD.
203.93.9.57
i) Set service port (take 1719 as example): pressing
over the menu backward, till LCD displays
press
to turn
Vol-
service port
; and then
to enter change mode. Once a cursor flashes at the
Local IP
beginning of the second line, press 1719 keys in order to set service
port; then press
service port
to confirm. Verify that
Speaker
1719
is
displayed on LCD.
j) Enter phone setting sub menu: press
setting menu; once
protocol
settings
Redial
key to exit protocol
is displayed again, press
over to phone setting menu
phone
settings
Vol+
, then press
to turn
Speaker
to
enter it.
k) Enable multi-settings: Once you enter protocol setting menu, continue
pressing
Vol+
to turn over the menu, till
on LCD; and then press
Local IP
use inner line
0[disable]
is displayed
to enter change mode. Once a cursor
flashes at the beginning of the second line, press
enable multi-settings. Please verify that
2
use inner line
2[switch]
and
Speaker
to
is displayed.
l) Set value switching to backup setting 1 (take 56 as example): Please
Beijing Centrality Communications Co., Ltd
15
Centrality PA168 Series IP Phone PPPoE Configuration Guide
press
to turn over the menu, till
Vol+
and then press
Local IP
local prefix
is displayed on LCD,
to enter change mode. Once a cursor flashes
at the beginning of the second line, press 56 keys to set the value, and
then press
Speaker
to confirm. Verify that
local prefix
is displayed.
m) Refer to step l) to set the value switching to backup setting 2 (take 57 as
example).
n) Exit and save settings: Continue pressing
menu, until the LCD displays
save settings. When
press
Speaker
save
settings
save
Are you sure?
Redial
to reach save setting
, please press
Speaker
to
is displayed on the LCD, please
again to confirm.
6.4. Set backup setting: to allow the phone switch between different settings,
please do as follows:
1) Write setting files: After the above setting is saved into the phone as
current setting, please write the backup settings in txt format according
to your requirement. For example: with H323 protocol used, backup
setting 1 sets the phone call other IP phone log in the gatekeeper
203.93.9.57; while backup setting 2 sets the phone to call PSTN phone
by eTalk card. Refer to following settings please:
[SETTING1]
service=1
Beijing Centrality Communications Co., Ltd
16
Centrality PA168 Series IP Phone PPPoE Configuration Guide
serviceport=1719
proxy=2
serviceaddr=203.93.9.57
dialplan=0
prepaid=0
[SETTING2]
service=1
serviceport=1719
proxy=0
serviceaddr=202.91.230.91
dialplan=2
dialnumber=00
innerline=0
serviceid=ETNSGK
prepaid=2
account=0117ETNS
pin=586095682629
Note Parameters here are same with the telnet command. Letters in “[]”should be
capital.
b) Update files: In PalmTool index page, input the IP address of the phone
into the ip address in chip, and then click update alternate button, then
please select the saved setting files (such as setting.txt) in following
window to update.
After updating, the backup settings cannot be seen in PalmTool. To check and
change the backup setting, please use load, store and set command in Telnet.
For example, change the dial rule in backup setting 3, please do as follows:
Enter Telnet command window firstly: on the PC connecting with the phone,
click Start>Run, and then input telnet 192.168.1.100 into the Run dialog.
Refers to following images please:
Beijing Centrality Communications Co., Ltd
17
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Fig6.4 Select Start>Run
Fig6.5 Input Telnet command
In Telnet window, load backup setting 3 to the current position by using load
and then check the setting with get command as follows:
PA168S V1.31 settings
Password: ********Å Input password
P:\>load 3
Å Load backup setting 3 to current position
P:\>get
Å Check current setting
iptype 0[static]
ip 192.168.1.100
subnetmask 255.255.255.0 router 192.168.1.254
dns 202.106.196.152
dns2 202.106.196.115
mac 00-09-45-65-a3-e6
protocol 0[h323]
proxy 2[citron]
Then you can change the setting with set command as follows:
upgradeaddr [empty]
ntsip 210.59.157.10
daylight 0[disable]
timezone 20[(GMT-03:00)Greenland]
P:\>set dialplan 1
Å Enable dial rule
P:\>set iddcode 86 Å Set country code
P:\>set iddprefix 00 Å Set country code prefix
P:\>set dddprefix 0 Å Set long distance code prefix
P:\>set dddcode 10 Å Set long distance code
P:\>store 3
Å Save current setting to backup setting 3
P:\>write Å Confirm change
7. Connect the IP phone into the Internet as follows:
Beijing Centrality Communications Co., Ltd
18
Centrality PA168 Series IP Phone PPPoE Configuration Guide
7.1. Disconnect the IP phone and PC: Turn off the phone and then pull out the
cross cable from PC. Refer to Fig 7.1 please.
Cross cable
Fig 7.1 Disconnect the IP Phone and PC
7.2. Connect the Phone to Internet: Insert the end pulled out from the PC into
the RJ-45 cord port of the ADSL Modem or Cable Modem. Refer to Fig
12.2 please. Then turn on the IP phone.
ADSL Modem or Cable Modem
Cross cable
Fig 7.2 Connect the Phone to Internet
8. Communication: With successful PPPoE dial-up, ISP automatically
assigns IP address, subnet mask and router IP to the phone. And then the
phone will log in the procotol. Verify that No. 19 light blinks and then is off.
Then you can use the phone to communicate with other party as follows:
8.1. Place the calls:
1) Call other IP phones log in the same server as follows:
Pick up the handset or press
Beijing Centrality Communications Co., Ltd
Speaker
, and then use the keypad
19
Centrality PA168 Series IP Phone PPPoE Configuration Guide
to enter the phone number of the other IP phone, such as
87452356. Then press
or
#
to confirm. Once the call
Call
connection has been established and the ring tone has sounded,
wait for the other party to answer. When the other party answers,
you can begin speaking. When the call is over, put back the
handset or press
Speaker
again. The dialed number has been
saved into the last calls made buffer.
2) With multi-settings being enabled, for example, current setting is
calling other IP phone log in GK (203.93.9.57); while backup
setting 1 is calling ordinary phone by eTalk card, do as follows:
① Call other IP phone log in the same GK:
Pick up the handset or press
Speaker
, and then use the
keypad to enter the phone number of the other IP phone, such
as 87452356. Then press
#
or
Call
to confirm. Once the
call connection has been established and the ring tone has
sounded, wait for the other party to answer. When the other
party answers, you can begin speaking. When the call is over,
put back the handset or press
Speaker
again.
② Call ordinary phone by eTalk card:
Pick up the handset or press
Speaker
, and then switch to
backup setting 1 by pressing the designated nonlocal prefix code,
such as
9
. Once you hear the eTalk card balance prompt,
Beijing Centrality Communications Co., Ltd
20
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Please dial the complete number of the other party, such as
00861082378008, and then press
or
#
Call
to confirm.
Once the call connection has been established, you will hear a number
prompting the allowed speaking time. For example, 240, it means that
you can communicate with the other party for 240 minutes.
When the ring tone has sounded, wait for the other party to answer.
When the other party answers, you can begin speaking. When the call
is over, put back the handset or press
Speaker
again.
8.2. Receive the calls: When the phone rings, you can receive the call by
following methods:
1) Use handset: Pick up the handset and begin speaking. When the
call is over, put the handset back.
2) Handset to hand free: While receiving call with handset, press
i.
Speaker
on the keypad and then put down the handset. When
the call is over, press
3) Hand free: Press
call is over, press
Speaker
Speaker
Speaker
again.
to speak to the other party. When the
again.
4) Hand free to handset: While receiving the call with the
Speaker
Pressed, pick up the handset to continue the call. When the call
is over, put back the handset.
Note To assure the quality of speaking; do not be far way from the speaker. The
limitation is 40 CM.
Beijing Centrality Communications Co., Ltd
21
Centrality PA168 Series IP Phone PPPoE Configuration Guide
8.3. Review the calls:
1) Review the received calls: please press
Play
with the phone
turned on. Then you will hear the voice prompt of the latest
received number. To turn over the record backward or forward,
please press
call
the
or
Vol+
current
. During the reviewing, you can
Vol-
nubmer.
For
“No.2 ,87452356”, you can press
example,
##
when
you
hear
.Then the phone will call
87452356 without picking up the handset.
2) Review the missed calls: please press
Record
with the phone
turned on. Then you will hear the voice prompt of the latest missed
calls. To turn over the record backward or forward, please press
Vol+
or
Vol-
. During the reviewing, you can call the current
number. For example, when you hear “No.2 ,87452356”, you can
press
#
.Then the phone will call 87452356 without picking
up the handset.
3) Review the made calls: please press
Delete
with the phone
turned on. Then you will hear the voice prompt of the latest calls
made. You can press
Vol+
or
Vol-
to turn over the record
backward or forward. During the reviewing, you can call the
current number. For example, when you hear “No.2 ,87452356”,
you can press
#
.Then the phone will call 87452356 without
picking up the handset.
Beijing Centrality Communications Co., Ltd
22
Centrality PA168 Series IP Phone PPPoE Configuration Guide
Centrality Communications CO., Ltd reserves the right to make changes in
technical and product specification without prior notice.
Centrality PA168X IP Phone PPPoE Configuration Guide
Copyright© 2003, 2004 Beijing Centrality Communications Co., Ltd
All rights reserved
Beijing Centrality Communications Co., Ltd
23