Quadra-Fire QFI35-C Owner`s manual

R
Owner’s Manual
Installation and Operation
Models:
QFI30-C
QFI35-C
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
A CO detector shall be installed in the room where the
appliance in installed.
• Leave this manual with
party responsible for use
and operation.
D
DISO NO
CA T
RD
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Quadra-Fire gas fireplace,
an elegant and clean alternative to wood burning fireplaces.
The Quadra-Fire gas fireplace you have selected is
designed to provide the utmost in safety, reliability, and
efficiency.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Quadra-Fire gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Quadra-Fire family of fireplace products!
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all cautions and
warnings.
Homeowner Reference Information
We recommend that you record the following pertinent
information about your fireplace.
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
R
Type of Gas
Quadra-Fire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX
Gas and Electric
Information
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
Model Number
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
 B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
6
6
6
6
6
User Guide
Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Decorative Fronts and Surrounds . . . . . . . . . . . . . . . . . . . 8
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Controls, Wall Controls and Wall Switches . . . . . . 8
IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . . 8
Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 10
After Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 11
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 12
B. Maintenance Tasks-Service Technician . . . . . . . . . . . . . . 13
Installer Guide
4 Getting Started
A.
B.
C.
D.
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
8 Installing Vent Pipe and Appliance
A.
B.
C.
D.
E.
F.
Vent Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Venting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Vent Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing, Securing and Leveling the Appliance . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Adaptor and Termination Cap . . . . . . . . . . . . . .
22
22
22
23
24
25
9 Gas Information
2 Operating Instructions
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
C. Gas Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
D. Fireplace Conversion Notice . . . . . . . . . . . . . . . . . . . . . . 21
E. Electrical Outlet Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
15
16
16
16
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
26
26
10 Electrical Information
A.
B.
C.
D.
E.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IntelliFire™ Plus Ignition System Wiring . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Fan Wiring with Remote . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . .
27
27
28
29
29
11 Finishing
A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 30
12 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
Remove Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Place the Lava Rock . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
31
31
31
31
31
32
38
38
13 Troubleshooting
5 Fireplace Size Requirements
 A. Minimum Fireplace Opening . . . . . . . . . . . . . . . . . . . . . . 17
B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 19
6 Termination Locations
A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 20
7 Installation Preparation
A. Inspection and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 21
B. Flue Damper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
A. IntelliFire™ Plus Ignition System . . . . . . . . . . . . . . . . . . . 39
14 Reference Materials
A.
B.
C.
D.
Appliance/Decorative Front Dimension Diagrams . . . . . .
Vent Kits Components . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41 
44
45 
49
 = Contains updated information.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
3
 B.
Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
X
X
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Ignition Modules
Firepots and burnpots
X
5 years
Components Covered
Electric Venting
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645G 2/15
4
Page 1 of 2
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
 B.
Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645G 2/15
Page 2 of 2
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
5
1
Listing and Code Approvals
A. Appliance Certification
D. High Altitude Installations
LABORATORY: Underwriters Laboratories, Inc. (UL)
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
TYPE: Direct Vent Heater
When installing above 2000 feet elevation:
STANDARD: ANSI Z21.88-2014 CSA 2.33-2014
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
MODELS: QFI30-C, QFI35-C
Vented Gas Fireplace Heaters
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
Quadra-Fire gas inserts are designed for installations into
solid fuel masonry or factory built fireplaces that have been
installed in accordance with the National, Provincial, State
and local building codes. Fireplaces are to be constructed
of non-combustible materials and, in the absence of local
or regional codes, meet criteria of NFPA 211. No additional
outside air source is required.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Glass Specifications
This appliance is equipped with 5 mm ceramic glass. Replace glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
US
(0-2000 FT)
32,000
18,000
#35
CANADA
(2000-4500 FT)
28,800
16,200
#36
US
(0-2000 FT)
35,000
18,500
#33
CANADA
(2000-4500 FT)
33,250
18,250
#34
US
(0-2000 FT)
31,000
15,500
#51
CANADA
(2000-4500 FT)
27,500
14,500
#52
US
(0-2000 FT)
35,000
17,000
#50
CANADA
(2000-4500 FT)
31,000
15,500
#51
Models
(U.S. or Canada)
QFI30-C (NG)
QFI35-C (NG)
QFI30-C (LP)
QFI35-C (LP)
6
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
2
Operating Instructions
User Guide
A. Gas Fireplace Safety
• Teach children to NEVER touch the fireplace.
WARNING! DO NOT operate fireplace before reading
and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
• Consider not using the fireplace when children will be
present.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacation/trips, etc):
• Remove batteries from remote controls.
• Turn off wall controls.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• Keep children away.
• CAREFULLY SUPERVISE children in same room
as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Clothing, furniture, draperies, and other flammable
materials must not be placed on or near the
appliance.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals. DO NOT operate the appliance with
the barrier removed. If the barrier becomes damaged,
the barrier shall be replaced with the manufacturer’s
barrier for this appliance.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
B. Your Fireplace
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
APPLIANCE INSTALLED IN EXISTING
SOLID FUEL FIREPLACE
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.D.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 12.H.
Young children should be carefully supervised when they
are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns.
HEARTH
CLEAR SPACE
SECTION 2.C.
• A physical barrier is recommended if there are at risk
individuals in the house.
• To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away
from hot surfaces.
MANTEL
SECTION
5.B AND
11.A
Figure 2.1 General Operating Parts
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
7
C. Clear Space
E. Fixed Glass Assembly
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
See Section 12.H.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
F. Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
APPLIANCE INSTALLED IN EXISTING
SOLID FUEL FIREPLACE
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
G. IPI Battery Tray/Battery Installation
The IntelliFireTM Plus system has a battery backup option.
Battery longevity and performance will be affected by the
service temperatures of this appliance. Batteries should only
be used as a power source in the event of an emergency
such as an outage.
3F
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
LA
CE
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage.
Figure 2.2 Clear Space
D. Decorative Fronts and Surrounds
WARNING! Risk of Fire! Install ONLY decorative fronts
or surrounds approved by Hearth & Home Technologies.
Unapproved decorative fronts may cause appliance to
overheat.
This appliance has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the appliance with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative front.
8
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
H. Control Module Operation
5. Module Reset
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respond to commands. The module will go into lock-out
mode by emitting three audible beeps, then continuously
displaying a RED/GREEN error code at its status
indicator LED.
1. The control module has an ON/OFF/REMOTE selector
switch that must be set. See Figure 2.3.
OFF Position: Appliance will ignore all power inputs and
will not respond to any commands from a wall switch or
remote. The unit should be in the OFF position during
installation, service, battery installation, fuel conversion,
and in the event that the control goes into LOCK-OUT
mode as a result of an error code.
ON Position: Appliance will ignite and run continuously
in the HI flame setting, with no adjustment in flame
output. This mode of operation is primarily used for
initial installation or power outage operation with battery
backup.
REMOTE Position: Appliance will initiate commands
from an optional wired wall switch and/or the wireless
remote (RC300).
2. If using a wired wall switch with the module in REMOTE
mode, the flame output can be adjusted with the HI/LO
selector switch on the module. See Figure 2.3. Note
that the flame HI/LO selector switch will become inactive
once an optional remote control (RC200/RC300) is
programmed to the control module. Note that the control
module will always ignite the fireplace on HI and remain
so for the initial 10 seconds of operation. If the HI/LO
is switched to the LO position, the flame output will
automatically drop to the lowest setting after the flame
has been established for 10 sec. After this 10 second
period, the flame can be adjusted from HI to LO with
the switch.
•
Check battery tray. Remove batteries if installed.
Batteries should only be installed for use during power
outages. See Section G.
•
Locate the module selector switch. (See Figure 2.3).
•
Set the module selector switch to the OFF position.
•
Wait five (5) minutes to allow possible accumulated gas
to clear.
•
Set the module selector switch to ON or REMOTE
position.
•
Start the appliance.
WARNING! Risk of Explosion! DO NOT reset the module more than one time within a five minute time period.
Gas may accumulate in firebox. Call a qualified service
technician.
Nine Hour Safety Shutdown Feature
The appliance has a safety feature that automatically
shuts down the fireplace after nine hours of continuous
operation without receiving a command from the wall
switch or optional remote.
3. The control module has safety feature that automatically
shuts down the fireplace after 9 hours of continuous
operation without receiving a command from the RC300
remote.
I. Before Lighting Fireplace
4. If you intend to use both an optional wired wall switch
and the RC300 remote control to operate your fireplace,
the wall switch will override any commands given by
the remote.
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
MODULE
Before operating this fireplace for the first time, have a
qualified technician:
• Review proper placement of logs, ember material and/
or other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
SELECTOR
SWITCH
WARNING! Risk of Fire/Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
• An Intellifire™ Plus ignition system is standard with this
appliance.
FLAME HI/LOW
SWITCH
STATUS
INDICATOR LED
NG/LP GAS-TYPE
SELECTOR SWITCH
Figure 2.3 Control Module
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
9
J. Lighting Instructions (IPI)
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an intermittent pilot ignition (IPI) device which
automatically lights the burner. DO NOT try to light the burner by hand.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell
next to the floor because some gas is heavier than air and will settle on the floor.
• If you cannot reach your gas supplier, call the fire department.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If
the knob will not push in or turn by hand, DO NOT try to repair it, call a qualified
service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part of
the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS (IPI)
1.
This appliance is equipped with an ignition device which
automatically lights the burner. DO NOT try to light the burner by hand.
GAS
VALVE
2.
Wait five (5) minutes to clear out any gas. Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the
top of this label. If you do not smell gas, go to next step.
3.
To light the burner:
Equipped with wall switch: Turn ON/OFF switch to ON.
Equipped with remote or wall control: Press ON or FLAME button.
Equipped with thermostat: Set temperature to desired setting.
4.
If the appliance does not light after three tries, call your service technician or gas
supplier.
TO TURN OFF GAS TO APPLIANCE
1.
Equipped with wall switch: Turn ON/OFF switch to OFF.
Equipped with remote or wall control: Press OFF button.
Equipped with thermostat: Set temperature to lowest setting.
2.
Service technician should turn off electric power to the control when performing
service.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
WARNING:
CAUTION:
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner’s information manual provided with
this appliance. For assistance or additional information, consult a qualified installer,
service agency or the gas supplier.
DO NOT operate the appliance with fixed glass assembly removed, cracked or
broken. Replacement of the fixed glass assembly should be done by a licensed or
qualified service person.
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.
This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which
are known to the State of California to cause cancer, birth defects, or other reproductive
harm.
Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline
and other liquids having flammable vapors away.
NOT FOR USE WITH SOLID FUEL
For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.
Also Certified for Installation in a Bedroom or a Bedsitting Room.
This appliance must be installed in accordance with local codes, if any; if none,
follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and
Propane Installation code, CSA B149.1.
Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
10
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
593-913i
K. After Appliance is Lit
Initial Break-in Procedure
• The appliance should be run three to four hours
continuously on high.
• Turn the appliance off and allow it to completely cool.
• Remove fixed glass assembly. See Section 12.H.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 9 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during appliance break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
L. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn
continually?
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
11
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the appliance.
Surrounds, Decorative Fronts
Frequency: Annually
When properly maintained, your appliance will give you
many years of trouble-free service. We recommend annual service by a qualified technician.
By: Homeowner
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified technician only. The appliance should be inspected before use
and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the appliance must be
kept clean.
CAUTION! Risk of Burns! The appliance should be
turned off and cooled before servicing.
Glass Cleaning
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Check that louvers are not blocked.
• Vacuum or dust surfaces.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
Frequency: Seasonally
• Place batteries as needed in remote transmitters and
battery-powered receivers.
By: Homeowner
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Remove batteries from remote controls.
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
• Remove decorative front from appliance and set aside
on work surface.
• See Section 12.H for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on appliance.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall decorative front.
12
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
Venting
Control Compartment and Firebox Top
Frequency: Seasonally
Frequency: Annually
By: Homeowner
By: Service Technician
Tools needed: Protective gloves and safety glasses.
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Inspect for corrosion or separation.
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
B. Maintenance Tasks-Service Technician
The following tasks must be performed by a qualified
technician.
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
Logs
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as necessary.
Refer to Section 12 for log placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
Firebox
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace appliance if firebox has been perforated.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
13
Burner Ignition and Operation
Frequency: Annually
By: Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 12 for proper ember placement.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or
leaking. For optimal battery life, locate the battery
pack outside of the control cavity on the hearth. This
placement will reduce the chances of overheating the
batteries during extended burns which could result in
reduced battery life or degradation.
Figure 3.1 IPI Pilot Flame Patterns
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
• Verify air shutter setting is correct. See Section 12 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect thermocouple/thermopile or IPI flame sensing
rod for soot, corrosion and deterioration. Polish with fine
steel wool or replace as required.
• Verify that there is not a short in flame sense circuit by
checking continuity between pilot hood and flame sense
rod. Replace pilot as necessary. (IPI only)
14
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
4
Installer Guide
Getting Started
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
VERTICAL TERMINATION CAP
(SECTION 8.F)
VENT PIPE
(SECTION 8)
3 INCH FLEX LINERS
(SECTION 8)
MANTEL AND MANTEL LEG
SECTION 5.B AND 11.A
SURROUND OR FRONT
NOT SHOWN
SECTION 2.D AND 8.D.
HEARTH EXTENSION
GAS LINE (SECTION 9)
ACCESS THROUGH EXISTING
MASONRY OR WOODBURNING
FIREPLACE
Figure 4.1 Typical System
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
15
B. Design and Installation Considerations
C. Tools and Supplies Needed
Quadra-Fire gas inserts are designed for installations into
solid fuel masonry or factory built fireplaces that have
been installed in accordance with the National, Provincial, State and local building codes. Fireplaces are to be
constructed of non-combustible materials and, in the absence of local or regional codes, meet criteria of NFPA
211. No additional outside air source is required.
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Flat blade screwdriver
Hammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Noncorrosive leak check solution
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local
building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.
Prior to installing the gas insert:
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
• Ensure combustible mantel and surround clearances
comply with applicable codes and regulations for solidfuel fireplaces. In the absence of local or regional codes,
refer to NFPA 211.
• Ensure all joints are properly engaged and the chimney
is properly secured.
• Minimum fireplace size. See Section 5.A.
D. Inspect Appliance and Components
• Carefully remove the appliance and components from
the packaging.
• The vent system components and decorative fronts may
be shipped in separate packages.
• If packaged separately, the log set and appliance grate
must be installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Gas supply piping requirements.
• Electrical wiring requirements.
• Finishing details.
• Whether optional accessories—devices such as a wall
switch or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
technician, service agency or your dealer.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory
trained professionals, or technicians supervised
by an NFI certified professional.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire,/Explosion/Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified technician to inspect the appliance
and to replace any part of the control system and/or gas
control which has been under water.
16
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
5
Fireplace Size Requirements
A. Minimum Fireplace Opening
• The metal floor of the solid fuel firebox may be removed
to facilitate the installation of the insert.
Minimum fireplace opening requirements for a standard 3/4
inch deep surround are shown in Figure 5.2. For smaller
openings, an optional 1-1/2 inch deep surround is available
and dimensions are shown in Figure 5.3.
• Cutting of any sheet metal parts of the fireplace in which
the gas fireplace insert is to be installed is prohibited,
except the floor as tested for and as noted above and in
Figure 5.1.
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• A minimum 1/2 inch gap from the bottom of the
appliance to the metal floor of the solid fuel firebox is
RECOMMENDED for optimal fan performance. See
side view in Figure 5.1
• The firebrick (refractory), glass doors, screen rails, screen
mesh and log grates can be removed from a factory
built firebox in order to gain minimum gas insert opening
requirements.
• Any smoke shelves, shields and baffles may be removed
from the factory built firebox if attached with mechanical
fasteners.
TOP VIEW
SIDE VIEW
METAL FLOOR OF EXISTING
SOLID FUEL FIREBOX
9 IN.
5 IN.
3 IN.
6 IN.
REMOVE THIS
SECTION OF
METAL FLOOR
1/2 IN. MINIMUM LEVELING HEIGHT
(RECOMMENDED)
1/4 IN. REQUIRED
FACTORY BUILT FIREBOX
METAL FLOOR OF EXISTING SOLID FUEL FIREBOX
9 IN.
METAL INSERT
5 IN.
3 IN.
REMOVE THIS
SECTION OF
METAL FLOOR
Figure 5.1-A
6 IN.
Figure 5.1-B
• The appliance may not be placed directly on the base of
the outer wrap, a 1/4 inch airspace MUST be provided
between the insert and the floor of the outer wrap. Use
the leveling legs to raise the insert a minimum of 1/4 inch.
The original fireplace may never be returned to solid
fuel in this condition. The sidewalls and top structure
of the firebox may not be altered with the exception of
removable baffles and dampers.
• If a minimum 1/2 inch gap can not be achieved, a section
of the factory-built metal floor can be removed. See
Figure 5.1-B.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
17
FRONT VIEW
TOP VIEW
SIDE VIEW
C
A
E
D
I
F
G
H
B
MINIMUM FIREPLACE SIZE
QFI35-C
QFI30-C
Location
Inches
Millimeters
Inches
Millimeters
A
Rear Width
23-7/16
595
20-3/16
513
B
Front Width
34-5/8
879
30-5/8
778
C
Glass Opening Width
31-5/8
803
27-1/2
699
D
Glass Opening Height
15-11/16
398
12-3/16
310
E
Height-Front
24-1/16
611
20-7/16
519
F
Height-Rear
21-1/8
537
17-5/8
448
Unit Depth
15-3/4
400
14-3/4
375
H
Venting Depth
10-5/8
270
9-1/2
241
I
Height to Top of
Glass Frame
21-5/8
549
18-1/4
464
G**
* Note: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102 mm) to minimum
fireplace height for bends in vent pipe.
**Unit depth is measured to the back of the surround to give the depth needed for installation.
In addition to these dimensions, also reference Clearances and Mantel Projections (Section 5.B).

Figure 5.2 Fireplace Opening
18
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
SIDE VIEW
TOP VIEW
1-1/2 IN.
BD
AD
CD
SURROUND
SURROUND
APPLIANCE
APPLIANCE
MINIMUM FIREPLACE SIZE
QFI35-C
QFI30-C
Location
Inches
Millimeters
Inches
Millimeters
AD
Alternate Unit Width
33-3/16
843
29-1/16
738
BD
Alternate Unit Depth
15-1/16
383
13-7/8
352
CD
Alternate Unit Height
22-9/16
573
19-1/16
484
* Note: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102 mm) to minimum
fireplace height for bends in vent pipe.
Figure 5.3 Fireplace Opening - Deep Surround
B. Mantel and Wall Projections
EXISTING NON-COMBUSTIBLE FACING
WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
12 IN. MAX.
Clearance to combustible material under the insert is 1/4
inch (6 mm). Clearance from top of fireplace opening for
combustibles extending 12 inches max. is 12 inches.
• Use leveling legs to raise insert minimum 1/4 inch (6 mm)
above combustible material or outer wrap of factory built
firebox.
Combustible facings must not extend behind the insert
surround. For non-combustible material specifications
refer to section 1.E.
2 IN.
MAX.
12 IN. MIN.
10 IN. MIN.
Figure 5.4 Mantel Clearances
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
19
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or
other materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5*
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
20
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
7
Installation Preparation
Prepare the existing solid fuel masonry or factory built
non-combustible firebox for installation.
A. Inspection and Cleaning
Prior to installing the gas insert:
D. Fireplace Conversion Notice
Permanently attach the label with the following warning to
the inside lower back of the fireplace firebox into which the
insert is being installed. Silicone or mechanical fasteners
may be required to properly secure the label.
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified
professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney.
WARNING! Risk of Fire! This fireplace has been converted for use with a gas fireplace insert only and cannot
be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved
by the authority having jurisdiction.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
E. Electrical Outlet Box
• Ensure all joints are properly engaged and the chimney
is properly secured.
• Ensure combustible mantel and surround clearances
comply with applicable codes and regulations for solidfuel fireplaces. In the absence of local or regional codes,
refer to NFPA 211.
An outlet box may be installed in a bottom back corner of
the existing solid fuel masonry or factory built fireplace to
power the appliance. Each unit ships standard with a cord
assembly to permit blowers or other optional accessories
to be used. The accessories plug into the new outlet box
or may be routed out onto the hearth to a nearby outlet.
• Ensure chimney is constructed of non-combustible
materials.
• Ensure chimney is clean and in good working order.
• Ensure that all chimney cleanouts fit properly to prevent
air leakage into chimney.
B. Flue Damper
Fully lock the solid fuel fireplace’s flue damper in the open
position, OR completely remove it.
C. Gas Line
Note: If the factory built fireplace has no gas access hole
provided, an access hole of 1 inch (25 mm) diameter or
less may be drilled through the lower sides or bottom of the
firebox in a proper workmanship - like manner. This access
hole must be plugged with non-combustible insulation after
the gas supply line has been installed.
• Install gas line into firebox cavity.
• Check local codes and gas line sizing requirements
following NFPA51. See Section 9.
• It is recommended that extra length of gas line be
installed within the existing wood burner or masonry
fireplace to allow removal of the insert for future servicing
needs.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
21
8
Installing Vent Pipe and Appliance
A. Vent Limits
B. Venting Components
The abbreviations listed in this vent table key are used in
the vent diagrams.
CAUTION! Risk of Cuts/Abrasions/Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
Description
Minimum Vertical Run Length 10 ft.
The vertical vent termination system installed on this model
includes:
Maximum Vertical Run Length 50 ft.
• Flexible vent pipe for exhaust air (included with vent kit).
Horizontal venting is NOT allowed.
Vertical terminations are measured to top of chimney.
This appliance is listed for use with LINK-DV systems
and components only. It is permissible to extend venting
above existing chimney (within specified maximum vertical limits) using SL-D series or Dura Vent GS series 4 in.
x 6-5/8 in. gas direct-vent pipe. Connection is made using DV-46DVA-GK. The vent must be terminated with the
cap supplied with the LINK-series vent kit.
WARNING! Risk of Fire/Explosion/Asphyxiation! Do
NOT connect this gas appliance to a chimney flue serving
a separate solid fuel or gas burning appliance.
• May impair safe operation of this appliance or other
appliances connected to the flue.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
CAUTION! ALL vent specifications MUST be followed.
This product is tested and listed to these specifications.
Appliance performance will suffer if specifications are not
followed.
• One length of 3-inch flexible vent pipe for combustion
air (included with vent kit).
• One pipe-to-cap adaptor (included with vent kit).
• One vertical termination cap (included with vent kit).
C. Connecting Vent Pipe
Reference instructions in the termination kit.
• Install the 3-inch flexible vent pipe(s) down through the
chimney.
• Secure the exhaust flexible vent pipe to the exhaust
starting collar on top of the appliance with three screws.
See Figure 8.1.
• Use 3 screws to attach the section of inlet air vent to
the inlet collar on the collar slide plate. See Figure 8.1.
NOTE: The collar slide plate may be removed from
appliance to aid installation.
TERMINATION
CAP
ADAPTER
INLET
COLLAR
EXHAUST
COLLAR
INLET AIR STARTING COLLAR
V = 10 FT. MINIMUM
50 FT. MAXIMUM
EXHAUST
AIR
VENT PIPE
LOCKING TAB
STARTING COLLAR BRACKET
HANDLE
EXHAUST STARTING COLLAR
INLET AIR
VENT PIPE
INLET AIR STARTING COLLAR
STARTING COLLAR BRACKET
NOTE: TO ACHIEVE OPTIMUM PERFORMANCE OF INSERT, MINIMIZE OR AVOID
BENDS IN EXHAUST VENT PIPE.
EXHAUST STARTING COLLAR
Figure 8.1
22
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
CUT AND BEND
FLASHING AS NEEDED
TO FIT CHIMNEY
SEALANT
ADHESIVE
• Attach surround. Follow instructions for surround
installation included with the front.
• Push insert into the opening so that it tightly overlaps the
fireplace opening.
WARNING! Risk of Fire! Only an approved Hearth &
Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces. No other components such as shrouds, sheetmetal plates, etc., may be
used to seal off vents.
WARNING! Risk of Explosion! Failure to position the
parts in accordance with these diagrams or failure to use
only parts specifically approved with this appliance may
result in property damage or personal injury.
Figure 8.2
• Trim chimney top plate to minimize excess overhang or
bend over flue tile (see Figure 8.2).
REAR LEVELING LEGS
SHIPPED IN THIS POSITION
• Place 3/8 inch bead of 300ºF silicone on flue tile top.
D. Placing, Securing and Leveling the
Appliance
WARNING! Risk of Explosion/Combustion Fumes!
Connect vent sections per installation instructions.
• Connect exhaust vent pipe ONLY to exhaust starting
collar and termination cap center collar.
• Connect inlet air vent ONLY to inlet air collar on appliance
and the termination cap inlet air collar.
• DO NOT allow vent to sag below connection point to
appliance.
REAR LEVELING LEGS MAY BE RELOCATED
TO LOCATION A OR LOCATION B
• Remove rear leveling legs from shipping position and
relocate to one of the positions shown in Figure 8.3.
Remove both screws that secure the leveling leg to the
side of the appliance. Turn the leveling leg around so
that the foot is facing out and downward. Line up the
two holes on the leg with the holes on the appliance and
secure with screws. See Figure 8.3.
LOCATION A
• Install insert (without surround attached) into existing
fireplace while pulling collar slide plate forward.
• Install gas line into hole provided on side.
• If applicable install remote control wires into insert side
See Section 8.E.
• Secure collar slide plate to appliance by placing locking
handle into position with locking tabs (see Figure 8.1)
and secure with #8 screw.
LOCATION B
• Level the appliance from side to side and front to back.
Adjust leveling bolts to desired vertical position so
appliance is level. Use the leveling bolts included with
the manual bag.
• A minimum 1/2 inch gap from the bottom of the appliance
to a metal surface is RECOMMENDED for optimal fan
performance. See Figure 5.1.
• Position any excess flexible vent pipe back up into
chimney without sagging. Twist and push flex vent
together to shorten.
Figure 8.3
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
23
E. Remote Control
IPI Models:
If a remote control kit is used to control blower function,
the Auxiliary 300 module can only be placed in the control
cavity to the right of the control panel. See Figure 8.4.
AUXILIARY 300 MODULE
Figure 8.4 Location of AUX300 for Remote Control
Blower Function - IPI
24
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
F. Installing Adaptor and Termination Cap
For installation of termination cap see minimum vent
heights for various pitched roofs (see Figure 8.5) .
CAUTION! Risk of Cuts/Abrasions/Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
To install adaptor see Figure 8.6.
Damper Flashing Kit (Optional)
For use with LINK-DV30B, LINKSQ-DV30, LINK-DV430B or LINKSQ-DV4-30 Liner Kit.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Note: Damper may have to be removed to use this kit.
• Run flex liners through 3 in. holes in damper flashing.
VERTICAL
WALL
• Attach damper flashing to firebox roof with self tapping
screws included in kit.
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
CLASS A PIPE
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Over 11/12 to 12/12 ....... 4.0
Over 12/12 to 14/12 ....... 5.0
Over 14/12 to 16/12 ....... 6.0
Over 16/12 to 18/12 ....... 7.0
Over 18/12 to 20/12 ....... 7.5
Over 20/12 to 21/12 ....... 8.0
Roof Pitch
H (Min.) Ft.
Flat to 6/12....................1.0*
Over 6/12 to 7/12 ........1.25*
Over 7/12 to 8/12 ..........1.5*
Over 8/12 to 9/12 ..........2.0*
Over 9/12 to 10/12 ........2.5*
Over 10/12 to 11/12 ..... 3.25
* 3 foot minimum in snow regions
Figure 8.5 Minimum Height from Roof to Lowest Discharge
Opening
Figure 8.6
To prevent odors and cold drafts, the chimney must be sealed around the vent
with non-combustible blanket insulation or field fabricated metal plates.
Masonry
LINK-DV30B
LINKSQ-DV30
Installation
Factory Built
Wood Burning
LINK-DV4-30B
LINKSQ-DV4-30
Installation
OPTIONAL LINK-ZC-ADPB
FOR USE WITH CLASS A
WOODBURNING PIPE
TERMINATION
CAP
EXHAUST
AIR
VENT PIPE
Note: The LINK-DV4-30B and LINKSQ-DV4-30
systems REQUIRE this insulation.
EXHAUST
AIR
VENT PIPE
OR
WARNING:
DO NOT BLOCK
THIS PIPE END!
Note: Untwist the
pipe while extending it, to achieve full
30’ length.
INLET AIR
VENT PIPE
Figure 8.7
INLET AIR
VENT PIPE
Remove 18 inch x 18 inch flashing on cap by removing 3
screws. Connect both the LINK-ZC-ADPB to Class A Pipe
and the termination cap to the LINK-ZC-ADPB with the
self tapping screws provided.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
25
9
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 14 for location of gas line
access in appliance.
• Conversions must be made by a qualified technician
(NFI certified or factory-trained) using Hearth & Home
Technologies specified and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Gas Pressure
• The gap between supply piping and gas access hole may
be caulked with caulk with a minimum of 300ºF continuous
exposure rating or stuffed with non-combustible, unfaced
insulation to prevent cold air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire/Explosion! Support control
when attaching pipe to prevent bending gas line.
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Maximum inlet pressure
10.0 in. w.c.
13.0 in. w.c.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire/Explosion! Gas build-up during
line purge could ignite.
WARNING! Risk of Fire/Explosion! High pressure will
damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 inch (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 inch
(13 mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
26
• Purge should be performed by technician certified by
NFI or factory-trained.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In the CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
10
Electrical Information
A. Wiring Requirements
B. IntelliFire™ Plus Ignition System Wiring
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• This appliance comes standard with a 120 VAC cord
assembly which has a female plug in to accommodate
all control options and accessories. See Figure 10.2.
This is required for proper operation of the appliance
(IntelliFire™ Plus Ignition). An outlet box may be installed
in a bottom back corner of the existing solid fuel masonry
or factory built fireplace to plug in the cord assembly,
or the supplied power cord may be routed out onto the
hearth to a nearby outlet.
• A 120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
• Low voltage and 120 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
120V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.
• Wire an outlet box (120VAC) in the bottom back corner of
the existing solid fuel masonry or factory built fireplace to
plug in the cord assembly. The supplied cord assembly
may also be routed out onto the hearth to a nearby outlet.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figure 10.1, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire™ Plus
control valve which operates on a 6 volt/1.5 AMP system.
• Plug the 6 volt transformer plug into the cord assembly
to supply power to the unit OR install 4 AA cell batteries
(not included) into the battery pack before use.
ON/OFF Switch
• An ON/OFF switch is included with the appliance
surround and should be attached to surround/facing.
(See Installation instructions for remote control/fronts).
• If desired an additional wall switch or thermostat may
be added to system as shown in Figure 10.1.
• An Intellifire™ Plus Ignition System is standard with this
appliance.
INTERMITTENT
PILOT IGNITOR
RC100 RC200
RC300
(OPTIONAL WIRELESS REMOTE CONTROLS)
TO CORD ASSEMBLY
120VAC
MODULE
ORG
WHT
FLAME
MODULATION
AUX300 MODULE
FAN
AUX1 AUX2
RED
ORANGE
(PILOT)
GREEN
(MAIN)
RED
BLK
AUX2 NOT USED FOR INSERT MODELS.
PROTECTIVE COVER INCLUDED
TO CORD
ASSEMBLY
(110V)
BATTERY PACK
6V DC
BLK
ROCKER
SWITCH
BROWN
WALL SWITCH
OR REMOTE
INSTALL
EMC FILTER UNIT
GROUND
GROUND
Figure 10.1 IPI Wiring Diagram
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
27
C. Optional Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• To connect optional accessories, the supplied cord assembly should be used. See Figure 10.2 for a wiring
diagram for a blower or remote.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Plug the cord into a convenient outlet.
• An IntelliFire™ Plus Wireless Controls or WSK-21
wired wall switch may be used with the IntelliFire™
Plus Ignition System. Hearth & Home Technologies
recommends that IntelliFire™ Plus wireless controls be
used for their features and functionality with the IntelliFire™ Plus ignition system.
• A standard ON/OFF switch is compatible.
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105° C rated wire. Wire must have high temperature
insulation.
• Must use cord supplied.
PLUG
120V EXISTING
OUTLET
BLOWER
NOTE: IF ANY OF THE ORIGINAL
WIRE AS SUPPLIED WITH THE
APPLIANCE MUST BE REPLACED,
IT MUST BE REPLACED WITH TYPE
1050 C RATED WIRE.
JUMPER WIRE
NOTE: USE ZIP TIES TO RESTRAIN
THE LOOSE WIRES UNDERNEATH
THE APPLIANCE AND KEEP THEM
AWAY FROM THE BLOWER WHEEL
(FAN BLADES).
WHT (2)
GRN (2)
BLK (2)
BLK (2)
GRN (2)
BLK (2)
PLUG INTO 120V
EXISTING OUTLET
TEMPERATURE
SENSOR SWITCH
TO VALVE
ORG
BLK
GRN
BRN
BLK
RED
SPEED CONTROL
(RHEOSTAT)
TO VALVE BRACKET
(GROUND)
DC REGULATOR
RECEPTACLE
VARIABLE SPEED
CONTROL
BLK
BLK
BLK
WHT
BLK
GRN
BLK
TEMPERATURE
SENSOR SWITCH
BLK
FUSE WIRE
ASSEMBLY
BLOWER
RECEPTACLE
BLK
GRN
WHT
Figure 10.2 Fan Wiring Diagram
28
GRN
BLK
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
FUSE WIRE
ASSEMBLY
BLK
GRN
BLK
BLOWERS
D. Fan Wiring with Remote
2. Plug two cord assembly spade connectors together.
This appliance may be used with an RC200 or RC300
remote control. See Figure 10.3.
3. Unplug fan cord assembly from standard cord assembly.
1. Remove cord assembly spades from rheostat and
sensor switch.
NOTICE: Fan speed and operation are controlled by the
remote control. The sensor switch and rheostat are no
longer needed.
5. Plug AUX300 module into the standard cord assembly.
NOTE: IF ANY OF THE ORIGINAL
WIRE AS SUPPLIED WITH THE
APPLIANCE MUST BE REPLACED,
IT MUST BE REPLACED WITH TYPE
1050 C RATED WIRE.
4. Plug fan cord assembly into AUX300 module.
E. Control Module Operation
See Section 2.H for control module operation instructions.
PLUG
120V EXISTING
OUTLET
BLOWER
STEP 5
NOTE: USE ZIP TIES TO RESTRAIN
THE LOOSE WIRES UNDERNEATH
THE APPLIANCE AND KEEP THEM
AWAY FROM THE BLOWER WHEEL
(FAN BLADES).
STEPS
3&4
STEPS
1&2
SENSOR SWITCH
WHT (2)
GRN (2)
BLK (2)
BLK (2)
GRN (2)
BLK (2)
SPEED CONTROL
(RHEOSTAT)
NOTE: SENSOR SWITCH AND
RHEOSTAT SPEED CONTROL MUST
BE REMOVED FROM CIRCUIT IF
SYSTEM IS CONTROLLED WITH
RC200/RC300 REMOTE.
PLUG INTO 120V
EXISTING OUTLET
DC REGULATOR
RECEPTICLE
BLK
AUX 300 MODULE
TO CONTROL
MODULE
BLK
GRN
WHT
GRN
BLK
BLOWERS
FUSE WIRE
ASSEMBLY
FAN
BLK
BLK
BLK
GRN
WHT
BLOWER
RECEPTICLE
FUSE WIRE
ASSEMBLY
BLK
GRN
BLK
Figure 10.3 Wiring Diagram - Fan with RC200/RC300 Remote
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
29
11
Finishing
A. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Framing or finishing
material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
EXISTING NON-COMBUSTIBLE FACING
12 IN. MAX.
Clearance to combustible material under the insert is 1/4
inch (6 mm). Clearance from top of fireplace opening for
combustibles extending 12 inches max. is 12 inches.
• Use leveling legs to raise insert minimum 1/4 inch (6 mm)
above combustible material or outer wrap of factory built
firebox.
Combustible facings must not extend behind the insert
surround. For non-combustible material specifications
refer to section 1.E.
2 IN.
MAX.
12 IN. MIN.
10 IN. MIN.
Figure 11.1 Clearances to Mantels or other Combustibles
above Appliance
30
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
12
Appliance Setup
A. Remove Glass Assembly
F. Ember Placement
See Section 12.H.
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• Place dime-size pieces of Glowing Embers® just in front
of the port trail, but not on or in between the ports (see
Figure 12.2). Care should be taken so that the ports are
not covered. Failure to follow this procedure will likely
cause lighting and sooting problems.
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
E. Place the Lava Rock
WARNING! Risk of Explosion! Follow lava rock placement instructions in manual. DO NOT place lava rock on
burner. Improperly placed lava rock interferes with proper
burner operation.
EMBERS NOT
ALLOWED IN
PILOT AREA
Lava rock is shipped with this gas appliance. To place
the lava rock:
• Lava rock CANNOT be placed on the burner.
• Place lava rock in front of and to the sides of the
burner.
Figure 12.2 Placement of Embers
PLACE LAVA ROCK IN SHADED AREA ONLY
Figure 12.1 Placement of Lava Rock
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
31
G. Install the Log Assembly
Log Set Assembly: LOGS-QFI30
Models: QFI30, QFI30-C
LOG SUPPORT
SRV2227-702
SRV2227-705
SRV2227-703
PILOT
ASSEMBLY
SRV2227-704
LEFT GRATE
TINE
SRV2227-706
LOG PIN
RIGHT GRATE TINE
SRV2227-701
Figure 1. Reference Points for Log Placement
Figure 2. Refractory and Logs Installed
Figure 3. Install Back Refractory
CAUTION: Logs are fragile, handle with care. Install back refractory by placing it against the back of the firebox. See Figure
3. The back refractory must be held in the upright position until the side refractory is installed. Install the left side refractory
as shown in Figure 4. Bend the refractory tab down as shown in Figure 5. Repeat this step for the right refractory panel.
Figure 4. Install Side Refractory
32
Figure 5. Bend Refractory Tab
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
FLAT SPOT FOR LOG #2
FLAT SPOT FOR LOG #5
NOTCH
1
LOG CORNER ALIGNS
WITH LOG TAB
NOTCH MATES WITH LEFT
GRATE TINE
Figure 6. Placement of Log #1
Figure 7. Location of Notch on Log #1
Log #1 (SRV2227-703): Mate the notch located on the bottom of the log, with the left grate tine. See Figure 7. Bend the
tab located to the left of the pilot assembly into the vertical position. Rotate the back end of log clockwise until it contacts
the log tab as shown in Figure 6.
LOG CONTACTS REFRACTORY
LOG GROOVE
(FOR LOG #6)
LOG RESTS ON
REFRACTORY SUPPORT
2
3
LOG CONTACTS
LOG SUPPORT
NOTCH MATES WITH
RIGHT GRATE TINE
LOG RESTS ON BURNER
Figure 8. Place Log #2
Figure 9. Log #3
Log #2 (SRV2227-702): Rest left end of log on the flat spot of Log 1. See Figure 6 and Figure 8. The left end of the log
should touch the left refractory panel. The right end rests on the burner. Push the right end back, until it touches the edge
of the log support.
Log #3 (SRV2227-701): Mate the notch with the right grate tine as shown in Fig 9. The back of the log should rest on the
log support as shown. Rotate the back end of the log clockwise until it contacts the right refractory panel.
LOG PIN
MATES
WITH SLOT
LOG GROOVE
(FOR LOG #6)
4
MATE NOTCH
WITH GRATE BAR
Figure 10. Log #4
NOTCH
Figure 11. Log #4
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
33
Log #4 (SRV2227-705): Mate the slot on the bottom of the log, shown in Figure 12, with the log pin located on the burner
surface. The notch on the right end of the log should mate with the grate bar. See Figure 11.
5
LOG END
RESTS ON
FLAT SPOT
LOG END
CONTACTS
GRATE BAR
SLOT
Figure 12. Log #4
Figure 13. Log #5
Log #5 (SRV2227-706): Place the left end of the log on the flat spot of log as shown in Figure 6. The right end of log should
rest on the burner and touches the grate bar as shown in Figure 13.
MATE
NOTCH WITH
GRATE BAR
6
LOG
GROOVES
Figure 14. Place Log #6
Log #6 (SRV2227-704): Rest the left end of Log #6 on the burner. Mate the notch on the left end of log with the grate bar.
The log should rest on both log grooves as illustrated in Figure 9 and Figure 10.
2227-935B
34
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
G. Install the Log Assembly
Log Set Assembly: LOGS-QFI35
Models: QFI35, QFI35-C
CAUTION: Logs are fragile, handle with care.
SRV2225-703
SRV2225-701
SRV2225-704
SRV2225-702
SRV2225-706
SRV2225-710
SRV2225-705
Figure 1. Refractory and Logs Installed
Figure 2. Install Back Refractory
Install back refractory by placing it against the back of the firebox. The back refractory must be held in the upright position
until the side refractory is installed. Install the left side refractory as shown in Figure 3. Bend the refractory tab down as
shown in Figure 4. Repeat this step for the right refractory panel.
REFRACTORY
TAB
Figure 3. Install Side Refractory
Figure 4. Bend Refractory Tab
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
35
LOG SUPPORT
LOG PINS
1
LOG GROOVE
CONTACTS
GRATE TINE
ANDIRONS
LOG RESTS ON
LOG SUPPORT
OUTER TINES
Figure 5.
Figure 6. Location of Log #1
Log #1 (SRV2225-701): Position the groove on the log with the right grate tine as shown in Figure 6. The opposite end of
the log will rest on the log support. Rotate the opposite end of the log clockwise until it contacts the refractory panel.
FLAT SPOTS FOR LOG #6 AND LOG #3
LOG CONTACTS
LEFT REFRACTORY
PANEL
SLOT
2
MATE SLOT WITH
GRATE TINE
Figure 7. Place Log #2
Figure 8. Slot on Log #2
Log #2 (SRV2225-703): Mate the grate tine with the slot on the bottom of Log #2. The back end of the log rests on the log
support. The side of the log will contact the left refractory as shown in Figure 7.
POSITION LOG
ON FLAT SPOT
FLAT SPOT
FOR LOG #7
3
4
LOG CONTACTS LEFT
REFRACTORY PANEL
LOG RESTS ON
LOG SUPPORT
LOG CONTACTS BACK
REFRACTORY PANEL
Figure 9. Place Log #3
MATE LOG
PIN WITH
LOG SLOT
MATE GRATE BAR
WITH LOG GROOVE
Figure 10. Place Log #4
Log #3 (SRV2225-702): Position the left end of the log on the flat spot of Log #2 as shown in Figure 7 and Figure 9. The
right end of the log rests on the log support and touches the back refractory. The left end of the log should contact the left
refractory panel.
Log #4 SRV(2225-705): Mate the slot on the bottom of Log #4 with the right log pin. Refer to Figure 11 for location of log
slot. Rotate the right end of the log clockwise until the groove on the end of the log mates with the grate bar.
36
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
MATE LOG
PINS WITH
LOG SLOTS
5
LOG SLOT
Figure 11. Log #4
FLAT SPOT
FOR LOG #6
Figure 12. Place Log #5
Log #5 (SRV2225-710): Position Log #5 as shown in Figure 12. Mate the middle and left log pins with the two slots located
on the bottom of the log. See Figure 13 for locations of log slots. The smaller end should be pointed toward the right side
of the firebox.
LOG SLOTS
6
LOG RESTS
ON FLAT SPOT
LOG RESTS
ON FLAT SPOT
Figure 14. Place Log #6
Figure 13. Log #5
Log #6 (SRV2225-706): Rest the wide end of the log on the flat spot of Log #5 as shown in Figure 12 and Figure 14. Place
the narrow end on the flat spot of Log #2. Flat spot on Log #2 is indicated in Figure 7.
LOG RESTS
ON FLAT SPOT
7
LOG GROOVE
MATES WITH
GRATE BAR
Figure 15. Place Log #7
Log #7 SRV2225-704): Note the location of the groove on the underside of the log. Place the opposite end on the flat spot
on Log #3. See Figure 9. Mate the groove on the underside of the log with the grate bar as shown in Figure 15, centered
between the andirons.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
2225-935C
37
H. Fixed Glass Assembly
I. Air Shutter Setting
Removing Fixed Glass Assembly
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter is
set at the factory for minimum vertical vent run. Adjust air
shutter for longer vertical runs. See Figure 12.4.
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
NOTICE: If sooting occurs, provide more air by opening
the air shutter.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
• The glass assembly fastens to the fireplace in four
places. Four of the fastening mechanisms are springloaded glass latches. An example of the glass latch
is shown in Figure 12.3.
•
To release glass assembly, pull the two bottom
spring-loaded latches forward and allow them to retract away from the glass assembly. Slide the glass
assembly outward and downward until the top latches
disengage.
Replacing Fixed Glass Assembly
• Tilt glass assembly toward fireplace and slide glass
assembly upward to engage top latches. Verify top
latches are fully engaged and then fasten the two
bottom latches.
Figure 12.4 Air Shutter
Air Shutter Settings
NG
LP
QFI30-C
3/8 in.
1/2 in.
QFI35-C
3/8 in.
1/2 in.
Figure 12.3 Fixed Glass Assembly
38
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
13
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you
do experience a problem, this troubleshooting guide will assist a qualified technician in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified technician. Contact your dealer to
arrange a service call by a qualified technician.
A. IntelliFire™ Plus Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly
are tight; also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
A. No power, transformer installed
incorrectly, or depleted batteries.
Verify that transformer is installed and plugged into module. Check
voltage of transformer at connection to module. Acceptable readings of a good transformer are between 6.4 and 6.6 volts DC. Battery power supply voltage must be at least 4 volts. If below 4 volts,
replace batteries.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 120/VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .17 in. or 1/8 in. (3 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Pilot valve solenoid
Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
39
IntelliFire™ Plus Ignition System (continued)
Symptom
4. Pilot lights but continues to spark, and
main burner will not
ignite. (If the pilot
continues to spark
after the pilot flame
has been lit, flame
rectification has not
occurred.)
40
Possible Cause
Corrective Action
A. A shorted or loose connection in
flame sensing rod.
Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify flame sense or igniter wires are not grounding out to metal chassis, pilot burner, pilot
enclosure or screen if present, or any other metal object.
B. Poor flame rectification or contaminated flame sensing rod.
With fixed glass assembly in place, verify that flame is engulfing
flame sensing rod on left side of pilot hood. Flame sensing rod
should glow shortly after ignition. With a multi-meter, verify that
current in series between module and sense lead is at least 0.14
microamps. Verify correct pilot orifice is installed and gas inlet is set
to pressure specifications. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
Verify that wire harness is firmly connected to the module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod is not
cracked, damaged, or loose. Verify connection from flame sensing
rod to white sensor wire. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod. Verify continuity with a multi-meter with ohms set
at lowest range. Replace pilot if any damage is detected.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
14
Reference Materials
A. Appliance/Decorative Front Dimension Diagrams
Dimensions are actual appliance dimensions. Use for reference only.
A
H
S
O
Q
R
P
G
T
B
C
D
E
I
F
U
J
GAS LINE
ACCESS
L
K
MODEL DIMENSIONS
Location
M
ELECTRICAL
ACCESS
QFI35-C
N
MODEL DIMENSIONS
QFI30-C
Inches
Millimeters
Inches
Millimeters
A
23-7/16
595
20-3/16
513
B
34-5/8
879
30-5/8
C
31-5/8
803
D
15-11/16
E
Location
QFI35-C
QFI30-C
Inches
Millimeters
Inches
Millimeters
K
4-13/16
122
4-13/16
122
778
L
10-1/16
256
9-1/8
232
27-1/2
699
M
2-7/16
62
2-7/16
62
398
12-3/16
310
N
5
127
4-1/16
103
24-1/16
611
20-7/16
519
O
5-1/8
130
5-1/8
130
F
21-1/8
537
17-5/8
448
P
8-15/16
227
8-15/16
227
G*
15-11/16
403
14-5/8
372
Q
1-13/16
46
1-15/16
49
H
11-3/4
298
10-1/16
256
R
3-1/4
83
3-1/4
83
I
20-7/16
518
17
432
S
5-5/16
135
4-15/16
125
J
1-3/4
44
1-3/4
44
T
10-5/8
270
9-1/2
235
U
4-11/16
119
4-5/8
118
*Note: Location G on Figure 14.1 is measuring the appliance depth, for installation depth reference Location G on
Figure 5.2.

Figure 14.1 Appliance Dimensions
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
41
AF-QFI30, AF-QFI35 DECORATIVE FRONTS
D
E
F
B
A
C
G
AF-QFI30
AF-QFI35
A
B
C
D
E
F
G
in.
30
13-1/2
4-5/8
36
23-11/16
23-3/16
1/2
mm
762
343
117
914
602
589
13
in.
32
16
4-5/8
38
25-11/16
25-3/16
1/2
mm
813
406
117
965
652
640
13
FSP-QFI30, FSP-QFI35 DECORATIVE FRONTS
D
E
F
B
A
C
G
FSP-QFI30
FSP-QFI35
 Figure 14.2
42
A
B
C
D
E
F
G
in.
27
11-5/8
5-1/2
36
23-11/16
23-3/16
1/2
mm
686
279
140
914
602
589
13
in.
29-1/4
16-1/16
4-15/16
38
25-11/16
25-3/16
1/2
mm
743
408
125
965
652
640
13
Decorative Front Dimensions
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
TP-QFI30/TP-QFI35 DECORATIVE FRONTS
D
E
F
B
A
C
G
TP-QFI30
TP-QFI35
 Figure 14.3
A
B
C
D
E
F
G
in.
32-15/16
12-9/16
4-5/8
36
23-1/2
23
1/2
mm
837
319
117
914
597
584
13
in.
35
15-9/16
4-11/16
38-1/16
26-1/2
26
1/2
mm
889
395
119
967
673
660
13
Decorative Front Dimensions
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
43
B. Vent Kits Components
Direct Vent Flex Liner Kits (see Figure 14.4)
LINK-DV30B: Masonry 3 inch flex liner kit. Expands to 30
feet. Includes: two liners, termination cap and flashing.
LINK-DV4-30B: Masonry 3 inch flex liner kit. Expands to 30
feet and 4 feet respectively. Includes: two liners, termination
cap and flashing.
LINK-ZC-ADPB
LINKSQC-DV30, LINKSQB-DV30: Masonry 3 inch flex liner
kit. Expands to 30 feet. Includes: two liners, termination
cap and flashing.
LINKSQC-DV4-30, LINKSQB-DV4-30: Masonry 3 inch
flex liner kit. Expands to 30 feet and 4 feet respectively.
Includes: two liners, termination cap and flashing.
DV-46DVA-GK
FLEX3-30
LINKSQC-DV30 (COPPER)
LINKSQB-DV30 (BLACK)
LINK-DV30B
FLEX-CNCT
Figure 14.5 Direct Vent Flex Liner Accessory Kits
LINK-DV4-30B
LINKSQC-DV4-30 (COPPER)
LINKSQB-DV4-30 (BLACK)
Figure 14.4 Direct Vent Flex Liner Kits
Direct Vent Flex Liner Accessory Kits (see Figure 14.5)
LINK-ZC-ADPB: Zero clearance chimney adapter
DV-46DVA-GK: Adapter kit - It is permissible to use DV46DVA-GK to connect collinear flex vent to SL-D vent pipe
to extend the run.
FLEX3-30: One 3 inch flexible liner expands to 30 feet.
FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner,
one connector per kit.
44
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
R
QFI30-C
C. Service
Parts
Service
Parts
Beginning Manufacturing Date: Aug 2011
Ending Manufacturing Date: Active
30” Gas Insert - DV
Log Set Assembly
7
8
1
5
9
2
6
3
10
4
11
17
14
12
13
15
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
Log Assembly
LOGS-QFI30
1
Log 1
SRV2227-703
2
Log 2
SRV2227-702
3
Log 3
SRV2227-701
4
Log 4
SRV2227-705
5
Log 5
SRV2227-706
6
Log 6
SRV2227-704
7
Termination Plate Assembly
Pre 0023696931
2206-012
Post 0023696931
2206-013
Flex Pipe Handle
16
Y
438-351
Gasket
Pre 0023696931
2206-401
Post 0023696931
2206-178
8
Grate Assemby
2227-016
9
Burner Assembly
2227-009
10
Base Pan
2206-127
Y
11
Glass Door Assembly
GLA-2206
Y
12
Rheostat Knob
100-512
Y
13
Control Panel
2205-129
14
Rheostat
2206-800
Y
15
Blower
GFK-210-C
16
Wire Assembly
2206-068
Y
17
Cord Assembly
2201-017
Y
2206-085
Y
Qty 2 req
Fuse Wire Assembly
Additional service part numbers appear on following page.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
3/15
45
R
QFI35-C
Service Parts
Beginning Manufacturing Date: Aug 2011
Ending Manufacturing Date: Active
35” Gas Insert - DV
8
Log Set Assembly
9
10
3
2
6
5
11
7
1
4
18
12
15
13
14
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
LOGS-QFI35
1
Log 1
SRV2225-701
2
Log 2
SRV2225-703
3
Log 3
SRV2225-702
4
Log 4
SRV2225-705
5
Log 5
SRV2225-710
6
Log 6
SRV2225-706
7
Log 7
SRV2225-704
8
Termination Plate Assembly
Pre 0023696931
2205-012
Post 0023696931
2205-013
Y
438-351
Gasket
Pre 0023696931
2206-401
Post 0023696931
2206-178
9
Grate Assemby
2225-016
10
Burner Assembly
2225-009
11
Base Pan
2205-127
12
Y
Glass Door Assembly
GLA-2205
Y
13
Rheostat Knob
100-512
Y
14
Control Panel
2205-129
15
On/Off Rheostat
2206-800
Y
16
Blower Assembly
GFK-210-C
17
Power Cord Assembly
2206-068
Y
18
Cord Assembly
2201-017
Y
2206-085
Y
Qty 2 req
Fuse Wire Assembly
Additional service part numbers appear on following page.
46
Stocked
at Depot
Log Assembly
Flex Pipe Handle
17
16
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
3/15
R
QFI30-C, QFI35-C
Service Parts
Beginning Manufacturing Date: Aug 2011
Ending Manufacturing Date: Active
#19 Valve Assembly
19.4
19.5
19.3
19.2
19.1
19.8
19.7
19.6
19.17
1916 19.15
19.14
19.9
19.13
19.10
19.11
19.12
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
19.1
Grommet, 3 Hole
2118-420
19.2
Pilot Shield
2206-120
Pilot Assembly NG
2202-013
Pilot Assembly LP
2202-014
Y
Ori¿ce NG (#35C)
582-835
Y
582-851
Y
582-833
Y
19.3
19.4
QFI30-C
Ori¿ce LP (#51C)
Ori¿ce NG (#33C)
QFI35-C
Ori¿ce LP (#50C)
Y
582-850
Y
19.5
Flexible Gas Connector
530-302A
Y
19.6
Control Panel Bracket
2205-128
19.7
Valve Bracket
2205-146
19.8
Flex Ball Valve Assembly
302-320A
Y
Valve NG
2166-302
Y
Valve LP
2166-303
Y
303-315/5
Y
Y
19.9
19.10
Brass Connector
Pkg of 5
19.11
Remote Jumper Wire
2103-013
19.12
Jumper Wire
2187-198
19.13
**Battery Pack
2166-323
Y
19.14
Wire Harness
2166-304
Y
19.15
Power Supply
2326-131
Y
19.16
Module
2166-307
Y
19.17
Thermostat Assembly
046-018A
Y
**Fuse for battery pack can be sourced locally, not a warranty item. Specs are 250v, 1A fuse, 3/4" long
Additional service part numbers appear on following page.
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
47
R
QFI30-C, QFI35-C
Service Parts
Beginning Manufacturing Date: Aug 2011
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Gasket Assembly
PART NUMBER
2206-081
Includes Air Passage, Valve Plate, Exhaust Bottom, Exhaust Top, and Burner Neck Gaskets
Glass Clip Support Assembly, Bottom
Qty 2 req
2155-045
Y
Glass Latch Assembly, Top
Qty 2 req
339-121A
Y
Lava Rock
4021-296
Mineral Wool
050-721
Refractory Assembly (sold as set only)
QFI30-C
BRICK-QI30
QFI35-C
BRICK-QI35
Rheostat/Temp Sensor Assembly
SRV2206-800
Touch Up Paint
TUP-GBK-12
EMC Filter
2201-198
Y
QFI30-C
Conversion Kit NG
NGK-I30-C
Y
Conversion Kit LP
LPK-I30-C
Y
Pilot Ori¿ce NG
593-528
Y
Pilot Ori¿ce LP
593-527
Y
Regulator NG
NGK-DXV-50
Y
Regulator LP
LPK-DXV-50
Y
Conversion Kit NG
NGK-I35-C
Y
Conversion Kit LP
LPK-I35-C
Y
Pilot Ori¿ce NG
593-528
Y
Pilot Ori¿ce LP
593-527
Y
Regulator NG
NGK-DXV-50
Y
Regulator LP
LPK-DXV-50
Y
QFI35-C
48
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
D. Contact Information
R
Quadra-Fire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the location of your nearest Quadra-Fire dealer,
please visit www.quadrafire.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5613487, 5647340, 5890485,
5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269,
7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945C
Printed in U.S.A. - Copyright 2015
Quadra-Fire • QFI30-C, QFI35-C • 2227-901 Rev. Q • 3/15
49