Sierra Wireless RJ-11 User guide

User Guide
NTC-30WV – 3G Outdoor WiFi Router with Voice
Copyright
Copyright© 2014 NetComm Wireless Limited. All rights reserved.
The information contained herein is proprietary to NetComm Wireless. No part of this document may be translated, transcribed,
reproduced, in any form, or by any means without prior written consent of NetComm Wireless.
Note: This document is subject to change without notice.
Save our environment
When this equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separately from
domestic waste.
The cardboard box, the plastic contained in the packaging, and the parts that make up this device can be recycled in accordance
with regionally established regulations. Never dispose of this electronic equipment along with your household waste. You may be
subject to penalties or sanctions under the law. Instead, ask for disposal instructions from your municipal government.
Please be responsible and protect our environment.
This manual covers the following products:
NetComm Wireless NTC-30WV
DOCUMENT VERSION
1.0 - Initial document release
DATE
29/01/2014
Table 1 - Document Revision History
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
2
www.netcommwireless.com
Table of Contents
Overview ........................................................................................................................................................................................ 5
Introduction ................................................................................................................................................................................................... 5
Target audience............................................................................................................................................................................................. 5
Professional Installation Instructions ............................................................................................................................................................... 5
Prerequisites ................................................................................................................................................................................................. 6
Notation ........................................................................................................................................................................................................ 6
Product introduction...................................................................................................................................................................... 7
Product overview ........................................................................................................................................................................................... 7
Package contents.......................................................................................................................................................................................... 7
Product features ............................................................................................................................................................................................ 8
Hardware overview ........................................................................................................................................................................ 9
LED indicators ............................................................................................................................................................................................... 9
Physical Dimensions .................................................................................................................................................................................... 11
Interfaces .................................................................................................................................................................................................... 13
Implementation and Deployment Scenario ................................................................................................................................ 15
Installation and Configuration of the NTC-30WV ....................................................................................................................... 16
Hardware Installation ................................................................................................................................................................................... 16
Powering the Router via DC Power Supply ................................................................................................................................................... 16
Installing the router ...................................................................................................................................................................................... 16
Powering the Router via a Power over Ethernet (PoE) Cable (Optional) .......................................................................................................... 17
Connecting wirelessly .................................................................................................................................................................................. 18
Advanced configuration .............................................................................................................................................................. 19
Status ........................................................................................................................................................................................... 20
Networking ................................................................................................................................................................................... 23
Data Connection.......................................................................................................................................................................................... 23
Operator settings ......................................................................................................................................................................................... 27
SIM security settings .................................................................................................................................................................................... 28
LAN ............................................................................................................................................................................................................ 34
Wireless Settings ......................................................................................................................................................................................... 38
Routing ....................................................................................................................................................................................................... 46
VPN ............................................................................................................................................................................................................ 56
Services........................................................................................................................................................................................ 69
Dynamic DNS .............................................................................................................................................................................................. 69
Network time (NTP)...................................................................................................................................................................................... 70
Data stream manager .................................................................................................................................................................................. 71
Watchdogs.................................................................................................................................................................................................. 75
SNMP ......................................................................................................................................................................................................... 78
TR-069........................................................................................................................................................................................................ 80
Auto Dial Configuration ................................................................................................................................................................................ 82
USSD .......................................................................................................................................................................................................... 83
SMS messaging .......................................................................................................................................................................................... 84
Diagnostics ................................................................................................................................................................................................. 88
Sending an SMS Diagnostic Command ........................................................................................................................................................ 91
System ......................................................................................................................................................................................... 99
Log ............................................................................................................................................................................................................. 99
System Configuration................................................................................................................................................................................. 102
HTTPS key management ........................................................................................................................................................................... 109
SSH Key Management .............................................................................................................................................................................. 112
Appendix A: Tables.................................................................................................................................................................... 116
Appendix B: Default Settings .................................................................................................................................................... 117
Restoring factory default settings ............................................................................................................................................................... 118
Appendix C: Recovery mode .................................................................................................................................................... 119
Accessing recovery mode .......................................................................................................................................................................... 119
Status ....................................................................................................................................................................................................... 120
Log ........................................................................................................................................................................................................... 120
Application Installer .................................................................................................................................................................................... 121
Settings ..................................................................................................................................................................................................... 121
Reboot ...................................................................................................................................................................................................... 121
Appendix D: HTTPS - Uploading a self-signed certificate ....................................................................................................... 122
Technical Data ........................................................................................................................................................................... 124
Additional Product Information ................................................................................................................................................. 125
Using the NTC-30WV to make and receive telephone calls ......................................................................................................................... 125
Legal & Regulatory Information................................................................................................................................................. 130
Intellectual Property Rights ......................................................................................................................................................................... 130
Customer Information ................................................................................................................................................................................ 130
Consumer Protection Laws ........................................................................................................................................................................ 130
Product Warranty ...................................................................................................................................................................................... 131
Limitation of Liability ................................................................................................................................................................................... 131
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
3
Contact....................................................................................................................................................................................... 132
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
4
www.netcommwireless.com
Overview
Introduction
This document provides you all the information you need to set up, configure and use the NetComm Wireless NTC-30WV router.
Target audience
This document is intended for system integrators or experienced hardware installers who understand telecommunications
terminology and concepts.
Professional Installation Instructions
Please be advised that due to the unique functions supplied by this product, the device is intended for use with licensed thirdparties only. The product will be distributed through controlled distribution channels and should be installed by trained professionals.
1.
Installation Personnel
This product is designed for specific applications and needs to be installed by qualified personnel who have RF and related rule
knowledge.
2.
Installation Location
The product shall be installed at a location where the radiating antenna can be kept at least 30cm from a nearby person in normal
operation conditions to meet regulatory RF exposure requirements.
3.
External Antenna
Use only antennae which have been approved by NetComm Wireless Limited. Non-approved antennae may produce unwanted
spurious or excessive RF transmitting power which may lead to the violation of regulatory compliance and is prohibited.
4.
Installation Procedure
Please refer to the rest of this manual for further details.
5.
Warning
Please carefully select the installation position and make sure that the final output power does not exceed the limit set in relevant
rules. Violation of the rules could lead to serious federal penalties.
The following maximum Transmit powers should be observed during configuration:
PEAK TRANSMIT POWER
802.11b
16.29 dBm
802.11g
23.98 dBm
802.11n – 20 MHz
24.51 dBm
802.11n – 40 MHz
24.06 dBm
Table 2: Maximum Transmit Power Levels
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
5
Prerequisites
Before continuing with the installation of your NTC-30WV router, please confirm that have the following:
A device with a working Ethernet network adapter.
A web browser such as Internet Explorer, Mozilla Firefox or Google Chrome.
A flathead screwdriver if field terminated power is required.
Telephony Requirements
Standard analogue PSTN or cordless PSTN phone handset (DECT) with an RJ-11 port.
(ISDN phone handsets are not supported)
RJ-11 cable
Notation
The following symbols are used in this user guide:
The following note requires attention.
The following note provides a warning.
The following note provides useful information.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
6
www.netcommwireless.com
Product introduction
Product overview
The NetComm Wireless outdoor router (NTC-30WV) is designed to deliver high speed internet to homes and businesses with
otherwise little to no Internet access available. The NTC-30WV is a robust 3G (HSPA+) router which can be pole or wall mounted
and connects to a 3G network. The NTC-30WV features a powerful antenna system and wireless radio together in a single unit. This
tight integration between the radio receiver and antenna system in an outdoor unit provides great benefits to signal strength
compared with separated solutions involving signal degradation along lengthy antenna cabling.
The integrated telephone adapter connects a standard analogue phone handset to the NTC-30WV. It allows for phone calls to be
made over the 3G UMTS network for a full landline replacement. The router integrates a powerful Sierra Wireless module (MC8704)
and delivers download speeds of up to 21Mbps which is then transmitted via Ethernet to a WiFi router inside the property.
Power may be optionally delivered to the outdoor router via Power over Ethernet technology making installation quick and easy as
there is no power source required at the outdoor mount point, and both power and data can be provided via a single cable from
inside the property. With an IP67 rating, the device also withstands diverse temperature and weather environments.
Package contents
The NTC-30WV series package consists of:
NetComm NTC-30WV - Outdoor HSPA+ WiFi Router
2 x WiFi Antennas (N Type female)
2 x 3G Antennas (N Type female)
Mounting Bracket
4 x Wall mounting screws (Diameter = 6mm, Length = 25mm)
4 x Mounting screws (Diameter = 6mm, Length = 14.85mm)
IP67 Water-proof Plug Cable Gland
Ferrite Core
2 x Hose Clamps for pole mounting
Wireless Security Card
DC Power cable 10m (open ended)
If any of these items are missing or damaged, please contact NetComm Support immediately by visiting the NetComm Support
website at: http://www.netcommwireless.com/contact-forms/support
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
7
Product features
Industrial-grade outdoor fixed wireless data gateway designed for rugged deployments in remote environments and
industrial applications
Ideal for providing primary and backup wireless connectivity over 3G UMTS networks
Maximum data speed in downlink 21Mbps (HSDPA) and 5.76Mbps in uplink (HSUPA)
Embedded high-performance 3G cellular modem supporting HSPA+/EDGE/GPRS
IP67 and environmentally rated chassis to withstand extreme weather conditions
Extended temperature tolerance in operation -25 to 75°C
2.4 GHz band wireless LAN access point with 2x2 MIMO antenna technology
IEEE 802.11n standard for wireless data speeds up to 300Mbps
1
Ethernet 10/100 connectivity with optional Power over Ethernet Injector for universal deployment
Analogue telephone connectivity (CS Voice) for complete landline replacement (optional configuration)
Wide DC power input range to suit diverse installation environments
Built-in VPN clients for a secure connection over a public cellular network
1
Maximum wireless signal rate and coverage values are derived from IEEE Standard 802.11g and 802.11n specifications. Actual
wireless speed and coverage are dependent on network and environmental conditions included but not limited to volume of
network traffic, building materials and construction/layout.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
8
www.netcommwireless.com
Hardware overview
LED indicators
The NTC-30WV uses 7 LEDs to display the current system and connection status.
Figure 1 - NTC-30WV LED Indicators
LED INDICATOR
ICON
COLOUR
DEFINITION
High Signal
Green
High 3G Signal strength available.
Medium to High Signal
Green
Medium to High 3G Signal strength available.
Medium Signal
Green
Medium 3G Signal strength available.
Low to Medium Signal
Green
Low to Medium 3G Signal strength available.
Low Signal
Green
Low 3G Signal strength available.
Internet
Green
Router is currently connected to the Internet.
Power
Red
Unit is powered on.
Table 3 - LED Indicators
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
9
The 5 signal strength LEDs also indicate whether the device is MEP locked, SIM is not inserted and if the SIM is PIN or PUK locked
by flashing in certain patterns. Below is a table outlining the various LED flash sequences and their meanings.
LED PATTERN
DESCRIPTION
All signal LEDs flash ON and OFF
every 2 seconds
SIM not inserted
The signal LEDs flash in a pattern with
one, three and 5 LEDs flashing in a
sequence.
MEP Lock
The signal LEDs flash in a sequential
order starting with the Low signal LED
to the High signal LED.
SIM is PIN locked
The signal LEDs flash in a sequential
order starting with the High signal LED
to the Low signal LED.
SIM is PUK locked
Table 4 - SIM Lock LED Statuses
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
10
www.netcommwireless.com
Physical Dimensions
The physical dimensions of the NTC-30WV, antennas and the included mounting bracket which can be used to attach the NTC30WV to a pole or to provide a wall / ceiling mount are listed below.
Figure 2 – NTC-30WV Dimensions
NTC-30WV
(WITHOUT ANTENNAS ATTACHED)
Length
255 mm
Depth
80 mm
Height
240 mm
1750 g
Weight
(w/o mounting bracket and antennas)
Table 5 - Device Dimensions
Figure 3 – NTC-30WV Mounting Bracket
NTC-30WV MOUNTING BRACKET
Length
110 mm
Depth
12 mm
Height
290 mm
410 g
Weight
(w/o NTC-30WV attached)
Table 6 - Mounting Bracket Dimensions
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
11
Figure 4 - NTC-30WV Antenna
NTC-30WV 3G AND WIFI ANTENNA
Length
180 mm
Diameter
20 mm
60 g
Weight
(w/o NTC-30WV attached)
Table 7 - Antenna Dimensions
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
12
www.netcommwireless.com
Interfaces
The following interfaces are available on the NTC-30WV:
1
2
3
4
5
6
Figure 5 - Bottom Mounted Interfaces
ITEM
INTERFACE
FUNCTION
1
WiFi Antenna Connector (TNC)
Connect one of the WiFi antennas here.
2
DC Power Port
Connect the optional DC Power supply to the NTC-30WV.
3
10/100Base-TX Ethernet RJ-45 (w/Auto MDX) Port
Connect the NTC-30WV to an Ethernet enabled device or Switch and deliver power
through Power over Ethernet (PoE) technology.
4
RJ-11 Port.
An analogue phone handset can be connected to the RJ-11 to make calls over the 3G
network.
The reset button has multiple functions.


5
Reset

SIM Card Reader
6
WiFi Diversity Antenna Connector (TNC)
Reboot the device: Press and hold the reset button down for no longer
than 5 seconds. All LEDs remain off, when the button is released the green
LEDs flash once and the router reboots.
Reboot to recovery mode: Press and hold the reset button down for
between 5 and 15 seconds. When the LEDs are flashing, release the button
and the “www” LED flashes. The router reboots into recovery mode.
Factory reset the device: Press and hold the reset button down for more
than 15 seconds. When all the LEDs are off, release the button. The Red
LED flashes to confirm the factory reset process. If you change your mind
after holding the reset button down for more than 15 seconds, you can
cancel the factory reset by removing the power source before releasing the
button or by releasing the button and quickly pressing it once more.
Insert an active SIM to provide 3G connectivity.
Connect one of the WiFi antennas here.
Table 8 - Bottom Mounted Integrated Interfaces
1
2
Figure 6 - Top Mounted Interfaces
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
13
ITEM
INTERFACE
1
1 x 3G Main antenna connector (Type N)
2
1 x 3G Aux antenna connector (Type N)
FUNCTION
Connect one of the 3G antennas here.
Connect one of the 3G antennas here.
Table 9 - Top Mounted Interfaces
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
14
www.netcommwireless.com
Implementation and
Deployment Scenario
The NTC-30WV is a robust 3G (DC-HSPA+) router that connects to the 3G network and is mounted either on the wall or a pole and
positioned in an optimal position on the outside of a property. The NTC-30WV features a powerful antenna system and radio
modem together in the one unit in an outdoor location. This tight integration between the radio receiver and antenna system in an
outdoor unit provides great benefits to signal strength compared with alternate separated solutions involving signal degradation
along lengthy antenna cabling.
Figure 7 - Typical NTC-30WV Deployment - House
Power is delivered to the outdoor router via Power over Ethernet technology (as shown above) making installation quick and easy as
there is no power source required at the outdoor mount point, and both power and data can be provided via a single cable from
inside the property. With an IP67 rated enclosure, the device also withstands diverse temperature and weather environments.
Utilising an 802.11n WiFi repeater further increases the WiFi range of the NTC-30WV meaning a wireless connection is possible in
all corners of your house or property.
The NTC-30WV is able to be mounted either to a pole or secured directly to a wall, allowing flexibility in the choice of an installation
location.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
15
Installation and Configuration
of the NTC-30WV
Hardware Installation
Please refer to the NTC-30WV Quick Start Guide (available from the NetComm Wireless website) for instructions on assembling,
mounting and placing the NTC-30WV.
Powering the Router via DC Power Supply
Below is a diagram summarising the assembly when connecting via DC power supply. Please refer to page 7 of the Quick Start
Guide for more detail on how to connect the NTC-30WV via DC Power Supply.
Figure 8 - Example of how to connect the NTC-30WV when connecting via DC power supply
Installing the router
After you have mounted the router and connected a power source, follow these steps to complete the installation process.
1.
Connect equipment that requires network access to the Ethernet port of your router. This may be your computer for
advanced configuration purposes, or your end equipment which requires data access via the NTC-30WV router. You can
connect one device directly, or several devices using a network switch.
2.
Ensure the external power source is switched on and wait 2 minutes for your NTC-30WV router to start up. To check the
status of your router, compare the LED indicators on the device with those listed in the LED Indicators section of this
guide.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
16
www.netcommwireless.com
Powering the Router via a Power over Ethernet (PoE) Cable
(Optional)
Please refer to the Installation Guide for step-by-step instructions on connecting the devices.
Below is a diagram summarising the assembly when connecting via optional Power over Ethernet cable.
Figure 9 – Example of how to connect the NTC-30WV when connecting via optional Power over Ethernet (PoE) cable
Note: The DC Injector supplies 48V. Do not use this power supply for anything except for powering the outdoor gateway.
Captive Power Terminal Block
The following table displays the pin outs for the Locking Power Block on the PoE Injector.
Figure 10 - Locking Power Terminal Block
PIN
SIGNAL
DESCRIPTION
1
V+
Voltage+
2
GND
Ground
3
V-
Voltage-
Table 10 - Locking Power Block Pin Outs
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
17
Figure 11 - Assembly of the PoE Injector and the Captive Terminal Block
Connecting wirelessly
1.
Ensure WiFi is enabled on your device (e.g. computer/laptop/smartphone).
2.
Scan for wireless networks in your area and connect to the network name that matches the Wireless network name
configured on the NTC-30WV. The default wireless network name is printed on the security card included in the package.
3.
When prompted for your wireless security settings, enter the Wireless security key configured on the NTC-30WV.
4.
Wait approximately 30 seconds for the connection to establish.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
18
www.netcommwireless.com
Advanced configuration
The NTC-30WV router comes with pre-configured settings that should suit most customers. For advanced configuration, log in to
the web-based user interface of the router.
To log in to the web-based user interface:
1.
Open a web browser (e.g. Internet Explorer, Firefox, Safari), type http://192.168.1.1 into the address bar and press Enter.
The web-based user interface log in screen is displayed.
Figure 12 – Log in prompt for the web-based user interface
2.
Enter the login username and password. If this is the first time you are logging in or you have not previously configured the
password for the “root” or “admin” accounts, you can use one of the default account details to log in.
ROOT MANAGER
ACCOUNT
Username:
root
Password:
admin
Table 11 - Management account login details – Root manager
ADMIN MANAGER ACCOUNT
Username:
admin
Password:
admin
Table 12 - Management account login details – Admin manager
Note: To access all features of the router, you must use the root manager account.
For security reasons, we highly recommend that you change the passwords for the root and admin accounts upon initial
installation. You can do so by navigating to the System and then Administration page.
The Status page is displayed when you have successfully logged in.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
19
Status
The status page of the web interface provides system related information and is displayed when you log in to the NTC-30WV router
management console. The status page shows System information, LAN details, Cellular connection status, Packet data connection
status and Advanced status details. You can toggle the sections from view by clicking the
or
buttons to show or hide
them. Extra status boxes will appear as additional software features are enabled (e.g. VPN connectivity).
Figure 13 - The Status page
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
20
www.netcommwireless.com
ITEM
DEFINITION
System information
System up time
The current uptime of the router.
Board version
The hardware version of the router.
Serial number
The serial number of the router.
Firmware version
The firmware version of the router
Model
The type of phone module and the firmware version of the module.
Module firmware
The firmware revision of the phone module.
IMEI
The International Mobile Station Equipment Identity number used to uniquely identify a mobile device.
Hardware
The hardware version of the module.
LAN
IP
The IP address and subnet mask of the router.
MAC address
The MAC address of the router.
Ethernet port status
Displays the current status of the Ethernet port and its operating speed.
Cellular connection status
SIM Status
Displays the activation status of the router on the carrier network.
Signal strength (dBm)
The current signal strength measured in dBm
Network registration status
The status of the router’s registration for the current network.
Operator selection
The mode used to select an operator network.
Current operator
The current operator network in use.
Roaming status
The roaming status of the router.
Allowed bands
The bands to which the router may connect.
Current band
The current band being used by the router.
Coverage
The type of mobile coverage being received by the router.
WWAN connection status
Profile name
The name of the active profile.
Status
The connection status of the active profile.
Default profile
Indicates whether the current profile in use is the default profile.
WWAN IP
The IP address assigned by the mobile broadband carrier network.
DNS server
The primary and secondary DNS servers for the WWAN connection.
APN
The Access Point Name currently in use.
Connection uptime
The length of time of the current mobile connection session.
Advanced status
Mobile country code
The Mobile Country Code (MCC) of the router.
Mobile network code
The Mobile Network Code (MNC) of the router.
Signal quality (Ec/N0)
A measurement of the portion of the received signal that is usable. This is the signal strength minus the signal noise level.
Received signal code power
(RSCP)
The power level of the signal on the current connection’s particular channel.
HSUPA category
Displays the HSUPA category (1-9) for the current uplink
HSDPA category
Displays the HSDPA category (1-8) for the current downlink.
SIM ICCID
The Integrated Circuit Card Identifier of the SIM card used with the router, a unique number up to 19 digits in length.
Primary scrambling code (PSC)
The Primary scrambling code for the current signal.
Location area code (LAC)
The ID of the cell tower grouping the current signal is broadcasting from.
Routing area code (RAC)
A subdivision of the location area used with GPRS.
IMSI
The International mobile subscriber identity is a unique identifier of the user of a cellular network.
Cell ID
A unique code that identifies the base station from within the location area of the current mobile network signal.
Channel number (UARFCN)
The channel number of the current 3G/2G connection.
Module PRIID Revision
Module version used for customization.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
21
Module PRIID PRI part number
The part number of the Module PRIID.
Table 13 - Status page item details
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
22
www.netcommwireless.com
Networking
The Networking section provides configuration options for Wireless WAN, LAN, Routing and VPN connectivity.
Data Connection
The data connection page allows you to configure and enable/disable the connection profile. To access this page, click on the
Networking menu, and under the Wireless WAN menu, select the Data connection item.
Figure 14 – Data connection settings
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
23
ITEM
DEFINITION
Data connection
Transparent Bridge (PPPoE)
Toggles the transparent bridge function on and off.
Profile name list
Default
Sets the corresponding profile to be the default gateway for all outbound traffic except traffic for which there are
configured static route rules or profile routing settings.
Status
Toggles the corresponding profile on and off. If your carrier supports it, two profiles may be turned on simultaneously.
APN
The APN configured for the corresponding profile.
Username
The username used to log on to the corresponding APN.
Roaming settings
Allow data roaming
When set to ON, the router will allow local devices to access the Wireless WAN network when the it is roaming onto a
foreign network. When set to OFF, the router will deny network access to data services when roaming onto a foreign
network. This setting is OFF by default.
Table 14 - Data connection item details
Connecting to the mobile broadband network
The router supports the configuration of up to six APN profiles; these profiles allow you to configure the settings that the router will
use to connect to the 2G/3G network and switch easily between different connection settings.
For advanced networking purposes, you may activate a maximum of two profiles simultaneously (dependant on network support).
When activating two connection profiles, you should avoid selecting two profiles with the same APN as this can cause only one
profile to connect. Similarly, activating two profiles which are both configured to automatically determine an APN can cause a
conflict and result in neither profile establishing a connection. We recommend that the two active connection profiles have differing,
manually configured APNs to avoid connection issues and ensure smooth operation.
Manually configuring a connection profile
To manually configure a connection profile:
1.
Click the Edit button corresponding to the Profile that you wish to modify. The data connection profile settings page is
displayed.
Figure 15 - Data connection profile settings
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
24
www.netcommwireless.com
2.
Click the Profile toggle key to turn the profile on. Additional settings appear.
Figure 16 - Data connection settings - Profile turned on
3.
In the Profile name field, enter a name for the profile. This name is only used to identify the profile on the router.
4.
Ensure that the Automatic APN selection toggle key is set to off. If it is not, click it to toggle it to the off position.
5.
In the APN field, enter the APN Name (Access Point Name) and if required, use the Username and Password fields to
enter your login credentials.
6.
Next to Authentication type, select either CHAP or PAP depending on the type of authentication used by your provider.
7.
The Reconnect delay field specifies the number of seconds to wait between connection attempts. The default setting of 30
seconds is sufficient in most cases but you may modify it to wait up to 65535 seconds if you wish.
8.
The Reconnect retries field specifies the number of times to attempt a network connection if the router fails to establish a
connection. It is set to 0 by default which causes the router to attempt to reconnect indefinitely.
9.
The Metric value is used by router to prioritise routes (if multiple are available) and is set to 20 by default. This value is
sufficient in most cases but you may modify it if you are aware of the effect your changes will have on the service.
10. The MTU field allows you to modify the Maximum Transmission Unit used on the connection. Do not change this unless
instructed to by your carrier.
11. Use the NAT Masquerading toggle key to turn NAT Masquerading on or off. NAT masquerading, also known simply as
NAT is a common routing feature which allows multiple LAN devices to appear as a single WAN IP via network address
translation. In this mode, the router modifies network traffic sent and received to inform remote computers on the internet
that packets originating from a machine behind the router actually originated from the WAN IP address of the router’s
internal NAT IP address. This may be disabled if a framed route configuration is required and local devices require WAN IP
addresses.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
25
12. For advanced networking such as using dual simultaneous PDP contexts, you may wish to configure a particular profile to
route only certain traffic via that profile by configuring a custom address and mask of traffic to send via that profile. To do
this, in the Profile routing settings section, enter the Network address and Network mask of the remote network. If you do
not want to use this feature, or are unsure, please leave these fields blank, which will not designate any particular traffic to
be routed via this profile. For more information on configuring Profile routing settings, see the Setting a default gateway
with two active connection profiles example.
13. Click the Save button when you have finished entering the profile details.
Confirming a successful connection
After configuring the packet data session, and ensuring that it is enabled, click on the Status menu item at the top of the page to
return to the Status page. When there is a mobile broadband connection, the WWAN section is expanded showing the details of
the connection and the Status field displays Connected. To see details on the connected session, you can click the Show data
usage button.
Figure 17 - WWAN connection status section
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
26
www.netcommwireless.com
Operator settings
The Operator settings page enables you to select which frequency band you will use for your connection and enables you to scan
for available network operators in your area.
Figure 18 - Band settings
Note: In order to change the operator’s band settings, the data connection must be disabled. When you access this page,
you are prompted to disable the data connection if it is already active.
You may want to do this if you’re using the router in a country with multiple frequency networks that may not all support High Speed
Packet Access (HSPA). You can select the router to only connect on the network frequencies that suit your requirements.
Use the Change band drop down list to select the band you wish to use.
The following band settings options are available:
NTC-30WV
WCDMA 900/2100
WCDMA All
GSM ALL
GSM 900/1800
All bands
Table 15 - Band settings
It is not necessary to change the default setting of All bands in most cases. In fact, locking to a particular band can cause
connection difficulties if the device is moved to a location where the forced band selection is no longer available.
When All bands is selected, the router attempts to find the most suitable band based on the available networks for the inserted SIM
card.
The GSM All and the WCDMA all options allow you to force the device to lock to either 2G networks only, or 3G networks only.
Click the Save button to save and apply your selection.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
27
Operator settings
The operator settings feature allows you perform a scan of available networks, and to optionally lock to a particular network
returned by the network scan. To scan for available networks, set the Select operator mode from automatic to Manual then click the
scan button. This operation can take a few minutes and requires that the packet data session be disconnected prior to scanning.
Figure 19 - Operator settings
A list of the detected 3G service carriers in your area is displayed.
Figure 20 - Detected operator list
Select the most appropriate 3G service from the list shown and click Apply.
When Select operator mode is set to Automatic, the router selects the most appropriate operator based on the inserted SIM card.
This is the default option and is sufficient for most users.
SIM security settings
The SIM security settings page can be used for authenticating SIM cards that have been configured with a security PIN.
Unlocking a PIN locked SIM
If the SIM card is locked, you will receive a notice when you access the Status page after which you will be directed to the PIN
settings page to enter the PIN. The PIN settings page lists the status of the SIM at the top of the page.
If you are not redirected to the PIN settings page, to unlock the SIM:
a)
Click on the Networking menu from the top menu bar, and then click SIM security settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
28
www.netcommwireless.com
Figure 21 - SIM security settings - SIM PIN locked
b)
Enter the PIN in the Current PIN field and then enter it again in the Confirm current PIN field to confirm the PIN.
c)
If you are placing the router in a remote, unattended location, you may wish to check the Remember PIN option. This
feature allows the router to automatically send the PIN to the SIM each time the SIM asks for it (usually at power up). This
enables the SIM to be PIN locked (to prevent unauthorised re-use of the SIM elsewhere), while still allowing the router to
connect to the cellular service.
When this feature is enabled, the PIN you enter when setting the Remember PIN feature is encrypted and stored locally on
the router. The next time the SIM asks the router for the PIN, the router decrypts the PIN and automatically sends it to the
SIM without user intervention.
When this feature is disabled and the SIM is PIN locked and the PIN must be manually entered via the router‘s
configuration interface. In situations where the router will be unattended, this is not desirable.
Note: Select Remember PIN if you do not want to enter the PIN code each time the SIM is inserted.
d)
Click the Save button. If successful, the router displays the following screen:
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
29
Figure 22 - SIM security settings - SIM unlock successful
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
30
www.netcommwireless.com
Enabling/Disabling SIM PIN protection
The security PIN protection can be turned on or off using the PIN protection toggle key.
Figure 23 - PIN Settings
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
31
Changing the SIM PIN code
If you would like to change the PIN, click the Change PIN button and enter the current PIN into the Current PIN and Confirm current
PIN fields, then enter the desired PIN into the New PIN and Confirm new PIN fields and click the Save button.
Figure 24 - PIN settings - Change PIN
When the PIN has been changed successfully, the following screen is displayed:
Figure 25 - SIM security settings – PIN unlock successful
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
32
www.netcommwireless.com
Unlocking a PUK locked SIM
After three incorrect attempts at entering the PIN, the SIM card becomes PUK (Personal Unblocking Key) locked and you are
requested to enter a PUK code to unlock it.
Note: To obtain the PUK unlock code, you must contactyour service provider.
You will be issued a PUK to enable you to unlock the SIM and enter a new PIN. Enter the new PIN and PUK codes.
Click the Save button when you have finished entering the new PIN and PUK codes.
Figure 26 - SIM security - SIM PUK locked
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
33
LAN
LAN configuration
The LAN configuration page is used to configure the LAN settings of the router and to enable or disable DNS Masquerading.
Figure 27 – LAN configuration settings
The default IP of the Ethernet port is 192.168.1.1 with subnet mask 255.255.255.0. To change the IP address or Subnet mask,
enter the new IP Address and/or Subnet mask and click the Save button.
Note: If you change the IP address, remember to reboot the router and enter the new IP address into your browser address
bar.
DNS masquerading
DNS masquerading allows the router to proxy DNS requests from LAN clients to dynamically assigned DNS servers. When enabled,
clients on the router’s LAN can then use the router as a DNS server without needing to know the dynamically assigned cellular
network DNS servers.
With DNS masquerading ON, the DHCP server embedded in the NTC-30WV router hands out its own IP address (e.g. 192.168.1.1)
as the DNS server address to LAN clients. The downstream clients then send DNS requests to the NTC-30WV router which proxies
them to the upstream DNS servers.
With DNS masquerading OFF, the DHCP server hands out the upstream DNS server IP addresses to downstream clients directly,
so that downstream clients send DNS requests directly to the upstream DNS servers without being proxied by the NTC-30WV
router.
You may also override the DNS Masquerading option by specifying custom DNS Server IP addresses in the DHCP Server
configuration mentioned in the next section of this guide. In this case the DHCP server assigns downstream devices the manually
configured addresses and the DNS Masquerading option is ignored.
In most cases, it is not necessary to disable DNS masquerading but if you need to, click the DNS masquerading toggle key to turn it
OFF and then click the Save button.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
34
www.netcommwireless.com
DHCP
The DHCP page is used to adjust the settings used by the router’s built in DHPC Server which assigns IP addresses to locally
connected devices.
DHCP relay configuration
In advanced networks configurations where the NTC-30WV router should not be responsible for DHCP assignment, but instead an
existing DHCP server is located on the Wireless WAN or LAN connections, the clients behind the NTC-30WV router are able to
communicate with the DHCP server when DHCP relay is enabled. This enables the NTC-30WV router to accept client broadcast
messages and to forward them onto another subnet.
To configure the router to act as a DHCP relay agent click the DHCP relay toggle key to turn it ON and enter the DHCP server
address into the DHCP server address field. DHCP relay is disabled by default.
Figure 28 – DHCP relay configuration
DHCP configuration
You can manually set the start and end address range to be used to automatically assign addresses within, the lease time of the
assigned address, the default domain name suffix, primary and secondary DNS server, the primary and secondary WINS server, as
well as the advanced DHCP settings such as NTP, TFTP and Option 150/Option 160 (VoIP options).
Figure 29 - DHCP configuration
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
35
OPTION
DESCRIPTION
DHCP start range
Sets the first IP address of the DHCP range
DHCP end range
Sets the last IP address of the DHCP range
DHCP lease time (seconds)
The length of time in seconds that DHCP allocated IP addresses are valid
Default domain name suffix
Specifies the default domain name suffix for the DHCP clients. A domain name suffix enables users
to access a local server, for example, server1, without typing the full domain name
server1.domain.com
DNS server 1 IP address
Specifies the primary DNS (Domain Name System) server’s IP address.
DNS server 2 IP address
Specifies the secondary DNS (Domain Name System) server’s IP address.
WINS server 1 IP address
Specifies the primary WINS (Windows Internet Name Service) server IP address
WINS server 2 IP address
Specifies the secondary WINS (Windows Internet Name Service) server IP address
NTP server (Option 42)
Specifies the IP address of the NTP (Network Time Protocol) server
TFTP Server (Option 66)
Specifies the TFTP (Trivial File Transfer Protocol) server
DHCP option 150
This is used to configure Cisco IP phones. When a Cisco IP phone starts, if it is not pre-configured
with the IP address and TFTP address, it sends a request to the DHCP server to obtain this
information. Specify the string which will be sent as a reply to the option 150 request.
DHCP option 160
This is used to configure Polycom IP phones. When a Polycom IP phone starts, if it is not preconfigured with the IP address and TFTP address, it sends a request to the DHCP server to obtain
this information. Specify the string which will be sent as a reply to the option 160 request.
Enter the desired DHCP options and click the Save button.
Address reservation list
DHCP clients are dynamically assigned an IP address as they connect, but you can reserve an address for a particular device using
the address reservation list.
Figure 30 – DHCP – Address reservation list
To add a device to the address reservation list:
1.
Click the +Add button.
2.
In the Computer Name field enter a name for the device.
3.
In the MAC Address field, enter the device’s MAC address.
4.
In the IP Address fields, enter the IP address that you wish to reserve for the device.
5.
If the Enable toggle key is not set to ON, click it to switch it to the ON position.
6.
Click the Save button to save the settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
36
www.netcommwireless.com
Dynamic DHCP client list
The Dynamic DHCP client list displays a list of the DHCP clients. If you want to reserve the current IP address for future use, click
the Clone button and the details will be copied to the address reservation list fields. Remember to click the Save button under the
Address reservation list section to confirm the configuration.
Figure 31 - Dynamic DHCP client list
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
37
Wireless Settings
The Wireless Settings pages allow you to configure the WiFi settings of the router.
Basic
The basic page provides options for turning WiFi on or off, modes of operation, frequency and security settings.
Figure 32 - Wireless Settings - Basic
OPTION
DEFINITION
Radio On/Off
WiFi is turned on by default. Changing this option to OFF will turn OFF the wireless functionality on the NTC-30WV and you will not
be able to connect wirelessly.
Country
Select the country you are operating the NTC-30WV in.
There are 6 possible network modes to use depending on the capability of your devices’ wireless network cards. Each mode
represents one or more wireless network protocols. Each wireless device will be capable of receiving some but possibly not all of
wireless broadcast protocol types. They are:
Network Mode





802.11b/g/n mixed mode.
802.11b only.
802.11g only.
802.11n only.
802.11b/g/n mixed mode.
Frequency (Channel)
Select the wireless channel that the wireless signal will broadcast on.
SSID
The SSID (Service Set IDentifier or Network Name) in use for the wireless network.
Broadcast SSID
Toggles whether the router broadcasts the SSID or whether it is hidden from wireless network scans.
Network Authentication
The wireless security settings. See below for in depth analysis.
WPA Pre-Shared Key
The wireless security key or wireless password.
WPA Group Rekey Interval
The time in seconds before a new key is generated.
WPA Encryption
The type of WPA encryption. Options include AES, TKIP or TKIP + AES.
Table 16 - Wireless Configuration - Basic Configuration Items
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
38
www.netcommwireless.com
Advanced
The advanced wireless configuration page allows you to modify advanced wireless settings of your router. These settings are set to
optimal settings for most situations and should not be changed unless you are aware of the effect that your changes will have.
Figure 33 - Wireless Settings - Advanced
OPTION
DEFINITION
BG Protection Mode
A protection designed to prevent collisions among 802.11b/g modes. Mode options include Auto, On, or Off.
Client Ide Timeout
The time in seconds that a wireless client session can be idle before the router cancels the session and
defines the wireless client as not connected.
Beacon Interval
Interval of time in which the wireless router broadcasts a beacon which is used to synchronize the wireless
network.
Data Beacon Rate (DTIM)
Enter a value in milliseconds between 1 and 255 for the Delivery Traffic Indication Message (DTIM). A DTIM is
a countdown informing clients of the next window for listening to broadcast and multicast messages.
Fragment Threshold
This specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this
value too low, it will result in bad performance.
RTS Threshold
When the packet size is smaller than the RTS threshold, the wireless router will not use the RTS/CTS
mechanism to send this packet.
TX Power
This determines the transmitting or output power of the antenna.
Short Preamble
www.netcommwireless.com
Enable or disable short preambles in use on the wireless network. Using short preambles should improve
throughput, however some wireless network adapters must use long preambles.
Table 17 - Wireless Settings - Advanced Configuration Items
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
39
Wireless Distribution System (WDS)
The NTC-30WV supports the configuration of a Wireless Distribution System (WDS). WDS allows you to expand your wireless
network with multiple access points. There are two WDS modes available: Bridge Mode and Repeater Mode.
In Bridge mode, the WDS access points communicate with each other but do not communicate with wireless clients. Bridge mode
is best used in situations where the client machines connect via Ethernet cable. In Repeater mode, the WDS access points
communicate with each other and with wireless clients.
Below is an example of how to configure two NTC-30WV routers to use the Repeater mode WDS feature. In this example, Access
Point 1 is connected to a mobile broadband network and Access Point 2 and its clients will connect to the internet through Access
Point 1.
Access Point 1 – Mobile Broadband Connected
1.
Establish a Mobile Broadband connection with Access Point 1:
Figure 34 - WDS - Access Point 1 Status
2.
Configure the LAN IP Address of Access Point 1. In this example, it is set to the default address of 192.168.1.1:
Figure 35 - WDS - Access Point 1 LAN IP Setup
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
40
www.netcommwireless.com
3.
Enable the DHCP Server on Access Point 1:
Figure 36 - WDS - Access Point 1 DHCP Server Settings
4.
Click Wireless Settings and then Basic. Enter the required details as listed in the table below:
Figure 37 – WDS - Access Point 1 Repeater Mode Setup
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
41
5.
Click WDS and set WDS Mode to Repeater Mode. Enter an Encryption key and in the AP Mac Address1 field, type the
MAC address of Access Point 2.
Figure 38 – WDS - Access Point 1 WDS Settings
When you have entered the required information, click Save:
Access Point 2 – No connection to mobile broadband
1.
Access Point 2 will act as a repeater for and provide internet access to its clients through Access Point 1 and therefore
does not require a Mobile Broadband connection to be established.
Figure 39 – WDS - Aceess Point 2 Status
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
42
www.netcommwireless.com
2.
Configure the LAN IP Address of Access Point 2. In this example, it is set to the default address of 192.168.1.2:
Figure 40 - WDS - Access Point 2 LAN IP Setup
3.
Set the DHCP Server on Access Point 2 to Disable:
Figure 41 - WDS - Access Point 2 DHCP Settings
4.
Under Wireless Setup, select the same frequency channel as you did for Access Point 1. Enter an SSID to identify Access
Point 2. Copy the Network Authentication and Encryption settings from Access Point 1. Set Access Point 2 to Repeater
mode and enter the MAC address of Access Point 1 in the AP MAC Address1 field. The MAC address of Access Point 1 is
listed on the same page under Wireless Settings > Basic under the Wireless Distribution System (WDS) section. When you
have entered the required information, click Save:
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
43
Figure 42 - WDS – Access Point 2 Repeater Mode Setup
The Wireless Distribution System setup is now complete.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
44
www.netcommwireless.com
MAC Filtering
The Wireless LAN MAC filter feature ensures the network accessibility for the wireless client devices can be controlled. When the
MAC filter is enabled with an Allow policy only those wireless clients whose MAC address is listed in the MAC filter list will be able to
gain network access. All other wireless client devices will be denied network access. When the MAC filter is enabled with a Reject
policy all wireless client devices listed whose MAC address is listed in the MAC filter list will be denied network access. All other
wireless client devices will be allowed network access.
Figure 43 - MAC Filtering
Station Info
The Station Info page shows the number of devices currently connected to your NTC-30WV via Wireless. The MAC address, Host
Name and IP address of these devices are displayed.
Figure 44 - Wireless Station List
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
45
Routing
Static
Static routing is the alternative to dynamic routing used in more complex network scenarios and is used to facilitate communication
between devices on different networks. Static routing involves configuring the routers in your network with all the information
necessary to allow the packets to be forwarded to the correct destination. If you change the IP address of one of the devices in the
static route, the route will be broken.
Figure 45 - Static routing list
Some routes are added by default by the router on initialization such as the Ethernet subnet route for routing to a device on the
Ethernet subnet.
Adding Static Routes
To add a new route to the static routing list, click the +Add button. The Static routes page appears.
1.
In the Route name field, type a name for the route so that it can be identified in the static routing list.
2.
From the Network interface drop down list, select the interface for which you would like to create a static route.
3.
In the Destination IP address field, enter the IP address of the destination of the route.
4.
In the IP subnet mask field, enter the subnet mask of the route.
5.
In the Gateway IP address field, enter the IP address of the gateway that will facilitate the route.
6.
In the Metric field enter the metric for the route. The metric value is used by the router to prioritise routes. The lower the
value, the higher the priority. To give the route the highest priority, set it to 0.
7.
Click the Save button to save your settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
46
www.netcommwireless.com
Figure 46 - Adding a static route
Active routing list
Static routes are displayed in the Active routing list.
Figure 47 - Active routing list
Deleting static routes
From the static routing list, click the
icon to the right of the entry you wish to delete.
Figure 48 - Deleting a static route
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
47
RIP
RIP (Routing Information Protocol) is used for advertising routes to other routers. Thus all the routes in the router’s routing table will
be advertised to other nearby routers. For example, the route for the router’s Ethernet subnet could be advertised to a router on the
PPP interface side so that a router on this network will know how to route to a device on the router’s Ethernet subnet. Static routes
must be added manually according to your requirements. See Adding Static Routes.
Note: Some routers will ignore RIP.
Figure 49 - RIP configuration
To enable Routing Information Protocol (RIP)
1.
Click the RIP toggle key to switch it to the ON position.
2.
Using the Version drop down list, select the version of RIP that you would like to use.
3.
Select the interface for which you want RIP to apply. You can choose the LAN interface, the WWAN interface or BOTH.
4.
Click the Save button to confirm your settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
48
www.netcommwireless.com
Redundancy (VRRP) configuration
Virtual Router Redundancy Protocol (VRRP) is a non-proprietary redundancy protocol designed to increase the availability of the
default gateway servicing hosts on the same subnet. This increased reliability is achieved by advertising a “virtual router” (an
abstract representation of master and backup routers acting as a group) as a default gateway to the host(s) instead of one physical
router. Two or more physical routers are then configured to stand for the virtual router, with only one doing the actual routing at any
given time. If the current physical router that is routing the data on behalf of the virtual router fails, an arrangement is made for
another physical router to automatically replace it. The physical router that is currently forwarding data on behalf of the virtual router
is called the master router.
Master routers have a priority of 255 and backup router(s) can have a priority between 1 and 254.
A virtual router must use 00-00-5E-00-01-XX as its (MAC) address. The last byte of the address (XX) is the Virtual Router Identifier
(VRID), which is different for each virtual router in the network. This address is used by only one physical router at a time, and is the
only way that other physical routers can identify the master router within a virtual router.
Figure 50 - VRRP configuration
To configure VRRP, configure multiple devices as follows and connect them all via an Ethernet network switch to downstream
devices.
1.
Click the Redundancy (VRRP) toggle key to activate VRRP.
2.
In the Virtual ID field, enter an ID between 1 and 255. This is the VRRP ID which is different for each virtual router on the
network.
3.
In the Router priority field, enter a value for the priority – a higher value is a higher priority.
4.
The Virtual IP address field is used to specify the VRRP IP address – this is the virtual IP address that both virtual routers
share.
5.
Click the Save button to save the new settings.
Note: Configuring VRRP changes the MAC address of the Ethernet port and therefore if you want to resume with the web
configuration you must use the new IP address (VRRP IP) or on a command prompt type:
arp –d <ip address> (i.e. arp –d 192.168.1.1) to clear the arp cache.(old MAC address).
Note: For more detail on configuring VRRP, please visit the product page on the NetComm Wireless website at
http://support.netcommwireless.com/product/m2m-wireless-series/ntc-30wv and click on FAQs/Self Help.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
49
Port Forwarding
The Port forwarding list is used to configure the Network Address Translation (NAT) rules currently in effect on the router.
Figure 51 – Port forwarding list
The purpose of the port forwarding feature is to allow mapping of inbound requests to a specific port on the WAN IP address to a
device connected on the Ethernet interface.
Adding a port forwarding rule
To create a new port forwarding rule:
1.
Click the +Add button. The port forwarding settings screen is displayed.
2.
Use the Protocol drop down list to select the type of protocol you want to use for the rule. The protocols selections
available are TCP, UDP and All.
3.
In the Source IP Address field, enter a “friendly” address that is allowed to access the router or a wildcard IP address
(0.0.0.0) that allows all IP addresses to access the router.
4.
The Source Port Range (From) and (To) fields are used to specify the port(s) on the source side that are to be forwarded.
This allows you to send a range of consecutive port numbers by entering the first in the range in the (From) field and the
last in the range in the (To) field. To forward a single port, enter the port in the (From) field and repeat it in the (To) field.
5.
In the Destination network address field, enter the IP address of the client to which the traffic should be forwarded.
6.
The Destination Port Range (From) and (To) fields are used to specify the port(s) on the destination side that are to be
forwarded. If the Source port range specifies a single port then the destination port may be configured to any port. If the
Source port range specifies a range of port numbers then the Destination port range must be the same as the Source port
range.
7.
Click the Save button to confirm your settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
50
www.netcommwireless.com
Figure 52 - Port forwarding settings
To delete a port forwarding rule, click the
delete.
www.netcommwireless.com
button on the Port forwarding list for the corresponding rule that you would like to
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
51
DMZ
The Demilitarized Zone (DMZ) allows you to configure all incoming traffic on all protocols to be forwarded to a selected device
behind the router. This feature can be used to avoid complex port forwarding rules, but it exposes the device to untrusted networks
as there is no filtering of what traffic is allowed and what is denied.
The DMZ configuration page is used to specify the IP Address of the device to use as the DMZ host.
Figure 53 - DMZ configuration
1.
Click the DMZ toggle key to turn the DMZ function ON.
2.
Enter the IP Address of the device to be the DMZ host into the DMZ IP Address field.
3.
Click the Save button to save your settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
52
www.netcommwireless.com
Router firewall
The Router firewall page is used to enable or disable the in-built firewall on the router. When enabled, the firewall performs stateful
packet inspection on inbound traffic from the wireless WAN and blocks all unknown services, that is, all services not listed on the
Services configuration page of the router.
With respect to the other Routing options on the Networking page, the firewall takes a low priority. The priority of the firewall can be
described as:
DMZ > MAC/IP/Port filtering rules > MAC/IP/Port filtering default rule > Router firewall rules
In other words, the firewall is of the lowest priority when compared to other manual routing configurations. Therefore, a MAC/IP/Port
filtering rule takes priority in the event that there is a conflict of rules. When DMZ is enabled, MAC/IP/Port filtering rules and the
router firewall are ignored but the router will still honour the configuration of the Remote router access control settings listed under
Administration Settings.
Figure 54 - Router firewall toggle key
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
53
MAC / IP / Port filtering
The MAC/IP/Port filter feature allows you apply a policy to the traffic that passes through the router, both inbound and outbound, so
that network access can be controlled. When the filter is enabled with a default rule of “Accepted”, all connections will be allowed
except those listed in the “Current MAC / IP / Port filtering rules in effect” list. Conversely, when the default rule is set to “Dropped”,
all connections are denied except for those listed in the filtering rules list.
Figure 55 - MAC / IP / Port filtering
Note: When enabling MAC / IP / Port filtering and setting the default rule to “Dropped”, you should ensure that you have
first added a filtering rule which allows at least one known MAC/IP to access the router, otherwise you will not be able to
access the user interface of the router without resetting the router to factory default settings.
Creating a MAC / IP / Port filtering rule
To create a filtering rule:
1.
Click the MAC / IP / Port filtering toggle key to switch it to the ON position.
2.
Using the Default rule (inbound/forward) drop down list, select the default action for the router to take when traffic reaches
it. By default, this is configured to Accepted. If you change this to Dropped, you should first configure a filter rule that
allows at least one device access to the router, otherwise you will effectively be locked out of the router.
3.
Click the Save button to confirm the default rule.
4.
In the Current MAC / IP / Port filtering rules in system section, click the +Add button.
Figure 56 - Current MAC / IP/ Port filtering rules in effect
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
54
www.netcommwireless.com
5.
Enter the details of the rule in the section that is displayed and click the Save button.
Figure 57 - MAC / IP / Port filtering settings
OPTION
DESCRIPTION
Bound
Use the drop down list to select the direction of the traffic for which you want to apply to the rule.
Inbound refers to all traffic that is entering the router including data entering from the WAN and the
LAN. Outbound refers to all traffic exiting the router including traffic leaving in the direction of the
WAN and traffic leaving in the direction of the LAN. Forward specifies traffic that enters on the LAN or
WAN side and is forwarded to the opposite end.
Protocol
Use the drop down list to select the protocol for the rule. You can have the rule apply to All
protocols, TCP, UDP, UDP/TCP or ICMP.
Source MAC Address
Enter the MAC address in six groups of two hexadecimal digits separated by colons (:). e.g.
00:40:F4:CE:FA:1E
Source IP Address
Enter the IPv4 address that the traffic originates from and the subnet mask using CIDR notation.
Destination IP Address
Enter the IPv4 address that the traffic is destined for and the subnet mask using CIDR notation.
Action
Select the action to take for traffic which meets the above criteria. You can choose to Accept or Drop
packets. When the default rule is set to Accept, you cannot create a rule with an Accept action since
the rule is redundant. Likewise, if the default rule is set to Dropped you cannot create a rule with a
Drop action.
Comment
[Optional] Use this field to enter a comment as a meaningful description of the rule.
Table 18 - Current MAC / IP / Port filtering rules in effect
6.
The new rule is displayed in the filtering rules list. You can edit the rule by clicking the
clicking the
Edit button or delete the rule by
button.
Figure 58 - Completed filtering rule
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
55
VPN
A Virtual Private Network (VPN) is a tunnel providing a private link between two networks or devices over a public network. Data to
be sent via a VPN needs to be encapsulated and as such is generally not visible to the public network.
The advantages of a VPN connection include:
Data Protection
Access Control
Data Origin Authentication
Data Integrity
Each VPN connection has different configuration requirements. The following pages detail the configuration options available for the
different VPN connection types.
Note: The following descriptions are an overview of the various VPN options available. More detailed instructions are
available in separate whitepapers on the NetComm Wireless website.
IPSec
IPSec operates on Layer 3 of the OSI model and as such can protect higher layered protocols. IPSec is used for both site to site
VPN and Remote Access VPN. The NTC-30WV router supports IPsec end points and can be configured with Site to Site VPN
tunnels with third party VPN routers.
Configuring an IPSec VPN
From the menu at the top of the screen, click Networking and under the VPN section, click IPSec. A list of configured IPSec VPN
connections is displayed.
Figure 59 - IPSec VPN List
Click the +Add button to begin configuring an IPSec VPN connection.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
56
www.netcommwireless.com
Figure 60 – IPSec profile edit
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
57
The following table describes each of the fields of the IPSec VPN Connection Settings page.
ITEM
DEFINITION
IPSec profile
Enables or disables the VPN profile.
Profile name
A name used to identify the VPN connection profile.
Remote IPSec address
The IP address or domain name of the IPSec server.
Remote LAN address
Enter the IP address of the remote network for use on the VPN connection.
Remote LAN subnet mask
Enter the subnet mask in use on the remote network.
Local LAN address
Enter the IP address of the local network for use on the VPN connection.
Local LAN subnet mask
Enter the subnet mask in use on the local network.
Encapsulation type
Select the encapsulation protocol to use with the VPN connection. You can choose ESP, AH or Any.
IKE mode
Select the IKE mode to use with the VPN connection. You can choose Main, Aggressive or Any.
PFS
Choose whether Perfect Forward Secrecy is ON or OFF for the VPN connection.
IKE encryption
Select the cipher type to use for the Internet Key Exchange.
IKE hash
Select the IKE Hash type to use for the VPN connection. The hash is used for authentication of packets for the key
exchange.
IPSec encryption
Select the IPSec encryption type to use with the VPN connection.
IPSec hash
Select the IPSec hash type to use for the VPN connection. The hash is used for authentication of packets for the VPN
connection.
DH group
Select the desired Diffie-Hellman group to use. Higher groups are more secure but also require longer to generate a key.
DPD action
Select the desired Dead Peer Detection action. This is the action to take when a dead Internet Key Exchange Peer is
detected.
DPD keep alive time
Enter the time in seconds for the interval between Dead Peer Detection keep alive messages.
DPD timeout
Enter the time in seconds of no response from a peer before Dead Peer Detection times out.
IKE re-key time
Enter the time in seconds between changes of the encryption key. To disable changing the key, set this to 0.
SA life time
Enter the time in seconds for the security association lifetime.
Select the type of key mode in use for the VPN connection. You can select from:
Key mode



Pre Shared Key
RSA keys
Certificates
Pre-shared key
The pre-shared key is the key that peers used to authenticate each other for Internet Key Exchange.
Remote ID
Specifies the domain name of the remote network.
Local ID
Specifies the domain name of the local network.
Update Time
Displays the last time the key was updated.
Local RSA Key Upload
Select the RSA key file for the local router here by clicking the Browse button.
Remote RSA Key Upload
Select the RSA key file for the remote router here by clicking the Browse button.
Private key Passphrase
The Private key passphrase of the router is the passphrase used when generating the router’s private key using
OpenSSL CA.
Key / Certificate
Select the type of key or certificate to use for authentication. You can select Local private key, Local public certificate,
Remote public certificate, CA certificate, CRL certificate.
IPSec Certificate Upload
Select the IPSec certificate to upload by clicking the Browse button.
Table 19 - IPSec Configuration Items
Note: For more detail on configuring IPSec, please visit the product page on the NetComm Wireless website at
http://support.netcommwireless.com/product/m2m-wireless-series/ntc-30wv and click on FAQs/Self Help.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
58
www.netcommwireless.com
OpenVPN
OpenVPN is an open source virtual private network (VPN) program for creating point-to-point or server-to-multi-client encrypted
tunnels between host computers. It can traverse network address translation (NAT) and firewalls and allows authentication by
certificate, pre-shared key or username and password. OpenVPN works well through proxy servers and can run over TCP and UDP
transports. Support for OpenVPN is available on several operating systems, including Windows, Linux, Mac OS, Solaris, OpenBSD,
FreeBSD, NetBSD and QNX.
Note: For more detail on configuring OpenVPN, please visit the product page on the NetComm Wireless website at
http://support.netcommwireless.com/product/m2m-wireless-series/ntc-30wv and click on FAQs/Self Help.
Configuring an Open VPN server
From the menu at the top of the screen, click Networking and from the VPN section on the left, click OpenVPN. A list of configured
OpenVPN VPN connections is displayed.
Figure 61 - OpenVPN VPN List
Click the +Add button for the type of OpenVPN server/client you would like to configure.
OpenVPN Server
To configure an OpenVPN Server:
1.
Click the OpenVPN profile toggle key to switch it to the ON position.
2.
Type a name for the OpenVPN server profile you are creating.
3.
Select OpenVPN connection type (TUN/TAP). Default is TUN.
4.
Use the Server port field to select a port number and then use the drop down list to select a packet type to use for your
OpenVPN Server. The default OpenVPN port is 1194 and default packet type is UDP.
5.
In the VPN network address and VPN network subnet mask fields, enter the IP address and network subnet mask to
assign to your VPN. This is ideally an internal IP address which differs from your existing address scheme.
6.
Next to Diffie-Hellman parameters, select appropriate encryption key size then click the Generate DH button. This will
create an encryption key to secure your OpenVPN connection. Default key size is (1024) bit.
7.
Under Server Certificates, enter the required details. All fields must be completed. The Country field must consist of two
characters only. When the details have been entered, click the Generate CA certificate button to generate the Certificate
Authority (CA) certificate based on this information.
8.
Under the Server certificates section, select the Authentication type that you would like to use for the OpenVPN Server.
Note: The Diffie-Hellman parameters can take up to 10 minutes to generate. Please be patient.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
59
Certificate Authentication
In the Certificate Management section, enter the required details to create a client certificate. All fields are required. When you have
finished entering the details, click the Generate button.
Figure 62 - OpenVPN server configuration – Certificate management
When it is done, you can click the Download P12 button or the Download TGZ button to save the certificate file depending on
which format you would like. If for some reason the integrity of your network has been compromised, you can return to this screen
and use the Certificate drop down list to select the certificate and then press the Revoke button to disable it.
Optional: To inform the OpenVPN server of the network address scheme of the currently selected certificate, enter the network
address and network subnet mask in the respective fields and click the Set network information button. If you do not enter the
remote subnet here, any packet requests from the server to the client will not be received by the client network because it is not
aware of the remote client’s subnet.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
60
www.netcommwireless.com
Figure 63 – OpenVPN server profile settings
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
61
Username / Password Authentication
In the Username/Password section, enter the username and password you would like to use for authentication on the OpenVPN
Server. Click the Download CA certificate or Download CA TGZ depending on file format button to save the ca.crt file. This file will
need to be provided to the client.
Note: If you wish to have more than one client connect to this OpenVPN server, you must use Certificate authentication
mode as Username/Password only allows for a single client connection.
Figure 64 - OpenVPN Server – Username / Password section
Optional: To inform the OpenVPN server of the network address scheme of the currently selected certificate, enter the network
address and network subnet mask in the respective fields and click the Set Network Information button. If you do not enter the
remote subnet here, any packet requests from the server to the client will not be received by the client network because it is not
aware of the remote client’s subnet.
When you have finished entering all the required information, click Save to finish configuring the OpenVPN server.
Configuring an OpenVPN Client
1.
Click the OpenVPN profile toggle key to switch it to the ON position.
2.
In the Profile name field, type a name for the OpenVPN client profile you are creating.
3.
In the Server IP address field, type the WAN IP address /host domain name of the OpenVPN server.
4.
Select OpenVPN connection type (TUN/TAP). Default is TUN.
5.
Use the Server port field to select a port number and then use the drop down list to select a packet type to use for the
OpenVPN server. The default OpenVPN port is 1194 and default packet type is UDP.
6.
If the Default gateway option is applied on the OpenVPN client page, the OpenVPN server will enable connections to be
made to other client networks connected to it. If it is not selected, the OpenVPN connection allows for secure
communication links between this router and the remote OpenVPN server only.
7.
Use the Authentication type options to select the Authentication type that you would like to use for the OpenVPN client.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
62
www.netcommwireless.com
Certificate Authentication
In the Certificate upload section at the bottom of the screen, click the Browse button and locate the certificate file you downloaded
when you configured the OpenVPN server. When it has been selected, click the Upload button to send it to the router.
Figure 65 - OpenVPN client - Certificate upload
Username / Password Authentication
Enter the username and password to authenticate with the OpenVPN server.
Figure 66 - OpenVPN Client - Username/Password section
Use the Browse button to locate the CA certificate file you saved from the OpenVPN Server and then press the Upload button to
send it to the router.
Click the Save button to complete the OpenVPN Client configuration.
Configuring an OpenVPN P2P Connection
To configure an OpenVPN peer-to-peer connection:
1.
Set the OpenVPN profile toggle key to switch it to the ON position.
2.
In the Profile name field, type a name for the OpenVPN P2P profile you are creating.
3.
On the router designated as the server, leave the Server IP address field empty. On the router designated as the client,
enter the WAN IP address/host domain name of the server.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
63
Figure 67 - OpenVPN P2P mode settings
4.
Use the Server port field to select a port number and then use the drop down list to select a packet type to use for the
OpenVPN server. The default OpenVPN port is 1194 and default packet type is UDP.
5.
In the Local IP Address and Remote IP Address fields, enter the respective local and remote IP addresses to use for the
OpenVPN tunnel. The slave should have the reverse settings of the master.
6.
Under the Remote network section, enter the network Address and network Subnet mask. The Network Address and
Network Mask fields inform the Master node of the LAN address scheme of the slave.
7.
Press the Generate button to create a secret key to be shared with the slave. When the timestamp appears, you can click
the Download button to save the file to exchange with the other router.
8.
When you have saved the secret key file on each router, use the Browse button to locate the secret key file for the master
and then press the Upload button to send it to the slave. Perform the same for the other router, uploading the slave’s
secret key file to master.
9.
When they are uploaded click the Save button to complete the peer-to-peer OpenVPN configuration.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
64
www.netcommwireless.com
PPTP-Client
The Point-to-Point Tunnelling Protocol (PPTP) is a method for implementing virtual private networks using a TCP and GRE tunnel to
encapsulate PPP packets. PPTP operates on Layer 2 of the OSI model and is included on Windows computers.
Configuring the PPTP Client
To configure the PPTP client:
1.
From the menu bar at the top of the screen, click Networking and then from the VPN section on the left side of the screen,
click PPTP client. The PPTP client list is displayed.
Figure 68 - PPTP client list
2.
Click the +Add button to begin configuring a new PPTP client profile. The PPTP client edit screen is displayed.
Figure 69 - VPN PPTP client edit
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
65
3.
Click the Enable PPTP client toggle key to switch it to the ON position.
4.
In the Profile name list, enter a profile name for the tunnel. This may be anything you like and is used to identify the tunnel
on the router.
5.
Use the Username and Password fields to enter the username and password for the PPTP account.
6.
In the PPTP server address field, enter the IP address /host domain name of the PPTP server.
7.
From the Authentication type drop down list, select the Authentication type used on the server. If you do not know the
authentication method used, select any and the router will attempt to determine the correct authentication type for you.
There are 5 authentication types you can choose from:
CHAP – uses a three way handshake to authenticate the identity of a client.
MS-CHAP v1 – This is the Microsoft implementation of the Challenge Handshake Authentication Protocol for which
support was dropped in Windows® Vista.
MS-CHAP v2 - This is the Microsoft implementation of the Challenge Handshake Authentication Protocol which was
introduced in Windows® NT 4.0 and is still supported today.
PAP – The Password Authentication Protocol uses a password as a means of authentication and as such, is
commonly supported. PAP is not recommended because it transmits passwords unencrypted and is not secure.
EAP – Extensible Authentication Protocol. An Authentication protocol commonly used in wireless networks.
8.
The metric value helps the router to prioritise routes and must be a number between 0 and 65535. The default value is 30
and should not be modified unless you are aware of the effect your changes will have.
9.
The Use peer DNS option allows you to select whether the remote clients will use the Domain Name Server of the PPTP
server. Click the toggle key to set this to ON or OFF as required.
10. NAT masquerading allows the router to modify the packets sent and received to inform remote computers on the internet
that packets originating from a machine behind the router actually originated from the WAN IP address of the router’s
internal NAT IP address. Click the toggle key to switch this to the ON position if you want to use this feature.
11. Set default route to PPTP sets all outbound data packets to go out through the PPTP tunnel. Click the toggle key to
switch this to the ON position if you want to use this feature.
12. The Verbose logging option sets the router to output detailed logs regarding the PPTP connection in the System Log
section of the router interface.
13. The Reconnect delay is the time in seconds that the router will wait before attempting to connect to the PPTP server in the
event that the connection is broken. The minimum time to wait is 30 seconds so as to not flood the PPTP server with
connection requests, while the maximum time to wait is 65335 seconds.
14. The Reconnect retries is the number of connection attempts that the router will make in the event that the PPTP
connection goes down. If set to 0, the router will retry the connection indefinitely, otherwise the maximum number of times
to retry cannot be greater than 65335.
15. Click the Save button to save the changes. The VPN will attempt to connect after your click Save. Click the Status button
at the top left of the interface to return to the status window and monitor the VPN’s connection state.
Note: For more detail on configuring PPTP Client, please visit the product page on the NetComm Wireless website at
http://support.netcommwireless.com/product/m2m-wireless-series/ntc-30wv and click on FAQs/Self Help.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
66
www.netcommwireless.com
GRE tunnelling
The Generic Route Encapsulation (GRE) protocol is used in addition to Point-to-Point Tunnelling Protocol (PPTP) to create VPNs
(virtual private networks) between clients and servers or between clients only. Once a PPTP control session establishes the VPN
tunnel GRE is used to securely encapsulate the data or payload.
Configuring GRE tunnelling
To configure GRE tunnelling:
1.
From the menu bar at the top of the screen, click Networking and then from the VPN section on the left side of the screen,
click GRE. The GRE client list is displayed.
Figure 70 - GRE client list
2.
Click the +Add button to begin configuring a new GRE tunnelling client profile. The GRE Client Edit screen is displayed.
Figure 71 – GRE client edit
3.
Click the Enable GRE Tunnel toggle key to switch it to the ON position.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
67
4.
In the Profile name, enter a profile name for the tunnel. This may be anything you like and is used to identify the tunnel on
the router.
5.
In the GRE server address field, enter the IP address or domain name of the GRE server.
6.
In the Local tunnel address field, enter the IP address you want to assign the tunnel locally.
7.
In the Remote tunnel address field, enter the IP address you want to assign to the remote tunnel.
8.
In the Remote network address field, enter the IP address scheme of the remote network.
9.
In the Remote network subnetmask field, enter the subnet mask of the remote network.
10. The TTL (Time To Live) field is an 8-bit field used to remove an undeliverable data packet from a network to avoid
unnecessary network traffic across the internet. The default value of 255 is the upper limit on the time that an IP datagram
can exist. The value is reduced by at least one for each hop the data packet takes to the next router on the route to the
datagram’s destination. If the TTL field reaches zero before the datagram arrives at its destination the data packet is
discarded and an error message is sent back to the sender.
11. The Verbose logging option sets the router to output detailed logs regarding the GRE tunnel in the System Log section of
the router interface.
12. The Reconnect delay is the time in seconds that the router will wait before attempting to connect to the GRE server in the
event that the connection is broken. The minimum time to wait is 30 seconds so as to not flood the GRE server with
connection requests, while the maximum time to wait is 65335 seconds.
13. The Reconnect retries is the number of connection attempts that the router will make in the event that the GRE connection
goes down. If set to 0, the router will retry the connection indefinitely, otherwise the maximum number of times to retry
cannot be greater than 65335.
14. Click the Save button to save the changes. The VPN will attempt to connect after your click Save. Click the Status button
at the top left of the interface to return to the status window and monitor the VPN’s connection state.
Note: For more detail on configuring GRE, please visit the product page on the NetComm Wireless website at
http://support.netcommwireless.com/product/m2m-wireless-series/ntc-30wv and click on FAQs/Self Help.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
68
www.netcommwireless.com
Services
Dynamic DNS
The DDNS page is used to configure the Dynamic DNS feature of the router. A number of Dynamic DNS hosts are available from
which to select.
Figure 72 – Dynamic DNS settings
Dynamic DNS provides a method for the router to update an external name server with the current WAN IP address.
To configure dynamic DNS:
1.
Click the DDNS configuration toggle key to switch it to the ON position.
2.
From the Dynamic DNS drop down list, select the Dynamic DNS service that you wish to use. The available DDNS services
available are:

www.dhs.org

www.dyndns.org

www.dyns.cx

www.easydns.com

www.justlinux.com

www.ods.org

www.tzo.com

www.zoneedit.com
3.
Enter your hostname in ‘Host name’ field.
4.
In the Username and Password fields, enter the logon credentials for your DDNS account. Enter the password for the
account again in the Verify password field.
5.
Click the Save button to save the DDNS configuration settings.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
69
Network time (NTP)
The NTP (Network Time Protocol) settings page allows you to configure the NTC-30WV router to synchronize its internal clock with
a global Internet Time server and specify the time zone for the location of the router. This provides an accurate timekeeping function
for features such as System Log entries and Firewall settings where the current system time is displayed and recorded.
Any NTP server available publicly on the internet may be used. The default NTP server is 0.netcomm.pool.ntp.org.
Figure 73 - NTP settings
Configuring Timezone settings
To configure time zone settings:
1.
The Current time field shows the time and date configured on the router. If this is not accurate, use the Time zone drop
down list to select the correct time zone for the router. If the selected zone observes daylight savings time, a Daylight
savings time schedule link appears below the drop down list. Click the link to see the start and end times for daylight
savings.
2.
When you have selected the correct time zone, click the Save button to save the settings.
Configuring NTP settings
To configure NTP settings:
1.
Click the Network time (NTP) toggle key to switch it to the ON position.
2.
In the NTP service field, enter the address of the NTP server you wish to use.
3.
The Synchronization on WWAN connection toggle key enables or disables the router from performing a synchronization of
the time each time a mobile broadband connection is established.
4.
The Daily synchronisation toggle key enables or disables the router from performing a synchronization of the time each
day.
5.
When you have finished configuring NTP settings, click the Save button to save the settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
70
www.netcommwireless.com
Data stream manager
The data stream manager provides you with the ability to create mappings between input ports and output ports (e.g. Serial Port,
SMS, GPS) and performs any required translation or data processing by each virtual data tunnel. Customers interested in
developing their own applications to create custom mappings can contact NetComm Wireless about our Software Development Kit.
The data stream manager provides a wide range of possibilities and expands upon simple PAD functionality to include the
forwarding and translation of data between any of the input and output ports of the router. For example, you could send the GPS
data received by the module (in NMEA format) through a serial port (by means of a USB-to-Serial cable). In each case, the logical
flow of data is from Endpoint A to Endpoint B.
Creating a new data stream
To create a new stream:
1.
Click the +Add button on the right side of the page.
Figure 74 - Data stream list
1.
Click the Activate toggle key so that it is in the ON position.
2.
In the Data stream name field, enter a name to identify the mapping on the Data stream list.
3.
Under the Endpoint A section, use the Type drop down list to select the desired input port, for example Serial, SMS
messaging or GPS. Use the Mode drop down list to select the input port’s mode of operation. Some endpoint types and
modes may result in extra options being displayed below Endpoint A. Use the drop down lists to select the correct
parameters for the input port.
4.
Under the Endpoint B section, use the Type drop down list to select the desired output port, for example Serial, IP, or
SMS messaging. Use the Mode drop down list to select the output port’s mode of operation. Some endpoint types and
modes may result in extra options being displayed below Endpoint B. Use the drop down lists to select the correct
parameters for the output port.
5.
Click the Save button to confirm your settings and create the new data stream. The new data stream appears in the Data
stream list.
Figure 75 - Activate button
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
71
Figure 76 – Data stream list
Below are some configuration examples of how the Data stream manager can be used.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
72
www.netcommwireless.com
Sending Serial data to an IP network
This example demonstrates common settings for sending raw traffic out of an attached USB-to-Serial cable to a TCP/IP server
running on the router.
Figure 77 - Data stream manager – Serial to IP example
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
73
Sending an incoming SMS to an IP network
This example shows a configuration allowing received SMS messages to be forwarded to a TCP client running on the router which
sends the SMS message to TCP server 123.45.67.89 on port 2000.
Figure 78 - Data stream manager – SMS to IP example
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
74
www.netcommwireless.com
Watchdogs
To access the Watchdogs page, click the Services menu item, then select the Watchdogs menu item on the left.
Figure 79 - Watchdogs Settings
Watchdogs are features which monitor the router for anomalies and restart the router if an anomaly occurs preventing its normal
operation. When configured, the watchdogs feature transmits controlled ping packets to 1 or 2 user specified IP addresses to
confirm an active connection. If the watchdog does not receive responses to the pings after a specified number of failures, it will
reboot the device in a last resort attempt to restore connectivity.
We recommend using caution when implementing this feature in situations where the device is intentionally offline for a particular
reason, for example, when Connect-on-demand has been enabled. This is because the watchdog expects to be able to access the
internet at all times, and will always eventually reboot the router if access isn't restored by the time the various timers expire and the
fail count is reached.
It is due to the nature of the watchdog being a last resort standalone backup mechanism that it will continue to do its job and
reboot the device even when the Connect-on-demand session is idle, or the PDP context is disabled by the user. Therefore, we
recommended that you disable this feature if Connect-on-demand is configured or if the PDP context is intentionally disconnected
on occasion.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
75
The watchdog works as follows:
a)
The router sends 3 consecutive pings to the first destination address at the interval specified in the Periodic Ping timer
field.
b)
If all 3 pings to the first destination address fail, the router sends 3 consecutive pings to the second destination address at
the Periodic Ping timer interval.
c)
If all 3 pings to the second destination address fail, the router sends 3 pings to the first destination address using the
Periodic Ping accelerated timer interval.
d)
If all 3 accelerated pings to the first destination address fail, the router sends 3 pings to the second destination address at
the Periodic Ping accelerated timer interval.
e)
If all 3 accelerated pings to the second destination address fail, the router registers this as a fail and returns to step C.
f)
When the number of failures reaches the number configured in the Fail count field, the router reboots. If any ping
succeeds, the router returns to step A and does not reboot.
Note: The Periodic Ping timer should not be set to a value of less than 300 seconds to allow the router time to reconnect to
the cellular network following a reboot.
To disable the periodic ping reset monitor, set Fail count to 0.
Figure 80 – Ping watchdog settings
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
76
www.netcommwireless.com
Configuring Periodic Ping settings
The Periodic Ping settings configure the router to transmit controlled ping packets to 2 specified IP addresses. If the router does not
receive responses to the pings, the router will reboot.
To configure the ping watchdog:
1.
In the First destination address field, enter a website address or IP address to which the router should send the first round
of ping requests.
2.
In the Second destination address field, enter a website address or IP address to which the router should send the second
round of ping requests.
3.
In the Periodic Ping timer field, enter an integer between 300 and 65535 for the number of seconds the router should wait
between ping attempts. Setting this to 0 disables the ping watchdog function.
4.
In the Periodic Ping accelerated timer field, enter an integer between 60 and 65535 for the number of seconds the router
should wait between accelerated ping attempts, i.e. pings to the second destination address. Setting this to 0 disables the
ping watchdog function
5.
In the Fail count field, enter an integer between 1 and 65535 for the number of times an accelerated ping should fail before
the router reboots. Setting this to 0 disables the ping watchdog function.
Disabling the Periodic Ping reset function
To disable the Periodic Ping reset function, set Fail count to 0.
Note: The traffic generated by the periodic ping feature is usually counted as chargeable data usage. Please keep this in
mind when selecting how often to ping.
Configuring a Periodic reboot
The router can be configured to automatically reboot after a period of time specified in minutes. While this is not necessary, it does
ensure that in the case of remote installations, the router will reboot if some anomaly occurs.
1.
In the Force reboot every field, enter the time in minutes between forced reboots. The default value is 0 which disables the
Periodic reboot function. The minimum period between reboots is 5 minutes while the maximum value is 65535 minutes.
2.
If you have configured a forced reboot time, you can use the Randomise reboot time drop down list to select a random
reboot timer. Randomising the reboot time is useful for preventing a large number of devices from rebooting
simultaneously and flooding the network with connection attempts. When configured, the router waits for the configured
Force reboot every time and then randomly selects a time that is less than or equal to the Randomise reboot time setting.
After that randomly selected time has elapsed, the router reboots.
3.
Click the Save button to save the settings.
Note: The randomise reboot time is not persistent across reboots; each time the router is due to reboot, it randomly selects
a time less than or equal to the Randomise reboot time.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
77
SNMP
SNMP configuration
The SNMP page is used to configure the SNMP features of the router.
Figure 81 - SNMP configuration
SNMP (Simple Network Management Protocol) is used to remotely monitor the router for conditions that may warrant administrative
attention. It can be used to retrieve information from the router such as the signal strength, the system time and the interface status.
To configure SNMP:
1.
Click the SNMP toggle key to switch it to the ON position.
2.
Enter Read-only community name and Read-write community name which are used for client authentication.
Community names are used as a type of security to prevent access to reading and/or writing to the routers configuration. It
is recommended that you change the Community names to something other than the default settings when using this
feature.
3.
Click the Save button to save any changes to the settings.
The Download button displays the Management Information Base (MIB) of the router. The MIB displays all the objects of the router
that can have their values set or report their status. The MIB is formatted in the SNMP-related standard RFC1155.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
78
www.netcommwireless.com
SNMP traps
SNMP traps are messages from the router to the Network Management System sent as UDP packets. They are often used to notify
the management system of any significant events such as whether the link is up or down.
Configuring SNMP traps
To configure SNMP traps:
1.
In the Trap destination field, enter the IP address to which SNMP data is to be sent.
2.
In the Heartbeat interval field, enter the number of seconds between SNMP heartbeats.
3.
Use the Trap persistence field to specify the time in seconds that an SNMP trap persists.
4.
Use the Trap retransmission time to specify the length of time in seconds between SNMP trap retransmissions.
Figure 82 - SNMP traps
To send a manual SNMP Heartbeat, click the Send heartbeat button. When you have finished configuring the SNMP traps, click the
Save button to save the settings.
Note: When a factory reset is performed via SNMP, the SNMP settings are preserved.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
79
TR-069
To access the TR-069 configuration page, click the Services menu item, then select the TR-069 menu item on the left.
Figure 83 - TR-069 configuration
The TR-069 (Technical Report 069) protocol is a technical specification also known as CPE WAN Management Protocol (CWMP). It
is a framework for remote management and auto-configuration of end-user devices such as customer-premises equipment (CPE)
and Auto Configuration Servers (ACS). It is particularly efficient in applying configuration updates across networks to multiple CPEs.
TR-069 uses a bi-directional SOAP/HTTP-based protocol based on the application layer protocol and provides several benefits for
the maintenance of a field of CPEs:
Simplifies the initial configuration of a device during installation
Enables easy restoration of service after a factory reset or replacement of a faulty device
Firmware and software version management
Diagnostics and monitoring
Note: You must have your own compatible ACS infrastructure to use TR-069. In order to access and configure the TR-069
settings you must be logged into the router as the root user.
Note: When a factory reset of the router is performed via TR-069, the TR-069 settings are preserved.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
80
www.netcommwireless.com
TR-069 configuration
To configure TR-069:
1.
Click the Enable TR-069 toggle key to switch it to the ON position.
2.
In the ACS URL field, enter the Auto Configuration Server’s full domain name or IP address.
3.
Use the ACS username field to specify the username for the Auto Configuration Server.
4.
In the ACS password and Verify ACS password fields, enter the Auto Configuration Server password.
5.
In the Connection Request Username field, enter the username to use for the connection requests.
6.
In the Connection Request Password and Verify password fields, enter the connection request password.
7.
The inform message acts as a beacon to inform the ACS of the existence of the router. Click the Enable periodic ACS
informs toggle key to turn on the periodic ACS inform messages.
8.
In the Inform Period field, enter the number of seconds between the inform messages.
9.
Click the Save button to save the settings.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
81
Auto Dial Configuration
Using the Auto Dial function, you can configure the router to automatically dial a pre-defined phone number when the handset is
lifted.
Figure 84 - Auto Dial Configuration
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
82
www.netcommwireless.com
USSD
Network Messaging, also known as Unstructured Supplementary Service Data (USSD) is a protocol that can be used to
communicate from your device to your service provider. Depending on which network you use for your mobile broadband service,
this page can be used for a variety of network services such as balance checking, recharging a prepaid service, and many others.
Network messaging can be initiated using special codes specified by your carrier for these various services. Once a special code is
sent to the network, the network responds with the requested information. The response often includes instructions for sending
additional follow-on messages allowing further functionality (e.g entering credit card information for a credit recharge).
Please contact your network provider to learn which codes can be used on your network for features such as balance checking,
recharge, etc
To begin using this feature, please enter the dial string (e.g #100#) into the box below and click “Start Session”. If you don’t know
which dial string to use, please contact your carrier, and ask them which dial codes are suitable for network services.
Figure 85 - USSD Service
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
83
SMS messaging
The NTC-30WV router offers an advanced SMS feature set, including sending messages, receiving messages, redirecting incoming
messages to another destination, as well as supporting remote commands and diagnostics messages.
Some of the functions supported include:
Ability to send a text message via a 2G/3G network and store it in permanent storage.
Ability to receive a text message via a 2G/3G network and store it in permanent storage.
Ability to forward incoming text messages via a 2G/3G network to another remote destination which may be a
TCP/UDP server or other mobile devices.
Ability to receive run-time variables from the device (e.g. uptime) on request via SMS
Ability to change live configuration on the device (e.g. network username) via SMS.
Ability to execute supported commands (e.g. reboot) via SMS
Ability to trigger the NTC-30WV router to download and install a firmware upgrade
Ability to trigger the NTC-30WV router to download and apply a configuration file
To access the SMS messaging functions of the NTC-30WV router, click on the Services menu item from the top menu bar, and
then select one of the options under the SMS messaging section on the left hand menu.
Setup
The Setup page provides the options to enable or disable the SMS messaging functionality and SMS forwarding functionalities of
the router. SMS messaging is enabled by default.
Figure 86 - General SMS Configuration
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
84
www.netcommwireless.com
OPTION
DEFINITION
General SMS configuration
SMS messaging
Toggles the SMS functionality of the router on and off.
Messages per page (10-50)
The number of SMS messages to display per page. Must be a value between 10 and 50.
Encoding scheme
The encoding method used for outbound SMS messages. GSM 7-bit mode permits up to 160
characters per message but drops to 50 characters if the message includes special characters.
UCS-2 mode allows the sending of Unicode characters and permits a message to be up to 50
characters in length.
SMS forwarding configuration
Forwarding
Toggles the SMS forwarding function of the router on and off.
Redirect to mobile
Enter a mobile number as the destination for forwarded SMS messages.
TCP server address
Enter an IP address or domain name as the destination for forwarded SMS messages using
TCP.
TCP port
The TCP port on which to connect to the remote destination.
UDP server address
Enter an IP address or domain name as the destination for forwarded SMS messages using
UDP.
UDP port
The UDP port on which to connect to the remote destination.
Table 20 - SMS Setup Settings
SMS forwarding configuration
Incoming text messages can be redirected to another mobile device and/or a TCP/UDP message server.
Redirect to mobile
You can forward incoming text messages to a different destination number. This destination number can be another mobile phone
or a 3G router phone number.
For Example:
If someone sends a text message and Redirect to mobile is set to “+61412345678”, the text message is stored on the router and
forwarded to “+61412345678” at the same time.
To disable redirection to a mobile, clear the Redirect to mobile field and click the Save button.
Redirect to TCP / UDP server address
You can also forward incoming text messages to a TCP/UDP based destination. The TCP or UDP server can be any kind of public
or private server if the server accepts incoming text-based messages.
The TCP/UDP address can be an IP address or domain name. The port number range is from 1 to 65535. Please refer to your
TCP/UDP based SMS server configuration for which port to use.
For Example:
If someone sends a text message and TCP server address is set to “192.168.20.3” and TCP port is set to “2002”, this text
message is stored in the router and forwarded to “192.168.20.3” on port “2002” at the same time.
To disable redirection to a TCP or UDP address, clear the TCP server address and UDP server address fields and click the Save
button.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
85
New message
The New message page can be used to send SMS text messages to a single or multiple recipients.
A new SMS message can be sent to a maximum of 9 recipients at the same time. After sending the message, the result is displayed
next to the destination number as “Success” or “Failure” if the message failed to send. By default, only one destination number field
is displayed. Additional destination numbers may be added one at a time after entering a valid number for the current destination
number field. To add a destination number, click the
button and to remove the last destination in the list, click the
button.
Figure 87 - SMS - New Message
Destination numbers should begin with the “+” symbol followed by the country calling code. To send a message to a destination
number, enter the “+” symbol followed by the country calling code and then the destination number.
For example:
To send a message to the mobile destination number 0412345678 in Australia (country calling code 61), enter
“+61412345678”.
After entering the required recipient numbers, type your SMS message in the New message field. As you type your message, a
counter shows how many characters you have entered out of the total number available for your chosen encoding scheme. When
you have finished typing your message and you are ready to send it, click the Send button.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
86
www.netcommwireless.com
Inbox / Sent Items
The Inbox displays all received messages that are stored on the router while Sent Items displays all sent messages.
Figure 88 - SMS Inbox
Figure 89 - SMS Outbox
ICON
DESCRIPTION
Forward button. Click this button to open a new message window where you can forward the corresponding
message to another recipient.
Reply button. Click this button to open a new message window where you can reply to the sender.
Add to White list. Click this button to add the sender’s mobile number to the white list on the router.
Delete button. Click this button to delete the corresponding message.
Refresh button. Click this button to refresh the inbox or outbox to see new messages.
Table 21 - Inbox/Outbox icons
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
87
Diagnostics
The Diagnostics page is used to configure the SMS diagnostics and command execution configuration. This allows you to change
the configuration, perform functions remotely and check on the status of the router via SMS commands.
To access the Diagnostics page, click on the Services menu item then select the SMS menu on the left and finally select
Diagnostics beneath it.
Figure 90 - SMS diagnostics and command execution configuration
SMS diagnostics and command execution configuration
The options on this page are described below.
Enable remote diagnostics and command execution
Enables or disables the remote diagnostics feature. If this setting is enabled all incoming text messages are parsed and tested for
remote diagnostics commands.
If remote diagnostics commands are found, the router executes those commands. This feature is enabled by default. All remote
diagnostic commands that are received are stored in the Inbox.
Note: It is possible to adjust settings and prevent your router from functioning correctly using remote diagnostics. If this
occurs, you will need to perform a factory reset in order to restore normal operation.
We highly recommended that you use the white list and a password when utilising this feature to prevent unauthorised
access. See the White list description for more information.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
88
www.netcommwireless.com
Only accept authenticated SMS messages
Enables or disables checking the sender’s phone number against the allowed sender white list for incoming diagnostics and
command execution SMS messages.
If authentication is enabled, the router will check if the sender’s number exists in the white list. If it exists, the router then checks the
password (if configured) in the incoming message against the password in the white list for the corresponding sending number. If
they match, the diagnostic or command is executed.
If the number does not exist in the white list or the password does not match, the router does not execute the incoming diagnostic
or command in the SMS message.
This is enabled by default and it is strongly advised that you leave this feature enabled to maintain security.
Send Set command acknowledgement replies
The NTC-30WV router will automatically reply to certain types of commands received, such as get commands, or execute
commands. However acknowledgement replies from the NTC-30WV router are optional with set commands and the Wakeup
command. This option Enables or disables sending an acknowledgment message after execution of a set command or SMS
Wakeup command. If disabled, the router does not send any acknowledgement after execution of a set command or SMS Wakeup
command. All acknowledgment replies are stored in the Outbox after they have been sent. This can be useful to determine if a
command was received and executed by the router. This option is disabled by default.
Access advanced RDB variables
By default, this option is turned off and only allows access to the basic RDB variables listed later in this guide. If this option is
enabled, you are able to access the full list of RDB variables via SMS.
Allow execution of advanced commands
By default, this option is turned off and only allows execution of the basic commands listed later in this guide. If this option is
enabled, you are able to execute advanced commands such as those which are common to the Linux command line. For example:
“execute ls /usr/bin/sms*” to list the contents of the /etc folder on the router.
Send acknowledgement replies to
This option allows you to specify where to send acknowledgment messages after the execution of a set, get, or exec command.
If a fixed number is selected, the acknowledgement message will be sent to the number defined in the Fixed number to send replies
to field. If the sender’s number is selected, the acknowledgement message will be sent to the number that the SMS diagnostic or
command message originated from. The default setting is to use the sender’s number.
Fixed number to send replies to
This field defines the destination number to which error messages are sent after the execution of a get, set, or exec command. This
field is only displayed when Send Error SMS to is set to Fixed Number.
Send command error replies
Enables or disables the sending of an error message resulting from the execution of a get, set, or exec command. All error replies
are stored in the Outbox after they have been sent.
Send error replies to
When Send Error SMS for Get/Set/Exec Command is set to ON, this option is used to specify where the error SMS is sent. Use the
radio buttons to select either Fixed Number or SMS Sender Number. When set to SMS Sender Number the router will reply to the
originating number of the SMS diagnostic or command. When set to Fixed Number the router will send the error messages to the
number specified in the following field.
Send a maximum number of
You can set the maximum number of acknowledgement and error messages sent when an SMS diagnostic or command is
executed. The maximum limit can be set per hour, day, week or month. The router will send a maximum of 100 replies by default.
The number of messages sent is shown below the options. The total transmitted message count resets after a reboot or at the
beginning of the time frame specified.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
89
White List for diagnostic or execution SMS
The white list is a list of mobile numbers that you can create which are considered “friendly” to the router. If Only accept
authenticated SMS messages is enabled in the diagnostics section, the router will compare the mobile number of all incoming
diagnostic and command messages against this white list to determine whether the diagnostic or command should be executed.
You may optionally configure a password for each number to give an additional level of security. When a password is specified for a
number, the SMS diagnostic or command message is parsed for the password and will only be executed if the number and
password match.
Figure 91 - White list for diagnostic or execution SMS
A maximum of 20 numbers can be stored on the router in the white list. To add a number to the white list, click the “+Add” button.
Figure 92 – Adding a number to the SMS white list
The White List numbers and passwords can be cleared by pressing the
button to the right of each entry. To add a number to
the white list, enter it in the Destination number field and optionally define a password in the Password field. When you have finished
adding numbers click the Save button to save the entries.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
90
www.netcommwireless.com
Sending an SMS Diagnostic Command
Follow the steps below to configure the router to optionally accept SMS diagnostic commands only from authenticated senders and
learn how to send SMS diagnostic commands to the router.
1.
Navigate to the Services > SMS messaging > Diagnostics page
2.
Confirm that the Enable remote diagnostics and command execution toggle key is set to the ON position. If it is set to OFF
click the toggle key to switch it to the ON position.
3.
If you wish to have the router only accept commands from authenticated senders, ensure that Only accept authenticated
SMS messages is set to the ON position. In the White list for diagnostic or execution SMS messages section, click the
+Add button and enter the sender’s number in international format into the Destination number field that appears. If you
wish to also configure a password, enter the password in the Password field corresponding to the destination number.
4.
If you would prefer to accept SMS diagnostic commands from any sender, set the Only accept authenticated SMS
messages toggle key to the OFF position.
Note: An alternative method of adding a number to the white list is to send an SMS message to the router, navigate to
Services > SMS messaging > Inbox and then click the
button next to the message which corresponds to the sender’s
number.
5.
Click the Save button.
Types of SMS diagnostic commands
There are three types of commands that can be sent; execute, get and set. The basic syntax is as follows:
execute COMMAND
get VARIABLE
set VARIABLE=VALUE
If authentication is enabled, each command must be preceded by the password:
PASSWORD execute COMMAND
PASSWORD get VARIABLE
PASSWORD set VARIABLE=VALUE
The following are some examples of SMS diagnostic commands:
password6657 execute reboot
get rssi
set apn1=testAPNvalue
SMS acknowledgment replies
The router automatically replies to get commands with a value and execute commands with either a success or error response. Set
commands will only be responded to if the Send Set command acknowledgement replies toggle key is set to ON. If the Send
command error replies toggle key is set to ON, the router will send a reply if the command is correct but a variable or value is
incorrect, for example, due to misspelling.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
91
SMS command format
Generic Format for reading variables:
get VARIABLE
PASSWORD get VARIABLE
Generic Format for writing to variables:
set VARIABLE=VALUE
PASSWORD set VARIABLE=VALUE
Generic Format for executing a command:
Execute COMMAND
PASSWORD execute COMMAND
Replies
Upon receipt of a successfully formatted, authenticated (if required) command, the gateway will reply to the SMS in the following
format:
TYPE
SMS CONTENTS
get command
“VARIABLE=VALUE”
set command
“Successfully set VARIABLE to VALUE”
execute command
“Successfully executed command COMMAND”
NOTES
Only sent if the acknowledgment message
function is enabled
Table 22 - SMS Diagnostic Command Syntax
Where “VARIABLE” is the name of the value to be read
Where “VARIABLE (x)” is the name of another value to be read
Where “VALUE” is the content to be written to the “VARIABLE”
Where “COMMAND” is a supported command to be executed by the device (e.g. reboot)
Where “PASSWORD” is the password (if configured) for the corresponding sender number specified in the White List
Multiple commands can be sent in the same message, if separated by a semicolon.
For Example:
get VARIABLE1; get VARIABLE2; get VARIABLE3
PASSWORD get VARIABLE1; get VARIABLE2
set VARIABLE=VALUE1 ; set VARIABLE2=VALUE2
PASSWORD set VARIABLE1=VALUE1; set VARIABLE2=VALUE2; set VARIABLE3=VALUE3
If required, values can also be bound by an apostrophe, double apostrophe or back tick.
For Example:
“set VARIABLE=’VALUE’”
“set VARIABLE=”VALUE””
“set VARIABLE=`VALUE`”
“get VARIABLE”
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
92
www.netcommwireless.com
A password (if required), only needs to be specified once per SMS, but can be prefixed to each command if desired.
“PASSWORD get Variable1”; “get VARIABLE2”
“PASSWORD set VARIABLE1=VALUE1”; “set VARIABLE2=VALUE2”
If the command sent includes the “reboot” command and has already passed the white list password check, the device keeps this
password and executes the remaining command line after the reboot with this same password.
For Example:
“PASSWORD execute reboot; getVariable1”; “get VARABLE2”
“PASSWORD execute reboot; PASSWORD get Variable1”; “get VARABLE2”
Note: Commands, variables and values are case sensitive.
List of basic commands
A list of basic commands which can be used in conjunction with the execute command are listed below:
“pdpcycle”, “pdpdown” and “pdpup” commands can have a profile number suffix ‘x’ added. Without the suffix specified, the
command operates against the default profile configured on the profile list page of the Web-UI.
#
1
COMMAND NAME
DESCRIPTION
reboot
Immediately performs a soft reboot.
2
pdpcycle
Disconnects (if connected) and reconnects the data connection. If a profile number is selected in the
command, try to disconnect/reconnect the specified profile in case the profile is active. If no profile
number is selected, try to disconnect/reconnect the current active profile. Reports an error if no profile
number is selected and there is no currently activated profile.
3
pdpdown
Disconnects the PDP. If a profile number is selected in the command, the router tries to disconnect the
specified profile in case the profile is active. If no profile number is selected, try to disconnect the current
active profile. Reports an error if no profile number is selected and there is no currently activated profile.
4
pdpup
Reconnects the PDP. If a profile number is selected in the command, the router tries to connect with
the specified profile. If no profile number is selected, the router tries to connect to the last active profile.
The gateway will check the currently activated profile and disconnect this profile before executing the
command. The router reports an error if no profile number is selected and there is no stored last active
profile number.
5
factorydefaults
Performs a factory reset on the router. Be aware that this command also clears the SMS white list on
the router.
Performs a download and install of a Firmware Upgrade (.cdi), Config File (.tar.gz) or a help document
(.pdf) file.
If the file is a firmware image as in the case of a .cdi file, the router will apply the recovery image first and
then the main firmware image. The download location is specified immediately after the command and
may be from an HTTP or FTP source URL.
If the file is a .tar.gz file, the router will apply the file as a configuration file update for the device and
reboot afterwards.
6
download
If the file is a .pdf, the router will assume this is a user guide document and save it to the router and
make the file available for viewing via the help menu on the Web-UI.
Note: If your download URL includes any space characters, please encode these prior to transmission
according to RFC1738, for example:
ftp://username:password@serveraddress/directory%20with%20spaces/filename.cdi
Note: Authenticated FTP addresses may be used following the format as defined in RFC1738, for
example:
ftp://username:password@serveraddress/directory/filename.cdi
7
ssh.genkeys
Instructs the router to generate new public SSH keys.
8
ssh.clearkeys
Instructs the router to clear the client public SSH key files.
Table 23 - List of basic SMS diagnostic commands
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
93
List of get/set commands
The following table is a partial list of get and set commands which may be performed via SMS.
COMMAND
NAME
EXAMPLE
DESCRIPTION
get status
get status
Returns the Module firmware version, LAN IP Address, Network State, Network operator and
RSSI.
get sessionhistory
get sessionhistory
Returns the time and date of recent sessions along with the total amount of data sent and
received for each session.
set syslogserver
set
syslogserver=123.45.67.89:514
Sets a remote syslog server IP or hostname and port.
get plmnscan
get plmnscan
Instructs the router to perform a network scan and returns the results by SMS.
set forceplmn
set forceplmn=505,3
Sets the operator to a manual selection made by the user where “505” is the Mobile Country
Code for Australia and “3” is the Mobile Network Code for Vodafone. As no network type (i.e.
3G or 2G) is specified, it is selected automatically.
get forceplmn
get forceplmn
Returns the operator and network type selection mode (Automatic/Manual), in addition to the
MCC and MNC values
get pppoe
get pppoe
Returns the PPPoE status, currently configured dial string and service name
set pppoe
set pppoe=1, telstra.internet, test
Sets the PPPoE status on, APN to telstra.internet, and service name to test.
get ledmode
get ledmode
Returns the status of the LED operation mode.
set ledmode
set ledmode=10
Sets the LED operation mode to be always on or to turn off after the specified number of
minutes.
get ssh.proto
get ssh.proto
Returns the SSH protocol in use.
set ssh.proto
set ssh.proto=1,2
Sets the SSH Protocol to protocol 1, 2 or both (1,2).
get ssh.passauth
get ssh.passauth
Returns the status of the SSH Enable password authentication option.
set ssh.passauth
set ssh.passauth=1
Sets the SSH Enable password authentication option on or off.
get.ssh.keyauth
get.ssh.keyauth
Returns the status of the SSH Enable key authentication option.
set.ssh.keyauth
set.ssh.keyauth=1
Sets the SSH Enable key authentication option on or off.
Table 24 - List of get/set commands
List of basic RDB variables
The following table lists valid variables where “x” is a profile number (1-6). If no profile is specified, variables are read from or written
to for the current active profile. If a profile is specified, variables are read from or written to for the specified profile number (‘x’).
#
RDB VARIABLE NAME
SMS VARIABLE
NAME
READ/
WRITE
DESCRIPTION
Read:
link.profile.1.enable
(profile no,apn,user,pass,auth,iplocal,status)
link.profile.1.apn
link.profile.1.user
0
link.profile.1.pass
EXAMPLE VALUE
profile
1,apn,username,password,
chap,202.44.185.111,up
RW
Profile
link.profile.1.auth_type
Write:
link.profile.1.iplocal
(apn, user, pass,auth)
link.profile.1.status
apn,username,password
2
link.profile.1.user
username
RW
3G username
Guest, could also return “null”
3
link.profile.1.pass
password
RW
3G password
Guest, could also return “null”
4
link.profile.1.auth_type
authtype
RW
3G Authentication
type
”pap” or”chap”
5
link.profile.1.iplocal
wanip
R
WAN IP address
202.44.185.111
6
wwan.0.radio.information.signal_strength
rssi
R
3G signal strength
-65 dBm
7
wwan.0.imei
imei
R
IMEI number
357347050000177
8
statistics.usage_current
usage
R
3G data usage of
current session
“Rx 500 bytes, Tx 1024 bytes, Total 1524
bytes” or “Rx 0 byte, Tx 0 byte, Total 0 byte”
when wwan down
9
statistics.usage_current
wanuptime
R
Up time of current 3G
session
1 days 02:30:12 or 0 days 00:00:00 when
wwan down
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
94
www.netcommwireless.com
10
/proc/uptime
deviceuptime
R
Device up time
1 days 02:30:12
11
wwan.0.system_network_status.current_ba
nd
band
R
Current band
WCDMA850
Table 25 - List of basic SMS diagnostics RDB variables
Network scan and manual network selection by SMS
Performing a network scan
The get plmnscan SMS command enables you to perform a scan of the cellular networks available at the time of the scan.
It returns the following semi-colon separated information for each network in range:

MCC

MNC

Network Type (3G, 2G)

Provider's Name

Operator Status (available, forbidden, current)
The following is an example of a response from the get plmnscan SMS command:
plmnscan:505,3,7,vodafone AU,4;505,3,1,vodafone AU,1;505,2,7,YES OPTUS,1;505,2,1,YES OPTUS,1;505,1,1,Telstra
Mobile,1;505,1,7,Telstra Mobile,1
NETWORK
TYPE
DESCRIPTION
7
Indicates a 3G network
1
Indicates a 2G network
Table 26 - Network types returned by get plmnscan SMS command
OPERATOR
STATUS
DESCRIPTION
1
Indicates an available operator which may be selected.
2
Indicates a forbidden operator which may not be selected (applies only to generic SIM cards).
4
Indicates the currently selected operator.
Table 27 - Operator status codes returned by get plmnscan SMS command
Notes about the network connection status when using the get plmnscan command:

If the connection status is Up and connection mode is Always on, the get plmnscan SMS will cause the connection to
disconnect, perform the scan, send the result through SMS and then bring the connection back up again. If the
connection status is Down, the router will perform the PLMN scan, send the result and keep the connection status down.

If the connection status is Waiting and connection mode is Connect on demand, the get plmnscan SMS will change the
connection status to Down, perform the scan, send the result through SMS and then restore the connection status to the
Waiting state.

If the connection status is Up and connection mode is Connect on demand, the get plmnscan SMS will cause the
connection to disconnect, perform the scan, send the result through SMS, and then restore the connection status to the
Waiting state unless there is a traffic which triggers a connection in which case the connection status will be set to Up.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
95
Setting the router to connect to a network
The router can be instructed by SMS to connect to one of the networks returned by the get plmnscan command. The set forceplmn
command forces the router to connect to a specified operator network (if available) while the get forceplmn command retrieves the
currently configured network on the router.
Command format:
set forceplmn=0|MCC,MNC| MCC,MNC,Network Type
For example:
set forceplmn=0
Sets the selection of operator and network type to automatic mode.
set forceplmn=505,3
Sets the operator to a manual selection made by the user where “505” is the Mobile Country Code for Australia and “3” is
the Mobile Network Code for Vodafone. As no network type (i.e. 3G or 2G) is specified, it is selected automatically.
set forceplmn=505,3,7
Sets the operator and network type to a manual selection made by the user where “505” is the Mobile Country Code for
Australia, “3” is the Mobile Network Code for Vodafone and “7” is the 3G network type.
Notes about the set forceplmn command:
1.
If the manual selection fails, the device will fall back to the previous ‘good’ network.
2.
When enabled, the SMS acknowledgement reply reflects the success or failure of the manual selection with respect to
the set command and includes the final MNC/MCC that was configured.
Confirming the currently configured operator and network type
You can retrieve the currently configured operator and network type using the get forceplmn command.
The get forceplmn command returns the operator and network type selection mode (Automatic/Manual), in addition to the MCC
and MNC values, for example:
Automatic,505,3
This response indicates that the operator/network selection mode is Automatic, and the network used is Vodafone AU.
SMS diagnostics examples
The examples below demonstrate various combinations of supported commands. This is not an exhaustive list and serves as an
example of possibilities only.
DESCRIPTION
AUTHENTICATION
Send SMS to change the data
connection username
Not required
set username=’NetComm’
Required
PASSWORD set username= ”NetComm”
Send SMS to change the data
connection password
Not required
set password= `NetComm`
Required
PASSWORD set password= `NetComm`
Send SMS to change the data
connection authentication
Not required
set authtype= ‘pap’
Required
PASSWORD set authtype = pap
Not required
execute reboot
Required
PASSWORD execute reboot
Not required
get wanip
Required
PASSWORD get wanip
Send SMS to check the mobile
signal strength
Not required
get rssi
Required
PASSWORD get rssi
Send SMS to check the IMEI
number
Not required
get imei
Required
PASSWORD get imei
Send SMS to reboot
Send SMS to check the WAN IP
address
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
96
INPUT EXAMPLE
www.netcommwireless.com
Send SMS to check the current
band
Not required
get band
Required
PASSWORD get band
Send SMS to Disconnect (if
connected) and reconnect the data
connection
Not required
execute pdpcycle
Required
PASSWORD execute pdpcycle
Not required
execute pdpdown
Required
PASSWORD execute pdpdown
Not required
execute pdpup
Required
PASSWORD execute pdpup
Not required
get wanip; get rssi
Required
PASSWORD get wanip; get rssi
Not required
set ssh.genkeys=1; set username=test; set auth=pap
Required
PASSWORD set ssh.genkeys=1; set username=test; set auth=pap
Send SMS to reset to factory default
settings
Not required
execute factorydefaults
Required
PASSWORD execute factorydefaults
Send SMS to retrieve status of
router
Not required
get status
Required
PASSWORD get status
Send SMS to retrieve the history of
the session, including start time, end
time and total data usage
Not required
get sessionhistory
Required
PASSWORD get sessionhistory
Send SMS to configure the router to
send syslog to a remote syslog
server
Not required
set syslogserver=123.209.56.78
Required
PASSWORD set syslogserver=123.209.56.78
Send SMS to wake up the router,
turn on the default gateway and
trigger the ‘connect on demand’
profile if in waiting state.
Not required
execute wakeup
Required
PASSWORD execute wakeup
Send SMS to disconnect the data
connection
Send SMS to connect the data
connection
Send multiple get command
Send multiple set command
Not required
Send SMS to perform firmware
upgrade when firmware is located
on HTTP server
execute download http://download.com:8080/firmware_image_r.cdi
PASSWORD execute download http://download.com:8080/firmware_image.cdi
Required
Not required
Send SMS to perform firmware
upgrade when firmware is located
on FTP server
Required
Send SMS to download and install
IPK package located on HTTP
server
execute download http://download.com:8080/firmware_image.cdi
PASSWORD execute download
http://download.com:8080/firmware_image_r.cdi
execute download
ftp://username:password@download.com/firmware_image.cdi
execute download ftp://username:password@
download.com/firmware_image_r.cdi
PASSWORD execute download ftp://username:password@
download.com/firmware_image.cdi
PASSWORD execute download ftp://username:password@
download.com/firmware_image_r.cdi
Not required
execute download http://download.com:8080/package.ipk
Required
PASSWORD execute download http://download.com:8080/package.ipk
Not required
execute download ftp://username:password@
download.com:8080/package.ipk
Required
PASSWORD execute download ftp://username:password@
download.com:8080/package.ipk
Not required
set pppoe=0
Required
PASSWORD set pppoe=0
Send SMS to retrieve the PPPoE
status, currently configured dial
string and service name
Not required
get pppoe
Required
PASSWORD get pppoe
Send SMS to set the LED mode
timeout to 10 minutes
Not required
set ledmode=10
Required
PASSWORD set ledmode=10
Send SMS to retrieve the current
LED mode
Not required
get ledmode
Required
PASSWORD get ledmode
Retrieve current SSH protocol
Not required
get ssh.proto
Send SMS to download and install
IPK package located on FTP server
Send SMS to turn off PPPoE
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
97
Required
PASSWORD get ssh.proto
Not required
set ssh.proto=1
Required
PASSWORD set ssh.proto=1
Retrieve password authentication
status
Not required
get ssh.passauth
Required
PASSWORD get.ssh.passauth
Enable/disable password
authentication on host
Not required
set ssh.passauth=1 or set ssh.passauth=0
Required
PASSWORD set ssh.passauth=1 or PASSWORD set ssh.passauth=0
Generate set of public/private keys
on the host
Not required
execute ssh.genkeys
Required
PASSWORD execute ssh.genkeys
Clear client public keys stored on
host
Not required
execute ssh.clearkeys
Required
PASSWORD execute ssh.clearkeys
Select SSH protocol
Table 28 - SMS diagnostics example commands
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
98
www.netcommwireless.com
System
Log
The Log pages are used to display or download the System log and IPSec logs on the router.
System log
The System Log enables you to troubleshoot any issues you may be experiencing with your NTC-30WV router. To access the
System Log page, click on the System menu. The System Log is displayed.
Figure 93 - System log file
Log file
Use the Display level drop-down list to select a message level to be displayed. The message levels are described in the table below.
To download the System log for offline viewing, right-click the Download button and choose Save as.. to save the file. To clear the
System log, click the Clear button. The downloaded log file is in Linux text format with carriage return (CR) only at the end of a line,
therefore in order to be displayed correctly with new lines shown, it is recommended to use a text file viewer which displays this
format correctly (e.g. Notepad++).
Log data is stored in RAM and therefore, when the unit loses power or is rebooted, it will lose any log information stored in RAM. To
ensure that log information is accessible between reboots of the router there are two options:
1.
Enable the Log to non-volatile memory option
2.
Use a remote syslog server
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
99
Enable the log to non-volatile memory option
When the router is configured to log to non-volatile memory, the log data is stored in flash memory, making it accessible after a
reboot of the router. Up to 512kb of log data will be stored before it is overwritten by new log data. Flash memory has a finite
number of program-erase operations that it may perform to the blocks of memory. While this number of program-erase operations
is quite large, we recommend that you do not enable this option for anything other than debugging to avoid excessive wear on the
memory.
Use a remote syslog server
The router can be configured to output log data to a remote syslog server. This is an application running on a remote computer
which accepts and displays the log data. Most syslog servers can also save the log data to a file on the computer on which it is
running allowing you to ensure that no log data is lost between reboots.
To configure the NTC-30WV router to output log data to a remote syslog server:
1.
Click on the System menu from the top menu bar. The System log item is displayed.
2.
Under the Remote syslog server section, enter the IP address or hostname of the syslog server in the IP / Hostname
[:PORT] field. You can also specify the port number after the IP or hostname by entering a semi-colon and then the port
number e.g. 192.168.1.102:514. If you do not specify a port number, the router will use the default UDP port 514.
3.
Click the Save button to save the configuration.
Figure 94 - System log
ITEM
DEFINITION
Debug
Show extended system log messages with full debugging level details.
Info
Show informational messages only.
Notice
Show normal system logging information.
Error
Show error condition messages only.
Table 29 - System log detail levels
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
100
www.netcommwireless.com
IPSec log
The IPSec log section provides the ability for you to download the log for the IPSec VPN function. This can assist in troubleshooting
any problems you may have with the IPSec VPN.
Figure 95 - IPSec log
Use the Log level drop down list to specify the type of detail you want to capture in the log and then click the Save button. When
you change the logging level, any active IPSec VPN tunnels will be disconnected as a change in logging level requires the IPSec
service to be restarted.
To download the IPSec log, click the Download IPSec log button and you will be prompted to save the file.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
101
System Configuration
Settings backup and restore
The settings backup and restore page is used to backup or restore the router’s configuration or to reset it to factory defaults. In
order to view the settings page you must be logged into the web user interface as root using the password admin. The backup /
restore functions can be used to easily configure a large number of NTC-30WV router by configuring one router with your desired
settings, backing them up to a file and then restoring that file to multiple NTC-30WV routers.
Figure 96 – Settings backup and restore
Back up your router’s configuration
Log in to the web configuration interface, click on the System menu and select Settings backup and restore.
If you want to password protect your backup configuration files, enter your password in the fields under Save a copy of current
settings and click on Save. If you don’t want to password protect your files, just click on Save. The router will then prompt you to
select a location to save the settings file.
Note: The following conditions apply:

It is NOT possible to edit the contents of the file downloaded; if you modify the contents of the configuration file in any way
you will not be able to restore it later.
You may change the name of the file if you wish but the filename extension must remain as “.cfg”
Restore your backup configuration
1.
In the web configuration interface click on the System menu and select Settings backup and restore.
2.
From the Restore saved settings section, click on Browse or Choose a file and select the backup configuration file on your
computer.
3.
Click Restore to copy the settings to the new NTC-30WV router. The router will apply these settings and inform you it will
reboot - click on OK.
Restoring the router’s factory default configuration
Click the Restore defaults button to restore the factory default configuration. The router asks you to confirm that you wish to restore
factory default settings. If you wish to continue with the restoring of factory defaults, click OK.
Note: All current settings on the router will be lost when performing a restore of factory default settings. The device IP
address will change to 192.168.1.1 and the default username root and default password admin will be configured.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
102
www.netcommwireless.com
Upload
To access the Upload page, click on the System menu, then System Configuration and then Upload.
The Upload page allows you to upload firmware files, HTTPS certificates or user created application packages to the NTC-30WV
router. When firmware files have been uploaded, they can also be installed from this page. PDF files, such as this user guide may
also be uploaded for access on the router’s help page.
For more information on application development, contact NetComm Wireless about our Software Development Kit.
Figure 97 - Upload page
Updating the Firmware
The firmware update process involves first updating the recovery image firmware and then updating the main firmware image.
Note: In order to perform an update, you must be logged into the router with the root manager account (see the Advanced
configuration section for more details).
To update the NTC-30WV router’s firmware:
1.
Power on the router as described in the Installing the router section.
2.
Log in to the router with the root user account (See the Advanced configuration section for details)
3.
Select the System item from the top menu bar, select the System configuration item from the menu on the left and then
select the Upload menu item.
4.
Under the File uploads section, click the Choose a file button. Locate the recovery firmware image file on your computer
and click Open. The recovery image is named ntc_6908_x.x.x.x_r.cdi while the main system firmware image is named
ntc_6908_x.x.x.x.cdi.
5.
Click the Upload button. The firmware image is uploaded to the storage on the router.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
103
Figure 98 - File upload
6.
Repeat steps 4 and 5 for the main system firmware image.
7.
The uploaded firmware images are listed in the Uploaded files section. Click the Install link next to the recovery image to
begin installing the recovery firmware image and then click OK on the confirmation window that appears.
Figure 99 - Uploaded files
8.
The recovery firmware image is flashed and when it is complete, the router displays “The firmware update was successful”
and returns to the main Upload screen.
Figure 100 - Recovery firmware flash process
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
104
www.netcommwireless.com
9.
Click the Install link to the right of the main firmware image you uploaded and then click OK to confirm that you want to
continue with the installation.
Note: Do not remove the power when the router’s LEDs are flashing as this is when the firmware update is in process.
10. The installation is complete when the countdown reaches zero. The router attempts to redirect you to the Status page.
Figure 101 -– Installing main firmware image
11. Hold down the reset button on the router for more than 15 seconds (when all LEDs stop flashing) to reboot and restore the
factory default settings of the router. See the Restoring factory default settings section for more information.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
105
Package manager
The Package Manager page is used to provide details of any user installed packages on the router and allow them to be uninstalled.
For more information on application development, contact NetComm Wireless about our Software Development Kit.
Figure 102 – Software applications manager
The Application name, Version number of the application, the architecture type and time of installation are all displayed. Clicking the
Package details link will display a pop-up window with further details of the package.
To uninstall any software applications, click the Uninstall link.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
106
www.netcommwireless.com
Administration settings
To access the Administration Settings page, click on the System menu then the Administration menu on the left and then click on
Administration Settings.
The Administration settings page is used to enable or disable protocols used for remote access and configure the passwords for
the user accounts used to log in to the router.
Figure 103 - Administration page
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
107
OPTION
DEFINITION
Remote router access control
Enable HTTP
Enable or disable remote HTTP access to the router. You can also set the port you would like remote HTTP access to be available on.
HTTP management
port
Enter a port number between 1 and 65534 to use when accessing the router remotely.
Enable HTTPS
Enable or disable remote HTTPS access to the router using a secure connection.
Remote HTTPS
access port
Enter a port number between 1 and 65534 to use when accessing the router remotely over a secure HTTPS connection.
Enable Telnet
Enable or disable remote telnet (command line) access to the router.
Enable SSH
Enable or disable Secure Shell on the router.
Remote SSH Access
Port
Enter the port number for remote SSH access. Must be a port number between 1 and 65534.
Enable Ping
Enable or disable remote ping responses on the WWAN connection.
Local router access control (Telnet/SSH)
Web User Interface account
Username
Use the drop down list to select the root or admin account to change its web user interface password.
Password
Enter the desired web user interface password.
Confirm password
Re-enter the desired web user interface password.
Telnet/SSH account
Username
Displays the Telnet/SSH.username. This may not be changed.
Password
Enter the desired Telnet/SSH password.
Confirm password
Re-enter the desired Telnet/SSH password.
Table 30 - Administration configuration options
To access the router’s configuration pages remotely:
1.
Open a new browser window and navigate to the WAN IP address and assigned port number of the router, for example
http://123.209.130.249:8080
Note: You can find the router’s WAN IP address by clicking on the “Status” menu. The WWAN IP field in the WWAN
Connection Status section shows the router’s WAN IP address.
2.
Enter the username and password to login to the router and click Log in.
Note: To perform functions like Firmware upgrade, device configuration backup and to restore and reset the router to factory
defaults, you must be logged in with the root manager account.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
108
www.netcommwireless.com
HTTPS key management
What is HTTP Secure?
HTTP Secure or HTTPS is the use of the HTTP protocol over an SSL/TLS protocol. It is used primarily to protect against
eavesdropping of communication between a web browser and the web site to which it is connected. This is especially important
when you wish to have a secure connection over a public network such as the internet. HTTPS connections are secured through
the use of certificates issued by trusted certificate authorities such as VeriSign. When a web browser makes a connection attempt
to a secured web site, a digital certificate is sent to the browser so that it can verify the authenticity of the site using a built-in list of
trusted certificate authorities.
There are two main differences between how HTTPS and HTTP connections work:
1.
HTTPS uses port 443 while HTTP uses port 80 by default.
2.
Over an HTTPS connection, all data sent and received is encrypted with SSL while over an HTTP connection, all data is
sent unencrypted.
The encryption is achieved through the use of a pair of public and private keys on both sides of the connection. In cryptography, a
key refers to a numerical value used by an algorithm to alter information (encrypt it), making the information secure and visible only
to those who have the corresponding key to recover (decrypt) the information. The public key is used to encrypt information and
can be distributed freely. The private key is used to decrypt information and must be secret by its owner.
Each NTC-30WV router contains a self-signed digital certificate which is identical on all NTC-30WV routers. For a greater level of
security, the router also supports generating your own unique key. Additionally, you may use third party software to generate your
own self-signed digital certificate or purchase a signed certificate from a trusted certificate authority and then upload those
certificates to the router.
Generating your own self-signed certificate
To generate your own self-signed certificate:
1.
Click the System item from the top menu bar, then Administration from the side menu bar and then HTTPS key
management.
2.
Enter the certificate details using the appropriate fields. Each field must be completed in order to generate a certificate.
Figure 104 - Generate self signed HTTPS certificate
Note: The Country field must contain a code for the desired country from the list below.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
109
CODE
COUNTRY
CODE
COUNTRY
CODE
COUNTRY
CODE
COUNTRY
AX
Åland Islands
ER
Eritrea
LS
Lesotho
SA
Saudi Arabia
AD
Andorra
ES
Spain
LT
Lithuania
SB
Solomon Islands
AE
United Arab Emirates
ET
Ethiopia
LU
Luxembourg
SC
Seychelles
AF
Afghanistan
FI
Finland
LV
Latvia
SE
Sweden
AG
Antigua and Barbuda
FJ
Fiji
LY
Libya
SG
Singapore
AI
Anguilla
FK
Falkland Islands (Malvinas)
MA
Morocco
SH
St. Helena
AL
Albania
FM
Micronesia
MC
Monaco
SI
Slovenia
AM
Armenia
FO
Faroe Islands
MD
Moldova
SJ
AN
Netherlands Antilles
FR
France
ME
Montenegro
SK
Svalbard and Jan Mayen
Islands
Slovak Republic
AO
Angola
FX
France, Metropolitan
MG
Madagascar
SL
Sierra Leone
AQ
Antarctica
GA
Gabon
MH
Marshall Islands
SM
San Marino
AR
Argentina
GB
Great Britain (UK)
MK
Macedonia
SN
Senegal
AS
American Samoa
GD
Grenada
ML
Mali
SR
Suriname
AT
Austria
GE
Georgia
MM
Myanmar
ST
Sao Tome and Principe
AU
Australia
GF
French Guiana
MN
Mongolia
SU
USSR (former)
AW
Aruba
GG
Guernsey
MO
Macau
SV
El Salvador
AZ
Azerbaijan
GH
Ghana
MP
SZ
Swaziland
BA
Bosnia and Herzegovina
GI
Gibraltar
MQ
Northern Mariana
Islands
Martinique
TC
Turks and Caicos Islands
BB
Barbados
GL
Greenland
MR
Mauritania
TD
Chad
BD
Bangladesh
GM
Gambia
MS
Montserrat
TF
French Southern Territories
BE
Belgium
GN
Guinea
MT
Malta
TG
Togo
BF
Burkina Faso
GP
Guadeloupe
MU
Mauritius
TH
Thailand
BG
Bulgaria
GQ
Equatorial Guinea
MV
Maldives
TJ
Tajikistan
BH
Bahrain
GR
Greece
MW
Malawi
TK
Tokelau
BI
Burundi
GS
MX
Mexico
TM
Turkmenistan
BJ
Benin
GT
S. Georgia and S. Sandwich
Isls.
Guatemala
MY
Malaysia
TN
Tunisia
BM
Bermuda
GU
Guam
MZ
Mozambique
TO
Tonga
BN
Brunei Darussalam
GW
Guinea-Bissau
NA
Namibia
TP
East Timor
BO
Bolivia
GY
Guyana
NC
New Caledonia
TR
Turkey
BR
Brazil
HK
Hong Kong
NE
Niger
TT
Trinidad and Tobago
BS
Bahamas
HM
Heard and McDonald Islands
NF
Norfolk Island
TV
Tuvalu
BT
Bhutan
HN
Honduras
NG
Nigeria
TW
Taiwan
BV
Bouvet Island
HR
Croatia (Hrvatska)
NI
Nicaragua
TZ
Tanzania
BW
Botswana
HT
Haiti
NL
Netherlands
UA
Ukraine
BZ
Belize
HU
Hungary
NO
Norway
UG
Uganda
CA
Canada
ID
Indonesia
NP
Nepal
UM
US Minor Outlying Islands
CC
Cocos (Keeling) Islands
IE
Ireland
NR
Nauru
US
United States
CF
Central African Republic
IL
Israel
NT
Neutral Zone
UY
Uruguay
CH
Switzerland
IM
Isle of Man
NU
Niue
UZ
Uzbekistan
CI
IN
India
NZ
Vatican City State (Holy See)
IO
British Indian Ocean Territory
OM
New Zealand
(Aotearoa)
Oman
VA
CK
Cote D'Ivoire (Ivory
Coast)Islands
Cook
VC
CL
Chile
IS
Iceland
PA
Panama
VE
Saint Vincent and the
Grenadines
Venezuela
CM
Cameroon
IT
Italy
PE
Peru
VG
Virgin Islands (British)
CN
China
JE
Jersey
PF
French Polynesia
VI
Virgin Islands (U.S.)
CO
Colombia
JM
Jamaica
PG
Papua New Guinea
VN
Viet Nam
CR
Costa Rica
JO
Jordan
PH
Philippines
VU
Vanuatu
CS
Czechoslovakia (former)
JP
Japan
PK
Pakistan
WF
Wallis and Futuna Islands
CV
Cape Verde
KE
Kenya
PL
Poland
WS
Samoa
CX
Christmas Island
KG
Kyrgyzstan
PM
St. Pierre and Miquelon
YE
Yemen
CY
Cyprus
KH
Cambodia
PN
Pitcairn
YT
Mayotte
CZ
Czech Republic
KI
Kiribati
PR
Puerto Rico
ZA
South Africa
DE
Germany
KM
Comoros
PS
Palestinian Territory
ZM
Zambia
DJ
Djibouti
KN
Saint Kitts and Nevis
PT
Portugal
COM
US Commercial
DK
Denmark
KR
Korea (South)
PW
Palau
EDU
US Educational
DM
Dominica
KW
Kuwait
PY
Paraguay
GOV
US Government
DO
Dominican Republic
KY
Cayman Islands
QA
Qatar
INT
International
DZ
Algeria
KZ
Kazakhstan
RE
Reunion
MIL
US Military
EC
Ecuador
LA
Laos
RO
Romania
NET
Network
EE
Estonia
LC
Saint Lucia
RS
Serbia
ORG
Non-Profit Organization
EG
Egypt
LI
Liechtenstein
RU
Russian Federation
ARPA
Old style Arpanet
EH
Western Sahara
LK
Sri Lanka
RW
Rwanda
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
110
www.netcommwireless.com
3.
When you have entered all the required details, press the Generate button. The certificate takes several minutes to
generate. When the certificate has been generated, you are informed that it has been successfully generated and installed.
The web server on the router restarts and you are logged out of the router. Click OK to be taken back to the login screen.
Figure 105 - New certificate successfully generated message
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
111
SSH Key Management
Secure Shell (SSH) is UNIX-based command interface and network protocol used to gain secure access to a remote computer,
execute commands on a remote machine or to transfer files between machines. It was designed as a replacement for Telnet and
other insecure remote shell protocols which send information, including passwords, as plain text.
SSH uses RSA public key cryptography for both connection and authentication. Two common ways of using SSH are:
Use automatically generated public-private key pairs to encrypt the network connection and then use password
authentication to log on.
Use a manually generated public-private key pair to perform the authentication and allow users or programs to log in
without using a password.
Figure 106 - SSH Server Configuration
SSH Server Configuration
To configure the SSH server settings:
1.
Use the SSH Protocol drop down list to select the protocol that you want to use. Protocol 2 is more recent and is
considered more secure.
2.
Select the types of authentication you want to use by clicking the Enable password authentication and Enable key
authentication toggle keys on or off. Note that you may have both authentication methods on but you may not turn them
both off.
3.
Click the Save button to confirm your settings.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
112
www.netcommwireless.com
Host key management
SSH keys provide a means of identification using public key cryptography and challenge response authentication. This means that a
secure connection can be established without transmitting a password, thereby greatly reducing the threat of someone
eavesdropping and guessing the correct credentials.
SSH Keys always come in pairs with one being a public key and the other a private key. The public key may be shared with any
server to which you want to connect. When a connection request is made, the server uses the public key to encrypt a challenge (a
coded message) to which the correct response must be given. Only the private key can decrypt this challenge and produce the
correct response. For this reason, the private key should not be shared with those who you do not wish to give authorization.
The Host key management section displays the current public keys on the router and their date and timestamp. These public keys
are provided in different formats, including DSA, RSA and ECDSA. Each format has advantages and disadvantages in terms of
signature generation speed, validation speed and encryption/decryption speed. There are also compatibility concerns to consider
with older clients when using ECDSA, for example.
Generating new keys
The complete set of keys can be re-generated by selecting the Generate keys button. This key generation process takes
approximately 30 seconds to complete.
Downloading keys
The Get keys button allows you to download the complete set of public and private keys while the Get public keys button will
download only the set of public keys.
Uploading your own key files
Click the Upload keys button to upload your own public key to the router.
Client key management
The Client Key Management section is used for uploading the public key file of clients. To upload a client public key, click the
Upload button, browse to the file and click Open.
When the file is uploaded, it is examined for validity. If the key file is not a valid public key, it will not be uploaded.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
113
LED operation mode
The LED indicators may be turned off after a timeout period for aesthetic or power saving reasons. To access the LED Operation
Mode page, click the System menu, then Administration on the left and finally select LED Operation Mode.
Figure 107 - LED Operation Mode
The Mode drop down list sets the operation mode of the LEDs on the front panel of the router. To set the lights to operate at all
times, set this to Always on. To set the lights to turn off after a specified period, select Turn off after timeout. When configured to
turn off after timeout, use the LED power off timer field to specify the time in minutes to wait before turning off the LED indicators.
The LED Power Off Timer must be an integer between 1 and 65535.
The wait period begins from the time the Save button is clicked. When the wait period expires, the LEDs will turn off. If the router is
rebooted, the LED power off timer is reset. The router will boot up and wait for the configured time before turning off again.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
114
www.netcommwireless.com
Reboot
The reboot option in the System section performs a soft reboot of the router. This can be useful if you have made configuration
changes you want to implement.
To reboot the router:
1.
Click the System menu item from the top menu bar.
2.
Click the Reboot button from the menu on the left side of the screen.
Figure 108 - Reboot menu option
3.
The router displays a warning that you are about to perform a reboot. If you wish to proceed, click the Reboot button then
click OK on the confirmation window which appears.
Figure 109 - Reboot confirmation
Note: It can take up to 2 minutes for the router to reboot.
Logging out
To log out of the router, click the
www.netcommwireless.com
icon at the top right corner of the web user interface.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
115
Appendix A: Tables
Table 1 - Document Revision History .........................................................................................................2
Table 2: Maximum Transmit Power Levels .................................................................................................5
Table 3 - LED Indicators ............................................................................................................................9
Table 4 - SIM Lock LED Statuses ............................................................................................................ 10
Table 5 - Device Dimensions.................................................................................................................... 11
Table 6 - Mounting Bracket Dimensions ................................................................................................... 11
Table 7 - Antenna Dimensions ................................................................................................................. 12
Table 8 - Bottom Mounted Integrated Interfaces ...................................................................................... 13
Table 9 - Top Mounted Interfaces ........................................................................................................... 14
Table 10 - Locking Power Block Pin Outs ................................................................................................ 17
Table 11 - Management account login details – Root manager ................................................................. 19
Table 12 - Management account login details – Admin manager............................................................... 19
Table 13 - Status page item details .......................................................................................................... 22
Table 14 - Data connection item details ................................................................................................... 24
Table 15 - Band settings.......................................................................................................................... 27
Table 16 - Wireless Configuration - Basic Configuration Items .................................................................. 38
Table 17 - Wireless Settings - Advanced Configuration Items ................................................................... 39
Table 18 - Current MAC / IP / Port filtering rules in effect .......................................................................... 55
Table 19 - IPSec Configuration Items ....................................................................................................... 58
Table 20 - SMS Setup Settings ................................................................................................................ 85
Table 21 - Inbox/Outbox icons ................................................................................................................. 87
Table 22 - SMS Diagnostic Command Syntax .......................................................................................... 92
Table 23 - List of basic SMS diagnostic commands ................................................................................. 93
Table 24 - List of get/set commands........................................................................................................ 94
Table 25 - List of basic SMS diagnostics RDB variables ........................................................................... 95
Table 26 - Network types returned by get plmnscan SMS command ........................................................ 95
Table 27 - Operator status codes returned by get plmnscan SMS command ............................................ 95
Table 28 - SMS diagnostics example commands ..................................................................................... 98
Table 29 - System log detail levels ......................................................................................................... 100
Table 30 - Administration configuration options ...................................................................................... 108
Table 31 - LAN Management Default Settings ........................................................................................ 117
Table 32 – WiFi Default Settings ............................................................................................................. 117
Table 33 - Web Interface Default Settings .............................................................................................. 117
Table 34 - Technical Specifications of the NTC-30WV routers ................................................................ 124
Table 35 - Additional Product Information - Call Feature Codes Quick Reference .................................... 126
Table 36 - List of Mobile Broadband Service Provider APNs ................................................................... 129
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
116
www.netcommwireless.com
Appendix B: Default Settings
The following tables list the default settings for the NTC-30WV.
LAN (MANAGEMENT)
Static IP Address:
192.168.1.1
Subnet Mask:
255.255.255.0
Default Gateway:
192.168.1.1
Table 31 - LAN Management Default Settings
WIRELESS (WIFI)
NetComm XXXX
SSID:
(where XXXX is a 4 digit random
number)
Security:
WPA2-PSK
XXXXXXXXXX
Security Key:
(where XXXXXXXXXX are 10 random
characters)
Table 32 – WiFi Default Settings
Note: For security purposes, we recommend that you change the Default SSID and Wireless Security Key.
ADMIN MANAGER ACCOUNT
Username:
admin
Password:
admin
ROOT MANAGER ACCOUNT
Username:
root
Password:
admin
Table 33 - Web Interface Default Settings
Note: The admin manager account allows you to manage most of the settings of the router except functions such as
Firmware Upgrade, Device Configuration Backup, Mobile Broadband Connection settings, and Reset to Factory Default
Settings, which are privileged only to the root manager account. First time users should use the root manager account to
configure Mobile Broadband settings.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
117
Restoring factory default settings
Restoring factory defaults will reset the NTC-30WV router to its factory default configuration. You may encounter a situation where
you need to restore the factory defaults on your NTC-30WV router such as:
You have lost your username and password and are unable to login to the web configuration page;
You are asked to perform a factory reset by support staff.
There are two methods you can use to restore factory default settings on your NTC-30WV router:
Using the web-based user interface
Using the reset button on the interface panel of the router
Using the web-based user interface
To restore your router to its factory default settings, please follow these steps:
1.
Open a browser window and navigate to the IP address of the router (default address is http://192.168.1.1). Login to the
router using root as the User Name and admin as the password.
2.
Click the System item from the top menu bar, then System configuration on the left menu and then click Settings backup
and restore.
3.
Under the Restore factory defaults section, click the Restore defaults button. The router asks you to confirm that you wish
to restore factory defaults. Click OK to continue. The router sets all settings to default. Click OK again to reboot the router.
4.
When the Power light returns to a steady red, the reset is complete. The default settings are now restored.
Using the reset button on the interface panel of the router
Use a pen to depress the Reset button on the device for more than 15 seconds. When the LEDs are no longer flashing, release the
reset button to restore the router to factory default settings. The red LED flashes indicating that you have initiated a factory reset
procedure. If you change your mind after holding the button down for more than 15 seconds, you can cancel the factory reset
process by disconnecting the power source while still holding the reset button down. Alternatively, you can release the reset button
and quickly press it once more.
When you have reset your NTC-30WV router to its default settings you will be able to access the device’s configuration web
interface using http://192.168.1.1 with username admin or root and password admin.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
118
www.netcommwireless.com
Appendix C: Recovery mode
The NTC-30WV Router features two independent operating systems, each with its own file systems. These two systems are
referred to as 'Main' and 'Recovery'. It is always possible to use one in order to restore the other in the event that one system
becomes damaged or corrupted (such as during a firmware upgrade failure). The recovery console provides limited functionality and
is typically used to restore the main firmware image in the case of a problem.
Accessing recovery mode
Both systems have web interfaces that can be used to manipulate the other inactive system. The NTC-30WV Router starts up by
default in the Main system mode, however the router may be triggered to start in recovery mode if desired.
To start the router in recovery mode:
1.
Press and hold the physical reset button on the interface panel of the router for 5 to 15 seconds. When the LEDs on the
front panel flash simultaneously, release the reset button. The router then boots into recovery mode.
2.
In your browser, navigate to http://192.168.1.1. The router’s recovery mode is hardcoded to use this address regardless
of the IP address that was configured in the main system. The router’s recovery console is displayed.
Figure 110 - Recovery console
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
119
Status
The status page provides basic information such as the system up time, hardware and software router versions, the router’s serial
number, the method used to trigger the recovery mode, the IP and MAC address of the router and the status of the Ethernet port.
Figure 111 - Recovery mode - Status
Log
The log page displays the system log which is useful in troubleshooting problems which may have led to the router booting up in
recovery mode. The only functionality provided here is the ability to clear the system log, filter by log level and downloading of the
log file.
Figure 112 - Recovery mode – Log
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
120
www.netcommwireless.com
Application Installer
The Application installer is designed to upload and install main firmware images, upload recovery firmware images, custom
applications and HTTPS certificates. Use the Browse button to select a file to be uploaded to the router. When it has been selected,
press the Upload button. The file is sent to the router and when the transfer is complete, the file appears in the Uploaded files list.
From the Uploaded files list, you are able to either Install or Delete a file.
Figure 113 - Recovery mode - Application Installer
Settings
The settings page provides the option of restoring the router to factory default settings. Click the Restore button to set the router
back to the original factory settings.
Figure 114 - Recovery mode – Settings
Reboot
The reboot page allows you to reboot the router when you have finished using recovery mode. When rebooting the router from
recovery mode, the router boots into the main firmware image unless there is some fault preventing it from doing so, in which case
the recovery console will be loaded.
Click the Reboot button to reboot the router to the main firmware image.
Figure 115 - Recovery mode - Reboot
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
121
Appendix D: HTTPS Uploading a self-signed
certificate
If you have your own self-signed certificate or one purchased elsewhere and signed by a Certificate Authority, you can upload it to
the NTC-30WV router using the Upload page.
Note: Your key and certificate files must be named server.key and server.crt respectively otherwise they will not work.
To upload your certificate:
1.
Click on the System item from the top menu bar. From the side menu bar, select System Configuration and then Upload.
The file upload screen is displayed.
Figure 116 - Upload page
2.
Click the Choose a File button and locate your server certificate file and click Open.
Figure 117 - Browse for server.crt
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
122
www.netcommwireless.com
3.
Click the Upload button to begin uploading it to the router. The file appears in the list of files stored on the router.
Figure 118 - Server certificate file uploaded
4.
Repeat steps 2 and 3 for the server key file.
5.
Click the Install link next to the server.crt file then click OK on the prompt that is displayed. The certificate file is installed.
Repeat this for the key file. When each file is installed it is removed from the list of stored files.
Figure 119 - Installing the server.crt file
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
123
Technical Data
The following tables list the hardware specifications of the NTC-30WV router.
COMPONENT
NTC-30WV
RAM
64MB DRAM
Memory
256MByte Flash memory storage
Wireless LAN
IEEE 802.11b/g/n, up to 16 concurrent users
Wireless Frequency
2.4 ~ 2.438Ghz
Peak Data Rate (Wireless)
300 Mbps (MIMO)
UMTS bands
UMTS/HSDPA/HSUPA: 850/900/1900/2100 MHz
GSM bands
GSM/GPRS/EDGE: 850/900/1800/1900 MHz
Maximum Data Throughput /
3G Radio interface
Downlink: 21 Mbps (HSPA Evolution); EDGE/GPRS 247Kbps); Uplink: Uplink: 5.76 Mbps (HSPA Evolution); EDGE/GPRS
236Kbps
1x Fast Ethernet 10/100Base-TX w/ Auto MDIX
Connectivity
1x Voice port (RJ-11)
1 x Circular IP67 Power Connection
SIM Card Reader
Antenna connectors
LED Indicators
Locking Tray for SIM/SIM in Mini-SIM card format (25.00 x 15.00 x 0.76 mm)
Cellular: 2 x detachable TNC (1 x Main and 1 x Rx Diversity)
WLAN: 2 x detachable TNC (1 x Main and 1 x Rx Diversity)
7 LEDs: Power, Network Service, 5 x Signal Strength
Normal Operating Temperature: -25 ˚C to 60 ˚C
Operating Temperature
Extended Operating Temperature:
Module: -25˚C to +75˚C (Reduced Performance)
DC-in Port: 9 ~ 28V
Power input
PoE (IEEE 802.3af): 48V DC
AC/DC Power Adapter: 100-240V AC to 12V DC/1.5A
Standby Input Current: 110mA @ 12V DC
Power Consumption
3G Active Current: 300mA @ 12V DC
Maximum Input Current: 560mA @ 12V DC
NTC-30WV: 255mm X 240mm X 80mm / 1750g
Dimensions & Weight
Mounting Bracket: 290mm X 110mm X 12mm / 410g
Antennas: length = 180mm; diameter = 20mm / 60g
Regulatory Compliancy
A-Tick (Australia), CE (Europe), FCC (USA), RoHS.
Table 34 - Technical Specifications of the NTC-30WV routers
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
124
www.netcommwireless.com
Additional Product Information
Using the NTC-30WV to make and receive telephone calls
The NTC-30WV provides circuit switched voice services via a telephony line interface offering the ability to make and receive
telephone calls via a regular analogue telephone using the 3G mobile network.
Note: Please refer to your mobile service provider for activation of your voice service and information about the call charges
that apply.
Handset requirements
The NTC-30WV allows you to make telephone calls over the 3G network using a standard analogue telephone via the built in RJ-11
Phone port. Please refer to the documentation provided by the manufacturer of your analogue telephone for assistance with the
operation of your telephone handset.
Maximum REN Loading
Please note that each of the line interfaces on the NTC-30WV is capable of supporting multiple analogue telephones connected via
splitters. The ringer equivalence number (REN) for each line is 5. Therefore, a maximum of 5 handsets each with a REN number of 1
can be connected to each line port.
Before you start making any phone calls, make sure you have checked the following:
You have an activated 3G SIM card inserted prior to powering on the NTC-30WV.
1.
Your NTC-30WV is powered on and in running condition.
2.
A working analogue telephone connected into the Line port.
3.
You hear the dial tone after lifting the handset.
How to place a call
To make a call, simply lift the handset and dial the number following the instructions provided by your telephone handset
manufacturer.
How to receive a call
When an incoming call is received, the phone connected to the NTC-30WV will ring. Answer the telephone following the instructions
provided by your telephone handset manufacturer to conduct the call.
If there is no phone connected to the NTC-30WV, all incoming calls will be transferred to Voicemail (if enabled on the device).
Answering an incoming call when on a call
Call waiting enables a 2nd incoming call to be received while you are on a call. To answer a call waiting call, perform a hook-flash
(clicking “flash” button, or briefly depressing the hook button) and then click button 2. The incoming call should then be answered.
Upon performing another hook-flash, waiting for 2 seconds and then clicking button 2, you will be returned to the original telephone
call.
Accessing voicemail
To access your voicemail, please dial *98 and follow the voice prompts.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
125
Call feature codes
Quick Reference Table
The NTC-30WV supports a number of call feature codes for supplementary services.
FEATURE
ACTIVATION
DEACTIVATION
STATUS
#31#
*31#
(to unblock caller ID for
outgoing calls)
(to block caller ID for outgoing
calls)
*#31#
*43#
#43#
*#43#
Call Forwarding Unconditional
*21*<Directory Number>#
#21#
*#21#
Call Forwarding No Answer
*61*<Directory Number>#
#61#
*#61#
Call Forwarding Busy
*24*<Directory Number>#
#24#
*#24#
*62*<Directory Number>#
#62#
*#62#
Caller ID
Call Waiting
Call Forwarding Unreachable
Table 35 - Additional Product Information - Call Feature Codes Quick Reference
Caller ID
Caller ID transmits a caller’s number to the called party’s telephone equipment when the call is being set up but before the call is
answered. Where available, caller ID can also provide a name associated with the calling telephone number.
To force Caller ID to be blocked for an outbound call, dial *31#, and hang up after you hear 2 low pitch beeps.
To force Caller ID to be unblocked for an outbound call, dial #31#, and hang up after you hear 2 high pitch beeps.
To check the status of Call Waiting, dial *#31#.
o
Caller ID is blocked if you hear 2 low pitch beeps.
o
Caller ID is unblocked if you hear 2 high pitch beeps.
Caller ID Test Steps
Dial *31#. Hang up and then out-call a mobile phone. The router phone’s number should be blocked;
4.
Dial #31#. Hang up and then out-call a mobile phone. The router phone’s number should be shown.
Call Waiting
Call waiting allows for indication and answering of an incoming telephone whilst an existing call is underway.
To disable call waiting, dial #43#, and hang up after you hear 2 high pitch beeps.
To enable call waiting, dial *43#, and hang up after you hear 2 low pitch beeps.
To check the status of Call Waiting, dial *#43# or view the advanced status page of the management console.
o
Call waiting is disabled if you hear 2 high pitch beeps.
o
Call waiting is enabled if you hear 2 low pitch beeps.
Call Forwarding
Call forwarding (or call diverting), is a features that allow an incoming call to be redirected to another number depending on the
circumstances at the time of receiving the call.
Note: Of the four Call forwarding features, the Unconditional feature has the highest priority. Once Call Forwarding
Unconditional is enabled, Call Forwarding No Answer, Call Forwarding Busy and Call Forwarding Unreachable are
disabled.
.
Call Forwarding Unconditional
Call forwarding Unconditional will divert all incoming calls to a phone number that you desire.
To enable Call Forwarding Unconditional, dial *21*<Directory Number>#
(Where directory number is the number you wish to forward calls to)
Hang up after you hear 2 low pitch beeps.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
126
www.netcommwireless.com
To disable Call Forwarding Unconditional, dial #21#
Hang up after you hear 2 high pitch beeps.
To check the status of Call Forwarding Unconditional, dial *#21# or view the advanced status page of the management
console.
o
Call Forwarding Unconditional is disabled if you hear 2 high pitch beeps.
o
Call Forwarding Unconditional is enabled if you hear 2 low pitch beeps.
Call Forwarding No Answer
Call forwarding No Answer will divert all incoming calls to a phone number that you desire only if the incoming call is not answered.
To enable Call Forwarding No Answer, dial *61*<Directory Number>#
(Where directory number is the number you wish to forward calls to)
Hang up after you hear 2 low pitch beeps.
To disable Call Forwarding No Answer, dial #61#
Hang up after you hear 2 high pitch beeps.
To check the status of Call Forwarding No Answer, dial *#61# or view the advanced status page of the management console. Call
Forwarding No Answer is disabled if you hear 2 high pitch beeps. Call Forwarding No Answer is enabled if you hear 2 low pitch
beeps.
Call Forwarding Busy
Call forwarding busy will divert all incoming calls to a phone number that you desire only if your telephone is busy on another call.
To enable Call Forwarding Busy, dial *24*<Directory Number>#
(Where directory number is the number you wish to forward calls to)
Hang up after you hear 2 low pitch beeps.
To disable Call Forwarding Busy, dial #24#
Hang up after you hear 2 high pitch beeps.
To check the status of Call Forwarding Busy, dial *#24# or view the advanced status page of the management
console.
o
Call Forwarding Busy is disabled if you hear 2 high pitch beeps.
o
Call Forwarding Busy is enabled if you hear 2 low pitch beeps.
Call Forwarding Not Reachable
Call forwarding not reachable will divert all incoming calls to a phone number that you desire only if your telephone is unreachable by
the network.
To enable Call Forwarding Not Reachable dial *62*<Directory Number>#
(Where directory number is the number you wish to forward calls to)
Hang up after you hear 2 low pitch beeps.
To disable Call Forwarding Not Reachable, dial #62#, Hang up after you hear 2 high pitch beeps.
To check the status of Call Forwarding Not Reachable, dial *#62# or view the advanced status page of the
management console.
o
Call Forwarding No Answer is disabled if you hear 2 high pitch beeps.
o
Call Forwarding No Answer is enabled if you hear 2 low pitch beeps.
Conference Call
This can be achieved by performing the following:
From the phone connected to the router, make a call to the 1st phone. Afterward perform a hook-flash (click “flash” button, or
briefly depressing the hook button) to put the 1st call on hold.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
127
Call the 2nd phone number. After the 2nd phone picks up the call, place both calls into one conference call by performing
another hook-flash and then pressing button 3.
5.
To terminate the conference call hang up the phone connected to the router.
Voice Troubleshooting
What do I do if I have no dial tone?
Please follow the procedure listed below:
Check to make sure the phone is plugged into your NTC-30WV on the RJ-11 port (between the power socket and the LAN
port).
6.
Check to make sure you are using the correct cable (Cat-3 UTP Telephone Cable with RJ-11 plugs).
7.
Check to make sure the “SIM status” shows “SIM OK” on the Status page of the Web interface.
8.
Check to make sure your 3G SIM card is activated and insert into your NTC-30WV properly.
9.
Check and see if you get the dial tone after rebooting your NTC-30WV.
I have noise interference during telephone calls. How can I fix this?
To resolve this issue, try the following:
Verify that the RJ-11 cable is securely connected and not damaged.
10. Try to remove any telephone splitters from the connection between your phone and theNTC-30WV.
11. Try rebooting your NTC-30WV.
List of Mobile Broadband Service Provider APNs
MOBILE SERVICE
APN
Australia
Telstra
telstra.internet
Optus – Postpaid
connect
Optus – Prepaid
preconnect
Three – Postpaid
3netaccess
Three – Prepaid
3services
Vodafone – Postpaid
vfinternet.au
Vodafone – Prepaid
vfprepaymbb
Crazy John’s
purtona.net
DoDo
dodolns1
Blink
splns888a1
Internode
Internode
Primus
primuslns1
TPG
internet
Exetel
Exetel1
Westnet
Splns555a1
iiNet
iiNet
New Zealand
Vodafone NZ
www.vodafone.net.nz
CallPlus
www.callplus.net.nz
Slingshot
www.slingshot.net.nz
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
128
www.netcommwireless.com
Telstra Clear
www.telstraclear.net.nz
Telecom NZ XT
wap.telecom.co.nz
2 Degrees
internet
Table 36 - List of Mobile Broadband Service Provider APNs
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
129
Legal & Regulatory
Information
Intellectual Property Rights
All intellectual property rights (including copyright and trade mark rights) subsisting in, relating to or arising out this Manual are
owned by and vest in NetComm Wireless (ACN 002490486) (NetComm Wireless Limited) (or its licensors). This Manual does not
transfer any right, title or interest in NetComm Wireless Limited’s (or its licensors’) intellectual property rights to you.
You are permitted to use this Manual for the sole purpose of using the NetComm Wireless product to which it relates. Otherwise no
part of this Manual may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic,
mechanical, recording or otherwise, without the prior written permission of NetComm Wireless Limited.
NetComm, NetComm Wireless and NetComm Wireless Limited are a trademark of NetComm Wireless Limited. All other trademarks
are acknowledged to be the property of their respective owners.
Customer Information
The Australian Communications & Media Authority (ACMA) requires you to be aware of the following information and warnings:
1.
This unit may be connected to the Telecommunication Network through a line cord which meets the requirements of the
AS/CA S008-2011 Standard.
2.
This equipment incorporates a radio transmitting device, in normal use a separation distance of 20cm will ensure radio
frequency exposure levels complies with Australian and New Zealand standards.
3.
This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACMA.
These standards are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio noise and, if not installed and used in accordance with the
instructions detailed within this manual, may cause interference to radio communications. However, there is no guarantee
that interference will not occur with the installation of this product in your home or office. If this equipment does cause
some degree of interference to radio or television reception, which can be determined by turning the equipment off and on,
we encourage the user to try to correct the interference by one or more of the following measures:
i.
ii.
4.
Change the direction or relocate the receiving antenna.
Increase the separation between this equipment and the receiver.
iii.
Connect the equipment to an alternate power outlet on a different power circuit from that to which the
receiver/TV is connected.
iv.
Consult an experienced radio/TV technician for help.
The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply
with any other product or do not use any other power supply that is not approved for use with this product by NetComm
Wireless. Failure to do so may cause damage to this product, fire or result in personal injury.
Consumer Protection Laws
Australian and New Zealand consumer law in certain circumstances implies mandatory guarantees, conditions and warranties which
cannot be excluded by NetComm and legislation of another country's Government may have a similar effect (together these are the
Consumer Protection Laws). Any warranty or representation provided by NetComm is in addition to, and not in replacement of, your
rights under such Consumer Protection Laws.
If you purchased our goods in Australia and you are a consumer, you are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you purchased our goods in New
Zealand and are a consumer you will also be entitled to similar statutory guarantees.
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
130
www.netcommwireless.com
Product Warranty
All NetComm Wireless products have a standard one (1) year warranty from date of purchase, however, some products have an
extended warranty option (refer to packaging and the warranty card) (each a Product Warranty). To be eligible for the extended
warranty option you must supply the requested warranty information to NetComm Wireless Limited within 30 days of the original
purchase date by registering online via the NetComm Wireless web site at www.netcommwireless.com. For all Product Warranty
claims you will require proof of purchase. All Product Warranties are in addition to your rights and remedies under applicable
Consumer Protection Laws which cannot be excluded (see Consumer Protection Laws Section above).
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see the Consumer
Protection Laws Section above), the Product Warranty is granted on the following conditions:
1.
the Product Warranty extends to the original purchaser (you / the customer) and is not transferable;
2.
the Product Warranty shall not apply to software programs, batteries, power supplies, cables or other accessories
supplied in or with the product;
3.
the customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable
requirements of NetComm including producing such evidence of purchase as NetComm may require;
4.
the cost of transporting product to and from NetComm’s nominated premises is your responsibility;
5.
NetComm Wireless Limited does not have any liability or responsibility under the Product Warranty where any cost, loss,
injury or damage of any kind, whether direct, indirect, consequential, incidental or otherwise arises out of events beyond
NetComm’s reasonable control. This includes but is not limited to: acts of God, war, riot, embargoes, acts of civil or
military authorities, fire, floods, electricity outages, lightning, power surges, or shortages of materials or labour; and
6.
the customer is responsible for the security of their computer and network at all times. Security features may be disabled
within the factory default settings. NetComm Wireless Limited recommends that you enable these features to enhance
your security.
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see Section 3 above),
the Product Warranty is automatically voided if:
1.
you, or someone else, use the product, or attempt to use it, other than as specified by NetComm Wireless Limited;
2.
the fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power
supply or communication line, whether caused by thunderstorm activity or any other cause(s);
3.
the fault is the result of accidental damage or damage in transit, including but not limited to liquid spillage;
4.
your product has been used for any purposes other than that for which it is sold, or in any way other than in strict
accordance with the user manual supplied;
5.
your product has been repaired or modified or attempted to be repaired or modified, other than by a qualified person at a
service centre authorised by NetComm Wireless Limited; or
6.
the serial number has been defaced or altered in any way or if the serial number plate has been removed.
Limitation of Liability
This clause does not apply to New Zealand consumers. Subject to your rights and remedies under applicable Consumer Protection
Laws which cannot be excluded (see the Consumer Protection Laws Section above), NetComm Wireless Limited accepts no liability
or responsibility, for consequences arising from the use of this product. NetComm Wireless Limited reserves the right to change the
specifications and operating details of this product without notice.
If any law implies a guarantee, condition or warranty in respect of goods or services supplied, and NetComm Wireless’s liability for
breach of that condition or warranty may not be excluded but may be limited, then subject to your rights and remedies under any
applicable Consumer Protection Laws which cannot be excluded, NetComm Wireless’s liability for any breach of that guarantee,
condition or warranty is limited to: (i) in the case of a supply of goods, NetComm Wireless Limited doing any one or more of the
following: replacing the goods or supplying equivalent goods; repairing the goods; paying the cost of replacing the goods or of
acquiring equivalent goods; or paying the cost of having the goods repaired; or (ii) in the case of a supply of services, NetComm
Wireless Limited doing either or both of the following: supplying the services again; or paying the cost of having the services
supplied again.
To the extent NetComm Wireless Limited is unable to limit its liability as set out above, NetComm Wireless Limited limits its liability
to the extent such liability is lawfully able to be limited.
www.netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice /
131
Contact
Address: NETCOMM WIRELESS LIMITED Head Office
PO Box 1200, Lane Cove NSW 2066 Australia
Phone: +61(0)2 9424 2070
Fax: +61(0)2 9424 2010
Email: sales@netcommwireless.com techsupport@netcommwireless.com
NetComm Wireless NTC-30WV 3G Outdoor Router with Voice
132
www.netcommwireless.com