Asus CP220 Series User guide

CP220 / CP240 Series
Zero client display
User Guide
Table of contents
Notices.......................................................................................................... iv
Safety information........................................................................................ v
Care and cleaning........................................................................................ vi
1.1Welcome........................................................................................ 1-1
ii
1.2
Package contents.......................................................................... 1-1
1.3
Assembling the base of the display............................................ 1-2
1.4
Display introduction..................................................................... 1-3
1.4.1
Front of the display.......................................................... 1-3
1.4.2
Rear of the display........................................................... 1-4
1.4.3
Get start with client system.............................................. 1-5
1.4.4
Client Indicator Behavior.................................................. 1-5
2.1
Detaching the arm/stand (for wall mounting)............................. 2-1
2.2
Adjusting the display.................................................................... 2-2
3.1
OSD (On-Screen Display) menu.................................................. 3-1
3.1.1
How to reconfigure........................................................... 3-1
3.1.2
OSD Function Introduction............................................... 3-1
3.2
Client setting................................................................................. 3-5
3.3
Specifications.............................................................................. 3-11
3.4
Trouble shooting (FAQ).............................................................. 3-12
3.5
Supported Timing List................................................................ 3-13
Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
As an Energy Star® Partner, our company has determined
that this product meets the Energy Star® guidelines for
energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
Warning: This client complies with the EMC directive only when you use a
shielded Ethernet cable.
iv
Safety information
Use only the AC/DC adapter model: EXA1203YH
• Before setting up the display, carefully read all the documentation that
came with the package.
• To prevent fire or shock hazard, never expose the display to rain or
moisture.
• Never try to open the display cabinet. The dangerous high voltages
inside the display may result in serious physical injury.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or
over a radiator or heat source unless proper ventilation is provided.
• The display should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supply to
your home, consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power
standard.
• Do not overload power strips and extension cords. Overloading can
result in fire or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the
display in any area where it may become wet. Place the display on a
stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a
long period of time. This will protect the display from damage due to
power surges.
• Never push objects or spill liquid of any kind into the slots on the
display cabinet.
• To ensure satisfactory operation, use the display only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC.
• The socket-outlet shall be installed near the equipment and shall be
easily accessible.
• If you encounter technical problems with the display, contact a qualified
service technician or your retailer.
v
Care and cleaning
• Before you lift or reposition your display, it is better to disconnect the
cables and power cord. Follow the correct lifting techniques when
positioning the display. When lifting or carrying the display, grasp the
edges of the display. Do not lift the display by the stand or the cord.
• Cleaning. Turn your display off and unplug the power cord. Clean the
display surface with a lint-free, non-abrasive cloth. Stubborn stains
may be removed with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner
intended for use with the screen. Never spray cleaner directly on the
screen, as it may drip inside the display and cause an electric shock.
The following symptoms are normal with the display:
• The screen may flicker during the initial use due to the nature of the
fluorescent light. Turn off the power switch and turn it on again to make
sure that the flicker disappears.
• You may find slightly uneven brightness on the screen depending on
the desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the
previous screen may remain after switching the image. The screen will
recover slowly or you can turn off the power switch for hours.
• When the screen becomes black or flashes, or cannot work anymore,
contact your dealer or service center to fix it. Do not try to repair the
display by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a
task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation that may
have been added by your dealer. These documents are not part of
the standard package.
vii
1.1Welcome
Thank you for purchasing the ASUS® display.
The latest display from ASUS provides a crisper, broader, and brighter
screen, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the display brings you!
1.2
Package contents
Check your package for the following items:
Display set
Display base and screw
Quick start guide
Warranty card
Power cord
Adapter
DVI Cable
VGA Cable
•
1-1
If any of the above items is damaged or missing, contact your retailer
immediately..
Chapter 1: Product Introduction
1.3
Assembling the base of the display
1.
Attach the base to the arm and fix with the screw to join them tightly.
You can easily tighten the screw by fingers.
2.
Adjust the monitor to the angle that is most comfortable for you.
2
1
•
We recommend that you cover the table surface with soft cloth to prevent from
damaging the display.
ASUS LCD Monitor CP220/CP240 Series
1-2
1.4
Display introduction
1.4.1
Front of the display
LED1 LED2
1.
Client LED Indicator:
•
2.
Power Indicator:
•
1-3
The color of client LED Indicator is as below.
The color of power indicator is as below.
Status
description
LED1
White
client power on
LED1
Amber
Power Off and Wake
On Lan/ Wake On USB
LED2
White
link to virtual desktop
Chapter 1: Product Introduction
1.4.2
Rear of the display
9
10
11
6
12
USB
1
2
3
4 5
1.
RJ45
2.
DVI connector
3.
VGA connector
4.
Microphone input
5.
audio-in jack
6.
earphone-out
7.
USB connector
8.
Power-in jack
9.
Screw holes of mounting interface
7
8
10. USB connector
11. Kensington lock
12. Control keypad
ASUS LCD Monitor CP220/CP240 Series
1-4
1.4.3
Item
Get start with client system
Key
Power
Input select
Description
Press this button to turn on/off the monitor
Press to select different input source
Brightness & Up
MENU
Menu
Volume & down
A
Auto adjust &
return
Link(LED)
Auto Adjust/Return to previous selection
Link to server
LED in white while client is on
LED in amber while client is off/wake-on-LAN or
wake-on-USB is enabled
Client(LED)
key
brightness/press to increase the numerical value of
selected function
Press to enter OSD menu
volume/press to decrease the numerical value of
selected function
Source Function
Description
in VGA source(>2 seconds)
in VGA source for short press.
Splendid mode switch
(<2 seconds)
Press shortly under login UI(<2
Instant connection
*Auto
seconds)
Adjust &
Exit OSD, press shortly
Return
to select disconnection, Press shortly under host
Client
turn off workstation or session(<2 seconds)
cancel
Disconnect and return Press shortly under server
to log in UI
session(<2 seconds)
VGA
1.4.4
Auto Adjustment
Client Indicator Behavior
Status
Power On
Power Off
Power On and Link to
Virtual Desktop
Power Off and Wake
On Lan
Power Off and Wake
On USB
POWER
White
Off
LINK
Off
Client
White
Off
Off
White
White
White
Amber
Off
Amber
Amber
Off
Amber
White(on
White (Blink
Power On to Power Off
12s then off)/
for 12s
and Wake On USB
Amber(always on) then off)
1-5
White (Blink 12s then off)
/ Amber (always on)
Chapter 1: Product Introduction
2.1
Detaching the arm/stand (for wall mounting)
To detach the arm/stand.
1.
Disconnect power and signal cables. Carefully put the front of the
monitor face down on a clean table.
2.
Use your fingers gently pull away the plate that covers the stand
neck. Use a screwdriver to remove the four screws that secure the
stand to the monitor.
3.
Detach the stand from the monitor.
•
We recommend that you cover the table surface with soft cloth to prevent from
damaging the display.
•
Hold the stand while removing the screws.
1
2
3
•
The (100 x 100 mm) wall mount kit is not included in the product purchased.
•
Use only the UL listed wall mount bracket with minimum weight/load 14kg
(Screw size: M4 x 10 mm).
ASUS LCD Monitor CP220/CP240 Series
2-1
2.2
Adjusting the display
• For optimal viewing, we recommend that you look at the full face of
the display, and then adjust the display to the angle that is the most
comfortable to you.
• Hold the stand to prevent the display from falling while changing its
angle.
• You may adjust the display’s angle from -5˚ to 23˚.
-5 ~ 23
2-2
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
CP220
Splendid
Scenery Mode
Color
Standard Mode
Picture
Theater Mode
Input Select
Game Mode
Menu
Night View Mode
sRGB
Move
OK
Exit
1.
Press the MENU button to activate the OSD menu.
2.
Press  and  button to navigate through the functions. Press
the OK button to highlight and activate the desired function. If the
selected function has a sub-menu, press and  button again to
navigate through the sub-menu. Press the OK button to highlight and
activate the desired sub-menu function.
3.
Press  and  button to change the settings of the selected function.
4.
To exit from the OSD menu, press the MENU button. Repeat step 2
and step 3 to adjust any other function.
3.1.2
OSD Function Introduction
1.Splendid
This function contains six sub-functions that you can select for your
preference. Each mode has the Reset selection, allowing you to
maintain your setting or return to the preset mode.
CP220
Splendid
Scenery Mode
Color
Standard Mode
Picture
Theater Mode
Input Select
Game Mode
Menu
Night View Mode
sRGB
Move
OK
Exit
•
Scenery Mode:This is the best choice for scenery photo displaying with
SPLENDID™ Video Intelligence.
•
Standard Mode: This is the best choice for document editing with
SPLENDID™ Video Intelligence.
ASUS LCD Monitor CP220/CP240 Series
3-1
•
Theater Mode: This is the best choice for movie watching with
SPLENDID™ Video Intelligence.
•
Game Mode: This is the best choice for game playing with SPLENDID™
Video Intelligence.
•
Night View Mode: This is the best choice for playing dark-scene game or
watching movie with SPLENDID™ Video Intelligence.
•
sRGB: This is the best choice for viewing photos and graphics from PCs.
•
In the User Mode of the Color Temp., the user may configure the value of the
prime color R (red), G (green), and B (blue) ranging from 0 to 100.
2. Color
Select the image color you like from this function.
CP220
Splendid
Brightness
Color
Contrast
Picture
ASCR
100
80
OFF
Input Select
Saturation
Menu
Color Temp.
50
User Mode
18
Gamma
Move
3-2
OK
Exit
•
Brightness: The adjusting range is from 0 to 100. The
also a hot key to activate this function.
•
Contrast:The adjusting range is from 0 to 100.
•
ASCR: To adjust the horizontal (H-Position) and the vertical position
(V-Position) of the image from the VGA input. The adjustable range is
from 0 to 100.
•
Saturation: The adjusting range is from 0 to 100.
•
Color Temp.: There are three preset white balance modes (D50, D65,
and 9300K) and one User mode.
•
Gamma:To alter the grayscale gamma between 18/2.2/2.5.
button is
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
Chapter 3: General Instruction
3.Picture
You may adjust the Aspect Control, Over Scan, Position (VGA only),
and Focus (VGA only) in this menu item.
CP220:
CP220
Splendid
Sharpness
Color
Aspect Control
Picture
Position
Input Select
Focus
50
Full
Menu
Move
OK
Exit
CP240:
CP240
Splendid
Sharpness
Color
Trace Free
Picture
Aspect Control
Input Select
Position
Menu
Focus
Move
OK
40
60
Full
Exit
•
Sharpness:Adjust the picture sharpness. The adjusting range is
from 0 to 100.
•
Trace free:speed up the response time by Over Drive technology.
The adjusting range is from lower 0 to faster 100.(Only for CP240)
•
Aspect Control:Adjust the aspect ratio to “Full”, “4:3”.
•
Position: Adjust the horizontal position (H-Position) and the
vertical position (V-Position) of the image. The adjusting range is
from 0 to 100 (only available for VGA input).
•
Focus:Reduce Horizontal-line noise and Vertical-line noise of the
image by adjusting (Phase) and (Clock) separately. The adjusting
range is from 0 to 100 (only available for VGA input).
ASUS LCD Monitor CP220/CP240 Series
3-3
4.
Input Select
5. Select the input source from VGA, client source input signal.
CP220
Splendid
VGA
Color
Client
Picture
Input Select
Select
Input
Menu
Move
OK
Exit
5.Menu
Adjusts the system configuration.
CP220
Splendid
OSD Setup
Color
Information
Picture
Language
Input Select
All Reset
English
Menu
Move
3-4
OK
Exit
•
OSD Setup:To adjust the OSD Timeout, DDC/CI, Transparency, and
Power indicator.
•
Information: To show the information of the display.
•
Language: To select OSD language. The selections are: English, French,
German, Spanish, Italian, Dutch, Russian, Traditional Chinese, Simplified
Chinese, Japanese, Persian, Thai, Indonesian, Poland, Turkey, Portugal,
Czech, Croatia, Hungary, Romania, and Korean.
•
All Reset: Selecting “Yes” to revert all settings back to the factory default
values.
Chapter 3: General Instruction
3.2
Client setting
1. Turn on power and press
to select [Client] as your input source.
Client
MENU:Exit
2. Login Client widget, click “[Options]“ on top left corner.
Options
3. Select “[Options]” --> “[Configuration]”.
Options
Configuration
Diagnostics
Information
User Settings
ASUS LCD Monitor CP220/CP240 Series
3-5
4. Enter “[Configuration]” --> [Network],and select “Enable DHCP”.
Configuration
Network IPv6 SCEP Label Discovery Session Language Power Display Access Audio Reset
Change the network settings for the device
Enable DHCP:
IP Address:
192 . 168 . 100 . 51
Subnet Mask:
255 . 255 . 255 . 0
Gateway:
192 . 168 . 100 . 1
Primary DNS Server:
192 . 168 . 100 . 2
Secondary DNS Server:
0
. 0
.0
.0
Domain Name:
FQDN:
Auto
Ethernet Mode:
Enable 802.1X Security:
Identity:
Client Certificate:
OK
Cancel
Apply
5. Select [Session] sheet and enter “DNS Name or IP Address”, then click
“Apply” to execute.
Configuration
Network IPv6 SCEP Label Discovery Session Language Power Display Access Audio Reset
vmware Horizon View Client
TM
Configure the connection to a peer device
Connection Type:
DNS Name or IP Address:
View Connection Server
192.168.100.252
Advanced
OK
3-6
Cancel
Apply
Chapter 3: General Instruction
6. Select [Language] sheet ,and choice requisite language, then click
“Apply” to execute.
Configuration
Network IPv6 SCEP Label Discovery Session Language Power Display Access Audio Reset
Select language for the user interface
Language:
Keyboard Layout:
English
US
OK
Cancel
Apply
7. Select [OK] to finish [Configuration].
8. Return to main manual, select [Options] on top left corner and go to
[User settings].
Options
Configuration
Diagnostics
Information
User Settings
ASUS LCD Monitor CP220/CP240 Series
3-7
9. Select [Certificate] sheet, choice item and setting, then click [OK].
User Settings
Certificate Mouse Keyboard Image
Display Topology Touch Screen
vmware Horizon View Client
TM
Certificate Checking Mode:
This mode determines how the client proceeds when it cannot verify that
your connection to the server is secure. It is not recommended that you
change this setting unless instructed to do so by your system administrator.
Never connect to untrusted servers
Warn before connecting to untrusted servers
Do not verify server identity certificates
OK
Cancel
Apply
10.Link to server IP and enter connection interface, Click [Connect].
Enter the address of the View
Connection Server.
Server:
192.168.100.252
Connect
3-8
Chapter 3: General Instruction
11.Enter “User name” and “password”, then click [Login].
https://192.168.100.252
Enter your user name and password
User name:
Password:
Server:
192.168.100.252
Login
Cancel
12.Click [Connect].
win7
Connect
Log on to desktop
Reser VM
Cancel
13.Enter client interface.
ASUS LCD Monitor CP220/CP240 Series
3-9
14. Select desktop “Start”, choice “Logout” to exit client.
3-10
Chapter 3: General Instruction
3.3
Specifications
Model
CP220
CP240
Panel Size
21.5” (54.61 cm)
23.8” (60.47 cm)
Max. Resolution
1920 x 1080
1920 x 1080
Brightness (Typ.)
250cd/m
250cd/m2
Intrisinc Contrast Ratio (Typ.)
2
1000:1
1000:1
160°(V); 170°(H)
178°(V); 178°(H)
16.7 M
16.7 M
Response Time (Typ.)
5ms
5ms (G to G)
D-Sub input
Yes
Yes
Viewing Angle (CR≧0)
Display Colors
Power ON Consumption
ON Mode: <50 W*
ON Mode: <50 W*
*Based on Energy Star 6.0
standard
*Based on Energy Star 6.0
standard
Speaker
Yes
Yes
Mic phone
Yes
Yes
Earphone
Yes
Yes
Note
Power saving mode
Power off mode
Tilt
<6W
<6W
< 0.5 W
< 0.5 W
-5° to +23°
-5° to +23°
100mm x 100mm
100mm x 100mm
523.2 x 497.0 x 224.8 mm
567.60 x 517.15 x 244.81
mm
654 x 397 x 176 mm
685 x 421 x 179 mm
Net Weight (Esti.)
5.3 kg
6.0 kg
Gross Weight (Esti.)
7.6 kg
8.5 kg
AC 100~240V(External)
AC 100~240V(External)
Mounting Interface
Phys. Dimension (WxHxD)
Box Dimension (WxHxD)
Voltage Rating
Processor
SCALER TERA2321 FCBGA-396
ROM
FLASH MX25L25635FMI-10G 256MB SOP-16
RAM
DRAM H5TQ2G63D(F)FR-H9C/MT41J128M16JT-107G-K
2Gb x 2
Client solution
ASUS LCD Monitor CP220/CP240 Series
Vmware
3-11
3.4
Trouble shooting (FAQ)
Problem
Power LED is not ON
Possible Solution
• Press the button to check if the monitor is in the
ON mode.
• Check if the power cord is properly connected to
the monitor and the power outlet.
• Check if the monitor and the computer are in the
ON mode.
• Make sure the signal cable is properly connected
the monitor and the computer.
The power LED lights amber and
• Inspect the signal cable and make sure none of the
there is no screen image
pins are bent.
• Connect the computer with another available
monitor to check if the computer is properly
working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings via
OSD.
Screen image is not centered or
sized properly
• Press the A
button for two seconds to
automatically adjust the image.
• Adjust the H-Position or V-Position settings via
OSD.
• Make sure the signal cable is properly connected to
Screen image bounces or a wave
the monitor and the computer.
pattern is present in the image
• Move electrical devices that may cause electrical
interference.
Screen image has color defects
(white does not look white)
• Inspect the signal cable and make sure that none of
the pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the Color
Temperature via OSD.
Screen image is blurry or fuzzy
• Press the
button for two seconds to
automatically adjust the image (for VGA mode
only).
• Adjust the Phase and Clock settings via OSD.
No sound or sound is low
• Make sure the audio cable is properly connected
to the display
• Adjust the volume settings of both your display and
computer.
• Make sure the computer sound card driver is
properly installed and activated.
A
3-12
Chapter 3: General Instruction
3.5
Supported Timing List
VESA / IBM Modes Support timing (D-SUB inputs)
Resolution
640 x 350
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
848 x 480
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 720
1280 x 800
1280 x 960
1280 x 1024
1280 x 1024
1366 x 768
1440 x 900
1680 x 1050
1680 x 1050
1920 x 1080
1920 x 1080
Refresh Rate
70Hz
60Hz
67Hz
75Hz
70Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
Horizontal Frequency
31.469KHz
31.469KHz
35KHz
37.5KHz
31.469KHz
35.156KHz
37.879KHz
48.077KHz
46.875KHz
31.02KHz
48.363KHz
56.476KHz
60.023KHz
67.5KHz
44.772KHz
49.702KHz
60KHz
63.981KHz
79.976KHz
47.712KHz
55.935KHz
65.29KHz
64.674KHz
67.5KHz
66.587KHz
* The modes not listed in the above tables may not be supported. For an optimal resolution, we
recommend that you choose a mode listed in the above table.
ASUS LCD Monitor CP220/CP240 Series
3-13