USB2
(HDD)
USB1
For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note that many digital cable programs are not in HD. Check
with your video provider to ensure your are receiving HD signals.
STOP
AV IN 2
Analog Audio connection
LN32C530 / LN37C530 / LN40C530 / LN46C530
Device
HDMI OUT
Amplifier / DVD Home Theater
HDMI IN 4
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
Digital Audio connection
(HDD)
USB1
The HDMI connection carries
digital video and audio.
Using an Optical Cable
AV IN 2
USB2
Best Connection
Digital Audio System
OPTICAL
HDMI IN 4
HD connection (up to 1080p)
Follow the steps below to connect the TV to the stand.
DVI OUT
USB2
Stand when assembling them.
✎✎ Make sure that at least two people lift and move the LCD TV.
✎✎ Stand the product up and fasten the screws. If you fasten the screws with the
LCD TV placed down, it may lean to one side.
(HDD)
USB1
Using an DVI to HDMI Cable
✎✎ Make sure to distinguish between the front and back of the Stand and Guide
AV IN 2
Device
DVD / Blu-Ray player /
Cable Box /
Satellite receiver (STB)
HDMI IN 4
AUDIO OUT
(HDD)
USB1
Very Good Connection
AV IN 2
2
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
LN32C530 / LN37C530 / LN40C530 / LN46C530
Component connection (up to 1080p)
Stand
Using a Component Cable
Front
AUDIO OUT
HD connection
Device
COMPONENT OUT
Using an HDMI Cable
s
s
s
s
Rear
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Audio/Video connection (480i only)
Bottom View
s
s
s
Top View
s
Using an Audio/Video Cable
VIDEO OUT
VCR
AUDIO OUT
attach the video cable (yellow) to the green jack next
to the AV In 1 label. The jack will not match the color
of the video cable (yellow).
Lowest Quality Connection
s
s
s
PC
HDMI IN 4
s
DVI OUT
Good Connection
✎✎ When connecting to AV 1 on the back of your TV,
(HDD)
USB1
3
AUDIO OUT
USB2
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Screw
Device
AUDIO IN
Using an HDMI Cable
Step 1 : Install the Stand
Guide Stand
Using an Audio Cable
HD connection (up to 1080p)
Getting Started
1
AV IN 2
Connect your TV to your Home Theater or other audio device to enjoy enhanced sound
quality.
USB2
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit:
www.samsung.com/register.
(HDD)
USB1
Connecting an audio device
HDMI IN 4
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
HDMI IN 4
USB2
Step 4 : Connect External Devices
Quick Setup Guide
Using an D-Sub Cable
AV IN 2
LN40C540 / LN46C540
PC OUT
AUDIO OUT
HD connection (up to 1080p)
USB2
Step 2 : Install the Batteries into the Remote
Install two AAA batteries.
Best Connection
HDMI IN 4
HD connection (up to 1080p)
✎✎ Make sure to match the + and - ends of
the batteries to the diagram in the battery
compartment.
DVI OUT
Replace the cover.
AV IN 2
AUDIO OUT
HDMI IN 4
Step 3 : Connect Power and Antenna or Cable
(HDD)
USB1
Using an DVI to HDMI Cable
USB2
3.
LN40C540 / LN46C540
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
AV IN 2
USB2
2.
Device
(HDD)
USB1
Lift the cover on the back of the remote upward
as shown in the figure to the right.
HDMI IN 4
HDMI OUT
To install batteries into your remote control, follow these steps:
1.
PC
Using an HDMI Cable
HD connection
Using an HDMI Cable
AUDIO OUT
DVI OUT
PC
Device
DVD / Blu-Ray player /
Cable Box /
Satellite receiver (STB)
(HDD)
USB1
Very Good Connection
Using an D-Sub Cable
AV IN 2
Component connection (up to 1080p)
Connect Ant In to:
or
Power Input
Use a 75 ohm (round) cable.
• Wall cable jack or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Using a Component Cable
AUDIO OUT
Using an Audio/Video Cable
Make sure the AC power cord
is plugged in securely to the
wall outlet and the TV.
AUDIO OUT
VCR
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Device
AUDIO OUT
PC
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Audio/Video connection (480i only)
VIDEO OUT
COMPONENT OUT
PC OUT
Good Connection
✎✎ When connecting to AV1 on the back of your TV,
attach the video cable (yellow) to the green jack next to
the AV In 1 label. The jack will not match the color of
the video cable (yellow).
Lowest Quality Connection
English - 1
BN68-02610A-Eng.indd 1
2010-02-11 �� 11:30:25
Step 5 : Run Plug & Play
Changing the Screen Size
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process. It also
displays connection instructions similar to those in this guide.
PRE-CH
After you have selected the cable system type, select Start, and then
press the EnterE button on your remote.
✎✎ Most cable systems are Standard (STD) systems. If you are not sure
about what kind of cable system you have, contact your cable company.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the EnterE
button. To skip a screen, press the Menu button.
5.
To turn on your TV, press the Power button on the remote or press the
Power button on the TV. To run Plug & Play, follow these steps:
The TV memorizes the available channels. This process can take up to 45
minutes. After the TV has memorized the channels, the Clock Mode screen
appears.
6.
Choose the Clock Mode. Select Auto if you have a digital channel in your
area. Select Manual if you don’t, or if you have a cable or satellite box. When
done, press EnterE button. The Daylight Savings screen appears.
Plug & Play
Select Language of the OSD.
Language
2.
3.
7.
Español
: English
Français
On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press EnterE button. The
Home Use screen appears.
Select Home Use, and then press EnterE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press EnterE button, the Antenna Source screen appears.
CHLIST
MENU
INFO
RETURN
8.
After the time zone screen, The connection method for best HD screen quality
is displayed. Press Right arrow button on your remote to view each screen in
succession. Press the Blue button to skip this section.
9.
The Enjoy your TV screen appears. and then press EnterE button.
16:9 Wide screen
Wide Fit
FAV.CH by pressing
MEDIA.P theMENU
Change
channels
the z
button
on the remote.
TOOLS
INFO
✎✎ If your TV is attached to a cable
or satellite box, you change the
channel using
EXITthe box’s remote.
EXIT
RETURN
MTS
S.MODE
SLEEP
MTS
CC
P.MODE
P.SIZE
CC
PRE-CH
Dynamic
Standard
✎✎This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, Volume buttons.
MEDIA.P
TOOLS
Press to select additional digital channels broadcast by
the same station. For example, to select channel 54-3,
press 54, press -, and then press 3.
PRE-CH
Return to the previous channel.
Change channels.
CHLIST
MEDIA.P
MENU
TOOLS
Colored buttons for use in the Channel List, Media Play
menu, etc.
Use these buttons in the Media Play and Anynet+ modes.
: controls recording on Samsung recorders with the
Anynet+ feature)
FAV.CH
INFO
Selects the on-screen menu items and changes the
values seen on the menu.
Return to the previous menu.
EXIT
RETURN
S.MODE
SLEEP
MTS
P.MODE
P.SIZE
CC
EXIT
RETURN
S.MODE
SLEEP
MTS
P.MODE
P.SIZE
CC
Exit the menu.
2.
Using your remote, press the Menu
button on your remote.
Then, select Setup → Time.
Month
Day
Year
--
--
----
Select Clock Mode, and then press
the EnterE button. Set Clock
Mode to Auto or Manual.
Hour
--
Minute
--
am/pm
--
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
Clock Set
L Move
✎✎ Select Auto if you have a digital
U Adjust
E Enter
R Return
channel in your area and are not
using a cable/sat box.
For a bright, detailed picture in a normally lit room.
For a comfortable, easy-on-the-eyes picture in a normally lit room.
When you set Clock Mode to Manual
Movie
For a studio quality cinema picture in a dimly lit or dark room.
4.
Select Clock Set, and then press the EnterE button. The Clock Set screen
appears.
5.
Using the number buttons on your remote, enter the month, day, year, hour,
and minute. Use the ◄ or ► button to move between entry fields.
6.
Press the Return button on your remote when done.
1.
With the TV on, press the Tools button on your remote.
The Tools menu appears.
2.
Using the ▲ or ▼ on your remote, select Picture mode.
3.
On the Picture Mode menu, use the ◄ or ► on your remote to select the
Picture Mode you want.
4.
Press the Exit button to exit the menu.
PRE-CH
To view the On Screen Menus, follow these steps:
1.
Displays Favorite Channel Lists on the screen.
Press to display information on the TV screen.
Turn on your TV.
Description
Viewing the On Screen Menus
Displays the main on-screen menu.
Displays the channel list on the screen.
Quickly selects frequently used functions.
INFO
1.
Natural
FAV.CH
Cut off the sound temporarily.
Adjusts the volume.
View the Media Play.
MENU
Setting the Clock
3.
To change the Picture Mode, follow these steps:
CHLIST
Press to switch between the sources (Blu-ray player,
cable box, DVD player, etc.) connected to your TV.
Power Indicator
Before you can use your TV’s On/Off Timer, you must set the clock. To set the
clock, follow these steps:
The Picture Modes are listed and described in the table below:
Mode
Remote control sensor
Screen Fit
Your TV has four preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
Remote Control Buttons and Functions:
Press number buttons for direct access to channels.
4:3 Standard screen
Changing the Picture Mode
To view the signal from a source connected to the HDMI, DVI, Component,
Composite, or D-sub jack, press the Source button on your remote. Each time
you press the Source button, you change to a different source.
Turns the TV on and off.
S.MODE theSLEEP
You can also change
channels by pressing
P.MODE theP.SIZE
z buttons on
the front panel of your TV
and adjust the volume by
pressing the y
buttons.
Zoom 2
on any side. It is only available when your TV inputs an HDMI (720p, 1080i,
1080p), Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
To watch a movie on your Blu-ray player or watch
your favorite TV show, you must select the correct
source. A source is a device, such as a Blu-ray/DVD
player, a cable/satellite box, antenna or a cable TV
input. Sources can be connected to your TV through
the HDMI, DVI, Component, Composite, or D-sub
connections, or through the Antenna or Cable In
connections.
If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital.
Zoom 1
✎✎ Screen Fit displays a full HD picture covering the entire screen with no cutoff
Selecting a Source
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press EnterE button on your remote. The Select Cable System screen
appears.
(
CHLIST
FAV.CH
MEDIA.P
Adjust the volume
by pressing
the
y button
TOOLS on the remote.
The following sizes are available:
PRE-CH
Channel
Volume
To change the screen size, press the P.Size button on your remote. The first time
you press it, your TV displays the current setting. There after, each time you press
the P.Size button, you change the size of the picture on the screen.
Select the daylight saving time setting: Off, On, or Auto, and then press
EnterE button.
Basic Functions
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
4.
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
✎✎ If you select Manual, the clock setting screen appears.
English
U Move E Enter
1.
Changing Channels and Adjusting the Volume
With the power on, press the Menu button
on your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel, Setup,
Input, Application, and Support.
CHLIST
MEDIA.P
MENU
TOOLS
Menu
2.
Press the ▲ or ▼ button on your remote
to select a menu option, and then press the
EnterE button.
3.
When done using the menu, press the Exit button on your remote to exit.
S.MODE: Selects the sound mode.
SLEEP: Setting the Sleep Timer.
You can enjoy photo, music, and movie files
stored on a USB device by connecting it to the TV
and using the Media Play feature. To connect a
USB device for Media Play, follow these steps:
1.
Turn on your TV.
2.
Connect a USB device
containing photo, music and/
or movie files to the USB (HDD)
jack on the side of the TV.
FAV.CH
INFO
EXIT
RETURN
Connecting a USB Device for Media Play
S.MODE
SLEEP
MTS
P.MODE
P.SIZE
CC
3.
When the Application selection
screen appears, press the
EnterE button on your
remote to select Media Play
(USB).
TV Side Panel
USB Drive
MediaPlay
Videos
SUM A Change Device
D View Devices E Enter R Return
MTS: Press to choose stereo, mono or Separate
Audio Program (SAP broadcast).
P.MODE: Selects picture mode.
P.SIZE: Choose the picture size.
CC: Controls the caption decoder.
BN68-02610A-01
English - 2
BN68-02610A-Eng.indd 2
2010-02-11 �� 11:30:29