www.epicfit.com
Model No. EPEX14912.2
Serial No.
Write the serial number in the
space above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts
are damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
VISIT OUR WEBSITE:
www.epicfit.com
Chat: Mon.––Fri. 6 a.m.––7 p.m. MT
CALL:
1-855-EPIC-FIT (1-855-374-2348)
Mon.––Fri. 6 a.m.––7 p.m. MT
EMAIL:
productsupport@epicfit.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
USER’’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
8. Keep children under age 12 and pets away
from the exercise bike at all times.
2. Use the exercise bike only as described in
this manual.
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
3. It is the responsibility of the owner to ensure
that all users of the exercise bike are adequately informed of all precautions.
10. The exercise bike should not be used by
persons weighing more than 300 lbs.
(136 kg).
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a commercial, rental, or institutional setting.
11. The heart rate monitor is not a medical
device. Various factors, including the user’’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
5. Keep the exercise bike indoors, away from
moisture and dust. Do not put the exercise
bike in a garage or covered patio, or near
water.
12. Always keep your back straight while using
the exercise bike; do not arch your back.
6. Place the exercise bike on a level surface
with at least 2 ft. (0.6 m) of clearance around
the exercise bike. To protect the floor or
carpet from damage, place a mat under the
exercise bike.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
3
BEFORE YOU BEGIN
Thank you for selecting the revolutionary EPIC™™ A17R
exercise bike. Cycling is an effective exercise for
increasing cardiovascular tness, building endurance,
and toning the body. The A17R exercise bike provides
an impressive selection of features designed to make
your workouts at home more effective and enjoyable.
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benet, read this manual carefully before
you use the exercise bike. If you have questions after
Length: 4 ft. 4 in. (132 cm)
Width: 2 ft. 2 in. (66 cm)
Console
Handlebar
Seat Handle
Seat
Console Knob
Backrest
Pedal/Strap
Wheel
Accessory Tray
Heart Rate Monitor
Leveling Foot
4
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M4 x 12mm
Screw (75)––10
M4 x 15mm
Screw (77)––1
M8 x 40mm
Screw (86)––10
M8 x 13mm
Screw (72)––6
M10 x 25mm
Screw (74)––5
M10 x 105mm
Screw (76)––2
5
M8 x 20mm
Screw (88)––1
M8 x 30mm
Screw (87)––1
M10 x 45mm
Screw (80)––2
ASSEMBLY
•• To watch an assembly
video, go to
http://productvideo.co/
assembly/dsg/epic or
use your mobile phone
or smartphone to read
the QR code with an
application such as
ShopSavvy.
•• Left parts are marked ““L”” or ““Left”” and right parts
are marked ““R”” or ““Right.””
•• To identify small parts, see page 5.
In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
•• Assembly requires two persons.
one rubber mallet
•• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
1. Set a sturdy piece of packing material under the
front of the Frame (1). Have a second person
hold the Frame to prevent it from tipping
while you complete this step.
1
2
Orient the Front Stabilizer (2) so that the wheels
(not shown) are facing away from the exercise
bike. Attach the Front Stabilizer to the Frame (1)
with two M10 x 105mm Screws (76).
76
Wheel
Remove the packing material.
1
2. Orient the Rear Stabilizer (3) as indicated by the
sticker.
2
Set the rear of the Frame (1) on the Rear
Stabilizer (3). Attach the Rear Stabilizer with two
M10 x 45mm Screws (80).
80
1
3
6
3. Attach the Seat Handlebar (5) to the Seat
Carriage (24) with four M8 x 40mm Screws (86);
start all four Screws, and then tighten them.
3
86
See the inset drawing. Plug the wire on
the Seat Handlebar (5) fully into the Pulse
Receptacle (64) on the left side of the exercise
bike.
5
86
24
64
5
4. Orient the Backrest Frame (17) as shown. Insert
the Backrest Frame into the Seat Carriage (24),
below the Seat Handlebar (5).
4
88
87
24
Attach the Backrest Frame (17) with an M8 x
30mm Screw (87) and an M8 x 20mm Screw
(88); start both Screws, and then tighten
them.
5
17
7
5. Identify the Right and Left Accessory Trays
(46, 85).
5
Attach the Right Accessory Tray (46) to the right
side of the Seat Handlebar (5) with two M4 x
12mm Screws (75).
46
85
Attach the Left Accessory Tray (85) to the left
side of the Seat Handlebar (5) in the same
way.
5
75
6. Attach the Seat (23) to the Seat Handlebar (5)
with four M8 x 40mm Screws (86); start all four
Screws, and then tighten them.
6
23
86
5
86
7. Attach the Backrest (90) to the Backrest Frame
(17) with two M8 x 40mm Screws (86); start
both Screws, and then tighten them.
7
90
17
86
8
8. Orient the Upright (4) and the Upright Sleeve
(37) as shown. Slide the Upright Sleeve onto the
Upright.
8
4
Have another person hold the Upright (4) and
the Upright Sleeve (37) near the front of the
Frame (1) as shown.
Wire Tie
Tie the lower end of the wire tie in the Upright (4)
to the Main Wire Harness (58) and to the Pulse
Wire (64) in the Frame (1).
37
58
Wire Tie
64
See the inset drawing. Pull the other end of the
wire tie until the Main Wire Harness (58) and the
Pulse Wire (64) are routed through the Upright
(4) and out of the indicated hole.
1
Hole
4
64
58
Wire Tie
9. Tip: Avoid pinching the wires.
9
Slide the Upright (4) onto the Frame (1). Attach
the Upright with five M10 x 25mm Screws (74);
start all five Screws, and then tighten them.
4
37
Avoid pinching
the wires
Then, slide the Upright Sleeve (37) downward
and press it onto the Right and Left Shields
(10, 11).
74
74
10, 11
1
9
10. Identify the Right Handlebar (6).
10
Attach the Right Handlebar (6) to the Console
Bracket (35) with three M8 x 13mm Screws (72);
start all three Screws, and then tighten them.
16
35
6
Attach the Left Handlebar (16) in the same
way.
72
11. While another person holds the Console (13)
near the Console Bracket (35), insert the console
wires into the hole in the center of the Console
Bracket.
11
13
75
Tip: Avoid pinching the wires. It may be
necessary to turn the Console Knob (27) and
adjust the angle of the Console Bracket (35).
Attach the Console (13) to the Console Bracket
(35) with four M4 x 12mm Screws (75).
35
Avoid pinching
the wires
10
27
12. Locate the longest wire on the Console (13).
Insert that wire downward into the top of the
Upright (4) and pull it out of the indicated hole.
12
13
Connect the other two wires on the Console (13)
to the Main Wire Harness (58) and to the Pulse
Wire (64).
4
Hole
64 58
13. Identify the Lower Pivot Cover (12).
13
Tip: Avoid pinching the wires. It may be
necessary to turn the Console Knob (not
shown) and adjust the angle of the Console
Bracket (35).
9
75
Attach the Lower Pivot Cover (12) to the Console
Bracket (35) with two M4 x 12mm Screws (75).
Make sure that the indicated wire is not
covered by the Lower Pivot Cover (see the
drawing in step 14).
Avoid
pinching
the wires
35
12
Next, press the Upper Pivot Cover (9) onto the
Lower Pivot Cover (12). Attach the Upper Pivot
Cover to the Console (13) with an M4 x 15mm
Screw (77).
14. Identify the Right Upright Cover (14), which has
the Receiver (59) attached.
13
77
Wire
14
Hold the Right Upright Cover (14) near the right
side of the Upright (4). Connect the wire on the
Receiver (59) to the indicated wire.
Avoid pinching
the wires
14
Tip: Avoid pinching the wires.
Next, press the Right Upright Cover (14) and
the Left Upright Cover (15) together around the
Upright (4).
59
4
11
Wire
15
15. Identify the Right Pedal (21).
15
Using the included flat wrench, firmly tighten
the Right Pedal (21) clockwise into the Right
Crank Arm (19).
Firmly tighten the Left Pedal (not shown)
counterclockwise into the Left Crank Arm (not
shown).
Adjust the strap on the Right Pedal (21) to the
desired position, and press the ends of the strap
onto the tabs on the Right Pedal. Adjust the
strap on the Left Pedal (not shown) in the
same way.
16. Plug the Power Adapter (67) into the receptacle
on the front of the exercise bike.
19
21
16
Note: To plug the Power Adapter (67) into an
outlet, see HOW TO PLUG IN THE POWER
ADAPTER on page 14.
67
17. Make sure that all parts are properly tightened before you use the exercise bike. Note: Extra parts may
be included. Place a mat beneath the exercise bike to protect the floor.
12
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
The heart rate
monitor consists of
a chest strap and a
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sensor under the buckle
on the chest strap.
The tab should be
flush with the front of
the sensor.
Tabs
•• Do not expose the heart rate monitor to direct sunlight for extended periods of time; do not expose it to
temperatures above 122° F (50° C) or below 14° F
(-10° C).
Chest
Strap
•• Do not excessively bend or stretch the sensor when
using or storing the heart rate monitor.
Sensor
•• To clean the sensor, use a damp cloth and a small
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
TROUBLESHOOTING
Tab
If the heart rate monitor does not function properly, try
the steps below.
Sensor Buckle
The heart rate monitor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the
location shown.
Make sure that
the logo is rightside-up. Then, attach the other end of the chest strap
to the sensor. Adjust the length of the chest strap, if
necessary.
•• Make sure that you are wearing the heart rate monitor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
•• If heart rate readings are not displayed until you
begin perspiring, rewet the electrode areas.
•• For the console to display heart rate readings, you
must be within arm’’s length of the console.
•• If there is a battery cover on the back of the sensor,
replace the battery with a new battery of the same
type.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
•• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
CARE AND MAINTENANCE
•• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
•• Thoroughly dry the sensor with a soft towel after
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
•• Store the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
13
HOW TO USE THE EXERCISE BIKE
HOW TO PLUG IN THE POWER ADAPTER
HOW TO ADJUST THE ANGLE OF THE
CONSOLE AND THE HANDLEBARS
IMPORTANT: If the exercise bike has been exposed
to cold temperatures, allow it to warm to room
temperature before plugging in the power adapter.
If you do not do this, you may damage the console
displays or other electronic components.
Plug the power adapter
into the receptacle
on the frame of the
exercise bike. Then,
plug the power adapter
into an appropriate
outlet that is properly
installed in accordance
with all local codes and
ordinances.
To adjust the angle of
the console and the
handlebars, simply
turn the handlebar
knob clockwise or
counterclockwise.
Power Adapter
Knob
HOW TO ADJUST THE PEDAL STRAPS
To adjust the pedal
straps, rst pull the
ends of the straps off
the tabs on the pedals.
Adjust the straps to the
desired position, and
then press the ends
of the straps onto the
tabs.
HOW TO ADJUST THE SEAT
To adjust the seat, push downward on the seat handle,
slide the seat forward or backward to the desired position, and then pull upward on the seat handle to lock
the seat in place.
Strap
Tab
HOW TO LEVEL THE EXERCISE BIKE
Handle
If the exercise bike
rocks slightly on your
oor during use, turn
one or both of the
leveling feet beneath
the rear stabilizer until
the rocking motion is
eliminated.
Leveling
Feet
14
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The console also offers user-defined workouts that
allow you to create your own workouts and store them
in memory for future use.
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the resistance of the pedals with the touch
of a button.
The console features revolutionary iFit Live technology that enables the console to communicate with
your wireless network. With iFit Live technology, you
can download personalized workouts, create your
own workouts, track your workout results, and access
many other features. See www.iFit.com for complete
information.
While you exercise, the console will display continuous
exercise feedback. You can also measure your heart
rate using the handgrip heart rate monitor or the chest
heart rate monitor.
You can also listen to your favorite workout music or
audio books with the console sound system while you
exercise.
In addition, the console features a selection of onboard
workouts. Each onboard workout automatically
changes the resistance of the pedals and prompts you
to vary your pedaling speed as it guides you through
an effective workout. You can also set a time, distance,
or calorie goal.
To set up the console, see page 16.
15
HOW TO SET UP THE CONSOLE
3. Check for firmware updates.
Before using the exercise bike for the first time, set up
the console.
See HOW TO CHANGE CONSOLE SETTINGS on
page 23 and check for firmware updates.
1. Create an iFit Live account.
The console is now ready for you to begin working out.
The following pages explain the various workouts and
other features that the console offers.
To create an iFit Live account, or for more
information about the account, go to
www.iFit.com and click Register.
To use the manual mode, see page 17. To use
an onboard workout, see page 19. To use a
set-a-goal workout, see page 20. To create a
user-defined workout, see page 20. To use a
user-defined workout, see page 21. To use an iFit
Live workout, see page 22. To change console
settings, see page 23. To use the sound system,
see page 25.
Click Buy Now to register for an iFit account. If you
have an activation code, select the code activation
option. Then, follow the prompts to sign up for your
iFit membership.
2. Connect to your wireless network.
Note: In order to download iFit Live workouts and
use other features of the console, you must be
connected to a wireless network. See HOW TO
CHANGE CONSOLE SETTINGS on page 23 to
connect the console to your wireless network.
Note: If there is a sheet of plastic on the display,
remove the plastic.
Note: The console can display distance in either
miles or kilometers. To find which unit of measurement is selected, see HOW TO CHANGE CONSOLE
SETTINGS on page 23.
16
HOW TO USE THE MANUAL MODE
Calories per Hour (Calories/Hr)——This display
mode will show the approximate number of calories
you are burning per hour.
1. Begin pedaling or press any button on the
console to turn on the console.
Distance——This display mode will show the distance that you have pedaled in miles or kilometers.
When you turn on the console, the display will turn
on. The console will then be ready for use.
Laps——This display mode will show a track that
represents 1/4 mile (400 m). As you exercise, indicators will appear in succession around the track
to show your progress. The Laps display mode will
also show the number of laps you complete.
2. Select the manual mode.
The manual mode will be selected automatically
each time you turn on the console.
Note: If the console is connected to iFit Live
through your wireless network, the display will
cycle between the manual mode and the iFit Live
welcome message. Press the Home button repeatedly to select the manual mode.
Pulse——This display mode will show your heart rate
when you use the handgrip heart rate monitor or
the chest heart rate monitor (see step 5).
Resistance——This display mode will show the
resistance level of the pedals for a few seconds
each time the resistance level changes.
You can also press any of the workouts buttons
repeatedly to select the manual mode.
RPM——This display mode will show your pedaling
speed in revolutions per minute (rpm).
3. Change the resistance of the pedals as desired.
As you pedal, you can change the resistance of the
pedals. To change the resistance, press the Quick
Resistance increase and decrease buttons or press
one of the numbered Quick Resistance buttons.
Speed——This display mode will show your pedaling
speed in miles or kilometers per hour.
Time——This display mode will show the elapsed
time.
Note: After you press a button, it will take a
moment for the pedals to reach the selected resistance level.
The matrix offers several display modes. Press the
increase and decrease buttons near the Enter button until the desired display mode is shown.
4. Follow your progress.
Speed——This display mode will show a history of
the speed settings of your workout. A new segment
will appear at the end of each minute.
The display can show the following workout
information:
Calories——This display mode will show the approximate number of calories you have burned.
Calorie——This display mode will show the approximate amount of calories you have burned. The
height of each segment represents the amount of
calories burned during that segment. A new segment will appear at the end of each minute.
17
To pause the manual mode or a workout, stop pedaling. The time will pause in the display. To resume
the manual mode or the workout, simply resume
pedaling.
When your pulse is detected, your heart rate
will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15
seconds.
Press the Home button to exit the manual mode
or a workout. If necessary, press the Home button
again.
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
When the console is connected to a
wireless network, the wireless symbol
in the display will show the strength
of your wireless signal. Four arcs
indicate full signal strength. If the wireless symbol
is flashing, the console is not connected to a wireless network.
6. Turn on the fan if desired.
The fan has high and low speed
settings. Press the fan increase and
decrease buttons repeatedly to select
a fan speed or to turn off the fan.
If desired, adjust the volume level by
pressing the volume increase and
decrease buttons on the console.
Note: If the pedals do not move for a
while, the fan will turn off automatically.
5. Measure your heart rate if desired.
7. When you are finished exercising, the console
will turn off automatically.
To use the chest heart rate monitor, see page
13. To use the handgrip heart rate monitor, follow the instructions below. IMPORTANT: If you
use both heart rate monitors at the same time,
the console will not display your heart rate
accurately.
If the pedals do not move for several seconds, a
tone will sound, the console will pause, and the
time will flash in the display. To resume your workout, simply resume pedaling.
If the pedals do not move for several minutes and
the buttons are not pressed, the resistance of the
pedals will increase, the console will turn off, and
the display will be reset.
If there are sheets
of plastic on the
Contacts
metal contacts
on the handgrip
heart rate monitor, remove the
plastic. To measure your heart
rate, hold the
handgrip heart
rate monitor with
your palms resting
against the contacts. Avoid moving your hands
or gripping the contacts tightly.
18
HOW TO USE AN ONBOARD WORKOUT
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Quick Resistance buttons.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Select an onboard workout.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
To select an onboard workout, press the Calorie
button or the Performance button repeatedly until
the name of the desired workout appears in the
display.
When you select an onboard workout, the display
will show the name, duration, and distance of the
workout. The display will also show the approximate number of calories you will burn during the
workout and a profile of the resistance settings of
the workout.
The workout will continue in this way until the last
segment ends. To pause the workout, stop pedaling. The time will pause in the display. To resume
the workout, simply resume pedaling.
3. Begin pedaling to start the workout.
4. Follow your progress.
Each workout is divided into segments. One
resistance level and one target rpm (speed) are
programmed for each segment. Note: The same
resistance level and/or target rpm may be programmed for consecutive segments.
See step 4 on page 17.
The matrix will also show a profile of the resistance
settings of the workout or a map.
5. Measure your heart rate if desired.
During the workout, the profile will show your progress. The flashing segment of the profile represents
the current segment of the workout. The height of
the profile indicates the approximate resistance
level for the current segment.
See step 5 on page 18.
6. Turn on the fan if desired.
See step 6 on page 18.
At the end of each segment of the workout, the
resistance of the pedals will change.
7. When you are finished exercising, the console
will turn off automatically.
As you exercise, keep your pedaling speed
near the target rpm for the current segment.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
See step 7 on page 18.
19
HOW TO USE A SET-A-GOAL WORKOUT
HOW TO CREATE A USER-DEFINED WORKOUT
1. Begin pedaling or press any button on the
console to turn on the console.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
When you turn on the console, the display will turn
on. The console will then be ready for use.
2. Set a calories, distance, or time goal.
2. Select a user-defined workout.
Press the Set A Goal button repeatedly until the
name of the desired goal appears in the display.
To select a user-defined workout, press the User
Defined button repeatedly until the name of the
desired workout appears in the display. A profile will
also appear in the display.
Then, press the increase and decrease buttons
near the Enter button to set the desired goal.
3. Begin pedaling and program the desired
settings.
3. Begin pedaling to start the workout.
As you exercise, a target rpm (speed) may
appear in the display to help you reach your goal.
Keep your pedaling speed near the target rpm.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
Each workout is divided into segments. You can
program one resistance level and one target rpm
(speed) for each segment.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
To program a target rpm (speed), simply pedal at
the desired speed.
To program a resistance level for the first segment,
simply adjust the resistance of the pedals by pressing the Quick Resistance buttons.
At the end of the first segment, the workout will
store the current resistance level and pedaling
speed in memory.
Program a resistance level and a target rpm for the
second segment as described above.
The workout will continue in this way until the calories, distance, or time goal is reached. To pause
the workout, stop pedaling. The time will pause in
the display. To resume the workout, simply resume
pedaling.
Continue exercising for up to one hundred minutes.
Press the Home button when you are finished with
your workout. Then, press the Enter button. The
workout you created will then be stored in memory.
4. Follow your progress.
4. When you are finished exercising, the console
will turn off automatically.
See step 4 on page 17.
See step 7 on page 18.
5. Measure your heart rate if desired.
See step 5 on page 18.
6. Turn on the fan if desired.
See step 6 on page 18.
7. When you are finished exercising, the console
will turn off automatically.
See step 7 on page 18.
20
HOW TO USE A USER-DEFINED WORKOUT
The workout will continue in this way until the last
segment ends. To pause the workout, stop pedaling. The time will pause in the display. To resume
the workout, simply resume pedaling.
1. Begin pedaling or press any button on the
console to turn on the console.
When you turn on the console, the display will turn
on. The console will then be ready for use.
4. Change the workout if desired.
If desired, you can change the workout while you
are using it.
2. Select a user-defined workout.
To select a user-defined workout, press the User
Defined button repeatedly until the name of the
desired workout appears in the display. The display
will also show a profile of the resistance settings of
the workout.
To change the resistance level for the current
segment, simply press the Quick Resistance buttons. At the end of the current segment, the new
resistance level will be stored in memory.
To change the target rpm for the current segment, simply change your pedaling speed. At the
end of the current segment, your pedaling speed
will be stored in memory.
Note: To create a user-defined workout, see HOW
TO CREATE A USER-DEFINED WORKOUT on
page 20.
3. Start the workout.
If desired, you can shorten the workout. To
shorten the workout, press any workout button on
the console, and then press the Enter button to trim
the workout.
Each workout is divided into segments. One
resistance level and one target rpm (speed) are
programmed for each segment. Note: The same
resistance level and/or target rpm may be programmed for consecutive segments.
If desired, you can extend the workout when
you reach the end of the workout. To extend the
workout, follow the instructions in the matrix.
During the workout, the profile will show your progress. The flashing segment of the profile represents
the current segment of the workout. The height of
the flashing segment indicates the resistance level
for the current segment.
Continue exercising for up to one hundred minutes.
Press the Home button when you are finished with
your workout. Then, press the Enter button. The
workout will then be stored in memory.
At the end of each segment of the workout, the
resistance of the pedals will change.
5. Follow your progress.
See step 4 on page 17.
As you exercise, keep your pedaling speed
near the target rpm for the current segment.
IMPORTANT: The target rpm is intended only to
provide motivation. Your actual pedaling speed
may be slower than the target rpm. Make sure
to pedal at a speed that is comfortable for you.
6. Measure your heart rate if desired.
See step 5 on page 18.
7. Turn on the fan if desired.
If the resistance level for the current segment is too
high or too low, you can manually override the setting by pressing the Quick Resistance buttons.
See step 6 on page 18.
8. When you are finished exercising, the console
will turn off automatically.
IMPORTANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
See step 7 on page 18.
21
HOW TO USE AN IFIT LIVE WORKOUT
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories that
you burn will depend on various factors such
as your weight. In addition, if you manually
change the resistance of the pedals during the
workout, the number of calories you burn will
be affected.
Note: To use an iFit Live workout, you must have
access to a wireless network (see page 23). An iFit
Live account is also required (see step 1 on
page 16.
1. Begin pedaling or press any button on the
console to turn on the console.
5. Begin pedaling to start the workout.
When you turn on the console, the display will turn
on. The console will then be ready for use.
See step 3 on page 19.
2. Select the iFit Live mode.
During some workouts, the voice of a personal
trainer will guide you through your workout.
Press the Home button repeatedly to select the
iFit Live mode. The iFit Live welcome message will
appear in the display.
To stop the workout at any time, stop pedaling. The
time will flash in the display. To resume the workout, simply resume pedaling.
3. Select a user.
6. Follow your progress.
If more than one user is registered with your
iFit.com membership, you can switch users in
the iFit Live main screen. Press the increase and
decrease buttons near the Enter button to select a
user.
See step 4 on page 17.
During a competition workout, the display can show
your progress in the race. As you race, the top line
in the matrix will show how much of the race you
have completed. The other lines will show your top
four competitors. The end of the matrix represents
the end of the race.
4. Select an iFit Live workout.
To download an iFit Live workout in your schedule,
press the Map, Train, or Lose Wt. button to download the next workout of that type in your schedule.
7. Measure your heart rate if desired.
To compete in a race that you have previously
scheduled, press the Compete button.
See step 5 on page 18.
8. Turn on the fan if desired.
To re-run a recent iFit Live workout from your
schedule, press the Track button, press the
increase and decrease buttons to select the
desired workout, and then press the Enter button to
start the workout.
See step 6 on page 18.
9. When you are finished exercising, the console
will turn off automatically.
To use a set-a-goal workout, press the Set A Goal
button (see page 20).
See step 7 on page 18.
For more information about iFit Live workouts, go
to www.iFit.com.
Before some workouts will download, you must add
them to your schedule on iFit.com.
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter inside
the console must be at least 8 in. (20 cm) from all
persons and must not be near or connected to any
other antenna or transmitter.
For more information about the iFit Live workouts, please see www.iFit.com.
When you select an iFit Live workout, the display
will show the name, duration, and distance of the
workout. The display will also show the approximate number of calories you will burn during the
workout and a profile of the resistance settings of
the workout.
22
HOW TO CHANGE CONSOLE SETTINGS
Contrast——The contrast level of the display will
appear in the matrix. Press the Quick Resistance
increase and decrease buttons to adjust the contrast level.
The console features a settings mode that allows you
to view usage information, to personalize console settings, and to set up and manage a wireless network
connection.
Firmware Update——For the best results,
regularly check for firmware updates.
1. Select the settings mode.
Note: The matrix will display NOT CONNECTED if
the console is not connected to a wireless network.
To select the settings mode, press and hold down
the Calorie button until the settings mode appears
in the display.
Press the Enter button to check for firmware
updates using your wireless network. If an update
is available, the update will begin automatically.
The time display will show the total number of
hours that the exercise bike has been used.
IMPORTANT: To avoid damaging the exercise
bike, do not unplug the power adapter while
the firmware is being updated. The update may
take several minutes.
The distance display will show the total number of
miles (or kilometers) that have been pedaled on the
exercise bike.
2. Navigate the settings mode menu.
Note: Occasionally, a firmware update may cause
your console to function slightly differently. These
updates are always designed to improve your exercise experience.
The matrix will display a menu of the settings mode
options.
Press the increase and decrease buttons near the
Enter button to highlight the desired option.
Default Settings——To restore the console to its
factory default settings, press the Enter button.
Note: The console will erase any information that
you have saved in its memory.
The lower part of the matrix will display instructions
for the highlighted option. Make sure to follow the
instructions displayed in the lower part of the
matrix.
IP Address——An IP address will appear in the
matrix. Note: This IP address is for reference.
3. Change settings as desired.
The WiFi––Normal option will allow you to set up
a wireless network connection using the console.
See step 4 for instructions.
Demo——The console features a display demo
mode, designed to be used if the exercise bike
is displayed in a store. While the demo mode is
turned on, the display will not enter sleep mode
when the exercise bike is not in use. If the demo
mode is turned on, the word ON will appear in the
matrix. To turn on or turn off the demo mode, press
the Enter button.
The WiFi––WPS option will allow you to set up
a wireless network connection using your WPS
router. See step 5 for instructions.
The WiFi––Advanced option will allow you to set up
a wireless network connection using your computer, smart phone, tablet, or other Wi-Fi device.
See step 6 for instructions.
Units——The selected unit of measurement will
appear in the matrix. To change the unit of measurement, press the Enter button. To view distance
in miles, select ENGLISH. To view distance in
kilometers, select METRIC.
23
iFit User Setup——To set up a different iFit Live
account, but maintain the existing wireless connection, follow the instructions in the matrix.
Note: This option will be used rarely.
Press the up, down, left, and right buttons to highlight the desired letter or number. Then, press the
Enter button to select the letter, number, or symbol.
When you have finished entering the password,
press the Done button.
Clear WiFi——To erase the console’’s wireless
network settings and have it forget the currently
selected wireless network, follow the instructions in
the matrix.
Next, a numerical code and a web address will
appear in the matrix.
Open a web browser on your computer, smart
phone, tablet, or other internet-compatible device
and go to the web address.
4. Use WiFi––Normal to set up a wireless
connection.
This option will allow you to set up a wireless network connection using the console.
Log in to your iFit Live account on the web page.
Then, enter the numerical code into the indicated
field on the web page. Follow any other instructions
on the web page.
Note: You will need to know your network name
(SSID). If your network has a password, you will
also need to know the password.
Then, unplug the power adapter, wait for several
seconds, and then plug in the power adapter again.
Note: It may take a few minutes for the console to
be ready for use.
To set up a wireless network connection using the
console, first press the Enter button.
IMPORTANT: Set
the included WiFi
setup card on
the console. The
buttons on the
WiFi setup card
are referenced
in the following
instructions.
When the console is connected to a wireless
network, the wireless symbol in the display will
stop flashing and become solid. The wireless symbol will show the strength of your wireless signal;
four arcs indicate full signal strength.
Card
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
5. Use WiFi––WPS to set up a wireless connection.
A list of networks will appear in the matrix. Press
the up and down buttons to highlight the desired
network. Then, press the Enter button. Note: Do
not select IFIT_SETUP.
This option will allow you to set up a wireless network connection using your WPS router.
To set up a wireless network connection using your
WPS router, first press the Enter button and follow
the instructions in the matrix.
Note: The time display will show the number of
the currently-selected access point. The distance
display will show the total number of access points
detected.
If the network has a password, enter the password.
A numerical code and a web address will appear in
the matrix. Open a web browser on your computer,
smart phone, tablet, or other internet-compatible
device and go to the web address.
A keyboard will appear in the matrix. As necessary,
press the buttons on the WiFi setup card to select
the caps option, the number option, or the symbol
option.
Log in to your iFit Live account on the web page.
Then, enter the numerical code into the indicated
field on the web page. Follow any other instructions
on the web page.
24
Then, unplug the power adapter, wait for several
seconds, and then plug in the power adapter again.
Note: It may take a few minutes for the console to
be ready for use.
Your browser will load a web page. If the web page
does not appear, double-check the IP address and
the previous instructions of this step. Follow the
instructions on the web page to connect the exercise bike to your wireless network.
When the console is connected to a wireless
network, the wireless symbol in the display will
stop flashing and become solid. The wireless symbol will show the strength of your wireless signal;
four arcs indicate full signal strength.
Note: A warning may appear stating that the server
cannot be identified. If this happens, make sure
that you have entered the IP address correctly.
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
If you cannot complete any part of this
process, or if you have any questions, go to
http://support.ifit.com for assistance.
7. Exit the information mode.
6. Use WiFi––Advanced to set up a wireless
connection.
To exit the information mode, press the Calorie
button.
This option will allow you to set up a wireless
network connection using your computer, smart
phone, tablet, or other Wi-Fi device.
HOW TO USE THE SOUND SYSTEM
On your computer, smart phone, tablet, or other
Wi-Fi device, open the list of available networks to
which your device can connect. One of the options
will be IFIT_SETUP; select this network. If this network does not appear, make sure that your Wi-Fi
device is within range of the console, and then
close and re-open your list of networks. Also, see
CLEAR WIFI on page 24 and clear any previous
wireless network settings on the console.
To play music or audio books through the console
sound system, you must connect your MP3 player, CD
player, or other personal audio player to the console.
Note: The network IFIT_SETUP will not appear
if the console has already been configured to
connect to a wireless network. Also, AndroidTM
devices may not be able to detect IFIT_SETUP.
Next, press the play button on your MP3
player, CD player, or other personal audio
player. Then, adjust the volume level on
your personal audio player or press the
volume increase and decrease buttons
on the console.
Plug one end of your audio wire into the audio jack
on the console. Then, plug the other end into a jack
on your MP3 player, CD player, or other personal
audio player. Make sure that your audio wire is fully
plugged in.
The console will display an IP address, such as
192.168.0.1:8080. Open a web browser on your
computer, smart phone, tablet, or other Wi-Fi
device. Next, type in the IP address on the console into the URL bar in your browser. Example:
http://192.168.0.1:8080.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat
surface instead of on the console.
25
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15C and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, try to correct the interference by one or more of the following measures:
••
••
••
••
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’’s authority to operate this equipment.
IMPORTANT: To satisfy exposure compliance requirements, the antenna and transmitter in the console
must be at least 8 in. (20 cm) from all persons and must not be near or connected to any other antenna or
transmitter.
Note: The console contains FCC ID: X2NBL-LW02-2
26
MAINTENANCE AND TROUBLESHOOTING
IMPORTANT: Servicing other than the procedures
described below should be performed only by an
authorized service representative.
8
Inspect and tighten all parts of the exercise bike regularly. Replace any worn parts immediately.
To clean the exercise bike, rst press the power
switch to the off position and unplug the power
adapter. Wipe exterior parts of the exercise bike
with a damp cloth and a few drops of mild dish soap.
Then, wipe the exercise bike with a cloth dampened
with clean water, and dry the exercise bike with a soft
towel. IMPORTANT: Do not spray liquid directly
onto the console or onto other parts of the exercise bike. To avoid damage to the console, keep
the console out of direct sunlight.
38
55
78
57
CONSOLE TROUBLESHOOTING
If lines appear in the console display, see HOW TO
CHANGE CONSOLE SETTINGS on page 23 and
adjust the contrast level of the display.
Locate the Reed Switch (57). Turn the Pulley (38) until
a Magnet (55) is aligned with the Reed Switch. Next,
loosen, but do not remove, the indicated M4.2 x 18mm
Screw (78). Slide the Reed Switch slightly closer to or
away from the Magnet, and then retighten the Screw.
If the console does not display your heart rate when
you use the handgrip heart rate monitor, see step 5 on
page 18.
Plug in the power adapter, and turn the Pulley (38) for
a moment.
If the console does not display your heart rate
when you use the chest heart rate monitor, see
TROUBLESHOOTING on page 13.
Repeat these actions until the console displays correct
feedback. When the reed switch is correctly adjusted,
reattach the front shield cover.
HOW TO ADJUST THE REED SWITCH
STORAGE
If the console does not display correct feedback, the
reed switch should be adjusted.
If the exercise bike will not be used for an extended
period of time, unplug the power adapter and lay it
over the exercise bike where it will not be pinched or
crushed, and cover the exercise bike to keep it free
of dust. Store the exercise bike indoors. Do not store
objects on the exercise bike.
To adjust the reed switch, first unplug the power
adapter (not shown). Using a flat screwdriver, gently
release the tabs on the Front Shield Cover (8) and lift
the Front Shield Cover off the exercise bike.
27
EXERCISE GUIDELINES
Burning Fat——To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise——If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up——Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise——Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down——Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your ““training zone.”” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
28
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch; never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach down
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times. Stretches: Hamstrings, back of knees and back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
29
5
NOTES
30
NOTES
31
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
2
1
2
2
1
1
1
2
1
1
1
2
2
1
4
1
1
1
1
1
1
1
Model No. EPEX14912.2 R0912A
Description
Key No. Qty.
Frame
Front Stabilizer
Rear Stabilizer
Upright
Seat Handlebar
Right Handlebar
Rear Shield Cover
Front Shield Cover
Upper Pivot Cover
Right Shield
Left Shield
Lower Pivot Cover
Console
Right Upright Cover
Left Upright Cover
Left Handlebar
Backrest Frame
Crank Cover Cap
Right Crank Arm
Left Crank Arm
Right Pedal/Strap
Left Pedal/Strap
Seat
Seat Carriage
Backrest Frame Cap
Knob Cap
Console Knob
Seat Rail
Leveling Foot
Seat Rail Cap
Crank Arm Cover
Rear Stabilizer Cap
Right Stabilizer Cap/Wheel
Left Stabilizer Cap/Wheel
Console Bracket
M4 x 25mm Screw
Upright Sleeve
Pulley
Crank
Crank Bearing
Snap Ring
Eddy Mechanism
Crank Arm Bracket
Frame Cap
Idler
Right Accessory Tray
Resistance Motor
Knob Shaft
Upper Frame Cover
Large Shaft Block
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
32
1
1
1
1
2
1
1
1
1
2
1
2
2
1
1
2
1
2
1
4
4
6
2
5
12
2
3
13
4
2
1
1
1
1
1
10
1
5
4
1
1
3
2
4
2
1
1
2
1
2
Description
Small Shaft Block
Lower Frame Cover
Heart Rate Monitor/Strap
Drive Belt
Magnet
Clamp
Reed Switch/Wire
Main Wire Harness
Receiver
Handlebar Bushing
Handlebar Axle
M8 Flange Screw
Upright Bushing
Pulse Wire/Receptacle
Power Wire/Receptacle
Handlebar Cap
Power Adapter
M8 Washer
Ground Screw
M8 x 15mm Shoulder Screw
M8 x 18mm Bolt
M8 x 13mm Screw
M10 Jam Nut
M10 x 25mm Screw
M4 x 12mm Screw
M10 x 105mm Screw
M4 x 15mm Screw
M4.2 x 18mm Screw
M4.5 x 12mm Screw
M10 x 45mm Screw
Belt Adjustment Screw
M6 x 20mm Screw
Idler Screw
M6 Washer
Left Accessory Tray
M8 x 40mm Screw
M8 x 30mm Screw
M8 x 20mm Screw
M8 Locknut
Backrest
Backrest Bracket
Frame Foot/Bumper
M10 x 48mm Screw
M10 x 20mm Screw
M8 x 15mm Screw
Seat Handle
Handle Grip
M6 x 15mm Screw
Brake Block
Block Spacer
Key No. Qty.
101
102
103
104
105
106
107
10
1
4
5
1
2
1
Description
Key No. Qty.
M6 x 25mm Bolt
M4 x 15mm Pan Head Screw
Roller
Roller Axle
M6 x 12mm Screw
Seat Handlebar Cap
Handle Bracket
108
109
110
111
112
*
*
8
2
10
1
3
––
––
Description
M4 x 15mm Flat Head Screw
M6 x 10mm Screw
M6 x 16mm Washer
Brake Plate
M8 Nut
Assembly Tool
User’’s Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
33
EXPLODED DRAWING A
Model No. EPEX14912.2 R0912A
23
90
9
15
77
13
75
88
85
75
25
91
86
95
68
88
86
60
25
5
66
75 86
63
59
61
72
17
106
35
70
16
4
63
50
112
14
60
46
70
70
72
75
75
86
104
97
87
24
110
103
66
105
102
101
30 41
2
109
77
45
100
92
64
89
84
89
82
78
83
42
92
78
65
55
81
1
80
39 55
77
78
93
33
41
94
78
32
40
69
92
94
76
40
56
98
72
57
28
111
99
100
12
34
26
78
107
74 95
6
79
47
96
74
27
88
101
110
104
51
48
75
71
58
38
67
73
54
29
68
73
3
32
29
34
53
EXPLODED DRAWING B
Model No. EPEX14912.2 R0912A
11
22
31
18
37
20
43
62
8
78
36
36
78
108
10
78
7
44
108
78
49
78
43
19
31
62
18
78
52
21
35
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
•• the model number and serial number of the product (see the front cover of this manual)
•• the name of the product (see the front cover of this manual)
•• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.epicfit.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and the eddy mechanism are warranted for
the lifetime of the original purchaser (customer). Parts and labor are warranted for one (1) year from the
date of purchase.
This warranty extends only to the original purchaser (customer). ICON’’s obligation under this warranty is
limited to repairing or replacing, at ICON’’s option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’’s responsibility. If
replacement parts are shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to freight damage to the product. This warranty will automatically be voided
if the product is used as a store display model, if the product is purchased or transported outside the USA,
if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used,
or if the product is used for commercial or rental purposes. No other warranty beyond that specically set
forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or prots, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or tness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer.
This warranty provides specic legal rights; the customer may have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 329682 R0912A
Printed in China © 2012 ICON IP, Inc.