R
Commercial
Service Training Manual
RCS / MCS Models
RCS / MCS - 60 Hz
August 2012
16400020
® / ™ © 2012 Amana. All rights reserved. Brand used under license.
1
Table of Contents
Important Safety Information........................................................................................3-6
Installation.......................................................................................................................7
!"#$%#&'$()*++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++,
Quick Start Reference Guide (Electronic Mechanical Dial)............................................9
Quick Start Reference Guide (Electronic Control)....................................................10-11
Components Location..............................................................................................12-16
Performance Testing Procedures..................................................................................17
-(.!()")'/0"*'$)1/23(#"453"*/++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++6,768
Troubleshooting.......................................................................................................20-21
Schematic / Wiring Diagrams.......................................................................................22
Important Information
Important Notices for Servicers and Consumers
ACP will not be responsible for personal injury or property damage from improper service procedures. Pride and
workmanship go into every product to provide our customers with quality products. It is possible, however, that during
its lifetime a product may require service. Products should be serviced only by a qualified service technician who is
familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts, testing
instruments and the appropriate service information. IT IS THE TECHNICIANS RESPONSIBLITY TO REVIEW ALL
APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.
!
WARNING
To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid
electrical shock.
To locate an authorized servicer please contact:
ComServ Support Center
Web Site
WWW.ACPSOLUTIONS.COM
.......................
Telephone Number
1-866-426-2621 or 319-368-8195
E-Mail: commercialservice@acpsolutions.com
Recognize Safety Symbols, Words, and Labels
!
DANGER
DANGER— Immediate hazards which WILL result in severe personal injury or death.
!
WARNING
WARNING— Hazards or unsafe practices which COULD result in severe personal injury or death.
!
CAUTION
CAUTION— Hazards or unsafe practices which COULD result in minor personal injury, product or property
damage.
3
Important Safety Information
!
WARNING
Read the following information to avoid possible exposure to microwave radiation:
The basic design of the Microwave Oven makes it an inherently safe device to both use and service.
However, there are some precautions which should be followed when servicing the microwave to maintain this
safety. These are as follows:
1. Always operate the unit from an adequately
grounded outlet. Do not operate on a two-wire
extension cord.
8. Do not for any reason defeat the interlock
switches there is not valid reason for this action
at any time; nor will it be condoned by ACP.
2. Before servicing the unit (if unit is operable) perform
the microwave leakage test.
9. IMPORTANT: Before returning a unit to a
customer, be sure to check for proper switch
interlock action.
3. The oven should never be operated if the door does
not fit properly against the seal, the hinges or hinge
bearings are damaged or broken; the choke is
damaged, (pieces missing, etc.); or any other
visible damage can be noted. Check the choke
area to ensure that this area is clean and free of all
foreign matter.
10. The Microwave Oven should never be
operated with any components removed and/or
bypassed or when any of the safety interlocks are
found to be defective, or when any of the seal
surfaces are defective, missing, or damaged.
11. All microwave ovens meet all requirements
of the radiation control for Health and Safety Act of
1968. Due to measurement uncertainties, the
maximum leakage for the field will be 4mw/cm2.
4. If the oven operates with the door open and
produces microwave energy, take the following
steps:
A. Tell the user not to operate the oven.
B. Contact ACP ComServ immediately.
12. To ensure that the unit does not emit excessive
microwave leakage and to meet the Department
of Health and Human Services guidelines, check
the oven for microwave leakage using a microwave
oven leakage meter that complies with US
Government CDRH / FDA / DHHS requirements
and or any other local government requirements.
The maximum leakage level allowed by ACP
2
is 4mw/cm .
5. Always have the oven disconnected when the outer
case is removed except when making the "live"
tests called for in the Service Manual. Do not
reach into the equipment area while the unit is
energized. Make all connections for the test and
check them for tightness before plugging the cord
into the outlet.
6. Always ground the capacitors on the magnetron
filter box with an insulated-handle screwdriver
before working in the high voltage area of the
equipment compartment. Some types of failures
will leave a charge in these capacitors and the
discharge could cause a reflex action which could
make you injure yourself.
13. If servicer encounters an emission reading over
4mw/cm 2, the servicer is to cease repair and
contact the ACP ComServ Department
immediately for further direction. ACP
will contact the proper Government
Agency upon verification of the test results.
7. Always remember that in the area of the
transformer there is HIGH VOLTAGE. When the
unit is operating keep this area clear and free of
anything which could possibly cause an arc or
ground, etc.
4
IMPORTANT SAFETY INSTRUCTIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
WARNING
When using electrical equipment, basic safety precautions should be followed to reduce the risk of burns,
"<"#'3$#&</*:(#ML/%3"L/(3/$)>53?/'(/!"3*()*/$)#<54$)1/':"/K(<<(P$)1+/
1. READ all instructions before using equipment.
9. DO NOT heat baby bottles in oven.
B+/ CDE9/EF9/GHIIHJ/':"/*!"#$%#/
“PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY” on this page.
10. Baby food jars shall be open when heated and
contents stirred or shaken before consumption, in
order to avoid burns.
3. This equipment MUST BE GROUNDED. Connect
only to properly GROUNDED outlet. See “
GROUNDING / EARTHING INSTRUCTIONS” on
page 5.
4. Install or locate this equipment ONLY in
accordance with the installation instructions in
this manual.
5. Some products such as whole eggs and sealed
containers—for example, closed glass jars—are
able to explode and SHOULD NOT be HEATED
in this oven.
6. Use this equipment ONLY for its intended use as
described in this manual. Do not use corrosive
chemicals or vapors in this equipment. This type
(K/(;")/$*/*!"#$%#&<<?/4"*$1)"4/'(/:"&'L/#((ML/
or dry food. It is not designed for industrial or
laboratory use.
7. As with any equipment, CLOSE SUPERVISION
is necessary when used by CHILDREN.
,+/
11 DO NOT operate this equipment if it has a
damaged cord or plug, if it is not working properly,
or if it has been damaged or dropped.
12. This equipment, including power cord, must be
*"3;$#"4/HFIO/=?/A5&<$%"4/*"3;$#"/!"3*())"<+/
Special tools are required to service equipment.
Contact nearest authorized service facility for
examination, repair, or adjustment.
13. DO NOT cover or block louvers or other openings
on equipment.
14. DO NOT store this equipment outdoors. DO NOT
use this product near water – for example, near a
kitchen sink, in a wet basement, a swimming pool,
or a similar location.
15. DO NOT immerse cord or plug in water.
16. Keep cord AWAY from HEATED surfaces.
17. DO NOT let cord hang over edge of table or
counter.
6,+/ G(3/#(.."3#$&</5*"/()<?+
""/4((3/#<"&)$)1/$)*'35#'$()*/()/!&1"/E7N/(K/
this owners manual.
PRECAUTIONS TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
A. DO NOT attempt to operate this oven with the door open since open door operation can result in harmful
exposure to microwave energy. It is important not to defeat or tamper with the safety interlocks.
B. DO NOT place any object between the oven front face and the door too allow soil or cleaner residue to
accumulate on sealing surfaces.
C. DO NOT operate the oven if it is damaged. It is particularly important that the oven door close properly and
that there is no damage to the:
1. door (bent)
2. hinges and latches (broken or loosened)
3. door seals and sealing surfaces.
9+/ 0:"/(;")/*:(5<4/)('/="/&4>5*'"4/(3/3"!&$3"4/=?/&)?()"/"@#"!'/!3(!"3<?/A5&<$%"4/*"3;$#"/!"3*())"<+
SAVE THESE INSTRUCTIONS
5
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
0(/&;($4/3$*M/(K/%3"/$)/':"/(;")/#&;$'?Q
Liquids such as water, coffee, or tea are able to
be overheated beyond the boiling point without
appearing to be boiling due to surface tension of the
liquid. Visible bubbling or boiling when the container
is removed from the microwave oven is not always
present. THIS COULD RESULT IN VERY HOT
LIQUIDS SUDDENLY BOILING OVER WHEN A
SPOON OR OTHER UTENSIL IS INSERTED INTO
THE LIQUID. To reduce the risk of injury to persons:
a. DO NOT overcook food. Carefully attend oven
when paper, plastic, or other combustible
materials are placed inside the oven to facilitate
cooking.
b. Remove wire twist-ties from paper or plastic
bags before placing bag in oven.
c.
If materials inside the oven ignite, keep oven
door CLOSED, turn oven off and disconnect
the power cord, or shut off power at the fuse or
circuit breaker panel.
i)
ii)
Do not overheat the liquid.
Stir the liquid both before and halfway through
heating it.
iii) Do not use straight-sided containers with narrow
necks.
iv) After heating, allow the container to stand in the
microwave oven for a short time before removing
the container.
v) Use extreme care when inserting a spoon or
other utensil into the container.
d. DO NOT use the cavity for storage. DO NOT
leave paper products, cooking utensils, or food
in the cavity when not in use.
!
CAUTION
To avoid personal injury or property damage, observe the following:
1. Do not deep fat fry in oven. Fat could overheat
and be hazardous to handle.
9. Never use paper, plastic, or other combustible
materials that are not intended for cooking.
2. Do not cook or reheat eggs in shell or with
an unbroken yolk using microwave energy.
Pressure may build up and erupt. Pierce yolk
with fork or knife before cooking.
10. When cooking with paper, plastic, or other
combustible materials, follow manufacturer’s
recommendations on product use.
11. Do not use paper towels which contain nylon or
(':"3/*?)':"'$#/%="3*+/R"&'"4/*?)':"'$#*/#(5<4/
melt and cause paper to ignite.
3. Pierce skin of potatoes, tomatoes, and similar
foods before cooking with microwave energy.
When skin is pierced, steam escapes evenly.
12. Do not heat sealed containers or plastic bags in
oven. Food or liquid could expand quickly and
cause container or bag to break. Pierce or open
container or bag before heating.
4. Do not operate equipment without load or food
in oven cavity.
5. Microwave popcorn should not be popped in
oven.
13. To avoid pacemaker malfunction, consult
physician or pacemaker manufacturer about
effects of microwave energy on pacemaker.
6. Do not use regular cooking thermometers in
oven. Most cooking thermometers contain
mercury and may cause an electrical arc,
malfunction, or damage to oven.
14. An authorized servicer MUST inspect equipment
annually. Record all inspections and repairs for
future use.
7. Do not use metal utensils in oven.
,+/ 9(/)('/5*"/&<5.$)5./K($</$)/(;")
SAVE THESE INSTRUCTIONS
6
Installation
WARNING
Unpacking Oven
S/ T)*!"#'/(;")/K(3/4&.&1"/*5#:/&*/4")'*/$)/4((3/(3/
dents inside oven cavity.
S/ C"!(3'/&)?/4")'*/(3/=3"&M&1"/'(/*(53#"/(K/!53#:&*"/
immediately. Do not attempt to use oven if damaged.
S/ C".(;"/&<</.&'"3$&<*/K3(./(;")/$)'"3$(3+
S/ TK/(;")/:&*/="")/*'(3"4/$)/"@'3"."<?/#(<4/&3"&L/P&$'/&/
few hours before connecting power.
Excessive Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
Oven Placement
S/ 9(/)('/$)*'&<</(;")/)"@'/'(/(3/&=(;"/*(53#"/(K/:"&'L/
such as pizza oven or deep fat fryer. This could cause
microwave oven to operate improperly and could
shorten life of electrical parts.
S/ 9(/)('/=<(#M/(3/(=*'35#'/(;")/%<'"3+/E<<(P/&##"**/K(3/
cleaning.
S/ T)*'&<</(;")/()/<";"</#(5)'"3'(!/*53K&#"+
Radio Interference
Microwave operation may cause interference to radio,
television, or similar a oven. Reduce or eliminate
interference by doing the following:
S/ -<"&)/4((3/&)4/*"&<$)1/*53K&#"*/(K/(;")/&##(34$)1/'(/
instructions in “Care and Cleaning” section.
S/ 2<&#"/3&4$(L/'"<";$*$()L/"'#+/&*/K&3/&*/!(**$=<"/
from oven.
S/ U*"/&/!3(!"3<?/$)*'&<<"4/&)'"))&/()/3&4$(L/'"<";$*$()L/
etc. to obtain stronger signal reception.
A
B
C
Oven Clearances
A—For North American (UL/CSA) models, allow at least
2” (5.1 cm) of clearance around top of oven. For
International (50 Hz) models, allow at least 12” (30 cm)
(K/#<"&3&)#"/&3(5)4/'(!/(K/(;")+/23(!"3/&$3/V(P/&3(5)4/
oven cools electrical components. With restricted air
V(PL/(;")/.&?/)('/(!"3&'"/!3(!"3<?/&)4/<$K"/(K/"<"#'3$#&</
parts is reduced.
B—Allow at least 2” (5.1 cm) between air discharge on
back of oven and back wall.
C—Allow at least 2” (5.1 cm) of clearance around sides of
oven.
7
!"#$%#&'$()*
Models
RCS10DSE, MCS10DSE,
RCS10TS, MCS10TS
Power Source
Voltage AC
Amperage
Frequency
Single Phase, 3 wire grounded
2<51/-()%153&'$()/W/-(34/
Power Output
Nominal microwave energy
(IEC705)
Minimum temperature rise
Operating Frequency
Power Consumption
Cook Condition Microwave
Dimensions
Cabinet
Width
Height
Depth
Cavity Dimensions
Width
Height
Depth
Weight
Crated
Uncrated
120V
15 A
60 Hz
X
NEMA 5-20
1000 W
10°F / 5°C
2450 MHz
1550 W
22” (560)
13 ¾” (349)
68X/YN,BZ
14 ½X/Y[\,Z
,/½” (216)
6]X/Y[,6Z
47 lbs. (21.3 kg.)
N6/<=*+/Y6,+\/M1+Z
8
Quick Start Reference Guide (Electronic / Mechanical Dial)
Oven Wall Clearances
Menu Guide
A—For North American (UL/CSA) models, allow
at least 2” (5.1 cm) of clearance around top
of oven. For International (50 Hz) models,
allow at least 12” (30 cm) of clearance
A
B
2:00
:15
1:00 - 2:00
:45
:30
1:30 - 2:30
0
oven cools electrical components. With
C
properly and life of electrical parts is
reduced.
B—Allow at least 2” (5.1 cm) between air
discharge on back of oven and back wall.
C—Allow at least 2” (5.1 cm) of clearance around
sides of oven.
15
30
45
1
10
9
8
7
15
DO NOT power spray
30
45
2
6
5
4
3
So...how do I use it?
No metal pans
(Electronic / Mechanical Dial)
Heating
1.
2.
2.
3.
Open oven door, place food in oven, and close oven door.
Select desired power level or use default 100%.
Turn time entry knob clockwise to desired time.
Cooking time can be set up to 10 minutes.
Oven begins operation and time counts down.
When cooking time has elapsed, microwave energy stops and oven signal sounds.
Interrupting Operation
20%
50%
70% 100%
Open oven door to interrupt operation or turn time entry knob counterclockwise to “0”.
To resume microwave oven operation, close door, select power level pad, and turn knob.
Changing Time and Canceling Mistakes
20%
50%
Heating time and power level can be changed at any time while the oven is operating.
Press power level pad or turn knob to desired new setting. To set cooking time to zero,
turn knob counterclockwise to “0” or cycle door open and closed.
Changing Timer Option
Timer resetting to zero can be set at any time to pause current cook time and power level when door is
opened. To change this option follow the step below.
70%
100%
With door open press and hold the 100% pad 100% for 5 seconds until beep is heard. Close the
door this changes timer setting to pause current cook time and power level when door is opened.
Timer pausing current cook time and power level can be set at any time to reset to zero and 100%
power level when door is opened. To change this option follow the step below.
With door open press and hold the 20% pad 20% for 5 seconds until beep is heard. Close
the door this changes timer setting to reset timer to zero and power level to 100% when door is
opened.
The switching operation of this microwave oven can cause voltag
der unfavorable voltage
supply conditions can have adverse effects. This device is intended for the connection to a power supply system with a maximum permissible system
impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to ensure that this device is connected only to a power
at
the interface point.
9
Quick Start Reference Guide (Electronic Control)
Oven Wall Clearances
A—For North American (UL/CSA) models, allow at least
2” (5.1 cm) of clearance around top of oven. For
International (50 Hz) models, allow at least 12” (30
cm) of clearance around top of oven. Proper air
;!3",1!'*&"!5.*"#!!4(".4.#01)#,4"#!2-!*.*0(="O)0<"
1.(01)#0.&",)1";!3?"!5.*"2,9"*!0"!-.1,0."-1!-.149",*&"
life of electrical parts is reduced.
B—Allow at least 2” (5.1 cm) between air discharge on
back of oven and back wall.
C—Allow at least 2” (5.1 cm) of clearance around sides
of oven.
A
B
C
So...how do I use it?
(Electronic Control)
Manual Operation
!"#!!$"%!!&"'()*+","(-.#)/#".*0.1.&"0)2.",*&"-!3.1"4.5.46
Preprogrammed
Pads
To cook food using
preprogrammed cooking
sequences:
1. Open oven door and place food
in oven. Close door.
2. Press desired pad.
3. Oven begins to cook.
4. At end of cooking cycle oven
beeps and shuts off.
X2 Programming
1. Open oven door and place food in oven. Close door.
pad and enter cooking time.
2. Press TIME ENTRY
3. Press a power level pad to change power level if desired (some
models).
7" COOK LEVEL displays with the power setting.
4. If stage cooking is desired, press TIME ENTRY
2 through 4.
pad and repeat steps
5. Press START
pad.
6. At end of cooking cycle oven beeps and shuts off.
Programming Items
1.
2.
3.
4.
Open oven door.
Press and hold pad 1 for approximately 5 seconds.
Press pad to be reprogrammed.
Enter cooking time by using the number pads.
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Press the X2 pad.
5. Press a numbered pad to
change the cooking factor.
7" J!!$)*+"%,#0!1"#,*":."(.0"%1!2"
10% to 100%.
7" 8.%,'40")("IKL=
7" M,&"N"3!'4&"#<,*+."0<."
cooking factor to 50%.
6. Press START
changes.
pad to save
5. Press a power level
pad to change power level if desired.
pad.
6. If stage cooking is desired, press TIME ENTRY
7" 8)(-4,9":1).;9"(<!3("0<."(0,+."*'2:.1=
7" 8)(-4,9"#<,*+.("0!"#!!$"0)2.",*&"-!3.1"4.5.4"%!1"0<."*.>0"(0,+.=
7. Enter cook time and power level as in steps 4 and 5 (some models).
7" !".*0.1",*!0<.1"#!!$)*+"(0,+."%!1"0<,0"-,&?"-1.((" @AB"BC DE"
again.
7" F-"0!"%!'1"&)%%.1.*0"(0,+.("#,*":."-1!+1,22.&"G(!2."2!&.4(H=
I=" Press START
pad to set new programming changes to the pad.
NOTE: To discard changes, press STOP/RESET
pad or close oven door.
X2 Pad
1.
2.
3.
4.
Open oven door and place food in oven. Close door.
Press X2 pad.
Press desired preprogrammed pad or pad sequence.
Oven begins cooking. Displayed cooking time is the total of original
cooking time and added X2 time.
10
pad
Quick Start Reference Guide (Electronic Control)
Can I change an option?
Options such as single or double pad programming, beep volume, and
maximum cooking time can be changed to suit individual preferences.
To change options:
1. Open oven door.
pad is pressed before programming is
7" @%"&!!1")("#4!(.&"!1"P QMRDBPB "
complete, changes are discarded and microwave exits programming mode.
2. Press and hold pad 2 for approximately 5 seconds.
7" <)(":.+)*("!-0)!*("2!&.=
7" A)#1!3,5."3)44":..-",*&"0P: displays.
3. Press number pad that controls option to be changed.
7" P.."0,:4.":.4!3"%!1"!-0)!*(=
7" J'11.*0"!-0)!*"3)44"&)(-4,9=
4. Press number pad again to change the option.
7" B,#<"0)2."-,&")("-1.((.&?"!-0)!*"3)44"#<,*+.=
7" A,0#<"#!&."&)(-4,9.&"3)0<"#!&."%!1"&.()1.&"!-0)!*=
DO NOT power spray
No metal pans
5. Press START
pad to save changes.
7" !"#<,*+.",&&)0)!*,4"!-0)!*(?"1.-.,0"(0.-("S",*&"T=
7" J<,*+.(",--.,1",%0.1"&!!1")("#4!(.&"!1"P QMRDBPB "
Numbered Pads
1
End of Cycle Beep
Display
Options (Factory Settings in Bold)
OP:10
3 second beep.
OP:11
Continuous beep until door is opened.
OP:12
5 beep bursts until door is opened.
2
OP:20
Eliminates beep.
Key Beep Volume
OP:21
Sets volume to low.
OP:22
Sets volume to medium.
3
Key Beep
4
Active Display
OP:23
Sets volume to high.
OP:30
Prevents beep when pad is pressed.
OP:31
Allows beep when pad is pressed.
OP:40
15 seconds after oven door is opened, keyboard disabled.
OP:41
30 seconds after oven door is opened, keyboard disabled.
OP:42
1 minute after oven door is opened, keyboard disabled.
OP:43
2 minutes after oven door is opened, keyboard disabled.
5
OP:50
Prevents different pre-programmed pads to be activated during cooking.
On-the Fly Cooking
OP:51
Allows different pre-programmed pads to be activated during cooking.
6
OP:60
Opening oven door does not reset oven back to ready mode.
OP:61
Opening oven door resets oven back to ready mode.
OP:70
Allows 60 minutes of heating time (some models).
OP:71
Allows 10 minutes of heating time.
OP:80
Allows use of preprogrammed pads only.
Reset to Ready Mode
7
(some models)
Maximum Heating Time
8
Manual Operation
9
(some models)
OP:81
Allows use of manual time entry and preprogrammed pads.
OP:90
Allows 10 (0-9) preprogrammed pads.
OP:91
Allows 100 (00-99) preprogrammed pads.
Double Digit Operation
0
Clean Filter Message
OP:00
Do not display message.
OP:01
Display message for 24 hours every 7 days.
OP:02
Display message for 24 hours every 30 days.
OP:03
Display message for 24 hours every 90 days.
11
pad is pressed.
Components Location (Oven Cavity)
19
2
3
1
20
4
5
25
18
7
6
8
17
27
9
22
23
16
13 12
14
15
10
21
11
26
24
Reference
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Part Number
12002625
54127062
54127037
54127062
56002013
B5667304
14114048
54127038
54116025
54127064
54127061
54127015
54127001
54127011
54127064
54127061
54127029
54127019
54127045
54127064
54127042
53001724
20036801
R0000413
54116064
54116021
54127066
12
Description
KIT, COVER / STIRRER BLADE/ RIVETS
SCREW
THERMAL CUTOUT, CAVITY
SCREW
MOTOR, ANTENNA
CLIP -WIRE
MAGNETRON
THERMAL CUTOUT, MAG
SCREW
SCREW
SCREW
CAPACITOR- 1.05
BASEPAN ASSY
TRANSFORMER HV
SCREW
SCREW
HINGE, LOWER
TRAY, CERAMIC
WRAPPER
SCREW
HARNESS, MAIN
BRACKET, CAPACITOR
DIODE
BASEPAN GASKET
RIVET ASSY
SCREW
SCREW
Quantity
1
1
1
1
1
2
1
1
2
1
4
1
1
1
3
2
1
1
1
4
1
1
1
1
1
4
1
Components Location (Blower / Interlock)
6
7
5
3
4
2
1
12
8
11
10
9
1
14
15
13
16
Reference
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part Number
54116017
54127039
54127049
54116017
54116017
54127009
54116017
54127048
54116017
54127040
54127036
20034003
54127065
54127056
56112070
54127059
Description
SCREW
DUCT, MAG
LAMP / SOCKET ASSY
SCREW
SCREW
INTERLOCK SWITCH ASSY
SCREW
POWER CORD
SCREW
BRKT, INLET AIR
FUSE BLOCK / FILTER ASSY
FUSE
SCREW
MOTOR, BLOWER & BLADE
BLADE, FAN
BRKT, BLOWER
13
Quantity
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
Components Location (Dial Control)
2
1
3
4
5
6
7
Reference
1
2
2
3
3
4
5
6
7
Part Number
54127053
54127002
54127004
54127031
54127054
54127067
54127030
54127067
54127032
Description
KNOB
ESC / TOUCH PANEL ASSY (RCS10DSE)
ESC / TOUCH PANEL ASSY (MCS10DSE)
BOARD, LED (RCS10DSE)
BOARD, LED (MCS10DSE)
SCREW
BOARD, HV / LV
SCREW
HARNESS, PCB
14
Quantity
1
1
1
1
1
5
1
4
1
Components Location (Electronic Control)
1
2
3
Reference
1
1
2
3
Part Number
54127003
54127005
54127033
54127067
Description
ESC / TOUCH PANEL ASSY (RCS10TS)
ESC / TOUCH PANEL ASSY (MCS10TS)
BOARD, HV / LV
SCREW
15
Quantity
1
1
1
4
Components Location (Door)
4
7
6
5
1
2
8
3
Reference
1
1
2
3
4
5
6
7
8
Part Number
54127021
54127023
14124068
14124069
54127027
54127028
54127061
54127064
54127063
Description
DOOR ASSY (RCS10*)
DOOR ASSY (MCS10*)
KIT, SPRING/LATCH/CHOKE COVER
KIT, DOOR HANDLE
WINDOW, INNER
HINGE, UPPER
SCREW
SCREW
SCREW
16
Quantity
1
1
1
1
1
1
2
1
2
Performance Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death, disconnect power to oven and discharge capacitor
before servicing, unless testing requires it.
All Amana and Menumaster microwave oven power outputs are rated using the IEC705 standards. Using the
IEC705 test method requires precision measurements and equipment that is not practical to be performed in the
field. Using the test shown below will indicate if the oven performance is satisfactory.
Test equipment required:
1000 ml test container and thermometer.
Digital watch / watch with a second hand for use on ovens with electromechanical timers.
Important Notes:
Low line voltage will cause low temperature rise / power output.
Ovens must be on a dedicated circuit, properly grounded, and polarized. Other equipment on the same
circuit may cause a low temperature rise / power output.
This test and results are not a true IEC705 test procedures and are only intended to provide servicers with
an easy means of determining if the microwave oven cooking output is correct.
Procedure
1. Fill the test container to the 1000 ml line with cool tap water.
NOTE:
Water temperature should be approximately 60!F / 16!C
2. Using the thermometer, stir water for five to ten seconds; measure, and record the temperature (T1).
3. Place test container of water in the center of oven cavity and close door.
4. Heat the water for a 33-second full power cycle.
NOTE:
Use a digital watch or a watch with a second hand for ovens with electromechanical timers.
5. At end of the cycle, remove test container. Using the thermometer, stir water for five to ten seconds and record
temperature (T2).
6. Subtract the starting water temperature (T1), from the ending water temperature (T2) to obtain the temperature
rise ( T).
7. If the temperature rise ( T) meets or exceeds the minimum, the test is complete. If the temperature rise ( T)
fails to meet the minimum temperature rise, test the line voltage to verify it is correct. Then repeat steps 1 - 6
making sure to change the water. If the temperature rise ( T) fails to meet the minimum temperature rise again
the oven will require service.
Minimum Temperature Rise at Thirty -Three (33) Seconds Run Time
T
(°F)
Cooking
Power Output
10 ................. 1000
11 ................. 1100
12 ................. 1200
14 ................. 1400
17 ................. 1700
18 ................. 1800
19 ................. 1900
T
(°F)
Cooking
Power Output
T
(°C)
20 ................. 2000
21 ................. 2100
22 ................. 2200
24 ................. 2400
25 ................. 2500
27 ................. 2700
30 ................. 3000
Cooking
Power Output
5 .............. 1000
5.5 ............ 1100
6.5 ............ 1200
7.5 ............ 1400
9.5 ............ 1700
10 ............. 1800
10.5 .......... 1900
17
T
(°C)
Cooking
Power Output
11............ 2000
11.5......... 2100
12............ 2200
13............ 2400
13.5......... 2500
15............ 2700
16.5......... 3000
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.
I l l u s tr a ti o n
C o m po n en t
Thermal cutout
Diode
Capacitor
T e s ti n g
R e s u l ts
Disconnect all wires from TCO.
Measure resistance across terminals.
Cavity TCO ................................................................ Opens at 212ºF (100ºC)
Magnetron TCO ...................................................... Closed at 140ºF (60ºC) and
Opens at 320ºF (160ºC)
Infinite resistance should be
Discharge Capacitor
measured in one direction and 50K Ω
Remove diode lead from capacitor and
or more in the opposite direction.
connect ohmmeter.
NOTE: Ohmmeter must contain a
Reverse leads for second test.
battery of 6 volts minimum.
Discharge Capacitor
Remove wires from capacitor terminals
and connect ohmmeter, set on highest
resistance scale to terminals.
Magnetron
Also check between each terminal and
capacitor case.
Discharge Capacitor
Remove wires from magnetron and
connect ohmmeter to terminals. Also
check between each terminal and
ground.
Blower motor
Between Terminals: Meter should
momentarily deflect towards zero
then return to over 5 M Ω . If no
deflection occurs, or if continuous
deflection occurs, replace capacitor.
Terminal to Case: Infinite resistance
Ω
Between Terminals: Less than 1
Each terminal to ground measures
Infinite resistance.
Note: This test is not conclusive. If
oven does not heat and all other
components test good replace the
magnetron and retest.
Remove all wires from motor.
Measure resistance across coil............................. Approximately 44 Ω
Stirrer motor
Remove all wires from motor.
Measure resistance across terminals................ Approximately 3.8K Ω
Transformer
Secondary
Filament
Primary
Lamp and receptacle
W ire H a rne s s
Discharge Capacitor
Remove all wires from terminals.
Measure resistance from:
Primary .....................................................................
Filament....................................................................
Secondary to Ground screw on
transformer stack.................................
Test continuity of receptacle terminals.
T e s t c ontinuity of wire s
18
Less than <1 Ω
Less than <1 Ω
Approximately 75 Ω
Indicates continuity with bulb
installed.
I ndic a te s c ontinuity
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.
I l l u s tr a ti o n
C o m po n en t
Fuse block / Filter assembly
Interlock switch assembly
(Mechanical)
1
2
PRIMARY
INTERLOCK SWITCH
3
4
MONITOR
INTERLOCK SWITCH
5
6
SECONDARY
INTERLOCK SWITCH
T e s ti n g
R e s u l ts
Power In terminals ...................................................... 120 VAC
Power Out terminals ................................................... 120 VAC
If no power in, check power outlet
If no power out, check fuses
Disconnect wires to switch.
With door open measure resistance from:
Monitor – Terminals 3 - 4 .............................. Indicates continuity
Primary – Terminals 1 - 2................................ Infinite Ω
Secondary – Terminals 5 - 6 .......................... Infinite Ω
With door closed measure resistance
from:
Monitor – Terminals 3 - 4 ............................... Infinite Ω
Primary – Terminals 1 - 2................................ Indicates continuity
Secondary – Terminals 5 - 6 .......................... Indicates continuity
After verifying or replacing the module,
re-connect wires to switch and check
operation of monitor circuit before
operating the oven.
(CN3)
Dial Electronic control
1.
(CN1 connector) Measure voltage at
BN (1) and BL (3) terminal leads ............. Approximately 120 VAC
2.
(Relay 1) Measure voltage across
BL and WH terminal leads ......................... 120 VAC OFF position (Door
Closed)
0 volts Cook mode (Door Closed)
(Relay 2) Measure voltage across
BL and WH terminal leads............................ 120 VAC OFF position (Fan/Light
Off)
0 volts (Fan/Light ON)
3.
Relay 2
1
(CN1)
3 4
6 7
Relay 1
19
Troubleshooting
Service Diagnostics
Control does not power up
12"34 5%6 +/)" (%+78-"
9"7:"") 72" :2/7" 8).
9+834 :/6" %) 72" /)+"7
#/." %5 72" 5/+7"6 9%86.;
!"#
&# '(") *+,--". /)0
$%
!"#
12"34 5%6 +/)"
(%+78-" 9"7:"")
72" 9+,"<:2/7"
8). 9+834 :/6"# %)
72" %,7+"7 #/." %5
72" 5/+7"6 9%86.;
12"34 5,#" %) 5/+7"6
9%86. 8). 6"=+83"
8# )"".".;
$%
!"#
G"=+83" .%%6 #:/732 8##"H9+E
!"#
12"34 %(") D1' 7%
")#,6" /7 28# 3%)7/),/7E;
$%
G"=+83" '(") D1'
!"#
$%
12"34 F8-)"76%) D1' 5%6
3%)7/),/7E
!"#
12"34 5%6 +/)" (%+78-"
87 1$> =/) > ?@6%:)A B
=/) C ?@+,"A
G"=+83" F8-)"76%) D1'
$%
12"34 5%6 3%)7/),/7E
%5 :/6"# %6 8 98. :/6"
3%))"37%6
!"#
1%)76%+ /# ."5"37/(" 8).
)"".# 7% 9" 6"=+83".;
20
*+,- %(") /)
Troubleshooting
Service Diagnostics
!"#$!%&'!()$*&+',&-+#&"!&.)/#&
0.)"&#.)&!1)"&2*&'%+33)4&2"&2*&#.)$)&&
55&5555&*.!(2"3&2"&#.)&42*'%/6&
No
7))&*)$128)&42/3"!*#28*&9&
"!&'!()$&
Yes
:')"&4!!$,&4!)*&!1)"&%23.#&/"4&
;/"&8!<)&!"&
.)8=&4!!$&*(2#8.&/**)<-%6,&
/4>+*#&!$&$)'%/8)&/*&"))4)4?&
No
Yes
%!*)&4!!$&/"4&8!"#$!%&
*.!+%4&*/6&$)/46&
.)8=&4!!$&*(2#8.&/**)<-%6,&/4>+*#&!$&
$)'%/8)&/*&"))4)4?&
No
Yes
@+*.&#2<)&=)6,&)"#)$A&BC&*)8!"4*&
.)8=&=)6&'/4&$2--!"&8!"")8#!$&
#!&)"*+$)&2#&2*&8!"")8#)4&
No
Yes
@+*.&#.)&3$))"&*#/$#&&&
-+##!",&4!)*&#2<)$&8!+"#&
4!("?&
Yes
D)6&'/4&/**)<-%6&
"))4*&#!&-)&$)'%/8)4&
No
Yes
.)8=&;!$&%2")&1!%#/3)&/8$!**&#.)&-%+)&
/"4&-%/8=&%)/4*&!"&#.)&'$2</$6&*24)&
!;&#.)&EF&#$/"*;!$<)$&
No.)8=&(2$)&8!"#2"+2#6&/"4&#)$<2"/%*&
Yes
G.)&EFHIF&$)%/6&-!/$4&
"))4*&#!&-)&$)'%/8)4&
Yes
No
02#.&'!()$&42*8!"")8#)4,&8.)8=&;!$&J&B&
!.<*&$)*2*#/"8)&/8$!**&#.)&'$2</$6&8!2%?&
EF&#$/"*;!$<)$&"))4*&
#!&-)&$)'%/8)4&
Yes
02#.&'!()$&42*8!"")8#)4&8.)8=&;!$&
/''$!K2</#)%6&LC&!.<*&;$!<&#.)&
*)8!"4/$6&(2$)&#!&3$!+"4&*8$)(?&
No
EF&#$/"*;!$<)$&"))4*&#!&-)&
$)'%/8)4&
Yes
.)8=&8/'/82#!$,&(2#.&<)#)$&*)#&!"&#.)&
.23.)*#&!.<&*8/%),&<)#)$&*.!+%4&$)/4&M)$!,&
#.)"&$)#+$"&#!&!1)$&NC<&!.<*?&&
No
O)'%/8)&8/'/82#!$&
Yes
G)*#&42!4),&(2#.&<)#)$&*)#&!"&!.<*&*8/%),&
*.!+%4&-)&2";2"2#),&*(2#8.&%)/4*&/"4&*.!+%4&
$)/4&NC=&!.<*&2"&!")&42$)8#2!"?&
No
21
O)'%/8)&42!4),&)"*+$)&/&3!!4&#23.#&3$!+"4&
Schematic / Wiring Diagram RCS10* / MCS10*
22
Notes:
23
Part No. 16400020
!"#$%&'"#'()*)+)',-./0
www.acpsolutions.com
2012 ACP Inc.
Cedar Rapids, Iowa 52404