Stylus C60 - Start Here Card

EPSON Stylus C60
®
Start
Here
Start
Here
1
1
1
Unpack
3
1
2
Power On
power button
Plug the printer into a grounded electrical outlet.
Press the
power button to turn on the printer.
Don’t turn on your computer yet.
Remove everything from the box.
Don’t use an outlet controlled by a wall switch or timer. Never use a power strip switch
to turn the printer on or off; use only the printer’s
power button.
printer
2
3
3
paper support
ink cartridges
CD-ROM
Printer Basics
Remove all the tape and
packing material.
4
4 Load Ink
1
Open the output tray and raise the printer cover.
2
Peel off tape and remove the insert.
1
remove the
insert
2
4
Lift up the ink cartridge clamps.
Fit the paper support
into its three slots.
You must install both cartridges or the printer won’t work.
3
2
2
Unpack the ink cartridges that came with your printer and remove the yellow tape.
Don’t remove the seals from the
bottom of the cartridges; ink will
leak out.
Connect the Printer
Connect the printer to your computer using either a USB cable or parallel cable. Don’t connect both
cables; you only need one or the other. Follow the instructions in the appropriate section below.
Keep cartridges out of the reach
of children.
If You Have a USB Port
(Does not support Windows® 95.)
1
2
3
Make sure the printer and computer are turned off.
Connect the
Connect the
4
Tilt each cartridge toward you as you lower it. Make sure the tabs rest on the hooks.
square end of the USB cable to your printer’s USB port.
black
flat end of the cable to any available USB port on your computer.
color
Don’t place the cartridge tabs
under the hooks, or you may
damage the clamp when you
close it.
hooks
5
Lower the clamps so they snap shut.
6
Press the
ink replacement button and close the printer cover. You see the
green
power light flash and you hear the printer make noise.
If You Have a PC Parallel Port
1
2
3
ink replacement
button
Make sure the printer and computer are turned off.
Connect the larger end of the parallel cable to your printer’s parallel port.
Then secure it with the wire clips.
Connect the other end of the cable to your computer’s parallel port and secure it as necessary.
Don’t turn off the printer or interrupt ink charging while the
power light is
flashing or you’ll use up more ink than necessary when you turn it back on.
7
Wait until ink charging is finished (the green
power light stops flashing).
Turn over
EPSON Stylus C60
®
Start
Here
Start
Here
1
1
1
Unpack
3
1
2
Power On
power button
Plug the printer into a grounded electrical outlet.
Press the
power button to turn on the printer.
Don’t turn on your computer yet.
Remove everything from the box.
Don’t use an outlet controlled by a wall switch or timer. Never use a power strip switch
to turn the printer on or off; use only the printer’s
power button.
printer
2
3
3
paper support
ink cartridges
CD-ROM
Printer Basics
Remove all the tape and
packing material.
4
4 Load Ink
1
Open the output tray and raise the printer cover.
2
Peel off tape and remove the insert.
1
remove the
insert
2
4
Lift up the ink cartridge clamps.
Fit the paper support
into its three slots.
You must install both cartridges or the printer won’t work.
3
2
2
Unpack the ink cartridges that came with your printer and remove the yellow tape.
Don’t remove the seals from the
bottom of the cartridges; ink will
leak out.
Connect the Printer
Connect the printer to your computer using either a USB cable or parallel cable. Don’t connect both
cables; you only need one or the other. Follow the instructions in the appropriate section below.
Keep cartridges out of the reach
of children.
If You Have a USB Port
(Does not support Windows® 95.)
1
2
3
Make sure the printer and computer are turned off.
Connect the
Connect the
4
Tilt each cartridge toward you as you lower it. Make sure the tabs rest on the hooks.
square end of the USB cable to your printer’s USB port.
black
flat end of the cable to any available USB port on your computer.
color
Don’t place the cartridge tabs
under the hooks, or you may
damage the clamp when you
close it.
hooks
5
Lower the clamps so they snap shut.
6
Press the
ink replacement button and close the printer cover. You see the
green
power light flash and you hear the printer make noise.
If You Have a PC Parallel Port
1
2
3
ink replacement
button
Make sure the printer and computer are turned off.
Connect the larger end of the parallel cable to your printer’s parallel port.
Then secure it with the wire clips.
Connect the other end of the cable to your computer’s parallel port and secure it as necessary.
Don’t turn off the printer or interrupt ink charging while the
power light is
flashing or you’ll use up more ink than necessary when you turn it back on.
7
Wait until ink charging is finished (the green
power light stops flashing).
Turn over
5
6
5
Macintosh
1
Load Paper
®
Make sure the printer is turned on, then turn on your Macintosh.
1
Load some paper behind the tabs
inside the edge guides.
1
When you see your Macintosh icons, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
2
Press in the locking tab on the left edge guide
and slide it to the edge of the paper stack.
2
Double-click the
EPSON CD-ROM icon,
then double-click the
EPSON icon.
3
Pull out the output tray extension.
3
4
5
Read the license agreement and click Agree.
If you’re using Windows , check to see which version you have.
Then follow the right set of instructions for your system.
6
Select your default paper size, then click Restart. After your
Macintosh restarts, you see the EPSON Registration screen.
Windows 95, 98, Me, and 2000
7
8
Register your printer as instructed.
2
3
6 Install Software
®
Your computer may have the EPSON printer software already installed.
Make sure the printer is turned on, then turn on your computer.
9
If you see this message
Your software is already installed. Click OK. You’re ready to start
printing! Or, go to section 7 to install optional programs.
If you see this screen
Click Cancel. Then follow the steps below to install the
printer software:
1
When you see the Windows icons on your monitor, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
At the Main Menu, click Install Printer Driver.
At the installer screen, click Install; then click Continue
on the next screen. The files are copied to your Macintosh.
Open the Chooser, click the C60 Series icon, click your USB port,
and turn on background printing.
Close the Chooser.
Now you’re ready to install optional programs.
Go to section 7.
7
7
Install Optional Programs
1
After you register your printer, you see the Main Menu.
If you don’t see the Main Menu, open your CD-ROM window,
then double-click the
EPSON icon.
2
3
Click Install EPSON Film Factory. You see this screen:
4
Click Install Printer Movies and Manual and follow the
instructions on the screen. When installation is complete,
click Exit or Quit to return to the Main Menu.
2
Double-click
My Computer, double-click
then double-click
EPSON.
3
4
Read the license agreement and click Agree.
5
If you see a screen asking you to turn on the printer, make
sure the printer is connected and turned on. Wait a minute
until the screen disappears. Do not click Stop searching.
More files are copied.
6
When setup is complete, click OK.
The EPSON Product Registration screen appears.
5
Click Share Photos Online at EPSON PhotoCenter.
You see this screen:
7
Register your printer as instructed.
At the last screen, click Done or close your browser.
6
If you want to place a link to the EPSON PhotoCenter
website on your desktop, click Add Icon. Click OK,
then click Back to return to the Main Menu.
7
Click Exit, then remove the CD-ROM.
EPSON,
At the Main Menu, click Install Printer Driver.
The files are copied to your computer.
Now you’re ready to install optional programs.
Go to section 7.
Windows XP
Your computer may have the EPSON printer software already installed.
Make sure the printer is turned on, then turn on your computer.
If you see a message that
your new hardware is installed and ready,
you can start printing right away. Or, go to section 7 to install
optional programs.
If you see this screen
SM
8
8 Print
Now that you’ve set up your printer, you’re ready to print.
See your Printer Basics book for instructions.
Or, double-click the
EPSON Printer Information Center icon
on your desktop (installed in section 7). You see this screen.
Click Reference Guide to view detailed information about your
printer. Click Print Show to view helpful animations that show
you how to print, load paper and ink, and solve basic problems.
Click Cancel. Then follow the steps below to install the
printer software:
1
When you see the Windows icons on your monitor, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
2
If you see a screen asking What do you want
Windows to do?, click Cancel.
3
Click Start, click
then double-click
4
5
Read the license agreement and click Agree.
My Computer, double-click
EPSON.
Click Install, then follow the instructions on the screen.
When installation is complete, close any open windows,
then click Back to return to the Main Menu.
EPSON,
At the Main Menu, click Install Printer Driver.
Wait while the files are copied to your computer.
6
If you see this screen, make sure the printer is connected
and turned on, then click Stop searching. More files
are copied.
7
When you see a message that setup is complete or the printer
port has been set, click OK. The EPSON Product Registration
screen appears.
8
Register your printer as instructed.
At the last screen, click Done or close your browser.
Now you’re ready to install optional programs.
Go to section 7.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.
EPSON PhotoCenter is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only
and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2001 by Epson America, Inc.
Printed on recycled paper. 9/01
Printed in USA
CPD-12569R2
4014103-00
5
6
5
Macintosh
1
Load Paper
®
Make sure the printer is turned on, then turn on your Macintosh.
1
Load some paper behind the tabs
inside the edge guides.
1
When you see your Macintosh icons, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
2
Press in the locking tab on the left edge guide
and slide it to the edge of the paper stack.
2
Double-click the
EPSON CD-ROM icon,
then double-click the
EPSON icon.
3
Pull out the output tray extension.
3
4
5
Read the license agreement and click Agree.
If you’re using Windows , check to see which version you have.
Then follow the right set of instructions for your system.
6
Select your default paper size, then click Restart. After your
Macintosh restarts, you see the EPSON Registration screen.
Windows 95, 98, Me, and 2000
7
8
Register your printer as instructed.
2
3
6 Install Software
®
Your computer may have the EPSON printer software already installed.
Make sure the printer is turned on, then turn on your computer.
9
If you see this message
Your software is already installed. Click OK. You’re ready to start
printing! Or, go to section 7 to install optional programs.
If you see this screen
Click Cancel. Then follow the steps below to install the
printer software:
1
When you see the Windows icons on your monitor, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
At the Main Menu, click Install Printer Driver.
At the installer screen, click Install; then click Continue
on the next screen. The files are copied to your Macintosh.
Open the Chooser, click the C60 Series icon, click your USB port,
and turn on background printing.
Close the Chooser.
Now you’re ready to install optional programs.
Go to section 7.
7
7
Install Optional Programs
1
After you register your printer, you see the Main Menu.
If you don’t see the Main Menu, open your CD-ROM window,
then double-click the
EPSON icon.
2
3
Click Install EPSON Film Factory. You see this screen:
4
Click Install Printer Movies and Manual and follow the
instructions on the screen. When installation is complete,
click Exit or Quit to return to the Main Menu.
2
Double-click
My Computer, double-click
then double-click
EPSON.
3
4
Read the license agreement and click Agree.
5
If you see a screen asking you to turn on the printer, make
sure the printer is connected and turned on. Wait a minute
until the screen disappears. Do not click Stop searching.
More files are copied.
6
When setup is complete, click OK.
The EPSON Product Registration screen appears.
5
Click Share Photos Online at EPSON PhotoCenter.
You see this screen:
7
Register your printer as instructed.
At the last screen, click Done or close your browser.
6
If you want to place a link to the EPSON PhotoCenter
website on your desktop, click Add Icon. Click OK,
then click Back to return to the Main Menu.
7
Click Exit, then remove the CD-ROM.
EPSON,
At the Main Menu, click Install Printer Driver.
The files are copied to your computer.
Now you’re ready to install optional programs.
Go to section 7.
Windows XP
Your computer may have the EPSON printer software already installed.
Make sure the printer is turned on, then turn on your computer.
If you see a message that
your new hardware is installed and ready,
you can start printing right away. Or, go to section 7 to install
optional programs.
If you see this screen
SM
8
8 Print
Now that you’ve set up your printer, you’re ready to print.
See your Printer Basics book for instructions.
Or, double-click the
EPSON Printer Information Center icon
on your desktop (installed in section 7). You see this screen.
Click Reference Guide to view detailed information about your
printer. Click Print Show to view helpful animations that show
you how to print, load paper and ink, and solve basic problems.
Click Cancel. Then follow the steps below to install the
printer software:
1
When you see the Windows icons on your monitor, put the
EPSON CD-ROM in your CD-ROM or DVD drive.
2
If you see a screen asking What do you want
Windows to do?, click Cancel.
3
Click Start, click
then double-click
4
5
Read the license agreement and click Agree.
My Computer, double-click
EPSON.
Click Install, then follow the instructions on the screen.
When installation is complete, close any open windows,
then click Back to return to the Main Menu.
EPSON,
At the Main Menu, click Install Printer Driver.
Wait while the files are copied to your computer.
6
If you see this screen, make sure the printer is connected
and turned on, then click Stop searching. More files
are copied.
7
When you see a message that setup is complete or the printer
port has been set, click OK. The EPSON Product Registration
screen appears.
8
Register your printer as instructed.
At the last screen, click Done or close your browser.
Now you’re ready to install optional programs.
Go to section 7.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.
EPSON PhotoCenter is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only
and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2001 by Epson America, Inc.
Printed on recycled paper. 9/01
Printed in USA
CPD-12569R2
4014103-00