Carrier AQUAZONE 50VQP084-300 Instruction manual

AQUAZONE™
50VQP084-300
Vertical Large Capacity Water Source Heat Pumps
with PURON® Refrigerant (R-410A)
50 Hz
Installation, Start-Up, and
Service Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . .1,2
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Step 1 — Check Jobsite . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 2 — Check Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
• STORAGE
• PROTECTION
• INSPECT UNIT
Step 3 — Locate Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Step 4 — Mount the Unit . . . . . . . . . . . . . . . . . . . . . . . . . 6
• DISCHARGE CONFIGURATION CONVERSION
• CONTROL BOX/MOTOR ACCESS
CONFIGURATION CONVERSION
Step 5 — Check Duct System . . . . . . . . . . . . . . . . . . . . 9
• SOUND ATTENUATION
• EXISTING DUCT SYSTEM
Step 6 — Install Condensate Drain . . . . . . . . . . . . . . . 9
• VENTING
Step 7 — Pipe Connections . . . . . . . . . . . . . . . . . . . . . 10
• WATER LOOP APPLICATIONS
• GROUND-LOOP APPLICATIONS
• GROUND-WATER APPLICATIONS
Step 8 — Wire Field Power Supply . . . . . . . . . . . . . . 11
• POWER CONNECTION
• SUPPLY VOLTAGE
• 420-VOLT OPERATION
Step 9 — Wire Field Controls. . . . . . . . . . . . . . . . . . . . 17
• THERMOSTAT CONNECTIONS
• WATER FREEZE PROTECTION
• AIR COIL FREEZE PROTECTION
• ACCESSORY CONNECTIONS
• WATER SOLENOID VALVES
PRE-START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-32
System Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Airflow and External Static Pressure . . . . . . . . . . . 18
FIELD SELECTABLE INPUTS . . . . . . . . . . . . . . . .33,34
Complete C Control Jumper Settings. . . . . . . . . . . 33
Complete C Control DIP Switches. . . . . . . . . . . . . . 33
Deluxe D Control Jumper Settings . . . . . . . . . . . . . 33
Deluxe D Control DIP Switches . . . . . . . . . . . . . . . . 33
Deluxe D Control Accessory Relay
Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-36
Operating Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Start Up System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Scroll Compressor Rotation. . . . . . . . . . . . . . . . . . . . . 34
Unit Start-Up Cooling Mode . . . . . . . . . . . . . . . . . . . . . 35
Unit Start-Up Heating Mode . . . . . . . . . . . . . . . . . . . . . 35
Flow Regulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Page
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cooling Tower/Boiler Systems . . . . . . . . . . . . . . . . . . 36
Ground Coupled, Closed Loop and Plateframe
Heat Exchanger Well Systems . . . . . . . . . . . . . . . . 36
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36,37
Power Up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Units with Aquazone Complete C Control . . . . . . . 37
Units with Aquazone Deluxe D Control . . . . . . . . . . 37
COMPLETE C AND DELUXE D BOARD
SYSTEM TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-39
Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Retry Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Aquazone Deluxe D Control LED Indicators . . . . . 39
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39,40
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Water Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Condensate Drain Pans . . . . . . . . . . . . . . . . . . . . . . . . . 39
Refrigerant System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Condensate Drain Cleaning . . . . . . . . . . . . . . . . . . . . . 39
Air Coil Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Condenser Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Checking System Charge . . . . . . . . . . . . . . . . . . . . . . . 40
Refrigerant Charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Air Coil Fan Motor Removal . . . . . . . . . . . . . . . . . . . . . 40
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 40-43
Thermistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Control Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
50VQP START-UP CHECKLIST . . . . . . . . . . . CL-1,CL-2
IMPORTANT: Read the entire instruction manual before
starting installation.
SAFETY CONSIDERATIONS
Installation and servicing of air-conditioning equipment can
be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should
install, repair, or service air-conditioning equipment.
Untrained personnel can perform basic maintenance functions of cleaning coils and filters and replacing filters. All other
operations should be performed by trained service personnel.
When working on air-conditioning equipment, observe precautions in the literature, tags and labels attached to the unit, and
other safety precautions that may apply.
Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock or
other conditions which may cause personal injury or property
damage. Consult a qualified installer, service agency, or your
distributor or branch for information or assistance. The
qualified installer or agency must use factory-authorized kits or
accessories when modifying this product. Refer to the individual instructions packaged with the kits or accessories when
installing.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53500080-01
Printed in U.S.A.
Form 50VQP-C1SI
Pg 1
11-10
Replaces: New
Follow all safety codes. Wear safety glasses and work
gloves. Use quenching cloth for brazing operations. Have fire
extinguisher available. Read these instructions thoroughly and
follow all warnings or cautions attached to the unit. Consult
local building codes and the National Electrical Code (NEC,
U.S.A.) for special installation requirements.
Understand the signal words — DANGER, WARNING,
and CAUTION. DANGER identifies the most serious hazards
which will result in severe personal injury or death. WARNING signifies hazards that could result in personal injury or
death. CAUTION is used to identify unsafe practices, which
would result in minor personal injury or product and property
damage.
Recognize safety information. This is the safety-alert
symbol ( ). When you see this symbol on the unit and in
instructions or manuals, be alert to the potential for personal
injury.
Step 2 — Check Unit — Upon receipt of shipment at
the jobsite, carefully check the shipment against the bill of
lading. Make sure all units have been received. Inspect the carton or crating of each unit, and inspect each unit for damage.
Ensure the shipping company makes proper notation of any
shortages or damage on all copies of the freight bill. Concealed
damage not discovered during unloading must be reported to
the shipping company within 15 days of receipt of shipment.
NOTE: It is the responsibility of the purchaser to file all
necessary claims with the shipping company.
1. Verify unit is correct model for entering water temperature of job.
2. Be sure that the location chosen for unit installation provides ambient temperatures maintained above freezing.
Well water applications are especially susceptible to
freezing.
3. Be sure the installation location is isolated from sleeping
areas, private offices and other acoustically sensitive
spaces.
NOTE: A sound control accessory package may be used
to help eliminate sound in sensitive spaces.
4. Check local codes to be sure a secondary drain pan is not
required under the unit.
5. Be sure unit is mounted at a height sufficient to provide
an adequate slope of the condensate lines. If an appropriate slope cannot be achieved, a field-supplied condensate
pump may be required.
6. Provide sufficient space for duct connection.
7. Provide adequate clearance for filter replacement and
drain pan cleaning. Do not allow piping, conduit, etc. to
block filter access.
8. Provide sufficient access to allow maintenance and
servicing of the fan and fan motor, compressor and coils.
Removal of the entire unit from the closet should not be
necessary.
9. Provide an unobstructed path to the unit within the closet
or mechanical room. Space should be sufficient to allow
removal of unit if necessary.
10. Provide ready access to water valves and fittings, and
screwdriver access to unit side panels, discharge collar,
and all electrical connections.
11. Where access to side panels is limited, pre-removal of the
control box side mounting screws may be necessary for
future servicing.
STORAGE — If the equipment is not needed for immediate
installation upon its arrival at the jobsite, it should be left in its
shipping carton and stored in a clean, dry area of the building
or in a warehouse. Units must be stored in an upright position
at all times. If carton stacking is necessary, stack units a maximum of 3 high. Do not remove any equipment from its shipping package until it is needed for installation.
WARNING
Electrical shock can cause personal injury or death. Before
installing or servicing system, always turn off main power
to system. There may be more than one disconnect switch.
Turn off accessory heater power if applicable.
GENERAL
This Installation and Start-Up Instructions literature is for
Aquazone™ water source heat pump systems.
Water source heat pumps (WSHPs) are single-package vertically mounted units with electronic controls designed for
year-round cooling and heating.
IMPORTANT: The installation of water source heat pump
units and all associated components, parts, and accessories
which make up the installation shall be in accordance with
the regulations of ALL authorities having jurisdiction and
MUST conform to all applicable codes. It is the responsibility of the installing contractor to determine and comply
with ALL applicable codes and regulations.
INSTALLATION
Step 1 — Check Jobsite — Installation, operation and
maintenance instructions are provided with each unit. Before
unit start-up, read all manuals and become familiar with the
unit and its operation. Thoroughly check out the system before
operation. Complete the inspections and instructions listed
below to prepare a unit for installation. See Table 1 for unit
physical data.
Vertical units are designed for indoor installation only and
are typically installed in a floor-level closet or a small mechanical room. Refer to Fig. 1 for an example of a typical vertical
installation. See Fig. 2 and 3 for overall unit dimensions.
CAUTION
To avoid equipment damage, do not use these units as a
source of heating or cooling during the construction
process. The mechanical components and filters used in
these units quickly becomes clogged with construction
dirt and debris which may cause system damage.
2
Table 1 — 50VQP Unit Physical Data
UNIT 50VQP
COMPRESSOR QUANTITY
Factory Charge HFC-410A (kg) per circuit
BLOWER MOTOR
Blower Motor Quantity
Standard Motor (kW)
Large Motor (kW)
BLOWER
No. of Blowers
084
150
168
3.97
096
120
Scroll (1)
4.42
6.35
3.97
192
240
Scroll (2)
4.42
6.35
7.03
.75
1.12
1.12
1.49
2.24
3.73
300
7.03
1.49
2.24
2.24
3.73
3.73
5.60
1
Blower Wheel Size D x W (cm)
1.49
2.24
1
3.73
5.60
2
38.1 x
38.1
38.1 x 27.9
38.1 x
38.1
38.1 x 27.9
WATER CONNECTION SIZE
FPT (in.) [mm]
1-1/2 [38.1]
COAX VOLUME
Volume (liters)
CONDENSATE CONNECTION SIZE
FPT (in.) [mm]
AIR COIL DATA
Air Coil Dimensions H x W (cm)
Air Coil Total Face Area (sq m)
Air Coil Tube Size (cm)
Air Coil Fin Spacing (fins per cm)
Air Coil Number of Rows
MISCELLANEOUS DATA
Filter Standard Throwaway (qty) (cm)
Weight - Operating (kg)
Weight - Packaged (kg)
8.28
2-1/2
[63.5]
2 [50.8]
9.37
13.11
18.29
24.08
27.98
1 [25.4]
91.4 x 121.9
1.11
91.4 x 121.9
2.22
3/8 [0.953]
4.72
4
5.5
2
3
(4) 45.74 x 63.5 x 2.5
399
422
406
429
LEGEND
FPT — Female Pipe Thread
NOTES:
1. All units have grommet and spring compressor mountings, and
2.2 cm and 3.5 cm electrical knockouts.
435
442
5.5
2
4.72
4
3
(8) 45.74 x 63.5 x 2.5
725
755
739
769
2. Use the lowest maximum pressure rating when multiple options
are combined:
OPTION
Base Unit
Motorized Water Valve
Internal Secondary Pump
MAXIMUM PRESSURE (kPa)
3100
2750
999
Supply Air
Optional Discharge
Optional Discharge
Supply Air
Supply Water
Return
Water
24 V Remote
Mtd. Stat
T
Balancing
Valve
Condensate
Water In
Water Out
Unions
Valves
769
782
Access
Panel
Access
Panel
Access
Panel
Access
Panel
Power
Supply
Control Box
Trap
Vibration
Pad
Condensate
Fig. 1 — Typical 50VQP Unit Installation
3
Disconnect
Switch or
Per Local Codes
ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW
19.3
F
D
B
19.3
F
NRP
AIR OUT
a50-8436
AIR OUT
NRP
BSP
T
BSP
NRP
RETURN AIR
RETURN AIR
S
C
4
1
Q
4
NRP
3
Control Box
CAP+MSP
02
NRP
2
5
U
R
Control Box
4
3
3
P
N
01
4
2
NRP
MK
A
L
M
K
CSP+CAP+MSP
L
CSP
3
5
1
NOTE 5
REAR RETURN TOP DISCHARGE
FRONT RETURN TOP DISCHARGE
4.3
F
D
RETURN AIR
F
BSP
E
BSP
BSP
AIR OUT
AIR OUT
NRP
4
1
5
NRP
RETURN AIR
NRP
3
4
NRP
4
2
CAP+MSP
5
Control Box
4
4
3
4
2
Control Box
5
3
4
4
CSP
3
5
1
NRP
CSP+CAP+MSP
SIDE
SERVICE ACCESS
(SEE NOTE)
SERVICE ACCESS
91 CM
FRONT AND BACK
BSP
CAP
CSP
MSP
NRP
—
—
—
—
—
REAR RETURN FRONT DISCHARGE
FRONT RETURN REAR DISCHARGE
LEGEND
Blower Service Panel
Control Access Panel
Compressor Service Panel
Motor Service Panel
Non-Removable Panel
CONNECTIONS
NOTES:
1. All dimensions in centimeters.
2. Units require 0.9 m clearance for water connections, CAP, CSP, MSP, and BSP service access.
3. Overall cabinet height dimension does not include duct flange when in top discharge configuration.
4. Overall cabinet width dimension does not include filter rack and duct flange when on front or back discharge configuration.
5. Side service access must be 0.9 m on either side that connections are made. If no connections are made
on a side, then service access can be 15 mm minimum.
6. While access to all removable panels is not required, installer should take care to comply with all building
codes and allow adequate clearance for future field service.
7. Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT
plugs are shipped loose in a plastic bag tied to the water leg in front of the unit. Installer must plug water
inlet/outlet side not being connected to.
8. Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be
tied inside the unit. Installer must untie the drain hose and connect to the condensate drain hole of
installer’s choice.
9. Electrical access is available on either side (left or right) of unit and is also available (left or right) in the
front of the unit.
10. Overall depth — add 7.9 cm for 2.5 or 5 cm filter. Add 13 cm for 10 cm filter.
UNIT
50VQP
OVERALL
CABINET (cm)
DISCHARGE
CONNECTIONS (cm)
Duct Flange
D
E
Supply
Supply
F
Width
Depth
A
Depth
B
Width
C
Height
084-120
86.4
134.9
200.7
44.5
44.6
150
86.4
134.9
200.7
54.4
44.6
50VQP084-120
50VQP150
1
Water Inlet (See Note 7)
11/2 in. FPT
2 in. FPT
2
Water Outlet (See Note 7)
11/2 in. FPT
2 in. FPT
3
Condensate Drain (See Note 8)
1 in. FPT
1 in. FPT
4
High Voltage Access (See Note 9)
13/8 in.
13/8 in.
5
7/
Low Voltage Access (See Note 9)
WATER
CONNECTIONS (cm)
ELECTRICAL
KNOCKOUTS (cm)
8
7/
in.
8
in.
RETURN AIR
CONNECTIONS (cm)
(Using Return Air Opening)
S
T
Return Return
U
V
Depth
Height
K
1-Water
Inlet
L
1-Water
Outlet
M
3Condesate
N
O1
O2
P
Q
R
45.1
78.7
7.6
68.6
65.1
78.7
96.4
87.7
2.5
7.6
121.9
82.2
113.3
6.9
45.1
78.7
7.6
68.6
65.1
78.7
96.4
87.7
2.5
7.6
121.9
82.2
113.3
6.9
Fig. 2 — 50VQP084-150 Unit Dimensions
4
ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW
V
a50-8437
F
19.3
D
19.3
G
B
D
AIR OUT
AIR OUT
E
C
NRP
RETURN AIR
NRP
NRP
F
AIR OUT
AIR OUT
E
T
BSP
BSP
RETURN AIR
S
RETURN AIR
1
Q
S
5
3
MSP
02
2
4
RETURN AIR
BSP
U
R
P
01
3 Control Box
4
NRP
NRP
CAP
Control Box
4
CSP+CAP
2
1
3
CSP
5
4
N
CSP+MSP
M
CSP
L
3
L
M
NRP
NRP
K
K
A
NOTE 5
FRONT RETURN TOP DISCHARGE
REAR RETURN TOP DISCHARGE
4.3
BSP
F
D
G
E
NRP
D
RETURN
AIR
AIR OUT
NRP
4
1
NRP
AIR OUT
AIR OUT
AIR OUT
RETURN AIR
5
3
MSP
4
2
4
CAP
NRP
RETURN AIR
Control Box
5
2
4
5
4
CSP
NRP
3 Control Box
4
3
NRP
Service Access
3’ (91 cm)
Front and Back
(All Configurations)
5
4
FRONT RETURN REAR DISCHARGE
LEGEND
Blower Service Panel
Control Access Panel
Compressor Service Panel
Motor Service Panel
Non-Removable Panel
OVERALL
CABINET (cm)
CONNECTIONS
DISCHARGE
CONNECTIONS (cm)
Duct Flange
D
E
Supply
Supply
F
Width
Depth
A
Depth
B
Width
C
Height
168-240
86.4
270.9
200.7
44.5
44.6
300
86.4
270.9
200.7
54.4
44.6
3
CSP+MSP
Side Service Access
(See Note)
NOTES:
1. All dimensions in centimeters.
2. Units require 91 cm clearance for water connections, CAP, CSP, MSP, and BSP service access.
3. Overall cabinet height dimension does not include duct flange when in top discharge configuration.
4. Overall cabinet width dimension does not include filter rack and duct flange when on front or back discharge configuration.
5. Side service access must be 91 cm on either side that connections are made. If no connections are made
on a side, then service access can be 15 mm minimum.
6. While access to all removable panels is not required, installer should take care to comply with all building
codes and allow adequate clearance for future field service.
7. Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT
plugs are shipped loose in a plastic bag tied to the water leg in front of the unit. Installer must plug water
inlet/outlet side not being connected to.
8. Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be
tied inside the unit. Installer must untie the drain hose and connect to the condensate drain hole of
installer’s choice.
9. Electrical access is available on either side (left or right) of unit and is also available (left or right) in the
front of the unit.
10. Overall depth — add 7.9 cm for 2.5 or 5 cm filter. Add 13 cm for 10 cm filter.
UNIT
50VQP
1
NRP
REAR RETURN FRONT DISCHARGE
—
—
—
—
—
4
CSP+CAP
CSP
BSP
CAP
CSP
MSP
NRP
F
BSP
RETURN
AIR
50VQP168-240
50VQP300
1
Water Inlet (See Note 7)
2 in. FPT
21/2 in. FPT
2
Water Outlet (See Note 7)
2 in. FPT
21/2 in. FPT
3
Condensate Drain (See Note 8)
1 in. FPT
1 in. FPT
4
High Voltage Access (See Note 9)
13/8 in.
13/8 in.
5
Low Voltage Access (See Note 9)
WATER
CONNECTIONS (cm)
7/
ELECTRICAL
KNOCKOUTS (cm)
8
7/
8
in.
in.
RETURN AIR
CONNECTIONS (cm)
(Using Return Air Opening)
S
T
Return Return
U
V
Depth Height
G
K
1-Water
Inlet
L
2-Water
Outlet
M
3Condensate
N
O1
O2
P
Q
R
45.1
79.4
78.7
7.6
68.6
65.1
78.1
96.4
87.8
2.5
7.6
121.9
82.2
113.3
6.9
45.1
59.4
78.7
7.6
68.6
65.1
78.1
96.4
87.8
2.5
7.6
121.9
82.2
113.3
6.9
Fig. 3 — 50VQP168-300 Unit Dimensions
5
• ALLOW enough space for service personnel to perform
maintenance.
• Provisions must be made for return air to freely enter the
space if unit needs to be installed in a confined area such
as a closet.
PROTECTION — Once the units are properly positioned on
the jobsite, they must be covered with either a shipping carton,
vinyl film, or an equivalent protective covering. Open ends of
pipes stored on the jobsite must be capped. This precaution is
especially important in areas where painting, plastering, or
spraying of fireproof material, etc. is not yet complete. Foreign
material that is allowed to accumulate within the units can prevent proper start-up and necessitate costly clean-up operations.
Before installing any of the system components, be sure to
examine each pipe, fitting, and valve, and remove any dirt or
foreign material found in or on these components.
Step 4 — Mount the Unit — Vertical units are available in rear or front return air configurations.
DISCHARGE CONFIGURATION CONVERSION — To
change the discharge configuration of the unit from top discharge to straight (right or left) discharge, follow the procedure
below. To change the discharge configuration of the unit from
straight (right or left) discharge to top discharge, reverse the
procedure below.
1. Remove the 3 panels as shown in Fig. 4.
CAUTION
DO NOT store or install units in corrosive environments or
in locations subject to temperature or humidity extremes
(e.g., attics, garages, rooftops, etc.). Corrosive conditions
and high temperature or humidity can significantly reduce
performance, reliability, and service life. Always move
units in an upright position. Tilting units on their sides may
cause equipment damage.
BLOWER ACCESS
PANEL
INSPECT UNIT — To prepare the unit for installation, complete the procedures listed below:
1. Compare the electrical data on the unit nameplate with
ordering and shipping information to verify that the
correct unit has been shipped.
2. Do not remove the packaging until the unit is ready for
installation.
3. Verify that the unit’s refrigerant tubing is free of kinks or
dents, and that it does not touch other unit components.
4. Inspect all electrical connections. Be sure connections are
clean and tight at their terminations.
5. Loosen compressor bolts until the compressor rides freely
on springs. Remove shipping restraints.
6. Remove the four 1/4 in. (6 mm) shipping bolts from compressor support plate (two bolts on each side) to maximize vibration and sound alternation.
C-BOX/
MOTOR ACCESS
PANEL
COMPRESSOR
ACCESS PANEL
a50-8466
Fig. 4 — Remove Panels
2. Remove blockoff air handler. Loosen belt and remove.
See. Fig. 5.
a50-8467
BLOCKOFF
AIR HANDLER
CAUTION
Failure to remove shipping brackets from spring-mounted
compressors will cause excessive noise and could cause
component failure due to added vibration.
7. Remove any blower support cardboard from inlet of the
blower.
8. Locate and verify any accessory kit located in compressor
and/or blower section.
9. Remove any access panel screws that may be difficult to
remove once unit is installed.
Fig. 5 — Remove Blockoff Air Handler and Belt
3. Remove 4 bolts from blower panel. Remove 4 bolts (2
bolts on each side) from blower sides. See Fig. 6.
Step 3 — Locate Unit — The following guidelines
should be considered when choosing a location for a WSHP:
• Units are for indoor use only.
• Locate in areas where ambient temperatures are between
4.4 C and 37.8 C and relative humidity is no greater than
75%.
• Provide sufficient space for water, electrical and duct
connections.
NOTE: Water inlets/outlets and high/low voltage electrical
access are available on either side of the unit. Electrical access is also available on the unit front. See Fig. 2 and 3.
• Locate unit in an area that allows for easy access and
removal of filter and access panels.
NOTE: Unit has full filter frame bottom access for 25, 51,
or 102 mm filters.
STEP 3
a50-8468
STEP 3
Fig. 6 — Remove Bolts from
Blower Panel and Sides
6
4. Remove 4 bolts and take blower glides out. See Fig. 7.
a50-8469
8. When the blower assembly is parallel to the floor, push
the blower assembly back so the blower panel is flush
with the unit. See. Fig. 11.
a50-8473
BLOWER GLIDES
(2X)
Fig. 11 — Push in Blower Assembly
Fig. 7 — Remove Bolts and Blower Glides
9. Attach blower assembly with 4 bolts as shown in Fig. 12.
5. Attach blower glides to blower bottom load brackets as
shown in Fig. 8. Use bottom set of holes on blower bottom load brackets. The blower shaft should be sitting directly on top of the blower glides.
a50-8474
a50-8470
Fig. 12 — Attach Blower Asembly
Fig. 8 — Attach Blower Glides
10. Remove the 2 blower glides and reattach back into compressor section. See Fig. 13.
6. Stand in front and pull the blower assembly on to the
ridge of the blower glides. See Fig. 9.
a50-8471
STEP 10
Fig. 9 — Pull Blower Assembly to Glides
a50-8475
7. Rotate blower assembly using the blower glides as a
guiding track. See Fig. 10.
a50-8472
Fig. 13 — Remove Blower Glides and Reattach
11. Use four 1/4 in. (6 mm) 20 UNC bolts (2 bolts on each
side) to bolt blower assembly to blower bottom load
brackets. Reattach belt and tighten. See Fig. 14.
Fig. 10 — Rotate Blower Assembly
7
1. Mount the unit so that the return-air inlet is 90 degrees to
the return-air grille. Install a sound baffle to reduce lineof-sight sound transmitted through return-air grilles.
2. Mount the unit on a rubber or neoprene pad to minimize
vibration transmission to the building structure. Extend
the pad beyond all four edges of the unit.
a50-8476
NOTE: Some codes require the use of a secondary drain pan
under vertical units. Check local codes for more information.
CONTROL BOX/MOTOR ACCESS CONFIGURATION
CONVERSION — To change the configuration of the control
box/motor access from the front of the unit to the back of the
unit, follow the procedure below. To change the configuration
of the control box/motor access from the back of the unit to the
front of the unit, reverse the procedure below.
1. Remove the 3 panels as shown in Fig. 17.
a50-8479
Fig. 14 — Bolt Blower Assembly to Load Brackets
BACK COMPRESSOR/
C-BOX/ MOTOR ACCESS
PANEL
RETURN
AIR
FRONT C-BOX/
MOTOR ACCESS
PANEL
12. Reattach blockoff air handler as shown in Fig. 15.
COMPRESSOR
ACCESS PANEL
CONTROL
BOX
BLOCKOFF
AIR HANDLER
Fig. 17 — Remove Access Panels
2. Remove motor cover and control box cover as shown in
Fig. 18.
a50-8480
a50-8477
MOTOR
COVER
Fig. 15 — Reattach Blockoff Air Handler
13. Put 3 panels back onto unit. See Fig. 16.
BLOWER FILLER
PANEL
CONTROL BOX COVER
Fig. 18 — Remove Motor and Control Box Covers
a50-8478
3. Remove 4 screws from control box. Using the guide rails
as a guide, flip the control box down, slide the box across,
and then flip the box up as shown in Fig. 19. Reattach the
control box with screws.
C-BOX/MOTOR ACCESS
PANEL
a50-8481
COMPRESSOR
PANEL ACCESS
C
A
SCREWS
Fig. 16 — Replace Panels
B
Sound minimization is achieved by enclosing the unit within a small mechanical room or a closet. The following are additional measures for sound control.
RIGHT SIDE VIEW
Fig. 19 — Flip Control Box
8
8. Put 3 panels back onto unit. See Fig. 23.
4. Loosen belt tension and take belt off. See Fig. 20.
5. Remove bolt-belt adjustment assembly. See Fig. 20.
a50-8482
STEP 5
CONTROL
BOX
STEP 4
a50-8485
BOLT-BELT ADJUSTMENT ASM
FRONT RETURN TOP DISCHARGE
Fig. 20 — Remove Belt and Bolt-Belt Adjustment
Assembly
Fig. 23 — Replace Access Panels
6. Move bolt-belt adjustment assembly to opposite side and
reattach. See Fig. 21.
a50-8483
Step 5 — Check Duct System — The duct system
should be sized to handle the design airflow quietly.
NOTE: Depending on the unit, the fan wheel may have a shipping support installed at the factory. This must be removed
before operating unit.
SOUND ATTENUATION — To eliminate the transfer of
vibration to the duct system, a flexible connector is recommended for both discharge and return air duct connections on
metal duct systems. The supply and return plenums should include internal duct liner of fiberglass or be made of duct board
construction to maximize sound attenuation of the blower.
Installing the WSHP unit to uninsulated ductwork in an unconditioned space is not recommended since it will sweat and
adversely affect the unit’s performance.
STEP 6
To reduce air noise, at least one 90-degree elbow could be
included in the supply and return air ducts, provided system
performance is not adversely impacted. The blower speed can
be also changed in the field to reduce air noise or excessive airflow, provided system performance is not adversely impacted.
EXISTING DUCT SYSTEM — If the unit is connected to
existing ductwork, consider the following:
• Verify that the existing ducts have the proper capacity to
handle the unit airflow. If the ductwork is too small,
larger ductwork should be installed.
• Check existing ductwork for leaks and repair as
necessary.
NOTE: Local codes may require ventilation air to enter the
space for proper indoor air quality. Hard-duct ventilation may
be required for the ventilating air supply. If hard ducted ventilation is not required, be sure that a proper air path is provided
for ventilation air to unit to meet ventilation requirement of the
space.
Fig. 21 — Move Bolt-Belt Adjustment Assembly
7. Put belt back on and tighten. Put control box cover and
motor cover on return side. See Fig. 22.
a50-8484
CONTROL BOX
COVER
MOTOR
COVER
Step 6 — Install Condensate Drain — The condensate drain can be connected to either side of the unit. The
50VQP units come with a flex hose and 1 in. (25 m) FPT condensate connection tied inside. To install the condensate drain
(see Fig. 24.):
1. Untie the flex hose and make interal trap on either the left
side or right side of the unit.
2. Internally attach mounting plate with FPT fitting.
Fig. 22 — Replace Belt and Motor and
Control Box Covers
9
• If condensate pump is present on unit, be sure drain connections have a check valve to prevent back flow of condensate into other units.
a50-8486
Step 7 — Pipe Connections — Depending on the
application, there are 3 types of WSHP piping systems to choose
from: water loop, ground-water and ground loop. Refer to the
Carrier System Design Manual for additional information.
All WSHP units utilize low temperature soldered female
pipe thread fittings for water connections to prevent annealing
and out-of-round leak problems which are typically associated
with high temperature brazed connections. Refer to Table 1 for
connection sizes. When making piping connections, consider
the following:
• A backup wrench must be used when making screw connections to unit to prevent internal damage to piping.
• Insulation may be required on piping to avoid condensation in the case where fluid in loop piping operates at
temperatures below dew point of adjacent air.
• Piping systems that contain steel pipes or fittings may
be subject to galvanic corrosion. Dielectric fittings may
be used to isolate the steel parts of the system to avoid
galvanic corrosion.
WATER LOOP APPLICATIONS — Water loop applications
usually include a number of units plumbed to a common piping system. Maintenance to any of these units can introduce air
into the piping system. Therefore, air elimination equipment
comprises a major portion of the mechanical room plumbing.
The flow rate is usually set between 2.41 and 3.23 L/m per
kW of cooling capacity. For proper maintenance and servicing,
pressure-temperature (P/T) ports are necessary for temperature
and flow verification.
In addition to complying with any applicable codes, consider the following for system piping:
• Piping systems utilizing water temperatures below
10.0 C require 13 mm closed cell insulation on all piping
surfaces to eliminate condensation.
• All plastic to metal threaded fittings should be avoided
due to the potential to leak. Use a flange fitted substitute.
• Teflon tape thread sealant is recommended to minimize
internal fouling of the heat exchanger.
• Use backup wrench. Do not overtighten connections.
• Route piping to avoid service access areas to unit.
• The piping system should be flushed prior to operation to
remove dirt and foreign materials from the system.
GROUND-LOOP APPLICATIONS — Temperatures between –3.9 and 43.3 C and a cooling capacity of 2.41 to
3.23 L/s per kW are recommended. In addition to complying with any applicable codes, consider the following for
system piping:
• Piping materials should be limited to only polyethylene
fusion in the buried sections of the loop.
• Galvanized or steel fittings should not be used at any
time due to corrosion.
• All plastic to metal threaded fittings should be avoided
due to the potential to leak. Use a flange fitted substitute.
• Do not overtighten connections.
• Route piping to avoid service access areas to unit.
• Pressure-temperature (P/T) plugs should be used to measure flow of pressure drop.
GROUND-WATER APPLICATIONS — Typical groundwater piping is shown in Fig. 26. In addition to complying
with any applicable codes, consider the following for system piping:
• Install shut-off valves for servicing.
• Install pressure-temperature plugs to measure flow and
temperature.
Fig. 24 — Install Condensate Drain
Each unit must be installed with its own individual trap,
vent and means to flush or blow out the condensate drain line.
Do not install units with a common trap or vent. See Fig. 25.
Vent
*3/4" IPT
Trap Depth
1.5" [38mm]
3/4" PVC or
Copper by others
Min 1.5"
[38mm]
1/4" per foot
(21mm per m)
drain slope
NOTE: Trap should be deep enough to offset maximum unit static
difference.
Fig. 25 — Trap Condensate Drain
Consider the following:
• Units are typically installed directly above each other on
successive floors with condensate drains located near the
units.
• Connect the unit condensate drain connection to the
building condensate drain with a 1-in. (25 mm) drain
line.
• The horizontal run of a condensate hose is usually too
short to cause drainage problems, however the horizontal
run pitch of the condensate line should be at least 1 cm
for every 50 cm of run in the direction of flow. Avoid low
points and unpitched piping since dirt collects in low or
level areas and may cause stoppage and overflow.
• Install a condensate trap at each unit with the top of
the trap positioned below the unit condensate drain
connection.
• Design the length of the trap (water-seal) based upon the
amount of positive or negative pressure on the drain pan.
As a rule, 25 mm of trap is required for each 10 Pa of
negative pressure on the unit.
VENTING — A vent should be installed in the condensate
line of any application which may allow dirt or air to collect in
the line. Consider the following:
• Always install a vent where an application requires a
long horizontal run.
• Always install a vent where large units are working
against higher external static pressure and to allow
proper drainage for multiple units connected to the same
condensate main.
• Be sure to support the line where anticipated sagging
from the condensate or when “double trapping” may
occur.
10
POWER CONNECTION — Line voltage connection is
made by connecting the incoming line voltage wires to the
L side of the CC terminal. See Tables 3 and 4 for correct
wire and maximum overcurrent protection sizing.
SUPPLY VOLTAGE — Operating voltage to unit must be
within voltage range indicated on unit nameplate.
On 3-phase units, voltages under load between phases must
be balanced within 2%. Use the following formula to determine the percentage voltage imbalance:
% Voltage Imbalance
• Boiler drains and other valves should be connected using
a “T” connector to allow acid flushing for the heat
exchanger.
• Do not overtighten connections.
• Route piping to avoid service access areas to unit.
• Use PVC SCH80 or copper piping material.
NOTE: PVC SCH40 should not be used due to system high
pressure and temperature extremes.
Water Supply and Quantity — Check water supply. Water
supply should be plentiful and of good quality. See Table 2 for
water quality guidelines.
= 100 x
IMPORTANT: Failure to comply with the above required
water quality and quantity limitations and the closedsystem application design requirements may cause damage
to the tube-in-tube heat exchanger that is not the responsibility of the manufacturer.
max voltage deviation from average voltage
average voltage
Example: Supply voltage is 420-3-50.
AB = 425 volts
BC = 422 volts
AC = 417 volts
In all applications, the quality of the water circulated
through the heat exchanger must fall within the ranges listed in
the Water Quality Guidelines table. Consult a local water treatment firm, independent testing facility, or local water authority
for specific recommendations to maintain water quality within
the published limits.
Average Voltage =
=
Step 8 — Field Power Supply Wiring
425 + 422 + 417
3
1264
3
= 421
Determine maximum deviation from average voltage:
(AB) 425 – 421 = 4 v
(BC) 422 – 421 = 1 v
(AC) 421 – 418 = 3 v
Maximum deviation is 4 v.
Determine percent voltage imbalance.
WARNING
To avoid possible injury or death due to electrical shock,
open the power supply disconnect switch and secure it in
an open position during installation.
CAUTION
% Voltage Imbalance = 100 x
Use only copper conductors for field-installed electrical
wiring. Unit terminals are not designed to accept other
types of conductors.
4
421
= 0.95%
This amount of phase imbalance is satisfactory as it is
below the maximum allowable 2%.
Operation on improper line voltage or excessive phase
imbalance constitutes abuse and may cause damage to electrical components.
NOTE: If more than 2% voltage imbalance is present, contact
local electric utility.
420-VOLT OPERATION — All 380/420 volt units are factory
wired for 380 volts. The transformers may be switched to
420-volt operation (as illustrated on the wiring diagram) by
disconnecting the VIO lead at L1 and attaching the BRN lead
to L1. Close open end of VIO lead.
All field-installed wiring, including the electrical ground,
MUST comply with the National Electrical Code (NEC) as
well as applicable local codes. In addition, all field wiring must
conform to the Class II temperature limitations described in the
NEC.
Refer to unit wiring diagrams Fig. 27-30 for a schematic of
the field connections which must be made by the installing (or
electrical) contractor. See Tables 3 and 4 for fuses sizes.
Consult the unit wiring diagram located on the inside of the
compressor access panel to ensure proper electrical hookup.
The installing (or electrical) contractor must make the field
connections when using field-supplied disconnect.
Operating voltage must be the same voltage and phase as
shown in electrical data shown in Tables 3 and 4.
Make all final electrical connections with a length of flexible conduit to minimize vibration and sound transmission to
the building.
11
Table 2 — Water Quality Guidelines
HX
CLOSED RECIRCULATING†
OPEN LOOP AND RECIRCULATING WELL**
MATERIAL*
Scaling Potential — Primary Measurement
Above the given limits, scaling is likely to occur. Scaling indexes should be calculated using the limits below.
pH/Calcium Hardness Method
All
N/A
pH < 7.5 and Ca Hardness, <100 ppm
Index Limits for Probable Scaling Situations (Operation outside these limits is not recommended.)
Scaling indexes should be calculated at 150 F for direct use and HWG applications, and at 90 F for indirect HX use. A monitoring plan should be implemented.
Ryznar Stability Index
6.0 - 7.5
All
N/A
If >7.5 minimize steel pipe use.
Langelier Saturation Index
–0.5 to +0.5
All
N/A
If <–0.5 minimize steel pipe use.
Based upon 150 F HWG and direct well, 85 F indirect well HX.
Iron Fouling
Iron Fe2+ (Ferrous)
<0.2 ppm (Ferrous)
All
N/A
(Bacterial Iron Potential)
If Fe2+ (ferrous) >0.2 ppm with pH 6 - 8, O2<5 ppm check for iron bacteria.
Iron Fouling
<0.5 ppm of Oxygen
All
N/A
Above this level deposition will occur.
Corrosion Prevention††
pH
6 - 8.5
6 - 8.5
All
Monitor/treat as needed.
Minimize steel pipe below 7 and no open tanks with pH <8.
Hydrogen Sulfide (H2S)
<0.5 ppm
At H2S>0.2 ppm, avoid use of copper and cupronickel piping or HXs.
All
N/A
Rotten egg smell appears at 0.5 ppm level.
Copper alloy (bronze or brass) cast components are okay to <0.5 ppm.
Ammonia Ion as Hydroxide,
<0.5 ppm
Chloride, Nitrate and Sulfate
All
N/A
Compounds
Maximum Chloride Levels
Maximum allowable at maximum water temperature.
50 F (10 C)
75 F (24 C)
100 F (38 C)
Copper
N/A
<20 ppm
NR
NR
Cupronickel
N/A
<150 ppm
NR
NR
304 SS
N/A
<400 ppm
<250 ppm
<150 ppm
316 SS
N/A
<1000 ppm
<550 ppm
<375 ppm
Titanium
N/A
>1000 ppm
>550 ppm
>375 ppm
Erosion and Clogging
Particulate Size and Erosion
<10 ppm of particles and a
ppm (<1 ppm “sandfree” for reinjection) of particles and a maximum velocity of
maximum velocity of 6 fps. <10
All
6 fps. Filtered for maximum 800 micron size. Any particulate that is not removed can
Filtered for maximum
potentially
clog components.
800 micron size.
Brackish
Use cupronickel heat exchanger when concentrations of calcium or sodium chloride
All
N/A
are greater than 125 ppm are present. (Seawater is approximately 25,000 ppm.)
CONDITION
HWG
HX
N/A
NR
SS
—
—
—
—
—
LEGEND
Hot Water Generator
Heat Exchanger
Design Limits Not Applicable Considering Recirculating Potable Water
Application Not Recommended
Stainless Steel
††If the concentration of these corrosives exceeds the maximum allowable level,
then the potential for serious corrosion problems exists.
Sulfides in the water quickly oxidize when exposed to air, requiring that no agitation occur as the sample is taken. Unless tested immediately at the site, the
sample will require stabilization with a few drops of one Molar zinc acetate
solution, allowing accurate sulfide determination up to 24 hours after sampling. A low pH and high alkalinity cause system problems, even when both
values are within ranges shown. The term pH refers to the acidity, basicity, or
neutrality of the water supply. Below 7.0, the water is considered to be acidic.
Above 7.0, water is considered to be basic. Neutral water contains a pH of 7.0.
NOTE: To convert ppm to grains per gallon, divide by 17. Hardness in mg/l is
equivalent to ppm.
*Heat exchanger materials considered are copper, cupronickel, 304 SS (stainless steel), 316 SS, titanium.
†Closed recirculating system is identified by a closed pressurized piping system.
**Recirculating open wells should observe the open recirculating design
considerations.
Water
Control
Valve
Automatic
Balance Valve
Expansion
Tank
Water Out
Water In
From Pump
Shut-Off
Valve
Boiler
Drains
Strainer – Field-Installed Accessory
(16 to 20 mesh recommended for
filter sediment)
PressureTemperature
Plugs
Fig. 26 — Typical Ground-Water Piping Installation
12
13
AL
BC
CB
CC
CO
DPP
DS
FP1
FP2
HP
HPWS
JW3
LOC
MV
PDB1
PDB2
RVS
TRANS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Alarm Relay
Blower Contactor
Circuit Breaker
Compressor Contactor
Sensor, Condensate Overflow
Dual Point Power
Disconnect Switch
Sensor, Water Coil Freeze Protection
Sensor, Air Coil Freeze Protection
High-Pressure Switch
High-Pressure Water Switch
Clippable Field Selection Jumper
Loss of Charge Pressure Switch
Motorized Valve
Power Distribution Block
Power Distribution Block Dual Point Option
Reversing Valve Solenoid
Transformer
Factory Line Voltage Wiring
Factory Low Voltage Wiring
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
LEGEND
Complete C
Fig. 27 — 50VQP084-168 Unit with Complete C Control (Typical)
Wire Nut
Switch - High Pressure
Switch - Low Pressure
Temperature Switch
Relay Contacts - N.C.
Relay Contacts - N.O.
Solenoid Coil
Ground
Circuit Breaker
Condensate Pan
Thermistor
Relay/Contactor Coil
a50-8438
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC (National Electrical Code, U.S.A.) and local codes.
3. 380/420-v transformers will be connected for 380-v operation. For 420-v operation, disconnect
VIO lead at L1, and attach BRN lead to L1. Close open end of VIO lead.
4. FPI jumper provides low temperature protection for WATER. When using ANTIFREEZE solutions, cut JW3 jumper.
5. Typical heat pump thermostat wiring shown. Refer to thermostat installation instructions for wiring to the unit. Thermostat wiring must be “Class 1” and voltage rating equal to or greater than
unit supply voltage.
6. 24-v alarm signal shown. For dry alarm contact, cut JW1 jumper and dry contact will be available between AL1 and AL2.
7. Transformer secondary ground via Complete C board standoffs and screws to control box.
(Ground available from top two standoffs as shown.)
8. For dual point power option, blower wires (3 qty) will go to PDB2 only.
AL
BC
CB
CC
CO
DPP
DS
FP1
FP2
HP
HPWS
JW3
LOC
MV
PDB
PDB2
RVS
TRANS
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Alarm Relay
Blower Contactor
Circuit Breaker
Compressor Contactor
Sensor, Condensate Overflow
Dual Point Power
Disconnect Switch
Sensor, Water Coil Freeze Protection
Sensor, Air Coil Freeze Protection
High-Pressure Switch
High-Pressure Water Switch
Clippable Field Selection Jumper
Loss of Charge Pressure Switch
Motorized Valve
Power Distribution Block
Power Distribution Block Dual Point Option
Reversing Valve Solenoid
Transformer
Factory Line Voltage Wiring
Factory Low Voltage Wiring
Field Line Voltage Wiring
Field Low Voltage Wiring
Printed Circuit Trace
Optional Wiring
LEGEND
Fig. 28 — 50VQP084-168 with Deluxe D Control (Typical)
Wire Nut
Switch - High Pressure
Switch - Low Pressure
Temperature Switch
Relay Contacts - N.C.
Relay Contacts - N.O.
Solenoid Coil
Ground
Circuit Breaker
Condensate Pan
Thermistor
Relay/Contactor Coil
Deluxe D
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC (National Electrical Code) and local codes.
3. 380/420-v transformers will be connected for 380-v operation. For 420-v operation, disconnect VIO lead at L1, and attach BRN lead to L1. Close open end of VIO lead.
4. FP1 thermistor provides freeze protection for WATER. When using ANTIFREEZE solution, cut JW3 jumper.
5. Typical heat pump thermostat wiring shown. Refer to thermostat installation instructions
for wiring to the unit. Thermostat wiring must be “Class 1” and voltage rating equal to or
greater than unit supply voltage.
6. 24-v alarm signal shown. For dry alarm contact, cut AL2 DRY (JW4) jumper and dry contact will be available between AL1 and AL2.
7. Transformer secondary ground via Deluxe D board standoffs and screws to control box.
(Ground available from top two standoffs as shown.)
8. For dual point power option, blower wires (3 qty) will go to PDB2 only.
a50-8439
14
COMPLETE
C
CONTROL
PREMIER
LINK
PWR
Y
HS1/EXH/RVS
W
CR
CR
O
G
LEGEND
CR — Control Relay
LWT — Leaving Water Temperature Sensor
SAT — Supply Air Temperature Sensor
SPT — Space Temperature Sensor
NOTE: Reversing valve is on in Cooling
mode.
R
C
CMP1
FAN
AL2
PWR
J1
J8
AL1
A
J5
J6
CMPSAFE
S
P
T
J4
L
W
T
S
A
T
Fig. 29 — PremierLink™ Controller Applications with Complete C Control
PREMIER
LINK
PWR
DELUXE
D
CONTROL
Y1
HS2
Y2
HS1
LEGEND
LWT — Leaving Water Temperature Sensor
SAT — Supply Air Temperature Sensor
SPT — Space Temperature Sensor
NOTE: Reversing valve is on in Cooling
mode.
W1
O/W2
CMP2
G
CMP1
FAN
C
PWR
J1
J8
R
J5
J6
S
A
T
L
W
T
J4
CMPSAFE
S
P
T
AL1
Fig. 30 — PremierLink Controller Applications with Deluxe D Control
15
Table 3 — 50VQP Unit Electrical Data — Standard Unit
50VQP UNIT
SIZE
VOLTAGE
(V-Ph-Hz)
MIN/MAX
VOLTAGE
084
380/420-3-50
360/440
096
380/420-3-50
360/440
120
380/420-3-50
360/440
150
380/420-3-50
360/440
168
192
240
380/420-3-50
380/420-3-50
380/420-3-50
360/440
360/440
360/440
300
380/420-3-50
360/440
FLA
HACR
LRA
MCA
RLA
—
—
—
—
—
COMPRESSOR
BLOWER
OPTION
qty
RLA
LRA
A,B,C
E
A,B,C
A,B,C
E
A,B,C
E
A,B,C
A,B,C
A,B,C
A,B,C
E
1
1
1
1
1
1
1
2
2
2
2
2
11.2
11.2
12.2
16.7
16.7
18.6
18.6
11.2
12.2
16.7
18.6
18.6
75.0
75.0
101.0
111.0
111.0
118.0
118.0
75.0
101.0
111.0
118.0
118.0
LEGEND
Full Load Amps
Heating, Air Conditioning, and Refrigeration
Locked Rotor Amps
Minimum Circuit Amps
Rated Load Amps
FAN
MOTOR
FLA
1.8
2.5
2.5
3.6
4.9
4.9
7.8
3.4
4.9
7.8
7.8
12.2
TOTAL UNIT
FLA
MCA
MAX FUSE/
HACR
13.0
13.7
14.7
20.3
21.6
23.5
26.4
25.8
29.3
41.2
45.0
49.4
15.8
16.5
17.8
24.5
25.8
28.2
31.1
28.6
32.3
45.4
49.7
54.0
25
25
25
40
40
45
45
35
40
60
60
70
NOTES:
1. HACR circuit breaker in U.S.A. only.
2. All fuses Class RK-5.
Table 4 — 50VQP Unit Electrical Data — Dual Point Power Unit
50VQP
UNIT
SIZE
VOLTAGE
(V-Ph-Hz)
MIN/MAX
VOLTAGE
084
380/420-3-50
360/440
096
380/420-3-50
360/440
120
380/420-3-50
360/440
150
380/420-3-50
360/440
168
192
240
380/420-3-50
380/420-3-50
380/420-3-50
360/440
360/440
360/440
300
380/420-3-50
360/440
BLOWER
OPTION qty RLA LRA
A,B,C
E
A,B,C
A,B,C
E
A,B,C
E
A,B,C
A,B,C
A,B,C
A,B,C
E
1
1
1
1
1
1
1
2
2
2
2
2
11.2
11.2
12.2
16.7
16.7
18.6
18.6
11.2
12.2
16.7
18.6
18.6
75.0
75.0
101.0
111.0
111.0
118.0
118.0
75.0
101.0
111.0
118.0
118.0
COMPRESSOR
TOTAL
COMP
COMP FLA MCA
11.2
14.0
11.2
14.0
12.2
15.3
16.7
20.9
16.7
20.9
18.6
23.3
18.6
23.3
22.4
25.2
24.4
27.4
33.4
37.6
37.2
41.9
37.2
41.9
LEGEND
FLA — Full Load Amps
HACR — Heating, Air Conditioning, and Refrigeration
LRA — Locked Rotor Amps
MCA — Minimum Circuit Amps
RLA — Rated Load Amps
NOTES:
1. HACR circuit breaker in U.S.A. only.
2. All fuses Class RK-5.
16
COMP
MAX FUSE
25
25
25
35
35
40
40
35
35
50
60
60
EMERGENCY POWER SUPPLY
FAN MOTOR
FAN
FAN
FLA
MCA MAX FUSE
1.8
2.3
15
2.5
3.1
15
2.5
3.1
15
3.6
4.5
15
4.9
6.1
15
4.9
6.1
15
7.8
9.8
15
3.4
4.3
15
4.9
6.1
15
7.8
9.8
15
7.8
9.8
15
12.2
15.3
25
NOTE: The A terminal should only be used with 24 volt
signals — not line voltage signals.
WATER SOLENOID VALVES — An external solenoid
valve(s) should be used on ground water installations to shut
off flow to the unit when the compressor is not operating. A
slow closing valve may be required to help reduce water
hammer. Figure 33 shows typical wiring for a 24-vac external
solenoid valve. Figures 34 and 35 illustrate typical slow closing
water control valve wiring for Taco 500 Series and Taco ESP
Series valves. Slow closing valves take approximately 60 sec.
to open (very little water will flow before 45 sec.). Once fully
open, an end switch allows the compressor to be energized (only on valves with end switches). Only relay or triac based electronic thermostats should be used with slow closing valves.
When wired as shown, the slow closing valve will operate
properly with the following notations:
1. The valve will remain open during a unit lockout.
2. The valve will draw approximately 25 to 35 VA through
the “Y” signal of the thermostat.
Step 9 — Field Control Wiring
THERMOSTAT CONNECTIONS — The thermostat should
be wired directly to the Aquazone™ control board. See
Fig. 27-31.
COMPLETE C CONTROL
E
LIN
G
G
G
a50-8197
Y1
G
Y2
S1
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
SW9
OFF ON
G
O
CFM
G
TRANSFORMER
R
Y
J1
W
DEHUM
TB1
R
C
Y2 Y1 G O W C R DH AL1 A
A
AL1
THERMOSTAT CONNECTION
NOTE: Low voltage connector may be removed for
easy installation.
IMPORTANT: Connecting a water solenoid valve can
overheat the anticipators of electromechanical thermostats. Only use relay based electronic thermostats.
Fig. 31 — Low Voltage Field Wiring
C
WATER FREEZE PROTECTION — The Aquazone control
allows the field selection of source fluid freeze protection
points through jumpers. The factory setting of jumper JW3
(FP1) is set for water at –1.1 C. In earth loop applications,
jumper JW3 should be clipped to change the setting to –12.2 C
when using antifreeze in colder earth loop applications. See
Fig. 32.
Y1
CAPACITOR
D
LOA
COMPRESSOR CONTACTOR
a50-8441
2
3
1
AMV
TACO VALVE
Y1
C
HEATER SWITCH
THERMOSTAT
Fig. 34 — AMV Valve Wiring
a506268tf.tif
AQUAZONE CONTROL (Complete C Control Shown)
Fig. 32 — Typical Aquazone™ Control Board
Jumper Locations
a50-8442
AIR COIL FREEZE PROTECTION — The air coil freeze
protection jumper JW2 (FP2) is factory set for –1.1 C and
should not need adjusting.
ACCESSORY CONNECTIONS — Terminal labeled A on
the control is provided to control accessory devices such as
water valves, electronic air cleaners, humidifiers, etc. This
signal operates with the compressor terminal. See Fig. 33.
Refer to the specific unit wiring schematic for details.
Fig. 35 — Taco SBV Valve Wiring
PRE-START-UP
System Checkout — When the installation is complete,
follow the system checkout procedure outlined below before
starting up the system. Be sure:
1. Voltage is within the utilization range specifications of the
unit compressor and fan motor and voltage is balanced
for 3-phase units.
2. Fuses, breakers and wire are correct size.
3. Low voltage wiring is complete.
4. Piping and system flushing is complete.
5. Air is purged from closed loop system.
6. System is balanced as required. Monitor if necessary.
7. Isolation valves are open.
8. Water control valves or loop pumps are wired.
TERMINAL STRIP P2
C
24 VAC
TYPICAL
WATER
VALVE
A
Fig. 33 — Typical Aquazone Accessory Wiring
(Control D Shown)
17
cause premature belt failure and or intermittent airflow. An
overly tight belt can cause premature motor or blower bearing failure. To adjust the belt tension, follow the procedure
outlined below:
1. Remove belt from motor sheave.
2. Lift motor assembly.
3. Loosen the 5/16-in. hex nuts on the grommet motor adjustment bolts (2 per bolt). To increase the belt tension loosen
the top hex nut. To decrease the belt tension loosen the
bottom hex nut.
4. Turn the bolts by hand to the desired position then tighten
the 5/16-in. hex nuts (2 per bolt).
5. Lower the motor assembly.
6. Install the belt.
7. The belt tension can be adjusted by using one of the following methods:
a. Tighten until belt deflects approximately 13 mm
with very firm finger pressure.
b. Grasp belt midway between two pulleys and twist
for a 90-degreerotation.
NOTE: Adjusting less than 90 degrees will overtighten the belt and adjusting more than 90degrees
will loosen belt.
c. Set proper belt tension to 32 to 36 kg.
NOTE: The motor position should not need adjustment. Motor
sheave position is at mid position of each sheave. For example,
the motor sheave is 2.5 turns open on a 5-turn sheave. The belt
tension adjustment can also be accomplished by turning the
5/16-in. hex nuts to the desired position.
NOTE: Available airflows for all units are shown in
Tables 5-12.
9.
10.
11.
12.
13.
14.
15.
Condensate line is open and correctly pitched.
Transformer switched to lower voltage tap if necessary.
Blower rotates freely — shipping support is removed.
Blower speed is on correct setting.
Air filter is clean and in position.
Service/access panels are in place.
Return-air temperature is 4.4 to 26.7 C for heating and
10.0 to 43.3 C for cooling.
16. Air coil is clean.
17. Control field-selected settings are correct.
AIR COIL — To obtain maximum performance, the air coil
should be cleaned before starting the unit. A 10% solution of
dishwasher detergent and water is recommended for both sides
of the coil. Rinse thoroughly with water.
Airflow and External Static Pressure — The
50VQP units are available with standard, low, and high-static
factory-installed options. These options will substitute a different blower drive sheave for each static range. In addition, certain static ranges may require the optional large fan motor.
SHEAVE ADJUSTMENT — The 50VQP units are supplied
with a variable sheave drive on the fan motor to adjust for differing airflows at various ESP (external static pressure) conditions. See Tables 5-12 for unit airflows. When fully closed, the
sheave will produce the highest static capability (higher rpm).
To adjust sheave position, follow the procedure outlined below:
1. Loosen belt tension and remove belt.
2. Loosen set screw on fan motor.
3. Open sheave to desired position.
4. Retighten set screw and replace belt.
NOTE: Set belt tension as outlined below.
BELT TENSION ADJUSTMENT — An overly loose belt
will, upon starting motor, produce a slippage “squeal” and
18
Table 5 — 50VQP084 Blower Performance Data
AIRFLOW
(l/s)
755.2
802.4
849.6
896.8
944.0
991.2
1038.4
1085.6
1132.8
1180.0
1227.2
1274.4
1321.6
1368.8
1416.0
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.18
B
353
4..5
0.21
B
362
4
0.22
B
377
3.5
0.25
B
381
3.5
0.25
B
390
3
0.29
B
399
2.5
0.32
B
412
2.5
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.11
B
352
4.5
0.12
B
362
4.5
0.17
B
375
4
0.18
B
387
3.5
0.22
B
403
3
0.23
B
411
2.5
0.25
B
420
2
0.28
B
423
2
0.29
B
431
1.5
0.33
B
440
1.5
0.37
B
455
1
50
0.12
B
388
3.5
0.13
B
392
3
0.14
B
395
2.5
0.15
B
399
2.5
0.16
B
403
2.5
0.18
B
410
2
0.21
B
424
2
0.22
B
435
1.5
0.25
B
446
1.5
0.25
B
452
1
0.32
A
460
5.5
0.32
A
463
5.5
0.33
A
474
5
0.37
A
481
5
0.40
A
492
4.5
75
0.15
B
437
1.5
0.16
B
440
1.5
0.17
B
444
1
0.18
B
447
1
0.19
A
450
5.5
0.22
A
457
5.5
0.24
A
467
5
0.25
A
476
5
0.29
A
485
4.5
0.29
A
495
4.5
0.36
A
500
4
0.36
A
504
4
0.37
A
510
3.5
0.40
A
517
3.5
0.44
A
526
3
100
0.13
A
482
5
0.15
A
485
5
0.17
A
488
5
0.19
A
491
4.5
0.21
A
493
4.5
0.25
A
499
4.5
0.25
A
507
4
0.29
A
518
4
0.33
A
527
3.5
0.33
A
532
3.5
0.40
A
536
3
0.40
A
539
3
0.40
A
545
2.5
0.44
A
551
2
0.48
A
563
2
125
0.19
A
527
3.5
0.20
A
529
3.5
0.22
A
530
3.5
0.23
A
532
3
0.25
A
534
3
0.28
A
537
3
0.29
A
548
2.5
0.33
A
555
2.5
0.37
A
563
2.5
0.37
A
567
2
0.43
A
570
2
0.44
A
576
1.5
0.48
A
581
1.5
0.48
A
586
1
0.52
A
595
1
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
0.22
0.24
0.26
0.30
A
A
C
C
564
599
630
663
2.5
1.5
5.5
4.5
0.24
0.25
0.28
0.32
A
A
C
C
566
601
633
666
2
1.5
5.5
4.5
0.25
0.27
0.29
0.33
A
A
C
C
568
603
636
668
2
1
5
4
0.27
0.28
0.31
0.35
A
C
C
C
571
606
639
671
2
5.5
5
4
0.28
0.30
0.33
0.37
A
C
C
C
573
608
641
673
2
5.5
4.5
4
0.31
0.33
0.37
0.40
A
C
C
C
577
612
647
678
1.5
5.5
4.5
3.5
0.33
0.37
0.40
0.44
A
C
C
C
584
621
653
684
1.5
5
4.5
3.5
0.37
0.40
0.44
0.48
A
C
C
C
590
627
659
692
1.5
5
4
3
0.40
0.44
0.48
0.52
A
C
C
C
600
633
665
697
1
5
4
3
0.40
0.44
0.48
0.55
A
C
C
C
604
636
670
700
1
4.5
4
3
0.47
0.51
0.55
0.58
C
C
C
C
606
638
671
701
5.5
4.5
3.5
2.5
0.48
0.52
0.55
0.59
C
C
C
C
609
641
674
703
5.5
4.5
3.5
2.5
0.52
0.55
0.59
0.63
C
C
C
C
613
647
677
706
5.5
4
3.5
2.5
0.55
0.59
0.63
0.67
C
C
C
C
618
651
681
710
5
4
3
2
0.55
0.63
0.67
0.70
C
C
C
C
628
658
687
718
5
4
3
2
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
250
0.31
C
690
3.5
0.34
C
693
3
0.36
C
697
3
0.38
C
700
3
0.40
C
703
2.5
0.44
C
710
2.5
0.48
C
716
2.5
0.52
C
721
2
0.55
C
726
2
0.59
C
729
2
0.62
C
729
2
0.63
C
734
1.5
0.67
C
737
1.5
0.70
C
740
1.5
0.78
E
745
1.5
275
0.33
C
716
2.5
0.36
C
720
2.5
0.38
C
723
2
0.41
C
727
2
0.43
C
730
2
0.48
C
737
1.5
0.52
C
743
1.5
0.55
C
751
1.5
0.59
C
756
1.5
0.63
C
759
1
0.66
C
759
1
0.67
C
762
1
0.70
C
764
1
0.78
E
767
1
0.82
E
774
1
300
0.37
C
744
2
0.40
C
747
2
0.42
C
751
1.5
0.45
C
754
1.5
0.47
C
757
1.5
0.52
C
764
1
0.55
C
772
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
0.39
C
767
1
0.42
C
771
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor, E = High Rpm/Large Motor.
19
Table 6 — 50VQP096 Blower Performance Data
AIRFLOW
(l/s)
849.6
896.8
944.0
991.2
1038.4
1085.6
1132.8
1180.0
1227.2
1274.4
1321.6
1368.8
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.16
B
339
5
0.18
B
353
4.5
0.21
B
362
4.0
0.22
B
377
3.5
0.25
B
381
3.5
0.25
B
390
3
0.29
B
399
3
25
0.10
B
343
5
0.11
B
348
4.5
0.11
B
352
4.5
0.12
B
362
4
0.17
B
375
4
0.18
B
387
3.5
0.22
B
403
3
0.23
B
411
2.5
0.25
B
420
2
0.28
B
423
2
0.29
B
431
2
0.33
A
440
6
50
0.14
B
395
3
0.15
B
399
3
0.16
B
403
3
0.18
B
410
2.5
0.21
B
424
2
0.22
A
435
6
0.25
A
446
6
0.25
A
452
5.5
0.32
A
460
5.5
0.32
A
463
5
0.33
A
474
5
0.37
A
481
4.5
75
0.17
A
444
6
0.18
A
447
6
0.19
A
450
5.5
0.22
A
457
5.5
0.24
A
467
5
0.25
A
476
5
0.29
A
485
5
0.29
A
495
4.5
0.36
A
500
4.5
0.36
A
504
4
0.37
A
510
4
0.40
A
517
3.5
100
0.17
A
488
5
0.19
A
491
5
0.21
A
493
4.5
0.25
A
499
4.5
0.25
A
507
4.5
0.29
A
518
4
0.33
A
527
3.5
0.33
A
532
3.5
0.40
A
536
3
0.40
A
539
3
0.40
A
545
3
0.44
A
551
2.5
125
0.22
A
530
3.5
0.23
A
532
3.5
0.25
A
534
3
0.28
A
537
3
0.29
A
548
3
0.33
A
555
2.5
0.37
A
563
2.5
0.37
A
567
2
0.43
A
570
2
0.44
A
576
1.5
0.48
A
581
1.5
0.48
A
586
1.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.25
0.27
0.29
0.33
0.36
A
A
C
C
C
568
603
636
668
697
2.5
1.5
5
4
3
0.27
0.28
0.31
0.35
0.38
A
A
C
C
C
571
606
639
671
700
2
1.5
5
4
3
0.28
0.30
0.33
0.37
0.40
A
A
C
C
C
573
608
641
673
703
2
1
5
4
2.5
0.31
0.33
0.37
0.40
0.44
A
A
C
C
C
577
612
647
678
710
2
1
4.5
3.5
2.5
0.33
0.37
0.40
0.44
0.48
A
A
C
C
C
584
621
653
684
716
1.5
1
4.5
3.5
2.5
0.37
0.40
0.44
0.48
0.52
A
C
C
C
C
590
627
659
692
721
1.5
5.5
4.5
3
2.5
0.40
0.44
0.48
0.52
0.55
A
C
C
C
C
600
633
665
697
726
1.5
5.5
4
3
2
0.40
0.44
0.48
0.55
0.59
A
C
C
C
C
604
636
670
700
729
1
5
4
3
2
0.47
0.51
0.55
0.58
0.62
A
C
C
C
C
606
638
671
701
729
1
5
3.5
2.5
2
0.48
0.52
0.55
0.59
0.63
A
C
C
C
C
609
641
674
703
734
1
5
3.5
2.5
2
0.52
0.55
0.59
0.63
0.67
A
C
C
C
C
613
647
677
706
737
1
4.5
3.5
2.5
2
0.55
0.59
0.63
0.67
0.70
C
C
C
C
C
618
651
681
710
740
5.5
4.5
3
2.5
1.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
275
0.38
C
723
2.5
0.41
C
727
2.5
0.43
C
730
2
0.48
C
737
2
0.52
C
743
2
0.55
C
751
1.5
0.59
C
756
1.5
0.63
C
759
1
0.66
C
759
1
0.67
C
762
1
—
—
—
—
—
—
—
—
300
0.42
C
751
1.5
0.45
C
754
1.5
0.47
C
757
1.5
0.52
C
764
1
0.55
C
772
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor.
20
Table 6 — 50VQP096 Blower Performance Data (cont)
AIRFLOW
(l/s)
1416.0
1463.2
1510.4
1557.6
1604.8
1652.0
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
0.32
B
412
2.5
0.33
B
421
2
0.37
A
441
6
0.40
A
456
5.5
0.47
A
471
5.5
0.48
A
486
5
25
0.37
A
455
5.5
0.40
A
459
5.5
0.40
A
478
5
0.48
A
495
4.5
0.52
A
506
4
0.55
A
520
3.5
50
0.40
A
492
4.5
0.44
A
499
4
0.48
A
513
4
0.52
A
529
3.5
0.55
A
539
3
0.59
A
555
2.5
75
0.44
A
526
3.5
0.48
A
533
3
0.52
A
549
2.5
0.55
A
561
2
0.59
A
574
1.5
0.63
A
586
1
100
0.48
A
563
2
0.52
A
569
2
0.55
A
581
1.5
0.62
A
595
1
0.63
A
604
1
0.70
C
615
5.5
125
0.52
A
595
1
0.55
A
600
1
0.63
A
614
1
0.67
C
625
5.5
0.70
C
633
5
0.74
C
647
4.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
0.55
0.63
0.67
0.70
C
C
C
C
628
658
687
718
5
4
3
2
0.63
0.67
0.70
0.74
C
C
C
C
633
663
691
722
5
4
3
2
0.67
0.70
0.74
0.78
C
C
C
C
644
672
703
730
4.5
3.5
2.5
2
0.70
0.74
0.78
0.85
C
C
C
C
656
685
712
741
4
3
2.5
2
0.74
0.78
0.85
0.89
C
C
C
C
664
692
721
747
4
3
2
1.5
0.78
0.85
0.92
0.96
C
C
C
C
674
704
730
756
4
3
2
1.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
250
0.78
C
745
1.5
0.78
C
749
1.5
0.85
C
759
1.5
0.92
C
767
1
0.93
C
773
1
—
—
—
—
275
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
300
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor.
21
Table 7 — 50VQP120 Blower Performance Data
AIRFLOW
(l/s)
1085.6
1132.8
1180.0
1227.2
1274.4
1321.6
1368.8
1416.0
1463.2
1510.4
1557.6
1604.8
1652.0
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.25
B
377
6
0.30
B
395
5.5
0.33
B
414
4.5
0.37
B
431
4
0.40
B
448
3.5
0.44
B
464
3
0.48
B
480
2.5
0.52
B
496
2
25
—
—
—
—
—
—
—
—
—
—
—
—
0.22
B
385
6
0.25
B
403
5
0.30
B
421
4.5
0.33
B
438
4
0.37
B
453
3.5
0.40
B
469
3
0.44
B
485
2
0.48
B
500
1.5
0.52
A
515
6
0.55
A
530
5.5
50
0.18
B
376
6
0.19
B
395
5.5
0.22
B
412
5
0.25
B
430
4
0.30
B
446
3.5
0.33
B
462
3
0.37
B
478
2.5
0.40
B
491
2
0.44
A
504
6
0.48
A
520
5.5
0.52
A
537
5
0.55
A
551
4.5
0.63
A
565
4
75
0.19
B
423
4.5
0.22
B
439
4
0.25
B
455
3
0.30
B
471
2.5
0.33
B
486
2
0.37
A
501
6
0.40
A
515
6
0.44
A
529
5.5
0.48
A
542
5
0.52
A
556
4.5
0.55
A
570
4
0.63
A
583
3.5
0.67
A
596
3.5
100
0.22
B
466
3
0.27
B
481
2.5
0.30
B
496
1.5
0.33
A
506
6
0.37
A
520
5.5
0.40
A
534
5
0.45
A
547
4.5
0.48
A
563
4.5
0.52
A
575
4
0.55
A
588
3.5
0.63
A
601
3
0.67
A
613
3
0.70
A
625
2.5
125
0.27
A
503
6
0.30
A
517
5.5
0.33
A
530
5.5
0.37
A
544
5
0.40
A
556
4.5
0.45
A
569
4
0.48
A
582
3.5
0.52
A
595
3.5
0.55
A
607
3
0.63
A
619
2.5
0.67
A
631
2
0.70
A
642
2
0.78
A
654
1.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.30
0.34
0.37
0.42
0.45
A
A
A
A
A
543
580
616
649
682
5
4
3
2
1
0.34
0.37
0.42
0.45
0.52
A
A
A
A
C
555
592
626
659
691
4.5
3.5
2.5
1.5
6
0.37
0.40
0.45
0.48
0.55
A
A
A
A
C
567
603
637
669
701
4
3
2
1
6
0.40
0.45
0.48
0.55
0.60
A
A
A
A
C
579
614
647
679
710
3.5
2.5
1.5
1
5.5
0.45
0.48
0.55
0.60
0.63
A
A
A
C
C
591
625
657
689
719
3.5
2.5
1
6
5.5
0.48
0.52
0.60
0.63
0.67
A
A
A
C
C
603
636
668
698
728
3
2
1
6
5
0.52
0.55
0.63
0.67
0.70
A
A
A
C
C
615
647
678
708
737
2.5
1.5
1
5.5
5
0.55
0.63
0.67
0.70
0.78
A
A
C
C
C
626
659
689
717
745
2.5
1.5
6
5.5
4.5
0.63
0.67
0.70
0.78
0.82
A
A
C
C
C
637
670
699
726
754
2
1
6
5
4.5
0.67
0.70
0.78
0.82
0.85
A
A
C
C
C
649
680
708
736
765
1.5
1
5.5
5
4
0.70
0.78
0.82
0.85
0.93
A
C
C
C
C
662
691
718
745
774
1.5
6
5.5
4.5
4
0.78
0.82
0.85
0.93
0.96
A
C
C
C
C
674
701
728
754
783
1
6
5
4.5
3.5
0.82
0.85
0.93
0.96
1.00
C
C
C
C
C
684
711
738
766
792
6
5.5
4.5
4
3
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
0.48
C
712
5.5
0.52
C
722
5.5
0.60
C
730
5
0.63
C
739
4.5
0.67
C
748
4.5
0.70
C
757
4
0.75
C
765
4
0.82
C
774
3.5
0.85
C
783
3.5
0.93
C
791
3
0.96
C
799
3
1.00
C
808
2.5
1.08
C
816
2.5
300
0.52
C
742
4.5
0.57
C
751
4.5
0.63
C
759
4
0.67
C
768
4
0.70
C
776
3.5
0.75
C
785
3.5
0.78
C
793
3
0.85
C
801
3
0.89
C
809
2.5
0.96
C
817
2.5
1.00
C
824
2
1.08
C
833
2
1.15
C
841
1.5
325
0.55
C
770
4
0.60
C
779
3.5
0.67
C
787
3.5
0.70
C
795
3
0.75
C
803
3
0.78
C
812
2.5
0.85
C
819
2.5
0.89
C
826
2
0.93
C
834
2
1.00
C
841
1.5
1.08
C
849
1.5
1.11
C
857
1
1.19
C
867
1
350
0.60
C
797
3
0.67
C
805
3
0.70
C
813
2.5
0.75
C
822
2
0.78
C
830
2
0.82
C
838
1.5
0.90
C
845
1.5
0.93
C
851
1
1.00
C
859
1
1.08
C
868
0.5
1.11
C
875
0.5
1.15
C
882
0
1.23
C
890
0
375
0.63
C
822
2.5
0.70
C
831
2
0.75
C
839
1.5
0.78
C
847
1.5
0.82
C
855
1
0.90
C
860
1
0.93
C
868
0.5
1.00
C
877
0.5
1.08
C
884
0.5
1.14
C
891
0
1.15
C
898
0
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor, E = High Rpm/Large Motor.
22
Table 7 — 50VQP120 Blower Performance Data (cont)
AIRFLOW
(l/s)
1699.2
1746.4
1793.6
1840.8
1888.0
1935.2
1982.4
2029.6
2076.8
2124.0
2029.6
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
0.55
A
511
6
0.63
A
526
5.5
0.67
A
544
5
0.70
A
555
4.5
0.78
A
572
4
0.85
A
589
3.5
0.93
A
605
3
0.96
A
621
2.5
1.040
A
637
2
1.11
A
653
1.5
0.96
A
621
2.5
25
0.63
A
544
5
0.67
A
561
4.5
0.70
A
575
4
0.78
A
589
3.5
0.82
A
601
3
0.89
A
617
2.5
0.96
A
633
2
1.00
A
649
1.5
1.08
A
664
1
1.15
A
679
1
1.00
A
649
1.5
50
0.67
A
578
3.5
0.70
A
592
3.5
0.78
A
605
3
0.85
A
618
2.5
0.85
A
630
2
0.93
A
645
1.5
1.00
A
660
1
1.08
A
675
1
1.15
C
690
6
1.23
C
707
5.5
1.08
A
675
1
75
0.70
A
608
3
0.78
A
621
2.5
0.82
A
633
2
0.89
A
646
1.5
0.93
A
657
1
1.00
A
672
1
1.08
C
689
6
1.15
C
703
6
1.23
C
717
5.5
1.30
C
731
5
1.15
C
703
6
100
0.78
A
637
2
0.85
A
649
1.5
0.85
A
661
1
0.93
A
676
6
1.00
C
686
6
1.08
C
700
6
1.15
C
714
5.5
1.23
C
728
5
1.30
C
742
4.5
1.38
C
755
4
1.23
C
728
5
125
0.82
A
668
1
0.89
A
679
1
0.93
C
691
6
1.00
C
702
6
1.08
C
712
5.5
1.11
C
726
5
1.19
C
739
4.5
1.26
C
752
4
1.38
C
766
4
1.45
C
779
3.5
1.26
C
752
4
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.85
0.93
1.00
1.04
1.08
C
C
C
C
C
695
722
748
776
800
6
5
4.5
3.5
3
0.93
1.00
1.04
1.08
1.15
C
C
C
C
C
706
732
758
785
809
5.5
5
4
3.5
2.5
1.00
1.04
1.08
1.15
1.23
C
C
C
C
C
717
742
767
794
818
5.5
4.5
4
3
2
1.08
1.11
1.15
1.23
1.30
C
C
C
C
C
728
753
779
803
827
5
4
3.5
2.5
2
1.11
1.15
1.23
1.30
1.34
C
C
C
C
C
737
762
789
812
836
4.5
4
3
2.5
1.5
1.15
1.23
1.30
1.38
1.41
C
C
C
C
C
751
775
801
824
847
4.5
3.5
2.5
2
1
1.23
1.30
1.38
1.50
1.53
C
C
C
E
E
763
790
813
836
858
4
3
2
1.5
1
1.30
1.38
1.50
1.53
1.60
C
C
E
E
E
776
802
827
847
869
3.5
2.5
2
1.5
1
1.41
1.50
1.53
1.60
1.68
C
E
C
E
E
791
814
836
858
882
3
2
2
1
0.5
1.53
1.56
1.60
1.68
1.75
E
E
C
E
E
804
826
848
870
893
3
2
1.5
1
0
1.30
1.38
1.50
1.53
1.60
C
C
E
E
E
776
802
827
847
869
3.5
2.5
2
1.5
1
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
1.15
C
825
2
1.23
C
833
2
1.26
C
842
1.5
1.34
C
850
1
1.38
C
859
1
1.50
E
872
0.5
1.56
E
882
0.5
1.68
E
893
0
1.75
E
904
0
—
—
—
—
1.68
E
893
0
300
1.19
C
849
1.5
1.26
C
857
1
1.30
C
867
0.5
1.38
C
875
0.5
1.50
E
883
0
1.53
E
894
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
1.23
C
874
0.5
1.30
C
882
0.5
1.38
C
890
0
1.45
E
898
0
1.53
E
905
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
1.30
C
897
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor, E = High Rpm/Large Motor.
23
Table 8 — 50VQP150 Blower Performance Data
AIRFLOW
(l/s)
1321.6
1368.8
1416.0
1463.2
1510.4
1557.6
1604.8
1652.0
1699.2
1746.4
1793.6
1840.8
1888.0
1935.2
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.63
B
523
6
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.55
B
519
6
0.59
B
531
5.5
0.63
B
545
5
0.70
B
560
4.5
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.52
B
526
6
0.55
B
541
5.5
0.63
B
554
5
0.63
B
569
4.5
0.70
B
582
4
0.78
B
596
3.5
75
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.45
B
522
6
0.48
B
537
5.5
0.52
B
551
5
0.55
B
565
4.5
0.63
B
579
4
0.67
B
591
3.5
0.70
A
605
6
0.78
A
618
5.5
0.82
A
631
5.5
100
—
—
—
—
—
—
—
—
0.37
B
521
6
0.42
B
536
5.5
0.45
B
548
5
0.48
B
562
4.5
0.52
B
576
4
0.57
B
589
3.5
0.60
A
600
6
0.67
A
613
5.5
0.70
A
626
5.5
0.78
A
639
5
0.85
A
651
4.5
0.85
A
661
4.5
125
0.34
B
533
5.5
0.37
B
544
5
0.42
B
558
4.5
0.45
B
572
4
0.49
B
585
3.5
0.52
A
599
6
0.57
A
612
5.5
0.60
A
622
5.5
0.67
A
634
5
0.70
A
647
4.5
0.78
A
659
4.5
0.85
A
669
4
0.89
A
683
4
0.93
A
692
3.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.37
0.42
0.49
0.52
0.57
B
A
A
A
A
572
606
640
676
712
4
6
5
4
3
0.42
0.45
0.52
0.57
0.60
B
A
A
A
A
582
619
652
686
719
4
5.5
4.5
3.5
2.5
0.45
0.52
0.57
0.60
0.67
B
A
A
A
A
595
628
663
697
728
3.5
5.5
4.5
3.5
2.5
0.52
0.55
0.60
0.64
0.72
A
A
A
A
A
608
640
674
705
737
6
5
4
3
2
0.55
0.60
0.67
0.70
0.75
A
A
A
A
A
618
652
685
715
747
5.5
4.5
3.5
2.5
1.5
0.60
0.64
0.70
0.78
0.82
A
A
A
A
A
631
664
694
725
756
5.5
4
3
2.5
1.5
0.63
0.67
0.75
0.82
0.85
A
A
A
A
A
643
676
705
736
763
5
4
3
2
1
0.67
0.75
0.78
0.85
0.93
A
A
A
A
A
655
685
716
746
776
4.5
3.5
2.5
2
1
0.75
0.78
0.85
0.93
0.97
A
A
A
A
C
665
696
727
754
783
4
3
2
1.5
6
0.78
0.85
0.93
0.97
1.00
A
A
A
A
C
677
707
737
764
793
4
3
2
1.5
6
0.85
0.93
0.96
1.00
1.08
A
A
A
A
C
688
718
746
774
802
3.5
2.5
2
1
5.5
0.89
0.93
1.00
1.08
1.15
A
A
A
A
C
702
729
757
785
811
3
2.5
1.5
1
5.5
0.93
1.00
1.08
1.15
1.23
A
A
A
C
C
710
739
767
794
821
3
2
1.5
6
5.5
1.00
1.08
1.15
1.23
1.26
A
A
A
C
C
722
750
778
804
831
2.5
1.5
1
6
5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
0.64
A
746
2
0.67
A
754
1.5
0.75
A
762
1.5
0.78
A
769
1
0.85
A
778
1
0.90
A
784
1
0.93
C
793
6
1.00
C
802
6
1.05
C
809
5.5
1.08
C
818
5.5
1.15
C
829
5
1.23
C
838
5
1.26
C
845
4.5
1.30
C
854
4.5
300
0.72
A
783
1
0.75
A
789
1
0.79
C
796
6
0.82
C
799
6
0.90
C
807
5.5
0.93
C
815
5.5
1.00
C
823
5
1.05
C
829
5
1.08
C
837
4.5
1.15
C
846
4.5
1.23
C
855
4.5
1.30
C
862
4
1.30
C
870
4
1.38
C
879
3.5
325
0.79
C
821
5.5
0.81
C
823
5.5
0.82
C
828
5
0.90
C
832
5
0.97
C
836
5
1.00
C
845
4.5
1.08
C
850
4.5
1.12
C
858
4
1.15
C
865
4
1.23
C
871
3.5
1.30
C
879
3.5
1.38
C
887
3.5
1.38
C
895
3
1.45
C
904
3
350
0.87
C
859
4.5
0.90
C
860
4
0.94
C
863
4
0.97
C
866
4
1.05
C
868
3.5
1.08
C
874
3.5
1.15
C
880
3.5
1.20
C
886
3
1.23
C
891
3
1.30
C
898
3
1.38
C
905
2.5
1.45
C
913
2.5
1.45
C
920
2.5
1.53
C
928
2
375
0.94
C
901
3
0.97
C
902
3
1.02
C
903
3
1.05
C
904
3
1.12
C
905
3
1.15
C
906
3
1.20
C
908
2.5
1.23
C
913
2.5
1.30
C
919
2.5
1.38
C
926
2
1.45
C
931
2
1.52
C
938
2
1.53
C
945
2
1.60
C
951
1.5
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor, E = High Rpm/Large Motor.
24
Table 8 — 50VQP150 Blower Performance Data (cont)
AIRFLOW
(l/s)
1982.4
2029.6
2076.8
2124.0
2171.2
2218.4
2265.6
2312.8
2360.0
2407.2
2454.4
2501.6
2548.8
2596.0
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
0.70
B
538
5.5
0.70
B
553
5
0.78
B
568
4.5
0.85
B
581
4
0.89
B
598
3.5
0.93
A
605
6
1.00
A
618
5.5
1.08
A
631
5.5
1.15
A
642
5
1.23
A
655
4.5
1.30
A
668
4
1.38
A
680
3.5
1.45
A
691
3.5
1.53
A
704
3
25
0.74
B
574
4
0.78
B
588
3.5
0.85
B
602
3
0.90
A
613
6
0.93
A
623
5.5
1.00
A
637
5
1.08
A
647
4.5
1.15
A
662
4
1.23
A
672
4
1.30
A
685
3.5
1.38
A
697
3
1.45
A
709
3
1.53
A
717
2.5
1.60
A
729
2
50
0.78
A
609
6
0.85
A
620
5.5
0.93
A
633
5
0.97
A
646
4.5
1.00
A
656
4.5
1.08
A
666
4
1.15
A
678
4
1.23
A
690
3.5
1.30
A
702
3
1.38
A
714
2.5
1.45
A
726
2.5
1.53
A
737
2
1.60
A
745
1.5
1.68
A
756
1.5
75
0.85
A
640
5
0.93
A
653
4.5
1.00
A
666
4
1.05
A
678
4
1.08
A
687
3.5
1.15
A
697
3
1.23
A
708
3
1.30
A
720
2.5
1.38
A
731
2
1.45
A
743
1.5
1.53
A
752
1.5
1.60
A
763
1
1.68
A
772
1
1.75
C
783
6
100
0.93
A
673
4
1.00
A
685
3.5
1.08
A
697
3.5
1.12
A
706
3
1.15
A
715
2.5
1.23
A
727
2.5
1.30
A
738
2
1.38
A
749
1.5
1.45
A
760
1.5
1.53
A
769
1
1.60
C
782
6
1.68
C
790
6
1.75
C
799
5.5
1.83
C
810
5.5
125
1.00
A
703
3
1.08
A
715
2.5
1.15
A
726
2.5
1.20
A
735
2
1.23
A
744
2
1.30
A
755
1.5
1.38
A
766
1
1.45
A
777
1
1.53
C
785
6
1.60
C
798
6
1.68
C
806
5.5
1.75
C
817
5.5
1.83
C
825
5
1.90
C
836
5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
1.08
1.15
1.19
1.23
1.30
A
A
A
C
C
733
761
788
812
838
2
1.5
1
5.5
5
1.15
1.19
1.23
1.30
1.38
A
A
C
C
C
744
771
796
822
847
2
1
6
5.5
4.5
1.19
1.23
1.30
1.38
1.45
A
A
C
C
C
755
782
806
832
857
1.5
1
6
5
4.5
1.27
1.35
1.42
1.50
1.57
A
C
C
C
C
763
791
817
842
867
1.5
6
5.5
4.5
4
1.30
1.38
1.45
1.53
1.60
A
C
C
C
C
772
799
825
850
872
1
6
5.5
4.5
3.5
1.38
1.45
1.53
1.60
1.68
A
C
C
C
C
783
809
835
858
882
1
5.5
5
4
3.5
1.45
1.53
1.60
1.68
1.75
C
C
C
C
C
793
819
844
867
891
6
5.5
4.5
4
3
1.53
1.60
1.68
1.75
1.83
C
C
C
C
C
803
827
852
877
900
6
5
4.5
3.5
3
1.60
1.68
1.75
1.83
1.90
C
C
C
C
C
811
837
862
886
909
5.5
4.5
4
3
2.5
1.68
1.75
1.83
1.90
1.97
C
C
C
C
C
822
847
872
896
917
5
4.5
3.5
3
2.5
1.75
1.83
1.90
1.97
2.05
C
C
C
C
C
832
857
882
903
926
5
4
3.5
2.5
2
1.83
1.90
1.97
2.05
2.12
C
C
C
C
C
842
867
889
912
935
4.5
4
3
2
2
1.90
1.97
2.05
2.12
2.20
C
C
C
C
C
850
873
897
920
943
4.5
3.5
3
2
1.5
1.97
2.05
2.12
2.31
2.35
C
C
C
E
E
859
883
907
929
952
4
3.5
2.5
1
0.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
1.38
C
863
4
1.45
C
872
4
1.53
C
881
3.5
1.65
C
889
3
1.68
C
896
3
1.75
C
905
2.5
1.83
C
914
2.5
1.90
C
923
2
1.97
C
932
1.5
2.05
C
940
1.5
2.12
C
949
1
2.20
C
957
C
2.31
E
965
0
2.42
E
972
0
300
1.45
C
888
3.5
1.53
C
896
3
1.60
C
904
3
1.72
C
912
2.5
1.75
C
919
2
1.83
C
928
2
1.90
C
937
1.5
1.97
C
946
1.5
2.05
C
953
1
2.12
C
962
1
2.24
E
971
0
2.31
E
979
0
—
—
—
—
—
—
—
—
325
1.53
C
912
2.5
1.60
C
919
2.5
1.68
C
927
2
1.80
C
935
2
1.83
C
942
1.5
1.90
C
951
1.5
1.97
C
959
1.5
2.05
C
966
1
2.12
C
975
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
1.60
C
934
2
1.68
C
942
1.5
1.75
C
950
1.5
1.87
C
958
1.5
1.90
C
963
1
1.97
C
973
1
2.05
C
980
1
2.12
C
988
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
1.68
C
958
1.5
1.75
C
966
1
1.83
C
973
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor, E = High Rpm/Large Motor.
25
Table 9 — 50VQP168 Blower Performance Data
AIRFLOW
(l/s)
1510.4
1604.8
1699.2
1793.6
1888.0
1982.4
2076.8
2171.2
2265.6
2360.0
2454.4
2548.8
2643.2
2737.6
2832.0
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.42
B
362
6
0.43
B
377
6
0.49
B
381
5.5
0.51
B
390
5.5
0.58
B
399
5
0.64
B
412
5
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.24
B
362
6
0.34
B
375
6
0.36
B
387
5.5
0.43
B
403
5.5
0.46
B
411
5
0.51
B
420
4.5
0.57
B
423
4.5
0.58
B
431
4
0.66
B
440
4
0.73
B
455
3.5
50
0.23
B
388
6
0.25
B
392
5.5
0.27
B
395
5.5
0.29
B
399
5.5
0.32
B
403
5
0.36
B
410
5
0.42
B
424
4.5
0.43
B
435
4
0.51
B
446
4
0.51
B
452
3.5
0.64
B
460
3.5
0.64
B
463
3
0.66
B
474
3
0.73
B
481
2.5
0.81
B
492
2
75
0.30
B
437
4
0.32
B
440
4
0.34
B
444
4
0.37
B
447
3.5
0.39
B
450
3.5
0.43
B
457
3.5
0.47
B
467
3
0.51
B
476
3
0.58
B
485
2.5
0.58
B
495
2
0.72
B
500
2
0.72
B
504
1.5
0.73
B
510
1.5
0.81
A
517
5.5
0.88
A
526
5.5
100
0.26
B
482
2.5
0.30
B
485
2.5
0.34
B
488
2.5
0.39
B
491
2
0.43
B
493
2
0.51
B
499
2
0.51
B
507
1.5
0.58
B
518
1.5
0.66
A
527
5.5
0.66
A
532
5.5
0.79
A
536
5
0.79
A
539
5
0.81
A
545
5
0.88
A
551
4.5
0.96
A
563
4
125
0.38
A
527
5.5
0.41
A
529
5.5
0.44
A
530
5.5
0.47
A
532
5
0.50
A
534
5
0.55
A
537
5
0.58
A
548
4.5
0.66
A
555
4.5
0.73
A
563
4.5
0.73
A
567
4
0.87
A
570
4
0.88
A
576
3.5
0.96
A
581
3.5
0.96
A
586
3.5
1.03
A
595
3
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
0.45
0.48
0.51
0.60
A
A
A
A
564
599
630
663
4.5
3.5
2.5
1.5
0.48
0.51
0.55
0.63
A
A
A
A
566
601
633
666
4.5
3.5
2.5
1.5
0.50
0.54
0.59
0.67
A
A
A
A
568
603
636
668
4
3.5
2.5
1
0.53
0.57
0.62
0.70
A
A
A
A
571
606
639
671
4
3
2
1
0.56
0.60
0.66
0.74
A
A
A
A
573
608
641
673
4
3
2
1
0.61
0.66
0.73
0.81
A
A
A
A
577
612
647
678
3.5
3
2
1
0.66
0.73
0.81
0.88
A
A
A
C
584
621
653
684
3.5
2.5
1.5
3.5
0.73
0.81
0.88
0.96
A
A
A
C
590
627
659
692
3.5
2.5
1.5
3
0.81
0.88
0.96
1.03
A
A
A
C
600
633
665
697
3
2.5
1
3
0.81
0.88
0.96
1.11
A
A
A
C
604
636
670
700
3
2
1
3
0.94
1.02
1.09
1.17
A
A
C
C
606
638
671
701
3
2
4
2.5
0.96
1.03
1.11
1.18
A
A
C
C
609
641
674
703
2.5
2
3.5
2.5
1.03
1.11
1.18
1.26
A
A
C
C
613
647
677
706
2.5
1.5
3.5
2.5
1.11
1.18
1.26
1.33
A
A
C
C
618
651
681
710
2.5
1.5
3.5
2
1.11
1.26
1.33
1.41
A
A
C
C
628
658
687
718
2
1
3
2
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
250
0.63
C
690
3.5
0.67
C
693
3
0.71
C
697
3
0.76
C
700
3
0.80
C
703
2.5
0.88
C
710
2.5
0.96
C
716
2.5
1.03
C
721
2.5
1.11
C
726
2
1.18
C
729
2
1.24
C
729
2
1.26
C
734
1.5
1.33
C
737
1.5
1.41
C
740
1.5
1.56
C
745
1
275
0.66
C
716
2.5
0.71
C
720
2.5
0.76
C
723
2.5
0.81
C
727
2
0.86
C
730
2
0.96
C
737
2
1.03
C
743
1.5
1.11
C
751
1.5
1.18
C
756
1.5
1.26
C
759
1
1.32
C
759
1
1.33
C
762
1
—
—
—
—
—
—
—
—
—
—
—
—
300
0.75
C
744
2
0.80
C
747
2
0.84
C
751
1.5
0.89
C
754
1.5
0.94
C
757
1.5
1.03
C
764
1
1.11
C
772
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
0.78
C
767
1
0.84
C
771
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open.
Other speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea
level conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High
Rpm/Standard Motor
26
Table 10 — 50VQP192 Blower Performance Data
AIRFLOW
(l/s)
1699.2
1793.6
1888.0
1982.4
2076.8
2171.2
2265.6
2360.0
2454.4
2548.8
2643.2
2737.6
2832.0
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.42
B
362
6
0.43
B
377
6
0.49
B
381
6
0.51
B
390
5.5
0.58
B
399
5.5
0.64
B
412
5
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.34
B
375
6
0.36
B
387
6
0.43
B
403
5.5
0.46
B
411
5
0.51
B
420
4.5
0.57
B
423
4.5
0.58
B
431
4.5
0.66
B
440
4
0.73
B
455
3.5
50
0.27
B
395
5.5
0.29
B
399
5.5
0.32
B
403
5.5
0.36
B
410
5
0.42
B
424
4.5
0.43
B
435
4
0.51
B
446
4
0.51
B
452
3.5
0.64
B
460
3.5
0.64
B
463
3
0.66
B
474
3
0.73
B
481
2.5
0.81
B
492
2
75
0.34
B
444
4
0.37
B
447
4
0.39
B
450
3.5
0.43
B
457
3.5
0.47
B
467
3
0.51
B
476
3
0.58
B
485
2.5
0.58
B
495
2
0.72
B
500
2
0.72
A
504
6
0.73
A
510
6
0.81
A
517
5.5
0.88
A
526
5.5
100
0.34
B
488
2.5
0.39
B
491
2.5
0.43
B
493
2
0.51
B
499
2
0.51
B
507
1.5
0.58
A
518
6
0.66
A
527
5.5
0.66
A
532
5.5
0.79
A
536
5
0.79
A
539
5
0.81
A
545
4.5
0.88
A
551
4.5
0.96
A
563
4
125
0.44
A
530
5.5
0.47
A
532
5.5
0.50
A
534
5
0.55
A
537
5
0.58
A
548
5
0.66
A
555
4.5
0.73
A
563
4.5
0.73
A
567
4
0.87
A
570
4
0.88
A
576
3.5
0.96
A
581
3.5
0.96
A
586
3.5
1.03
A
595
3
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.50
0.54
0.59
0.67
0.71
A
A
A
A
C
568
603
636
668
697
4
3.5
2
1
3
0.53
0.57
0.62
0.70
0.76
A
A
A
A
C
571
606
639
671
700
4
3
2
1
3
0.56
0.60
0.66
0.74
0.80
A
A
A
A
C
573
608
641
673
703
4
3
2
1
2.5
0.61
0.66
0.73
0.81
0.88
A
A
A
A
C
577
612
647
678
710
3.5
3
1.5
1
2.5
0.66
0.73
0.81
0.88
0.96
A
A
A
C
C
584
621
653
684
716
3.5
2.5
1.5
3.5
2.5
0.73
0.81
0.88
0.96
1.03
A
A
A
C
C
590
627
659
692
721
3.5
2.5
1.5
3
2.5
0.81
0.88
0.96
1.03
1.11
A
A
A
C
C
600
633
665
697
726
3.5
2.5
1
3
2
0.81
0.88
0.96
1.11
1.18
A
A
A
C
C
604
636
670
700
729
3
2
1
3
2
0.94
1.02
1.09
1.17
1.24
A
A
C
C
C
606
638
671
701
729
3
2
3.5
2.5
2
0.96
1.03
1.11
1.18
1.26
A
A
C
C
C
609
641
674
703
734
3
2
3.5
2.5
2
1.03
1.11
1.18
1.26
1.33
A
A
C
C
C
613
647
677
706
737
3
1.5
3.5
2.5
1.5
1.11
1.18
1.26
1.33
1.41
A
A
C
C
C
618
651
681
710
740
2.5
1.5
3
2.5
1.5
1.11
1.26
1.33
1.41
1.56
A
A
C
C
C
628
658
687
718
745
2
1
3
2
1.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
275
0.76
C
723
2.5
0.81
C
727
2
0.86
C
730
2
0.96
C
737
2
1.03
C
743
1.5
1.11
C
751
1.5
1.18
C
756
1.5
1.26
C
759
1
1.32
C
759
1
1.33
C
762
1
—
—
—
—
—
—
—
—
—
—
—
—
300
0.84
C
751
1.5
0.89
C
754
1.5
0.94
C
757
1.5
1.03
C
764
1
1.11
C
772
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor.
27
Table 10 — 50VQP192 Blower Performance Data (cont)
AIRFLOW
(l/s)
2926.4
3020.8
3115.2
3209.6
3304.0
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
0.66
B
421
4.5
0.73
B
441
4
0.81
B
456
3.5
0.94
B
471
3
0.96
B
486
2.5
25
0.79
B
459
3.5
0.81
B
478
2.5
0.96
B
495
2
1.03
A
506
6
1.11
A
520
5.5
50
0.88
B
499
2
0.96
A
513
6
1.03
A
529
5.5
1.11
A
539
5
1.18
A
555
4.5
75
0.96
A
533
5
1.03
A
549
4.5
1.11
A
561
4
1.18
A
574
3.5
1.26
A
586
3
100
1.03
A
569
4
1.11
A
581
3.5
1.24
A
595
3
1.26
A
604
3
1.41
A
615
2.5
125
1.11
A
600
3
1.26
A
614
3
1.33
A
625
2.5
1.41
A
633
2
1.48
A
647
1.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
1.26
1.33
1.41
1.48
A
A
C
C
633
663
691
722
2
1
2.5
2
1.33
1.41
1.48
1.56
A
C
C
C
644
672
703
730
1.5
3.5
2.5
2
1.41
1.48
1.56
1.71
A
C
C
C
656
685
712
741
1
3.5
2.5
2
1.48
1.56
1.71
1.78
A
C
C
C
664
692
721
747
1
3
2
2
1.56
1.71
1.84
1.93
A
C
C
C
674
704
730
756
1
3
2
1.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
250
1.56
C
749
1.5
1.71
C
759
1
1.84
C
767
1
1.86
C
773
1
—
—
—
—
275
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
300
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor.
28
Table 11 — 50VQP240 Blower Performance Data
AIRFLOW
(l/s)
2171.2
2265.6
2360.0
2454.4
2548.8
2643.2
2737.6
2832.0
2926.4
3020.8
3115.2
3209.6
3304.0
3398.4
3492.8
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.73
B
431
6
0.81
B
448
5.5
0.88
B
464
5
0.96
B
480
4.5
1.03
B
496
4
1.11
B
511
3.5
1.26
B
526
3
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.60
B
421
6
0.66
B
438
6
0.73
B
453
5.5
0.81
B
469
4
0.88
B
485
4.5
0.96
B
500
4
1.03
B
515
3
1.11
B
530
2.5
1.26
A
544
6
1.33
A
561
5.5
50
—
—
—
—
—
—
—
—
—
—
—
—
0.51
B
430
6
0.60
B
446
6
0.66
B
462
5
0.75
B
478
4.5
0.81
B
491
4
0.88
B
504
3.5
0.96
B
520
3
1.03
A
537
6
1.11
A
551
5.5
1.26
A
565
5.5
1.33
A
578
5
1.41
A
592
4.5
75
0.39
B
423
6
0.45
B
439
6
0.51
B
455
5.5
0.60
B
471
4.5
0.66
B
486
4
0.75
B
501
3.5
0.81
B
515
3
0.88
B
529
2.5
0.96
A
542
6
1.03
A
556
5.5
1.11
A
570
5
1.26
A
583
4.5
1.33
A
596
4
1.41
A
608
4
1.56
A
621
3.5
100
0.45
B
466
5
0.54
B
481
4.5
0.60
B
496
4
0.66
B
506
3.5
0.75
B
520
3
0.81
A
534
6
0.90
A
547
5.5
0.96
A
563
5.5
1.03
A
575
5
1.11
A
588
4.5
1.26
A
601
4.5
1.33
A
613
4
1.41
A
625
3.5
1.56
A
637
3
1.71
A
649
3
125
0.54
B
503
3.5
0.60
B
517
3
0.66
A
530
6
0.75
A
544
6
0.81
A
556
5.5
0.90
A
569
5
0.96
A
582
4.5
1.03
A
595
4.5
1.11
A
607
4
1.26
A
619
3.5
1.33
A
631
3.5
1.41
A
642
3
1.56
A
654
2.5
1.63
A
668
2
1.78
A
679
2
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
0.60
0.69
0.75
0.84
A
A
A
A
543
580
616
649
6
5
4
3
0.69
0.75
0.84
0.90
A
A
A
A
555
592
626
659
5.5
4.5
3.5
2.5
0.75
0.81
0.90
0.96
A
A
A
A
567
603
637
669
5
4
3
2
0.81
0.90
0.96
1.11
A
A
A
A
579
614
647
679
5
3.5
3
2
0.90
0.96
1.11
1.20
A
A
A
A
591
625
657
689
4.5
3.5
2.5
1.5
0.96
1.05
1.20
1.26
A
A
A
A
603
636
668
698
4
3
2
1.5
1.05
1.11
1.26
1.35
A
A
A
A
615
647
678
708
3.5
3
2
1
1.11
1.26
1.33
1.41
A
A
A
A
626
659
689
717
3.5
2.5
1.5
1
1.26
1.33
1.41
1.56
A
A
A
C
637
670
699
726
3
2
1.5
5.5
1.33
1.41
1.56
1.63
A
A
A
C
649
680
708
736
3
2
1
5
1.41
1.56
1.63
1.71
A
A
A
C
662
691
718
745
2.5
1.5
1
4.5
1.56
1.63
1.71
1.86
A
A
C
C
674
701
728
754
2
1.5
5
4.5
1.63
1.71
1.86
1.93
A
A
C
C
684
711
738
766
1.5
1
5
4
1.71
1.86
2.00
2.08
A
C
C
C
695
722
748
776
1.5
5.5
4.5
3.5
1.86
2.00
2.08
2.15
A
C
C
C
706
732
758
785
1
5
4
3.5
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
250
0.90
A
682
2
1.05
A
691
1.5
1.11
A
701
1.5
1.20
A
710
1
1.26
C
719
5.5
1.35
C
728
5
1.41
C
737
5
1.56
C
745
4.5
1.63
C
754
4.5
1.71
C
765
4
1.86
C
774
3.5
1.93
C
783
3.5
2.00
C
792
3
2.15
C
800
3
2.30
C
809
2.5
275
0.96
A
712
1
1.05
A
722
1
1.20
C
730
5
1.26
C
739
5
1.35
C
748
4.5
1.41
C
757
4
1.50
C
765
4
1.63
C
774
3.5
1.71
C
783
3.5
1.86
C
791
3
1.93
C
799
3
2.00
C
808
2.5
2.15
C
816
2.5
2.30
C
825
2
2.45
C
833
2
300
1.05
C
742
4.5
1.14
C
751
4.5
1.26
C
759
4
1.35
C
768
4
1.41
C
776
3.5
2.00
C
785
2.618
2.08
C
793
2.244
2.28
C
801
2.244
2.38
C
809
1.87
2.58
C
817
2.5
2.68
C
616
2
2.88
C
623
2
3.08
C
629
1.5
3.18
C
635
1.5
3.38
C
857
1
325
1.11
C
770
4
1.20
C
779
3.5
1.35
C
787
3.5
1.41
C
795
3
1.50
C
803
3
2.08
C
812
1.87
2.28
C
819
1.87
2.38
C
826
1.496
2.48
C
834
1.496
2.68
C
841
1.5
2.88
C
635
1.5
2.98
C
641
1
3.18
C
649
1
3.28
C
654
0.5
3.48
C
882
0.5
350
1.20
C
797
3
1.35
C
805
3
1.41
C
813
2.5
1.50
C
822
2
1.56
C
830
2
2.20
C
838
1.122
2.40
C
845
1.122
2.48
C
851
1.122
2.68
C
859
0.748
2.88
C
868
1
2.98
C
654
0.5
3.08
C
660
0.5
3.28
C
666
0
3.48
C
671
0
—
—
—
—
375
1.26
C
822
2.5
1.41
C
831
2
1.50
C
839
1.5
1.56
C
847
1.5
1.65
C
855
1
2.40
C
860
0.748
2.48
C
868
0.748
2.68
C
877
0.374
2.88
C
884
0.374
3.06
C
891
0.5
3.08
C
671
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor.
29
Table 11 — 50VQP240 Blower Performance Data (cont)
AIRFLOW
(l/s)
3587.2
3681.6
3776.0
3870.4
3964.8
4059.2
4153.6
4248.0
A
B
bhp
C
ESP
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
1.33
A
544
6
1.41
A
555
5.5
1.56
A
572
5
1.71
A
589
4.5
1.86
A
605
4
1.93
A
621
3.5
2.08
A
637
3
2.23
A
653
2.5
25
1.41
A
575
5
1.56
A
589
4.5
1.63
A
601
4
1.78
A
617
3.5
1.93
A
633
3
2.00
A
649
2.5
2.15
A
664
2
2.30
A
679
1.5
50
1.56
A
605
4
1.71
A
618
3.5
1.71
A
630
3
1.86
A
645
3
2.00
A
660
2.5
2.15
A
675
2
2.30
A
690
1.5
2.45
A
707
1
75
1.63
A
633
3
1.78
A
646
2.5
1.86
A
657
2.5
2.00
A
672
2
2.15
A
689
1.5
2.30
A
703
1
2.45
C
717
5.5
2.60
C
731
5
100
1.71
A
661
2.5
1.86
A
676
2
2.00
A
686
1.5
2.15
A
700
1
2.30
A
714
1
2.45
C
728
5
2.60
C
742
4.5
2.75
C
755
4
125
1.86
A
691
1.5
2.00
A
702
1
2.15
A
712
1
2.23
C
726
5
2.38
C
739
5
2.53
C
752
4.5
2.75
C
766
4
2.90
C
779
3.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
2.00
2.08
2.15
2.30
2.45
A
C
C
C
C
717
742
767
794
818
1
4.5
4
3
2.5
2.15
2.23
2.30
2.45
2.60
C
C
C
C
C
728
753
779
803
827
5
4.5
3.5
2.5
2
2.23
2.30
2.45
2.60
2.68
C
C
C
C
C
737
762
789
812
836
4.5
4
3
2.5
1.5
2.30
2.45
2.60
2.75
2.83
C
C
C
C
C
751
775
801
824
847
4.5
3.5
2.5
2
1.5
2.45
2.60
2.75
2.99
3.05
C
C
C
C
C
763
790
813
836
858
4
3
2.5
1.5
1
2.60
2.75
2.99
3.05
3.20
C
C
C
C
C
776
802
827
847
869
3.5
2.5
2
1.5
1
2.83
2.99
3.05
3.20
3.35
C
C
C
C
C
791
814
836
858
882
3
2.5
2
1
0.5
3.05
3.13
3.20
3.35
3.50
C
C
C
C
C
804
826
848
870
893
3
2
1.5
1
0
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
External Static Pressure
275
2.53
C
842
1.5
2.68
C
850
1
2.75
C
859
1
2.90
C
872
0.5
3.13
C
882
0.5
3.35
C
893
0
3.50
C
904
0
—
—
—
—
300
2.60
C
867
1
2.75
C
875
0.5
2.90
C
883
0.5
3.05
C
894
0
3.20
C
904
0
—
—
—
—
—
—
—
—
—
—
—
—
325
2.75
C
890
0
2.90
C
898
0
3.05
C
905
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor.
30
Table 12 — 50VQP300 Blower Performance Data
AIRFLOW
(l/s)
2643.2
2737.6
2832.0
2926.4
3020.8
3115.2
3209.6
3304.0
3398.4
3492.8
3587.2
3681.6
3776.0
3870.4
A
B
bhp
C
E
ESP
—
—
—
—
—
—
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.26
B
523
6
25
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.18
B
531
6
1.26
B
545
5
1.41
B
560
4.5
50
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1.05
B
526
6
1.11
B
541
5
1.26
B
554
5
1.26
B
569
4.5
1.41
B
582
4
1.56
B
596
3.5
75
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.90
B
522
6
0.96
B
537
5.5
1.05
B
551
5
1.11
B
565
4.5
1.26
B
579
4
1.33
B
591
3.5
1.41
B
605
3
1.56
B
618
2.5
1.63
B
631
2
100
—
—
—
—
—
—
—
—
0.75
B
521
6
0.84
B
536
5.5
0.90
B
548
5
0.96
B
562
4.5
1.05
B
576
4
1.14
B
589
3.5
1.20
B
600
3
1.35
B
613
2.5
1.41
B
626
2
1.56
A
639
6
1.71
A
651
5.5
1.71
A
661
5
125
0.69
B
533
5.5
0.75
B
544
5
0.84
B
558
4.5
0.90
B
572
4
0.99
B
585
3.5
1.05
B
599
3
1.14
B
612
2.5
1.20
B
622
2
1.35
A
634
6
1.41
A
647
5.5
1.56
A
659
5
1.71
A
669
5
1.78
A
683
4.5
1.86
A
692
4
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
0.75
0.84
0.99
1.05
1.14
B
B
A
A
A
572
606
640
676
712
4
3
6
4.5
3.5
0.84
0.90
1.05
1.14
1.20
B
B
A
A
A
582
619
652
686
719
4
2.5
5.5
4
3
0.90
1.05
1.14
1.20
1.35
B
B
A
A
A
595
628
663
697
728
3
2
5
4
2.5
1.05
1.11
1.20
1.29
1.44
B
A
A
A
A
608
640
674
705
737
3
6
4.5
3.5
2.5
1.11
1.20
1.35
1.41
1.50
B
A
A
A
A
618
652
685
715
747
2.5
5.5
4
3
2
1.20
1.29
1.41
1.56
1.65
A
A
A
A
A
631
664
694
725
756
6
5
4
3
1.5
1.26
1.35
1.50
1.65
1.71
A
A
A
A
A
643
676
705
736
763
5.5
4.5
3.5
2.5
1.5
1.35
1.50
1.56
1.71
1.86
A
A
A
A
A
655
685
716
746
776
5
4
3
2
1
1.50
1.56
1.71
1.86
1.94
A
A
A
A
A
665
696
727
754
783
5
4
3
2
1
1.56
1.71
1.86
1.94
2.00
A
A
A
A
A
677
707
737
764
793
4.5
3.5
2.5
1.5
0.5
1.71
1.86
1.93
2.00
2.15
A
A
A
A
A
688
718
746
774
802
4
3
2
1
0
1.78
1.86
2.00
2.15
2.30
A
A
A
A
A
702
729
757
785
811
3.5
3
2
1
0
1.86
2.00
2.15
2.30
2.45
A
A
A
A
C
710
739
767
794
821
3.5
2.5
1.5
0.5
2.5
2.00
2.15
2.30
2.45
2.53
A
A
A
A
C
722
750
778
804
831
3
2
1
0
2
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
1.29
A
746
2
1.35
A
754
2
1.50
A
762
1.5
1.56
A
769
1.5
1.71
A
778
1
1.80
A
784
1
1.86
A
793
0.5
2.00
A
802
0
2.09
A
809
0
2.15
C
818
2.5
2.30
C
829
2
2.45
C
838
2
2.53
C
845
1.5
2.60
C
854
1.5
300
1.44
A
783
1
1.50
A
789
0.5
1.59
A
796
0.5
1.65
A
799
0
1.80
A
807
0
2.48
C
815
2
2.68
C
823
2
2.80
C
829
1.5
2.88
C
837
1.5
3.08
C
846
1.5
3.28
C
640
1.5
3.48
C
645
1
3.48
C
651
1
3.68
C
657
0.5
325
1.59
A
821
0
1.62
C
823
2.5
1.65
C
828
2
1.80
C
832
2
1.94
C
836
2
2.68
C
845
1
2.88
C
850
1
3.00
C
858
1
3.08
C
865
1
3.28
C
871
0.5
3.48
C
657
0.5
3.68
C
663
0.5
3.68
C
669
0
3.88
C
676
0
350
1.74
C
859
1.5
1.80
C
860
1.5
1.88
C
863
1
1.94
C
866
1
2.09
C
868
1
2.88
C
874
0.5
3.08
C
880
0.5
3.20
C
886
0
3.28
C
891
0
3.48
C
898
0
3.68
C
677
0
—
—
—
—
—
—
—
—
—
—
—
—
375
1.88
C
901
0.5
1.94
C
902
0
2.03
C
903
0
2.09
C
904
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor, E = High Rpm/Large Motor.
31
Table 12 — 50VQP300 Blower Performance Data (cont)
AIRFLOW
(l/s)
3964.8
4059.2
4153.6
4248.0
4342.4
4436.8
4531.2
4625.6
4720.0
4814.4
4908.8
5003.2
5097.6
5192.0
A —
B —
bhp —
C —
E
—
ESP —
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
BkW
Sheave/Mtr
RPM
Turns Open
0
1.41
B
538
5.5
1.41
B
553
5
1.56
B
568
4.5
1.71
B
581
4
1.78
B
598
3.5
1.86
B
605
3
2.00
B
618
2.5
2.15
A
631
6
2.30
A
642
6
2.45
A
655
5.5
2.60
A
668
5
2.75
A
680
4.5
2.90
A
691
4
3.05
A
704
3.5
25
1.48
B
574
4
1.56
B
588
3.5
1.71
B
602
3
1.80
B
613
2.5
1.86
B
623
2.5
2.00
A
637
6
2.15
A
647
5.5
2.30
A
662
5
2.45
A
672
4.5
2.60
A
685
4
2.75
A
697
4
2.90
A
709
3.5
3.05
A
717
3
3.20
A
729
2.5
50
1.56
B
609
3
1.71
B
620
2.5
1.86
A
633
6
1.94
A
646
5.5
2.00
A
656
5
2.15
A
666
5
2.30
A
678
4.5
2.45
A
690
4
2.60
A
702
3.5
2.75
A
714
3
2.90
A
726
2.5
3.05
A
737
2.5
3.20
A
745
2
3.35
A
756
1.5
75
1.71
A
640
6
1.86
A
653
5.5
2.00
A
666
5
2.09
A
678
4.5
2.15
A
687
4
2.30
A
697
4
2.45
A
708
3.5
2.60
A
720
3
2.75
A
731
2.5
2.90
A
743
2
3.05
A
752
2
3.20
A
763
1.5
3.35
A
772
1
3.50
A
783
1
100
1.86
A
673
4.5
2.00
A
685
4
2.15
A
697
4
2.24
A
706
3.5
2.30
A
715
3
2.45
A
727
3
2.60
A
738
2.5
2.75
A
749
2
2.90
A
760
2
3.05
A
769
1.5
3.20
A
782
1
3.35
A
790
0.5
3.50
A
799
0
3.65
A
810
0
125
2.00
A
703
3.5
2.15
A
715
3
2.30
A
726
3
2.39
A
735
2.5
2.45
A
744
2.5
2.60
A
755
2
2.75
A
766
1.5
2.90
A
777
1
3.05
A
785
1
3.20
A
798
0.5
3.35
A
806
0
3.50
C
817
2.5
3.65
C
825
2
3.80
E
836
1.5
EXTERNAL STATIC PRESSURE (Pa)
150
175
200
225
250
2.15
2.30
2.38
2.45
2.60
A
A
A
A
C
733
761
788
812
838
2.5
1.5
1
0
2
2.30
2.38
2.45
2.60
2.75
A
A
A
C
C
744
771
796
822
847
2.5
1.5
0.5
2.5
1.5
2.38
2.45
2.60
2.75
2.90
A
A
A
C
C
755
782
806
832
857
2
1
0
2
1.5
2.54
2.69
2.84
2.99
3.14
A
A
C
C
C
763
791
817
842
867
1.5
1
2.5
2
1
2.60
2.75
2.90
3.05
3.20
A
A
C
C
C
772
799
825
850
872
1
0.5
2
1.5
1
2.75
2.90
3.05
3.20
3.35
A
A
C
C
C
783
809
835
858
882
1
0
2
1.5
0.5
2.90
3.05
3.20
3.35
3.50
A
C
C
C
C
793
819
844
867
891
0.5
2.5
1.5
1
0.5
3.05
3.20
3.35
3.50
3.65
A
C
C
C
C
803
827
852
877
900
0
2
1.5
0.5
0
3.20
3.35
3.50
3.65
—
A
C
C
C
—
811
837
862
886
—
0
2
1
0.5
—
3.35
3.50
3.65
3.80
—
C
C
C
E
—
822
847
872
896
—
2.5
1.5
0.5
0
—
3.50
3.65
3.80
—
—
C
C
E
—
—
832
857
882
—
—
2
1
0.5
—
—
3.65
3.80
3.95
—
—
C
E
E
—
—
842
867
889
—
—
1.5
1
0
—
—
3.80
3.95
4.10
—
—
E
E
E
—
—
850
873
897
—
—
1.5
0.5
0
—
—
3.95
4.10
—
—
—
E
E
—
—
—
859
883
—
—
—
1
0.5
—
—
—
LEGEND
Standard rpm/Standard Motor
Low rpm/Standard Motor
Brake Horsepower
High rpm/Standard Motor
High rpm/Large Motor
External Static Pressure
275
2.75
C
863
1
2.90
C
872
1
3.05
C
881
0.5
3.29
C
889
0
3.35
C
896
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
300
3.88
C
888
0.5
3.05
C
896
0
3.20
C
904
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
325
4.08
C
912
0
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
375
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
1. Unit is factory shipped with standard static sheave and drive at 2.5 turns open. Other
speeds require field selection.
2. For applications requiring higher static pressures, contact your local Carrier representative. Performance data does not include drive losses and is based on sea level
conditions.
3. All airflow is rated at lowest voltage. If unit is dual voltage rated, data is based on
lowest voltage.
4. A = Standard Rpm/Standard Motor, B = Low Rpm/Standard Motor, C = High Rpm/
Standard Motor, E = High Rpm/Large Motor.
32
Deluxe D Control DIP Switches — The Deluxe D
FIELD SELECTABLE INPUTS
control has 2 DIP switch blocks. Each DIP switch block has
8 switches and is labeled either S1 or S2 on the circuit board.
See Fig. 28.
DIP SWITCH BLOCK 1 (S1) — This set of switches offers
the following options for Deluxe D control configuration:
Performance Monitor (PM) — Set switch 1 to enable or disable performance monitor. To enable the PM, set the switch to
ON. To disable the PM, set the switch to OFF.
Compressor Relay Staging Operation — Switch 2 will enable
or disable compressor relay staging operation. The compressor
relay can be set to turn on with stage 1 or stage 2 call from the
thermostat. This setting is used with dual stage units (units with
2 compressors and 2 Deluxe D controls) or in master/slave applications. In master/slave applications, each compressor and
fan will stage according to its switch 2 setting. If switch is set to
stage 2, the compressor will have a 3-second delay before energizing during stage 2 demand.
NOTE: If DIP switch is set for stage 2, the alarm relay will not
cycle during Test mode.
Heating/Cooling Thermostat Type — Switch 3 provides selection of thermostat type. Heat pump or heat/cool thermostats
can be selected. Select OFF for heat/cool thermostats. When in
heat/cool mode, Y1 is used for cooling stage 1, Y2 is used for
cooling stage 2, W1 is used for heating stage 1 and O/W2 is
used for heating stage 2. Select ON for heat pump applications.
In heat pump mode, Y1 used is for compressor stage 1, Y2 is
used for compressor stage 2, W1 is used for heating stage 3 or
emergency heat, and O/W2 is used for RV (heating or cooling)
depending upon switch 4 setting.
O/B Thermostat Type — Switch 4 provides selection for heat
pump O/B thermostats. O is cooling output. B is heating output. Select ON for heat pumps with O output. Select OFF for
heat pumps with B output.
Dehumidification Fan Mode — Switch 5 provides selection
of normal or dehumidification fan mode. Select OFF for dehumidification mode. The fan speed relay will remain OFF during cooling stage 2. Select ON for normal mode. The fan speed
relay will turn on during cooling stage 2 in normal mode.
Switch 6 — Not used.
Boilerless Operation — Switch 7 provides selection of boilerless operation and works in conjunction with switch 8. In
boilerless operation mode, only the compressor is used for
heating when FP1 is above the boilerless changeover temperature set by switch 8 below. Select ON for normal operation or
select OFF for boilerless operation.
Boilerless Changeover Temperature — Switch 8 on S1 provides selection of boilerless changeover temperature set point.
Select OFF for set point of 10.0 C or select ON for set point
of 4.4 C.
If switch 8 is set for 10.0 C, then the compressor will be
used for heating as long as the FP1 is above 10.0 C. The compressor will not be used for heating when the FP1 is below
10.0 C and the compressor will operate in emergency heat
mode, staging on EH1 and EH2 to provide heat. If a thermal
switch is being used instead of the FP1 thermistor, only the
compressor will be used for heating mode when the FP1 terminals are closed. If the FP1 terminals are open, the compressor is
not used and the control goes into emergency heat mode.
DIP SWITCH BLOCK 2 (S2) — This set of DIP switches is
used to configure accessory relay options. See Fig. 28.
Switches 1 to 3 — These DIP switches provide selection of
Accessory 1 relay options. See Table 13 for DIP switch
combinations.
Switches 4 to 6 — These DIP switches provide selection
of Accessory 2 relay options. See Table 14 for DIP switch
combinations.
Jumpers and DIP (dual in-line package) switches on the
control board are used to customize unit operation and can be
configured in the field.
IMPORTANT: Jumpers and DIP switches should only be
clipped when power to control board has been turned off.
Complete C Control Jumper Settings (See
Fig. 27)
WATER COIL FREEZE PROTECTION (FP1) LIMIT
SETTING — Select jumper 3, (JW3-FP1 Low Temp) to
choose FP1 limit of –12.2 C or –1.1 C. To select –1.1 C as the
limit, DO NOT clip the jumper. To select –12.2 C as the limit,
clip the jumper.
AIR COIL FREEZE PROTECTION (FP2) LIMIT SETTING — Select jumper 2 (JW2-FP2 Low Temp) to choose
FP2 limit of –12.2 C or –1.1 C. To select –1.1 C as the limit,
DO NOT clip the jumper. To select –12.2 C as the limit, clip
the jumper.
ALARM RELAY SETTING — Select jumper 1 (JW1-AL2
Dry) for connecting alarm relay terminal (AL2) to 24 vac (R) or
to remain as a dry contact (no connection). To connect AL2 to
R, do not clip the jumper. To set as dry contact, clip the jumper.
Complete C Control DIP Switches — The Complete C control has 1 DIP switch block with five switches. See
Fig. 27.
PERFORMANCE MONITOR (PM) — DIP switch 1 will
enable or disable this feature. To enable the PM, set the switch
to ON. To disable the PM, set the switch to OFF.
STAGE 2 — DIP switch 2 will enable or disable compressor
delay. Set DIP switch to OFF for stage 2 in which the compressor will have a 3-second delay before energizing.
NOTE: The alarm relay will not cycle during Test mode if
switch is set to OFF, stage 2.
DIP SWITCH 3 — not used.
DIP SWITCH 4 — not used.
DIP SWITCH 5 — DIP switch 5 is used to initiate 1 or 3 tries
for the FP1 fault. If water freeze protection for the water coil
then DIP switch 5 can be set to lock out on the FP1 fault after
one try.
Deluxe D Control Jumper Settings (See
Fig. 28)
WATER COIL FREEZE PROTECTION (FP1) LIMIT
SETTING — Select jumper 3, (JW3-FP1 Low Temp) to
choose FP1 limit of –12.2 C or –1.1 C. To select –1.1 C as the
limit, DO NOT clip the jumper. To select –12.2 C as the limit,
clip the jumper.
AIR COIL FREEZE PROTECTION (FP2) LIMIT SETTING — Select jumper 2 (JW2-FP2 Low Temp) to choose
FP2 limit of –12.2 C or –1.1 C. To select –1.1 C as the limit,
DO NOT clip the jumper. To select –12.2 C as the limit, clip
the jumper.
ALARM RELAY SETTING — Select jumper 4 (JW4-AL2
Dry) for connecting alarm relay terminal (AL2) to 24 vac (R) or
to remain as a dry contact (no connection). To connect AL2 to
R, do not clip the jumper. To set as dry contact, clip the jumper.
LOW PRESSURE SETTING — The Deluxe D Control can
be configured for Low Pressure Setting (LP). Select jumper 1
(JW1-LP Norm Open) for choosing between low pressure input normally opened or closed. To configure for normally
closed operation, do not clip the jumper. To configure for normally open operation, clip the jumper.
33
Auto Dehumidification Mode or High Fan Mode — Switch 7
provides selection of auto dehumidification fan mode or high
fan mode. In auto dehumidification fan mode the fan speed
relay will remain off during cooling stage 2 if terminal H is
active. In high fan mode, the fan enable and fan speed relays
will turn on when terminal H is active. Set the switch to ON for
auto dehumidification fan mode or to OFF for high fan mode.
Switch 8 — Not used.
CAUTION
To avoid equipment damage, DO NOT leave system filled
in a building without heat during the winter unless antifreeze is added to system water. Condenser coils never
fully drain by themselves and will freeze unless winterized
with antifreeze.
Table 13 — DIP Switch Block S2 —
Accessory 1 Relay Options
ACCESSORY 1
RELAY OPTIONS
Cycle with Fan
Digital NSB
Water Valve — Slow Opening
OAD
START-UP
Use the procedure outlined below to initiate proper unit
start-up.
NOTE: This equipment is designed for indoor installation only.
DIP SWITCH POSITION
1
2
3
On
On
On
Off
On
On
On
Off
On
On
On
Off
Operating Limits
ENVIRONMENT — This equipment is designed for indoor
installation ONLY. Extreme variations in temperature, humidity and corrosive water or air will adversely affect the unit performance, reliability and service life.
POWER SUPPLY — A voltage variation of ± 10% of nameplate utilization voltage is acceptable.
UNIT STARTING CONDITIONS — All units start and operate in an ambient of 7.2 C with entering-air at 4.4 C, enteringwater at –6.7 C and with both air and water at the flow rates
used.
NOTE: These operating conditions are not normal or continuous operating conditions. It is assumed that such a start-up is
for the purpose of bringing the building space up to occupancy
temperature.
LEGEND
NSB — Night Setback
OAD — Outside Air Damper
NOTE: All other DIP switch combinations are invalid.
Table 14 — DIP Switch Block S2 —
Accessory 2 Relay Options
ACCESSORY 2
RELAY OPTIONS
Cycle with Fan
Digital NSB
Water Valve — Slow Opening
OAD
DIP SWITCH POSITION
4
5
6
On
On
On
Off
On
On
On
Off
On
On
On
Off
WARNING
LEGEND
NSB — Night Setback
OAD — Outside Air Damper
When the disconnect switch is closed, high voltage is
present in some areas of the electrical panel. Exercise
caution when working with the energized equipment.
NOTE: All other switch combinations are invalid.
Start Up System
Deluxe D Control Accessory Relay Configurations — The following accessory relay settings are applica-
1.
2.
3.
4.
Restore power to system.
Turn thermostat fan position to ON. Blower should start.
Balance airflow at registers.
Adjust all valves to the full open position and turn on the
line power to all heat pump units.
5. Operate unit in the cooling cycle. Room temperature
should be approximately 10 to 38 C dry bulb. Loop water
temperature entering the heat pumps should be between
10 and 49 F.
NOTE: Three factors determine the operating limits of a
unit: (1) entering-air temperature, (2) water temperature and
(3) ambient temperature. Whenever any of these factors are
at a minimum or maximum level, the other two factors must
be at a normal level to ensure proper unit operation. See
Table 15.
ble for both Deluxe D controls only:
CYCLE WITH FAN — In this configuration, the relay will be
ON any time the Fan Enable relay is on.
CYCLE WITH COMPRESSOR — In this configuration, the
relay will be ON any time the Compressor relay is on.
DIGITAL NIGHT SET BACK (NSB) — In this configuration, the relay will be ON if the NSB input is connected to
ground C.
NOTE: If there are no relays configured for digital NSB, then
the NSB and override (OVR) inputs are automatically configured for mechanical operation.
MECHANICAL NIGHT SET BACK — When NSB input is
connected to ground C, all thermostat inputs are ignored. A
thermostat set back heating call will then be connected to the
OVR input. If OVR input becomes active, then the Deluxe D
control will enter Night Low Limit (NLL) staged heating
mode. The NLL staged heating mode will then provide heating
during the NSB period.
WATER VALVE (SLOW OPENING) — If relay is configured for Water Valve (slow opening), the relay will start 60 seconds prior to starting compressor relay.
OUTSIDE AIR DAMPER (OAD) — If relay is configured
for OAD, the relay will normally be ON any time the Fan
Enable relay is energized. The relay will not start for 30 minutes following a return to normal mode from NSB, when NSB
is no longer connected to ground C. After 30 minutes, the relay
will start if the Fan Enable is set to ON.
Scroll Compressor Rotation — It is important to be
certain compressor is rotating in the proper direction. To
determine whether or not compressor is rotating in the proper
direction:
1. Connect service gages to suction and discharge pressure
fittings.
2. Energize the compressor.
3. The suction pressure should drop and the discharge
pressure should rise, as is normal on any start-up.
34
Unit Start-Up Heating Mode
Table 15 — 50VQP Unit Operating Limits
AIR LIMITS
Minimum Ambient Air db
Rated Ambient Air db
Maximum Ambient Air db
Minimum Return Air db/wb
Maximum Return Air db/wb
WATER LIMITS
Standard Unit
Minimum Entering Water*
Maximum Entering Water
Extended Range Unit†
Minimum Entering Water*
Maximum Entering Water
COOLING (C)
10
27
38
18/15
43/28
HEATING (C)
10
20
29
16
29
10
49
16
43
–1
49
–6.7
43
NOTE: Operate the unit in heating cycle after checking the
cooling cycle. Allow 5 minutes between tests for the pressure
or reversing valve to equalize.
1. Turn thermostat to lowest setting and set thermostat
switch to HEAT position.
2. Slowly turn the thermostat to a higher temperature until
the compressor activates.
3. Check for warm air delivery at the unit grille within a few
minutes after the unit has begun to operate.
4. Check the temperature of both supply and discharge water. If temperature is within acceptable range, proceed. If
temperature is outside the range, check the heating refrigerant pressures.
5. Once the unit has begun to run, check for warm air delivery at the unit grille.
6. Check air temperature rise across the coil when compressor is operating. Air temperature rise should be between
11° C and 17° C after 15 minutes at load.
7. Check for vibration, noise and water leaks.
Flow Regulation — Flow regulation can be accomplished by two methods. Most water control valves have a flow
adjustment built into the valve. By measuring the pressure drop
through the unit heat exchanger, the flow rate can be determined using Table 17. Adjust the water control valve until the
flow of 0.09 to 0.13 L/s is achieved. Since the pressure constantly varies, two pressure gages may be needed in some
applications.
An alternative method is to install a flow control device.
These devices are typically an orifice of plastic material designed to allow a specified flow rate that are mounted on the
outlet of the water control valve. Occasionally these valves
produce a velocity noise that can be reduced by applying
some back pressure. To accomplish this, slightly close the
leaving isolation valve of the well water setup.
LEGEND
db — Dry Bulb
wb — Wet Bulb
*Requires optional insulation package when operating below the
dew point.
†With antifreeze, optional extended range insulation and low temperature cutout jumper clipped for antifreeze.
If the suction pressure does not drop and the discharge
pressure does not rise to normal levels:
1. Turn off power to the unit. Install disconnect tag.
2. Reverse any two of the unit power leads.
3. Reapply power to the unit and verify pressures are correct.
The suction and discharge pressure levels should now move
to their normal start-up levels.
When the compressor is rotating in the wrong direction, the
unit makes an elevated level of noise and does not provide
cooling.
After a few minutes of reverse operation, the scroll compressor internal overload protection will open, thus activating
the unit lockout. This requires a manual reset. To reset, turn the
thermostat on and then off.
NOTE: There is a 5-minute time delay before the compressor
will start.
WARNING
To avoid possible injury or death due to electrical shock,
open the power supply disconnect switch and secure it in
an open position before flushing system.
Unit Start-Up Cooling Mode
1. Adjust the unit thermostat to the warmest position.
Slowly reduce the thermostat position until the compressor activates.
2. Check for cool air delivery at unit grille a few minutes
after the unit has begun to operate.
3. Verify that the compressor is on and that the water flow
rate is correct by measuring pressure drop through the
heat exchanger using P/T plugs. See Table 16. Check the
elevation and cleanliness of the condensate lines; any
dripping could be a sign of a blocked line. Be sure the
condensate trap includes a water seal.
4. Check the temperature of both supply and discharge water. If temperature is within acceptable range, proceed. If
temperature is outside the range, check the cooling refrigerant pressures.
5. Check air temperature drop across the coil when compressor is operating. Air temperature drop should be
between 8 and 14 C.
Flushing — Once the piping is complete, final purging
and loop charging is needed. A flush cart pump of at least
1.5 hp is needed to achieve adequate flow velocity in the
loop to purge air and dirt particles from the loop. Flush the
loop in both directions with a high volume of water at a high
velocity. Follow the steps below to properly flush the loop:
1. Verify power is off.
2. Fill loop with water from hose through flush cart before using flush cart pump to ensure an even fill. Do
not allow the water level in the flush cart tank to drop
below the pump inlet line to prevent air from filling
the line.
3. Maintain a fluid level in the tank above the return tee
to avoid air entering back into the fluid.
4. Shutting off the return valve that connects into the
flush cart reservoir will allow 345 kPa surges to help
purge air pockets. This maintains the pump at 345 kPa.
5. To purge, keep the pump at 345 kPa until maximum
pumping pressure is reached.
6. Open the return valve to send a pressure surge through
the loop to purge any air pockets in the piping system.
7. A noticeable drop in fluid level will be seen in the
flush cart tank. This is the only indication of air in the
loop.
Table 16 — Water Temperature Change
Through Heat Exchanger
WATER FLOW RATE (GPM)
For Closed Loop: Ground Source or
Cooling/Boiler Systems at 3.9 L/m per kW
For Open Loop: Ground Water Systems at
2.0 L/m per kW
COOLING
RISE (C)
Min
Max
HEATING
DROP (C)
Min
Max
5.0
6.7
2.2
6.1
10.0
12.8
3.9
11.1
35
Table 19 to determine the amount of antifreeze to use. Antifreeze concentration should be checked from a well mixed
sample using a hydrometer to measure specific gravity. .
Table 17 — Coaxial Water Pressure Drop
50VQP
UNIT
SIZE
084
096
120
150
168
192
240
300
PRESSURE DROP (kPa)
L/s
0.66
1.00
1.32
0.76
1.13
1.51
0.95
1.42
1.89
1.20
1.76
2.39
1.32
1.98
2.65
1.51
2.27
1.89
2.84
3.78
2.39
3.53
4.79
3.78
–1 C
10 C
21 C
32 C
16.5
37.9
63.4
26.2
55.1
89.6
14.5
36.5
64.8
18.6
42.7
75.8
18.6
42.0
71.7
28.9
62.0
100.6
16.5
40.7
72.3
21.4
48.2
85.4
13.8
31.7
54.4
21.4
46.9
77.2
11.7
30.3
55.8
14.5
35.8
65.5
15.2
35.8
61.3
24.1
52.4
86.8
13.1
33.8
63.4
16.5
40.7
73.7
8.3
23.4
42.7
15.8
36.5
63.4
8.3
24.1
46.2
10.3
28.2
53.1
9.6
26.2
47.5
17.9
41.3
71.0
9.0
26.9
51.7
11.7
31.7
59.9
7.6
20.7
39.3
13.8
33.1
59.3
6.9
22.1
42.7
9.0
25.5
49.6
8.3
23.4
44.1
15.8
37.9
66.1
7.6
24.8
48.2
10.3
28.9
55.8
IMPORTANT: All alcohols should be pre-mixed and
pumped from a reservoir outside of the building or introduced under water level to prevent alcohols from fuming.
FREEZE PROTECTION SELECTION — The –1.1 C FP1
factory setting (water) should be used to avoid freeze damage
to the unit.
Once antifreeze is selected, the JW3 jumper (FP1) should
be clipped on the control to select the low temperature
(antifreeze –12.2 C) set point to avoid nuisance faults.
Table 18 — Approximate Fluid Volume (L)
per 30 M of Pipe
PIPE
Copper
Rubber Hose
Polyethylene
DIAMETER (in.) [mm] VOLUME (gal.) [L]
1 [25.4]
4.1 [15.5]
1.25 [31.8]
6.4 [24.2]
1.5 [38.1]
9.2 [34.8]
1 [25.4]
3.9 [14.8]
3/ IPS SDR11
2.8 [10.6]
4
1 IPS SDR11
4.5 [17.0]
11/4 IPS SDR11
8.0 [30.8]
1/ IPS SDR11
10.9 [41.3]
2
2 IPS SDR11
18.0 [68.1]
11/4 IPS SCH40
8.3 [31.4]
11/2 IPS SCH40
10.9 [41.3]
2 IPS SCH40
17.0 [64.4]
LEGEND
IPS — Internal Pipe Size
SCH — Schedule
SDR — Standard Dimensional Ratio
NOTE: If air is purged from the system while using a
250 mm PVC flush tank, only a 25 to 50 mm level drop will
be noticed since liquids are incompressible. If the level
drops more than this, flushing should continue since air is
still being compressed in the loop. If level is less than 25 to
50 mm, reverse the flow.
8. Repeat this procedure until all air is purged.
9. Restore power.
Antifreeze may be added before, during or after the
flushing process. However, depending on when it is added
in the process, it can be wasted. Refer to the Antifreeze section for more detail.
Loop static pressure will fluctuate with the seasons. Pressures will be higher in the winter months than during the
warmer months. This fluctuation is normal and should be
considered when charging the system initially. Run the unit
in either heating or cooling for several minutes to condition
the loop to a homogenous temperature.
When complete, perform a final flush and pressurize the
loop to a static pressure of 275 to 350 kPa for winter months
or 100 to 140 kPa for summer months.
After pressurization, be sure to remove the plug from the
end of the loop pump motor(s) to allow trapped air to be
discharged and to ensure the motor housing has been flooded. Be sure the loop flow center provides adequate flow
through the unit by checking pressure drop across the heat
exchanger.
NOTE: Volume of heat exchanger is approximately 3.78 liters.
Table 19 — Antifreeze Percentages by Volume
ANTIFREEZE
Methanol (%)
100% USP Food Grade
Propylene Glycol (%)
Ethanol (%)
MINIMUM TEMPERATURE FOR FREEZE
PROTECTION (C)
–12.2
–9.4
–6.7
–3.9
25
21
16
10
38
30
22
15
29
25
20
14
Cooling Tower/Boiler Systems — These systems
typically use a common loop maintained at 15.6 C to 32.2 C.
The use of a closed circuit evaporative cooling tower with a
secondary heat exchanger between the tower and the water
loop is recommended. If an open type cooling tower is
used continuously, chemical treatment and filtering will be
necessary.
Ground Coupled, Closed Loop and Plateframe
Heat Exchanger Well Systems — These systems
allow water temperatures from –1.1 to 43.3 C. The external
loop field is divided up into 51 mm polyethylene supply and
return lines. Each line has valves connected in such a way
that upon system start-up, each line can be isolated for flushing using only the system pumps. Air separation should be
located in the piping system prior to the fluid re-entering the
loop field.
Antifreeze — In areas where entering loop temperatures
drop below 4.4 C or where piping will be routed through areas subject to freezing, antifreeze is needed.
Alcohols and glycols are commonly used as antifreeze
agents. Freeze protection should be maintained to 8.3° C below
the lowest expected entering loop temperature. For example, if
the lowest expected entering loop temperature is –1.1 C, the
leaving loop temperature would be –5.6 to –3.9 C. Therefore,
the freeze protection should be at –9.4 C (–1.1 C – 8.3 C =
–9.4 C) Calculate the total volume of fluid in the piping system. See Table 18. Use the percentage by volume in
OPERATION
Power Up Mode — The unit will not operate until all
the inputs, terminals and safety controls are checked for
normal operation.
NOTE: The compressor will have a 5-minute anti-short
cycle upon power up.
36
Output EH2 will be off if FP1 is greater than 7.2 C and
FP2 (when shorted) is greater than 48.9 C during Heating
Stage 3 mode. This condition will have a 30-second
recognition time. Also, during Heating Stage 3 mode, EH1,
EH2, Fan Enable, and Fan Speed will be ON if G input is
not active.
EMERGENCY HEAT — In Emergency Heat mode, the
Fan Enable and Fan Speed relays are turned on. The EH1
output is turned on immediately. With continuing Emergency Heat demand, EH2 will turn on after 5 minutes. Fan Enable and Fan Speed relays are turned off after a 60-second
delay. The control reverts to Standby mode.
Output EH1, EH2, Fan Enable, and Fan Speed will be
ON if the G input is not active during Emergency Heat
mode.
COOLING STAGE 1 — In Cooling Stage 1 mode, the Fan
Enable, compressor and RV relays are turned on immediately. If configured as stage 2 (DIP switch set to OFF) then the
compressor and fan will not turn on until there is a stage 2
demand. The Fan Enable and compressor relays are turned
off immediately when the Cooling Stage 1 demand is removed. The control reverts to Standby mode. The RV relay
remains on until there is a heating demand. If there is a master/slave or dual compressor application, all compressor relays and related functions will track with their associated
DIP switch 2 on S1.
COOLING STAGE 2 — In Cooling Stage 2 mode, the Fan
Enable, compressor and RV relays remain on. The Fan
Speed relay is turned on immediately and turned off once
the Cooling Stage 2 demand is removed. The control reverts
to Cooling Stage 1 mode. If there is a master/slave or dual
compressor application, all compressor relays and related
functions will track with their associated DIP switch 2 on
S1.
NIGHT LOW LIMIT (NLL) STAGED HEATING — In
NLL staged Heating mode, the override (OVR) input becomes active and is recognized as a call for heating and the
control will immediately go into a Heating Stage 1 mode.
With an additional 30 minutes of NLL demand, the control
will go into Heating Stage 2 mode. With another additional
30 minutes of NLL demand, the control will go into Heating
Stage 3 mode.
Units with Aquazone™ Complete C Control
STANDBY — Y and W terminals are not active in Standby
mode, however the O and G terminals may be active, depending on the application. The compressor will be off.
COOLING — Y and O terminals are active in Cooling
mode. After power up, the first call to the compressor will
initiate a 5 to 80 second random start delay and a 5-minute
anti-short cycle protection time delay. After both delays are
complete, the compressor is energized.
NOTE: On all subsequent compressor calls the random start
delay is omitted.
HEATING STAGE 1 — Terminal Y is active in heating
stage 1. After power up, the first call to the compressor will
initiate a 5 to 80 second random start delay and a 5-minute
anti-short cycle protection time delay. After both delays are
complete, the compressor is energized.
NOTE: On all subsequent compressor calls the random start
delay is omitted.
HEATING STAGE 2 — To enter Stage 2 mode, terminal W
is active (Y is already active). Also, the G terminal must be
active or the W terminal is disregarded. The compressor relay will remain on and EH1 is immediately turned on. EH2
will turn on after 10 minutes of continual stage 2 demand.
NOTE: EH2 will not turn on (or if on, will turn off) if FP1
temperature is greater than 7.2 C and FP2 is greater than
48.9 C.
EMERGENCY HEAT — In emergency heat mode, terminal W is active while terminal Y is not. Terminal G must be
active or the W terminal is disregarded. EH1 is immediately
turned on. EH2 will turn on after 5 minutes of continual
emergency heat demand.
Units with Aquazone Deluxe D Control
STANDBY/FAN ONLY — The compressor will be off.
The Fan Enable, Fan Speed, and reversing valve (RV) relays
will be on if inputs are present. If there is a Fan 1 demand,
the Fan Enable will immediately turn on. If there is a Fan 2
demand, the Fan Enable and Fan Speed will immediately
turn on.
NOTE: DIP switch 5 on S1 does not have an effect upon
Fan 1 and Fan 2 outputs.
HEATING STAGE 1 — In Heating Stage 1 mode, the Fan
Enable and Compressor relays are turned on immediately.
Once the demand is removed, the relays are turned off and
the control reverts to Standby mode. If there is a master/
slave or dual compressor application, all compressor relays
and related functions will operate per their associated DIP
switch 2 setting on S1.
HEATING STAGE 2 — In Heating Stage 2 mode, the Fan
Enable and Compressor relays are remain on. The Fan
Speed relay is turned on immediately and turned off immediately once the demand is removed. The control reverts to
Heating Stage 1 mode. If there is a master/slave or dual
compressor application, all compressor relays and related
functions will operate per their associated DIP switch 2 setting on S1.
HEATING STAGE 3 — In Heating Stage 3 mode, the Fan
Enable, Fan Speed and Compressor relays remain on. The EH1
output is turned on immediately. With continuing Heat Stage 3
demand, EH2 will turn on after 10 minutes. EH1 and EH2 are
turned off immediately when the Heating Stage 3 demand is removed. The control reverts to Heating Stage 2 mode.
COMPLETE C AND DELUXE D BOARD
SYSTEM TEST
System testing provides the ability to check the control
operation. The control enters a 20-minute Test mode by momentarily shorting the test pins. All time delays are increased 15 times.
Test Mode — To enter Test mode on Complete C or De-
luxe D controls, cycle the power 3 times within 60 seconds.
The LED (light-emitting diode) will flash a code representing
the last fault when entering the Test mode. The alarm relay will
also power on and off during Test mode. See Tables 20-22. To
exit Test mode, short the terminals for 3 seconds or cycle the
power 3 times within 60 seconds.
NOTE: The Deluxe D control has a flashing code and alarm
relay cycling code that will both have the same numerical
label. For example, flashing code 1 will have an alarm relay
cycling code 1. Code 1 indicates the control has not faulted
since the last power off to power on sequence.
37
Table 20 — Complete C Control Current LED
Status and Alarm Relay Operations
LED STATUS
DESCRIPTION OF OPERATION
Normal Mode
On
Normal Mode with
PM Warning
Slow Flash
—
—
—
—
—
—
LED
CODE
1
FAULT
No fault in memory
Open
Over/Under Voltage Shutdown
Fast Flash
Lockout
Flashing Code 1 Test Mode — No fault in memory
Flashing Code 2 Test Mode — HP Fault in memory
Flashing Code 3 Test Mode — LP Fault in memory
Flashing Code 4 Test Mode — FP1 Fault in memory
Flashing Code 5 Test Mode — FP2 Fault in memory
Flashing Code 6 Test Mode — CO Fault in memory
Test Mode — Over/Under
Flashing Code 7
shutdown in memory
Flashing Code 8
Test Mode — PM in memory
Test Mode — FP1/FP2
Flashing Code 9
Swapped fault in memory
CO
FP
HP
LED
LP
PM
ALARM RELAY
Open
Cycle
(closed 5 sec.,
Open 25 sec.)
2
Complete C Control is
non-functional
Fault Retry
Off
Table 21 — Complete C Control LED Code and
Fault Descriptions
3
Open
Open
(Closed after
15 minutes)
Closed
Cycling Code 1
Cycling Code 2
Cycling Code 3
Cycling Code 4
Cycling Code 5
Cycling Code 6
4
5
6
7
(Autoreset)
8
Cycling Code 7
9
Cycling Code 8
Cycling Code 9
LEGEND
Condensate Overflow
Freeze Protection
High Pressure
Light-Emitting Diode
Low Pressure
Performance Monitor
FP
HP
LED
PM
—
—
—
—
DESCRIPTION
There has been no fault since the
last power-down to power-up
sequence
HP Open Instantly
High-Pressure
Switch
Low-Pressure Switch LP open for 30 continuous seconds
before or during a call (bypassed for
first 60 seconds)
Freeze Protection
FP1 below Temp limit for 30 continuCoax — FP1
ous seconds (bypassed for first 60
seconds of operation)
Freeze Protection Air FP2 below Temp limit for 30 continuCoil — FP2
ous seconds (bypassed for first 60
seconds of operation)
Condensate overflow Sense overflow (grounded) for 30
continuous seconds
Over/Under Voltage
"R" power supply is <19VAC or
Shutdown
>30VAC
PM Warning
Performance Monitor Warning has
occurred.
FP1 and FP2 Therm- FP1 temperature is higher than FP2
istors are swapped
in heating/test mode, or FP2 temperature is higher than FP1 in cooling/
test mode.
LEGEND
Freeze Protection
High Pressure
Light-Emitting Diode
Performance Monitor
NOTES:
1. Slow flash is 1 flash every 2 seconds.
2. Fast flash is 2 flashes every 1 second.
3. EXAMPLE: “Flashing Code 2” is represented by 2 fast flashes followed by
a 10-second pause. This sequence will repeat continually until the fault is
cleared.
Table 22 — Aquazone™ Deluxe D Control Current LED Status and Alarm Relay Operations
TEST LED
(Yellow)
Off
FAULT LED (Red)
ALARM RELAY
Normal Mode
STATUS LED
(Green)
On
Flash Last Fault Code in Memory
Normal Mode with PM
On
Off
Flashing Code 8
Open
Cycle (closed 5 sec,
open 25 sec, …)
Off
Off
Off
Open
—
Flashing Code 2
Flashing Code 3
Flashing Code 4
On
Slow Flash
Slow Flash
Slow Flash
Slow Flash
Slow Flash
Slow Flash
Fast Flash
Fast Flash
Fast Flash
Fast Flash
Fast Flash
On
—
—
—
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Flash Last Fault Code in Memory
Flash Last Fault Code in Memory
Flash Last Fault Code in Memory
Flash Last Fault Code in Memory
Flashing Code 1
Flashing Code 2
Flashing Code 3
Flashing Code 4
Flashing Code 5
Flashing Code 6
Flashing Code 7
Flashing Code 2
Flashing Code 3
Flashing Code 4
Flashing Code 5
Flashing Code 6
Cycling Appropriate Code
—
—
—
Open
Open
Open
Open
Open
Open
Open (closed after 15 minutes)
Closed
Closed
Closed
Closed
Closed
DESCRIPTION
Deluxe D Control is
non-functional
Test Mode
Night Setback
ESD
Invalid T-stat Inputs
No Fault in Memory
HP Fault
LP Fault
FP1 Fault
FP2 Fault
CO Fault
Over/Under Voltage
HP Lockout
LP Lockout
FP1 Lockout
FP2 Lockout
CO Lockout
CO
ESD
FP
HP
LP
PM
—
—
—
—
—
—
LEGEND
Condensate Overflow
Emergency Shutdown
Freeze Protection
High Pressure
Low Pressure
Performance Monitor
NOTES:
1. If there is no fault in memory, the Fault LED will flash code 1.
2. Codes will be displayed with a 10-second Fault LED pause.
3. Slow flash is 1 flash every 2 seconds.
4. Fast flash is 2 flashes every 1 second.
5. EXAMPLE: “Flashing Code 2” is represented by 2 fast flashes followed by
a 10-second pause. This sequence will repeat continually until the fault is
cleared.
38
Retry Mode — In Retry mode, the status LED will start to
IMPORTANT: To avoid fouled machinery and extensive
unit clean-up, DO NOT operate units without filters in
place. DO NOT use equipment as a temporary heat source
during construction.
flash slowly to signal that the control is trying to recover from
an input fault. The control will stage off the outputs and try to
again satisfy the thermostat used to terminal Y. Once the thermostat input calls are satisfied, the control will continue normal
operation.
NOTE: If 3 consecutive faults occur without satisfying the
thermostat input call to terminal Y, the control will go into
lockout mode. The last fault causing the lockout is stored in
memory and can be viewed by entering Test mode.
Condensate Drain Pans — Check condensate drain
pans for algae growth twice a year. If algae growth is apparent,
consult a water treatment specialist for proper chemical treatment. The application of an algaecide every three months will
typically eliminate algae problems in most locations.
Aquazone™ Deluxe D Control LED Indicators — There are 3 LED indicators on the Deluxe D control:
Refrigerant System — Verify air and water flow rates
are at proper levels before servicing. To maintain sealed circuitry integrity, do not install service gages unless unit operation
appears abnormal.
STATUS LED — Status LED indicates the current status or
mode of the Deluxe D control. The Status LED light is green.
TEST LED — Test LED will be activated any time the Deluxe D control is in Test mode. The Test LED light is yellow.
FAULT LED — Fault LED light is red. The fault LED will
always flash a code representing the last fault in memory. If
there is no fault in memory, the fault LED will flash code 1 and
appear as 1 fast flash alternating with a 10-second pause. See
Table 22.
Condensate Drain Cleaning — Clean the drain line
and unit drain pan at the start of each cooling season. Check
flow by pouring water into drain. Be sure trap is filled to maintain an air seal.
Air Coil Cleaning — Remove dirt and debris from evaporator coil as required by condition of the coil. Clean coil with
a stiff brush, vacuum cleaner, or compressed air. Use a fin
comb of the correct tooth spacing when straightening mashed
or bent coil fins.
SERVICE
Perform the procedures outlined below periodically, as
indicated.
Condenser Cleaning — Water-cooled condensers may
require cleaning of scale (water deposits) due to improperly
maintained closed-loop water systems. Sludge build-up may
need to be cleaned in an open water tower system due to
induced contaminants.
Local water conditions may cause excessive fouling or
pitting of tubes. Condenser tubes should therefore be cleaned at
least once a year, or more often if the water is contaminated.
Proper water treatment can minimize tube fouling and
pitting. If such conditions are anticipated, water treatment
analysis is recommended. Refer to the Carrier System Design
Manual, Part 5, for general water conditioning information.
IMPORTANT: When a compressor is removed from this
unit, system refrigerant circuit oil will remain in the compressor. To avoid leakage of compressor oil, the refrigerant
lines of the compressor must be sealed after it is removed.
IMPORTANT: All refrigerant discharged from this unit
must be recovered without exception. Technicians must follow industry accepted guidelines and all local, state and federal statutes for the recovery and disposal of refrigerants.
IMPORTANT: To avoid the release of refrigerant into the
atmosphere, the refrigerant circuit of this unit must only be
serviced by technicians which meet local, state and federal
proficiency requirements.
CAUTION
Follow all safety codes. Wear safety glasses and rubber
gloves when using inhibited hydrochloric acid solution.
Observe and follow acid manufacturer’s instructions. Failure to follow these safety precautions could result in personal injury or equipment or property damage.
IMPORTANT: To prevent injury or death due to electrical
shock or contact with moving parts, open unit disconnect
switch before servicing unit.
Clean condensers with an inhibited hydrochloric acid solution. The acid can stain hands and clothing, damage concrete,
and, without inhibitor, damage steel. Cover surroundings to
guard against splashing. Vapors from vent pipe are not harmful,
but take care to prevent liquid from being carried over by the
gases.
Warm solution acts faster, but cold solution is just as effective if applied for a longer period.
GRAVITY FLOW METHOD — Do not add solution faster
than vent can exhaust the generated gases.
When condenser is full, allow solution to remain overnight,
then drain condenser and flush with clean water. Follow acid
manufacturer’s instructions. See Fig. 36.
FORCED CIRCULATION METHOD — Fully open vent
pipe when filling condenser. The vent may be closed when
condenser is full and pump is operating. See Fig. 37.
Regulate flow to condenser with a supply line valve. If
pump is a nonoverloading type, the valve may be fully closed
while pump is running.
For average scale deposit, allow solution to remain in condenser overnight. For heavy scale deposit, allow 24 hours.
Filters — Filters must be clean for maximum performance.
Inspect filters every month under normal operating conditions.
replace when necessary.
IMPORTANT: Units should never be operated without a filter.
Water Coil — Keep all air out of the water coil. Check
open loop systems to be sure the well head is not allowing air
to infiltrate the water line. Always keep lines airtight.
Inspect heat exchangers regularly, and clean more frequently if the unit is located in a “dirty” environment. The heat
exchanger should be kept full of water at all times. Open loop
systems should have an inverted P trap placed in the discharge
line to keep water in the heat exchanger during off cycles.
Closed loop systems must have a minimum of 100 kPa during
the summer and 275 kPa during the winter.
Check P trap frequently for proper operation.
39
Refrigerant Charging
FILL CONDENSER WITH
CLEANING SOLUTION. DO
NOT ADD SOLUTION
MORE RAPIDLY THAN
VENT CAN EXHAUST
GASES CAUSED BY
CHEMICAL ACTION.
WARNING
PAIL
To prevent personal injury, wear safety glasses and gloves
when handling refrigerant. Do not overcharge system —
this can cause compressor flooding.
FUNNEL
NOTE: Do not vent or depressurize unit refrigerant to atmosphere. Remove and recover refrigerant following accepted
practices.
1-IN.
(25 mm)
PIPE
VENT
PIPE
1.5 m APPROX
Air Coil Fan Motor Removal
1.0 TO 1.2 m
CONDENSER
CAUTION
Before attempting to remove fan motors or motor mounts,
place a piece of plywood over evaporator coils to prevent
coil damage.
Motor power wires need to be disconnected from motor
terminals before motor is removed from unit.
1. Shut off unit main power supply.
2. Loosen bolts on mounting bracket so that fan belt can be
removed.
3. Loosen and remove the 2 motor mounting bracket bolts
on left side of bracket.
4. Slide motor/bracket assembly to extreme right and lift out
through space between fan scroll and side frame. Rest
motor on a high platform such as a step ladder. Do not
allow motor to hang by its power wires.
PAIL
Fig. 36 — Gravity Flow Method
PUMP
PRIMING
CONN.
a50-8586
GAS VENT
GLOBE
VALVES
SUCTION
SUPPLY
PUMP
SUPPORT
1-IN.
(25 mm)
PIPE
TANK
TROUBLESHOOTING
When troubleshooting problems with a WSHP, see
Table 23.
CONDENSER
Thermistor — A thermistor may be required for singlephase units where starting the unit is a problem due to low
voltage. See Fig. 38 for thermistor nominal resistance.
REMOVE WATER
REGULATING VALVE
FINE MESH
SCREEN
90.0
RETURN
80.0
Fig. 37 — Forced Circulation Method
70.0
Resistance (kOhm)
Drain condenser and flush with clean water. Follow acid
manufacturer’s instructions.
Checking System Charge — Units are shipped with
full operating charge. If recharging is necessary:
1. Insert thermometer bulb in insulating rubber sleeve on
liquid line near filter drier. Use a digital thermometer for
all temperature measurements. DO NOT use a mercury
or dial-type thermometer.
2. Connect pressure gage to discharge line near compressor.
3. After unit conditions have stabilized, read head pressure
on discharge line gage.
NOTE: Operate unit a minimum of 15 minutes before
checking charge.
4. From standard field-supplied Pressure-Temperature chart
for R-410A, find equivalent saturated condensing
temperature.
5. Read liquid line temperature on thermometer; then
subtract from saturated condensing temperature. The difference equals subcooling temperature.
60.0
50.0
40.0
30.0
20.0
10.0
0.0
-17.7
-6.6
4.4
15.6
26.7
37.8
48.9
60.0
Temperature (C)
Fig. 38 — Thermistor Nominal Resistance
Control Sensors — The control system employs 2 nom-
inal 10,000 ohm thermistors (FP1 and FP2) that are used for
freeze protection. Be sure FP1 is located in the discharge fluid
and FP2 is located in the air discharge. See Fig. 39.
40
AIRFLOW
(°C)
AIR
COIL
SUCTION
AIRFLOW
(°C)
COMPRESSOR
THERMISTOR
EXPANSION
VALVE
FP2
COAX
DISCHARGE
FP1
CONDENSATE
OVERFLOW
(CO)
LIQUID
LINE
AIR COIL
FREEZE
PROTECTION
WATER IN
WATER
COIL
PROTECTION
WATER OUT
LEGEND
COAX — Coaxial Heat Exchanger
Airflow
Refrigerant Liquid Line Flow
a50-8163
Fig. 39 — FP1 and FP2 Thermistor Location
41
Table 23 — Troubleshooting
FAULT
Main Power Problems
HEATING COOLING
POSSIBLE CAUSE
X
X
Green Status LED Off
HP Fault — Code 2
High Pressure
X
X
X
X
LP Fault — Code 3
Low Pressure/Loss of
Charge
FP1 Fault — Code 4
Water Freeze Protection
X
X
X
X
X
X
X
X
X
X
X
X
FP2 Fault — Code 5
Air Coil Freeze
Protection
X
X
X
X
Condensate Fault —
Code 6
Over/Under Voltage —
Code 7
(Auto Resetting)
X
X
X
X
X
X
X
X
Performance Monitor —
Code 8
X
No Fault Code Shown
X
X
X
X
X
X
X
X
X
X
Unit Short Cycles
Only Fan Runs
FP
HP
LED
LP
RV
—
—
—
—
—
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SOLUTION
Check line voltage circuit breaker and disconnect.
Check for line voltage between L1 and L2 on the contactor.
Check for 24-vac between R and C on controller.
Check primary/secondary voltage on transformer.
Reduced or no water flow in Check pump operation or valve operation/setting.
cooling
Check water flow adjust to proper flow rate.
Water temperature out of
Bring water temperature within design parameters.
range in cooling
Reduced or no airflow in
Check for dirty air filter and clean or replace.
heating
Check fan motor operation and airflow restrictions.
Dirty air coil — construction dust, etc. Perform preventative maintenance; Clean air coil.
High external static. Check duct design and downstream interference.
Air temperature out of range Bring return-air temperature within design parameters.
in heating
Overcharged with refrigerant Check superheat/subcooling vs. typical operating condition.
Bad HP switch
Check switch continuity and operation. Replace.
Insufficient charge
Check for refrigerant leaks.
Compressor pump down at Check charge and start-up water flow.
start-up
Reduced or no water flow in Check pump operation or water valve operation/setting.
heating
Plugged strainer or filter. Clean or replace.
Check water flow adjust to proper flow rate.
Inadequate antifreeze level Check antifreeze density with hydrometer.
Improper freeze protect set- Clip JW3 jumper for antifreeze (–12.2 C) use.
ting (–1.1 Cvs –12.2 C)
Water temperature out of
Bring water temperature within design parameters.
range
Bad thermistor
Check temperature and impedance correlation.
Reduced or no airflow in
Check for dirty air filter and clean or replace.
cooling
Check fan motor operation and airflow restrictions.
High external static. Check duct design and downstream interference.
Air temperature out of range Too much cold vent air. Bring entering-air temperature within design
parameters.
Improper freeze protect set- Normal airside applications will require –1.1 C only.
ting (–1.1 Cvs –12.2 C)
Bad thermistor
Check temperature and impedance correlation.
Blocked drain
Check for blockage and clean drain.
Improper trap
Check trap dimensions and location ahead of vent.
Poor drainage
Check for piping slope away from unit.
Check slope of unit toward outlet.
Poor venting. Check vent location.
Moisture on sensor
Check for moisture shorting to air coil.
Under voltage
Check power supply and 24-vac voltage before and during operation.
Check power supply wire size.
Check compressor starting.
Check 24-vac and unit transformer tap for correct power supply voltage.
Over voltage
Check power supply voltage and 24 vac before and during operation.
Check 24-vac and unit transformer tap for correct power supply voltage.
Heating mode FP2> 51.7 C Check for poor airflow or overcharged unit.
Cooling mode FP1> 51.7 C Check for poor water flow or airflow.
OR FP2< 4.4 C
Compressor overload
Check and replace if necessary.
Control board
Reset power and check operation.
Dirty air filter
Check and clean air filter.
Unit in Test mode
Reset power or wait 20 minutes for auto exit.
Unit selection
Unit may be oversized for space. Check sizing for actual load of space.
Compressor overload
Check and replace if necessary.
Thermostat position
Ensure thermostat set for heating or cooling operation.
Unit locked out
Check for lockout codes. Reset power.
Compressor overload
Check compressor overload. Replace if necessary.
Thermostat wiring
Check Y and W wiring at heat pump. Jumper Y and R for compressor
operation in Test mode.
LEGEND
Freeze Protection
High Pressure
Light-Emitting Diode
Low Pressure
Reversing Valve
42
Table 23 — Troubleshooting (cont)
FAULT
Only Compressor Runs
HEATING COOLING
POSSIBLE CAUSE
X
X
Thermostat wiring
X
X
Fan motor relay
X
X
X
Fan motor
Reversing valve
X
X
X
Thermostat setup
Thermostat wiring
Dirty filter
Reduced or no airflow in
heating
X
Reduced or no airflow in
cooling
X
X
Leaky ductwork
X
X
X
X
X
X
X
X
X
Low refrigerant charge
Restricted metering device
Defective reversing valve
Thermostat improperly
located
Unit undersized
X
X
X
X
X
Unit Does Not Operate in
Cooling
Insufficient Capacity/
Not Cooling or Heating
Properly
High Head Pressure
X
X
X
X
X
X
Low Suction Pressure
X
X
X
X
X
X
X
X
X
X
Low Discharge Air
Temperature in Heating
High Humidity
FP
HP
LED
LP
RV
—
—
—
—
—
X
X
X
X
X
X
Scaling in water heat
exchanger
Inlet water too hot or cold
Reduced or no airflow in
heating
SOLUTION
Check G wiring at heat pump. Jumper G and R for fan operation.
Check Y and W wiring at heat pump. Jumper Y and R for compressor
operation in Test mode.
Jumper G and R for fan operation. Check for line voltage across BR
contacts.
Check fan power enable relay operation (if present).
Check for line voltage at motor. Check capacitor.
Set for cooling demand and check 24-vac on RV coil and at control.
If RV is stuck, run high pressure up by reducing water flow and while
operating engage and disengage RV coil voltage to push valve.
Check for ‘O’ RV setup not ‘B’.
Check O wiring at heat pump. Jumper O and R for RV coil.
Replace or clean.
Check for dirty air filter and clean or replace.
Check fan motor operation and airflow restrictions.
High external static. Check duct design and downstream interference.
Check for dirty air filter and clean or replace.
Check fan motor operation and airflow restrictions.
High external static. Check duct design and downstream interference.
Check supply and return-air temperatures at the unit and at distant
duct registers if significantly different, duct leaks are present.
Check superheat and subcooling.
Check superheat and subcooling. Replace.
Perform RV touch test.
Check location and for air drafts behind thermostat.
Recheck loads and sizing check sensible cooling load and heat pump
capacity.
Perform scaling check and clean if necessary.
Check load, loop sizing, loop backfill, ground moisture.
Check for dirty air filter and clean or replace.
Check fan motor operation and airflow restrictions.
High external static. Check duct design and downstream interference.
Reduced or no water flow in Check pump operation or valve operation/setting.
cooling
Check water flow adjust to proper flow rate.
Inlet water too hot
Check load, loop sizing, loop backfill, ground moisture.
Air temperature out of range Bring return-air temperature within design parameters.
in heating
Scaling in water heat
Perform scaling check and clean if necessary.
exchanger
Unit overcharged
Check superheat and subcooling. Reweigh in charge.
Non-condensables in
Vacuum system and reweigh in charge.
system
Restricted metering device Check superheat and subcooling. Replace.
Reduced water flow in
Check pump operation or water valve operation/setting.
heating
Plugged strainer or filter. Clean or replace.
Check water flow adjust to proper flow rate.
Water temperature out of
Bring water temperature within design parameters.
range
Reduced airflow in cooling Check for dirty air filter and clean or replace.
Check fan motor operation and airflow restrictions.
High external static. Check duct design and downstream interference.
Air temperature out of range Too much cold vent air. Bring entering air temperature within design
parameters.
Insufficient charge
Check for refrigerant leaks.
Too high airflow
Check blower.
Poor performance
See ‘Insufficient Capacity’ above.
Too high airflow
Check blower.
Unit oversized
Recheck loads and sizing check sensible cooling load and heat pump
capacity.
LEGEND
Freeze Protection
High Pressure
Light-Emitting Diode
Low Pressure
Reversing Valve
43
Copyright 2010 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53500080-01
Printed in U.S.A.
Form 50VQP-C1SI
Pg 46
11-10
Replaces: New
50VQP
START-UP CHECKLIST
CUSTOMER:___________________________
JOB NAME: _______________________________________
MODEL NO.:___________________________
SERIAL NO.:____________________
DATE:_________
I. PRE-START-UP
DOES THE UNIT VOLTAGE CORRESPOND WITH THE SUPPLY VOLTAGE AVAILABLE? (Y/N)
HAVE THE POWER AND CONTROL WIRING CONNECTIONS BEEN MADE AND TERMINALS
TIGHT? (Y/N)
HAVE WATER CONNECTIONS BEEN MADE AND IS FLUID AVAILABLE AT HEAT EXCHANGER?
(Y/N)
HAS PUMP BEEN TURNED ON AND ARE ISOLATION VALVES OPEN? (Y/N)
HAS CONDENSATE CONNECTION BEEN MADE AND IS A TRAP INSTALLED? (Y/N)
IS AN AIR FILTER INSTALLED? (Y/N)
II. START-UP
IS FAN OPERATING WHEN COMPRESSOR OPERATES? (Y/N)
IF 3-PHASE SCROLL COMPRESSOR IS PRESENT, VERIFY PROPER ROTATION PER INSTRUCTIONS.
(Y/N)
UNIT VOLTAGE — COOLING OPERATION
PHASE AB VOLTS
PHASE BC VOLTS
(if 3 phase)
PHASE CA VOLTS
(if 3 phase)
PHASE AB AMPS
PHASE BC AMPS
(if 3 phase)
PHASE CA AMPS
(if 3 phase)
CONTROL VOLTAGE
IS CONTROL VOLTAGE ABOVE 21.6 VOLTS? (Y/N)
.
IF NOT, CHECK FOR PROPER TRANSFORMER CONNECTION.
TEMPERATURES
FILL IN THE ANALYSIS CHART ATTACHED.
COAXIAL HEAT COOLING CYCLE:
EXCHANGER
FLUID IN
C FLUID OUT
C
kPa
L/s
HEATING CYCLE:
FLUID IN
C FLUID OUT
C
kPa
L/s
COOLING CYCLE:
AIR IN
C
AIR OUT
C
HEATING CYCLE:
AIR IN
C
AIR OUT
C
AIR COIL
Book
Tab
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
1 1 1 4 4 4
CL-1 in U.S.A.
PC 111
Catalog No. 536-203
Printed
Form 62AQ-1SI
Pg CL-1
7-99
Replaces: New
1a 1b 5a 5a 6a 6b
kPa
DEW
POINT
°C
AIR
COIL
SUCTION
°C
°C
COMPRESSOR
EXPANSION
VALVE
COAX
DISCHARGE
°C
°C
LIQUID LINE
kPa
WATER IN
°C
kPa
WATER OUT
LOOK
UPUP
PRESSURE
DROP
IN IN
TABLE
17 8
LOOK
PRESSURE
DROP
TABLE
TOTO
DETERMINE
FLOW
RATE
DETERMINE
FLOW
RATE
COOLING CYCLE ANALYSIS
kPa
DEW
POINT
°C
AIR
COIL
°C
SUCTION
°C
COMPRESSOR
EXPANSION
VALVE
COAX
DISCHARGE
°C
LIQUID LINE
°C
kPa
WATER IN
°C
kPa
WATER OUT
LOOK
LOOKUP
UPPRESSURE
PRESSUREDROP
DROPIN
INTABLE
TABLE17
8
TO
TODETERMINE
DETERMINEFLOW
FLOWRATE
RATE
HEAT OF EXTRACTION (ABSORPTION) OR HEAT OF REJECTION =
FLOW RATE (L/s) x
TEMP. DIFF. (DEG. C) x
FLUID FACTOR* =
(kW)
SUPERHEAT = SUCTION TEMPERATURE – SUCTION SATURATION TEMPERATURE
=
(DEG C)
SUBCOOLING = DISCHARGE SATURATION TEMPERATURE – LIQUID LINE TEMPERATURE
=
(DEG C)
*Use 500 for water, 485 for antifreeze.
Copyright 2010 Carrier Corporation
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53500080-01
Printed in U.S.A.
Form 50VQP-C1SI
Pg CL-2
11-10
Replaces: New
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - CUT ALONG DOTTED LINE
CUT ALONG DOTTED LINE
HEATING CYCLE ANALYSIS