Advent 128-8567 Installation guide

ADV10
10.2” OVERHEAD LCD
MONITOR WITH
DVD PLAYER
OPERATION
MANUAL
R
128-8567
Important Notice
Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side
curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or
D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from
fully deploying which can result in personal injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle,
please contact Audiovox Technical Support at 1-800-225-6074.
When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to
the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection
point and the mobile video product.
An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used
for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television
reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is
in “park” or when the vehicle's parking brake is applied.
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the
parking brake is not applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator
of the motor vehicle.
Warnings
• Do not use any solvents or cleaning materials when cleaning the video monitor.
• Do not use any abrasive cleaners, they may scratch the screen.
• Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.
• Lock the LCD screen in the fully closed position when not in use.
• Before putting on headphones always adjust the volume setting to the lowest position.
• Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left on, can drain
the vehicle's battery.
• Do not put pressure on the screen.
• Caution children to avoid touching or scratching the screen, as it may become dirty or damaged.
Licensed under one or more of the following patents,
Patent NOS. 5,775,762 , 5,927,784 and 6,678,892
FEATURES
Congratulations
Congratulations on your purchase of the ADVENT ADV10
DVD Player with drop-down video / monitor. The ADV10 has
been designed to give you and your family many years of
video entertainment in the mobile environment. Please read
the directions that follow to familiarize yourself with the
product to ensure that you obtain the best results from your
equipment.
•
10.2” TFT (Thin Film Transistor) Active Matrix LCD
(Liquid Crystal Display) Monitor
•
Built-in DVD Player
•
OSD (On Screen Display) for Control of Picture Quality
and Functions
•
Infrared Transmitter for IR wireless headphones
Note: Installation options vary, see the individual owner's
manuals for each component in your system to obtain a full
understanding of each component's operation.
•
Two Audio / Video Source Inputs (DVD, AV1/AUX)
•
Dome lights with built-in three way switch
•
Built-in 16 Channel Wireless FM Modulator
Safety Precaution
•
Last Position Memory for DVD
•
Screen Mode selection (4:3, 16:9)
•
Full Function Remote Control
•
Backlit Controls
•
AV output via RCA Jacks
•
Playing DVD, CD and MP3 discs
For safety reasons, when changing video media it is
recommended that the vehicle is not in motion, and that you
do not allow children to unfasten seat-belts to change video
media or make any adjustments to the system. System
adjustments can be accomplished using the remote control,
while seat-belts remain fastened. Enjoy your ADVENT
entertainment system but remember the safety of all
passengers remains the number one priority.
3
CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW)
1
4. STOP (n) Control
- Press STOP once : Stops playback,
Pressing the PLAY button again will resume normal
playback from where movie was stopped.
- Press STOP twice and then press PLAY to start playback
from the beginning of the DVD.
2
3
4
5
6
7
5. EJECT () Control
This control is used for ejecting disc from the disc
compartment.
8
6. Three Position Dome Light Switch
ON - Turns on the dome lights.
OFF - The dome lights will not turn on in this position.
AUTO - Automatically switches on the dome lights in
conjunction with the vehicle's interior illumination.
9
7. Dome Lights
Provide additional interior illumination.
10
8. Ventilation Openings
9. LCD Cut Off Switch
Used to turn off the LCD backlight when the LCD is in the
closed position.
11
1. POWER ( ) Control
Used to turn the system on/off (standby).
10. LCD Panel
11. Screen Release
Press to release the screen.
2. Source Select (S)
Use to select one of the two sources: DVD, AV1/AUX
3. PLAY (u) Control
This control is used to start playback of a disc.
4
CONTROL FUNCTION DESCRIPTION (SIDE VIEW)
1
1. DVD Disc insertion Slot
For loading and removing discs.
CONTROL FUNCTION DESCRIPTION (BACK VIEW)
1 23
1. Auxiliary Video Input
2. Auxiliary Audio Left Input
3. Auxiliary Audio Right Input
5
REMOTE CONTROL OPERATION
MAIN FUNCTION OPERATION
POWER
1
2
3
4
M2
TV
DVD
30
SOURCE
DVD SOURCE
5
6
CR2025
EJECT
M1
MUTE
VOLUME
27
PIX
SYSTEM MENU
DISC MENU
7
8
ZOOM
REPEAT
Initial Use
When purchased the remote control has a battery installed with a
Pull Tab to prevent battery discharge. Remove the Pull Tab before
attempting to use the remote.
DISPLAY
SETUP
SUBTITLE
10
AUDIO
Battery Replacement
1. Remove the battery holder.
2. Insert the battery into the battery holder and insert the battery
holder into the remote. Be sure to observe the correct polarity.
3. Align the battery holder with the remote control and push it in
until the holder clicks.
26
25
24
ENTER
9
29
28
23
22
11
12
21
20
13
14
19
18
1
2
3
4
5
6
7
8
FMM
ON/OFF
9
0
IRT
ON/OFF
15
16
6
17
* Function control is available on the unit and the Remote Control.
** Function not available in this model.
1. POWER*
Press this button to turn the unit ON and OFF.
2.
MONITOR SELECT
M1 Button – Set the remote control code to allow control of the unit in M1 mode.
M2 Button** – Set the remote control code to allow control of the unit in M2 mode.
3.
SOURCE*
Each time the button is pressed, the unit will cycle through modes DVD, AV1/AUX
4.
TV Mode Select
Switches certain function keys on the remote control for monitor functions.
5.
DVD Source
This button is only active when remote control is in DVD mode.
6. PIX ( Picture Select )
Each time of this button is pressed, the OSD picture adjustment displays the “Adjustment bar” for BRIGHTNESS, CONTRAST,
COLOR, TINT(For NTSC only) or RESET. Once the desired adjustment bar is displayed, use the VOLUME+/ –VOLUME– button to
adjust the setting. The display will automatically turn off if no adjustments are made within 6 seconds.
7.
SYSTEM MENU
Allow the user to access the system menu when the unit has been placed in TV mode ( See Item number 4 ). Press cursor (pq) buttons to select
desired picture control FMM screen mode, OSD language and source default during power up.
8.
CURSOR (pqtu)
Use these buttons to access menu selections on the screen.
7
9. ENTER
Used to implement a selected setting or menu option.
10. DISPLAY
Press to display the current disc information while the disc is playing. Press the cursor (pq) buttons to select the Title or Chapter. For
Title/Chapter selection use the numeric buttons to enter the desired Title /Chapter selection.
11. SCAN BACKWARD (7)
Press to search in a backward direction. Press repeatedly to change the search speed from 2, 4, 8, 16 times and normal speed.
12. PLAY*
Press to activate the play mode while a disc is loaded into the disc compartment.
13. PREVIOUS (9)
Press to return to the previous chapter or track.
14. PAUSE (II)
Press to pause playback.
15. NUMBERS
Allow the user to ENTER the numbers 0-9 for selection of the tracks, titles chapters or password setting.
16. FMM ON/OFF
Turns the FM Modulator power on/off.
17. IRT ON/OFF (Optional)
Turns the Infrared Transmitter on or off for IR wireless headphones.
18. NEXT (:)
Press to skip to the next chapter or track.
8
19. STOP (<)*
Press to stop playback.(Playback will resume from the point it is stopped).
Press twice at once to stop playback fully. (Playback will resume from the beginning of the disc).
20. SCAN FORWARD (8)
Press to search in a forward direction. Press repeatedly to change the search speed from 2, 4, 8, 16 times and normal speed.
21. AUDIO
Press to display and select audio language in DVD mode. Each time you press the button, the language changes.
Note: The available languages vary from disc to disc.
22. SETUP
Press to display the Setup menu which allows the user to change the DVD player options such as LANGUAGE, VIDEO, RATING &
MISC.
Note: The unit must be set to DVD mode by pressing the DVD button prior to pressing the SETUP button.
23. SUBTITLE
Press to display and select the subtitle language in DVD mode. Each time you press the button, the subtitle language changes.
Note: The type and number of languages for subtitle vary from disc to disc.
24. REPEAT
Allows the user to repeat a selected title, chapter, or track.
25. DISC MENU
Allow the user to access the disc’s menu mode.
9
26. ZOOM
Press this button to enlarge the picture when playing a DVD disc.
Press ZOOM button
DVD player perform
Once
Q1- Enlarge the picture 2 times of the original size
Second
Q2- Enlarge the picture 3 times of the original size
Third
Q3- Enlarge the picture 4 times of the original size
Forth
Q off- Picture is returned to original size
27. VOLUME DOWN (-) or UP (+)
Press to decrease or increase the level of the picture adjustments after the picture select button (PIX) is pressed.
28. DVD Mode Select Button
Switches certain function keys on the remote control for DVD function.
29. MUTE
Press this button to mute the audio for wireless FMM, IR headphones and wired headphones.
Pressing the button again restores the audio to the previously set level.
30. EJECT ()*
This button is used to eject the disc.
10
SYSTEM MENU ADJUSTMENTS
The System Menu Contains features and options that let you customize your system to change the screen mode display, OSD language
and source default.
1)
2)
3)
4)
5)
Press the TV button and then the SYSTEM MENU button on the remote, the main page of the system menu will appear on screen.
Use the cursor buttons p or q to select the desired item in the main page and press the ENTER button to select.
The submenu will appear on screen.
Use the cursor buttons p or q to select an item in the sub menu and then press the ENTER button to select.
Press the System Menu button to exit System Menu.
Note: System Menu can be controlled via Remote Control only. (Items selected in the menu will have a green background)
PICTURE CONTROL SELECT
When watching a program, the picture quality can be adjusted to the user’s references.
1) Press the SYSTEM MENU button on the remote and the on screen picture adjustment displays the “adjustment” for BRIGHTNESS,
CONTRAST, COLOR, TINT (for NTSC only) or RESET.
2) Use the cursor buttons p or q to highlight PICTURE CONTROL and press ENTER. The PICTURE CONTROL menu will be displayed.
3) Use the cursor buttons p or q to select the desired adjustment and press ENTER.
4) Use the cursor buttons p or q or the +or - buttons to change the settings. Press ENTER when the adjustment is finished.
SYSTEM MENU
PICTURE CONTROL
FMM
PICTURE CONTROL
BRIGHTNESS
CONTRAST
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
COLOR
TINT
RESET
11
FMM SELECT
FMM ON/OFF options - Turns the wireless FM Modulator on or off.
FMM SELECT option - Selects the wireless FM Modulator Frequency (CH1 88.1MHz, CH2 88.3MHz, CH3 88.5MHz, CH4 88.7MHz, CH5
88.9MHz, CH6 89.1MHz, CH7 89.3MHz, CH8 89.5MHz, CH9 89.7MHz, CH10 89.9MHz, CH11 90.1MHz, CH12
90.3MHz, CH13 90.5MHz, CH14 90.7MHz, Ch15 90.9MHz, CH16 91.1MHz)
SYSTEM MENU
PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
FMM
FMM ON
FMM OFF
FMM SELECT
OSD LANGUAGE
This function allows the user to select the language for the on-screen display.
The user can either select English, Spanish, French or German for the OSD language.
SYSTEM MENU
PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
OSD LANGUAGE
ENGLISH
SPANISH
FRENCH
GERMAN
12
SOURCE DEFAULT DVD
This allows the user to set the system default source to DVD.
Note:
• If source default is set to ON, every time the unit is turned off then on, the unit will power up and automatically switch the source to DVD. If
source default is set to OFF and the unit is turned off then on, the unit will power up in whatever source was last selected.
• Unit is set to source default DVD on as the default mode of operation.
• Selection of Source default can only be made from within the system menu.
SYSTEM MENU
PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
SOURCE DEFAULT DVD
ON
OFF
SCREEN MODE SELECT
This allows the user to change the screen format (aspect ratio 4:3, 16:9).
To select the screen aspect ratio format highlight SCREEN MODE and press ENTER button to access the submenu. Then press the
Cursor button p or q to select from 4:3 or 16:9. Press ENTER button to confirm the setting.
SYSTEM MENU
PICTURE CONTROL
FMM
OSD LANGUAGE
SOURCE DEFAULT DVD
SCREEN MODE
SCREEN MODE
4:3
16:9
13
DVD SETTINGS AND ADJUSTMENTS
The DVD Setup Menu contains features and options that let you customize your DVD player. For example, you can set a language for the
on-screen display or prevent children from viewing DVD playback of adult DVD Titles.
Using the Setup Menu
1. Press the DVD button and then the SETUP button on the remote. The Setup Menu appears on the
screen as shown per diagram.
2. Use the p or q cursor buttons to highlight the settings to be changed. Use the u cursor button to
highlight the sub-setttings. Press u cursor button to open the submenu that contains the different
options available. Press the ENTER button to set the desired option.
3. Use t cursor button to position the highlight back on the icon side of the setup page to set the other
options. Repeat steps 1~2.
Exiting the Setup Menu
Press the SETUP button again.
LANGUAGE SETUP
DVD Language for On-Screen Display
OSD MENU: The OSD MENU setup allows you to select the language for the on-screen display.
The user can either select English, French, Spanish, German or Italian for the OSD language.
Language
OSD Language
Video
Subtitle
Rating
Audio
Misc
English
French
Spanish
German
Italian
14
Language
OSD Language
: English
Video
Subtitle
: Off
Rating
Audio
: English
Misc
DVD SUBTITLE SETUP
Select "SUBTITLE" using pqbutton, then press ubutton to enter the submenu. Select the subtitle you
desire using pqbutton, then press “ENTER” to confirm the setting. Press tbutton to return.
Note: The subtitle selection is only available for discs that are recorded in the above listed languages. If the selected,
language is not available, the player will play and display on the screen the original language contained in the disc.
Language
OSD Language
Video
Subtitle
Rating
Audio
English
French
Spanish
German
Italian
Misc
Chinese
Japanese
Thai
Off
DVD AUDIO SETUP
Select "AUDIO" using pqbutton, then press ubutton to enter the submenu. Select the audio language
you desire using pqbutton, then press “ENTER” to confirm the setting. Press tbutton to return.
Note: The audio language selection is only available for discs that are recorded in the listed languages. If the selected,
language is not available, the player will play and display on the screen the original language contained in the disc.
Language
OSD Language
Video
Subtitle
Rating
Audio
English
French
Spanish
German
Italian
Misc
Chinese
Japanese
Thai
DVD VIDEO SETUP
TV Display
The TV DISPLAY setup allows you to set the screen aspect ratio.
4:3
This displays the wide picture with black bands on the upper and lower portions of the screen.
16:9
This displays a wide picture with black bands on the upper and lower portion of the screen. The band
width will vary, depending on the aspect ratio of the disc.
DVD TV Type
The TV Type setup allows you to select the television standard which corresponds to your TV.
NTSC - Select this type for NTSC TV
PAL - Select this type for PAL TV
MULTI - Select this type for multi-system TV
15
Language
TV display
Video
TV type
Rating
Misc
4:3
16:9
DVD RATING SETUP
Parental
Language
Video
Parental
: 6.Adult
Change Password
This item allows you to limit the content of movie playback from G to Adult. The lower the value, the
Rating
more strict the control.
Misc
1. G
2. PG
3. PG – 13
4. R
5. NC – 17
6. Adult
The rating level can only be changed when the correct password is provided. For first time use to change parental control, using cursor u button
to enter parental mode, key in the default password (3308) and press ENTER. Press ENTER button again to select the parental level, select the
level and press ENTER.
Change Password
To change the password to your own password select “Change Password” mode and enter the default password (3308) followed by pressing
ENTER. Press ENTER button again and key in a new four digit password.
Language
Video
Parental
: 6.Adult
Change Password
Enter Password
Rating
Misc
Note: The Default Password is 3308. This password is always effective even after you have selected your own password and changed it. To avoid the possibility
of others using the default password to set the parental level and change the password, you can record this default password in another area and delete it from this
manual. Some discs can be limited depending on the age of users while some discs cannot.
Language
DVD Misc SETUP
Video
Select "MISC” using pq button, then press u button to enter the Misc menu. Select the option you
want to change using pq button, then press ENTER.
16
Rating
Misc
Load Factory
Screen Saver
: On
Load Factory
This option allows you to reset all options to factory settings.
* This function will not affect the Rating control settings.
Language
Load Factory
Load Factory
Video
Screen Saver
Yes
No
Rating
Screen Saver
This option allows you to set the Screen saver mode.
ON -Screen saver will appear
OFF -Screen saver will not appear
Note: The DVD player will enter Screen Saver mode if the unit is inactive for approximately 2 minutes.
Misc
Language
Video
Rating
Load Factory
Screen Saver
Off
On
Misc
Playing DVDs
1. Press the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle, audio, subtitle and
time.
2. Title Selection
Press numeric(0~9) buttons to initiate a change of title selection. Then press ENTER to implement the selection.
3. Chapter selection
Press numeric(0~9) buttons to initiate a change of chapter selection. Then press ENTER to implement the selection.
17
Playing MP3 Discs
MP3 is a format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little loss of quality,
while taking up much less space. CD-R discs that have been encoded in MP3 format can be played on DVD player. The DVD player plays
the songs in the order they were burned on to the disc. When playback is started the elapsed time of the track that is playing will be
displayed.
Selecting Folders and Songs
When a device containing MP3 files is loaded in the player, the navigation menu appears automatically.
1. Press p or q to move the highlight to the desired folder (if present) on the left side of the menu and press ENTER. The songs in the folder will
be displayed on screen.
2. Press p or q to move the highlight to the desired track containing the song and press ENTER to begin track playback.
Skipping Songs
Use the Next (:) button on the remote control to move to the next song. Use the Previous (9) button to move to the previous song.
00:00:01
Selecting a Play Mode
1/12
Filter (For MP3 & JPEG only)
/
Filter
001
Filter Mode enables or disables the display of files contained on the media based on their file extension.
The filter function applies to the following formats:
Audio
Flat Mode Photo
002
Repeat :
Video
off
003
004
005
Audio - Audio data format (MP3, WMA)
Photo - Photo data format (JPEG)
Video - Video data format (MPEG , )
Music Playing
006
00:00:01
/
1/12
Flat Mode: play the entire disc
This mode is always on (default). During the Flat Mode, all the data folder with MP3, JPEG and movies will be played in
sequence. If the Flat Mode function is off, it will only play the selected folder; other folders are disabled.
001
Flat Mode
002
Repeat : Off
003
: Normal
004
005
006
18
Mode
Music Playing
Repeat: play repetitively
Repeat function has 4 options : Off, Single, Folder, All. Move cursor to Repeat function and press ENTER,
Each time ENTER is pressed the unit will cycle through the available options. Off/Single/Folder/All are
displayed in that order. Repeat default is Off;
00:00:01
/
1/12
001
Flat Mode
002
Repeat : Off
Mode
003
: Normal
004
Off
Single
Folder
All
005
Turn off repeat function
Repeat the song being played until STOP is pressed.
Play all songs in a folder repetitively
Play all songs on the disc repetitively
Music Playing
006
Mode: play mode
00:00:01
The Mode function has 4 options: Normal, Shuffle, Random and Music Intro. Move cursor to the Mode function 1/12
/
area and press ENTER repeatedly till the desired mode is displayed. Normal/Shuffle/Random/Music Intro are
001
002
displayed in that order. The Mode function default is Normal.
003
004
Normal: Play all songs in folder once.
005
Music Playing
Shuffle: Play songs in a folder in a shuffle order. Each song in the folder is played only once.
006
Random: Play songs in a folder in a random order. Each song in a folder is’t only be played once.
Music Intro: Play each song in order in the folder for 10 seconds
Remark– The purpose of the Music Intro function is to provide the user with a sample of each song for 10 seconds, thereby making it easy
to select and listen to a favorite song.
Flat Mode
Repeat : Off
Mode
: Normal
Add to program
Method: To add the selected songs into Browser view, make sure disc playback is off. Move cursor to Edit
mode function and press ENTER. After Edit mode is selected, move cursor to songs list and select the songs
which will be compiled and press ENTER. A check mark appears to the left of the selected song; to add the
selected songs to the program, move cursor to the “Add to program” function and press ENTER. The selected
songs is added into a new program list and the check mark will disappear on play list, move cursor to “Program
view” function and press ENTER to browse the songs in the program. Press play button to play the selected
songs.
19
00:00:01
/
1/12
001
Edit mode
002
Program view
003
Add to program
004
005
006
Album:------------
Music Playing
00:00:01
Clear program
1/12
Method: To clear the selected song files, press the STOP button twice during playback mode. Move the
cursor to the Edit mode function and press ENTER. After Edit mode is selected, move cursor to selected
songs list and select the songs which you want to delete. Press ENTER and a check mark will appear to
the left of the selected song. Move the cursor to clear program and press ENTER, the selected songs will be
deleted from the play list.
/
001
Edit mode
002
Broser view
003
Clear program
004
005
Music Playing
006
Album:------------
Region 1- USA, Canada
Region 2- Japan, Europe, South Africa, Middle East,
Greenland
Region 3- S. Korea, Taiwan, Hong Kong, Parts of
South East Asia
Region 4- Australia, New Zealand, Latin America
(including Mexico)
Region 5- Eastern Europe, Russia, India, Africa
Region 6- China
20
DVD Area Code
The DVD player is preset to a region code at the factory depending on where the DVD player is sold. A DVD from a different region cannot be
played in this unit and the unit will display "WRONG REGION”
DVD Basics
To get the optimum use out of the DVD section, make sure you read this section completely.
Types of Discs your DVD will play
• DVD* disc - DVD discs which contain video.
• Audio disc - Audio CDs contain musical or sound content only.
• MP3 disc - A disc that contains audio files (for example, a CD-R with downloaded MP3 files).
* This system is capable of playing most recordable DVD formats. However, due to the variety of disc manufacturers and software,
playback cannot be guaranteed.
Loading and Playing Discs
Before you load a disc, make sure that it is compatible with the player. Insert the disc with the label facing the vehicle’s headliner.
Note: the following Discs CANNOT be used with this player :
• MiniDisc
• Laserdisc
• CD-1, CD-ROM, DVD-ROM, Super Audio CD (SACD), DVD Audio, JPEG
To load and Play a Disc
Press the Power button to turn the unit on. Select DVD mode and insert the disc (label facing upwards) into the disc compartment.
21
TURNING THE UNIT ON OR OFF
1. Pushing in the Screen Release button will unlock the LCD screen and it will drop down slightly. Pivot the screen downward until a
comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use.
2. Pressing the power button* on the unit or the remote control will turn the system on and off. When in use the internal backlighting will
illuminate the controls.
3. After the unit has been turned on and is displaying a picture, adjust the viewing angle, by pivoting the screen to optimize the picture quality.
4. Remember to turn the unit off and pivot the LCD to the locked position when not in use.
Power
ON/OFF
Remote Sensor
Button Infrared Transmitter
Screen Release
22
OVERHEAD DOME LIGHTS
The Dome Lights integrated into the unit are controlled by a three position slide switch. Sliding the switch to the ON position will turn
the lights ON. The OFF position will prevent the lights from turning ON with the vehicle's interior lighting, and the auto position will allow the
lights to turn ON and OFF with the vehicle's interior lighting. Refer to the Installation Guide for wire connections. Do not leave the vehicle
unattended with the dome light switch in the ON position, as this could result in a discharged battery.
ACCESSORIES
WIRELESS HEADPHONES
The ADV10 includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using
the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the
transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your wireless
headphones.
SOURCE FEATURE
AV1
The AV1 input may be connected to a external video source, video game system, or other audio / video devices. To access the audio / video
inputs, inputs, turn the unit on and press the S (source) button or the Source button on the remote control until "AV1/AUX" is displayed on the
screen. Turn the video source component on with its power button or remote control and it is now ready to play the audio and video signals from
the source connected to AV1.
AUX
The unit will accept an audio / video input through the 3 RCA jacks located on the rear of the unit. The audio / video device could be a
video game system, video camera, or other input device. To access the audio / video inputs, inputs, turn the unit on and press the S
(source) button or the Source button on the remote control until "AV1/AUX" is displayed on the screen. Turn the video source component
on with its power button or remote control and it is now ready to play the audio and video signals from the source connected to AV1. The
same time AV1 video and audio will be cutoff.
AV Out
The unit provides an AV output for optional video monitor(s). This output will provide the AV signals that duplicate the picture/audio being
processed by the unit to an additional monitor or video display. Please see your installer for more information.
23
TROUBLESHOOTING
PROBLEM
SOLUTION
IR remote inoperative
Verify that the batteries in the remote are fresh.
Verify that the remote sensor eye is not obstructed.
Disc won't play
Insert a disc with the label side facing upwards.
Check the type of disc you put into disc tray. This DVD only plays DVD, audio CD and
MP3.
Both the unit and the disc are coded by region. If the regional codes don’t match, the
disc can’t be played.
Play starts, but then stops immediately
The disc is dirty. Clean it.
Condensation has formed. Allow player to dry out.
No sound or distorted sound
Make sure your DVD is connected properly. Make sure all cables are securely
inserted into the appropriate jacks.
If you are using the 2-channel IR headphones, make sure you turn on the IR
headphone power, make sure the correct channel (A-B) is selected.
Make sure the Modulator is ON and the proper Frequency has been selected.
Make sure that unit is set to M1 when using Single Channel Headphones.
Can’t advance through a movie
It can’t advance through the opening credits and warning information that appear
at the beginning of movies because the disc is programmed to prohibit that action.
24
SOLUTION
PROBLEM
Not allowed at the moment
The feature or action cannot be completed at this time because:
1. The disc’s software restricts it.
2. The disc’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. 4 requested a title or chapter number that is out of range.
Picture is distorted
The disc might be damaged. Try another disc.
It is normal for some distortion to appear during forward or reverse scan.
No forward or reverse scan
Some discs have sections that prohibit rapid scanning or title and chapter skip.
If you try to skip through the warning information and credits at the beginning of a
movie, you won’t be able to. This part of the movie is often programmed to prohibit
skipping through it.
25
REPLACEMENT PARTS
Remote Control
SPECIFICATIONS
136-4840
LCD Backlighting
Edge Light Tube
Resolution
1440 x 234
Pixels
336, 960
Operation Temperature
32 ~131º F (0 ~ 55º C)
Storage Temperature
-4 ~ 158º F (-20 ~ 70º C)
Backlit life
10,000 Hours
Video Display System
NTSC / PAL
Video Output
1.0Vp-p @ 75 ohms
Power Source
12V DC
Dimension
LxWxH
11.0" x 9.5" x 1.7"
289mm x 243mm x 44mm
Specifications subject to change without notice.
26
ADVENT LIMITED WARRANTY
Applies to ADVENT Mobile Video Products
R
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that, should this product or any part thereof
(except game controllers), under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original
purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.
If your new vehicle’s radio, CD/DVD player is covered by the manufacturer’s warranty for a period of 48 months as set forth in the OEM Warranty
Booklet, the company will extend the Advent Mobile Video product warranty for the same period of time. This is not applicable to extended warranty
purchases beyond the original manufacturer’s warranty. A game controller, if supplied, is similarly warranted for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for installation,
removal or reinstallation of the product, or to damage to digital memory/media devices, gaming devices, discs, speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF
THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,
SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITH IN A PERIOD NOT EXCEEDING 12
MONTHS AFTER EXPIRATION OF THE WARRANTY. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized to assume for the Company any liability other
than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 1-800-645-4994
27
128-7188B
© 2009 ADVENT,150 Marcus Blvd. Hauppauge, NY 11788
128-8567