Digital Monitoring Products XTL Series Installation guide

PROGRAMMING GUIDE
XTL/XTLC
CONTROL PANEL
MODEL XTL/XTLC
CONTROL PANEL PROGRAMMING GUIDE
When using the XTL/XTLC control for any listing organization’s approved methods, refer to this manual and the
XTL/XTLC Installation Guide. These documents outline the installation and programming requirements of all applications
for which the XTL/XTLC is approved.
FCC Notice
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with
the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the installer is encouraged to try to correct the interference by one or more of the following
measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the computer into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional
suggestions. The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2015 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Digital Monitoring Products
b
XTL/XTLC Programming Guide
TABLE OF CONTENTS
Introduction...............................................................1
1.1
Before You Begin.........................................................1
Programming Information Sheet...................................1
1.2
Getting Started............................................................1
Initializing the Panel.....................................................1
Program from an LCD or Wireless Keypad......................1
Accessing the Programmer...........................................1
1.3
Programming Menu.....................................................1
1.4
Programmer Lockout Codes..........................................2
Installing a lockout code..............................................2
1.5
Reset Timeout.............................................................2
1.6Keypad ......................................................................3
1.7
Special Keys................................................................3
COMMAND (CMD) Key..................................................3
Back Arrow (<—) Key....................................................3
Select Keys..................................................................3
1.8
Entering Alpha Characters............................................3
1.9
Entering Non-Alpha Characters.....................................4
1.10
Keypad Displays Current Programming..........................4
Initialization..............................................................5
2.1Initialization................................................................5
2.2
Clear All Codes............................................................5
2.3
Clear All Schedules......................................................5
2.4
Clear Events................................................................5
2.5
Clear Zone Programming..............................................5
2.6
Clear Communication...................................................5
2.7
Set to Factory Defaults.................................................5
Communication..........................................................6
3.1Communication...........................................................6
3.2
Account Number..........................................................6
3.3
Transmission Delay......................................................6
3.4
Communication Type....................................................6
3.5
Test Time....................................................................6
3.6
Test Days....................................................................6
3.7
Cell Check In...............................................................6
3.8
Fail Time.....................................................................6
3.9
First GPRS APN (XTL Only)...........................................6
3.10
Second GPRS APN (XTL Only).......................................7
3.11
Receiver 1 Programming..............................................7
3.12
Alarm Reports.............................................................7
3.13
Supervisory/Trouble Reports.........................................7
3.14
Opening/Closing and User Reports................................7
3.15
Test Report.................................................................7
3.16
First IP Address...........................................................7
3.17
First IP Port.................................................................7
3.18
Second IP Address.......................................................7
3.19
Second IP Port............................................................7
3.20
Receiver 2 Programming..............................................7
3.21
Alarm Reports.............................................................7
3.22
Supervisory/Trouble Reports.........................................7
3.23
Opening/Closing and User Reports................................7
3.24
Test Report.................................................................8
3.25
First IP Address...........................................................8
3.26
First IP Port.................................................................8
3.27
Second IP Address.......................................................8
3.28
Second IP Port............................................................8
XTL/XTLC Programming Guide
Digital Monitoring Products
i
TABLE OF CONTENTS
Messaging Setup........................................................9
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
Messaging Setup.........................................................9
Enable Messaging........................................................9
System Name..............................................................9
Destination 1...............................................................9
Destination 1 User Number...........................................9
Destination 2...............................................................9
Destination 2 User Number...........................................9
Destination 3...............................................................9
Destination 3 User Number...........................................9
O/C Email.................................................................10
O/C SMS...................................................................10
Monthly Limit............................................................10
Device Setup............................................................11
5.1
5.2
5.3
5.4
5.5
5.6
Device Setup.............................................................11
Device Number..........................................................11
Device Name.............................................................11
Wireless....................................................................11
Serial Number...........................................................11
Supervision Time.......................................................11
Remote Options.......................................................12
6.1
6.2
6.3
Remote Options.........................................................12
Remote Key...............................................................12
Remote Disarm..........................................................12
System Reports........................................................13
7.1
System Reports.........................................................13
7.2
Opening/Closing Reports............................................13
7.3
Abort Reports............................................................13
7.4
Zone Restoral Reports................................................13
7.5
Bypass Reports..........................................................13
7.6
Code Change Reports................................................13
7.7Ambush....................................................................13
7.8
Late To Open.............................................................13
7.9
Early To Close............................................................13
System Options........................................................14
8.1
System Options.........................................................14
8.2System.....................................................................14
8.3
Closing Code.............................................................14
8.4
Closing Check............................................................14
8.5
Entry Delay 1............................................................14
8.6
Exit Delay.................................................................14
8.7
Cross Zone Time........................................................15
8.8
Power Fail Delay........................................................15
8.9
Swinger Bypass Trips.................................................15
8.10
Reset Swinger Bypass................................................15
8.11
Zone Activity Hours....................................................15
8.12
Arm Activity Days......................................................15
8.13
Time Zone Changes...................................................16
8.14
Time Display.............................................................16
8.15
House Code..............................................................16
8.15.1 Detect Wireless Jamming...........................................16
8.15.2 Wireless Audible Annunciation....................................16
8.16
Enable Keypad Panic Keys..........................................16
8.17
Occupied Premises.....................................................17
8.18
Use False Alarm Question...........................................17
8.19
Weather Zip Code......................................................17
Digital Monitoring Products
ii
XTL/XTLC Programming Guide
TABLE OF CONTENTS
Bell Options..............................................................18
9.1
Bell Options...............................................................18
9.2
Bell Cutoff Time.........................................................18
9.3
Automatic Bell Test....................................................18
9.4
Bell Output................................................................18
9.5
Bell Action.................................................................18
9.5.1Fire...........................................................................18
9.5.2Burglary....................................................................18
9.5.3Supervisory...............................................................18
9.5.4Panic........................................................................18
9.5.5Emergency................................................................18
9.5.6
Auxiliary 1.................................................................18
9.5.7
Auxiliary 2.................................................................18
Output Options........................................................19
10.1
10.2 10.3 10.4
10.5
10.6
10.7
10.8
10.9
10.10
10.11 10.12
10.13
10.14
Output Options..........................................................19
Communication Failure Output....................................19
Fire Alarm Output......................................................19
Panic Alarm Output....................................................19
Entry Output.............................................................19
Begin Exit Output......................................................19
End Exit Output.........................................................19
Armed Output...........................................................19
Disarmed Output.......................................................20
Burglary Output.........................................................20
Ready Output............................................................20
Arm-Alarm Output.....................................................20
Heat Saver Temperature.............................................20
Cool Saver Temperature.............................................20
Output Information.................................................21
11.1
11.2
11.3
11.4
11.5
11.6
Output Information....................................................21
Output Number.........................................................21
Output Name............................................................21
Serial Number...........................................................21
Supervision Time.......................................................21
Trip with Panel Bell Option..........................................21
Area Information.....................................................22
12.1
12.2
12.3
12.4
12.4.1
12.5
Area Information.......................................................22
Area Number.............................................................22
Area Name................................................................22
Automatic Arming......................................................22
Bad Zones.................................................................22
Automatic Disarming .................................................22
Zone Information.....................................................23
13.1
Zone Information.......................................................23
13.2
Zone Number............................................................23
13.3
Key Fob....................................................................23
13.4
Zone Name...............................................................24
13.5
Zone Type.................................................................24
13.6
Area Assignment.......................................................24
13.7
Arming Zone Assignment............................................24
13.7.1Style.........................................................................25
DMP Wireless............................................................25
13.9
Serial Number Entry...................................................25
13.10Contact.....................................................................25
13.10.1 Supervision Time.......................................................26
13.10.2 LED Operation...........................................................26
XTL/XTLC Programming Guide
Digital Monitoring Products
iii
TABLE OF CONTENTS
13.10.3Disarm/Disable..........................................................26
13.10.4 Wireless PIR Pulse Count...........................................26
13.10.5 Wireless PIR Sensitivity..............................................26
13.10.6 Next Zone.................................................................26
13.11 Series Key Fobs.........................................................27
13.11.1 Key Fob User Number................................................27
13.11.2 Key Fob Serial Number...............................................27
13.11.3 Key Fob Supervision Time..........................................27
13.11.4 Number of Key Fob Buttons........................................27
13.11.5 Key Fob Button Selection (Four Buttons).....................27
13.11.6 Key Fob Button Selection (Two Buttons)......................27
12.11.7 Button Action............................................................27
13.11.8 Button Press Time.....................................................28
13.11.9 Arm/Disarm Area Selection.........................................28
13.11.10 Output Number.........................................................28
13.11.11 Output Action............................................................28
13.12 Alarm Action.............................................................29
13.13 Disarmed Open.........................................................29
13.13.1 Message To Transmit..................................................29
12.13.2 Output Number.........................................................29
13.13.3 Output Action............................................................30
13.14 Swinger Bypass.........................................................30
13.15 Prewarn Address........................................................30
13.16 Entry Delay...............................................................30
13.17 Cross Zone................................................................30
13.18Priority......................................................................31
13.19 Traffic Count..............................................................31
13.20 Zone Audit Days........................................................31
13.21 Receiver Routing.......................................................31
13.22 Zone Number............................................................31
Stop..........................................................................32
14.1Stop.........................................................................32
Set Lockout Code.....................................................32
15.1
Set Lockout Code.......................................................32
Appendix..................................................................33
16.1
16.2
16.3
16.4
16.5
16.6
Digital Monitoring Products
iv
Status List.................................................................33
Transmission Delay....................................................33
False Alarm Reduction................................................33
System Recently Armed report....................................33
Diagnostics Function..................................................33
Cellular Status...........................................................33
Cellular Signal Strength (CELL SIGNAL).......................33
Cell Roaming Indicator on XTLC..................................34
Cellular Activation......................................................34
Activation for XTL......................................................34
Activation for XTLC....................................................34
Panel Settings...........................................................34
Serial Number...........................................................34
Panel Model..............................................................34
Firmware Version.......................................................34
Z-Wave Test Option....................................................34
Exiting the Diagnostics program..................................34
Using the 984 Command Function...............................35
Using the Walk Test...................................................35
Walk Test..................................................................35
Trip Counter For DMP Wireless Check-in Test (WLS).....35
Test End Warning......................................................35
XTL/XTLC Programming Guide
TABLE OF CONTENTS
16.7
16.8
16.9
16.9
16.10 16.11 Failed Zones Display..................................................35
Keypad Speaker Operation.........................................36
Cross Zoning.............................................................36
Zone Type Descriptions..............................................36
Zone Type Defaults....................................................38
Common Keypad Messages........................................39
Z-Wave Certification Information.................................39
Revisions to This Document.....................................40
Certifications...........................................................................42
XTL/XTLC Programming Guide
Digital Monitoring Products
v
INTRODUCTION
1.1
Before You Begin
Introduction
Before starting to program, we recommend you read through the contents of this manual. The information in
this document allows you to quickly learn the programming options and operational capabilities of the XTL/
XTLC panel.
After this Introduction, the remaining sections describe the functions of each programming menu items along
with their available options. The XTL/XTLC contains all of its programming information in an on-board processor
and does not require an external programmer.
In addition to this manual, you should also be familiar with the following documents:
• XTL/XTLC Installation Guide (LT-1105)
• XTL/XTLC/XTLN/XTLN-WiFi User’s Guide (LT-1109)
• XTL/XTLC Programming Sheet (LT-1095)
Programming Information Sheet
Included with each XTL/XTLC panel is the Programming Sheet. This sheet lists the various options available for
programming the panel. Before starting, completely fill out the sheet with the programming options you intend
to enter into the panel.
Having completed programming sheets available while entering data helps to prevent errors and can shorten
the length of time you spend programming. Completed sheets also provide you with an accurate account of the
panel’s program you can keep on file for future system service or expansion.
The remainder of the Introduction explains starting and ending a programming session.
1.2
Getting Started
Ground Yourself Before Handling the Panel! Touch any grounded metal before touching the panel to discharge
static.
The XTL/XTLC panel should be completely installed before you begin programming. Make sure the AC and
battery wires are correctly installed.
Initializing the Panel
When programming a panel for the first time or rewriting the entire program of an existing XTL/XTLC, use the
Initialization function described in section 2. Initializing clears the panel’s memory of any old data and sets the
highest numbered user number to user code 99.
Program from an LCD or Wireless Keypad
You can program the panel using an LCD Keypad connected to the panel PROG header.
Wireless Keypads can be used for panel programming after being programmed in the panel manually or by using
the Wireless Keypad Association operation.
To enable association operation in the panel, press the XTL/XTLC RESET button 3 times within 12 seconds
allowing 3 seconds between each press of the reset button. When in keypad association, the XTL/XTLC Red and
Green logo LEDs turn on steady.
For 60 seconds the panel listens for wireless keypads that are in the Installer Options Menu (3577 CMD) and
have not been programmed, or associated into another panel. Those keypads are assigned to the first open
device position automatically based upon the order in which they are detected. The keypad logo turns Green to
indicate it has been associated with the panel. See the 9000 Series Wireless Keypad Installation Guide (LT-1107)
for additional information.
Note: Programming can not be accessed using an Icon Series keypad. Use a 32-character keypad to complete
the panel programming.
Accessing the Programmer
To access the programmer function of the XTL/XTLC:
1. If using a standard LCD keypad, connect to the PROG header and set the keypad to Address 1.
2. If using a wireless LCD keypad, make sure panel communication has been established and the user menu
appears on an associated keypad before continuing.
3. Press the RESET button for two seconds.
4. Enter the code 6653 (PROG).
5. The keypad displays: PROGRAMMER.
6. Remove the hardwired keypad (if used) when programming is completed.
1.3
Programming Menu
XTL/XTLC Programming Guide
Digital Monitoring Products
1
INTRODUCTION
You are now ready to start programming the XTL/XTLC panel. Pressing the COMMAND key scrolls you through
the programming menu items listed below.
Menu Item
Section in This Manual
Menu Item
Section in This Manual
Initialization
2
Output Options
10
Communication
3
Output Information
11
Messaging Setup
4
Area Information
12
Device Setup
5
Zone Information
13
Remote Options
6
Stop
14
System Reports
7
Set Lockout Code
15
System Options
8
Appendix
16
Bell Options
9
To select a section for programming, press any Select key when the name of that section displays on the
keypad. The detailed instructions for each programming step are found in sections 2 to 17 of this manual.
1.4
Programmer Lockout Codes
Although the XTL/XTLC panel allows access to Programming without a lockout code, it is available to program
one to restrict programming access to authorized individuals only. You can do this by using SET LOCKOUT CODE
at the end of the programming menu.
Installing a lockout code
1. After entering the Programmer menu, the keypad displays PROGRAMMER. Press the COMMAND key until
SET LOCKOUT CODE is displayed (after STOP).
2. Press any Select key. At the ENTER CODE: - display, enter a 1- to 5-digit programmer lockout code. Press
COMMAND.
3. The display shows ENTER AGAIN. Enter the same lockout code again and press COMMAND. The display
shows CODE CHANGED. The new code number must now be entered before the Programmer menu can
be accessed.
The lockout code should be written down and kept in a secure place with access limited to authorized persons
only.
Lost Lockout Code requires factory reset: If you lose or forget the lockout code, the panel must be sent back
to the factory to be reset. There is no field option for gaining access to the panel without a valid lockout code.
1.5
Reset Timeout
The XTL/XTLC has a feature that requires you to enter the Programmer within 30 minutes of resetting the
panel. After 30 minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad displays:
RESET PANEL. You must reset the panel and enter the program code within the next 30 minutes.
If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes, the
panel terminates programming. All data entered up to that point is saved in the panel’s memory.
To exit the panel’s Programmer you must use the Stop function. The STOP option is the second to the last
option in programming. The programming session is then terminated and the keypad returns to the Status List.
Digital Monitoring Products
2
XTL/XTLC Programming Guide
INTRODUCTION
1.6Keypad
Connect up to four DMP 9060 and 9063 Wireless LCD Keypads to the XTL/XTLC panel. The operation is shown
and described in the following sections.
32-Character Display
SMITH HOME
F R I 2 : 51 AM
Select Keys
Backlit Logo
and Proximity
Antenna
1
2
3
4
5
6
7
8
9
0
CMD
COMMAND Key
Back Arrow Key
Data Entry Digit keys
Figure 1: 9000 Series Wireless Keypad
1.7
Special Keys
The following special keys are common to all DMP keypads.
COMMAND (CMD) Key
Pressing the COMMAND key allows you to go forward through the programming menu and through each step of a
programming sec­tion. As you go through the programming, the keypad display shows any current programming
already stored in the panel memory. If no change is required for an option, press the COMMAND key to advance
to the next step.
The COMMAND key is also used to enter information into the panel’s memory such as phone numbers or zone
names. Press the COMMAND key after entering information.
Back Arrow (<—) Key
Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when an error
is made while entering in­formation. Press the Back Arrow key once to erase the last character entered.
Select Keys
The top row of keys are called the Select keys on the 9000 Series Wireless Keypad.
Each time you need to press a Select key on 9000 Series keypad, the keypad displays the function or options
above one of the keys. Displaying choices above individual Select keys allows them to be used for many
different applications. For example, you can enter AM or PM when programming the automatic test time or
answer YES or NO for a system option.
During programming, the Select keys also allow you to change infor­mation currently in panel memory by
pressing the appropriate Select key under or on the display. You then enter the new information using the
keypad data entry digit keys. The Select keys are also used for choosing a section from the pro­gramming menu.
When the programming section name you want displays, press any Select key.
When there are more than four re­sponse options avail­able, press the COMMAND key to display the next one to
four options. Pressing the Back Arrow key allows you to review the previous four choices.
Note: When instructed to press the first Select key, press the far left Select key; the second Select key is the
second from the left; third Select key is second from the right; and the fourth Select key is the far right key.
See Figure 2.
1.8
Entering Alpha Characters
Some options during programming require you to enter alpha characters. To enter an alpha character, press
or touch the key that has that letter written below it. The keypad displays the number digit of the key. Next,
press the Select key that corresponds to the loca­tion of the letter under the key. Pressing a different Select key
changes the letter. When an­other digit key is pressed, the last
A
B
C
(
letter displayed is retained and the process starts over.
First Letter
Third Letter
Second Letter
Special Character
Figure 2: 9060/9063 Select Keys
XTL/XTLC Programming Guide
Digital Monitoring Products
3
INTRODUCTION
1.9
Entering Non-Alpha Characters
To enter a space in an alpha entry, press the 9 digit key followed by the third Select key. The three characters
on the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash), . (period), *
(asterisk), and # (pound sign) using the 0 (zero) key and the four Select keys from left to right. For example, to
enter a – (dash), press the 0 (zero) key and then the left Select key. A dash now appears in the keypad display.
The table below shows the character locations for DMP keypads.
Key Number
1
2
3
4
5
6
7
8
9
0
1.10
Select Key 1
A
D
G
J
M
P
S
V
Y
-
Select Key 2
B
E
H
K
N
Q
T
W
Z
.
Select Key 3 Select Key 4
C
(
F
)
I
!
L
?
O
/
R
&
U
@
X
,
space
_
*
#
Keypad Displays Current Programming
Each programming option displayed at the keypad shows the currently selected option in the panel memory.
These options are either shown as a number, a blank, or a NO or YES. To change a number or blank to a new
number, press any top row Select key. The current option is replaced with a dash. Press the number(s) on the
keypad you want to enter as the new number for that option. It is not necessary to enter numbers with leading
zeros. The panel automatically right justifies the number when you press the COMMAND key.
To change a programming option that requires a NO or YES response, press the Select key for the response not
selected. See Figure 3.
For example, if the current option is selected as YES and you want to change it to NO, press the third top row
Select key. The display changes to NO. Press the COMMAND key to display the next option.
Press the third top row
Select key.
BELL TST
THEN
YES
The keypad displays the new
selection. Press CMD to advance.
BELL TST
NO
Figure 3: Changing the Current Programming Option
Digital Monitoring Products
4
XTL/XTLC Programming Guide
INITIALIZATION
Initialization
INITIALIZATION
2.1Initialization
This function allows you to set the panel’s programmed memory back to the factory
defaults in preparation for system programming.
After you select YES to clear a section of memory, the panel asks if you are sure you
want to clear the memory. This is a safeguard against accidently erasing part of your
programming. No memory is cleared from the programming until you answer YES to the
SURE? YES NO option.
For each section of the panel program you
can initialize, a NO or YES option is provided.
CODES?
NO
YES
Selecting YES advances you to
a confirmation prompt.
SURE?
Selecting NO advances
you to the next prompt.
SCHEDS?
2.2
CODES?
SURE?
YES
NO
If you select YES, the panel initializes that section of
the program and advances you to the next prompt.
NO
YES
If you select NO, the panel advances you to the next
section prompt but does not initialize that section of
the program.
NO YES Clear All Codes
YES NO NO leaves existing user codes intact.
YES clears the user code memory and assigns the user code number 99 to user 30 on the
XTL/XTLC.
2.3
SCHEDS?
SURE?
NO YES Clear All Schedules
YES NO NO - Leaves existing schedules intact.
YES - Clears all schedules from panel programming.
2.4
2.5
2.6
2.7
EVENTS?
SURE?
NO YES Clear Events
YES NO NO leaves existing event memory intact.
ZONES?
SURE?
NO YES Clear Zone Programming
YES NO NO leaves existing zone information intact.
COMM?
SURE?
NO YES Clear Communication
YES NO NO - Leaves existing communication and messaging programming intact.
YES clears all event memory currently held in the panel’s Display Events buffer.
YES sets all zones in the system to * UNUSED *
YES - Clears communication and messaging programming to factory defaults.
DEFAULTS? NO YES Set to Factory Defaults
SURE? YES NO NO leaves the remainder of the existing panel programming intact.
YES sets the panel’s programming back to factory default selections and clears all
Z-Wave device programming and all Favorites from the panel. Selecting YES does not
clear the panel’s event memory, zone, user code information, or schedules.
XTL/XTLC Programming Guide
Digital Monitoring Products
5
COMMUNICATION
Communication
3.1Communication
COMMUNICATION
The Communication section allows you to configure the communication settings for the
XTL/XTLC panel. After choosing the Communication Type, continue through the list of
options.
3.2
ACCOUNT NO:
3.3
XMIT DELAY:
3.4
COMM TYPE: CELL Communication Type
This specifies the communication method the panel uses to contact the receiver. Press
CELL NONE
3.5
Account Number
30
Enter the account num­ber sent to the receiver.
The range of account numbers are 1 to 65535. For account numbers of four digits or
less, you do not have to enter leading zeros. The panel automatically right justifies the
account number.
Transmission Delay
Enter the number of seconds (15 to 45 seconds) the panel waits before sending burglary
alarm reports to the receiver. The wireless siren and relay outputs are not delayed during
this period. Enter 0 (zero) to disable this function. The default is 30.
any Select key to display the following communication options:
CELL - Cellular communication to DMP Model SCS-1R or SCS-VR Receivers.
NONE - For local systems. Selecting this ends communication programming.
Note: XTLC cellular communication must be activated using the Activate Cell option
provided in section 17.4 Diagnostics Function located in the Appendix.
Test Time
TEST TIME
Press COMMAND to enter the Test Time. Enter the time of day the panel sends the test
00:00 AM PM report to the SCS-1R Receiver. Use entries between 12:00 to 11:59 and then choose AM
or PM.
3.6
3.7
CELL TST DAYS:
1
CELL CHECKIN:
0
Test Days
Enter how often the panel test report is sent to the receiver. Enter from 1 to 60 days.
Enter zero to disable the test report. Default is 1 (one) day. This option only displays if a
test time is entered.
Cell Check In
Check-in reports are a method of supervising the panel for communication with the
receiver.
Enter the number of minutes between check-in reports. Select from 0 or 3-240 minutes.
Enter 0 (zero) to disable the check-in option. Default is 0.
Note: If Cell Check-in option is used, additional cell charges may apply.
3.8
FAIL TIME: 240
Fail Time
Fail Time allows the SCS-1R or SCS-VR receiver to miss a defined number of check-ins
before logging that the panel is missing. For example, if CELL CHECKIN is 20 and FAIL
TIME is 30, the SCS-1R receiver only indicates a Panel Not Responding after 30 minutes.
The FAIL TIME must be equal to or greater than the CELL CHECKIN minutes: If the
CHECKIN is 20 minutes, the FAIL TIME must be 20 or more. The maximum FAIL TIME is
240 minutes. Select from 0 or 3-240 minutes. The default FAIL TIME is 240 minutes.
Closing Wait operation: Closing Wait operation is activated if Fail Time is set
to 3 minutes and O/C Reports in System Reports is YES and O/C User reports in
Communication Programming is set to YES.
Closing Wait provides a delay time before a monitored system arms until the panel
receives an acknowledgment of the closing report from the central station receiver.
During the delay, the keypad displays ONE MOMENT . . . Once the closing is
acknowledged from the SCS-1R receiver, the keypad buzzes for one second and then
displays an armed status message. If the primary communication fails, the message
LOCAL ALARM ONLY appears.
3.9
FIRST GPRS APN
SECURECOM400
-
Digital Monitoring Products
6
First GPRS APN (XTL Only)
Enter the first APN (Access Point Name). This allows an access point for cellular
communication and is used to connect to a DNS network. The APN may contain two lines
of 16 characters to equal 32 characters. Default is set to SECURECOM400.
XTL/XTLC Programming Guide
COMMUNICATION
3.10
3.11
SECOND GPRS APN
SECURECOM400
RECEIVER 1 PROG
Second GPRS APN (XTL Only)
Enter the second APN (Access Point Name). This works as a backup in case the first APN
fails. The APN may contain two lines of 16 characters to equal 32 character Default is
set to SECURECOM400.
Receiver 1 Programming
Allows you to set the options for the first receiver the panel attempts to contact when
sending reports. The XTL/XTLC supports communication to two receivers.
3.12
ALARM 3.13
SPV/TRBLNOYES
3.14
O/C USER NOYES
Opening/Closing and User Reports
3.15
TEST RPT NO YES
Test Report
3.16
FIRST IP ADDR
000.000.000.000
NO YES
Alarm Reports
YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and
System Recently Armed reports to be sent to this receiver. Default is YES.
Supervisory/Trouble Reports
YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and
Fault reports to be sent to this receiver. Default is YES.
YES enables Opening/Closing, Code Changes, and Bypass reports by user to be sent to
this receiver. Default is NO.
Enter YES to enable the Recall Test report to be sent to this receiver.
First IP Address
Enter the first (primary) IP address where the panel sends cell messages. Enter all
12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as
192168000250. The periods display automatically.
The message is sent using first GPRS APN and the first IP Address. If no acknowledgment
is received, first GPRS APN and the second IP address are used, followed, if needed, by
second GPRS APN and first and second IP addresses, respectively.
3.17
First IP Port
FIRST IP PORT
2001 Enter the first IP port number to be used in conjunction with the first IP Address. The
IP port identifies the port used to communicate messages to and from the panel.
The default IP Port setting is 2001.
3.18
SECOND IP ADDR
000.000.000.000
Second IP Address
3.19
Second IP Port
SECOND IP PORT
2001
Enter the second IP port number to be used in conjunction with the second IP address.
Enter the second IP address where the panel sends network messages. Enter all 12
digits and leave out the periods. For example, enter IP address 192.168.0.250 as
192168000250. The periods display automatically.
The IP port identifies the port used to communicate messages to and from the panel.
The default IP Port setting is 2001.
3.20
RECEIVER 2 PROG
Receiver 2 Programming
Allows you to set the options for the second receiver the panel attempts to contact
when sending reports. The XTL/XTLC supports communication to two receivers. If you
select YES for any of the Receiver 2 options, you must have at least one IP address
programmed in Receiver 2 programming. Receiver 2 defaults are set to NO.
3.21
ALARM 3.22
SPV/TRBL NOYES
3.23
O/C USER NOYES
NOYES
Alarm Reports
YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and
System Recently Armed reports to be sent to this receiver. Default is NO.
Supervisory/Trouble Reports
YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and
Fault reports to be sent to this receiver. Default is NO.
XTL/XTLC Programming Guide
Opening/Closing and User Reports
YES enables Opening/Closing, Code Changes, and Bypass reports by user to be sent to
this receiver. Default is NO.
Digital Monitoring Products
7
COMMUNICATION
3.24
TEST RPT NOYES
Test Report
3.25
FIRST IP ADDR
000.000.000.000
First IP Address
YES enables the Recall Test report to be sent to this receiver. Default is NO.
Enter the first (primary) IP address where the panel sends cell messages. Enter all
12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as
192168000250. The periods display automatically.
The message is sent using first GPRS APN and the first IP Address. If no acknowledgment
is received, first GPRS APN and the second IP address are used, followed, if needed, by
second GPRS APN and first and second IP addresses, respectively.
3.26
3.27
3.28
FIRST IP PORT
First IP Port
2001 Enter the first IP port number to be used in conjunction with the First IP Address. The
IP port identifies the port used to communicate messages to and from the panel. The
default IP Port setting is 2001.
SECOND IP ADDR
000.000.000.000
Second IP Address
Enter the second IP address where the panel sends cell messages. Enter all 12 digits and
leave out the periods. For example, enter IP address 192.168.0.250 as 192168000250.
The periods display automatically.
Second IP Port
SECOND IP PORT
2001 Enter the second IP port number to be used in conjunction with the second IP Address.
The IP port identifies the port used to communicate messages to and from the panel.
The default IP Port setting is 2001.
Digital Monitoring Products
8
XTL/XTLC Programming Guide
MESSAGING SETUP
Messaging Setup
4.1
MESSAGING SETUP
Messaging Setup
This section allows you to enter the information needed to send and receive messages
directly to and from the panel via email and MyAccess™ text messaging using CDMA
cellular communication. All of the name and password options below allow up to 32
lowercase characters to be entered. The Destination addresses allow up to 48 characters
to be entered. System Name is displayed with initial caps.
The transmitted messages are:
•
•
•
•
•
•
•
•
•
•
•
•
•
4.2
Zone Alarms by Zone Name
Zone Troubles by Zone Name
Zone Bypass by User
Arming (Closings) by User
Disarming (Openings) by User
Late to Close
Late to Open
Early to Close
AC Power Trouble and Restoral
System Low Battery
Ambush
Abort, Cancel and Alarm Verified by User
Check-in by User
Enable Messaging
ENABLE MESSAGING
NOYES Select YES to allow the panel to send messages to three programmed destinations.
Default is NO.
4.3
4.4
System Name
SYSTEM NAME
-
Enter a unique name for the panel. The panel name is used as the sender of the
message. The text entered is displayed with initial caps. If this field is left blank, the
panel account number is sent.
Destination 1
DESTINATION 1
-
Enter the first email address or cell phone number where messages will be sent. The
message can be sent to any device (computer, cell phone, PDA) as long as a valid email
address or cell phone number is entered. When entering email addresses, press the
7 digit key followed by the fourth Select Key to add the @ symbol and the 9 digit key
followed by the fourth Select Key to add the _ symbol. See the Entering Non-Alpha
Characters section for additional symbols.
Note: Mail servers that require Transport Layer Security (TLS) encryption are not
supported by the XTL/XTLC.
4.5
4.6
4.7
4.8
4.9
DESTINATION 1
USER NUMBER:
Destination 1 User Number
0
Destination 2
DESTINATION 2
DESTINATION 2
USER NUMBER:
Enter the second destination email address or cell phone number.
Destination 2 User Number
0
XTL/XTLC Programming Guide
If Destination 2 is a cellular number, enter the user’s User Number for
arming/disarming authorization.
Destination 3
DESTINATION 3
DESTINATION 3
USER NUMBER:
If Destination 1 is a 10-digit cellular number, enter a user’s user number from this account.
This option is used when sending commands such as arming or disarming back to the panel
using MyAccess™ text messaging from the same cell phone or PDA. The user number must
have the authority to perform the commands as if it occurred at the keypad. Entering 0
(zero) disables this option. Default is 0.
Enter the third destination email address or cell phone number.
Destination 3 User Number
0
If Destination 3 is a cellular number, enter the user’s User Number for
Digital Monitoring Products
9
MESSAGING SETUP
arming/disarming authorization.
4.10
4.11
O/C EMAIL NOYES
O/C SMS
NOYES
O/C Email
Select YES to allow the panel to send Opening and Closing reports via email. Default is NO.
This option appears only if any destination is an email address.
O/C SMS
Select YES to allow the panel to send Opening and Closing messages to a cell phone via SMS
protocol. Default is NO. This option appears only if any destination is a cell phone number.
4.12
MONTHLY LIMIT:
0
Monthly Limit
This option displays if any programmed destination is a cell phone number or an
email address. This number limits the monthly incoming and outgoing SMS messages
allowed to be sent or received by the panel.
A panel event that causes messages to be sent to destination cell phone numbers
or destination email addresses is counted towards the panel’s monthly limit. For
example, if an alarm message is sent to a cell phone number and an email address,
a total of 2 messages are counted towards the monthly limit for the panel. SMS
messages sent from a cell phone to the panel, including status requests and
MyAccess™ text messaging commands, also count toward the monthly limit. The
limit is reset at midnight on the 14th of every month. Range is from 0 to 999.
When 0 is entered, there is no limit on the number of messages able to be sent or
received by the panel. Default is 0.
Note: The SecureCom Wireless text plan selected for the panel should match or exceed
the programmed Monthly Limit.
Digital Monitoring Products
10
XTL/XTLC Programming Guide
DEVICE SETUP
Device Setup
5.1
DEVICE SETUP
Device Setup
This section allows you to define the panel wireless keypad configuration. You can install
and address up to four wireless keypads.
5.2
DEVICE NO:-
5.3
* UNUSED *
Device Number
Enter the device number of the wireless keypad you are programming. The valid range is
2-5.
Note: Address one is reserved for the XTL/XTLC programming keypad attached during
programming. After you program each option for the first keypad, repeat these
programming steps for each additional keypad.
Device Name
This section allows you to define a 16 character alphanumeric name for the device
number. If no name is entered, *UNUSED* is displayed.
To remove a keypad from the system, delete the device name by pressing any Select key,
then press the COMMAND key. The device name is now displayed as * UNUSED *.
5.4
5.5
5.6
WIRELESS? NO YES
Wireless
Select YES to use a wireless keypad. Default is YES.
SERIAL#: XXXXXXXX
Serial Number
Enter the eight-digit serial number found on the wireless keypad.
Supervision Time
SUPRVSN TIME: 240 Press any top row key to select the supervision time required for the device. Press
COMMAND to accept the default time. Default is 240 minutes.
SELECT MINUTES:
0
60
240
Press the Select key under the required number of minutes. The device must check in at
least once during this time or a missing condition is indicated for that device. Zero (0)
indicates an unsupervised wireless keypad.
Note: When the panel is reset, panel is powered down and powered up, or programming
is complete, the supervision timer restarts for all wireless keypads.
XTL/XTLC Programming Guide
Digital Monitoring Products
11
REMOTE OPTIONS
Remote Options
6.1
REMOTE OPTIONS
Remote Options
This section allows you to enter the information needed for Remote Command/Remote
Programming operation via CELL communication. A description of the Remote Options
follows:
6.2
RMT KEY:
Remote Key
This option allows you to enter a code of up to eight digits for use in verifying the
authority of an alarm or service receiver to perform a remote command/programming
session. The receiver must give the correct key to the panel before being allowed
access. All panels are shipped from the factory with the Remote Key preset as blank.
To enter a new Remote Key, press any Select key and enter any combination of up to 8
digits. The numbers you enter appear as asterisks. Press COMMAND.
6.3
DISARMNO
YES
Digital Monitoring Products
12
Remote Disarm
Enter YES to enable the panel to be disarmed remotely. Selecting NO disables remote
disarming.
XTL/XTLC Programming Guide
SYSTEM REPORTS
System Reports
7.1
SYSTEM REPORTS
System Reports
This function allows you to select the reports the XTL/XTLC sends to the receiver.
7.2
O/C RPTS
NOYES
7.3
ABORT
NO
NOYES
Opening/Closing Reports
NO - No Opening/Closing Reports are sent.
YES - Sends Opening/Closing Reports for each programmed area.
Abort Reports
YES allows the panel to send an Alarm Abort Report to the receiver any time an area is
disarmed during Transmit Delay before an alarm report is sent and the Bell Cutoff Time
has not expired. See the Bell Cutoff section. The area must be disarmed and no zones
that were in alarm can still be armed.
YES also allows a Bell Silenced Report to be sent if the alarm bell is silenced with a valid
user code during an alarm. Default is NO.
Note: Alarm Cancel or Verify Reports are sent if the alarm is canceled or verified after
being sent to the alarm receiver, if the Bell Cutoff timer has not expired. The Abort
Reports option does not affect Cancel or Verify reports.
The panel will not send Abort reports for Fire zones, or Supervisory-type zones.
7.4
RESTORAL YES
NO YES D
ISARM
7.5
BYPASS
7.6
CODE CHG NOYES
NO YES
Zone Restoral Reports
This option allows you to specify whether the panel sends zone restoral reports and
when they will be sent.
NO - Restoral reports are not sent by the panel.
YES - The panel always sends zone restoral reports at the time the zone restores from
an alarm or trouble condition.
DISARM - The panel sends zone restoral reports when a zone that has restored from an
alarm or trouble is disarmed. Twenty-four hour zones send restorals immediately.
Bypass Reports
YES allows the panel to send all zone bypass, reset, and force arm reports to the
receiver. The bypass report includes the zone number, zone name, and the user number
of the individual bypassing the zone.
Code Change Reports
YES allows the panel to send all code additions, changes, and deletions to the receiver.
The code change report includes the user number added or deleted and the user number
of the individual making the change.
7.7Ambush
AMBUSH NOYES
YES allows an ambush report to be sent any time user code number one is entered at a
keypad. Selecting NO disables the ambush report and allows user code number one to
operate the same as all other codes.
7.8
LATE TO OPEN
Late To Open
7.9
EARLY TO CLOSE
Early To Close
XTL/XTLC Programming Guide
Enter 1-240 as the number of minutes to elapse that the system may remain armed after
the opening time of a schedule without sending a Late To Open message. If the system
continues to be armed after the Late to Open minutes expire, a Late To Open message is
sent to the central station. Default is 0, which disables the Late To Open option.
Enter 1-240 as the number of minutes that the system can be armed prior to the
scheduled closing time. If the system is armed prior to the Early to Close minutes, an
Early To Close message is sent to the central station. Default is 0, which disables the
Early to Close option.
Digital Monitoring Products
13
SYSTEM OPTIONS
System Options
8.1
System Options
SYSTEM OPTIONS
This section allows you to select system wide parameters used in the operation of the
XTL/XTLC panel. A description of each System Option follows:
8.2System
SYSTEM: ALL/PERIM
This configures the panel as either a six Area system, an All/Perimeter system
(Perimeter/Interior), or a Home/Away system (Perimeter, Interior, and Bedrooms). Zones
must be assigned to Bedrooms for the area to be active.
Wireless zones in an Area or All/Perimeter system resound the trouble buzzer every four
hours when zone trouble or low battery is displayed.
AREAA/P H/A
8.3
8.4
8.5
8.6
CLS CODE NOYES
CLS CHK
NOYES
Closing Code
When YES is selected, a code number is required for system arming. If NO is selected, a
code number is not required for system arming. Default is NO.
Closing Check
Select YES to enable the panel to verify that all areas have been armed after a schedule
expires. If the Closing Check finds any areas disarmed past the scheduled time, all
keypads emit a steady beep and display CLOSING TIME!. The user must extend the
schedule or arm the system within 10 minutes or a Late to Close message is sent to the
central station. Default is NO.
ENTRY DLY 1:
ENTRY DLY 2:
30 Entry Delay 1
60 Enter the entry delay time for all exit type zones programmed to use Entry Delay 1.
EXIT DELAY:
60
When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding.
ENTER CODE:- and the name of the zone causing the Entry Delay displays on all
keypads.
When the first digit of a code is entered, the prewarn tone stops at the keypad. If,
within five seconds, a valid user code is not entered or an invalid user code is entered,
the prewarn tone begins sounding again. Fifteen seconds must elapse before entering a
digit silences the prewarn tone again.
The area must be disarmed before the entry delay expires or an alarm is detected. All
Burglary type zones in all areas are delayed along with the Exit zone.
Entry delay times can be from 30 to 250 seconds. Repeat the above for Entry Delay 2 if it
is being used. Default is 30 seconds for Entry Delay 1.
Note: Specific Exit Error operation is based on the Entry Delay used (1 or 2) with an EX
type zone. See Exit Delay.
Exit Delay
Enter the Exit Delay time for all Exit type zones. When the exit delay time starts, all
activity on exit and burglary zones is ig­nored until the exit delay expires. The keypad
displays the Exit Delay time countdown and annunciates the Exit Delay tone at 8 second
intervals until the last 10 seconds when annunciation is at 3 second intervals. The exit
de­lay can be from 45 to 250 sec­onds. Default is 60 seconds.
During Exit Delay, if an exit zone trips, then restores, and trips again, the Exit Delay
timer restarts. This restart can occur only once.
Exit Error Operation: At arming, when an entry/exit zone (EX) is faulted at the end of
the exit delay then one of two sequences occur:
MINUTES:
0 For Entry Delay 1 EX type zones:
MINUTES:
• the bell sounds for the length of time set in Bell Cutoff programming
• the Entry Delay operation starts, requiring code entry to disarm
• if not disarmed, a zone alarm and an Exit Error are sent to the receiver
0 For Entry Delay 2 EX type zones:
• the zone is force armed and a zone force arm message is sent to the receiver
• an Exit Error is sent to the receiver
• the bell sounds for the length of time set in Bell Cutoff programming
Digital Monitoring Products
14
XTL/XTLC Programming Guide
SYSTEM OPTIONS
8.7
CRS ZONE TM:
0
Cross Zone Time
8.8
PWR FAIL HRS:
1
Power Fail Delay
8.9
SWGRBYPS TRIPS:
Enter the time allowed between zone faults. When a zone programmed for cross zoning
faults, the panel begins counting down the Cross-Zone Time entered here. If the same
zone or another cross-zoned zone faults within this time, an alarm report is sent to the
receiver.
If the Cross-Zone Time expires without the second zone fault, only a zone fault report
from the first zone is sent to the receiver. The Cross-Zone Time can be from 4 to 250
seconds in one second increments. Enter 0 (zero) to disable the Cross-Zone Time
feature. See the Appendix.
This option tracks the duration of an AC power failure. The delay time can be from 1 to
9 hours. When the AC power is off for the length of the programmed delay time, an AC
power failure report is sent to the receiver. For example, if the power failure delay is set
for two hours, then the AC power failure report will be sent between 2-3 hours. Entering
a 0 (zero) sends the AC power failure report within 15 seconds.
2
Swinger Bypass Trips
Enter the number of times (1-6) a zone can go into an alarm or trouble condition within
one hour be­fore being auto­matically bypassed. Bypassed zones are auto­matically reset
when the area they are assigned to is disarmed. All 24-hour zones are reset when any
area of the system is dis­armed. A programming Stop operation restores a bypassed zone.
Entering 0 (zero) disables this function. Default is 2.
How it works
The panel hour timer starts at 59 minutes past the hour. If the hour timer expires before
the trip counter is exceeded, the trip counter returns to 0 (zero). If the trip counter is
exceeded before the hour expires, the zone is auto­matically bypassed by the panel. A
Bypass Re­port is sent to the receiver if Bypass Re­ports is YES.
8.10
RST SBYP NOYES
Reset Swinger Bypass
8.11
ZN ACTY HRS:
Zone Activity Hours
8.12
0
When YES is selected, an auto­matically bypassed zone is reset if it remains in a normal
condition for one complete hour after being bypassed. A report of the automatic reset is
sent to the receiver if Bypass Reports has been se­lected as YES. Default is NO.
This option provides supervision of a person living alone for non-activity. Enter the
number of hours, 0 to 9, allowed to elapse without a disarmed zone being tripped before
a message is sent to the receiver. Default is 0 (zero).
When the system is disarmed, the timer begins to countdown the number of hours
programmed. Each time activity occurs, the timer restarts the countdown.
Before the countdown time expires, the keypad sounds a tone and PRESS ANY KEY
displays to allow the user to restart the activity timer. The duration of the tone is the
number of seconds programmed for Entry Delay 2.
Select the SUPV/TRBL receiver option in communication programming to send S93
ALARM: User Activity Not Detected, S94 Alert: Activity Check Enabled, and S95 Alert:
Activity Check Disabled messages.
When an open/close schedule is programmed, the timer only counts down during the
scheduled open period. Also, when a schedule is programmed, if the timer is counting
down and the scheduled open time occurs, the timer resets and begins the countdown
again.
ARM ACTY DAYS:
XTL/XTLC Programming Guide
0
Arm Activity Days
This allows selection of the number of days a countdown timer is set for area arming and
disarming activity. The range for the countdown timer is 00 to 99.
When the timer counts down to zero because of no arming or disarming activity, the
panel sends a “No Arming/Disarming” message to the receiver at 10:00 AM. Each time
an area is armed or disarmed, the timer is restarted. When the countdown timer expires
because of no arming or disarming activity, and a message is sent, the timer does not
restart until a panel reset occurs or an area is armed or disarmed.
The SUPV/TRBL receiver option must be selected in communication programming for the
message to be sent.
Digital Monitoring Products
15
SYSTEM OPTIONS
8.13
TIME CHG NO YES
HRS FROM GMT:
GMT
0
1
2
3
4
5
6
7
8
9
10
11
12
Time Zone Changes
This option allows the panel to request automatic time changes from the DMP SCS-1R
Receiver. For the receiver to send time changes, it must be programmed to send time
changes and must be receiving time change updates from the host automation computer
at least every 24 hours. Default is YES.
6 When time zone is programmed YES, enter the number (0-23) that indicates the
Greenwich Time zone (GMT) where the panel is located. The default is 6. See table for
GMT values.
City/Time Zone
GMT
London, Monrovia, Lisbon, Dublin, Casablanca, Edinburgh
Cape Verde Island, Azores
Mid-Atlantic, Fernando de Noronha
Buenos Aires, Georgetown, Brasilia, Rio de Janeiro
Atlantic Time (Canada), Caracas, La Paz, Santiago
Eastern Time (US, Canada) Bogota, Lima, Arequipa
Central Time (US, Canada), Mexico City, Saskatchewan
Mountain Time (US, Canada), Edmonton
Pacific Time (US, Canada), Tijuana
Alaska
Hawaii
Midway Island, Samoa
Fiji, Marshall Island, Wellington, Auckland, Kwajalein, Kamchatka
8.14
TIME DSP NO YES
Time Display
8.15
HOUSE CODE:
House Code
-
13
14
15
16
17
18
19
20
21
22
23
City/Time Zone
New Cadelonia
Guam, Sydney
Tokyo, Seoul
Hong Kong, Singapore
Bangkok, Hanoi
Dhaka, Almaty
Islamabad, Karachi
Abu Dhabi, Kazan
Moscow, Bagdad
Eastern Europe
Rome, Paris, Berlin
YES allows the keypad to display the time and day in the Status List. When NO is
selected, time and day of the week are not displayed.
A Wireless House Code between 1 and 50 is pre-programmed at the factory. To change
the house code, press a top row select key. Enter a House Code from 1 to 50 and press
the CMD button. The XTL/XTLC automatically programs the house code into the wireless
transmitters when the unique transmitter serial number is programmed into the panel.
See Wireless programming in Zone Information. The house code identifies the panel,
receiver, and transmitters to each other. When operating, the receiver listens for
transmissions that have the programmed house code and transmitter serial number.
8.15.1 DET JAMNG NO YES Detect Wireless Jamming
When enabled and the receiver detects jamming, a trouble or alarm message is sent to
the receiver and displays in the Status List. Select YES to enable jamming messages to
display in the Status List. Select NO to disable jamming messages. Default is NO.
8.15.2 ANY DAY MIN
WLS AUDIBLE: DAY
8.16
KPD PANCS NO YES
Digital Monitoring Products
16
Wireless Audible Annunciation
Press any top row key to select the keypad buzzer annunciation method for wireless low
battery and missing messages.
• Select ANY to enable annunciation anytime.
• Select DAY to enable annunciation except during sleeping hours (9 PM to 9 AM).
• Select MIN (minimum) to annunciate only Fire zones during daytime hours (9 AM to
9 PM). Default is DAY.
Enable Keypad Panic Keys
This option allows the two-button panic key operation selected at a keypad to send the
Panic, Emergency, or Fire message to the central station receiver. Select YES to enable
the two-button panic operation. To disable the two-button panic operation, select NO.
Default is YES.
XTL/XTLC Programming Guide
SYSTEM OPTIONS
8.17
8.18
OCCUPIED PREMISE
NO YES
Occupied Premises
Select YES to allow the panel to automatically disarm the interior area(s) when arming
all areas and a perimeter zone is not tripped during the exit delay.
This False Alarm Reduction feature keeps a user from arming the entire system when
they do not exit and remain in the premise. Select NO to not automatically disarm
interior area(s). Default is YES.
Use False Alarm Question
USE FALSE ALARM
QUESTION? NO YES Select YES to display IS THIS A FALSE ALARM? NO YES at the keypad in place of CANCEL
VERIFY when a burglar alarm occurs. This operates for ALL/PERIM and HOME/SLEEP/
AWAY arming systems. Default is YES.
8.19
ENTER WEATHER
ZIP CODE:
0
XTL/XTLC Programming Guide
Weather Zip Code
This option allows local U.S.A. weather updates to display in the Status List on the
keypad. Enter the zip code of the user at this option. When no number is entered
weather conditions are not displayed. Default is 0 (zero).
Digital Monitoring Products
17
BELL OPTIONS
Bell Options
9.1
Bell Options
BELL OPTIONS
This section allows you to program the panel bell output functions. If using the Model
1135 or 1135DB Wireless Siren, the Trip with Panel Bell option should be selected in the
Output Information programming for the siren.
9.2
BELL CUTOFF:
9.3
BELL TEST NOYES
5
Bell Cutoff Time
Enter the maximum time from 1 to 15 minutes that a wireless output remains on. If the
output is manually silenced or the system is disarmed, the cutoff time is reset. Default is
5.
Automatic Bell Test
When YES is selected, the 1135 wireless siren is turned on for two seconds when all
areas in the system are armed. The Bell Test only occurs when the areas are armed from
a keypad. Arming performed from an Arming zone or remotely from Remote Link™ does
not activate the Bell Test.
Closing Wait operation
When Bell Test is set to YES, the closing wait function also operates. Closing Wait
provides a delay time before a monitored system arms until the panel receives an
acknowledgment of the closing report from the central station receiver. During the
delay, the keypad displays ONE MOMENT . . . Once the closing is acknowledged,
the keypad buzzes for one second and then displays the ALL SYSTEM ON message. If
communication fails, the message LOCAL ALARM ONLY appears.
9.4
BELL OUTPUT:
0
Bell Output
Enter the output number (31-34, 41-44) for an 1116 or 1117 wireless output when
needed to follow the on and off condition of the bell action. Enter 0 (zero) to disable.
Note: When BELL ACTION below is set to T for Temporal Code 3, this Bell Output action
will be Pulse for wired outputs 1-4, wireless outputs 31-34 and 41-44.
9.5
Bell Action
BELL ACTION . . .
This defines the type of Bell Action from zone alarms that will occur. Trouble conditions
do not activate Bell Action. There are seven zone types you can program individually for
Bell Output. To provide a steady Bell Output, enter S. For a pulsed output, enter P. For
a Temporal Code 3 output, enter T and for no wireless zone, enter N.
FIRE TYPE: P
9.5.1Fire
Defines Bell Action for Fire Type Zones. The default is set at P.
9.5.2
BURGLARY TYPE:
S
Burglary
Defines Bell Action for Burglary Type Zones. The default is set at S.
SUPRVSRYTYPE: N
9.5.3Supervisory
Defines Bell Action for Supervisory Type Zones. The default is set at N.
PANIC TYPE: N
9.5.4Panic
Defines Bell Action for Panic Type Zones. The default is set at N.
EMERGNCY TYPE: N
9.5.5Emergency
Defines Bell Action for Emergency Type Zones. The default is set at N.
9.5.6
AUXLRY 1 TYPE: N
9.5.7
AUXLRY 2 TYPE: N
Auxiliary 1
Defines Bell Action for Auxiliary 1 Type Zones. The default is set at N.
Digital Monitoring Products
18
Auxiliary 2
Defines Bell Action for Auxiliary 2 Type Zones. The default is set at N.
XTL/XTLC Programming Guide
OUTPUT OPTIONS
10.1
10.2 Output Options
Output Options
OUTPUT OPTIONS
COM FAIL OUT:
This section allows you to program output options for the 1116 and 1117 wireless
outputs.
Select from the following output numbers:
• 31 to 34
• 41 to 44
• F01 to F20 (To Activate Z-Wave Favorites)
0
Communication Failure Output
This output/Favorite turns on when the panel fails to communicate with the receiver
after eight successive attempts. Enter 0 (zero) to disable this output.
Note: To turn off the Communication Failure Output, disarm the panel or turn the
output off using the User Menu Outputs On/Off function.
10.3 FIRE ALR OUT:
0
Fire Alarm Output
10.4
PANC ALM OUT:
0
Panic Alarm Output
This output/Favorite turns on any time a fire type zone is placed in alarm. The output
turns off using the Sensor Reset option when no additional fire type zones are in alarm.
Enter 0 (zero) to disable this output.
This output/Favorite turns on any time a Panic Zone (PN) is placed in alarm. The output
turns off using the Sensor Reset option once all Panic Zones are restored. Enter 0 (zero)
to disable this output.
If a wireless ouput is programmed, the panel sends the Panic Test Cadence or the Panic
Alarm Cadence to the output when a Panic Test is performed or a Panic Zone is placed in
alarm.
10.5
ENTRY
10.6
BEGIN EXIT:
OUT:
0
0
Entry Output
This output/Favorite turns on at the start of the entry delay time. The output turns off
when the area disarms or the entry delay time expires. Enter 0 (zero) to disable.
Begin Exit Output
This output/Favorite turns on any time an exit delay time starts. The output turns off
when the system arms or when the arming has been stopped. Enter 0 (zero) to disable.
10.7
END EXIT:
End Exit Output
0
This output/Favorite turns on any time an exit delay time ends. The output turns off
when the system disarms. Enter 0 (zero) to disable.
10.8
ARMED
OUT:
0
Armed Output
This output/Favorite turns on any time an area of the system is armed. The output turns
off when the system completely disarms. Enter 0 (zero) to disable this output.
Favorites:
For a Home/Away system:
• When the system is armed AWAY, the programmed Favorite activates.
• When the system is armed SLEEP, the programmed Favorite plus 1 is activated.
For example, If the Armed Output is F05, F06 activates when Sleep is armed.
• When the system is armed HOME, the programmed Favorite plus 2 is activated.
For example, If the Armed Output is F05, F07 activates when Home is armed.
For an All/Perimeter system:
• When the system is armed ALL, the programmed Favorite activates.
• When the system is armed PERIMETER, the programmed Favorite plus 1 is
activated.
For example, If the Armed Output is F05, F06 activates when Perimeter is armed.
For an Area system:
• When any area of the system is armed, the programmed Favorite activates.
XTL/XTLC Programming Guide
Digital Monitoring Products
19
OUTPUT OPTIONS
10.9
DISARMEDOUT:
0
Disarmed Output
This output/Favorite turns on when all areas of the panel are disarmed. The output
turns off when an area is armed.
10.10 BURGLARYOUT:
0
Burglary Output
This output/Favorite turns on any time a burglary zone goes into alarm. The output
turns off when the area in which the alarm occurred disarms and no other burglary zones
are in alarm. Enter 0 (zero) to disable this output.
10.11 READY
OUT:
0
Ready Output
This output/Favorite turns on whenever all disarmed zones are in a normal state. The
output turns off when any disarmed zone is in a bad state. Enter 0 (zero) to disable.
10.12 ARM-ALARM OUT: 0 Arm-Alarm Output
Enter the output/Favorite to turn on steady when any area of the system is armed. If
an alarm occurs causing the keypads to turn Red, this output pulses and continues to
pulse for approximately three (3) minutes after the panel is disarmed. Enter 0 (zero) to
disable.
Wireless Outputs
• The Arm-Alarm Output is compatible with the Model 1117 Wireless LED
Annunciator and the Model 1116 Wireless Relay Output connected to a Model 572
Indicator LED.
• When the Model 1117 is battery operated, the LED is off when the system is
armed to conserve battery life. If an alarm occurs, the output flashes quickly.
• When using the Model 1116 connected to a Model 572, the LED is on when the
system is armed. If an alarm occurs, the output pulses.
• To operate the Arm-Alarm output within one second, program a fast response
number from 41 to 44. Fast response operation reduces overall wireless output
battery life.
• To operate the Arm-Alarm output within 15 seconds, program a slow response
number from 31 to 34. Slow response operation increases overall wireless output
battery life.
10.13 HEAT SAVER
Heat Saver Temperature
TEMPERATURE:0 Enter the desired temperature setting for all Z-Wave thermostats when the system
is armed ALL or AWAY. When the system is disarmed the thermostats return to their
previous settings. The range is 55-95 degrees. Enter 0 (zero) to disable.
10.14 COOL SAVER
Cool Saver Temperature
TEMPERATURE:0 Enter the desired temperature setting for all Z-Wave thermostats when the system
is armed ALL or AWAY. When the system is disarmed the thermostats return to their
previous settings. The range is 55-95 degrees. Enter 0 (zero) to disable.
Digital Monitoring Products
20
XTL/XTLC Programming Guide
OUTPUT INFORMATION
Output Information
11.1
11.2
OUTPUT INFO
Output Information
This section allows you to program and name wireless outputs into the panel.
OUTPUT NO: -
Output Number
AREA NO: -
Note: Addresses 31 to 34 and 41 to 44 are available for wireless outputs, wireless zones,
Enter an output number. Select from the following output numbers:
• 31 to 34 — Slow response time* wireless outputs (activate within 15 seconds)
• 41 to 44 — Fast response time* wireless outputs (activate within 1 second)
INT PERIM or wireless key fob zones and can only be assigned to one device.
* UNUSED *
* The response time of a wireless output is the time it takes for a wireless output to
activate once the panel event occurs. You determine whether a wireless output is a slow
or fast response based on the output number assigned. A slow response output number
extends battery life, but response time may be up to 15 seconds. A fast response output
number responds within 1 second, but reduces battery life. Refer to the specific wireless
output installation guide to determine battery life.
* UNUSED *
Output Name
INT
11.3
BDRM
PERIM
This section allows you to define a 16 character alphanumeric name for any wireless
output.
An output that is not part of the system must be marked *UNUSED*. To mark an output
unused, de­lete the old name by pressing any Select key, then press the COMMAND key.
The pro­grammer auto­matically pro­grams the name as * UNUSED *.
11.4
11.5
Serial Number
SERIAL#: -
Enter the eight-digit serial number found on the wireless device.
ALREADY USED: ZXX
This message displays when the serial number is already programmed for another output
or zone. The programmed output or zone number displays.
SUPRVSN TIME: 240
Supervision Time
Press any top row key to select the supervision time required for the wireless output.
Press COMMAND to accept the default time. Default is 240 minutes.
0
3
60 240 Select the required number of minutes. The transmitter must check in at least
once during this time or a missing condition is indicated for that zone. 1100 Series
transmitters automatically check in based on the supervision time selected for the
wireless zone, no additional programming is needed. Zero (0) indicates an unsupervised
transmitter.
The 3 minute supervision time is only available if using an 1135 Wireless Siren.
Note: When the panel is reset, a receiver is installed or powered down and powered up,
or programming is complete, the supervision timer restarts for all wireless outputs.
11.6
TRIP WITH PANEL
BELL NO YES
XTL/XTLC Programming Guide
Trip with Panel Bell Option
This option displays when the wireless device is an 1135 wireless siren. Select YES to
have the 1135 wireless siren follow the panel bell output. Default is YES.
Digital Monitoring Products
21
AREA INFORMATION
Area Information
12.1
AREA INFORMATION
Area Information
This section allows you to assign functions to individual areas for XTL/XTLC panels.
All non-24-hour zones must be assigned to an active area. See the section on Zone
Information.
Activate an area by assigning it a name. A name is given to each active area to assist the
user during arming and disarming.
12.2
Area Number
AREA NO: -
Enter the number of the area to program. In an area system, select from areas 1 to 6.
INT PERIM In an All/Perimeter system, select INTerior or PERIMeter. In a Home/Away system, select
INT BDRM PERIM INTerior, BDRM, or PERIMeter.
12.3
Area Name
* UNUSED *
In an area system, enter up to 16 characters for the area name. Only those areas given
names can have zones assigned to them. All others are marked *UNUSED*. Refer to the
Entering Alpha Characters section.
To add an area name to the system, press any Select key and then enter up to 16
characters for the new name. Press COMMAND to continue.
To mark an active area as unused, delete the old name by pressing any Select key then
press the COMMAND key. The panel automatically sets the name as *UNUSED*. If you
have already Initialized the panel, all areas will be marked as *UNUSED*. See section
2.3.
12.4
AUTO ARM NOYES
Automatic Arming
Select YES to allow this area to arm automatically according to the opening and closing
schedule.
If Closing Check is selected as YES, the automatic arming does not take place until the
expiration of a 10-minute Closing Check delay. If the area has been disarmed outside a
schedule, the Closing Check delay occurs one hour after the area is disarmed.
At arming, faulted zones are handled according to the option selected in Bad Zones. If
a Closing report is sent, the user number is indicated as SCH on the SCS-1R Receiver.
Select NO to disable automatic arming for this area. Default is NO.
Note: For ANSI/SIA CP-01 installations, Automatic Arming cannot be used for arming.
12.4.1 BAD ZONES: BYP Bad Zones
BYP FORC
REF At the time of automatic arming, some zones in the area may not be in a normal
condition. This option allows you to program the panel’s response to these bad zones.
This option is not displayed if AUTO ARM is NO.
BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if Bypass
Reports has been selected as YES. See the Bypass Reports section. The report indicates
SCH as the user number.
FORC - All bad zones are force armed. Zones force armed in a bad condition are capable
of restoring into the system and reporting alarms if tripped. A report of the force arm is
sent if Bypass Reports is YES. See the Bypass Reports section. The report indicates the
user number as SCH.
REF - The automatic arming is refused and no arming takes place. A No Closing report
is sent to the receiver regardless of the Closing Check selection. See the XTL/XTLC
Programming Sheets.
Note: For listed installations, set Bad Zones to REF.
12.5
AUTO DIS NOYES
Automatic Disarming
NO disables automatic disarming by schedule for this area. Select YES to allow this area
to automatically disarm according to a schedule. If an Opening report is sent to the
receiver, the user number is indicated as SCH.
Note: For ANSI/SIA CP-01 installations, Automatic Disarming cannot be used.
Digital Monitoring Products
22
XTL/XTLC Programming Guide
ZONE INFORMATION
Zone Information
13.1
13.2
ZONE INFORMATION
Zone Information
This allows you to define the operation of each protection zone used in the system.
Zone Number
ZONE NO: -
Zone numbers on the XTL/XTLC panel default to the following settings. The settings can
be changed as described in the following sections. Zones 31-34 can be wireless zones,
key fobs or slow outputs. Zones 41-44 can be wireless zones, key fobs, or fast outputs.
Zone Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
31
32
33
34
41
42
43
44
13.3
KEYFOB
NOYES
XTL/XTLC Programming Guide
Zone Name
FRONT DOOR
BACK DOOR
INTERIOR DOOR
UPSTAIRS DOOR
BASEMENT DOOR
GARAGE DOOR
WAREHOUSE DOOR
SHIPPING DOOR
BREAKROOM DOOR
STOCKROOM DOOR
FRONT MOTION
BACK MOTION
INTERIOR MOTION
UPSTAIRS MOTION
BASEMENT MOTION
GARAGE MOTION
GLASSBREAK
WATER DETECTOR
LOW TEMPERATURE
SMOKE DETECTOR
FRONT SMOKE
BACK SMOKE
INTERIOR SMOKE
UPSTAIRS SMOKE
BASEMENT SMOKE
GARAGE SMOKE
WAREHOUSE SMOKE
SHIPPING SMOKE
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
ALARM SOUNDER 1
ALARM SOUNDER 2
ALARM SOUNDER 3
ARM/ALARM LIGHT
Zone Type
EX
EX
NT
EX
EX
EX
EX
EX
NT
NT
NT
NT
NT
NT
NT
NT
NT
AUX 1
AUX 1
FI
FI
FI
FI
FI
FI
FI
FI
FI
Area Assignment
PERIM
PERIM
INT
PERIM
PERIM
PERIM
PERIM
PERIM
INT
INT
INT
INT
INT
INT
INT
INT
INT
INT
INT
Key Fob
Select YES to program an 1100 Series Key Fob for zones 31-34 or 41-44. When YES is
selected, programming continues at the 1100 Series Key Fobs Section. Default is NO.
Digital Monitoring Products
23
ZONE INFORMATION
13.4
* DEFAULT NAME *
Zone Name
Press any Select key to display the default zone name. To change the default zone name,
press any Select key to clear name. Enter up to 16 characters for the new zone name.
This name is displayed at the keypads when the zone is bad or viewed in Display Events.
The zone name is also sent to the receiver as part of a zone event report.
A zone that is not part of the system must be marked *UNUSED*. To mark a zone unused,
de­lete the old name by pressing any Select key, then press the COMMAND key. The pro­
grammer auto­matically pro­grams the name as * UNUSED *. If you selected ZONES? NO
YES to clear the panel’s memory during Initialization, the zones will already be marked *
UNUSED *. See the Initialization section.
13.5
ZONE TYPE: -
Zone Type
-- NTDYEX
Blank, Night, Day, or Exit. Press COMMAND to display additional zone types.
The Zone Type defines the panel’s response to the zone being opened or shorted. Refer
to the Appendix for zone type defaults and descriptions.
When you assign a Zone Type to a zone, responses are made automatically for the zone.
There are 11 Zone Types to choose from including Blank. The func­tional details of each
response are described in Zone Type Defaults in the Appendix.
To change the Zone Type, press any Select key. The display lists the four Zone Types
shown below. When the Zone Type you want to select displays, press the Select key
below the name.
FI PNEMSV Fire, Panic, Emergency, or Supervisory. Press COMMAND to display additional zone types.
A1A2 FVAR Auxiliary 1, Auxiliary 2, Fire Verify, or Arming. Press the Back Arrow key to display the
13.6
previous zone types.
If you select Blank, Night, Day, Exit, Auxiliary 1, or Auxiliary 2 as the Zone Type, the
zone must be assigned to an area. If you select Fire, Panic, Emergency, or Supervisory as
the Zone Type, these are 24-hour zones that are always armed and no area assignment is
needed. Press COMMAND to continue.
Refer to the Appendix for zone type specifications and descriptions.
Area Assignment
AREA: INT
To change the default area, press any Select key.
PERIM For Area systems, enter the area number from 1 to 6 where this zone is being assigned.
For All/Perimeter systems, choose INTERIOR or PERIMETER.
INT BDRM PERIM For Home/Away systems, choose INTERIOR, PERIMETER, or BEDROOMS.
•
•
13.7
•
INT (Interior) - Assigns the zone to area 2, Interior.
BDRM (Bedroom)- Assigns the zone to area 3, Bedrooms. This option is only
displayed in Home/Away systems.
PERIM (Perimeter) - Assigns the zone to area 1, Perimeter.
Arming Zone Assignment
AREA:
For Area systems, this option specifies the areas to be armed by the Arming Type zone.
Press the appropriate number keys on the keypad to assign areas 1 to 6. When disarmed,
all programmed areas are disarmed.
ARM AREA:PERIM
PERIM
ALL Perimeter/All - Specify whether the arming zone arms just the Perimeter (PERIM) or the
HOME SLEEP AWAY
Digital Monitoring Products
24
For All/Perimeter systems, choose PERIM or ALL. For Home/Away systems, choose
HOME, SLEEP, or AWAY.
Perimeter and Interior areas (ALL) for All/Perimeter systems. When disarming, all areas
are disarmed.
HOME/SLEEP/AWAY - Specify whether the arming zone arms the Perimeter (HOME), the
Perimeter and Interior (SLEEP), or all three areas (AWAY). When disarming, all areas are
disarmed.
Arming zone operation
If a bad (faulted) Priority zone is in the area being armed by an Arming zone, the arming
is stopped. If there are no Priority zones, or they are all in a normal condition, the
following applies:
When a non-Priority zone is bad when an area is armed with a keyswitch on an Arming
zone, the arming is delayed for five seconds. If, during the five-second delay, the
keyswitch is turned to disarm, the arming stops. If the keyswitch is held in the arming
position for the full five seconds, the bad zone is force armed and the area is armed.
XTL/XTLC Programming Guide
ZONE INFORMATION
The ability to stop the arming does not apply if a wireless arming device is being used.
Refer to the Appendix.
Note: Arming from a zone, cell, or Remote Link is not affected by this operation.
13.7.1Style
STYLE:
TOGGLE
This option specifies the style for the arming/disarming operation. The default for
STYLE: is TGL (toggle). Pressing any Select key displays the STYLE options. To view
more style options press the command key. The following is a description of the action
for each option condition.
TGLARM DISSTEP TGL (Toggle) - When the zone changes from normal to shorted, the programmed areas
toggle between the armed or disarmed condition. When restored to normal, no action
occurs. When the zone is opened from a normal (disarmed) state, a trouble is reported.
When opened from a shorted (armed) state, an alarm is reported and the zone is disabled
until you disarm the area(s) from either a keypad or Remote Link™ computer.
ARM - When the zone is shorted, the programmed areas are armed. When restored to
normal, no action occurs. When the zone is opened from a normal (disarmed) state, a
trouble is reported. When opened from a shorted (armed) state, an alarm is reported.
DIS (Disarm) - When programmed as an Area system, a short will disarm the programmed
areas. When programmed as a ALL/PERIM or HOME/AWAY system, a short will disarm
ALL areas. When restored to normal, no action occurs. When the zone is opened from a
normal (disarmed) state, a trouble is reported.
STEP - When programmed as an area system, a short will arm the areas and beep the
keypads once. When programmed as ALL/PERIM or HOME/AWAY, on the first short HOME
will arm and beep the keypad once. On the second short, SLEEP will arm and beep the
keypads twice. On the third short, AWAY will arm and beep the keypad three times. A
normal condition will cause no action. An open condition will disarm the programmed
areas and beep the keypads for one second.
Note: This arming style is designed for wireless arming pendants. When using a arming/
disarming keyswitch, locate the keyswitch within the protected area.
MNT
DMP Wireless
13.9
SERIAL #: -
MNT (Maintain) - When the zone is shorted, the programmed areas are armed. When
restored to normal, the programmed areas are disarmed and any alarm bells are
silenced. When the zone is opened from a normal (disarmed) state, a trouble is
reported. If opened from a shorted (armed) state, an alarm is reported and the zone is
disabled until you disarm the area(s) from either a keypad or Remote Link™ computer.
For an 1100 Series Key Fob see the 1100 Series Wireless Key Fob programming section.
NOTE: All wireless programming is stored in the XTL/XTLC panel. Each time the panel powers up, when the
programmer STOP routine is selected or the panel is reset, the wireless receiver memory refresh could take up
to 45 seconds to complete depending on the number of wireless zones programmed and the Red LED remains on
during this time. Normal wireless receiver operation is inhibited during the memory refresh period.
Serial Number Entry
Enter the eight digit serial number, including leading zeros, found on the wireless
device.
13.10Contact
CONTACT: INTERNAL
This option displays if the serial number entered is for an 1101, 1103, or 1105 Universal
Transmitter or 1114 Wireless Four-Zone Expander. Press any top row key to select the
contact.
INTEXT
This option displays when programming an 1101, 1103, or 1105 Universal Transmitter.
Select INT to use the internal reed switch contacts. Select EXT to connect an external
device to the 1101, 1103, or 1105 terminal block. Default is INTERNAL.
By allowing both of the transmitter contacts (INT and EXT) to be used at the same time,
two zones may be programmed from one transmitter. When using multiple contacts, you
must use consecutive zone numbers.
For example, program transmitter serial number 01345678 as Zone 11 with an INT
contact type and Zone 12 with an EXT contact type. The same serial number is used for
both zones.
XTL/XTLC Programming Guide
Digital Monitoring Products
25
ZONE INFORMATION
CONTACT: x
1
This option displays when programming an 1114 zone expander which provides four input
contacts. Press any top row key to select the contact. Default is Contact 1.
2
3
4 Select the contact number to program. The same transmitter serial number is used for
all four contacts. When using the contacts, you must use consecutive zone numbers.
For example, use serial number 08345678 to program Contact 1 for Zone 21, Contact 2
for Zone 22, Contact 3 for zone 23, and Contact 4 for zone 24.
A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.
ALREADY USED
Zxx This message displays when the Contact is already programmed for another zone. The
programmed zone number displays.
NORM OPEN NO YES The Normally Open option only displays when EXT is selected as the Contact type. For
external devices connected to the 1101 terminal block, select NO to use normally closed
(N/C) contacts. Select YES to use normally open (N/O) contacts. Default is NO.
13.10.1SUPRVSN TIME:
XX
Supervision Time
Press any top row key to select the supervision time required for the wireless zone. Press
COMMAND to accept the default time. Default is 240 minutes.
0 360
240
Select the required number of minutes. The transmitter must check in at least
once during this time or a missing condition is indicated for that zone. 1100 Series
transmitters automatically checkin based on the supervision time selected for the
wireless zone, no additional programming is needed. If two zones share the same
transmitter, the last programmed supervision time is stored as the supervision time for
both zones. Zero (0) indicates an unsupervised transmitter.
The 3 minute supervision time is only available for zone types of Fire (FI), Fire Verify
(FV), and Supervisory (SV).
Note: When the panel is reset or a receiver is installed or powered down and powered
up, the supervision timer restarts for all wireless zones.
13.10.2LED OPER NO YES LED Operation
This only displays when programming a panic or pendant transmitter. Select YES to turn
a panic or pendant LED on during normal operation. Select NO to turn the LED off during
normal operation. The LED always operates on all transmitters when the transmitter
case is open and the tamper is faulted. Default is YES.
13.10.3 DISARM DISABLE
YES Select YES to disable the zone tripped message from an 1103 Universal Transmitter
(Version 107 or higher software) or 1126/1127 PIRs during the disarmed period. When
disarmed, the transmitter or PIR only sends supervision, tamper, and low battery
messages to extend transmitter battery life. For 1103 Transmitters, a zone tripped
message is sent if the zone remains tripped for 20 seconds. Select NO to always send
zone tripped messages in addition to supervision, tamper, and low battery.
Default is YES.
13.10.4 WIRELESS PIR
PULSE COUNT:
13.10.5 WIRELESS PIR
SENSITIVITY:
13.10.6NEXT ZN
Disarm/Disable
Wireless PIR Pulse Count
4 Select the number of infrared pulse counts (2 or 4) the PIR will use before sending a
short message. The first infrared pulse starts a timer and count. If no additional infrared
pulses occur in 25 seconds, the timer and count are reset. Default is 4.
Wireless PIR Sensitivity
LOW
NO YES
Digital Monitoring Products
26
Select the sensitivity setting for the PIR. Selecting LOW sets the PIR to operate at
75% sensitivity for installations in harsh environments. Selecting HIGH sets the PIR to
maximum sensitivity. Default is LOW.
Next Zone
Select YES to return to the ZONE NO: - option to program a new zone. Select NO to
display the Alarm Action option.
XTL/XTLC Programming Guide
ZONE INFORMATION
13.11 Series Key Fobs
Only zones 31‑34 or 41-44 can be programmed as 1100 Series Key Fob zones. Refer to the 1100 Series Key Fob
Programming Sheet (LT-0706) supplied panel and the 1100 Series Key Fob Install Guide (LT-0703) as needed.
To operate arming and disarming properly, the Key Fob should be assigned to a User Number with
appropriate area assignments, however, the User Number does not have to exist at the time the Key Fob is
programmed. The User Number can be added at the User Menu later by the User.
The following programming continues from when Key Fob YES is selected.
13.11.1 KF USER NO:
Key Fob User Number
Enter the User Number used to identify the key fob user and their arming and disarming
authority. Default is blank.
— User number range: 1 to 30
Displays when the User Number entered does not exist in User Code programming. The
key fob can be added, but the user must eventually be added to cause the key fob to
operate.
NOT IN USE
13.11.2SERIAL #: -
Key Fob Serial Number
Enter the eight-digit serial number found on the wireless device.
ALREADY USED
Zxx Displays when the serial number is already programmed. The programmed zone number
displays.
13.11.3 SUPRVSN TIME:
0
Key Fob Supervision Time
Press any top row key to select the supervision time required for the key fob zone. Press
COMMAND to accept the default time. Default is 0.
0 60240 Press the Select key under the required number of minutes. The key fob must check
in at least once during this time or a missing condition is indicated for that zone. 1100
Series key fobs automatically checkin based on the supervision time selected for the
wireless zone, no additional programming is needed. Zero (0) indicates an unsupervised
transmitter.
Note: When the panel is reset or a receiver is installed or powered down and powered
up, the supervision timer restarts for all wireless zones.
13.11.4 BUTTONS: 4
Number of Key Fob Buttons
Enter the number of buttons (1, 2, or 4) on the key fob being programmed. Default is
four buttons.
Note: If the key fob is a one-button model, programming continues at the Button Action
section. Default button assignment for one-button key fobs is a Panic Alarm (PN) with no
output assigned.
13.11.5 TOPBTM LFT RGT Key Fob Button Selection (Four Buttons)
This option only displays if the key fob being programmed is a four‑button model. Press
the Select key under the key fob button to program. The following list identifies the
default button assignments:
TOP Arming with areas 1, 2, and 3 assigned
BTM Disarming with areas 1, 2, and 3 assigned
LFT
Panic Alarm (PN) with no output assigned
RGT Arming with Area 1 assigned
13.11.6 TOPBTM
12.11.7 ACTION:
Key Fob Button Selection (Two Buttons)
This option only displays if the key fob being programmed is a two-button model. Press
the Select key under the key fob button to program. The following list identifies the
default button assignments:
TOP Arming with areas 1, 2, and 3 assigned
BTMDisarming with areas 1, 2, and 3 assigned
X
XXXXXX
XTL/XTLC Programming Guide
Button Action
This option specifies the Button Action for an individual key fob button. The default
action for the button selected is displayed. Press any Select key to display the Button
Digital Monitoring Products
27
ZONE INFORMATION
Action options. To view more options press the COMMAND key.
ARMDIS TGL STA ARM (Arm) - Arms selected areas and force arms bad zones.
DIS (Disarm) - Disarms selected areas.
TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad zones
when arming.
STA (Status) - Causes the key fob LED to indicate the arm/disarm status of the system.
PN PN2
EM EM2 PN (Panic) - Triggers a Panic zone type alarm with no restoral.
PN2 (Panic 2) - Triggers a Panic zone type alarm with no restoral when pressed
simultaneously with any other Panic 2 button. No action occurs when pressed alone.
EM (Emerg) - Triggers an Emergency zone type alarm with no restoral.
EM2 (Emerg 2) - Triggers an Emergency zone type alarm with no restoral when pressed
simultaneously with any other Emergency 2 button. No action occurs when pressed
alone.
OUT RST
UN
OUT (Output) - Causes an output to turn on steady, pulse, momentary, toggle or off.
RST (Sensor Reset) - Causes the panel to perform a standard Sensor Reset.
UN (Unused) - The button is not used and performs no action.
13.11.8 PRESS TIME: XXXXX Button Press Time
This option specifies the amount of time (SHORT or LONG) the user must press the
button before the key fob sends a message to the wireless receiver. The default press
time displays. Press any Select key to set the Button Press Time for Arm, Disarm, Toggle,
Status, Output, and Sensor Reset.
Note: The Button Press Time is not programmable on Panic (PN or PN2), Emergency (EM
or EM2) or Unused (UN) zones. For those zones the button press time is always two (2)
seconds.
SHORT LONG SHORT - Press the button for one-half (1/2) second to send the message to the wireless
receiver.
LONG - Press the button for two (2) seconds to send the message to the wireless
receiver.
13.11.9 AREA: 1 2 3 4 5 6
Arm/Disarm Area Selection
For Area systems, enter the areas 1 to 6, to be armed/disarmed by the Key Fob button
being programmed.
ARM AREAS: PERIM This specifies the area to be armed by the Key Fob button being programmed.
For All/Perimeter systems, choose PERIM or ALL.
For Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.
After selecting the areas, for one-button key fobs the Zone No.: option displays. For
two-button or four-button key fobs, the Key Fob Button Selection option displays to
program additional buttons.
13.11.10OUTPUT NO: 0
Output Number
13.11.11ACTION:
Output Action
You can specify a wireless output/Favorite to operate when OUT (Output), PN (Panic),
PN2 (Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob Button
Action and the button is pressed. Valid range is 31-34, 41-44, and F01-F20. For an output
turned on by a PN, PN2, EM, or EM2 button action, the output turns off when any area is
disarmed.
To enter an output number, press a top row Select key followed by the output number.
Press the COMMAND key.
This option allows you to define the output action (STD, PLS, MOM, TGL, OFF) for the
selected output number. The default is Steady.
STD PLS MOM TGL STD (Steady) - The output is turned on and remains on.
Digital Monitoring Products
28
XTL/XTLC Programming Guide
ZONE INFORMATION
PLS (Pulse) - The output alternates one second on and one second off.
MOM (Momentary) - The output is turned on only once for one second.
TGL (Toggle) - The output alternates between the on state and off state. Each button
press toggles the output state.
OFF
OFF (Off) - The output is turned off. If programmed, the output was turned on by some
other means such as another button press, a zone action, or a schedule.
Note: When the output is assigned to PN/PN2 or EM/EM2 button action and is turned
on, the output turns off when any area is disarmed.
When the output action is steady, pulse or toggle and the output is turned on, the
output remains on until:
— the output cutoff time expires
— the output is reset from the keypad menu
— toggled off
13.12 ALARM ACTION . . .
Alarm Action
The Alarm Action section allows you to change or confirm the default alarm
characteristics of a zone type.
If you selected the non-24-hour zone type Blank, Night, Day, Exit, Auxiliary 1, or
Auxiliary 2, the Alarm Action programing begins with Disarmed Open.
If you selected the 24-hour zone type Fire, Panic, Emergency, or Supervisory, the Alarm
Action programming begins with Armed Open.
13.13 DISARMED OPEN
Disarmed Open
Defines the action taken by the panel when the zone is opened while the area is
disarmed. There are three actions to define:
• Message to Transmit
• Output/Favorite Number
• Output Action
You must also make these selections for the Disarmed Short, Armed Open, and Armed
Short zone conditions. Press the COMMAND key to continue.
13.13.1MSG: TROUBLE
Message To Transmit
You can send two report types to the receiver: Alarm and Trouble. These are represented
by the characters A and T. Press any Select key to display the zone report options.
ATL - ALARM - Selecting A allows an alarm report to be sent to the receiver and the wireless
siren output to activate according to zone type. See the Bell Action section. The zone
name appears in the panel’s alarmed zones status lists.
TROUBLE - Selecting T allows a trouble report to be sent to the receiver and the zone
name to appear in the panel’s alarmed zones status lists.
LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell output
still activates according to zone type and the zone name appears in the panel’s alarmed
zones status lists.
– (dash) - When you select – , reports are NOT sent to the receiver. The wireless siren
output does not activate and there is no display in the panel’s alarmed zones status list.
Only the programmed Output Number activates.
12.13.2OUTPUT NO: 0
Output Number
You can specify any of the outputs/Favorites on the XTL/XTLC to be activated by a zone
condition. The output/Favorite can be activated regardless of the report to transmit or
whether or not the zone is programmed as local. An output activated by a non‑24‑hour
armed zone is turned off when the zone’s area is disarmed by a user.
To enter an Output Number, press any Select key followed by the output number
31-34, 41-44, or F01-F20. Press the COMMAND key.
XTL/XTLC Programming Guide
Digital Monitoring Products
29
ZONE INFORMATION
13.13.3ACTION:
Output Action
NOYES Entering an Output Number displays this option that allows you to assign an output
action. A description of the available output actions is given below:
STDPLS MOM FOLW STEADY - The output is turned on and remains on until the area is disarmed, an output
cutoff time expires, or the output is reset from the keypad User Menu.
PULSE - The output alternates one second on and one second off until the area is
disarmed, an output cutoff time expires, or the output is reset from the keypad User
Menu.
MOMENTARY - The output is turned on only once for one second.
FOLLOW - The output is turned on and remains on while the zone is in an off normal, or
bad condition. When the zone restores, the output is turned off.
After you have selected the Message To Transmit, the display prompts you for the same
three selections for Disarmed Short, Armed Open, and Armed Short conditions. If the
zone is a 24-hour type, only the Armed Open and Armed Short conditions are displayed.
When you have programmed all of the zone conditions, the Swinger Bypass selection is
then dis­played.
13.14 SWGR BYP NO YES Swinger Bypass
Selecting YES allows the zone to be swinger bypassed by the panel according to the
programming in Swinger Bypass Trips and Reset Swinger Bypass. The Bypassed zone
displays in the keypad Status List. Selecting NO disables swinger bypassing for this zone.
How it works
If within one hour, a zone trips the total number of times as specified in Swinger Bypass
Trips, the panel bypasses it until the following conditions occur; the area in which
the zone is assigned is disarmed, the zone is manually reset through the Bypass Zones
keypad User Menu function, the zone remains normal for one hour and the Reset Swinger
Bypass is YES.
If the zone trips fewer than the specified times within one hour of the first trip, the
bypass trip counter returns to 0 (zero) and the process must be repeated.
A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.
13.15 PREWARN: 12345
13.16 ENTRY DELAY:
Prewarn Address
Option is only shown for an Exit zone.
At the start of the entry delay, all keypad addresses dis­play ENTER CODE:-. If you want
the prewarn to sound at all addresses, leave the default as shown.
To delete an address, press the matching number on the keypad. To disable prewarning
at all keypads, press a top row key to clear the addresses shown. Press the COM­MAND
key when the address selection is com­plete.
Note: The prewarn tone stops at the keypad when the first digit of a user code is
entered. If, within five seconds, a valid user code is not entered or an invalid user code
is entered, the prewarn tone begins sounding again. Fifteen seconds must elapse before
entering a digit silences the prewarn tone again.
1
Entry Delay
Option is only shown for an Exit zone. Select the entry delay timer for this zone. Entry
delay timers 1 and 2 are programmed in Entry Delay in the System Options menu.
13.17 CRS ZONE NOYES Cross Zone
Select YES to enable cross-zoning for this zone. Cross-zoning requires this zone to trip
twice, or this zone and another cross-zoned zone to trip, within a programmed time
before an alarm report is sent to the receiver.
Note: To operate correctly, all cross-zone zones need to be programmed as the same
zone type.
When a cross-zoned zone trips, the Output action assigned to the zone activates. See the
Bell Action section. The cross-zone time specified in System Options begins to count down.
See the Cross-Zone Time section. If another cross-zoned zone in the system faults, or if the
first zone restores and faults again before the cross-zone time expires, the bell turns on
and the panel sends an alarm report.
Digital Monitoring Products
30
XTL/XTLC Programming Guide
ZONE INFORMATION
If no other cross-zoned zone in the system trips before the cross-zone time expires, the
panel sends only a fault report from the first zone to the receiver.
Note: If CRS ZONE is YES, a valid CRS ZN TIME must be programmed in System Options
for this feature to be enabled.
Cross-zoning is not compatible and cannot be enabled for Fire Verify zone types.
13.18Priority
PRIORITY NOYES
Selecting YES allows you to provide additional protection for a zone by requiring it to be
in a normal condition before its assigned area can be armed. A priority zone cannot be
bypassed.
A Priority zone not in a normal condition cannot be armed. If a user attempts to arm
the area, the keypad displays the bad zone name followed by PRIORITY ZONE and the
arming is stopped.
13.19 TRAFFIC COUNT
13.20 ZONE AUDIT DAYS:
13.21 RECEIVER ROUTING
Traffic Count
This option is displayed for NT or EX type zones. Select YES to provide reporting to the
receiver of the number of zone trips while in a disarmed state. The number of trips for
each zone set as traffic count are added together and included with the area closing
message and reported to the central station automation system. Default is NO.
Zone Audit Days
Enter the number of days (0 to 99) allowed to elapse without the zone being tripped
before a fault message is sent. The message is sent to the receiver(s) programmed
to receive Supervisory/Trouble Reports at 10:00 am following the expiration of the
timer. Each time the zone is tripped, the Zone Audit Days timer restarts and begins
to countdown the number of days programmed. After the countdown expires, a fault
message is sent and the Zone Audit Days timer restarts and begins to countdown the
number of days programmed. Available for all zone types except fire and fire verify.
Enter 0 (zero) to disable this function. Default is 0 (zero).
Receiver Routing
This option displays if Zone Type is set for Auxiliary 1 or Auxiliary 2.
Press any top row key to select the Receiver Routing for the selected zone.
• Select NORM to send Alarm and Supv/Trbl messages from this zone to receiver 1 or
receiver 2 as programmed within the receiver.
• Select 1 to send Alarm and Supv/Trbl messages from this zone to receiver 1 only,
regardless of the programming for that receiver.
• Select 2 to send Alarm and Supv/Trbl messages from this zone to receiver 2 only,
regardless of the programming for that receiver.
• Select BOTH to send Alarm and Supv/Trbl messages from this zone to both
receivers, regardless of the programming for either receiver.
13.22 ZONE NO: -
XTL/XTLC Programming Guide
Zone Number
Enter the zone number you want to program next. Return to section 11.1 and follow the
descriptions of each programming option. If all zones are programmed, press the ARROW
key at the ZONE NO: – display to continue.
Digital Monitoring Products
31
STOP
Stop
14.1Stop
STOP
At the STOP option, pressing any Select key allows you to exit the programmer function
of the XTL/XTLC panel. When selected, the panel performs an internal reset and exits
the programmer. The Stop function causes the following conditions to occur:
• All 1100 Series DMP Wireless transmitters are reset to NORMAL
•
The panel’s Status List is CLEARED
During the Stop function, all keypad displays are momentarily disabled for two seconds.
Afterwards, the programming function is terminated and the keypads return to the
Status List display.
SET LOCKOUT CODE
Set Lockout Code
15.1
SET LOCKOUT CODE
Set Lockout Code
Pressing COMMAND at the Stop option displays SET LOCKOUT CODE. This feature allows
you to program a special code that will then be required to gain access to the panel’s
internal Programmer through the keypad.
Changing the Lockout Code
You can change this code at any time to any combination of numbers from 1 to 5 digits
long (1 to 65535). Do not use leading zeros for the lockout code.
1. Press any Select key. The display changes to ENTER CODE: -.
2. Enter a 1- to 5-digit code (do not enter a number higher than 65535). Press
COMMAND.
3. Enter the new Lockout Code again. Press COMMAND. The keypad display changes to
CODE CHANGED.
Once you have changed the code, it is important that you write it down and store it in a
safe place. Lost lockout codes require the panel to be sent back into DMP for repair. You
may cancel a Lockout Code by entering 00000 at the Set Lockout Code command option.
Lockout Code restriction
Do not set a Lockout Code higher than 65535.
Digital Monitoring Products
32
XTL/XTLC Programming Guide
APPENDIX
Appendix
16.1
This section of the XTL/XTLC Programming Guide provides additional zone and system information.
Status List
The Status List is the current status of the system or records of recent system events that display on
alphanumeric keypads. For example, in Home/Away systems you may see the display SYSTEM READY.
If an event were to occur on the system, such as an AC failure, the keypad would also display the AC POWER
-TRBL message. This is a system event that is placed into the Status List to alert the user to a problem with the
system.
Some Status List items remain in the display until manually cleared and some are cleared automatically when
the condition returns to normal. Below is a list of status and event displays the keypad can show in the Status
List:
Description
Must be manually cleared?
Fire and Supervisory zone alarms
Yes - by Sensor Reset
Fire and Supervisory zone troubles
No - clears when zone restores
Burglary zone alarms
No - clears at disarming.
All other zone alarms
No - clears when zone restores
Zone monitor displays
No - clears after approximately 8 minutes
Day zone alerts
No - clears after approximately 8 minutes
System monitor troubles
No - clears when condition restores
(AC and battery trouble)
Armed status display
No
(System On)
Disarmed status displays
No
(System Ready, System Not Ready)
Remote keypad messages
No
(Sent to the keypad by your office or central station)
The highest priority message is displayed on the keypad. When there are multiple items in the list, you can use
the COMMAND or Back Arrow keys to scroll forward or back through the items.
16.2
Transmission Delay
You can set Abort Reports to YES if Opening and Closing reports are not being sent.
If the area where the alarm occurred is disarmed during the Transmit Delay time, only an Abort Report (S45)
message is sent to the receiver. If the area where the alarm occurred is disarmed after the alarm message is
sent to the receiver but before the Bell Cutoff time expires, even if the alarm was silenced, an Alarm Cancelled
(S49) message is sent. The Alarm Cancelled report cannot be disabled.
16.3
False Alarm Reduction
System Recently Armed report
The System Recently Armed report (S78) is sent when a burglary zone goes into alarm within two minutes of the
system being armed.
16.4
Diagnostics Function
The XTL/XTLC panel contains a Diagnostics function that allows you to test the integrity of the CDMA cellular
communication, cellular signal, and email communication. The Diagnostics function also displays the panel
settings. To use Diagnostics, reset the panel, enter the Diagnostics code 2313 (DIAG), and press COMMAND.
Cellular Status
This option tests the individual components of cellular communication. Entry into the Cellular Status (CELL
STATUS) menu will cause each component of the panel’s cellular communication to be tested. The test will
proceed until the first component failure or until all components have been tested with positive results. The
test screen will display after each component and will be displayed for two seconds or until the CMD key has
been pressed.
Cellular Signal Strength (CELL SIGNAL)
-XX dBm This option provides a way to test the cellular signal strength of the nearest tower for
SIGNAL: ▐▐▐▐▐▐▐ the SIM card carrier. Press any top row Select key to display cell signal strength. The X’s
represent the numerical value of the cell signal strength in -dBm. The ▐’s represent the
signal strength 0-7.
XTL/XTLC Programming Guide
Digital Monitoring Products
33
APPENDIX
Cell Roaming Indicator on XTLC
ROAM
-XX dBm
SIGNAL: ▐▐▐▐▐▐▐
The Cellular Signal Strength option in the panel’s Diagnostic menu contains a roaming
indicator. When the XTLC is roaming or not in contact with a Verizon owned tower, ROAM
will be displayed on the top line of the keypad along with the signal strength. To
perform the cellular activation process from a keypad, the panel MUST be in contact
with a Verizon owned tower. If the cellular communicator is in contact with a tower
owned by another network, ROAM and the signal strength displays, but activation cannot
be completed. This feature can be used as a diagnostic tool to troubleshoot activation
issues.
Cellular Activation
Activation for XTL
1. In Remote Link panel communication programming, select
Cellular Network as the Communication Type and select the
Activate button. See Figure 4.
2. In the Activate SIM/MEID window, enter the SIM number, found on
the SIM card.
3. Select the rate plan for the XTL. See Figure 5.
4. Select the Activate button at the bottom of the
window.
Activation for XTLC
Figure 4: Remote Link Activation
1. In Remote Link panel communication programming,
select Cellular Network as the Communication Type
and select the Activate button. See Figure 4.
A.In the Activate SIM/MEID window, enter the
MEID number, found on the XTLC label.
B.Select the rate plan for the XTLC.
See Figure 5.
C.Select the Activate button at the bottom of
the window.
Figure 5: Activate SIM/MEID
2. After the XTLC is installed at the site, use a keypad
and enter the panel’s Diagnostics menu (2313). Press COMMAND until you reach the Activate Cell menu.
A. Select ACTIVATE CELL by pressing a top row Select Key.
ACTIVATE CELL
SURE NO YES B. Press the button beneath YES on the next screen to activate the device.
Note: The ACTIVATE CELL option will only display if a CDMA modem is installed
and a Verizon Cellular Tower must be in contact with XTLC or activation
cannot be completed.
Panel Settings
Hitting a top row key allows access to the Serial Number, Panel Model, and Firmware Version.
Serial Number
This number is the panel serial number. Reference this number for date-of-manufacture,
hardware version, etc. Press the COMMAND key to view the next option.
Panel Model
This menu option displays the panel model.
Firmware Version
This menu option displays the Firmware Version number of the panel and date it was released.
Z-Wave Test Option
This feature allows the installer to test panel communication with Z-Wave devices. A
TEST
ZWAVE
DEVICE LIST:
HALLWAY LIGHT
HALLWAY LIGHT
LIGHT 02
0/0
HALLWAY LIGHT
99/99 SUCCESSFUL
successful test indicates a response from a device. Press any top row Select key to view
the Z-Wave Device List.
Press COMMAND to advance through each Z-Wave device and press any top row Select
key to begin the test on the device displayed.
The name of the device displays above the device number. The current number of
successful communications followed by the total number of attempts displays to the
right of the device number. The test stops after 99 attempts.
Press COMMAND to view the final number of successful communications.
Exiting the Diagnostics program
Press the COMMAND key until STOP displays. Press any Select key. The keypad returns to the Status List display.
Digital Monitoring Products
34
XTL/XTLC Programming Guide
APPENDIX
16.5
Using the 984 Command Function
16.6
Using the Walk Test
This feature allows the integrity of the cellular communication to be tested.
NBR: Not available for XTL/XTLC panels. If selected the keypad displays NO DIALER.
TEST: This option tests each function of the panel’s cellular communication. The tests proceed until a function
does not pass, or until all have been tested with positive results. The progress displays during each test.
PICKUP: Not available for XTL/XTLC panels. If selected the keypad displays NO DIALER.
The XTL/XTLC panel provides a walk test feature that allows a single technician to test all the protection
devices connected to zones on the system. Conduct the Walk Test within 30 minutes of resetting the panel. The
Walk Test automatically ends if no zones are tripped for 20 minutes. TEST IN PROGRESS displays at all keypads.
When five minutes remain, TEST END WARNING displays. If any areas are armed the Walk Test does not start
and SYSTEM ARMED displays.
WALK TEST
STD WLS PIR
Walk Test
To conduct the Walk Test, reset the control panel by pressing the reset button then wait
one minute. From the keypad, enter the code 8144. The keypad displays WALK TEST.
WLS (Wireless Check-in Test) - Select WLS to automatically test 1100 Series wireless
transmitter communications. Includes all wireless devices except key fobs and
transmitters programmed for a supervision time of 0 (zero).
PIR (Wireless PIR Walk Test) - The PIR Walk Test allows the installer to verify the 1126 and
1127 operation. When enabled, the 1126 LED flashes each time motion is detected for up to
30 minutes. This is a local test only and no messages are sent to the Central Station.
Trip Counter For DMP Wireless Check-in Test (WLS)
WALK TEST
TRIPS: XXX END Displays the number of wireless zones that automatically communicate a supervisory
check-in message.
•The number of zones that check in. (XX in the example).
•The total number of wireless zones programmed for supervision that should check in.
(ZZ in the example).
END - Select END to stop the Wireless Check-in Test. When the test ends or a 20-minute
time-out expires, normal wireless zone processing returns. If all transmitters check-in,
both numbers will match within three (3) minutes. If a transmitter has multiple zones
(1101, 1114, etc.), all zones will be included in the counts. Failed wireless zones then
display on the keypad.
TEST END WARNING
Test End Warning
Failed Zones Display
SOUTH LOBBY
ZONE: 10 -FAIL Each zone that did not trip at least once during the Walk Test displays on the keypad that
When no zones have been tripped and five minutes remain on the 20 minute Walk Test
timer, the keypad displays TEST END WARNING and the keypad tones. If no additional test
zone trips occur, the test ends and a final Sensor Reset automatically occurs. The System
Test End message is sent to the receiver along with Verify and Fail messages for each zone
under WALK test. Faulted zones then display on the keypad.
initiated the test. Any Fire (FI) Panic (PN) or Supervisory (SV) 24-hour zone that is faulted at
the end of the Walk Test displays a trouble condition for that zone regardless of the message
programmed for the open or short condition of the zone and a zone trouble is sent to the
receiver. Press the COMMAND key to display the next failed zone.
For the Wireless Check-in Test, failed wireless zones display only on the keypad. Zone
Verify/Fail reports are not sent to the central station receiver for the wireless checkin
test.
XTL/XTLC Programming Guide
Digital Monitoring Products
35
APPENDIX
16.7
16.8
Keypad Speaker Operation
When using LCD Keypads, the panel provides distinct speaker tones from the keypad for Fire, Burglary, Zone
Monitor, and Prewarn events. The list below details the conditions under which the speaker is turned on and off
for each event.
Fire
On - Fire zone alarm and Bell Output are ON.
Off - Alarm Silence or briefly when a key is pressed.
Burglary
On - Burglary zone alarm and Bell Output and is ON.
Off - Alarm Silence or briefly when a key is pressed.
Zone Monitor On - One time only when a monitored zone is tripped.
Off - After one tone.
Prewarn
On - During Entry Delay.
Off - When Entry Delay expires, when a Valid Code is entered, or when a key is pressed.
Cross Zoning
Caution must be taken when cross zoning devices to ensure that the Cross Zone Time is long enough to allow an
intruder to trip both devices before it expires. A Cross Zone Time that is too short may allow an intruder to trip
the devices and allow only a zone fault report be sent to the central station.
When a Cross Zoned zone trips, a FAULT report is sent to the SCS-1R Receiver. When two Cross Zoned zones trip
within the Cross Zone Time, both zones send ALARM signals to the receiver. For example, if zones 1 and 2 are
Cross Zoned zones, and only zone 1 trips, a FAULT report is sent to the receiver for zone 1. If zone 1 trips and
zone 2 trips within the Cross Zone Time, an ALARM report is sent to the receiver for zone 1 and zone 2.
Note: To operate correctly, all cross-zone zones need to be programmed as the same zone type.
16.9
Zone Type Descriptions
This section describes applications for the default zone types in Zone Information programming.
NT (Night Zone) - Controlled instant zone used for perimeter doors and windows and interior devices such as
PIRs and glassbreak detectors.
DY (Day zone) - Used for emergency doors or fire doors to sound the keypad buzzer and display the zone name
when the zone is faulted. Day zones also will send alarm reports to the receiver during the system’s armed
periods.
EX (Exit zone) - Initiates the entry delay timer when its assigned area is fully armed. Also, can initiate an exit
delay timer to allow a user to exit an area after the arming process has started.
PN (Panic zone) - Used for connecting to mechanical devices that allow a user to signal an emergency alarm.
Panic zones can provide either a silent or audible alarm with or without reporting to a central station receiver.
EM (Emergency zone) - These are used for reporting medical or other non-panic emergencies to the central
station.
SV (Supervisory zone) - Used to provide 24-hour zone supervision. Typical applications are high water, and low
and high temperature gauges.
FI (Fire zone) - Used for any type of powered or mechanical fire detection device. Typical applications are for
smoke detectors, sprinkler flow switches, manual pull stations, and beam detectors.
FV (Fire Verify zone) - Used primarily for smoke detector circuits to verify the existence of an actual fire
condition. When a Fire Verify zone initiates an alarm, the panel performs a Fire Reset. If any Fire zone initiates
an alarm within 120 seconds after the reset, an alarm is indicated. If an alarm is initiated after 120 seconds,
the cycle is repeated.
A1 and A2 (Auxiliary 1 and Auxiliary 2) - These zones are similar to a Night zone and are typically used to
protect restricted areas within a protected premises. Auxiliary 2 zones do not appear in the Status List.
AR (Arming zone) - Allows you to connect a keyswitch to a zone and use it to arm and disarm the system.
Digital Monitoring Products
36
XTL/XTLC Programming Guide
Assign Area and Disarmed condition for NT, DY,
EX, A1, and A2 only.
Assign Prewarn and Entry Delay for EX only.
Assign Style for AR only.
Assign 31 to 34 or 41 to 44 to Key Fobs.
Wireless output modules can be assigned to 31 to
34 and 41 to 44.
Supervision Time of 3 minutes can only be used
with Zone Types FI, FV and SV.
Zone Type Defaults
NIGHT
DAY
EXIT
FIRE
PANIC
EMERGENCY
SUPERVISORY
AUXILIARY 1
AUXILIARY 2
FIRE VERIFY
ARMING
XTL/XTLC Programming Guide
*
Y
N
N
N
N
N
N
N
N
N
N
N
or
N
1 0 N
2 3 or
3 60
4 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
1 240 Y
External
Contact N/O?
1114 Contact
Supervision
Time
LED Operation
Outputs = 31 to 34, or 41 to 44.
--
DY
FI
N EM
or A1
FV
Y
N
N
N
N
N
N
N
N
N
N
N
Contact
NT BDRM
EX
PN PERIM
SV
A2
INT
AR
or
or
1 to 6
EXT
NT
INT
DY
INT
EX
INT
FI
INT
PN
INT
EM
INT
SV
INT
A1
INT
A2
INT
FV
INT
AR
INT
INT
PIR Pulse Count
2
Sensitivity
S
S
S
S
S
0
0
0
0
0
S
P
M
F
Disarmed Armed Armed
Short
Open Short
A
A
–
T
–
A
T
L
–
0
0
0
0
0
A
T
L
–
S
P
M
F
S A 0 S
S A 0 S
S A 0 S
T 0 S
T 0 S
T 0 S
T 0 S
S T 0 S
S T 0 S
T 0 S
S
P
M
F
A
A
A
A
A
A
A
A
A
A
A
T
L
–
= This function not available for this zone type.
Low
Message
A
or or or T
L
Y 4 High –
Y 4 Low –
4 Low T
Y 4 Low –
4 Low
4 Low
4 Low
4 Low
4 Low T
4 Low T
4 Low
4 Low
Disarm-Disable
N
Disarmed
Open
Output *
DMP Wireless
Action
Area
Message
Type
Output *
Key
Fob
0
0
0
0
0
0
0
0
0
0
Prewarn
S N 1
P or to
M
F Y 5
S Y
S Y
S Y 1-5
S N
S N
S N
S N
S N
S N
S N
Action
Message
Output *
Action
Message
Output *
Action
Swinger
XTL/XTLC Zone Information
Style
Receiver Routing
Cross Zone
Priority
Traffic Count
Zone Audit Days
0
TGL
N N N 0 NORM TGL
ARM
1
or or or or to
DIS
2
STEP
BOTH
2 Y Y Y 99
MNT
N N N 0
N N
0
1 N N N 0
N
N N
0
N N
0
N N
0
N N
0 NORM
N N
0 NORM
Entry Delay
1
APPENDIX
Digital Monitoring Products
37
16.9
Zone Type Defaults
The XTL/XTLC panel contains 11 default zone types that provide the most commonly selected functions for
their applications. All zone types can be customized by changing the variable options listed below.
Key Fob - Indicates if a DMP key fob is programmed.
Type - These are the abbreviations displayed on the keypad for the zone types.
Area - For a ALL/PERIM or HOME/SLEEP/AWAY system, this is either Interior, Bedroom, or Perimeter. For an AREA
system use 1 to 6.
Wireless - 1100 Series Wireless options.
Contact - Indicates if the Universal Transmitter is programmed to use the internal or external contact.
External Contact N/O? - Identifies whether externally installed contacts are programmed as a normally open
(N/O) or normally closed (N/C) circuit. Y = N/O Contacts. N = N/C Contacts.
1114 Contact - Indicates if the 1114 Zone Expander is programmed for contact(s) 1, 2, 3, or 4.
Supervision Time - Selects the number of minutes for DMP wireless supervision.
1142 LED Operation - Identifies DMP 1142 Wireless Two-Button transmitter LED operation.
Disarm/Disable - Disables zone tripped messages from 1103 Transmitters and 1126/1127 PIRs while disarmed.
PIR Pulse Count - Selects the number of pulse counts the 1126/1127 uses before sending a short message.
Sensitivity - Sets sensitivity for the 1126/1127 PIR.
Message - A = alarm report, T = trouble report,
L = local with no report, — (dash) = no report.
Output - 31 to 34 and 41 to 44 wireless outputs or wireless key fob zones.
Action - This selects the type of relay output:
S = steady, P = pulse, M = momentary, and F = follow
Swinger Bypass - The zone can be automatically bypassed after a programmed number of trips.
Prewarn - This selects the keypad address that sounds the entry prewarn for this zone.
Entry Delay - Selects the entry delay timer used for this zone.
Priority - Requires this zone to be in a normal condition before the area can be armed.
Traffic Count - Provides the number of zone trips per area for Night and Exit type zones in a disarmed state.
Zone Audit Days - Number of days allowed to elapse without a zone being tripped before a message is sent.
Receiver Routing - This selects the routing option for Auxiliary 1 or Auxiliary 2 zone types.
Style - The abbreviations that display on the keypad for arming zone style. TGL = Toggle,
ARM = Arm only, DIS = Disarm only,
STEP = Wireless arming, MNT = Maintain
Digital Monitoring Products
38
XTL/XTLC Programming Guide
16.10 Common Keypad Messages
Message
Meaning
Possible Solutions
The user code you have entered is not
recognized by the system.
Check the user code and try again.
The schedule has expired but the system
has not been armed.
Users still on the premise should arm the system or
extend the schedule to a later time.
KEYPAD NAME - NOPWR
Wireless keypad is not getting proper
power.
Check that AC/DC transformer is plugged in
correctly.
AC TROUBLE
The system is not getting proper power.
Check that the AC connections are good.
BATTERY TROUBLE
The battery is either low or missing.
Check that the battery connections are good and
the battery is still good.
SYSTEM TROUBLE or
SERVICE REQUIRED
There is a problem with one or more
components in the system.
Press the reset button for 1-2 seconds.
SYSTEM BUSY
The system is performing another task
with a higher priority.
Wait a few moments for the system to complete the
task. If the message displays for a long period of
time, the processor could be locked up.
TRANSMIT FAIL
The panel has attempted to communicate
with the central station 10 times and has
not succeeded.
Verify your communication type, account number,
and IP address.
ENTER CODE (When
entering Programming)
A lockout code has been programmed for
the panel.
Enter the lockout code.
INVALID CODE
CLOSING TIME
16.11 Z-Wave Certification Information
The 738Z is a security enabled Z-Wave product and is designed to be used as a primary controller.
The XFER feature allows an existing 3rd party network to be transferred into the 738Z. To add the 738Z to another 3rd
party network, please contact technical support. This function is available with Remote Link.
The 738Z can support Z-Wave products from different vendors and product categories. It is recommended to use devices
listed on the buy.dmp.com site for best performance.
Z-Wave terminology:
•
Inclusion is the process of adding a device to the Z-Wave network. The new device is ‘included’ into the
Z-Wave network. See “Adding 6-Wave Devices” in section 7 of Z-Wave Setup in this programming guide.
•
Exclusion is the process of removing a device from the Z-Wave network. The new device is ‘excluded’ from
the Z-Wave network. See “Remove” in section 6 of Z-Wave Setup in this programming guide.
•
Replication is the process of copying network information to another device (typically a Z-Wave controller)
in the Z-Wave network. See “Transfer Control” in Z-Wave Setup in this programming guide.
XTL/XTLC Programming Guide
Digital Monitoring Products
39
REVISIONS
Revisions to This Document
This section explains the changes made to this document during this revision. It lists the date and identifies the
change(s) made, the related section number and section heading, and a summary of the change.
Ver. Section Number and Heading
1.07
Entire Document
Entire Document
9.19 Weather Zip Code
17.4 Diagnostics Function
18.3 Diagnostics Function
Quick Explanation of Changes
Added references to XTLC
Removed Z-Wave Setup
Added section
Added Cell Roaming Indicator on XTLC section
Added Z-Wave Diagnostics function
1.06
11.13 Heat Saver Temperature
11.14 Cool Saver Temperature
Added section
Added section
1.05
6.1-6.8 Z-Wave Setup
11.1 Output Options
11.6 Panic Alarm Output
11.8 Begin Exit Output
11.9 End Exit Output
11.11 Armed Output
11.12 Disarmed Output
11.13 Burglary Output
17.11 Z-Wave Certification Information
Added
Added
Added
Added
Added
Added
Added
Added
Added
1.04
8.18 False Alarm Question
16.4 Diagnostics
Added option
Added Cellular Signal option and reference to dB indication
section
Z-Wave Favorites references
section
section
section
Z-Wave Favorites references
section
section
section
1.03
4.1 Messaging Setup
4.5 Destination 1 User Number
4.12 Monthly Limit
8.9 Swinger Bypass Trips
13.14 Swinger Bypass
16.9 Zone Type Defaults
Added MyAccess™ information
Added Late to Open and Early to Close to list of messages
Added MyAccess™ information
Added MyAccess™ information
Added section
Changed Swinger Bypass trip information
Changed Swinger Bypass trip information
1.02
Added Wireless option
Added Closing Wait operation explanation
Changed output to three minutes
Added Normally Open section
Added missing options
Added Cross Zoning information section
Added Disarm-Disable, PIR Pulse Count, and Sensitivity
5.4 Wireless
9.3 Automatic Bell Test
10.7 Arm-Alarm Output
13.10 Contact
16.6 Using the Walk Test
16.8 Cross Zoning
16.9 Zone Type Defaults
Digital Monitoring Products
40
XTL/XTLC Programming Guide
XTL/XTLC Programming Guide
Digital Monitoring Products
41
Certifications
California State Fire Marshall (CSFM)
ANSI/SIA CP-01 False Alarm Reduction
ANSI/UL 1023Household Burglar
ANSI/UL 985 Household Fire Warning
ANSI/UL 1610Central Station Burglar (Cellular)
FCC Wireless Approvals
FCC Part 15 ID: CCKPC0117
Industry Canada ID: 5251A-PC0117
ANSI/SIA CP-01 False Alarm Reduction
ANSI/UL 1023 Household Burglar
ANSI/UL 985 Household Fire Warning
ANSI/UL 1610 Central Station Burglar (Cellular)
800-641-4282
INTRUSION • FIRE • ACCESS • NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Designed, Engineered and
Assembled in USA
Springfield, Missouri 65803-8877
15105
FCC Cellular Approvals for XTLC
Cellular FCC Part 15: MIVCNN0301
Cellular Industry Canada: 4160A-CNN0301
LT-1108 1.07 © 2015 Digital Monitoring Products, Inc.
FCC Cellular Approvals for XTL
Cellular FCC: MIVGSM0308
Cellular Industry Canada: 4160A-GSM0308