V2930
OWNER’S GUIDE
www.sharkclean.com
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
READ ALL INSTRUCTIONS BEFORE USING YOUR
SHARK® CORDLESS FLOOR AND CARPET SWEEPER.
WHEN USING YOUR SHARK CORDLESS FLOOR AND
CARPET SWEEPER, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE OBSERVED, INCLUDING THE
FOLLOWING:
14DO NOT put any object into openings. Do not use
with brush roll blocked; keep free of fiber, lint, hair
and anything that may prevent the brush roll from
working.
15Keep hair, loose clothing, fingers and all parts of
body away from openings and moving parts.
WARNING: TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR INJURY:
16DO NOT pick up anything that is burning or
smoking, such as cigarettes, matches or hot
ashes.
1 Read and follow all label, operational and marking
instructions.
17DO NOT use to pick up flammable or combustible
liquids such as gasoline or use in areas where they
may be present.
2Use ONLY as described in this manual. Use only
manufacturer’s recommended attachments.
18DO NOT attempt to change accessories while the
unit is running.
3
DO NOT allow to be used as a toy. Close attention
is necessary when used by or near children.
19DO NOT use the cordless floor and carpet sweeper
without the dust container in place.
4
DO NOT use for any purpose other than described
in this user’s guide.
20Use extra care when cleaning on stairs.
5DO NOT use with damaged cord or plug. Do not
use the cordless floor and carpet sweeper if it has
been dropped, damaged, left outdoors, or dropped
in water. Return it to EURO-PRO Operating LLC for
examination, repair or adjustment.
6
DO NOT abuse the charger cord. Never carry the
charger or base by the cord or yank to disconnect
from an outlet; instead grasp the charger and pull
to disconnect.
7Keep the charger cord away from heated surfaces.
8
DO NOT use the charger with an extension cord.
Plug the charger directly into an electrical outlet.
Use charger only in a standard (120V., 60Hz.)
electrical outlet.
9
DO NOT attempt to use the charger with any other
product or attempt to charge this product with
another charger. Use only the charger model
YLS0041-T080020 supplied with this cordless
floor and carpet sweeper.
10DO NOT charge this unit outdoors.
11DO NOT use outdoors or on wet surfaces.
12DO NOT handle plug or appliance with wet hands.
13 Use only on dry, indoor surfaces.
2
TOLL FREE: 1-800-798-7398
21Store the cordless floor and carpet sweeper
indoors. Store after use to prevent accidents.
22Leaks from battery cells can occur under extreme
conditions. If the liquid, which is 20-35% solution
of potassium hydroxide, gets on the skin - wash
immediately with soap and water or neutralize with
a mild acid such as lemon juice or vinegar. If the
liquid gets into the eyes, flush them immediately
with clean water for a minimum of 10 minutes and
seek medical attention.
23This product includes rechargeable nickel metal
hydride batteries. Batteries must be recycled
or disposed of properly. Do not incinerate the
batteries or expose to high temperatures as they
may explode.
24 The cordless floor and carpet sweeper must
be disconnected from the power supply when
removing the battery.
25 To reduce the risk of electrical shock, do not put
the charger and sweeper body in water or other
liquid. Do not place or store the appliance where it
can fall or be pulled into a tub or sink.
TO MAXIMIZE THE LIFE OF YOUR
NI-MH BATTERIES:
1Charge for 7 hours before initial use. Failure
to do so will reduce the product’s battery life
significantly.
2For best battery performance, remove the
charging adapter from the unit after the charging
period has completed.
3
Do not store the unit with the charging adapter
attached and plugged in.
4For maximum battery life, only recharge the unit
when the batteries are close to fully discharged. It
is best to fully discharge the batteries at least once
a month.
5DO NOT store in areas of high temperature or
humidity.
6After 3 months of non-use, the product should be
fully discharged and then recharged to maximize
battery power.
7Ni-MH batteries have a long useful life but at some
time they will need to be replaced. To purchase
replacement batteries, visit www.sharkclean.com.
NOTE: The power button must be in the “Off”
position in order to charge the unit. If the charging
indicator does not light, press the power button
once.
Warning: Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
SAVE THESE INSTRUCTIONS
www.sharkclean.com
3
QUICK START
IMPORTANT: Before you can start using your new
cordless floor and carpet sweeper, charge it for 7
hours.
NOTE: The charging adapter and lower handle will be
shipped inside the packaging.
Fig. 1
Fig. 2
ASSEMBLE
CLEAN
1Insert the smaller end of the
lower handle into the top of the
unit. Push until firmly in place.
Assemble the upper and lower
poles into the elbow joint to
form the Shark® Backsaver™
folding handle. Then insert it
into the top of the lower handle.
(Fig. 1)
2Pull back on the handle and
press lightly on the body of the
unit with your foot to engage the
steering. (Fig. 2)
4
TOLL FREE: 1-800-798-7398
Fig. 3
3Using your foot, press the
power button and push the unit
forward over the surface you
wish to clean. (Fig. 3)
Fig. 4
Fig. 6
Fig. 5
EMPTY
4The Shark® Backsaver™ folding
handle makes cleaning under
furniture a breeze. Just press
the button on the handle with
your thumb to engage the
Shark® Backsaver™ function.
(Fig. 4)
5When you’re finished cleaning,
pull the dust container straight
out from the side. (Fig. 5)
NOTE: Be careful not to
accidentally turn the unit on.
6Empty dust container contents.
(Fig. 6) If desired, you may
rinse with water to clean
the dust container - but dry
thoroughly before replacing.
When finished, replace the dust
container.
www.sharkclean.com
5
ASSEMBLY
B
A
C
Fig. 1
D
H
G
E
F
a
I
b
Fig. 3
Fig. 2
COMPONENTS:
ASSEMBLY OF YOUR FLOOR
AND CARPET SWEEPER:
A Main Unit
NOTE: The charging adapter
and lower handle will be
shipped inside the packaging.
B Power Button
C Dust Container
D Lower Handle
EBacksaver™ Release Button
F Upper Pole with Handle
GShark® Backsaver™ Joint
H Lower Pole
I
Charging Adapter
Model Number: V2930 32
Voltage: 4.8 V
6
1Insert the smaller end of the
lower handle into the top of the
unit. Push until firmly in place.
(Fig. 1)
2Slide the upper pole (the tube
with the handle) into the end
of the Shark® Backsaver™ joint
that has a small notch in it (a).
Then slide the lower pole into
the other end of the joint (b).
Push it in until it clicks into
place. (Fig. 2)
TOLL FREE: 1-800-798-7398
3Insert the Shark® Backsaver™
folding handle you just
assembled into the top of the
lower handle. You should hear
the locking tab click into place.
(Fig. 3)
IMPORTANT: Charge the
batteries for 7 hours before
using the unit for the first time.
See page 7 for instructions on
charging your unit.
CHARGING YOUR CORDLESS FLOOR AND CARPET SWEEPER
OFF
Fig. 5
Fig. 4
1Always make sure that the unit
is turned off. (Fig. 4)
2Insert the charger plug into the
hole on the back of the unit.
Plug the charger into a wall
outlet. The light next to the
power button will illuminate
when the unit is charging. If the
unit is plugged in and the light is
not illuminated, press the power
button once. The light should
now be illuminated indicating
that the unit is charging.
(Fig. 5) Once the charge is
completed, the light will go off.
3Charge the battery for 7 hours
before initial use and 7 hours
for each recharge. Your cordless
floor and carpet sweeper is
powered by NIi-MH batteries
that need this time to build up
their charge.
IMPORTANT: Although many
adaptors look similar, it’s
important to use only the
adaptor that came with the unit
(XA2700).
4For best battery performance,
remove the charging adapter
from the unit after the charging
period has completed. Storing
the unit with the adapter
attached and plugged in will
reduce the battery life.
USING YOUR CORDLESS FLOOR AND CARPET SWEEPER
Fig. 6
1Press the power button to
start the unit. When finished
cleaning, press the power
button again to turn the unit off.
(Fig. 6)
2To clean under furniture, use
the Shark® Backsaver™ folding
handle. Press the handle
Fig. 7
release button and apply a bit
of pressure to bend the handle
forward. (Fig. 7) The Shark®
Backsaver™ joint will release
from the locked position to
reach messes under furniture.
(Fig. 8)
Fig. 8
3Do not use the unit to pick up
liquids or clean wet floors.
4Do not use the unit on concrete,
tar or other rough surfaces.
5Do not use the unit to pick
up pieces of string or fabrics.
Do not use the unit to clean
tasseled or frayed carpets.
www.sharkclean.com
7
EMPTYING THE DUST CONTAINER
Fig. 10
Fig. 9
1To achieve the best
performance, empty the dust
container after each use. Pull
the dust container straight out
from the side. (Fig. 9)
2Empty dust container contents.
(Fig. 10) If desired, you may
rinse with water to clean
the dust container - but dry
thoroughly before replacing.
NOTE: Be careful not to
accidentally turn the unit on.
8
TOLL FREE: 1-800-798-7398
Fig. 11
3Re-insert the dust container into
the unit. (Fig. 11)
MAINTENANCE
Fig. 12
Fig. 14
Fig. 13
Fig. 15
CAUTION: Do not clean the unit
while it is charging.
1Once a month, wipe down the
unit with a dry cloth, including
the area under the dust
container. Wipe away any hair,
fiber or other dirt that may have
built up in the chamber and on
the rotating brush. Do not use
any harsh cleaner or chemicals.
2Do not immerse the unit in
water.
CLEANING THE ROTATING BRUSH
1Pull the dust container straight
out from the side of the unit to
remove. (Fig. 9)
2Turn the unit upside down. Be
careful not to accidently turn
the unit on!
3Remove all hair, string or fibers
wrapped around the brush
bar. Using a pair of scissors,
carefully cut along the raised
guide to remove anything
wound around the brush bar.
Avoid damaging or cutting the
bristles. (Fig. 12)
REMOVING AND REPLACING THE
BATTERY
5Connect the wire terminal from
the unit to the wire terminal
connector of the new battery
pack and replace the battery
pack into the unit. Replace the
battery compartment cover.
NOTE: If uncertain as to how
to remove your battery pack,
we suggest you take the unit
to a reputable small appliance
service technician to have this
service performed.
6Follow the instructions on page
7 to charge your new battery
pack. Please call customer
service at 1-800-798-7398
if you have any problems
removing the battery pack.
4Use a coin to remove the trap
door if you need to remove the
brushroll to either clean it or
replace it. (Fig. 13)
1Pull the dust container straight
out from the side of the unit to
remove. (Fig. 9)
2Turn the unit upside down. Be
careful not to accidently turn
the unit on!
3Push in the locking tab and lift
off the battery compartment
cover. (Fig. 14)
4Carefully lift out the battery
pack and disconnect the wire
terminals by pressing on the
latch and pulling apart the wire
terminal connectors. Remove
the battery pack. (Fig. 15)
IMPORTANT This appliance
contains Ni-MH batteries. The
batteries must be recycled
or disposed of in accordance
with local regulations. Please
consult your Yellow Pages or
local recycling center for more
information.
WARNING: Never use ordinary
batteries for replacement as
these may leak and cause
damage. Use only battery pack
XB2700 for replacement.
Ni-MH BATTERY
MUST BE RECYCLED
OR DISPOSED OF
PROPERLY
www.sharkclean.com
9
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASONS AND SUGGESTED SOLUTION
The unit will not operate
Batteries need to be recharged.
Batteries are dead and need to be replaced.
There is no power in the electrical outlet supplying the charging adapter. Try to
charge using a different outlet.
Ensure the wire terminal connectors on the battery pack are securely attached.
Clear any obstruction from the rotating brush. Turn unit off for 10 seconds, and
then restart.
If the unit still doesn’t work, call Customer Service at 1-800-798-7398.
The unit will not pick up
Empty the dust container.
Recharge the battery.
Dust is escaping from the unit
Empty the dust container.
Ensure that the dust container is properly in place.
The rotating brush will not
pick up
Check for and remove any excessive material on the brush roll or in the
bottom of the unit.
Empty the dust container.
The unit will not charge
Press the power button once to turn the unit “OFF”.
There is no power in the electrical outlet supplying the charging adapter.
Try to charge using a different outlet.
Ensure the wire terminal connectors on the battery pack are securely attached.
Charging adapter may not be working. Call Customer Service at
1-800-798-7398.
Batteries are dead and need to be replaced.
ORDERING REPLACEMENT PARTS
REPLACEMENT PARTS
A XB2700
Battery Pack
B XA2700
AC Adapter
C 1125FK-2930 Brush Bar Replacement Kit
To order any of the above replacement parts, go to www.sharkclean.com or call 1-800-798-7398.
10
TOLL FREE: 1-800-798-7398
WARRANTY & PRODUCT REGISTRATION
EURO-PRO ONE-YEAR (1) LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a
period of one (1) year from the date of purchase when utilized for normal household use, subject to the following
conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at
our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has
been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused
by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited
Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs,
service or alteration to the product or any of its parts, which have been performed by a repair person not
authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid.
For customer service support, call 1-800-798-7398 or visit our website at www.sharkclean.com.
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLC’s sole
discretion, we will repair or replace it free of charge. Proof of purchase date and a check made payable to EUROPRO Operating LLC in the amount of $19.95 to cover the cost of return shipping and handling must be included.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require
replacement are specifically excluded from warranty.
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific
obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO
Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states
do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to
you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state or province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach a tag to item before packing including your name, complete address and phone number
with a note giving purchase information, model number and what you believe is the problem with the
item. We recommend you insure the package (as damage in shipping is not covered by your warranty).
Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to
improve our products, therefore the specifications contained herein are subject to change without notice.
PRODUCT REGISTRATION
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10)
days of purchase. You will be asked to provide the store name, date of purchase and model number along with your
name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering
you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
www.sharkclean.com
11
Copyright © 2013 Euro-Pro Operating LLC
USA: Newton, MA 02459
CANADA: Ville St-Laurent, QC H4S 1A7
Printed in China
Illustrations may differ from actual product.
Euro-Pro and Shark, are trademarks
of Euro-Pro Operating LLC.
V2930.E.130826.5
www.sharkclean.com
1-800-798-7398