Sharp 14MR10 Service manual

14LK22
SERVICE MANUAL
S71X114LK22//
COLOR TELEVISION
Chassis No. MSA
MODEL
14LK22
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 4
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 5
» CHASSIS LAYOUT ............................................................................................................................. 13
» BLOCK DIAGRAM .............................................................................................................................. 14
» DESCRIPTION OF SCHEMATIC DIAGRAMS .................................................................................... 15
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 19
» REPLACEMENT PARTS LIST ............................................................................................................ 22
» PACKING OF THE SET ...................................................................................................................... 27
ELECTRICAL SPECIFICATIONS
POWER INPUT ........................................ 110-220 V AC 50/60 Hz
POWER RATING .................................................................... 53 W
2
PICTURE SIZE ........................................... 574cm (88.97sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE ............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
UHF-Channels ............................................................ 14 thru 69
Sound IF Carrier Frequency ...................................... 41.25 MHz
CATV Channels ........................................................... 1 thru 125
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ................................ 0.9W (at 10% distortion)
Specifications are subject to change without
prior notice.
SHARP CORPORATION
1
14LK22
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
14LK22
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon and etc.) and measure the AC voltage
drop across the resistor.
AII checks must be repeated with the AC ine cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators and etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
14LK22
LOCATION OF USER'S CONTROL
Front Panel
VIDEO/AUDIO IN TERMINALS
(VIDEO/AUDIO terminals are also
provided on the rear.)
CHANNEL UP/DOWN
POWER
Press
®
®
On.
Press again
Off.
(
) Selects next higher channel.
(
) Selects next lower channel.
ON TIMER indicator
VOLUME UP/DOWN
(+) Increases sound.
SENSOR AREA FOR
REMOTE CONTROL
(Ð) Decreases sound.
MENU
Press
®
®
Accesses MAIN MENU.
Press again
Exits MAIN MENU.
Basic Remote Control Functions
Infrared Transmitter Window
®
POWER
Press
®
INPUT
®
On.
Press again
Press
Off.
Switch to external video input
mode.
Press again
REMOTE KEYPAD
®
Switch to TV mode.
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
CHANNEL UP/DOWN
VOLUME UP/DOWN
(
) Selects next higher channel.
(+) Increases sound.
(
) Selects next lower channel.
(Ð) Decreases sound.
¥ Moves the Ò
¥ In menu mode, changes or selects
Ó mark of the MENU
screen.
the TV adjustments.
®
MUTE
Press
¥
®
Mutes sound.
Press again
®
MENU
Restores sound.
Press
CLOSED CAPTION appears when
sound is muted.
®
®
Accesses MAIN MENU.
Press again
Exits MAIN MENU.
DISPLAY
Press
Displays receiving channel for
4 seconds.
Press again
®
Removes display.
¥ Te m p o r a r i l y d i s p l a y s r e c e i v i n g
channel when in Closed Caption
mode.
TV
4
14LK22
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 3.15A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
+B DC REGULATOR CONFIRMATION
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 110~220V
AC line voltage, with a strong air signal or a properly
tuned in test signal.
3. Receive a good local channel.
4. The voltage should be approximately, 23.5kV (at
picture MAX, Bright center condition).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
The + B DC output voltage adjustment is not included
in this circuit.However, should confirmation be
reguired proceed as follows.
1. Actuate receiver with 220V AC input voltage.
2. Receive a local channel.
3. Connect positive lead of digital voltmeter to C754
positive side on PWB-A ; negative lead to chassis
ground.
4. Confirm this voltage reading is as below.
CAUTION: The reading should be within 130 ± 2.0V DC
to ensure normal function and circuitry
reliability.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 220V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.1 ± 1.5 V.
5. Apply external 27.9V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
5
14LK22
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
To enter the service mode and exit service mode.
Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.
Short JA137&JA138 for 1 Second and release to switch
to the service mode position, and the microprocessor is
in input mode.(Adjustment through the I2C bus control.)
To exit the service mode, turn the television off by
pressing the power button.
2. Service item selection
Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set.
The service adjustment item will vary in increments
of one. Select the item you wish to adjust.
3. Data number selection
Press the Vol-up or down button to adjust the data
number.
DATA NUMBER
SERVICE ADJUSTMENT ITEM
AGC:
Figure A.
6
25
14LK22
SERVICE MODE
(1) In the Service Mode, Key is used to select the mode in the following oreder.
AGC &
GEOMETRIC
MODE
WHITE POINT
ADJ.
MODE
SUB
ADJ.
MODE
OFFSET
ADJ.
MODE
FEATURE
OPTION
MODE
IC
OPTION
MODE
AGC &
GEOMETRIC
MODE
WHITE POINT
ADJ.
MODE
↓
AGC TAKE OVER POINT (AGC)
↓
VERTICAL SLOPE (V-LIN)
↓
VERTICAL AMP (V-AMP)
↓
VERTICAL SHIFT (V-CENT)
↓
VERTICAL ZOOM (V-ZOOM)
↓
HORIZONTAL SHIFT (H-CENT)
↓
EAST-WEST WIDTH (H-SIZE)
↓
HORIZONTAL PARALLELOGRAM (EW//)
↓
EAST-WEST PARABOLA / WIDTH (PARA)
↓
EAST-WEST UPPER CORNER
PARABOLA (COR(U))
↓
EAST-WEST LOWER CORNER
PARABOLA (COR(L))
↓
EAST-WEST TRAPEZIUM (TRAPE)
↓
HORIZONTAL BOW (HB)
↓
S-CORRECTION (S-COR)
↓
W.P. RED OFFSET HIGH /
OFFSET BLUE TONE (DRI-R-HI)
↓
W.P. GREEN OFFSET HIGH /
OFFSET BLUE TONE (DRI-G-HI)
↓
W.P.BLUE OFFSET HIGH /
OFFSET BLUE TONE (DRI-B-HI)
↓
W.P. RED MH / STD (DRI-R-MH)
↓
W.P. GREEN MH / STD (DRI-G-MH)
↓
W.P. BLUE MH / STD (DRI-B-MH)
↓
W.P. RED OFFSET ML /
OFFSET RED TONE (DRI-R-ML)
↓
W.P. GREEN OFFSET ML /
OFFSET RED TONE (DRI-G-ML)
↓
W.P. BLUE OFFSET ML /
OFFSET RED TONE (DRI-B-ML)
↓
W.P. RED OFFSET LOW (DRI-R-LO)
↓
W.P. GREEN OFFSET LOW (DRI-G-LO)
↓
W.P. BLUE OFFSET LOW (DRI-B-LO)
7
MTS
ADJ.
MODE
SUB
ADJ.
MODE
↓
MAX VOLUME (SUB-VOL)
↓
SUB CONTRAST (SUB-CON)
↓
SUB TINT (SUB-TINT)
↓
SUB COLOUR (SUB-COL)
↓
SUB BRIGHTNESS (SUB-BRI)
↓
SUB SHARPNESS (SUB-SHP)
↓
MAX HOTEL VOLUME (HTL-VOL)
↓
HOTEL PROGRAM NO(HTL-PRG)
↓
BLUE BACK CONTRAST (BB-CON)
↓
OSD GRB REFERENCE (RGB)
↓
BLACK LEVEL OFFSET R(CUT-R)
↓
BLACK LEVEL OFFSET G(CUT-G)
↓
CATHODE DRIVE LEVEL(CDL)
14LK22
MTS
OFFSET
ADJ.
MODE
ADJ.
MODE
↓
Y-D TIME (TV) [ YD ] (DL-TV)
↓
Y-D TIME (AV) [ YD ] (DL-AV)
↓
INITIAL/DEFAULT LANGUAGE (INIT)
↓
FAO-MAX VOLUME (FAO-VOL)
↓
ENERGY SAVE OFFSET (ESV_OFFS)
↓
CLOSE CAPTION POSITION (CCPOS)
↓
ATTENUATE INPUT SIGNAL LEVEL (ATT)
↓
VCO FREE RUNNING FREQUENCY ADJ. (VCO)
↓
STEREO, SAP, DBX FILTER ADJ. (FILTER)
↓
STEREO SEPARATION ADJUSTMENT (300HZ) (WIDEBAND)
↓
STEREO SEPARATION ADJUSTMENT (3kHZ) (SPECTRAL)
↓
BASS LEVEL (BASS)
↓
TREBLE LEVEL (TREBLE)
IC
OPTION
MODE
FEATURE
↓
VERTICAL SCAN DISABLE (VSD)
↓
BLACK STRETCH (BKS)
↓
AUTOMATIC VOLUME LEVELLING (AVL)
↓
FAST FILTER IF-PLL ( FFI )
↓
ENABLE VERTICAL GUARD ( EVG )
↓
EHT TRACKING MODE ( EHT )
↓
OVERSCAN SWITCH OFF (OSO)
↓
AUTO COLOUR LIMIT (ACL)
↓
FORCED COLOUR-ON (FCO)
↓
VIDEO MUTE AT IDENT LOSS (VMI)
↓
VIDEO MUTE AT PROGRAM/SOURCE CHANGE (VMC)
↓
HOTEL MODE (HTL)
↓
GAIN FM DEMODULATOR (BTSC)
↓
CHARGE PUMP (CP)
↓
FM WINDOW SELECTION (FMWS)
↓
SOUND MUTE BIT 0 (SM0)
↓
SOUND MUTE BIT 1 (SM1)
↓
IF AGC SPEED BIT 0 (AGC0)
↓
IF AGC SPEED BIT 1 (AGC1)
↓
PHI 1 TIME CONSTANT FOR FE (FOA-FE)
↓
PHI 1 TIME CONSTANT FOR FE (FOB-FE)
↓
PHI 1 TIME CONSTANT FOR AV (FOA-AV)
↓
PHI 1 TIME CONSTANT FOR AV (FOB-AV)
↓
FORCED SLICING LEVEL FOR VERTICAL SYNC.(FSL)
↓
SYNCHRONISATION OF OSD/TEXT DISPLAY (HP2)
↓
RGB BLANK (RGBL)
↓
V-CHIP (V-CHIP)
↓
MTS DECODING ENABLED (MTS)
↓
DEMO MODE (DEMO)
↓
REAL TIME CLOCK / ON TIMER (CLOCK)
↓
ENERGY SAVE (E-SAVE)
↓
PERSONAL PREFERENCE PROGRAM (P_PREF)
↓
UNIVERSAL PLUS (UNIV+)
↓
SPEAKER ON/OFF (SPEAKER)
↓
FIXED AUDIO OUT (FAO)
↓
VIEW TIMER (VIEW-TM)
↓
FRENCH LANGUAGE (FRENCH)
↓
EZ SETUP / AUTOPRESET (EZ-SETUP)
↓
WHITE TEMP OR FAVORITE COLOR (W-TEMP)
↓
AV ENABLED OR DISABLED (AV)
↓
AV2 ENABLED OR DISABLED (AV2)
↓
DYNAMIC SKIN CONTROL (DSK)
↓
RATIO PRE- AND OVERSHOOT BIT 0 (RPO0)
↓
RATIO PRE- AND OVERSHOOT BIT 1 (RPO1)
↓
GAIN FM DEMODULATOR (AGN)
↓
AUTO SWITCH OFF ENABLED (AUTO-OFF)
OPTION
MODE
FORWARD : CH DOWN KEY
REVERSE : CH UP KEY
(
) means OSD display.
Figure B: ADJUSTMENT CATEGORIES
1Press the CH DOWN/UP key on the remote controller to get ready to select the mode one by one.
2Press the CH DOWN/UP key on the remote controller to select the modes reversibly one by one.
3Using the VOLUME UP/DOWN key on the remote controller, the data can be modified.
(OSD disturbance can be erased by R/C display key)
8
14LK22
SERVICE MODE
SERVICE
POSITION
ADJUST ITEM
AGC
V-LIN
V-AMP
V-CENT
V-ZOOM
H-CENT
H-SIZE
EW//
PARA
COR(U)
COR(L)
TRAPE
HB
S-COR
DRI-R-HI
DRI-G-HI
DRI-B-HI
DRI-R-MH
DRI-G-MH
DRI-B-MH
DRI-R-ML
DRI-G-ML
DRI-B-ML
DRI-R-LO
DRI-G-LO
DRI-B-LO
SUB-VOL
SUB-CON
SUB-COL
SUB-BRI
SUB-TINT
SUB-SHP
HTL-VOL
HTL-PRG
BB-CON
RGB
CUT-R
CUT-G
CDL
DL-TV
DL-AV
INIT
AGC TAKE OVER POINT
VERTICAL SLOPE
VERTICAL AMP
VERTICAL SHIFT
VERTICAL ZOOM
HORIZONTAL SHIFT
EAST-WEST WIDTH
HORIZONTAL PARALLELOGRAM
EAST-WEST PARABOLA / WIDTH
EAST-WEST UPPER CORNER PARABOLA
EAST-WEST LOWER CORNER PARABOLA
EAST-WEST TRAPEZIUM
HORIZONTAL BOW
S-CORRECTION
“W,P RED OFFSET HIGH / OFFSET BLUE TONE”
W.P. GREEN OFFSET HIGH / OFFSET BLUE TONE
W.P.BLUE OFFSET HIGH / OFFSET BLUE TONE
W.P. RED MH / STD
W.P. GREEN MH / STD
W.P. BLUE MH / STD
W.P. RED OFFSET ML / OFFSET RED TONE
W.P. GREEN OFFSET ML / OFFSET RED TONE
W.P. BLUE OFFSET ML / OFFSET RED TONE
W.P. RED OFFSET LOW
W.P. GREEN OFFSET LOW
W.P. BLUE OFFSET LOW
MAX VOLUME
SUB CONTRAST
SUB COLOUR
SUB BRIGHTNESS
SUB TINT
SUB SHARPNESS
MAX HOTEL VOLUME
HOTEL PROGRAM NO
BLUE BACK CONTRAST
OSD GRB REFERENCE
BLACK LEVEL OFFSET R
BLACK LEVEL OFFSET G
CATHODE DRIVE LEVEL
Y-D TIME (TV) [ YD ]
Y-D TIME (AV) [ YD ]
INITIAL/DEFAULT LANGUAGE
FAO-VOL
ESV_OFFS
CCPOS
ATT
VCO
FILTER
WIDEBAND
SPECTRAL
BASS
TREBLE
VSD
BKS
AVL
FFI
EVG
EHT
OSO
ACL
FCO
VMI
VMC
HTL
BTSC
CP
FAO-MAX VOLUME
ENERGY SAVE OFFSET
CLOSE CAPTION POSITION
ATTENUATE INPUT SIGNAL LEVEL
VCO FREE RUNNING FREQUENCY ADJ.
“STEREO, SAP, DBX FILTER ADJ. “
STEREO SEPARATION ADJUSTMENT (300HZ)
STEREO SEPARATION ADJUSTMENT (3kHZ)
BASS LEVEL
TREBLE LEVEL
VERTICAL SCAN DISABLE
BLACK STRETCH
AUTOMATIC VOLUME LEVELLING
FAST FILTER IF-PLL
ENABLE VERTICAL GUARD
EHT TRACKING MODE
OVERSCAN SWITCH OFF
AUTO COLOUR LIMIT
FORCED COLOUR-ON
VIDEO MUTE AT IDENT LOSS
VIDEO MUTE AT PROGRAM/SOURCE CHANGE
HOTEL MODE
GAIN FM DEMODULATOR
CHARGE PUMP
DATA
RANGE
INITIAL VALUE FIX/ADJ
0~63
14
ADJ
0~63
32
ADJ
0~63
32
ADJ
0~63
32
ADJ
0~63
32
FIX
0~63
32
ADJ
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
0
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
25
FIX
0~63
32
ADJ
0~63
32
ADJ
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
32
FIX
0~63
63
FIX
0~63
63
FIX
0~63
32
ADJ
0~63
32
ADJ
0~63
32
ADJ
0~63
32
FIX
0~63
32
FIX
0~125 or >125 for none
255
FIX
0~15
10
FIX
0~15
15
FIX
0~63
32
ADJ
0~63
32
ADJ
0~15
0
FIX
0~15
12
FIX
0~15
12
FIX
0(English), 1(Spanish),
0
FIX*
2(French)
0~63
63
FIX
0~63
10
FIX
0~255
32
ADJ
0~15
10
FIX
0~63
32
FIX
0~63
28
FIX
0~63
32
FIX
0~63
27
FIX
0~15
8
FIX
0~15
8
FIX
0 or 1 when item selected
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(fast tuning) or 1
0
FIX
(moderate speed tuning)
9
REMARK
must be "17"
must be "32"
must be "33"
must be "37"
must be "32"
must be "32"
must be "32"
must be "25"
must be "32"
must be "22"
must be "19"
must be "63"
must be "52"
must be "24"
must be "5"
must be "15"
must be "2"
must be "2"
must be "8"
14LK22→1/14MR10→0
must be "63"
must be "20"
14LK22
DATA
SERVICE
POSITION
ADJUST ITEM
FMWS
SM0
SM1
AGC0
AGC1
FOA-FE
FOB-FE
FOA-AV
FOB-AV
FSL
HP2
RGBL
V-CHIP
MTS
DEMO
CLOCK
E-SAVE
P_PREF
UNIV+
SPEAKER
FAO
VIEW-TM
FRENCH
EZ-SETUP
FM WINDOW SELECTION
SOUND MUTE BIT 0 (SM0)
SOUND MUTE BIT 1
IF AGC SPEED BIT 0
IF AGC SPEED BIT 1
PHI 1 TIME CONSTANT FOR FE
PHI 1 TIME CONSTANT FOR FE
PHI 1 TIME CONSTANT FOR AV
PHI 1 TIME CONSTANT FOR AV
FORCED SLICING LEVEL FOR VERTICAL SYNC.
SYNCHRONISATION OF OSD/TEXT DISPLAY
RGB BLANK
V-CHIP
MTS DECODING ENABLED
DEMO MODE
REAL TIME CLOCK / ON TIMER
ENERGY SAVE
PERSONAL PREFERENCE PROGRAM
UNIVERSAL PLUS
SPEAKER ON/OFF
FIXED AUDIO OUT
VIEW TIMER
FRENCH LANGUAGE
EZ SETUP / AUTOPRESET
W-TEMP
AV
WHITE TEMP OR FAVORITE COLOR
AV ENABLED OR DISABLED
AV2
DSK
RPO0
RPO1
AGN
AUTO-OFF
AV2 ENABLED OR DISABLED
DYNAMIC SKIN CONTROL
RATIO PRE- AND OVERSHOOT BIT 0
RATIO PRE- AND OVERSHOOT BIT 1
GAIN FM DEMODULATOR
AUTO SWITCH OFF ENABLED
RANGE
INITIAL VALUE FIX/ADJ
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
1
FIX*
0(disable) or1(enable)
1
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
1
FIX*
0(disable) or1(enable)
0
FIX
0(AUTOPRESET) or
1
FIX
1(EZ SETUP)
0(FC) or 1(WT)
0
FIX
0(without ext. source) or
0
FIX
1(with external source)
0(1 input) or 1(2 input)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(disable) or1(enable)
0
FIX
0(normal) or1(+6dB)
0
FIX
0(disable) or1(enable)
1
FIX
REMARK
14LK22→1/ 14MR10→0
14LK22→1/ 14MR10→0
Table - A
Holding down to short JA137 & JA138 and turn on the main power SW will automatically write the initial values into
IC1003.
This is only can done when a new EEPROM is used. (Judge with the first 4 bytes.)
ADJUSTMENT
PART REPLACED
NECESSARY
NOTES
UNNECESSARY
X
IC801
Data is stored in IC1003.
IC1003
X
Holding down to short JA137 & JA138 and turn on the main
power SW will automatically write the initial values into IC1003.
This is only can done when a new EEPROM is used. (Judge
with the first 4 bytes.)
CRT
X
Adjust items related to picture tube only.
Table - B
10
14LK22
Ë SERVICE ADJUSTMENT
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "AGC".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
CHROMA ADJUSTMENT
No. Adjusting point
1
SUB-TINT (I2C
BUS CONTROL)
Adjusting procedure/conditions
1. Receive the "Colour Bar" signal through AV in.
2. Connect the oscilloscope to TP853 (Pin (5) of
P882) BLUE-OUT.
» Range
: 100mV/div. (AC)(Use Probe 10:1)
» Sweep time : 10 µsec/div.
3. Call the "SUB-TINT" mode in service mode. Adjust the "SUB-TINT" bus data to obtain the waveform shown as Fig 1.
4. "SUB-TINT" bus data decrease 4 steps to get final
waveform. (Fig 2.)
5. Clear the SERVICE mode.
Waveform and others
WAVEFORM 1
FINAL WAVEFORM
SAME LEVEL
W Y CY G MG R B
Fig 1
Fig 2
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
No. Adjusting point
Adjusting procedure/conditions
1
V-SLOPE(I2C
BUS CONTROL)
2
V-CENTER (I2C 1. Call the "V-CENT" mode.
2. Increase or decrease "V-CENT" by Volume key till
BUS CONthe picture is centered.
TROL)
3
V - AMP (I2C
BUS CONTROL)
1. Call the "V-AMP" mode.
2. Increase or decrease "V - AMP" by Volume key to
set overscan of 10.0% typical.
Adjustment Spec 10.0% range ±1%.
4
S-CORRECTION (I2C
BUS CONTROL)
H - CENTER
FIXED DATA, NO NEED TO ADJUST.
Focus
adjustment
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Adjust the focus control to get the best focus.
5
6
1. Receive Monoscope Pattern Signal.
2. Call the "V-LIN" mode.
3. Increase or decrease "V-LIN" by Volume key till
the horizontal line in the center of monoscope is
just at the position where the blanking starts.
1. Call the "H-CENT" mode.
2. Increase or decrease "H-CENT" by Volume key
to center the picture horizontal.
11
Waveform and others
14LK22
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
No. Adjusting point
1
CRT CUTOFF
ADJUSTMENT
(I2C BUS
CONTROL)
Adjusting procedure/conditions
1. Switch TV to VIDEO mode,BLUE BACK OFF, with
NO VIDEO signal.
2. Press R/C to set Picture Normal condition.
3. Connect the oscilloscope to Red OUT from
IC801.(TP47R)
Range
Sweep
Waveform and others
3.0Vdc
: 1 V/Div (DC)
: 5 msec/Div
1V
4. Adjust SCREEN VR ,so that the tip of signal reach
3.0 Vdc + 0.1 Vdc.
2
3
SUB-BRIGHTNESS
ADJUSMENT
(I2C BUS
CONTROL)
WHITE BALANCE SERVICE MODE
ADJ. (I2C BUS
CONTROL)
1. Call " SUB-BRI" in service mode. (Receive Crosshatch pattern with 5 black level windows)
2. Adjust the " SUB BRIGHT " bus data in order that
the line 1, 2 and 3 have the same darkness
wherelse line 4 is slightly brighter than line 1, 2
and 3 and finally line 5 will be the brighter than
line 4.
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between the TP 602
( - ) TP 603 ( + ).
4. Check Beam current should be around (720µA)
5. Set it to service mode and adjust the DRI-G-MH,
& DRI-B-MH data to have a colour temperature
of 11,600°K ( white ).
6. Receive "WHITE" pattern, WITH BURST signal,
and set BRIGHTNESS Y by generator, to ** 10
cd/m2 (MINOLTA CA-100) by reducing LUMINATE
Y signal.
7. Adjust "CUT-R" & "CUT-G" to get 11,600°K. Then
go back NORMAL mode (HIGH BRIGHT**) to
check colour temperature. If out of range, back
to (1).
Note: This adjustment must be done after
warming up the unit for 30 minutes or
longer with a beam current over 500µA.
DRI-R-MH=32
DRI-G-MH=33
DRI-B-MH=37
DRI-R-MH=32
4
Maximum
beam check
(FIXED)
(FIXED)
(FIXED)
(FIXED)
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP603 (+)
and TP602 (–).
(Full Scale: 3 mA Range)
4. Beam current must be within 720 ± 50 µA.
12
0
1 2 3 4 5
1, 2, 3 are in same black level.
# 11,600° K
X : 0.273
Y : 0.280
( MINOLTA COLOUR ANALYZER
CA-100)
*NOTE: Above DATA can be UP/
DOWN by volume key.
14"
LOW
1.8cd/m2
HIGH
115cd/m2
* 11,600° K
DRI-GW="DRI-GS"DATA-5
DRI-BW="DRI-BS" DATA-5
14LK22
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
1
2
3
4
13
5
6
14LK22
BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
2
3
4
14
5
6
14LK22
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
6. indicates hot ground.
å AND SHADED (
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
) COMPONENTS
= SAFETY RELATED PARTS.
' MARK= X-RAY RELATED PARTS.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
WAVEFORMS
11.00Vp-p
Horiz Rate
667Vp-p
Horiz Rate
q8.40Vp-p
Horiz Rate
22.8Vp-p
Horiz Rate
780Vp-p
Horiz Rate
w48.8Vp-p
Vert Rate
32.6Vp-p
Horiz Rate
83.00Vp-p
Vert Rate
e98Vp-p
Horiz Rate
15
42.7Vp-p
Horiz Rate
92.3Vp-p
Horiz Rate
r1200Vp-p
Horiz Rate
565Vp-p
Horiz Rate
0116Vp-p
Horiz Rate
t415Vp-p
Power Supply Rate
SCHEMATIC DIAGRAM: MAIN Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
16~17
12
13
14
15
16
17
18
19
20
14LK22
SCHEMATIC DIAGRAM: CRT Units
H
G
F
E
D
C
B
A
1
2
3
4
18
5
6
14LK22
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
C
PWB-B: CRT Unit (Chip Parts Side)
B
A
1
2
3
4
19
5
6
14LK22
H
G
F
E
D
C
B
A
PWB-A: MAIN Unit (Wiring Side)
1
2
3
4
20
5
6
14LK22
H
G
F
E
D
C
B
A
PWB-A: MAIN Unit (Chip Parts Side)
1
2
3
4
21
5
6
14LK22
Ref. No.
Part No.
★
Description
PARTS LIST
Code
Ref. No.
TUNER
NOTE : THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU201 VTUENV56D82-1
J Tuner
or
VTUVTST5UF770
"HOW TO ORDER REPLACEMENT PARTS"
4. DESCRIPTION
AZ
INTEGRATED CIRCUITS
To have your order filled promptly and correctly, please furnish the
following informations.
3. PART NO.
Code
MAIN UNIT
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
2. REF. NO.
Description
PWB-A: DUNTKA541WEA1
PARTS REPLACEMENT
1. MODEL NUMBER
★
Part No.
IC302
å IC501
IC601
IC701
IC801
IC1003
VHiAN7511//-1
VHiANSS22++-1
VHiKA7808AP-1
VHiSTRG5653-1
RH-iX3564CEZZ
VHiBR24C02F1E
or
VHiBR24C02/-1
J
X
J
X
X
J
An7511
An5522
Kia7808api
Strg5653
I.C.
I.C.
AK
AK
AE
AQ
AX
AF
Br24c02
★ MARK : SPARE PARTS-DELIVERY SECTION
TRANSISTORS
' MARK : X- RAY RELATED PARTS
Ref. No.
Part No.
★
Description
You can substitute "VS2SC2462-C-1" for "VS2SD601AR/-1".
Q201 VS2SC2735//1E
J C2735
AC
Q253 VS2SD601A//-1
J D601A
AC
Q254 VS2SD601A//-1
J D601A
AC
Q601 VS2SC3207//-1
J C3207
AC
Q602 VS2SD2586//1E
J D2586
AM
Q603 VS2SC3198-G-1
J C3198-G
AA
Q751 VS2SC3198-G-1
J C3198-G
AA
Q752 VS2SC3198-G-1
J C3198-G
AA
Q801 VS2SB709A//-1
J B709A
AA
Q802 VS2SB709A//-1
J B709A
AA
Code
PICTURE TUBE
VB37GDA86X/1E
or
VB370BVBK1S-S
or
VB34JFQ90X/*S
or
VB34KPU02X/*S
or
VB34JLL90X/*S
or
VB34LRQ90X/*S
å L703
RCiLG0068PEZZ
å DY601 RCiLH0225PEZZ
PMAGF3041CEZZ
å
V101
R Picture Tube
R Degaussing Coil
R Deflection Yoke
J Degaussing Coil
-Purity and Static
Convergence
PSPAG0004PEZZ R Wedge(Gum), Yoke
QEARC1436PEZZ R Grounding Strap
MSPRT0001PEFJ R Spring for CRT
CB
DIODES
D201
D302
å D331
D501
D502
D503
D505
D508
D509
D531
D532
D601
å D602
å D603
å D606
å D608
D651
D653
D701
D705
D706
D707
å D751
å D752
D754
D755
D801
D802
D803
D804
D805
D806
D1001
D1004
D1012
D1018
D1019
D1020
D1021
AH
BA
AG
AB
AE
AC
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-A DUNTKA541WEA1 – MAIN Unit
PWB-B DUNTKA542WEA0 – CRT Unit
—
—
22
RH-EX0676GEZZ
VHD1SS119//-1
RH-DX0302CEZZ
VHD1SS119//-1
RH-EX0615GEZZ
VHD1SS119//-1
RH-DX0441CEZZ
RH-DX0131CEZZ
RH-EX0665GEZZ
RH-EX0627GEZZ
RH-EX0627GEZZ
RH-DX0475CEZZ
VHD1SS244//-1
RH-EX0667GEZZ
RH-DX0131CEZZ
RH-DX0468CEZZ
RH-EX0627GEZZ
VHD1SS119//-1
RH-DX0476CEZZ
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
RH-DX0229CEZZ
RH-DX0131CEZZ
RH-EX0616GEZZ
RH-EX0603GEZZ
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
RH-PX0013PEZZ
VHD1SS119//-1
RH-EX0611GEZZ
RH-EX0263TAZZ
RH-EX0263TAZZ
RH-EX0263TAZZ
RH-EX0263TAZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
R
J
J
J
J
J
J
Zener Diode, 33V
Diode
Diode
Diode
Zener Diode, 5V
Diode
Diode
Diode
Zener Diode, 24V
Zener Diode, 8.2V
Zener Diode, 8.2V
Diode
Diode
Zener Diode, 27V
Diode
Diode
Zener Diode, 8.2V
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Zener Diode, 5.6V
Zener Diode, 3.9V
Diode
Diode
Diode
Diode
Diode
Diode
Photodiode
Diode
Zener Diode, 5.1V
Zener Diode, 8.3V
Zener Diode, 8.3V
Zener Diode, 8.3V
Zener Diode, 8.3V
AA
AB
AC
AB
AA
AB
AC
AC
AA
AA
AA
AB
AB
AA
AC
AE
AA
AB
AG
AC
AC
AC
AF
AC
AA
AA
AB
AB
AB
AB
AB
AB
AC
AB
AA
AB
AB
AB
AB
14LK22
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA541WEA1
C531
C532
C533
C601
C602
C603
C604
C605
C606
C607
C608
C610
C611
C612
C620
C640
C651
C652
C653
C654
C655
C656
C657
C658
C701
MAIN UNIT (Continued)
D1022 RH-EX0263TAZZ
D1023 RH-EX0263TAZZ
å VA701 RH-VX0073CEZZ
J Zener Diode, 8.3V
J Zener Diode, 8.3V
X Varistor
AB
AB
AF
PACKAGED CIRCUITS
PR702 RMPTP0028CEZZ J Packaged Circuit
X1001 RCRSB0300CEZZ J Crystal
AG
AF
FILTERS
CF253 RFiLC0446CEZZ
SF201 RFiLC0405CEZZ
J Filter
J S.A.W. Filter
AD
AH
COILS
L202
L203
L204
L253
å L701
å L751
L802
L803
L1030
L1050
L1051
VP-DF270K0000
VP-DF270K0000
VP-XF1R2K0000
VP-XF120K0000
RCiLF0096PEZZ
RCiLP0225CEZZ
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
J
J
J
J
R
J
J
J
J
J
J
Peaking 27µH
Peaking 27µH
Peaking 1.2µH
Peaking 12µH
Coil
Coil
Peaking 10µH
Peaking 10µH
Peaking 10µH
Peaking 10µH
Peaking 10µH
AB
AB
AB
AB
AF
AF
AB
AB
AB
AB
AB
C702
C703
C704
C705
C709
C710
C711
C712
C751
å C752
å C753
å C754
å C755
å C756
C759
C760
C801
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C812
C813
C814
C816
C1001
C1002
C1003
C1004
C1005
C1006
C1008
C1009
C1010
C1011
C1012
C1013
C1016
C1018
C1024
C1026
TRANSFORMERS
å
å
T601
T602
å
T701
RTRNZ0144PEZZ R Transformer
RTRNF0228PEZZ X H-Volt Transformer
or
RTRNF0230PEZZ
RTRNW0015PEZZ X Transformer
AE
AV
AK
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C201 VCEA0A1CW476M J 47
16V EL.
C202 VCEA0A1AW337M+X 330
10V EL.
C205 VCKYCY1HF103Z J 0.01 50V Ceramic
C206 VCEA0A1HW105M J 1.0
50V EL.
C207 VCKYCY1HB103K J 0.01 50V Ceramic
C208 VCKYCY1HB103K J 0.01 50V Ceramic
C209 VCKYCY1HB103K J 0.01 50V Ceramic
C210 VCKYCY1HF103Z J 0.01 50V Ceramic
C211 VCKYCY1HF103Z J 0.01 50V Ceramic
C231 VCKYCY1HF223Z J 0.022 50V Ceramic
C232 VCKYCY1HB821K J 820p 50V Ceramic
C233 VCKYCY1HB472K J 4700p 50V Ceramic
C234 VCKYCY1EF104Z J 0.1
25V Ceramic
C251 VCKYCY1HF223Z J 0.022 50V Ceramic
C252 VCEA0A1CW107M J 100
16V EL.
C301 VCEA0A1CW477M J 470
16V EL.
C304 VCEA0A1HW106M J 10
50V EL.
C310 VCEA0A1HW225M J 2.2
50V EL.
C312 VCEA0A1HW225M J 2.2
50V EL.
C313 VCKYCY1HB332K J 3300p 50V Ceramic
å C332
VCQYTA1HM103J J 0.01 50V Mylar
å C333
VCEA0A1CW108M J 1000 16V EL.
C356 VCKYCY1HB472K J 4700p 50V Ceramic
C359 VCEA0A1CW106M J 10
16V EL.
C360 VCEA0A1HW225M J 2.2
50V EL.
C409 VCKYCY1EF104Z J 0.1
25V Ceramic
C410 VCKYCY1EF104Z J 0.1
25V Ceramic
C411 VCKYCY1HB102K J 1000p 50V Ceramic
C501 VCKYPA1HB102K J 1000p 50V Ceramic
C504 VCKYCY1HB103K J 0.01 50V Ceramic
C505 VCEA0A1HW107M J 100
50V EL.
C507 VCKYCY1HB103K J 0.01 50V Ceramic
C508 VCFYSA1JB224J+ X 0.22 63V Ceramic
C509 VCEA0A1CW477M J 470
16V EL.
C510 VCKYPA2HB102K J 1000p 500V Ceramic
C514 VCFYSA1JB563J+ X 0.056 63V Ceramic
AB
AE
AA
AB
AA
AA
AA
AA
AA
AB
AA
AA
AA
AB
AC
AC
AB
AB
AB
AA
AA
AD
AA
AB
AB
AA
AA
AA
AA
AA
AB
AA
AF
AC
AA
AE
23
Part No.
VCKYCY1HB102K
VCKYCY1HB102K
VCQYTA1HM104J
VCQYTA1HM563J
VCEA0A1HW475M
VCEA0A1HW105M
VCEA0A2EW106M
VCKYPA2HB102K
VCFPVC2DB334J
VCFPVC3ZA532H
VCKYPA2HB102K
VCEA0A1CW108M
VCEA0A1EW476M
VCEA0A1CW477M
VCKYPA2HB102K
VCFYSB2EB823J
VCQYTA1HM222J
VCQYTA1HM472J
VCEA0A1HW105M
VCKYCY1HF223Z
VCEA0A1HW106M
VCEA0A1HW224M
VCKYCY1EF104Z
VCKYCY1EF104Z
RC-FZ036SCEZZ
or
RC-FZ035SGEZZ
or
RC-FZ038SCEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-EZ1044CEZZ
RC-KZ0039CEZZ
VCEA0A1HW476M
VCKYPA1HB102K
VCKYPA1HB471K
RC-KZ0092GEZZ
VCKYPH3DB561K
RC-EZ0724CEZZ
RC-EZ0638CEZZ
VCEA0A1CW108M
VCQYTA1HM103J
VCEA0A0JW477M
VCEA0A0JW228M
VCEA0A1HW105M
VCEA0A1CW337M
VCEA0A1CW107M
VCKYCY1HB222K
VCKYD41HB102K
VCKYD41HB102K
VCKYD41HB102K
VCEA0A1CW107M
VCKYCY1CF474Z
VCKYCY1CF474Z
VCEA0A1CW107M
VCFYFA1HA224J
VCFYFA1HA224J
VCKYCY1HB471K
VCKYCY1HB471K
VCEA0A0JW107M
VCEA0A0JW107M
VCEA0A1CW106M
VCKYCY1CF474Z
VCKYCY1CF474Z
VCEA0A1CW106M
VCCCCY1HH330J
VCCCCY1HH330J
VCEA0A0JW107M
VCKYCY1CF474Z
VCKYCY1CF474Z
VCEA0A0JW107M
VCQYTA1HM104J
VCKYCY1HB221K
VCQYTA1HM104J
VCEA0A0JW107M
★
Description
Code
J
J
J
J
J
J
J
J
J
X
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
1000p
1000p
0.1
0.056
4.7
1.0
10
1000p
0.33
5300p
1000p
1000
47
470
1000p
0.082
2200p
4700p
1.0
0.022
10
0.22
0.1
0.1
0.1
50V
50V
50V
50V
50V
50V
250V
500V
200V
1.5kV
500V
16V
25V
16V
500V
250V
50V
50V
50V
50V
50V
50V
25V
25V
275V
Ceramic
Ceramic
Mylar
Mylar
EL.
EL.
EL.
Ceramic
M-Poly.
M-Poly.
Ceramic
EL.
EL.
EL.
Ceramic
Ceramic
Mylar
Mylar
EL.
Ceramic
EL.
EL.
Ceramic
Ceramic
Ceramic
AA
AA
AA
AB
AB
AB
AD
AA
AD
AF
AA
AD
AB
AC
AA
AD
AA
AB
AB
AB
AB
AB
AA
AA
AC
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0.01
0.01
0.01
150
680P
47
1000p
470p
0.0033
560p
100
33
1000
0.01
470
2200
1.0
330
100
2200p
1000p
1000p
1000p
100
0.47
0.47
100
0.22
0.22
470p
470p
100
100
10
0.47
0.47
10
33p
33p
100
0.47
0.47
100
0.1
220p
0.1
100
250V Ceramic
250V Ceramic
250V Ceramic
400V EL.
2kV Ceramic
50V EL.
50V Ceramic
50V Ceramic
AC250V Ceramic
2kV Ceramic
160V EL.
160V EL.
16V EL.
50V Mylar
6.3V EL.
6.3V EL.
50V EL.
16V EL.
16V EL.
50V Ceramic
50V Ceramic
50V Ceramic
50V Ceramic
16V EL.
16V Ceramic
16V Ceramic
16V EL.
50V Mylar
50V Mylar
50V Ceramic
50V Ceramic
6.3V EL.
6.3V EL.
16V EL.
16V Ceramic
16V Ceramic
16V EL.
50V Ceramic
50V Ceramic
6.3V EL.
16V Ceramic
16V Ceramic
6.3V EL.
50V Mylar
50V Ceramic
50V Mylar
6.3V EL.
AC
AC
AC
AM
AB
AB
AA
AA
AC
AC
AG
AG
AD
AA
AC
AD
AB
AC
AC
AA
AA
AA
AA
AC
AB
AB
AC
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AA
AA
AA
AB
14LK22
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKA541WEA1
R432
R501
R502
R503
R504
R505
R506
R507
R510
R511
R512
R521
R531
R532
R533
R601
R602
R603
R604
R605
å R606
å R607
å R609
å R610
R611
R612
R613
å R614
R615
R616
R618
R619
R620
R622
R625
R626
R641
R651
R652
R653
R654
R655
R656
R658
R663
R701
R707
R708
R709
R710
R711
R712
R716
R751
R752
å R753
R754
R755
R756
R757
R801
R802
R803
R804
R805
R806
R807
R808
R809
R812
R813
R1002
R1003
R1006
R1007
R1008
MAIN UNIT (Continued)
RESISTORS
RJ2
RJ4
RJ8
RJ9
RJ10
RJ13
RJ14
RJ15
RJ16
RJ17
RJ19
RJ21
RJ26
RJ28
RJ31
RJ32
RJ35
RJ37
RJ38
RJ41
RJ42
RJ43
RJ46
RJ49
RJ50
RJ51
RJ52
RJ53
RJ70
RJ71
RJ72
RJ73
RJ75
R201
R202
R205
R206
R207
R208
R209
R212
R216
R219
R220
R231
R232
R233
R234
R257
R258
R259
R260
R261
R262
R263
R301
R304
R310
R311
R313
R314
R315
R320
R333
R334
R335
R364
R431
[M-Ox.··· Metal Oxide, Metal Film··· M-Film]
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF101J
J 100 1/16W M-Ox.
VRS-CY1JF101J
J 100 1/16W M-Ox.
VRS-CY1JF680J
J 68 1/16W M-Ox.
VRS-CY1JF122J
J 1.2k 1/16W M-Ox.
VRS-CY1JF221J
J 220 1/16W M-Ox.
VRS-CY1JF122J
J 1.2k 1/16W M-Ox.
VRS-CY1JF392J
J 3.9k 1/16W M-Ox.
VRS-CY1JF332J
J 3.3k 1/16W M-Ox.
VRS-RG3LB223J+ X 22k 3W
M-Ox.
VRD-RA2BE392J J 3.9k 1/8W
Carbon
VRS-CY1JF221J
J 220 1/16W M-Ox.
VRD-RA2BE681J J 680 1/8W
Carbon
VRS-CY1JF272J
J 2.7k 1/16W M-Ox.
VRS-CY1JF101J
J 100 1/16W M-Ox.
VRS-CY1JF391J
J 390 1/16W M-Ox.
VRS-CY1JF181J
J 180 1/16W M-Ox.
VRS-CY1JF151J
J 150 1/16W M-Ox.
VRS-CY1JF471J
J 470 1/16W M-Ox.
VRS-CY1JF392J
J 3.9k 1/16W M-Ox.
VRS-CY1JF223J
J 22k 1/16W M-Ox.
VRS-CY1JF560J
J 56 1/16W M-Ox.
VRS-CY1JF560J
J 56 1/16W M-Ox.
VRS-CY1JF101J
J 100 1/16W M-Ox.
VRS-CY1JF683J
J 68k 1/16W M-Ox.
VRS-CY1JF473J
J 47k 1/16W M-Ox.
VRS-CY1JF473J
J 47k 1/16W M-Ox.
VRS-CY1JF102J
J 1.0k 1/16W M-Ox.
VRS-CY1JF103J
J 10k 1/16W M-Ox.
VRS-CY1JF392J
J 3.9k 1/16W M-Ox.
VRN-RL3DB4R7J+ X 4.7 2W
M-Film
VRS-CY1JF101J
J 100 1/16W M-Ox.
VRS-CY1JF332J
J 3.3k 1/16W M-Ox.
VRS-CY1JF564J
J 560k 1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF101J
J 100 1/16W M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AF
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
24
Part No.
VRS-CY1JF750J
VRD-RA2BE272J
VRD-RM2HD102J
VRN-RL3DB2R7J+
VRS-CY1JF181J
VRS-CY1JF102J
VRS-RG3AB331J+
VRN-RL3AB1R0J+
VRD-RA2BE333J
VRS-CY1JF181J
VRD-RM2HD100J
VRD-RA2BE333J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE393J
VRS-RG2HC102J
VRD-RA2BE393J
VRD-RA2BE273J
VRD-RA2BE563J
VRD-RM2HD124J
VRN-RL3AB1R5J+
VRD-RM2HD270J
VRD-RA2BE154J
VRD-RA2BE102G
VRS-CY1JF102J
VRS-CY1JF123J
VRS-CY1JF103J
VRD-RM2HD100J
VRS-RG3DB682J+
VRN-RL3ABR47J+
VRS-RG3DB391J+
VRS-RG3LB103J+
VRS-RG3AB472J+
VRD-RA2BE102J
VRN-VV3DB8R2J
VRD-RM2HD470J
VRN-RL2HCR47J+
VRS-CY1JF223J
VRS-CY1JF102J
VRS-CY1JF822J
VRS-CY1JF273J
VRS-CY1JF391J
VRS-CY1JF100J
VRD-RA2BE101J
VRD-RA2BE101J
VRW-KQ3NC3R9K
VRS-VV3DB104J
VRD-RA2BE681J
VRN-RL3DBR47J+
VRN-RL3DBR56J+
VRD-RA2BE682J
VRD-RA2BE152J
VRD-RA2BE562J
RR-DZ0049CEZZ
RR-DZ0049CEZZ
VRD-RM2HD124J
VRD-RM2HD150J
VRD-RA2BE221J
VRD-RM2HD270J
VRS-CY1JF151J
VRS-CY1JF221J
VRS-CY1JF221J
VRS-CY1JF221J
VRS-CY1JF221J
VRS-CY1JF822J
VRD-RA2BE123J
VRS-CY1JF103J
VRS-CY1JF221J
VRD-RA2BE224J
VRS-CY1JF101J
VRS-CY1JF221J
VRS-CY1JF822J
VRS-CY1JF562J
VRS-CY1JF562J
VRS-CY1JF562J
VRS-CY1JF822J
★
J
J
J
X
J
J
X
X
J
J
J
J
J
J
J
J
J
J
J
J
X
J
J
J
J
J
J
J
X
X
X
X
X
J
J
J
X
J
J
J
J
J
J
J
J
J
J
J
X
X
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
75 1/16W
2.7k 1/8W
1.0k 1/2W
2.7 2W
180 1/16W
1.0k 1/16W
330 1W
1.0 1W
33k 1/8W
180 1/16W
10 1/2W
33k 1/8W
100 1/16W
100 1/16W
39k 1/8W
1.0k 1/2W
39k 1/8W
27k 1/8W
56k 1/8W
120k 1/2W
1.5 1W
27 1/2W
150k 1/8W
1.0k 1/8W
1.0k 1/16W
12k 1/16W
10k 1/16W
10 1/2W
6.8k 2W
0.47 1W
390 2W
10k 3W
4.7k 1W
1.0k 1/8W
8.2 2W
47 1/2W
0.47 1/2W
22k 1/16W
1.0k 1/16W
8.2k 1/16W
27k 1/16W
390 1/16W
10 1/16W
100 1/8W
100 1/8W
3.9 7W
100k 2W
680 1/8W
0.47 2W
0.56 2W
6.8k 1/8W
1.5k 1/8W
5.6k 1/8W
3.9M 1/2W
3.9M 1/2W
120k 1/2W
15 1/2W
220 1/8W
27 1/2W
150 1/16W
220 1/16W
220 1/16W
220 1/16W
220 1/16W
8.2k 1/16W
12k 1/8W
10k 1/16W
220 1/16W
220k 1/8W
100 1/16W
220 1/16W
8.2k 1/16W
5.6k 1/16W
5.6k 1/16W
5.6k 1/16W
8.2k 1/16W
M-Ox.
Carbon
Carbon
M-Film
M-Ox.
M-Ox.
M-Ox.
M-Film
Carbon
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Film
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Film
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Film
Carbon
M-Film
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Cement
M-Ox.
Carbon
M-Film
M-Film
Carbon
Carbon
Carbon
Solid
Solid
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Code
AA
AA
AA
AE
AA
AA
AE
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AE
AA
AA
AB
AA
AA
AA
AA
AE
AE
AE
AE
AE
AA
AB
AA
AE
AA
AA
AA
AA
AA
AA
AB
AB
AE
AB
AA
AE
AE
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
14LK22
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA541WEA1
VRS-CY1JF562J
VRS-CY1JF332J
VRD-RA2BE391J
VRD-RA2BE101J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF183J
VRS-CY1JF101J
VRS-CY1JF221J
VRS-CY1JF183J
VRS-CY1JF101J
VRS-CY1JF224J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF223J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE471J
VRS-CY1JF101J
VRS-CY1JF332J
VRS-CY1JF392J
VRS-CY1JF683J
VRS-CY1JF472J
VRS-CY1JF101J
VRS-CY1JF101J
S1001
S1002
S1003
S1004
S1005
S1006
QSW-K0003AJZZ
QSW-K0003AJZZ
QSW-K0003AJZZ
QSW-K0003AJZZ
QSW-K0003AJZZ
QSW-K0114CEZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
5.6k
3.3k
390
100
100
3.3k
100
3.3k
100
18k
100
220
18k
100
220k
100
3.3k
100
3.3k
3.3k
100
100
22k
100
100
470
100
3.3k
3.9k
68k
4.7k
100
100
1/16W
1/16W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
CH-up
CH-down
Vol-up
Vol-down
Picture/Preset
Power
QFS-C3229CEZZ
RBLN-0091GEZZ
QFSHD1013CEZZ
QFSHD1014CEZZ
QJAKE0210CE04
QJAKE0210CE09
QJAKF0074CEZZ
QPLGN0241CEZZ
QPLGN0660CEZZ
QPLGN0361CEZZ
QPLGN0260CEZZ
QPLGN0269GEZZ
QPLGN0561CEZZ
RRMCU0222CEZZ
LHLDW1104PEZZ
LHLDW1105PEZZ
LX-BZ0086TAFD
LX-BZ3049GEFD
LX-TZ3004CEFD
RDA501 PRDAR0118GJFW
RDA701 PRDAR0298PEFW
J
X
J
J
X
X
X
J
J
J
J
J
J
J
X
X
J
J
J
X
R
Fuse, 3.15A
Ferrite Bead
Fuse Holder
Fuse Holder
Jack, Video-IN
Jack, Audio-IN
Jack, AV-IN(REAR)
Plug, 2pin (S)
Plug, 6pin (F)
Plug, 3pin (TP651-3)
Plug, 2pin (M)
Plug, 2pin (K701-2)
Plug, 5pin (BC)
R/C Receiver
H-wire Holder
K-wire Holder
Screw
Screw
Screw
Heat Sink for IC501
Heat Sink for IC701
Q870
Q871
Q872
Q883
Q885
Q887
RH-TX0110BMZZ+
RH-TX0110BMZZ+
RH-TX0110BMZZ+
RH-TX0124BMZZ+
RH-TX0124BMZZ+
RH-TX0124BMZZ+
D881
D882
D883
D884
D885
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
X
X
X
X
X
X
TX0110BM
TX0110BM
TX0110BM
TX0124BM
TX0124BM
TX0124BM
AE
AE
AE
AE
AE
AE
DIODES
J
J
J
J
J
Diode
Diode
Diode
Diode
Diode
AB
AB
AB
AB
AB
CAPACITORS
C871
C872
C873
C875
C876
C878
C880
C881
C882
C886
[EL.··· Electrolytic]
VCCSCY1HL471J J 470p 50V
VCCSCY1HL471J J 470p 50V
VCCSCY1HL471J J 470p 50V
VCKYPA2HB102K J 1000p 500V
RC-KZ0150CEZZ J 1000p 3kV
VCEA0A2EW106M J 10
250V
VCCSCY1HL471J J 470p 50V
VCKYPA1HB471K J 470p 50V
VCKYPA1HB471K J 470p 50V
VCKYPA2HB102K J 1000p 500V
R879
R880
R881
R882
R883
R884
R885
R886
R887
R888
R892
R893
R894
R898
R899
[M-Ox.··· Metal Oxide]
VRS-CY1JF471J
J 470 1/16W
VRS-CY1JF471J
J 470 1/16W
VRS-CY1JF471J
J 470 1/16W
VRS-VU3DE153J J 15k 2W
VRD-RM2HD272J J 2.7k 1/2W
VRS-VU3DE153J J 15k 2W
VRD-RM2HD272J J 2.7k 1/2W
VRS-VU3DE153J J 15k 2W
VRD-RM2HD272J J 2.7k 1/2W
VRS-CY1JF471J
J 470 1/16W
VRS-CY1JF102J
J 1.0k 1/16W
VRS-CY1JF102J
J 1.0k 1/16W
VRS-CY1JF102J
J 1.0k 1/16W
VRS-CY1JF471J
J 470 1/16W
VRS-CY1JF471J
J 470 1/16W
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Ceramic
Ceramic
Ceramic
Ceramic
AA
AA
AA
AA
AB
AD
AA
AA
AA
AA
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AB
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
RESISTORS
AB
AB
AB
AB
AB
AE
MISCELLANEOUS PARTS
F701
FB601
FH701
FH702
J402
J403
J409
P302
P601
P603
P701
P702
P1002
RMC1001
Code
TRANSISTORS
SWITCHES
J
J
J
J
J
J
Description
PWB-B: DUNTKA542WEA0
CRT UNIT
MAIN UNIT (Continued)
R1009
R1011
R1012
R1013
R1014
R1015
R1016
R1017
R1020
R1021
R1022
R1023
R1024
R1025
R1026
R1028
R1032
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
R1046
R1047
R1050
R1051
R1066
R1072
R1073
★
Part No.
AD
AC
AC
AC
AF
AF
AG
AA
AC
AB
AC
AB
AB
AL
AE
AE
AA
AA
AA
AE
AF
MISCELLANEOUS PARTS
SC881 QSOCV0842CEZZ J CRT Socket
P882 QCNW-2608PEZZ X Connecting Cord(K-wire)
P884 QCNW-2609PEZZ X Connecting Cord(H-wire)
25
AH
AG
AG
14LK22
Ref. No.
Part No.
★
Description
Code
Ref. No.
MISCELLANEOUS PARTS
å
ACC701 QACCZ3008PEZZ J AC Cord
SP301 VSP0080PBQ9YA X Speaker, 32 ohm
QCNW-2206PEZZ R Connecting Cord
★
Part No.
Description
CABINET PARTS
AN
AH
AD
1
1-1
1-2
1-3
1-4
1-5
CCABA0133WEH0
Not Available
JBTN-0112GJSA
MSPRC0005PEFW
JBTN-0111GJSA
HDECQ0102GJSA
X
–
X
R
X
X
Front Cabinet Ass'y
Front Cabinet
Power Button
Power Spring
Control Button
Cover for R/C
2
GCABB0124GJKA X Rear Cabinet
SUPPLIED ACCESSORIES
TiNS-7400GJZZ
X Operation Manual
RRMCG1339CESB X Infrared R/C Unit
QPLGA0017CEZZ J Plug
AN
AP
AK
PACKING PARTS
CABINET PARTS LOCATION
(NOT REPLACEMENT ITEM)
SPAKC0206GJZZ
SPAKP0104GJZZ
SPAKX0123GJZZ
– Packing Case
– Wrapping Paper
– Buffer Material
Code
—
—
—
1
1-2 1-3
26
2
1-1
1-5
1-4
—
AB
14LK22
Ref. No.
Part No.
★
Description
Code
Ref. No.
Part No.
PACKING OF THE SET
★
Description
★ Polyethylene Bag
Operation Manual
Infrared R/C Unit
★ Batteries
★ Wrapping Paper
★ Buffer Material
FRONT
★ Packing Case
Use tape to fix
top side of pack
case.
REAR
Use 12 staples fix
the packing case.
★ MARK : Not Replacement Items.
27
Code
14LK22
COPYRIGHT © 2001 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
D SEM P SEMEX TQ1196-S
Aug. 2001 Printed in Japan
MI. KD
28