Majestic fireplaces CVR36 Operating instructions

Decorative Gas Appliance
Models: NVSTR36
NVCVR36
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE.
IMPORTANT: Read all instructions
and warnings carefully before starting installation. Failure to follow these
instructions may
result in a possible fire hazard
and will void the warranty.
WARNING: If the information in
this manual is not followed
exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
FOR YOUR SAFETY:
Installation and service must be performed by a qualified installer, service
agency, or the gas supplier. Do not
store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
FOR YOUR SAFETY,
if you smell gas:
1. Open windows.
2. Do not touch electrical switches.
3. Do not try to light any appliance.
4. Extinguish any open flame.
5. Do not use the phone in your building.
6. Immediately call your gas supplier
from a neighbor's phone.
7. Follow your gas supplier's instructions.
8. If you cannot reach your gas supplier, call the fire department.
NVSTR36
NVCVR36
FP653_NVSTR_NVCVR_nu_cvr
Homeowner's Installation and
Operating Manual
3/28/98
rev. 08-20-02
rjs
DE S I GN�
CE
RTIFIED
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
7412958 7/06 Rev. 9
NVSTR/ NVCVR Series
Table of Contents
Thank you, and Congratulations on your purchase of a CFM Corporation Fireplace.
PLEASE READ THESE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THE APPLIANCE.
IMPORTANT:Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Installation & Operating Instructions
General Information............................................................................................................. 3
Description .......................................................................................................................... 3
Fireplace Framing and Specification Dimensions ............................................................... 4
Clearance to Combustibles ................................................................................................. 5
Mantels ............................................................................................................................... 5
Hearth Extension ................................................................................................................. 5
Insulating for Cold Climates ................................................................................................ 5
Framing and Finishing ......................................................................................................... 6
Finishing .............................................................................................................................. 6
Gas Specifications............................................................................................................... 6
Gas Inlet & Manifold Pressures ........................................................................................... 6
High Elevations .................................................................................................................. 6
Parts Identification and Chase Installation .......................................................................... 7
Gas Line Installation ............................................................................................................ 8
Remote Wall Switch ............................................................................................................ 8
EB-1 Electrical Box.............................................................................................................. 9
Install the Venting System, Flashing and Termination ......................................................... 9
Venting Runs ..................................................................................................................... 10
Operating Instructions
Glass Information .............................................................................................................. 11
Glass Cleaning .................................................................................................................. 11
Log Installation .................................................................................................................. 11
Ember Material Placement ................................................................................................ 11
Lava Rock ......................................................................................................................... 11
First Firing ........................................................................................................................ 11
Flame Adjustment.............................................................................................................. 12
Flame Characteristics........................................................................................................ 12
Inspect the Venting System ............................................................................................... 12
Lighting and Operating Instructions .................................................................................. 13
Troubleshooting ................................................................................................................. 15
Maintenance
Cleaning the Standing Pilot Control System .................................................................... 17
Cleaning Automatic Direct Electronic Ignition System ...................................................... 17
Replacement Parts ...................................................................................................................... 18
Accessories ................................................................................................................................. 21
Warranty ....................................................................................................................................... 23
2
7412958
NVSTR/ NVCVR Series
Installation & Operating Instructions
This gas appliance should be installed by a qualified installer in accordance with local building codes and with
current CSA-B149.1 Installation codes for Gas Burning
Appliances and Equipment.
FOR U.S.A. Installations follow local codes and/or the
current National Fuel Gas Code. ANSI Z223.1/NFPA
54.
In the Commonwealth of Massachusetts, all gas fittings
and installation of this heater shall only be done by a
licensed gas fitter or licensed plumber
FOR SAFE INSTALLATION AND OPERATION OF
YOUR NATURAL DRAFT APPLIANCE PLEASE NOTE
THE FOLLOWING:
1. This appliance gives off high temperatures and should be
located out of high traffic areas and away from furniture
and draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this appliance and should
stay away to avoid burns or ignition of clothing.
3. Children should be carefully supervised when they are in
the same room as your appliance.
4. Under no circumstances should this appliance be modified. Parts having to be removed for servicing should be
replaced prior to operating this appliance again.
5. Installation and any repairs to this appliance should be
carried out by a qualified service person. A professional
service person should be contacted to inspect this appliance annually. Make it a practice to have all of your gas
appliances checked annually. More frequent cleaning may
be required due to excess lint and dust from carpeting,
bedding material, etc.
6. Control compartments, burners and air passages in this
appliance should be kept clean and free of dust and lint.
Make sure that the gas valve and pilot light are turned off
before you attempt to clean this unit.
7. The venting system (chimney) of this appliance should be
checked at least once a year and if needed your venting
system should be cleaned.
8. Keep the area around your appliance clear of combustible
materials, gasoline and other flammable vapor and liquids.
This appliance should not be used as a drying rack for
clothing, nor should Christmas stockings or decorations be
hung in the area of it.
9. Under no circumstances should any solid fuels (wood,
coal, paper or cardboard etc.) be used in this appliance.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
11. Whether the appliance is installed directly on carpeting,
vinyl tile or any combustible material other than wood,
this appliance must be installed on a metal or wood panel
extending the full width and depth of the appliance.
12. This appliance requires adequate ventilation and combustion air to operate properly.
Description
NVSTR / NVCVR Series are radiant, natural draft appliances and use a 6" B-vent system. Do not burn wood
or other materials in these appliances. Each model is
available with standing pilot or electronic ignition for use
with Natural or Propane gas units.
Report to your dealer any parts damaged in shipment.
Adequate combustion and ventilation air must be provided. The flow of combustion and ventilation air MUST
NOT be obstructed.
Provide adequate clearances around the air opening
into the combustion chamber; and adequate accessibility clearance for servicing and proper operation. NEVER
obstruct the front opening of the appliance.
The 6" vent system MUST connect to the appliance and
terminate out-of-doors in a vertical position and terminate with a B-vent cap.
This appliance must not be connected to a chimney flue
servicing a separate solid-fuel burning appliance.
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known
to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
IMPORTANT:
PLEASE READ THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace “ON”.
It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle. Similar noises are found
with your furnace heat exchanger or car engine.
It is not unusual for your gas fireplace to give off
some odor the first time it is burned. This is due to the
curing of the paint and any undetected oil used in the
manufacturing process.
Please ensure that your room is well ventilated.
Open all windows.
It is recommended that you burn your fireplace for at
least ten (10) continuous hours the first time you use
it. If the optional fan kit has been installed, place the
fan switch in the “OFF” position during this time.
WARNING: Check with your electronics manufacturer before installing a television or other electronic
device above this fireplace.
7412958
3
NVSTR/ NVCVR Series
NVSTR36 Series Gas Appliance, See Through Model
Rough
Opening
Depth
6" DIA.
�����"
(578mm)
���" Recessed
(16mm) Nailing
Flange
Rough Opening Width 41"
(1041mm)
Rough
Opening
Height
����"
(191mm)
40���"
(1029mm)
Outside
36"
(914mm) Air
Electrical
Access
��"
(533mm)
36"
(914mm)
�"
(203mm)
��"
(279mm)
��"
(305mm)
Gas Line
Access
����"
(191mm)
����"
(165mm)
40���"
(1029mm)
3���"
(79mm)
3���"
(90mm)
FP651
Fig. 1 NVSTR36 Series specification and framing dimensions.
NVCVR36 Series Gas Appliance, Cove
FP651
NVSTR36
3/30/98
Model
���" (16mm) Framing Recess
6" DIA.
���" Recessed
(16mm) Nailing
Flange
Rough
Opening
Height
����"
(191mm)
40���"
(1029mm)
36"
(914mm)
�����" Rough
(578mm) Opening
Depth
36"
(914mm)
21"
(533mm)
Gas Line
Access
Outside
Air
8"
(203mm)
����"
(165mm)
11"
(279mm)
����"
(191mm)
40���"
(1029mm)
3���"
(90mm)
12"
(305mm)
3���"
(79mm)
Electrical
Access
FP652
Fig. 2 NVCVR36 Series specification and framing dimensions.
4
FP652
NVCVR36
3/30/98
7412958
NVSTR/ NVCVR Series
Clearance to Combustibles
Appliances
Top .......................................................... 0” (0 mm)
Bottom ..................................................... 0” (0 mm)
Side ......................................................... 0” (0 mm)
Back ........................................................ 0” (0 mm)
Perpendicular Sidewall ....................... 6” (152 mm)
Top of unit to ceiling .......................... 36” (914 mm)
Front of unit to combustibles ............. 36” (914 mm)
Venting
J
Black Surround
Face
I
H
G
Mantel
Leg
B-Vent ................................................... 1” (25 mm)
F
CFM164a
Mantels
The height that a combustible mantel is fitted above the
fireplace is dependent on the depth of the mantel. This
also applies to the distance between the mantel leg (if
fitted) and the fireplace.
M
N
O
CFM164a
Side
of Combustion Chamber
Mantel Leg Chart
06/22/01 sta
K
L
For the correct mounting height and widths refer to
Figures 3a and 3b.
Noncombustible mantels and legs may be installed at
any height and width around the appliance.
When using paint or lacquer to finish the
mantel, such paint or lacquer must be heat
resistant to prevent discoloration.
CFM170
V
W
X
Ref.
Y
F
G
H
I
J
Z
A
B
C
D
E
CFM146a
V
W
X
Y
Z
14"
12"
10"
8"
1¹⁄₂"
CFM146
Ref.
DV Mantel Chart
7/5/01 sta
rev. 10/1-02 rjs
(356 mm)
(305 mm)
(254 mm)
(203 mm)
(38 mm)
A
B
C
D
E
Mantel From Top
of Comb. Chamber
25"
23"
21"
19"
15"
(635 mm)
(584 mm)
(533 mm)
(483 mm)
(381 mm)
Fig. 3a Combustible mantel minimum installation.
7412958
View
(356 mm)
(305 mm)
(254 mm)
(203 mm)
(38 mm)
K
L
M
N
O
14"
12"
10"
8"
1¹⁄₂"
(356 mm)
(305 mm)
(254 mm)
(203 mm)
(38 mm)
Hearth Extension
Top of Combustion
Chamber
Ref.
14"
12"
10"
8"
1¹⁄₂"
Mantel From Top
of Comb. Chamber
Fig. 3b Combustible mantel leg minimum installation.
Fireplace
Mantel
Shelf Depth
MantelCFM170
DV Builder Front
Shelf Depth
Ref.
A hearth extension in front of appliance is recommended, but not required.
Insulating for Cold Climates
When an appliance is installed in a chase or an outside
wall, the enclosure should be insulated like any other
wall of the home. Insulation should be installed under
the appliance and on the inside of the exterior walls.
In a chase, it is a good idea to install a firestop at the
first ceiling level above the appliance. Also, install insulation on the side walls. Insulation may then be placed
above the ceiling to assure the space around the appliance is protected. Refer to Page 7, Figure 5.
5
NVSTR/ NVCVR Series
Be sure to always maintain the proper one
(1) inch distance to combustibles around
B-vent pipe sections.
NOTE: Insulating for cold climates is strictly a recommendation and not a requirement.
Framing and Finishing
When finishing the appliance, never obstruct or modify
the air inlet/ outlet grilles in any manner.
Finish the wall with the material of your choice. Refer to
Figures 3a and 3b for specific clearances when installing a combustible mantel or other combustible projection.
Gas Specifications
The appliance should only be mounted on the following
surfaces:
• A flat combustible (burnable) surface.
• A raised wooden platform.
• A concrete block or other solid object placed
beneath each of the four corners of the appliance.
To mount the appliance:
1. Choose unit location.
2. Eight (8) nailing flanges are supplied with the
NVSTR fireplace (found on the fireplace hearth).
Four (4) nailing flanges are supplied with the NVCVR
fireplace. To level the box and secure it firmly in
place, remove the nailing flanges from the hearth
and install at the sides of the fireplace as shown in
Figure 4.
Nail top
standoffs
Nail eight (8)
side-nailing
flanges
Model
NVSTR36RN
NVSTR36RP
NVSTR36EN
NVSTR36EP
NVCVR36RN
NVCVR36RP
NVCVR36EN
NVCVR36EP
Fuel
Natural
LP
Natural
LP
Natural
LP
Natural
LP
Gas Control
Millivolt Hi/Lo
Millivolt Hi/Lo
Electronic
Electronic
Millivolt Hi/Lo
Millivolt Hi/Lo
Electronic
Electronic
Max.
Input
41,000
41,000
41,000
41,000
41,000
41,000
41,000
41,000
Min.
Input
29,000
31,500
29,000
31,500
29,000
31,500
29,000
31,500
Gas Inlet & Manifold Pressures
NATURAL
Minimum Inlet Pressure
Maximum Inlet Pressure
Manifold Pressure
5.5" w.c.
14.0" w.c.
3.5" w.c.
LP
11.0" w.c.
14.0" w.c.
10.0" w.c.
NVSTR36 / NVCVR36
Certified To
ANSI Z21.50b–2002/ CSA 2.22b–2002
Vented Gas Fireplace
Units: F34AR6, F34BR6, F34HR6, F34AR9, F34HR9
NVSTR36
High Elevations
Nail top
standoffs
Nail four (4)
side-nailing
flanges
NVCVR36
FP658
Fig. 4 Adjustable drywall strip
(nailing flange).
FP658
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/ or local codes
having jurisdiction.
In Canada, please consult provincial and/ or local
authorities having jurisdiction for installations at
elevations above 4,500 feet (1,370 m).
3/30/98
NVSTR/NVCVR36
Finishing
rev. 8-15-02
rjs
All joints between finished wall and appliance surround (top and sides) may be
sealed only with noncombustible material.
Only noncombustible material can be applied as facing to the appliance surround
(black painted face).
6
7412958
NVSTR/ NVCVR Series
Parts Identification and Chase Installation
(Insulation methods shown are optional for cold climate, not a requirement for unit operation.)
Termination Cap
Storm Collar
Pan Flashing
NVSTR
Batt Insulation
(cut out around
firestop)
Draftstop
Firestop
Ceiling Level
Header*
Standoff
Surround
Nailing Flange
Screen
Electrical
Access
Grate
Firebox
Valve Cover
Plate
Outside Air
Cover Plate
FF656
NVSTR (from FP528)
4/23/98
NVCVR
FP656
Termination Cap
Storm Collar
Pan Flashing
Batt Insulation
(cut out around
firestop)
Draftstop
Firestop
Ceiling Level
Header*
Standoff
Surround
Nailing Flange
Electrical Access
(on side)
Outside Air Cover Plate
Screen
Grate
Firebox
Valve Cover Plate
* Do not install header until unit is in place.
FP657
Fig. 5 Parts identification and system installation.
7412958
FF657
NVSTR (from FP528)
4/23/98
7
NVSTR/ NVCVR Series
Gas Line Installation
If gas piping is not yet completed from the source to the
appliance location, install the required pipe. To ensure
use of proper pipe size, consult the local plumbing
code.
The gas pipeline can be brought in through the righthand side (facing the control side) of the appliance.
A knockout is provided to allow for the gas pipe installation and testing of any gas connection.
2. Attach wire to switch and install switch into receptacle box. Attach cover plate to switch.
3. Connect wiring to gas valve. Refer to Figure 7 or 8
and follow the appropriate diagram.
CAUTION: Do not wire millivolt remote
wall switch for gas applicnce to 120V
power supply. For lighting instructions, refer
to Page 13 or 14.
R Models
NOTE:The gas line connection can be made with
properly tinned 3/8" copper tubing, 1/2" rigid pipe or an
approved flex connector, then reduced to 3/8" to the
appliance. Because some municipalities have some
additional local codes, it is always best to consult your
local authority.
Pilot
U.S.A.: Consult the current National Fuel Gas Code,
ANSI Z223.1/NFPA 54.
Thermodisk
CANADA: CSA–B149.1 Installation Code.
Always check for gas leaks with a mild
soap and water solution. Do not use an
open flame for leak testing.
The gas control is equipped with a captured screw type
pressure test point, therefore it is not necessary to provide a 1/8" test point up stream of the control.
NOTE:If flex connector is used, it must be kept inside of
the appliance. (Fig. 6)
Valve
HV105
Fig. 7 Remote switch wiring for R-Models.
Honeywell
Ignition
1/2" Gas Supply
HV105 WHITE
Generic Gas Valve
9/22/99 djt
PILOT
1/2" x 3/8" Shut-off Valve
HONEYWELL S8600 B IGNITION MODULE
MV
MVPV
PV
3/8" Nipple
3/8" Union
24V
GND
24V
SPARK
SENSE
WHITE
WHITE
BLACK
BLACK
WHITE
BLACK
WHITE
E
3/8"
Nipple
GND
(BURNER)
BLACK
When using copper or flex connector use only approved
fittings. Always provide a union so the gas line can be
easily disconnected for burner or fan servicing. See gas
specification for pressure details and ratings.
On/Off
Switch
A
LO
HI
LO
FP598
HI
T
Fig. 6 Typical gas supply installation.
GF598
1. Thread wire through
the electrical knockout located
nvb GAS
SUPPLY
on side of unit. Run
the other
endINSTALL
to a conveniently
12/4/97
located wall receptacle box. Ensure the wire is protected; do not cut wire or insulation on metal edges.
Thermodisk
PILO
NOVA SIT 822 VALVE
Remote Wall Switch
BLACK
24 VAC HOT
120 VAC RTN
1 5
WHITE
3 4
BLACK
120 VAC HOT
GREEN
BLACK
BLACK
WHITE
WHITE
ON-OFF
SWITCH
24 VAC RTN
40VA
TRANSFORMER
FP670
Fig. 8 Remote switch wiring for E-Models.
8
7412958
FP670
NOVA SIT 822 VALVE WIRING DGRM.
(w/ Honeywell S8600 B Ignition Module)
4/30/98
NVSTR/ NVCVR Series
EB-1 Electrical Box
The fireplace, when installed, must be
electrically connected and grounded in
accordance with local codes or, in the absence of local codes, with the current CSA
C22.1 Canadian Electrical Code.
Install the Venting System,
Flashing, and Termination
See venting installation instructions provided by the BVent manufacturer.
Refer to Page 4, Figure 1 to locate chimney centerline
dimension from a combustible back wall.
For USA installations, follow local codes
and the National Electrical Code, ANSI/
NFPA No. 70.
• Minimum vertical chimney height — 12 feet (3.65m).
It is strongly suggested that the wiring of
the EB-1 electrical junction box be carried
out by a licensed electrician.
• Minimum height with two 90° elbows — 16 feet
(4.06m)
Ensure that the power to the supply line
has been disconnected before commencing this procedure.
Once the fireplace is secured, complete wiring the fan
kit. Remove knockout in the center of the back of the
EB1 and install listed cable clamps. Feed electrical
wire through cable clamp leaving approximately six (6)
inches of wire exposed through the EB1. Secure cable
clamp to the wire.
Attach white wire from power source to one (1) wire of
receptacle and secure with a nut. Attach black wire from
power source to the other wire of the receptacle and
secure with a nut. Be sure nuts are tightened securely.
Secure the EB1 assembly to the inside of the electrical
box coverplate using two (2) screws. Attach the cover
to the face of the EB1 while being careful to position
excess wire completely within the EB1. Attach the coverplate to the fireplace. (Fig. 9)
Inside
• Maximum vertical height — 40 feet (12m).
• Elbow requirements allow a maximum of two
90 degree elbows or four 45 degree elbows
per installation. (Two 45 degree elbows =
One 90 degree elbow.) See venting chart for
proper elbow offset runs. Use Figure 11 for all
NVCVR installations and NVSTR installations when
not installing 36GSKBB Single Panel Glass Door.
Use Figure 12 for NVSTR installations when using
36GSKBB Single Panel Glass door.
For firestop positioning, refer to Figure 10. Only one
(1) firestop required per frame. NOTE: A firestop is not
required at the roof.
Attic Installation
Firestop position when area above ceiling is an attic.
Nails (4)
Firestop Spacer
Joist
Electrical Box
Ceiling Installation
Firestop position when area above ceiling is NOT an attic.
Front O
f Unit
Outside
NOTE: Firestop/draftstop
appearances may vary.
Only one (1) firestop is
required per frame.
t
Fron
nit
Of U
FP384
FP580
Fig. 9 Junction box (EB-1) hook-up.
7412958
Fig. 10 Firestop/ draftstop
positions.
FP384
FIRESTOP
11/21/96
rev 1-10-03
rjs
9
FP580
INSTA VENT FREE
EB1 JUNCTION BOX
11/18/97
NVSTR/ NVCVR Series
Venting Runs
Horizontal Run (in feet)
1 2 3 4 5 6 78 9 10
34
40
38
36
A
B
Horizontal Run (in feet)
4
6
8
10 12 14 16 18 20
A
B
34
Vertical Run (in feet)
32
30
28
26
24
22
20
18
32
Vertical Run (in feet)
40
38
36
2
30
28
26
24
22
20
18
16
16
14
14
12
= Acceptable venting configuration
= Unacceptable venting configuration
A: Vertical installations up to 40 feet (12.2 m) in
height. Up to a 6 ft. (1.8 m) horizontal vent run
can be installed within the vent system using
a maximum of two 90-degree elbows or four
45-degree elbows.
B: Vertical installations up to 40 feet (12.2 m) in
height. Up to a 10 ft. (3.05 m) horizontal vent run
can be installed within the vent system using
a maximum of two 45-degree elbows.
FP567
FP567
Fig. 11 Venting
configurations.
NVBR/NVBC VENTING RUNS
11/12/97
rev. 8-21-02
rjs
12
10
8
= Acceptable venting configuration
= Unacceptable venting configuration
A: Vertical installations up to 40 feet (12.2 m) in
height. Up to a 16 ft. (4.06 m) horizontal vent
run can be installed within the vent system
using a maximum of two 90-degree elbows or
four 45-degree elbows.
B: Vertical installations up to 40 feet (12.2 m) in
height. Up to a 20 ft. (6.1 m) horizontal vent
run can be installed within the vent system
using a maximum of two 45-degree elbows.
FP567a
Fig. 12 Venting configurations when installing 36GSKBB.
10
7412958
FP567a
Venting
8/17/99
rev. 8-21
NVSTR/ NVCVR Series
Operating Instructions
Glass Information
Only glass approved for use in Majestic
Fireplaces products may be used for replacement.
• Glass doors are optional. The appliance may be
•
•
•
•
•
operated safely without glass doors.
The use of any non-approved replacement glass will
void all product warranties.
Bi-fold glass doors MUST BE completely open or
closed while the appliance is in operation.
Care must be taken to avoid breakage of the glass.
Under no circumstances should this appliance be
operated with broken glass. Replacement of the
glass as supplied by the manufacturer should be
completed by a licensed qualified service person.
Replacement glass is available through your
Majestic Fireplaces dealer and should only be
installed by a licensed qualified service person.
Log Installation
Glass Cleaning
It will be necessary to clean the glass periodically.
During start-up, condensation, which is normal, forms
on the inside of the glass and causes lint, dust and
other airborne particles to cling to the glass surface.
Also, initial paint curing may deposit a slight film on
the glass. It is therefore recommended that the glass
be cleaned two or three times with a non-ammonia
household cleaner and warm water (we recommend
gas fireplace glass cleaner). After that the glass should
be cleaned two or three times during each heating
season depending on the circumstances present.
Clean glass after first two weeks of
operation.
Lava Rock
The lava rock provided with this fireplace must be
placed on the firebox base on either side of the burner
assembly. Do not place lava rock in combustion pan.
Under no circumstances should lava rock
be placed on any part of the burner assem1. Open glass door (if installed).
bly.
2. Remove logs from the packaging.
As with all plastic
items, these logs
are not toys and
should be kept
away from children
and infants.
3. Place rear log on back
bracket. Ensure that log is
firmly positioned and there
is no side-to-side movement.
LG312
4. Place the front log on the
front bracket. Ensure that
Fig. 13 NVSTR36/ NVCVR36 log placement.
the log is firmly positioned
First Firing
and there is no side to side movement.
5. Place the four top logs onto the front and rear logs
Upon completing the gas line connection, a small
as shown in Figure 13. Ensure that the logs are seamount of air will be trapped in the line. When first lightcure on the tabs located on the front and rear logs.
ing the unit with pilot light, it will take a few minutes to
purge the trapped air.
Ember Material Placement
Once purging is complete, the pilot and burner will light
and operate as indicated in the instruction manual.
Separate the ember material into small pieces—roughly
Subsequent lightings of the appliance will not require
1/2" (13 mm) diameter—and place on the bracket over
purging.
the lower burner tubes. Do not pack down ember mateWhen lit for the first time, the appliance will emit a slight
rial; leave in loose, fluffy condition for the most realistic
odor for an hour or two. This is due to paint and lubriember effect. (Fig. 14)
cants used in the manufacturing process.
After each lighting, vapor may condense and fog the
glass; this moisture disappears in a few minutes of
burning.
7412958
11
20005477_log_placement
NVSTR_CVR36
9-23-02
rjs
NVSTR/ NVCVR Series
Log, Left Front,
Right Rear Cross
20005441
Log, Right Front,
Left Rear Cross Log
20005442
Log, Left Front
20005445
Log, Right Front
20005446
Log, End
3079168
NVCVR
Only
Log, Right Rear
20005444
Log, Left Rear
20005443
Log,
Right Front, Left
Rear Cross Log
20005442
(Valve Side)
Log, Left Front,
Right Rear Cross
20005441
LG313
Fig. 14 Ember placement.
�����
Flame Adjustment
������������������
For units equipped with Hi/Lo����
valves, flame adjustment
is accomplished by rotating the Hi/Lo adjustment knob
located near the center of the gas control.
Turn
counterclockwise
to increase
flame height.
HI
LO
Turn clockwise
to lower
flame height
LG314
Fig. 15 Flame adjustment knob for SIT820 valve.
Flame
FP390
FLAME ADJUSTMENT KNOB
Characteristics
11/21/96
It is important to periodically perform a visual check of
the pilot and the burner flames. Compare them to the
illustrations below (Figs. 16, 17). If any of the flames
appear abnormal call a service person.
ELECTRONIC
IGNITION
NOVA SIT PILOT
Fig. 17 Approximate flame heights.
20005477_flameheight
Inspecting
the Venting System
NVSTR_CVR36
The appliance venting system was designed and con9-23-02
rjs
structed to develop a positive flow adequate to remove
flue gases to the outside atmosphere.
Any foreign objects in the venting system, except those
designed specifically for the venting system, may cause
spillage of flue gases (i.e.: carbon monoxide) into the
room.
To inspect the venting system, make sure the main gas
valve is off. Remove the glass panel. Using a flashlight,
check the combustion dome and behind the top grille.
Clean if necessary.
3/8"-1/2"
FP581
FP581 PILOTS/ ... 2
Fig. 16 Proper pilot flame height.
12/4/97
rev. 8-16-02 rjs
12
7412958
NVSTR/ NVCVR Series
Lighting and Operating Instructions
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manually. When lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace.
• Do not touch any electric switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the Fire Department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn clockwise
to "OFF".
OFF
ON
OFF
T
LO
3/8" - 1/2"
OFF
3 4 5
Euro SIT
PI
ON
1 2
P
OFF ilot
PILOT
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depressing the piezo spark igniter until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
SIT NOVA
Honeywell
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow "B" in the safety inforFP1067
mation above. If you
do not smell gas, go to the
lighting instruction
next step.
knobs
7. Remove glass door
before
3/9/01
djt lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to "PILOT".
• If after several tries, the pilot will not stay lit, turn
the gas control knob to "OFF" and call your service technician or gas supplier.
FP1068
11. Replace glass door.
Lighting instructions
12. Turn gas control knob to Pilots
“ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas to Heater
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting.
2. Turn off all electric power to the fireplace if
service is to be performed.
7412958
3. Open louvre assembly bottom.
4. Push in gas control knob slightly and turn
clockwise
to "OFF". Do not force.
5. Close control access panel.
13
NVSTR/ NVCVR Series
Lighting and Operating Instructions
For Fireplaces equipped with SIT822 Gas Valve (EN or EP)
Warning:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury and loss of life.
FOR YOUR SAFETY READ THE FOLLOWING WARNINGS
BEFORE LIGHTING THE APPLIANCE
A. This fireplace is equipped with an ignition device
which automatically lights the pilot. DO NOT try to
light the pilot by hand.
B. BEFORE OPERATING, smell all around the
appliance area for gas. Be sure to smell next to
the floor because some gas is heavier than the air
and will settle on the floor.
What to do if you smell gas
•
Do not try to light any appliance
•
Do not operate any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a
neighbor’s phone.
Follow the gas suppliers instructions.
•
If you cannot contact your gas supplier call
the Fire Department
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in
or turn by hand do not try to repair it, call a qualified
service technician. Force or attempting repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and replace any part of the
control system and any gas control that has been
under water.
Lighting Instructions
1. STOP! Read the safety information above before
continuing.
2. Turn off all electrical power to the appliance.
3. This appliance is equipped with an ignition device
which automatically lights the pilot. DO NOT try to
light the pilot by hand.
4. Access the gas control by lowering the lower
access door (louvre assembly).
LO
HI
5. Turn the remote switch, if used, OFF. Turn the
wireless remote, if used, OFF.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas STOP. Follow instructions B in the safety
warnings above. If you do not smell gas go onto the
next step.
7. Close the access door.
8. Turn ON all electrical power to the appliance.
9. Turn remote switch or wireless remote to “ON”.
10. If the appliance will not operate, follow the
instructions TURNING OFF THE GAS TO THE
APPLIANCE and call your service technician or
gas supplier.
Turning Off the Gas to the Appliance
1/2" Gas Supply
1. Turn the remote switch to the “OFF” position.
2. Turn OFF all electrical power to the fireplace if
service is required.
1/2" x 3/8" Shut-off Valve
3/8" Nipple
3/8" Union
3 Open the lower access panel.
3/8"
Nipple
4. Turn the shut-off valve on the flexible gas line to the
“OFF” position.
Valve in the "ON" position
14
7412958
NVSTR/ NVCVR Series
Troubleshooting
Nova SIT 820 Standing Pilot
START
Gas Supply On
CHECK
NO
YES
Pilot Lights with
Piezo Ignitor
NO
• Supply Line Hooked up
• Shutoff Valve Open
• Lockout has engaged. Wait 60
seconds and try again.
• Piezo not tight enough for good
ground.
• For spark at electrode while
depressing Piezo (Red Button)
1/8" gap to pilot hood needed.
• All wiring connections
• Replace Piezo Ignitor
• Thermodisk
YES
Pilot Stays Lit
NO
YES
Pilot Lights Main
Burner
NO
• For Air in the lines
• Thermopile needs a minimum
325mV. Adjust pilot flame height.
• All wiring connections
• Replace Thermopile
• Thermocouple needs a minimum
of 14mV.
• Defective valve. Turn to pilot,
meter should read greater than
100mV.
• Thermodisk
• Wall switch is not turned on.
Watch for grounded wires!
• Thermopile needs a minimum
325mV
• Plugged burner orifice
YES
System OK
FP396
NVC-standing pilot troubleshooting
5/6/98
7412958
FP396
15
NVSTR/ NVCVR Series
Troubleshooting
NOVA SIT 822 w/ Honeywell S8600 B Electronic Ignition
Remove glass panel before servicing.
START
• Turn gas supply off
• Turn ON/OFF Switch
to call for heat.
CHECK : • Line Voltage (120VAC)
NO
• Low Voltage Transformer
(19.5 minimum VAC)
• ON/OFF Switch
• Wiring connections
• Thermodisk
Power to module
(24V nominal)
Unplug Ignition Lead
and check spark
at module
(24VAC nominal)
YES
Spark across
Ignitor Sensor gap
NO
NO
• Replace Module
Spark OK?
YES
YES
• Check ignition cable, ground wiring, Ceramic Insulator and gap. Correct as necessary
• Check boot of ignition cable for signs of melting or buckling. Take protective
actions to shield cable and boot from excessive temperatures.
• Turn gas on
NO
Pilot burner lights?
YES
Spark stops when pilot
is lit?
•
•
•
•
•
•
•
YES
Troubleshooting
Ends
Check continuity of ignition cable and ground wire.
Clean flame rod.
Check electrical connections beween flame rod and module.
Check for cracked ceramic flame rod insulator.
Check that pilot flame covers flame rod and is steady blue.
Adjust pilot flame.
If problem persists, replace module.
NO
• Check for 24VAC across MV-MV/PV terminals. If no voltage, replace module.
• Check electrical connections between module and gas control. If okay, replace gas
control or gas control operator.
NO
NOTE: If S8600B goes into lockout, reset system.
YES
System runs until
ON/OFF switch is in
"OFF" position
NOTE: If S8600B goes into lockout, reset system.
NO
YES
Main Burner lights?
• Check that all manual gas valves are open, supply tubing and pressures are good,
and pilot burner orifice is not blocked.
• Check electrical connections between module and pilot operator on gas control.
• Check for 24VAC across PV-MV/PV terminals on module. If voltage is okay, replace
gas control. If not, replace module.
• Check for continuity of igniton cable and ground wire. NOTE: If ground is poor or
erratic, shutdowns may occur occasionally even though operation is normal
at time of checkout.
• Check that the pilot flame covers flame rod and is steady and blue.
• If checks are okay, replace module.
FP649
FP649 Honeywell S8600B T-shoot Guide
16
5/5/98
7412958
NVSTR/ NVCVR Series
Maintenance
Keep the control compartment, logs and burner area
surrounding the logs clean by vacuuming or brushing at
least twice a year. THE LOGS CAN GET VERY HOT
— HANDLE ONLY WHEN COOL.
Always turn off gas to the pilot before cleaning. For
relighting, refer to lighting instructions located on the
front cover plate.
Never obstruct the flow of combustion and ventilation
air. Keep the front of the appliance clear of all obstacles
and materials.
Leave at least 36" clearance from front of appliance to
combustibles.
Cleaning the Standing
Pilot Control System
The burner and control system consists of:
•
•
•
•
•
main burner
gas orifice
pilot burner
thermopile
combination millivolt gas valve
Cleaning Automatic Direct
Electronic Ignition System
The Electronic Ignition burner/ control system consists
of:
•
•
•
•
main burner
gas orifice
hot surface pilot burner
24VAC valve with transformer
Taking care of the Electronic Ignition units is almost
identical to taking care of the Standing Pilot models.
(See the Maintenance section on page 16.)
The hot surface ignitor is the only component which
requires EXTREMELY DELICATE HANDLING. The
ignitor is made of silicone carbide which is a very brittle
material.
Do not touch the heating part of the ignitor
with your fingers.
Most of these components may require only an occasional checkup and cleaning and some may require adjustment. If repair is necessary, it should be performed
by a qualified technician.
In order to properly clean the burner and pilot assembly, turn off the gas to the unit, open the glass door
(if used), remove logs exposing the burner and pilot
assembly. Clean all foreign materials from the top of the
burner. Check to make sure that burner parts are clean.
Visually inspect pilot. Brush or blow away any dust or
lint accumulation If pilot orifice is plugged, disassembly
may be required to remove any foreign material from
the orifice or tubing.
To obtain proper operation, it is imperative that the pilot
and burner's flame characteristics are steady, not lifting
or floating.
Typically, the top 3/8" or 1/2" of the thermopile should
be engulfed in the pilot flame. (Page 12, Fig. 16)
To adjust pilot burner, adjust pilot screw marked "pilot"
for proper size:
1. Remove pilot adjustment cap.
2. Adjust pilot screw to provide properly sized flame.
3. Replace pilot adjustment cap.
The air shutter is set at factory; no adjustment should
be necessary.
7412958
17
NVSTR/ NVCVR Series
29
13
14
13
35a,b
14
2
34
17a
16a
3a,b
30
21
15
19
18
20
31
17
23
22
Nova SIT 822 Valve
Nova SIT 820 Valve
1 NVSTR/ NVCVR36 Logs
12a/b
�
������
�
� � ��� �� ������
������
�����
�����
�� �����
� � ��� ����
�
��� �
�
�
��� �
�
��
8
��
5a/b
�����
��
1c
��
�
������� ���
��
� ��� �
������ ��� � �
���
���
���
24a/b
�
��� ��
��
TH
�
������� ����
��
��
�
� � � ��
�
TP
1b
�
THTP
1a
�
16
25a/b
1d
28
10
1e
26
11
9
1f
1g
7
6
4a/b
MV
MVPV
PV
GND
(BURNER)
24V
24V
SENSE
SPARK
27
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
NVSTR/CVR (F34)
Ref.
1.
1a.
1b.
1c.
1d.
1e.
1f.
1g.
2.
18
Description
Complete Log Set
Log, Lt Front/ Rt Rear Cross
Log, Rt Front/ Lt Rear Cross
Log, Left Rear
Log, Right Rear
Log, Left Front
Log, Right Front
Log, End (used for NVCVR only)
Burner - Natural/ LP
958_NVSTR_CVR_parts
FP663 NVSTR-NVCVR36
(from FP397 & FP578)
replacement parts 4/30/98
rev. 9-23-02 (new name) rjs
Part Number
20005477
20005441
20005442
20005443
20005444
20005445
20005446
3079168
20005351
7412958
NVSTR/ NVCVR Series
NVSTR/ CVR (F34) (continued)
Ref.
Description
3a.
3b.
4a.
4b.
5a.
5b.
6.
7.
8.
9.
10.
11.
12a.
12b.
13.
Burner Orifice - Natural
Burner Orifice - LP
Orifice, Pilot, #62 Top Conv.
Orifice, Pilot, #35 Top Conv.
Pilot Assembly 3-way N/DV RN Top Conv.
Pilot Assembly 3-way N/DV RP Top Conv.
Piezo Ignitor
Cable Ignitor
Electrode Ignitor Nova
Pilot Tubing
Thermocouple, 24”
Thermopile, 24”
Valve Nova, NG SIT 0.820.652
Valve Nova, LP SIT 0.820.651
Side Brick
14.
15.
16.
16a.
17.
17a.
18.
19.
20.
Corner Brick
Ceramic Panel, End
Ceramic Panel, Left
Ceramic Panel, Left
Ceramic Panel, Right
Ceramic Panel, Right
Ceramic Panel
Ceramic Panel
Door Track, Black
Door Track, Brass
Remote Switch Kit
Lava Rock Package
Bag of Embers
Valve Nova, EN SIT 0.822.632, 24 V/ 60 Hz
Valve Nova, EP SIT 0.822.631, 24 V/ 60 Hz
Pilot Assembly 3-way N/DV RN Top Conv.
Pilot Assembly 3-way N/DV RP Top Conv.
Transformer
Ignition Device/ Honeywell
Sensing Electrode
End Panel
Thermodisk (F33 Only)
O.S.A. Assy. (F32 & F33 Only)
Conversion Kit, Natural
Conversion Kit, LP
Grate
Air Shutter, Natural
Air Shutter, LP
21.
22.
23.
24a.
24b.
25a.
25b.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35a.
35b.
7412958
Part Number
20005480
20005481
10002268
10002269
10002264
10002265
52464
53194
52465
7549333
53373
51827
7529141
7529142
3079147
NVSTR
NVCVR
3079148
3079148
—
3080123
—
3080122
3079139
—
—
3080121
3079138
—
—
3080125
—
3080124
3061102
3067102
53875
55255
7060109
57884
57883
10002387
10002388
7522409
20000005
57885
3080145
20001558
20003212
20005458
20005457
10002323
20000129
20000680
19
NVSTR/ NVCVR Series
Contact CFM Corporation for questions concerning
prices and policies covering replacement parts. Parts
may be ordered through your CFM Corporation distributor or dealer.
You will need the following information when ordering
replacement parts:
1. The appliance model number.
2. The serial number.
3. A description of the part.
Should you need additional information beyond what
your dealer can furnish, contact:
Model and serial numbers are listed on the rating plate (located on right side of combustion
chamber).
Record your model and serial numbers here for
future reference:
Model #
____________________________
Serial #
____________________________
CFM Corporation
410 Admiral Blvd.
Mississauga, Ontario
Canada L5T 2N6
Attn: Manager of Customer Service
20
7412958
NVSTR/ NVCVR Series
Accessories
Glass Doors
Bi-fold and single panel glass doors are available to
enhance the viewing of the fireplace.
Unit
NVSTR/CVR
NVSTR/CVR
NVSTR/CVR
NVSTR/CVR
NVSTR/CVR
NVCVR
NVCVR
NVCVR
Models
Description
36GSKBB Brushed Brass Solid Glass
Panel
36GDKBB Brushed Brass Bi-fold
36GDKBK Black Bi-fold
36GDKDP Polished Brass Bi-fold
36GDKS Pewter Bi-fold
36EPKBK Black End Panel Extrusion Kit
36EPKDP Polished Brass End Panel
Extrusion Kit
36EPKS Pewter End Panel Extrusion Kit
Outside Air Kit
The Model AK-MST Outside Air Kit is designed to bring
additional combustion air directly from the outside to the
fireplace. Refer to installation instructions provided with
the Outside Air Kit.
Tab
Thermal Vent Damper
Screws
FP577
Fig. 18 Attach the thermal vent damper.
Remote
Controls
FP577
NVB—TVD6/7
Optional remote control
units are available to control
11/17/97
different functions of the appliance.
Model
RC1
RC2
Function/s Controlled
“ON/OFF”
“ON/OFF” and Temperature
Thermal Vent Damper
Installing the TVD6/7 Thermal Vent Damper reduces
cold air infiltration when fireplace is not in use by opening and closing automatically.
Attach the thermal vent damper to the combustion
dome with 2 screws. Be sure the tab points down. (Fig.
18)
Start the appliance and operate it for approximately 5
minutes. Turn the unit off and check if the vent damper
is in the open position (blades down from the horizontal
position). If the damper has not opened, check installation.
NOTE: Not for use in Canada.
7412958
21
NVSTR/ NVCVR Series
22
7412958
LIMITED LIFETIME WARRANTY
NVSTR/ NVCVR Series
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic or Northern Flame brand gas
fireplaces equipped with an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
CFM Corporation (hereinafter referred to collectively as the Company)
warrants that your new Vermont Castings or Majestic Gas Fireplace/
Stove is free from manufacturing and material defects for a period of
one year from the date of purchase, subject to the following conditions
and limitations.
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted for
life against through wall perforation. All appliances equipped with an
Insta-Flame Ceramic Burner have limited lifetime coverage on the
ceramic burner plaque. Warrantees are made to the original owner
subject to proof of purchase and the conditions and limitations listed
on this Warranty Document
•
•
•
•
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
Note: On porcelain enamel finished external parts and accessories The
Company offers no Warranty on chipping of enamel surfaces. Inspect
all product prior to accepting it for any damage to the enamel.
The salt air environment of coastal areas or a high humidity
environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
Dye lot variations with replacement parts and/or accessories can occur
and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only. Brass cleaners cannot be used. Mortar mix
and masonry cleaners may corrode the brass finish. The Company will not
be responsible for, nor will it warrant any brass parts which are damaged
by external chemicals or down draft conditions.
GAS VALVES: Gas valves are covered for a period of one year
•
•
•
•
•
•
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one year.
All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Corporation company supplied accessories are covered for a period of
one year.
CONDITIONS AND LIMITATIONS
•
•
•
•
This new Vermont Castings or Majestic product must be installed by
a competent, authorized, service contractor. A licensed technician, as
prescribed by the local jurisdiction must perform any installation/service
work. It must be installed and operated at all times in accordance with
the Installation and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the product shall
nullify this warranty.
This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
The customer must pay for any Authorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
If upon inspection, the damage is found to be the fault of the
manufacturer, repairs will be authorized at no charge to the customer
parts and/or labor.
7412958
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after
said defect is confirmed by the Company’s inspection.
The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of the
defective part(s)
Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall
the Company assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or consequential
damages except as provided by law.
SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of
this Vermont Castings, Majestic product
The warranties as outlined within this document do not apply to chimney
components or other non Vermont Castings, Majestic accessories used
in conjunction with the installation of this product..
Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer
from whom you purchased your fireplace/stove (do not operate the
appliance as this might negate the ability to process the claim with the
carrier).
The Company will not be responsible for:
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolonged periods of
dampness or condensation
c) Any damages to the fireplace, combustion chamber, heat
exchanger or other components due to water, or weather damage,
which is the result of but not limited to, improper chimney/venting
installation.
d) Any alteration, willful abuse, accident, or misuse of the product
has occurred.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your warranty, your
sales receipt, and the model/ serial number of your CFM Corporation
appliance.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.
23
CFM Corporation
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6
800-668-5323 • www.cfmcorp.com