Yamaha WaveRunner XL1200Ltd Service manual

WaveRunner
XL1200Ltd
SERVICE
MANUAL
LIT186160198
LIT-18616-01-98
F0D-28197-Z9-11
E
NOTICE
This manual has been prepared by the Yamaha Motor Company Ltd. primarily for use by
Yamaha dealers and their trained mechanics when performing maintenance procedures and
repairs to Yamaha equipment. It has been written to suit the needs of persons who have a
basic understanding of the mechanical and electrical concepts and procedures inherent in the
work, for without such knowledge attempted repairs or service to the equipment could render
it unsafe or unfit for use.
Because the Yamaha Motor Company, Ltd. has a policy of continuously improving its products, models may differ in detail from the descriptions and illustrations given in this publication. Use only the latest edition of this manual. Authorized Yamaha dealers are notified
periodically of modifications and significant changes in specifications and procedures, and
these are incorporated in successive editions of this manual.
A10001-0*
WaveRunner XL1200Ltd
SERVICE MANUAL
1999 Yamaha Motor Co., Ltd.
1st Edition, March 1999
All rights reserved.
No part of this publication may be
reproduced or transmitted in any form or by
any means including photocopying and
recording without the written permission of
the copyright holder.
Such written permission must also be
obtained before any part of this publication
is stored in a retrieval system of any nature.
Printed in USA
LIT-18616-01-98
E
HOW TO USE THIS MANUAL
MANUAL FORMAT
All of the procedures in this manual are organized in a sequential, step-by-step format. The
information has been compiled to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and
inspection operations.
In this revised format, the condition of a faulty component will precede an arrow symbol and
the course of action required will follow the symbol, e.g.,
● Bearings
Pitting/scratches → Replace.
To assist you in finding your way through this manual, the section title and major heading is
given at the top of every page.
ILLUSTRATIONS
The illustrations within this service manual represent all of the designated models.
CROSS REFERENCES
The cross references have been kept to a minimum. Cross references will direct you to the
appropriate section or chapter.
E
IMPORTANT INFORMATION
In this Service Manual particularly important information is distinguished in the following
ways.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
WARNING
Failure to follow WARNING instructions could result in severe injury or death to the machine
operator, a bystander, or a person inspecting or repairing the water vehicle.
CAUTION:
A CAUTION indicates special precautions that must be taken to avoid damage to the water
vehicle.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
IMPORTANT:
This part has been subjected to change of specification during production.
E
HOW TO USE THIS MANUAL
1 To help identify parts and clarify procedure steps, there are exploded diagrams at the start
of each removal and disassembly section.
2 Numbers are given in the order of the jobs in the exploded diagram.
3 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”).
4 A job instruction chart accompanies the exploded diagram, providing the order of jobs,
names of parts, notes in jobs, etc.
5 Dimension figures and the number of parts, are provided for fasteners that require a tightening torque.
Example:
Bolt or screw size
10 × 25 mm
: M10 (D) × 25 mm (L)
D
L
6 Jobs requiring more information (such as special tools and technical data) are described
sequentially.
E
1
A50001-1-4
2
GEN
INFO
SYMBOLS
Symbols 1 to 9 are designed as thumbtabs to indicate the content of a chapter.
SPEC
3
1
2
3
4
5
6
7
8
9
4
INSP
ADJ
FUEL
5
6
JET
PUMP
POWR
7
General Information
Specifications
Periodic Inspection and Adjustment
Fuel System
Power Unit
Jet Pump Unit
Electrical System
Hull and Hood
Trouble-analysis
8
–
ELEC
9
+
HULL
HOOD
Symbols 0 to E indicate specific data:
0
0
A
B
C
D
E
TRBL
ANLS
A
B
C
D
F
Symbol F to H in an exploded diagram
indicate the grade of lubricant and the location of lubrication point:
H
F Apply YAMALUBE 2-W oil
G Apply water resistant grease
(Yamaha grease A, Yamaha marine grease)
H Apply molybdenum disulfide grease
T.
R.
E
E
G
M
A
I
J
4
GM
K
L
LT
LT
271
242
M
N
LT
572
Special tool
Specified liquid
Specified engine speed
Specified torque
Specified measurement
Specified electrical value
[Resistance (Ω), Voltage (V), Electric current
(A)]
SS
LT
Symbols I to N in an exploded diagram
indicate the grade of the sealing or locking
agent, and the location of the application
point:
I Apply Gasket Maker
J Apply Yamabond #4
(Yamaha bond number 4)
K Apply LOCTITE No. 271 (Red LOCTITE)
L Apply LOCTITE No. 242 (Blue LOCTITE)
M Apply LOCTITE No. 572
N Apply silicone sealant
NOTE:
In this manual, the above symbols may not
be used in every case.
E
A30000-0
INDEX
GENERAL INFORMATION
SPECIFICATIONS
PERIODIC INSPECTION AND
ADJUSTMENT
FUEL SYSTEM
POWER UNIT
JET PUMP UNIT
GEN
INFO
SPEC
INSP
ADJ
FUEL
POWR
JET
PUMP
–
ELECTRICAL SYSTEM
HULL AND HOOD
TROUBLE-ANALYSIS
+
ELEC
HULL
HOOD
TRBL
ANLS
1
2
3
4
5
6
7
8
9
GEN
INFO
E
CHAPTER 1
GENERAL INFORMATION
IDENTIFICATION NUMBERS ......................................................................... 1-1
PRIMARY l.D. NUMBER........................................................................... 1-1
ENGINE SERIAL NUMBER ...................................................................... 1-1
JET PUMP UNIT SERIAL NUMBER ........................................................ 1-1
HULL IDENTIFICATION NUMBER (H.l.N.).............................................. 1-1
SAFETY WHILE WORKING....................................................................... 1-2
FIRE PREVENTION ................................................................................... 1-2
VENTILATION........................................................................................... 1-2
SELF-PROTECTION.................................................................................. 1-2
OILS, GREASES AND SEALING FLUIDS................................................ 1-2
GOOD WORKING PRACTICES ................................................................ 1-3
DISASSEMBLY AND ASSEMBLY ........................................................... 1-4
SPECIAL TOOLS ............................................................................................. 1-5
MEASURING ............................................................................................ 1-5
REMOVAL AND INSTALLATION ............................................................ 1-6
1
2
3
4
5
6
7
8
9
GEN
INFO
IDENTIFICATION NUMBERS
E
A60700-0*
IDENTIFICATION NUMBERS
PRIMARY l.D. NUMBER
The primary l.D. number is stamped on a
label attached to the inside of the engine
compartment.
Starting primary l.D. number:
F0D: 800101 ~
ENGINE SERIAL NUMBER
The engine serial number is stamped on a
label attached to the cylinder head.
Starting serial number:
66V: 000101 ~
JET PUMP UNIT SERIAL NUMBER
The jet pump unit serial number is stamped
on a label attached to the intermediate
housing.
Starting serial number:
66V: 800101 ~
HULL IDENTIFICATION NUMBER
(H.l.N.)
The H.l.N. is stamped on a plate attached to
the aft deck.
1-1
GEN
INFO
SAFETY WHILE WORKING
E
SAFETY WHILE WORKING
The procedures given in this manual are
those recommended by Yamaha to be followed by Yamaha dealers and their
mechanics.
FIRE PREVENTION
Gasoline (petrol) is highly flammable.
Petroleum vapor is explosive if ignited.
Do not smoke while handling gasoline
(petrol) and keep it away from heat, sparks,
and open flames.
VENTILATION
Petroleum vapor is heavier than air and is
deadly if inhaled in large quantities. Engine
exhaust gases are harmful to breathe.
When test-running an engine indoors,
maintain good ventilation.
SELF-PROTECTION
Protect your eyes with suitable safety spectacles or safety goggles when grinding or
doing any operation which may cause particles to fly off.
Protect hands and feet by wearing safety
gloves or protective shoes if appropriate to
the work you are doing.
OILS, GREASES AND SEALING
FLUIDS
Use only genuine Yamaha oils, greases,
and sealing fluids or those recommended
by Yamaha.
1-2
GEN
INFO
SAFETY WHILE WORKING
E
Under normal conditions of use there
should be no hazards from the use of the
lubricants mentioned in this manual, but
safety is all-important, and by adopting
good safety practises any risk is minimized.
A summary of the most important precautions is as follows:
1. While working, maintain good standards of personal and industrial
hygiene.
2. Clothing which has become contaminated with lubricants should be
changed as soon as practicable and
laundered before further use.
3. Avoid skin contact with lubricants (e.g.,
do not place a soiled rag in your
pocket).
4. Hands and any other part of the body
which have been in contact with lubricants or lubricant-contaminated clothing should be thoroughly washed with
hot water and soap as soon as practicable.
5. To protect the skin, the application of a
suitable barrier cream to the hands
before working is recommended.
6. A supply of clean lint-free cloths should
be available for wiping purposes.
GOOD WORKING PRACTICES
1. The right tools
Use the recommended special tools to
protect parts from damage. Use the
right tool in the right manner – do not
improvise.
2. Tightening torque
Follow the tightening torque instructions. When tightening bolts, nuts and
screws, tighten the larger sizes first and
tighten inner-positioned fixings before
outer-positioned ones.
1-3
GEN
INFO
SAFETY WHILE WORKING
E
3. Non-reusable items
Always use new gaskets, packings, Orings, oil seals, split-pins, circlips, etc.,
on reassembly.
DISASSEMBLY AND ASSEMBLY
1. Clean parts with compressed air when
disassembling.
2. Oil the contact surfaces of moving parts
during assembly.
3. After assembly, check that moving parts
operate normally.
4. Install bearings with the manufacturer’s
markings on the side exposed to view
and liberally oil the bearings.
CAUTION:
Do not spin bearings with compressed air
because this will damage their surfaces.
5. When installing oil seals, apply a light
coat of water-resistant grease to the
outside diameter.
1-4
GEN
INFO
SPECIAL TOOLS
E
SPECIAL TOOLS
Using the correct special tools recommended by Yamaha, will aid the work and
enable accurate assembly and tune-up.
Improvisations and using improper tools
can damage the equipment.
1
NOTE:
● For U.S.A. and Canada, use part numbers
starting with “YB-”, “YM-”, “YU-” or
“YW-”.
● For other countries, use part numbers
starting with “90890-”.
90890-01252
YU-03097
YU-01256
MEASURING
2
YU-34899-A
3
YU-03112
90890-03112
5
YU-33223
90890-03160
6
YU-08036-A
90890-06760
7
YM-34487
90890-06754
8
YW-06780
90890-06780
1. Dial gauge and stand
P/N. YU-03097, YU-01256
90890-01252
2. Digital multimeter
P/N. YU-34899-A
90890-06752
3. Pocket tester
P/N. YU-03112
90890-03112
4. Cylinder gauge set
P/N. YU-03017
90890-06759
5. Compression gauge
P/N. YU-33223
90890-03160
6. Engine tachometer
P/N. YU-08036-A
90890-06760
7. Spark gap tester
P/N. YM-34487
90890-06754
8. Peak voltage test harness
P/N. YW-06780
90890-06780
90890-06752
4
YU-03017
90890-06759
1-5
GEN
INFO
SPECIAL TOOLS
E
REMOVAL AND INSTALLATION
1
2
YW-06551
YW-06550
1. Coupler wrench
P/N. YW-06551
90890-06551
2. Flywheel holder
P/N. YW-06550
90890-06550
3. Flywheel puller
P/N. YB-06117
90890-06521
4. Shaft holder (intermediate shaft)
P/N. YB-06552
90890-06552
5. Driver rod
(intermediate shaft and jet pump)
P/N. YB-06071, YB-06229
90890-06602, 90890-06605,
90890-06606
6. Bearing outer race attachment
(intermediate shaft)
P/N. YB-06016
90890-06626
7. Drive shaft holder (impeller)
P/N. YB-06151
90890-06519
8. Slide hammer set (jet pump bearing)
P/N. YB-06096
90890-06523, 90890-06531
9. Ball bearing attachment
(jet pump oil seal)
P/N. YB-06156
90890-06634
10. Bearing inner race attachment
(jet pump bearing)
P/N. YB-34474
90890-06662
90890-06550
90890-06551
3
YB-06117
90890-06521
4 YB-06552
90890-06552
5
YB-06071
YB-06229
6
YB-06016
8
YB-06096
9
YB-06156
90890-06602
90890-06605
90890-06606
90890-06626
7
YB-06151
90890-06519
90890-06523
90890-06531
90890-06634
0
YB-34474
90890-06662
1-6
SPEC
E
CHAPTER 2
SPECIFICATIONS
GENERAL SPECIFICATIONS.......................................................................... 2-1
MAINTENANCE SPECIFICATIONS................................................................ 2-3
ENGINE..................................................................................................... 2-3
JET PUMP UNIT....................................................................................... 2-4
HULL AND HOOD .................................................................................... 2-4
ELECTRICAL ............................................................................................. 2-5
TIGHTENING TORQUES ................................................................................ 2-7
SPECIFIED TORQUES .............................................................................. 2-7
GENERAL TORQUE ................................................................................. 2-9
CABLE AND HOSE ROUTING...................................................................... 2-10
1
2
3
4
5
6
7
8
9
SPEC
GENERAL SPECIFICATIONS
E
GENERAL SPECIFICATIONS
Item
MODEL CODE
Hull
Engine
DIMENSIONS
Length
Width
Height
Dry weight
Vehicle capacity
PERFORMANCE
Maximum output
Maximum fuel consumption
Cruising range
ENGINE
Engine type
Number of cylinders
Displacement
Bore × stroke
Compression ratio
Intake system
Carburetor model
(manufacturer) × quantity
Enrichment control
Scavenging system
Lubrication system
Cooling system
Starting system
Ignition system
Ignition timing
Spark plug model
(manufacturer)
Battery capacity
Lighting coil
DRIVE UNIT
Propulsion system
Jet pump type
Impeller rotation
(from rear)
Transmission
Nozzle angle (horizontal)
Nozzle angle (vertical)
Trim system
Reverse system
Model
XL1200Ltd
Unit
F0D
66V
mm (in)
mm (in)
mm (in)
kg (lb)
3,160 (124.4)
1,220 (48.0)
1,130 (44.5)
354 (780)
3
kW (PS) @ r/min
R/h (US gal/h,
lmp gal/h)
hr
114.0 (155) @ 7,000
64.0 (16.9, 14.1)
cm3 (cu. in)
mm (in)
1.1
2-stroke
3
1,176 (71.7)
80.0 × 78.0 (3.15 × 3.07)
5.9:1
Reed valve
BN44 (MIKUNI) × 3
Choke valve
Loop charge
Variable oil injection
Water cooled
Electric starter
Digital CDI
18 BTDC ~ 24 BTDC
BR8ES-11 (NGK)
Degree
V-Ah (kC)
A @ r/min
12 - 19 (68.4)
9 ~ 11 @ 6,000
Jet pump
Axial flow, single stage
Counterclockwise
Direct drive from engine
24 + 24
–7, –2, 3, 8, 13
Manual 5 positions
Reverse gate
Degree
Degree
2-1
SPEC
GENERAL SPECIFICATIONS
Item
FUEL AND OIL
Fuel
Minimum fuel rating
Oil
Fuel/oil mixing ratio
(wide open throttle)
Fuel tank capacity
Fuel tank reserve capacity
Oil tank capacity
E
Model
XL1200Ltd
Unit
Regular unleaded gasoline
86
90
YAMALUBE 2-W*
30:1
PON*
RON*
R(US gal,
Imp gal)
R(US gal,
Imp gal)
R(US gal,
Imp gal)
70 (18.5, 15.4)
12 (3.17, 2.64)
5.5 (1.45, 1.21)
PON*: Pump Octane Number
RON*: Research Octane Number
YAMALUBE 2-W*: YAMALUBE 2-W is developed for this water vehicle and available from a
Yamaha water vehicle dealer.
CAUTION:
Use only YAMALUBE 2-W oil. Using another oil can seriously damage the catalytic converter
and other engine components.
2-2
SPEC
MAINTENANCE SPECIFICATIONS
E
MAINTENANCE SPECIFICATIONS
ENGINE
Item
CYLINDER HEAD
Warpage limit
Compression pressure*1
CYLINDERS
Bore size
Taper limit
Out-of-round limit
Wear limit
PISTONS
Diameter
Measuring point*
Piston-to-cylinder clearance
Wear limit
Piston pin bore inside
diameter
PISTON RINGS
Top
Type
Dimensions (B)
Dimensions (T)
End gap
Ring groove clearance
2nd
Type
Dimensions (B)
Dimensions (T)
End gap
Ring groove clearance
PISTON PINS
Diameter
Wear limit
Unit
Model
XL1200Ltd
mm (in)
KPa (kg/cm2)
0.1 (0.004)
500 (5.0)
mm (in)
mm (in)
mm (in)
mm (in)
80.000 ~ 80.018 (3.1496 ~ 3.1503)
0.08 (0.003)
0.05 (0.002)
Original cylinder bore + 0.04 (0.0016)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
Red: 79.899 ~ 79.902 (3.1456 ~ 3.1457)
Orange: 79.903 ~ 79.906 (3.1458 ~ 3.1459)
Green: 79.907 ~ 79.910 (3.1459 ~ 3.1461)
Purple: 79.911 ~ 79.914 (3.1461 ~ 3.1462)
22 (0.87)
0.100 ~ 0.105 (0.0039 ~ 0.0041)
Cylinder bore – 0.105 (0.0041)
22.004 ~ 22.025 (0.8663 ~ 0.8671)
mm (in)
mm (in)
mm (in)
mm (in)
Keystone
1.47 ~ 1.49 (0.058 ~ 0.059)
2.8 ~ 2.9 (0.110 ~ 0.114)
0.45 ~ 0.60 (0.018 ~ 0.024)
0.02 ~ 0.07 (0.001 ~ 0.003)
mm (in)
mm (in)
mm (in)
mm (in)
Keystone
1.47 ~ 1.49 (0.058 ~ 0.059)
2.8 ~ 2.9 (0.110 ~ 0.114)
0.45 ~ 0.60 (0.018 ~ 0.024)
0.02 ~ 0.07 (0.001 ~ 0.003)
mm (in)
mm (in)
21.995 ~ 22.000 (0.8659 ~ 0.8661)
21.990 (0.8657)
*1: At 760 mmHg and 20 ˚C (68 ˚F).
2-3
SPEC
MAINTENANCE SPECIFICATIONS
Item
CRANKSHAFT ASSEMBLY
Crank width A
Deflection limit B
Deflection limit C
Big end side clearance D
Maximum small end axial
play E
CARBURETORS
Type
Identification mark
Main nozzle
Main jet
Pilot jet
Throttle valve
Valve seat size
Trolling speed
REED VALVES
Thickness
Reed valve stopper height
Reed valve warpage limit
E
Unit
Model
XL1200Ltd
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
72.95 ~ 73.00 (2.872 ~ 2.874)
0.05 (0.002)
0.15 (0.006)
0.25 ~ 0.75 (0.010 ~ 0.030)
2.0 (0.08)
mm (in)
r/min
Floatless
#1: 66V-01, #2: 66V-02, #3: 66V-03
3.2 (0.13)
117.5
87.5
180
1.2 (0.05)
1,350 ± 50
mm (in)
mm (in)
mm (in)
0.6 (0.024)
10.4 ~ 11.0 (0.41 ~ 0.43)
0.2 (0.01)
Unit
Model
XL1200Ltd
mm (in)
JET PUMP UNIT
Item
JET PUMP
Impeller material
Number of impeller blades
Impeller pitch angle
Impeller clearance
Impeller clearance limit
Drive shaft runout limit
Nozzle diameter
Stainless steel
3
15.6
0.8 (0.031)
0.9 (0.035)
0.3 (0.012)
86.8 (3.42)
Degree
mm (in)
mm (in)
mm (in)
mm (in)
HULL AND HOOD
Item
FREE PLAY
YPVS cable slack
Throttle lever free play
Unit
Model
XL1200Ltd
mm (in)
mm (in)
0.5 ~ 1.5 (0.02 ~ 0.06)
4 ~ 7 (0.16 ~ 0.28)
2-4
SPEC
MAINTENANCE SPECIFICATIONS
E
ELECTRICAL
Item
BATTERY
Type
Capacity
CDI UNIT
(B/W – B)
Output peak voltage lower
limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
STATOR
Pickup coil
(W/R – B/O)
Output peak voltage
lower limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
Lighting coil
(G – G)
Output peak voltage
lower limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
Pickup coil resistance
Lighting coil resistance
Minimum charging current
IGNITION COIL
Minimum spark gap
Primary coil resistance
Secondary coil resistance
Spark plug lead resistance
#1
#2
#3
Model
XL1200Ltd
Unit
V-Ah (kC)
Fluid
12 - 19 (68.4)
V
V
V
V
200
180
190
180
V
V
V
V
5
2.8
7.9
11
V
V
V
V
Ω (color)
Ω (color)
A @ r/min
9
9
14
14
445 ~ 545 (W/R – B/O)
0.49 ~ 0.59 (G – G)
9 @ 6,000
mm (in)
Ω (color)
kΩ (color)
10 (0.39)
0.26 ~ 0.36 (B/W – Ground)
3.5 ~ 4.7 (B/W – Spark plug lead terminal)
kΩ
kΩ
kΩ
6.1 ~ 14.3
4.6 ~ 11.1
3.1 ~ 7.7
Cranking 1: unloaded
Cranking 2: loaded
2-5
SPEC
MAINTENANCE SPECIFICATIONS
Item
RECTIFIER/REGULATOR
(R – B)
Output peak voltage lower
limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
STARTER MOTOR
Brush length
Wear limit
Commutator undercut
Limit
Commutator diameter
Limit
FUSE
Rating
E
Unit
Model
XL1200Ltd
V
V
V
V
—
7
12.6
12.6
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
12.5 (0.49)
6.5 (0.26)
0.7 (0.03)
0.2 (0.01)
28.0 (1.10)
27.0 (1.06)
V-A
12-10
12-20
Cranking 1: unloaded
Cranking 2: loaded
2-6
SPEC
TIGHTENING TORQUES
E
TIGHTENING TORQUES
SPECIFIED TORQUES
20
2.0
14
Nut
M10
2
Bolt
M10
10
Nut
M10
2
Bolt
Bolt
Bolt
Screw
M6
M8
M8
M4
6
4
4
24
40
23
40
15
40
12
17
17
1
4.0
2.3
4.0
1.5
4.0
1.2
1.7
1.7
0.1
29
17
29
11
29
8.7
12
12
0.7
Bolt
M6
2
10
1.0
7.2
Bolt
Bolt
Bolt
M6
M5
M14
10
3
3
Bolt
M8
22
Bolt
M10
12
Bolt
M10
8
10
4
25
23
23
36
22
40
15
51
1.0
0.4
2.5
2.3
2.3
3.6
2.2
4.0
1.5
5.1
7.2
2.9
18
17
17
26
16
29
11
37
2-7
LT
1
271
—
LT
—
271
29
LT
4.0
242
40
LT
1
271
—
LT
—
271
6
LT
M8
271
Bolt
LT
6
29
29
29
29
11
25
8.8
17
271
M8
4.0
4.0
4.0
4.0
1.5
3.4
1.2
2.3
LT
Bolt
40
40
40
40
15
34
12
23
271
4
2
2
3
LT
M10
M10
M10
M10
271
Bolt
Bolt
Bolt
Bolt
LT
29
271
4.0
LT
40
572
6
LT
M10
572
Bolt
LT
8.7
271
1.2
LT
12
271
3
LT
M6
271
Bolt
LT
29
242
4.0
LT
40
572
4
LT
M10
572
Bolt
LT
2
242
M8
LT
Bolt
572
29
11
26
LT
4.0
1.5
3.6
572
40
15
36
LT
2
242
M10
Remarks
LT
Bolt
Tightening torque
Nm
m•kg ft•lb
572
Thread
Q’ty
size
LT
ENGINE
Exhaust chamber/stay – bracket
1st
Exhaust chamber stay/
cylinder head – cylinder
2nd
Exhaust chamber joint –
exhaust manifold
Muffler cover – muffler
Exhaust chamber –
exhaust chamber joint
Hanger – cylinder head
Muffler stay – cylinder body
Muffler stay 2 – crankcase
Muffler – stay
1st
Muffler – catalyst
housing
2nd
1st
Muffler – mixing joint
2nd
Exhaust temperature sensor –
muffler
Water temperature sensor –
mixing joint
Muffler – hanger
1st
2nd
Exhaust manifold –
cylinder
1st
2nd
Joint pipe – exhaust manifold
Electrical box – hull
Engine – engine mount
Reed valve – reed valve base
YPVS cable holder/valve cover –
cylinder
YPVS valve cover – cylinder
YPVS valve holder – shaft
Spark plug – cylinder head
1st
Cylinder head cover/
2nd
cylinder head – cylinder
3rd
1st
Cylinder – crankcase
2nd
1st
Generator cover –
crankcase
2nd
Part name
271
Part to tightened
TIGHTENING TORQUES
Bolt
M6
Bolt
LT
4
12
23
12
1.2
2.3
1.2
8.7
17
8.7
M20
1
18
1.8
13
Coupling
Bolt
Bolt
Bolt
Bolt
Bolt
Bolt
Nut
Nut
M27
M8
M6
M8
M8
M8
M8
M16
M10
1
3
4
4
4
2
2
1
4
37
17
8
17
17
16
16
70
27
3.7
1.7
0.8
1.7
1.7
1.6
1.6
7.0
2.7
27
12
5.8
12
12
12
12
51
20
Bolt
M8
4
17
1.7
12
LT
Bolt
M8
4
16
1.6
12
Nut
Bolt
Nut
Nut
Nut
Bolt
M8
M6
M10
M8
M8
M8
4
4
2
2
2
8
20
7
26
16
16
17
2.0
0.7
2.6
1.6
1.6
1.7
14
5.1
19
12
12
12
LT
LT
LT
LT
LT
LT
LT
LT
LT
LT
8.0
2-8
242
E
LT
6
1.1
271
M8
LT
Bolt
11
572
6
242
M6
242
Bolt
572
1
572
M27
271
Coupling
572
6
572
M8
572
Bolt
271
10
271
M6
572
JET PUMP UNIT
Impeller (left-hand threads) –
drive shaft
Driven coupling – shaft
Bearing housing – hull
Intake screen – hull
Intake duct – hull
Jet pump cover – hull
Nozzle deflector – nozzle ring
Nozzle ring – nozzle
Drive shaft nut – drive shaft
Transom plate – hull
HULL AND HOOD
Fuel tank belt – hull
Handlebar holder – steering
master
Steering master – deck
Seat lock assembly – seat
Seat lock notch – deck
Bow eye – hull
Cleat – deck
Engine mount – hull
17
LT
Engine bracket – lower
crankcase
Drive coupling – crankshaft
Intake silencer plate/carburetor –
cylinder
1st
Carburetor assembly –
2nd
cylinder
M8
Bolt
Remarks
LT
1st
2nd
Bolt
Bolt
Tightening torque
Nm
m•kg ft•lb
15
1.5
11
75
7.5
54
15
1.5
11
28
2.8
20
11
1.1
8.0
15
1.5
11
28
2.8
20
37
3.7
27
572
Stator coil – generator cover
Flywheel magneto – crankshaft
1st
Upper crankcase – lower
2nd
crankcase
Thread
Q’ty
size
M6
3
M10
1
271
Part name
LT
Part to tightened
E
572
SPEC
SPEC
TIGHTENING TORQUES
Nut A
Bolt B
8 mm
10 mm
12 mm
14 mm
17 mm
M5
M6
M8
M10
M12
E
GENERAL TORQUE
General torque
specifications
Nm m•kg ft•lb
5.0
0.5
3.6
8.0
0.8
5.8
18
1.8
13
36
3.6
25
43
4.3
31
This chart specifies tightening torques for
standard fasteners with a standard ISO
thread pitch. Tightening torque specifications for special components or assemblies
are provided in applicable sections of this
manual. To avoid warpage, tighten multifastener assemblies in a crisscross fashion
and progressive stages until the specified
tightening torque is reached. Unless otherwise specified, tightening torque specifications require clean, dry threads.
Components should be at room temperature.
2-9
SPEC
CABLE AND HOSE ROUTING
E
CABLE AND HOSE ROUTING
1
2
3
4
5
6
7
8
Fuel breather hose
Pilot water hose
QSTS cable
Fuel hose
Shift cable
Steering cable
Fuel filter
Ventilation hose
9
0
A
B
C
D
E
F
Ground lead
Starter motor lead
Electrical box lead
Generator lead
Pickup coil lead
YPVS cable
Speed sensor lead
Pilot water outlet
2-10
G
H
I
J
K
L
M
Battery
Battery breather hose
Battery positive lead
Battery negative lead
Choke knob
Fuel cock
Choke cable
SPEC
1
2
3
4
5
6
7
8
CABLE AND HOSE ROUTING
Throttle cable
Switch box lead
QSTS cable
Buzzer lead
To pickup coil
To battery positive terminal
To starter motor
To multi-function meter
9 To water/exhaust
temperature sensor
0 To generator
A Battery breather hose
B Battery negative lead
C Water hose
D Speed sensor lead
E Fuel breather hose
2-11
E
F
G
H
I
J
To fuel filter
Choke cable
Fuel return hose
Shift cable
Steering cable
INSP
ADJ
E
CHAPTER 3
PERIODIC INSPECTION AND ADJUSTMENT
MAINTENANCE INTERVAL CHART .............................................................. 3-1
PERIODIC SERVICE ........................................................................................ 3-2
CONTROL SYSTEM ................................................................................. 3-2
Steering master inspection .............................................................. 3-2
Steering cable inspection and adjustment ..................................... 3-2
Throttle cable inspection and adjustment ...................................... 3-3
Choke cable inspection and adjustment ......................................... 3-4
QSTS cable inspection and adjustment .......................................... 3-4
Shift cable inspection and adjustment............................................ 3-6
YPVS cable adjustment .................................................................... 3-7
FUEL SYSTEM.......................................................................................... 3-8
Fuel line inspection ........................................................................... 3-9
Trolling speed check and adjustment ............................................. 3-9
OIL INJECTION SYSTEM....................................................................... 3-10
Oil filter inspection.......................................................................... 3-10
Oil injection pump air bleeding ..................................................... 3-10
POWER UNIT.......................................................................................... 3-11
Spark plug inspection ..................................................................... 3-11
ELECTRICAL ........................................................................................... 3-12
Battery inspection ........................................................................... 3-12
JET PUMP UNIT..................................................................................... 3-15
Impeller inspection ......................................................................... 3-15
Water inlet filter inspection ............................................................ 3-16
Bilge strainer inspection................................................................. 3-16
GENERAL................................................................................................ 3-16
Drain plug inspection...................................................................... 3-16
Lubrication points ........................................................................... 3-17
1
2
3
4
5
6
7
8
9
INSP
ADJ
MAINTENANCE INTERVAL CHART
E
MAINTENANCE INTERVAL CHART
The following chart should be considered strictly as a guide to general maintenance intervals.
Depending on operating conditions, the intervals of maintenance should be changed.
Initial
Item
CONTROL SYSTEM
Steering cable
Steering master
Throttle cable
Carburetor throttle shaft
Choke cable
Shift cable
QSTS
YPVS
FUEL SYSTEM
Fuel tank
Fuel filter
Fuel line
Trolling speed
Carburetor setting
OIL INJECTION SYSTEM
Oil injection system
Oil pump cable
POWER UNIT
Spark plugs
Cooling-water passage
Rubber coupling
ELECTRICAL
Battery
JET PUMP UNIT
Impeller
Water inlet filter
Bilge strainer
GENERAL
Bolts and nuts
Drain plugs
Lubrication points
Bearing housing
Remarks
Every
10 hours 50 hours 100 hours 200 hours
(Break-in) (3 months) (6 months) (1 year)
Refer to
page
Inspect/adjust
Inspect
Inspect/adjust
Inspect/adjust
Inspect/adjust
Inspect/adjust
Inspect/adjust
Inspect/adjust
3-2
3-2
3-3
—
3-4
3-6
3-4
3-7
Clean
Clean/replace
Inspect
Check/adjust
Inspect/adjust
4-7
3-9
—
3-9
4-16
Check/clean
Inspect/adjust
3-10
4-31
Inspect/clean/adjust
Inspect/clean
Inspect
3-11
—
—
*3
*4
Inspect
3-12
Inspect
Clean
Clean
3-15
3-16
3-16
Retighten
Inspect/replace
Grease
Grease
—
3-16
3-17
3-18
*1
*1: Grease capacity 33.0 ~ 35.0 cm3 (1.11 ~ 1.18 oz.)
*2: Grease capacity 6.0 ~ 8.0 cm3 (0.20 ~ 0.27 oz.)
*3: After every ride
*4: Inspect fluid level before every ride
3-1
*2
INSP
ADJ
CONTROL SYSTEM
E
PERIODIC SERVICE
CONTROL SYSTEM
Steering master inspection
1. Inspect:
● Steering master
Excessive play → Replace the steering master.
Refer to “STEERING MASTER” in
chapter 8.
Inspection steps:
● Move the handlebar up and down and
back and forth.
● Check the excessive play of the handlebar.
Steering cable inspection and adjustment
1. Inspect:
● Jet nozzle clearance a, b
Difference → Adjust.
Inspection steps:
● Turn the handlebar from lock to lock.
● Measure clearances a and b.
● If clearances a and b are not the
same, adjust them.
2. Adjust:
● Steering cable joint
(steering column side)
Adjustment steps:
Loosen the locknut 1.
● Disconnect the steering cable joint 2
from the ball joint 3.
● Turn the cable joint in or out for adjusting the clearance.
●
3-2
Turn in
Clearance a is increased.
Turn out
Clearance b is increased.
INSP
ADJ
CONTROL SYSTEM
E
WARNING
The cable joint must be screwed in more
than 8 mm (0.31 in).
●
Connect the cable joint and tighten the
locknut.
T.
Locknut:
7 Nm (0.7 m • kg, 5.1 ft • lb)
R.
NOTE:
If the steering cable cannot be properly
adjusted at the steering column side, make
adjustments at the jet pump side.
Throttle cable inspection and adjustment
NOTE:
Before adjusting the throttle lever free play,
adjust the trolling speed.
1. Measure:
● Throttle lever free play a
Out of specification → Adjust.
Throttle lever free play:
4 ~ 7 mm (0.16 ~ 0.28 in)
2. Adjust:
● Throttle lever free play
Adjustment steps:
● Loosen the locknut 1.
● Turn the adjuster 2 in or out until the
specified free play is obtained.
Turn in
Free play is increased.
Turn out
Free play is decreased.
●
Tighten the locknut.
WARNING
After adjusting the free play, turn the handlebar to the right and left and make sure
that the trolling speed does not increase.
3-3
INSP
ADJ
CONTROL SYSTEM
E
Choke cable inspection and adjustment
1. Inspect:
● Choke knob
(pull the choke knob all the way out)
Choke knob automatically returns →
Adjust.
Adjustment steps:
● Turn in the adjusting nut 1 until the
choke knob does not automatically
return.
QSTS cable inspection and adjustment
1. Measure:
● Nozzle deflector set length a, b
Difference → Adjust.
Measurement steps:
● Set the control grip in the neutral position.
● Set the jet nozzle in the center position.
● Measure the nozzle deflector set
length a and b.
● If a and b length are not even, adjust
the cable joint.
3-4
INSP
ADJ
CONTROL SYSTEM
E
2. Adjust:
● QSTS cable
Adjustment steps:
● Set the control grip in the neutral position.
● Set the jet nozzle in the center position.
● Remove the nut 1 and pivot pin 2.
● Loosen the locknut 3.
● Turn the cable joint 4 for adjusting.
Turn in
Length b is increased.
Turn out
Length a is increased.
WARNING
The cable joint must be screwed in more
than 8 mm (0.31 in).
●
Connect the cable joint 4 and pivot
pin 2 and tighten the nut 1.
T.
Nut:
4 Nm (0.4 m • kg, 2.9 ft • lb)
R.
●
Tighten the locknut 3.
T.
Locknut:
4 Nm (0.4 m • kg, 2.9 ft • lb)
R.
NOTE:
If correct adjustment by using the cable
joint at the wheel end is not obtained,
adjust the cable joint on the trim nozzle end.
3-5
INSP
ADJ
CONTROL SYSTEM
E
Shift cable inspection and adjustment
1. Check:
● Reverse gate stopper lever position
Incorrect → Adjust.
Checking steps:
Set the shift lever to the reverse position.
● Check to make sure the reverse gate 1
contacts the stopper 2 on the bracket
and the lever 3 contacts the reverse
gate.
●
2. Adjust:
● Shift cable joint
Adjustment steps:
● Loosen the locknut 1.
● Disconnect the cable joint 2 from the
ball joint 3.
● Turn the cable joint to align it with the
ball joint.
Turn in
Shortens.
Turn out
Lengthens.
●
Turn out the cable joint nine times
from the aligned position.
WARNING
The cable joint must be screwed in more
than 8 mm (0.31 in).
●
Connect the cable joint and tighten the
locknut.
T.
R.
3-6
Locknut:
3 Nm (0.3 m • kg, 2.2 ft • lb)
INSP
ADJ
CONTROL SYSTEM
E
YPVS cable adjustment
1. Check:
● YPVS valve position
Incorrect position → Adjust the YPVS
cable.
Checking steps:
Initiate the multi-function meter
“START” mode so the display comes
on.
● Start the engine and then stop it.
NOTE:
When the engine has been stopped for 3
seconds, the YPVS valve assembly will
extend and retract one time.
●
●
Check that the hole a in the pulley is
aligned with the hole in the cylinder
when the YPVS valve is fully closed.
2. Measure:
● YPVS cable slack a
Out of specification → Adjust.
YPVS cable slack:
0.5 ~ 1.5 mm (0.02 ~ 0.06 in)
3-7
INSP
ADJ
CONTROL SYSTEM/FUEL SYSTEM
E
3. Adjust:
● YPVS cables 1 and 2
Adjustment steps:
Loosen locknuts 1 and 2.
● Turn in the adjuster 3 and 4 until
there is slack in the cable.
● Align the hole a in the pulley with the
hole in the cylinder.
● Insert a 4-mm-diameter pin through
the holes in the pulley and cylinder.
● Turn the adjuster 3 and 4 in or out
until the specified slack is obtained.
●
Turn in
Slack is increased.
Turn out
Slack is decreased.
●
●
●
●
●
●
Finger tighten the locknut 1 and 2.
Remove the pin.
Start and stop the engine.
Recheck the hole alignment.
If the hole alignment is correctly,
tighten the locknut.
If the hole alignment is incorrect,
repeat the above steps.
FUEL SYSTEM
WARNING
● Stop
the engine, set the fuel cock to
“OFF” and loosen the fuel filler cap before
servicing the fuel system.
● When removing fuel system parts, wrap
them in a cloth and take care that no fuel
spills into the engine compartment.
3-8
INSP
ADJ
FUEL SYSTEM
E
Fuel line inspection
1. Inspect:
● Fuel filter 1
Contaminants → Replace.
Cracks/damage → Replace.
Water contamination → Replace and
check the fuel tank.
● Fuel hose
● Fuel tank
● Fuel hoses through part
● Fuel filler cap
Cracks/damage → Replace.
2. Inspect:
● Water separator 1
Water accumulation → Drain.
NOTE:
If need the water draining, remove the drain
plug 2.
Trolling speed check and adjustment
1. Check:
● Trolling speed
Out of specification → Adjust.
Trolling speed:
1,350 ± 50 r/min
Checking steps (with the vehicle in the
water):
● Start the engine and allow it to warm
up for several minutes.
● Attach the engine tachometer to the
spark plug lead.
Engine tachometer:
YU-8036-A/90890-06760
●
3-9
Measure the engine trolling speed.
INSP
ADJ
FUEL SYSTEM/OIL INJECTION SYSTEM
E
2. Adjust:
● Trolling speed
Adjustment steps:
Start the engine and allow it to warm
up for several minutes.
● Attach the engine tachometer to the
spark plug lead.
●
Engine tachometer:
YU-8036-A/90890-06760
●
Turn the remote throttle stop screw 1
in or out until the specified trolling
speed is obtain.
OIL INJECTION SYSTEM
Oil filter inspection
1. Inspect:
● Oil filter
Contaminants → Clean.
Frays/tears → Replace.
● Rubber seal
Cracks/wear → Replace.
Oil injection pump air bleeding
NOTE:
Bleed the oil injection system if:
● the system has been disassembled, or
● the oil has been completely depleted during operation.
3-10
INSP
ADJ
OIL INJECTION SYSTEM/POWER UNIT
E
1. Bleed:
● Air
Air bleeding steps:
Place rags around the air bleed screw
1 to catch any oil that might spill.
● Fill the oil tank with oil.
●
Recommended engine oil:
YAMALUBE 2-W oil only
●
●
●
Loosen the air bleed screw 1 two full
turns and make sure that both the oil
and air bubbles flow out.
When there are no air bubbles left,
tighten the air bleed screw.
Wipe up any spilt oil.
T.
Screw:
5 Nm (0.5 m • kg, 3.6 ft • lb)
R.
POWER UNIT
Spark plug inspection
1. Inspect:
● Electrodes 1
Damage/wear → Replace.
● Insulator color 2
Distinctly different color → Check the
engine condition.
Color guide:
Medium to light tan color:
Normal
Whitish color:
Lean fuel mixture
Air leak
Incorrect settings
Blackish color:
Overly rich mixture
Electrical malfunction
Excessive oil use
Defective spark plug
2. Clean:
● Spark plug
(with a spark plug cleaner or wire
brush)
3-11
INSP
ADJ
POWER UNIT/ELECTRICAL
E
3. Measure:
● Spark plug gap a
Out of specification → Regap.
Spark plug gap:
1.0 ~ 1.1 mm (0.039 ~ 0.043 in)
4. Tighten:
● Spark plug
T.
Spark plug:
25 Nm (2.5 m • kg, 18 ft • lb)
R.
NOTE:
● Before installing the spark plug, clean the
gasket surface and spark plug surface.
Also, it is suggested to apply a thin film of
anti-seize compound to the spark plug
threads to prevent thread seizure.
● If a torque wrench is not available, a good
estimate of the correct tightening torque
for a new spark plug is to finger tighten a
the spark plug and then tighten it another
1/4 to 1/2 of a turn b.
ELECTRICAL
Battery inspection
WARNING
Battery electrolyte is dangerous; it contains
sulfuric acid which is poisonous and highly
caustic.
Always follow these preventive measures:
● Avoid bodily contact with electrolyte as it
can cause severe burns or permanent eye
injury.
● Wear protective eye gear when handling
or working near batteries.
3-12
INSP
ADJ
ELECTRICAL
E
Antidote (EXTERNAL):
● SKIN - Wash with water.
● EYES - Flush with water for 15 minutes
and get immediate medical attention.
Antidote (INTERNAL):
● Drink large quantities of water or milk followed with milk of magnesia, beaten egg
or vegetable oil. Get immediate medical
attention.
Batteries generate explosive, hydrogen
gas. Always follow these preventive measures:
● Charge batteries in a well-ventilated area.
● Keep batteries away from fire, sparks or
open flames (e.g., welding equipment,
lighted cigarettes).
● DO NOT SMOKE when charging or handling batteries.
KEEP BATTERIES AND ELECTROLYTE OUT
OF REACH OF CHILDREN.
CAUTION:
● Do
not place the battery on its side.
● Before adding electrolyte or recharging,
be sure to remove the battery from the
battery box.
● Make sure that the battery breather hose
is properly connected and is not pinched
or damaged.
1. Remove:
● Battery
WARNING
● When
removing the battery, disconnect
the negative lead first.
● Remove the battery to prevent acid loss
during the impeller service.
3-13
INSP
ADJ
ELECTRICAL
E
2. Inspect:
● Electrolyte level
Low → Add distilled water.
The electrolyte level should be
between the upper 1 and lower 2
level marks.
Filling steps:
Remove each filler cap.
● Add distilled water.
● When the electrolyte level reaches the
upper level mark, allow the cell to
stand for 20 minutes. If the electrolyte
level drops, add more distilled water
so the level reaches the upper level
mark.
●
CAUTION:
Use only distilled water. Other types of
water contain minerals which are harmful
to batteries.
3. Inspect:
● Specific gravity
Out of specification → Charge.
Specific gravity at 20 ˚C (68 ˚F):
1.28
Charging current:
1.9 amps × 10 hrs (68.4 kC.)
4. Install:
● Filler caps
CAUTION:
Before installation, rinse off any fluid from
the battery box and battery and make sure
that the battery is dry before installing it.
3-14
INSP
ADJ
ELECTRICAL/JET PUMP UNIT
E
5. Install:
● Battery breather hose 1
● Battery
● Positive lead 2
● Negative lead 3
● Battery band
CAUTION:
● Connect
the positive lead to the battery
terminal first.
● Make sure the battery leads are connected properly. Reversing the leads can
seriously damage the electrical system.
● Make sure that the battery breather hose
is properly connected and is not
obstructed.
● Coat the terminals with a water resistant
grease to minimize terminal corrosion.
JET PUMP UNIT
Impeller inspection
1. Check:
● Impeller 1
Damage/wear → Replace.
Nicks/scratches → File or grind.
2. Measure:
● Impeller-to-housing clearance a
Out of specification → Replace.
Max. impeller-to-housing
clearance:
0.9 mm (0.035 in)
Measurement steps:
Remove the battery leads.
● Remove the intake screen 1 and duct
2.
● Measure the clearance at each impeller blade as shown (a total of four
measurements).
● Install the intake screen.
●
T.
R.
●
3-15
Bolt:
M6: 8 Nm (0.8 m • kg, 5.8 ft • lb)
M8: 17 Nm (1.7 m • kg, 12 ft • lb)
Install the battery leads.
INSP
ADJ
JET PUMP UNIT/GENERAL
E
Water inlet filter inspection
1. Inspect:
● Water inlet filter
Contaminants → Clean.
Cracks/damage → Replace.
Inspection steps:
Remove the water inlet cover 1.
● Inspect the water inlet filter mesh a.
● Reinstall the removed parts.
●
Bilge strainer inspection
1. Inspect:
● Bilge strainer
Contaminants → Clean.
Cracks/damage → Replace.
Inspection steps:
● Remove the coupling cover.
● Disconnect the bilge strainer 1 from
the bilge strainer holder.
● Inspect the bilge strainer.
GENERAL
Drain plug inspection
1. Inspect:
● Drain plug
Cracks/damage → Replace.
● O-ring
Cracks/wear → Replace.
● Screw threads
Contaminants → Clean.
3-16
INSP
ADJ
GENERAL
E
Lubrication points
1. Lubricate:
● Throttle cable (handlebar side)
● QSTS control cables (handlebar side)
Recommended lubricant:
Rust inhibitor
NOTE:
● Before lubricating the throttle cable,
squeeze the throttle lever and remove the
rubber seal 1.
● Before lubricating the QSTS control
cables, remove the trim grip guide.
2. Lubricate:
● Throttle cable (carburetor side)
● Oil pump cable
● QSTS cables (pulley side)
● YPVS cables
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
3-17
INSP
ADJ
GENERAL
E
3. Lubricate:
● Nozzle pivot shaft
● Steering cable (nozzle side)
● QSTS cable (nozzle side)
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
4. Lubricate:
● Steering cable
● Steering cable joint
● Shift cable
● Shift cable joint
NOTE:
Disconnect the joints and apply a small
amount of grease.
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
5. Fill:
● Bearing housing
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
NOTE:
● Fill the bearing housing with water resistant grease through the grease nipples.
● Add the grease slowly and carefully or it
could damage the hose and the joints.
Refer to “MAINTENANCE INTERVAL
CHART”.
3-18
FUEL
E
CHAPTER 4
FUEL SYSTEM
FUEL COCK AND FUEL FILTER ..................................................................... 4-1
EXPLODED DIAGRAM ............................................................................. 4-1
REMOVAL AND INSTALLATION CHART ............................................... 4-1
SERVICE POINTS ..................................................................................... 4-2
Fuel filter inspection ......................................................................... 4-2
Fuel cock inspection.......................................................................... 4-2
CHOKE CABLE ................................................................................................ 4-3
EXPLODED DIAGRAM ............................................................................. 4-3
REMOVAL AND INSTALLATION CHART ............................................... 4-3
OIL TANK ........................................................................................................ 4-4
EXPLODED DIAGRAM ............................................................................. 4-4
REMOVAL AND INSTALLATION CHART ............................................... 4-4
SERVICE POINTS ..................................................................................... 4-6
Oil filter inspection............................................................................ 4-6
Oil level switch inspection................................................................ 4-6
Oil tank inspection ............................................................................ 4-6
FUEL TANK ..................................................................................................... 4-7
EXPLODED DIAGRAM ............................................................................. 4-7
REMOVAL AND INSTALLATION CHART ............................................... 4-7
SERVICE POINTS ..................................................................................... 4-9
Check valve inspection ..................................................................... 4-9
Fuel level switch inspection ............................................................. 4-9
Fuel tank inspection .......................................................................... 4-9
Pipe joint inspection ......................................................................... 4-9
INTAKE DUCT AND SILENCER ................................................................... 4-10
EXPLODED DIAGRAM ........................................................................... 4-10
REMOVAL AND INSTALLATION CHART ............................................. 4-10
CARBURETOR UNIT..................................................................................... 4-12
EXPLODED DIAGRAM ........................................................................... 4-12
REMOVAL AND INSTALLATION CHART ............................................. 4-12
SERVICE POINTS ................................................................................... 4-16
Throttle valve synchronization inspection and adjustment ........ 4-16
Choke cable and throttle cable installation................................... 4-17
Oil pump cable installation ............................................................ 4-17
Carburetor assembly ...................................................................... 4-17
FUEL
CARBURETOR .............................................................................................. 4-18
EXPLODED DIAGRAM ........................................................................... 4-18
REMOVAL AND INSTALLATION CHART ............................................. 4-18
SERVICE POINTS ................................................................................... 4-21
Diaphragm inspection .................................................................... 4-21
Accelerator pump body inspection ............................................... 4-21
Arm inspection ................................................................................ 4-21
Regulator body inspection ............................................................. 4-22
Needle valve inspection ................................................................. 4-22
Jet and carburetor body inspection .............................................. 4-22
Carburetor assembly ...................................................................... 4-22
FUEL PUMP .................................................................................................. 4-23
EXPLODED DIAGRAM ........................................................................... 4-23
REMOVAL AND INSTALLATION CHART ............................................. 4-23
SERVICE POINTS ................................................................................... 4-25
Fuel pump inspection ..................................................................... 4-25
Fuel filter inspection ....................................................................... 4-25
OIL PUMP...................................................................................................... 4-26
EXPLODED DIAGRAM ........................................................................... 4-26
REMOVAL AND INSTALLATION CHART ............................................. 4-26
SERVICE POINTS ................................................................................... 4-29
Oil pump inspection........................................................................ 4-29
Oil hose inspection ......................................................................... 4-29
Check valve inspection ................................................................... 4-29
Oil pump cable adjustment ............................................................ 4-30
E
1
2
3
4
5
6
7
8
9
FUEL
FUEL COCK AND FUEL FILTER
E
FUEL COCK AND FUEL FILTER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
FUEL COCK AND FUEL FILTER
REMOVAL
Screw
Knob
Nut
Washer
Fuel cock assembly
Fuel hose
Holder
Fuel filter
Fuel hose
Q’ty
Service points
Follow the left “Step” for removal.
1
1
1
1
1
3
1
1
1
Reverse the removal steps for installation.
4-1
FUEL
FUEL COCK AND FUEL FILTER
E
SERVICE POINTS
Fuel filter inspection
Refer to “FUEL SYSTEM” in chapter 3.
Fuel cock inspection
1. Check:
● Fuel cock
Contaminants → Clean.
Rough movement → Replace.
4-2
FUEL
CHOKE CABLE
E
CHOKE CABLE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
CHOKE CABLE REMOVAL
Screw
Knob
Friction adjusting nut
Nut
Choke cable
Q’ty
Service points
Follow the left “Step” for removal.
1
1
1
1
1
Reverse the removal steps for installation.
4-3
FUEL
OIL TANK
E
OIL TANK
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
OIL TANK REMOVAL
Exhaust chamber assembly
Intake duct
Hose clamp
Oil filler cap
Screw
Oil filler neck
Rubber seal
Oil level sensor coupler
Q’ty
1
1
6
1
1
1
4-4
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY” in chapter 5.
Refer to “INTAKE DUCT AND SILENCER”.
FUEL
OIL TANK
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
Procedure/Part name
Breather hose
Oil hose
Bolt
Tank belt
Oil tank assembly
Hose clamp
Oil filler hose
Oil level sensor
Q’ty
1
1
2
2
1
1
1
1
Service points
Reverse the removal steps for installation.
4-5
FUEL
OIL TANK
E
SERVICE POINTS
Oil filter inspection
Refer to “OIL INJECTION SYSTEM” in
chapter 3.
Oil level switch inspection
Refer to “INDICATION SYSTEM” in
chapter 7.
Oil tank inspection
1. Inspect:
● Oil tank
Cracks/damage → Replace.
4-6
FUEL
FUEL TANK
E
FUEL TANK
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
FUEL TANK REMOVAL
Engine unit
Oil tank
Hose clamp
Fuel filler cap
Nut
Fuel filler neck
Rubber seal
Fuel level sensor coupler
Fuel reserve hose
Q’ty
1
1
1
1
1
1
1
4-7
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
Refer to “OIL TANK”.
FUEL
FUEL TANK
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
16
17
Procedure/Part name
Fuel hose
Fuel breather hose
Fuel tank assembly
Hose clamp
Fuel filler hose
Hose clamp
Fuel sensor assembly
One way valve
Screw
Filter
Q’ty
1
1
1
1
1
1
1
1
1
1
Service points
Reverse the removal steps for installation.
4-8
FUEL
FUEL TANK
E
SERVICE POINTS
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
●
Fuel level switch inspection
Refer to “INDICATION SYSTEM” in
chapter 7.
Fuel tank inspection
1. Inspect:
● Fuel tank
Cracks/damage → Replace.
Pipe joint inspection
1. Inspect:
● Pipe
Contaminants → Clean.
Bends/damage → Replace.
4-9
FUEL
INTAKE DUCT AND SILENCER
INTAKE DUCT AND SILENCER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
INTAKE DUCT AND SILENCER
REMOVAL
Exhaust chamber assembly
Q’ty
Refer to “EXHAUST CHAMBER
ASSEMBLY” in chapter 5.
Refer to “MUFFLER ASSEMBLY” in
chapter 5.
Muffler assembly
1
2
3
4
Hose clamp
Joint hose
Bolt
Intake duct
Service points
Follow the left “Step” for removal.
2
1
1
1
4-10
E
FUEL
INTAKE DUCT AND SILENCER
E
EXPLODED DIAGRAM
Step
5
6
7
8
9
10
Procedure/Part name
Hook
Silencer case
Bolt
Filter
Silencer plate
O-ring
Q’ty
5
1
6
1
1
3
Service points
Reverse the removal steps for installation.
4-11
FUEL
CARBURETOR UNIT
E
CARBURETOR UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
CARBURETOR UNIT REMOVAL
Silencer
Oil pump cable
Throttle cable
Choke cable
Fuel delivery hose
Fuel return hose
Oil delivery hose
Q’ty
1
1
1
1
1
3
4-12
Service points
Follow the left “Step” for removal.
Refer to “INTAKE DUCT AND SILENCER”.
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
Procedure/Part name
Fuel pump vacuum hose
Bolt
Bolt
Carburetor assembly
Gasket
Q’ty
3
6
4
1
1
4-13
Service points
Not reusable
Reverse the removal steps for installation.
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
CARBURETOR UNIT
SEPARATION
Hose
Hose
Accelerator pump hose
Remote throttle stop screw
assembly
Throttle link
Choke link
Q’ty
2
2
3
1
1
1
4-14
Service points
Follow the left “Step” for removal.
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
Procedure/Part name
Bolt
Cable holder
Bolt
Carburetor
Gasket
Plate
Q’ty
3
1
6
3
3
1
Service points
Not reusable
Reverse the removal steps for installation.
4-15
FUEL
CARBURETOR UNIT
E
SERVICE POINTS
Throttle valve synchronization inspection
and adjustment
1. Check:
● Throttle valve synchronization
Different clearances → Adjust.
Checking steps:
● Loosen the remote throttle stop screw
1 until untouched the screw end from
the throttle lever.
● Check the each throttle valve is fully
closed.
2. Adjust:
● Throttle valve synchronization
Adjustment steps:
● Loosen the remote throttle stop screw
1 until untouched the screw end from
the throttle lever.
● Loosen the screws 2.
NOTE:
Make sure that the throttle valves are in
the fully closed position.
●
Tighten the screws 2.
T.
Screw:
2 Nm (0.2 m • kg, 1.4 ft • lb)
R.
●
4-16
Turn in the remote throttle stop screw
to the original position.
FUEL
CARBURETOR UNIT
E
Choke cable and throttle cable installation
1. Install:
● Choke cable 1
● Throttle cable 2
Choke cable guide installation
position a:
13 ~ 15 mm (0.51 ~ 0.59 in)
Throttle cable guide installation
position b:
18 ~ 20 mm (0.71 ~ 0.79 in)
2. Adjust:
● Throttle lever free play
Refer to “CONTROL SYSTEM” in
chapter 3.
Oil pump cable installation
1. Adjust:
● Oil pump cable
Refer to “OIL PUMP”.
Carburetor assembly
1. Adjust:
● Trolling speed
Refer to “FUEL SYSTEM” in chapter 3.
4-17
FUEL
CARBURETOR
E
CARBURETOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
CARBURETOR DISASSEMBLY
Accelerator pump delivery hose
Accelerator pump fuel hose
Screw
Accelerator pump/carburetor
cover
Diaphragm
Screw
Regulator body
Gasket
Main jet
Q’ty
3
1
4
1/1
1
2
1
1
1
4-18
Service points
Follow the left “Step” for disassembly.
Carburetor #3
Carburetor #3
Carburetor #3/carburetor #1 and #2
FUEL
CARBURETOR
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
16
17
18
19
Procedure/Part name
Pilot jet
Screw
Arm
Arm pin
Spring
Screw
Needle valve seat holder
Needle valve
Needle valve seat
O-ring
Q’ty
1
1
1
1
1
1
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
4-19
FUEL
CARBURETOR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
ACCELERATOR PUMP
DISASSEMBLY
Screw
Stay
Spring
Spring seat
Screw
Accelerator pump cover assembly
Spring
Diaphragm
Accelerator pump body
Q’ty
Service points
Follow the left “Step” for disassembly.
1
1
1
1
4
1
1
1
1
Reverse the disassembly steps for
assembly.
4-20
FUEL
CARBURETOR
E
SERVICE POINTS
CAUTION:
Do not use steel wire for cleaning the jets.
This may enlarge the jet diameters and
seriously affect performance.
Diaphragm inspection
1. Inspect:
● Diaphragm
Damage → Replace.
Accelerator pump body inspection
1. Inspect:
● One way valve
Crack/damage → Replace the accelerator pump body.
● Fuel passage
Clog → Clean or replace.
Arm inspection
1. Inspect:
● Arm 1
Bends/damage → Repair or replace.
2. Measure:
● Arm height a
Arm height:
0 ~ 0.2 mm (0 ~ 0.008 in)
NOTE:
● Measure the distance between the surface
of the carburetor body b and the top surface of the arm.
● The arm should be resting on the needle
valve, but not compressing it.
4-21
FUEL
CARBURETOR
E
Regulator body inspection
1. Inspect:
● Regulator body
Contaminants → Clean.
Damage → Replace.
● Valve (clear film) 1
Damage → Replace.
Needle valve inspection
1. Inspect:
● Needle valve
● Needle valve seat
Contaminants a → Clean.
Wear b → Replace.
NOTE:
Always replace the needle valve and needle
valve seat as a set.
Jet and carburetor body inspection
1. Inspect:
● Main jet
● Pilot jet
● Carburetor body
Clog/contaminants → Clean.
Damage/wear → Replace.
CAUTION:
Do not use a steel wire to clean the jets.
This may enlarge the jet diameters and
seriously affect performance.
Carburetor assembly
1. Adjust:
● Trolling speed
Refer to “FUEL SYSTEM” in chapter 3.
4-22
FUEL
FUEL PUMP
E
FUEL PUMP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
FUEL PUMP DISASSEMBLY
Carburetors
Screw
Fuel pump cover
Gasket
Diaphragm
O-ring
Diaphragm body
Q’ty
4
1
1
1
1
1
4-23
Service points
Follow the left “Step” for disassembly.
Refer to “CARBURETOR”.
Not reusable
FUEL
FUEL PUMP
E
EXPLODED DIAGRAM
Step
7
8
9
10
Procedure/Part name
Rubber diaphragm
Diaphragm
Packing
Fuel filter
Q’ty
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
4-24
FUEL
FUEL PUMP
E
SERVICE POINTS
Fuel pump inspection
1. Inspect:
● Diaphragm
● Rubber diaphragm
● Diaphragm body
Damage → Replace.
Fuel filter inspection
1. Inspect:
● Fuel filter
Clog/contaminants → Clean.
Damage → Replace.
4-25
FUEL
OIL PUMP
E
OIL PUMP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
OIL PUMP REMOVAL
Exhaust chamber assembly
Intake duct
Oil pump cable
Oil delivery hose
Bolt
Bleed hose stay
Bolt
Q’ty
1
3
1
1
2
4-26
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY” in chapter 5.
Refer to “INTAKE DUCT AND SILENCER”.
FUEL
OIL PUMP
E
EXPLODED DIAGRAM
Step
6
7
8
9
Procedure/Part name
Oil pump assembly
Gasket
Oil hose 1
Oil hose 2
Q’ty
1
1
1
1
Service points
Not reusable
Reverse the removal steps for installation.
4-27
FUEL
OIL PUMP
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
OIL PUMP HOSES AND CABLE
REMOVAL
Bleed hose
Air bleed screw
Gasket
Bleed hose stay
Oil delivery hose 1
Oil delivery hose 2
Check valve
Oil pump cable
Q’ty
Service points
Follow the left “Step” for removal.
1
1
1
1
3
3
3
1
Reverse the removal steps for installation.
4-28
FUEL
OIL PUMP
E
SERVICE POINTS
Oil pump inspection
1. Inspect:
● Oil pump
Contaminants → Clean.
Damage/wear → Replace.
● Oil pump joint piece
Damage/wear → Replace.
Oil hose inspection
1. Inspect:
● Oil hose
Cracks/damage → Clean.
CAUTION:
● If
the oil delivery hoses are not full of oil,
fill them up.
● After installing the oil injection system,
bleed the system of any air.
Refer to “OIL INJECTION SYSTEM” in
chapter 3.
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
● Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
4-29
FUEL
OIL PUMP
E
Oil pump cable adjustment
1. Check:
● Oil pump lever position
Incorrect → Adjust.
Checking steps:
Fully close the carburetor throttle
valves.
● Check that the mark a on the oil pump
lever is aligned with the mark b on the
oil pump body.
●
2. Adjust:
● Oil pump cable
Adjustment steps:
● Loosen the locknut 1 and the adjusting nut 2.
● Fully close the carburetor throttle
valves.
● Adjust the oil pump cable so that the
mark a on the oil pump lever is
aligned with the mark b on the oil
pump body.
● Tighten the adjusting nut and locknut.
4-30
POWR
E
CHAPTER 5
POWER UNIT
EXHAUST CHAMBER ASSEMBLY ................................................................ 5-1
EXPLODED DIAGRAM ............................................................................. 5-1
REMOVAL AND INSTALLATION CHART ............................................... 5-1
MUFFLER ASSEMBLY ................................................................................... 5-4
EXPLODED DIAGRAM ............................................................................. 5-4
REMOVAL AND INSTALLATION CHART ............................................... 5-4
SERVICE POINT........................................................................................ 5-8
Catalyst inspection............................................................................ 5-8
EXHAUST MANIFOLD AND LEADS.............................................................. 5-9
EXPLODED DIAGRAM ............................................................................. 5-9
REMOVAL AND INSTALLATION CHART ............................................... 5-9
ENGINE UNIT ............................................................................................... 5-12
EXPLODED DIAGRAM ........................................................................... 5-12
REMOVAL AND INSTALLATION CHART ............................................. 5-12
SERVICE POINTS ................................................................................... 5-14
Shim removal .................................................................................. 5-14
Engine mount inspection ............................................................... 5-14
Coupling clearance inspection....................................................... 5-14
REED VALVES .............................................................................................. 5-15
EXPLODED DIAGRAM ........................................................................... 5-15
REMOVAL AND INSTALLATION CHART ............................................. 5-15
SERVICE POINTS ................................................................................... 5-17
Reed valve inspection..................................................................... 5-17
YPVS ............................................................................................................. 5-18
EXPLODED DIAGRAM ........................................................................... 5-18
REMOVAL AND INSTALLATION CHART ............................................. 5-18
SERVICE POINTS ................................................................................... 5-21
YPVS valve inspection .................................................................... 5-21
CYLINDER HEAD .......................................................................................... 5-22
EXPLODED DIAGRAM ........................................................................... 5-22
REMOVAL AND INSTALLATION CHART ............................................. 5-22
SERVICE POINTS ................................................................................... 5-24
Cylinder head inspection................................................................ 5-24
POWR
CYLINDERS ................................................................................................... 5-25
EXPLODED DIAGRAM ........................................................................... 5-25
REMOVAL AND INSTALLATION CHART ............................................. 5-25
SERVICE POINTS ................................................................................... 5-26
Cylinder inspection ......................................................................... 5-26
PISTONS ....................................................................................................... 5-27
EXPLODED DIAGRAM ........................................................................... 5-27
REMOVAL AND INSTALLATION CHART ............................................. 5-27
SERVICE POINTS ................................................................................... 5-29
Piston pin clip removal and installation........................................ 5-29
Piston inspection............................................................................. 5-29
Cylinder and piston combination .................................................. 5-30
Piston ring inspection ..................................................................... 5-30
Piston pin and bearing inspection ................................................. 5-31
GENERATOR AND STARTER MOTOR........................................................ 5-33
EXPLODED DIAGRAM ........................................................................... 5-33
REMOVAL AND INSTALLATION CHART ............................................. 5-33
SERVICE POINTS ................................................................................... 5-39
Drive coupling removal and installation ....................................... 5-39
Flywheel magneto removal and installation ................................ 5-39
Drive coupling inspection............................................................... 5-40
Flywheel magneto inspection ........................................................ 5-40
Starter clutch assembly inspection ............................................... 5-40
CRANKCASE................................................................................................. 5-41
EXPLODED DIAGRAM ........................................................................... 5-41
REMOVAL AND INSTALLATION CHART ............................................. 5-41
SERVICE POINTS ................................................................................... 5-43
Crankcase inspection ...................................................................... 5-43
Crankcase installation..................................................................... 5-43
CRANKSHAFT............................................................................................... 5-44
EXPLODED DIAGRAM ........................................................................... 5-44
REMOVAL AND INSTALLATION CHART ............................................. 5-44
SERVICE POINTS ................................................................................... 5-45
Crankshaft inspection ..................................................................... 5-45
E
1
2
3
4
5
6
7
8
9
POWR
EXHAUST CHAMBER ASSEMBLY
EXHAUST CHAMBER ASSEMBLY
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
EXHAUST CHAMBER
ASSEMBLY REMOVAL
Exhaust temperature sensor
coupler
Cap/bolt
Cover
Clamp/hose
Hose clamp
Hose clamp
Bolt
Bolt
Q’ty
1
3/3
1
4/4
2
2
2
2
5-1
Service points
Follow the left “Step” for removal.
E
POWR
EXHAUST CHAMBER ASSEMBLY
E
EXPLODED DIAGRAM
Step
9
10
11
12
13
14
15
16
17
Procedure/Part name
Exhaust chamber stay
Bolt
Bolt
Exhaust chamber assembly
Clamp/hose
Gasket
Pin
Outer exhaust joint
Inner exhaust joint
Q’ty
1
3
1
1
1/1
1
2
1
1
Service points
Not reusable
Reverse the removal steps for installation.
5-2
POWR
EXHAUST CHAMBER ASSEMBLY
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
EXHAUST CHAMBER
DISASSEMBLY
Bolt
Bolt
Exhaust chamber joint
Gasket
Pin
Exhaust chamber
Q’ty
5
1
1
1
2
1
Service points
Follow the left “Step” for disassembly.
Not reusable
Reverse the disassembly steps for
assembly.
5-3
POWR
MUFFLER ASSEMBLY
E
MUFFLER ASSEMBLY
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
MUFFLER ASSEMBLY REMOVAL
Exhaust chamber assembly
Cylinder head
Band
Ventilation hose
Screw
Ventilation duct
Water temperature sensor
coupler
Clamp/hose
Q’ty
1
1
4
1
1
1/1
5-4
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
Refer to “CYLINDER HEAD”.
POWR
MUFFLER ASSEMBLY
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
15
Procedure/Part name
Hose clamp
Water lock band
Bolt
Gear case grease hose
Bolt
Bolt
Bolt
Muffler stay 2
Muffler assembly
Q’ty
1
1
Service points
Slide the water lock toward back to
disconnect the muffler assembly.
4
1
2
2
1
1
1
Reverse the removal steps for installation.
5-5
POWR
MUFFLER ASSEMBLY
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
MUFFLER DISASSEMBLY
Exhaust temperature sensor
Water temperature sensor
Nut
Hanger
Bolt
Muffler stay
Bolt
Cover
Gasket
Q’ty
1
1
2
2
2
1
6
1
1
5-6
Service points
Follow the left “Step” for disassembly.
Not reusable
POWR
MUFFLER ASSEMBLY
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
16
17
18
Procedure/Part name
Catalyst housing
Gasket
Catalyst
Gasket
Pin
Bolt
Mixing joint
Gasket
Muffler
Q’ty
1
1
1
1
2
6
1
1
1
Service points
Not reusable
Not reusable
Not reusable
Reverse the disassembly steps for
assembly.
5-7
POWR
MUFFLER ASSEMBLY
E
SERVICE POINT
Catalyst inspection
1. Inspect:
● Catalyst
Cracks/damage → Replace.
5-8
POWR
EXHAUST MANIFOLD AND LEADS
E
EXHAUST MANIFOLD AND LEADS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
EXHAUST MANIFOLD AND
LEADS REMOVAL
Battery lead
(negative and positive)
Exhaust chamber assembly
Q’ty
AC magneto coupler
Bolt
YPVS cable holder
YPVS cable
Clamp/hose
1
2
1
2
1/1
Service points
Follow the left “Step” for removal.
Refer to “ELECTRICAL BOX” in chapter 7.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
5-9
POWR
EXHAUST MANIFOLD AND LEADS
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
11
12
13
14
15
Procedure/Part name
Bolt
Bolt
Nut
Exhaust manifold
Gasket
Pin
Bolt
Battery negative lead
Nut/washer
Starter motor lead
Q’ty
4
6
2
1
1
2
1
1
1/1
1
Service points
Not reusable
Reverse the removal steps for installation.
5-10
POWR
EXHAUST MANIFOLD AND LEADS
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
EXHAUST MANIFOLD
DISASSEMBLY
Clamp/hose
Bolt
Joint pipe
O-ring
Exhaust manifold
Q’ty
Service points
Follow the left “Step” for disassembly.
1/1
6
1
3
1
Reverse the disassembly steps for
assembly.
5-11
POWR
ENGINE UNIT
E
ENGINE UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
Procedure/Part name
ENGINE UNIT REMOVAL
Exhaust chamber assembly
Muffler assembly
Carburetor
Oil pump
Spark plug lead
Bolt
Collar
Q’ty
3
1
1
5-12
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
Refer to “MUFFLER ASSEMBLY”.
Refer to “CARBURETOR” in chapter 4.
Refer to “OIL PUMP” in chapter 4.
POWR
ENGINE UNIT
E
EXPLODED DIAGRAM
Step
4
5
6
7
Procedure/Part name
Coupling cover
Bolt/washer
Engine assembly
Shim
Q’ty
1
4/4
1
*
*: As required
5-13
Service points
Install the shims original position.
Reverse the removal steps for installation.
POWR
ENGINE UNIT
E
SERVICE POINTS
Shim removal
1. Remove:
● Shims
NOTE:
To ease reassembly and coupling alignment, remove the shims and organize them
in their respective groups (e.g., front right,
rear left) prior to removing the mounting
bolts.
Engine mount inspection
1. Inspect:
● Engine mounts
Cracks/damage → Replace.
Coupling clearance inspection
1. Measure:
● Clearance a
● Clearance b
(with a straightedge and thickness
gauge)
Out of specification → Adjust with the
shims.
NOTE:
Before measuring the clearance, remove
the rubber damper.
Clearance a:
0 ~ 1.0 mm (0 ~ 0.039 in)
Clearance b:
2 ~ 4 mm (0.079 ~ 0.157 in)
5-14
POWR
REED VALVES
E
REED VALVES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
REED VALVE REMOVAL
Exhaust chamber assembly
Q’ty
Muffler assembly
Carburetor unit
1
2
Bolt
Reed valve plate
18
1
5-15
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
Refer to “MUFFLER ASSEMBLY”.
Refer to “CARBURETOR UNIT” in
chapter 4.
NOTE:
Tighten the bolts in the proper sequence
as shown.
POWR
REED VALVES
E
EXPLODED DIAGRAM
Step
3
4
5
6
Procedure/Part name
Reed valve assembly
Screw
Valve stopper
Reed valve
Q’ty
3
24
6
6
Service points
Reverse the removal steps for installation.
5-16
POWR
REED VALVES
E
SERVICE POINTS
Reed valve inspection
1. Inspect:
● Reed valves
Cracks/damage → Replace.
2. Measure:
● Valve bending a
Out of specification → Replace.
Max. valve bending:
0.2 mm (0.01 in)
3. Measure:
● Valve stopper height b
Out of specification → Adjust or
replace.
Valve stopper height:
10.4 ~ 11.0 mm (0.41 ~ 0.43 in)
5-17
POWR
YPVS
E
YPVS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
YPVS REMOVAL
YPVS cable 1 and 2
Q’ty
Exhaust chamber assembly
1
2
3
4
5
6
Bolt
YPVS cable bracket
YPVS valve cover
Gasket
Spacer
Link joint/cover
12
1
3
3
2
2/2
5-18
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST MANIFOLD AND
LEADS”.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
Not reusable
POWR
YPVS
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
Procedure/Part name
Bolt (M4)
Circlip
Shaft 3
Shaft 2
Shaft 1
Washer
YPVS valve lever
Q’ty
3
5
1
1
1
5
3
5-19
Service points
NOTE:
During installation, align the hole a in
the YPVS shaft with the screw.
Not reusable
POWR
YPVS
E
EXPLODED DIAGRAM
Step
14
15
16
Procedure/Part name
Bolt (M5)
YPVS valve assembly
Oil seal
Q’ty
3
3
6
Service points
NOTE:
If the YPVS shaft is removed, the oil seal
must be replaced.
Reverse the removal steps for installation.
5-20
POWR
YPVS
E
SERVICE POINTS
YPVS valve inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
CAUTION:
Do not use a sharp instrument to avoid
damaging or scratching the surfaces.
2. Inspect:
● YPVS valve assembly
Crack/damage/wear → Replace.
5-21
POWR
CYLINDER HEAD
E
CYLINDER HEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
CYLINDER HEAD REMOVAL
Exhaust chamber assembly
Spark plug
Bolt
Bolt
Bolt
Bolt
Q’ty
3
2
2
6
16
5-22
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
NOTE:
Tighten the bolts in the proper sequence
as shown and in three stages. (No. 23, 24
in two stages)
POWR
CYLINDER HEAD
E
EXPLODED DIAGRAM
Step
6
7
8
9
Procedure/Part name
Cylinder head cover
Gasket
Cylinder head
Gasket
Q’ty
1
1
1
1
5-23
Service points
Not reusable
Not reusable
Reverse the removal steps for installation.
POWR
CYLINDER HEAD
E
SERVICE POINTS
Cylinder head inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
CAUTION:
Do not use a sharp instrument to avoid
damaging or scratching the cylinder head
or spark plug bore threads.
2. Inspect:
● Cylinder head water jacket
Corrosion/mineral deposits → Clean
or replace.
3. Measure:
● Cylinder head warpage
(with a straightedge and thickness
gauge)
Out of specification/score marks →
Resurface.
Warpage limit:
0.1 mm (0.004 in)
NOTE:
Place a 400 ~ 600 grit wet sandpaper on a
surface plate and resurface the cylinder
head using a figure-eight sanding pattern.
5-24
POWR
CYLINDERS
E
CYLINDERS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
Procedure/Part name
CYLINDER REMOVAL
YPVS
Cylinder head
Bolt
Q’ty
2
Cylinder
3
NOTE:
Install the original position.
3
4
Cylinder gasket
Pin
3
6
Not reusable
12
Service points
Follow the left “Step” for removal.
Refer to “YPVS”.
Refer to “CYLINDER HEAD”.
NOTE:
Tighten the bolts in a crisscross pattern
and in two stages.
Reverse the removal steps for installation.
5-25
POWR
CYLINDERS
E
SERVICE POINTS
Cylinder inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
2. Inspect:
● Cylinder water jacket
Corrosion/mineral deposits → Clean
or replace.
● Cylinder inner surface
Score marks → Replace.
3. Measure:
● Cylinder bore “D”
(with a cylinder gauge)
Out of specification → Replace cylinder and piston as a set.
NOTE:
Measure the cylinder bore in parallel and at
a right angle to the crankshaft. Then, average the measurements.
Standard
Limit
Cylinder
bore “D”
80.000 ~
80.018 mm
(3.1496 ~
3.1503 in)
Original cylinder
bore + 0.04 mm
(0.0016 in)
Taper “T”
—
0.08 mm
(0.003 in)
Out of
round “R”
—
0.05 mm
(0.002 in)
D = Maximum (D1 ~ D6)
T = (Maximum D1 or D2) – (Maximum D5
or D6)
R = (Maximum D1, D3 or D5) – (Minimum
D2, D4 or D6)
5-26
POWR
PISTONS
E
PISTONS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
Procedure/Part name
PISTON REMOVAL
Cylinders
Piston pin clip
Q’ty
6
Service points
Follow the left “Step” for removal.
Refer to “CYLINDERS”.
CAUTION:
Do not align the open end of the clip with
the piston pin slot a.
2
3
4
Piston pin
Piston
Washer
3
3
6
5-27
NOTE:
Make sure that the arrow b faces
towards the exhaust side.
POWR
PISTONS
E
EXPLODED DIAGRAM
Step
5
6
Procedure/Part name
Bearing
Piston ring
Q’ty
3
6
Service points
CAUTION:
Align each end gap with its respective
locating pin.
Reverse the removal steps for installation.
5-28
POWR
PISTONS
E
SERVICE POINTS
Piston pin clip removal and installation
1. Remove and install:
● Piston pin clip
NOTE:
Before removing or installing the piston pin
clip, cover the crankcase opening with a
clean rag to prevent the piston pin clip from
falling into the crankcase.
Piston inspection
1. Eliminate:
● Carbon deposits
(from the piston crown and piston
ring grooves)
2. Inspect:
● Piston wall
Score marks → Repair with 600 ~ 800
grit wet sandpaper or replace.
NOTE:
Lightly sand the piston wall in a crisscross
pattern.
3. Measure:
● Piston skirt diameter
(with a micrometer)
Out of specification → Replace.
Piston diameter
79.899 ~ 79.914 mm
(3.1456 ~ 3.1462 in)
5-29
Distance a
22 mm
(0.87 in)
POWR
PISTONS
E
4. Calculate:
● Piston-to-cylinder clearance
Out of specification → Replace the
piston, piston rings and cylinder as a
set.
PISTON
CYLINDER
PISTON
=
–
CLEARANCE
BORE
DIAMETER
Piston-to-cylinder clearance:
0.100 ~ 0.105 mm
(0.0039 ~ 0.0041 in)
Cylinder and piston combination
Select the appropriate piston to match the
cylinder size by the table as follows.
Cylinder size
indication a
Piston color mark
0~5
Red
6 ~ 10
Orange
11 ~ 15
Green
16 ~ 18
Purple
NOTE:
New cylinder bore size = 80.000 + a/1,000
Example: a = 12 → 80.012 mm.
Piston ring inspection
1. Measure:
● Side clearance
(with a thickness gauge 1)
Out of specification → Replace the
piston and piston rings as a set.
Side clearance:
0.02 ~ 0.07 mm (0.001 ~ 0.003 in)
5-30
POWR
PISTONS
E
2. Measure:
● End gap
(with a thickness gauge 1)
Out of specification → Replace the
piston rings as a set.
End gap:
0.45 ~ 0.60 mm (0.018 ~ 0.024 in)
NOTE:
Push the piston ring into the cylinder with
the piston crown.
Piston pin and bearing inspection
1. Inspect:
● Piston pins
● Bearings
Signs of heat discoloration → Replace.
2. Measure:
● Piston pin outside diameter
(with a micrometer 1)
Out of specification → Replace.
Piston pin outside diameter:
Standard
21.995 ~ 22.000 mm
(0.8659 ~ 0.8661 in)
Limit
21.990 mm (0.8657 in)
3. Check:
● Piston-pin-to-piston free play
(with the piston pin in the piston as
shown)
Free play → Replace the piston pin,
piston or both.
5-31
POWR
PISTONS
E
4. Check:
● Piston-pin-to-connecting-rod free play
(with the piston pin in the small end
of the connecting rod as shown)
Free play/small end wear → Replace
the piston pin, connecting rod or
both.
5-32
POWR
GENERATOR AND STARTER MOTOR
GENERATOR AND STARTER MOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
GENERATOR COVER REMOVAL
Engine unit
Oil pump
Band
Bolt
Bolt
Ground lead
Generator cover
Washer
Q’ty
1
1
7
1
1
2
5-33
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT”.
Refer to “OIL PUMP” in chapter 4.
E
POWR
GENERATOR AND STARTER MOTOR
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
Procedure/Part name
Spring
Packing
Pin
Bolt
Bolt
Bracket
Q’ty
1
1
2
2
2
1
Service points
Reverse the removal steps for installation.
5-34
POWR
GENERATOR AND STARTER MOTOR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
STATOR COIL AND PICKUP COIL
REMOVAL
Bolt
Washer
Cable holder
Bolt
Pickup coil
Bolt
Stator coil
Q’ty
3
1
1
2
1
3
1
Service points
Follow the left “Step” for removal.
NOTE:
This washer holds the pickup coil lead.
Make sure to not pinch the lead between
the projection and the washer when
installing the bolt.
Reverse the removal steps for installation.
5-35
POWR
GENERATOR AND STARTER MOTOR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
GENERATOR ROTOR AND
STARTER MOTOR REMOVAL
Drive coupling
Flywheel magneto bolt
Flywheel magneto
Woodruff key
Starter clutch assembly
Bolt
Starter motor
Q’ty
Service points
Follow the left “Step” for removal.
1
1
1
1
1
2
1
Reverse the removal steps for installation.
5-36
POWR
GENERATOR AND STARTER MOTOR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
STARTER CLUTCH
DISASSEMBLY
Clip
Clip stopper
Spring seat
Spring
Idle gear
Circlip
Plate
Q’ty
1
1
1
1
1
1
1
5-37
Service points
Follow the left “Step” for disassembly.
Not reusable
POWR
GENERATOR AND STARTER MOTOR
EXPLODED DIAGRAM
Step
8
9
10
Procedure/Part name
Weight
Spring
Pinion gear
Q’ty
3
1
1
Service points
Reverse the disassembly steps for
assembly.
5-38
E
POWR
GENERATOR AND STARTER MOTOR
E
SERVICE POINTS
Drive coupling removal and installation
1. Remove:
● Drive coupling
Coupler wrench:
YW-06551/90890-06551
Flywheel holder:
YW-06550/90890-06550
NOTE:
Install the drive coupling with the same
special tools that were used for removal.
Flywheel magneto removal and installation
1. Remove:
● Flywheel magneto bolt
Flywheel holder:
YW-06550/90890-06550
NOTE:
Install the bolt with the same special tool
that was used for removal.
Å
2. Remove:
● Generator rotor
Flywheel puller:
YB-06117/90890-06521
Set bolt:
M8 × 60 mm
Å For USA and CANADA
ı For worldwide
ı
CAUTION:
To prevent damage to the engine or tools,
screw in the flywheel puller set bolts
evenly and completely so that the puller
plate is parallel to the generator rotor.
5-39
POWR
GENERATOR AND STARTER MOTOR
Drive coupling inspection
1. Inspect:
● Drive coupling
Damage/wear → Replace.
Flywheel magneto inspection
1. Inspect:
● Ring gear
Damage/wear → Replace.
Starter clutch assembly inspection
1. Inspect:
● Pinion gear 1
● Idle gear 2
Damage/wear → Replace.
2. Check:
● Gear movement
Rough movement → Replace the
defective part(s).
5-40
E
POWR
CRANKCASE
E
CRANKCASE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
CRANKCASE DISASSEMBLY
Pistons
Generator cover and starter
motor
Bolt
Mount bracket
Pin
Bolt
Bolt
Bolt
Q’ty
6
2
4
3
1
6
5-41
Service points
Follow the left “Step” for disassembly.
Refer to “PISTONS”.
Refer to “GENERATOR AND STARTER
MOTOR”.
POWR
CRANKCASE
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
Procedure/Part name
Bolt
Bolt
Bolt
Lower crankcase
Pin
Crankshaft assembly
Upper crankcase
Q’ty
1
12
4
1
2
1
1
Service points
NOTE:
Tighten the bolts in sequence as shown.
Reverse the disassembly steps for
assembly.
5-42
POWR
CRANKCASE
E
SERVICE POINTS
Crankcase inspection
1. Inspect:
● Mating surfaces
Scratches → Replace the crankcase.
● Crankcase
Cracks/damage → Replace.
Crankcase installation
1. Apply:
● Gasket Maker
(onto the crankcase mating surfaces)
NOTE:
Before applying Gasket Maker, clean the
crankcase mating surfaces.
2. Check:
● Crankshaft
Rough movement → Recheck.
NOTE:
After installation, make sure that the crankshaft rotates smoothly.
5-43
POWR
CRANKSHAFT
E
CRANKSHAFT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
CRANKSHAFT REMOVAL
Crankcase
Oil seal
Bearing
Oil seal
Crankshaft assembly
Q’ty
1
1
2
1
Service points
Follow the left “Step” for removal.
Refer to “CRANKCASE”.
CAUTION:
Install the bearing locating pins into the
grooves in the crankcase body.
Reverse the removal steps for installation.
5-44
POWR
CRANKSHAFT
E
SERVICE POINTS
Crankshaft inspection
1. Measure:
● Crank width A
Out of specification → Replace.
Crank width:
72.95 ~ 73.00 mm
(2.872 ~ 2.835 in)
2. Measure:
● Deflection B
(with a dial gauge)
Out of specification → Replace.
Max. deflection:
B 0.05 mm (0.002 in)
C 0.15 mm (0.006 in)
3. Measure:
● Big end side clearance D
(with a thickness gauge)
Out of specification → Replace.
Big end side clearance:
0.25 ~ 0.75 mm (0.010 ~ 0.030 in)
4. Measure:
● Small end free play E
(with a dial gauge)
Out of specification → Replace.
Small end free play:
2.0 mm (0.08 in)
5-45
POWR
CRANKSHAFT
E
5. Inspect:
● Bearings
Damage/pitting → Replace.
NOTE:
● Before inspection, thoroughly clean the
bearings.
● Immediately after inspection, lubricate the
bearings to prevent rust.
6. Inspect:
● Oil seals
Damage/wear → Replace.
5-46
JET
PUMP
E
CHAPTER 6
JET PUMP UNIT
JET PUMP UNIT ............................................................................................. 6-1
EXPLODED DIAGRAM ............................................................................. 6-1
REMOVAL AND INSTALLATION CHART ............................................... 6-1
REVERSE GATE.............................................................................................. 6-3
EXPLODED DIAGRAM ............................................................................. 6-3
REMOVAL AND INSTALLATION CHART ............................................... 6-3
NOZZLE DEFLECTOR AND NOZZLE RING................................................... 6-6
EXPLODED DIAGRAM ............................................................................. 6-6
REMOVAL AND INSTALLATION CHART ............................................... 6-6
IMPELLER DUCT, IMPELLER HOUSING, AND INTAKE DUCT.................... 6-7
EXPLODED DIAGRAM ............................................................................. 6-7
REMOVAL AND INSTALLATION CHART ............................................... 6-7
IMPELLER DUCT AND DRIVE SHAFT........................................................... 6-9
EXPLODED DIAGRAM ............................................................................. 6-9
REMOVAL AND INSTALLATION CHART ............................................... 6-9
SERVICE POINTS ................................................................................... 6-11
Drive shaft removal......................................................................... 6-11
Impeller inspection ......................................................................... 6-11
Drive shaft inspection ..................................................................... 6-11
Bearing inspection .......................................................................... 6-11
Drive shaft installation.................................................................... 6-12
TRANSOM PLATE AND HOSES.................................................................. 6-13
EXPLODED DIAGRAM ........................................................................... 6-13
REMOVAL AND INSTALLATION CHART ............................................. 6-13
SERVICE POINTS ................................................................................... 6-14
Bilge strainer inspection................................................................. 6-14
Bilge hose inspection...................................................................... 6-14
JET
PUMP
BEARING HOUSING..................................................................................... 6-15
EXPLODED DIAGRAM ........................................................................... 6-15
REMOVAL AND INSTALLATION CHART ............................................. 6-15
SERVICE POINTS ................................................................................... 6-18
Driven coupling removal and installation..................................... 6-18
Driven coupling shaft removal....................................................... 6-18
Bearing removal.............................................................................. 6-18
Bearing, driven coupling shaft, and grease hose inspection ...... 6-19
Driven coupling inspection ............................................................ 6-19
Bearing installation ......................................................................... 6-19
Oil seal installation.......................................................................... 6-19
Bearing housing installation .......................................................... 6-20
E
1
2
3
4
5
6
7
8
9
JET
PUMP
JET PUMP UNIT
E
JET PUMP UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
10
11
Procedure/Part name
JET PUMP UNIT REMOVAL
Bolt
Bolt
Intake screen
Bolt
Intake duct
Screw
Speed sensor
Bolt
Jet pump cover
Shift cable joint
QSTS cable joint
Q’ty
2
2
1
4
1
4
1
4
1
1
1
6-1
Service points
Follow the left “Step” for removal.
JET
PUMP
JET PUMP UNIT
E
EXPLODED DIAGRAM
Step
12
13
14
15
16
17
18
19
Procedure/Part name
Clamp/bilge hose
Nut/washer
Steering cable joint
Clamp/spout hose
Bolt
Bolt
Jet pump unit assembly
Dowel pin
Q’ty
1/1
1/2
1
1/1
1
4
1
2
Service points
NOTE:
● Pull the jet pump unit straight back.
● When installing the jet pump unit, align
the drive shaft spline (male) with the
intermediate shaft spline (female).
Reverse the removal steps for installation.
6-2
JET
PUMP
REVERSE GATE
E
REVERSE GATE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
REVERSE GATE REMOVAL
Clamp/spout hose
Bolt
Washer
Collar
Reverse gate assembly
Nut
Bolt
Washer
Q’ty
1/1
2
2
2
1
1
1
2
6-3
Service points
Follow the left “Step” for removal.
JET
PUMP
REVERSE GATE
E
EXPLODED DIAGRAM
Step
9
10
11
12
13
14
15
16
17
Procedure/Part name
Roller
Bolt
Reverse gate stay
Nut
Washer
Bolt
Lever
Spacer
Nut
Q’ty
1
6
2
1
1
1
1
1
1
6-4
Service points
JET
PUMP
REVERSE GATE
E
EXPLODED DIAGRAM
Step
18
19
20
21
22
23
Procedure/Part name
Washer
Collar
Spring
Lever
Bolt
Washer
Q’ty
1
1
1
1
1
2
Service points
Reverse the removal steps for installation.
6-5
JET
PUMP
NOZZLE DEFLECTOR AND NOZZLE RING
E
NOZZLE DEFLECTOR AND NOZZLE RING
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
NOZZLE DEFLECTOR AND
NOZZLE RING REMOVAL
Jet pump unit
Reverse gate
Bolt/washer
Spacer
Nozzle deflector
Bolt/washer
Spacer
Nozzle ring
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “JET PUMP UNIT”.
Refer to “REVERSE GATE”.
2/2
2
1
2/2
2
1
Reverse the removal steps for installation.
6-6
JET
PUMP
IMPELLER DUCT, IMPELLER HOUSING,
AND INTAKE DUCT
E
IMPELLER DUCT, IMPELLER HOUSING, AND INTAKE DUCT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
IMPELLER DUCT AND IMPELLER
HOUSING REMOVAL
Nozzle ring
Bolt
Nozzle
Pin
Impeller duct assembly
Pin
Impeller housing
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “NOZZLE DEFLECTOR AND
NOZZLE RING”.
4
1
2
1
2
1
6-7
NOTE:
Clean the contacting surfaces before
applying the Gasket Maker.
IMPELLER DUCT, IMPELLER HOUSING,
AND INTAKE DUCT
JET
PUMP
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
Procedure/Part name
Bolt
Cover
Packing
Filter
Packing
Q’ty
4
1
1
1
1
Service points
Reverse the removal steps for installation.
6-8
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
IMPELLER DUCT AND DRIVE SHAFT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
*1:
Procedure/Part name
IMPELLER DUCT AND DRIVE
SHAFT DISASSEMBLY
Impeller
Spacer
Bolt/washer
Cap
O-ring
Nut
Washer
Q’ty
Service points
Follow the left “Step” for disassembly.
1
1
3/3
1
1
1
1
Left-hand threads
EPNOC grease AP #0
6-9
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
Procedure/Part name
Drive shaft
Rear bearing
Spacer
Front bearing
Oil seal
Oil seal
Q’ty
1
1
1
1
1
1
Service points
Not reusable
Not reusable
Reverse the disassembly steps for
assembly.
*1:
EPNOC grease AP #0
6-10
E
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
SERVICE POINTS
Drive shaft removal
1. Remove:
● Impeller
Drive shaft holder:
YB-06151/90890-06519
NOTE:
The impeller has left-hand threads. Turn the
impeller clockwise to loosen it.
2. Remove:
● Nut 1
Drive shaft holder:
YB-06151/90890-06519
3. Remove:
● Drive shaft 1
NOTE:
Remove the drive shaft with a press.
4. Remove:
● Rear bearing
● Front bearing
Slide hammer set:
90890-06523
YB-06096/90890-06531
Impeller inspection
Refer to “JET
chapter 3.
PUMP
UNIT”
Drive shaft inspection
1. Inspect:
● Drive shaft
Damage/wear → Replace.
Bearing inspection
1. Inspect:
● Front and rear bearings
(rotate each inner race by hand)
Damage/rough movement →
Replace.
6-11
in
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
Drive shaft installation
1. Install:
● Oil seal
Driver rod:
YB-06071/90890-06606
Ball bearing attachment:
YB-06156/90890-06634
2. Install:
● Front bearing
● Drive shaft
NOTE:
Install the front bearing and drive shaft with
a press.
Distance a:
23 ± 0.1 mm (0.91 ± 0.004 in)
3. Add:
● EPNOC grease AP #0
(between the drive shaft and spacer)
Quantity:
Approximately 1/3 of capacity
4. Install:
● Rear bearing
Bearing inner race attachment:
YB-34474/90890-06662
5. Add:
● EPNOC grease AP #0 (into the cap)
Quantity:
Approximately 1/3 of capacity
6. Install:
● Nut
● Impeller
Drive shaft holder:
YB-06151/90890-06519
6-12
JET
PUMP
TRANSOM PLATE AND HOSES
E
TRANSOM PLATE AND HOSES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
TRANSOM PLATE AND HOSES
REMOVAL
Hose clamp
Hose
Bilge hose 1
Hose
Nut/washer
Transom plate
Clamp/bilge hose 2
Holder
Bilge filter
Q’ty
3
1
1
1
4/4
1
1/1
1
1
Service points
Follow the left “Step” for removal.
Cooling water outlet
Cooling water inlet
Reverse the removal steps for installation.
6-13
JET
PUMP
TRANSOM PLATE AND HOSES
SERVICE POINTS
Bilge strainer inspection
Refer to “JET PUMP UNIT” in
chapter 3.
Bilge hose inspection
1. Inspect:
● Bilge hose
Cracks/damage/wear → Replace.
6-14
E
JET
PUMP
BEARING HOUSING
E
BEARING HOUSING
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
BEARING HOUSING REMOVAL
Engine unit
Rubber coupling
Bolt/washer
Bearing housing assembly
Pin
Shim
Q’ty
1
3/3
1
2
*
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
NOTE:
Install the shims in their original locations.
Reverse the removal steps for installation.
*: As required
6-15
JET
PUMP
BEARING HOUSING
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
BEARING HOUSING
DISASSEMBLY
Grease hose
Grease nipple
Grease nipple stay
Nipple
Driven coupling
Washer
Driven coupling shaft
Q’ty
1
1
1
2
1
1
1
6-16
Service points
Follow the left “Step” for disassembly.
JET
PUMP
BEARING HOUSING
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
Procedure/Part name
O-ring
Oil seal
Oil seal
Circlip
Bearing
Circlip
Q’ty
2
2
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
6-17
JET
PUMP
BEARING HOUSING
E
SERVICE POINTS
Driven coupling removal and installation
1. Remove and install:
● Driven coupling
Coupler wrench:
YW-06551/90890-06551
Shaft holder:
YB-06552/90890-06552
NOTE:
Install the driven coupling with the same
special tools that were used for removal.
Driven coupling shaft removal
1. Remove:
● Driven coupling shaft
Removal steps:
Temporarily install the driven coupling
to the driven coupling shaft.
● Insert the long rod to the driven coupling shaft.
● Press out the driven coupling shaft by
pushing the rod.
●
Bearing removal
1. Remove:
● Bearing
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
NOTE:
Install the bearing with the same special
tools that were used for removal.
6-18
JET
PUMP
BEARING HOUSING
E
Bearing, driven coupling shaft, and grease
hose inspection
1. Inspect:
● Bearing
Rotate the inner race by hand.
Damage/rough movement →
Replace.
● Driven coupling shaft
Damage/pitting → Replace.
● Grease hose
Cracks/wear → Replace.
Driven coupling inspection
1. Inspect:
● Driven coupling
● Driven coupling damper
Damage/wear → Replace.
Bearing installation
1. Install:
● Bearing
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
Oil seal installation
1. Install:
● Oil seal
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
NOTE:
Before installing the oil seal, lubricate the
clip groove with water resistant grease.
Distance a:
6.8 ~ 7.2 mm (0.27 ~ 0.28 in)
6-19
JET
PUMP
BEARING HOUSING
E
2. Install:
● Driven coupling shaft
Distance a:
9.5 ~ 10.5 mm (0.37 ~ 0.41 in)
3. Install:
● Oil seal 1 [8 mm (0.31 in)]
● Oil seal 2 [10 mm (0.39 in)]
Distance a:
10.3 ~ 10.7 mm (0.41 ~ 0.42 in)
Distance b:
1.6 ~ 2.0 mm (0.06 ~ 0.07 in)
Bearing housing installation
1. Install:
● Bearing housing
● Shim
Installation steps:
Install the bearing housing.
● Measure the clearance a at each bolt
hole.
● Install the suitable shim from the table
below.
●
Clearance a
Shim thickness
0 ~ 0.2 mm
(0 ~ 0.010 in)
No need
0.3 ~ 0.7 mm
(0.011 ~ 0.030 in)
0.5 mm
0.8 ~ 1.2 mm
(0.031 ~ 0.050 in)
1.0 mm
1.3 ~ 2.0 mm
(0.051 ~ 0.078 in)
1.5 mm
NOTE:
Install the shim(s) to the original position if
the bearing housing is not replaced.
6-20
ELEC
–
+
E
CHAPTER 7
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS......................................................................... 7-1
ELECTRICAL BOX ........................................................................................... 7-2
EXPLODED DIAGRAM ............................................................................. 7-2
REMOVAL AND INSTALLATION CHART ............................................... 7-2
ELECTRICAL ANALYSIS ................................................................................ 7-8
INSPECTION............................................................................................. 7-8
Digital circuit tester ........................................................................... 7-8
Low resistance measurement .......................................................... 7-9
Peak voltage measurement.............................................................. 7-9
Peak voltage adaptor ........................................................................ 7-9
Test harness .................................................................................... 7-10
IGNITION SYSTEM....................................................................................... 7-11
WIRING DIAGRAM................................................................................. 7-11
IGNITION SPARK GAP........................................................................... 7-12
IGNITION SYSTEM PEAK VOLTAGE.................................................... 7-13
BATTERY ................................................................................................ 7-15
FUSE ....................................................................................................... 7-15
SPARK PLUGS ....................................................................................... 7-15
SPARK PLUG LEAD ASSEMBLY........................................................... 7-15
IGNITION COIL ....................................................................................... 7-15
ENGINE STOP SWITCH ......................................................................... 7-16
WATER TEMPERATURE SENSOR........................................................ 7-16
EXHAUST TEMPERATURE SENSOR ................................................... 7-17
STARTING SYSTEM..................................................................................... 7-18
WIRING DIAGRAM................................................................................. 7-18
BATTERY ................................................................................................ 7-19
WIRING CONNECTIONS ....................................................................... 7-19
FUSE ....................................................................................................... 7-19
STARTER SWITCH ................................................................................. 7-20
STARTER RELAY.................................................................................... 7-20
STARTER MOTOR ........................................................................................ 7-21
EXPLODED DIAGRAM ........................................................................... 7-21
REMOVAL AND INSTALLATION CHART ............................................. 7-21
SERVICE POINTS ................................................................................... 7-24
Armature inspection ....................................................................... 7-24
Brush holder inspection ................................................................. 7-25
Starter motor front cover inspection............................................. 7-25
ELEC
–
+
CHARGING SYSTEM.................................................................................... 7-26
WIRING DIAGRAM................................................................................. 7-26
FUSE ....................................................................................................... 7-27
BATTERY ................................................................................................ 7-27
LIGHTING COIL ...................................................................................... 7-27
RECTIFIER/REGULATOR........................................................................ 7-27
YPVS ............................................................................................................. 7-28
WIRING DIAGRAM................................................................................. 7-28
FUSE ....................................................................................................... 7-29
BATTERY ................................................................................................ 7-29
PICKUP COIL .......................................................................................... 7-29
CDI UNIT................................................................................................. 7-29
LIGHTING COIL ...................................................................................... 7-29
RECTIFIER/REGULATOR........................................................................ 7-29
YPVS SERVOMOTOR .................................................................................. 7-30
EXPLODED DIAGRAM ........................................................................... 7-30
REMOVAL AND INSTALLATION CHART ............................................. 7-30
SERVICE POINTS ................................................................................... 7-31
YPVS cable removal and installation ............................................ 7-31
YPVS cable inspection .................................................................... 7-31
YPVS servomotor inspection ......................................................... 7-31
YPVS cable adjustment .................................................................. 7-32
INDICATION SYSTEM.................................................................................. 7-33
WIRING DIAGRAM................................................................................. 7-33
FUSE ....................................................................................................... 7-34
BATTERY ................................................................................................ 7-34
LIGHTING COIL ...................................................................................... 7-34
RECTIFIER/REGULATOR........................................................................ 7-34
CDI UNIT................................................................................................. 7-34
WATER TEMPERATURE SENSOR........................................................ 7-34
EXHAUST TEMPERATURE SENSOR ................................................... 7-34
BUZZER .................................................................................................. 7-34
OIL LEVEL SENSOR ............................................................................... 7-34
FUEL LEVEL SENSOR............................................................................ 7-35
MULTI-FUNCTION METER.................................................................... 7-35
Multi-function meter ....................................................................... 7-35
EXPLODED DIAGRAM ........................................................................... 7-36
REMOVAL AND INSTALLATION CHART ............................................. 7-36
Display function .............................................................................. 7-37
Fuel level gauge .............................................................................. 7-39
Oil level gauge................................................................................. 7-40
Overheat warning indicator ........................................................... 7-41
Speed meter .................................................................................... 7-43
Speed sensor................................................................................... 7-44
E
1
2
3
4
5
6
7
8
9
ELEC
–
+
ELECTRICAL COMPONENTS
ELECTRICAL COMPONENTS
1
2
3
4
5
6
7
8
YPVS servomotor
Multi-function meter
Fuel level sensor
Buzzer
Oil level sensor
Stator coil and pickup coil
Spark plugs
Exhaust temperature sensor
9
0
A
B
C
D
7-1
Battery
Speed sensor
Electrical box
Water temperature sensor
Starter motor
Engine stop switch, engine stop lanyard
switch and starter switch
E
ELEC
–
+
ELECTRICAL BOX
E
ELECTRICAL BOX
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
ELECTRICAL BOX REMOVAL
Exhaust chamber assembly
Q’ty
Exhaust manifold
1
2
3
4
5
Spark plug lead
Battery negative lead
Battery positive lead
Breather hose
Band
Battery
1
1
1
2
1
7-2
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY” in chapter 5.
Refer to “EXHAUST MANIFOLD” in
chapter 5.
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
11
Procedure/Part name
Damper
Bolt
Battery box
Coupler
Bolt
Electrical box
Q’ty
1
4
1
4
4
1
Service points
For multi-function meter
Reverse the removal steps for installation.
7-3
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Q’ty
1
2
Procedure/Part name
ELECTRICAL BOX DISASSEMBLY
Clamp
Coupler
3
4
5
6
7
8
9
10
Screw
Rectifier/regulator
Screw
Cover
Packing
Spark plug lead holder
Spark plug lead/cap
Screw
2
1
10
1
1
3
3/3
6
5
3
7-4
Service points
Follow the left “Step” for disassembly.
For overheat, exhaust temperature
sensor and lighting coil
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
Step
11
12
13
14
15
16
17
18
19
20
21
22
Procedure/Part name
Ground lead
Ignition coil
Ignition coil lead
Bolt
Ground lead
Lead
Nut
Starter motor lead
Battery positive lead
Fuse lead
Starter relay lead
Starter relay
Q’ty
3
3
3
3
6
3
2
1
1
1
1
1
7-5
Service points
Black/Orange
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
Step
23
24
25
26
27
28
29
30
31
32
Procedure/Part name
Lead holder
Fuse lead
Screw
Fuse holder
Lead/coupler
Screw
Coupler bracket
CDI unit
Screw
Lead holder plate
Q’ty
1
5
2
1
1/6
2
1
1
8
2
Service points
Reverse the disassembly steps for
assembly.
7-6
ELEC
1
2
3
4
5
6
7
8
9
–
+
Ignition coil
CDI unit
Rectifier/regulator
Fuse holder
Starter relay
Tape
Clear tube
Red tube
White tape
ELECTRICAL BOX
E
Å To battery positive terminal
ı To starter motor
Ç Affix the ignition coil connector to
the electrical box holder.
Î Pass the 8 pin coupler leads behind
the CDI unit and insert them into
the bracket.
Br
G
Gy
: Brown
: Green
: Gray
7-7
O
R
W
B/O
B/W
B/Y
Gy/B
Gy/R
Gy/Y
R/W
R/Y
: Orange
: Red
: White
: Black/Orange
: Black/White
: Black/Yellow
: Gray/Black
: Gray/Red
: Gray/Yellow
: Red/White
: Red/Yellow
ELEC
–
+
ELECTRICAL ANALYSIS
E
ELECTRICAL ANALYSIS
INSPECTION
CAUTION:
● All
measuring instruments should be handled with special care. Damaged or mishandled instruments will not measure
properly.
● On an instrument powered by dry batteries, check the battery’s voltage periodically and replace the batteries if
necessary.
Digital circuit tester
NOTE:
Throughout this chapter the digital circuit
tester’s part number has been omitted.
Refer to the following part number.
Digital circuit tester:
J-39299/90890-06752
NOTE:
“
” indicates a continuity of electricity; i.e., a closed circuit at the respective
switch position.
7-8
ELEC
–
+
ELECTRICAL ANALYSIS
E
Low resistance measurement
NOTE:
● When measuring a resistance of 10 Ω or
less with the digital tester, the correct
measurement
cannot
be
obtained
because of the tester’s internal resistance.
● To obtain the correct value, subtract the
internal resistance from the displayed
measurement.
● The internal resistance of the tester can be
obtained by connecting both of its terminals.
Correct value =
Displayed measurement –
Internal resistance
Peak voltage measurement
NOTE:
● When checking the condition of the ignition system it is vital to know the peak
voltage.
● Cranking speed is dependant on many
factors (e.g., fouled or weak spark plugs, a
weak battery). If one of these is defected,
the peak voltage will be lower than specification.
● If the peak voltage measurement is not
within specification the engine will not
operate properly.
● A low peak voltage will also cause components to prematurely wear.
Peak voltage adaptor
NOTE:
● Throughout this chapter the peak voltage
adaptor’s part number has been omitted.
Refer to the following part number.
● The peak voltage adaptor should be used
with the digital circuit tester.
Peak voltage adaptor:
YU-39991/90890-03169
7-9
ELEC
–
+
ELECTRICAL ANALYSIS
Å
●
E
When measuring the peak voltage, connect the peak voltage adaptor to the digital tester and switch the selector to the
DC voltage mode.
NOTE:
● Make sure that the adaptor leads are
properly installed in the digital circuit
tester.
● Make sure that the positive pin (the “+”
mark facing up as shown) on the adaptor
is installed into the positive terminal of
the tester.
● The test harness is needed for the following tests.
ı
Å Voltage measurement
ı Peak voltage measurement
Test harness
YW-
90890-
Pin
06780
06780
6
Usage
Pick-up coil and
lighting coil
Checking steps:
● Disconnect the coupler connections.
● Connect the test harness between the
couplers.
● Connect the tester terminals to the terminals which are being checked.
● Run the engine and observe the measurement.
NOTE:
● Make sure the output lead (red lead) of the
rectifier/regulator is disconnected when
measuring the peak voltage of the lighting
coil and rectifier/regulator.
● If the lighting coil and pickup coil(s) are
measured unloaded, disconnect the test
harness on the output side coupler.
7-10
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SYSTEM
WIRING DIAGRAM
1
2
3
4
5
6
7
8
9
0
A
B
O
R
W
B/O
B/W
B/Y
W/R
Engine stop switch
Engine stop lanyard switch
Lighting coil
Pickup coil
CDI unit
Ignition coil
Spark plug
Battery
Rectifier/regulator
Exhaust temperature sensor
Water temperature sensor
7-11
: Black
: Orange
: Red
: White
: Black/Orange
: Black/White
: Black/Yellow
: White/Red
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SPARK GAP
WARNING
● When
checking the spark gap, do not
touch any of the connections of the spark
gap tester lead wires.
● When performing the spark gap test, take
special care not to let sparks leak out of
the removed spark plug cap.
● When performing the spark gap check,
keep flammable gas or liquids away,
since this test can produce sparks.
Å
1. Check:
● Ignition spark gap
Below specification → Continue to
check the CDI unit output.
Spark gap:
10 mm (0.39 in)
ı
Checking steps:
Remove the spark plugs from the
engine.
● Connect the spark plug cap to the
spark gap tester.
● Set the spark gap length on the adjusting knob.
●
Spark gap tester:
YM-34487/90890-06754
●
Crank the engine and observe the ignition system spark through the discharge window.
Å For USA and CANADA
ı For worldwide
7-12
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SYSTEM PEAK VOLTAGE
WARNING
When checking the CDI unit do not touch
any of the connections of the digital tester
lead wires.
NOTE:
● If there is no spark, or the spark is weak,
continue with the ignition system test.
● If a good spark is obtained, the problem is
not with the ignition system, but possibly
with the spark plug(-s) or another component.
1. Measure:
● CDI unit output peak voltage
Above specification → Replace the
ignition coil.
Below specification → Measure the
rectifier output peak voltage.
Replace the CDI unit.
CDI unit output peak voltage:
Black/Orange (B/O) – Black (B):
Black/White (B/W) – Black (B):
Black/Yellow (B/Y) – Black (B):
200 V @ cranking 1
180 V @ cranking 2
190 V @ 2,000 r/min
180 V @ 3,500 r/min
Cranking 1: unloaded
Cranking 2: loaded
NOTE:
B/O – B for cylinder #1.
B/W – B for cylinder #2.
B/Y – B for cylinder #3.
7-13
ELEC
–
+
IGNITION SYSTEM
E
2. Measure:
● Pick-up coil output peak voltage
Below specification → Replace the
pick-up coil.
Pick-up coil output peak voltage:
White/Red (W/R) –
Black/Orange (B/O):
5 V @ cranking 1
2.8 V @ cranking 2
7.9 V @ 2,000 r/min
11 V @ 3,500 r/min
NOTE:
The starter motor will not operate when the
test harness on the output side coupler is
disconnected to measure the unloaded
peak voltage for the pickup coil(s) and lighting coil. Therefore, connect the black lead
of the test harness to the ground with a
lead.
3. Measure:
● Lighting coil output peak voltage
Below specification → Replace the
lighting coil.
Lighting coil output peak voltage:
Green (G) – Green (G):
9 V @ cranking 1
9 V @ cranking 2
14 V @ 2,000 r/min
14 V @ 3,500 r/min
4. Measure:
● Rectifier output peak voltage
Below specification → Replace the
rectifier/regulator.
Rectifier output peak voltage:
Red (R) – Black (B):
7 V @ cranking 2
12.6 V @ 2,000 r/min
12.6 V @ 3,500 r/min
Cranking 1: unloaded
Cranking 2: loaded
7-14
ELEC
–
+
IGNITION SYSTEM
E
BATTERY
Refer to “ELECTRICAL” in chapter 3.
FUSE
Refer to “STARTING SYSTEM”.
SPARK PLUGS
Refer to “ELECTRICAL” in chapter 3.
SPARK PLUG LEAD ASSEMBLY
1. Inspect:
● Spark plug lead assembly
Cracks/damage → Replace.
2. Measure:
● Spark plug lead resistance
Out of specification → Replace.
Spark plug lead resistance:
#1: 6.1 ~ 14.3 kΩ
#2: 4.6 ~ 11.1 kΩ
#3: 3.1 ~ 7.7 kΩ
IGNITION COIL
1. Measure:
● Primary coil resistance
Out of specification → Replace.
Primary coil resistance:
Black/White (B/W) – Body
0.26 ~ 0.36 Ω at 20 ˚C (68 ˚F)
NOTE:
When measuring a resistance of 10 Ω or
less with the digital tester, the correct measurement cannot be obtained because of
the tester’s internal resistance.
Refer to “Low resistance measurement”.
7-15
ELEC
–
+
IGNITION SYSTEM
E
2. Measure:
● Secondary coil resistance
Out of specification → Replace.
Secondary coil resistance:
Black/White (B/W) – Spark plug
lead terminal
3.5 ~ 4.7 kΩ at 20 ˚C (68 ˚F)
ENGINE STOP SWITCH
1. Check:
● Engine stop switch continuity
Out of specification → Replace.
Engine stop switch continuity
(black coupler)
Lock plate
Installed
Removed
Position
Lead color
White
Black
Free
Push
Free
Push
WATER TEMPERATURE SENSOR
1. Measure:
● Water temperature sensor resistance
(at the specified temperature)
Out of specification → Replace.
Water temperature sensor
resistance:
0 ˚C (32 ˚F): 24.0 ~ 37.1 kΩ
100 ˚C (212 ˚F): 0.87 ~ 1.18 kΩ
200 ˚C (392 ˚F): 0.104 ~ 0.153 kΩ
Measurement steps:
Ice the water temperature sensor and
measure the resistance.
● Suspend the water temperature sensor in a container filled with oil.
● Slowly heat the oil.
● Measure the resistance when the specified temperature is reached.
●
7-16
ELEC
–
+
IGNITION SYSTEM
E
EXHAUST TEMPERATURE SENSOR
1. Measure:
● Exhaust temperature sensor resistance (at the specified temperature)
Out of specification → Replace.
Exhaust temperature sensor
resistance:
300 ˚C (572 ˚F): 73 ~ 241 kΩ
600 ˚C (1,112 ˚F): 0.86 ~ 1.58 kΩ
900 ˚C (1,652 ˚F): 64 ~ 90 Ω
Measurement steps:
Heat the exhaust temperature sensor
using an electric furnace or equivalent.
● Measure the resistance when the specified temperature.
●
7-17
ELEC
–
+
STARTING SYSTEM
E
STARTING SYSTEM
WIRING DIAGRAM
1
2
3
4
5
6
7
8
CDI unit
Engine stop lanyard switch
Starter switch
Multi-function meter
Fuse
Starter relay
Starter motor
Battery
B
Br
R
R/Y
7-18
: Black
: Brown
: Red
: Red/Yellow
ELEC
–
+
STARTING SYSTEM
E
BATTERY
Refer to “ELECTRICAL” in chapter 3.
WIRING CONNECTIONS
1. Check:
● Wiring connections
Poor connections → Properly connect.
FUSE
1. Check:
● Fuse holder continuity
No continuity → Check the fuse or
replace the fuse holder.
Fuse holder continuity:
Between 1 and 2
Between 3 and 4
2. Check:
● Fuse broken
Broken → Replace.
Fuse rating:
10A, 20A
NOTE:
20A fuse is for CDI unit and rectifier/regulator.
10A fuse is for multi-function meter, YPVS
motor and start switch.
7-19
ELEC
–
+
STARTING SYSTEM
E
STARTER SWITCH
1. Check:
● Continuity
Out of specification → Replace.
Starter continuity
(red coupler)
Lock plate
Installed
Removed
Position
Leads
Red
Brown
Free
Push
Free
Push
STARTER RELAY
1. Inspect:
● Brown lead terminal
● Black lead terminal
Loose → Tighten.
2. Check:
● Starter relay
Faulty → Replace.
Checking steps:
Connect the tester leads between the
starter relay terminals as shown.
● Connect the brown lead terminal to
the positive battery terminal.
● Connect the black lead terminal to the
negative battery terminal.
● Check that there is continuity between
the starter relay terminals.
● Check that there is no continuity after
the brown or black lead is removed.
●
7-20
ELEC
–
+
STARTER MOTOR
E
STARTER MOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
STARTER MOTOR
DISASSEMBLY
Starter motor
O-ring
Bolt
Starter motor front cover
O-ring
Oil seal retainer
Washer
Shim
Q’ty
Service points
Follow the left “Step” for disassembly.
Refer to “GENERATOR AND STARTER
MOTOR” in chapter 5.
1
2
1
1
1
1
*
*: As required
7-21
t = 0.2 mm, 0.5 mm
ELEC
–
+
STARTER MOTOR
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
16
17
Procedure/Part name
Starter motor rear cover
O-ring
Shim
Armature assembly
Nut/spring washer/washer
O-ring
Brush holder
Brush spring
Bolt
Brush assembly
Q’ty
1
1
*
1
1/1/4
1
1
4
1
1
*: As required
7-22
Service points
t = 0.2 mm, 0.8 mm
ELEC
–
+
STARTER MOTOR
E
EXPLODED DIAGRAM
Step
18
19
20
Procedure/Part name
Spacer
Holder
Starter motor yoke
Q’ty
1
1
1
Service points
Reverse the disassembly steps for
assembly.
7-23
ELEC
–
+
STARTER MOTOR
E
SERVICE POINTS
Armature inspection
1. Inspect:
● Armature shaft 1
Damage/wear → Replace.
2. Inspect:
● Commutator
Dirt → Clean with 600 grit sandpaper.
3. Measure:
● Commutator diameter
Out of specification → Replace.
Min. commutator diameter:
27.0 mm (1.06 in)
4. Check:
● Commutator undercut
Contaminants → Clean.
NOTE:
Remove all mica and metal particles with
compressed air.
5. Measure:
● Commutator undercut
Out of specification → Replace.
Min. commutator undercut:
0.2 mm (0.01 in)
7-24
ELEC
–
+
STARTER MOTOR
E
6. Inspect:
● Armature coil continuity
Out of specification → Replace.
Armature coil continuity:
Commutator segments 1 Continuity
Segment - Laminations 2 No continuity
Segment - Armature shaft No continuity
Brush holder inspection
1. Measure:
● Brush length a
Out of specification → Replace.
Min. brush length:
6.5 mm (0.26 in)
2. Check:
● Brush holder continuity
Out of specification → Replace.
Brush holder continuity:
Brush holder - Base
No continuity
Starter motor front cover inspection
1. Inspect:
● Starter motor front cover bushing
Damage/wear → Replace the starter
motor front cover.
7-25
ELEC
–
+
CHARGING SYSTEM
E
CHARGING SYSTEM
WIRING DIAGRAM
1
2
3
4
Lighting coil
Battery
Fuse (20A)
Rectifier/regulator
B
G
R
G/W
7-26
: Black
: Green
: Red
: Green/White
ELEC
–
+
CHARGING SYSTEM
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
LIGHTING COIL
Refer to “IGNITION SYSTEM”.
RECTIFIER/REGULATOR
Refer to “IGNITION SYSTEM”.
7-27
ELEC
–
+
YPVS
E
YPVS
WIRING DIAGRAM
1
2
3
4
5
6
7
B
Gy
R
B/O
R/L
R/W
W/R
Lighting coil
Pickup coil
CDI unit
YPVS servomotor
Fuse
Battery
Rectifier/regulator
7-28
: Black
: Gray
: Red
: Black/Orange
: Red/Blue
: Red/White
: White/Red
ELEC
–
+
YPVS
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
PICKUP COIL
Refer to “IGNITION SYSTEM”.
CDI UNIT
Refer to “IGNITION SYSTEM”.
LIGHTING COIL
Refer to “IGNITION SYSTEM”.
RECTIFIER/REGULATOR
Refer to “IGNITION SYSTEM”.
7-29
ELEC
–
+
YPVS SERVOMOTOR
E
YPVS SERVOMOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
YPVS SERVOMOTOR REMOVAL
Bolt
Cable holder
YPVS servomotor coupler
Bolt
YPVS servomotor
Spacer
YPVS cable
Cover
Q’ty
2
1
1
2
1
2
2
1
Service points
Follow the left “Step” for removal.
White tape is for No. 2 cable.
Reverse the removal steps for installation.
7-30
ELEC
–
+
YPVS SERVOMOTOR
E
SERVICE POINTS
YPVS cable removal and installation
1. Remove:
● YPVS cables 1 and 2
Removal steps:
● Remove the YPVS cable holder 1.
● Remove the YPVS cables 2 from the
both drams.
NOTE:
There is a white paint mark a on YPVS
cable 2.
YPVS cable inspection
1. Inspect:
● YPVS cables 1 and 2
Frays/kinks/rough movement →
Replace.
YPVS servomotor inspection
1. Check:
● YPVS servomotor
YPVS servomotor does not move →
Replace.
Checking steps:
● Connect the battery (12 V) to the YPVS
servomotor coupler as shown.
Battery positive terminal →
Red (R) terminal 1
Battery negative terminal →
Black (B) terminal 2
●
Install a jumper lead 4 between the
black 2 and gray 3 terminals as
shown. Only install the jumper lead for
1 or 2 seconds.
Black (B) terminal 2 ↔
Gray (Gy) terminal 3
7-31
ELEC
–
+
YPVS SERVOMOTOR
E
Make sure the servomotor operates
properly.
NOTE:
Make sure the pulley operates three seconds after the jumper lead is removed.
●
CAUTION:
Do not disassemble the YPVS servomotor
unit. It is a sealed unit and if it is faulty it
must be replaced.
YPVS cable adjustment
Refer to “CONTROL SYSTEM” in
chapter 3.
7-32
ELEC
–
+
INDICATION SYSTEM
E
INDICATION SYSTEM
WIRING DIAGRAM
1
2
3
4
5
6
7
8
9
0
A
B
CDI unit
Fuel level sensor
Oil level sensor
Buzzer
Multi-function meter
Speed sensor
Engine stop lanyard switch
Starter switch
Battery
Fuse
Exhaust temperature sensor
Water temperature sensor
B
Br
Ch
G
Gy
L
O
R
Y
B/O
B/Y
: Black
: Brown
: Chocolate
: Green
: Gray
: Blue
: Orange
: Red
: Yellow
: Black/Orange
: Black/Yellow
7-33
Gy/B
Gy/R
Gy/Y
L/B
L/R
R/B
R/W
R/Y
W/L
: Gray/Black
: Gray/Red
: Gray/Yellow
: Blue/Black
: Blue/Red
: Red/Black
: Red/White
: Red/Yellow
: White/Blue
ELEC
–
+
INDICATION SYSTEM
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
LIGHTING COIL
Refer to “CHARGING SYSTEM”.
RECTIFIER/REGULATOR
Refer to “CHARGING SYSTEM”.
CDI UNIT
Refer to “IGNITION SYSTEM”.
WATER TEMPERATURE SENSOR
Refer to “IGNITION SYSTEM”.
EXHAUST TEMPERATURE SENSOR
Refer to “IGNITION SYSTEM”.
BUZZER
1. Check:
● Buzzer
Buzzer does not sound → Replace.
Checking steps:
Connect the battery (12 V) to the
buzzer coupler as shown.
●
Battery positive terminal →
Red (R) terminal 1
Battery negative terminal →
Black (B) terminal 2
OIL LEVEL SENSOR
1. Measure:
● Oil level sensor resistance
Out of specification → Replace.
Blue (L) – Black (B)
Float position
7-34
Resistance (Ω)
A
292 ~ 308
B
97 ~ 103
C
0~3
ELEC
–
+
INDICATION SYSTEM
E
FUEL LEVEL SENSOR
1. Measure:
● Fuel level sensor resistance
Out of specification → Replace.
White/blue (W/L) – Black (B)
Float position
Resistance (Ω)
A
757 ~ 803
B
0~8
MULTI-FUNCTION METER
Multi-function meter
1. Check:
● Multi-function meter
Cracked meter housing → Replace
the multi-function meter.
Meter is fogged/shows signs of water
intrusion → Replace the multi-function meter.
7-35
ELEC
–
+
INDICATION SYSTEM
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
MULTI-FUNCTION METER
REMOVAL
Multi-function meter coupler
Nut/washer
Holder
Multi-function meter
Q’ty
Service points
Follow the left “Step” for removal.
8
2/2
1
1
Reverse the removal steps for installation.
7-36
ELEC
–
+
INDICATION SYSTEM
E
Display function
1. Check:
● Display function
Not operate → Replace the multifunction meter.
1 Oil level sensor
2 Fuel level sensor
3 Buzzer
4 Electrical box
5 Start switch
6 Battery
7 Speed sensor
*: Disconnected
B
Br
Ch
G
Gy
L
R
Y
Gy/B
: Black
: Brown
: Chocolate
: Green
: Gray
: Blue
: Red
: Yellow
: Gray/Black
7-37
Gy/R
Gy/Y
L/B
L/R
R/B
R/W
R/Y
W/L
: Gray/Red
: Gray/Yellow
: Blue/Black
: Blue/Red
: Red/Black
: Red/White
: Red/Yellow
: White/Blue
ELEC
–
+
INDICATION SYSTEM
E
Checking steps:
● Connect the battery terminals to the
white six-pin connector as shown.
NOTE:
If the multi-function meter has been
removed from the water vehicle, supply
DC 12 voltage to the connector (+: red, –:
black) with a battery.
Disconnect the blue one-pin connector
1 and make sure the “WARNING”
lamp 2 lights.
NOTE:
If the “WARNING” lamp does not light,
disconnect the battery and then reconnect it.
●
Press the “A/SET” 3 and “C” 5 buttons at the same time. While still
pressing the two buttons, press the
“MODE” button 6 and hold all three
for more than 3 seconds. The self-indicating function will then activate.
NOTE:
If the “
” message displays, reconnect and then disconnect the blue onepin connector.
●
Sequential output (73 seconds/cycle)
1
Display begins operation
2
“
”
3
All LCD readouts turn on
4
“
” is displayed
5
“
” is displayed
6
“
” is displayed
7
“
” is displayed
8
“
” is displayed
9
“
” is displayed
10
“
” is displayed
11
“
” is displayed
12
“
” is displayed
13
“
” is displayed
14
“
” is displayed
15
“
” is displayed
●
●
7-38
Press either button 3, 4, 5, or 6. The
self-indicating function will then stop
and the “WARNING” lamp 2 will light.
Reconnect the blue one-pin connector.
The “WARNING” lamp 2 will turn off.
ELEC
–
+
INDICATION SYSTEM
E
Fuel level gauge
1. Check:
● Fuel level gauge
Not operating → Replace the multifunction meter.
Checking steps:
Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Disconnect the green two-pin connector (white/blue and black leads).
● Connect the white/blue and black terminals with a jumper lead 1.
● Connect the green and red terminals
with a jumper lead 2.
NOTE:
If the jumper lead is installed for more
than 30 seconds, the display will automatically turn off.
●
●
●
●
●
7-39
Check the fuel level segments is full
indicated.
Remove the jumper lead from the
green two-pin connector.
Disconnect the jumper lead 2 and
then connect it to green and red terminal again.
Make sure the fuel low level segment
3, fuel level warning indicator 4
and “
” message 5 blinks, and
the “WARNING” lamp 6 operates
properly, and the buzzer sounds intermittently.
ELEC
–
+
INDICATION SYSTEM
E
Oil level gauge
1. Check:
● Oil level gauge
Not operating → Replace the multifunction meter.
Checking steps:
Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Disconnect the white two-pin connector (blue and black leads).
● Connect the blue and black terminals
with a jumper lead 1.
● Connect the green and red terminals
with a jumper lead 2.
NOTE:
If the jumper lead is installed for more
than 30 seconds, the display will automatically turn off.
●
●
●
●
●
7-40
Check the oil level segments is full
indicated.
Remove the jumper lead from the
white two-pin connector.
Disconnect the jumper lead 2 and
then connect it to green and red terminal again.
Make sure the oil low level segment
3, oil level warning indicator 4 and
“
” message 5 blinks, and the
“WARNING” lamp 6 operates properly, and the buzzer sounds intermittently.
ELEC
–
+
INDICATION SYSTEM
E
Overheat warning indicator
1. Check:
● Overheat 1 warning indicator
Not operating → Replace the multifunction meter.
Checking steps:
Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Connect the gray/black and black terminals with a jumper lead 1.
● Connect the green and red terminals
with a jumper lead 2.
● Make sure the water temperature
warning indicator blinks 3 and the
“
” message 4 blinks, the
“WARNING” lamp 5 blinks, and the
buzzer sounds intermittently.
●
2. Check:
● Overheat 2 warning indicator
Not operating → Replace the multifunction meter.
Checking steps:
● Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Connect the gray/red and black terminals with a jumper lead 1.
● Connect the green and red terminals
with a jumper lead 2.
7-41
ELEC
–
+
INDICATION SYSTEM
E
●
Make sure the water temperature
warning indicator display 3 and the
“
” message 4 display, the
“WARNING” lamp 5 operates properly, and the buzzer sounds continuity.
3. Check:
● Exhaust temperature warning
indicator
Not operating → Replace the multifunction meter.
Checking steps:
● Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Connect the gray/yellow and black terminals with a jumper lead 1.
● Connect the green and red terminals
with a jumper lead 2.
● Make sure the exhaust temperature
warning indicator blinks 3 and the
“
” message 4 blinks, the
“WARNING” lamp 5 operates properly, and the buzzer sounds intermittently.
7-42
ELEC
–
+
INDICATION SYSTEM
E
Speed meter
1. Check:
● Speed meter output voltage
Within specification → Check the speed
sensor output voltage and pulses.
Out of specification → Replace.
Speed meter output voltage:
10.5 V
Checking steps:
Supply DC 12 voltage to the white sixpin connector (+: red, –: black) with a
battery.
● Disconnect the blue one-pin connector
1 and make sure the “WARNING” lamp
lights 2.
NOTE:
If the “WARNING” lamp does not light,
disconnect the battery and then reconnect it.
●
●
7-43
Measure the voltage on the speed
meter connector (white three-pin connector) (between the red/white and
black leads).
ELEC
–
+
INDICATION SYSTEM
E
Speed sensor
1. Check:
● Speed sensor output voltage and
pulses
Out of specification → Replace.
Speed sensor output voltage
(dependant on the paddle wheel
position):
Less than 400 mV/11.6 - 12 V
Output pulse:
2 pulses/one-full turn
Checking steps:
● Apply DC 12 voltage to the white
three-pin connector (between the red/
white and black leads).
● Rotate the paddle wheel by hand and
measure the voltage between the
black and yellow leads.
NOTE:
As the paddle wheel is rotated, a squarewave voltage signal a is produced.
●
7-44
Two pulses occur every time the paddle wheel makes one-full turn.
HULL
HOOD
E
CHAPTER 8
HULL AND HOOD
HANDLEBAR ................................................................................................... 8-1
EXPLODED DIAGRAM ............................................................................. 8-1
REMOVAL AND INSTALLATION CHART ............................................... 8-1
SERVICE POINTS ..................................................................................... 8-6
Handlebar inspection........................................................................ 8-6
Handlebar switch inspection............................................................ 8-6
Handlebar assembly installation ..................................................... 8-6
QSTS GRIP...................................................................................................... 8-8
EXPLODED DIAGRAM ............................................................................. 8-8
REMOVAL AND INSTALLATION CHART ............................................... 8-8
SERVICE POINTS ................................................................................... 8-10
QSTS cable inspection.................................................................... 8-10
QSTS grip inspection...................................................................... 8-10
STEERING MASTER..................................................................................... 8-11
EXPLODED DIAGRAM ........................................................................... 8-11
REMOVAL AND INSTALLATION CHART ............................................. 8-11
SERVICE POINTS ................................................................................... 8-14
Steering master components inspection ...................................... 8-14
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD ...................... 8-15
EXPLODED DIAGRAM ........................................................................... 8-15
REMOVAL AND INSTALLATION CHART ............................................. 8-15
SERVICE POINTS ................................................................................... 8-18
Remote control cables inspection ................................................. 8-18
Steering cable (jet pump side) installation ................................... 8-18
Steering cable stopper installation................................................ 8-18
QSTS cable (jet pump side) installation........................................ 8-19
QSTS cable stopper installation .................................................... 8-19
Shift cable (jet pump side) installation.......................................... 8-19
Shift cable stopper installation ...................................................... 8-20
Remote control cables adjustment................................................ 8-20
FRONT HOOD ............................................................................................... 8-21
EXPLODED DIAGRAM ........................................................................... 8-21
REMOVAL AND INSTALLATION CHART ............................................. 8-21
STEERING MASTER COVER ....................................................................... 8-23
EXPLODED DIAGRAM ........................................................................... 8-23
REMOVAL AND INSTALLATION CHART ............................................. 8-23
HULL
HOOD
HOSES........................................................................................................... 8-24
EXPLODED DIAGRAM ........................................................................... 8-24
REMOVAL AND INSTALLATION CHART ............................................. 8-24
SERVICE POINTS ................................................................................... 8-26
Check valve inspection ................................................................... 8-26
SHIFT LEVER ................................................................................................ 8-27
EXPLODED DIAGRAM ........................................................................... 8-27
REMOVAL AND INSTALLATION CHART ............................................. 8-27
SHIFT LEVER ................................................................................................ 8-28
EXPLODED DIAGRAM ........................................................................... 8-28
REMOVAL AND INSTALLATION CHART ............................................. 8-28
SERVICE POINTS ................................................................................... 8-30
Base assembly................................................................................. 8-30
SEATS AND HAND GRIP ............................................................................. 8-31
EXPLODED DIAGRAM ........................................................................... 8-31
REMOVAL AND INSTALLATION CHART ............................................. 8-31
SERVICE POINTS ................................................................................... 8-33
Seat lock inspection ........................................................................ 8-33
EXHAUST SYSTEM...................................................................................... 8-34
EXPLODED DIAGRAM ........................................................................... 8-34
REMOVAL AND INSTALLATION CHART ............................................. 8-34
SERVICE POINTS ................................................................................... 8-36
Exhaust system inspection............................................................. 8-36
DECK AND HULL .......................................................................................... 8-37
EXPLODED DIAGRAM ........................................................................... 8-37
REMOVAL AND INSTALLATION CHART ............................................. 8-37
ENGINE MOUNT .......................................................................................... 8-39
EXPLODED DIAGRAM ........................................................................... 8-39
REMOVAL AND INSTALLATION CHART ............................................. 8-39
HULL REPAIR ......................................................................................... 8-40
Shallow scratches ........................................................................... 8-40
Deep scratches ................................................................................ 8-40
Cracks and punctures ..................................................................... 8-41
Insert nut.......................................................................................... 8-42
Graphic removal.............................................................................. 8-44
Graphic installation......................................................................... 8-44
E
1
2
3
4
5
6
7
8
9
HULL
HOOD
HANDLEBAR
E
HANDLEBAR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
HANDLEBAR COVER REMOVAL
Screw
Handlebar cover
Band
Pad
Bolt
Handlebar cover stay
Throttle cable
Bolt
Upper handlebar holder
Q’ty
Service points
Follow the left “Step” for removal.
4
1
2
1
2
1
1
4
2
Reverse the removal steps for installation.
8-1
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
HANDLEBAR REMOVAL
QSTS cable (to jet nozzle)
Bolt
QSTS converter
QSTS cable 2
QSTS cable 1
Handlebar switch coupler
Q’ty
2
1
1
1
3
8-2
Service points
Follow the left “Step” for removal.
Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
with white tape
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
11
Procedure/Part name
Buzzer coupler
Screw
Handle boss cover
Band
Handlebar assembly
Buzzer
Q’ty
1
4
1
2
1
1
Service points
Reverse the removal steps for installation.
8-3
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
HANDLEBAR DISASSEMBLY
Bolt
Grip end
Spacer
Screw/washer/spring washer
QSTS grip assembly
Screw
Q’ty
2
2
1
1/1/1
1
2
8-4
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
Procedure/Part name
Handlebar switch assembly
Screw
Throttle lever assembly
Handlebar grip
Handlebar
Q’ty
1
2
1
1
Service points
NOTE:
Apply adhesive to the handlebar and the
inner surface of the handlebar grip.
1
Reverse the disassembly steps for
assembly.
8-5
HULL
HOOD
HANDLEBAR
E
SERVICE POINTS
Handlebar inspection
1. Inspect:
● Handlebar
Bends/cracks/damage → Replace.
Handlebar switch inspection
Refer to “STARTING SYSTEM” in
chapter 7.
Handlebar assembly installation
1. Install:
● QSTS cables
● Buzzer lead
● Handlebar switch lead
● Throttle cable
NOTE:
After inserting the cables and leads into the
grommets, tie the end of grommets with
the bands 1.
2. Install:
● Upper handlebar holder 1
CAUTION:
Clearance a should be narrower than
clearance b.
Reference clearance:
a: 1.5 mm (0.06 in)
b: 3.5 mm (0.14 in)
NOTE:
● Align the punch mark c on the handlebar
with the top surface of the handlebar
holder.
● The upper handlebar holder should be
installed with the punch mark d facing
forward.
8-6
HULL
HOOD
HANDLEBAR
E
3. Adjust:
● QSTS cable length a
QSTS cable length:
77 ± 0.5 mm (3.03 ± 0.02 in)
NOTE:
● Before adjusting the QSTS cables, set the
trim grip to the neutral position.
● Adjust the QSTS cable lengths a to the
specified length and be sure to take up
any slack.
4. Adjust:
● Throttle cable free play
Refer to “CONTROL SYSTEM” in
chapter 3.
5. Adjust:
● QSTS cable free play
Refer to “CONTROL SYSTEM” in
chapter 3.
8-7
HULL
HOOD
QSTS GRIP
E
QSTS GRIP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
QSTS GRIP DISASSEMBLY
QSTS grip assembly
Screw/washer
Cover
Ball
Spring
QSTS cable 1
QSTS cable 2
Q’ty
1/1
1
2
2
1
1
8-8
Service points
Follow the left “Step” for disassembly.
Refer to “HANDLEBAR”.
NOTE:
QSTS cable 2 has white tape a on its
end.
HULL
HOOD
QSTS GRIP
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
Procedure/Part name
Screw/washer
Spacer
QSTS grip position locator
Spring
Spacer
Cable housing
QSTS grip
Q’ty
2/2
1
1
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
8-9
HULL
HOOD
QSTS GRIP
E
SERVICE POINTS
QSTS cable inspection
1. Inspect:
● QSTS cables
Frays/kinks/rough movement →
Replace.
QSTS grip inspection
1. Inspect:
● QSTS grip
Damage/wear → Replace.
8-10
HULL
HOOD
STEERING MASTER
E
STEERING MASTER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
STEERING MASTER REMOVAL
Handlebar assembly
Steering master cover
Bolt/washer
Steering arm
Nut/washer
Steering master assembly
Bolt
Grommet
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “HANDLEBAR”.
Refer to “STEERING MASTER COVER”.
1/1
1
4/4
1
4
2
Reverse the removal steps for installation.
8-11
HULL
HOOD
STEERING MASTER
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
10
Procedure/Part name
STEERING MASTER
DISASSEMBLY
Bolt/washer
Stay
Spring
Bolt/washer
Lower housing
Spring
Bushing
Bushing
Upper housing
Tilt lever
Q’ty
2/2
1
1
6/6
1
1
1
1
1
1
8-12
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
STEERING MASTER
E
EXPLODED DIAGRAM
Step
11
12
13
14
15
16
17
18
19
Procedure/Part name
Tilt stopper
Bolt/nut
Retainer
Steering shaft assembly
Steering tube
Bolt/washer/spring washer
Cap
Shaft 1
Cross piece
Q’ty
1
4/4
2
1
1
2/2/2
1
1
1
Service points
Reverse the disassembly steps for
assembly.
8-13
HULL
HOOD
STEERING MASTER
E
SERVICE POINTS
Steering master components inspection
1. Inspect:
● Each component part
Damage/wear → Replace the steering master.
8-14
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD
REMOVAL
Speed sensor coupler
Cap
Nut
Speed sensor
Steering cable end
Nut/washer
Bracket
Q’ty
1
1
1
1
1
3/3
1
8-15
Service points
Follow the left “Step” for removal.
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
16
Procedure/Part name
Nut
Steering cable holder
Cap
Nut
Steering cable
Shift cable end
Bolt
Shift cable holder
Cap
Q’ty
2
1
1
1
1
1
2
1
1
8-16
Service points
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
EXPLODED DIAGRAM
Step
17
18
19
20
21
22
23
24
Procedure/Part name
Nut
Shift cable
Nut
Pin
QSTS cable end
Cap
Nut
QSTS cable
Q’ty
1
1
1
1
1
1
1
1
Service points
Reverse the removal steps for installation.
8-17
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
SERVICE POINTS
Remote control cables inspection
1. Inspect:
● Steering cable
● QSTS cable
● Shift cable
Frays/kinks/rough movement →
Replace.
Steering cable (jet pump side) installation
1. Install:
● Steering cable a
Steering cable set length
(jet pump side):
13.5 ~ 15.5 mm (0.53 ~ 0.61 in)
WARNING
The steering cable must be screwed in at
least 8 mm (0.31 in).
Steering cable stopper installation
1. Install:
● Steering cable stopper
WARNING
Be sure to fit the projection 1 on the steering cable stopper into the groove in the
outer cable.
8-18
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
QSTS cable (jet pump side) installation
1. Install:
● QSTS cable (jet pump side) a
QSTS cable set length
(jet pump side):
12.0 ~ 14.0 mm (0.47 ~ 0.55 in)
WARNING
The QSTS cable must be screwed in more
than 8 mm (0.31 in).
QSTS cable stopper installation
1. Install:
● QSTS cable stopper
WARNING
Be sure to fit the projection 1 on the QSTS
cable stopper into the groove in the outer
cable.
Shift cable (jet pump side) installation
1. Install:
● Shift cable (jet pump side) a
Shift cable set length
(jet pump side):
12.2 ~ 13.8 mm (0.48 ~ 0.54 in)
WARNING
The shift cable must be screwed in more
than 8 mm (0.31 in).
8-19
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
Shift cable stopper installation
1. Install:
● Shift cable stopper
WARNING
Be sure to fit the projection 1 on the shift
cable stopper into the groove in the outer
cable.
Remote control cables adjustment
Refer to “CONTROL SYSTEM” in
chapter 3.
8-20
HULL
HOOD
FRONT HOOD
E
FRONT HOOD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
FRONT HOOD REMOVAL
Nut/washer
Front hood assembly
Circlip
Pin
Damper
Bolt
Hood lock assembly
Q’ty
4/4
1
4
2
2
2
1
8-21
Service points
Follow the left “Step” for removal.
HULL
HOOD
FRONT HOOD
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
Procedure/Part name
Nut
Notch
Washer
Damper
Bolt
Plate
Mirror
Packing
Q’ty
1
1
2
1
4
2
2
2
Service points
Reverse the removal steps for installation.
8-22
HULL
HOOD
STEERING MASTER COVER
E
STEERING MASTER COVER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
STEERING MASTER COVER
REMOVAL
Handlebar assembly
Fuel cock
Choke knob
Bolt
Shift lever handle
Nut/washer
Bolt
Bolt
Steering master cover
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “HANDLEBAR”.
Refer to “FUEL COCK AND FUEL FILTER”
in chapter 4.
Refer to “CHOKE CABLE” in chapter 4.
2
1
2/2
2
2
1
Reverse the removal steps for installation.
8-23
HULL
HOOD
HOSES
E
HOSES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
HOSES REMOVAL
Steering master cover
Band
Ventilation hose
Screw
Ventilation duct
Band
Check valve
Q’ty
2
2
4
1
1
1
8-24
Service points
Follow the left “Step” for removal.
Refer to “STEERING MASTER COVER”.
HULL
HOOD
HOSES
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
Procedure/Part name
Oil tank breather hose
Fuel tank breather hose
Clamp/pilot water hose
Nut/washer
Pilot water outlet
Packing
Q’ty
1
2
2/2
2/2
2
2
Service points
Reverse the removal steps for installation.
8-25
HULL
HOOD
HOSES
E
SERVICE POINTS
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
●
8-26
HULL
HOOD
SHIFT LEVER
E
SHIFT LEVER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
Procedure/Part name
SHIFT LEVER REMOVAL
Steering master cover
Shift cable
Ventilation duct
Bolt
Washer
Shift lever
Q’ty
1
1
1
8-27
Service points
Follow the left “Step” for removal.
Refer to “STEERING MASTER COVER”.
Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
Refer to “HOSES”.
Mark its original position
HULL
HOOD
SHIFT LEVER
E
SHIFT LEVER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
4
5
6
7
8
Procedure/Part name
Screw
Base assembly
Nut/washer
Screw
Plate
Q’ty
3
1
3/3
3
1
Service points
Reverse the removal steps for installation.
8-28
HULL
HOOD
SHIFT LEVER
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
BASE DISASSEMBLY
Bolt/washer
Plate
Spring
Actuator
Roller
Shaft
Shift arm
Q’ty
Service points
Follow the left “Step” for disassembly.
2/2
1
1
1
1
1
1
Reverse the disassembly steps for
assembly.
8-29
HULL
HOOD
SHIFT LEVER
E
SERVICE POINTS
Base assembly
1. Install:
● Shift arm
● Shaft
Installation steps:
Install the shift arm 1 so that it comes
in contact with the stopper 2 as
shown.
● Install the shaft 3 to the base so that it
come in contact with the stopper 4 as
shown.
●
8-30
HULL
HOOD
SEATS AND HAND GRIP
SEATS AND HAND GRIP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
SEATS AND HAND GRIP
REMOVAL
Rear seat assembly
Front seat assembly
Bolt
Seat lock assembly
Nut/washer
Notch
Bolt
Q’ty
1
1
4
2
4/5
2
2
8-31
Service points
Follow the left “Step” for removal.
E
HULL
HOOD
SEATS AND HAND GRIP
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
Procedure/Part name
Rear seat stay
Nut/washer
Front seat stay
Nut/washer
Bolt
Hand grip
Q’ty
1
4/4
2
4/4
4
1
Service points
Reverse the removal steps for installation.
8-32
HULL
HOOD
SEATS AND HAND GRIP
SERVICE POINTS
Seat lock inspection
1. Inspect:
● Front seat lock
● Rear seat lock
Damage/wear → Replace.
8-33
E
HULL
HOOD
EXHAUST SYSTEM
E
EXHAUST SYSTEM
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
EXHAUST SYSTEM REMOVAL
Hose clamp
Band
Rubber joint
Hose clamp
Rubber hose
Water lock
Hose clamp
Resonator assembly
Q’ty
2
1
1
2
1
1
1
1
8-34
Service points
Follow the left “Step” for removal.
Slide the water lock to back
Align mark with weld line
Mark a should be upside
HULL
HOOD
EXHAUST SYSTEM
E
EXPLODED DIAGRAM
Step
9
10
11
12
13
14
15
16
17
Procedure/Part name
Hose clamp
Rubber hose
Hose clamp
Water tank
Hose clamp
Rubber hose
Bolt
Exhaust outlet
Packing
Q’ty
1
1
1
1
1
1
Service points
Align hose parting line with tank mark
Align hose parting line with tank parting
line
3
1
1
Reverse the removal steps for installation.
8-35
HULL
HOOD
EXHAUST SYSTEM
E
SERVICE POINTS
Exhaust system inspection
1. Inspect:
● Water lock band
Cracks → Replace.
2. Inspect:
● Rubber hoses
Burns/cracks/damage → Replace.
3. Inspect:
● Water lock
Cracks/leaks → Replace.
Water → Drain.
4. Inspect:
● Resonator
● Water tank
Cracks/damage → Replace.
8-36
HULL
HOOD
DECK AND HULL
E
DECK AND HULL
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
DECK AND HULL DISASSEMBLY
Nut
Rope hole bolt
Nut/washer
Bow eye
Nut
Rope hole bolt
Nut
Spout
Nut
Q’ty
1
1
2/2
1
1
1
1
1
2
8-37
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
DECK AND HULL
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
16
17
18
Procedure/Part name
Plate
Cleat
Nut
Sponson
Spacer
Nut/washer
Screw/washer
Drain plug
Packing
Q’ty
1
1
8
2
8
4/4
4/4
2
2
Service points
Reverse the disassembly steps for
assembly.
8-38
HULL
HOOD
ENGINE MOUNT
E
ENGINE MOUNT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
ENGINE MOUNT REMOVAL
Engine assembly
Bolt
Damper 1
Damper 2
Bolt
Engine mount
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
6
1
1
8
4
Reverse the removal steps for installation.
8-39
HULL
HOOD
ENGINE MOUNT
E
HULL REPAIR
Shallow scratches
1. Sand the scratches with 400 grit sandpaper (either wet or dry) until the
scratches are smooth. Then, sand the
scratches once again with 600 grit sandpaper (either wet or dry).
Deep scratches
1. Remove any sharp or rough edges from
the hull surface.
2. Sand the scratches and a 1-inch circumference around them with 80 grit sandpaper (either wet or dry).
3. Clean the entire area with acetone and
let it completely dry.
4. Mix gel-coat and gel-coat thickener to
form a putty, and then add the catalyst
to the putty.
5. Apply the putty, spread it with a squeegee, and then cover the putty with wax
paper.
6. When the putty has set, sand it. Smooth
the area with 80 ~ 400 grit sandpaper
(either wet or dry) and a sanding block.
7. Clean the area with a dry cloth and then
polish it.
WARNING
Resins, catalysts, and solvents are flammable and toxic; only use them in a well-ventilated area and keep them away from open
flames and sparks. Always follow the manufacturer’s instructions and warnings.
8-40
HULL
HOOD
ENGINE MOUNT
E
Cracks and punctures
NOTE:
Before attempting to repair any cracks or
punctures, refer to “WATER VEHICLE FRP
REPAIR MANUAL”.
1. Remove any damaged fiberglass.
2. Cut the damaged area and separate it
approximately 0.25 inch.
3. On the outside of the hull, grind the
separated edge of the area to less than
5˚ as shown.
4. Working from inside the hull, grind the
damaged area approximately 4 inches
beyond the damage.
5. Clean the area with acetone, apply BP-1
or an equivalent primer onto both sides
of the damaged area, and then allow it
to cure for approximately 30 minutes.
6. Cover a piece of cardboard with wax
paper 1 and then cover the damaged
area with it.
7. Combine the polyester resin and the
catalyst, and then apply the mixture
onto the hull.
8. Install a glass mat 2 (2 inches smaller
than the ground area).
9. Apply the resin.
10. Install a 20 oz. fiberglass cloth 3 (1 inch
smaller than the glass mat).
11. Apply the resin.
12. Install another glass mat 4 (1 inch
smaller than the ground area).
13. When the resin has hardened remove
the piece of cardboard.
14. Finish the outer surface.
Refer to steps (3) ~ (7) in the “Deep
scratches” section.
8-41
HULL
HOOD
ENGINE MOUNT
E
Insert nut
NOTE:
Use the insert nut when:
● A pop nut which was attached to the hull
slipped off or,
● When a bolt which was fastened to an
insert nut or pop nut broke.
Part No.
Part
name
Remarks
EW2-62733-09
Nut
Stainless
steel, M6
●
●
●
Nut 1
Thread direction 2
Slot to be threaded 3
NOTE:
Drilling size
Material
Pilot hole diameter
FRP or SMC
9.1 ~ 9.2 mm (0.36 in)
Brass
9.4 mm (0.37 in)
Example 1:
NOTE:
Before attempting to install the insert nut,
refer to “WATER VEHICLE FRP REPAIR
MANUAL”.
The insert nut is used to repair the pop nut
designed for the ride plate.
(By repairing the FRP portion, the insert nut
can be used for all models.)
1. Remove:
● Pop nut
2. Clean the surface to be scarfed and the
inside of the hull with acetone.
3. Scarf the shaded portion of the hull.
8-42
HULL
HOOD
ENGINE MOUNT
E
4. First, apply tape 1 to the inner surface
of the hull and then laminate fiberglass
mats over the tape with resin.
NOTE:
When it is possible to work inside the hull,
laminate the mats from the inside.
5. Sand the outer surface of the hull until it
is smooth.
6. Install the ride plate.
7. Drill a 20 mm (0.79 in) deep hole in the
center of the laminated fiberglass layers
with a 9.2 mm (0.36 in) diameter drill
bit.
8. Pass the bolt 2 through the insert nut
and lock the bolt with the nut 3 as
shown.
9. Screw in the insert nut so that the top is
flush with the FRP surface.
10. Loosen the locknut and remove the
bolt.
CAUTION:
● Only
use a steel bolt with a tensile
strength of 8T or more.
● If the bolt is inferior in strength or is
made of stainless steel it may break.
Bolt 2
● Locknut 3
Example 2:
The brass insert nut, which is designed for
the Super Jet ride plate or the intake screen,
is used as follows.
●
NOTE:
If the bolt is broken, drill it out.
1. Drill a hole in the hull.
NOTE:
● First, use a small-diameter drill bit followed by drill bits of gradually increasing
diameter.
● Use a 9.4 mm (0.37 in) drill bit for the final
drilling.
8-43
HULL
HOOD
ENGINE MOUNT
E
2. To prevent water from entering the urethane foam, apply silicone sealant to
the inside of the hole as shown.
3. Install the insert nut as explained in
“Example 1”.
● Brass insert nut 1
● Hull 2
● Urethane foam 3
● Silicone sealant 4
Graphic removal
1. Hold a hair dryer approximately 1.5
inches above the graphic 1.
2. Apply heat to one corner of the graphic.
3. Slowly peel off the heated portion of the
graphic and continue working until you
reach the opposite corner and the entire
graphic is removed.
4. After the graphic is removed, clean the
entire bow area with isopropyl alcohol
to remove any residual adhesive.
Graphic installation
1. Mix 1 tablespoon of liquid detergent
and water in a 1-quart spray bottle.
2. Remove the backing from the new
graphic.
3. Spray the soap and water mixture onto
both sides of the graphic, and also onto
the hull area where the graphic will be
installed.
NOTE:
Spraying the front of the graphic with the
soap and water mixture will protect it from
being scratched during installation.
4. Align the graphic onto the fitting area of
the hull and position it with a squeegee.
NOTE:
Be sure to remove any air bubbles from the
graphic with the squeegee. Work from the
top of the graphic down and slide the
squeegee outwards from the graphic’s center line.
5. Allow the graphic to dry before waxing
or using the water vehicle.
8-44
TRBL
ANLS
E
CHAPTER 9
TROUBLE-ANALYSIS
TROUBLE-ANALYSIS ..................................................................................... 9-1
TROUBLE-ANALYSIS CHART ................................................................. 9-1
1
2
3
4
5
6
7
8
9
TRBL
ANLS
TROUBLE-ANALYSIS
E
TROUBLE-ANALYSIS
NOTE:
The following items should be checked before the “Trouble-analysis” chart is consulted.
1. The battery is charged and its specified gravity is within specification.
2. There are no incorrect wiring connections.
3. Wiring connections are properly secured and not rusty.
4. The lock plate is attached to the engine stop lanyard switch.
5. Fuel is reaching the carburetors.
TROUBLE-ANALYSIS CHART
YPVS SERVOMOTOR DOES NOT MOVE
POOR BATTERY CHARGING
IRREGULAR WARNING INDICATION
Items to be checked
BILGE INCREASE
LOOSE STEERING
OVERHEATING
POOR PERFORMANCE
ENGINE WILL NOT STOP
ENGINE STALLS
ROUGH IDLING
ENGINE WILL NOT START
Problems
Items
FUEL SYSTEM
Fuel tank
Air vent hose
Fuel hose
Fuel filter
Fuel pump
Carburetors
Carburetor synchronization
Trolling speed
POWER UNIT
Spark plug(s)
Compression
Reed valves
Cylinder head gasket
Piston rings
Cylinder block
Seals
Crankcase
Pistons
Bearings
Bearing housing
Couplings
9-1
Reference
chapter
4
4
4
4
4
4
4
3
3
5
5
5
5
5
5
5
5
5
5
5
TRBL
ANLS
TROUBLE-ANALYSIS
YPVS SERVOMOTOR DOES NOT MOVE
POOR BATTERY CHARGING
IRREGULAR WARNING INDICATION
Items to be checked
BILGE INCREASE
LOOSE STEERING
OVERHEATING
POOR PERFORMANCE
ENGINE WILL NOT STOP
ENGINE STALLS
ROUGH IDLING
ENGINE WILL NOT START
Problems
E
Items
Rubber coupling
Pilot water hose
Water hose
Water passage
JET PUMP UNIT
Duct
Impeller
Intake screen
Bearings
Intake duct
Water inlet hose
Bilge hose
Bilge strainer
Bilge hose joint
Valve body
ELECTRICAL
CDI unit
Lighting coil
Pickup coil (Pulser coil)
Ignition coil
Rectifier/regulator
Electrical sender(s)
Starter relay, starter motor
YPVS unit
Battery
Fuse(s)
Wire harness, electrical coupler(s)
HULL AND HOOD
Steering master
Water lock
Exhaust hose
Muffler
Drain plugs
9-2
Reference
chapter
5
5
5
5
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
3
7
7
8
8
8
8
8
WIRING DIAGRAM
1
3
G
G
W/R
L
L
2
d e
4
B/O
B
B
B
E
D
C
B
f g
W/L
B
A
B
B/O
B/Y
W/R
B/O
Gy/B
Br
O
Gy/R
Gy
G
Gy/Y
B/W
W
B/O
B Br R
W/L
5
B/Y
B/O
B
B/O
G
G W/R
W
F
G
B/Y B/O
W
L M
Gy/Y
Gy
Gy
Gy/Y
G
G
Gy/B
Gy/B
N O
G
Gy/B
B/Y B/O
B/O
O
Gy/R
P Q
Gy/R
20
7
G
Gy/R
R
B
B
R S
B/O
19
O
O
T U
B/O
B/O
17
Br
Br
Br
Br
R
R
R/W
R/W
R/W
R
R
R/L
R/Y
R/W
l m
R/W
Y
B
8
R/W
Y
B
10
9
W B
R
W
B
B/O
p
q
B
Br
B
17
R/W
14
#2
B/W
Br
R
Br
R/Y
16
R
N
B/W
R
B
M
Br
S
R/Y
17
18
n o
Br
Z a
R
R
#3
B/W
B
R
B/Y
R
B
R
+ –
Br
B
B
Gy
B
15
B
R/L
b c
R/L
B
12
Gy
B
13
B
B
B
B
B
A
B
G
W/R
C
W/R
G
B/Y
B/O
D
Gy
E
Gy/B
Br
B/W
B
Gy/Y
O
G
F
J
I
H
L
K
M
G
G
B/O
B
N
O
W/R
Gy/R
G
B/O
G
G
G
B/Y
R
S
T
U
B/O
O
G
a
Gy
Gy
G
Gy/R
b
R
B
c
B
Gy
n
R/Y
Br
L
R/L
Br
o
B/Y
O
q
Br
B/O
B/O
B/Y
f
L
B
W/L
B/O
B/O
g
O
h
B
V
W
Gy/B
B
O
G
R/W
Gy/R
Gy/Y
Gy/Y
W
W
Gy/Y
R/Y
W
Br
B
B
G
Gy/Y
Z
Y
W
B
Gy/R
j
i
Gy
X
Gy/B
R
R/B
L/R
W/L
m
l
k
L/R
L/B
Ch
Br
e
B/O
B
Gy
p
R
B/Y
Gy/R
d
B
R/L
Gy/B
Gy/B
B/O
B/O
B/Y
Br
Q
P
R
W
G
B/O
B
6
Lighting coil
Pickup coil
CDI unit
Oil level sensor
Fuel level sensor
Buzzer
Multi-function meter
Speed sensor
Engine stop switch
Engine stop lanyard switch
Start switch
YPVS servomotor
Battery
Starter motor
Starter relay
Fuse
Ignition coil
Spark plug
Exhaust temperature sensor
Water temperature sensor
Rectifier/regulator
Ch
Br
W
X Y
#1
B/W
11
R Br
SET
PULL
R
B
R
W
B
R
18
j k
L/R
L/B
Gy/Y
B/Y
B/O
18
Gy/B
V W
R/Y
B/Y
R/B
Gy/R
R/W
G
R
h i
Gy/Y
Gy
J
K
H
I
G
21
B
O
B/O
1
2
3
4
5
6
7
8
9
0
A
B
C
D
E
F
G
H
I
J
K
B
R/W
R/W
L/B
Y
Y
B
B
Br
Ch
G
Gy
L
O
R
W
Y
B/O
B/W
B/Y
Gy/B
Gy/R
Gy/Y
L/B
L/R
R/B
R/L
R/W
R/Y
W/L
W/R
: Black
: Brown
: Chocolate
: Green
: Gray
: Blue
: Orange
: Red
: White
: Yellow
: Black/Orange
: Black/White
: Black/Yellow
: Gray/Black
: Gray/Red
: Gray/Yellow
: Blue/Black
: Blue/Red
: Red/Black
: Red/Blue
: Red/White
: Red/Yellow
: White/Blue
: White/Red
YAMAHA MOTOR CO., LTD.
Printed in USA
Mar. 1999 – ?.? × 1 CR
(XA1200X)
Printed on recycled paper