Release Notes for Cisco IOS Release 12.0(5)T Feature Packs for the Cisco 802 IDSL and 804 IDSL Routers January 10, 2000 These release notes describe the Cisco IOS Release 12.0(5)T feature packs for Cisco 802 IDSL and Cisco 804 IDSL routers and contain the following topics: • Introduction, page 2 • System Requirements, page 2 • Installation Notes, page 9 • Related Documentation, page 13 • Service and Support, page 18 • Cisco Connection Online, page 20 • Documentation CD-ROM, page 20 Note The term ISDN represents an Integrated Services Digital Network (ISDN). The term IDSL represents an ISDN digital subscriber line (IDSL). Note Cisco 802 IDSL and Cisco 804 IDSL routers require Cisco IOS release 12.0(5)T software or above. In addition, the software images described in these release notes support the Cisco 802 IDSL and Cisco 804 IDSL routers only; they do not support the Cisco 801–804 routers or the Cisco 805 router. Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 2000. Cisco Systems, Inc. All rights reserved. Introduction Introduction How to Use These Release Notes The tables in these release notes contain details about the Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router: 1. Use Table 1, “Cisco 802 IDSL and Cisco 804 IDSL Router Default Memory and Upgrade Options,” for the feature set memory requirements, factory-default memory, and available memory upgrades for your router. 2. Use Table 3, “Feature Pack Product Numbers Quick-Reference List,” to identify the software image you want to load. 3. Use Table 4, “Cisco 802 IDSL and Cisco 804 IDSL Router Feature Packs,” to identify your feature pack and the memory required for your feature set, based on the image you load. 4. Use the tables in the “Feature Set Tables” section on page 5 to identify which features are supported in a feature set image. Feature Pack Components A feature pack is a box that typically contains the following items: • A CD-ROM with the following software: – Cisco IOS feature set software images that can include bundled modem firmware. – Router Software Loader (RSL) program (a Windows 95 application) that loads images onto your router. – Trivial File Transfer Protocol (TFTP) server application (for Windows 95 only). • Getting Started with the Router Software Loader. Note Before running RSL, see the “Alternatives to RSL” section on page 10. If you cannot use RSL to load images, you can follow the instructions in the “Alternatives to RSL” section on page 10. • Release notes (this document). • Other configuration or command references, if available. • Software license for using Cisco software in object code form on a single access server or router. • Documentation CD-ROM that contains all Cisco documentation. System Requirements This section describes the following topics: • Memory Defaults and Upgrade Options, page 3 • Hardware Supported, page 3 • Software Compatibility, page 4 Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 2 78-10444-01 System Requirements • Determining Your Software Release, page 4 • Updating Your Software Release, page 4 • Product Numbers Quick-Reference List, page 4 • Feature Pack Overview Table, page 5 • Feature Set Tables, page 5 Memory Defaults and Upgrade Options Table 1 Cisco 802 IDSL and Cisco 804 IDSL Router Default Memory and Upgrade Options Memory Type Cisco 802 IDSL & 804 IDSL Defaults Upgrade Options Flash memory card 8 MB 4-MB to 8-MB upgrade: MEM800-4U8F 8-MB to 12-MB upgrade: MEM800-8U12F DRAM 4 MB 4-MB to 8-MB upgrade: MEM800-4U8D 4-MB to 12-MB upgrade: MEM800-4U12D Hardware Supported The following hardware is supported: • Cisco 802 IDSL • Cisco 804 IDSL Table 2 summarizes the Cisco 802 IDSL and 804 IDSL routers and the ports that each model offers. Table 2 Cisco 802 IDSL and 804 IDSL Series Router Ports Router Ethernet Ports ISDN Ports Console Ports Cisco 802 One 10BaseT (RJ-45) ISDN BRI U, integrated Network Termination 1 (NT-1) (RJ-45) RJ-45 Cisco 804 Four-port 10BaseT (RJ-45) hub ISDN BRI U, integrated NT-1 (RJ-45) RJ-45 The Cisco 802 IDSL and 804 IDSL routers provide the following key hardware features: • Flash memory: the default is 8 MB, expandable to 12 MB. • Dynamic RAM: the default is 4 MB, expandable to 12 MB. • Color-coded ports and cable reduce the chance of cabling errors. • Routers can be stacked or mounted on a wall. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 3 System Requirements Software Compatibility The feature packs described in these release notes contain Cisco IOS Release 12.0(5)T software images, some images from previous software releases, and RSL Version 7.9. Determining Your Software Release To determine the version of Cisco IOS software running on your Cisco 802 IDSL or Cisco 804 IDSL router, log in to the router, and enter the show version user EXEC command. router> show version Cisco Internetwork Operating System Software IOS (tm) c800 Software (c800-y6-mw), Version 12.0(5)T, RELEASE SOFTWARE Updating Your Software Release For information on upgrading to a new software release, see the product bulletin Cisco IOS Software Release 12.0 T Upgrade Paths and Packaging Simplification (#819: 1/99) on CCO at: Service & Support: Software Center: Product Information: Product Bulletins: Software: Cisco IOS 12.0: Cisco IOS Software Release 12.0T Upgrade - No. 819 Product Numbers Quick-Reference List Table 3 Feature Pack Product Numbers Quick-Reference List Product Number Feature Pack Description CD08-IC-12.0.5T= Cisco 800 Series Internet DSL Feature Pack CD08-ICHL-12.0.5T= Cisco 800 Series Internet DSL FW IPSec Feature Pack CD08-IBHL-12.0.5T= Cisco 800 Series Internet DSL IPX FW IPSec Feature Pack Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 4 78-10444-01 System Requirements Feature Pack Overview Table Table 4 Cisco 802 IDSL and Cisco 804 IDSL Router Feature Packs Image Name (UNIX) Image Name (DOS) Flash Memory Required Main Memory Required RSL Installer Description Product Number CD-ROM Title CD08-IC-12.0.5T= Cisco 800 Series c800-y6-mw Internet DSL Feature Pack aaa1164 8 MB 4 MB Cisco 800 Series Internet DSL Feature Pack 12.05.T CD08-ICHL-12.0.5T= Cisco 800 Series c800-osy656i-mw Internet DSL FW IPSec Feature Pack aaa1165 8 MB 8 MB Cisco 800 Series Internet DSL, FW, IPSec Feature Pack 12.05.T CD08-IBHL-12.0.5T= Cisco 800 Series c800-nosy656i-mw Internet DSL IPX FW IPSec Feature Pack aaa1166 8 MB 8 MB Cisco 800 Series Internet DSL, IPX,FW, IPSec Feature Pack 12.05.T Feature Set Tables The Cisco IOS software is packaged in feature sets consisting of software images—depending on the platform. Each feature set contains a specific set of Cisco IOS features. Release 12.0 T supports the same feature sets as Release 12.0, but Release 12.0 T can include new features supported by the Cisco 802 IDSL and 804 IDSL routers. Table 5 Feature Sets Supported by the Cisco 802 IDSL and 804 IDSL Routers Feature Sets Image Names Feature Set Matrix Term Software Image Platforms In1 IP Feature Sets Internet DSL Basic2 c800-y6-mw Cisco 802 IDSL Cisco 804 IDSL (5) Internet DSL/FW/IPSec56 Basic, IPSec 563 c800-osy656i-mw Cisco 802 IDSL Cisco 804 IDSL (5) c800-nosy656i-mw Cisco 802 IDSL Cisco 804 IDSL (5) Internet DSL/IPX/FW/ IPSec56 Basic, IPSec 56 1. The number in the “In” column indicates the Cisco IOS release when the image was first introduced. For example, (5) means an image was introduced in Release 12.0(5)T. If a cell in this column is empty, the interface was included in the initial base release. 2. This feature set is offered in the basic feature set. 3. This feature set is offered in the encryption feature sets, which consist of IPSec 56-bit (Plus IPSec 56) data encryption feature sets. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 5 System Requirements Caution Cisco IOS images with strong encryption (including, but not limited to 168-bit (3DES) data encryption feature sets) are subject to United States government export controls and have limited distribution. Strong encryption images to be installed outside the United States may require an export license. Customer orders may be denied or subject to delay due to United States government regulations. When applicable, the purchaser or the user must obtain local import and use authorizations for all encryption strengths. Contact your sales representative or distributor for more information, or send an e-mail to export@cisco.com. Table 6 lists the features and feature sets supported by the Cisco 800 routers in Cisco IOS Release 12.0(5)T and uses the following conventions: Note • Yes—The feature is supported in the software image. • No—The feature is not supported in the software image. • In—The number in the “In” column indicates the Cisco IOS release in which the feature was introduced. For example, (5) means a feature was introduced in Release 12.0(5)T. If a cell in this column is empty, the feature was included in the initial base release. The feature set table only contains a selected list of features. The table is not cumulative—nor does it list all the features in each image. Table 6 Feature List by Feature Set for the Cisco 802 IDSL and 804 IDSL Routers Feature Set Internet DSL Internet DSL/FW/ IPSec56 Internet DSL/IPX/FW/ IPSec56 No No No Extended Access Control Lists Yes Yes Yes Full NAT (including one-to-one, many-to-many, & many-to-one) Yes Yes Yes GRE Tunneling No No No Local Password Yes Yes Yes MS-CHAP No No No PAP, CHAP Yes Yes Yes Route and Router Authentication No No No Static Translation Yes Yes Yes Token Card Authentication Yes Yes Yes Features In Analog Telephone Features Basic & Supplementary Features Basic Security Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 6 78-10444-01 System Requirements Table 6 Feature List by Feature Set for the Cisco 802 IDSL and 804 IDSL Routers (continued) Feature Set In Internet DSL Internet DSL/FW/ IPSec56 Internet DSL/IPX/FW/ IPSec56 (3) No No No Cisco Fast Step Equivalent No No No Configuration Express Yes Yes Yes Yes Yes Yes IPCP including Address Negotiations Yes Yes Yes TFTP Client /Server Yes Yes Yes Features Ease of Use & Deployment Auto SPID/SWITCH Connection DHCP Server (3) Enhanced Security IOS Firewall Including: Context Based Access Control Lists/Stateful Inspection (5) No Yes Yes Denial of Service Detection (5) No Yes Yes Java Blocking (5) No Yes Yes Real time alerts (5) No Yes Yes IPSec Encryption w/ 56bit DES (5) No Yes Yes L2TP (5) No Yes Yes Filtering Yes Yes Yes IP Yes Yes Yes IPX WAN No No Yes NetBIOS Access Lists, Name Caching Yes Yes Yes Transparent Bridging (including Spanning Tree) Yes Yes Yes No No No Yes Yes Yes Interactive (IOS) Debug Yes Yes Yes Interface Statistics Yes Yes Yes Loopback Testing Yes Yes Yes Monitor Tool Yes Yes Yes Performance History Yes Yes Yes SNTP No No No SNMP Read & Write (set & read MIB's) No No No LAN Management BootP Server DHCP/BootP Relay (3) Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 7 System Requirements Table 6 Feature List by Feature Set for the Cisco 802 IDSL and 804 IDSL Routers (continued) Feature Set Internet DSL Internet DSL/FW/ IPSec56 Internet DSL/IPX/FW/ IPSec56 SNMP Read only Yes Yes Yes Syslog No No No TACACS+ No No No Telnet, Console Port Yes Yes Yes User programmable Menu System No No No IP Enhanced IGRP No No No IP Multicast (relay only) No No No IP-Policy Routing No No No IPX WAN No No Yes RIP Yes Yes Yes RIPv2, Yes Yes Yes Triggered RIP Yes Yes Yes Frame Relay (Leased Line Only) Yes Yes Yes HDLC Yes Yes Yes IDSL Yes Yes Yes ISDN No No No ISDN Lease Line Yes Yes Yes ML-PPP Yes Yes Yes PPP Yes Yes Yes Selectable settings up to 144Kbps Yes Yes Yes Virtual Templates No No No AO/DI No No No Bandwidth on Demand No No No Dial on Demand Routing No No No Fair Queuing Yes Yes Yes IPX & SPX Spoofing No No Yes ISDN Caller ID Call-back No No No Snapshot Routing No No No Stac Compression Yes Yes Yes Weighted Fair Queuing No No No X.25 over D Channel No No No Features In Routing WAN WAN Optimization Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 8 78-10444-01 Installation Notes Installation Notes This section describes the following topics: • Image Installation Tips and Troubleshooting When Using RSL, page 9 • Alternatives to RSL, page 10 Image Installation Tips and Troubleshooting When Using RSL Image Installation Tips The following information about RSL operations can help you with the installation process: • If you are loading software on a preconfigured router, save the router configuration file on your PC before running RSL. • If you have added any static entries to the PC Address Resolution Protocol (ARP) table, one or more of them may be deleted by RSL. Manually re-enter any deleted entries in the PC ARP table. • During a connection, if the router’s running configuration is not the same as its startup configuration, the exact configuration is not restored. Any changes that you made since the last time you entered copy running-config startup-config or write memory commands are lost. • RSL restores the router’s startup configuration, but some running configuration commands are not restored. To restore the exact running configuration, reboot the router. The following interface configuration commands are not restored to the running configuration: – no shutdown – no ringspeed – media-type aui Recovering from a Connection Error If any of the following elements apply to your installation, modify the Short Timeout value from the Options dialog box in RSL: • You are connecting to a router or access server that has a large configuration file. • You are connecting to a Cisco AS5200 access server. • You see the following error message: "Failed to configure the router to enable the Cisco IOS software image and configuration file upload and download operations. You may want to check the router to make sure that the selected interface exists." If you are connecting to a Cisco AS5200, increase the Short Timeout value to 60 seconds. The Cisco AS5200 requires up to 45 seconds to write a configuration to nonvolatile random-access memory (NVRAM) due to the number of interfaces the it must check during this process. If you are connecting to any other router or access server, increase the Short Timeout to a value over 25 seconds. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 9 Installation Notes Note If you change the timeout value, you must do so before connecting to the router, or the new value will not be used. Also, increasing the Short Timeout value can increase the time it takes for RSL to connect to the target router. Restoring the Startup Configuration In some cases, RSL is unable to restore the startup configuration. If this happens, follow these steps: Step 1 Ensure that all cables are properly attached to both the router and the PC. Step 2 Restart RSL and connect by using the Preconfigured router option. Step 3 When asked if you want to overwrite the existing startup configuration file, choose no. Step 4 When asked if you want to continue, choose yes. Step 5 When the router is connected, select Download Router Configuration in the Router Software Loader dialog box. Step 6 Select the appropriate file and click the radio button beside Copy configuration to the router nonvolatile memory. The router should now contain the startup configuration it had before the initial RSL connection. Step 7 Exit RSL. Note In the steps above, the router configuration register (config-register 0xnnnn) is not restored. Note If you press Ctrl-Alt-Delete to quit RSL, the router configuration and the configuration register are not restored. However, the configuration file is not deleted from the PC. To restore the configuration file, follow the steps above, beginning with Step 2. Alternatives to RSL RSL is designed to work with a PC running Microsoft Windows 95 and is the recommended method for downloading software to the router; however, two alternatives are available for installing router software: Note • Installing the Router Software by Using the Console • Installing the Router Software by Using a TFTP Server Application The sample prompts and output shown in the following sections may not be identical to the prompts displayed on the router console. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 10 78-10444-01 Installation Notes Installing the Router Software by Using the Console This section explains how to use the copy xmodem flash command to install the router software from the CD-ROM onto the router. The following example shows how to use the copy xmodem flash command on a Cisco 802 IDSL or Cisco 804 IDSL router: Router# copy xmodem flash **** WARNING **** x/ymodem is a slow transfer protocol limited to the current speed settings of the auxiliary/console ports. The use of the auxilary port for this download is strongly recommended. During the course of the download no exec input/output will be available. ---- ******* ---Proceed? [confirm] yes Use crc block checksumming? [confirm] yes Max Retry Count [10]: Perform image validation checks? [confirm] yes Xmodem download using crc checksumming with image validation Continue? [confirm] yes Partition Size Used Free Bank-Size State Copy Mode 1 4096K 3259K 836K 4096K Read/Write Direct 2 4096K 0K 4095K 4096K Read/Write Direct [Type ?<no> for partition directory; ? for full directory; q to abort] Which partition? [default = 1] 2 System flash directory, partition 2: File Length Name/status 1 68 TESTFILE [132 bytes used, 4194172 available, 4194304 total] Destination file name? c800-y6-mw.120-5T Erase flash device before writing? [confirm] yes Flash contains files. Are you sure you want to erase? [confirm] yes Copy '' from server as 'c800-y6-mw.120-5T' into Flash WITH erase? [yes/no] yes Erasing device... eeeeeeeeeeeeeeee ...erased Ready to receive file...........C Verifying checksum... OK (0x5DE8) Flash device copy took 00:12:06 [hh:mm:ss] Installing the Router Software by Using a TFTP Server Application Use this TFTP server application method as an alternative method to install the router software from the CD-ROM. You can perform this procedure by using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the router software to the router. First, obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. If you are using a PC running Windows 95, you can use RSL or the TFTP server included on the feature pack CD-ROM to install the router software. For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or as shareware on the World Wide Web. Note To use an rcp application, follow the same procedure below, but substitute “rcp” for “TFTP” and use the copy rcp flash command instead of the copy tftp flash command. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 11 Installation Notes Step 1 Install any TFTP server application on the PC. (A PC application is included on the feature pack CD-ROM for Microsoft Windows 95 only.) Step 2 Start the TFTP server application on the PC by double-clicking the application icon or its .exe filename. Step 3 Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility. Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, select Settings to display a panel. To configure the local PC as a server, select the Server checkbox. Select a root directory where the Cisco IOS files reside (for example, d:\cpswinst\images). Caution Step 4 Make sure you set up your local PC as a TFTP server. If you do not, you cannot perform the copy procedure. This caution applies to both TFTP and rcp. Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router by using one of these methods: • Connect the PC com port to the router console port. This is the recommended method. When you reload the router with the new image in Step 10, you remain connected to the router. • Caution Step 5 Make sure that your PC is set up to communicate with the connected device through its network port. Connect your PC’s LAN port to the corresponding LAN port on the router. If you are making a direct connection to the router via Ethernet or Fast Ethernet, use an Ethernet crossover cable. If connecting to the router via an Ethernet or Fast Ethernet hub or Token Ring MAU (hub), use straight-through cable. Note Step 6 Establish a Telnet session from the PC to the router. If you choose to use Telnet, your connection to the router will be lost when it is reloaded. We recommend that you back up the router configuration before upgrading the router software. At the prompt, enter the IP address of your PC, as shown in the following example: Address or name of remote host [255.255.255.255]? 131.108.1.1 This is the IP address of your local PC, not that of the router. Step 7 At the prompt, enter the filename of the Cisco IOS Release 12.0 image to be copied to the router, as shown in the following example: Source file name? aaa1164.bin This example specifies the DOS image name of the IP feature set for Cisco 802 IDSL and Cisco 804 IDSL routers (as shown in Table 4 in the “Feature Pack Overview Table” section on page 5). Step 8 At the prompt, enter the destination UNIX image filename and press Enter. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 12 78-10444-01 Related Documentation This is the name of the image file on the router—not the full pathname of the image on the CD-ROM attached to the PC. Refer to Table 4 in the “Feature Pack Overview Table” section on page 5 for the UNIX image filename. Destination file name [aaa1164.bin]? c800-y6-mw During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it. Step 9 At the prompt, enter yes if you want to erase the existing image copy resident in the router Flash memory before copying the new one. Erase flash device before writing? [confirm] yes The entire copying process takes several minutes and differs from network to network. The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory. Step 10 Enter the reload command to reload the router: Router# reload After the reload is complete, the router should be running the required Cisco IOS image. Use the show version command to verify it. Related Documentation The following sections describe the documentation available for the Cisco 802 IDSL and 804 IDSL routers. These documents consist of hardware and software installation guides, Cisco IOS configuration and command references, system error messages, feature modules, and other documents. Documentation is available as printed manuals or electronic documents, except for feature modules, which are available online on CCO and the Documentation CD-ROM. Use these release notes with the documents listed in the following sections: • Release-Specific Documents, page 13 • Platform-Specific Documents, page 14 • Feature Modules, page 15 • Cisco IOS Software Documentation Set, page 15 Release-Specific Documents The following documents are specific to Release 12.0. They are located on CCO and the Documentation CD-ROM: • Release Notes for Cisco IOS Release 12.0 – To reach the Cross-Platform Release Notes for Cisco IOS Release 12.0 from CCO, click on this path (under the heading Service & Support): Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 13 Related Documentation – To reach the Cross-Platform Release Notes for Cisco IOS Release 12.0 on the Documentation CD-ROM, click on this path: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes • Product bulletins, field notices, and other release-specific documents To reach these documents from CCO, click on this path (under the heading Service & Support): Technical Documents: Product Bulletins • Caveats for Cisco IOS Release 12.0 T See the Caveats for Cisco IOS Release 12.0 and Caveats for Cisco IOS Release 12.0 T documents, which contains caveats applicable to all platforms for all maintenance releases of Release 12.0. – To reach the caveats document from CCO, click on this path (under the heading Service & Support): Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Caveats – To reach the caveats document on the Documentation CD-ROM, click on this path: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Caveats Note If you have an account with CCO, you can use Bug Navigator II to find caveats of any severity for any release. You can reach Bug Navigator II on CCO at Software Center: Cisco IOS Software: BUG TOOLKIT: Cisco Bug Navigator II, or at http://www.cisco.com/support/bugtools/bugtool.shtml. Platform-Specific Documents These documents are available for the Cisco 802 IDSL and 804 IDSL routers on CCO and the Documentation CD-ROM. • Cisco 800 Series Routers Hardware Installation Guide • Quick Start Guide — Setting up Cisco 800 Series Routers • Regulatory Compliance and Safety Info For Cisco 800 Series • Cisco 800 Series Routers Software Configuration Guide • Cisco 800 Fast Step Quick Start Guide • Upgrading Memory in the Cisco 800 Series Routers • Release Notes for Cisco 800 Series Routers To reach Cisco Cisco 800 Series documentation from CCO, click on this path (under the heading Service & Support): Technical Documents: Documentation Home Page: Access Servers and Access Routers: Fixed Access Routers: Cisco 800 series To reach Cisco Cisco 800 Series documentation on the Documentation CD-ROM, click on this path: Cisco Product Documentation: Access Servers and Access Routers: Fixed Access Routers: Cisco 800 series Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 14 78-10444-01 Related Documentation Feature Modules Feature modules describe new features supported by Release 12.0 T and are updates to the Cisco IOS documentation set. A feature module consists of a brief overview of the feature, benefits, configuration tasks, and a command reference. As updates, the feature modules are available online only. Feature module information is incorporated in the next printing of the Cisco IOS documentation set. To reach the feature modules from CCO, click on this path (under the heading Service & Support): Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation To reach the feature modules on the Documentation CD-ROM, click on this path: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation Cisco IOS Software Documentation Set The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents that are shipped with your order in electronic form on the Documentation CD-ROM—unless you specifically ordered the printed versions. Documentation Modules Each module in the Cisco IOS documentation set consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, Cisco IOS software functionality, and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Use each configuration guide with its corresponding command reference. On CCO and the Documentation CD-ROM, two master hot-linked documents provide information for the Cisco IOS software documentation set. On CCO (under the heading Service & Support): Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Configuration Guides and Command References On the Documentation CD-ROM: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Configuration Guides and Command References Release 12.0 Documentation Set Table 7 describes the contents of the Cisco IOS Release 12.0 software documentation set, which is available in electronic form and in printed form upon request. Note You can find the most current Cisco IOS documentation on CCO and the Documentation CD-ROM. These electronic documents may contain updates and modifications made after the hard-copy documents were printed. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 15 Related Documentation On CCO at (under the heading Service & Support): Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0 On the Documentation CD-ROM at: Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.0 Table 7 Cisco IOS Software Release 12.0 Documentation Set Books Chapter Topics • Configuration Fundamentals Configuration Guide • Configuration Fundamentals Command Reference • Bridging and IBM Networking Configuration Guide • Bridging and IBM Networking Command Reference • Dial Solutions Configuration Guide • Dial Solutions Command Reference Configuration Fundamentals Overview Cisco IOS User Interfaces File Management System Management Transparent Bridging Source-Route Bridging Token Ring Inter-Switch Link Remote Source-Route Bridging DLSw+ STUN and BSTUN LLC2 and SDLC IBM Network Media Translation DSPU and SNA Service Point SNA Frame Relay Access Support APPN Cisco Database Connection NCIA Client/Server Topologies Cisco Mainframe Channel Connection Airline Product Set X.25 over ISDN Appletalk Remote Access Asynchronous Callback, DDR, PPP, SLIP Bandwidth Allocation Control Protocol ISDN Basic Rate Service ISDN Caller ID Callback PPP Callback for DDR Channelized E1 & T1 Dial Backup for Dialer Profiles Dial Backup Using Dialer Watch Dial Backup for Serial Lines Peer-to-Peer DDR with Dialer Profiles DialOut Dial-In Terminal Services Dial-on-Demand Routing (DDR) Dial Backup Dial-Out Modem Pooling Large-Scale Dial Solutions Cost-Control Solutions Virtual Private Dialup Networks Dial Business Solutions and Examples Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 16 78-10444-01 Related Documentation Table 7 Cisco IOS Software Release 12.0 Documentation Set (continued) Books • Cisco IOS Interface Configuration Guide • Cisco IOS Interface Command Reference • Network Protocols Configuration Guide, Part 1 • Network Protocols Command Reference, Part 1 • Network Protocols Configuration Guide, Part 2 • Network Protocols Command Reference, Part 2 • Network Protocols Configuration Guide, Part 3 • Network Protocols Command Reference, Part 3 • Security Configuration Guide • Security Command Reference • Cisco IOS Switching Services Configuration Guide • Cisco IOS Switching Services Command Reference • Wide-Area Networking Configuration Guide • Wide-Area Networking Command Reference • Voice, Video, and Home Applications Configuration Guide • Voice, Video, and Home Applications Command Reference Chapter Topics Interface Configuration Overview LAN Interfaces Logical Interfaces Serial Interfaces IP Overview IP Addressing and Services IP Routing Protocols AppleTalk Novell IPX Network Protocols Overview Apollo Domain Banyan VINES DECnet ISO CLNS XNS AAA Security Services Security Server Protocols Traffic Filtering and Firewalls IP Security and Encryption Passwords and Privileges Neighbor Router Authentication IP Security Options Switching Services Switching Paths for IP Networks Virtual LAN (VLAN) Switching and Routing Wide-Area Network Overview ATM Frame Relay SMDS X.25 and LAPB Voice over IP Voice over Frame Relay Voice over ATM Voice over HDLC Frame Relay-ATM Internetworking Synchronized Clocks Video Support Universal Broadband Features Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 17 Service and Support Table 7 Cisco IOS Software Release 12.0 Documentation Set (continued) Books Chapter Topics • Quality of Service Solutions Configuration Guide • Quality of Service Solutions Command Reference • Cisco IOS Software Command Summary • Dial Solutions Quick Configuration Guide • System Error Messages • Debug Command Reference Note Policy-Based Routing QoS Policy Propagation via BGP Committed Access Rate Weighted Fair Queueing Custom Queueing Priority Queueing Weighted Random Early Detection Scheduling Signaling RSVP Packet Drop Frame Relay Traffic Shaping Link Fragmentation RTP Header Compression Cisco Management Information Base (MIB) User Quick Reference is no longer published. For the latest list of MIBs supported by Cisco, see Cisco Network Management Toolkit on Cisco Connection Online. From CCO, click on the following path: Service & Support: Software Center: Network Mgmt Products: Cisco Network Management Toolkit: Cisco MIB. Service and Support For service and support for a product purchased from a reseller, contact the reseller, who offers a wide variety of Cisco service and support programs described in “Service and Support” of Cisco Information Packet that shipped with your product. Note If you purchased your product from a reseller, you can access CCO as a guest. CCO is Cisco Systems’ primary real-time support channel. Your reseller offers programs that include direct access to CCO services. For service and support for a product purchased directly from Cisco, use CCO. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 18 78-10444-01 Service and Support Software Configuration Tips on the Cisco Technical Assistance Center Home Page If you have a CCO login account, you can access the following URL, which contains links and tips on configuring your Cisco products: http://www.cisco.com/kobayashi/serv_tips.shtml This URL is subject to change without notice. If it changes, point your Web browser to CCO and click on this path: Products & Technologies: Products: Technical Tips. The following sections are provided from the Technical Tips page: • Access Dial Cookbook—Contains common configurations or recipes for configuring various access routes and dial technologies. • Field Notices—Notifies you of any critical issues regarding Cisco products and includes problem descriptions, safety or security issues, and hardware defects. • Frequently Asked Questions—Describes the most frequently asked technical questions about Cisco hardware and software. • Hardware—Provides technical tips related to specific hardware platforms. • Hot Tips—Describes popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC Fax-on-demand service. To reach Fax-on-demand and receive documents at your fax machine from the United States, call 888-50-CISCO (888-502-4726). From other areas, call 650-596-4408. • Internetworking Features—Lists tips on using Cisco IOS software features and services. • Sample Configurations—Provides actual configuration examples that are complete with topology and annotations. • Software Products—Contains Cisco IOS Software Bulletins, Cisco TCP/IP Suite 100, General Cisco IOS, Internet/Intranet Applications and Software, Network Management, Network Protection Software Tips, and WAN Switching Products and Software. • Special Collections—Lists other helpful documents, including Case Studies, References & Request for Comments (RFCs), and Security Advisories. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 19 Cisco Connection Online Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services. Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’s customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files. CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information. You can access CCO in the following ways: • WWW: http://www.cisco.com • WWW: http://www-europe.cisco.com • WWW: http://www-china.cisco.com • Telnet: cco.cisco.com • Modem: From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and connection rates up to 28.8 kbps. For a copy of CCO’s Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com. Note If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco’s Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com. Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com. If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 20 78-10444-01 Documentation CD-ROM This document is to be used in conjunction with the documents listed in the “Related Documentation” section on page 13. Access Registrar, AccessPath, Any to Any, AtmDirector, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems Capital, the Cisco Systems Capital logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, the Cisco Technologies logo, ConnectWay, Fast Step, FireRunner, Follow Me Browsing, FormShare, GigaStack, IGX, Intelligence in the Optical Core, Internet Quotient, IP/VC, Kernel Proxy, MGX, MultiPath Data, MultiPath Voice, Natural Network Viewer, NetSonar, Network Registrar, the Networkers logo, Packet, PIX, Point and Click Internetworking, Policy Builder, Precept, ScriptShare, Secure Script, ServiceWay, Shop with Me, SlideCast, SMARTnet, SVX, The Cell, TrafficDirector, TransPath, ViewRunner, Virtual Loop Carrier System, Virtual Service Node, Virtual Voice Line, VisionWay, VlanDirector, Voice LAN, WaRP, Wavelength Router, Wavelength Router Protocol, WebViewer, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and ASIST, BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, the Cisco Systems Cisco Press logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, GeoTel, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any of its resellers. (9912R) Copyright © 2000, Cisco Systems, Inc. All rights reserved. Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 78-10444-01 21 Documentation CD-ROM Release Notes for Cisco IOS Release 12.0(5)T Feature Packs 22 78-10444-01