Samsung SCC-B5369N User manual

SCC-B5367
SCC-B5369
SCC-B5367S
SCC-B5369S
FRC
user manual
ENG
DIGITAL COLOR DOME
CAMERA
SPA-M
JAP
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsungsecurity.com
POR-B
imagine the possibilities
Safety information
6.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.
This exclamation point symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
7.
8.
9.
10
CA
1.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
• If this power supply is used at 240V ac, a suitable plug adapter should be used.
2.
WARNING
4.
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
5.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
3.
6.
7.
8.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
2 – DIGITAL COLOR DOME CAMERA
9.
S
Safety information
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on
top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify
this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or
attempted repair.)
10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
ENG
nt
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 140°F), low temperature (below -14°F), or high
humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or
damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
English – 3
Safety information
FCC Statement
W
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :
1.
1) This device may not cause harmful interference, and
2.
2) This device must accept any interference received including interference that may cause undesired operation.
3.
4.
Caution
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
5.
6.
7.
8.
9.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interference.Causing Equipment Regulations of ICES-003.
10
11
12
13
14
4 – DIGITAL COLOR DOME CAMERA
n.
ul
WARNING
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus
English – 5
ENG
e
Important Safety Instructions
Contents
Introduction
Features
Product & Accessories
Part Names and Functions
F
7
8
9
❖
❖
Installation
Before installation
Installation procedure
Adjusting the camera direction
12
12
14
❖
How to use OSD Menu
Using Icons in the Menu
Main Menu
Profile
Camera Setup
Intelligence
Privacy Zone Setup
Other Set
System Information
Language
❖
15
15
16
18
26
28
30
30
30
❖
❖
❖
❖
Specifications
Specifications
32
❖
❖
6 – DIGITAL COLOR DOME CAMERA
Introduction
FEATURES
❖ High Resolution
• This camera has realized high resolution of 600 lines using the top-notch full digital image processing and
special algorithm technologies.
❖ VPS(Virtual Progressive Scan)
• This is an advanced technology that reproduces a sharp progressive image. This is appropriate to high
quality recording and file transfer via the Internet.
❖ Intelligent Motion Detection & Tracking
• This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it
displays an alert if an object passes / enters /exits the virtual fence or virtual area.
❖ XDR (eXtended Dynamic Range)
• Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a
certain pixel unit to determine the optimal visibility.
❖ DAY/NIGHT
• This function can make the IR Cut filtering function inactive under the illumination below the normal value.
❖ High Sensitivity
• It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.
❖ Low Illumination
• It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera
identify objects even in the worst environment.
❖ Superior Backlight Adjustment
• When an object has a bright illumination or sunlight behind it, this camera automatically improves the
shaded object picture quality.
❖ Digital Power Synchronization
• The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the
operationability and reliability of this camera.
English – 7
ENG
❖ WDR
• WDR extends the contrast range as it takes a picture of each of dark and bright areas before compositing
the two, which is useful if you take a picture of windows inside a building. Namely, it improves the picture
quality of the outdoor scenery as well as indoor.
Introduction
❖ Output Signal Setting
• You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy,
Horizontal/Vertical profiling, and digital zooming.
❖ OSD(On Screen Display) Menu
• OSD menu is provided to display the status of camera and to configure the functions interactively.
❖ Coaxial Cable Communication
• This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the control
signal. In installation or repair, this helps you control the communication controller (optional) without additional cabling.
PRODUCT & ACCESSORIES
❖ Product & Accessories
• Main Product
Camera
• Accessories
Tab screw
Test Monitor Cable
User’s Manual
 Note :
– The test monitor cable is used to test the camera by connecting to a portable display. If you really want to connect the camera
to a monitoring display, use the BNC cable.
8 – DIGITAL COLOR DOME CAMERA
P
❖
Introduction
PART NAMES AND FUNCTIONS
❖ Components of your camera
Test
monitor
output
테스트
모니터
출력
g.
ENG
/N
T.D
EX
a
렌즈
Lens
GN
D
Power
connector
전원
커넥터
Video
비디오 connector
커넥터
English – 9
Introduction
No
Name
Brief description
1
Cover dome
2
Inner cover
Covers the main body to protect it.
3
Wing locker
Push a long thin screwdriver into its narrow spot and press it outward when you want to
remove the inner cover.
Covers the inner cover, lens, and main body to protect them.
4
Main body
5
Mount bracket
Used as a ceiling or wall fixture. It is fixed using three long tab screws provided in the
package.
Includes a lens, a switch board, a PCB board, screws, and such.
This passage is designed to make arrangement of the cables if you drill a hole to extend the wiring.
6
Wiring Passage
7
Zoom lever
Using this lever, the lens zoom can be adjusted and fixed.
8
Focus lever
The lens focus can be adjusted by rotating it left or right. Rotate it clockwise for fixing.
9
Tilt fixing screw
10
5-way Switch
This switch is used to set and adjust the settings of the camera’s functions.
11
Groove mark
To attach the Main body to the Mount bracket, align this groove mark on the Main body with
the wide groove in the CAMERA FRONT side on the Mount bracket.
12
Locker
13
Lock releaser
14
Cable
❖
Using this screw, the slope of the lens can be adjusted and fixed.
Used to open or close the Cover dome. To open the cover dome, press the locker.
Push it outward and rotate the main body in UNLOCK direction when you want to remove
the Mount bracket from the Main body or to remove the installed camera from the Mount
bracket.
Connect the Video connector to BNC cable and Power connector to power adapter.
EXT. D/N is a port for DAY/NIGHT conversion.
High(DC +3V ~ +5V): DAY(COLOR) Mode.
Low(0V): NIGHT (BW) Mode.
10 – DIGITAL COLOR DOME CAMERA
•
Introduction
❖ Setting switches
g.
ENG
th
• SETUP Switch
This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the
MAIN MENU appears.
ef (Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the
displayed value.
cd (Up/Down) : By pressing this switch up or down, you can move up or down on the menu.
‹ : When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press
this button.
English – 11
Installation
BEFORE INSTALLATION
❶
Before installing your camera, you have to read the following cautions.
❷
• You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
• Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it
may cause a breakdown or fire.
• When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
❹

INSTALLATION PROCEDURE
❸
❺
❻
❼
❽
❾
12 – DIGITAL COLOR DOME CAMERA
Installation
❶ Press the Locker button on the bottom of your camera and remove the Cover dome from the Main body
using the other hand. The Main body and Inner cover will be exposed to you.
❷ To install and adjust your camera, you have to first remove the Inner cover. To remove the Inner cover from
the Main body, push a long thin screwdriver into the narrow spot of the Wing locker and press it outward to
remove the cover.
❸ Remove the Mount bracket from the Main body by rotating the Main body in the UNLOCK direction while
pushing the Lock releaser outward. If it is not easily done, rotate the Mount bracket in the LOCK direction
while holding small holes on the Mount bracket.
❹ Fix the Mount bracket to the location (ceiling or wall) with supplied three screws.
ENG
 Note :
– The CAMERA FRONT sign on the Mount bracket should face the camera monitoring area.
❺ Extend the wiring up to the ceiling or wall through the bracket.
❻ Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after aligning the Groove
mark on the Main body with the wide groove around the CAMERA FRONT inlay.
❼ Adjust the camera direction. For more details on the direction control, see “Adjusting the camera direction,”
on the same page. When required to adjust the zoom and focus for your camera, see “Connecting cables
and changing the settings,” on page 10.
❽ Attach the Inner cover to the Main body by pressing it until a “click” sound is heard after aligning two screw
holes on the Wing lockers of the Inner cover with two screw holes on the Main body’s left and right sides.
❾ Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard after aligning the
bump inside the Cover dome with the Groove mark on the Main body.
English – 13
Installation
ADJUSTING THE CAMERA DIRECTION
U
When the camera is fixed on the ceiling, you can adjust the camera viewing angle. You can rotate your camera
leftward or rightward (Panning), and can change the slope of your camera upward or downward (Tilting).
•
In case of panning, the rotation limit of your camera is set to 355 degree (100 degree clockwise and 255 degree
counterclockwise). The rotation is stopped by the Stopper inside of the camera. For panning control, first
unfasten two screws located on the bottom and rotate in the direction you want, and then fasten them to fix the
camera.
Panning
In case of tilting, you can change the slope of your camera
from zero to 90 degree. However if the slope angle is
under 17 degree, you can encounter a partial image hide
problem. To fix the location after adjusting the tilting angle,
use the Tilt fixing screws.
To adjust the focus and zoom of your camera, use the
Zoom lever and Focus lever. When you install the camera
on the inclined ceiling or wall, you can rotate the camera
lens to see a correct direction image.
•
•
•
Tilting
Lens rotation
14 – DIGITAL COLOR DOME CAMERA
•
a
ee
he
How to use OSD Menu
USING ICONS IN THE MENU
• (EXIT)
Exits the menu setting.
Before you exits the menu setting, select SAVE to
save your settings, or select QUIT to cancel.
• (RET)
Returns to the previous menu.
MAIN MENU
ÃÃMAIN MENUÃÃ
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
OTHER SET
SYSTEM INFO
LANGUAGE
• (HOME)
Returns to the main menu.
• (SAVE)
• (DEL)
Used to deletes your settings of MASK AREA,
PRIVACY ZONE and more.
Once you delete your settings, they will not be
restored even if you select QUIT in the menu.
• PROFILE
You can set a mode according to the camera
installation conditions.
• CAMERA SET
Configure Camera related functions and data.
• INTELLIGENCE
You can configure the settings of motion
detection, tracking and more.
• PRIVACY ZONE
You can configure the privacy related settings.
• OTHER SET
You can configure for Factory Defaults, and more.
• SYSTEM INFO.
Displays the system information including the
camera version and communication settings.
• LANGUAGE
Select a preferred one from the supported
languages.
English – 15
ENG
Used to save your settings of MASK AREA,
PRIVACY ZONE and more.
Once you save your settings, they will remain
even if you select QUIT in the menu.
How to use OSD Menu
PROFILE
ePROFILEf
ÃSTANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
CUSTOM
D
W
In the PROFILE menu, you can configure the following camera settings at once.
CAMERA SET Menu
Previous
Sub-menus
Menu
VPS
IRIS
ALC
LENS
LEVEL
BACKLIGHT
WDR
WEIGHT
WDR LEVEL
WHITE BAL
MOTION
DNR
SHUTTER
SENS-UP
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
OFF
ALC
DC
0
OFF
User setting
allowed
User setting
allowed
User setting
allowed
(F.FAST)--MID
OFF
AUTOx4
ON
ALC
DC
0
OFF
User setting
allowed
User setting
allowed
User setting
allowed
(F.FAST)--MID
AUTO1/250
AUTOx2
OFF
ALC
DC
0
OFF
WDR
OFF
ALC
DC
0
OFF
User setting
allowed
User setting
allowed
User setting
allowed
(F.FAST)--MID
OFF
AUTOx4
OFF
ALC
DC
0
OFF
User setting
allowed
User setting
allowed
User setting
allowed
SLOW
MID
OFF
AUTOx4
16 – DIGITAL COLOR DOME CAMERA
MID
0
User setting
allowed
NORM
MID
OFF
AUTOx4
❖
❖
❖
❖
How to use OSD Menu
BRIGHTNESS
MODE
RED
BLUE
DETAIL
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
MID
AUTO
OFF
DAY
ATW2
0
0
User setting
allowed
OFF
User setting
allowed
User setting
allowed
2
MID
AUTO
ON
DAY/NIGHT
ATW1
0
0
-
MID
DAY
OFF
DAY
ATW1
0
0
User setting
allowed
OFF
User setting
allowed
User setting
allowed
2
MID
AUTO
OFF
DAY/NIGHT
ATW1
0
0
-
MID
DAY
OFF
DAY
ATW1
0
0
User setting
allowed
OFF
User setting
allowed
User setting
allowed
2
MID
ATW2
0
0
2
MID
ATW2
0
0
2
❖ ITS
It will be set automatically so you can easily check the traffic conditions.
❖ BACKLIGHT
It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.
❖ DAY/NIGHT
It will be set automatically so it optimizes to the day or night conditions, respectively.
❖ GAMING
It will be set automatically to help you take a picture in a regular indoor lighting condition.
English – 17
ENG
CAMERA SET Menu
Previous
Sub-menus
Menu
XDR
DAY/NIGHT
NIGHT
BURST
WHITE BAL
DAY
MODE
RED
BLUE
NIGHT
How to use OSD Menu
Setup the general functions of zoom camera module.
CAMERA SETUP
Use the cdef switch to select a menu item.
eCAMERA SETf
CAMERA ID
OFF
VPS
OFF
IRIS
ALC
MOTION
(F.FAST)--DNR
MID
SHUTTER
OFF
SENS-UP
AUTO X4
FLICKERLESS
OFF
XDR
MID
d
❖ CAMERA ID
‹CAMERA ID‹
ABCDEFGHIJKLMNOPQRSTUVWXYZ0
123456789 :?-+*()/
SPffeeSP LOCATION
CAMERA-1..................
...........................
c
DAY/NIGHT
AUTO
WHITE BAL
DIGITAL ZOOM
OFF
DETAIL
[2]
V-SYNC
(INT)--AGC COLOR SUP
LOW
REVERSE
H/V
POSI/NEGA
+
PIP
OFF
d
c
DIS
OFF
18 – DIGITAL COLOR DOME CAMERA
The CAMERA ID menu is used for you to assign
a unique name to a camera. If you press the
SETUP switch with the CAMERA ID menu
selected, you will see the appropriate screen.
You can enter up to 54 alphanumeric or
special characters for the CAMERA ID. Select
LOCATION and press the SETUP switch to
move the display position of the CAMERA ID.
❖ VPS
[OFF, ON]
If you set the VPS (Virtual Progressive Scan)
option, the camera will display the image in
progressive format.
❖ IRIS
[OFF, ON]
[ALC]
The IRIS menu is used if you want to adjust the
intensity of radiation incoming to the camera.
•
e.
• ALC (Automatic Light Control)
① If you press the SETUP switch with an ALCbased sub menu selected, you will see the
appropriate screen.
‹ALC‹
LEVEL
BACKLIGHT
[00]----I---OFF
If you use an ordinary camera in a scene
with an intensive backlight, the object will be
displayed dark on the monitor affected by the
backlight. To solve this problem, you can use
the BLC(Back Light Compensation) function
to improve the sharpness of the image in
such a high contrast scene.
③ If you set the BACKLIGHT option to WDR, you will
see a menu where you can set the WDR options.
You can adjust the shutter speed in WDR LEVEL
and the brightness in WEIGHT.
The LEVEL menu is used to adjust the
overall brightness, where “+” will increase the
brightness and “–” will decrease it.
② If you set the BACKLIGHT option to BLC,
you will see a menu where you can set the
BLC area.
you can set the desired BLC zone by defining
the size and location.
‹ALC‹
LEVEL
[00]----I---BACKLIGHT
BLC
AREA
USER
<SIZE>
<LOCATION>
You can also select any of OUTDOOR, and
INDOOR in WHITE BAL.
‹ALC‹
LENS
DC
LEVEL
[ 00]----I---BACKLIGHT
WDR
WEIGHT
MID
WDR LEVEL [ 0]----I---WHITE BAL
INDOOR
WDR(Wide Dynamic Range) extends the gain range of
the screen that is mostly useful if you take a simultaneous
picture of both indoor and outside of the window.
Namely, it improves the sharpness of the
picture in outdoor scenery as well as indoor.
 Note :
– If you use the VPS (Virtual Progressive Scan) function, the CCD
reads differently so you can not use WDR simultaneously.
If you set VPS to ON, WDR will be automatically set to OFF.
English – 19
ENG
n
How to use OSD Menu
How to use OSD Menu
❖ AGC
[OFF, VERY LOW, LOW, MID, HIGH, VERY
HIGH, USER, FIX]
The AGC (Auto Gain Control) menu is used to
set the AGC level of the camera. When the AGC
is active, the camera automatically increases the
sensitivity by amplifying the Video signal when
the strength of the signal falls below the normal
value.
If OFF or FIX mode is selected in the SENS-UP
menu, you can specify the AGC level.
If you press the SETUP switch with a USER
sub menu selected, you will see the appropriate
screen.
‹AGC USER‹
LEVEL

‹AGC FIX‹
LEVEL
[01]
❖
If you press the SETUP switch with a FIX sub
menu selected, you will see the appropriate screen.
As a fixed value of the AGC gain is used in FIX
mode, you can select one of the 16 detailed levels
from VERY LOW to VERY HIGH before fixing it.
FIX mode is not available if you set the
BACKLIGHT function to WDR.
[16]
 Note :
– If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the AGC menu will be deactivated.
– If FLICKERLESS is set to ON, the AGC FIX mode will be disabled.
In USER mode, you can break down the level in
16 steps from VERY LOW to VERY HIGH to your
preference.
❖ MOTION
[S.SLOW, SLOW, NORM, FAST, F.FAST]
The MOTION menu is used to adjust the strength
of the AGC level for a control of the camera motion.
This is available only if the SENS-UP menu is set
to AUTO.
You can select one from S.SLOW, SLOW, NORM,
FAST and F.FAST for the AGC level.
If you monitor a fast moving object in a low contrast
scene, select F.FAST while select S.SLOW for a
hardly moving object in the same lighting condition.
20 – DIGITAL COLOR DOME CAMERA
❖
n.
d.
ST]
n.
M,
st
 Note :
– If the DAY/NIGHT menu of the CAMERA SET is set to
AUTO, the MOTION menu will be deactivated.
❖ DNR
[OFF,LOW,MID,HIGH, USER(1~16)]
You can configure the DNR (Digital Noise
Reduction) related settings.
Reduces the noise on the screen.
This is especially useful for a severely distorted
screen.
You can set the level if you set DNR to USER.
❖ SHUTTER
[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250,
AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO
1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250,
1/500, 1/1000, 1/2000, 1/4000, 1/10K]
The SHUTTER menu is used to configure settings
of the fixed / auto high-speed electronic shutter.
You can select one of 7 options from 1/100(PAL:1/120)
to 1/10K for the fixed high speed electronic shutter,
which is mostly used for imaging a fast moving object.
The auto high speed electronic shutter operates
as the fixed high speed shutter in a high contrast
scene but automatically focuses the target if the
iris opens fully in a low contrast scene like in ELC
mode. When it gets brighter back, the mode will
switch to the fixed high speed electronic shutter
mode.
 Note :
– If the SENS-UP function is set to AUTO, only items of
OFF and AUTO are available in the SHUTTER menu.
– If the SENS-UP mode is set to FIX, the SHUTTER menu
will be deactivated.
– If the FLICKERLESS function is set to ON, the SHUTTER menu
will be deactivated.
❖ SENS-UP
[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO
X8, AUTO X12, AUTO X16, AUTO X24, AUTO
X32, AUTO X48, AUTO X64, AUTO X96, AUTO
X128, AUTO X256, AUTO X512, FIX X2, FIX
X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24,
FIX X32, FIX X48, FIX X64, FIX X96, FIX X128,
FIX X256, FIX X512]
Automatically detects the ambient level of
darkness in the dark or low contrast scene to
extend the accumulated time, keeping the image
bright and sharp; It can be also used as FIX mode.
 Note :
– If the SHUTTER menu is set to fixed electronic shutter
mode, the SENS-UP menu will not be available.
– If FLICKERLESS is set to ON, the FIX mode of the SENSUP menu will be disabled.
– If the SHUTTER menu is set to AUTO, the SENS-UP
menu can be set to either OFF or AUTO mode.
– If the BACKLIGHT function is set to WDR, the SENS-UP menu
can not be set to FIX.
However, the auto high speed shutter operates
properly only in a camera featuring a DC or VIDEO lens.
n.
English – 21
ENG
s
How to use OSD Menu
How to use OSD Menu
❖ FLICKERLESS
[OFF, ON]
If set to ON, the shutter speed will be fixed to
1/100(PAL:1/120) second. This will prevent possible screen
distortion due to a mismatch between the vertical sync
frequency and the blinking frequency of the lighting.
 Note :
– If the SHUTTER menu is set to AUTO or FIX mode, the
FLICKERLESS menu will not be available.
– If the SENS-UP function is set to FIX mode, the Flickerless
menu will be deactivated.
– If AGC is set to FIX mode, the FLICKERLESS function will
be disabled.
❖ XDR (eXtended Dynamic Range)
[OFF, LOW, MID, HIGH]
Actively controls the gamma compensation in the
way it operates the ambient luminance contrast
in a certain pixel unit to determine the optimal
visibility.
Select one from OFF, LOW, MID and HIGH.
Closing to HIGH will increase the compensation
level.
❖ DAY/NIGHT
[DAY,NIGHT,AUTO,EXT]
• DAY
If set to DAY, it will be fixed to DAY mode
regardless of the ambient conditions.
• NIGHT
If set to NIGHT, it will be fixed to Black-and-White
mode regardless of the ambient conditions.
22 – DIGITAL COLOR DOME CAMERA
If you press the SETUP switch with a NIGHT sub
menu selected, you will see a menu where you can
set Burst to OFF/ON.
If BURST is set to ON, the Burst signal will output
together with the black-and-white composite video
signal. If BURST is set to OFF, the Burst signal does
not output.
You can set the BURST option to OFF/ON, or
select to output the Burst signal in NIGHT mode.
• AUTO
The camera will automatically switch between
DAY and NIGHT mode, according to the lighting
condition.
If you press the SETUP switch with an AUTObased sub menu selected, you will see the
appropriate screen.
‹AUTO‹
BURST
DAYÆNIGHT
BRIGHTNESS
DWELL TIME
NIGHTÆDAY
BRIGHTNESS
DWELL TIME
MASK AREA
OFF
MID
2S
1
MID
5S
2
You can set the BURST option to OFF/ON, or
select to output the Burst signal in NIGHT mode.
The BRIGHTNESS of DAYÆNIGHT sets the
brightness degree of color to BW switching,
for which you can select from LOW, MID, and
es
e.
HIGH. As you adjust it from HIGH to LOW, the
screen switches to black and white mode under
the darker situation.
DWELL TIME of DAYÆNIGHT sets the time to
maintain switched black and white mode.
The BRIGHTNESS of NIGHTÆDAY sets the
brightness degree of BW to color switching, for
which you can select from LOW, MID, and HIGH.
As you adjust it from HIGH to LOW, the screen
switches to color mode under the darker situation.
DWELL TIME of NIGHTÆDAY sets the time to
maintain switched color mode.
The MASK AREA menu is used to prevent
unintended mode switching or inability of
determining the switching due to existence of
high spot light source at night.
If you press the SETUP switch in item 1 or 2 of
the MASK AREA menu, you will see a menu
where you can specify an area to MASK.
The MASK is only for determining the mode
switching, and any excessive bright area at night
will be excluded by the configured MASK.
 Note :
– If BACKLIGHT is set to BLC, the MASK AREA function will
be deactivated.
• EXT
This enables an auto switch between DAY and NIGHT
mode using the interface with the external sensor.
❖ WHITE BAL
• DAY
In DAY mode, you can set the color values of
RED and BLUE. The screen will be displayed in
colors according to your settings.
‹WHITE BAL‹
DAY/NIGHT
MODE
RED
BLUE
R-GAIN
B-GAIN
‹MASK AREA‹
<SIZE> <LOCATION>
[DAY/NIGHT]
If you want to adjust the color scheme, use the
WHITE BALANCE function.
DAY
AWC
[00]----I---[00]----I---[0248]
[0247]
You can specify MASK 1 and 2 simultaneously.
 Note :
– You can set the values of R-GAIN and B-GAIN only in
AWC mode.
English – 23
ENG
g
How to use OSD Menu
How to use OSD Menu
• NIGHT
Use the NIGHT mode if you want to set the white
balance differently according to the ambient
luminance.
If the NIGHT mode is set to OFF, the white
balance will always operate as set in DAY mode;
if not to OFF, the camera will switch to as set in
DAY/NIGHT mode according to the brightness.
In NIGHT mode, you can set the values of RED,
BLUE and BRIGHTNESS. The screen will be
displayed in colors according to your settings.
‹WHITE BAL‹
DAY/NIGHT
BRIGHTNESS
MODE
RED
BLUE
R-GAIN
B-GAIN
NIGHT
MID
AWC
[00]----I---[00]----I---[0248]
[0247]
 Note :
– You can set the values of R-GAIN and B-GAIN only in
AWC mode.
–
–
–
–
the ambient conditions. The color temperature
ranges from approx. 2500K to 9300K.
• ATW2: The color temperature ranges from
approx. 2,000K to 10,000K.
• AWC ( Auto White Balance Control): If you
press the SETUP switch in the appropriate item
position, Auto White Balance will perform once.
• 3200K : Set color temperature to 3200K
• 5600K : Set color temperature to 5600K
RED : Adjusts the strength of the red color.
BLUE : Adjusts the strength of the blue color.
R-GAIN/B-GAIN : Enables you to set the current
color temperature manually.
BRIGHTNESS : Select a brightness level in
switching from setting in DAY mode to setting in
NIGHT mode.
❖ DIGITAL ZOOM
-L
c
r
e

[ON/OFF]
You can set the digital zoom factor and position.
If you press the SETUP switch with the DIGITAL
ZOOM function set to ON, you will see the
appropriate screen.
❖
❖
When the zoom factor and position are defined,
the digital zoom function will operate.
– If AGC is set to OFF or FIX, you can not access the
NIGHT menu.
– For adjusting the white balance, the following
5 modes are provided:
• ATW1(Auto Tracing White Balance mode
1): The camera can automatically adjust the
color temperature in real time, according to
24 – DIGITAL COLOR DOME CAMERA

How to use OSD Menu
e
❖ AGC COLOR SUP
[LOW , MID, HIGH]
Adjust the color scheme according to the AGC
value.
‹DIGITAL ZOOM‹
RATIO
[X1.0]
< LOCATION > [OFF, H, V, H/V]
❖ REVERSE
Mirrors video signals horizontally, vertically, or
both.
m
e.
.
L
- LOCATION : If you press the SETUP switch in the
condition where the image is enlarged as much as the
ratio setting, you can watch an invisible area of the
effective screen as well using the cdef switch.
 Note :
– If the digital zoom factor is set to larger than 1x, the FENCE
function will be deactivated.
The DIGITAL ZOOM function enlarges the pixel itself, which can
cause deterioration of the quality.
❖ DETAIL
[0~3]
Controls the horizontal or vertical distinction.
❖ V-SYNC
[INT, LINE]
Select the vertical sync mode for INT or LINE.
If you select INT, the camera will use the internal
synchronization.
If selecting LINE, the camera will use the external
power source frequency for the synchronization.
You can adjust the LL-PHASE.
 Note :
– Use of DC 12V will fix V-SYNC to INT, which can not be
changed.
[+, -]
❖ POSI/NEGA
Output as it is or mirror the video brightness
signal.
[OFF, ON]
❖ PIP
Displays a sub image together with the main
image on the same screen using the Picture In
Picture function.
 Note :
– If more than one privacy zone is set and the PRIVACY
SET is set to ON, the PIP function will be deactivated.
– If the INTELLIGENCE function is set to FENCE mode, the
PIP menu will be deactivated.
❖ DIS
[OFF, ON]
Digital Image Stabilization will set the anti-shake
compensation.
 Note :
– If you set DIS to ON, the compensation area will be
enlarged as set in the digital zoom factor.
If you set the digital zoom factor to greater than the
enlarged zoom factor for the compensation, the DIS
function will be deactivated.
English – 25
ENG
t
How to use OSD Menu
• FENCE
INTELLIGENCE
eINTELLIGENCEf
MOTION
ADVANCED
MASK AREA
DISPLAY
SENSITIVITY
RESOLUTION
1
OFF
OFF
2 3 4
ON
[4]
[5]
You can set the motion detection and tracking in the
INTELLIGENCE menu.
❖ MOTION
‹FENCE‹
LINE
AREA
OFF
OFF
[OFF,TRACKING,DETECTION]
• TRACKING
Detects and tracks a moving object.
• DETECTION
Detects a moving object.
 Note :
– If it is set to DETECTION, you can not set such functions as
FIXED/MOVED and FENCE in the ADVANCED menu.
❖ ADVANCED
This is to detect if a moving object passes
through the specified LINE or AREA.
In a condition where a moving object is detected
in an analysis of the previous and current frames
whose movement overlaps a certain area, the
system displays “PASS” if the object’s center line
passes through the line while it displays “ENTER” or
“EXIT” if the center point passes through the area.
[OFF, FIXED/MOVED, FENCE]
Detects a motion of an object and displays an
image of any moving object before tracking the
moving route.
You can set the position and detection direction of the
LINE, and the size and position of the AREA.
- How to set the line
‹LINE‹
PIXEL LEVEL
<POINT>
DIRECTION
26 – DIGITAL COLOR DOME CAMERA
[4]
§¨
or
How to use OSD Menu
① If you press the SETUP switch with the LINE
option set to ON, you can specify the position
and detection direction of the line.
② If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a
single pressure of the cdef switch.
② If you change the PIXEL LEVEL for setting
the position, specify the pixel that moves by a
single pressure of the cdef switch.
③ In <SIZE>, press the SETUP switch and use
the cdef switch to adjust the size.
Press the SETUP switch again to complete the
sizing.
④ If you change the DIRECTION, you can specify
the detection direction. The detection direction
based on the defined two points will be
displayed on the screen.
④ In <LOCATION>, press the SETUP switch and
use the cdef switch to specify the position.
Press the SETUP switch again to complete
the positioning.
 Note :
– If you set the LINE of the FENCE to ON, PRIVACY 12 will
not be available.
Functions of FENCE, PIP, DIS and DIGITAL ZOOM (if the
digital zoom factor is set to larger than 1x) can not be
used simultaneously.
– In the boundary of the defined AREA and LINE, a FENCE
detection error may occur if two or more moving objects
overlap with each other or one object separates in
multiple directions.
- How to set the area
e
‹AREA‹
PIXEL LEVEL
[4]
<SIZE> <LOCATION>
• FIXED/MOVED
If an object on the screen suddenly disappears or
an object comes out of nowhere and stays for a
certain time, the area will be displayed.
① If you press the SETUP switch with the AREA
option set to ON, you can specify the position
and size of the area.
A detection (FIXED/MOVED) error may occur if :
- multiple motions occur continuously in random
directions
- a fixed object moves in one position continuously
- a second object screens the first moving object
English – 27
ENG
③ In <POINT>, you can specify the first position of
the line by pressing the SETUP switch once, and
the second position by pressing the switch again.
Use the cdef switch to specify the
position.
Set each position of the two points and press the
SETUP switch to complete the positioning.
How to use OSD Menu
❖ MASK AREA [1~4]
Specify a detection exception area to mask.
PRIVACY ZONE SETUP
Select a mask number and specify the size and
position.
ePRIVACY ZONEf
1
7
‹MASK AREA‹
2
8
3
9
4
10
PRIVACY SET
STYLE
<SIZE> <LOCATION>
5
11
❖ DISPLAY
[ON, OFF]
With the DISPLAY option set to ON, a motion or
a set ADVANCED function will be displayed on
the screen, if detected.
❖ SENSITIVITY
[1~7]
The PRIVACY function will protect your privacy by
screening the privacy area that you have specified
during monitoring. You can specify up to 12 privacy
zones.
If you set the PRIVACY SET to ON, your PRIVACY
ZONE settings will be applied.
You can change the style to adjust the mosaic size
and color of the PRIVACY ZONE.
ePRIVACY ZONEf
Set the sensitivity of the motion detection.
❖ RESOLUTION
[1~5]
If setting it to high, the camera can detect even a
trivial movement of the target.
28 – DIGITAL COLOR DOME CAMERA
6
12
ON
MOSAIC1
Us
PR
1
7
2
8
3
9
PRIVACY SET
STYLE
Y-LEVEL
RED
BLUE
4
10
5
11
6
12
ON
COLOR
[128]
[128]
[128]
Se
SE
sp
LE
How to use OSD Menu
Use the cdef switch to select one from
PRIVACY 1 through 12.
Select one from PRIVACY 1~12 and press the
SETUP switch to confirm your setting. You can
specify a pixel that moves as you change the PIXEL
LEVEL to set the position.
② Use the cdef switch to move the
position and press the SETUP switch to
confirm it.
 Note :
– If more than one PRIVACY ZONE is specified and the
PRIVACY SET is set to ON, the PIP function will be
deactivated.
‹PRIVACY ZONE SET1‹
PIXEL LEVEL
<POINT>
<POSITION>
① By pressing the SETUP switch in
<POSITION>, you can move the overall
position of the privacy zone.
[4]
- How to set the point
You can set each position of the 4 points.
① If you press the SETUP switch in <POINT>,
you will see the points available in the
PRIVACY ZONE. Each time you press the
SETUP switch, the points available will move.
② Use the cdef switch to set the position
of each point. Set each position of the four
points and press the SETUP switch to
complete the positioning.
- How to set the position
You can move the position of the overall area.
English – 29
ENG
– If the 12th PRIVACY ZONE is specified, the LINE function
of FENCE will be deactivated.
How to use OSD Menu
OTHER SET
eOTHER SETf
eSYSTEM INFOf
FACTORY DEFAULTS
OSD COLOR
BW
❖ FACTORY DEFAULTS
All the settings will be restored to the factory
default.
However, the settings of PROTOCOL, BAUD
RATE, ADDRESS and LANGUAGE will not be
restored to the default.
❖ OSD COLOR
❖
SYSTEM INFORMATION
TYPE
3_VAR_WDR_N
SERIAL NO. 000000000000000
CAMERA VER.
0.50_090101
You can check the system information such as
SERIAL NO and CAMERA VER.
LANGUAGE
[BW, R/G/B]
eLANGUAGEf
You can set the OSD(On-screen Display) color to
COLOR or B/W.
ÃENGLISH
FRANÇAIS
ESPAÑOL
日文
INGLÊS
The camera supports 5 different languages.
Select a preferred language.
30 – DIGITAL COLOR DOME CAMERA
How to use OSD Menu
❖ Initial Configuration Table
• Camera Configuration
CAMERA ID
OFF
VPS
OFF
IRIS
ALC
AGC
VERY HIGH
MOTION
DNR
(F.FAST)
MID
OFF
SENS-UP
AUTO x4
FLICKERLESS
(OFF)
XDR
MID
DAY/NIGHT
AUTO
DIGITAL ZOOM
OFF
DETAIL
[2]
AGC COLOR SUP
MID
REVERSE
H/V
POSI/NEGA
ENG
SHUTTER
+
PIP
OFF
DIS
OFF
V-SYNC
INT
English – 31
Specifications
SPECIFICATIONS
Items
Camera Type
Image
Scanning
Sub-items
Horizontal
Frequency
Vertical
Frequency
Min. Scene
Illumination
Functions
SCC-B5367N/SCC-B5367SN/SCC-B5369N/SCC-B5369SN
CCTV Camera (WDR & DAY/NIGHT)
Device
1/3” Super-HAD PS CCD
Total
811 x 508
Pixels
Effective
768 x 494
System
Interlace/Progressive
Scanning Line
525 lines
Frame
30frame/1sec
Internal Mode
15,734 Hz
Line-lock Mode
Internal Mode
Line-lock Mode
15,750 Hz
59.94 Hz
60 Hz
Sens-up
OFF
OFF
OFF
512 times
512 times
512 times
Condition
F No.
1.2
1.2
1.2
1.2
1.2
1.2
Number of Privacy Zone
Day/Night
Motion Detection
eXtended Dynamic Range(XDR)
Wide Dynamic Range(WDR)
Virtual Progressive Scan(VPS)
D-Zoom
PIP
High Speed Shutter
Flickerless
32 – DIGITAL COLOR DOME CAMERA
Level
50
30
15
50
30
15
IRE
IRE
IRE
IRE
IRE
IRE
Min. Scene illumination
DAY
NIGHT
0.4 Lux
0.04
0.24 Lux
0.024
0.12 Lux
0.012
0.0008 Lux
0.00008
0.00047 Lux
0.000047
0.00023 Lux
0.000023
12 (Polygonal Method)
DAY/NIGHT/AUTO/EXT
OFF/Tracking/Detection
Off/On (Level Setting)
Off/On (x128)
Off/On
x1 ~ x16 (x0.1 STEP)
Off/On
1/60 ~ 1/10Ksec (OSD)
Off/On
Lux
Lux
Lux
Lux
Lux
Lux
Specifications
Items
SCC-B5367N/SCC-B5367SN/SCC-B5369N/SCC-B5369SN
Video Output
S/N Ratio
Sens-Up
AGC
Line Lock
Camera ID
White Balance
Digital Noise Reduction(DNR)
Digital Image Stabilization(DIS)
Intelligent Video
Etc. Function
Horizontal
Vertical
S/N Ratio
x2 ~ x512
Off/On (Max.Level Setting)
Off/On (Phase Control)
Off/On (Max.54ea/2Line)
ATW1/ATW2/AWC/3200K/5600K
Off/On (Adaptive 3D+2D)
Off/On
Fixed/Moved, Fence
Detail, Reverse(H/V), Posi/Nega
600 TV Lines
350 TV Lines
VBS 1.0Vp-p, 75 Ω
Approx. 52dB
Lens
Lens Drive Type
Resolution
PAN
Range
TILT
Remote
Control
Range
Auto Iris (DC)
SCC-B5367 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2
SCC-B5369 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2
0 ~ 355°(100° in CW(Clockwise) direction,
255° in CCW (Counterclockwise) direction)
0 ~ 90°
Coaxitron (Data On Coax cable)
Yes (with SCX-RD100)
Environmental
Conditions
Operating Temperature
Humidity
-10˚C ~ +50˚C
Less than 90%
AC24V ± 10%(60Hz ± 0.3Hz)
DC12V ± 10%
about 2.6W
128(Ø) x 91(H)mm
Power
Power Requirement
Power Consumption
Dimensions (Ø x H)
Physical
Specification
Weight
330g
Color
SCC-B5367/SCC-B5369 : White
SCC-B5367S/SCC-B5369S : Silver
English – 33
ENG
Sub-items
N
Specifications
Items
Camera Type
Image
Scanning
Sub-items
Horizontal
Frequency
Vertical
Frequency
Min. Scene
Illumination
Functions
SCC-B5367P/SCC-B5367SP/SCC-B5369P/SCC-B5369SP
CCTV Camera (WDR & DAY/NIGHT)
Device
1/3” Super-HAD PS CCD
Total
795 x 596
Pixels
Effective
752 x 582
System
Interlace/Progressive
Scanning Line
625 lines
Frame
25frame/1sec
Internal Mode
15,625 Hz
Line-lock Mode
Internal Mode
Line-lock Mode
15,625 Hz
50 Hz
50 Hz
Sens-up
OFF
OFF
OFF
512 times
512 times
512 times
Condition
F No.
1.2
1.2
1.2
1.2
1.2
1.2
Number of Privacy Zone
Day/Night
Motion Detection
eXtended Dynamic Range(XDR)
Wide Dynamic Range(WDR)
Virtual Progressive Scan(VPS)
D-Zoom
PIP
High Speed Shutter
Flickerless
Sens-Up
BLC
34 – DIGITAL COLOR DOME CAMERA
Level
50
30
15
50
30
15
IRE
IRE
IRE
IRE
IRE
IRE
Min. Scene illumination
DAY
NIGHT
0.4 Lux
0.04
0.24 Lux
0.024
0.12 Lux
0.012
0.0008 Lux
0.00008
0.00047 Lux
0.000047
0.00023 Lux
0.000023
12 (Polygonal Method)
DAY/NIGHT/AUTO/EXT
OFF/Tracking/Detection
Off/On (Level Setting)
Off/On (x160)
Off/On
Max. x16
Off/On
1/50 ~ 1/10Ksec (OSD)
Off/On
x2 ~ x512
Off/On (Area Setting)
Lux
Lux
Lux
Lux
Lux
Lux
P
Specifications
Items
SCC-B5367P/SCC-B5367SP/SCC-B5369P/SCC-B5369SP
Video Output
S/N Ratio
AGC
Line Lock
Camera ID
White Balance
Digital Noise Reduction(DNR)
Digital Image Stabilization(DIS)
Intelligent Video
Etc. Function
Horizontal
Vertical
S/N Ratio
Off/On (Max.Level Setting)
Off/On (Phase Control)
Off/On (Max.54ea/2Line)
ATW1/ATW2/AWC/3200K/5600K
Off/On (Adaptive 3D+2D)
Off/On
Fixed/Moved, Fence
Detail, Reverse(H/V), Posi/Nega
600 TV Lines
350 TV Lines
VBS 1.0Vp-p, 75 Ω
Approx. 52dB
Lens
Lens Drive Type
Resolution
PAN
Range
TILT
Remote
Control
Range
Auto Iris (DC)
SCC-B5367 : focal length = 2.5 to 6.0mm / Aperture ratio = F 1.2
SCC-B5369 : focal length = 2.8 to 11.0mm / Aperture ratio = F 1.2
0 ~ 355°(100° in CW(Clockwise) direction,
255° in CCW (Counterclockwise) direction)
0 ~ 90°
Coaxitron (Data On Coax cable)
Yes (with SCX-RD100)
Environmental
Conditions
Operating Temperature
Humidity
-10˚C ~ +50˚C
Less than 90%
AC24V ± 10%(50Hz±0.3Hz)
DC12V ± 10%
about 2.6W
128(Ø) x 91(H)mm
330g
SCC-B5367/SCC-B5369 : White
SCC-B5367S/SCC-B5369S : Silver
Power
Physical
Specification
Power Requirement
Power Consumption
Dimensions (Ø x H)
Weight
Color
English – 35
ENG
Sub-items